Bump pm80xx driver version to 0.1.38.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The request has to be retried incase if the length of the SSP
Response IU is invalid.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
If the link error happens, we don't need to disconnect the phy,
which will remove the drive. Instead acknowledging the controller
and logging the error will be enough.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In pm8001_ccb_task_free(), the dma unmapping is done based on
ccb->n_elem value. This should be initialized to zero in the
task_abort(). Otherwise, pm8001_ccb_task_free() will try for
dma_unmap_sg() which is invalid for task abort and can lead to
kernel crash.
Changes From V1:
None
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Thermal page code has been changed to 7 for the 12G controllers.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In Nexus reset the device state request are not needed.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Updated 12G linkrate to libsas.
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Reviewed-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Company has policy to use company email address, so update
my email address to company address.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use logical instead of bitwise AND.
Signed-off-by: Sebastian Herbszt <herbszt@gmx.de>
Reviewed-by: James Smart <james.smart@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Invoking get_cmd_state for qla2xxx always returns 0. Instead change it
to return the actual fabric state from qla_tgt_cmd. This will help with
debugging.
Signed-off-by: Dilip Kumar Uppugandla <dilip@purestorage.com>
Signed-off-by: Spencer Baugh <sbaugh@catern.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The driver is calling hpsa_shutdown before calling scsi_remove_host.
hpsa_shutdown is disabling interrupts.
scsi_remove_host can trigger I/O operations, such as
SYNCHRONIZE CACHE when multipath is enabled which hang the system.
Call scsi_remove_host before calling hpsa_shutdown.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
A regression was introduced into the hpsa driver a while back so
non-zero LUNs of multi-LUN devices may no longer be presented via
a SAS based Smart Array. I have not done a bisection to discover
the change that caused it.
The CISS firmware specification (available on sourceforge)
defines an 8 byte lunid that describes devices that the Smart
Array can see/present to the system. The current code in the hpsa
driver attempts to find matches for non-zero LUNs with LUN 0 for
a bus/target by zeroing out byte 4 of the lunid and find a match.
This method is sufficient for SCSI based Smart Arrays because
byte 5 is always 0. For SAS based Smart arrays byte 5 of the
lunid contains the path number for a multipath device and
either one or two bits (the documentation does not define how
many bits are used but it appears it may be one only) that
indicate if the given path number in byte 5 must always be
used to access that device. Byte 5 may not always be zero.
The following are lunids (spaces added for clarity) for a
MSL2024 single drive library connected via a H241 Smart Array:
00 00 00 00 01 00 00 01 (changer)
00 00 00 00 00 80 00 01 (tape)
In the 4th byte (counting from 0) you can see that the tape
is LUN 0 and the changer is LUN 1. The 0x80 set in the 5th byte
for the tape drive means the driver should force access to
path 0 (the library in this case was connected to one path only
anyway).
After the changes we can see the following in the dmesg output:
scsi 0:3:0:0: RAID HP H241 1.18 \
PQ: 0 ANSI: 5
scsi 0:2:0:0: Sequential-Access HP Ultrium 6-SCSI 354W \
PQ: 0 ANSI: 6
scsi 0:2:0:1: Medium Changer HP MSL G3 Series 8.70 \
PQ: 0 ANSI: 5
Showing that the changer is correctly identified as LUN 1 of
bus 2 target 0. Before the change the changer device is not seen.
Suggested-by: shane.seymour <shane.seymour@hp.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
prevent adding volumes that are not available.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
showing that tables have been updated unnecessarily.
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
host no, bus, target, lun, scsi_device_type
for hba mode add: box and bay information
report if the path is active/inactive
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
need to add PMC to copyright notice and update the Hewlett-Packard
copyright notification.
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Justin Lindley <justin.lindley@pmcs.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Scott Teel <scott.teel@pmcs.com>
Reviewed-by: Kevin Barnett <kevin.barnett@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@pmcs.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Driver crashes if the BIOS do not set up at least one
memory I/O resource. This failure can happen if the device is too
slow to respond during POST and is missed by the BIOS, but Linux
then detects the device later in the boot process.
Based on a patch from Timothy Pearson <tpearson@raptorengineeringinc.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Surround conditional locking statements with "#ifndef __CHECKER__" /
"#endif" to hide these for the sparse static source code analysis
tool.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
The "return QLA_SUCCESS" statement just above the "fw_load_failed"
label cannot be reached, hence remove it. Additionally remove the
"else" keyword since the code block below the if-statement ends
with a return statement.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Avoid that smatch reports the following warning:
drivers/scsi/qla2xxx/qla_attr.c:1081: qla2x00_model_desc_show() warn: this array is probably non-NULL. 'vha->hw->model_desc'
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch removes 21 casts between an __iomem pointer type and
another data type but also introduces five new casts (see also
the casts with "__force"). Although this patch does not change
any functionality, IMHO the code with __force casts needs further
review.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Whether htonl() or __constant_htonl() is used, if the argument
is a constant the conversion happens at compile time. Hence leave
out the __constant_ prefix for this and other endianness
conversion functions. This improves source code readability.
[jejb: checkpatch fixes]
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Replace the QLA82XX_ADDR_IN_RANGE() and QLA8044_ADDR_IN_RANGE() macros
with the inline function addr_in_range(). This avoids that the compiler
reports the following warning when building with W=1: comparison of
unsigned expression >= 0 is always true.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Detected these variables by building with W=1.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Let the debug statement in qlafx00_tm_iocb_entry() report both rsp_info
and rsp_info_len instead of reporting rsp_info_len twice.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use dev_printk() when possible to make messages more useful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Use dev_printk() when possible to make messages more useful.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Sumit Saxena <sumit.saxena@avagotech.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Log the ALUA state change unit attention correctly with
the message log and emit an event to allow user-space
tools to react to it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
These are signed values the come from the user, we put a cap on the
upper bounds but not on the lower bounds.
We use "karg.dataSgeOffset" to calculate "sz". We verify "sz" and
proceed as if that means that "karg.dataSgeOffset" is correct but this
fails to consider that the "sz" calculations can have integer overflows.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Comment in struct Scsi_Host says that drivers are not supposed to access
__devices directly. storvsc_host_scan() doesn't happen in irq context
so we can just use shost_for_each_device().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Long Li <longli@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Under the 'default' case in scmnd->sc_data_direction we have 3 options:
- DMA_NONE which we handle correctly.
- DMA_BIDIRECTIONAL which is never supposed to be set by SCSI stack.
- Garbage value.
Do WARN() and return -EINVAL in the last two cases. virtio_scsi does
BUG_ON() here but it looks like an overkill.
Reported-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Convert DRIVER_ATTR macros to DRIVER_ATTR_RO requested by
Greg KH. Also switched to using scnprintf instead of snprintf
per Documentation/filesystems/sysfs.txt.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Support HighPoint RR36xx HBAs which are based on Marvell Frey.
Support SAS tape and SAS media changer.
[jejb: remove now unused label]
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
This patch changes the st driver to use attribute groups so
driver sysfs files are created automatically. See the
following for reference:
http://kroah.com/log/blog/2013/06/26/how-to-create-a-sysfs-file-correctly/
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Resources allocated within bfad_im_port_index idr are not deallocated
on module unload. The patch adds idr_destroy() in exit function.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
In case pci_resource_start() or pci_resource_len() reutrn 0, mvsas_ioremap
returns without doing an iounmap() of mvi->regs_ex.
Found by the cocinelle tool.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Commit f3ddac1918 ("[SCSI] qla2xxx:
Disable adapter when we encounter a PCI disconnect.") has introduced a
code that disables the board, releasing some resources, when reading
0xffffffff.
In case this happens when there is an EEH, this read will trigger EEH
detection and set PCI channel offline. EEH will be able to recover the
card from this state by doing a reset, so it's a better option than
simply disabling the card.
Since eeh_check_failure will mark the channel as offline before
returning the read value, in case there really was an EEH, we can simply
check for pci_channel_offline, preventing the board_disable code from
running if it's true.
Without this patch, EEH code will try to access those same resources
that board_disable will try to free. This race can cause EEH recovery to
fail.
[ 504.370577] EEH: Notify device driver to resume
[ 504.370580] qla2xxx [0001:07:00.0]-9002:2: The device failed to resume I/O from slot/link_reset.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
SCSI device driver to support filesystem access on the IBM CXL Flash adapter.
Supported-by: Stephen Bates <stephen.bates@pmcs.com>
Reviewed-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Matthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: Manoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Viswas G