Part of the include cleanups means that the implicit
inclusion of module.h via device.h is going away. So
fix things up in advance.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The raid6 recovery code should immediately drop back to the optimized
synchronous path when a p+q dma resource is not available. Otherwise we
run the non-optimized/multi-pass async code in sync mode.
Verified with raid6test (NDISKS=255)
Applies to kernels >= 2.6.32.
Cc: <stable@kernel.org>
Acked-by: NeilBrown <neilb@suse.de>
Reported-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The raid6 recovery code currently requires special handling of the
4-disk and 5-disk recovery scenarios for the native layout. Quoting
from commit 0a82a623:
In these situations the default N-disk algorithm will present
0-source or 1-source operations to dma devices. To cover for
dma devices where the minimum source count is 2 we implement
4-disk and 5-disk handling in the recovery code.
The ddf layout presents disks=6 and disks=7 to the recovery code in
these situations. Instead of looking at the number of disks count the
number of non-zero sources in the list and call the special case code
when the number of non-failed sources is 0 or 1.
[neilb@suse.de: replace 'ddf' flag with counting good sources]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
md/raid6 passes a list of 'struct page *' to the async_tx routines,
which then either DMA map them for offload, or take the page_address
for CPU based calculations.
For RAID6 we sometime leave 'blanks' in the list of pages.
For CPU based calcs, we want to treat theses as a page of zeros.
For offloaded calculations, we simply don't pass a page to the
hardware.
Currently the 'blanks' are encoded as a pointer to
raid6_empty_zero_page. This is a 4096 byte memory region, not a
'struct page'. This is mostly handled correctly but is rather ugly.
So change the code to pass and expect a NULL pointer for the blanks.
When taking page_address of a page, we need to check for a NULL and
in that case use raid6_empty_zero_page.
Signed-off-by: NeilBrown <neilb@suse.de>
If we are unable to offload async_mult() or async_sum_product(), then
unmap the buffers before falling through to the synchronous path.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Some engines optimize operation by reading ahead in the descriptor chain
such that descriptor2 may start execution before descriptor1 completes.
If descriptor2 depends on the result from descriptor1 then a fence is
required (on descriptor2) to disable this optimization. The async_tx
api could implicitly identify dependencies via the 'depend_tx'
parameter, but that would constrain cases where the dependency chain
only specifies a completion order rather than a data dependency. So,
provide an ASYNC_TX_FENCE to explicitly identify data dependencies.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
async_raid6_2data_recov() recovers two data disk failures
async_raid6_datap_recov() recovers a data disk and the P disk
These routines are a port of the synchronous versions found in
drivers/md/raid6recov.c. The primary difference is breaking out the xor
operations into separate calls to async_xor. Two helper routines are
introduced to perform scalar multiplication where needed.
async_sum_product() multiplies two sources by scalar coefficients and
then sums (xor) the result. async_mult() simply multiplies a single
source by a scalar.
This implemention also includes, in contrast to the original
synchronous-only code, special case handling for the 4-disk and 5-disk
array cases. In these situations the default N-disk algorithm will
present 0-source or 1-source operations to dma devices. To cover for
dma devices where the minimum source count is 2 we implement 4-disk and
5-disk handling in the recovery code.
[ Impact: asynchronous raid6 recovery routines for 2data and datap cases ]
Cc: Yuri Tikhonov <yur@emcraft.com>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Andre Noll <maan@systemlinux.org>
Acked-by: Maciej Sosnowski <maciej.sosnowski@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Paul Gortmaker