Commit Graph

388399 Commits

Author SHA1 Message Date
Alexander Shiyan 1c04ab0f0f ARM: dts: i.MX27: Disable AUDMUX in the template
AUDMUX expects additional parameters to be configured correctly,
so turn it off into a template.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:55 +08:00
Tony Prisk a338be9ad7 ARM: dts: wandboard: Add support for SDIO bcm4329
The wandboard has a Broadcom 4329 WiFi connected via SDIO. This patch
sets the required pins to enable the wifi module.

Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:54 +08:00
Alexander Shiyan 677e28b1cc ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
External high frequency clock CKIH1 is optional for i.MX51, so move
it setup into boards where it is used.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:53 +08:00
Fabio Estevam c574fa93af ARM: dts: imx53-qsb: Make USBH1 functional
mx53qsb uses GPIO7_8 to turn on VBUS, so add support for it.

Also specify the PHY type in the device tree.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:51 +08:00
Philipp Zabel 1e44d3f880 ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
This patch enables I2C1 and adds device tree nodes for the EEPROM and the
DA9063 PMIC connected to this I2C bus.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:50 +08:00
Philipp Zabel 9273ee3528 ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:48 +08:00
Fabio Estevam 38501179c9 ARM: dts: imx6qdl-sabresd: Add touchscreen support
mx6 sabresd boards have a egalax touchscreen controller connected via I2C3.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:47 +08:00
Shawn Guo ea257a0328 ARM: imx: add ocram clock for imx53
Add missing ocram gate clock for imx53 and also represent it in device
tree ocram node.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:46 +08:00
Shawn Guo 951ebf58bf ARM: dts: imx: ocram size is different between imx6q and imx6dl
The ocram on imx6q is 256 KiB while on imx6dl it's 128 KiB.  Let's
have separate node for imx6q and imx6dl.  It also changes imx6q size
0x3f000 to 0x40000 to match the hardware.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Liu Ying <Ying.Liu@freescale.com>
2013-08-22 23:29:44 +08:00
Alexander Shiyan e9c1786681 ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
Outputs regulator SW1A and SW1A, SW2A and SW2B are connected together,
so it determined as "joined" operation for MC13783. Separate work of
these outputs in this case would be wrong, so we define only one of
the outputs.
Additionally, define the full range of voltages for the CPU (1.2v - 1.52v).

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:43 +08:00
Alexander Shiyan 2885e48ca0 ARM: dts: i.MX27: Remove clock name from CPU node
Clock name is not needed for "cpufreq-cpu0".

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:41 +08:00
Alexander Shiyan 8defcb5376 ARM: dts: i.MX27: Increase "clock-latency" value
i.MX27 CPU can be clocked with a 32 kHz quartz, and not just 32768 Hz,
so increase "clock-latency" value, which will ensure that we use two
clock cycles on frequency change.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:40 +08:00
Alexander Shiyan 48568be649 ARM: dts: i.MX27: Add label to CPU node
Add a label to i.MX27 CPU node. This change allows the reuse this node
in the upper levels of the DTS.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:39 +08:00
Alexander Shiyan c0b357c042 ARM: dts: i.MX27: Remove optional "ptp" clock source for FEC
Patch removes optional "ptp" clock source for FEC. This clock is
missing in i.MX27.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:38 +08:00
Alexander Shiyan 3c0e2a227e ARM: dts: i.MX27: Using "wdog_ipg_gate" clock source for watchdog
Patch replaces "dummy" clock source for watchdog with "wdog_ipg_gate".

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:36 +08:00
Fabio Estevam 6c30640dc2 ARM: dts: imx6qdl-sabresd: Allow buttons to wake-up the system
This is useful for testing suspend/resume sequence.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:35 +08:00
Shawn Guo a94f8ecb2f ARM: imx6q: remove board specific CLKO setup
The CLKO is widely used by imx6q board designs to clock audio codec.
Since most codecs accept 24 MHz frequency, let's initially set up CLKO
with OSC24M (cko <-- cko2 <-- osc).  Then those board specific CLKO
setup for audio codec can be removed.

The board dts files also need an update on cko reference in codec node.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:34 +08:00
Shawn Guo 5da826abe9 ARM: dts: imx: use generic DMA bindings for SSI nodes
Updates SSI nodes to adopt generic DMA bindings.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:32 +08:00
Shawn Guo b7fb7105b2 ARM: dts: imx: add LVDS panel for imx6qdl-sabresd
Add HannStar HSD100PXN1 XGA panel support on LVDS1 port of
imx6qdl-sabresd board.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:31 +08:00
Fabio Estevam 213a8404c4 ARM: dts: imx6q-wandboard: Add sata support
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:30 +08:00
Fabio Estevam 2688a32f98 ARM: dts: imx6: Add support for imx6q wandboard
Add support for the imx6q wanboard variant.

Since imx6q/dl are pin to pin compatible, introduce the imx6qdl-wandboard.dtsi
file that contains the common peripheral nodes.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:28 +08:00
Shawn Guo 3fe6373b42 ARM: dts: imx: add tempmon node for imx6q thermal support
Mark ocotp as a syscon node and add tempmon for imx6q thermal support.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:27 +08:00
Shawn Guo c7aa12a62c ARM: dts: imx: remove old DMA binding data from gpmi node
After mxs-dma driver adopts generic DMA device tree binding, gpmi
channel interrupt number is defined in DMA controller node, and
channel ID is listed in "dmas" property.  So the DMA channel interrupt
number in gpmi node "interrupts" property and fsl,gpmi-dma-channel which
are used by old customized DMA binding can be removed now.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
2013-08-22 23:29:26 +08:00
Richard Zhu 0fb1f80426 ARM: dtsi: enable ahci sata on imx6q platforms
Only imx6q has the ahci sata controller, enable
it on imx6q platforms.

Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:25 +08:00
Alexander Shiyan 98a3e804de ARM: dts: imx27: Add core voltages
This patch adds core voltages for i.MX27 CPUs. Only 266 and 400 MHz modes
is documented in the datasheet, so we add a 266 MHz frequency for conform this.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:23 +08:00
Alexander Shiyan edd052865d ARM: dts: i.MX51: Add WEIM node
This patch adds the missing (Wireless External Interface Module) WEIM
devicetree node for i.MX51 CPUs.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:22 +08:00
Fabio Estevam 4debd068a5 ARM: dts: imx6dl-wandboard: Add support for UART3
Wandboard has a bluetooth device connected to UART3, so add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:21 +08:00
Fabio Estevam c3cb6b6b1a ARM: dts: imx6dl-wandboard: Add SDHC1 and SDHC2 ports
Wandboard has a SD card slot on the baseboard connected to SDHC1 and a
BCM4329 (Wifi + Bluetooth chip) connected to SDHC2.

Add support for these ports.

While at it, provide the card detect gpio on SDHC3 and also fix indentation on
MX6QDL_PAD_GPIO_0__CCM_CLKO1 hog pin.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:20 +08:00
Fabio Estevam 5ff88341cf ARM: dts: imx6qdl.dtsi: Add another uart3 pin group
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:18 +08:00
Fabio Estevam 26c3b65da4 ARM: dts: imx6qdl.dtsi: Add usdhc1 pin groups
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:17 +08:00
Huang Shijie 72a5cebfa1 ARM: dts: imx6qdl/imx6sl: add the dma property for uart
Add the dma property for all the uart.

Note: Add the dma property does not mean we enable the dma for this
uart.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:16 +08:00
Matthias Weisser c770f7c020 ARM: dts: imx25: Make lcdc compatible to imx21 fb
Make lcdc compatible to imx21 fb.

Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:15 +08:00
Huang Shijie c2797984ea ARM: dts: imx6qdl: add a new pinctrl for uart3
Add the a new pinctrl for uart3. In the imx6q{dl}-sabreauto boards,
the uart3 is used for Bluetooth.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:13 +08:00
Shawn Guo b72ce929d2 ARM: dts: add more imx6q/dl pin groups
Add more imx6q/dl pin groups for those supported boards, e.g. sabresd,
sabreauto, arm2.

IPU2 pin groups are added into imx6q.dtsi, since the block is only
available on imx6q.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:12 +08:00
Shawn Guo c56009b2f6 ARM: dts: imx: share pad macro names between imx6q and imx6dl
The imx6q and imx6dl are two pin-to-pin compatible SoCs.  The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.

We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips.  This brings a maintenance burden on having the same label point
to the same pin group defined in two places.

The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names.  Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.

Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:11 +08:00
Huang Shijie 51056d9cff ARM: dts: enable the uart2 for imx6q-arm2
enable the uart2 for imx6q-arm2 board.
The uart2 works in the DTE mode, with the RTS/CTS and DMA enabled.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:09 +08:00
Huang Shijie a0bffd0cac ARM: dts: imx6q{dl}: add a DTE uart pinctrl for uart2
In the arm2 board, the UART2 works in the dte mode.
So add a pinctrl for both the imx6q{dl} boards.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:08 +08:00
Huang Shijie 0b7a76aaa8 ARM: dts: imx6q{dl}: add DTE pads for uart
The uart2 in the imx6q-arm2 board is used as a DTE uart,
this patch adds the necessary DTE pads for uart2.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:07 +08:00
Huang Shijie 6eb85f9196 ARM: dts: imx6sl: add "fsl,imx6q-uart" for uart compatible
In order to enable the DMA for some uart port in imx6sl, we add the
"fsl,imx6q-uart" to the uart's compatible property.

Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:06 +08:00
Markus Pargmann 38918b7275 ARM: dts: imx27 phyCARD-S, i2c ADC device node
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:05 +08:00
Markus Pargmann b9d6bfaabc ARM: dts: imx27 phyCARD-S, move i2c1 and owire to rdk
Both buses are not used on the phyCARD-S module. This patch moves them
to the rdk file. Remove ioexpander.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:03 +08:00
Markus Pargmann 51a0102fd0 ARM: dts: imx27 phyCARD-S SOM remove wrong i2c sensor
This sensor was introduced in the original pca100 board file, but
phyCARD-S SOM and RDK do not have a temperature sensor.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:02 +08:00
Fabio Estevam 070bd7e491 ARM: dts: imx: Add the missing cpus node
To make it consistent with the other i.mx SoCs, let's add the cpus nodes.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:01 +08:00
Fabio Estevam eda5fe8bd7 ARM: dts: imx6dl-wandboard: Add audio support
Wandboard has a sgtl5000 codec.

Add audio support.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:29:00 +08:00
Markus Pargmann be89e1a0bf ARM: dts: imx27 phyCARD-S remove wrong I2C RTC
Fixup of commit "ARM: dts: Add device tree support for phycard pca100".

Remove wrong I2C RTC node.

Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:28:58 +08:00
Alexander Shiyan f0d8e3f186 ARM: dts: imx27-phytec-phycore-som: Using labels for reusing UART, I2C and FEC
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:28:57 +08:00
Alexander Shiyan 52303d136c ARM: dts: imx27-phytec-phycore-rdk: Add CAN node
This patch adds CAN (NXP SJA1000) node for Phytec PCM-970 RDK.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:28:56 +08:00
Alexander Shiyan cff2a71365 ARM: dts: imx27-phytec-phycore-som: Add SRAM node
This patch adds SRAM node for Phytec PCM-038 module.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:28:55 +08:00
Alexander Shiyan 984d6fc313 ARM: dts: imx27-phytec-phycore-som: Add WEIM node
This patch adds WEIM node for Phytec PCM-038 module.
Migrate existing on-module NOR-flash as children of WEIM CS0.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:28:54 +08:00
Alexander Shiyan 0912f59474 ARM: dts: i.MX27: Add WEIM node
This patch adds the missing (Wireless External Interface Module) WEIM
devicetree node for i.MX27 CPUs.

Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-22 23:28:53 +08:00