Commit Graph

56 Commits

Author SHA1 Message Date
Alex Deucher 8e36ed0084 drm/radeon/kms: hpd cleanup
- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-05-19 10:31:41 +10:00
Dave Airlie 05ea893c46 Merge remote branch 'anholt/drm-intel-next' into drm-next
* anholt/drm-intel-next: (515 commits)
  drm/i915: Fix out of tree builds
  drm/i915: move fence lru to struct drm_i915_fence_reg
  drm/i915: don't allow tiling changes on pinned buffers v2
  drm/i915: Be extra careful about A/D matching for multifunction SDVO
  drm/i915: Fix DDC bus selection for multifunction SDVO
  drm/i915: cleanup mode setting before unmapping registers
  drm/i915: Make fbc control wrapper functions
  drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
  drm/i915: Use spatio-temporal dithering on PCH
  [MTD] Remove zero-length files mtdbdi.c and internal.ho
  pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
  libata: Fix several inaccuracies in developer's guide
  slub: Fix bad boundary check in init_kmem_cache_nodes()
  raid6: fix recovery performance regression
  KEYS: call_sbin_request_key() must write lock keyrings before modifying them
  KEYS: Use RCU dereference wrappers in keyring key type code
  KEYS: find_keyring_by_name() can gain access to a freed keyring
  ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
  ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
  ALSA: take tu->qlock with irqs disabled
  ...
2010-05-19 09:35:51 +10:00
Ben Skeggs 68adac5e49 drm: move radeon_fixed.h to shared drm_fixed.h header
Will be used by nouveau driver also in the near future.

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-05-18 18:21:33 +10:00
Dave Airlie eb1f8e4f3b drm/fbdev: rework output polling to be back in the core. (v4)
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.

v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.

v3: add config lock take inside polling, add intel/nouveau poll init/fini calls

v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.

glisse: discard drm_helper_hpd_irq_event

v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-05-18 17:40:11 +10:00
Eric Anholt 34dc4d4423 Merge remote branch 'origin/master' into drm-intel-next
Conflicts:
	drivers/gpu/drm/i915/i915_dma.c
	drivers/gpu/drm/i915/i915_drv.h
	drivers/gpu/drm/radeon/r300.c

The BSD ringbuffer support that is landing in this branch
significantly conflicts with the Ironlake PIPE_CONTROL fix on master,
and requires it to be tested successfully anyway.
2010-05-10 13:36:52 -07:00
Alex Deucher 3515387ba9 drm/radeon/kms: fix panel scaling adjusted mode setup
This should duplicate exactly what the ddx does for both
legacy and avivo.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-05-05 11:27:59 +10:00
Christian König 58bd086313 drm/radeon/kms: rework audio polling timer
Rework HDMI audio polling timer, only enable it when
at least one HDMI encoder needs it. Preparation for
replacing it with irq support.

Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-04-23 14:11:17 +10:00
Dave Airlie 5c4426a782 drm/kms/fb: add polling support for when nothing is connected.
When we are running in a headless environment we have no idea what
output the user might plug in later, we only have hotplug detect
from the digital outputs. So if we detect no connected outputs at
initialisation, start a slow work operation to poll every 5 seconds
for an output.

this is only hooked up for radeon so far, on hw where we have full
hotplug detection there is no need for this.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-04-07 10:29:52 +10:00
Dave Airlie 8be48d924c drm/kms/fb: move to using fb helper crtc grouping instead of core crtc list
This move to using the list of crtcs in the fb helper and cleans up the
whole picking code, now we store the crtc/connectors we want directly
into the modeset and we use the modeset directly to set the mode.

Fixes from James Simmons and Ben Skeggs.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-04-07 10:24:56 +10:00
Dave Airlie 386516744b drm/fb: fix fbdev object model + cleanup properly.
The fbdev layer in the kms code should act like a consumer of the kms services and avoid having relying on information being store in the kms core structures in order for it to work.

This patch

a) removes the info pointer/psuedo palette from the core drm_framebuffer structure and moves it to the fbdev helper layer, it also removes the core drm keeping a list of kernel kms fbdevs.
b) migrated all the fb helper functions out of the crtc helper file into the fb helper file.
c) pushed the fb probing/hotplug control into the driver
d) makes the surface sizes into a structure for ease of passing
This changes the intel/radeon/nouveau drivers to use the new helper.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-04-07 10:21:03 +10:00
Alex Deucher ac1aade687 drm/radeon/kms: use new pre/post_xfer i2c bit algo hooks
This allows us to remove the internal bit algo bus used by
the radeon i2c algo.  We now register a radeon algo adapter
if the gpio line is hw capable and the hw inplementation is
available, otherwise we register a bit algo adapter.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-03-31 14:55:50 +10:00
Rafał Miłecki 808032ee29 drm/radeon/kms: clean HDMI definitions
We already know same offsets are used for different encoders/transmitters, so
just numeric them instead naming incorrectly. Additionaly we found additional
registers needed for RV770+

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-03-15 10:01:40 +10:00
Alex Deucher 86cb2bbfda drm/radeon/kms: use lcd pll limits when available
The bios has alternate pll output limits for LCD panels.
If available, use these for pll divider calculations.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-03-15 09:56:46 +10:00
Alex Deucher 383be5d178 drm/radeon/kms: update new pll algo
- add support for pre-avivo chips
- add support for fixed post/ref dividers
- add support for non-fractional fb dividers

By default avivo chips use the new algo and
pre-avivo chips use the old algo. Use the "new_pll"
module option to toggle between them.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-02-25 11:38:06 +10:00
Alex Deucher bcc1c2a1d2 drm/radeon/kms: add initial Evergreen support (Radeon HD 5xxx)
This adds initial Evergreen KMS support, it doesn't include
any acceleration features or interrupt handling yet.

Major changes are DCE4 handling for PLLs for the > 2 crtcs.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-02-09 09:44:02 +10:00
Alex Deucher 7c27f87d2b drm/radeon/kms: rework pll algo selection
Rework the pll algo selection so that the pll algo
in use can be selected more easily.  This allows
us to select different pll divider selection algos
for specific monitors that work better with one algo
or the other.  This is needed for the next patch which
adds an LVDS pll quirk for a specific notebook.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-02-09 09:31:21 +10:00
Alex Deucher 3c537889e1 drm/radeon/kms: add support for hardcoded edids in rom (v2)
Some servers hardcode an edid in rom so that they will
work properly with KVMs.  This is a port of the relevant
code from the ddx.

[airlied: reworked to validate edid at boot stage - and
remove special quirk, if there is a valid EDID in the BIOS rom
we'll just try and use it.]

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-02-09 09:31:20 +10:00
Alex Deucher 5a6f98f5bf drm/radeon/kms: add radeon i2c algo
Currently just a wrapper around bit algo

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-02-05 15:10:19 +10:00
Dave Airlie f28cf33945 drm/kms/radeon: pick digitial encoders smarter. (v3)
booting a Lenovo W500 with LVDS + DP outputs showed up a TODO we had
on our list, to pick a correct digital encoder block. The LVTMA
encoder requires the second digital encoder, all others can use any
encoder at all.

This fixes the digital encoder selection logic to enable LVDS/DP combos
to work okay.

V2: fix silly addition of connector dig_block and cleanup the other
places in the code that pick the encoder.

V3: rename to dig_encoder and clean up further - also fix
the picking algorithm.

tested on Lenovo W500 + desktop 3650 cards.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-02-01 10:13:15 +10:00
Alex Deucher fc10332b8a drm/radeon/kms: clean up pll struct
- add a new flag for fixed post div
- pull the pll flags into the struct

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-01-24 17:24:23 +10:00
Alex Deucher 615e0cb679 drm/radeon/kms/r4xx: cleanup atom path
most of radeon_legacy_atom_set_surface() is taken care
of in atombios_set_base(), so remove the duplicate
setup and move the remaining bits (DISP_MERGE setup and
FP2 sync) to atombios_crtc.c where they are used.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
2010-01-21 08:40:08 +10:00
Alex Deucher a5899fcc18 drm/radeon/kms: fix typo in atom connector type handling
Also remove the problematic enums that were unused
remnants from the ddx.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2010-01-08 13:03:18 +10:00
Alex Deucher d79766fab9 drm/radeon/kms: set proper default tv standard
we were just using 1 before.

reported on irc by soreau

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-23 11:14:03 +10:00
Christian Koenig dafc3bd515 drm/radeon/kms: HDMI support for R600 KMS
Adding basic HDMI support for R600 KMS, ported from radeonhd ddx.

[airlied:- checkpatch cleanups]
Signed-off-by: Christian Koenig <deathsimple@vodafone.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-16 15:46:48 +10:00
Alex Deucher b27b63750d drm/radeon/kms/avivo: add support for new pll selection algo
Supported on all AVIVO-based asics.
Can be disabled via the new_pll module parameter:
new_pll=0 - disable
new_pll=1 - enable
enabled by default

[airlied: fixed to use do_div]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
2009-12-10 15:09:05 +10:00
Alex Deucher d4877cf229 drm/radeon/kms: enable hpd support
This enabled interrupt driven hpd support for all
radeon chips.  Assuming the hpd pin is wired up
correctly, the driver will generate uevents on
digital monitor connect and disconnect and retrain
DP monitors automatically.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:48:22 +10:00
Alex Deucher eed45b30cd drm/radeon/kms: get HPD info for connectors
This populates the connectors with HPD (Hot Plug Detect)
information.  This will be used in subsequent patches
for automatic digital monitor connect/disconnect handling.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:46:28 +10:00
Alex Deucher 9fa05c98d6 drm/radeon/kms: fix DP detect
only return connected if there is actually a
monitor connected.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:48 +10:00
Alex Deucher 5801ead6bd drm/radeon/kms: add support for DP modesetting
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:44 +10:00
Alex Deucher f92a8b6758 drm/radeon/kms: handle dp sinks in atom encoder/transmitter tables
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:43 +10:00
Alex Deucher 4143e919ea drm/radeon/kms: store sink type in atom dig connector
This will be used laster when the encoder and transmitters
are set up.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:42 +10:00
Alex Deucher 6a93cb250a drm/radeon/kms: i2c reorg
- keep the atom i2c id in the i2c rec
- fix gpio regs for GPIO and MDGPIO on pre-avivo chips
- track whether the i2c line is hw capable
- track whether the i2c line uses the multimedia i2c block

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:41 +10:00
Alex Deucher 1a66c95a64 drm/radeon/kms: DP fixes and cleanup from the ddx
- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:40 +10:00
Dave Airlie 746c1aa4d1 drm/radeon/kms: initial radeon displayport porting
This is enough to retrieve EDID and DPCP.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-08 10:22:31 +10:00
Alex Deucher 32f48ffea9 drm/radeon/kms: fix LVDS setup on r4xx
R4xx mobility chips use atombios, which does not store
the LVDS_GEN_CNTL parameter setup like combios.  Rather,
it's configured in LVDSEncoderControl.  As such,
LVDS_GEN_CNTL is set wrong when on resume.  Call
LVDSEncoderControl to set it properly.

Should fix fdo bug 25336

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-02 11:37:13 +10:00
Dave Airlie 1f3b6a45f0 drm/radeon/kms: add support for encoder cloning.
The RN50 really needs this since its a single crtc card,
however other gpus may benefit from it as well.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-02 11:37:09 +10:00
Alex Deucher 80297e87bc drm/radeon/kms: rework scaler handling
Keep requested scaler type in radeon_encoder
and the actual scaler type used in radeon_crtc.
This prevents us from enabling the scaler when it's
not required (i.e., the requested mode is the native
mode).  Also, always set the adjusted mode equal
to the native mode for lvds.

Should fix:
https://bugzilla.redhat.com/show_bug.cgi?id=522271

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-02 11:36:43 +10:00
Alex Deucher fcec570b27 drm/radeon/kms: add support for external tmds on legacy boards
This enables initialization of external tmds chips on pre-atom
and mac systems.  Macs are untested.  Also, some macs have single
link tmds chips while others have dual link tmds chips.  We need
to figure out which ones have which.

This gets external TMDS working on my RS485 and RV380.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-02 11:36:40 +10:00
Alex Deucher 9b9fe72488 drm/radeon/kms: clean up i2c
- Change reg/mask names to match what we use internally
and in the bios
- Clarify how i2c over gpio on radeon actually works

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-02 11:36:39 +10:00
Alex Deucher ab1e9ea08f drm/radeon/kms: dont't pass a radeon_connector to radeon_i2c_do_lock()
We need this for supporting things other than ddc on i2c.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-12-02 11:36:38 +10:00
Alex Deucher b75fad0682 drm/radeon/kms: store detailed connector info
This will be useful for mode validation and certain
atom tables.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-11-06 11:35:30 +10:00
Mathias Fröhlich 61c4b24b3e drm/radeon/kms/atom: Make card_info per device
Make the struct card_info, which is a per struct radeon_device dataset, a
struct member of the radeon device instead of a static per kernel module
value. This should avoid potential problems with two radeon cards installed in
one system.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-10-28 13:34:21 +10:00
Alex Deucher ebbe1cb936 drm/radeon/kms/atom: add support for spread spectrum (v2)
Spread spectrum is a periodic disturbance added
to the feedback divider to change the pixel clock
periodically to reduce interference.

Only enabled on LVDS.

v2: add support for r4xx and fix DCE 3

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-10-26 13:28:22 +10:00
Alex Deucher 0294cf4f7f drm/radeon/kms: fix connector edid handling
Based partly on a patch from
Christian Koenig <deathsimple@vodafone.de>

- fix several memory leaks in radeon_connector->edid handling
- store edid in radeon_connector->edid in detect() or get_modes()
- switch hdmi detect code to use radeon_connector->edid
- add support for oem boards multiple connectors that share
a ddc line.
- short circuit lvds_detect() if have a stored edid

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-10-16 08:46:52 +10:00
Alex Deucher de2103e452 drm/radeon/kms: use drm_mode directly for panel modes
This reduces the number of mode format conversions needed
and makes native panel mode support cleaner.

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-10-12 13:42:48 +10:00
Dave Airlie b8c00ac5b5 drm/fb: add more correct 8/16/24/32 bpp fb support.
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.

this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.

Tested on r100/r600/i945.

Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-10-06 13:54:01 +10:00
Dave Airlie 445282db9e drm/radeon/kms: add initial connector properties
This adds:
coherent mode: TMDS coherent mode for atom cards.
scaling mode: LVDS scaler mode
load detect: DAC load detection, DVI-I, VGA, TV
tmds pll: legacy TMDS pll selection
tv standard: TV standard selection.

for later: other TV ones? dvi subconnector selection using std prop

[contains fixes pointed out on dri-devel for atom bios mixups
 by Michel]

Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-09-18 16:02:00 +10:00
Yang Zhao f657c2a731 drm/radeon: Save and restore bios scratch regs during S/R
[airlied:- adapted slightly in naming]

Signed-off-by: Yang Zhao <yang@yangman.ca>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-09-16 10:21:35 +10:00
Dave Airlie 4ce001abaf drm/radeon/kms: add initial radeon tv-out support.
This ports the tv-out code from the DDX to KMS.

adds a radeon.tv module option, radeon.tv=0 to disable tv

Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-09-08 09:24:37 +10:00
Dave Airlie 785b93ef8c drm/kms: move driver specific fb common code to helper functions (v2)
Initially I always meant this code to be shared, but things
ran away from me before I got to it.

This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.

It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.

radeon retains some specific codes used for a big endian
workaround.

changes:
fix oops in v1
fix freeing path for crtc_info

Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
2009-08-31 09:09:31 +10:00