Impact: cleanup, update to new cpumask API
Irq_desc.affinity and irq_desc.pending_mask are now cpumask_var_t's
so access to them should be using the new cpumask API.
Signed-off-by: Mike Travis <travis@sgi.com>
Provides a small speedup when accessing pefetchable ranges. To indicate
that a memory range is prefetchable, mark it in the dts file with 42000000
instead of 02000000.
A powepc pci_controller is allowed three memory ranges, any of which may be
prefetchable. However, the PCI-PCI bridge configuration space only has one
field for "non-prefetchable memory behind bridge", which has a 32 bit
address, and one field for "prefetchable memory behind bridge", which may
have a 64 bit address. These are PCI bus addresses, not CPU physical
addresses.
So really you're only allowed one memory range of each type. And if you
want the range at a PCI address above 32 bits you must make it
prefetchable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code that sets up the outbound ATMU windows, which is used to map CPU
physical addresses into PCI bus addresses where BARs will be mapped, didn't
work so well.
For one, it leaked the ioremap() of the ATMU registers. Another small bug
was the high 20 bits of the PCI bus address were left as zero. It's legal
for prefetchable memory regions to be above 32 bits, so the high 20 bits
might not be zero.
Mainly, it couldn't handle ranges that were not a power of two in size or
were not naturally aligned. The ATMU windows have these requirements (size
& alignment), but the code didn't bother to check if the ranges it was
programming met them. If they didn't, the windows would silently be
programmed incorrectly.
This new code can handle ranges which are not power of two sized nor
naturally aligned. It simply splits the ranges into multiple valid ATMU
windows. As there are only four windows, pooly aligned or sized ranges
(which didn't even work before) may run out of windows. In this case an
error is printed and an effort is made to disable the unmapped resources.
An improvement that could be made would be to make use of the default
outbound window. Iff hose->pci_mem_offset is zero, then it's possible that
some or all of the ranges might not need an outbound window and could just
use the default window.
The default ATMU window can support a pci_mem_offset less than zero too,
but pci_mem_offset is unsigned. One could say the abilities allowed a
powerpc pci_controller is neither subset nor a superset of the abilities of
a Freescale PCIe controller. Thankfully, the most useful bits are in the
intersection of the two abilities.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Boards should know when QE_USB is used, so that they can configure USB
clocks and pins.
Another option would be to add 'select QE_USB' into USB_GADGET_FSL_QE,
but selects are evil since they don't support dependencies.
While at it, also remove 'host' from the symbol description, since the
QE_USB code is used to support the gadget driver as well.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes following sparse warnings:
CHECK fsl_pci.c
fsl_pci.c:32:13: warning: symbol 'setup_pci_atmu' was not declared. Should it be static?
fsl_pci.c:89:13: warning: symbol 'setup_pci_cmd' was not declared. Should it be static?
fsl_pci.c:133:12: warning: symbol 'fsl_pcie_check_link' was not declared. Should it be static?
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The driver supports very simple GPIO controllers, that is, when a
controller provides just a 'data' register. Such controllers may be
found in various BCSRs (Board's FPGAs used to control board's
switches, LEDs, chip-selects, Ethernet/USB PHY power, etc).
So far we support only 1-byte GPIO banks. Support for other widths may
be implemented when/if needed.
p.s.
To avoid "made up" compatible entries (like compatible = "simple-gpio"),
boards must call simple_gpiochip_init() to pass the compatible string.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this API we're able to set a QE pin to the GPIO mode or a dedicated
peripheral function.
The API relies on the fact that QE gpio controllers are registered. If
they aren't, the API won't work (gracefully though).
There is one caveat though: if anybody occupied the node->data before us,
or overwrote it, then bad things will happen. Luckily this is all in the
platform code that we fully control, so this should never happen.
I could implement more checks (for example we could create a list of
successfully registered QE controllers, and compare the node->data in the
qe_pin_request()), but this is unneeded if nobody is going to do silly
things behind our back.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to not bother with ugly #ifdefs in the drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
powerpc/44x: Support 16K/64K base page sizes on 44x
powerpc: Force memory size to be a multiple of PAGE_SIZE
powerpc/32: Wire up the trampoline code for kdump
powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
powerpc/32: Setup OF properties for kdump
powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
powerpc: Prepare xmon_save_regs for use with kdump
powerpc: Remove default kexec/crash_kernel ops assignments
powerpc: Make default kexec/crash_kernel ops implicit
powerpc: Setup OF properties for ppc32 kexec
powerpc/pseries: Fix cpu hotplug
powerpc: Fix KVM build on ppc440
powerpc/cell: add QPACE as a separate Cell platform
powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
powerpc/mpc5200: fix error paths in PSC UART probe function
powerpc/mpc5200: add rts/cts handling in PSC UART driver
powerpc/mpc5200: Make PSC UART driver update serial errors counters
powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
...
Fix trivial conflict in drivers/char/Makefile as per Paul's directions
This patch adds MDMA/UDMA support using BestComm for DMA on the MPC5200
platform. Based heavily on previous work by Freescale (Bernard Kuhn,
John Rigby) and Domen Puncer.
With this patch, a SanDisk Extreme IV CF card gets read speeds of
approximately 26.70 MB/sec.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When ATA DMA is enabled, bestcomm prefetching does not work. This
patch adds a function to disable bestcomm prefetch when the ATA
Bestcomm task is initialized.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
1) ata.h has dst_pa in the wrong place (needs to match what the BestComm
task microcode in bcom_ata_task.c expects); fix it.
2) The BestComm ATA task priority was changed to maximum in bestcomm_priv.h;
this fixes a deadlock issue experienced with heavy DMA occurring on
both the ATA and Ethernet BestComm tasks, e.g. when downloading a large
file over a LAN to disk.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The buffer descriptors for the ATA BestComm task are larger than the
current definition for bcom_bd. This causes problems because the
various bcom_... functions dereference the buffer descriptor pointer
by using the array operator which doesn't work when the buffer
descriptors are a different size.
This patch adds the bcom_get_bd() function which uses the value in
bcom_task.bd_size to calculate the offset into the BD table. This
patch also changes the definition of bcom_bd to specify a data size
of 0 instead of 1 so that it will never work if anyone attempts to
dereference the bd list as an array (as opposed to something that
might work even though it is wrong).
Finally, this patch moves the definition of bcom_bd up in the file
to eliminate a forward declaration.
Based on patch originally written by Tim Yamin.
Signed-off-by: Tim Yamin <plasm@roo.me.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add const qualifier to device_node argument for
dcr_resource_{start,len} as of_get_property also const-qualifies this
argument.
Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds supports to the "extended" DCR addressing via the indirect
mfdcrx/mtdcrx instructions supported by some 4xx cores (440H6 and
later).
I enabled the feature for now only on AMCC 460 chips.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Does the same for the accompanying MDIO driver, and then modifies the TBI
configuration method. The old way used fields in einfo, which no longer
exists. The new way is to create an MDIO device-tree node for each instance
of gianfar, and create a tbi-handle property to associate ethernet controllers
with the TBI PHYs they are connected to.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are a number of platforms that open code access to
the ppc_pci_flags global variable. However, that variable is not
present if CONFIG_PCI is not set, which can lead to a build break.
This introduces a number of accessor functions that are defined
to be empty in the case of CONFIG_PCI being disabled. The
various platform files in the kernel are updated to use these.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
This adds support for ISA memory holes on the PCI, PCI-X and
PCI-E busses of the 4xx platforms. The patch includes changes
to the Bamboo and Canyonlands device-trees to add such a hole,
others can be updated separately.
The ISA memory hole is an additional outbound window configured
in the bridge to generate PCI cycles in the low memory addresses,
thus allowing to access things such as the hard-decoded VGA
aperture at 0xa0000..0xbffff or other similar things. It's made
accessible to userspace via the new legacy_mem file in sysfs for
which support was added by a previous patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
With this patch we can compile the qe_lib/usb.c without the UCC
support (that is, without UCC_GETH and/or SERIAL_QE).
Fixes following link error (CONFIG_SMP should be =y to trigger this):
arch/powerpc/sysdev/built-in.o: In function `qe_usb_clock_set':
(.text+0x3cae): undefined reference to `cmxgcr_lock'
make: *** [.tmp_vmlinux1] Error 1
While at it, also add missing spinlock.h includes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the CONFIG_SMP case the irq_choose_cpu() code was returning back
a logical cpu id not the physical id. We were writing that directly
into the HW register.
We need to be calling get_hard_smp_processor_id() so irq_choose_cpu()
always returns a physical cpu id.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kexec/kdump currently fails on the IBM QS2x blades when the kexec happens
on a CPU other than the initial boot CPU. It turns out that this is the
result of mpic_init trying to set affinity of each interrupt vector to the
current boot CPU.
As far as I can tell, the same problem is likely to exist on any
secondary MPIC, because they have to deliver interrupts to the first
output all the time. There are two potential solutions for this: either
not set up affinity at all for secondary MPICs, or assume that a single
CPU output is connected to the upstream interrupt controller and hardcode
affinity to that per architecture.
This patch implements the second approach, defaulting to the first output.
Currently, all known secondary MPICs are routed to their upstream port
using the first destination, so we hardcode that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
MPIC has 4 ipis, so it can use the new smp_request_message_ipi to
reduce pathlength when receiving an ipi.
This has the side effect of using the common ipi names, and also
continuing to try request the remaining messages when one fails.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Various printk format string in code used by the Xilinx Virtex platform
are not 32-bit/64-bit safe. Add correct casting to fix the bugs.
Reported-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Without this patch it is possible to select drivers which require
bestcomm support without bestcomm support being selected. This
patch reworks the bestcomm dependencies to ensure the correct
bestcomm tasks are always enabled.
Reported-by: Hans Lehmann <hans.lehmann@ritter-elektronik.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
af_unix: netns: fix problem of return value
IRDA: remove double inclusion of module.h
udp: multicast packets need to check namespace
net: add documentation for skb recycling
key: fix setkey(8) policy set breakage
bpa10x: free sk_buff with kfree_skb
xfrm: do not leak ESRCH to user space
net: Really remove all of LOOPBACK_TSO code.
netfilter: nf_conntrack_proto_gre: switch to register_pernet_gen_subsys()
netns: add register_pernet_gen_subsys/unregister_pernet_gen_subsys
net: delete excess kernel-doc notation
pppoe: Fix socket leak.
gianfar: Don't reset TBI<->SerDes link if it's already up
gianfar: Fix race in TBI/SerDes configuration
at91_ether: request/free GPIO for PHY interrupt
amd8111e: fix dma_free_coherent context
atl1: fix vlan tag regression
SMC91x: delete unused local variable "lp"
myri10ge: fix stop/go mmio ordering
bonding: fix panic when taking bond interface down before removing module
...
The Freescale implementation of MPIC only allows a single CPU destination
for non-IPI interrupts. We add a flag to the mpic_init to distinquish
these variants of MPIC. We pull in the irq_choose_cpu from sparc64 to
select a single CPU as the destination of the interrupt.
This is to deal with the fact that the default smp affinity was
changed by commit 1840475676 ("genirq:
Expose default irq affinity mask (take 3)") to be all CPUs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The init_phy() function attaches to the PHY, then configures the
SerDes<->TBI link (in SGMII mode). The TBI is on the MDIO bus with the PHY
(sort of) and is accessed via the gianfar's MDIO registers, using the
functions gfar_local_mdio_read/write(), which don't do any locking.
The previously attached PHY will start a work-queue on a timer, and
probably an irq handler as well, which will talk to the PHY and thus use
the MDIO bus. This uses phy_read/write(), which have locking, but not
against the gfar_local_mdio versions.
The result is that PHY code will try to use the MDIO bus at the same time
as the SerDes setup code, corrupting the transfers.
Setting up the SerDes before attaching to the PHY will insure that there is
no race between the SerDes code and *our* PHY, but doesn't fix everything.
Typically the PHYs for all gianfar devices are on the same MDIO bus, which
is associated with the first gianfar device. This means that the first
gianfar's SerDes code could corrupt the MDIO transfers for a different
gianfar's PHY.
The lock used by phy_read/write() is contained in the mii_bus structure,
which is pointed to by the PHY. This is difficult to access from the
gianfar drivers, as there is no link between a gianfar device and the
mii_bus which shares the same MDIO registers. As far as the device layer
and drivers are concerned they are two unrelated devices (which happen to
share registers).
Generally all gianfar devices' PHYs will be on the bus associated with the
first gianfar. But this might not be the case, so simply locking the
gianfar's PHY's mii bus might not lock the mii bus that the SerDes setup
code is going to use.
We solve this by having the code that creates the gianfar platform device
look in the device tree for an mdio device that shares the gianfar's
registers. If one is found the ID of its platform device is saved in the
gianfar's platform data.
A new function in the gianfar mii code, gfar_get_miibus(), can use the bus
ID to search through the platform devices for a gianfar_mdio device with
the right ID. The platform device's driver data is the mii_bus structure,
which the SerDes setup code can use to lock the current bus.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
CC: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds support for the GPIO functions of PPC40x and PPC44x
SOCs.
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The fsl_upm nand driver fails to build because fsl_lbc_lock isn't
exported, the lock is needed by the inlined fsl_upm_run_pattern()
function:
ERROR: "fsl_lbc_lock" [drivers/mtd/nand/fsl_upm.ko] undefined!
Dave Jones purposed to export the lock, but it is better to just uninline
the fsl_upm_run_pattern().
When uninlined we also no longer need the exported fsl_lbc_regs, and
both fsl_lbc_lock and fsl_lbc_regs could be marked static.
While at it, also add some missing includes that we should have included
explicitly.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Early versions of the Freescale DIU framebuffer driver depended on a bootmem
allocation of memory for the video buffer. The need for this feature was
removed in commit 6b51d51a, so now we can remove the platform-specific code
that allocated that memory.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Modify mpc83xx_add_bridge to get config space register base address from
the device tree instead of immr + hardcoded offset.
83xx pci nodes have this change:
register properties now contain two address length tuples:
First is the pci bridge register base, this has always been there.
Second is the config base, this is new.
This is documented in dts-bindings/fsl/83xx-512x-pci.txt
The changes accomplish these things:
mpc83xx_add_bridge no longer needs to call get_immrbase
it uses hard coded addresses if the second register value is missing
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifying user-selectable option in the qe_lib/Kconfig was a bad idea
because the qe_lib/Kconfig is included into the top level Kconfig, and
thus the QE_GPIO option appears at the top level menu.
This patch effectively moves the QE_GPIO option under the platform menu
instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is an old workaround in the sysdev/Makefile for dealing
with arch/ppc vs. arch/powerpc compiles. This is no longer
needed as arch/ppc is dead.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch allows the 4xx (conventional) PCI bridge to be disabled
via the device tree. This is needed for 4xx PCI adapter hardware.
Use the PCI node's status property to disable the PCI bridge.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
mpc83xx_wdt is the OF driver now, so we don't need fsl_soc constructor.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The initial patch had the option at the top level which wasn't
quite right. Moving under the platform options is a bit better.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Structured similar to the existing QE GPIO support.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The CPM1 GPIO library code uses the non thread-safe clrbits32/setbits32
macros. This patch protects them with a spinlock.
Based on the CPM2 patch from Laurent Pinchart <laurentp@cse-semaphore.com>,
commit 639d64456e.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's no good reason why a resource_size_t shouldn't just be a
physical address, so simply redefine it in terms of phys_addr_t.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, there are two different fields in the
mv643xx_eth_platform_data struct that together describe the PHY
address -- one field (phy_addr) has the address of the PHY, but if
that address is zero, a second field (force_phy_addr) needs to be
set to distinguish the actual address zero from a zero due to not
having filled in the PHY address explicitly (which should mean
'use the default PHY address').
If we are a bit smarter about the encoding of the phy_addr field,
we can avoid the need for a second field -- this patch does that.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The declaration of total_memory removed. Now including <mm/mmu_decl.h>
instead. Since total_memory is a phys_addr_t which is 64-bit on 44x and
is_power_of_2() works with u32 so I just inlined (size & (size-1)) != 0
instead.
Also this patch fixes default initialization: res->end should be 0x7fffffff
not 0x80000000.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
During recent tests with PCI-E , it has been found the
DRV + De-Emphasis values are not optimum. These new values
are tested thouroughly.
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Feng Kan fkan@amcc.com
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The CPM2 GPIO library code uses the non thread-safe clrbits32/setbits32
macros. This patch protects them with a spinlock.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix two memory leaks in the Freescale QE library: add a missing kfree() in
ucc_fast_init() and ucc_slow_init() if the ioremap() fails, and update
ucc_fast_free() and ucc_slow_free() to call iounmap() if necessary.
Based on a patch from Tony Breeds <tony@bakeyournoodle.com>.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This affects the U3 MSI code as well as the PASEMI MSI code. We keep
some of the MPIC routines as helpers, and also the U3 best-guess
reservation logic. The rest is replaced by the generic code.
And a few printk format changes due to hwirq type change.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is 90% straight forward, although we have to change a few
printk format strings as well because of the change in type of hwirq.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are now two almost identical implementations of an MSI bitmap
allocator, one in mpic_msi.c and the other in fsl_msi.c.
Merge them together and put the result in msi_bitmap.c. Some of the
MPIC bits will remain to provide a nicer interface for the MPIC users.
In the process we fix two buglets. The first is that the allocation
routines, now msi_bitmap_alloc_hwirqs(), returned an unsigned result,
even though they use -1 to indicate allocation failure. Although all
the callers were checking correctly, it is much better for the routine
to just return an int. At least until someone wants > ~2 billion MSIs.
The second buglet is that the device tree reservation logic only
allowed power-of-two reservations. AFAICT that didn't effect any
existing code but it's nicer if we can reserve arbitrary irqs from MSI
use.
We also add some selftests, which exposed the two buglets and now test
for them, as well as some basic sanity tests. The tests are only built
when CONFIG_DEBUG_KERNEL=y.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The FSL MSI code keeps a pointer to the of_node from the device
it represents. However it also has an irq_host, which contains
a pointer to the of_node, so use that one instead.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that arch/ppc is gone and CONFIG_PPC_MERGE is always set, remove
the dead code associated with !CONFIG_PPC_MERGE from arch/powerpc
and include/asm-powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The CPM2 BRG setup functions cpm_setbrg and cpm2_fastbrg don't support
external clocks. This patch adds a new exported __cpm2_setbrg function
that takes the clock rate and clock source as extra parameters, and moves
cpm_setbrg and cpm2_fastbrg to include/asm-powerpc/cpm2.h where they
become inline wrappers around __cpm2_setbrg.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i8259 PIC is disabled on MPC8610HPCD boards, thus currently rtc-cmos
driver fails to probe.
To fix the issue, we lookup the device tree for "chrp,iic" and
"pnpPNP,000" compatible devices, and if not found we do not assign RTC
IRQ and assuming that i8259 was disabled.
Though this patch fixes RTC on some boards (and surely should not break
any other), the whole approach is still broken. We can't easily fix this
though, because old device trees do not specify i8259 interrupts for the
cmos rtc node.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch implement GPIO LIB support for the CPM1 GPIOs.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch implement GPIO LIB support for the CPM2 GPIOs. The code can
also be used for CPM1 GPIO port E, as both cores are compatible at the
register level.
Based on earlier work by Laurent Pinchart.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (34 commits)
powerpc: Wireup new syscalls
Move update_mmu_cache() declaration from tlbflush.h to pgtable.h
powerpc/pseries: Remove kmalloc call in handling writes to lparcfg
powerpc/pseries: Update arch vector to indicate support for CMO
ibmvfc: Add support for collaborative memory overcommit
ibmvscsi: driver enablement for CMO
ibmveth: enable driver for CMO
ibmveth: Automatically enable larger rx buffer pools for larger mtu
powerpc/pseries: Verify CMO memory entitlement updates with virtual I/O
powerpc/pseries: vio bus support for CMO
powerpc/pseries: iommu enablement for CMO
powerpc/pseries: Add CMO paging statistics
powerpc/pseries: Add collaborative memory manager
powerpc/pseries: Utilities to set firmware page state
powerpc/pseries: Enable CMO feature during platform setup
powerpc/pseries: Split retrieval of processor entitlement data into a helper routine
powerpc/pseries: Add memory entitlement capabilities to /proc/ppc64/lparcfg
powerpc/pseries: Split processor entitlement retrieval and gathering to helper routines
powerpc/pseries: Remove extraneous error reporting for hcall failures in lparcfg
powerpc: Fix compile error with binutils 2.15
...
Fixed up conflict in arch/powerpc/platforms/52xx/Kconfig manually.
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To support Cooperative Memory Overcommitment (CMO), we need to check
for failure from some of the tce hcalls.
These changes for the pseries platform affect the powerpc architecture;
patches for the other affected platforms are included in this patch.
pSeries platform IOMMU code changes:
* platform TCE functions must handle H_NOT_ENOUGH_RESOURCES errors and
return an error.
Architecture IOMMU code changes:
* Calls to ppc_md.tce_build need to check return values and return
DMA_MAPPING_ERROR for transient errors.
Architecture changes:
* struct machdep_calls for tce_build*_pSeriesLP functions need to change
to indicate failure.
* all other platforms will need updates to iommu functions to match the new
calling semantics; they will return 0 on success. The other platforms
default configs have been built, but no further testing was performed.
Signed-off-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update iommu_alloc() to take the struct dma_attrs and pass them on to
tce_build(). This change propagates down to the tce_build functions of
all the platforms.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
DDR2 memory DIMMs on the Axon could be accessed only as one partition
when using file system drivers which are using the direct_access() method.
This patch enables for such file system drivers to access Axon's DDR2 memory
even if it is splitted in several partitions.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Axonram module registers one block device for each DDR2 DIMM found
on a system. This means that each DDR2 DIMM becomes its own block device
major number. This patch lets axonram module to register the only one
block device for all DDR2 DIMMs which also spares kernel resources.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Mostly having to do with not marking things __iomem. And some failure
to use appropriate accessors to read MMIO regs.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old code assumed there was only one, but the 8572 actually has 3.
Also, our usual id, 0xe0024520, gets resolved to -1 somewhere, and this was
preventing the multiple buses from having different ids. So we only keep
the low 20 bits, which have the interesting info, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Freescale ships MPC8315E-RDB boards in two variants:
1. With TSEC1 ethernet support and USB UTMI PHY;
2. Without TSEC1 support, but with USB ULPI PHY in addition.
For the second case U-Boot will add status = "disabled"; property
into the TSEC1 node, so Linux should not try to probe it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This allows other platforms with the same pci block like MPC5121 to use it.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Basic PM support for 83xx. Standby is implemented as sleep.
Suspend-to-RAM is implemented as "deep sleep" (with the processor
turned off) on 831x.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the MPC8536 process and MPC8536DS reference board. The
MPC8536 is an e500v2 based SoC which eTSEC, USB, SATA, PCI, and PCIe.
The USB and SATA IP blocks are similiar to those on the PQ2 Pro SoCs and
thus use the same drivers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
udbg_putc is a *function pointer* that is initialized during
udbg_init_cpm. It might not be initialized properly when called from
udbg_putc_cpm(), so (recursively) call udbg_putc_cpm() directly.
Signed-off-by: Nye Liu <nyet@mrv.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix for the following compiler warnings:
CC arch/powerpc/sysdev/bestcomm/bestcomm.o
arch/powerpc/sysdev/bestcomm/bestcomm.c: In function 'mpc52xx_bcom_probe':
arch/powerpc/sysdev/bestcomm/bestcomm.c:446:
warning: format '%08lx' expects type 'long unsigned int',
but argument 2 has type 'phys_addr_t'
CC arch/powerpc/sysdev/bestcomm/sram.o
arch/powerpc/sysdev/bestcomm/sram.c: In function 'bcom_sram_init':
arch/powerpc/sysdev/bestcomm/sram.c:89:
warning: format '%08lx' expects type 'long unsigned int',
but argument 3 has type 'phys_addr_t'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Simplify the interface for setting up bestcomm DMA to PSCs by adding
some helper functions. The helper function sets the correct values
for the initator and ipr values in PSC DMA tasks based on the PSC
number.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Convert i2c-mpc to an of_platform driver. Utilize the code in
drivers/of-i2c.c to make i2c modules dynamically loadable by the
device tree.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This converts ppc to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single().
ppc loses the timeout functionality of smp_call_function_mask() with
this change, as the generic code does not provide that.
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It was discussed that global arch_initcall() is preferred way to probe
QE GPIOs, so let's use it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The 440EPx/GRx chips don't support PCI MRM commands. Drivers determine this
by looking for a zero value in the PCI cache line size register. However,
some drivers write to this register upon initialization. This can cause
MRMs to be used on these chips, which may cause deadlocks on PLB4.
The workaround implemented here introduces a new indirect_type flag, called
PPC_INDIRECT_TYPE_BROKEN_MRM. This is set in the pci_controller structure in
the pci fixup function for 4xx PCI bridges by determining if the bridge is
compatible with 440EPx/GRx. The flag is checked in the indirect_write_config
function, and forces any writes to the PCI_CACHE_LINE_SIZE register to be
zero, which will disable MRMs for these chips.
A similar workaround has been tested by AMCC on various PCI cards, such as
the Silicon Image ATA card and Intel E1000 GIGE card. Hangs were seen with
the Silicon Image card, and MRMs were seen on the bus with a PCI analyzer.
With the workaround in place, the card functioned properly and only Memory
Reads were seen on the bus with the analyzer.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch fixes following section mismatch:
WARNING: arch/powerpc/sysdev/built-in.o(.text+0x11d8): Section mismatch in
reference from the function qe_reset() to the function
.init.text:cpm_muram_init()
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch add a check to the PPC4xx PCIe driver to detect if the port
is disabled via the device-tree. This is needed for the AMCC Canyonlands
board which has an option to either select 2 PCIe ports or 1 PCIe port
and one SATA port. The SATA port and the 1st PCIe port pins are multiplexed
so we can't start both drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is very trivial patch. We're transitioning to the cpm_muram_*
calls. That's it.
Less trivial changes:
- BD_SC_* defines were defined in the cpm.h and qe.h, so to avoid redefines
we remove BD_SC from the qe.h and use cpm.h along with cpm_muram_*
prototypes;
- qe_muram_dump was unused and thus removed;
- added some code to the cpm_common.c to support legacy QE bindings
(data-only node name).
- For convenience, define qe_* calls to cpm_*. So drivers need not to be
changed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is needed to access QE GPIOs via Linux GPIO API.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- split and export __par_io_config_pin() out of par_io_config_pin(), so we
could use the prefixed version with GPIO LIB API;
- rename struct port_regs to qe_pio_regs, and place it into qe.h;
- rename #define NUM_OF_PINS to QE_PIO_PINS, and place it into qe.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a function to the qe_lib to setup QE USB clocks routing.
To setup clocks safely, cmxgcr register needs locking, so I just reused
ucc_lock since it was used only to protect cmxgcr.
The idea behind placing clocks routing functions into the qe_lib is that
later we'll hopefully switch to the generic Linux Clock API, thus, for
example, FHCI driver may be used for QE and CPM chips without nasty #ifdefs.
This patch also fixes QE_USB_RESTART_TX command definition in the qe.h.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
GTM stands for General-purpose Timers Module and able to generate
timer{1,2,3,4} interrupts. These timers are used by the drivers that
need time precise interrupts (like for USB transactions scheduling for
the Freescale USB Host controller as found in some QE and CPM chips),
or these timers could be used as wakeup events from the CPU deep-sleep
mode.
Things unimplemented:
1. Cascaded (32 bit) timers (1-2, 3-4).
This is straightforward to implement when needed, two timers should
be marked as "requested" and configured as appropriate.
2. Super-cascaded (64 bit) timers (1-2-3-4).
This is also straightforward to implement when needed, all timers
should be marked as "requested" and configured as appropriate.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When I changed irq_alloc_host() to take an of_node
(52964f87c64e6c6ea671b5bf3030fb1494090a48: "Add an optional
device_node pointer to the irq_host"), I botched the reference
counting semantics.
Stephen pointed out that it's irq_alloc_host()'s business if
it needs to take an additional reference to the device_node,
the caller shouldn't need to care.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to of_address_to_resource() first, then we don't
need to worry about freeing the irq_host (which the code doesn't do
currently anyway).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If we do the call to of_address_to_resource() first, then we don't
need to worry about freeing the irq_host (which the code doesn't do
currently anyway).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following warning, introduced by commit
475ca391b4 (mpic: Deal with bogus NIRQ
in Feature Reporting Register):
CC arch/powerpc/sysdev/mpic.o
arch/powerpc/sysdev/mpic.c: In function 'mpic_alloc':
arch/powerpc/sysdev/mpic.c:1146: warning: suggest explicit braces to avoid ambiguous 'else'
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Change the name of the device from "rtc-ds1374" to just "ds1374", to match
what all other RTC drivers do. I seem to remember that this name was
chosen to avoid possible confusion with an older ds1374 driver, but that
driver was removed 3 months ago.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, fsl_i2c_of_init() uses the order of the I2C adapter nodes in the
device tree to enumerate the I2C adapters. Instead, let's check for the
cell-index property and use it if it exists.
This is handy for device drivers that need to identify the I2C adapters by
specific numbers. The Freescale MPC8610 ASoC V2 sound drivers are an example.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The i2c_devices[] array in fsl_soc.c lists all the I2C nodes that are supported
on Freescale boards. Add an entry for the Cirrus Logic CS4270 so that a
new-style CS4270 driver will work.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update of_find_i2c_driver in fsl_soc.c to display a warning message if an
I2C node in the device tree isn't found in the i2c_devices[] array.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes few cosmetic issues, also removes unused function,
makes some functions static and reduces #ifdef count.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This MSI driver can be used on 83xx/85xx/86xx board.
In this driver, virtual interrupt host and chip were
setup. There are 256 MSI interrupts in this host, Every 32
MSI interrupts cascaded to one IPIC/MPIC interrupt.
The chip was treated as edge sensitive and some necessary
functions were setup for this chip.
Before using the MSI interrupt, PCI/PCIE device need to
ask for a MSI interrupt in the 256 MSI interrupts. A 256bit
bitmap show which MSI interrupt was used, reserve bit in
the bitmap can be used to force the device use some designate
MSI interrupt in the 256 MSI interrupts. Sometimes this is useful
for testing the all the MSI interrupts. The msi-available-ranges
property in the dts file was used for this purpose.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With the recent DCR code rework, we get a compiler warning about
find_dcr_parent being defined but not used. This fixes it by only defining
the function if CONFIG_PPC_DCR_MMIO is set.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Previously, DCR support was configured at compile time to either use
MMIO or native dcr instructions. Although this works for most
platforms, it fails on FPGA platforms:
1) Systems may include more than one DCR bus.
2) Systems may be native DCR capable and still use memory mapped DCR interface.
This patch provides runtime support based on the device trees for the
case where CONFIG_PPC_DCR_MMIO and CONFIG_PPC_DCR_NATIVE are both
selected. Previously, this was a poorly defined configuration, which
happened to provide NATIVE support. The runtime selection is made
based on the dcr-controller having a 'dcr-access-method' attribute
in the device tree. If only one of the above options is selected,
then the code uses #defines to select only the used code in order to
avoid introducing overhead in existing usage.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Compiling ppc64_defconfig with gcc 4.3 gives thes warnings:
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_get_priority':
arch/powerpc/sysdev/mpic.c:1351: warning: 'is_ipi' may be used uninitialized in this function
arch/powerpc/sysdev/mpic.c: In function 'mpic_irq_set_priority':
arch/powerpc/sysdev/mpic.c:1328: warning: 'is_ipi' may be used uninitialized in this function
It turns out that in the cases where is_ipi is uninitialized, another
variable (mpic) will be NULL and it is dereferenced. Protect against
this by returning if mpic is NULL in mpic_irq_set_priority, and removing
mpic_irq_get_priority completely as it has no in tree callers.
This has the nice side effect of making the warning go away.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some chips (like the SoCs from Freescale) report the wrong value in NIRQ
and this causes issues if its doesn't match or exceed the value of
irq_count.
Add a flag that board code can set to just use irq_count instead of
FRR[NIRQ]. Eventually we'll add a device tree property with the number
of sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds a function to put a 6xx/7xx/7xxx/83xx family CPU into sleep
mode, and return after an interrupt has occurred. It expects to be
called with interrupts disabled, and returns with interrupts disabled.
Interrupts are enabled while the processor is asleep, but the interrupt
that wakes the processor is not handled; it is still pending when this
function returns.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some of the routines defined in mpic_msi.c are declared mpic.h,
so the former should include the latter.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For each mv64360 entry in the OpenFirmware database, add the
registration of an of_bus to take care of devices connected to
the MV64x60 asynchronous devices controller.
This change makes it possible for those devices to be detected by
drivers that support the of_platform without having a custom call
for each of them in the board file.
Signed-off-by: Remi Machet <rmachet@slac.stanford.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
bitmap_find_free_region(), called by mpic_msi_alloc_hwirqs() may return
signed, but hwirq is unsigned. A failed allocation remains unnoticed.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
bitmap_find_free_region(), called by mpic_msi_alloc_hwirqs() may return
signed, but hwirq is unsigned. A failed allocation remains unnoticed.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (23 commits)
[POWERPC] Remove leftover printk in isa-bridge.c
[POWERPC] Remove duplicate #include
[POWERPC] Initialize lockdep earlier
[POWERPC] Document when printk is useable
[POWERPC] Fix bogus paca->_current initialization
[POWERPC] Fix of_i2c include for module compilation
[POWERPC] Make default cputable entries reflect selected CPU family
[POWERPC] spufs: lockdep annotations for spufs_dir_close
[POWERPC] spufs: don't requeue victim contex in find_victim if it's not in spu_run
[POWERPC] 4xx: Fix PCI mem in sequoia DTS
[POWERPC] 4xx: Add endpoint support to 4xx PCIe driver
[POWERPC] 4xx: Fix problem with new TLB storage attibute fields on 440x6 core
[POWERPC] spufs: spu_create should send inotify IM_CREATE event
[POWERPC] spufs: handle faults while the context switch pending flag is set
[POWERPC] spufs: fix concurrent delivery of class 0 & 1 exceptions
[POWERPC] spufs: try to route SPU interrupts to local node
[POWERPC] spufs: set SPU_CONTEXT_SWITCH_PENDING before synchronising SPU irqs
[POWERPC] spufs: don't acquire state_mutex interruptible while performing callback
[POWERPC] spufs: update master runcntl with context lock held
[POWERPC] spufs: fix post-stopped update of MFC_CNTL register
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (32 commits)
net: Added ASSERT_RTNL() to dev_open() and dev_close().
can: Fix can_send() handling on dev_queue_xmit() failures
netns: Fix arbitrary net_device-s corruptions on net_ns stop.
netfilter: Kconfig: default DCCP/SCTP conntrack support to the protocol config values
netfilter: nf_conntrack_sip: restrict RTP expect flushing on error to last request
macvlan: Fix memleak on device removal/crash on module removal
net/ipv4: correct RFC 1122 section reference in comment
tcp FRTO: SACK variant is errorneously used with NewReno
e1000e: don't return half-read eeprom on error
ucc_geth: Don't use RX clock as TX clock.
cxgb3: Use CAP_SYS_RAWIO for firmware
pcnet32: delete non NAPI code from driver.
fs_enet: Fix a memory leak in fs_enet_mdio_probe
[netdrvr] eexpress: IPv6 fails - multicast problems
3c59x: use netstats in net_device structure
3c980-TX needs EXTRA_PREAMBLE
fix warning in drivers/net/appletalk/cops.c
e1000e: Add support for BM PHYs on ICH9
uli526x: fix endianness issues in the setup frame
uli526x: initialize the hardware prior to requesting interrupts
...
This patch adds basic endpoint support to the 4xx PCIe driver.
This is done by checking the device_type property of the PCIe
device node ("pci" for root-complex and "pci-endpoint" for endpoint
configuration).
Note: Currently we map a fixed 64MByte window to PLB address 0 (SDRAM).
This should probably be configurable via a dts property.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
arch/powerpc/sysdev/xilinx_intc.c: In function 'xilinx_intc_init':
arch/powerpc/sysdev/xilinx_intc.c:111: warning: format '%08X' expects type 'unsigned int', but argument 2 has type 'resource_size_t'
drivers/char/xilinx_hwicap/xilinx_hwicap.c: In function 'hwicap_setup':
drivers/char/xilinx_hwicap/xilinx_hwicap.c:626: warning: cast to pointer from integer of different size
drivers/char/xilinx_hwicap/xilinx_hwicap.c:646: warning: format '%x' expects type 'unsigned int', but argument 6 has type 'resource_size_t'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When resource_size_t is larger than an int, the current code
generates a build warning. Kill it.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix current (-git16) missing docbook/kernel-doc notation in RapidIO files.
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'sys_size'
Warning(linux-2.6.25-git16//include/linux/rio.h:187): No description found for parameter 'phy_type'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:188): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:224): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:245): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:270): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:311): No description found for parameter 'mport'
Warning(linux-2.6.25-git16//arch/powerpc/sysdev/fsl_rio.c:996): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Change RapidIO doorbell source and target ID field to 16-bit for
support large system size, which max rio devid is 65535.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RapidIO system size will auto probe in RIO setup. The route table
and rionet_active in rionet.c are changed to be allocated dynamically
according to the size of the system.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This initializes the RapidIO controller driver using addresses and
interrupt numbers obtained from the firmware device tree, rather than
using hardcoded constants.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The original RapidIO driver suppose there is only one mpc85xx RIO controller
in system. So, some data structures are defined as mpc85xx_rio global, such
as 'regs_win', 'dbell_ring', 'msg_tx_ring'. Now, I changed them to mport's
private members. And you can define multi RIO OF-nodes in dts file for multi
RapidIO controller in one processor, such as PCI/PCI-Ex host controllers in
Freescale's silicon. And the mport operation function declaration should be
changed to know which RapidIO controller is target.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The driver is suitable for the Freescale MPC8641 processor as well as
85xx processors, so this changes the mpc85xx prefix to fsl.
Signed-off-by: Zhang Wei <wei.zhang@freescale.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move mv643xx_eth's static state (ethernet register block base address
and MII management interface spinlock) into a struct hanging off the
shared platform device. This is necessary to support chips that
contain multiple mv643xx_eth silicon blocks.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Add platform code to support Freescale DIU. The platform code includes
framebuffer memory allocation, pixel format, monitor port, etc.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alter the block device ->direct_access() API to work with the new
get_xip_mem() API (that requires both kaddr and pfn are returned).
Some architectures will not do the right thing in their virt_to_page() for use
by XIP (to translate from the kernel virtual address returned by
direct_access(), to a user mappable pfn in XIP's page fault handler.
However, we can't switch it to just return the pfn and not the kaddr, because
we have no good way to get a kva from a pfn, and XIP requires the kva for its
read(2) and write(2) handlers. So we have to return both.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Carsten Otte <cotte@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-mm@kvack.org
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The MPSC driver and prpmc2800.dts have been modified to use property
'cell-index' as the serial port number, but the early serial console
driver for the mv64x60 has not been modified to use this new property.
This fixes it.
Signed-off-by: Remi Machet (rmachet@slac.stanford.edu)
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If one of the devices of the mv64x60 init fails, the remaining
devices are not initialized.
This changes the code to display an error and continue the
initialization.
Signed-off-by: Remi Machet (rmachet@slac.stanford.edu)
Signed-off-by: Paul Mackerras <paulus@samba.org>
I2C parameters freq_m and freq_n are assigned defaults in the code,
but if properties for those parameters are not found in the open
firmware description the init routine returns an error and doesn't
create the platform device.
This changes the code so that it doesn't return an error if the
properties are not found but instead uses the default values.
Signed-off-by: Remi Machet (rmachet@slac.stanford.edu)
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (202 commits)
[POWERPC] Fix compile breakage for 64-bit UP configs
[POWERPC] Define copy_siginfo_from_user32
[POWERPC] Add compat handler for PTRACE_GETSIGINFO
[POWERPC] i2c: Fix build breakage introduced by OF helpers
[POWERPC] Optimize fls64() on 64-bit processors
[POWERPC] irqtrace support for 64-bit powerpc
[POWERPC] Stacktrace support for lockdep
[POWERPC] Move stackframe definitions to common header
[POWERPC] Fix device-tree locking vs. interrupts
[POWERPC] Make pci_bus_to_host()'s struct pci_bus * argument const
[POWERPC] Remove unused __max_memory variable
[POWERPC] Simplify xics direct/lpar irq_host setup
[POWERPC] Use pseries_setup_i8259_cascade() in pseries_mpic_init_IRQ()
[POWERPC] Turn xics_setup_8259_cascade() into a generic pseries_setup_i8259_cascade()
[POWERPC] Move xics_setup_8259_cascade() into platforms/pseries/setup.c
[POWERPC] Use asm-generic/bitops/find.h in bitops.h
[POWERPC] 83xx: mpc8315 - fix USB UTMI Host setup
[POWERPC] 85xx: Fix the size of qe muram for MPC8568E
[POWERPC] 86xx: mpc86xx_hpcn - Temporarily accept old dts node identifier.
[POWERPC] 86xx: mark functions static, other minor cleanups
...
The kconfig entry can go away once arch/ppc and references to the config in
drivers are removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
qe_get_brg_clk() will be used by the fsl_gtm routines.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
qe_muram_offset is the reverse of the qe_muram_addr, will be
used for the Freescale QE USB Host Controller driver.
This patch also moves qe_muram_addr into the qe.h header, plus
adds __iomem hints to use with sparse.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Freescale UPM can be used to adjust localbus timings or to generate
orbitrary, pre-programmed "patterns" on the external Localbus signals.
This patch implements few routines so drivers could work with UPMs in
safe and generic manner.
So far there is just one user of these routines: Freescale UPM NAND
driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Similarly to what is done for PQ1-based platforms, this patch resets the
PQ2 Communication Processor Module in cpm2_reset() when early debugging is
not enabled. This helps avoiding conflicts when the boot loader configured
the CPM in an unexpected way.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Having the id field be an int was making more complex bus topologies
excessively difficult. For now, just convert it to a string, and
change all instances of "bus->id = val" to
snprintf(id, MII_BUS_ID_LEN, "%x", val).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The mv643xx_eth driver is being modified to support multiple instances
of the ethernet silicon block on the same platform. Each block contains
a single register bank containing the registers for up to three ports
interleaved within that bank. This patch updates the PowerPC OF to
platform_device glue code to support multiple silicon blocks, each
with up to three ethernet ports. The main difference is that we now
allow multiple mv64x60_shared platform_devices to be registered and
we provide each port platform_device with a pointer to its associated
shared platform_device. The pointer will not be used until the
mv643xx_eth driver changes are committed.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Mark Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove several unused (or software config only) properties.
Rename marvel node to "system-controller". Also, rename the
"block-index" property to "cell-index" to conform to current
practice.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Compatible names should refer to a specific version of the hardware,
without wildcards. Change each instance of mv64x60 to mv64360, which
is the oldest version we currently support.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We really need to ack interrupts at mpic_teardown, since
not all platforms reset mpic at kernel start-up. For example,
kexec'ed kernel hangs on P.A. Semi if mpic_eoi() isn't called.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A missing break statement in a switch caused cpm2_clk_setup() to initialize
SCC2 instead of SCC1.
Signed-off-by: Laurent Pinchart <laurentp@cse-semaphore.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch creates a common system reset routine for all 40x and 44x
systems. Previously only a 44x routine existed. But since this system
reset via the debug control register is common for 40x and 44x let's
share this code for all those platforms in ppc4xx_soc.c.
This patch also enables CONFIG_4xx_SOC for all 40x and 44x platforms.
Tested on Kilauea (405EX) and Canyonlands (440EX).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The patch fixes a bug, where the PESDRn_UTLSET1 register was setup
wrongly resulting in a non working PCIe port 1. With this fix both
PCIe ports work fine again.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the arch/powerpc PCI subsystem now does a complete re-assignment of
the resources, we can move from the unconditional PCIe PHY reset to the
conditional version. Now the PHY is only reset, if no link is established yet.
An additional PHY reset (one is already done in U-Boot) leads to problems
with some Atheros PCIe boards and some HP FPGA PCIe designs.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for the 256k L2 cache found on some IBM/AMCC
4xx PPC's. It introduces a common 4xx SoC file (sysdev/ppc4xx_soc.c)
which currently "only" adds the L2 cache init code. Other common 4xx
stuff can be added later here.
The L2 cache handling code is a copy of Eugene's code in arch/ppc
with small modifications.
Tested on AMCC Taishan 440GX.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
All this code is needed to properly initialize the 460EX PCIe host
bridge(s). We re-initialize all ports again, even though this has been done
in the bootloader (U-Boot) before. This way we make sure, that we always
run the latest init code in Linux and don't depend on code versions from
U-Boot.
Unfortunately all IBM/AMCC chips currently supported in this PCIe driver need
a different reset-/init-sequence.
Tested on AMCC Canyonlands eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The "bestcomm-core" driver defines its of_match table as follows
static struct of_device_id mpc52xx_bcom_of_match[] = {
{ .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", },
{ .type = "dma-controller", .compatible = "mpc5200-bestcomm", },
{},
};
so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property. Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.
Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.
This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the bestcomm initialization fails, calls to the task allocate
function should fail gracefully instead of oopsing with a NULL deref.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller. init_ipic_sysfs() will crash in that case.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The function was returning NULL the second time it was
called if the firmware was uploaded from the boot loader
or the first time it was called if the firmware was
uploaded from the kernel.
Signed-off-by: Ionut Nicu <ionut.nicu@freescale.com>
Acked-By: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix a typo in qe_upload_firmware() that prevented uploading firmware on
systems with more than one RISC core.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I was running sparse on something else and noticed sparse warnings
and especially the bogus code that is fixed by the first hunk of
this patch, so I fixed them all while at it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Milton Miller <miltonm@bga.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove warning:
arch/powerpc/sysdev/mpic_pasemi_msi.c: In function 'pasemi_msi_setup_msi_irqs':
arch/powerpc/sysdev/mpic_pasemi_msi.c:135: warning: 'addr' is used uninitialized in this function
Turns out addr wasn't even used, it's a leftover from the u3msi code.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The functions of_find_compatible_node and of_find_node_by_type both
call of_node_get on their result. So any error handling code
thereafter should call of_node_put(np). This is taken care of in the
case where there is a goto out, but not when there is a direct return.
The function irq_alloc_host puts np into the returned structure, which is
stored in the global variable mpc8xx_pic_host, so the reference count
should be set for the lifetime of that variable. The current solution ups
the reference count again in the argument to irq_alloc_host so that it can
be decremented on the way out. This seems a bit unnecessary, and also
doesn't work in the case where irq_alloc_host fails, because then the
reference count only goes does by one, whereas it should go down by two. A
better solution is to not increment the reference count in the argument to
irq_alloc_host and only decrement it on the way out in an error case.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = \(of_get_parent\|of_find_compatible_node\)(...);
if (E == NULL) S
... when != of_node_put(...,(T1)E,...)
when != if (E != NULL) { ... of_node_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != of_node_put(...,(T2)E,...)
when != if (E != NULL) { ... of_node_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
One is intoduced by me (of_node_put() absence) and another was
present already (not checking for NULL).
Found by Stephen Rothwell.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is used on the mpc8315 SoC for TDM DMA error interrupts.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also:
- rename "fsl_spi" to "fsl,spi";
- add and use cell-index property, if found;
- split probing code out of fsl_spi_init, thus we can call
it for legacy device_type probing and new "compatible" probing.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In case of QE we can use brg-frequency (which is qeclk/2).
Thus no need to divide sysclk in the spi_mpc83xx.
This patch also adds code to use get_brgfreq() on QE chips.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now we're searching for "fsl,qe", "fsl,qe-muram", "fsl,qe-muram-data"
and "fsl,qe-ic".
Unfortunately it's still impossible to remove device_type = "qe"
from the existing device trees because older u-boots are looking for it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rename commproc.[ch] to cpm1.[ch] to be more consistent with cpm2. Also
rename cpm2_common.c to cpm2.c as suggested by Scott Wood. Adjust the
includes accordingly.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move cpm1 specific prototypes to asm/commproc.h and mpc8xx specific
prototypes to asm/mpc8xx.h. Adjust includes accordingly. Remove now
unneeded sysdev/commproc.h.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m8xx_pic_init calls both mpc8xx_pic_init and cpm_pic_init. Renaming the
function to use the same name space as the rest of the mpc8xx
specific funtions and to be more meaningful.
m8xx_pic_init is declared in ppc8xx_pic.h but defined nowhere in the ppc
tree. Remove it.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
m8xx_cpm_hostalloc is still defined in commproc.c, but no users are left
in the kernel tree. m8xx_cpm_hostfree and m8xx_cpm_hostdump are only
defined in the headers. Remove this dead code.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I2C adapter drivers are supposed to handle retries on nack by themselves
if they do, so there's no point in setting .retries if they don't.
As this retry mechanism is going away (at least in its current form),
clean this up now so that we don't get build failures later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Mark A. Greer <mgreer@mvista.com>
This patch extends the Ebony and Walnut platform code to instantiate
the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip
found on both those boards. The patch uses a helper function to scan
the device tree and instantiate the appropriate platform_device based
on it, so it should be easy to extend for other boards which have mmio
mapped RTC chips.
Along with this, the device tree binding for the ds1743 chips is
tweaked, based on the existing DS1385 OF binding found at:
http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt
Although that document covers the NVRAM portion of the chip, whereas
here we're interested in the RTC portion, so it's not entirely clear
if that's a good model.
This implements only RTC class driver support - that is /dev/rtc0, not
/dev/rtc, and the low-level get/set time callbacks remain
unimplemented. That means in order to get at the clock you will
either need a modified version of hwclock which will look at
/dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
All kobjects require a dynamically allocated name now. We no longer
need to keep track if the name is statically assigned, we can just
unconditionally free() all kobject names on cleanup.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Do just enough to move the RapidIO support code for 85xx over from arch/ppc
into arch/powerpc and make it still build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Don't depend on the reg property as a way to determine the base
of the immr space. The reg property might be defined differently for
different SoC families.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
IPIC is not just for 83xx anymore so make it a separate config option.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added ipic_info entries for vectors used by 512x that
were previously unused by 83xx.
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for UART serial ports using a Freescale QUICCEngine. Update
booting-without-of.txt to define new properties for a QE UART node. Update
the MPC8323E-MDS device tree to add UCC5 as a UART. Update the QE library
to support slow UCC devices and modules.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Define the layout of a binary blob that contains a QE firmware and instructions
on how to upload it. Add function qe_upload_firmware() to parse the blob
and perform the actual upload. Fully define 'struct rsp' in immap_qe.h to
include the actual RISC Special Registers. Added description of a new
QE firmware node to booting-without-of.txt.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fixed-link says: register new "Fixed/emulated PHY", i.e. PHY that
not connected to the real MDIO bus.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove device_type = "usb" for 83xx SoC USB controller
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpic_map() and __mpic_map_mmio() need to use phys_addr_t for the
physical address they are passed.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current PCI code for Freescale 85xx/86xx was treating the virtual
P2P PCIe bridge as a transparent bridge. Rather than doing that fixup
the virtual P2P bridge by copying the resources from the PHB.
Also, fixup a bit of the code for dealing with resource_size_t being
64-bits and how we set ATMU registers for >4G.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These values now match what is generated by the uboot BSP generator.
Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Because of how big mapping the config space is (1M per bus), we limit how
many busses we support for now. In the long run, we could replace that
with something akin to kmap_atomic instead.
This patch changes the limit from currently 16 to 64.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
By default the OpenPIC on PWRficient will bias to one core (since that
will improve changes of the other core being able to stay idle/powered
down). However, this conflicts with most irq load balancing schemes,
since setting an interrupt to be delivered to either core doesn't really
result in the load being shared. It also doesn't work well with the
soft irq disable feature of PPC, since EE will stay on until the first
interrupt is taken while soft disabled.
Set the gconf0 config bit that enables even distribution of interrupts
among the two cores.
Signed-off-by: Olof Johansson <olof@lixom.net>
Some PWRficient-based boards have a NMI button that's wired up to a GPIO
as interrupt source. By configuring the openpic accordingly, these get
delivered as a machine check with high priority, instead of as an external
interrupt.
The device tree contains a property "nmi-source" in the openpic node
for these systems, and it's the (hwirq) source for the input.
Also, for these interrupts, the IACK is read from another register than
the regular (MCACK instead), but they are EOI'd as usual. So implement
said function for the mpic driver.
Finally, move a couple of external function defines to include/ instead
of local under sysdev. Being able to mask/unmask and eoi directly saves
us from setting up a dummy irq handler that will never be called.
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch sets the ibpre flag (Inbound Presence) for the 405EX
in the 4xx PCIe driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a UIC cascade handler rework to use set_irq_chained_handler() for
cascade, just like othe ppc platforms do. With current implementation we have
additional redirection for irq handler and we call generic_handle_irq twice
(once for the primary uic and the other time for handling cascade interrupt).
This causes Ingo's realtime support patch to stop working on 4xx.
Not sure of any other possible problems though, but with
set_irq_chained_handler() we can abolish "struct irqaction cascade" from the
chip descriptor and call generic_handle_irq() once, directly for cascade irq.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch makes PowerPC 4xx UIC use generic level irq handler instead
of a custom handle_uic_irq() function. We ack only edge irqs in mask_ack
callback, since acking a level irq on UIC has no effect if the interrupt
is still asserted by the device, even if the interrupt is already masked.
So, to really de-assert the interrupt we need to de-assert the external
source first *and* ack it on UIC then. The handle_level_irq() function
masks and ack's the interrupt with mask_ack callback prior to calling
the actual ISR and unmasks it at the end. So, to use it with UIC interrupts
we need to ack level irqs in the unmask callback instead, after the ISR
has de-asserted the external interrupt source. Even if we ack the interrupt
that we didn't handle (unmask/ack it at the end of the handler, while
next irq is already pending) it will not de-assert the irq, untill we
de-assert its exteral source.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds runtime detection of the 440SPe revision A chips. These
chips are equipped with a slighly different PCIe core and need special/
different initialization. The compatible node is changed to
"plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that
can be equipped with both PPC revisions like the AMCC Yucca.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This improves the way the 4xx PCI-E code handles checking for a link
and adds explicit testing of CRS result codes on config space accesses.
This should make it more reliable.
Also, bridges with no link are now still created, though config space
accesses beyond the root complex are filtered. This is one step toward
eventually supporting hotplug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous 2 patches the support for the 4xx PCI Express
cells as found in the 440SPe revA, revB and 405EX.
Unfortunately, due to significant differences between these, and other
interesting "features" of those pieces of HW, the code isn't as simple
as it is for PCI and PCI-X and some of the functions differ significantly
between the 3 implementations. Thus, not only this code can only support
those 3 implementations for now and will refuse to operate on any other,
but there are added ifdef's to avoid the bloat of building a fairly large
amount of code on platforms that don't need it.
Also, this code currently only supports fully initializing root complex
nodes, not endpoint. Some more code will have to be lifted from the
arch/ppc implementation to add the endpoint support, though it's mostly
differences in memory mapping, and the question on how to represent
endpoint mode PCI in the device-tree is thus open.
Many thanks to Stefan Roese for testing & fixing up the 405EX bits !
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the previous patch the support for the 4xx PCI 2.x
bridges.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds base support code for the 4xx PCI-X bridge. It also provides
placeholders for the PCI and PCI-E version but they aren't supported
with this patch.
The bridges are configured based on device-tree properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.
This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:
* The source is calculated as 512 + the value written into the MSI
register
* The vector for this source is added to the source and reported
through IACK
This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.
Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.
If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.
Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC " to "PASEMI-OPIC".
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Optimize MPIC IPIs, by passing in the IPI number as the argument to the
handler, since all we did was translate it back based on which mpic
the interrupt came though on (and that was always the primary mpic).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add function qe_clock_source() which takes a string containing the name of a
QE clock source (as is typically found in device trees) and returns the
matching enum qe_clock value.
Update booting-without-of.txt to indicate that the UCC properties rx-clock
and tx-clock are deprecated and replaced with rx-clock-name and tx-clock-name,
which use strings instead of numbers to indicate QE clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch moves the CPM command handling into commproc.c
for CPM1 and cpm2_common.c. This is yet another preparation
to get rid of drivers accessing the CPM via the global cpmp.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
PORTA and PORTB have odr registers, as well. However, the PORTB odr
register is only 16bit.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Only external interrupts in edge detect mode support ack operation.
Therefore, in most cases ack is not needed. The patch makes ipic
ack only when it's needed. This could boost over all system performance.
Signed-off-by: Li Yang <leoli@freescale.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Removed address fields in ethernet nodes
* Removed #address-cells, #size-cells from gianfar nodes
* Added cell-index to gianfar and ucc ethernet nodes
* Added enet[0..3] labels
* Renamed compatible node for gianfar mdio to "fsl,gianfar-mdio"
* Removed device_type = "mdio"
The matching for gianfar mdio still supports the old "mdio"/"gianfar" combo
but it is now considered deprecated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
qe_setbrg() currently takes an integer to indicate the BRG number. Change that
to take an enum qe_clock instead, since this enum is intended to represent
clock sources.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These interrupts are introduced by the latest Freescale SoC
such as MPC837x.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Convert #include of asm/of_{platform, device}.h into
linux/of_{platform,device}.h for remaining arch/powerpc files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds uic_mask_ack_irq() callback to PowerPC 4xx uic code
to avoid kernel crash. It is used for edge-triggered interrupts
by handle_uic_irq().
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
A debugging printk is removed, and a comment is fixed to match
the code.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 91a69029 introduced an additional parameter to the .read and .write
methods for sysfs binary attributes. Two mv64x60_pci functions
were missed in that patch, resulting in these errors:
/cache/git/linux-2.6/arch/powerpc/sysdev/mv64x60_pci.c:77: warning: initialization from incompatible pointer type
/cache/git/linux-2.6/arch/powerpc/sysdev/mv64x60_pci.c:78: warning: initialization from incompatible pointer type
Add the missing "struct bin_attribute *" parameter.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since commit 76d2160147, the NE2000 card
is not working anymore on PPC and POWERPC and produces WATCHDOG
timeouts.
The patch below fixes that the same way it has been done on x86, x86_64
and MIPS.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is the microcode for the GenBD task and the associated
support code. This is a generic task that copy data to/from
a hardware FIFO. This is currently locked to 32bits wide
access but could be extended as needed.
The microcode itself comes directly from the offical
API (v2.2)
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is the microcode for the FEC task and the associated
support code.
The microcode itself comes directly from the offical
API (v2.2)
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This is the microcode for the ATA task and the associated
support code.
The microcode itself comes directly from the offical
API (v2.2)
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for the core of the BestComm API
for the Freescale MPC5200(b). The BestComm engine is a
microcode-controlled / tasks-based DMA used by several
of the onchip devices.
Setting up the tasks / memory allocation and all common
low level functions are handled by this patch.
The specifics details of each tasks and their microcode
are split-out in separate patches.
This is not the official API, but a much cleaner one.
(hopefully)
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Mike Travis