A peer (or local user) may cause TCP to use a nominal MSS of as little
as 88 (actual MSS of 76 with timestamps). Given that we have a
sufficiently prodigious local sender and the peer ACKs quickly enough,
it is nevertheless possible to grow the window for such a connection
to the point that we will try to send just under 64K at once. This
results in a single skb that expands to 861 segments.
In some drivers with TSO support, such an skb will require hundreds of
DMA descriptors; a substantial fraction of a TX ring or even more than
a full ring. The TX queue selected for the skb may stall and trigger
the TX watchdog repeatedly (since the problem skb will be retried
after the TX reset). This particularly affects sfc, for which the
issue is designated as CVE-2012-3412.
Therefore:
1. Add the field net_device::gso_max_segs holding the device-specific
limit.
2. In netif_skb_features(), if the number of segments is too high then
mask out GSO features to force fall back to software GSO.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mesh path timer needs to be canceled when
leaving the mesh as otherwise it could fire
after the interface has been removed already.
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a corner case that can happen when we
suspend with a timer running, then resume and
disconnect. If we connect again, suspend and
resume we might start timers that shouldn't be
running. Reset the timer flags to avoid this.
This affects both mesh and managed modes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull second vfs pile from Al Viro:
"The stuff in there: fsfreeze deadlock fixes by Jan (essentially, the
deadlock reproduced by xfstests 068), symlink and hardlink restriction
patches, plus assorted cleanups and fixes.
Note that another fsfreeze deadlock (emergency thaw one) is *not*
dealt with - the series by Fernando conflicts a lot with Jan's, breaks
userland ABI (FIFREEZE semantics gets changed) and trades the deadlock
for massive vfsmount leak; this is going to be handled next cycle.
There probably will be another pull request, but that stuff won't be
in it."
Fix up trivial conflicts due to unrelated changes next to each other in
drivers/{staging/gdm72xx/usb_boot.c, usb/gadget/storage_common.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (54 commits)
delousing target_core_file a bit
Documentation: Correct s_umount state for freeze_fs/unfreeze_fs
fs: Remove old freezing mechanism
ext2: Implement freezing
btrfs: Convert to new freezing mechanism
nilfs2: Convert to new freezing mechanism
ntfs: Convert to new freezing mechanism
fuse: Convert to new freezing mechanism
gfs2: Convert to new freezing mechanism
ocfs2: Convert to new freezing mechanism
xfs: Convert to new freezing code
ext4: Convert to new freezing mechanism
fs: Protect write paths by sb_start_write - sb_end_write
fs: Skip atime update on frozen filesystem
fs: Add freezing handling to mnt_want_write() / mnt_drop_write()
fs: Improve filesystem freezing handling
switch the protection of percpu_counter list to spinlock
nfsd: Push mnt_want_write() outside of i_mutex
btrfs: Push mnt_want_write() outside of i_mutex
fat: Push mnt_want_write() outside of i_mutex
...
Merge Andrew's second set of patches:
- MM
- a few random fixes
- a couple of RTC leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (120 commits)
rtc/rtc-88pm80x: remove unneed devm_kfree
rtc/rtc-88pm80x: assign ret only when rtc_register_driver fails
mm: hugetlbfs: close race during teardown of hugetlbfs shared page tables
tmpfs: distribute interleave better across nodes
mm: remove redundant initialization
mm: warn if pg_data_t isn't initialized with zero
mips: zero out pg_data_t when it's allocated
memcg: gix memory accounting scalability in shrink_page_list
mm/sparse: remove index_init_lock
mm/sparse: more checks on mem_section number
mm/sparse: optimize sparse_index_alloc
memcg: add mem_cgroup_from_css() helper
memcg: further prevent OOM with too many dirty pages
memcg: prevent OOM with too many dirty pages
mm: mmu_notifier: fix freed page still mapped in secondary MMU
mm: memcg: only check anon swapin page charges for swap cache
mm: memcg: only check swap cache pages for repeated charging
mm: memcg: split swapin charge function into private and public part
mm: memcg: remove needless !mm fixup to init_mm when charging
mm: memcg: remove unneeded shmem charge type
...
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Features include:
- Patches from Bryan to allow splitting of the NFSv2/v3/v4 code into
separate modules.
- Fix Oopses in the NFSv4 idmapper
- Fix a deadlock whereby rpciod tries to allocate a new socket and
ends up recursing into the NFS code due to memory reclaim.
- Increase the number of permitted callback connections.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQGF+vAAoJEGcL54qWCgDy6ncP/jKVl/Yjz6i1b/8QtC0EmYFb
XNwbjZicNupVM98XPLm+sfdWxvoGiHSMbwG8t/hx5Z6CteM18adeGNO1KqP9xQyg
scPvFmqj5VJNHsHztcHIFHFYdpsuJqRKcW3TA2l8AkNOm6uBcnXArRosYN6LrXik
hI/jWcyv8wZuooSQrLf463JK37t/s6LuUQo6jKP4582sbANHvPdLkHFCYg3yt1Sk
2IIo2CLLs2cJUswGJnsHT76Jxfvh21NdGtvydjVjpr4H0/LY5GykBc23AAL9TWj6
KlegDO902hLzEE93xazF59hQZrPuwBi3quEMJ3X0mjdNQWb4G96s/t2hmwpTjWyc
mjpRsuaGlCXDxcrI5dnU52hqKa0Ju1ipbLpghxSVfilRy998xvGp5Yc6ADU+pYnt
uP09lamCyjFEa+gDSqGt7lv4dFmdPJjWZdkXLPv0ah5sXVMYAT8NRLUfiE1+hLLu
zKaM84PHSEvykFeJ2WvjDTgF3L55y3x6L3LN4UkKmfO5nqQf7csPcquU1NfHh25S
jjKGq2SKGoYG1l6FwK3hemup5cnFUEX78E2QeLrmaHg92fJDGrz587i6MPc5jrSe
sOSX/CpuCJd4VhodIo8T00me0GZSHEU7RP2KEc518ZvrPmz13avXeLeG9nYhjuxM
cV9Ex8zh2Y4aiUXCy3uA
=KSix
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.6-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull second wave of NFS client updates from Trond Myklebust:
- Patches from Bryan to allow splitting of the NFSv2/v3/v4 code into
separate modules.
- Fix Oopses in the NFSv4 idmapper
- Fix a deadlock whereby rpciod tries to allocate a new socket and ends
up recursing into the NFS code due to memory reclaim.
- Increase the number of permitted callback connections.
* tag 'nfs-for-3.6-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
nfs: explicitly reject LOCK_MAND flock() requests
nfs: increase number of permitted callback connections.
SUNRPC: return negative value in case rpcbind client creation error
NFS: Convert v4 into a module
NFS: Convert v3 into a module
NFS: Convert v2 into a module
NFS: Keep module parameters in the generic NFS client
NFS: Split out remaining NFS v4 inode functions
NFS: Pass super operations and xattr handlers in the nfs_subversion
NFS: Only initialize the ACL client in the v3 case
NFS: Create a try_mount rpc op
NFS: Remove the NFS v4 xdev mount function
NFS: Add version registering framework
NFS: Fix a number of bugs in the idmapper
nfs: skip commit in releasepage if we're freeing memory for fs-related reasons
sunrpc: clarify comments on rpc_make_runnable
pnfsblock: bail out partial page IO
Pull networking update from David S. Miller:
"I think Eric Dumazet and I have dealt with all of the known routing
cache removal fallout. Some other minor fixes all around.
1) Fix RCU of cached routes, particular of output routes which require
liberation via call_rcu() instead of call_rcu_bh(). From Eric
Dumazet.
2) Make sure we purge net device references in cached routes properly.
3) TG3 driver bug fixes from Michael Chan.
4) Fix reported 'expires' value in ipv6 routes, from Li Wei.
5) TUN driver ioctl leaks kernel bytes to userspace, from Mathias
Krause."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (22 commits)
ipv4: Properly purge netdev references on uncached routes.
ipv4: Cache routes in nexthop exception entries.
ipv4: percpu nh_rth_output cache
ipv4: Restore old dst_free() behavior.
bridge: make port attributes const
ipv4: remove rt_cache_rebuild_count
net: ipv4: fix RCU races on dst refcounts
net: TCP early demux cleanup
tun: Fix formatting.
net/tun: fix ioctl() based info leaks
tg3: Update version to 3.124
tg3: Fix race condition in tg3_get_stats64()
tg3: Add New 5719 Read DMA workaround
tg3: Fix Read DMA workaround for 5719 A0.
tg3: Request APE_LOCK_PHY before PHY access
ipv6: fix incorrect route 'expires' value passed to userspace
mISDN: Bugfix only few bytes are transfered on a connection
seeq: use PTR_RET at init_module of driver
bnx2x: remove cast around the kmalloc in bnx2x_prev_mark_path
ipv4: clean up put_child
...
Implement the new swapfile a_ops for NFS and hook up ->direct_IO. This
will set the NFS socket to SOCK_MEMALLOC and run socket reconnect under
PF_MEMALLOC as well as reset SOCK_MEMALLOC before engaging the protocol
->connect() method.
PF_MEMALLOC should allow the allocation of struct socket and related
objects and the early (re)setting of SOCK_MEMALLOC should allow us to
receive the packets required for the TCP connection buildup.
[jlayton@redhat.com: Restore PF_MEMALLOC task flags in all cases]
[dfeng@redhat.com: Fix handling of multiple swap files]
[a.p.zijlstra@chello.nl: Original patch]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Paris <eparis@redhat.com>
Cc: James Morris <jmorris@namei.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Neil Brown <neilb@suse.de>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series is based on top of "Swap-over-NBD without deadlocking
v15" as it depends on the same reservation of PF_MEMALLOC reserves logic.
When a user or administrator requires swap for their application, they
create a swap partition and file, format it with mkswap and activate it
with swapon. In diskless systems this is not an option so if swap if
required then swapping over the network is considered. The two likely
scenarios are when blade servers are used as part of a cluster where the
form factor or maintenance costs do not allow the use of disks and thin
clients.
The Linux Terminal Server Project recommends the use of the Network Block
Device (NBD) for swap but this is not always an option. There is no
guarantee that the network attached storage (NAS) device is running Linux
or supports NBD. However, it is likely that it supports NFS so there are
users that want support for swapping over NFS despite any performance
concern. Some distributions currently carry patches that support swapping
over NFS but it would be preferable to support it in the mainline kernel.
Patch 1 avoids a stream-specific deadlock that potentially affects TCP.
Patch 2 is a small modification to SELinux to avoid using PFMEMALLOC
reserves.
Patch 3 adds three helpers for filesystems to handle swap cache pages.
For example, page_file_mapping() returns page->mapping for
file-backed pages and the address_space of the underlying
swap file for swap cache pages.
Patch 4 adds two address_space_operations to allow a filesystem
to pin all metadata relevant to a swapfile in memory. Upon
successful activation, the swapfile is marked SWP_FILE and
the address space operation ->direct_IO is used for writing
and ->readpage for reading in swap pages.
Patch 5 notes that patch 3 is bolting
filesystem-specific-swapfile-support onto the side and that
the default handlers have different information to what
is available to the filesystem. This patch refactors the
code so that there are generic handlers for each of the new
address_space operations.
Patch 6 adds an API to allow a vector of kernel addresses to be
translated to struct pages and pinned for IO.
Patch 7 adds support for using highmem pages for swap by kmapping
the pages before calling the direct_IO handler.
Patch 8 updates NFS to use the helpers from patch 3 where necessary.
Patch 9 avoids setting PF_private on PG_swapcache pages within NFS.
Patch 10 implements the new swapfile-related address_space operations
for NFS and teaches the direct IO handler how to manage
kernel addresses.
Patch 11 prevents page allocator recursions in NFS by using GFP_NOIO
where appropriate.
Patch 12 fixes a NULL pointer dereference that occurs when using
swap-over-NFS.
With the patches applied, it is possible to mount a swapfile that is on an
NFS filesystem. Swap performance is not great with a swap stress test
taking roughly twice as long to complete than if the swap device was
backed by NBD.
This patch: netvm: prevent a stream-specific deadlock
It could happen that all !SOCK_MEMALLOC sockets have buffered so much data
that we're over the global rmem limit. This will prevent SOCK_MEMALLOC
buffers from receiving data, which will prevent userspace from running,
which is needed to reduce the buffered data.
Fix this by exempting the SOCK_MEMALLOC sockets from the rmem limit. Once
this change it applied, it is important that sockets that set
SOCK_MEMALLOC do not clear the flag until the socket is being torn down.
If this happens, a warning is generated and the tokens reclaimed to avoid
accounting errors until the bug is fixed.
[davem@davemloft.net: Warning about clearing SOCK_MEMALLOC]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to make sure pfmemalloc packets receive all memory needed to
proceed, ensure processing of pfmemalloc SKBs happens under PF_MEMALLOC.
This is limited to a subset of protocols that are expected to be used for
writing to swap. Taps are not allowed to use PF_MEMALLOC as these are
expected to communicate with userspace processes which could be paged out.
[a.p.zijlstra@chello.nl: Ideas taken from various patches]
[jslaby@suse.cz: Lock imbalance fix]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change the skb allocation API to indicate RX usage and use this to fall
back to the PFMEMALLOC reserve when needed. SKBs allocated from the
reserve are tagged in skb->pfmemalloc. If an SKB is allocated from the
reserve and the socket is later found to be unrelated to page reclaim, the
packet is dropped so that the memory remains available for page reclaim.
Network protocols are expected to recover from this packet loss.
[a.p.zijlstra@chello.nl: Ideas taken from various patches]
[davem@davemloft.net: Use static branches, coding style corrections]
[sebastian@breakpoint.cc: Avoid unnecessary cast, fix !CONFIG_NET build]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow specific sockets to be tagged SOCK_MEMALLOC and use __GFP_MEMALLOC
for their allocations. These sockets will be able to go below watermarks
and allocate from the emergency reserve. Such sockets are to be used to
service the VM (iow. to swap over). They must be handled kernel side,
exposing such a socket to user-space is a bug.
There is a risk that the reserves be depleted so for now, the
administrator is responsible for increasing min_free_kbytes as necessary
to prevent deadlock for their workloads.
[a.p.zijlstra@chello.nl: Original patches]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce sk_gfp_atomic(), this function allows to inject sock specific
flags to each sock related allocation. It is only used on allocation
paths that may be required for writing pages back to network storage.
[davem@davemloft.net: Use sk_gfp_atomic only when necessary]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a device is unregistered, we have to purge all of the
references to it that may exist in the entire system.
If a route is uncached, we currently have no way of accomplishing
this.
So create a global list that is scanned when a network device goes
down. This mirrors the logic in net/core/dst.c's dst_ifdown().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull nfsd changes from J. Bruce Fields:
"This has been an unusually quiet cycle--mostly bugfixes and cleanup.
The one large piece is Stanislav's work to containerize the server's
grace period--but that in itself is just one more step in a
not-yet-complete project to allow fully containerized nfs service.
There are a number of outstanding delegation, container, v4 state, and
gss patches that aren't quite ready yet; 3.7 may be wilder."
* 'nfsd-next' of git://linux-nfs.org/~bfields/linux: (35 commits)
NFSd: make boot_time variable per network namespace
NFSd: make grace end flag per network namespace
Lockd: move grace period management from lockd() to per-net functions
LockD: pass actual network namespace to grace period management functions
LockD: manage grace list per network namespace
SUNRPC: service request network namespace helper introduced
NFSd: make nfsd4_manager allocated per network namespace context.
LockD: make lockd manager allocated per network namespace
LockD: manage grace period per network namespace
Lockd: add more debug to host shutdown functions
Lockd: host complaining function introduced
LockD: manage used host count per networks namespace
LockD: manage garbage collection timeout per networks namespace
LockD: make garbage collector network namespace aware.
LockD: mark host per network namespace on garbage collect
nfsd4: fix missing fault_inject.h include
locks: move lease-specific code out of locks_delete_lock
locks: prevent side-effects of locks_release_private before file_lock is initialized
NFSd: set nfsd_serv to NULL after service destruction
NFSd: introduce nfsd_destroy() helper
...
Input path is mostly run under RCU and doesnt touch dst refcnt
But output path on forwarding or UDP workloads hits
badly dst refcount, and we have lot of false sharing, for example
in ipv4_mtu() when reading rt->rt_pmtu
Using a percpu cache for nh_rth_output gives a nice performance
increase at a small cost.
24 udpflood test on my 24 cpu machine (dummy0 output device)
(each process sends 1.000.000 udp frames, 24 processes are started)
before : 5.24 s
after : 2.06 s
For reference, time on linux-3.5 : 6.60 s
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 404e0a8b6a (net: ipv4: fix RCU races on dst refcounts) tried
to solve a race but added a problem at device/fib dismantle time :
We really want to call dst_free() as soon as possible, even if sockets
still have dst in their cache.
dst_release() calls in free_fib_info_rcu() are not welcomed.
Root of the problem was that now we also cache output routes (in
nh_rth_output), we must use call_rcu() instead of call_rcu_bh() in
rt_free(), because output route lookups are done in process context.
Based on feedback and initial patch from David Miller (adding another
call_rcu_bh() call in fib, but it appears it was not the right fix)
I left the inet_sk_rx_dst_set() helper and added __rcu attributes
to nh_rth_output and nh_rth_input to better document what is going on in
this code.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull Ceph changes from Sage Weil:
"Lots of stuff this time around:
- lots of cleanup and refactoring in the libceph messenger code, and
many hard to hit races and bugs closed as a result.
- lots of cleanup and refactoring in the rbd code from Alex Elder,
mostly in preparation for the layering functionality that will be
coming in 3.7.
- some misc rbd cleanups from Josh Durgin that are finally going
upstream
- support for CRUSH tunables (used by newer clusters to improve the
data placement)
- some cleanup in our use of d_parent that Al brought up a while back
- a random collection of fixes across the tree
There is another patch coming that fixes up our ->atomic_open()
behavior, but I'm going to hammer on it a bit more before sending it."
Fix up conflicts due to commits that were already committed earlier in
drivers/block/rbd.c, net/ceph/{messenger.c, osd_client.c}
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (132 commits)
rbd: create rbd_refresh_helper()
rbd: return obj version in __rbd_refresh_header()
rbd: fixes in rbd_header_from_disk()
rbd: always pass ops array to rbd_req_sync_op()
rbd: pass null version pointer in add_snap()
rbd: make rbd_create_rw_ops() return a pointer
rbd: have __rbd_add_snap_dev() return a pointer
libceph: recheck con state after allocating incoming message
libceph: change ceph_con_in_msg_alloc convention to be less weird
libceph: avoid dropping con mutex before fault
libceph: verify state after retaking con lock after dispatch
libceph: revoke mon_client messages on session restart
libceph: fix handling of immediate socket connect failure
ceph: update MAINTAINERS file
libceph: be less chatty about stray replies
libceph: clear all flags on con_close
libceph: clean up con flags
libceph: replace connection state bits with states
libceph: drop unnecessary CLOSED check in socket state change callback
libceph: close socket directly from ceph_con_close()
...
Features include:
- More preparatory patches for modularising NFSv2/v3/v4.
Split out the various NFSv2/v3/v4-specific code into separate
files
- More preparation for the NFSv4 migration code
- Ensure that OPEN(O_CREATE) observes the pNFS mds threshold parameters
- pNFS fast failover when the data servers are down
- Various cleanups and debugging patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQFwYRAAoJEGcL54qWCgDy6YAQAIZuUPFCQbuzWev4L/XA0uhg
0xjr9YBmg57UOs8e7FhS0azJip+D/kmF2Rx5gCMX0QO/IwaEVoms4BS8zjFOr3yL
cPIyY5ErF+WJ25f3Mz8k0wOHTzrOvMdq4/7TQf5hztsrGYFid78sSb3O9ZO9bgb4
QxqhgA0Z4S2vIqeObJAF9BT5UOT/cXfVKV0iTd52ZQVA+ZhqJ2SDlNFsoxnVOweV
qzKOi0FZCPsjH+Z4a/LLdieHG5AYRPhOScBdG7gTFAdkysI8DDtSNCmJ68dMHYRw
OHtyt/X4k9TImfwauV3Eww1sw3NkDswX+dv3GOSDTlMvVBrm0WXWj2zoHZbOB+0Q
ETI9Zpolvd9pADtyfu9c+kCYIR+NdB4lGKd15iZfdEy/CZ0CtbLAbn5Szo2YcwNR
iVjswR0jsbklD+mZjlMeZoG4JX2d9ZRqLs20POz7QQBmdIQ8jb9/SwVj9zGvX0w0
NyVUHTFlGaNwkpo7oeRoWi1xjZWE6OzfoncV/46DOJWb08OKZ4fR4ugMYJWGi7Xx
I4nQrIiHtInqL+sF5Y3wlZ48dufLuIhAcHh7klxgud4GRj7t8j+a99pTrRmpHvvC
4K2Yu69VYcIA7N2RsSLohIllGPFmMwpdar7yERdD0So8/fz/zf7wn0dFFYY11+bL
YNVVGhvNxccMU5EU9YR4
=Lc59
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.6-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client updates from Trond Myklebust:
"Features include:
- More preparatory patches for modularising NFSv2/v3/v4. Split out
the various NFSv2/v3/v4-specific code into separate files
- More preparation for the NFSv4 migration code
- Ensure that OPEN(O_CREATE) observes the pNFS mds threshold
parameters
- pNFS fast failover when the data servers are down
- Various cleanups and debugging patches"
* tag 'nfs-for-3.6-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (67 commits)
nfs: fix fl_type tests in NFSv4 code
NFS: fix pnfs regression with directio writes
NFS: fix pnfs regression with directio reads
sunrpc: clnt: Add missing braces
nfs: fix stub return type warnings
NFS: exit_nfs_v4() shouldn't be an __exit function
SUNRPC: Add a missing spin_unlock to gss_mech_list_pseudoflavors
NFS: Split out NFS v4 client functions
NFS: Split out the NFS v4 filesystem types
NFS: Create a single nfs_clone_super() function
NFS: Split out NFS v4 server creating code
NFS: Initialize the NFS v4 client from init_nfs_v4()
NFS: Move the v4 getroot code to nfs4getroot.c
NFS: Split out NFS v4 file operations
NFS: Initialize v4 sysctls from nfs_init_v4()
NFS: Create an init_nfs_v4() function
NFS: Split out NFS v4 inode operations
NFS: Split out NFS v3 inode operations
NFS: Split out NFS v2 inode operations
NFS: Clean up nfs4_proc_setclientid() and friends
...
We drop the lock when calling the ->alloc_msg() con op, which means
we need to (a) not clobber con->in_msg without the mutex held, and (b)
we need to verify that we are still in the OPEN state when we retake
it to avoid causing any mayhem. If the state does change, -EAGAIN
will get us back to con_work() and loop.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
This function's calling convention is very limiting. In particular,
we can't return any error other than ENOMEM (and only implicitly),
which is a problem (see next patch).
Instead, return an normal 0 or error code, and make the skip a pointer
output parameter. Drop the useless in_hdr argument (we have the con
pointer).
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
The ceph_fault() function takes the con mutex, so we should avoid
dropping it before calling it. This fixes a potential race with
another thread calling ceph_con_close(), or _open(), or similar (we
don't reverify con->state after retaking the lock).
Add annotation so that lockdep realizes we will drop the mutex before
returning.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
We drop the con mutex when delivering a message. When we retake the
lock, we need to verify we are still in the OPEN state before
preparing to read the next tag, or else we risk stepping on a
connection that has been closed.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Revoke all mon_client messages when we shut down the old connection.
This is mostly moot since we are re-using the same ceph_connection,
but it is cleaner.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
If the connect() call immediately fails such that sock == NULL, we
still need con_close_socket() to reset our socket state to CLOSED.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
There are many (normal) conditions that can lead to us getting
unexpected replies, include cluster topology changes, osd failures,
and timeouts. There's no need to spam the console about it.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Rename flags with CON_FLAG prefix, move the definitions into the c file,
and (better) document their meaning.
Signed-off-by: Sage Weil <sage@inktank.com>
Use a simple set of 6 enumerated values for the socket states (CON_STATE_*)
and use those instead of the state bits. All of the con->state checks are
now under the protection of the con mutex, so this is safe. It also
simplifies many of the state checks because we can check for anything other
than the expected state instead of various bits for races we can think of.
This appears to hold up well to stress testing both with and without socket
failure injection on the server side.
Signed-off-by: Sage Weil <sage@inktank.com>
It is simpler to do this immediately, since we already hold the con mutex.
It also avoids the need to deal with a not-quite-CLOSED socket in con_work.
Signed-off-by: Sage Weil <sage@inktank.com>
Take the con mutex before checking whether the connection is closed to
avoid racing with someone else closing it.
Signed-off-by: Sage Weil <sage@inktank.com>
If we fault on a lossy connection, we should still close the socket
immediately, and do so under the con mutex.
We should also take the con mutex before printing out the state bits in
the debug output.
Signed-off-by: Sage Weil <sage@inktank.com>
This is a trivial fix for the debug output, as it is inconsistent
with the function name so may confuse people when debugging.
[elder@inktank.com: switched to use __func__]
Signed-off-by: Jiaju Zhang <jjzhang@suse.de>
Reviewed-by: Alex Elder <elder@inktank.com>
We exponentially back off when we encounter connection errors. If several
errors accumulate, we will eventually wait ages before even trying to
reconnect.
Fix this by resetting the backoff counter after a successful negotiation/
connection with the remote node. Fixes ceph issue #2802.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Take the con mutex while we are initiating a ceph open. This is necessary
because the may have previously been in use and then closed, which could
result in a racing workqueue running con_work().
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Previously, we were opportunistically initializing the bio_iter if it
appeared to be uninitialized in the middle of the read path. The problem
is that a sequence like:
- start reading message
- initialize bio_iter
- read half a message
- messenger fault, reconnect
- restart reading message
- ** bio_iter now non-NULL, not reinitialized **
- read past end of bio, crash
Instead, initialize the bio_iter unconditionally when we allocate/claim
the message for read.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
The linger op registration (i.e., watch) modifies the object state. As
such, the OSD will reply with success if it has already applied without
doing the associated side-effects (setting up the watch session state).
If we lose the ACK and resubmit, we will see success but the watch will not
be correctly registered and we won't get notifies.
To fix this, always resubmit the linger op with a new tid. We accomplish
this by re-registering as a linger (i.e., 'registered') if we are not yet
registered. Then the second loop will treat this just like a normal
case of re-registering.
This mirrors a similar fix on the userland ceph.git, commit 5dd68b95, and
ceph bug #2796.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
Hold the mutex while twiddling all of the state bits to avoid possible
races. While we're here, make not of why we cannot close the socket
directly.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
We need to set error_msg to something useful before calling ceph_fault();
do so here for try_{read,write}(). This is more informative than
libceph: osd0 192.168.106.220:6801 (null)
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
The server side recently added support for tuning some magic
crush variables. Decode these variables if they are present, or use the
default values if they are not present.
Corresponds to ceph.git commit 89af369c25f274fe62ef730e5e8aad0c54f1e5a5.
Signed-off-by: caleb miles <caleb.miles@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
Without this patch kernel will panic on LockD start, because lockd_up() checks
lockd_up_net() result for negative value.
From my pow it's better to return negative value from rpcbind routines instead
of replacing all such checks like in lockd_up().
Signed-off-by: Stanislav Kinsbursky <skinsbursky@parallels.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org [>= 3.0]
This is simply cleanup that will keep things more closely synced with the
userland code.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
Reviewed-by: Yehuda Sadeh <yehuda@inktank.com>
We've had some reports of a deadlock where rpciod ends up with a stack
trace like this:
PID: 2507 TASK: ffff88103691ab40 CPU: 14 COMMAND: "rpciod/14"
#0 [ffff8810343bf2f0] schedule at ffffffff814dabd9
#1 [ffff8810343bf3b8] nfs_wait_bit_killable at ffffffffa038fc04 [nfs]
#2 [ffff8810343bf3c8] __wait_on_bit at ffffffff814dbc2f
#3 [ffff8810343bf418] out_of_line_wait_on_bit at ffffffff814dbcd8
#4 [ffff8810343bf488] nfs_commit_inode at ffffffffa039e0c1 [nfs]
#5 [ffff8810343bf4f8] nfs_release_page at ffffffffa038bef6 [nfs]
#6 [ffff8810343bf528] try_to_release_page at ffffffff8110c670
#7 [ffff8810343bf538] shrink_page_list.clone.0 at ffffffff81126271
#8 [ffff8810343bf668] shrink_inactive_list at ffffffff81126638
#9 [ffff8810343bf818] shrink_zone at ffffffff8112788f
#10 [ffff8810343bf8c8] do_try_to_free_pages at ffffffff81127b1e
#11 [ffff8810343bf958] try_to_free_pages at ffffffff8112812f
#12 [ffff8810343bfa08] __alloc_pages_nodemask at ffffffff8111fdad
#13 [ffff8810343bfb28] kmem_getpages at ffffffff81159942
#14 [ffff8810343bfb58] fallback_alloc at ffffffff8115a55a
#15 [ffff8810343bfbd8] ____cache_alloc_node at ffffffff8115a2d9
#16 [ffff8810343bfc38] kmem_cache_alloc at ffffffff8115b09b
#17 [ffff8810343bfc78] sk_prot_alloc at ffffffff81411808
#18 [ffff8810343bfcb8] sk_alloc at ffffffff8141197c
#19 [ffff8810343bfce8] inet_create at ffffffff81483ba6
#20 [ffff8810343bfd38] __sock_create at ffffffff8140b4a7
#21 [ffff8810343bfd98] xs_create_sock at ffffffffa01f649b [sunrpc]
#22 [ffff8810343bfdd8] xs_tcp_setup_socket at ffffffffa01f6965 [sunrpc]
#23 [ffff8810343bfe38] worker_thread at ffffffff810887d0
#24 [ffff8810343bfee8] kthread at ffffffff8108dd96
#25 [ffff8810343bff48] kernel_thread at ffffffff8100c1ca
rpciod is trying to allocate memory for a new socket to talk to the
server. The VM ends up calling ->releasepage to get more memory, and it
tries to do a blocking commit. That commit can't succeed however without
a connected socket, so we deadlock.
Fix this by setting PF_FSTRANS on the workqueue task prior to doing the
socket allocation, and having nfs_release_page check for that flag when
deciding whether to do a commit call. Also, set PF_FSTRANS
unconditionally in rpc_async_schedule since that function can also do
allocations sometimes.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
rpc_make_runnable is not generally called with the queue lock held, unless
it's waking up a task that has been sitting on a waitqueue. This is safe
when the task has not entered the FSM yet, but the comments don't really
spell this out.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add a missing set of braces that commit 4e0038b6b2
("SUNRPC: Move clnt->cl_server into struct rpc_xprt")
forgot.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org [>= 3.4]
After IP route cache removal, rt_cache_rebuild_count is no longer
used.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit c6cffba4ff (ipv4: Fix input route performance regression.)
added various fatal races with dst refcounts.
crashes happen on tcp workloads if routes are added/deleted at the same
time.
The dst_free() calls from free_fib_info_rcu() are clearly racy.
We need instead regular dst refcounting (dst_release()) and make
sure dst_release() is aware of RCU grace periods :
Add DST_RCU_FREE flag so that dst_release() respects an RCU grace period
before dst destruction for cached dst
Introduce a new inet_sk_rx_dst_set() helper, using atomic_inc_not_zero()
to make sure we dont increase a zero refcount (On a dst currently
waiting an rcu grace period before destruction)
rt_cache_route() must take a reference on the new cached route, and
release it if was not able to install it.
With this patch, my machines survive various benchmarks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
early_demux() handlers should be called in RCU context, and as we
use skb_dst_set_noref(skb, dst), caller must not exit from RCU context
before dst use (skb_dst(skb)) or release (skb_drop(dst))
Therefore, rcu_read_lock()/rcu_read_unlock() pairs around
->early_demux() are confusing and not needed :
Protocol handlers are already in an RCU read lock section.
(__netif_receive_skb() does the rcu_read_lock() )
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an atomic variable 'stopping' as flag in struct ceph_messenger,
set this flag to 1 in function ceph_destroy_client(), and add the condition code
in function ceph_data_ready() to test the flag value, if true(1), just return.
Signed-off-by: Guanjun He <gjhe@suse.com>
Reviewed-by: Sage Weil <sage@inktank.com>
In ancient times, the messenger could both initiate and accept connections.
An artifact if that was data structures to store/process an incoming
ceph_msg_connect request and send an outgoing ceph_msg_connect_reply.
Sadly, the negotiation code was referencing those structures and ignoring
important information (like the peer's connect_seq) from the correct ones.
Among other things, this fixes tight reconnect loops where the server sends
RETRY_SESSION and we (the client) retries with the same connect_seq as last
time. This bug pretty easily triggered by injecting socket failures on the
MDS and running some fs workload like workunits/direct_io/test_sync_io.
Signed-off-by: Sage Weil <sage@inktank.com>
These don't strictly need to be initialized based on how they are used, but
it is good practice to do so.
Reported-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Initialize the type field for messages in a msgpool. The caller was doing
this for osd ops, but not for the reply messages.
Reported-by: Alex Elder <elder@inktank.com>
Signed-off-by: Sage Weil <sage@inktank.com>
ieee80211_request_sched_scan_stop() cleared
local->sched_scan_sdata. However, sched_scan_sdata
should be cleared only after the driver calls
ieee80211_sched_scan_stopped() (like with normal hw scan).
Clearing sched_scan_sdata too early caused
ieee80211_sched_scan_stopped_work to exit prematurely
without properly cleaning all the sched scan resources
and without calling cfg80211_sched_scan_stopped (so
userspace wasn't notified about sched scan completion).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When userspace use RTM_GETROUTE to dump route table, with an already
expired route entry, we always got an 'expires' value(2147157)
calculated base on INT_MAX.
The reason of this problem is in the following satement:
rt->dst.expires - jiffies < INT_MAX
gcc promoted the type of both sides of '<' to unsigned long, thus
a small negative value would be considered greater than INT_MAX.
With the help of Eric Dumazet, do the out of bound checks in
rtnl_put_cacheinfo(), _after_ conversion to clock_t.
Signed-off-by: Li Wei <lw@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first parameter struct trie *t is not used anymore.
Remove it.
Signed-off-by: Lin Ming <mlin@ss.pku.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should print size of struct rt_trie_node * allocated instead of size
of struct rt_trie_node.
Signed-off-by: Lin Ming <mlin@ss.pku.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
One side effect - attempt to create a cross-device link on a read-only fs fails
with EROFS instead of EXDEV now. Makes more sense, POSIX allows, etc.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Back in 2006, commit 1a2449a87b ("[I/OAT]: TCP recv offload to I/OAT")
added support for receive offloading to IOAT dma engine if available.
The code in tcp_rcv_established() tries to perform early DMA copy if
applicable. It however does so without checking whether the userspace
task is actually expecting the data in the buffer.
This is not a problem under normal circumstances, but there is a corner
case where this doesn't work -- and that's when MSG_TRUNC flag to
recvmsg() is used.
If the IOAT dma engine is not used, the code properly checks whether
there is a valid ucopy.task and the socket is owned by userspace, but
misses the check in the dmaengine case.
This problem can be observed in real trivially -- for example 'tbench' is a
good reproducer, as it makes a heavy use of MSG_TRUNC. On systems utilizing
IOAT, you will soon find tbench waiting indefinitely in sk_wait_data(), as they
have been already early-copied in tcp_rcv_established() using dma engine.
This patch introduces the same check we are performing in the simple
iovec copy case to the IOAT case as well. It fixes the indefinite
recvmsg(MSG_TRUNC) hangs.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 5b3e7e6cb5.
The problem that the original commit was attempting to fix can
never happen in practice because validation is done one a per-flow
basis rather than a per-packet basis. Adding additional checks at
runtime is unnecessary and inconsistent with the rest of the code.
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 92101b3b2e (ipv4: Prepare for change of rt->rt_iif encoding.)
invalidated TCP early demux, because rx_dst_ifindex is not properly
initialized and checked.
Also remove the use of inet_iif(skb) in favor or skb->skb_iif
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When device flags are set using rtnetlink, IFF_PROMISC and IFF_ALLMULTI
flags are handled specially. Function dev_change_flags sets IFF_PROMISC and
IFF_ALLMULTI bits in dev->gflags according to the passed value but
do_setlink passes a result of rtnl_dev_combine_flags which takes those bits
from dev->flags.
This can be easily trigerred by doing:
tcpdump -i eth0 &
ip l s up eth0
ip sets IFF_UP flag in ifi_flags and ifi_change, which is combined with
IFF_PROMISC by rtnl_dev_combine_flags, causing __dev_change_flags to set
IFF_PROMISC in gflags.
Reported-by: Max Matveev <makc@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_USER_TIMEOUT is a TCP level socket option that takes an unsigned int. But
patch "tcp: Add TCP_USER_TIMEOUT socket option"(dca43c75) didn't check the negative
values. If a user assign -1 to it, the socket will set successfully and wait
for 4294967295 miliseconds. This patch add a negative value check to avoid
this issue.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull LED subsystem update from Bryan Wu.
* 'for-3.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds: (50 commits)
leds-lp8788: forgotten unlock at lp8788_led_work
LEDS: propagate error codes in blinkm_detect()
LEDS: memory leak in blinkm_led_common_set()
leds: add new lp8788 led driver
LEDS: add BlinkM RGB LED driver, documentation and update MAINTAINERS
leds: max8997: Simplify max8997_led_set_mode implementation
leds/leds-s3c24xx: use devm_gpio_request
leds: convert Network Space v2 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert DAC124S085 LED driver to devm_kzalloc()
leds: convert LM3530 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert TCA6507 LED driver to devm_kzalloc()
leds: convert Freescale MC13783 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert ADP5520 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert PCA955x LED driver to devm_kzalloc() and cleanup error exit path
leds: convert Sun Fire LED driver to devm_kzalloc() and cleanup error exit path
leds: convert PCA9532 LED driver to devm_kzalloc()
leds: convert LT3593 LED driver to devm_kzalloc()
leds: convert Renesas TPU LED driver to devm_kzalloc() and cleanup error exit path
leds: convert LP5523 LED driver to devm_kzalloc() and cleanup error exit path
leds: convert PCA9633 LED driver to devm_kzalloc()
...
Pull networking updates and fixes from David Miller:
1) Reinstate the no-ref optimization for input route lookups in ipv4 to
fix some routing cache removal perf regressions.
2) Make TCP socket pre-demux work on ipv6 side too, from Eric Dumazet.
3) Get RX hash value from correct place in be2net driver, from
Sarveshwar Bandi.
4) Validation of FIB cached routes missing critical check, from Eric
Dumazet.
5) EEH support in mlx4 driver, from Kleber Sacilotto de Souza.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
ipv6: Early TCP socket demux
ipv4: Fix input route performance regression.
pch_gbe: vlan skb len fix
pch_gbe: add extra clean tx
pch_gbe: fix transmit watchdog timeout
ixgbe: fix panic while dumping packets on Tx hang with IOMMU
be2net: Fix to parse RSS hash from Receive completions correctly.
net/mlx4_en: Limit the RFS filter IDs to be < RPS_NO_FILTER
hyperv: Add error handling to rndis_filter_device_add()
hyperv: Add a check for ring_size value
ipv4: rt_cache_valid must check expired routes
net/pch_gpe: Cannot disable ethernet autonegation
qeth: repair crash in qeth_l3_vlan_rx_kill_vid()
netiucv: cleanup attribute usage
net: wiznet add missing HAS_IOMEM dependency
be2net: Missing byteswap in be_get_fw_log_level causes oops on PowerPC
mlx4: Add support for EEH error recovery
cdc-ncm: tag Ericsson WWAN devices (eg F5521gw) with FLAG_WWAN
wanmain: comparing array with NULL
caif: fix NULL pointer check
...
This is the IPv6 missing bits for infrastructure added in commit
41063e9dd1 (ipv4: Early TCP socket demux.)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the routing cache removal we lost the "noref" code paths on
input, and this can kill some routing workloads.
Reinstate the noref path when we hit a cached route in the FIB
nexthops.
With help from Eric Dumazet.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d2d68ba9fe (ipv4: Cache input routes in fib_info nexthops.)
introduced rt_cache_valid() helper. It unfortunately doesn't check if
route is expired before caching it.
I noticed sk_setup_caps() was constantly called on a tcp workload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit eccc068e8e
Author: Hong Wu <Hong.Wu@dspg.com>
Date: Wed Jan 11 20:33:39 2012 +0200
wireless: Save original maximum regulatory transmission power for the calucation of the local maximum transmit pow
changed the way we calculate chan->max_power as min(chan->max_power,
chan->max_reg_power). That broke rt2x00 (and perhaps some other
drivers) that do not set chan->max_power. It is not so easy to fix this
problem correctly in rt2x00.
According to commit eccc068e8 changelog, change claim only to save
maximum regulatory power - changing setting of chan->max_power was side
effect. This patch restore previous calculations of chan->max_power and
do not touch chan->max_reg_power.
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
1) Remove a non needed pskb_may_pull() in tcp_v4_early_demux()
and fix a potential bug if skb->head was reallocated
(iph & th pointers were not reloaded)
TCP stack will pull/check headers anyway.
2) must reload iph in ip_rcv_finish() after early_demux()
call since skb->head might have changed.
3) skb->dev->ifindex can be now replaced by skb->skb_iif
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree from Jiri Kosina:
"Trivial updates all over the place as usual."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (29 commits)
Fix typo in include/linux/clk.h .
pci: hotplug: Fix typo in pci
iommu: Fix typo in iommu
video: Fix typo in drivers/video
Documentation: Add newline at end-of-file to files lacking one
arm,unicore32: Remove obsolete "select MISC_DEVICES"
module.c: spelling s/postition/position/g
cpufreq: Fix typo in cpufreq driver
trivial: typo in comment in mksysmap
mach-omap2: Fix typo in debug message and comment
scsi: aha152x: Fix sparse warning and make printing pointer address more portable.
Change email address for Steve Glendinning
Btrfs: fix typo in convert_extent_bit
via: Remove bogus if check
netprio_cgroup.c: fix comment typo
backlight: fix memory leak on obscure error path
Documentation: asus-laptop.txt references an obsolete Kconfig item
Documentation: ManagementStyle: fixed typo
mm/vmscan: cleanup comment error in balance_pgdat
mm: cleanup on the comments of zone_reclaim_stat
...
Pull networking changes from David S Miller:
1) Remove the ipv4 routing cache. Now lookups go directly into the FIB
trie and use prebuilt routes cached there.
No more garbage collection, no more rDOS attacks on the routing
cache. Instead we now get predictable and consistent performance,
no matter what the pattern of traffic we service.
This has been almost 2 years in the making. Special thanks to
Julian Anastasov, Eric Dumazet, Steffen Klassert, and others who
have helped along the way.
I'm sure that with a change of this magnitude there will be some
kind of fallout, but such things ought the be simple to fix at this
point. Luckily I'm not European so I'll be around all of August to
fix things :-)
The major stages of this work here are each fronted by a forced
merge commit whose commit message contains a top-level description
of the motivations and implementation issues.
2) Pre-demux of established ipv4 TCP sockets, saves a route demux on
input.
3) TCP SYN/ACK performance tweaks from Eric Dumazet.
4) Add namespace support for netfilter L4 conntrack helpers, from Gao
Feng.
5) Add config mechanism for Energy Efficient Ethernet to ethtool, from
Yuval Mintz.
6) Remove quadratic behavior from /proc/net/unix, from Eric Dumazet.
7) Support for connection tracker helpers in userspace, from Pablo
Neira Ayuso.
8) Allow userspace driven TX load balancing functions in TEAM driver,
from Jiri Pirko.
9) Kill off NLMSG_PUT and RTA_PUT macros, more gross stuff with
embedded gotos.
10) TCP Small Queues, essentially minimize the amount of TCP data queued
up in the packet scheduler layer. Whereas the existing BQL (Byte
Queue Limits) limits the pkt_sched --> netdevice queuing levels,
this controls the TCP --> pkt_sched queueing levels.
From Eric Dumazet.
11) Reduce the number of get_page/put_page ops done on SKB fragments,
from Alexander Duyck.
12) Implement protection against blind resets in TCP (RFC 5961), from
Eric Dumazet.
13) Support the client side of TCP Fast Open, basically the ability to
send data in the SYN exchange, from Yuchung Cheng.
Basically, the sender queues up data with a sendmsg() call using
MSG_FASTOPEN, then they do the connect() which emits the queued up
fastopen data.
14) Avoid all the problems we get into in TCP when timers or PMTU events
hit a locked socket. The TCP Small Queues changes added a
tcp_release_cb() that allows us to queue work up to the
release_sock() caller, and that's what we use here too. From Eric
Dumazet.
15) Zero copy on TX support for TUN driver, from Michael S. Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1870 commits)
genetlink: define lockdep_genl_is_held() when CONFIG_LOCKDEP
r8169: revert "add byte queue limit support".
ipv4: Change rt->rt_iif encoding.
net: Make skb->skb_iif always track skb->dev
ipv4: Prepare for change of rt->rt_iif encoding.
ipv4: Remove all RTCF_DIRECTSRC handliing.
ipv4: Really ignore ICMP address requests/replies.
decnet: Don't set RTCF_DIRECTSRC.
net/ipv4/ip_vti.c: Fix __rcu warnings detected by sparse.
ipv4: Remove redundant assignment
rds: set correct msg_namelen
openvswitch: potential NULL deref in sample()
tcp: dont drop MTU reduction indications
bnx2x: Add new 57840 device IDs
tcp: avoid oops in tcp_metrics and reset tcpm_stamp
niu: Change niu_rbr_fill() to use unlikely() to check niu_rbr_add_page() return value
niu: Fix to check for dma mapping errors.
net: Fix references to out-of-scope variables in put_cmsg_compat()
net: ethernet: davinci_emac: add pm_runtime support
net: ethernet: davinci_emac: Remove unnecessary #include
...
lockdep_is_held() is defined when CONFIG_LOCKDEP, not CONFIG_PROVE_LOCKING.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename leds external interface led_brightness_set() to led_set_brightness().
This is the second phase of the change to reduce confusion between the
leds internal and external interfaces that set brightness. With this change,
now the external interface is led_set_brightness(). The first phase renamed
the internal interface led_set_brightness() to __led_set_brightness().
There are no changes to the interface implementations.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
On input packet processing, rt->rt_iif will be zero if we should
use skb->dev->ifindex.
Since we access rt->rt_iif consistently via inet_iif(), that is
the only spot whose interpretation have to adjust.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it follow device decapsulation, from things such as VLAN and
bonding.
The stuff that actually cares about pre-demuxed device pointers, is
handled by the "orig_dev" variable in __netif_receive_skb(). And
the only consumer of that is the po->origdev feature of AF_PACKET
sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use inet_iif() consistently, and for TCP record the input interface of
cached RX dst in inet sock.
rt->rt_iif is going to be encoded differently, so that we can
legitimately cache input routes in the FIB info more aggressively.
When the input interface is "use SKB device index" the rt->rt_iif will
be set to zero.
This forces us to move the TCP RX dst cache installation into the ipv4
specific code, and as well it should since doing the route caching for
ipv6 is pointless at the moment since it is not inspected in the ipv6
input paths yet.
Also, remove the unlikely on dst->obsolete, all ipv4 dsts have
obsolete set to a non-zero value to force invocation of the check
callback.
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey removed kernel side support for requests, and the
only thing we do for replies is log a message if something
doesn't look right.
As Alexey's comment indicates, this belongs in userspace (if
anywhere), and thus we can safely just get rid of this code.
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_SPARSE_RCU_POINTER=y sparse identified references which did not
specificy __rcu in ip_vti.c
Signed-off-by: Saurabh Mohan <saurabh.mohan@vyatta.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is redundant to set no_addr and accept_local to 0 and then set them
with other values just after that.
Signed-off-by: Lin Ming <mlin@ss.pku.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull the big VFS changes from Al Viro:
"This one is *big* and changes quite a few things around VFS. What's in there:
- the first of two really major architecture changes - death to open
intents.
The former is finally there; it was very long in making, but with
Miklos getting through really hard and messy final push in
fs/namei.c, we finally have it. Unlike his variant, this one
doesn't introduce struct opendata; what we have instead is
->atomic_open() taking preallocated struct file * and passing
everything via its fields.
Instead of returning struct file *, it returns -E... on error, 0
on success and 1 in "deal with it yourself" case (e.g. symlink
found on server, etc.).
See comments before fs/namei.c:atomic_open(). That made a lot of
goodies finally possible and quite a few are in that pile:
->lookup(), ->d_revalidate() and ->create() do not get struct
nameidata * anymore; ->lookup() and ->d_revalidate() get lookup
flags instead, ->create() gets "do we want it exclusive" flag.
With the introduction of new helper (kern_path_locked()) we are rid
of all struct nameidata instances outside of fs/namei.c; it's still
visible in namei.h, but not for long. Come the next cycle,
declaration will move either to fs/internal.h or to fs/namei.c
itself. [me, miklos, hch]
- The second major change: behaviour of final fput(). Now we have
__fput() done without any locks held by caller *and* not from deep
in call stack.
That obviously lifts a lot of constraints on the locking in there.
Moreover, it's legal now to call fput() from atomic contexts (which
has immediately simplified life for aio.c). We also don't need
anti-recursion logics in __scm_destroy() anymore.
There is a price, though - the damn thing has become partially
asynchronous. For fput() from normal process we are guaranteed
that pending __fput() will be done before the caller returns to
userland, exits or gets stopped for ptrace.
For kernel threads and atomic contexts it's done via
schedule_work(), so theoretically we might need a way to make sure
it's finished; so far only one such place had been found, but there
might be more.
There's flush_delayed_fput() (do all pending __fput()) and there's
__fput_sync() (fput() analog doing __fput() immediately). I hope
we won't need them often; see warnings in fs/file_table.c for
details. [me, based on task_work series from Oleg merged last
cycle]
- sync series from Jan
- large part of "death to sync_supers()" work from Artem; the only
bits missing here are exofs and ext4 ones. As far as I understand,
those are going via the exofs and ext4 trees resp.; once they are
in, we can put ->write_super() to the rest, along with the thread
calling it.
- preparatory bits from unionmount series (from dhowells).
- assorted cleanups and fixes all over the place, as usual.
This is not the last pile for this cycle; there's at least jlayton's
ESTALE work and fsfreeze series (the latter - in dire need of fixes,
so I'm not sure it'll make the cut this cycle). I'll probably throw
symlink/hardlink restrictions stuff from Kees into the next pile, too.
Plus there's a lot of misc patches I hadn't thrown into that one -
it's large enough as it is..."
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (127 commits)
ext4: switch EXT4_IOC_RESIZE_FS to mnt_want_write_file()
btrfs: switch btrfs_ioctl_balance() to mnt_want_write_file()
switch dentry_open() to struct path, make it grab references itself
spufs: shift dget/mntget towards dentry_open()
zoran: don't bother with struct file * in zoran_map
ecryptfs: don't reinvent the wheels, please - use struct completion
don't expose I_NEW inodes via dentry->d_inode
tidy up namei.c a bit
unobfuscate follow_up() a bit
ext3: pass custom EOF to generic_file_llseek_size()
ext4: use core vfs llseek code for dir seeks
vfs: allow custom EOF in generic_file_llseek code
vfs: Avoid unnecessary WB_SYNC_NONE writeback during sys_sync and reorder sync passes
vfs: Remove unnecessary flushing of block devices
vfs: Make sys_sync writeout also block device inodes
vfs: Create function for iterating over block devices
vfs: Reorder operations during sys_sync
quota: Move quota syncing to ->sync_fs method
quota: Split dquot_quota_sync() to writeback and cache flushing part
vfs: Move noop_backing_dev_info check from sync into writeback
...
Jay Fenlason (fenlason@redhat.com) found a bug,
that recvfrom() on an RDS socket can return the contents of random kernel
memory to userspace if it was called with a address length larger than
sizeof(struct sockaddr_in).
rds_recvmsg() also fails to set the addr_len paramater properly before
returning, but that's just a bug.
There are also a number of cases wher recvfrom() can return an entirely bogus
address. Anything in rds_recvmsg() that returns a non-negative value but does
not go through the "sin = (struct sockaddr_in *)msg->msg_name;" code path
at the end of the while(1) loop will return up to 128 bytes of kernel memory
to userspace.
And I write two test programs to reproduce this bug, you will see that in
rds_server, fromAddr will be overwritten and the following sock_fd will be
destroyed.
Yes, it is the programmer's fault to set msg_namelen incorrectly, but it is
better to make the kernel copy the real length of address to user space in
such case.
How to run the test programs ?
I test them on 32bit x86 system, 3.5.0-rc7.
1 compile
gcc -o rds_client rds_client.c
gcc -o rds_server rds_server.c
2 run ./rds_server on one console
3 run ./rds_client on another console
4 you will see something like:
server is waiting to receive data...
old socket fd=3
server received data from client:data from client
msg.msg_namelen=32
new socket fd=-1067277685
sendmsg()
: Bad file descriptor
/***************** rds_client.c ********************/
int main(void)
{
int sock_fd;
struct sockaddr_in serverAddr;
struct sockaddr_in toAddr;
char recvBuffer[128] = "data from client";
struct msghdr msg;
struct iovec iov;
sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if (sock_fd < 0) {
perror("create socket error\n");
exit(1);
}
memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4001);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind() error\n");
close(sock_fd);
exit(1);
}
memset(&toAddr, 0, sizeof(toAddr));
toAddr.sin_family = AF_INET;
toAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
toAddr.sin_port = htons(4000);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = strlen(recvBuffer) + 1;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendto() error\n");
close(sock_fd);
exit(1);
}
printf("client send data:%s\n", recvBuffer);
memset(recvBuffer, '\0', 128);
msg.msg_name = &toAddr;
msg.msg_namelen = sizeof(toAddr);
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("receive data from server:%s\n", recvBuffer);
close(sock_fd);
return 0;
}
/***************** rds_server.c ********************/
int main(void)
{
struct sockaddr_in fromAddr;
int sock_fd;
struct sockaddr_in serverAddr;
unsigned int addrLen;
char recvBuffer[128];
struct msghdr msg;
struct iovec iov;
sock_fd = socket(AF_RDS, SOCK_SEQPACKET, 0);
if(sock_fd < 0) {
perror("create socket error\n");
exit(0);
}
memset(&serverAddr, 0, sizeof(serverAddr));
serverAddr.sin_family = AF_INET;
serverAddr.sin_addr.s_addr = inet_addr("127.0.0.1");
serverAddr.sin_port = htons(4000);
if (bind(sock_fd, (struct sockaddr*)&serverAddr, sizeof(serverAddr)) < 0) {
perror("bind error\n");
close(sock_fd);
exit(1);
}
printf("server is waiting to receive data...\n");
msg.msg_name = &fromAddr;
/*
* I add 16 to sizeof(fromAddr), ie 32,
* and pay attention to the definition of fromAddr,
* recvmsg() will overwrite sock_fd,
* since kernel will copy 32 bytes to userspace.
*
* If you just use sizeof(fromAddr), it works fine.
* */
msg.msg_namelen = sizeof(fromAddr) + 16;
/* msg.msg_namelen = sizeof(fromAddr); */
msg.msg_iov = &iov;
msg.msg_iovlen = 1;
msg.msg_iov->iov_base = recvBuffer;
msg.msg_iov->iov_len = 128;
msg.msg_control = 0;
msg.msg_controllen = 0;
msg.msg_flags = 0;
while (1) {
printf("old socket fd=%d\n", sock_fd);
if (recvmsg(sock_fd, &msg, 0) == -1) {
perror("recvmsg() error\n");
close(sock_fd);
exit(1);
}
printf("server received data from client:%s\n", recvBuffer);
printf("msg.msg_namelen=%d\n", msg.msg_namelen);
printf("new socket fd=%d\n", sock_fd);
strcat(recvBuffer, "--data from server");
if (sendmsg(sock_fd, &msg, 0) == -1) {
perror("sendmsg()\n");
close(sock_fd);
exit(1);
}
}
close(sock_fd);
return 0;
}
Signed-off-by: Weiping Pan <wpan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no OVS_SAMPLE_ATTR_ACTIONS set then "acts_list" is NULL and
it leads to a NULL dereference when we call nla_len(acts_list). This
is a static checker fix, not something I have seen in testing.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICMP messages generated in output path if frame length is bigger than
mtu are actually lost because socket is owned by user (doing the xmit)
One example is the ipgre_tunnel_xmit() calling
icmp_send(skb, ICMP_DEST_UNREACH, ICMP_FRAG_NEEDED, htonl(mtu));
We had a similar case fixed in commit a34a101e1e (ipv6: disable GSO on
sockets hitting dst_allfrag).
Problem of such fix is that it relied on retransmit timers, so short tcp
sessions paid a too big latency increase price.
This patch uses the tcp_release_cb() infrastructure so that MTU
reduction messages (ICMP messages) are not lost, and no extra delay
is added in TCP transmits.
Reported-by: Maciej Żenczykowski <maze@google.com>
Diagnosed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Tore Anderson <tore@fud.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tcp_tw_remember_stamp we incorrectly checked tw
instead of tm, it can lead to oops if the cached entry is
not found.
tcpm_stamp was not updated in tcpm_check_stamp when
tcpm_suck_dst was called, move the update into tcpm_suck_dst,
so that we do not call it infinitely on every next cache hit
after TCP_METRICS_TIMEOUT.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In net/compat.c::put_cmsg_compat() we may assign 'data' the address of
either the 'ctv' or 'cts' local variables inside the 'if
(!COMPAT_USE_64BIT_TIME)' branch.
Those variables go out of scope at the end of the 'if' statement, so
when we use 'data' further down in 'copy_to_user(CMSG_COMPAT_DATA(cm),
data, cmlen - sizeof(struct compat_cmsghdr))' there's no telling what
it may be refering to - not good.
Fix the problem by simply giving 'ctv' and 'cts' function scope.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
The general flow of this patch series is that first the routing cache
is removed. We build a completely new rtable entry every lookup
request.
Next we make some simplifications due to the fact that removing the
routing cache causes several members of struct rtable to become no
longer necessary.
Then we need to make some amends such that we can legally cache
pre-constructed routes in the FIB nexthops. Firstly, we need to
invalidate routes which are hit with nexthop exceptions. Secondly we
have to change the semantics of rt->rt_gateway such that zero means
that the destination is on-link and non-zero otherwise.
Now that the preparations are ready, we start caching precomputed
routes in the FIB nexthops. Output and input routes need different
kinds of care when determining if we can legally do such caching or
not. The details are in the commit log messages for those changes.
The patch series then winds down with some more struct rtable
simplifications and other tidy ups that remove unnecessary overhead.
On a SPARC-T3 output route lookups are ~876 cycles. Input route
lookups are ~1169 cycles with rpfilter disabled, and about ~1468
cycles with rpfilter enabled.
These measurements were taken with the kbench_mod test module in the
net_test_tools GIT tree:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net_test_tools.git
That GIT tree also includes a udpflood tester tool and stresses
route lookups on packet output.
For example, on the same SPARC-T3 system we can run:
time ./udpflood -l 10000000 10.2.2.11
with routing cache:
real 1m21.955s user 0m6.530s sys 1m15.390s
without routing cache:
real 1m31.678s user 0m6.520s sys 1m25.140s
Performance undoubtedly can easily be improved further.
For example fib_table_lookup() performs a lot of excessive
computations with all the masking and shifting, some of it
conditionalized to deal with edge cases.
Also, Eric's no-ref optimization for input route lookups can be
re-instated for the FIB nexthop caching code path. I would be really
pleased if someone would work on that.
In fact anyone suitable motivated can just fire up perf on the loading
of the test net_test_tools benchmark kernel module. I spend much of
my time going:
bash# perf record insmod ./kbench_mod.ko dst=172.30.42.22 src=74.128.0.1 iif=2
bash# perf report
Thanks to helpful feedback from Joe Perches, Eric Dumazet, Ben
Hutchings, and others.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of updating the sk_cgrp_prioidx struct field on every send
this only updates the field when a task is moved via cgroup
infrastructure.
This allows sockets that may be used by a kernel worker thread
to be managed. For example in the iscsi case today a user can
put iscsid in a netprio cgroup and control traffic will be sent
with the correct sk_cgrp_prioidx value set but as soon as data
is sent the kernel worker thread isssues a send and sk_cgrp_prioidx
is updated with the kernel worker threads value which is the
default case.
It seems more correct to only update the field when the user
explicitly sets it via control group infrastructure. This allows
the users to manage sockets that may be used with other threads.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export skb_copy_ubufs so that modules can orphan frags.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
zero copy packets are normally sent to the outside
network, but bridging, tun etc might loop them
back to host networking stack. If this happens
destructors will never be called, so orphan
the frags immediately on receive.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce code duplication a bit using the new helper.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 76ff5cc919
(rtnl: allow to specify number of rx and tx queues
on device creation) added a reference to the net_device
structure's 'num_rx_queues' member in
net/core/rtnetlink.c:rtnl_fill_ifinfo()
However, the definition for 'num_rx_queues' is surrounded
by an '#ifdef CONFIG_RPS' while the new reference to it is
not. This causes a compile error when CONFIG_RPS is not
defined.
Fix the compile error by surrounding the new reference to
'num_rx_queues' by an '#ifdef CONFIG_RPS'.
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've seen several attempts recently made to do quick failover of sctp transports
by reducing various retransmit timers and counters. While its possible to
implement a faster failover on multihomed sctp associations, its not
particularly robust, in that it can lead to unneeded retransmits, as well as
false connection failures due to intermittent latency on a network.
Instead, lets implement the new ietf quick failover draft found here:
http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
This will let the sctp stack identify transports that have had a small number of
errors, and avoid using them quickly until their reliability can be
re-established. I've tested this out on two virt guests connected via multiple
isolated virt networks and believe its in compliance with the above draft and
works well.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Vlad Yasevich <vyasevich@gmail.com>
CC: Sridhar Samudrala <sri@us.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: linux-sctp@vger.kernel.org
CC: joe@perches.com
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix race condition in several network drivers when reading stats on 32bit
UP architectures. These drivers update their stats in a BH context and
therefore should use u64_stats_fetch_begin_bh/u64_stats_fetch_retry_bh
instead of u64_stats_fetch_begin/u64_stats_fetch_retry when reading the
stats.
Signed-off-by: Kevin Groeneveld <kgroeneveld@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set unicast_sock uc_ttl to -1 so that we select the right ttl,
instead of sending packets with a 0 ttl.
Bug added in commit be9f4a44e7 (ipv4: tcp: remove per net tcp_sock)
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
A few bug fixes and small enhancements for net-next/3.6.
...
Ansis Atteka (1):
openvswitch: Do not send notification if ovs_vport_set_options() failed
Ben Pfaff (1):
openvswitch: Check gso_type for correct sk_buff in queue_gso_packets().
Jesse Gross (2):
openvswitch: Enable retrieval of TCP flags from IPv6 traffic.
openvswitch: Reset upper layer protocol info on internal devices.
Leo Alterman (1):
openvswitch: Fix typo in documentation.
Pravin B Shelar (1):
openvswitch: Check currect return value from skb_gso_segment()
Raju Subramanian (1):
openvswitch: Replace Nicira Networks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
At the point where it was used, skb_shinfo(skb)->gso_type referred to a
post-GSO sk_buff. Thus, it would always be 0. We want to know the pre-GSO
gso_type, so we need to obtain it before segmenting.
Before this change, the kernel would pass inconsistent data to userspace:
packets for UDP fragments with nonzero offset would be passed along with
flow keys that indicate a zero offset (that is, the flow key for "later"
fragments claimed to be "first" fragments). This inconsistency tended
to confuse Open vSwitch userspace, causing it to log messages about
"failed to flow_del" the flows with "later" fragments.
Signed-off-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
It's not really needed.
We only grabbed a reference to the fib_info for the sake of fib_info
local metrics.
However, fib_info objects are freed using RCU, as are therefore their
private metrics (if any).
We would have triggered a route cache flush if we eliminated a
reference to a fib_info object in the routing tables.
Therefore, any existing cached routes will first check and see that
they have been invalidated before an errant reference to these
metric values would occur.
Signed-off-by: David S. Miller <davem@davemloft.net>
That is this value's only use, as a boolean to indicate whether
a route is an input route or not.
So implement it that way, using a u16 gap present in the struct
already.
Signed-off-by: David S. Miller <davem@davemloft.net>
Never actually used.
It was being set on output routes to the original OIF specified in the
flow key used for the lookup.
Adjust the only user, ipmr_rt_fib_lookup(), for greater correctness of
the flowi4_oif and flowi4_iif values, thanks to feedback from Julian
Anastasov.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't bother incrementing dst->__use and setting dst->lastuse,
they are completely pointless and just slow things down.
Signed-off-by: David S. Miller <davem@davemloft.net>
Caching input routes is slightly simpler than output routes, since we
don't need to be concerned with nexthop exceptions. (locally
destined, and routed packets, never trigger PMTU events or redirects
that will be processed by us).
However, we have to elide caching for the DIRECTSRC and non-zero itag
cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have an output route that lacks nexthop exceptions, we can cache
it in the FIB info nexthop.
Such routes will have DST_HOST cleared because such routes refer to a
family of destinations, rather than just one.
The sequence of the handling of exceptions during route lookup is
adjusted to make the logic work properly.
Before we allocate the route, we lookup the exception.
Then we know if we will cache this route or not, and therefore whether
DST_HOST should be set on the allocated route.
Then we use DST_HOST to key off whether we should store the resulting
route, during rt_set_nexthop(), in the FIB nexthop cache.
With help from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a big comment explaining how the field works, and use defines
instead of magic constants for the values assigned to it.
Suggested by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow prefixed routes, we have to adjust how rt_gateway
is set and interpreted.
The new interpretation is:
1) rt_gateway == 0, destination is on-link, nexthop is iph->daddr
2) rt_gateway != 0, destination requires a nexthop gateway
Abstract the fetching of the proper nexthop value using a new
inline helper, rt_nexthop(), as suggested by Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Vijay Subramanian <subramanian.vijay@gmail.com>
They are always used in contexts where they can be reconstituted,
or where the finally resolved rt->rt_{src,dst} is semantically
equivalent.
Signed-off-by: David S. Miller <davem@davemloft.net>
The "noref" argument to ip_route_input_common() is now always ignored
because we do not cache routes, and in that case we must always grab
a reference to the resulting 'dst'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv4 routing cache is non-deterministic, performance wise, and is
subject to reasonably easy to launch denial of service attacks.
The routing cache works great for well behaved traffic, and the world
was a much friendlier place when the tradeoffs that led to the routing
cache's design were considered.
What it boils down to is that the performance of the routing cache is
a product of the traffic patterns seen by a system rather than being a
product of the contents of the routing tables. The former of which is
controllable by external entitites.
Even for "well behaved" legitimate traffic, high volume sites can see
hit rates in the routing cache of only ~%10.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a crash
tun_chr_close -> netdev_run_todo -> tun_free_netdev -> sk_release_kernel ->
sock_release -> iput(SOCK_INODE(sock))
introduced by commit 1ab5ecb90c
The problem is that this socket is embedded in struct tun_struct, it has
no inode, iput is called on invalid inode, which modifies invalid memory
and optionally causes a crash.
sock_release also decrements sockets_in_use, this causes a bug that
"sockets: used" field in /proc/*/net/sockstat keeps on decreasing when
creating and closing tun devices.
This patch introduces a flag SOCK_EXTERNALLY_ALLOCATED that instructs
sock_release to not free the inode and not decrement sockets_in_use,
fixing both memory corruption and sockets_in_use underflow.
It should be backported to 3.3 an 3.4 stabke.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces IFLA_NUM_TX_QUEUES and IFLA_NUM_RX_QUEUES by
which userspace can set number of rx and/or tx queues to be allocated
for newly created netdevice.
This overrides ops->get_num_[tr]x_queues()
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also cut out unused function parameters and possible err in return
value.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern TCP stack highly depends on tcp_write_timer() having a small
latency, but current implementation doesn't exactly meet the
expectations.
When a timer fires but finds the socket is owned by the user, it rearms
itself for an additional delay hoping next run will be more
successful.
tcp_write_timer() for example uses a 50ms delay for next try, and it
defeats many attempts to get predictable TCP behavior in term of
latencies.
Use the recently introduced tcp_release_cb(), so that the user owning
the socket will call various handlers right before socket release.
This will permit us to post a followup patch to address the
tcp_tso_should_defer() syndrome (some deferred packets have to wait
RTO timer to be transmitted, while cwnd should allow us to send them
sooner)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: John Heffner <johnwheffner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When/if sysctl_tcp_abc > 1, we expect to increase cwnd by 2 if the
received ACK acknowledges more than 2*MSS bytes, in tcp_slow_start()
Problem is this RFC 3465 statement is not correctly coded, as
the while () loop increases snd_cwnd one by one.
Add a new variable to avoid this off-by one error.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a missing roundup_pow_of_two(), since tcpmhash_entries is not
guaranteed to be a power of two.
Uses hash_32() instead of custom hash.
tcpmhash_entries should be an unsigned int.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Applied to a set of static inline functions in tcp_input.c
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull last minute Ceph fixes from Sage Weil:
"The important one fixes a bug in the socket failure handling behavior
that was turned up in some recent failure injection testing. The
other two are minor bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: endian bug in rbd_req_cb()
rbd: Fix ceph_snap_context size calculation
libceph: fix messenger retry
Fix again the diff value in rt_bind_exception
after collision of two latest patches, my original commit
actually fixed the same problem.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
In trusted networks, e.g., intranet, data-center, the client does not
need to use Fast Open cookie to mitigate DoS attacks. In cookie-less
mode, sendmsg() with MSG_FASTOPEN flag will send SYN-data regardless
of cookie availability.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On paths with firewalls dropping SYN with data or experimental TCP options,
Fast Open connections will have experience SYN timeout and bad performance.
The solution is to track such incidents in the cookie cache and disables
Fast Open temporarily.
Since only the original SYN includes data and/or Fast Open option, the
SYN-ACK has some tell-tale sign (tcp_rcv_fastopen_synack()) to detect
such drops. If a path has recurring Fast Open SYN drops, Fast Open is
disabled for 2^(recurring_losses) minutes starting from four minutes up to
roughly one and half day. sendmsg with MSG_FASTOPEN flag will succeed but
it behaves as connect() then write().
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sendmsg() (or sendto()) with MSG_FASTOPEN is a combo of connect(2)
and write(2). The application should replace connect() with it to
send data in the opening SYN packet.
For blocking socket, sendmsg() blocks until all the data are buffered
locally and the handshake is completed like connect() call. It
returns similar errno like connect() if the TCP handshake fails.
For non-blocking socket, it returns the number of bytes queued (and
transmitted in the SYN-data packet) if cookie is available. If cookie
is not available, it transmits a data-less SYN packet with Fast Open
cookie request option and returns -EINPROGRESS like connect().
Using MSG_FASTOPEN on connecting or connected socket will result in
simlar errno like repeating connect() calls. Therefore the application
should only use this flag on new sockets.
The buffer size of sendmsg() is independent of the MSS of the connection.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On receiving the SYN-ACK after SYN-data, the client needs to
a) update the cached MSS and cookie (if included in SYN-ACK)
b) retransmit the data not yet acknowledged by the SYN-ACK in the final ACK of
the handshake.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements sending SYN-data in tcp_connect(). The data is
from tcp_sendmsg() with flag MSG_FASTOPEN (implemented in a later patch).
The length of the cookie in tcp_fastopen_req, init'd to 0, controls the
type of the SYN. If the cookie is not cached (len==0), the host sends
data-less SYN with Fast Open cookie request option to solicit a cookie
from the remote. If cookie is not available (len > 0), the host sends
a SYN-data with Fast Open cookie option. If cookie length is negative,
the SYN will not include any Fast Open option (for fall back operations).
To deal with middleboxes that may drop SYN with data or experimental TCP
option, the SYN-data is only sent once. SYN retransmits do not include
data or Fast Open options. The connection will fall back to regular TCP
handshake.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With help from Eric Dumazet, add Fast Open metrics in tcp metrics cache.
The basic ones are MSS and the cookies. Later patch will cache more to
handle unfriendly middleboxes.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch impelements the common code for both the client and server.
1. TCP Fast Open option processing. Since Fast Open does not have an
option number assigned by IANA yet, it shares the experiment option
code 254 by implementing draft-ietf-tcpm-experimental-options
with a 16 bits magic number 0xF989. This enables global experiments
without clashing the scarce(2) experimental options available for TCP.
When the draft status becomes standard (maybe), the client should
switch to the new option number assigned while the server supports
both numbers for transistion.
2. The new sysctl tcp_fastopen
3. A place holder init function
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet II wrapper is only used by IPX protocol, may have once
been used by Appletalk but not currently. Therefore it makes sense to
move it to the IPX dust bin and drop the exports.
Build tested only.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v4_send_reset() and tcp_v4_send_ack() use a single socket
per network namespace.
This leads to bad behavior on multiqueue NICS, because many cpus
contend for the socket lock and once socket lock is acquired, extra
false sharing on various socket fields slow down the operations.
To better resist to attacks, we use a percpu socket. Each cpu can
run without contention, using appropriate memory (local node)
Additional features :
1) We also mirror the queue_mapping of the incoming skb, so that
answers use the same queue if possible.
2) Setting SOCK_USE_WRITE_QUEUE socket flag speedup sock_wfree()
3) We now limit the number of in-flight RST/ACK [1] packets
per cpu, instead of per namespace, and we honor the sysctl_wmem_default
limit dynamically. (Prior to this patch, sysctl_wmem_default value was
copied at boot time, so any further change would not affect tcp_sock
limit)
[1] These packets are only generated when no socket was matched for
the incoming packet.
Reported-by: Bill Sommerfeld <wsommerfeld@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use global seqlock for the nh_exceptions. Call
fnhe_oldest with the right hash chain. Correct the diff
value for dst_set_expires.
v2: after suggestions from Eric Dumazet:
* get rid of spin lock fnhe_lock, rearrange update_or_create_fnhe
* continue daddr search in rt_bind_exception
v3:
* remove the daddr check before seqlock in rt_bind_exception
* restart lookup in rt_bind_exception on detected seqlock change,
as suggested by David Miller
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings