Some broken ACPI tables might require quirks in the OS.
Introduce quirks field in struct acpi_gpio_mapping.
Propagate them to struct acpi_gpio_info for further use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACPI code supporting system transitions to sleep states uses
an internal blacklist to apply special handling to some machines
reported to behave incorrectly in some ways.
However, some entries of that blacklist cover problematic as well as
non-problematic systems, so give the users of the latter a chance to
ignore the blacklist and run their systems in the default way by
adding acpi_sleep=nobl to the kernel command line.
For example, that allows the users of Dell XPS13 9360 systems not
affected by the issue that caused the blacklist entry for this
machine to be added by commit 71630b7a83 (ACPI / PM: Blacklist Low
Power S0 Idle _DSM for Dell XPS13 9360) to use suspend-to-idle with
the Low Power S0 Idle _DSM interface which in principle should be
more energy-efficient than S3 on them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make the ACPI PM domain take DPM_FLAG_SMART_SUSPEND into account in
its system suspend callbacks.
[Note that the pm_runtime_suspended() check in acpi_dev_needs_resume()
is an optimization, because if is not passed, all of the subsequent
checks may be skipped and some of them are much more overhead in
general.]
Also use the observation that if the device is in runtime suspend
at the beginning of the "late" phase of a system-wide suspend-like
transition, its state cannot change going forward (runtime PM is
disabled for it at that time) until the transition is over and the
subsequent system-wide PM callbacks should be skipped for it (as
they generally assume the device to not be suspended), so add
checks for that in acpi_subsys_suspend_late/noirq() and
acpi_subsys_freeze_late/noirq().
Moreover, if acpi_subsys_resume_noirq() is called during the
subsequent system-wide resume transition and if the device was left
in runtime suspend previously, its runtime PM status needs to be
changed to "active" as it is going to be put into the full-power
state going forward, so add a check for that too in there.
In turn, if acpi_subsys_thaw_noirq() runs after the device has been
left in runtime suspend, the subsequent "thaw" callbacks need
to be skipped for it (as they may not work correctly with a
suspended device), so set the power.direct_complete flag for the
device then to make the PM core skip those callbacks.
On top of the above, make the analogous changes in the acpi_lpss
driver that uses the ACPI PM domain callbacks.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On top of a previous change getting rid of the PM QoS flag
PM_QOS_FLAG_REMOTE_WAKEUP, combine two ACPI device suspend routines,
acpi_dev_runtime_suspend() and acpi_dev_suspend_late(), into one,
acpi_dev_suspend(), to eliminate some code duplication.
It also avoids enabling wakeup for devices handled by the ACPI
LPSS middle layer on driver removal.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Add functionality to read LPIT table, which provides:
- Sysfs interface to read residency counters via
/sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
/sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Here the count "low_power_idle_cpu_residency_us" shows the time spent
by CPU package in low power state. This is read via MSR interface,
which points to MSR for PKG C10.
Here the count "low_power_idle_system_residency_us" show the count the
system was in low power state. This is read via MMIO interface. This
is mapped to SLP_S0 residency on modern Intel systems. This residency
is achieved only when CPU is in PKG C10 and all functional blocks are
in low power state.
It is possible that none of the above counters present or anyone of the
counter present or all counters present.
For example: On my Kabylake system both of the above counters present.
After suspend to idle these counts updated and prints:
6916179
6998564
This counter can be read by tools like turbostat to display. Or it can
be used to debug, if modern systems are reaching desired low power state.
- Provides an interface to read residency counter memory address
This address can be used to get the base address of PMC memory
mapped IO. This is utilized by intel_pmc_core driver to print
more debug information.
In addition, to avoid code duplication to read iomem, removed the read of
iomem from acpi_os_read_memory() in osl.c and made a common function
acpi_os_read_iomem(). This new function is used for reading iomem in
in both osl.c and acpi_lpit.c.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Notice that acpi_dev_runtime_resume() and acpi_dev_resume_early() are
actually literally identical after some more-or-less recent changes,
so rename acpi_dev_runtime_resume() to acpi_dev_resume(), use it
everywhere instead of acpi_dev_resume_early() and drop the latter.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
acpi_dev_pm_get_node() isn't used or implemented, so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Introduce fwnode operations for all of the separate types of
"firmware nodes" that can be handled by the device properties
framework and drop the type field from struct fwnode_handle
(Sakari Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references
to the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework
to the new UUID API (Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZrcHoAAoJEILEb/54YlRxVH4P/i7MVmWxZW1qosqt8NbI+kqu
rjxBiQ1YaPuwWiZk5LMRQWIr4Y52v+8uwoVAoQbpfkpQpxpUtIApqFGGHkOK091S
6wcwdAJv78m7dQGJZ96nQkBdw+qCUG+s9L3KMfXYiipwyG7bg4BVcs5jZcIqcZ4F
2xecG6DMn4ESwFbZyVULWyQh50tSBztaHEG6AU2T/07yXU3RNJmwAVVZzpHdtA80
mDbWcCFjcmhrpPa0Aq6MrSMjKso1zd8Es+xwYhXsIQpD1l0HhLLQ0X4veSPcPG4B
aSNEYuribpvZ2FIRti7H7gi/F+Arm9vPdc9WHbOPLOIF1z+GJKiqjBuxUrfXKPqG
v1W3f1bcApe9DfmC5z1wZBi2d7thQOzRFfc8WRrMybQ6z1MAqqe5PfAlgpMFmL22
8ZCzzXIBUsfUjVlwYBvgkKvpLioEl88otWGdhewWY6F+DZ8+vPyvrpi15P36Xgos
ijX89cvyfze3m5GW08hQ6DTOVvaFoMyucYfSo6/MBamw9fbUgiEgBfUAsQyb3sRU
8g1KrwkAX8KFmoocX/AVjvwVBaKNdYeJ9Gy6EItAPxNl+F1q6vjkO0r/VeSrO1KW
3GRqw5MZP35DD9IRo4DTAjwtNVkgIUjpG/hfB7l3PFdDxWfeiM5tf2zMExhT0nIR
h8s8mn61KZp0gpsE02FS
=0rnk
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework, make the framework use const fwnode arguments all over, add
a helper for the consolidated handling of node references and switch
over the framework to the new UUID API.
Specifics:
- Introduce fwnode operations for all of the separate types of
'firmware nodes' that can be handled by the device properties
framework and drop the type field from struct fwnode_handle (Sakari
Ailus, Arnd Bergmann).
- Make the device properties framework use const fwnode arguments
where possible (Sakari Ailus).
- Add a helper for the consolidated handling of node references to
the device properties framework (Sakari Ailus).
- Switch over the ACPI part of the device properties framework to the
new UUID API (Andy Shevchenko)"
* tag 'devprop-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: device property: Switch to use new generic UUID API
device property: export irqchip_fwnode_ops
device property: Introduce fwnode_property_get_reference_args
device property: Constify fwnode property API
device property: Constify argument to pset fwnode backend
ACPI: Constify internal fwnode arguments
ACPI: Constify acpi_bus helper functions, switch to macros
ACPI: Prepare for constifying acpi_get_next_subnode() fwnode argument
device property: Get rid of struct fwnode_handle type field
ACPI: Use IS_ERR_OR_NULL() instead of non-NULL check in is_acpi_data_node()
* acpi-sysfs:
ACPI / sysfs: Extend ACPI sysfs to provide access to boot error region
* acpi-apei:
ACPI / APEI: Suppress message if HEST not present
ACPI, APEI, EINJ: Subtract any matching Register Region from Trigger resources
ACPI: APEI: fix the wrong iteration of generic error status block
ACPI: APEI: Enable APEI multiple GHES source to share a single external IRQ
* acpi-blacklist:
intel_pstate: convert to use acpi_match_platform_list()
ACPI / blacklist: add acpi_match_platform_list()
* acpi-ec:
ACPI / EC: Clean up EC GPE mask flag
ACPI: EC: Fix possible issues related to EC initialization order
* acpi-dma:
ACPI/IORT: Add IORT named component memory address limits
ACPI: Make acpi_dma_configure() DMA regions aware
ACPI: Introduce DMA ranges parsing
ACPI: Make acpi_dev_get_resources() method agnostic
* acpi-processor:
ACPI / processor: make function acpi_processor_check_duplicates() static
ACPI: processor: use dev_dbg() instead of dev_warn() when CPPC probe failed
* acpi-cppc:
mailbox: pcc: Drop uninformative output during boot
ACPI OEM ID / OEM Table ID / Revision can be used to identify
a platform based on ACPI firmware info. acpi_blacklisted(),
intel_pstate_platform_pwr_mgmt_exists(), and some other funcs,
have been using similar check to detect a list of platforms
that require special handlings.
Move the platform check in acpi_blacklisted() to a new common
utility function, acpi_match_platform_list(), so that other
drivers do not have to implement their own version.
There is no change in functionality.
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some devices have limited addressing capabilities and cannot
reference the whole memory address space while carrying out DMA
operations (eg some devices with bus address bits range smaller than
system bus - which prevents them from using bus addresses that are
otherwise valid for the system).
The ACPI _DMA object allows bus devices to define the DMA window that is
actually addressable by devices that sit upstream the bus, therefore
providing a means to parse and initialize the devices DMA masks and
addressable DMA range size.
By relying on the generic ACPI kernel layer to retrieve and parse
resources, introduce ACPI core code to parse the _DMA object.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The work-around for Qualcomm Technologies QDF2400 Erratum 44 hinges on a
global variable defined in the pl011 driver. The ACPI SPCR parsing code
determines whether the work-around is needed, and if so, it changes the
console name from "pl011" to "qdf2400_e44". The expectation is that
the pl011 driver will implement the work-around when it sees the console
name. The global variable qdf2400_e44_present is set when that happens.
The problem is that work-around needs to be enabled when the pl011
driver probes, not when the console name is queried. However, sbsa_probe()
is called before pl011_console_match(). The work-around appeared to work
previously because the default console on QDF2400 platforms was always
ttyAMA1. The first time sbsa_probe() is called (for ttyAMA0),
qdf2400_e44_present is still false. Then pl011_console_match() is called,
and it sets qdf2400_e44_present to true. All subsequent calls to
sbsa_probe() enable the work-around.
The solution is to move the global variable into spcr.c and let the
pl011 driver query it during probe time. This works because all QDF2400
platforms require SPCR, so parse_spcr() will always be called.
pl011_console_match still checks for the "qdf2400_e44" console name,
but it doesn't do anything else special.
Fixes: 5a0722b898 ("tty: pl011: use "qdf2400_e44" as the earlycon name for QDF2400 E44")
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse complains about wrong address space used in __acpi_map_table()
and in __acpi_unmap_table().
arch/x86/kernel/acpi/boot.c:127:29: warning: incorrect type in return expression (different address spaces)
arch/x86/kernel/acpi/boot.c:127:29: expected char *
arch/x86/kernel/acpi/boot.c:127:29: got void [noderef] <asn:2>*
arch/x86/kernel/acpi/boot.c:135:23: warning: incorrect type in argument 1 (different address spaces)
arch/x86/kernel/acpi/boot.c:135:23: expected void [noderef] <asn:2>*addr
arch/x86/kernel/acpi/boot.c:135:23: got char *map
Correct address space to be in align of type of returned and passed
parameter.
Reviewed-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make fwnode arguments to the fwnode property API const.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Constify internal ACPI fwnode arguments in preparation for the same in
fwnode API.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Instead of relying on the struct fwnode_handle type field, define
fwnode_operations structs for all separate types of fwnodes. To find out
the type, compare to the ops field to relevant ops structs.
This change has two benefits:
1. it avoids adding the type field to each and every instance of struct
fwnode_handle, thus saving memory and
2. makes the ops field the single factor that defines both the types of
the fwnode as well as defines the implementation of its operations,
decreasing the possibility of bugs when developing code dealing with
fwnode internals.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework
(ACPI, DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJZY/OvAAoJEILEb/54YlRx8NYP/3hL9jK8yBgDEVkoNnRDN7Xj
gefqm++3YO6wy8pfuACfNal2lJRFat5NDWdkBUsFA7LAfaLYe6jkIZ8YW+XTcHq7
H8dmFiDjfhVa4/urS6DTHmHqPyWLh4ayjTfwRP0yy2aW2XpXe1WNAgilLStu96iH
OU44HY5FQCQipnIIcuJZpJwH51AMyJIuAV5rQJySoIuDyULRKmVQ8G/xCAfhzHCH
tLcQHZnnYUdSCi29JwCu2RKKI6ta2o68EYmi1wxjvMEs2z27KVltCu+5Y9mpOIwl
DU+X8hAmepzd5aJxpR69hzM+dr71+0feUOklEU+r0DJzlmdDzTK8NyEPW2Ysh0aa
0SsdtgoRWv+kq0FuzL26fpa01WOcWB8N5uDp4XUZKFCriRmBk2HNc1KRoPtvILm2
2ISOqdIPe2/fC/FOYT0mKcFXaezkONpdbZoUqWGKFw0OWkgc5Vesl7L0LlilLCS6
XpHP/ISJBDfmIwjgaDjZIV1G6PkyaKu4tPkn9NsN+ztbH02dpTodIB0qDJSimyPX
cYwuDBn6NpKhk/l8b7lNMLxX8xK5EpQKw90av3LFYwZcGpyBzsoqciLONPSqF+1p
jHDK4yaV+Ddwo3q5368x+eXX/Y9hfDewikoAuAUG3y0cMzuwKwFZ7MRkfl1Azbcc
CLNeBd8YXBUnbzDMYaNB
=EcrF
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These mostly rearrange the device properties core code and add a few
helper functions to it as a foundation for future work.
Specifics:
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework (ACPI,
DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham)"
* tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add fwnode_graph_get_port_parent
device property: Add FW type agnostic fwnode_graph_get_remote_node
device property: Introduce fwnode_device_is_available()
device property: Move fwnode graph ops to firmware specific locations
device property: Move FW type specific functionality to FW specific files
ACPI: Constify argument to acpi_device_is_present()
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO line
may loose its state during suspend/resume of the system to save
power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes.
-----BEGIN PGP SIGNATURE-----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=TpW1
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.13 series.
Some administrativa:
I have a slew of 8250 serial patches and the new IOT2040 serial+GPIO
driver coming in through this tree, along with a whole bunch of Exar
8250 fixes. These are ACKed by Greg and also hit drivers/platform/*
where they are ACKed by Andy Shevchenko.
Speaking about drivers/platform/* there is also a bunch of ACPI stuff
coming through that route, again ACKed by Andy.
The MCP23S08 changes are coming in here as well. You already have the
commits in your tree, so this is just a result of sharing an immutable
branch between pin control and GPIO.
Core:
- Export add/remove for lookup tables so that modules can export GPIO
descriptor tables.
- Handle GPIO sleep states: it is now possible to flag that a GPIO
line may loose its state during suspend/resume of the system to
save power. This is used in the Wolfson Micro Arizona driver.
- ACPI-based GPIO was tightened up a lot around the edges.
- Use bitmap_fill() to speed up a loop.
New drivers:
- Exar XRA1403 SPI-based GPIO.
- MVEBU driver now supports Armada 7K and 8K.
- LP87565 PMIC GPIO.
- Renesas R-CAR R8A7743 (RZ/G1M).
- The new IOT2040 8250 serial/GPIO also comes in through this
changeset.
Substantial driver changes:
- Seriously fix the Exar 8250 GPIO portions to work.
- The MCP23S08 was moved out to a pin control driver.
- Convert MEVEBU to use regmap for register access.
- Drop Vulcan support from the Broadcom driver.
- Serious cleanup and improvement of the mockup driver, giving us a
better test coverage.
Misc:
- Lots of janitorial clean up.
- A bunch of documentation fixes"
* tag 'gpio-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (70 commits)
serial: exar: Add support for IOT2040 device
gpio-exar/8250-exar: Make set of exported GPIOs configurable
platform: Accept const properties
serial: exar: Factor out platform hooks
gpio-exar/8250-exar: Rearrange gpiochip parenthood
gpio: exar: Fix iomap request
gpio-exar/8250-exar: Do not even instantiate a GPIO device for Commtech cards
serial: uapi: Add support for bus termination
gpio: rcar: Add R8A7743 (RZ/G1M) support
gpio: gpio-wcove: Fix GPIO control register offset calculation
gpio: lp87565: Add support for GPIO
gpio: dwapb: fix missing first irq for edgeboth irq type
MAINTAINERS: Take maintainership for GPIO ACPI support
gpio: exar: Fix reading of directions and values
gpio: exar: Allocate resources on behalf of the platform device
gpio-exar/8250-exar: Fix passing in of parent PCI device
gpio: mockup: use devm_kcalloc() where applicable
gpio: mockup: add myself as author
gpio: mockup: improve the error message
gpio: mockup: don't return magic numbers from probe()
...
The device and fwnode property API supports Devicetree, ACPI and pset
properties. The implementation of this functionality for each firmware
type was embedded in the fwnode property core. Move it out to firmware
type specific locations, making it easier to maintain.
Depends-on: ("of: Move OF property and graph API from base.c to property.c")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Without this the build will fail for !CONFIG_ACPI builds on x86.
Fixes: 94116f81 ("ACPI: Switch to use generic guid_t in acpi_evaluate_dsm()")
Signed-off-by: Christoph Hellwig <hch@lst.de>
acpi_evaluate_dsm() and friends take a pointer to a raw buffer of 16
bytes. Instead we convert them to use guid_t type. At the same time we
convert current users.
acpi_str_to_uuid() becomes useless after the conversion and it's safe to
get rid of it.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Cc: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Yisen Zhuang <yisen.zhuang@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are new types and helpers that are supposed to be used in new code.
As a preparation to get rid of legacy types and API functions do
the conversion here.
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The helper does retrieve pointer to struct acpi_resource_gpio from
struct acpi_resource if it represents GpioInt() resource.
It will be used by PNP code later on.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This includes:
* Some code optimizations for the Intel VT-d driver
* Code to switch off a previously enabled Intel IOMMU
* Support for 'struct iommu_device' for OMAP, Rockchip and
Mediatek IOMMUs
* Some header optimizations for IOMMU core code headers and a
few fixes that became necessary in other parts of the kernel
because of that
* ACPI/IORT updates and fixes
* Some Exynos IOMMU optimizations
* Code updates for the IOMMU dma-api code to bring it closer to
use per-cpu iova caches
* New command-line option to set default domain type allocated
by the iommu core code
* Another command line option to allow the Intel IOMMU switched
off in a tboot environment
* ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using
an IDENTITY domain in conjunction with DMA ops, Support for
SMR masking, Support for 16-bit ASIDs (was previously broken)
* Various other small fixes and improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3aE8
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- code optimizations for the Intel VT-d driver
- ability to switch off a previously enabled Intel IOMMU
- support for 'struct iommu_device' for OMAP, Rockchip and Mediatek
IOMMUs
- header optimizations for IOMMU core code headers and a few fixes that
became necessary in other parts of the kernel because of that
- ACPI/IORT updates and fixes
- Exynos IOMMU optimizations
- updates for the IOMMU dma-api code to bring it closer to use per-cpu
iova caches
- new command-line option to set default domain type allocated by the
iommu core code
- another command line option to allow the Intel IOMMU switched off in
a tboot environment
- ARM/SMMU: TLB sync optimisations for SMMUv2, Support for using an
IDENTITY domain in conjunction with DMA ops, Support for SMR masking,
Support for 16-bit ASIDs (was previously broken)
- various other small fixes and improvements
* tag 'iommu-updates-v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (63 commits)
soc/qbman: Move dma-mapping.h include to qman_priv.h
soc/qbman: Fix implicit header dependency now causing build fails
iommu: Remove trace-events include from iommu.h
iommu: Remove pci.h include from trace/events/iommu.h
arm: dma-mapping: Don't override dma_ops in arch_setup_dma_ops()
ACPI/IORT: Fix CONFIG_IOMMU_API dependency
iommu/vt-d: Don't print the failure message when booting non-kdump kernel
iommu: Move report_iommu_fault() to iommu.c
iommu: Include device.h in iommu.h
x86, iommu/vt-d: Add an option to disable Intel IOMMU force on
iommu/arm-smmu: Return IOVA in iova_to_phys when SMMU is bypassed
iommu/arm-smmu: Correct sid to mask
iommu/amd: Fix incorrect error handling in amd_iommu_bind_pasid()
iommu: Make iommu_bus_notifier return NOTIFY_DONE rather than error code
omap3isp: Remove iommu_group related code
iommu/omap: Add iommu-group support
iommu/omap: Make use of 'struct iommu_device'
iommu/omap: Store iommu_dev pointer in arch_data
iommu/omap: Move data structures to omap-iommu.h
iommu/omap: Drop legacy-style device support
...
Core changes
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources.
I have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements
- A whole slew of drivers have their spinlocks chaned to raw spinlocks
as they provide irqchips, and thus we are progressing on realtime
compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot.
-----BEGIN PGP SIGNATURE-----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=DGPb
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.12 kernel cycle.
Core changes:
- Return NULL from gpiod_get_optional() when GPIOLIB is disabled.
This was a much discussed change. It affects use cases where people
write drivers that might or might not be using GPIO resources. I
have decided that this is the lesser evil right now.
- Make gpiod_count() behave consistently across different hardware
descriptions.
- Fix the syntax around open drain/open source to not infer active
high/low semantics.
New drivers:
- A new single-register fixed-direction framework driver for hardware
that have lines controlled by a single register that just work in
one direction (out or in), including IRQ support.
- Support the Fintek F71889A GPIO SuperIO controller.
- Support the National NI 169445 MMIO GPIO.
- Support for the X-Gene derivative of the DWC GPIO controller
- Support for the Rohm BD9571MWV-M PMIC GPIO controller.
- Refactor the Gemini GPIO driver to a generic Faraday FTGPIO driver
and replace both the Gemini and the Moxa ART custom drivers with
this driver.
Driver improvements:
- A whole slew of drivers have their spinlocks chaned to raw
spinlocks as they provide irqchips, and thus we are progressing on
realtime compliance.
- Use devm_irq_alloc_descs() in a slew of drivers, getting managed
resources.
- Support for the embedded PWM controller inside the MVEBU driver.
- Debounce, open source and open drain support for the Aspeed driver.
- Misc smaller fixes like spelling and syntax and whatnot"
* tag 'gpio-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: f7188x: Add a missing break
gpio: omap: return error if requested debounce time is not possible
gpio: Add ROHM BD9571MWV-M PMIC GPIO driver
gpio: gpio-wcove: fix GPIO IRQ status mask
gpio: DT bindings, move tca9554 from pcf857x to pca953x
gpio: move tca9554 from pcf857x to pca953x
gpio: arizona: Correct check whether the pin is an input
gpio: Add XRA1403 DTS binding documentation
dt-bindings: add exar to vendor prefixes list
gpio: gpio-wcove: fix irq pending status bit width
gpio: dwapb: use dwapb_read instead of readl_relaxed
gpio: aspeed: Add open-source and open-drain support
gpio: aspeed: Add debounce support
gpio: aspeed: dt: Add optional clocks property
gpio: aspeed: dt: Fix description alignment in bindings document
gpio: mvebu: Add limited PWM support
gpio: Use unsigned int for interrupt numbers
gpio: f7188x: Add F71889A GPIO support.
gpio: core: Decouple open drain/source flag with active low/high
gpio: arizona: Correct handling for reading input GPIOs
...
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties
and extend the generic device properties framework to make it
more suitable for the handling of ports and endpoints (Sakari
Ailus).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Ihme
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull generic device properties framework updates from Rafael Wysocki:
"These add support for the ports and endpoints concepts, based on the
existing DT support for them, to the generic device properties
framework and update the ACPI _DSD properties code to recognize ports
and endpoints accordingly.
Specifics:
- Extend the ACPI _DSD properties code and the generic device
properties framework to support the concept of remote endponts
(Mika Westerberg, Sakari Ailus).
- Document the support for ports and endpoints in _DSD properties and
extend the generic device properties framework to make it more
suitable for the handling of ports and endpoints (Sakari Ailus)"
* tag 'devprop-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Read strings using string array reading functions
device property: fwnode_property_read_string_array() returns nr of strings
device property: Fix reading pset strings using array access functions
device property: fwnode_property_read_string_array() may return -EILSEQ
ACPI / DSD: Document references, ports and endpoints
device property: Add fwnode_get_next_parent()
device property: Add support for fwnode endpoints
device property: Make dev_fwnode() public
of: Add of_fwnode_handle() to convert device nodes to fwnode_handle
device property: Add fwnode_handle_get()
device property: Add support for remote endpoints
ACPI / property: Add support for remote endpoints
device property: Add fwnode_get_named_child_node()
ACPI / property: Add fwnode_get_next_child_node()
device property: Add fwnode_get_parent()
ACPI / property: Add possiblity to retrieve parent firmware node
This is an equivalent to the DT's handling of the iommu master's probe
with deferred probing when the corrsponding iommu is not probed yet.
The lack of a registered IOMMU can be caused by the lack of a driver for
the IOMMU, the IOMMU device probe not having been performed yet, having
been deferred, or having failed.
The first case occurs when the firmware describes the bus master and
IOMMU topology correctly but no device driver exists for the IOMMU yet
or the device driver has not been compiled in. Return NULL, the caller
will configure the device without an IOMMU.
The second and third cases are handled by deferring the probe of the bus
master device which will eventually get reprobed after the IOMMU.
The last case is currently handled by deferring the probe of the bus
master device as well. A mechanism to either configure the bus master
device without an IOMMU or to fail the bus master device probe depending
on whether the IOMMU is optional or mandatory would be a good
enhancement.
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
[Lorenzo: Added fixes for dma_coherent_mask overflow, acpi_dma_configure
called multiple times for same device]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
acpi_dev_found just iterates over all ACPI-ids and sees if one matches.
This means that it will return true for devices which are in the DSDT
but disabled (their _STA method returns 0).
For some drivers it is useful to be able to check if a certain HID
is not only present in the namespace, but also actually present as in
acpi_device_is_present() will return true for the device. For example
because if a certain device is present then the driver will want to use
an extcon or IIO ADC channel provided by that device.
This commit adds a new acpi_dev_present helper which drivers can use
to this end.
Like acpi_dev_found, acpi_dev_present take a HID as argument, but
it also has 2 extra optional arguments to only check for an ACPI
device with a specific UID and/or HRV value. This makes it more
generic and allows it to replace custom code doing similar checks
in several places.
Arguably acpi_dev_present is what acpi_dev_found should have been, but
there are too many users to just change acpi_dev_found without the risk
of breaking something.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms booting with ACPI, architected memory-mapped timers'
configuration data is provided by firmware through the ACPI GTDT
static table.
The clocksource architected timer kernel driver requires a firmware
interface to collect timer configuration and configure its driver.
this infrastructure is present for device tree systems, but it is
missing on systems booting with ACPI.
Implement the kernel infrastructure required to parse the static
ACPI GTDT table so that the architected timer clocksource driver can
make use of it on systems booting with ACPI, therefore enabling
the corresponding timers configuration.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
[Mark: restructure error handling]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
This patch adds support for parsing arch timer info in GTDT,
provides some kernel APIs to parse all the PPIs and
always-on info in GTDT and export them.
By this driver, we can simplify arm_arch_timer drivers, and
separate the ACPI GTDT knowledge from it.
Signed-off-by: Fu Wei <fu.wei@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Function acpi_parse_entries() is not used any more and if necessary,
acpi_table_parse_entries() can be used instead of it, so drop it.
Signed-off-by: Baoquan He <bhe@redhat.com>
[ rjw: Subject / changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
DT has had concept of remote endpoints for some time already. It makes
possible to reference another firmware node through a property called
remote-endpoint. This is already used by some subsystems like v4l2 for
parsing hardware properties related to camera.
This patch adds ACPI support for remote endpoints utilizing _DSD
hierarchical data extensions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI _DSD hierarchical data extension makes it possible to have
hierarchies deeper than one level in similar way than DT allows. These
"subsubnodes" have not been accessible because device property
implementation only provides device_get_next_child_node() that is limited
to direct descendants of a device.
We need this ability in order support things like remote endpoints
currently supported in DT with of_graph_* APIs.
Modify acpi_get_next_subnode() to accept fwnode handle instead and update
callers accordingly. Also add a new function fwnode_get_next_child_node()
that works directly with fwnodes and modify device_get_next_child_node() to
call it directly. While there add a macro fwnode_for_each_child_node()
analogous to the current device_for_each_child_node() but it works with
fwnodes instead of devices.
Link: http://www.uefi.org/sites/default/files/resources/_DSD-hierarchical-data-extension-UUID-v1.pdf
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes it is useful to be able to navigate firmware node hierarchy
upwards toward parent nodes. ACPI device nodes are pretty much already
supported because ACPICA provides acpi_get_parent(). ACPI data nodes,
however, are all below the same parent ACPI device. Their hierarchy is
created by "linking" each other using references in the value field.
Add parent pointer to the parent data node while we create them so it is
easy to navigate the hierarchy backwards. We use this parent pointer in a
new function acpi_node_get_parent() that is able to extract parent of both
ACPI firmware node types.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce device managed variant of acpi_dev_add_driver_gpios() and its
counterpart acpi_dev_remove_driver_gpios().
The functions in most cases are used in driver's ->probe() and
->remove() callbacks, that's why it's useful to have managed variant of
them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The check for duplicate processor ids happens at boot time based on the
ACPI table contents, but the final sanity checks for a processor happen
at hotplug time.
At hotplug time, where the physical information is available, which might
differ from the ACPI table information, a check for duplicate processor
ids is missing.
Add it to the hotplug checks and rename the function so it better
reflects its purpose.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: guzheng1@huawei.com
Cc: izumi.taku@jp.fujitsu.com
Cc: lenb@kernel.org
Link: http://lkml.kernel.org/r/1488528147-2279-6-git-send-email-douly.fnst@cn.fujitsu.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Revert: dc6db24d24 ("x86/acpi: Set persistent cpuid <-> nodeid mapping when booting")
The mapping of "cpuid <-> nodeid" is established at boot time via ACPI
tables to keep associations of workqueues and other node related items
consistent across cpu hotplug.
But, ACPI tables are unreliable and failures with that boot time mapping
have been reported on machines where the ACPI table and the physical
information which is retrieved at actual hotplug is inconsistent.
Revert the mapping implementation so it can be replaced with a less error
prone approach.
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: guzheng1@huawei.com
Cc: izumi.taku@jp.fujitsu.com
Cc: lenb@kernel.org
Link: http://lkml.kernel.org/r/1488528147-2279-2-git-send-email-douly.fnst@cn.fujitsu.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
* Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng).
* ACPI resources handling fix related to invalid resource
descriptors (Bob Moore).
* Fix to enable implicit result conversion for several ASL
library functions (Bob Moore).
* Support for method invocations as target operands in AML
(Bob Moore).
* Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore).
* Utilities updates (Bob Moore, Lv Zheng).
* Disassembler/debugger updates (David Box, Lv Zheng).
* Build fixes (Colin Ian King, Lv Zheng).
* Update of copyright notices in all files (Bob Moore).
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan).
- Fixes for the ACPI EC and button drivers (Lv Zheng).
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov).
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui).
- Message formatting fix for the ACPI APEI code (Colin Ian King).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=aJJ+
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20170119, which among other things updates copyright notices in all of
the ACPICA files, fix a couple of issues in the ACPI EC and button
drivers, fix modalias handling for non-discoverable devices with
DT-compatible identification strings, add a suspend quirk for one
platform and fix a message in the APEI code.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20170119 including:
+ Fixes related to the handling of the bit width and bit offset
fields in Generic Address Structure (Lv Zheng)
+ ACPI resources handling fix related to invalid resource
descriptors (Bob Moore)
+ Fix to enable implicit result conversion for several ASL library
functions (Bob Moore)
+ Support for method invocations as target operands in AML (Bob
Moore)
+ Fix to use a correct operand type for DeRefOf() in some
situations (Bob Moore)
+ Utilities updates (Bob Moore, Lv Zheng)
+ Disassembler/debugger updates (David Box, Lv Zheng)
+ Build fixes (Colin Ian King, Lv Zheng)
+ Update of copyright notices in all files (Bob Moore)
- Fix for modalias handling for SPI and I2C devices with
DT-compatible identification strings (Dan O'Donovan)
- Fixes for the ACPI EC and button drivers (Lv Zheng)
- ACPI processor handling fix related to CPU hotplug (online/offline)
on x86 (Vitaly Kuznetsov)
- Suspend quirk to save/restore NVS memory over S3 transitions for
Lenovo G50-45 (Zhang Rui)
- Message formatting fix for the ACPI APEI code (Colin Ian King)"
* tag 'acpi-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPICA: Update version to 20170119
ACPICA: Tools: Update common signon, remove compilation bit width
ACPICA: Source tree: Update copyright notices to 2017
ACPICA: Linuxize: Restore and fix Intel compiler build
x86/ACPI: keep x86_cpu_to_acpiid mapping valid on CPU hotplug
spi: acpi: Initialize modalias from of_compatible
i2c: acpi: Initialize info.type from of_compatible
ACPI / bus: Introduce acpi_of_modalias() equiv of of_modalias_node()
ACPI: save NVS memory for Lenovo G50-45
ACPI, APEI, EINJ: fix malformed newline escape
ACPI / button: Remove lid_init_state=method mode
ACPI / button: Change default behavior to lid_init_state=open
ACPI / EC: Use busy polling mode when GPE is not enabled
ACPI / EC: Remove old CLEAR_ON_RESUME quirk
ACPICA: Update version to 20161222
ACPICA: Parser: Update parse info table for some operators
ACPICA: Fix a problem with recent extra support for control method invocations
ACPICA: Parser: Allow method invocations as target operands
ACPICA: Fix for implicit result conversion for the ToXXX functions
ACPICA: Resources: Not a valid resource if buffer length too long
..
We may or may not have all possible CPUs in MADT on boot but in any
case we're overwriting x86_cpu_to_acpiid mapping with U32_MAX when
acpi_register_lapic() is called again on the CPU hotplug path:
acpi_processor_hotadd_init()
-> acpi_map_cpu()
-> acpi_register_lapic()
As we have the required acpi_id information in acpi_processor_hotadd_init()
propagate it to acpi_map_cpu() to always keep x86_cpu_to_acpiid
mapping valid.
Reported-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
ACPI extended IRQ resources may contain a ResourceSource to specify
an alternate interrupt controller. Introduce acpi_irq_get and use it
to implement ResourceSource/IRQ domain mapping.
The new API is similar to of_irq_get and allows re-initialization
of a platform resource from the ACPI extended IRQ resource, and
provides proper behavior for probe deferral when the domain is not
yet present when called.
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Agustin Vega-Frias <agustinv@codeaurora.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ut0k
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"PCI changes:
- add support for PCI on ARM64 boxes with ACPI. We already had this
for theoretical spec-compliant hardware; now we're adding quirks
for the actual hardware (Cavium, HiSilicon, Qualcomm, X-Gene)
- add runtime PM support for hotplug ports
- enable runtime suspend for Intel UHCI that uses platform-specific
wakeup signaling
- add yet another host bridge registration interface. We hope this is
extensible enough to subsume the others
- expose device revision in sysfs for DRM
- to avoid device conflicts, make sure any VF BAR updates are done
before enabling the VF
- avoid unnecessary link retrains for ASPM
- allow INTx masking on Mellanox devices that support it
- allow access to non-standard VPD for Chelsio devices
- update Broadcom iProc support for PAXB v2, PAXC v2, inbound DMA,
etc
- update Rockchip support for max-link-speed
- add NVIDIA Tegra210 support
- add Layerscape LS1046a support
- update R-Car compatibility strings
- add Qualcomm MSM8996 support
- remove some uninformative bootup messages"
* tag 'pci-v4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (115 commits)
PCI: Enable access to non-standard VPD for Chelsio devices (cxgb3)
PCI: Expand "VPD access disabled" quirk message
PCI: pciehp: Remove loading message
PCI: hotplug: Remove hotplug core message
PCI: Remove service driver load/unload messages
PCI/AER: Log AER IRQ when claiming Root Port
PCI/AER: Log errors with PCI device, not PCIe service device
PCI/AER: Remove unused version macros
PCI/PME: Log PME IRQ when claiming Root Port
PCI/PME: Drop unused support for PMEs from Root Complex Event Collectors
PCI: Move config space size macros to pci_regs.h
x86/platform/intel-mid: Constify mid_pci_platform_pm
PCI/ASPM: Don't retrain link if ASPM not possible
PCI: iproc: Skip check for legacy IRQ on PAXC buses
PCI: pciehp: Leave power indicator on when enabling already-enabled slot
PCI: pciehp: Prioritize data-link event over presence detect
PCI: rcar: Add gen3 fallback compatibility string for pcie-rcar
PCI: rcar: Use gen2 fallback compatibility last
PCI: rcar-gen2: Use gen2 fallback compatibility last
PCI: rockchip: Move the deassert of pm/aclk/pclk after phy_init()
..
These changes include:
* Support for the ACPI IORT table on ARM systems and patches to
make the ARM-SMMU driver make use of it
* Conversion of the Exynos IOMMU driver to device dependency
links and implementation of runtime pm support based on that
conversion
* Update the Mediatek IOMMU driver to use the new
struct device->iommu_fwspec member
* Implementation of dma_map/unmap_resource in the generic ARM
dma-iommu layer
* A number of smaller fixes and improvements all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EYLL
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"These changes include:
- support for the ACPI IORT table on ARM systems and patches to make
the ARM-SMMU driver make use of it
- conversion of the Exynos IOMMU driver to device dependency links
and implementation of runtime pm support based on that conversion
- update the Mediatek IOMMU driver to use the new struct
device->iommu_fwspec member
- implementation of dma_map/unmap_resource in the generic ARM
dma-iommu layer
- a number of smaller fixes and improvements all over the place"
* tag 'iommu-updates-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (44 commits)
ACPI/IORT: Make dma masks set-up IORT specific
iommu/amd: Missing error code in amd_iommu_init_device()
iommu/s390: Drop duplicate header pci.h
ACPI/IORT: Introduce iort_iommu_configure
ACPI/IORT: Add single mapping function
ACPI/IORT: Replace rid map type with type mask
iommu/arm-smmu: Add IORT configuration
iommu/arm-smmu: Split probe functions into DT/generic portions
iommu/arm-smmu-v3: Add IORT configuration
iommu/arm-smmu-v3: Split probe functions into DT/generic portions
ACPI/IORT: Add support for ARM SMMU platform devices creation
ACPI/IORT: Add node match function
ACPI: Implement acpi_dma_configure
iommu/arm-smmu-v3: Convert struct device of_node to fwnode usage
iommu/arm-smmu: Convert struct device of_node to fwnode usage
iommu: Make of_iommu_set/get_ops() DT agnostic
ACPI/IORT: Add support for IOMMU fwnode registration
ACPI/IORT: Introduce linker section for IORT entries probing
ACPI: Add FWNODE_ACPI_STATIC fwnode type
iommu/arm-smmu: Set SMTNMB_TLBEN in ACR to enable caching of bypass entries
...
- ACPICA update including upstream revision 20160930 and several
commits beyond it (Bob Moore, Lv Zheng).
- Initial support for ACPI APEI on ARM64 (Tomasz Nowicki).
- New document describing the handling of _OSI and _REV in Linux
(Len Brown).
- New document describing the usage rules for _DSD properties
(Rafael Wysocki).
- Update of the ACPI properties-parsing code to reflect recent
changes in the (external) documentation it is based on (Rafael
Wysocki).
- Updates of the ACPI LPSS and ACPI APD SoC drivers for additional
hardware support (Andy Shevchenko, Nehal Shah).
- New blacklist entries for _REV and video handling (Alex Hung,
Hans de Goede, Michael Pobega).
- ACPI battery driver fix to fall back to _BIF if _BIX fails (Dave
Lambley).
- NMI notifications handling fix for APEI (Prarit Bhargava).
- Error code path fix for the ACPI CPPC library (Dan Carpenter).
- Assorted cleanups (Andy Shevchenko, Longpeng Mike).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Nzrb
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"The ACPICA code in the kernel gets updated as usual (included is
upstream revision 20160930 and a few commits from the next one, with
the rest waiting for an issue discovered in linux-next to be
addressed) which brings in a couple of fixes and cleanups
On top of that initial support for APEI on ARM64 is added, two new
pieces of documentation are introduced, the properties-parsing code is
updated to follow changes in the (external) documentation it is based
on and there are a few updates of SoC drivers, some new blacklist
entries, plus some assorted fixes and cleanups
Specifics:
- ACPICA update including upstream revision 20160930 and several
commits beyond it (Bob Moore, Lv Zheng)
- Initial support for ACPI APEI on ARM64 (Tomasz Nowicki)
- New document describing the handling of _OSI and _REV in Linux (Len
Brown)
- New document describing the usage rules for _DSD properties (Rafael
Wysocki)
- Update of the ACPI properties-parsing code to reflect recent
changes in the (external) documentation it is based on (Rafael
Wysocki)
- Updates of the ACPI LPSS and ACPI APD SoC drivers for additional
hardware support (Andy Shevchenko, Nehal Shah)
- New blacklist entries for _REV and video handling (Alex Hung, Hans
de Goede, Michael Pobega)
- ACPI battery driver fix to fall back to _BIF if _BIX fails (Dave
Lambley)
- NMI notifications handling fix for APEI (Prarit Bhargava)
- Error code path fix for the ACPI CPPC library (Dan Carpenter)
- Assorted cleanups (Andy Shevchenko, Longpeng Mike)"
* tag 'acpi-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (31 commits)
ACPICA: Utilities: Add new decode function for parser values
ACPI / osl: Refactor acpi_os_get_root_pointer() to drop 'else':s
ACPI / osl: Propagate actual error code for kstrtoul()
ACPI / property: Document usage rules for _DSD properties
ACPI: Document _OSI and _REV for Linux BIOS writers
ACPI / APEI / ARM64: APEI initial support for ARM64
ACPI / APEI: Fix NMI notification handling
ACPICA: Tables: Add an error message complaining driver bugs
ACPICA: Tables: Add acpi_tb_unload_table()
ACPICA: Tables: Cleanup acpi_tb_install_and_load_table()
ACPICA: Events: Fix acpi_ev_initialize_region() return value
ACPICA: Back port of "ACPICA: Dispatcher: Tune interpreter lock around AcpiEvInitializeRegion()"
ACPICA: Namespace: Add acpi_ns_handle_to_name()
ACPI / CPPC: set an error code on probe error path
ACPI / video: Add force_native quirk for HP Pavilion dv6
ACPI / video: Add force_native quirk for Dell XPS 17 L702X
ACPI / property: Hierarchical properties support update
ACPI / LPSS: enable hard LLP for DMA
ACPI / battery: If _BIX fails, retry with _BIF
ACPI / video: Move ACPI_VIDEO_NOTIFY_* defines to acpi/video.h
..
Add acpi_resource_consumer(). This takes a struct resource and searches
the ACPI namespace for a device whose current resource settings (_CRS)
includes the resource. It returns the device if it exists, or NULL if no
device uses the resource.
If more than one device uses the resource (this may happen in the case of
bridges), acpi_resource_consumer() returns the first one found by
acpi_get_devices() in its modified depth-first walk of the namespace.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On DT based systems, the of_dma_configure() API implements DMA
configuration for a given device. On ACPI systems an API equivalent to
of_dma_configure() is missing which implies that it is currently not
possible to set-up DMA operations for devices through the ACPI generic
kernel layer.
This patch fills the gap by introducing acpi_dma_configure/deconfigure()
calls that for now are just wrappers around arch_setup_dma_ops() and
arch_teardown_dma_ops() and also updates ACPI and PCI core code to use
the newly introduced acpi_dma_configure/acpi_dma_deconfigure functions.
Since acpi_dma_configure() is used to configure DMA operations, the
function initializes the dma/coherent_dma masks to sane default values
if the current masks are uninitialized (also to keep the default values
consistent with DT systems) to make sure the device has a complete
default DMA set-up.
The DMA range size passed to arch_setup_dma_ops() is sized according
to the device coherent_dma_mask (starting at address 0x0), mirroring the
DT probing path behaviour when a dma-ranges property is not provided
for the device being probed; this changes the current arch_setup_dma_ops()
call parameters in the ACPI probing case, but since arch_setup_dma_ops()
is a NOP on all architectures but ARM/ARM64 this patch does not change
the current kernel behaviour on them.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> [pci]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
On systems booting with a device tree, every struct device is associated
with a struct device_node, that provides its DT firmware representation.
The device node can be used in generic kernel contexts (eg IRQ
translation, IOMMU streamid mapping), to retrieve the properties
associated with the device and carry out kernel operations accordingly.
Owing to the 1:1 relationship between the device and its device_node,
the device_node can also be used as a look-up token for the device (eg
looking up a device through its device_node), to retrieve the device in
kernel paths where the device_node is available.
On systems booting with ACPI, the same abstraction provided by
the device_node is required to provide look-up functionality.
The struct acpi_device, that represents firmware objects in the
ACPI namespace already includes a struct fwnode_handle of
type FWNODE_ACPI as their member; the same abstraction is missing
though for devices that are instantiated out of static ACPI tables
entries (eg ARM SMMU devices).
Add a new fwnode_handle type to associate devices created out
of static ACPI table entries to the respective firmware components
and create a simple ACPI core layer interface to dynamically allocate
and free the corresponding firmware nodes so that kernel subsystems
can use it to instantiate the nodes and associate them with the
respective devices.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Tested-by: Hanjun Guo <hanjun.guo@linaro.org>
Tested-by: Tomasz Nowicki <tn@semihalf.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This function declared twice, so remove one declaration of it.
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have a couple of drivers, acpi_apd.c and acpi_lpss.c,
that need to pass extra build-in properties to the devices
they create. Previously the drivers added those properties
to the struct device which is member of the struct
acpi_device, but that does not work. Those properties need
to be assigned to the struct device of the platform device
instead in order for them to become available to the
drivers.
To fix this, this patch changes acpi_create_platform_device
function to take struct property_entry pointer as parameter.
Fixes: 20a875e2e8 (serial: 8250_dw: Add quirk for APM X-Gene SoC)
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Yazen Ghannam <yazen.ghannam@amd.com>
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ondrej reported that IRQs stopped working in v4.7 on several
platforms. A typical scenario, from Ondrej's VT82C694X/694X, is:
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: No IRQ available for PCI Interrupt Link [LNKA]
8139too 0000:00:0f.0: PCI INT A: no GSI
We're using PIC routing, so acpi_irq_balance == 0, and LNKA is already
active at IRQ 11. In that case, acpi_pci_link_allocate() only tries
to use the active IRQ (IRQ 11) which also happens to be the SCI.
We should penalize the SCI by PIRQ_PENALTY_PCI_USING, but
irq_get_trigger_type(11) returns something other than
IRQ_TYPE_LEVEL_LOW, so we penalize it by PIRQ_PENALTY_ISA_ALWAYS
instead, which makes acpi_pci_link_allocate() assume the IRQ isn't
available and give up.
Add acpi_penalize_sci_irq() so platforms can tell us the SCI IRQ,
trigger, and polarity directly and we don't have to depend on
irq_get_trigger_type().
Fixes: 103544d869 (ACPI,PCI,IRQ: reduce resource requirements)
Link: http://lkml.kernel.org/r/201609251512.05657.linux@rainbow-software.org
Reported-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Fix an unused function warning that started to appear after recent
changes in the ACPI EC driver (Eric Biggers).
- Fix the KERN_CONT usage in acpi_os_vprintf() that has become
(particularly) annoying recently (Joe Perches).
- Fix the fan status checking in the ACPI fan driver to avoid
returning incorrect error codes sometimes (Srinivas Pandruvada).
- Fix the ACPI Processor Aggregator driver (PAD) to always let the
special processor_aggregator driver from Xen take over when
running as Xen dom0 (Juergen Gross).
- Update the handling of reference device properties in ACPI by
allowing empty rows ("holes") to appear in reference property
lists (Mika Westerberg).
- Add a new MAINTAINERS entry for ACPI on ARM64 (Lorenzo Pieralisi).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=vpTd
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"This includes a couple of fixes needed after recent changes, two ACPI
driver fixes (fan and "Processor Aggregator"), an update of the ACPI
device properties handling code and a new MAINTAINERS entry for ACPI
on ARM64.
Specifics:
- Fix an unused function warning that started to appear after recent
changes in the ACPI EC driver (Eric Biggers).
- Fix the KERN_CONT usage in acpi_os_vprintf() that has become
(particularly) annoying recently (Joe Perches).
- Fix the fan status checking in the ACPI fan driver to avoid
returning incorrect error codes sometimes (Srinivas Pandruvada).
- Fix the ACPI Processor Aggregator driver (PAD) to always let the
special processor_aggregator driver from Xen take over when running
as Xen dom0 (Juergen Gross).
- Update the handling of reference device properties in ACPI by
allowing empty rows ("holes") to appear in reference property lists
(Mika Westerberg).
- Add a new MAINTAINERS entry for ACPI on ARM64 (Lorenzo Pieralisi)"
* tag 'acpi-extra-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
acpi_os_vprintf: Use printk_get_level() to avoid unnecessary KERN_CONT
ACPI / PAD: don't register acpi_pad driver if running as Xen dom0
ACPI / property: Allow holes in reference properties
MAINTAINERS: Add ARM64-specific ACPI maintainers entry
ACPI / EC: Fix unused function warning when CONFIG_PM_SLEEP=n
ACPI / fan: Fix error reading cur_state
DT allows holes or empty phandles for references. This is used for example
in SPI subsystem where some chip selects are native and others are regular
GPIOs. In ACPI _DSD we currently do not support this but instead the
preceding reference consumes all following integer arguments.
For example we would like to support something like the below ASL fragment
for SPI:
Package () {
"cs-gpios",
Package () {
^GPIO, 19, 0, 0, // GPIO CS0
0, // Native CS
^GPIO, 20, 0, 0, // GPIO CS1
}
}
The zero in the middle means "no entry" or NULL reference. To support this
we change acpi_data_get_property_reference() to take firmware node and
num_args as argument and rename it to __acpi_node_get_property_reference().
The function returns -ENOENT if the given index resolves to "no entry"
reference and -ENODATA when there are no more entries in the property.
We then add static inline wrapper acpi_node_get_property_reference() that
passes MAX_ACPI_REFERENCE_ARGS as num_args to support the existing
behaviour which some drivers have been relying on.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here is the big TTY and Serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by some
serial drivers, and they were all acked by the DMA maintainer. Also in
here is the long-suffering ACPI SPCR patchset, which was passed around
from maintainer to maintainer like a hot-potato. Seems I was the
sucker^Wlucky one. All of those patches have been acked by the various
subsystem maintainers as well.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNjEPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspwIcAn2uN
qCD8xQJ0Cs61hD1nUzhNygG8AJ94I4zz/fPGpyh/CtJfLQwtUdLhNA==
=Rken
-----END PGP SIGNATURE-----
Merge tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty and serial updates from Greg KH:
"Here is the big tty and serial patch set for 4.9-rc1.
It also includes some drivers/dma/ changes, as those were needed by
some serial drivers, and they were all acked by the DMA maintainer.
Also in here is the long-suffering ACPI SPCR patchset, which was
passed around from maintainer to maintainer like a hot-potato. Seems I
was the sucker^Wlucky one. All of those patches have been acked by the
various subsystem maintainers as well.
All of this has been in linux-next with no reported issues"
* tag 'tty-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (111 commits)
Revert "serial: pl011: add console matching function"
MAINTAINERS: update entry for atmel_serial driver
serial: pl011: add console matching function
ARM64: ACPI: enable ACPI_SPCR_TABLE
ACPI: parse SPCR and enable matching console
of/serial: move earlycon early_param handling to serial
Revert "drivers/tty: Explicitly pass current to show_stack"
tty: amba-pl011: Don't complain on -EPROBE_DEFER when no irq
nios2: dts: 10m50: Add tx-threshold parameter
serial: 8250: Set Altera 16550 TX FIFO Threshold
serial: 8250: of: Load TX FIFO Threshold from DT
Documentation: dt: serial: Add TX FIFO threshold parameter
drivers/tty: Explicitly pass current to show_stack
serial: imx: Fix DCD reading
serial: stm32: mark symbols static where possible
serial: xuartps: Add some register initialisation to cdns_early_console_setup()
serial: xuartps: Removed unwanted checks while reading the error conditions
serial: xuartps: Rewrite the interrupt handling logic
serial: stm32: use mapbase instead of membase for DMA
tty/serial: atmel: fix fractional baud rate computation
...
Pull x86 apic updates from Ingo Molnar:
"The main changes are:
- Persistent CPU/node numbering across CPU hotplug/unplug events.
This is a pretty involved series of changes that first fetches all
the information during bootup and then uses it for the various
hotplug/unplug methods. (Gu Zheng, Dou Liyang)
- IO-APIC hot-add/remove fixes and enhancements. (Rui Wang)
- ... various fixes, cleanups and enhancements"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86/apic: Fix silent & fatal merge conflict in __generic_processor_info()
acpi: Fix broken error check in map_processor()
acpi: Validate processor id when mapping the processor
acpi: Provide mechanism to validate processors in the ACPI tables
x86/acpi: Set persistent cpuid <-> nodeid mapping when booting
x86/acpi: Enable MADT APIs to return disabled apicids
x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping
x86/acpi: Enable acpi to register all possible cpus at boot time
x86/numa: Online memory-less nodes at boot time
x86/apic: Get rid of apic_version[] array
x86/apic: Order irq_enter/exit() calls correctly vs. ack_APIC_irq()
x86/ioapic: Ignore root bridges without a companion ACPI device
x86/apic: Update comment about disabling processor focus
x86/smpboot: Check APIC ID before setting up default routing
x86/ioapic: Fix IOAPIC failing to request resource
x86/ioapic: Fix lost IOAPIC resource after hot-removal and hotadd
x86/ioapic: Fix setup_res() failing to get resource
x86/ioapic: Support hot-removal of IOAPICs present during boot
x86/ioapic: Change prototype of acpi_ioapic_add()
x86/apic, ACPI: Fix incorrect assignment when handling apic/x2apic entries
...
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
'ARM Server Base Boot Requiremets' [1] mentions SPCR (Serial Port
Console Redirection Table) [2] as a mandatory ACPI table that
specifies the configuration of serial console.
Defer initialization of DT earlycon until ACPI/DT decision is made.
Parse the ACPI SPCR table, setup earlycon if required,
enable specified console.
Thanks to Peter Hurley for explaining how this should work.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.den0044a/index.html
[2] https://msdn.microsoft.com/en-us/library/windows/hardware/dn639132(v=vs.85).aspx
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Tested-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Tested-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bring in the upstream modifications so we can fixup the silent merge
conflict which is introduced by this merge.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Starting from Intel Skylake the iTCO watchdog timer registers were moved to
reside in the same register space with SMBus host controller. Not all
needed registers are available though and we need to unhide P2SB (Primary
to Sideband) device briefly to be able to read status of required NO_REBOOT
bit. The i2c-i801.c SMBus driver used to handle this and creation of the
iTCO watchdog platform device.
Windows, on the other hand, does not use the iTCO watchdog hardware
directly even if it is available. Instead it relies on ACPI Watchdog Action
Table (WDAT) table to describe the watchdog hardware to the OS. This table
contains necessary information about the the hardware and also set of
actions which are executed by a driver as needed.
This patch implements a new watchdog driver that takes advantage of the
ACPI WDAT table. We split the functionality into two parts: first part
enumerates the WDAT table and if found, populates resources and creates
platform device for the actual driver. The second part is the driver
itself.
The reason for the split is that this way we can make the driver itself to
be a module and loaded automatically if the WDAT table is found. Otherwise
the module is not loaded.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When the ACPI_DECLARE_PROBE_ENTRY macro was added in
commit e647b53227 ("ACPI: Add early device probing infrastructure"),
a stub macro adding an unused entry was added for the !CONFIG_ACPI
Kconfig option case to make sure kernel code making use of the
macro did not require to be guarded within CONFIG_ACPI in order to
be compiled.
The stub macro was never used since all kernel code that defines
ACPI_DECLARE_PROBE_ENTRY entries is currently guarded within
CONFIG_ACPI; it contains a typo that should be nonetheless fixed.
Fix the typo in the stub (ie !CONFIG_ACPI) ACPI_DECLARE_PROBE_ENTRY()
macro so that it can actually be used if needed.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fixes: e647b53227 (ACPI: Add early device probing infrastructure)
Cc: 4.4+ <stable@vger.kernel.org> # 4.4+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Following the fwnode of a device is currently a one-way road: We provide
ACPI_COMPANION() to obtain the fwnode but there's no (public) method to
do the reverse. Granted, there may be multiple physical_nodes, but often
the first one in the list is sufficient.
A handy function to obtain it was introduced with commit 3b95bd1605
("ACPI: introduce a function to find the first physical device"), but
currently it's only available internally.
We're about to add an EFI Device Path parser which needs this function.
Consider the following device path: ACPI(PNP0A03,0)/PCI(28,2)/PCI(0,0)
The PCI root is encoded as an ACPI device in the path, so the parser
has to find the corresponding ACPI device, then find its physical node,
find the PCI bridge in slot 1c (decimal 28), function 2 below it and
finally find the PCI device in slot 0, function 0.
To this end, make acpi_get_first_physical_node() public.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Majority of this update is about ASoC, including a few new drivers,
and the rest are mostly minor changes. The only substantial change in
ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and bug
fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002, Broadcom
Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960 and MAX98504,
Realtek RT5514 and Wolfson WM8758
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zx3K
-----END PGP SIGNATURE-----
Merge tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The majority of this update is about ASoC, including a few new
drivers, and the rest are mostly minor changes. The only substantial
change in ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and
bug fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002,
Broadcom Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960
and MAX98504, Realtek RT5514 and Wolfson WM8758"
* tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (278 commits)
sound: oss: Use kernel_read_file_from_path() for mod_firmware_load()
ASoC: Intel: Skylake: Delete an unnecessary check before the function call "release_firmware"
ASoC: Intel: Skylake: Fix NULL Pointer exception in dynamic_debug.
ASoC: samsung: Specify DMA channels through struct snd_dmaengine_pcm_config
ASoC: samsung: Fix error paths in the I2S driver's probe()
ASoC: cs53l30: Fix bit shift issue of TDM mode
ASoC: cs53l30: Fix a bug for TDM slot location validation
ASoC: rockchip: correct the spdif clk
ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members
ASoC: rsrc-card: use asoc_simple_card_parse_card_name()
ASoC: rsrc-card: use asoc_simple_dai instead of rsrc_card_dai
ASoC: rsrc-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card: use asoc_simple_card_parse_card_name()
ASoC: simple-card-utils: add asoc_simple_card_parse_card_name()
ASoC: simple-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card-utils: add asoc_simple_card_set_dailink_name()
ASoC: nau8825: drop redundant idiom when converting integer to boolean
ASoC: nau8825: jack connection decision with different insertion logic
ASoC: mediatek: Add HDMI dai-links to the mt8173-rt5650 machine driver
ASoC: mediatek: mt2701: fix non static symbol warning
...
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
* acpi-processor:
ACPI: enable ACPI_PROCESSOR_IDLE on ARM64
arm64: add support for ACPI Low Power Idle(LPI)
drivers: firmware: psci: initialise idle states using ACPI LPI
cpuidle: introduce CPU_PM_CPU_IDLE_ENTER macro for ARM{32, 64}
arm64: cpuidle: drop __init section marker to arm_cpuidle_init
ACPI / processor_idle: Add support for Low Power Idle(LPI) states
ACPI / processor_idle: introduce ACPI_PROCESSOR_CSTATE
* acpi-cppc:
mailbox: pcc: Add PCC request and free channel declarations
ACPI / CPPC: Prevent cpc_desc_ptr points to the invalid data
ACPI: CPPC: Return error if _CPC is invalid on a CPU
* acpi-apei:
ACPI / APEI: Add Boot Error Record Table (BERT) support
ACPI / einj: Make error paths more talkative
ACPI / einj: Convert EINJ_PFX to proper pr_fmt
* acpi-sleep:
ACPI: Execute _PTS before system reboot
* acpi-tables:
ACPI: Rename configfs.c to acpi_configfs.c to prevent link error
ACPI: add support for loading SSDTs via configfs
ACPI: add support for configfs
efi / ACPI: load SSTDs from EFI variables
spi / ACPI: add support for ACPI reconfigure notifications
i2c / ACPI: add support for ACPI reconfigure notifications
ACPI: add support for ACPI reconfiguration notifiers
ACPI / scan: fix enumeration (visited) flags for bus rescans
ACPI / documentation: add SSDT overlays documentation
ACPI: ARM64: support for ACPI_TABLE_UPGRADE
ACPI / tables: introduce ARCH_HAS_ACPI_TABLE_UPGRADE
ACPI / tables: move arch-specific symbol to asm/acpi.h
ACPI / tables: table upgrade: refactor function definitions
ACPI / tables: table upgrade: use cacheable map for tables
Conflicts:
arch/arm64/include/asm/acpi.h
ACPI 6.0 introduced an optional object _LPI that provides an alternate
method to describe Low Power Idle states. It defines the local power
states for each node in a hierarchical processor topology. The OSPM can
use _LPI object to select a local power state for each level of processor
hierarchy in the system. They used to produce a composite power state
request that is presented to the platform by the OSPM.
Since multiple processors affect the idle state for any non-leaf hierarchy
node, coordination of idle state requests between the processors is
required. ACPI supports two different coordination schemes: Platform
coordinated and OS initiated.
This patch adds initial support for Platform coordination scheme of LPI.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for ACPI reconfiguration notifiers to allow subsystems
to react to changes in the ACPI tables that happen after the initial
enumeration. This is similar with the way dynamic device tree
notifications work.
The reconfigure notifications supported for now are device add and
device remove.
Since ACPICA allows only one table notification handler, this patch
makes the table notifier function generic and moves it out of the
sysfs specific code.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the ACPI tables change as a result of a dinamically loaded table
and a bus rescan is required the enumeration/visited flag are not
consistent.
I2C/SPI are not directly enumerated in acpi_bus_attach(), however
the visited flag is set. This makes it impossible to check if an
ACPI device has already been enumerated by the I2C and SPI
subsystems. To fix this issue we only set the visited flags if
the device is not I2C or SPI.
With this change we also need to remove setting visited to false
from acpi_bus_attach(), otherwise if we rescan already enumerated
I2C/SPI devices we try to re-enumerate them.
Note that I2C/SPI devices can be enumerated either via a scan handler
(when using PRP0001) or via regular device_attach(). In either case
the flow goes through acpi_default_enumeration() which makes it the
ideal place to mark the ACPI device as enumerated.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For device nodes in both DT and ACPI, it possible to have named
child nodes which contain properties (an existing example being
gpio-leds). This adds a function to find a named child node for
a device which can be used by drivers for property retrieval.
For DT data node name matching, of_node_cmp() and similar functions
are made available outside of CONFIG_OF block so the new function
can reference these for DT and non-DT builds.
For ACPI data node name matching, a helper function is also added
which returns false if CONFIG_ACPI is not set, otherwise it
performs a string comparison on the data node name. This avoids
using the acpi_data_node struct for non CONFIG_ACPI builds,
which would otherwise cause a build failure.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add function needed for cpu to node mapping, and enable ACPI based
NUMA for ARM64 in Kconfig
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Robert Richter <rrichter@cavium.com>
[david.daney@cavium.com added ACPI_NUMA default to y for ARM64]
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Refer initrd_start, initrd_end directly from drivers/acpi/tables.c.
This allows to use the table upgrade feature in architectures
other than x86. Also this simplifies header files.
The patch renames acpi_table_initrd_init() to acpi_table_upgrade()
(what reflects the purpose of the function) and removes the unneeded
wraps early_acpi_table_init() and early_initrd_acpi_init().
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Acked-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_evaluate_dsm() will be used to handle the _DSM method in ACPI case.
It will be compiled in non-ACPI case, but the function is in acpi_bus.h
and acpi_bus.h can only be used in ACPI case, so this patch add the stub
function to linux/acpi.h to make compiled successfully in non-ACPI cases.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
acpi_dev_found() will be used to detect if a given ACPI device is in the
system. It will be compiled in non-ACPI case, but the function is in
acpi_bus.h and acpi_bus.h can only be used in ACPI case, so this patch add
the stub function to linux/acpi.h to make compiled successfully in
non-ACPI cases.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since acpi_numa_arch_fixup() is only used in arch ia64, move it there
to make a generic interface easier. This avoids empty function stubs
or some complex kconfig options for x86 and arm64.
Signed-off-by: Robert Richter <rrichter@cavium.com>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pci:
ACPI,PCI,IRQ: remove SCI penalize function
ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()
ACPI,PCI,IRQ: reduce static IRQ array size to 16
ACPI,PCI,IRQ: reduce resource requirements
* acpi-misc:
ACPI / sysfs: fix error code in get_status()
ACPI / device_sysfs: Clean up checkpatch errors
ACPI / device_sysfs: Change _SUN and _STA show functions error return to EIO
ACPI / device_sysfs: Add sysfs support for _HRV hardware revision
arm64: defconfig: Enable ACPI
ACPI / ARM64: Remove EXPERT dependency for ACPI on ARM64
ACPI / ARM64: Don't enable ACPI by default on ARM64
acer-wmi: Use acpi_dev_found()
eeepc-wmi: Use acpi_dev_found()
ACPI / utils: Rename acpi_dev_present()
* acpi-tools:
tools/power/acpi: close file only if it is open
Removing the SCI penalize function as the penalty is now calculated on the
fly.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
_OSI handling code grows giant and it's time to move them into one file.
This patch collects all _OSI handling code into one single file.
So that we only have the following functions to be used externally:
early_acpi_osi_init(): Used by DMI detections;
acpi_osi_init(): Used to initialize OSI command line settings and install
Linux specific _OSI handler;
acpi_osi_setup(): The API that should be used by the external quirks.
acpi_osi_is_win8(): The API is used by the external drivers to determine
if BIOS supports Win8.
CONFIG_DMI is not useful as stub dmi_check_system() can make everything
stub because of strip.
No functional changes.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch performs necessary cleanups before moving OSI support to
another file.
1. Change printk into pr_xxx
2. Do not initialize values to 0
3. Do not append additional "return" at the end of the function
4. Remove useless comments which may easily break line breaking rule
After fixing the coding style issues, rename functions to make them looking
like acpi_osi_xxx.
No functional changes.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes "int/unsigned int" to "bool" to simplify the code.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following commit always reports positive value when Apple hardware
queries _OSI("Darwin"):
Commit: 7bc5a2bad0
Subject: ACPI: Support _OSI("Darwin") correctly
However since this implementation places the judgement in runtime, it
breaks acpi_osi=!Darwin and cannot return unsupported for _OSI("WinXXX")
invoked before invoking _OSI("Darwin").
This patch fixes the issues by reverting the wrong support and implementing
the default behavior of _OSI("Darwin")/_OSI("WinXXX") on Apple hardware via
DMI matching.
Fixes: 7bc5a2bad0 (ACPI: Support _OSI("Darwin") correctly)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=92111
Reported-and-tested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves acpi_os_table_override() and
acpi_os_physical_table_override() to tables.c.
Along with the mechanisms, acpi_initrd_initialize_tables() is also moved to
tables.c to form a static function. The following functions are renamed
according to this change:
1. acpi_initrd_override() -> renamed to early_acpi_table_init(), which
invokes acpi_table_initrd_init()
2. acpi_os_physical_table_override() -> which invokes
acpi_table_initrd_override()
3. acpi_initialize_initrd_tables() -> renamed to acpi_table_initrd_scan()
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The problem is Linux registers pm_power_off = efi_power_off only if
we are in hardware reduced mode. Actually, what we also want is to do
this when ACPI S5 is simply not supported on non-legacy platforms.
Since some future Intel platforms are HW-full mode where the DSDT
fails to supply an _S5 object(without SLP_TYP), we should let such
kind of platform to leverage efi runtime service to poweroff.
This patch uses efi power off as first choice when S5 is unavailable,
even if there is a customized poweroff(driver provided, eg).
Meanwhile, the legacy platforms will not be affected because there is
no path for them to overwrite the pm_power_off to efi power off.
Suggested-by: Len Brown <len.brown@intel.com>
Reviewed-by: Matt Fleming <matt@codeblueprint.co.uk>
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
acpi_gsi_get_irq_type could be use out of GSI purpose.
Rename and make it available as a resource function.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch converts AML debugger into a loadable module.
Note that, it implements driver unloading at the level dependent on the
module reference count. Which means if ACPI debugger is being used by a
userspace program, "rmmod acpi_dbg" should result in failure.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In commit 60ba032ed7 ("ACPI / property: Drop size_prop from
acpi_dev_get_property_reference()"), the argument "const char *cells_name"
was dropped, but forgot to update the stub function in no-ACPI case,
it will lead to compile error when CONFIG_ACPI=n, easliy remove
"const char *cells_name" to fix it.
Fixes: 60ba032ed7 "ACPI / property: Drop size_prop from acpi_dev_get_property_reference()"
Reported-by: Kejian Yan <yankejian@huawei.com>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Support for the ACPI _CCA configuration object intended to tell
the OS whether or not a bus master device supports hardware
managed cache coherency and a new set of functions to allow
drivers to check the cache coherency support for devices in a
platform firmware interface agnostic way (Suravee Suthikulpanit,
Jeremy Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan,
Thomas Renninger).
- turbostat tool updates (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=XZiP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"The only new feature in this batch is support for the ACPI _CCA device
configuration object, which it a pre-requisite for future ACPI PCI
support on ARM64, but should not affect the other architectures.
The rest is fixes and cleanups, mostly in cpufreq (including
intel_pstate), the Operating Performace Points (OPP) framework and
tools (cpupower and turbostat).
Specifics:
- Support for the ACPI _CCA configuration object intended to tell the
OS whether or not a bus master device supports hardware managed
cache coherency and a new set of functions to allow drivers to
check the cache coherency support for devices in a platform
firmware interface agnostic way (Suravee Suthikulpanit, Jeremy
Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan, Thomas
Renninger).
- turbostat tool updates (Len Brown)"
* tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
PCI: ACPI: Add support for PCI device DMA coherency
PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()
of/pci: Fix pci_get_host_bridge_device leak
device property: ACPI: Remove unused DMA APIs
device property: ACPI: Make use of the new DMA Attribute APIs
device property: Adding DMA Attribute APIs for Generic Devices
ACPI: Adding DMA Attribute APIs for ACPI Device
device property: Introducing enum dev_dma_attr
ACPI: Honor ACPI _CCA attribute setting
cpufreq: CPPC: Delete an unnecessary check before the function call kfree()
PM / OPP: Add opp_rcu_lockdep_assert() to _find_device_opp()
PM / OPP: Hold dev_opp_list_lock for writers
PM / OPP: Protect updates to list_dev with mutex
PM / OPP: Propagate error properly from dev_pm_opp_set_sharing_cpus()
cpufreq: s5pv210-cpufreq: fix wrong do_div() usage
MAINTAINERS: update for intel P-state driver
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
...
Pull i2c updates from Wolfram Sang:
- New drivers: UniPhier (with and without FIFO)
- some drivers got some bigger rework: ismt, designware, img-scb (rcar
had to be reverted because issues were showing up just lately)
- ACPI: reworked the device scanning and added support for muxes
... and quite a lot of driver bugfixes and cleanups this time. All
files touched outside of the i2c realm have proper acks.
* 'i2c/for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (70 commits)
i2c: rcar: Revert the latest refactoring series
i2c: pnx: remove superfluous assignment
MAINTAINERS: i2c: drop i2c-pnx maintainer
MAINTAINERS: i2c: mark also subdirectories as maintained
i2c: cadence: enable driver for ARM64
i2c: i801: Document Intel DNV and Broxton
i2c: at91: manage unexpected RXRDY flag when starting a transfer
i2c: pnx: Use setup_timer instead of open coding it
i2c: add ACPI support for I2C mux ports
acpi: add acpi_preset_companion() stub
i2c: pxa: Add support for pxa910/988 & new configuration features
i2c: au1550: Convert to devm_kzalloc and devm_ioremap_resource
i2c-dev: Fix I2C_SLAVE ioctl comment
i2c-dev: Fix typo in ioctl name reference
i2c: sirf: tune the divider to make i2c bus freq more accurate
i2c: imx: Use -ENXIO as error in the NACK case
i2c: i801: Add support for Intel Broxton
i2c: i801: Add support for Intel DNV
i2c: mediatek: add i2c resume support
i2c: imx: implement bus recovery
...
Andy Shevchenko