Since the nlattr header is 4 bytes in size, it can cause the netlink
attribute payload to not be 8-byte aligned.
This is particularly troublesome for IFLA_STATS64 which contains 64-bit
statistic values.
Solve this by creating a dummy IFLA_PAD attribute which has a payload
which is zero bytes in size. When HAVE_EFFICIENT_UNALIGNED_ACCESS is
false, we insert an IFLA_PAD attribute into the netlink response when
necessary such that the IFLA_STATS64 payload will be properly aligned.
With help and suggestions from Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
The w5100-spi driver front-end only makes sense when the w5100
core driver is enabled, not for a configuration that only has w5300:
drivers/net/built-in.o: In function `w5100_spi_remove':
drivers/net/ethernet/wiznet/w5100-spi.c:277: undefined reference to `w5100_remove'
drivers/net/built-in.o: In function `w5100_spi_probe':
drivers/net/ethernet/wiznet/w5100-spi.c:272: undefined reference to `w5100_probe'
drivers/net/built-in.o: In function `w5200_spi_init':
drivers/net/ethernet/wiznet/w5100-spi.c:125: undefined reference to `w5100_ops_priv'
drivers/net/built-in.o: In function `w5200_spi_readbulk':
drivers/net/ethernet/wiznet/w5100-spi.c:125: undefined reference to `w5100_ops_priv'
drivers/net/built-in.o: In function `w5200_spi_writebulk':
drivers/net/ethernet/wiznet/w5100-spi.c:125: undefined reference to `w5100_ops_priv'
drivers/net/built-in.o:(.data+0x3ed1c): undefined reference to `w5100_pm_ops'
This adds an appropriate Kconfig dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 630cf09751 ("net: w5100: support SPI interface mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
Two new functions in bpf contain a cast from a 'u64' to a
pointer. This works on 64-bit architectures but causes a warning
on all 32-bit architectures:
kernel/trace/bpf_trace.c: In function 'bpf_perf_event_output_tp':
kernel/trace/bpf_trace.c:350:13: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
u64 ctx = *(long *)r1;
This changes the cast to first convert the u64 argument into a uintptr_t,
which is guaranteed to be the same size as a pointer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 9940d67c93 ("bpf: support bpf_get_stackid() and bpf_perf_event_output() in tracepoint programs")
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The results of of_mdiobus_register_{device|phy}() are never checked, so we
can make both these functions *void*...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver sets vlan_feature to netdev->features as hardware supports all of
them on vlan interface.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support VF drivers on Hyper-V. On Hyper-V, each VF instance presented to
the guest has an associated synthetic interface that shares the MAC address
with the VF instance. Typically these are bonded together to support
live migration. By default, the host delivers all the incoming packets
on the synthetic interface. Once the VF is up, we need to explicitly switch
the data path on the host to divert traffic onto the VF interface. Even after
switching the data path, broadcast and multicast packets are always delivered
on the synthetic interface and these will have to be injected back onto the
VF interface (if VF is up).
This patch implements the necessary support in netvsc to support Linux
VF drivers.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Philippe Reynes says:
====================
fec: ethtool: move to new api {get|set}_link_ksettings
Ethtool has a new api {get|set}_link_ksettings that deprecate
the old api {get|set}_settings. We update the fec driver to use
this new ethtool api.
For this first version, I've converted old u32 value in phy structure
to link_modes structure. Another way would be to replace u32 in
phy structure to use DECLARE_LINK_MODE_MASK for advertising, ....
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the fec driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The old ethtool api (get_setting and set_setting) has
generic phy functions phy_ethtool_sset and phy_ethtool_gset.
To supprt the new ethtool api (get_link_ksettings and
set_link_ksettings), we add generic phy function
phy_ethtool_ksettings_get and phy_ethtool_ksettings_set.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function convert_legacy_u32_to_link_mode and
convert_link_mode_to_legacy_u32 may be used outside
of ethtool.c. We rename them to ethtool_convert_...
and export them, so we could use them in others
drivers and modules.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tun_net_xmit() implementation don't need any external
lock since it relies on rcu protection for the tun data structure
and on socket queue lock for skb queuing.
This patch set the NETIF_F_LLTX feature bit in the tun device, so
that on xmit, in absence of qdisc, no serialization lock is acquired
by the caller.
The user space can remove the default tun qdisc with:
tc qdisc replace dev <tun device name> root noqueue
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We deleted a line of code and accidentally made the "return put_user()"
part of the if statement when it's supposed to be unconditional.
Fixes: 9f9a45beaa ('udp: do not expect udp headers on ioctl SIOCINQ')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch passes netlink attr data ptr directly to dev_get_stats
thus elimiating a stats copy.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vivien Didelot says:
====================
net: dsa: mv88e6xxx: factorize switch info
This patchset factorizes the mv88e6xxx code by sharing a new extendable
info structure to store static data such as switch family, product
number, number of ports, number of databases and the name.
The next step is to add a "flags" bitmap member to the info structure in
order to simplify the shared code with a feature-based logic instead of
checking their family/ID.
This is a step forward having a single mv88e6xxx driver supporting many
similar devices, like any usual Linux driver.
Changes v3 -> v4:
- constify probed name in DSA
- rebase patchset above conflicting commit 48ace4e
Changes v2 -> v3:
- update commit messages and add Andrew's tags
- keep the info lookup code in a separated function
- split the single switch ID reading in probe in a new commit
Changes v1 -> v2:
- define PORT_SWITCH_ID_PROD_NUM_* values
- use plain struct mv88e6xxx_info
- remove non used yet ps->rev
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ps->id is not needed anymore, so remove it as well as the related
defined values.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the number of databases to the info structure.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the ps->num_ports variable in favor of a new member of the info
structure. This removes the need to assign it at setup time.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an mv88e6xxx_family enum to the info structure for better family
indentification.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new switch info structure which is meant to store switch models
static information, such as product number, name, number of ports,
number of databases, etc.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read the switch ID only once, at probe time, to avoid multiple read
accesses and MII bus checking.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having a special case for the revision when probing
a switch model. The code gets cluttered with unnecessary defines, and
leads to errors when code such as mv88e6131_setup compares
PORT_SWITCH_ID_6131_B2 to ps->id which masks the revision.
Drop every revision definition, and lookup only the product number.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every driver assigns ps->ds even though it gets assigned in the shared
mv88e6xxx_setup_common function. Kill redundancy.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the dsa_switch_driver.probe function to return a const char *.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says
====================
nfp: cleanups and improvements
Main purpose of this set is to get rid of doing potentially long
mdelay()s but it also contains some trivial changes I've accumulated.
First two patches fix harmless copy-paste errors, next two clean up
the documentation and remove unused defines. Patch 5 clarifies the
interpretation of RX descriptor fields. Patch 6, by far the biggest,
adds ability to perform FW reconfig asynchronously thanks to which
we can stop using mdelay().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some callers of nfp_net_reconfig() are in atomic context so
we used to busy wait for commands to complete. In worst case
scenario that means locking up a core for up to 5 seconds
when a command times out. Lets add a timer-based mechanism
of asynchronously checking whether reconfiguration completed
successfully for atomic callers to use. Non-atomic callers
can now just sleep.
The approach taken is quite simple because (1) synchronous
reconfigurations always happen under RTNL (or before device
is registered); (2) we can coalesce pending reconfigs.
There is no need for request queues, timer which eventually
takes a look at reconfiguration result to report errors is
good enough.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Meaning of data_len and meta_len RX WB descriptor fields is
slightly confusing. Add a comment with a diagram clarifying
the layout. Also remove the buffer length validation:
(a) it's imprecise for static rx-offsets; (b) if firmware
is buggy enough to DMA past the end of the buffer
WARN_ON_ONCE() doesn't seem like a strong enough response.
skb_put() will do the checking for us anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFP_NET_RXR_MASK sounds like a mask which could be used on
NFP_NET_CFG_RXRS_ENABLE register but its value is quite
strange. In fact there are no users of this define so let's
just remove it. Same for TX rings.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Documentation in comments lacks CFG in some names.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason for those local variables to be static.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct checking error condition on wrong pointer -
copy/paste mistake most likely.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Sutter says:
====================
Minor IFF_NO_QUEUE conversion follow-up
The following series converts two further drivers away from setting
'tx_queue_len = 0' to adding IFF_NO_QUEUE to priv_flags instead.
The first one, rtl8188eu in staging didn't exist back when all drivers
were converted. The second one, openvswitch seems to have slipped through
my grep'ing back then, no idea why.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Taku Izumi says:
====================
FUJITSU Extended Socket driver version 1.1
This patchsets update FUJITSU Extended Socket network driver into version 1.1.
This mainly includes some improvements and minor bugfix.
v1->v2:
- Remove ioctl and debugfs facility according to David comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces spinlock of rx_status for
proper excusive control.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the fjes_change_mtu() method
by introducing new flag named FJES_RX_MTU_CHANGING_DONE
in rx_status. At the same time, default MTU value is
changed into 65510 bytes.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fjes_raise_intr_rxdata_task(), there's a bug of bitwise
check because of missing "& FJES_RX_POLL_WORK".
This patch fixes this bug.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are bugs of acounting statistics in fjes_xmit_frame().
Accounting self stats is wrong. accounting stats of other
EPs to be transmitted is right.
This patch fixes this bug.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch optimizes the following timeout value.
- FJES_DEVICE_RESET_TIMEOUT
- FJES_COMMAND_REQ_TIMEOUT
- FJES_COMMAND_REQ_BUFF_TIMEOUT
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the socfpga_dwmac_probe function, we have a call to socfpga_dwmac_setup,
which is already called from socfpga_dwmac_init later in the probe function.
Remove this extra call to socfpga_dwmac_setup.
Also we should not be calling socfpga_dwmac_setup() directly without wrapping
it around the proper reset assert/deasserts. That is because the
socfpga_dwmac_setup() is setting up PHY modes in the system manager, and it
is requires the EMAC's to be in reset during the PHY setup.
Reported-by: Matthew Gerlach <mgerlach@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These macros hide a ds variable and a return statement on error, which
can lead to locking issues. Kill them off.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I realized that when I added NETIF_F_TSO_MANGLEID as a TSO type I forgot to
add it to NETIF_F_ALL_TSO. This patch corrects that so the flag will be
included correctly.
The result should be minor as it was only used by a few drivers and in a
few specific cases such as when NETIF_F_SG was not supported on a device so
the TSO flags were cleared.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
Add support for offloads with IPv6 GRE tunnels
This patch series enables the use of segmentation and checksum offloads
with IPv6 based GRE tunnels.
In order to enable this series I had to make a change to
iptunnel_handle_offloads so that it would no longer free the skb. This was
necessary as there were multiple paths in the IPv6 GRE code that required
the skb to still be present so it could be freed. As it turned out I
believe this actually fixes a bug that was present in FOU/GUE based tunnels
anyway.
Below is a quick breakdown of the performance gains seen with a simple
netperf test passing traffic through a ip6gretap tunnel and then an i40e
interface:
Throughput Throughput Local Local Result
Units CPU Service Tag
Util Demand
%
3544.93 10^6bits/s 6.30 4.656 "before"
13081.75 10^6bits/s 3.75 0.752 "after"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code borrowed from bits and pieces of other protocols to
the IPv6 GRE path so that we can support GSO over IPv6 based GRE tunnels.
By adding this support we are able to significantly improve the throughput
for GRE tunnels as we are able to make use of GSO.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since GRE doesn't really care about L3 protocol we can support IPv4 and
IPv6 using the same offloads. With that being the case we can add a call
to register the offloads for IPv6 as a part of our GRE offload
initialization.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the basic offloads we support on most devices.
Specifically with this patch set we can support checksum offload, basic
scatter-gather, and highdma.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we were creating an ip6gretap interface the MTU was about 6 bytes
short of what was needed. It turns out we were not taking the Ethernet
header into account and as a result we were eating into the 8 bytes
reserved for the encap limit.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the IP tunnel core function iptunnel_handle_offloads so
that we return an int and do not free the skb inside the function. This
actually allows us to clean up several paths in several tunnels so that we
can free the skb at one point in the path without having to have a
secondary path if we are supporting tunnel offloads.
In addition it should resolve some double-free issues I have found in the
tunnels paths as I believe it is possible for us to end up triggering such
an event in the case of fou or gue.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Akinobu Mita says:
====================
net: w5100: add support W5100/W5200 for SPI interface
This series add support for Wiznet W5100 and W5200 for SPI interface.
We can easily find the ethernet modules and shield for Arduino with
these chips for purchase. I've tested them with BeagleBone.
Wiznet W5100 for mmio access has already supported by w5100 driver.
In order to share the code between mmio mode and SPI mode, this series
firstly adds ability to support another register access interface to
the existing w5100 driver. This ground work also requires to introduce
workqueue and threaded irq because SPI transfers are callable only from
contexts that can sleep unlike mmio access.
The latter part of this series adds w5100-spi driver which actually
support W5100 and W5200 for SPI interface. Supporting W5100 is
straight forward because it only required to add a register access
interface by the SPI transfer. W5100 and W5200 have similar memory
map which justifies adding W5200 support to w5100 driver.
* Changes from v2 to v3
- Add comment for reg_lock
- Add ability to allocate ops specific data structure
- Allocate w5200 ops specific data structure to put DMA-safe buffer
- Add missing chip_id assignment for w5100_*_ops
* Changes from v1 to v2
- Use a plain single pointer instead of SKB queue, spotted by David S. Miller
- Correct timeout period in w5100_command
- Use spi_write_then_read instead of spi_write which needs DMA-safe buffer
- Support W5200
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller