Following the introduction of the compatible-data field,
it's now possible to further abstract the clock initialization.
This will allow to support SoC with a different clock setup.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds an orion_watchdog_data structure to hold compatible-data
information. This allows to remove the driver-wide definition and to
be able to add support for multiple compatible-strings in the future.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to prepare to support multiple compatible-strings, this
commit adds a device structure to hold the driver's state.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
After adding the IRQ request, the BRIDGE_CAUSE bit should be cleared by the
bridge interrupt controller. There's no longer a need to do it in the watchdog
driver, so we can simply remove it.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to support other SoC, it's required to distinguish
the 'control' timer register, from the 'rstout' register
that enables system reset on watchdog expiration.
To prevent a compatibility break, this commit adds a fallback
to a hardcoded RSTOUT address.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
DT-enabled plaforms, where the irqchip driver for the brigde interrupt
controller is available, can handle the watchdog IRQ properly. Therefore,
request the interrupt and add a dummy handler that merely calls panic().
This is done in order to have an initial 'ack' of the interruption,
which clears the watchdog state.
Furthermore, since some platforms don't have such IRQ, this commit
makes the interrupt specification optional.
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Having the watchdog initially fully stopped is important to avoid
any spurious watchdog triggers, in case the registers are not in
its reset state.
If the watchdog rstout is enabled and the watchdog counter running,
this initial stop is not performed, to comply with the 'nowayout'
parameter.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
These are not used anywhere so it's safe to remove them.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since the timer control register is shared with the clocksource driver,
use the recently introduced atomic_io_clear_set() to access such register.
Given the watchdog core already provides serialization for all the
watchdog ops, this commit allows to remove the spinlock entirely.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds a check for clk_prepare_enable success and introduces
an error path to disable the clock properly.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Most WDT driver modules return ENODEV during modprobe if
no valid device was found, but w83697hf_wdt returns EIO.
Let w83697hf_wdt return ENODEV.
Signed-off-by: Stanislav Kholmanskikh <stanislav.kholmanskikh@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On archs like S390 or um this driver cannot build nor work.
Make it depend on HAS_IOMEM to bypass build failures.
drivers/built-in.o: In function `dw_wdt_drv_probe':
drivers/watchdog/dw_wdt.c:302: undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
If the watchdog has already triggered for whatever reason, it won't restart
unless the trigger is reset.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Major difference is that the watchdog control and counter registers
are different on both chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Instead of requiring the user to provide an IO address per module
parameter, auto-detect it as well as supported chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Try to reset the watchdog counter 4 or 2 times more often than actually
requested, to avoid spurious watchdog reset.
If this is not possible because of the min_heartbeat value, reset it at
the min_heartbeat period.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the min_heartbeat value instead of the calculated heartbeat value for
the first watchdog reset to avoid spurious watchdog reset.
Resetting the watchdog counter during init might lead to a watchdog fault
reset because the watchdog counter has to be running for at least
min_heartbeat.
Resetting the watchdog counter after heartbeat might lead to a watchdog
timeout reset because the watchdog counter is running for more than
max_heartbeat time.
Using min_heartbeat instead of heartbeat does not guarantee that the
watchdog won't trigger a reset, but at least it reduces the chances to be
in such a case.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Fix the secs_to_ticks macro in case 0 is passed as an argument.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The at91sam9 watchdog timer can only be configured once, and the current
implementation tries to configure it in a static way:
- 2 seconds timeout
- wdt restart every 500ms
If the timer has already been configured with different values, it returns an
error and do not create any watchdog device.
This is not critical if the watchdog is disabled, but if it has been enabled with
different timeout values it will lead to a SoC reset.
This patch series tries to address this issue by adapting the heartbeat value
according the WDT timer config:
- it first tries to configure the timer as requested.
- if it fails it fallbacks to the current config, adapting its heartbeat timer
to the needs
This patch series also move to a dynamically allocated at91wdt device instead
of the static instance.
It adds a new at91 wdt type: software. This new type make use of the at91 wdt
interrupt to trigger a software reboot.
Finally it adds several properties to the device tree bindings.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
mach-moxart lacks a separate register for reset; as a workaround,
add a function that can be hooked to arm_pm_restart.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Convert mpc8xxx_wdt.c to the new watchdog API.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
'sirfsoc_wdt_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is being submitted to output a general string when the panic comes
in that informs the user of the possible places to look for the source of the
NMI. Because various systems log the message in different places this would
give a single display of where to go look instead of code that acts on all
these different server names or IDs.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is nothing ARM specific in this driver, and we intend to use it on the
Xtensa architecture. Also, clk.h now includes stubs for !CONFIG_HAVE_CLK, so
the driver should build anyway.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We should set watchdog timer to be disabled in low power mode,
as there is no service running in background, otherwise, system
will reset unexpected.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
A good watchdog driver is supposed to report when it was responsible
for resetting the system. Implement this for the s3c2410, at least on
exynos5250 and exynos5420 where we already have a pointer to the PMU
registers to read the information.
Note that exynos4 SoCs also provide the reset status, but providing
that is left as an exercise for future changes and is not plumbed up
in this patch series. Also note the exynos4 SoCs don't appear to need
any PMU config, which is why this patch separates the concepts of
having PMU Registers vs. needing PMU Config.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add device tree support for exynos5250 and 5420 SoCs and use syscon regmap interface
to configure AUTOMATIC_WDT_RESET_DISABLE and MASK_WDT_RESET_REQUEST registers of PMU
to mask/unmask enable/disable of watchdog in probe and s2r scenarios.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The existing watchdog timeout worked OK but didn't deal with
rounding in an ideal way when dividing out all of its clocks.
Specifically if you had a timeout of 32 seconds and an input clock of
66666666, you'd end up setting a timeout of 31.9998 seconds and
reporting a timeout of 31 seconds.
Specifically DBG printouts showed:
s3c2410wdt_set_heartbeat: count=16666656, timeout=32, freq=520833
s3c2410wdt_set_heartbeat: timeout=32, divisor=255, count=16666656 (0000ff4f)
and the final timeout reported to the user was:
((count / divisor) * divisor) / freq
(0xff4f * 255) / 520833 = 31 (truncated from 31.9998)
the technically "correct" value is:
(0xff4f * 255) / (66666666.0 / 128) = 31.9998
By using "DIV_ROUND_UP" we can be a little more correct.
s3c2410wdt_set_heartbeat: count=16666688, timeout=32, freq=520834
s3c2410wdt_set_heartbeat: timeout=32, divisor=255, count=16666688 (0000ff50)
and the final timeout reported to the user:
(0xff50 * 255) / 520834 = 32
the technically "correct" value is:
(0xff50 * 255) / (66666666.0 / 128) = 32.0003
We'll use a DIV_ROUND_UP to solve this, generally erroring on the side
of reporting shorter values to the user and setting the watchdog to
slightly longer than requested:
* Round input frequency up to assume watchdog is counting faster.
* Round divisions by divisor up to give us extra time.
At the same time we can avoid a for loop by just doing the right math.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On modern SoCs the watchdog timer is parented on a clock that doesn't
change every time we have a cpufreq change. That means we don't need
to constantly adjust the watchdog timer, so avoid registering for and
dealing with cpufreq transitions unless we've actually got
CONFIG_ARM_S3C24XX_CPUFREQ defined.
Note that this is more than just an optimization. The s3c2410
watchdog driver actually pats the watchdog on every CPU frequency
change. On modern systems these happen many times per second (even in
a system where "nothing" is happening). That effectively makes any
userspace watchdog program useless (the watchdog is constantly patted
by the kernel). If we need ARM_S3C24XX_CPUFREQ defined on a
multiplatform kernel we'll need to make sure that kernel supports
common clock and change this to user common clock framework.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds a watchdog driver for devices controlled through GPIO,
(Analog Devices ADM706, Maxim MAX823, National NE555 etc).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The keystone arch uses the same IP watchdog, so add "ti,keystone-wdt"
compatible and correct identity.
The Keystone arch is using clocks in DT and source clock for watchdog
has to be specified, so add this to binding.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Currently, the davinci watchdog can be read while counting,
so we can add ability to report the remaining time before
the system will reboot.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Some SoCs, like Keystone 2, can support more than one WDT and each
watchdog device has to use it's own base address, clock source,
watchdog device, so add new davinci_wdt_device structure to hold
device data.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
To reduce code duplicate and increase code readability use WDT core
code to handle WDT interface.
Remove io_lock as the WDT core uses mutex to lock each wdt device.
Remove wdt_state as the WDT core tracks state with its own variable.
The watchdog_init_timeout() can read timeout value from timeout-sec
property if the passed value is out of bounds. The heartbeat is
initialized in next way. If heartbeat is not set thought module
parameter, try to read it's value from WDT node timeout-sec property.
If node has no one, use default value.
The heartbeat is hold in wdd->timeout by WDT core, so use it in
order to set timeout period.
Davinci WDT can't be stopped and once it's expired - it can be
rearmed only after hardware reset, that's why nowayout feature
is enforced.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This change introduces debugfs support for the BCM281xx watchdog driver.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This commit adds support for the watchdog timer used on the BCM281xx
family of SoCs.
Signed-off-by: Markus Mayer <markus.mayer@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is valid for a watchdog driver to have 0 for a "min" and "max"
timeout if the driver doesn't need the core to enforce the concepts of
min and max. The s3c2410_wdt driver is one such driver. Specifically
it can be hard for that driver to come up with a static "max" on all
platforms without a lot more information since the input clock on
S3C2410 and S3C2440 can change with DVFS.
As written, watchdog_init_timeout() will not ever read "timeout-sec"
on these drivers since watchdog_timeout_invalid() will _never_ return
true. Change to not consider a timeout_parm of 0 as valid even if
min/max aren't specified by the driver. Also handle the case when
there is no min/max and no "timeout-sec" property.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Updates of SoC-near drivers and other driver updates that makes more sense to
take through our tree.
The largest part of this is a conversion of device registration for some
renesas shmobile/sh devices over to use resources. This has required
coordination with the corresponding arch/sh changes, and we've agreed
to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure firmware,
which is what is used on many of the commercial Nvidia Tegra products
that are in the market, including the Nvidia Shield. The code is local
to arch/arm at this time since it's uncertain whether it will be shared
with arm64 longer-term, if needed we will refactor later.
A couple of new RTC drivers used on ARM boards, merged through our tree
on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=JJlw
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM driver updates from Olof Johansson:
"Updates of SoC-near drivers and other driver updates that makes more
sense to take through our tree.
The largest part of this is a conversion of device registration for
some renesas shmobile/sh devices over to use resources. This has
required coordination with the corresponding arch/sh changes, and
we've agreed to merge the arch/sh changes through our tree.
Added in this branch is support for Trusted Foundations secure
firmware, which is what is used on many of the commercial Nvidia Tegra
products that are in the market, including the Nvidia Shield. The
code is local to arch/arm at this time since it's uncertain whether it
will be shared with arm64 longer-term, if needed we will refactor
later.
A couple of new RTC drivers used on ARM boards, merged through our
tree on request by the RTC maintainer.
... plus a bunch of smaller updates across the board, gpio conversions
for davinci, etc"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
watchdog: davinci: rename platform driver to davinci-wdt
tty: serial: Limit msm_serial_hs driver to platforms that use it
mmc: msm_sdcc: Limit driver to platforms that use it
usb: phy: msm: Move mach dependent code to platform data
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
...
platform device name from generic "watchdog"
to something more specific.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=C9qR
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/watchdog' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
This patch updates the davinci watchdog
platform device name from generic "watchdog"
to something more specific.
* tag 'davinci-for-v3.14/watchdog' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
watchdog: davinci: rename platform driver to davinci-wdt
Signed-off-by: Kevin Hilman <khilman@linaro.org>
As we switch to use the watchdog core which permits more than one
active watchdog in the system, rename platform driver to
"davinci-wdt" to be identifiable.
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
CONFIG_USB_DEBUG is going away, and all of the other USB drivers no
longer rely on "debug" module parameters for debugging lines, so move
the pcwd_usb driver to use the dynamic debug infrastructure to be more
in line with the rest of the kernel.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
If loaded with isapnp = 0 the driver explodes. This is catching
people out now and then. What should happen in the working case is
a complete mystery and the code appears terminally confused, but we
can at least make the error path work properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Partially-Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=53991
After commit 487722cf2 (watchdog: Get rid of MODULE_ALIAS_MISCDEV
statements) the affected drivers no longer need to include miscdevice.h.
Only exception is rt2880_wdt.c which never needed it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use helper functions named similar to other drivers to access
superio registers.
Request memory region only when needed, and use request_muxed_region().
This lets other devices (hwmon, gpio) use the same region.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There is no need to enable the watchdog device if it is already enabled.
Also, when enabling the watchdog device, only set the watchdog device
enable bit and do not touch other bits; depending on the chip type,
those bits may enable other functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It is unnecessary to enable the logical device and WDT0 each time
the watchdog is accessed. Do it only once during initialization.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
All OMAP IP blocks expect LE data, but CPU may operate in BE mode.
Need to use endian neutral functions to read/write h/w registers.
I.e instead of __raw_read[lw] and __raw_write[lw] functions code
need to use read[lw]_relaxed and write[lw]_relaxed functions.
If the first simply reads/writes register, the second will byteswap
it if host operates in BE mode.
Changes are trivial sed like replacement of __raw_xxx functions
with xxx_relaxed variant.
Signed-off-by: Victor Kamensky <victor.kamensky@linaro.org>
Signed-off-by: Taras Kondratiuk <taras.kondratiuk@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
As CSR SiRF is converted to multi platform CLOCK_TICK_RATE is a dummy
value that seems to match the right value is used.
(arch/arm/mach-prima2/include/mach/timex.h which defined CLOCK_TICK_RATE
to 1000000 was removed in commit cf82e0e (ARM: sirf: enable
multiplatform support); marco used the same file.)
To not depend on that dummy value use a local #define instead.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
We changed "buf" from being an array of 6 chars to being a pointer this
sizeof(buf) needs to be updated as well.
Fixes: 2ddb8089a7e5 ('watchdog: pcwd_usb: Use allocated buffer for usb_control_msg')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
In case of error, the function devm_request_and_ioremap() returns NULL
pointer not ERR_PTR(). Fix it by using devm_ioremap_resource() instead
of devm_request_and_ioremap().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
I just can't find any value in MODULE_ALIAS_MISCDEV(WATCHDOG_MINOR)
and MODULE_ALIAS_MISCDEV(TEMP_MINOR) statements.
Either the device is enumerated and the driver already has a module
alias (e.g. PCI, USB etc.) that will get the right driver loaded
automatically.
Or the device is not enumerated and loading its driver will lead to
more or less intrusive hardware poking. Such hardware poking should be
limited to a bare minimum, so the user should really decide which
drivers should be tried and in what order. Trying them all in
arbitrary order can't do any good.
On top of that, loading that many drivers at once bloats the kernel
log. Also many drivers will stay loaded afterward, bloating the output
of "lsmod" and wasting memory. Some modules (cs5535_mfgpt which gets
loaded as a dependency) can't even be unloaded!
If defining char-major-10-130 is needed then it should happen in
user-space.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Jim Cromie <jim.cromie@gmail.com>
timeout_to_regval() returns a valid error code. Might as well use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
usb_control_msg() must use a dma-capable buffer.
This fixes the following error reported by smatch:
drivers/watchdog/pcwd_usb.c:257 usb_pcwd_send_command() error: doing dma on the
stack (buf)
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d06310)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
On CSR SiRFprimaII and SiRFatlasVI, the 6th timer can act as a watchdog
timer when the Watchdog mode is enabled.
watchdog occur when TIMER watchdog counter matches the value software
pre-set, when this event occurs, the effect is the same as the system
software reset.
Signed-off-by: Xianglong Du <Xianglong.Du@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Cc: Romain Izard <romain.izard.pro@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
of_match_ptr() is a macro used to avoid undefined reference error if
CONFIG_OF is used to selectively compile in or out the
data structure. It is defined as follows:
#ifdef CONFIG_OF
#define of_match_ptr(ptr) ptr
#else
#define of_match_ptr(ptr) NULL
#endif
In the case of this series, none of the drivers use CONFIG_OF macro to
compile out the data structure (i.e., the data structure is always
defined).
Hence the use of of_match_ptr() does not make any sense. Thus removing
it to make the code look simpler for readability.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
There seems to be some confusion here which functions return positive
numbers and which return negative error codes.
copy_to_user() returns the number of bytes remaining to be copied but we
want to return -EFAULT.
The rest is just clean up. get_user() actually returns zero on success
and -EFAULT on error so we can preserve the error code. The
timeout_to_regval() function returns -EINVAL on failure, but we can
propogate that back instead of hardcoding -EINVAL ourselves.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
--
This patch adds a watchdog driver for the main hardware watchdog timer
found on MOXA ART SoCs.
The MOXA ART SoC provides one writable timer register, restarting
the hardware once it reaches zero. The register is auto decremented
every APB clock cycle.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Added __user annotation to fix the following sparse warnings.
Also, it makes 'kempld_prescaler' static because it is used
only in this file.
drivers/watchdog/kempld_wdt.c:70:11: warning: symbol 'kempld_prescaler' was not declared. Should it be static?
drivers/watchdog/kempld_wdt.c:364:23: warning: incorrect type in initializer (different address spaces)
drivers/watchdog/kempld_wdt.c:364:23: expected int const [noderef] <asn:1>*register __p
drivers/watchdog/kempld_wdt.c:364:23: got int *<noident>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Enable auto loading by udev when imx2_wdt is compiled as a module.
Signed-off-by: Niels de Vos <ndevos@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This is necessary to make the driver work with platforms using the
common clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The dw_wdt only provides PM_SLEEP operations, so convert the driver
to use SIMPLE_DEV_PM_OPS instead of populating the struct manually.
This has the added effect of simplifying the CONFIG_PM ifdefs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
not compiled for ages, and recent versions of gcc for it are broken.
Remove support for it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=V6n6
-----END PGP SIGNATURE-----
Merge tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull h8300 platform removal from Guenter Roeck:
"The patch series has been in -next for more than one relase cycle. I
did get a number of Acks, and no objections.
H8/300 has been dead for several years, the kernel for it has not
compiled for ages, and recent versions of gcc for it are broken.
Remove support for it"
* tag 'h8300-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
CREDITS: Add Yoshinori Sato for h8300
fs/minix: Drop dependency on H8300
Drop remaining references to H8/300 architecture
Drop MAINTAINERS entry for H8/300
watchdog: Drop references to H8300 architecture
net/ethernet: Drop H8/300 Ethernet driver
net/ethernet: smsc9194: Drop conditional code for H8/300
ide: Drop H8/300 driver
Drop support for Renesas H8/300 (h8300) architecture
Commit b5b4bb3f6a (of: only include prom.h on sparc) removed implicit
includes of of_*.h headers by powerpc's prom.h. Some components were
missed in initial clean-up patch, so add the necessary includes to fix
powerpc builds.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-ide@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
mrst is used as common name to represent all intel_mid type
soc's. But moorsetwon is just one of the intel_mid soc. So
renamed them to use intel_mid.
This patch mainly renames the variables and related
functions that uses *mrst* prefix with *intel_mid*.
To ensure that there are no functional changes, I have compared
the objdump of related files before and after rename and found
the only difference is symbol and name changes.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-6-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Following files contains code that is common to all intel mid
soc's. So renamed them as below.
mrst/mrst.c -> intel-mid/intel-mid.c
mrst/vrtc.c -> intel-mid/intel_mid_vrtc.c
mrst/early_printk_mrst.c -> intel-mid/intel_mid_vrtc.c
pci/mrst.c -> pci/intel_mid_pci.c
Also, renamed the corresponding header files and made changes
to the driver files that included these header files.
To ensure that there are no functional changes, I have compared
the objdump of renamed files before and after rename and found
that the only difference is file name change.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Link: http://lkml.kernel.org/r/1382049336-21316-4-git-send-email-david.a.cohen@linux.intel.com
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This driver has a section mismatch, for probe and remove functions,
leading to the following warning during the compilation.
WARNING: drivers/watchdog/built-in.o(.data+0x24): Section mismatch in
reference from the variable sunxi_wdt_driver to the function
.init.text:sunxi_wdt_probe()
The variable sunxi_wdt_driver references
the function __init sunxi_wdt_probe()
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
STAGE_CFG bits are defined as [5:4] bits. However, '(((x) & 0x30) << 4)'
handles [9:8] bits. Thus, it should be fixed in order to handle
[5:4] bits.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Calling the WDIOC_GETSTATUS & WDIOC_GETBOOTSTATUS and twice will cause a
interruptible deadlock.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch is to prevent hpwdt from loading on any auxilary iLO devices defined
after the initial (or main) iLO device. All auxilary iLO devices will have a
subsystem device ID set to 0x1979 in order for hpwdt to differentiate between
the two types.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Lisa Mitchell <lisa.mitchell@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Pull watchdog updates from Wim Van Sebroeck:
- New watchdog driver for Allwinner A10/A13
- some devm_ioremap_resource simplifications
- a s3c2410_wdt change that removes the global variables
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: s3c2410_wdt: simplify use of devm_ioremap_resource
watchdog: simplify platform_get_resource_byname/devm_ioremap_resource
watchdog: ts72xx_wdt: simplify use of devm_ioremap_resource
watchdog: nuc900_wdt.c: simplify use of devm_ioremap_resource
watchdog: sunxi: New watchdog driver for Allwinner A10/A13
watchdog: s3c2410_wdt: remove the global variables
We cannot assume that the inline assembler code always ends up in the same
file as the original C file. So make any assembler labels that are called
with "extern" by C global
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the driver for the watchdog found in the Allwinner A10 and
A13 SoCs. It has DT-support and uses the new watchdog framework.
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch removes the global variables in the driver file and
group them into a structure.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
This patch is being created to use the UEFI bits in the type 219 SMBIOS
record in order to decide whether or not to execute BIOS code. This is a
better solution than to depend on the iCRU bit since not all future servers
will use iCRU.
Signed-off-by: Thomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
----
drivers/watchdog/hpwdt.c | 9 ++++++---
1 files changed, 6 insertions(+), 3 deletions(-)
In watchdog_ping(), 'start' is called automatically when 'ping' function call
is not configured.
Softdog driver has same handling in both cases - start and ping, so 'ping' OPS
can be removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This patch adds the driver for the watchdog devices found on MEN Mikro
Elektronik A21 VMEbus CPU Carrier Boards. It has DT-support and uses the
watchdog framework.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The bits in BRIDGE_CAUSE are documented as RW0C - read, write 0 to
clear. If we read the register, mask off the watchdog bit, and
write it back, we're actually clearing every interrupt which wasn't
pending at the time we read the register - and that is racy.
Fix this to only write ~WATCHDOG_BIT to the register, which means
we write as zero only the watchdog bit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog infrastructure in Dove is no different from that in
Orion5x or Kirkwood, so let's enable it for Dove. The only things
missing are a few register settings in Dove's bridge-regs.h.
Rather than duplicating the same register bit masks for the RSTOUTn_MASK
and BRIDGE_CAUSE registers, move the definitions into the watchdog
driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This adds a driver for watchdog timer hardware present on Broadcom BCM2835 SoC,
used in Raspberry Pi and Roku 2 devices.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-watchdog@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org
Interrupt request doesn't use the right API: The TWD watchdog uses a per-cpu
interrupt (usually interrupt #30), and the GIC configuration should flag it as
such. With this setup, request_irq() should fail, and the right API is
request_percpu_irq(), together with enable_percpu_irq()/disable_percpu_irq().
Nothing ensures the userspace ioctl() will end-up kicking the watchdog on the
right CPU.
There are no users of this driver since a long time and it makes more sense to
get rid of it as nobody is looking to fix it.
In case somebody wakes up after this has been removed and needs it, please
revert this driver and pick these updates (These were never pushed to mainline):
http://comments.gmane.org/gmane.linux.ports.arm.kernel/245998
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Watchdog 1.01.a is also compatible with 1.00.a.
Add the origin version to compatible list.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Ezequiel Garcia