The RFC 4884 spec is largely the same between IPv4 and IPv6.
Factor out the IPv4 specific parts in preparation for IPv6 support:
- icmp types supported
- icmp header size, and thus offset to original datagram start
- datagram length field offset in icmp(6)hdr.
- datagram length field word size: 4B for IPv4, 8B for IPv6.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Only accept packets with original datagram len field >= header len.
The extension header must start after the original datagram headers.
The embedded datagram len field is compared against the 128B minimum
stipulated by RFC 4884. It is unlikely that headers extend beyond
this. But as we know the exact header length, check explicitly.
2) Remove the check that datagram length must be <= 576B.
This is a send constraint. There is no value in testing this on rx.
Within private networks it may be known safe to send larger packets.
Process these packets.
This test was also too lax. It compared original datagram length
rather than entire icmp packet length. The stand-alone fix would be:
- if (hlen + skb->len > 576)
+ if (-skb_network_offset(skb) + skb->len > 576)
Fixes: eba75c587e ("icmp: support rfc 4884")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable status is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed. Also put the variable declarations into
reverse christmas tree order.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a deadlock, this patch fixes it by making
sure the work is canceled without holding the global ovs lock. This is
done by moving the reorder processing one layer up to the netns level.
Fixes: eac87c413b ("net: openvswitch: reorder masks array based on usage")
Reported-by: syzbot+2c4ff3614695f75ce26c@syzkaller.appspotmail.com
Reported-by: syzbot+bad6507e5db05017b008@syzkaller.appspotmail.com
Reviewed-by: Paolo <pabeni@redhat.com>
Signed-off-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sockopt accepts two kinds of parameters, using struct
sctp_sack_info and struct sctp_assoc_value. The mentioned commit didn't
notice an implicit cast from the smaller (latter) struct to the bigger
one (former) when copying the data from the user space, which now leads
to an attempt to write beyond the buffer (because it assumes the storing
buffer is bigger than the parameter itself).
Fix it by allocating a sctp_sack_info on stack and filling it out based
on the small struct for the compat case.
Changelog stole from an earlier patch from Marcelo Ricardo Leitner.
Fixes: ebb25defdc ("sctp: pass a kernel pointer to sctp_setsockopt_delayed_ack")
Reported-by: syzbot+0e4699d000d8b874d8dc@syzkaller.appspotmail.com
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2020-07-23
This series contains updates to ice driver only.
Jake refactors ice_discover_caps() to reduce the number of AdminQ calls
made. Splits ice_parse_caps() to separate functions to update function
and device capabilities separately to allow for updating outside of
initialization.
Akeem adds power management support.
Paul G refactors FC and FEC code to aid in restoring of PHY settings
on media insertion. Implements lenient mode and link override support.
Adds link debug info and formats existing debug info to be more
readable. Adds support to check and report additional autoneg
capabilities. Implements the capability to detect media cage in order to
differentiate AUI types as Direct Attach or backplane.
Bruce implements Total Port Shutdown for devices that support it.
Lev renames low_power_ctrl field to lower_power_ctrl_an to be more
descriptive of the field.
Doug reports AOC types as media type fiber.
Paul S adds code to handle 1G SGMII PHY type.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Christoph Hellwig says:
====================
get rid of the address_space override in setsockopt v2
setsockopt is the last place in architecture-independ code that still
uses set_fs to force the uaccess routines to operate on kernel pointers.
This series adds a new sockptr_t type that can contained either a kernel
or user pointer, and which has accessors that do the right thing, and
then uses it for setsockopt, starting by refactoring some low-level
helpers and moving them over to it before finally doing the main
setsockopt method.
Note that apparently the eBPF selftests do not even cover this path, so
the series has been tested with a testing patch that always copies the
data first and passes a kernel pointer. This is something that works for
most common sockopts (and is something that the ePBF support relies on),
but unfortunately in various corner cases we either don't use the passed
in length, or in one case actually copy data back from setsockopt, or in
case of bpfilter straight out do not work with kernel pointers at all.
Against net-next/master.
Changes since v1:
- check that users don't pass in kernel addresses
- more bpfilter cleanups
- cosmetic mptcp tweak
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For architectures like x86 and arm64 we don't need the separate bit to
indicate that a pointer is a kernel pointer as the address spaces are
unified. That way the sockptr_t can be reduced to a union of two
pointers, which leads to nicer calling conventions.
The only caveat is that we need to check that users don't pass in kernel
address and thus gain access to kernel memory. Thus the USER_SOCKPTR
helper is replaced with a init_user_sockptr function that does this check
and returns an error if it fails.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factour out a helper to set the IPv6 option headers from
do_ipv6_setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Note that the get case is pretty weird in that it actually copies data
back to userspace from setsockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split ipv6_flowlabel_opt into a subfunction for each action and a small
wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mostly to prepare for cleaning up the callers, as bpfilter by
design can't handle kernel pointers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass a sockptr_t to prepare for set_fs-less handling of the kernel
pointer from bpf-cgroup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a uptr_t type that can hold a pointer to either a user or kernel
memory region, and simply helpers to copy to and from it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpfilter user mode helper processes the optval address using
process_vm_readv. Don't send it kernel addresses fed under
set_fs(KERNEL_DS) as that won't work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split __bpfilter_process_sockopt into a low-level send request routine and
the actual setsockopt hook to split the init time ping from the actual
setsockopt processing.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __user doesn't make sense when casting to an integer type, just
switch to a uintptr_t cast which also removes the need for the __force.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Levkovich says:
====================
TC datapath hash api
Hash based packet classification allows user to set up rules that
provide load balancing of traffic across multiple vports and
for ECMP path selection while keeping the number of rule at minimum.
Instead of matching on exact flow spec, which requires a rule per
flow, user can define rules based on a their hash value and distribute
the flows to different buckets. The number of rules
in this case will be constant and equal to the number of buckets.
The series introduces an extention to the cls flower classifier
and allows user to add rules that match on the hash value that
is stored in skb->hash while assuming the value was set prior to
the classification.
Setting the skb->hash can be done in various ways and is not defined
in this series - for example:
1. By the device driver upon processing an rx packet.
2. Using tc action bpf with a program which computes and sets the
skb->hash value.
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 2 proto ip \
flower hash 0x0/0xf \
action mirred egress redirect dev ens1f0_1
$ tc filter add dev ens1f0_0 ingress \
prio 1 chain 2 proto ip \
flower hash 0x1/0xf \
action mirred egress redirect dev ens1f0_2
v3 -> v4:
*Drop hash setting code leaving only the classidication parts.
Setting the hash will be possible via existing tc action bpf.
v2 -> v3:
*Split hash algorithm option into 2 different actions.
Asym_l4 available via act_skbedit and bpf via new act_hash.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding new cls flower keys for hash value and hash
mask and dissect the hash info from the skb into
the flow key towards flow classication.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Retreive a hash value from the SKB and store it
in the dissector key for future matching.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An imbalanced TX indirection table causes netvsc to have low
performance. This table is created and managed during runtime. To help
better diagnose performance issues caused by imbalanced tables, it needs
make TX indirection tables visible.
Because TX indirection table is driver specified information, so
display it via ethtool register dump.
Signed-off-by: Chi Song <chisong@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy reported compile failure when CONFIG_SYSCTL is not set/enabled:
ERROR: modpost: "sysctl_vals" [drivers/net/vrf.ko] undefined!
Fix by splitting out the sysctl init and cleanup into helpers that
can be set to do nothing when CONFIG_SYSCTL is disabled. In addition,
move vrf_strict_mode and vrf_strict_mode_change to above
vrf_shared_table_handler (code move only) and wrap all of it
in the ifdef CONFIG_SYSCTL.
Update the strict mode tests to check for the existence of the
/proc/sys entry.
Fixes: 33306f1aaf ("vrf: add sysctl parameter for strict mode")
Cc: Andrea Mayer <andrea.mayer@uniroma2.it>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David Ahern <dsahern@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
There isn't a case for 1G SGMII in ice_get_media_type() so add
the handling for it.
Also handle the special case where some direct attach
cables may report that they support 1G SGMII, but
that is erroneous since SGMII is supposed to be a
backplane media type (between a MAC and a PHY). If
the driver doesn't handle this special case then a
user could see the 'Port' in ethtool change from
'Direct attach Copper' to 'Backplane' when they have
forced the speed to 1G, but the cable hasn't changed.
Lastly, change ice_aq_get_phy_caps() to save the
module_type info if the function was called with
ICE_AQC_REPORT_TOPO_CAP. This call uses the media
information to populate the module_type. If no
media is present then the values in module_type
will be 0.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Report AOC types as fiber instead of unknown.
Signed-off-by: Doug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add AQC get link topology handle support. This is needed to determine
Direct Attach (DA) or backplane media type for PHY types that support
either. Get link topology handle cage node type request can be used to
determine if a cage is present or not. If a cage is present for PHY
types that supports both DA and backplane media type, then the media
type is DA, else the media type is backplane.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Rename the low_power_ctrl field to low_power_ctrl_an to be properly
descriptive of it being an autoneg field.
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Firmware now reports AN28, AN32, and AN73. Add a helper and check these new
values and report PHY autoneg capability.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add debug logs for ice_aq_get_phy_caps(), and format
ice_aq_set_phy_cfg() and ice_aq_get_link_info() debug logs to make them
more readable.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When the Port Disable bit is set in the Link Default Override Mask TLV PFA
module in the NVM, Total Port Shutdown mode is supported and enabled. In
this mode, the driver should act as if the link-down-on-close ethtool
private flag is always enabled and dis-allow any change to that flag.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adds functions to check for link override firmware support and get
the override settings for a port. The previously supported/default link
mode was strict mode.
In strict mode link is configured based on get PHY capabilities PHY types
with media.
Lenient mode is now the default link mode. In lenient mode the link is
configured based on get PHY capabilities PHY types without media. This
allows the user to configure link that the media does not report. Limit the
minimum supported link mode to 25G for devices that support 100G, and 1G
for devices that support less than 100G.
Default override is only supported in lenient mode. If default override
is supported and enabled, then default override values are used for
configuring speed and FEC. Default override provide persistent link
settings in the NVM.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Evan Swanson <evan.swanson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After the transition from no media to media FW will clear the
set-phy-cfg data set by the user. Save initial PHY settings and any
settings later requested by the user and use that data to restore PHY
settings on media insertion. Since PHY configuration is now being stored,
replace calls that were calling FW to get the configuration with the saved
copy.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The purpose of this override is to give the user an indication of what
the number of the CPU port is (in DSA, the CPU port is a hardware
implementation detail and not a network interface capable of traffic).
However, it has always failed (by design) at providing this information
to the user in a reliable fashion.
Prior to commit 3369afba1e ("net: Call into DSA netdevice_ops
wrappers"), the behavior was to only override this callback if it was
not provided by the DSA master.
That was its first failure: if the DSA master itself was a DSA port or a
switchdev, then the user would not see the number of the CPU port in
/sys/class/net/eth0/phys_port_name, but the number of the DSA master
port within its respective physical switch.
But that was actually ok in a way. The commit mentioned above changed
that behavior, and now overrides the master's ndo_get_phys_port_name
unconditionally. That comes with problems of its own, which are worse in
a way.
The idea is that it's typical for switchdev users to have udev rules for
consistent interface naming. These are based, among other things, on
the phys_port_name attribute. If we let the DSA switch at the bottom
to start randomly overriding ndo_get_phys_port_name with its own CPU
port, we basically lose any predictability in interface naming, or even
uniqueness, for that matter.
So, there are reasons to let DSA override the master's callback (to
provide a consistent interface, a number which has a clear meaning and
must not be interpreted according to context), and there are reasons to
not let DSA override it (it breaks udev matching for the DSA master).
But, there is an alternative method for users to retrieve the number of
the CPU port of each DSA switch in the system:
$ devlink port
pci/0000:00:00.5/0: type eth netdev swp0 flavour physical port 0
pci/0000:00:00.5/2: type eth netdev swp2 flavour physical port 2
pci/0000:00:00.5/4: type notset flavour cpu port 4
spi/spi2.0/0: type eth netdev sw0p0 flavour physical port 0
spi/spi2.0/1: type eth netdev sw0p1 flavour physical port 1
spi/spi2.0/2: type eth netdev sw0p2 flavour physical port 2
spi/spi2.0/4: type notset flavour cpu port 4
spi/spi2.1/0: type eth netdev sw1p0 flavour physical port 0
spi/spi2.1/1: type eth netdev sw1p1 flavour physical port 1
spi/spi2.1/2: type eth netdev sw1p2 flavour physical port 2
spi/spi2.1/3: type eth netdev sw1p3 flavour physical port 3
spi/spi2.1/4: type notset flavour cpu port 4
So remove this duplicated, unreliable and troublesome method. From this
patch on, the phys_port_name attribute of the DSA master will only
contain information about itself (if at all). If the users need reliable
information about the CPU port they're probably using devlink anyway.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to ice_cfg_phy_fec() requires the caller to perform certain
actions before calling it. Instead of imposing these preconditions move
the operations into the function and perform them ourselves.
Also, fix some style issues in nearby touched code.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Willem de Bruijn