Fix misleading help text for SND_SEQUENCER_OSS config option.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds a mixer control which allows the user to switch the Aux
playback between the internal Aux jack, Wavetable, and Rear Line-In on
Aureon Universe cards.
For switching, a PCA9554 (8-line GPIO with I2C interface) and a 74HC4052
(dual 4-way mux/demux) are used. Output 0 and 1 of the PCA9554 are
connected to the select pins of the 74HC4052. The I2C interface of the
PCA9554 is connected to the card's internal SPI bus which is also used
to control the WM8770 and CS8415. SPI and I2C on the same lines...
To communicate with the PCA9554 the WM8770 and CS8415 are disabled and
an I2C Stop Condition is generated before the Start Condition (needed
for synchronisation because other SPI traffic appear to confuse the
PCA9554). Then a normal I2C data transfer takes place. Programming must
be done ridiculously slow; in theory, 4.7us is the minimum delay time
for normal-speed I2C according to the datasheet, but even with 10us
switching was unreliable. The Windows driver from Terratec does the
programming very slowly, too (checked with an oscilloscope).
PCA9554 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/PCA9554_9554A_6.pdf
74HC4052 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/74HC_HCT4052_4.pdf
Signed-off-by: Maximilian Rehkopf <otakon@gmx.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a new board revision for pcxhr boards, the
PCXHR_CHIPSC_GPI_USERI bit is no more supported.
The cards concerned have a REV01 in their PCI ID.
As the current driver tests this bit and does not load the
first Xilinx binary when it's 1, the card will crash on Xilinx
access over PCI. (the PCI will freeze ....)
The fix (fix to version 1.0.11rc4) works for both REV00 and
REV01 cards.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
process_unsol_events() seems to assume a singlethread one (IOW, racey).
So, this patch uses create_singlethread_workqueue() instead of
create_workqueue().
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for high definition audio on ATI SB600.
Signed-off-by: Felix Kuehling <fkuehlin@ati.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Test the volume of usb audio whether actually it works and adjusts
the resolution value according to it.
Some USB audio devices report a lower resolution than it reacts.
The only possible check is to write and read a volume value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- fix brown-paper-bag locking bug (lock() / return / unlock())
- improve central function snd_m3_update_ptr()
(avoid expensive integer divisions)
- add cpu_relax() to busy-wait I/O loop as recommended
(does this require special macro support in ALSA for older kernels??)
- constify several structs
- spelling updates
Signed-off-by: Andreas Mohr <andi@lisas.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The following patch relative to CVS from 20060324 adds the following
features to the Realtek HDA codec.
1) Define two new pin modes: ALC_PIN_DIR_IN_NOMICBIAS and
ALC_PIN_DIR_INOUT_NOMICBIAS. These can be used with jack mode switch
definitions in mixers to prevent the user being offered the mic bias
options if the hardware doesn't support it.
2) Add the ability to have different input mux definitions for different
ADCs. This is needed because the ALC260 chip uses different mux layouts
for the two onboard ADCs. A new field (num_mux_defs) was added to the
alc_spec and alc_config_preset structures to support this.
3) Adjust numerous comments to make them consistent with the above changes.
4) Utilise the new multi-mux definition functionality for the ALC260 fujitsu
model to allow recording of the mixer output.
5) Utilise the new multi-mux definition functionality for the ALC260 test
model to make the mux selections a little less confusing.
6) Allow the headphone jack of the ALC260 acer model to be retasked in
the mixer.
6) Utilise the new multi-mux definition functionality for the ALC260 acer
model to give access to the mixer output and the retasked headphone
jack.
At this stage the *_NOMICBIAS modes are not used. We have reports that the
"Line" jack of at least some Acer models doesn't pass the bias out, and we
also know that NIDs 0x0f and 0x10 don't seem to accept the mic bias requests
at all. However, I feel we need to collect more evidence on both counts
before committing to the use of *_NOMICBIAS. In the case of the Acers, it's
not clear whether this issue (probably caused by the inclusion of DC
blocking capacitors) affects all Acer models or just a small number. With
the issue with NIDs 0x0f and 0x10 it's unclear whether this is a hardware
bug which will be addressed in later chip revisions or if it's an
intentional restriction. The datasheet makes no mention of the restriction
so at this stage I'm inclined to consider it a hardware bug. Comments in
the source reflect this reasoning.
On a similar theme, the headphone jack of the Fujitsu S7020 also doesn't
appear to pass mic bias voltage. I'm still investigating this however.
With the ability to retask the headphone jack, owners of ALC260-based Acer
laptops should now be able to record 4 channels of audio if they desire. The
multiple mux definitions allow this jack to be presented from both ADCs
(since this mux input is one of those which differs between the muxes).
This patch has been tested on a Fujitsu S7020 laptop and appears to behave
itself both for the "test" and "fujitsu" models. Definitions using only a
single mux specification also work. Other ALC chips should be fine but I
cannot test these myself. The "auto" modes should also continue to function
but again I have not verified this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Attached you'll find an ALSA driver for AdLib FM cards. An AdLib card is
just an OPL2, which was already supported by sound/drivers/opl3, so only
very minimal bus-glue is needed. The patch applies cleanly to both
2.6.16 and 2.6.16-mm1.
The driver has been tested with an actual ancient 8-bit ISA AdLib card
and works fine. It also works fine for an OPL3 {,emulation} as still
found on many ISA soundcards but given that AdLib cards don't have their
own mixer, upping the volume from 0 might be a problem without the card
driver already loaded and driving the OPL3.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Fix possible race of referring the setup hook from the running PCM
- Fix memory leak in an error path of proc write
- Clean up the setup hook parser
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Clean up initialization and destruction of substream instance
Now snd_pcm_open_substream() alone does most initialization jobs.
Add pcm_release callback for cleaning up at snd_pcm_release_substream()
- Tidy up PCM oss code
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Removed from CONFIG_EXPERIMENTAL from CONFIG_SND_CS46XX_NEW_DSP, and
make default to yes. This option works fine for years.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I have just discovered I made an error in the register value set in 'Limit
dmx6fire to 6 dacs' patch (bug1472). The value set should be '2a' not '0a'
as in the original patch, which unintentionally disables the 2nd MPU 401
UART.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Convert the remaining drivers which use pcmcia_release_io or
pcmcia_release_irq, and remove the EXPORT of these symbols.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pcmcia_disable_device(struct pcmcia_device *p_dev) performs the necessary
cleanups upon device or driver removal: it calls the appropriate
pcmcia_release_* functions, and can replace (most) of the current drivers'
_release() functions.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Get rid of unnessesary casts of kmalloc() return value in sound/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vfree() does it's own NULL checking, no need for explicit check before
calling it.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no need to check pointers for NULL before handing them to vfree().
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
vfree() checks for NULL, no need to do it explicitly.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Zach Brown <zab@zabbo.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no need to check the vfree() argument for NULL.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark the f_ops members of inodes as const, as well as fix the
ripple-through this causes by places that copy this f_ops and then "do
stuff" with it.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix some __init/__devinit issues.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed. And fix a __init/__devinit issue.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_card_driver() returns the
number of devices claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_driver() returns the number of devices
claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_driver() returns the number of devices
claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the assumption that pnp_register_driver() returns the number of devices
claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This series of patches removes the assumption that pnp_register_driver()
returns the number of devices claimed. Returning the count is unreliable
because devices may be hot-plugged in the future. (Many devices don't support
hot-plug, of course, but PNP in general does.)
This changes the convention to "zero for success, or a negative error value,"
which matches pci_register_driver(), acpi_bus_register_driver(), and
platform_driver_register().
If drivers need to know the number of devices, they can count calls to their
.probe() methods.
This patch:
Remove the assumption that pnp_register_driver() returns the number of devices
claimed.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sound/oss/sonicvibes.c:421: error: static declaration of hweight32 follows non-static declaration
include/asm-generic/bitops/hweight.h:6: error: previous declaration of hweight32 was here
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's about to go away.
Cc: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compilation for sound/oss/vwsnd.o, by moving li_destroy() above
li_create()
sound/oss/vwsnd.c:275: warning: conflicting types for âli_destroyâ
sound/oss/vwsnd.c:275: error: static declaration of âli_destroyâ follows non-static declaration
sound/oss/vwsnd.c:264: error: previous implicit declaration of âli_destroyâ was here
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/sam/kbuild: (46 commits)
kbuild: remove obsoleted scripts/reference_* files
kbuild: fix make help & make *pkg
kconfig: fix time ordering of writes to .kconfig.d and include/linux/autoconf.h
Kconfig: remove the CONFIG_CC_ALIGN_* options
kbuild: add -fverbose-asm to i386 Makefile
kbuild: clean-up genksyms
kbuild: Lindent genksyms.c
kbuild: fix genksyms build error
kbuild: in makefile.txt note that Makefile is preferred name for kbuild files
kbuild: replace PHONY with FORCE
kbuild: Fix bug in crc symbol generating of kernel and modules
kbuild: change kbuild to not rely on incorrect GNU make behavior
kbuild: when warning symbols exported twice now tell user this is the problem
kbuild: fix make dir/file.xx when asm symlink is missing
kbuild: in the section mismatch check try harder to find symbols
kbuild: fix section mismatch check for unwind on IA64
kbuild: kill false positives from section mismatch warnings for powerpc
kbuild: kill trailing whitespace in modpost & friends
kbuild: small update of allnoconfig description
kbuild: make namespace.pl CROSS_COMPILE happy
...
Trivial conflict in arch/ppc/boot/Makefile manually fixed up
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (21 commits)
BUG_ON() Conversion in drivers/video/
BUG_ON() Conversion in drivers/parisc/
BUG_ON() Conversion in drivers/block/
BUG_ON() Conversion in sound/sparc/cs4231.c
BUG_ON() Conversion in drivers/s390/block/dasd.c
BUG_ON() Conversion in lib/swiotlb.c
BUG_ON() Conversion in kernel/cpu.c
BUG_ON() Conversion in ipc/msg.c
BUG_ON() Conversion in block/elevator.c
BUG_ON() Conversion in fs/coda/
BUG_ON() Conversion in fs/binfmt_elf_fdpic.c
BUG_ON() Conversion in input/serio/hil_mlc.c
BUG_ON() Conversion in md/dm-hw-handler.c
BUG_ON() Conversion in md/bitmap.c
The comment describing how MS_ASYNC works in msync.c is confusing
rcu: undeclared variable used in documentation
fix typos "wich" -> "which"
typo patch for fs/ufs/super.c
Fix simple typos
tabify drivers/char/Makefile
...
'int dev' came out of an 'unsigned char *' - as such, it will not get
a negative value. Thanks Valdis.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Cc: Jaroslav Kysela <perex@suse.cz>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dev should be validated before it is being used as index to array.
Coverity bug #871
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MODULE_PARM was actually breaking: recent gcc version optimize them out as
unused. It's time to replace the last users, which are generally in the
most unloved drivers anyway.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner, contains unlikely() and can better optimized away.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Several media/video and sound drivers include i2c-dev.h while they
don't need it at all. Clean it up.
This header file is really only needed by i2c-dev.c and
compat_ioctl.c, other drivers should never need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Extracted for OSS/Free changes from Ingo's original patches.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the DMA_28BIT_MASK constant in dma-mapping.h
ALSA drivers using this mask are changed to use the new constant.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jaroslav Kysela <perex@suse.cz>
Modules: MIPS AU1x00 driver
AMD Au1x00 ALSA driver causes kernel oops in au1000_init() by trying
to set DMA channel to -1 in yet unallocated audio streams. Here's the
patch that staightens up DMA init/cleanup code.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA generic driver
- Fix autoconfig speaker/hp detection
Now it allows multiple speaker pins (e.g. Dell laptops have such config)
- Use speaker or hp pins if no line-outs are available
This fixes the silence output on recent Dell laptops with STAC9200
(ALSA bug#1843)
- Fix analog/realtek/sigmatel autoconfig parser
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: MIPS AU1x00 driver
AMD Au1x00 ALSA driver doesn't build after the recent code cleanup:
sound/mips/au1x00.c: In function 'au1000_setup_dma_link':
sound/mips/au1x00.c:173: error: 'pointer' undeclared (first use in this function)
sound/mips/au1x00.c:173: error: (Each undeclared identifier is reported only once
sound/mips/au1x00.c:173: error: for each function it appears in.)
sound/mips/au1x00.c: In function 'snd_au1000_hw_params':
sound/mips/au1x00.c:339: warning: implicit declaration of function 'snd_mask_min'
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: USB generic driver
We may leak 'namelist' in sound/usb/usbmixer.c::parse_audio_selector_unit()
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ALSA sequencer
cptr->pool must be non-NULL there, so just the if (cptr->pool) is
superfluous. Thanks Takashi.
Signed-off-by: Eugene Teo <eugene.teo@eugeneteo.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,HDA Codec driver
Added a new model 'laptop-eapd' to AD1986A codec for Samsung R65 and
ASUS A6J laptops.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,HDA Codec driver
Add support for VAIO FE550G and SZ110 laptops with Sigmatel codec (7661).
The new model 'vaio' is added.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: NM256 driver
Treat the nm256 mixer as a write-only device so as to avoid hangs on
initialisation.
Signed-off-by: Florian Schlichting <Florian.Schlichting@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec
Add the pointer to a static volume resolution table to ac97 template,
so that the drivers can define the volume resolution, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Frederik Deweerdt