This removes the code that was added to enable HV KVM to work
on PPC970 processors. The PPC970 is an old CPU that doesn't
support virtualizing guest memory. Removing PPC970 support also
lets us remove the code for allocating and managing contiguous
real-mode areas, the code for the !kvm->arch.using_mmu_notifiers
case, the code for pinning pages of guest memory when first
accessed and keeping track of which pages have been pinned, and
the code for handling H_ENTER hypercalls in virtual mode.
Book3S HV KVM is now supported only on POWER7 and POWER8 processors.
The KVM_CAP_PPC_RMA capability now always returns 0.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=CR/Z
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm-next
Patch queue for ppc - 2014-09-24
New awesome things in this release:
- E500: e6500 core support
- E500: guest and remote debug support
- Book3S: remote sw breakpoint support
- Book3S: HV: Minor bugfixes
Alexander Graf (1):
KVM: PPC: Pass enum to kvmppc_get_last_inst
Bharat Bhushan (8):
KVM: PPC: BOOKE: allow debug interrupt at "debug level"
KVM: PPC: BOOKE : Emulate rfdi instruction
KVM: PPC: BOOKE: Allow guest to change MSR_DE
KVM: PPC: BOOKE: Clear guest dbsr in userspace exit KVM_EXIT_DEBUG
KVM: PPC: BOOKE: Guest and hardware visible debug registers are same
KVM: PPC: BOOKE: Add one reg interface for DBSR
KVM: PPC: BOOKE: Add one_reg documentation of SPRG9 and DBSR
KVM: PPC: BOOKE: Emulate debug registers and exception
Madhavan Srinivasan (2):
powerpc/kvm: support to handle sw breakpoint
powerpc/kvm: common sw breakpoint instr across ppc
Michael Neuling (1):
KVM: PPC: Book3S HV: Add register name when loading toc
Mihai Caraman (10):
powerpc/booke: Restrict SPE exception handlers to e200/e500 cores
powerpc/booke: Revert SPE/AltiVec common defines for interrupt numbers
KVM: PPC: Book3E: Increase FPU laziness
KVM: PPC: Book3e: Add AltiVec support
KVM: PPC: Make ONE_REG powerpc generic
KVM: PPC: Move ONE_REG AltiVec support to powerpc
KVM: PPC: Remove the tasklet used by the hrtimer
KVM: PPC: Remove shared defines for SPE and AltiVec interrupts
KVM: PPC: e500mc: Add support for single threaded vcpus on e6500 core
KVM: PPC: Book3E: Enable e6500 core
Paul Mackerras (2):
KVM: PPC: Book3S HV: Increase timeout for grabbing secondary threads
KVM: PPC: Book3S HV: Only accept host PVR value for guest PVR
1. We were calling clear_flush_young_notify in unmap_one, but we are
within an mmu notifier invalidate range scope. The spte exists no more
(due to range_start) and the accessed bit info has already been
propagated (due to kvm_pfn_set_accessed). Simply call
clear_flush_young.
2. We clear_flush_young on a primary MMU PMD, but this may be mapped
as a collection of PTEs by the secondary MMU (e.g. during log-dirty).
This required expanding the interface of the clear_flush_young mmu
notifier, so a lot of code has been trivially touched.
3. In the absence of shadow_accessed_mask (e.g. EPT A bit), we emulate
the access bit by blowing the spte. This requires proper synchronizing
with MMU notifier consumers, like every other removal of spte's does.
Signed-off-by: Andres Lagar-Cavilla <andreslc@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds kernel side support for software breakpoint.
Design is that, by using an illegal instruction, we trap to hypervisor
via Emulation Assistance interrupt, where we check for the illegal instruction
and accordingly we return to Host or Guest. Patch also adds support for
software breakpoint in PR KVM.
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Powerpc timer implementation is a copycat version of s390. Now that they removed
the tasklet with commit ea74c0ea1b follow this
optimization.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch emulates debug registers and debug exception
to support guest using debug resource. This enables running
gdb/kgdb etc in guest.
On BOOKE architecture we cannot share debug resources between QEMU and
guest because:
When QEMU is using debug resources then debug exception must
be always enabled. To achieve this we set MSR_DE and also set
MSRP_DEP so guest cannot change MSR_DE.
When emulating debug resource for guest we want guest
to control MSR_DE (enable/disable debug interrupt on need).
So above mentioned two configuration cannot be supported
at the same time. So the result is that we cannot share
debug resources between QEMU and Guest on BOOKE architecture.
In the current design QEMU gets priority over guest, this means that if
QEMU is using debug resources then guest cannot use them and if guest is
using debug resource then QEMU can overwrite them.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This are not specific to e500hv but applicable for bookehv
(As per comment from Scott Wood on my patch
"kvm: ppc: bookehv: Added wrapper macros for shadow registers")
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
DCR handling was only needed for 440 KVM. Since we removed it, we can also
remove handling of DCR accesses.
Signed-off-by: Alexander Graf <agraf@suse.de>
We're going to implement guest code interpretation in KVM for some rare
corner cases. This code needs to be able to inject data and instruction
faults into the guest when it encounters them.
Expose generic APIs to do this in a reasonably subarch agnostic fashion.
Signed-off-by: Alexander Graf <agraf@suse.de>
Today the instruction emulator can get called via 2 separate code paths. It
can either be called by MMIO emulation detection code or by privileged
instruction traps.
This is bad, as both code paths prepare the environment differently. For MMIO
emulation we already know the virtual address we faulted on, so instructions
there don't have to actually fetch that information.
Split out the two separate use cases into separate files.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have enough common infrastructure now to resolve GVA->GPA mappings at
runtime. With this we can move our book3s specific helpers to load / store
in guest virtual address space to common code as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
We have a nice API to find the translated GPAs of a GVA including protection
flags. So far we only use it on Book3S, but there's no reason the same shouldn't
be used on BookE as well.
Implement a kvmppc_xlate() version for BookE and clean it up to make it more
readable in general.
Signed-off-by: Alexander Graf <agraf@suse.de>
On book3e, guest last instruction is read on the exit path using load
external pid (lwepx) dedicated instruction. This load operation may fail
due to TLB eviction and execute-but-not-read entries.
This patch lay down the path for an alternative solution to read the guest
last instruction, by allowing kvmppc_get_lat_inst() function to fail.
Architecture specific implmentations of kvmppc_load_last_inst() may read
last guest instruction and instruct the emulation layer to re-execute the
guest in case of failure.
Make kvmppc_get_last_inst() definition common between architectures.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
kvmppc_set_epr() is already defined in asm/kvm_ppc.h, So
rename and move get_epr helper function to same file.
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
[agraf: remove duplicate return]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add and use kvmppc_set_esr() and kvmppc_get_esr() helper functions
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
There are shadow registers like, GSPRG[0-3], GSRR0, GSRR1 etc on
BOOKE-HV and these shadow registers are guest accessible.
So these shadow registers needs to be updated on BOOKE-HV.
This patch adds new macro for get/set helper of shadow register .
Signed-off-by: Bharat Bhushan <Bharat.Bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds code to check that when the KVM_CAP_PPC_ENABLE_HCALL
capability is used to enable or disable in-kernel handling of an
hcall, that the hcall is actually implemented by the kernel.
If not an EINVAL error is returned.
This also checks the default-enabled list of hcalls and prints a
warning if any hcall there is not actually implemented.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
The shared (magic) page is a data structure that contains often used
supervisor privileged SPRs accessible via memory to the user to reduce
the number of exits we have to take to read/write them.
When we actually share this structure with the guest we have to maintain
it in guest endianness, because some of the patch tricks only work with
native endian load/store operations.
Since we only share the structure with either host or guest in little
endian on book3s_64 pr mode, we don't have to worry about booke or book3s hv.
For booke, the shared struct stays big endian. For book3s_64 hv we maintain
the struct in host native endian, since it never gets shared with the guest.
For book3s_64 pr we introduce a variable that tells us which endianness the
shared struct is in and route every access to it through helper inline
functions that evaluate this variable.
Signed-off-by: Alexander Graf <agraf@suse.de>
As part of the support for split core on POWER8, we want to be able to
block splitting of the core while KVM VMs are active.
The logic to do that would be exactly the same as the code we currently
have for inhibiting onlining of secondaries.
Instead of adding an identical mechanism to block split core, rework the
secondary inhibit code to be a "HV KVM is active" check. We can then use
that in both the cpu hotplug code and the upcoming split core code.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Alexander Graf <agraf@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This introduces the H_GET_TCE hypervisor call, which is basically the
reverse of H_PUT_TCE, as defined in the Power Architecture Platform
Requirements (PAPR).
The hcall H_GET_TCE is required by the kdump kernel, which uses it to
retrieve TCEs set up by the previous (panicked) kernel.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Simplify the handling of lazy EE by going directly from fully-enabled
to hard-disabled. This replaces the lazy_irq_pending() check
(including its misplaced kvm_guest_exit() call).
As suggested by Tiejun Chen, move the interrupt disabling into
kvmppc_prepare_to_enter() rather than have each caller do it. Also
move the IRQ enabling on heavyweight exit into
kvmppc_prepare_to_enter().
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
MMIO emulation reads the last instruction executed by the guest
and then emulates. If the guest is running in Little Endian order,
or more generally in a different endian order of the host, the
instruction needs to be byte-swapped before being emulated.
This patch adds a helper routine which tests the endian order of
the host and the guest in order to decide whether a byteswap is
needed or not. It is then used to byteswap the last instruction
of the guest in the endian order of the host before MMIO emulation
is performed.
Finally, kvmppc_handle_load() of kvmppc_handle_store() are modified
to reverse the endianness of the MMIO if required.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
[agraf: add booke handling]
Signed-off-by: Alexander Graf <agraf@suse.de>
drop is_hv_enabled, because that should not be a callback property
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This moves the kvmppc_ops callbacks to be a per VM entity. This
enables us to select HV and PR mode when creating a VM. We also
allow both kvm-hv and kvm-pr kernel module to be loaded. To
achieve this we move /dev/kvm ownership to kvm.ko module. Depending on
which KVM mode we select during VM creation we take a reference
count on respective module
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[agraf: fix coding style]
Signed-off-by: Alexander Graf <agraf@suse.de>
We will use that in the later patch to find the kvm ops handler
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This help us to identify whether we are running with hypervisor mode KVM
enabled. The change is needed so that we can have both HV and PR kvm
enabled in the same kernel.
If both HV and PR KVM are included, interrupts come in to the HV version
of the kvmppc_interrupt code, which then jumps to the PR handler,
renamed to kvmppc_interrupt_pr, if the guest is a PR guest.
Allowing both PR and HV in the same kernel required some changes to
kvm_dev_ioctl_check_extension(), since the values returned now can't
be selected with #ifdefs as much as previously. We look at is_hv_enabled
to return the right value when checking for capabilities.For capabilities that
are only provided by HV KVM, we return the HV value only if
is_hv_enabled is true. For capabilities provided by PR KVM but not HV,
we return the PR value only if is_hv_enabled is false.
NOTE: in later patch we replace is_hv_enabled with a static inline
function comparing kvm_ppc_ops
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch add a new callback kvmppc_ops. This will help us in enabling
both HV and PR KVM together in the same kernel. The actual change to
enable them together is done in the later patch in the series.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[agraf: squash in booke changes]
Signed-off-by: Alexander Graf <agraf@suse.de>
This help ups to select the relevant code in the kernel code
when we later move HV and PR bits as seperate modules. The patch
also makes the config options for PR KVM selectable
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently this is only being done on 64-bit. Rather than just move it
out of the 64-bit ifdef, move it to kvm_lazy_ee_enable() so that it is
consistent with lazy ee state, and so that we don't track more host
code as interrupts-enabled than necessary.
Rename kvm_lazy_ee_enable() to kvm_fix_ee_before_entry() to reflect
that this function now has a role on 32-bit as well.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Older version of power architecture use Real Mode Offset register and Real Mode Limit
Selector for mapping guest Real Mode Area. The guest RMA should be physically
contigous since we use the range when address translation is not enabled.
This patch switch RMA allocation code to use contigous memory allocator. The patch
also remove the the linear allocator which not used any more
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Powerpc architecture uses a hash based page table mechanism for mapping virtual
addresses to physical address. The architecture require this hash page table to
be physically contiguous. With KVM on Powerpc currently we use early reservation
mechanism for allocating guest hash page table. This implies that we need to
reserve a big memory region to ensure we can create large number of guest
simultaneously with KVM on Power. Another disadvantage is that the reserved memory
is not available to rest of the subsystems and and that implies we limit the total
available memory in the host.
This patch series switch the guest hash page table allocation to use
contiguous memory allocator.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds the API for userspace to instantiate an XICS device in a VM
and connect VCPUs to it. The API consists of a new device type for
the KVM_CREATE_DEVICE ioctl, a new capability KVM_CAP_IRQ_XICS, which
functions similarly to KVM_CAP_IRQ_MPIC, and the KVM_IRQ_LINE ioctl,
which is used to assert and deassert interrupt inputs of the XICS.
The XICS device has one attribute group, KVM_DEV_XICS_GRP_SOURCES.
Each attribute within this group corresponds to the state of one
interrupt source. The attribute number is the same as the interrupt
source number.
This does not support irq routing or irqfd yet.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds the ability for userspace to save and restore the state
of the XICS interrupt presentation controllers (ICPs) via the
KVM_GET/SET_ONE_REG interface. Since there is one ICP per vcpu, we
simply define a new 64-bit register in the ONE_REG space for the ICP
state. The state includes the CPU priority setting, the pending IPI
priority, and the priority and source number of any pending external
interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for the ibm,int-on and ibm,int-off RTAS calls to the
in-kernel XICS emulation and corrects the handling of the saved
priority by the ibm,set-xive RTAS call. With this, ibm,int-off sets
the specified interrupt's priority in its saved_priority field and
sets the priority to 0xff (the least favoured value). ibm,int-on
restores the saved_priority to the priority field, and ibm,set-xive
sets both the priority and the saved_priority to the specified
priority value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, we wake up a CPU by sending a host IPI with
smp_send_reschedule() to thread 0 of that core, which will take all
threads out of the guest, and cause them to re-evaluate their
interrupt status on the way back in.
This adds a mechanism to differentiate real host IPIs from IPIs sent
by KVM for guest threads to poke each other, in order to target the
guest threads precisely when possible and avoid that global switch of
the core to host state.
We then use this new facility in the in-kernel XICS code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds in-kernel emulation of the XICS (eXternal Interrupt
Controller Specification) interrupt controller specified by PAPR, for
both HV and PR KVM guests.
The XICS emulation supports up to 1048560 interrupt sources.
Interrupt source numbers below 16 are reserved; 0 is used to mean no
interrupt and 2 is used for IPIs. Internally these are represented in
blocks of 1024, called ICS (interrupt controller source) entities, but
that is not visible to userspace.
Each vcpu gets one ICP (interrupt controller presentation) entity,
used to store the per-vcpu state such as vcpu priority, pending
interrupt state, IPI request, etc.
This does not include any API or any way to connect vcpus to their
ICP state; that will be added in later patches.
This is based on an initial implementation by Michael Ellerman
<michael@ellerman.id.au> reworked by Benjamin Herrenschmidt and
Paul Mackerras.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix typo, add dependency on !KVM_MPIC]
Signed-off-by: Alexander Graf <agraf@suse.de>
For pseries machine emulation, in order to move the interrupt
controller code to the kernel, we need to intercept some RTAS
calls in the kernel itself. This adds an infrastructure to allow
in-kernel handlers to be registered for RTAS services by name.
A new ioctl, KVM_PPC_RTAS_DEFINE_TOKEN, then allows userspace to
associate token values with those service names. Then, when the
guest requests an RTAS service with one of those token values, it
will be handled by the relevant in-kernel handler rather than being
passed up to userspace as at present.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix warning]
Signed-off-by: Alexander Graf <agraf@suse.de>
Enabling this capability connects the vcpu to the designated in-kernel
MPIC. Using explicit connections between vcpus and irqchips allows
for flexibility, but the main benefit at the moment is that it
simplifies the code -- KVM doesn't need vm-global state to remember
which MPIC object is associated with this vm, and it doesn't need to
care about ordering between irqchip creation and vcpu creation.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: add stub functions for kvmppc_mpic_{dis,}connect_vcpu]
Signed-off-by: Alexander Graf <agraf@suse.de>
Hook the MPIC code up to the KVM interfaces, add locking, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[agraf: add stub function for kvmppc_mpic_set_epr, non-booke, 64bit]
Signed-off-by: Alexander Graf <agraf@suse.de>
Instruction emulation return EMULATE_DO_PAPR when it requires
exit to userspace on book3s. Similar return is required
for booke. EMULATE_DO_PAPR reads out to be confusing so it is
renamed to EMULATE_EXIT_USER.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Kernel can only access pages which maps as memory.
So flush only the valid kernel pages.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently kvmppc_core_dequeue_external() takes a struct kvm_interrupt *
argument and does nothing with it, in any of its implementations.
This removes it in order to make things easier for forthcoming
in-kernel interrupt controller emulation code.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch makes the parameter old a const pointer to the old memory
slot and adds a new parameter named change to know the change being
requested: the former is for removing extra copying and the latter is
for cleaning up the code.
Signed-off-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Current kvmppc_booke_handlers uses the same macro (KVM_HANDLER) and
all handlers are considered to be the same size. This will not be
the case if we want to use different macros for different handlers.
This patch improves the kvmppc_booke_handler so that it can
support different macros for different handlers.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
[bharat.bhushan@freescale.com: Substantial changes]
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The External Proxy Facility in FSL BookE chips allows the interrupt
controller to automatically acknowledge an interrupt as soon as a
core gets its pending external interrupt delivered.
Today, user space implements the interrupt controller, so we need to
check on it during such a cycle.
This patch implements logic for user space to enable EPR exiting,
disable EPR exiting and EPR exiting itself, so that user space can
acknowledge an interrupt when an external interrupt has successfully
been delivered into the guest vcpu.
Signed-off-by: Alexander Graf <agraf@suse.de>
When running on top of pHyp, the hypercall instruction "sc 1" goes
straight into pHyp without trapping in supervisor mode.
So if we want to support PAPR guest in this configuration we need to
add a second way of accessing PAPR hypercalls, preferably with the
exact same semantics except for the instruction.
So let's overlay an officially reserved instruction and emulate PAPR
hypercalls whenever we hit that one.
Signed-off-by: Alexander Graf <agraf@suse.de>
Mask high 32 bits of effective address in emulation layer for guests running
in 32-bit mode.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: fix indent]
Signed-off-by: Alexander Graf <agraf@suse.de>
Add emulation helper for getting instruction ea and refactor tlb instruction
emulation to use it.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
[agraf: keep rt variable around]
Signed-off-by: Alexander Graf <agraf@suse.de>
A new ioctl, KVM_PPC_GET_HTAB_FD, returns a file descriptor. Reads on
this fd return the contents of the HPT (hashed page table), writes
create and/or remove entries in the HPT. There is a new capability,
KVM_CAP_PPC_HTAB_FD, to indicate the presence of the ioctl. The ioctl
takes an argument structure with the index of the first HPT entry to
read out and a set of flags. The flags indicate whether the user is
intending to read or write the HPT, and whether to return all entries
or only the "bolted" entries (those with the bolted bit, 0x10, set in
the first doubleword).
This is intended for use in implementing qemu's savevm/loadvm and for
live migration. Therefore, on reads, the first pass returns information
about all HPTEs (or all bolted HPTEs). When the first pass reaches the
end of the HPT, it returns from the read. Subsequent reads only return
information about HPTEs that have changed since they were last read.
A read that finds no changed HPTEs in the HPT following where the last
read finished will return 0 bytes.
The format of the data provides a simple run-length compression of the
invalid entries. Each block of data starts with a header that indicates
the index (position in the HPT, which is just an array), the number of
valid entries starting at that index (may be zero), and the number of
invalid entries following those valid entries. The valid entries, 16
bytes each, follow the header. The invalid entries are not explicitly
represented.
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix documentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
Paul Mackerras