ovl->enable/disable are meant to be synchronous so that they can handle
the configuration of fifo sizes. The current kernel doesn't configure
fifo sizes yet, and so the code doesn't need to block to function (from
omapdss driver's perspective).
However, for the users of omapdss a non-blocking ovl->disable is
confusing, because they don't know when the memory area is not used
any more.
Furthermore, when the fifo size configuration is added in the next merge
window, the change from non-blocking to blocking could cause side
effects to the users of omapdss. So by making the functions block
already will keep them behaving in the same manner.
And, while not the main purpose of this patch, this will also remove the
compile warning:
drivers/video/omap2/dss/apply.c:350: warning:
'wait_pending_extra_info_updates' defined but not used
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
panel-dvi uses i2c, but the Kconfig didn't have dependency on I2C. Add
it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
bits are all for devices that still need to get set up in board code.
Only three platforms are in this set of fixes: omap2+, pxa and lpc32xx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ElaK
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Arnd Bergmann says:
"Another set of arm-soc bug fixes on top of v3.3-rc5. The few larger
bits are all for devices that still need to get set up in board code.
Only three platforms are in this set of fixes: omap2+, pxa and lpc32xx."
* tag 'fixes-3.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (22 commits)
ARM: LPC32xx: serial.c: Fixed loop limit
ARM: LPC32xx: serial.c: HW bug workaround
ARM: LPC32xx: irq.c: Clear latched event
ARM: LPC32xx: Fix interrupt controller init
ARM: LPC32xx: Fix irq on GPI_28
ARM: OMAP2: fix mailbox init code
ARM: OMAP2+: gpmc-smsc911x: add required smsc911x regulators
ARM: OMAP1: Fix out-of-bounds array access for Innovator
OMAP3 EVM: remove out-of-bounds array access of gpio_leds
ARM: OMAP: Fix build error when mmc_omap is built as module
ARM: OMAP: Fix kernel panic with HSMMC when twl4030_gpio is a module
pxa/hx4700: add platform device and I2C info for AK4641 codec
arch/arm/mach-pxa/: included linux/gpio.h twice
arch/arm/mach-mmp/: some files include some headers twice
ARM: pxa: fix error handling in pxa2xx_drv_pcmcia_probe
ARM: pxa: fix including linux/gpio.h twice
ARM: pxa: fix mixed declarations and code in sharpsl_pm
ARM: pxa: fix wrong parsing gpio event on spitz
ARM: OMAP2+: usb-host: fix compile warning
ARM: OMAP4: Move the barrier memboclk_steal() as part of reserve callback
...
tg3_get_stats64() takes tp->lock when dealing with non-serdes bcm5700
and bcm5701 devices. However, functions that call tg3_halt() have
already acquired tp->lock. When tg3_get_stats64() is called in
tg3_halt(), deadlock will occur.
This patch fixes the problem by separating the stat gathering code into
a new tg3_get_nstats() function. tg3_get_stats64() is recoded to call
this function and take tp->lock. The code that takes tp->lock in
tg3_calc_crc_errors() has been removed. Function signatures have been
cleaned up too.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit
"mwifiex: clear previous security setting during association"
fixes association failure problems observed in some corner cases
by clearing previous security setting before each association.
We should reset encryption mode flag as well. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nicolas Cavallari discovered that carl9170 has some
serious problems delivering data to sleeping stations.
It turns out that the driver was not honoring two
important flags (IEEE80211_TX_CTL_POLL_RESPONSE and
IEEE80211_TX_CTL_CLEAR_PS_FILT) which are set on
frames that should be sent although the receiving
station is still in powersave mode.
Cc: stable <stable@vger.kernel.org>
Reported-by: Nicolas Cavallari <Nicolas.Cavallari@lri.fr>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Access Point mode, when transmitting a packet, if the destination
station is in powersave mode, we abort transmitting the packet to the
device queue, but we do not reclaim the allocated memory. Given enough
packets, we can go in a state where there is no packet on the device
queue, but we think the device has no memory left, so no packet gets
transmitted, connections breaks and the AP stops working.
This undo the allocation done in the TX path when the station is in
power-save mode.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bo is removed from the list at the top of
radeon_vm_bo_rmv(), but then the list is used
in radeon_vm_bo_update_pte() to look up the vm.
remove the bo_list entry at the end of the
function instead.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <j.glisse@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Without this fix the driver randomly treats
textures as arrays and I'm really wondering
why gcc isn't complaining about it.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Need to call ExternalEncoderControl to set up DDC before
trying to get an EDID for all DP bridge chips (including
DP to LVDS).
Also remove redundant encoder assignment.
V2: fix typo in commit message.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit dcfb748422 ([WATCHDOG] fix book E watchdog to take
WDIOC_SETTIMEOUT arg in seconds) fixed SETTIMEOUT ioctl
to use seconds as a parameter instead of some hardware-specific
"period", but missed to apply similar changes to GETTIMEOUT,
so it still returns "period" value. Let's fix it!
Also, while at it, make SETTIMEOUT ioctl return real timeout
value as it should do according to the documentation.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
For the F75387, the register holding the current PWM duty cycle value is
r/o; changing it requires writing to the fan expect register instead.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Simplified function parameters]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Included module.h explicitly to resolve the macros THIS_MODULE and
MODULE_LICENSE. This avoids compilations errors as those defines were not
declared.
Signed-off-by: Henrique Camargo <henrique@henriquecamargo.com>
Signed-off-by: Diogo Luvizon <diogoluvizon@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All the fixes are for the OMAP IOMMU driver. The first patch is the
biggest one. It fixes the calls of the function omap_find_iovm_area() in
the omap-iommu-debug module which expects a 'struct device' parameter
since commit fabdbca instead of an omap_iommu handle. The
omap-iommu-debug code still passed the handle to the function which
caused a crash.
The second patch fixes a NULL pointer dereference in the OMAP code and
the third patch makes sure that the omap-iommu is initialized before the
omap-isp driver, which relies on the iommu. The last patch is only a
workaround until defered probing is implemented.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPTK9LAAoJECvwRC2XARrjfLkP/3A8wPy0ALLZ3nbRT2S/9CkL
MyNBI7+J8aqnWHQzyiTryLOzyqrUwBPS5wB/KRg6PUAAiwEZGPc5yZlpIHE+8RwP
ze5JAfddox1XRisQ8A8yJWFnvC/KAeMgAiiFn+egnxQlIZUujzgK/SIzTKyFXGtB
T+7utXB/U0T/GygYYTEJo9gU41NvAyWc8Ji6Uin48RTLRHZ74IQdMAEgf1GsAsvp
CsDrBXqgziKEfkcDYhwRcw3teaMX8gUwnvL4Qm33iUpE4sHLW38l0gVaFPWlMEjr
4OTHWLGrNI+TkvSZyTXXXRH+BTZrzW2RisfYpdCaHbjh0XRJvN4CpOChwSewVF7P
1K4uE/cfV66mOzAecR54v0DazUAuVewmDoXzouLdsT6RRTe4nhSev/821odmHDLm
1zh2WcKMwmiKldbtWnSGghiN3hUzP9yPNUEIc7CmEGwOyTjlIkYdQNI5BhpPY+fd
SoMNzwknIW4qdJJoFw/et9z/sXuqjPFQ2Xuhc6HfGOmODNcZeQ4b1/l2J1ygka0y
hIOjOVFNx1K9pfkDkmsXPFL1xMuWls7qUpcY8zVimE5Z3VPs9EowoJ3ZWK1XH0tZ
tJdntNPfsufRnlqAyqqDKuutXavILwnTLRdeEH6SD4YwKlIxiOrLLLJKlUEWCD0B
RUhyr3i8qqtFm4o9j36K
=aclV
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v3.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
IOMMU fixes for Linux 3.3-rc5
All the fixes are for the OMAP IOMMU driver. The first patch is the
biggest one. It fixes the calls of the function omap_find_iovm_area() in
the omap-iommu-debug module which expects a 'struct device' parameter
since commit fabdbca instead of an omap_iommu handle. The
omap-iommu-debug code still passed the handle to the function which
caused a crash.
The second patch fixes a NULL pointer dereference in the OMAP code and
the third patch makes sure that the omap-iommu is initialized before the
omap-isp driver, which relies on the iommu. The last patch is only a
workaround until defered probing is implemented.
* tag 'iommu-fixes-v3.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
ARM: OMAP: make iommu subsys_initcall to fix builtin omap3isp
iommu/omap: fix NULL pointer dereference
iommu/omap: fix erroneous omap-iommu-debug API calls
Probe function of s3c2410 watchdog calls request_irq before initializing
required value (wdt_count). This incurs resetting watchdog counter value
and watchdog-reboot during booting up.
This patch addresses such an issue by calling request_irq later.
Error handling in probe function and calling oder in remove function are
also revised accordingly.
Reported-by: Chanwoo Park <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
1. address has to be page aligned.
2. set_memory_x uses page size argument, not size.
Bug causes with following commit:
commit da28179b4e90dda56912ee825c7eaa62fc103797
Author: Mingarelli, Thomas <Thomas.Mingarelli@hp.com>
Date: Mon Nov 7 10:59:00 2011 +0100
watchdog: hpwdt: Changes to handle NX secure bit in 32bit path
commit e67d668e14 upstream.
This patch makes use of the set_memory_x() kernel API in order
to make necessary BIOS calls to source NMIs.
Signed-off-by: Maxim Uvarov <maxim.uvarov@oracle.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable <stable@vger.kernel.org>
Broken by commit 6ef84509f3 for users
passing a request with non-zero 'nbytes' field, like e.g. testmgr.
Cc: <stable@kernel.org> # 3.0+
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: Remove use of the autoreported ringbuffer HEAD position
drm/i915: Prevent a machine hang by checking crtc->active before loading lut
drm/i915: fix operator precedence when enabling RC6p
drm/i915: fix a sprite watermark computation to avoid divide by zero if xpos<0
drm/i915: fix mode set on load pipe. (v2)
This is a revert of 6aa56062ea.
This was originally introduced to workaround reads of the ringbuffer
registers returning 0 on SandyBridge causing hangs due to ringbuffer
overflow. The root cause here was reads through the GT powerwell require
the forcewake dance, something we only learnt of later. Now it appears
that reading the reported head position from the HWS is returning
garbage, leading once again to hangs.
For example, on q35 the autoreported head reports:
[ 217.975608] head now 00010000, actual 00010000
[ 436.725613] head now 00200000, actual 00200000
[ 462.956033] head now 00210000, actual 00210010
[ 485.501409] head now 00400000, actual 00400020
[ 508.064280] head now 00410000, actual 00410000
[ 530.576078] head now 00600000, actual 00600020
[ 553.273489] head now 00610000, actual 00610018
which appears reasonably sane. In contrast, if we look at snb:
[ 141.970680] head now 00e10000, actual 00008238
[ 141.974062] head now 02734000, actual 000083c8
[ 141.974425] head now 00e10000, actual 00008488
[ 141.980374] head now 032b5000, actual 000088b8
[ 141.980885] head now 03271000, actual 00008950
[ 142.040628] head now 02101000, actual 00008b40
[ 142.180173] head now 02734000, actual 00009050
[ 142.181090] head now 00000000, actual 00000ae0
[ 142.183737] head now 02734000, actual 00009050
In addition, the automatic reporting of the head position is scheduled
to be defeatured in the future. It has no more utility, remove it.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45492
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch (as1531) adds a NOGET quirk for the Slim+ keyboard marketed
by AIREN. This keyboard seems to have a lot of bugs; NOGET works
around only one of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: okias <d.okias@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Use system timestamps if the timestamp can't be computed from the data
sent by the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since 9e6c643b (phy/fixed: use an unique MDIO bus name) the name of the fixed
PHY bus is "fixed-0". Teach of_phy_connect_fixed_link() the new name.
Tested on a P1020RDB PowerPC system.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
drivers/of/fdt.c included 'asm/setup.h' twice, remove the duplicate.
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The new is_compat_task() define for the !COMPAT case in
include/linux/compat.h conflicts with a similar define in
arch/s390/include/asm/compat.h.
This is the minimal patch which fixes the build issues.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/parisc/iommu-helpers.h:62: error: implicit declaration of function 'prefetchw'
make[3]: *** [drivers/parisc/sba_iommu.o] Error 1
drivers/parisc/iommu-helpers.h needs to #include <linux/prefetch.h>
where prefetchw is declared.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
omap3isp depends on omap's iommu and will fail to probe if
initialized before it (which always happen if they are builtin).
Make omap's iommu subsys_initcall as an interim solution until
the probe deferral mechanism is merged.
Reported-by: James <angweiyang@gmail.com>
Debugged-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable <stable@vger.kernel.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
1) ICMP sockets leave err uninitialized but we try to return it for the
unsupported MSG_OOB case, reported by Dave Jones.
2) Add new Zaurus device ID entries, from Dave Jones.
3) Pointer calculation in hso driver memset is wrong, from Dan
Carpenter.
4) ks8851_probe() checks unsigned value as negative, fix also from Dan
Carpenter.
5) Fix crashes in atl1c driver due to TX queue handling, from Eric
Dumazet. I anticipate some TX side locking fixes coming in the near
future for this driver as well.
6) The inline directive fix in Bluetooth which was breaking the build
only with very new versions of GCC, from Johan Hedberg.
7) Fix crashes in the ATP CLIP code due to ARP cleanups this merge
window, reported by Meelis Roos and fixed by Eric Dumazet.
8) JME driver doesn't flush RX FIFO correctly, from Guo-Fu Tseng.
9) Some ip6_route_output() callers test the return value for NULL, but
this never happens as the convention is to return a dst entry with
dst->error set. Fixes from RonQing Li.
10) Logitech Harmony 900 should be handled by zaurus driver not
cdc_ether, update white lists and black lists accordingly. From
Scott Talbert.
11) Receiving from certain kinds of devices there won't be a MAC header,
so there is no MAC header to fixup in the IPSEC code, and if we try
to do it we'll crash. Fix from Eric Dumazet.
12) Port type array indexing off-by-one in mlx4 driver, fix from Yevgeny
Petrilin.
13) Fix regression in link-down handling in davinci_emac which causes
all RX descriptors to be freed up and therefore RX to wedge
completely, from Christian Riesch.
14) It took two attempts, but ctnetlink soft lockups seem to be
cured now, from Pablo Neira Ayuso.
15) Endianness bug fix in ENIC driver, from Santosh Nayak.
16) The long ago conversion of the PPP fragmentation code over to
abstracted SKB list handling wasn't perfect, once we get an
out of sequence SKB we don't flush the rest of them like we
should. From Ben McKeegan.
17) Fix regression of ->ip_summed initialization in sfc driver.
From Ben Hutchings.
18) Bluetooth timeout mistakenly using msecs instead of jiffies,
from Andrzej Kaczmarek.
19) Using _sync variant of work cancellation results in deadlocks,
use the non _sync variants instead. From Andre Guedes.
20) Bluetooth rfcomm code had reference counting problems leading
to crashes, fix from Octavian Purdila.
21) The conversion of netem over to classful qdisc handling added
two bugs to netem_dequeue(), fixes from Eric Dumazet.
22) Missing pci_iounmap() in ATM Solos driver. Fix from Julia Lawall.
23) b44_pci_exit() should not have __exit tag since it's invoked from
non-__exit code. From Nikola Pajkovsky.
24) The conversion of the neighbour hash tables over to RCU added a
race, fixed here by adding the necessary reread of tbl->nht, fix
from Michel Machado.
25) When we added VF (virtual function) attributes for network device
dumps, this potentially bloats up the size of the dump of one
network device such that the dump size is too large for the buffer
allocated by properly written netlink applications.
In particular, if you add 255 VFs to a network device, parts of
GLIBC stop working.
To fix this, we add an attribute that is used to turn on these
extended portions of the network device dump. Sophisticaed
applications like 'ip' that want to see this stuff will be changed
to set the attribute, whereas things like GLIBC that don't care
about VFs simply will not, and therefore won't be busted by the
mere presence of VFs on a network device.
Thanks to the tireless work of Greg Rose on this fix.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (53 commits)
sfc: Fix assignment of ip_summed for pre-allocated skbs
ppp: fix 'ppp_mp_reconstruct bad seq' errors
enic: Fix endianness bug.
gre: fix spelling in comments
netfilter: ctnetlink: fix soft lockup when netlink adds new entries (v2)
Revert "netfilter: ctnetlink: fix soft lockup when netlink adds new entries"
davinci_emac: Do not free all rx dma descriptors during init
mlx4_core: Fixing array indexes when setting port types
phy: IC+101G and PHY_HAS_INTERRUPT flag
netdev/phy/icplus: Correct broken phy_init code
ipsec: be careful of non existing mac headers
Move Logitech Harmony 900 from cdc_ether to zaurus
hso: memsetting wrong data in hso_get_count()
netfilter: ip6_route_output() never returns NULL.
ethernet/broadcom: ip6_route_output() never returns NULL.
ipv6: ip6_route_output() never returns NULL.
jme: Fix FIFO flush issue
atm: clip: remove clip_tbl
ipv4: ping: Fix recvmsg MSG_OOB error handling.
rtnetlink: Fix problem with buffer allocation
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=YJz+
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Couple of minor driver fixes.
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (max34440) Fix resetting temperature history
hwmon: (f75375s) Fix register write order when setting fans to full speed
hwmon: (ads1015) Fix file leak in probe function
hwmon: (max6639) Fix PPR register initialization to set both channels
hwmon: (max6639) Fix FAN_FROM_REG calculation
It used to be that minors where 8 bit. But now they
are actually 20 bit. So the fix is simplicity itself.
I've tested with 300 devices and all user-mode utils
work just fine. I have also mechanically added 10,000
to the ida (so devices are /dev/osd10000, /dev/osd10001 ...)
and was able to mkfs an exofs filesystem and access osds
from user-mode.
All the open-osd user-mode code uses the same library
to access devices through their symbolic names in
/dev/osdX so I'd say it's pretty safe. (Well tested)
This patch is very important because some of the systems
that will be deploying the 3.2 pnfs-objects code are larger
than 64 OSDs and will stop to work properly when reaching
that number.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When pre-allocating skbs for received packets, we set ip_summed =
CHECKSUM_UNNCESSARY. We used to change it back to CHECKSUM_NONE when
the received packet had an incorrect checksum or unhandled protocol.
Commit bc8acf2c8c ('drivers/net: avoid
some skb->ip_summed initializations') mistakenly replaced the latter
assignment with a DEBUG-only assertion that ip_summed ==
CHECKSUM_NONE. This assertion is always false, but it seems no-one
has exercised this code path in a DEBUG build.
Fix this by moving our assignment of CHECKSUM_UNNECESSARY into
efx_rx_packet_gro().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPSByoAAoJEDeqqVYsXL0M3CAIAJT740lwOyc9hyIBarZiZcZj
Ib9rPPppThKYvbo8w6Q6xITNTocohSnmPnjbfXZzN4nLrp1Xbzi6A4YLSeY3oxwE
t11LOMnXYPgCOCNZA3iJ4WadVbfs4Id6PWWZPnifWl6rZ2mhvtWmkCNzayY0Kv2t
WuX0j8ds0KgDG6xpfXKoXvHeNuEDJ5aZF/gtI1kmo1eilwPjlovCjsEWetHr/FQA
0jIKFdgf/nZ1ENZU0ztqGd/Q3er6t7G9qS7cFxUa4fWsqG+8Kl+KIk2PHDLL1QHu
tlYtaGm5kbh5d2tfzAD4HJZqJRw2LQ6U1gqofoAKS7JbqYPUJZDoERQtWZUpoj4=
=GZJg
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6
SCSI fixes on 20120224:
"This is a set of assorted bug fixes for power management, mpt2sas,
ipr, the rdac device handler and quite a big chunk for qla2xxx (plus a
use after free of scsi_host in scsi_scan.c). "
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_dh_rdac: Fix for unbalanced reference count
[SCSI] scsi_pm: Fix bug in the SCSI power management handler
[SCSI] scsi_scan: Fix 'Poison overwritten' warning caused by using freed 'shost'
[SCSI] qla2xxx: Update version number to 8.03.07.13-k.
[SCSI] qla2xxx: Proper detection of firmware abort error code for ISP82xx.
[SCSI] qla2xxx: Remove resetting memory during device initialization for ISP82xx.
[SCSI] qla2xxx: Complete mailbox command timedout to avoid initialization failures during next reset cycle.
[SCSI] qla2xxx: Remove check for null fcport from host reset handler.
[SCSI] qla2xxx: Correct out of bounds read of ISP2200 mailbox registers.
[SCSI] qla2xxx: Remove errant clearing of MBX_INTERRUPT flag during CT-IOCB processing.
[SCSI] qla2xxx: Clear options-flags while issuing stop-firmware mbx command.
[SCSI] qla2xxx: Add an "is reset active" helper.
[SCSI] qla2xxx: Add check for null fcport references in qla2xxx_queuecommand.
[SCSI] qla2xxx: Propagate up abort failures.
[SCSI] isci: Fix NULL ptr dereference when no firmware is being loaded
[SCSI] ipr: fix eeh recovery for 64-bit adapters
[SCSI] mpt2sas: Fix mismatch in mpt2sas_base_hard_reset_handler() mutex lock-unlock
This patch fixes a (mostly cosmetic) bug introduced by the patch
'ppp: Use SKB queue abstraction interfaces in fragment processing'
found here: http://www.spinics.net/lists/netdev/msg153312.html
The above patch rewrote and moved the code responsible for cleaning
up discarded fragments but the new code does not catch every case
where this is necessary. This results in some discarded fragments
remaining in the queue, and triggering a 'bad seq' error on the
subsequent call to ppp_mp_reconstruct. Fragments are discarded
whenever other fragments of the same frame have been lost.
This can generate a lot of unwanted and misleading log messages.
This patch also adds additional detail to the debug logging to
make it clearer which fragments were lost and which other fragments
were discarded as a result of losses. (Run pppd with 'kdebug 1'
option to enable debug logging.)
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware generates an interrupt for every completed command in the
queue while the code assumed that it will only generate one interrupt
when the queue is empty. So, explicitly check if the queue is really
empty. This patch fixed problems which occurred due to high traffic on
the bus. While we are here, move the completion-initialization after the
parameter error checking.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Cc: stable@kernel.org
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] hdpvr: update picture controls to support firmware versions > 0.15
[media] wl128x: fix build errors when GPIOLIB is not enabled
[media] hdpvr: fix race conditon during start of streaming
[media] omap3isp: Fix crash caused by subdevs now having a pointer to devnodes
[media] imon: don't wedge hardware after early callbacks
Before loading the lut (gamma), check the active state of intel_crtc,
otherwise at least on gen2 hang ensue.
This is reproducible in Xorg via:
xset dpms force off
then
xgamma -rgamma 2.0 # freeze.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=44505
Signed-off-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As noticed by Torsten Kaiser, the operator precedence can play tricks with
us here.
CC: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk9HE98ACgkQGkmNcg7/o7g4+QCfYIcWunicH7+tLMjH/h5MgHq2
S5EAoJdIKyAPfV1tsIY0ykJZQP+H4t4X
=QqTI
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
SuperH fixes for 3.3-rc5
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix sh2a build error for CONFIG_CACHE_WRITETHROUGH
sh: modify a resource of sh_eth_giga1_resources in board-sh7757lcr
arch/sh: remove references to cpu_*_map.
sh: Fix typo in pci-sh7780.c
sh: add platform_device for SPI1 in setup-sh7757
sh: modify resource for SPI0 in setup-sh7757
sh: se7724: fix compile breakage
sh: clkfwk: bugfix: use clk_reparent() for div6 clocks
sh: clock-sh7724: fixup sh_fsi clock settings
sh: sh7757lcr: update to the new MMCIF DMA configuration
sh: fix the sh_mmcif_plat_data in board-sh7757lcr
video: pvr2fb: Fix up spurious section mismatch warnings.
sh: Defer to asm-generic/device.h.
Temperature history is reset by writing 0x8000 into the peak temperature
register, not 0xffff.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Adapt omap-iommu-debug to the latest omap-iommu API changes, which
were introduced by commit fabdbca "iommu/omap: eliminate the public
omap_find_iommu_device() method".
In a nutshell, iommu users are not expected to provide the omap_iommu
handle anymore - instead, iommus are attached using their user's device
handle.
omap-iommu-debug is a hybrid beast though: it invokes both public and
private omap iommu API, so fix it as necessary (otherwise a crash
is imminent).
Note: omap-iommu-debug is a bit disturbing, as it fiddles with internal
omap iommu data and requires exposing API which is otherwise not needed.
It should better be more tightly coupled with omap-iommu, to prevent
further bit rot and avoid exposing redundant API. Naturally that's out
of scope for the -rc cycle, so for now just fix the obvious.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Joerg Roedel <Joerg.Roedel@amd.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
On m68k:
drivers/input/misc/twl4030-vibra.c:175:5: warning: "CONFIG_PM" is not
defined
We should use #ifdef instead of #if and also check CONFIG_PM_SLEEP
instead of CONFIG_PM.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 509f87c5f5 (evdev - do not block waiting for an event if fd
is nonblock) created a code path were it was possible to use retval
uninitialized.
This could lead to the xorg evdev input driver getting corrupt data
and refusing to work with log messages like
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
(for drivers auo-pixcir-ts and gpio-keys).
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
ALPS touchpad detection fails if some buttons of ALPS are pressed.
The reason is that the "E6" query response byte is different from
what is expected.
This was tested on a Toshiba Portege R500.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Akio Idehara <zbe64533@gmail.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch fixes a regression that was introduced by
commit 0a5f384677
davinci_emac: Add Carrier Link OK check in Davinci RX Handler
Said commit adds a check whether the carrier link is ok. If the link is
not ok, the skb is freed and no new dma descriptor added to the rx dma
channel. This causes trouble during initialization when the carrier
status has not yet been updated. If a lot of packets are received while
netif_carrier_ok returns false, all dma descriptors are freed and the
rx dma transfer is stopped.
The bug occurs when the board is connected to a network with lots of
traffic and the ifconfig down/up is done, e.g., when reconfiguring
the interface with DHCP.
The bug can be reproduced by flood pinging the davinci board while doing
ifconfig eth0 down
ifconfig eth0 up
on the board.
After that, the rx path stops working and the overrun value reported
by ifconfig is counting up.
This patch reverts commit 0a5f384677
and instead issues warnings only if cpdma_chan_submit returns -ENOMEM.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Cc: <stable@vger.kernel.org>
Cc: Hegde, Vinay <vinay.hegde@ti.com>
Cc: Cyril Chemparathy <cyril@ti.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the documentation calls this bit "Reserved" it has to be set
to 0 for correct modesetting on IGA1.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
VX900 can do hardware scaling for both IGAs in contrast to previous
hardware which could do it only for IGA2. This patch ensures that
we set the parameter for IGA2 and not for IGA1. This fixes hardware
scaling on VX900 until we have the infrastructure to support it for
both IGAs.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: stable@vger.kernel.org
This patch adds the PHY_HAS_INTERRUPT flag for IC+101 device series.
Also the patch does a simple dity-up to signal that
the driver actually is for IP101A LF and IP101G devices.
In fact, these are two similar PHYs that have the same IDs
and mainly differ for the EEE capability supported in the
G series.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for ip1001_config_init() was totally broken if you were not
using RGMII. Instead of returning an error code or zero it actually
returned the value in the IP1001_SPEC_CTRL_STATUS_2 register. It was
also trying to set the IP1001_APS_ON bit , but never actually wrote
back the register.
The error checking was also incorrect in both this function and the
reset function, so this patch fixes that up in a consistent fashion.
Signed-off-by: David McKay <david.mckay@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In regular use block-ack timeouts can happen so it does not make
sense to fill the log with these messages.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The A-MPDU code checked against a retry limit, but it was using
the wrong variable to do so. This patch fixes this to assure
proper retry mechanism.
This problem had a side-effect causing the mac80211 flush callback
to remain waiting forever as well. That side effect has been fixed
by commit by Stanislaw Gruszka:
commit f96b08a7e6
Date: Tue Jan 17 12:38:50 2012 +0100
brcmsmac: fix tx queue flush infinite loop
Reference:
https://bugzilla.kernel.org/show_bug.cgi?id=42576
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Alwin Beukers <alwin@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BenH says:
'Here are a few more powerpc bits for you. A stupid regression I
introduced with my previous commit to "fix" program check exceptions
(brown paper bag for me), fix the cpuidle default, a bug fix for
something that isn't strictly speaking a regression but some upstream
changes causes it to show in lockdep now while it didn't before, and
finally a trivial one for rusty to make his life easier later on
removing the old cpumask cruft. '
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix various issues with return to userspace
cpuidle: Default y on powerpc pSeries
powerpc: Fix program check handling when lockdep is enabled
powerpc: Remove references to cpu_*_map
When setting overlay position with x<0, it will divide 0 and make drm
driver crash.
Signed-off-by: Hai Lan <hai.lan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
irq_base of the tps65912 irq platform data should be
initialized with the board provided irq_base data.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The code is currently always checking the first resource of every
device only (several times.) This has been broken since the ACPI check
was added in February 2010 in commit
91fedede03.
Fix the check to run on each resource individually, once.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Booted my i965 machine and it started printing the unsupported pixel
format of 0 message (once I added content to it).
Oh looksie here, we pass 0. fix.
v2: compile it.
Buzilla: https://bugs.freedesktop.org/show_bug.cgi?id=45966
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By hwmon sysfs interface convention, setting pwm_enable to zero sets a fan
to full speed. In the f75375s driver, this need be done by enabling
manual fan control, plus duty mode for the F875387 chip, and then setting
the maximum duty cycle. Fix a bug where the two necessary register writes
were swapped, effectively discarding the setting to full-speed.
Signed-off-by: Nikolaus Schulz <mail@microschulz.de>
Cc: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
An error while creating sysfs attribute files in the driver's probe function
results in an error abort, but already created files are not removed. This patch
fixes the problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Cc: Dirk Eibach <eibach@gdsys.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
The "OMAPDSS: HDMI: PHY burnout fix" commit switched the HDMI driver
over to using a GPIO for plug detect. Unfortunately the ->detect()
method was not also updated, causing HDMI to no longer work for the
omapdrm driver (because it would actually check if a connection was
detected before attempting to enable display).
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For DSS clock domain to transition from idle to active state. It's necessary
to enable the optional clock DSS_FCLK before we enable the module using the
MODULEMODE bits in the clock domain's CM_DSS_DSS_CLKCTRL register.
This sequence was not followed correctly for the 'dss_hdmi' hwmod and it led
to DSS clock domain not getting out of idle when pm_runtime_get_sync() was
called for hdmi's platform device.
Since the clock domain failed to change it's state to active, the hwmod code
disables any clocks it had enabled before for this hwmod. This led to the clock
'dss_48mhz_clk' gettind disabled.
When hdmi's runtime_resume() op is called, the call to dss_runtime_get()
correctly enables the DSS clock domain this time. However, the clock
'dss_48mhz_clk' is needed for HDMI's PHY to function correctly. Since it was
disabled previously, the driver fails when it tries to enable HDMI's PHY.
Fix this for now by ensuring that dss_runtime_get() is called before we call
pm_runtime_get_sync() for hdmi's platform device. A correct fix for later would
be to modify the DSS related hwmod's mainclks, and also some changes in how
opt clocks are handled in the DSS driver.
This fixes the issue of HDMI not working when it's the default display. The
issue is not seen if any other display is already enabled as the first display
would have correctly enabled the DSS clockdomain.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
At least on powerpc, it breaks the build if exported functions are
static. Fix some static exported functions introduced with the mlx4
SR-IOV support added in 3.3-rc1.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
A number of new device ids, and a cleanup/fix for some of the option
device ids that shouldn't have been added in the first place.
There's also a few USB 3 fixes for problems that people have reported,
and a usb-storage bugfix to round it out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk9FVQMACgkQMUfUDdst+ym7RgCeNfqK8Oi7U+9rdd2hGGIElxTE
6KgAnipmo5T5Wfls6sh0zPCv8Uh7K6Zb
=SXPd
-----END PGP SIGNATURE-----
Merge tag 'usb-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
USB bugfixes for 3.3-rc4
A number of new device ids, and a cleanup/fix for some of the option
device ids that shouldn't have been added in the first place.
There's also a few USB 3 fixes for problems that people have reported,
and a usb-storage bugfix to round it out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* tag 'usb-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Added Kamstrup VID/PIDs to cp210x serial driver.
USB: Serial: ti_usb_3410_5052: Add Abbot Diabetes Care cable id
usb-storage: fix freezing of the scanning thread
xhci: Fix encoding for HS bulk/control NAK rate.
USB: Set hub depth after USB3 hub reset
USB: Fix handoff when BIOS disables host PCI device.
USB: option: cleanup zte 3g-dongle's pid in option.c
USB: Don't fail USB3 probe on missing legacy PCI IRQ.
xhci: Fix oops caused by more USB2 ports than USB3 ports.
USB: Remove duplicate USB 3.0 hub feature #defines.
In the current kernel implementation, the Logitech Harmony 900 remote
control is matched to the cdc_ether driver through the generic
USB_CDC_SUBCLASS_MDLM entry. However, this device appears to be of the
pseudo-MDLM (Belcarra) type, rather than the standard one. This patch
blacklists the Harmony 900 from the cdc_ether driver and whitelists it for
the pseudo-MDLM driver in zaurus.
Signed-off-by: Scott Talbert <talbert@techie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The intent was to clear out the icount struct here, but we accidentally
clear stack memory instead. It probably will lead to a NULL dereference
right away.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() never returns NULL, so it is wrong to
check if the return value is NULL.
Signed-off-by: RongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel, radeon, exynos fixes.
Intel: fixes a few Ivybridge hangs, along with fixing RC6 on SNB (still
not on, but at least allows for distros to patch it on easily).
radeon: oops reading some files in debugfs that weren't meant to appear,
a fix that touches a lot of files, so looks worse than it is, it fixes
an oops if a GPU reset fails and userspace keeps submitting more data,
along with a minor BIOS fix for newer boards.
exynos: a group of fixes for exynos, they've sent me a few more but
these were all I got through, and its no hw vanilla kernel users see a
lot off yet.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms/atom: dpms bios scratch reg updates
drm/radeon/kms: properly set accel working flag and bailout when false
drm/radeon: Only create additional ring debugfs files on Cayman or newer.
drm/exynos: added postclose to release resource.
drm/exynos: removed exynos_drm_fbdev_recreate function.
drm/exynos: fixed page flip issue.
drm/exynos: added possible_clones setup function.
drm/exynos: removed pageflip_event_list init code when closed.
drm/exynos: changed priority of mixer layers.
drm/exynos: Fix typo in exynos_mixer.c
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
Set the RX FIFO flush watermark lower.
According to Federico and JMicron's reply,
setting it to 16QW would be stable on most platforms.
Otherwise, user might experience packet drop issue.
CC: stable@kernel.org
Reported-by: Federico Quagliata <federico@quagliata.org>
Fixed-by: Federico Quagliata <federico@quagliata.org>
Signed-off-by: Guo-Fu Tseng <cooldavid@cooldavid.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If accel is not working many subsystem such as the ib pool might not be
initialized properly that can lead to segfault inside kernel when cs
ioctl is call with non working acceleration. To avoid this make sure
the accel working flag is false when an error in GPU startup happen and
return EBUSY from cs ioctl if accel is not working.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=46274
Tested with a Cayman card in a Llano system: The additional files are created
and working for the Cayman card but not created for the CPU's built-in GPU.
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/drm-intel:
drm/i915: do not enable RC6p on Sandy Bridge
drm/i915: gen7: Disable the RHWO optimization as it can cause GPU hangs.
drm/i915: gen7: work around a system hang on IVB
drm/i915: gen7: Implement an L3 caching workaround.
drm/i915: gen7: implement rczunit workaround
We moved all our pSeries idle loops to the cpu idle framework
so we really want it to come up by default.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This provides unified readq()/writeq() helper functions for 32-bit
drivers.
For some cases, readq/writeq without atomicity is harmful, and order of
io access has to be specified explicitly. So in this patch, new two
header files which contain non-atomic readq/writeq are added.
- <asm-generic/io-64-nonatomic-lo-hi.h> provides non-atomic readq/
writeq with the order of lower address -> higher address
- <asm-generic/io-64-nonatomic-hi-lo.h> provides non-atomic readq/
writeq with reversed order
This allows us to remove some readq()s that were added drivers when the
default non-atomic ones were removed in commit dbee8a0aff ("x86:
remove 32-bit versions of readq()/writeq()")
The drivers which need readq/writeq but can do with the non-atomic ones
must add the line:
#include <asm-generic/io-64-nonatomic-lo-hi.h> /* or hi-lo.h */
But this will be nop in 64-bit environments, and no other #ifdefs are
required. So I believe that this patch can solve the problem of
1. driver-specific readq/writeq
2. atomicity and order of io access
This patch is tested with building allyesconfig and allmodconfig as
ARCH=x86 and ARCH=i386 on top of tip/master.
Cc: Kashyap Desai <Kashyap.Desai@lsi.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: Matthew Garrett <mjg@redhat.com>
Cc: Jason Uhlenkott <juhlenko@akamai.com>
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: James Bottomley <jbottomley@parallels.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Hitoshi Mitake <h.mitake@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This USB-serial cable with mini stereo jack enumerates as:
Bus 001 Device 004: ID 1a61:3410 Abbott Diabetes Care
It is a TI3410 inside.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1521b) fixes the interaction between usb-storage's
scanning thread and the freezer. The current implementation has a
race: If the device is unplugged shortly after being plugged in and
just as a system sleep begins, the scanning thread may get frozen
before the khubd task. Khubd won't be able to freeze until the
disconnect processing is complete, and the disconnect processing can't
proceed until the scanning thread finishes, so the sleep transition
will fail.
The implementation in the 3.2 kernel suffers from an additional
problem. There the scanning thread calls set_freezable_with_signal(),
and the signals sent by the freezer will mess up the thread's I/O
delays, which are all interruptible.
The solution to both problems is the same: Replace the kernel thread
used for scanning with a delayed-work routine on the system freezable
work queue. Freezable work queues have the nice property that you can
cancel a work item even while the work queue is frozen, and no signals
are needed.
The 3.2 version of this patch solves the problem in Bugzilla #42730.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
CC: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xHCI 0.96 spec says that HS bulk and control endpoint NAK rate must
be encoded as an exponent of two number of microframes. The endpoint
descriptor has the NAK rate encoded in number of microframes. We were
just copying the value from the endpoint descriptor into the endpoint
context interval field, which was not correct. This lead to the VIA
host rejecting the add of a bulk OUT endpoint from any USB 2.0 mass
storage device.
The fix is to use the correct encoding. Refactor the code to convert
number of frames to an exponential number of microframes, and make sure
we convert the number of microframes in HS bulk and control endpoints to
an exponent.
This should be back ported to kernels as old as 2.6.31, that contain the
commit dfa49c4ad1 "USB: xhci - fix math
in xhci_get_endpoint_interval"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Felipe Contreras <felipe.contreras@gmail.com>
Suggested-by: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
The superspeed device attached to a USB 3.0 hub(such as VIA's)
doesn't respond the address device command after resume. The
root cause is the superspeed hub will miss the Hub Depth value
that is used as an offset into the route string to locate the
bits it uses to determine the downstream port number after
reset, and all packets can't be routed to the device attached
to the superspeed hub.
Hub driver sends a Set Hub Depth request to the superspeed hub
except for USB 3.0 root hub when the hub is initialized and
doesn't send the request again after reset due to the resume
process. So moving the code that sends the Set Hub Depth request
to the superspeed hub from hub_configure() to hub_activate()
is to cover those situations include initialization and reset.
The patch should be backported to kernels as old as 2.6.39.
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
On some systems with an Intel Panther Point xHCI host controller, the
BIOS disables the xHCI PCI device during boot, and switches the xHCI
ports over to EHCI. This allows the BIOS to access USB devices without
having xHCI support.
The downside is that the xHCI BIOS handoff mechanism will fail because
memory mapped I/O is not enabled for the disabled PCI device.
Jesse Barnes says this is expected behavior. The PCI core will enable
BARs before quirks run, but it will leave it in an undefined state, and
it may not have memory mapped I/O enabled.
Make the generic USB quirk handler call pci_enable_device() to re-enable
MMIO, and call pci_disable_device() once the host-specific BIOS handoff
is finished. This will balance the ref counts in the PCI core. When
the PCI probe function is called, usb_hcd_pci_probe() will call
pci_enable_device() again.
This should be back ported to kernels as old as 2.6.31. That was the
first kernel with xHCI support, and no one has complained about BIOS
handoffs failing due to memory mapped I/O being disabled on other hosts
(EHCI, UHCI, or OHCI).
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@vger.kernel.org
Initialize PPR register for both channels, and set correct PPR register bits.
Also remove unnecessary variable initializations.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: Merged two patches into one]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Roland Stigge <stigge@antcom.de>
RPM calculation from tachometer value does not depend on PPR.
Also, do not report negative RPM values.
Signed-off-by: Chris D Schimp <silverchris@gmail.com>
[guenter.roeck@ericsson.com: do not report negative RPM values]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: stable@vger.kernel.org # 3.0+
Acked-by: Roland Stigge <stigge@antcom.de>
In port type change flow, need to set the new port types only after
all interfaces have finished the unregister process.
Otherwise, during unregister, one of the interfaces might issue a SET_PORT
command with wrong port types, it can cause bad FW behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under the spinlock we call request_irq(), which allocates memory with GFP_KERNEL,
This causes the following trace when DEBUG_SPINLOCK is enabled, it can cause
the following trace:
BUG: spinlock wrong CPU on CPU#2, ethtool/2595
lock: ffff8801f9cbc2b0, .magic: dead4ead, .owner: ethtool/2595, .owner_cpu: 0
Pid: 2595, comm: ethtool Not tainted 3.0.18 #2
Call Trace:
spin_bug+0xa2/0xf0
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
mlx4_assign_eq+0x12b/0x190 [mlx4_core]
mlx4_en_activate_cq+0x252/0x2d0 [mlx4_en]
? mlx4_en_activate_rx_rings+0x227/0x370 [mlx4_en]
mlx4_en_start_port+0x189/0xb90 [mlx4_en]
mlx4_en_set_ringparam+0x29a/0x340 [mlx4_en]
dev_ethtool+0x816/0xb10
? dev_get_by_name_rcu+0xa4/0xe0
dev_ioctl+0x2b5/0x470
handle_mm_fault+0x1cd/0x2d0
sock_do_ioctl+0x5d/0x70
sock_ioctl+0x79/0x2f0
do_vfs_ioctl+0x8c/0x340
sys_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
Replacing with mutex, which is enough in this case.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 16adf5d079 I removed an over-broad
alias that caused zaurus.ko to bind to unrelated devices.
I had a report that at least one valid case no longer auto-loads because of this.
This patch adds an ID for that case.
Reported-by: Raphael Wimmer <raphael.wimmer@ur.de>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to remove a key, we always send key
flags just setting the key type, not including
the multicast flag and the key ID. As a result,
whenever any key was removed, the unicast key 0
would be removed, causing a complete connection
loss after the second rekey (the first doesn't
cause a key removal). Fix the key removal code
to include the key ID and multicast flag, thus
removing the correct key.
Cc: stable@vger.kernel.org
Reported-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Tested-by: Alexander Schnaidt <alex.schnaidt@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'rt2x00lib_probe_dev' function tries to
allocate the workqueue. If the allocation
fails, 'rt2x00_lib_remove_dev' is called on
the error path. Because 'rt2x00dev->workqueue'
is NULL in this case, the 'destroy_workqueue'
call will cause a NULL pointer dereference.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Duplicate the data for iniAddac early on, to avoid having to do redundant
memcpy calls later. While we're at it, make AR5416 < v2.2 use the same
codepath. Fixes a reported crash on x86.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Magnus Määttä <magnus.maatta@logica.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'fixes' of git://github.com/hzhuang1/linux:
pxa/hx4700: add platform device and I2C info for AK4641 codec
arch/arm/mach-pxa/: included linux/gpio.h twice
arch/arm/mach-mmp/: some files include some headers twice
ARM: pxa: fix error handling in pxa2xx_drv_pcmcia_probe
ARM: pxa: fix including linux/gpio.h twice
ARM: pxa: fix mixed declarations and code in sharpsl_pm
ARM: pxa: fix wrong parsing gpio event on spitz
We were not freeing the irq properly in the error path in
the AB8500 driver.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The jack detection on WM1811 is often required during system suspend, add
it as another check when deciding if we should suspend.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
BF can be disabled in some cases, the capability field, bf_reg_size is set
to zero in this case. Don't map the BF area in this case, it would cause
failures. In addition, leaving the BF area unmapped
also alerts the ETH driver to not use BF.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
[S390] correct ktime to tod clock comparator conversion
[S390] 3215 deadlock with tty_wakeup
[S390] incorrect PageTables counter for kvm page tables
[S390] idle: avoid RCU usage in extended quiescent state
irq_base of the tps65910 irq platform data should be
initialized with the board provided irq_base data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Remove "wm8350->irq_base = pdata->irq_base" to avoid
null pointer exception and wm8350->irq_base got from
irq_alloc_descs().
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In the case of hotplug enabled devices (PCMCIA/PCIeC) the removal of the
hardware can cause an infinite loop in the common sja1000 isr.
Use the already retrieved status register to indicate a possible hardware
removal and double check by reading the mode register in sja1000_is_absent.
Cc: stable@kernel.org [3.2+]
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
WARNING: drivers/net/ethernet/broadcom/built-in.o(.init.text+0x5d): Section mismatch in reference from the function b44_init() to the function .exit.text:b44_pci_exit()
module exits with b44_cleanup()
Signed-off-by: Nikola Pajkovsky <n.pajkovsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The calls to pci_iounmap are in the wrong order, as compared to the
associated calls to pci_iomap.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,x;
statement S,S1;
int ret;
@@
e = pci_iomap(x,...)
... when != pci_iounmap(x,e)
if (<+...e...+>) S
... when any
when != pci_iounmap(x,e)
*if (...)
{ ... when != pci_iounmap(x,e)
return ...; }
... when any
pci_iounmap(x,e);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->irq is unsigned, so it's never less than zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was recently shown that vmxnet3 devices on transmit, will drop very small udp
frames consistently. This is due to a regression introduced by commit
39d4a96fd7. This commit attempts to introduce an
optimization to the tx path, indicating that the underlying hardware behaves
optimally when at least 54 bytes of header data are available for direct access.
This causes problems however, if the entire frame is less than 54 bytes long.
The subsequent pskb_may_pull in vmxnet3_parse_and_copy_hdr fails, causing an
error return code, which leads to vmxnet3_tq_xmit dropping the frame.
Fix it by placing a cap on the copy length. For frames longer than 54 bytes, we
do the pull as we normally would. If the frame is shorter than that, copy the
whole frame, but no more. This ensures that we still get the optimization for
qualifying frames, but don't do any damange for frames that are too short.
Also, since I'm unable to do this, it wuold be great if vmware could follow up
this patch with some additional code commentary as to why 54 bytes is an optimal
pull length for a virtual NIC driver. The comment that introduced this was
vague on that. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Max Matveev <mmatveev@redhat.com>
CC: Max Matveev <mmatveev@redhat.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Shreyas Bhatewara <sbhatewara@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver attempts to use two TX rings but lacks proper support :
1) IRQ handler only takes care of TX completion on first TX ring
2) the stop/start logic uses the legacy functions (for non multiqueue
drivers)
This means all packets witk skb mark set to 1 are sent through high
queue but are never cleaned and queue eventualy fills and block the
device, triggering the infamous "NETDEV WATCHDOG" message.
Lets use a single TX ring to fix the problem, this driver is not a real
multiqueue one yet.
Minimal fix for stable kernels.
Reported-by: Thomas Meyer <thomas@m3y3r.de>
Tested-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=QYVn
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
These are the bug fixes that have accumulated since 3.3-rc3 in arm-soc.
The majority of them are regression fixes for stuff that broke during
the merge 3.3 window.
The notable ones are:
* The at91 ata drivers both broke because of an earlier cleanup patch that
some other patches were based on. Jean-Christophe decided to remove
the legacy at91_ide driver and fix the new-style at91-pata driver while
keeping the cleanup patch. I almost rejected the patches for being too
late and too big but in the end decided to accept them because they
fix a regression.
* A patch fixing build breakage from the sysdev-to-device conversion
colliding with other changes touches a number of mach-s3c files.
* b0654037 "ARM: orion: Fix Orion5x GPIO regression from MPP cleanup"
is a mechanical change that unfortunately touches a lot of lines
that should up in the diffstat.
* tag 'fixes-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: at91: drop ide driver in favor of the pata one
pata/at91: use newly introduced SMC accessors
ARM: at91: add accessor to manage SMC
ARM: at91:rtc/rtc-at91sam9: ioremap register bank
ARM: at91: USB AT91 gadget registration for module
ep93xx: fix build of vision_ep93xx.c
ARM: OMAP2xxx: PM: fix OMAP2xxx-specific UART idle bug in v3.3
ARM: orion: Fix USB phy for orion5x.
ARM: orion: Fix Orion5x GPIO regression from MPP cleanup
ARM: EXYNOS: Add cpu-offset property in gic device tree node
ARM: EXYNOS: Bring exynos4-dt up to date
ARM: OMAP3: cm-t35: fix section mismatch warning
ARM: OMAP2: Fix the OMAP2 only build break seen with 2011+ ARM tool-chains
ARM: tegra: paz00: fix wrong UART port on mini-pcie plug
ARM: tegra: paz00: fix wrong SD1 power gpio
i2c: tegra: Add devexit_p() for remove
ARM: EXYNOS: Correct M-5MOLS sensor clock frequency on Universal C210 board
ARM: EXYNOS: Correct framebuffer window size on Nuri board
ARM: SAMSUNG: Fix missing api-change from subsys_interface change
ARM: EXYNOS: Fix "warning: initialization from incompatible pointer type"
...
1) VETH_INFO_PEER netlink attribute needs to have it's size validated,
from Thomas Graf.
2) 'poll' module option of bnx2x driver crashes the machine, just remove
it. From Michal Schmidt.
3) ks8851_mll driver reads the irq number from two places, but only
initializes one of them, oops. Use only one location and fix this
problem, from Jan Weitzel.
4) Fix buffer overrun and unicast sterring bugs in mellanox mlx4 driver,
from Eugenia Emantayev.
5) Swapped kcalloc() args in RxRPC and mlx4, from Axel Lin.
6) PHY MDIO device name regression fixes from Florian Fainelli.
7) If the wake event IRQ line is different from the netdevice one, we
have to properly route it to the stmmac interrupt handler. From
Francesco Virlinzi.
8) Fix rwlock lock initialization ordering bug in mac80211, from
Mohammed Shafi Shajakhan.
9) TCP lost_cnt can get out of sync, and in fact go negative, in certain
circumstances. Fix the way we specify what sequence range to operate
on in tcp_sacktag_one() to fix this bug. From Neal Cardwell.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (27 commits)
net/ethernet: ks8851_mll fix irq handling
veth: Enforce minimum size of VETH_INFO_PEER
stmmac: update the driver version to Feb 2012 (v2)
stmmac: move hw init in the probe (v2)
stmmac: request_irq when use an ext wake irq line (v2)
stmmac: do not discard frame on dribbling bit assert
ipheth: Add iPhone 4S
mlx4: add unicast steering entries to resource_tracker
mlx4: fix QP tree trashing
mlx4: fix buffer overrun
3c59x: shorten timer period for slave devices
netpoll: netpoll_poll_dev() should access dev->flags
RxRPC: Fix kcalloc parameters swapped
bnx2x: remove the 'poll' module option
tcp: fix tcp_shifted_skb() adjustment of lost_cnt_hint for FACK
ks8851: Fix NOHZ local_softirq_pending 08 warning
bnx2x: fix bnx2x_storm_stats_update() on big endian
ixp4xx-eth: fix PHY name to match MDIO bus name
octeon: fix PHY name to match MDIO bus name
fec: fix PHY name to match fixed MDIO bus name
...
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pU4C
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Fixes a bootstrapping issue for some registers when a less commonly used
method for register cache initialisation is used. Only affects a fairly
small proportion of users that both don't use explicit register defaults
and do use the cache.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Fix cache defaults initialization from raw cache defaults
Here are a few more fixes for powerpc. Some are regressions, the rest
is simple/obvious/nasty enough that I deemed it good to go now.
Here's also step one of deprecating legacy iSeries support: we are
removing it from the main defconfig.
Nobody seems to be using it anymore and the code is nasty to maintain,
(involves horrible hacks in various low level areas of the kernel) so we
plan to actually rip it out at some point. For now let's just avoid
building it by default. Stephen will proceed to do the actual removal
later (probably 3.4 or 3.5).
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc/perf: power_pmu_start restores incorrect values, breaking frequency events
powerpc/adb: Use set_current_state()
powerpc: Disable interrupts early in Program Check
powerpc: Remove legacy iSeries from ppc64_defconfig
powerpc/fsl/pci: Fix PCIe fixup regression
powerpc: Fix kernel log of oops/panic instruction dump
One regression fix for SR-IOV on PPC and a couple of misc fixes from
Yinghai.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Fix pci cardbus removal
PCI: set pci sriov page size before reading SRIOV BAR
PCI: workaround hard-wired bus number V2
3 radeon fixes, I have some exynos fixes to push later but I'll queue
them separately once I've looked them over a bit.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: fix MSI re-arm on rv370+
drm/radeon/kms/atom: bios scratch reg handling updates
drm/radeon/kms: drop lock in return path of radeon_fence_count_emitted.
This patch (as1520) fixes a bug in the SCSI layer's power management
implementation.
LUN scanning can be carried out asynchronously in do_scan_async(), and
sd uses an asynchronous thread for the time-consuming parts of disk
probing in sd_probe_async(). Currently nothing coordinates these
async threads with system sleep transitions; they can and do attempt
to continue scanning/probing SCSI devices even after the host adapter
has been suspended. As one might expect, the outcome is not ideal.
This is what the "prepare" stage of system suspend was created for.
After the prepare callback has been called for a host, target, or
device, drivers are not allowed to register any children underneath
them. Currently the SCSI prepare callback is not implemented; this
patch rectifies that omission.
For SCSI hosts, the prepare routine calls scsi_complete_async_scans()
to wait until async scanning is finished. It might be slightly more
efficient to wait only until the host in question has been scanned,
but there's currently no way to do that. Besides, during a sleep
transition we will ultimately have to wait until all the host scanning
has finished anyway.
For SCSI devices, the prepare routine calls async_synchronize_full()
to wait until sd probing is finished. The routine does nothing for
SCSI targets, because asynchronous target scanning is done only as
part of host scanning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In do_scan_async(), calling scsi_autopm_put_host(shost) may reference
freed shost, and cause Posison overwitten warning.
Yes, this case can happen, for example, an USB is disconnected just
when do_scan_async() thread starts to run, then scsi_host_put() called
in scsi_finish_async_scan() will lead to shost be freed(because the
refcount of shost->shost_gendev decreases to 1 after USB disconnects),
at this point, if references shost again, system will show following
warning msg.
To make scsi_autopm_put_host(shost) always reference a valid shost,
put it just before scsi_host_put() in function
scsi_finish_async_scan().
[ 299.281565] =============================================================================
[ 299.281634] BUG kmalloc-4096 (Tainted: G I ): Poison overwritten
[ 299.281682] -----------------------------------------------------------------------------
[ 299.281684]
[ 299.281752] INFO: 0xffff880056c305d0-0xffff880056c305d0. First byte
0x6a instead of 0x6b
[ 299.281816] INFO: Allocated in scsi_host_alloc+0x4a/0x490 age=1688
cpu=1 pid=2004
[ 299.281870] __slab_alloc+0x617/0x6c1
[ 299.281901] __kmalloc+0x28c/0x2e0
[ 299.281931] scsi_host_alloc+0x4a/0x490
[ 299.281966] usb_stor_probe1+0x5b/0xc40 [usb_storage]
[ 299.282010] storage_probe+0xa4/0xe0 [usb_storage]
[ 299.282062] usb_probe_interface+0x172/0x330 [usbcore]
[ 299.282105] driver_probe_device+0x257/0x3b0
[ 299.282138] __driver_attach+0x103/0x110
[ 299.282171] bus_for_each_dev+0x8e/0xe0
[ 299.282201] driver_attach+0x26/0x30
[ 299.282230] bus_add_driver+0x1c4/0x430
[ 299.282260] driver_register+0xb6/0x230
[ 299.282298] usb_register_driver+0xe5/0x270 [usbcore]
[ 299.282337] 0xffffffffa04ab03d
[ 299.282364] do_one_initcall+0x47/0x230
[ 299.282396] sys_init_module+0xa0f/0x1fe0
[ 299.282429] INFO: Freed in scsi_host_dev_release+0x18a/0x1d0 age=85
cpu=0 pid=2008
[ 299.282482] __slab_free+0x3c/0x2a1
[ 299.282510] kfree+0x296/0x310
[ 299.282536] scsi_host_dev_release+0x18a/0x1d0
[ 299.282574] device_release+0x74/0x100
[ 299.282606] kobject_release+0xc7/0x2a0
[ 299.282637] kobject_put+0x54/0xa0
[ 299.282668] put_device+0x27/0x40
[ 299.282694] scsi_host_put+0x1d/0x30
[ 299.282723] do_scan_async+0x1fc/0x2b0
[ 299.282753] kthread+0xdf/0xf0
[ 299.282782] kernel_thread_helper+0x4/0x10
[ 299.282817] INFO: Slab 0xffffea00015b0c00 objects=7 used=7 fp=0x
(null) flags=0x100000000004080
[ 299.282882] INFO: Object 0xffff880056c30000 @offset=0 fp=0x (null)
[ 299.282884]
...
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: stable@kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With IOs running and PegHalt testing the system reboots when memory reset is
performed during device initialization.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Complete the mailbox command timed out before initiating another abort cycle
to recover so that mailbox commands issued during next reset cycle don't fail
due to pending mailbox access timeout.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove the check for a NULL fcport so that the host reset will run
unconditionally to unwedge any commands before the device is offlined and to
prevent a quick runthrough of the SCSI error handling.
Signed-off-by: Michael Christie <mchristi@redhat.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
ISP2200 adapters only have 24 mailbox registers so read only that many.
Reported-by: Olatunji Ruwase <oor@cs.cmu.edu>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This can cause instability in mailbox command state machine handling.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Not clearing the options flags in mbx1 could lead the firmware
into interpreting old data in mbx1 through mbx8. This could
lead to inadvertent DMA read/write operations to stale memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Many locations within the driver would use an inconsistent set of
checks to determine ISP-reset state. Consolidate the checks into
this inline-helper.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
NULL orom ptr passed in for verification which caused page fault.
We will set a default version when we don't have orom struct.
Reported-by: Dan Melnic <dan@seamicro.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In some scenarios, an EEH error can take a long time to be detected, since the
driver issues an MMIO read only after a device reset command times out and we
try to reset the adapter. This patch adds some code in ipr_cancel_op() to read
a hardware register so we detect the error earlier in case the op is being
aborted because of a timeout caused by a frozen adapter slot.
Another problem in such scenarios is that in __ipr_eh_host_reset() we change the
dump state flag from WAIT_FOR_DUMP to GET_DUMP, and the flag is later changed
from GET_DUMP to READ_DUMP in ipr_reset_restore_cfg_space(). However, if when
__ipr_eh_host_reset() is called by the SCSI error handling the function
ipr_reset_restore_cfg_space() has already been called by the PCI EEH code, we
end up with the flag in an inconsistent state. This patch also prevents this
problem.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The 3215 driver calls tty_wakeup from irq context while holding the
device spinlock. If printk is called by any function on the callchain
starting from tty_wakeup the system deadlocks on the device spinlock.
Using a tasklet to call tty_wakup solves the problem.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
this function ins't needed anymore.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
with vblank_refcount = 1, there was the case that drm_vblank_put
is called by specific page flip function so this patch fixes the
issue.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
basically, all crtcs are possible to clone each other.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
if one process is terminated by ctrl-c while two processes are
using pageflip feature then for last pageflip event,
user can't get poll from kernel side so this patch fixes the problem.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyoungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If pxa2xx_drv_pcmcia_add_one fails, it will go to err1 error path.
Add a missing clk_put in the error path.
Checking the ret value after the for loop is redundant, it is always false.
Thus remove the redundant checking.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
With base on latest findings, RC6p seems to be respondible for RC6-related
issues on Sandy Bridge platform. To work-around those issues, the previous
solution was to completely disable RC6 on Sandy Bridge for the past few
releases, even if plain RC6 was not giving any issues.
What this patch does is preventing RC6p from being enabled on Sandy Bridge
even if users enable RC6 via a kernel parameter. So it won't change the
defaults in any way, but will ensure that if users do enable RC6 manually
it won't break their machines by enabling this extra state.
Proper fix for this (enabling specific RC6 states according to the GPU
generation) were proposed for the -next kernel, but we are too late in the
release process now to pick such changes.
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There a two different irq variables ks->irq and netdev->irq.
Only ks->irq is set on probe, so disabling irq in ks_start_xmit fails.
This patches remove ks->irq from private data and use only netdev->irq.
Tested on a kernel 3.0 based OMAP4430 SMP Board
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
VETH_INFO_PEER carries struct ifinfomsg plus optional IFLA
attributes. A minimal size of sizeof(struct ifinfomsg) must be
enforced or we may risk accessing that struct beyond the limits
of the netlink message.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: http://bugs.launchpad.net/bugs/900802
Cc: stable@vger.kernel.org 3.2+
Signed-off-by: Till Kamppeter <till.kamppeter@gmail.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add unicast steering entries to resource tracker.
Do qp_detach also for these entries when VF doesn't shut down gracefully.
Otherwise there is leakage of these resources, since they are not tracked.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding new unicast steer entry, before moving qp to state ready,
actually before calling mlx4_RST2INIT_QP_wrapper(), there were added
a lot of entries with local_qpn=0 into radix tree.
This fact impacted the get_res() function and proper functioning
of resource tracker in addition to adding trash entries into radix tree.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@melllanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When passing MLX4_UC_STEER=1 it was translated to value 2
after mlx4_QP_ATTACH_wrapper. Therefore in new_steering_entry()
unicast steer entries were added to index 2 of array of size 2.
Fixing this bug by shift right to one position.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver maintains different flags for WEP, WPA, WPA2 security modes.
Appropriate flag is set using security information provided in
connect request. mwifiex_is_network_compatible() routine uses them
to check if driver's setting is compatible with AP. Association is
aborted if the routine fails.
For some corner cases, it is observed that association is failed
even for valid security information based on association history.
This patch fixes the problem by clearing previous security setting
during each association.
We should set WEP key provided in connect request as default tx key.
This missing change is also added here.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently registers with a value of 0 are ignored when initializing the register
defaults from raw defaults. This worked in the past, because registers without a
explicit default were assumed to have a default value of 0. This was changed in
commit b03622a8 ("regmap: Ensure rbtree syncs registers set to zero properly").
As a result registers, which have a raw default value of 0 are now assumed to
have no default. This again can result in unnecessary writes when syncing the
cache. It will also result in unnecessary reads for e.g. the first update
operation. In the case where readback is not possible this will even let the
update operation fail, if the register has not been written to before.
So this patch removes the check. Instead it adds a check to ignore raw defaults
for registers which are volatile, since those registers are not cached.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Correctly sets the max/min/default values for the hdpvr picture
controls. The reason the current values didn't cause a problem until now
is because any firmware <= 0.15 didn't support them. The latest firmware
releases properly support picture controls and the values in the patch
are derived from the windows driver using SniffUSB2.0.
Thanks to Devin Heitmueller for helping me.
Signed-off-by: Taylor Ralph <tralph@mythtv.org>
Thanks-to: Devin Heitmueller <dheitmueller@kernellabs.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
From: Randy Dunlap <rdunlap@xenotime.net>
Fix wl128x Kconfig to depend on GPIOLIB since TI_ST also
depends on GPIOLIB.
(.text+0xe6d60): undefined reference to `st_register'
(.text+0xe7016): undefined reference to `st_unregister'
(.text+0xe70ce): undefined reference to `st_unregister'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Manjunatha Halli <manjunatha_halli@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[ 2096.384084] btusb_send_frame:684: hci0
[ 2096.384087] usb 3-1: BOGUS urb flags, 2 --> 0
[ 2096.384091] Bluetooth: hci0 urb ffff8801b61d3a80 submission failed (22)
According the documentation in usb_submit_urb() URB_ISO_ASAP
flag is only allowed for endpoints of type USB_ENDPOINT_XFER_ISOC.
This reverts commit b8aabfc922.
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
with vblank_refcount = 1, there was the case that drm_vblank_put
is called by specific page flip function so this patch fixes the
issue.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
basically, all crtcs are possible to clone each other.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
if one process is terminated by ctrl-c while two processes are
using pageflip feature then for last pageflip event,
user can't get poll from kernel side so this patch fixes the problem.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyoungmin Park <kyungmin.park@samsung.com>
but commonly built configs which for some reason manage to survive for
an awfully long time in -next without any reports.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=fFEV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
One small bug fix from Axel plus a fix for a build failure in unrealistic
but commonly built configs which for some reason manage to survive for
an awfully long time in -next without any reports.
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Fix getting voltage in max8649_enable_time()
regulator: Fix mc13xxx regulator modular build (again)
* The most visible fix here is against a regression introduced in 3.3-rc1
that ran cards in Ultra High Speed mode even when they failed to initialize
in that mode, leading to lower-speed cards failing to mount.
* A lockdep warning introduced in 3.3-rc1 is fixed.
* Various other small driver fixes, most notably for a NULL dereference
when using highmem with dw_mmc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XEG7
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
MMC fixes for 3.3-rc4:
* The most visible fix here is against a regression introduced in 3.3-rc1
that ran cards in Ultra High Speed mode even when they failed to initialize
in that mode, leading to lower-speed cards failing to mount.
* A lockdep warning introduced in 3.3-rc1 is fixed.
* Various other small driver fixes, most notably for a NULL dereference
when using highmem with dw_mmc.
* tag 'mmc-fixes-for-3.3-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: dw_mmc: Fix PIO mode with support of highmem
mmc: atmel-mci: save and restore sdioirq when soft reset is performed
mmc: block: Init ro_lock sysfs attr to fix lockdep warnings
mmc: sh_mmcif: fix late delayed work initialisation
mmc: tmio_mmc: fix card eject during IO with DMA
mmc: core: Fix comparison issue in mmc_compare_ext_csds
mmc: core: Fix PowerOff Notify suspend/resume
mmc: sdhci-pci: set Medfield SDIO as non-removable
mmc: core: add the capability for broken voltage
mmc: core: Fix low speed mmc card detection failure
mmc: esdhc: set the timeout to the max value
mmc: esdhc: add PIO mode support
mmc: core: Ensure clocks are always enabled before host interaction
mmc: of_mmc_spi: fix little endian support
mmc: core: UHS sdio card that fails should not exceed 50MHz
mmc: esdhc: fix errors when booting kernel on Freescale eSDHC version 2.3
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJPOeReAAoJEFjIrFwIi8fJn9QIANP48kzrGg0uO4bjSf2h/z7G
pp3ISdtVLk7pwMov2POBqskoXSq8E0yQAfNN8se183wqNXo3Dm4rU1DIG7HQFBk9
sdcyfHI8x7pat9JClRhGxpQ23Ig9f1iWkShweCcZCO782vfxZyNd65i6t87X7uLq
7SPtG1XH2RixTX7tHtKKBqdzZ0OMXOEkJ33dgCmyrn+wzohbKrFj5mg+NdOgmzEo
VgsHPVtuq7orDROe+F9d91eAg0TILQ13th8xfWZ59lQATXu/zAlaueYt87tpy1pb
oVQvumsn8Xev+7hct9My9Tw45D4m8YOSFLG2HcekkW2WtNmGhTTbIyMh9PsLugk=
=NDYK
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Two fixes for VCPU offlining; One to fix the string format exposed
by the xen-pci[front|back] to conform to the one used in majority of
PCI drivers; Two fixes to make the code more resilient to invalid
configurations.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
* tag 'stable/for-linus-fixes-3.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus_dev: add missing error check to watch handling
xen/pci[front|back]: Use %d instead of %1x for displaying PCI devfn.
xen pvhvm: do not remap pirqs onto evtchns if !xen_have_vector_callback
xen/smp: Fix CPU online/offline bug triggering a BUG: scheduling while atomic.
xen/bootup: During bootup suppress XENBUS: Unable to read cpu state
1. Remove all old mass-storage ids's pid:
0x0026,0x0053,0x0098,0x0099,0x0149,0x0150,0x0160;
2. As the pid from 0x1401 to 0x1510 which have not surely assigned to
use for serial-port or mass-storage port,so i think it should be
removed now, and will re-add after it have assigned in future;
3. sort the pid to WCDMA and CDMA.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jean Delvare reported bonding on top of 3c59x adapters was not detecting
network cable removal fast enough.
3c59x indeed uses a 60 seconds timer to check link status if carrier is
on, and 5 seconds if carrier is off.
This patch reduces timer period to 5 seconds if device is a bonding
slave.
Reported-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'poll' was a debugging option, but turning it on these days leads to
kernel panic. Remove it.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel has a PCI USB xhci host controller on a new platform. It doesn't
have a line IRQ definition in BIOS. The Linux driver refuses to
initialize this controller, but Windows works well because it only depends
on MSI.
Actually, Linux also can work for MSI. This patch avoids the line IRQ
checking for USB3 HCDs in usb core PCI probe. It allows the xHCI driver
to try to enable MSI or MSI-X first. It will fail the probe if MSI
enabling failed and there's no legacy PCI IRQ.
This patch should be backported to kernels as old as 2.6.32.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
status has to be set to STREAMING before the streaming worker is
queued. hdpvr_transmit_buffers() will exit immediately otherwise.
Reported-by: Joerg Desch <vvd.joede@googlemail.com>
CC: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Add missing DFP6 connection state handling
- crtc routing bits not used on DCE4+
Noticed by sylware on phoronix.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Silly bad return path.
Reported-and-Tested-by: Mikko Vinni
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
CC: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes a software reset is needed. Then some registers are saved and
restored but the interrupt mask register is missing. It causes issues
with sdio devices whose interrupts are masked after reset.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If the driver is loaded with a card in the slot, mmc_add_host() will
schedule an immediate card-detection work, which will start IO and wait
for command completion. Usually the kernel first returns to the sh_mmcif
probe function, lets it finish and only then schedules the rescan work.
But sometimes, expecially under heavy system load, the work will be
scheduled immediately before returning to the probe method. In this case
it is important for the driver to be fully prepared for IO. For sh_mmcif
this means, that also the timeout work has to be initialised before
calling mmc_add_host(). It is also better to prepare interrupts
beforehand. Besides, since mmc_add_host() does card-detection itself,
there is no need to do it again immediately afterwards.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
When DMA is in use and the card is ejected during IO, DMA transfers have to
be terminated, otherwise the dmaengine driver fails to operate properly,
when the card is re-inserted.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Found this issue during code review. Actually, there are two issues which
both compensate together in lucky case. In unlucky case the bus width
probing might not work as expected.
Signed-off-by: Jurgen Heeks <jurgen.heeks@nokia.com>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modified the mmc_poweroff to resume before sending the poweroff
notification command. In sleep mode only AWAKE and RESET commands are
allowed, so before sending the poweroff notification command resume from
sleep mode and then send the notification command.
PowerOff Notify is tested on a Synopsis Designware Host Controller
(eMMC 4.5). The suspend to RAM and resume works fine.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Tested-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Saugata Das <saugata.das@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Set Medfield SDIO as non-removable to avoid un-necessary
card detect activity.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
There is an understood mismatch between the voltage the host controller is
set to and the voltage supplied to the card by a fixed voltage regulator.
Teaching the driver to accept the mismatch is overly complicated. Instead
just accept the regulator's voltage.
This patch adds MMC_CAP2_BROKEN_VOLTAGE.
If the voltage didn't satisfy between min_uV and max_uV, try to change
the voltage in core.c. When changing the voltage, maybe use
regulator_set_voltage().
In regulator_set_voltage(), check the below condition.
/* sanity check */
if (!rdev->desc->ops->set_voltage &&
!rdev->desc->ops->set_voltage_sel) {
ret = -EINVAL;
goto out;
}
If some board should use the fixed-regulator, always return -EINVAL.
Then, eMMC didn't initialize always.
So if use a fixed-regulator, we need to add the MMC_CAP2_BROKEN_VOLTAGE.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes the failure of low speed mmc card detection.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When accessing the card on some FSL platform boards (e.g p2020, p1010,
mpc8536), the following error is reported with the timeout value calculated:
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
mmc0: Got data interrupt 0x00000020 even though no data operation was
in progress.
So we skip the calculation of timeout and use the max value to fix it.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
For some FSL ESDHC controllers (e.g. P2020E, Rev1.0), the SDHC can not
work on DMA mode because of the hardware bug, so we set a broken dma flag
and use PIO mode.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Gao Guanhua <B22826@freescale.com>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ensure clocks are always enabled before any interaction with the
host controller driver. This makes sure that there is no race
between host execution and the core layer turning off clocks
in different context with clock gating framework.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Per Forlin <per.forlin@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Tomi Valkeinen