Use the registration/notification framework supported by the generic
failover infrastructure.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCTP sockets originated in a VRF can improve their performance if CRC32c
computation is delegated to underlying devices: update device features,
setting NETIF_F_SCTP_CRC. Iterating the following command in the topology
proposed with [1],
# ip vrf exec vrf-h2 netperf -H 192.0.2.1 -t SCTP_STREAM -- -m 10K
the measured throughput in Mbit/s improved from 2395 ± 1% to 2720 ± 1%.
[1] https://www.spinics.net/lists/netdev/msg486007.html
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers, such as DWC EQOS on Tegra, need to perform operations that
can sleep under this lock (clk_set_rate() in tegra_eqos_fix_speed()) for
proper operation. Since there is no need for this lock to be a spinlock,
convert it to a mutex instead.
Fixes: e6ea2d16fc ("net: stmmac: dwc-qos: Add Tegra186 support")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx-timeout mostly happens due to some issue in the device. In such cases,
debug dump would be helpful for identifying the cause of the issue.
This patch adds support to spill debug data during the Tx timeout. Here
bnx2x_panic_dump() API is used instead of bnx2x_panic(), since we still
want to allow the Tx-timeout recovery a chance to succeed.
Changes from previous version:
-------------------------------
v2: Fixed a coding error.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limiting the dma mask to avoid PCI (pre-PCIe) DAC cycles while paying
the huge overhead of an IOMMU is rather pointless, and this seriously
gets in the way of dma mapping work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Move all RQ, SQ and channel counters from the channel objects into the
priv structure. With this change, counters will not be reset upon
channel configuration changes.
Channel's statistics for SQs which are associated with TCs higher than
zero will be presented in ethtool -S, only for SQs which were opened at
least once since the module was loaded (regardless of their open/close
current status). This is done in order to decrease the total amount of
statistics presented and calculated for the common out of box use (no
QoS).
mlx5e_channel_stats is a compound of CH,RQ,SQs stats in order to
create locality for the NAPI when handling TX and RX of the same
channel.
Align the new statistics struct per ring to avoid several channels
update to the same cache line at the same time.
Packet rate was tested, no degradation sensed.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Qing Huang <qing.huang@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- PCI Express bandwidth of %dGT/s available
- (Speed:%s, Width: x%d, Encoding Loss:%s)
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
or, if the device is capable of better performance than is available in the
current slot:
- This is not sufficient for optimal performance of this card.
- For optimal performance, at least %dGT/s of bandwidth is required.
- A slot with more lanes and/or higher speed is suggested.
+ %u.%03u Gb/s available PCIe bandwidth, limited by %s x%d link at %s (capable of %u.%03u Gb/s with %s x%d link)
Note that the driver previously used dev_warn() to suggest using a
different slot, but pcie_print_link_status() uses dev_info() because if the
platform has no faster slot available, the user can't do anything about the
warning and may not want to be bothered with it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- PCIe link speed is %s, device supports %s
- PCIe link width is x%d, device supports x%d
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
or, if the device is capable of better performance than is available in the
current slot:
- A slot with more lanes and/or higher speed is suggested for optimal performance.
+ %u.%03u Gb/s available PCIe bandwidth, limited by %s x%d link at %s (capable of %u.%03u Gb/s with %s x%d link)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- PCIe: Speed %s Width x%d
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously the driver used pcie_get_minimum_link() to warn when the NIC
is in a slot that can't supply as much bandwidth as the NIC could use.
pcie_get_minimum_link() can be misleading because it finds the slowest link
and the narrowest link (which may be different links) without considering
the total bandwidth of each link. For a path with a 16 GT/s x1 link and a
2.5 GT/s x16 link, it returns 2.5 GT/s x1, which corresponds to 250 MB/s of
bandwidth, not the true available bandwidth of about 1969 MB/s for a
16 GT/s x1 link.
Use pcie_print_link_status() to report PCIe link speed and possible
limitations instead of implementing this in the driver itself. This finds
the slowest link in the path to the device by computing the total bandwidth
of each link and compares that with the capabilities of the device.
The dmesg change is:
- %s (%c%d) PCI-E x%d %s found at mem %lx, IRQ %d, node addr %pM
+ %s (%c%d) PCI-E found at mem %lx, IRQ %d, node addr %pM
+ %u.%03u Gb/s available PCIe bandwidth (%s x%d link)
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce a new read/write lock that will protect statistics gathering from
netdev channels configuration changes.
e.g. when channels are being replaced (increase/decrease number of rings)
prevent statistic gathering (ndo_get_stats64) to read the statistics of
in-active channels (channels that are being closed).
Plus update channels software statistics on the fly when calling
ndo_get_stats64, and remove it from stats periodic work.
Fixes: 9218b44dcc ("net/mlx5e: Statistics handling refactoring")
Signed-off-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PHY link down events counter belongs to phy_counters group.
although it has special handling, it doesn't mean it can't be there.
Move it to phy_counters_grp handler.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Complete the transition of all WQ types to use fragmented
order-0 coherent memory instead of high-order allocations.
CQ-WQ already uses order-0.
Here we do the same for cyclic and linked-list WQs.
This allows the driver to load cleanly on systems with a highly
fragmented coherent memory.
Performance tests:
ConnectX-5 100Gbps, CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet rate of 64B packets, single transmit ring, size 8K.
No degradation is sensed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If CONFIG_MLX5_CORE_IPOIB is not set, compile-out the
IPOIB related headers.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We fill SQ edge with NOPs to avoid WQEs wrap.
Here, instead of doing that in advance for the maximum possible
WQE size, we do it on-demand using the actual WQE size.
We re-order some parts in mlx5e_sq_xmit to finish the calculation
of WQE size (ds_cnt) before doing any writes to the WQE buffer.
When SQ work queue is fragmented (introduced in an downstream patch),
dealing with WQE wraps becomes more frequent. This change would drastically
reduce the overhead in this case.
Performance tests:
ConnectX-5 100Gbps, CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet rate of 64B packets, single transmit ring, size 8K.
Before: 14.9 Mpps
After: 15.8 Mpps
Improvement of 6%.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the WQ API to get the WQ size, and to map a counter
into a WQ entry index.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If a TC rule needs to be split for mirroring, create two HW rules,
in the first level and the second level flow tables accordingly.
In the first level flow table, forward the packet to the mirror
port and forward the packet to the second level flow table for
further processing, eg. encap, vlan push or header re-write.
Currently the matching is repeated in both stages.
While here, simplify the setup of the vhca id valid indicator also
in the existing code.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we only support the mirred redirect TC sub-action. In order
to support flow based vport mirroring, add support to parse the mirred
mirror sub-action.
For mirroring, user-space will typically set the action order such that
the mirror port (mirror VF) sees packets as the original port (VF under
mirroring) sent them or as it will receive them.
In the general case, it means that packets are potentially sent to the
mirror port before or after some actions were applied on them. To
properly do that, we should follow on the exact action order as set for
the flow and make sure this will also be the case when we program the HW
offload.
We introduce a counter for the output ports (attr->out_count), which we
increase when parsing each mirred redirect/mirror sub-action and when
dealing with encap.
We introduce a counter (attr->mirror_count) telling us if split is
needed. If no split is needed and mirroring is just multicasting to
vport, the mirror count is zero, all the actions of the TC flow should
apply on that single HW flow.
If split is needed, the mirror count tells where to do the split, all
non-mirred tc actions should apply only after the split.
The mirror count is set while parsing the following actions encap/decap,
header re-write, vlan push/pop.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If firmware supports the forward action with a destination list
that includes a flow table, create a second level FDB flow table.
This is going to be used for flow based mirroring under the switchdev
offloads mode.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We have several fdb flow tables for each of the legacy and switchdev
modes. In the switchdev mode, there are fast path and slow path flow
tables. Towards adding more flow tables in upcoming patches, reorganize
and rename the various existing ones to reflect their functionality.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove redundant debug prints from phy_read/write since we can trace those
calls through trace events. Enhance dynamic debug prints to print arguments
which helps figuring how what is going on at the driver level with higher level
configuration interfaces.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series contains updates for mlx5e netdevice driver with one subject,
DSCP to priority mapping, in the first patch Huy adds the needed API in
dcbnl, the second patch adds the needed mlx5 core capability bits for the
feature, and all other patches are mlx5e (netdev) only changes to add
support for the feature.
From: Huy Nguyen
Dscp to priority mapping for Ethernet packet:
These patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
>> lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
>> lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbBy2YAAoJEEg/ir3gV/o+RkYIAId0h3GqVof41/qCHPuqx+7j
J/lTJSU+PHDZfVAuXhoQN5lFGsRku/wkqdSZNXxwvbUxVzIoUpxWvlaEv+481Cmj
+WhVC1QIExGYUs4CCGjgl853kNtGpDrZmk+olY3QaQISHdpcmgs/W13YlEKRyw5q
nFSa6GLA/3IQXb7eOwUiSW1gYYjn/eM2XFHntTTOeasa9dwb2QDqDQdoYiKdS+yS
KxqxrlADU4V+CtNlOmZ4QGxOa7suBBr+a6JvNnvviYOKKpYMNQRbhUbgu0pPdKAt
zbHHS7Twy1ka3s6CKk/QIT7/YWfCOQgWy6LGPCtUuGUA6dy5xsV7i2BtoDwMC7o=
=EJd2
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-05-19' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-19
This series contains updates for mlx5e netdevice driver with one subject,
DSCP to priority mapping, in the first patch Huy adds the needed API in
dcbnl, the second patch adds the needed mlx5 core capability bits for the
feature, and all other patches are mlx5e (netdev) only changes to add
support for the feature.
From: Huy Nguyen
Dscp to priority mapping for Ethernet packet:
These patches enable differentiated services code point (dscp) to
priority mapping for Ethernet packet. Once this feature is
enabled, the packet is routed to the corresponding priority based on its
dscp. User can combine this feature with priority flow control (pfc)
feature to have priority flow control based on the dscp.
Firmware interface:
Mellanox firmware provides two control knobs for this feature:
QPTS register allow changing the trust state between dscp and
pcp mode. The default is pcp mode. Once in dscp mode, firmware will
route the packet based on its dscp value if the dscp field exists.
QPDPM register allow mapping a specific dscp (0 to 63) to a
specific priority (0 to 7). By default, all the dscps are mapped to
priority zero.
Software interface:
This feature is controlled via application priority TLV. IEEE
specification P802.1Qcd/D2.1 defines priority selector id 5 for
application priority TLV. This APP TLV selector defines DSCP to priority
map. This APP TLV can be sent by the switch or can be set locally using
software such as lldptool. In mlx5 drivers, we add the support for net
dcb's getapp and setapp call back. Mlx5 driver only handles the selector
id 5 application entry (dscp application priority application entry).
If user sends multiple dscp to priority APP TLV entries on the same
dscp, the last sent one will take effect. All the previous sent will be
deleted.
This attribute combined with pfc attribute allows advanced user to
fine tune the qos setting for specific priority queue. For example,
user can give dedicated buffer for one or more priorities or user
can give large buffer to certain priorities.
The dcb buffer configuration will be controlled by lldptool.
>> lldptool -T -i eth2 -V BUFFER prio 0,2,5,7,1,2,3,6
maps priorities 0,1,2,3,4,5,6,7 to receive buffer 0,2,5,7,1,2,3,6
>> lldptool -T -i eth2 -V BUFFER size 87296,87296,0,87296,0,0,0,0
sets receive buffer size for buffer 0,1,2,3,4,5,6,7 respectively
After discussion on mailing list with Jakub, Jiri, Ido and John, we agreed to
choose dcbnl over devlink interface since this feature is intended to set
port attributes which are governed by the netdev instance of that port, where
devlink API is more suitable for global ASIC configurations.
The firmware trust state (in QPTS register) is changed based on the
number of dscp to priority application entries. When the first dscp to
priority application entry is added by the user, the trust state is
changed to dscp. When the last dscp to priority application entry is
deleted by the user, the trust state is changed to pcp.
When the port is in DSCP trust state, the transmit queue is selected
based on the dscp of the skb.
When the port is in DSCP trust state and vport inline mode is not NONE,
firmware requires mlx5 driver to copy the IP header to the
wqe ethernet segment inline header if the skb has it.
This is done by changing the transmit queue sq's min inline mode to L3.
Note that the min inline mode of sqs that belong to other features
such as xdpsq, icosq are not modified.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to free_netdev() in __rtl8139_cleanup_dev() clears the network device
napi list, and explicit calls to netif_napi_del() are unnecessary.
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In its current state, the driver will handle backing device
login in a loop for a certain number of retries while the
device returns a partial success, indicating that the driver
may need to try again using a smaller number of resources.
The variable it checks to continue retrying may change
over the course of operations, resulting in reallocation
of resources but exits without sending the login attempt.
Guard against this by introducing a boolean variable that
will retain the state indicating that the driver needs to
reattempt login with backing device firmware.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.
For example -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the supported classification modes [4 tuples based,
udp port based, src-ip based], flows can be classified
to the VFs as well. With this patch, flows can be re-directed
to the requested VF provided in "action" field of command.
Please note that driver doesn't really care about the queue bits
in "action" field for the VFs. Since queue will be still chosen
by FW using RSS hash. [I.e., the classification would be done
according to vport-only]
For examples -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action 0x100000000
ethtool -N p5p1 flow-type tcp4 src-ip 192.16.6.10 action 0x200000000
ethtool -U p5p1 flow-type tcp4 src-ip 192.168.40.100 dst-ip \
192.168.40.200 src-port 6660 dst-port 5550 \
action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver supports flow classification to PF
receive queues based on TCP/UDP 4 tuples [src_ip, dst_ip,
src_port, dst_port] only.
This patch enables to configure different flow profiles
[For example - only UDP dest port or src_ip based] on the
adapter so that classification can be done according to
just those fields as well. Although, at a time just one
type of flow configuration is supported due to limited
number of flow profiles available on the device.
For example -
ethtool -N enp7s0f0 flow-type udp4 dst-port 45762 action 2
ethtool -N enp7s0f0 flow-type tcp4 src-ip 192.16.4.10 action 1
ethtool -N enp7s0f0 flow-type udp6 dst-port 45762 action 3
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate and prevent some of the configurations for
unsupported [by firmware] inputs [for example - mac ext,
vlans, masks/prefix, tos/tclass] via ethtool -N/-U.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the ethtool rx flow configuration
[via ethtool -U/-N] flow code base by dividing it logically
into various APIs based on given protocols. It also separates
various validations and calculations done along the flow
in their own APIs.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a confusion of two different abstractions in the Common
Code: Physical Link (Port) and Logical Network Interface (Virtual
Interface), and we haven't been properly managing the state of the
intersection of those two abstractions.
On the one hand we have the Physical state of the Link -- up or down --
and on the other we have the logical state of the VI, enabled or not.
{ethN} refers to both the Physical and Logical State. In this case,
ifconfig only affects/interrogates the Logical State of a VI,
and ethtool only deals with the Physical State. And these are different.
So, just because we disable the VI, we don't really want to change the
Physical Link Up/Down state. Thus, the previous hack to set
"lc->link_ok = 0" when we disable a VI is completely incorrect.
Where we get into trouble is where the Physical Link State and the
Logical VI State cross swords. And that happens in
t4_handle_get_port_info() where we need to manage/safe the Physical
Link State, but we also need to know when the Logical VI State has
changed and pass that back up to the OS-dependent Driver routine
t4_os_link_changed() which is concerned about the Logical Interface.
So we enable a VI and that causes Firmware to send us a new Port
Information message, but if none of the Physical Link State
particulars have changed, we don't call t4_os_link_changed().
This fix uses the existing OS Contract APIs for the Common Code to
inform the OS-dependent portion of the Host Driver when the "Link" (really
Logical Network Interface) is "up" or "down". A new API
t4_enable_pi_params() is added which calls t4_enable_vi_params() and,
if that is successful, then calls back to the OS Contract API
t4_os_link_changed() notifying the OS-dependent layer of the
potential Link State change.
Original Work by : Casey Leedom <leedom@chelsio.com>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clean up init_one and use chip_ver consistently throughout
init_one() for chip version.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
newer SFPs like SFP28 and QSFP28 Transceiver Modules present
several new possibilities which we haven't faced before. Fix the
assumptions in the code reflecting the more limited capabilities
of previous Transceiver Module systems
Original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This comment is outdated as fec_ptp_ioctl has been replaced by fec_ptp_set/fec_ptp_get
since commit 1d5244d0e4 ("fec: Implement the SIOCGHWTSTAMP ioctl")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_enqueue_skb() can push new buffers for the xmit_more functionality.
We must stops the TX queue before this or else the TX queue does not get
restarted and we get a netdev watchdog.
In the error handling we may now need to unwind more than 1 packet, and
we may need to push the new buffers onto the partner queue.
v2: In the error leg also push this queue if xmit_more is set
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Reported-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a system is under memory presure (high usage with fragments),
the original 256KB ICM chunk allocations will likely trigger kernel
memory management to enter slow path doing memory compact/migration
ops in order to complete high order memory allocations.
When that happens, user processes calling uverb APIs may get stuck
for more than 120s easily even though there are a lot of free pages
in smaller chunks available in the system.
Syslog:
...
Dec 10 09:04:51 slcc03db02 kernel: [397078.572732] INFO: task
oracle_205573_e:205573 blocked for more than 120 seconds.
...
With 4KB ICM chunk size on x86_64 arch, the above issue is fixed.
However in order to support smaller ICM chunk size, we need to fix
another issue in large size kcalloc allocations.
E.g.
Setting log_num_mtt=30 requires 1G mtt entries. With the 4KB ICM chunk
size, each ICM chunk can only hold 512 mtt entries (8 bytes for each mtt
entry). So we need a 16MB allocation for a table->icm pointer array to
hold 2M pointers which can easily cause kcalloc to fail.
The solution is to use kvzalloc to replace kcalloc which will fall back
to vmalloc automatically if kmalloc fails.
Signed-off-by: Qing Huang <qing.huang@oracle.com>
Acked-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce infrastructure for supporting Factory Test Mode (FTM) of the
wireless LAN subsystem. In order for the user space to access the
firmware in test mode the relevant netlink channel needs to be exposed
from the kernel driver.
The above is achieved as follows:
1) Register wcn36xx driver to testmode callback from netlink
2) Add testmode callback implementation to handle incoming FTM commands
3) Add FTM command packet structure
4) Add handling for GET_BUILD_RELEASE_NUMBER (msgid=0x32A2)
5) Add generic handling for all PTT_MSG packets
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation
feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag.
This new features enables the ath10k host to send information to the
firmware on the specifications of detected radar type. This allows the
firmware to validate if the host's radar pattern detector unit is
operational and check if the radar information shared by host matches
the radar pulses sent as phy error events from firmware. If the check
fails the firmware won't allow use of DFS channels on AP mode when using
FCC regulatory region.
Hence this patch is mandatory when using a firmware from 10.4-3.6 branch.
Else, DFS channels on FCC regions cannot be used.
Supported Chipsets : QCA9984/QCA9888/QCA4019
Firmware Version : 10.4-3.6-00104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables ath10k/ath9k drivers to collect the specifications of the
radar type once it is detected by the dfs pattern detector unit.
Usage of the collected info is specific to driver implementation.
For example, collected radar info could be used by the host driver
to send to co-processors for additional processing/validation.
Note: 'radar_detector_specs' data containing the specifications of
different radar types which was private within dfs_pattern_detector/
dfs_pri_detector is now shared with drivers as well for making use
of this information.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a missing newline in wcn36xx_smd_send_and_wait() and also log the
command request and response type that was processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop the extra warning about failed allocations, both the core and the
only caller of this function will warn loud enough in such cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the interface is shut down, wcn36xx_smd_close() potentially races
against the queue worker. Make sure to cancel the work, and then free all
the remnants in hal_ind_queue manually.
This is again just a theoretical issue, not something that was triggered in
the wild.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a BSSID is joined, set the link status to 'preassoc', and set it to
'idle' when the BSS is deleted.
This is what the downstream driver is doing, and it seems to improve the
reliability during connect/disconnect stress tests.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In reap_tx_dxes(), when we iterate over the linked descriptors, only
consider such valid that have WCN36xx_DXE_CTRL_EOP set.
This is what the prima downstream driver is doing as well.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On RX and TX interrupts, check for the WCN36XX_CH_STAT_INT_ED_MASK or
WCN36XX_CH_STAT_INT_DONE_MASK in the interrupt reason register, and
only handle packets when it is set. This way, reap_tx_dxes() is only
invoked when needed.
This brings the dequeing logic in line with what the prima downstream
driver is doing.
While at it, also log the interrupt reason.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Like on the TX side, check for the interrupt reason when the RX interrupt
is latched and clear the ERR, DONE and ED masks.
This seems to help with connection timeouts and network stream
starvatations. And FWIW, the downstream driver does the same thing.
Note that in analogy to the TX side, WCN36XX_DXE_0_INT_CLR should be set to
WCN36XX_INT_MASK_CHAN_RX_{L,H} rather than WCN36XX_DXE_INT_CH{1,3}_MASK. It
did the right thing however, as the defines happen to have identical values.
Also, instead of determining register addresses and values inside
wcn36xx_rx_handle_packets(), pass them as arguments.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's no need to disable the IRQ from inside its handler.
Instead just grab the spinlock of the channel that is being processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The device takes 32-bit addresses only, so inform the DMA API about it.
This is the default on msm8016, so that doesn't change anything, but
it's best practice to be explicit.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When wcn36xx_dxe_tx_frame() is entered while the device is still processing
the queue asyncronously, we are racing against the firmware code with
updates to the buffer descriptors. Presumably, the firmware scans the ring
buffer that holds the descriptors and scans for a valid control descriptor,
and then assumes that the next descriptor contains the payload. If, however,
the control descriptor is marked valid, but the payload descriptor isn't,
the packet is not sent out.
Another issue with the current code is that is lacks memory barriers before
descriptors are marked valid. This is important because the CPU may reorder
writes to memory, even if it is allocated as coherent DMA area, and hence
the device may see incompletely written data.
To fix this, the code in wcn36xx_dxe_tx_frame() was restructured a bit so
that the payload descriptor is made valid before the control descriptor.
Memory barriers are added to ensure coherency of shared memory areas.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: ETSI -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: FCC -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
This change itself doesn't change the selected CTL of this country and is
only required to stay in sync with the QCA mappings.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't correctly
mapped to the actual CTL entries in EEPROM then it could happen that the
device violates the regulations. But it can also happen that the device is
then not able to be used with its full txpower on all rates.
The CTL mappings for this regdomain code were now changed to:
* 2.4GHz: ETSI
* 5GHz: NO_CTL -> ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regdomain code is used to select the correct the correct conformance
test limits (CTL) for a country. If the regdomain code isn't available and
it is still programmed in the EEPROM then it will cause an error and stop
the initialization with:
Invalid EEPROM contents
The current CTL mappings for this regdomain code are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: ETSI
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: FCC
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The country code is used by the ath to detect the ISO 3166-1 alpha-2 name
and to select the correct conformance test limits (CTL) for a country. If
the country isn't available and it is still programmed in the EEPROM then
it will cause an error and stop the initialization with:
Invalid EEPROM contents
The current CTL mappings for this country are:
* 2.4GHz: ETSI
* 5GHz: FCC
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.
Supported Chipsets:
-QCA988X/QCA9887 PCI
-QCA99X0/QCA9984/QCA9888/QCA4019 PCI
-QCA6174/QCA9377 PCI/USB/SDIO
-WCN3990 SNOC
Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware crash memory dump support for QCA9888 and QCA99X0.
Tested on:
QCA9888 firmware 10.4-3.5.3-00053
QCA99X0 firmware 10.4.1.00030-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the egress device of an offloaded rule is a LAG port, then encode the
output port to the NFP with a LAG identifier and the offloaded group ID.
A prelag action is also offloaded which must be the first action of the
series (although may appear after other pre-actions - e.g. tunnels). This
causes the FW to check that it has the necessary information to output to
the requested LAG port. If it does not, the packet is sent to the kernel
before any other actions are applied to it.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds the control message handler to synchronize offloaded group config
with that of the kernel. Such messages are sent from fw to driver and
feature the following 3 flags:
- Data: an attached cmsg could not be processed - store for retransmission
- Xon: FW can accept new messages - retransmit any stored cmsgs
- Sync: full sync requested so retransmit all kernel LAG group info
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Monitor LAG events via the NETDEV_CHANGEUPPER/NETDEV_CHANGELOWERSTATE
notifiers to maintain a list of offloadable groups. Sync these groups with
HW via a delayed workqueue to prevent excessive re-configuration. When the
workqueue is triggered it may generate multiple control messages for
different groups. These messages are linked via a batch ID and flags to
indicate a new batch and the end of a batch.
Update private data in each repr to track their LAG lower state flags. The
state of a repr is used to determine the active netdevs that can be
offloaded. For example, in active-backup mode, we only offload the netdev
currently active.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG upper event notifiers contain the tx type used by the LAG device.
Extend this to also include the hash policy used for tx types that
utilize hashing.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a bitmap to each flower repr to track its state if it is enslaved by a
bond. This LAG state may be different to the port state - for example, the
port may be up but LAG state may be down due to the selection in an
active/backup bond.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the fw contains the _abi_flower_balance_sync_enable symbol. If it
does then write a 1 to this indicating that the driver is willing to
receive NIC to kernel LAG related control messages.
If the write is successful, update the list of extra features supported by
the fw and add a stub to accept LAG cmsgs.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an rtsym API function that combines the lookup of a symbol and the
writing of a value to it. Values can be written as unsigned 32 or 64 bits.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a netdev to a bond requires that its mac address can be modified.
The default eth_mac_addr is sufficient to satisfy this requirement.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the guest network adapter is not configured with DeviceNaming
enabled on the host, then the query for friendly name will return
success but with a zero length name. Which then leads to a garbage value
(stack contents) for ifalias.
Fix is simple, just don't set name if host doesn't return it.
Fixes: 0fe554a46a ("hv_netvsc: propogate Hyper-V friendly name into interface alias")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 624dbf55a3 ("driver/net: enic: Try DMA 64 first, then
failover to DMA") DMA mask was changed from 40 bits to 64 bits.
Hardware actually supports only 47 bits.
Fixes: 624dbf55a3 ("driver/net: enic: Try DMA 64 first, then failover to DMA")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPPIOCDETACH ioctl effectively tries to "close" the given ppp file
before f_count has reached 0, which is fundamentally a bad idea. It
does check 'f_count < 2', which excludes concurrent operations on the
file since they would only be possible with a shared fd table, in which
case each fdget() would take a file reference. However, it fails to
account for the fact that even with 'f_count == 1' the file can still be
linked into epoll instances. As reported by syzbot, this can trivially
be used to cause a use-after-free.
Yet, the only known user of PPPIOCDETACH is pppd versions older than
ppp-2.4.2, which was released almost 15 years ago (November 2003).
Also, PPPIOCDETACH apparently stopped working reliably at around the
same time, when the f_count check was added to the kernel, e.g. see
https://lkml.org/lkml/2002/12/31/83. Also, the current 'f_count < 2'
check makes PPPIOCDETACH only work in single-threaded applications; it
always fails if called from a multithreaded application.
All pppd versions released in the last 15 years just close() the file
descriptor instead.
Therefore, instead of hacking around this bug by exporting epoll
internals to modules, and probably missing other related bugs, just
remove the PPPIOCDETACH ioctl and see if anyone actually notices. Leave
a stub in place that prints a one-time warning and returns EINVAL.
Reported-by: syzbot+16363c99d4134717c05b@syzkaller.appspotmail.com
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Reviewed-by: Guillaume Nault <g.nault@alphalink.fr>
Tested-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-05-24
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Björn Töpel cleans up AF_XDP (removes rebind, explicit cache alignment from uapi, etc).
2) David Ahern adds mtu checks to bpf_ipv{4,6}_fib_lookup() helpers.
3) Jesper Dangaard Brouer adds bulking support to ndo_xdp_xmit.
4) Jiong Wang adds support for indirect and arithmetic shifts to NFP
5) Martin KaFai Lau cleans up BTF uapi and makes the btf_header extensible.
6) Mathieu Xhonneux adds an End.BPF action to seg6local with BPF helpers allowing
to edit/grow/shrink a SRH and apply on a packet generic SRv6 actions.
7) Sandipan Das adds support for bpf2bpf function calls in ppc64 JIT.
8) Yonghong Song adds BPF_TASK_FD_QUERY command for introspection of tracing events.
9) other misc fixes from Gustavo A. R. Silva, Sirio Balmelli, John Fastabend, and Magnus Karlsson
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a recovery hard reset to handle reset failure as a result of
change of device context following a transport event, such as a
backing device failover or partition migration. These operations reset
the device context to its initial state. If this occurs during a reset,
any initialization commands are likely to fail with an invalid state
error as backing device firmware requests reinitialization.
When this happens, make one more attempt by performing a hard reset,
which frees any resources currently allocated and performs device
initialization. If a transport event occurs during a device reset, a
flag is set which will trigger a new hard reset following the
completionof the current reset event.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set device resetting state at the earliest possible point: as soon as a
reset is successfully scheduled. The reset state is toggled off when
all resets have been processed to completion.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of having one initialization routine for all cases, create
a separate, simpler function for standard initialization, such as during
device probe. Use the original initialization function to handle
device reset scenarios. The goal of this patch is to avoid having
a single, cluttered init function to handle all possible
scenarios.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting the link state is not successful, print a warning
with the resulting return code and return it to be handled
by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If device init is interrupted by a failover, set the init return
code so that it can be checked and handled appropriately by the
init routine.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether CRQ command is successful before awaiting a response
from the management partition. If the command was not successful, the
driver may hang waiting for a response that will never come.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an "active" state for a IBM vNIC Command-Response Queue. A CRQ
is considered active once it has initialized or linked with its partner by
sending an initialization request and getting a successful response back
from the management partition. Until this has happened, do not allow CRQ
commands to be sent other than the initialization request.
This change will avoid a protocol error in case of a device transport
event occurring during a initialization. When the driver receives a
transport event notification indicating that the backing hardware
has changed and needs reinitialization, any further commands other
than the initialization handshake with the VIOS management partition
will result in an invalid state error. Instead of sending a command
that will be returned with an error, print a warning and return an
error that will be handled by the caller.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set adapter NAPI state as disabled if they are removed. This will allow
them to be enabled again if reallocated in case of a hard reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
t4_prep_fw doesn't check for card_fw pointer before store the read data,
which could lead to a NULL pointer dereference if kvzalloc failed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch change the API for ndo_xdp_xmit to support bulking
xdp_frames.
When kernel is compiled with CONFIG_RETPOLINE, XDP sees a huge slowdown.
Most of the slowdown is caused by DMA API indirect function calls, but
also the net_device->ndo_xdp_xmit() call.
Benchmarked patch with CONFIG_RETPOLINE, using xdp_redirect_map with
single flow/core test (CPU E5-1650 v4 @ 3.60GHz), showed
performance improved:
for driver ixgbe: 6,042,682 pps -> 6,853,768 pps = +811,086 pps
for driver i40e : 6,187,169 pps -> 6,724,519 pps = +537,350 pps
With frames avail as a bulk inside the driver ndo_xdp_xmit call,
further optimizations are possible, like bulk DMA-mapping for TX.
Testing without CONFIG_RETPOLINE show the same performance for
physical NIC drivers.
The virtual NIC driver tun sees a huge performance boost, as it can
avoid doing per frame producer locking, but instead amortize the
locking cost over the bulk.
V2: Fix compile errors reported by kbuild test robot <lkp@intel.com>
V4: Isolated ndo, driver changes and callers.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Sandbox QP Commands are retired in the order they are sent. Outstanding
commands are stored in a linked-list in the order they appear. Once a
response is received and the callback gets called, we pull the first
element off the pending list, assuming they correspond.
Sending a message and adding it to the pending list is not done atomically,
hence there is an opportunity for a race between concurrent requests.
Bind both send and add under a critical section.
Fixes: bebb23e6cb ("net/mlx5: Accel, Add IPSec acceleration interface")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When RXFCS feature is enabled, the HW do not strip the FCS data,
however it is not present in the checksum calculated by the HW.
Fix that by manually calculating the FCS checksum and adding it to the SKB
checksum field.
Add helper function to find the FCS data for all SKB forms (linear,
one fragment or more).
Fixes: 102722fc68 ("net/mlx5e: Add support for RXFCS feature flag")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add dcbnl's set/get buffer configuration callback that allows user to
set/get buffer size configuration and priority to buffer mapping.
By default, firmware controls receive buffer configuration and priority
of buffer mapping based on the changes in pfc settings. When set buffer
call back is triggered, the buffer configuration changes to manual mode.
The manual mode means mlx5 driver will adjust the buffer configuration
accordingly based on the changes in pfc settings.
ConnectX buffer stride is 128 Bytes. If the buffer size is not multiple
of 128, the buffer size will be rounded down to the nearest multiple of
128.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add APIs for buffer configuration based on the changes in
pfc configuration, cable len, buffer size configuration,
and priority to buffer mapping.
Note that the xoff fomula is as below
xoff = ((301+2.16 * len [m]) * speed [Gbps] + 2.72 MTU [B]
xoff_threshold = buffer_size - xoff
xon_threshold = xoff_threshold - MTU
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Move four below functions from en_ethtool.c to en/port.c. These
functions are used by both en_ethtool.c and en_main.c. Future code
can use these functions without ethtool link mode dependency.
u32 mlx5e_port_ptys2speed(u32 eth_proto_oper);
int mlx5e_port_linkspeed(struct mlx5_core_dev *mdev, u32 *speed);
int mlx5e_port_max_linkspeed(struct mlx5_core_dev *mdev, u32 *speed);
u32 mlx5e_port_speed2linkmodes(u32 speed);
Delete the speed field from table mlx5e_build_ptys2ethtool_map. This
table only keeps the mapping between the mlx5e link mode and
ethtool link mode. Add new table mlx5e_link_speed for translation
from mlx5e link mode to actual speed.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux into for-next
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
* tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5e: Explicitly set source e-switch in offloaded TC rules
net/mlx5: Add source e-switch owner
net/mlx5e: Explicitly set destination e-switch in FDB rules
net/mlx5: Add destination e-switch owner
net/mlx5: Properly handle a vport destination when setting FTE
net/mlx5: Add merged e-switch cap
IB/mlx5: Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Eswitch, Use 'kvfree()' for memory allocated by 'kvzalloc()'
net/mlx5: Vport, Use 'kvfree()' for memory allocated by 'kvzalloc()'
After changing speed to 100Mbps as a result of auto-negotiation (AN),
some 10/100/1000Mbps SFPs indicate a successful link (no faults or loss
of signal), but cannot successfully transmit or receive data. These
SFPs required an extra auto-negotiation (AN) after the speed change in
order to operate properly. Add a quirk for these SFPs so that if the
outcome of the AN actually results in changing to a new speed, re-initiate
AN at that new speed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a quirk to make the BelFuse 1GBT-SFP06 part look like
a 1000baseX part, program the SFP PHY to support SGMII and 10/100/1000
baseT.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a KR re-driver is present, indicate the FEC support is available
during auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link training is always attempted when in KR mode, but the code is
structured to check if link training has been enabled before attempting
to perform it. Since that check will always be true, simplify the code
to always enable and start link training during KR auto-negotiation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to show and set the device channel configuration.
Changing the channel configuration will result in a device restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support being able to dynamically set/change the number of
Rx and Tx channels, update the code to:
- Move alloc and free of device memory into callable functions
- Move setting of the real number of Rx and Tx channels to device startup
- Move mapping of the RSS channels to device startup
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool support to show and set the number of the Rx and Tx ring
descriptors. Changing the ring configuration will result in a device
restart.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get SFP module information using ethtool.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently sets an indication of whether the SFP supports, and
that the driver can obtain, diagnostics data. This isn't currently used
by the driver and the logic to set this indicator is flawed because the
field is cleared each time the SFP is checked and only set when a new SFP
is detected. Remove this field and the logic supporting it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comm_owned field can hide logic where double locking is attempted
and prevent multiple threads for the same device from accessing the
mutex properly. Remove the comm_owned field and use the mutex API
exclusively for gaining ownership. The current driver has been audited
and is obtaining communications ownership properly.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Read and save the port property registers once during the device probe
and then use the saved values as they are needed.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A debug output print statement uses the wrong variable to output the
maximum Rx channel count (cut and paste error, basically). Fix the
statement to use the proper variable.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trigger an L1 configure operation when a transceiver module
is inserted in order to cause current "sticky" options like
Requested Forward Error Correction to be reapplied.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDI Port Capabilities bit definitions were inconsistent with
regard to the MDI enum values. 2 bits used to define MDI in
the port capabilities are not really separable, it's a 2-bit
field with 4 different values. Change the port capability bit
definitions to be "AUTO" and "STRAIGHT" in order to get them
to line up with the enum's.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* a fix for a race in aggregation, which I want to let
bake for a bit longer before sending to stable
* some new statistics (ACK RSSI, TXQ)
* TXQ configuration
* preparations for HE, particularly radiotap
* replace confusing "country IE" by "country element" since it's
not referring to Ireland
Note that I merged net-next to get a fix from mac80211 that got
there via net, to apply one patch that would otherwise conflict.
-----BEGIN PGP SIGNATURE-----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=G98y
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2018-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
For this round, we have various things all over the place, notably
* a fix for a race in aggregation, which I want to let
bake for a bit longer before sending to stable
* some new statistics (ACK RSSI, TXQ)
* TXQ configuration
* preparations for HE, particularly radiotap
* replace confusing "country IE" by "country element" since it's
not referring to Ireland
Note that I merged net-next to get a fix from mac80211 that got
there via net, to apply one patch that would otherwise conflict.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_lock/unlock was used instead of spin_un/lock_irq
in a procedure used in process space, on a spinlock
which can be grabbed in an interrupt.
This caused the stack trace below to be displayed (on kernel
4.17.0-rc1 compiled with Lock Debugging enabled):
[ 154.661474] WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected
[ 154.668909] 4.17.0-rc1-rdma_rc_mlx+ #3 Tainted: G I
[ 154.675856] -----------------------------------------------------
[ 154.682706] modprobe/10159 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
[ 154.690254] 00000000f3b0e495 (&(&qp_table->lock)->rlock){+.+.}, at: mlx4_qp_remove+0x20/0x50 [mlx4_core]
[ 154.700927]
and this task is already holding:
[ 154.707461] 0000000094373b5d (&(&cq->lock)->rlock/1){....}, at: destroy_qp_common+0x111/0x560 [mlx4_ib]
[ 154.718028] which would create a new lock dependency:
[ 154.723705] (&(&cq->lock)->rlock/1){....} -> (&(&qp_table->lock)->rlock){+.+.}
[ 154.731922]
but this new dependency connects a SOFTIRQ-irq-safe lock:
[ 154.740798] (&(&cq->lock)->rlock){..-.}
[ 154.740800]
... which became SOFTIRQ-irq-safe at:
[ 154.752163] _raw_spin_lock_irqsave+0x3e/0x50
[ 154.757163] mlx4_ib_poll_cq+0x36/0x900 [mlx4_ib]
[ 154.762554] ipoib_tx_poll+0x4a/0xf0 [ib_ipoib]
...
to a SOFTIRQ-irq-unsafe lock:
[ 154.815603] (&(&qp_table->lock)->rlock){+.+.}
[ 154.815604]
... which became SOFTIRQ-irq-unsafe at:
[ 154.827718] ...
[ 154.827720] _raw_spin_lock+0x35/0x50
[ 154.833912] mlx4_qp_lookup+0x1e/0x50 [mlx4_core]
[ 154.839302] mlx4_flow_attach+0x3f/0x3d0 [mlx4_core]
Since mlx4_qp_lookup() is called only in process space, we can
simply replace the spin_un/lock calls with spin_un/lock_irq calls.
Fixes: 6dc06c08be ("net/mlx4: Fix the check in attaching steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning reported by checkpatch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the GPLv2 license boilerplate with the SPDX license identifier.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement adjust_link function that allows to overwrite default CPU port
setting using fixed-link device tree subnode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is brought up/down do not enable/disable only the TXMAC
but the RXMAC as well. This is essential for the CPU port to work.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 0x6088 and 0x6089 device ids for new T6 cards.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613e ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently doing auxiliary control register reads with the shadow
register value 0b111 (0x7) which incidentally is also the selector value
that should be present in bits [2:0]. Fix this by using the appropriate
selector mask which is defined (MII_BCM54XX_AUXCTL_SHDWSEL_MASK).
This does not have a functional impact yet because we always access the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC (0x7) register in the current code.
This might change at some point though.
Fixes: 5b4e290051 ("net: phy: broadcom: add bcm54xx_auxctl_read")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in mlx4_dbg debug message and also
change the phrasing of the message so that is is more readable
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handlers for ethtool get/set msg level are missing from netvsc.
This patch adds them.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling the sub-CRQ IRQ a previous update sent a H_EOI prior
to the enablement to clear any pending interrupts that may be present
across a partition migration. This fixed a firmware bug where a
migration could erroneously indicate that a H_EOI was pending.
The H_EOI should only be sent when enabling during a mobility
event though. Doing so at other time could wrong and can produce
extra driver output when IRQs are enabled when doing TX completion.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename VXGE_HW_ERR_PRIVILAGED_OPEARATION to VXGE_HW_ERR_PRIVILEGED_OPERATION
to fix spelling mistake.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until the udp receive stack supports large packets (UDP GRO), GSO
packets must not loop from the egress to the ingress path.
Revert the change that added NETIF_F_GSO_UDP_L4 to various virtual
devices through NETIF_F_GSO_ENCAP_ALL as this included devices that
may loop packets, such as veth and macvlan.
Instead add it to specific devices that forward to another device's
egress path, bonding and team.
Fixes: 83aa025f53 ("udp: add gso support to virtual devices")
CC: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the i2c-bus property mandatory when using a device
tree. If the sfp i2c bus isn't described it's impossible to guess the
protocol to use for a given module, and the sfp module would then not
work in most cases.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case no Tx disable pin is available the SFP modules will always be
emitting. This could be an issue when using modules using laser as their
light source as we would have no way to disable it when the fiber is
removed. This patch adds a warning when registering an SFP cage which do
not have its tx_disable pin wired or available.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link is down, writes to the device might fail with
-EIO. Userspace needs an indication when the status is resolved. As a
fix, tun_net_open() attempts to wake up writers - but that is only
effective if SOCKWQ_ASYNC_NOSPACE has been set in the past. This is
not the case of vhost_net which only poll for EPOLLOUT after it meets
errors during sendmsg().
This patch fixes this by making sure SOCKWQ_ASYNC_NOSPACE is set when
socket is not writable or device is down to guarantee EPOLLOUT will be
raised in either tun_chr_poll() or tun_sock_write_space() after device
is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Fixes: 1bd4978a88 ("tun: honor IFF_UP in tun_get_user()")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NFP is modelled as a switch we assign phys_port_name to respective
port(representor )s:
vNIC0 - | - PF port (pf%d) MAC/PHY (p%d[s%d]) - |E==
In most cases there is only one vNIC for communication with the switch.
If there is more than one we need to be able to identify them. Use %d
as phys_port_name of the vNICs.
We don't have to pass ID to nfp_net_debugfs_vnic_add() separately any
more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI PFs can host more than one logical endpoint. In NFP terms
this means having more than one vNIC for PCIe PF. The vNICs
are usually corresponding 1:1 to Ethernet ports. In core NIC
we use the legacy idea of vNIC *being* the Ethernet port,
hence netdevs put pX(sY) in their phys_port_name, like Ethernet
ports would. When ASIC ports are fully represented we need to
be able to name different PCIe PF ports, too. Use a scheme
similar to Ethernet ports - pfXsY, for PCIe PF number X,
sub-port Y.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current control firmware does not cater too well to multi-host
applications. There is no way to check which hosts are up or
otherwise negotiate what the state of the external port (the
Ethernet port) should be. Make sure the link is up when driver
loads, and don't take it down when Ethernet port netdev is
closed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To configure buffering points we need full set of netdevs:
ASIC
user netdev -- | -- PCIe port MAC port -- | --
Configuring egrees qdiscs on user netdev configures standard
Linux TC software qdiscs, configuring PCIe port qdiscs will
provide a way of setting ASIC queuing parameters for PCIe block.
MAC port netdev egress qdiscs correspond to ASIC MAC Traffic
Manager block.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our previous apps all assumed to use only one eswitch mode (legacy
or switchdev) without the ability to change it. ABM NIC will
want to support the switch so plumb devlink_eswitch_mode_set through.
The devlink_eswitch_mode_set is expected to spawn representors and
potentially devlink ports so it's called under big devlink lock and
pf->lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_apps can currently associate their structures with vNICs but
not representors. Add app priv pointer to representors as well.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ABM NIC requires more complex vNIC handling, allocate
per-vNIC structure. Find out RX queue base and PCI PF id.
There will be multiple PFs sharing the same MAC port, therefore
the MAC address assigned to the vNIC must be looked up in the
HWInfo database.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a very rudimentary active buffer management NIC support.
For now it's like a core NIC without SR-IOV support. Next
commits will extend its functionality.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code doesn't enforce length requirements on 32bit accesses
with action NFP_CPP_ACTION_RW to memory units, but if the access
is only aligned to 4 bytes as well we will fall into the explicit
access case and error out. Such accesses are correct, allow them
by lowering the width earlier.
While at it use a switch statement to improve readability.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow app FW to advertise its shared buffer pool information.
Use the per-PF mailbox to configure them from devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working with devlink-related functionality for locking reasons
it's easier to create a new mailbox per-PCI PF device than try to
use one of the netdev/vNIC mailboxes.
Define new mailbox structure and resolve its symbol during probe.
For forward compatibility allow silent truncation of mailbox command
data.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_net_pf_rtsym_read_optional() and nfp_net_pf_map_rtsym() are not
really related to networking code. Move them to the PF code and
remove the net from their names. They will soon be needed by code
outside of nfp_net_main.c anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to drop refcnt to xdp_page if we see a gso packet. Otherwise
it will be leaked. Fixing this by moving the check of gso packet above
the linearizing logic. While at it, remove useless comment as well.
Cc: John Fastabend <john.fastabend@gmail.com>
Fixes: 72979a6c35 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we successfully linearize the packet, num_buf will be set to zero
which may confuse error handling path which assumes num_buf is at
least 1 and this can lead the code tries to pop the descriptor of next
buffer. Fixing this by checking num_buf against 1 before decreasing.
Fixes: 4941d472bf ("virtio-net: do not reset during XDP set")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not go for the error path after successfully transmitting a
XDP buffer after linearizing. Since the error path may try to pop and
drop next packet and increase the drop counters. Fixing this by simply
drop the refcnt of original page and go for xmit path.
Fixes: 72979a6c35 ("virtio_net: xdp, add slowpath case for non contiguous buffers")
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After a linearized packet was redirected by XDP, we should not go for
the err path which will try to pop buffers for the next packet and
increase the drop counter. Fixing this by just drop the page refcnt
for the original page.
Fixes: 186b3c998c ("virtio-net: support XDP_REDIRECT")
Reported-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attempt to dump dongle memory for debug upon receiving firmware halt
message through dongle to host mail box interrupt.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe dongle firmware signals a halt/trap through mailbox interrupt.
Trigger a memory dump upon receiving such signal could help to provide
useful information for issue debug.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In patch "brcmfmac: add support for sysfs initiated coredump", a new
scenario of brcmf_debug_create_memdump was added in which the user of
the function might not necessarily provide prefix data. Hence the
function should not assume the data is always valid and should perform a
check before copying.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 3c47d19ff4 ("drivers: base: add coredump driver ops")
it is possible to initiate a device coredump from user-space. This
patch adds support for it adding the .coredump() driver callback.
As there is no longer a need to initiate it through debugfs remove
that code.
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver already supports device coredump initiated by firmware
event. Since commit 3c47d19ff4 ("drivers: base: add coredump driver
ops") it is also possible to initiate it from user-space through
sysfs. This patch adds support for SDIO and PCIe devices.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The only user of ALLFFMAC is the flowring module so no need to
expose it in a header file.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* hwsim radio dump wasn't working for the first radio
* mesh was updating statistics incorrectly
* a netlink message allocation was possibly too short
* wiphy name limit was still too long
* in certain cases regdb query could find a NULL pointer
-----BEGIN PGP SIGNATURE-----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=KWsp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-05-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* hwsim radio dump wasn't working for the first radio
* mesh was updating statistics incorrectly
* a netlink message allocation was possibly too short
* wiphy name limit was still too long
* in certain cases regdb query could find a NULL pointer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are specific cases, such as SAE authentication exchange, that
might require long duration to complete. For such cases, add support
for indicating to the driver the required duration of the prepare_tx()
operation, so the driver would still be able to complete the frame
exchange.
Currently, indicate the duration only for SAE authentication exchange,
as SAE authentication can take up to 2000 msec (as defined in IEEE
P802.11-REVmd D1.0 p. 3504).
As the patch modified the prepare_tx() callback API, also modify
the relevant code in iwlwifi.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Bring in net-next which had pulled in net, so I have the changes
from mac80211 and can apply a patch that would otherwise conflict.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Auto rate table sent to firmware is getting corrupted
as memset to zeros is not done. Added memset to skb
data before filling auto rate table.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed crash in some scenarios when assertion has occurred,
this is because hw structure is freed and is tried to get
accessed in some functions where null check is already
present. So, avoided the crash by making the hw to NULL after
freeing.
Signed-off-by: Sanjay Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Sushant Kumar Mishra <sushant.mishra@redpinesignals.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows reading all capabilities as reported by a firmware. They are
printed using native (raw) names, just like developers like it the most.
It's how firmware reports support for various features, e.g. supported
modes, supported standards, power saving details, max BSS-es.
Access to all that info is useful for trying new firmwares, comparing
them and debugging features AKA bugs.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Correct snr/nr/rssi data index to avoid possible buffer underflow.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usleep_range can cause excessive latency on channel change if waiting
for the MAC to stop fails. It will be forced to stop by the code
following that loop anyway.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allows it to be shared between different drivers and locks to be
initialized earlier
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During scans, mac80211 frequently switches back to the home channel to
minimize interruption of ongoing traffic. Keep regular tx queues active
during that time.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the radio was previously in running state, it can receive some
packets before it is able to process them.
This can lead to a crash if the channel is not initialized yet.
Discard all rx packets until start() is called
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For encryption to work properly, the BSS index needs to be initialized
for the WCID entry used for the interface.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
According to 802.11-2007 17.3.8.6 (slot time), the slot time should
be increased by 3 us * coverage class. Taking into account coverage
class in slot time configuration allows to increase by an order of
magnitude the throughput on a 4Km link in a noisy environment
Tested-by: Luca Bisti <luca.bisti@gmail.com>
Tested-by: Gaetano Catalli <gaetano.catalli@gmail.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git patches for 4.18. Major changes:
ath10k
* add quiet mode support for QCA6174/QCA9377
wil6210
* disable WIL6210_TRACING kconfig option by default
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-05-22
This series contains updates to i40e only.
Jake provides all the changes in this series starting with making it
consistent in how we approach the bit lock. Fixed the reporting of the
VEB statistics and the queue statistics to always return every queue
even if it is not currently in use. Use WARN_ONCE() so that the first
time we end up with an incorrect size we will dump a stack trace and a
message to help highlight the issue early in testing. Folded the fixed
string prefix into the stat string definition. Instead of using a
separate char *p pointer when copying strings, use the data pointer
directly. Added code comments for several of the statistic functions to
better explain the number and ordering of statistics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to invoke pci_disable_device() when errors occur in
pcnet32_probe_pci().
Signed-off-by: Bo Chen <chenbo@pdx.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle append for gateway based routes. Dev-only multipath routes will
be handled by a follow on patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is no license information in the header of
this file.
The MODULE_LICENSE field contains ("GPL"), which means
GNU Public License v2 or later, so add a corresponding
SPDX license identifier.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use i as an array index for the data variable,
replace the use of 'j' with 'i' so that we match the general loop
variable name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add documentation for the i40e_get_stats_count, i40e_get_stat_strings
and i40e_get_ethtool_stats explaining that the number and ordering of
statistics must remain constant for a given netdevice.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to add a helper function i40e_add_ethtool_stats
that will help lower the amount of boiler plate code in the
i40e_get_ethtool_stats function.
This conversion will take place over many patches, and the helper
function will work by directly updating a reference to the data pointer.
Since this would not work combined with the current method of accessing
data like an array, update all the code that copies stats into the data
buffer to use direct updates to the pointer instead of array accesses.
This will prevent incorrect stat updates for patches in between the
conversion.
Similarly, when copying strings, we used a separate char *p pointer.
Instead, use the data pointer directly as it's already a (u8 *) type
which is the same size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always prefix these stats with a fixed string, so just fold this
prefix into the stat string definition. This preparatory work will make
it easier to implement a helper function to copy stats and strings into
the supplied buffers in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't really want to use BUG_ON here since that would completely
crash the kernel, thus the reason we commented it out. We *can't* use
BUILD_BUG_ON because at least now (a) the sizes aren't constant (we are
fixing this) and (b) not all compilers are smart enough to understand
that "p - data" is a constant.
Instead, just use a WARN_ONCE so that the first time we end up with an
incorrect size we will dump a stack trace and a message, hopefully
highlighting the issues early in testing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the statistic strings and private flags strings into their own
separate functions to aid code readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the queue statistics to always return
every queue even if it's not currently in use.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the VEB statistics strings to always be
reported. Other issues will be fixed in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the same logic to free the skb after clearing the Tx timestamp bit
lock in i40e_ptp_stop as we use in the other locations. It is not as
important here since we are not racing against a future Tx timestamp
request (as we are disabling PTP at this point). However it is good to
be consistent in how we approach the bit lock so that future callers
don't copy the old anti-pattern.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since 6335698e24 the radio with idx of 0
will not get dumped in HWSIM_CMD_GET_RADIO because of the last_idx
checks. Offset cb->args[0] by 1 similarly to what is done in nl80211.c.
Fixes: 6335698e24 ("mac80211_hwsim: add generation count for netlink dump operation")
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that we can compile test this driver on 64-bit hosts, we get some
warnings about how a pointer/address is written/read to/from a register
(sw_token). Fix this by doing the appropriate conversions, we cannot
possibly have the driver work on 64-bit hosts the way the tokens are
managed though, since the registers being written to a 32-bit only.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pa which is the correct formatter to print a physical address,
instead of %p which is just a pointer.
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building on a 64-bit host we will get the following warning:
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_add_ch_strings':
drivers/net/ethernet/ti/cpsw.c:1284:19: warning: format '%d' expects
argument of type 'int', but argument 5 has type 'long unsigned int'
[-Wformat=]
"%s DMA chan %d: %s", rx_dir ? "Rx" : "Tx",
~^
%ld
Fix this by using an %ld format and casting to long.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit hosts we will get the following warning:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_overflow_check':
drivers/net/ethernet/ti/cpts.c:297:11: warning: format '%lld' expects
argument of type 'long long int', but argument 3 has type
'__kernel_time_t {aka long int}' [-Wformat=]
pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec,
ts.tv_nsec);
Fix this by using an appropriate casting that works on all bit sizes.
Fixes: a5c79c26e1 ("ptp: cpts: convert to the 64 bit get/set time methods.")
Fixes: 87c0e764d4 ("cpts: introduce time stamping code and a PTP hardware clock.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can compile davinci_cpdma.c on 64-bit hosts, we can see that
the format used for printing a size_t type is incorrect, use %zd
accordingly.
Fixes: aeec302104 ("net: ethernet: ti: cpdma: remove used_desc counter")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
immdlen field of FW_ETH_TX_PKT_WR is filled in a wrong way,
we must copy the length of all the cpls encapsulated in fw
work request. In the xmit path we missed adding the length
of CPL_TX_PKT_CORE but we added the length of WR_HDR and it
worked because WR_HDR and CPL_TX_PKT_CORE are of same length.
Add the length of cpl_tx_pkt_core not WR_HDR's. This also
fixes the lso cpl errors for udp tunnels
Fixes: d0a1299c6b ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of entries were not alphabetically sorted, remedy that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_GPIOLIB is disabled, gpiod_put() becomes a stub that produces a
warning, this helped identify that we could be attempting to release a NULL
pl->link_gpio GPIO descriptor, so guard against that.
Fixes: daab3349ad ("net: phy: phylink: Release link GPIO")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mv88e6xxx_probe(), ("np" or "pdata") might be an invariant
but GCC can't see that, therefore:
drivers/net/dsa/mv88e6xxx/chip.c: In function ‘mv88e6xxx_probe’:
drivers/net/dsa/mv88e6xxx/chip.c:4420:13: warning: ‘compat_info’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip->info = compat_info;
Actually, it should have warned on the "if (!compat_info)" test, but
whatever.
Explicitly initialize to NULL in the variable declaration to
deal with this.
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the size of the EEPROM to the platform data, so it can also be
instantiated by a platform device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all the world uses device tree. Some parts of the world still use
platform devices and platform data. Add basic support for probing a
Marvell switch via platform data.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IRQ domain will work without an OF node. It is not possible to
reference interrupts via a phandle, but C code can still use
irq_find_mapping() to get an interrupt from the domain.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon has noticed a typo in the comment accompaining the BCULR write --
fix it and move the comment before the write (following the style of
the other comments), while at it...
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the verbs in the comments to the 'struct sh_eth_cpu_data' declaration
should be in a 3rd person singular, to match the nouns.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the EESR bit 8 is TRO (transmit retry over), not RTO.
Note that EESIPR bit 8, TROIP remained correct...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vf module is loading, the cmd queue initialization should
happen before misc interrupt initialization, otherwise the misc
interrupt handle will cause using uninitialized cmd queue problem.
There is also the same issue when vf module is unloading.
This patch fixes it by adjusting the location of some function.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_ARM_SMMU_V3 is enabled, arm64's dma_ops will replace
arm64_swiotlb_dma_ops with iommu_dma_ops. When releasing contiguous
dma memory, the new ops will call the vunmap function which cannot
be run in interrupt context.
Currently, spin_lock_bh is called before vunmap is executed. This
disables BH and causes the interrupt context to be detected to
generate a kernel panic like below:
[ 2831.573400] kernel BUG at mm/vmalloc.c:1621!
[ 2831.577659] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 2831.699907] Process rmmod (pid: 1893, stack limit = 0x0000000055103ee2)
[ 2831.706507] Call trace:
[ 2831.708941] vunmap+0x48/0x50
[ 2831.711897] dma_common_free_remap+0x78/0x88
[ 2831.716155] __iommu_free_attrs+0xa8/0x1c0
[ 2831.720255] hclge_free_cmd_desc+0xc8/0x118 [hclge]
[ 2831.725128] hclge_destroy_cmd_queue+0x34/0x68 [hclge]
[ 2831.730261] hclge_uninit_ae_dev+0x90/0x100 [hclge]
[ 2831.735127] hnae3_unregister_ae_dev+0xb0/0x868 [hnae3]
[ 2831.740345] hns3_remove+0x3c/0x90 [hns3]
[ 2831.744344] pci_device_remove+0x48/0x108
[ 2831.748342] device_release_driver_internal+0x164/0x200
[ 2831.753553] driver_detach+0x4c/0x88
[ 2831.757116] bus_remove_driver+0x60/0xc0
[ 2831.761026] driver_unregister+0x34/0x60
[ 2831.764935] pci_unregister_driver+0x30/0xb0
[ 2831.769197] hns3_exit_module+0x10/0x978 [hns3]
[ 2831.773715] SyS_delete_module+0x1f8/0x248
[ 2831.777799] el0_svc_naked+0x30/0x34
This patch fixes it by using spin_lock instead of spin_lock_bh.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does bit of a clean-up by using already defined enums for
certain values in function hclge_is_special_opcode(). Below enums from
have been used as replacements for magic values:
enum hclge_opcode_type{
<snip>
HCLGE_OPC_STATS_64_BIT = 0x0030,
HCLGE_OPC_STATS_32_BIT = 0x0031,
HCLGE_OPC_STATS_MAC = 0x0032,
<snip>
};
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:
[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34
This patch fixes it by adding module version info.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing initialization of the client list node
in the hnae3_register_client() function.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the goto and directly returns in case of errors as part of the
cleanup.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the RX leg driver needs to fetch the ethernet header
length from the RX'ed Buffer Descriptor. Currently, proprietary
version hns3_nic_get_headlen is being used to fetch the header
length which uses l234info present in the Buffer Descriptor
which might not be valid for the first Buffer Descriptor if the
packet is spanning across multiple descriptors.
Kernel default eth_get_headlen API does the job correctly.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the error reported by Intel's kbuild and fixes a
return value in one of the legs, caught during review of the original
patch sent by kbuild.
Fixes: fdb793670a00 ("net: hns3: Add support of .sriov_configure in HNS3 driver")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit removed calls to rtl_set_rx_mode(). This is ok for the
standard path if the link is brought up, however it breaks system
resume from suspend. Link comes up but no network traffic.
Meanwhile common code from rtl_hw_start_8169/8101/8168() was moved
to rtl_hw_start(), therefore re-add the call to rtl_set_rx_mode()
there.
Due to adding this call we have to move definition of rtl_hw_start()
after definition of rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 82d3ff6dd1 ("r8169: remove calls to rtl_set_rx_mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 6710f970d9.
Gotta love when developers have offline discussions, thinking everyone
is reading their responses/dialog.
The change had the potential for a number of race conditions on
shutdown, which is why we are reverting the change.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use non-NUMA aware allocation for TPD and RRD buffers,
this patch modifies to use NUMA friendly allocation.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, add support for the DT probing of the R-Car V3H (AKA R8A77980) --
it's the only R-Car gen3 SoC having the GEther controller -- others have
only EtherAVB...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (AKA R8A77980) GEther controller adds the DMA burst mode bit
(NBST) in EDMR and the manual tells to always set it before doing any DMA.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The R-Car V3H (AKA R8A77980) GEther controller adds support for the RGMII
PHY interface mode as a new value for the RMII_MII register.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 Header Parser sets some bits in the 'result_info' field in
each lookup iteration, to identify different packet attributes such as
DSA / VLAN tag, protocol infos, etc. This is used in further
classification stages in the controller.
It's the DSA tag detection entry that is in charge of detecting when there
is a single VLAN tag.
This commits adds the missing update of the result_info in this case.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since devlink knows the info needed to generate the physical port name
in a generic way for all devlink users, use the helper to do the job.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Devlink ports can have specific flavour according to the purpose of use.
This patch extend attrs_set so the driver can say which flavour port
has. Initial flavours are:
physical, cpu, dsa
User can query this to see right away what is the purpose of each port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change existing setter for split port information into more generic
attrs setter. Alongside with that, allow to set port number and subport
number for split ports.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code logic is similar with arithmetic right shift by constant, and NFP
get indirect shift amount through source A operand of PREV_ALU.
It is possible to fall back to logic right shift if the MSB is known to be
zero from range info, however there is no benefit to do this given logic
indirect right shift use the same number and cycle of instruction sequence.
Suppose the MSB of regX is the bit we want to replicate to fill in all the
vacant positions, and regY contains the shift amount, then we could use
single instruction to set up both.
[alu, --, regY, OR, regX]
--
NOTE: the PREV_ALU result doesn't need to write to any destination
register.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Code logic is similar with logic right shift except we also need to set
PREV_ALU result properly, the MSB of which is the bit that will be
replicated to fill in all the vacant positions.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
For indirect shifts, shift amount is not specified as constant, NFP needs
to get the shift amount through the low 5 bits of source A operand in
PREV_ALU, therefore extra instructions are needed compared with shifts by
constants.
Because NFP is 32-bit, so we are using register pair for 64-bit shifts and
therefore would need different instruction sequences depending on whether
shift amount is less than 32 or not.
NFP branch-on-bit-test instruction emitter is added by this patch and is
used for efficient runtime check on shift amount. We'd think the shift
amount is less than 32 if bit 5 is clear and greater or equal than 32
otherwise. Shift amount is greater than or equal to 64 will result in
undefined behavior.
This patch also use range info to avoid generating unnecessary runtime code
if we are certain shift amount is less than 32 or not.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Some HW specific setups, like sun8i, do not populate all the necessary
callbacks, which is what HWIF helpers were expecting.
Fix this by always trying to get the generic helpers and populate them
if they were not previously populated by HW specific setup.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: 5f0456b431 ("net: stmmac: Implement logic to automatically
select HW Interface")
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the indirect register offsets in collecting TX rate limit info
in UP CIM logs.
Also, T5 doesn't support these indirect register offsets, so remove
them from collection logic.
Fixes: be6e36d916 ("cxgb4: collect TX rate limit info in UP CIM logs")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For T6, collect info on queue mapping to corresponding PF/VF in SGE.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch on the Marvell PPv2 driver is only cosmetic. Two typos are
removed as well as other cosmetic fixes, such as extra new lines or tabs
vs spaces.
Suggested-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 9b5ba0df4e ("ARM: shmobile: Introduce ARCH_RENESAS")
is CONFIG_ARCH_RENESAS a more appropriate platform check than the legacy
CONFIG_ARCH_SHMOBILE, hence use the former.
Renesas SuperH SH-Mobile SoCs are still covered by the CONFIG_CPU_SH4
check.
This will allow to drop ARCH_SHMOBILE on ARM and ARM64 in the near
future.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in printk message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Or Gerlitz <ogerlitz@mellanox.com>
This series addresses a regression introduced by the
shared block TC changes [1]. Currently, for VF->VF and uplink->VF rules, the
TC core (cls_api) attempts to offload the same flow multiple times into
the driver, as a side effect of the mlx5 registration to the egdev callback.
We use the flow cookie to ignore attempts to add such flows, we can't
reject them (return error), b/c this will fail the offload attempt, so we
ignore that.
The last patch of the series deals with exposing HW stats counters through
ethtool for the vport reps.
Dave - the regression that we are addressing was introduced in 4.15 [1] and applies
to nfp and mlx5. Jiri suggested to push driver side fixes to net-next, this is
already done for nfp [2][3]. Once this is upstream, we will submit a small/point
single patch fix for the TC core code which can serve for net and stable, but not
carried into net-next, b/c it might limit some future use-cases.
[1] 208c0f4b52 "net: sched: use tc_setup_cb_call to call per-block callbacks"
[2] c50647d "nfp: flower: ignore duplicate cb requests for same rule"
[3] 54a4a03 "nfp: flower: support offloading multiple rules with same cookie"
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/iMHAAoJEEg/ir3gV/o+6YcIAMIcUmH0Yga2CQLl1VGZr4v7
5Yo5z8upZ2pKVlBNtgeDonIckcFNbtPaUC7xTolFmOks6DgoGKKLvrIyq3tNG+42
ShF91BmLvrpl/+8GmsjNf5qvsmc6piOHfBknlaIl7XeoaKLMfy4ts7/Cryt0U24k
meE/zu7slOOam6H2RyXKLsJa0uP/SpxrCq1OAlAwhmVe60p9SRCVkutmRqU47OuO
Oc3XGtYbU3IVa3B0bdi+SdOyF1RykCH3PKSrChy2WhdfpSp29I+gydfWMX8/3+z4
mH3/LDi4CAoHiCqnUr3s5h6zGuYqwcpSYY3tUPUD3A48LnKjT70LJF85F/v7exY=
=QeXI
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-17
From: Or Gerlitz <ogerlitz@mellanox.com>
This series addresses a regression introduced by the
shared block TC changes [1]. Currently, for VF->VF and uplink->VF rules, the
TC core (cls_api) attempts to offload the same flow multiple times into
the driver, as a side effect of the mlx5 registration to the egdev callback.
We use the flow cookie to ignore attempts to add such flows, we can't
reject them (return error), b/c this will fail the offload attempt, so we
ignore that.
The last patch of the series deals with exposing HW stats counters through
ethtool for the vport reps.
Dave - the regression that we are addressing was introduced in 4.15 [1] and applies
to nfp and mlx5. Jiri suggested to push driver side fixes to net-next, this is
already done for nfp [2][3]. Once this is upstream, we will submit a small/point
single patch fix for the TC core code which can serve for net and stable, but not
carried into net-next, b/c it might limit some future use-cases.
[1] 208c0f4b52 "net: sched: use tc_setup_cb_call to call per-block callbacks"
[2] c50647d "nfp: flower: ignore duplicate cb requests for same rule"
[3] 54a4a03 "nfp: flower: support offloading multiple rules with same cookie"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ocelot_qsys.h is missing the SPDX identfier, fix that.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Allan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the if condition and check if return code is different
than -EINVAL, meaning callback is present.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop using if conditions depending on the GMAC version for getting the
descriptor skbuff address and use instead a helper implemented in the
descriptor files.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently an if condition is used to select the correct callback to set
rx_onwer in descriptor. Lets keep this simple and always use the same
callback.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We either have .enable_dma_transmission or .set_tx_tail_ptr in the HW
table callbacks, we can never have both so there is no need to check for
GMAC version.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the GMAC version for choosing if we need to use
dma_init or dma_init_{rx/tx}_chan callback, lets uniformize this and
always use the dma_init_{rx/tx}_chan callbacks.
While at it, fix the use of dma_init_chan callback, which shall be
called for as many channels as the max of rx/tx channels.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP and MMC modules base address can depend on the GMAC version. As this
is HW specific lets move this base address calculation to hwif.c. Also,
add an entry in the HW table so that we can specify the module offset.
This can later be extended to more modules, if deemed necessary.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introducion of callbacks check in hwif.h we only call the
callback if HW supports it so there is no longer need to check for GMAC
version.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on the GMAC version for choosing if we need to use
dma_{rx/tx}_mode or just dma_mode callback lets uniformize this and
always use the dma_{rx/tx}_mode callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop using if conditions depending on the GMAC version for clearing the
descriptor and use instead a helper implemented in the descriptor files.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stop using if conditions depending on the GMAC version for setting the
the descriptor skbuff address and use instead a helper implemented in
the descriptor files.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is cutting down performance. Once the timer is armed it should run
after the time expires for the first packet sent and not the last one.
After this change, running iperf, the performance gain is +/- 24%.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables OSP (Operate on Second Packet) for GMAC4. The feature
allows DMA to fetch second descriptor while its still processing the
first one.
Running iperf, the performance gain is +/- 38%.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the representor only report the SW (slow-path) traffic
counters.
Add packet/bytes reporting of the HW counters, which account for the
total amount of traffic that was handled by the vport, both slow and
fast (offloaded) paths. The newly exposed counters are named
vport_rx/tx_packets/bytes.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For VF->VF and uplink->VF rules, the TC core (cls_api) attempts
to offload the same flow multiple times into the driver, b/c we
registered to the egdev callback.
Use the flow cookie to ignore attempts to add such flows, we can't
reject them (return error), b/c this will fail the offload attempt,
so we ignore that. We indentify wrong stat/del calls using the flow
ingress/egress flags, here we do return error to the core.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, each representor netdev use their own hash table to keep
the mapping from TC flow (f->cookie) to the driver offloaded instance.
The table is the one which originally was added for offloading TC NIC
(not eswitch) rules.
This scheme breaks when the core TC code calls us to add the same flow
twice, (e.g under egdev use case) since we don't spot that and offload
a 2nd flow into the HW with the wrong source vport.
As a pre-step to solve that, we move to use a single table which keeps
all offloaded TC eswitch flows. The table is located at the eswitch
uplink representor object.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This is a refactoring step to be able and store the hash table which
keeps track of offloaded TC flows in a different location for NIC
vs e-switch rules.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When an e-switch TC rule is offloaded through the egdev (egress
device) mechanism, we treat this as egress, all other cases (NIC
and e-switch) are considred ingress.
This is preparation step that will allow us to identify "wrong"
stat/del offload calls made by the TC core on egdev based flows and
ignore them.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When the merged eswitch capability is supported, allow offloading rules
between VFs which belong to different PFs (and hence have different
eswitch affinity).
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patche to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJa/fLEAAoJEEg/ir3gV/o+7jUH/3n5/Uw1LLt3TfeKArx6i0F1
3G4U5B0ha03qiDqXprwhyQ3I6lgYmRBmjcxnqmvcqOAqO4/hSsjtTR+A/mgbEDhJ
YtdekFNEX+72h/N2GIpZwChIWSE3EcMPaLYnV8TwLUgh9YSust2sCLSBbJCjxOKc
j78M8ept/bXZwTm/iJhEjtmqw0xl91rl011chCAua0iEpH3wxteDARmKABFHMQxl
I3N/x/e/astgcSCNgpO4uDf9zEIRkNdzcHPzSMJ6C2Oo5W9XiZEekfw7WKj9nXfa
G+eGckkAyCOQ/r2lZ9nA0ZUvQ2X6JISvxgohuaCNwTgsz3acTxbLnQK4YWHzQCQ=
=iHi6
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
mlx5-updates-2018-05-17
mlx5 core dirver updates for both net-next and rdma-next branches.
From Christophe JAILLET, first three patches to use kvfree where needed.
From: Or Gerlitz <ogerlitz@mellanox.com>
Next six patches from Roi and Co adds support for merged
sriov e-switch which comes to serve cases where both PFs, VFs set
on them and both uplinks are to be used in single v-switch SW model.
When merged e-switch is supported, the per-port e-switch is logically
merged into one e-switch that spans both physical ports and all the VFs.
This model allows to offload TC eswitch rules between VFs belonging
to different PFs (and hence have different eswitch affinity), it also
sets the some of the foundations needed for uplink LAG support.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set a specific source e-switch when setting a rule that matches on the
ingress port.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The source e-switch owner allows a vport on one e-switch port be associated
with a rule defined on the second port e-switch.
The role of the source eswitch owner valid bit in the flow group is to
allow the firmware fail driver attempts to wild card the source eswitch
match field. If this bit is not set, the firmware ignores the source
eswitch owner field totally.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set a specific destination e-switch when setting a destination vport.
Signed-off-by: Rabie Loulou <rabiel@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The destination e-switch owner allows a rule in namespace of one e-switch
owner to point to a vport that is natively associated with another
e-switch owner.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When creating FTE, properly distinguish between destination being vport
or tir. The previous code just worked accidentally b/c of both dest being
in the same offset within a union.
Signed-off-by: Shahar Klein <shahark@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Those drivers build just fine with COMPILE_TEST, so make that possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Freescale FEC driver builds fine with COMPILE_TEST, so make that
possible.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the TI drivers build just fine with COMPILE_TEST, cpmac (AR7) is
the exception because it uses a header file from
arch/mips/include/asm/mach-ar7/ar7.h and keystone netcp which requires
help from drivers/soc/ti/ for queue management helpers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.
This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.
Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32
HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.59 0.00 32.93 0.00 0.00 43.07 0.00 0.00 23.42
HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.70 0.00 31.70 0.00 0.00 25.68 0.00 0.00 41.92
HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.86 0.00 24.14 0.00 0.00 6.59 0.00 0.00 68.41
HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.87 0.00 23.75 0.00 0.00 6.19 0.00 0.00 69.19
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2018-05-17
This series contains updates to ixgbe, ixgbevf and ice drivers.
Cathy Zhou resolves sparse warnings by using the force attribute.
Mauro S M Rodrigues fixes a bug where IRQs were not freed if a PCI error
recovery system opts to remove the device which causes
ixgbe_io_error_detected() to return PCI_ERS_RESULT_DISCONNECT before
calling ixgbe_close_suspend() which results in IRQs not freed and
crashing when the remove handler calls pci_disable_device(). Resolved
this by calling ixgbe_close_suspend() before evaluating the PCI channel
state.
Pavel Tatashin releases the rtnl_lock during the call to
ixgbe_close_suspend() to allow scaling if device_shutdown() is
multi-threaded.
Emil modifies ixgbe to not validate the MAC address during a reset,
unless the MAC was set on the host so that the VF will get a new MAC
address every time it reloads. Also updates ixgbevf to set
hw->mac.perm_addr in order to retain the custom MAC on a reset.
Anirudh updates the ice NVM read/erase/update AQ commands to align with
the latest specification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't store repr pointer to reprs array until the representor is
successfully created. This avoids message about "representor
destruction" even when it was never created. Also it cleans-up the flow.
Also, check return value after port alloc.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent flood of RX error prints during heavy traffic with weak signal
in link by checking net_ratelimit() before using netdev_err().
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: small rework, commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove special stop/start handling from the set_mac_address callback.
All this special care is not needed, and can be removed. It also
simplifies the up/down status in the driver and helps avoiding possible
link status mismatch issues.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid repeating the check for free aggregated descriptors when it
already failed at the beginning of the function.
Signed-off-by: Yan Markman <ymarkman@marvell.com>
[Antoine: commit message]
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PPv2 driver to implement phylink helpers, and use phylink in
DT mode. The other mode supported is ACPI, which will need further work
in order to be entirely compatible with phylink.
The MAC and GoP configuration functions were completely moved to fit
into the phylink helpers. When a PHY is always present between the MAC
and the physical port, phylink only is used, but when this is not the
case (the MAC directly is connected to the physical port) the link IRQ
is used to detect changes in the link state and call phylink_mac_change.
The ACPI mode do not uses phylink as of now, and the changes shouldn't
impact its use.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to align the ethtool functions to ops definitions. This
patch does not change in any way the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.
I also merged wireless-drivers due to an iwlwifi patch dependency.
Major changes:
iwlwifi
* implement Traffic Condition Monitor and use it for scan, BT coex and
to detect when the AP doesn't support UAPSD properly
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload
qtnfmac
* DFS offload support
rsi
* roaming enhancements
* increase max supported aggregation subframes
* don't advertise 5 GHz support if the device doesn't support it
brcmfmac
* add support for BCM4366E chipset
* add support for bcm43364 wireless chipset
ath10k
* enable temperature reads for QCA6174 and QCA9377
* add firmware memory dump support for QCA9984
* continue adding WCN3990 support via SNOC bus
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJa/TreAAoJEG4XJFUm622boV0IAI/tTu3obIdhdlnZJsjat/wH
tmQX2rZl0g7kbthVU+WqPA1KgvK/HEX1SUIP0leARl6FDqxrBzE1G4P1fOY3JIaZ
+T3UG9LgFM3hoXtJ1VRdvi8rTBVU67TTOrQCVD7AapGWfQwn6AXfy4ARUEqBjkrA
SxDemdAwIks3miMU3EnsRlzLaI56R7l1mk0Xr30tM5Coq721AcWE6FBz6lqmFnTC
3vdDzpMRIiTt5zLICJZYgAB3akiaJEqHnIAv+y0sbXG1gHDhKcfEH674SM6FCB2N
3TP7EpzzxH/FYB0i+zOFg6wnAqUngLLnwkG/ciniVi75feb+gbaKqWHT8FNfx04=
=rF/V
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-05-17' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.
I also merged wireless-drivers due to an iwlwifi patch dependency.
Major changes:
iwlwifi
* implement Traffic Condition Monitor and use it for scan, BT coex and
to detect when the AP doesn't support UAPSD properly
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload
qtnfmac
* DFS offload support
rsi
* roaming enhancements
* increase max supported aggregation subframes
* don't advertise 5 GHz support if the device doesn't support it
brcmfmac
* add support for BCM4366E chipset
* add support for bcm43364 wireless chipset
ath10k
* enable temperature reads for QCA6174 and QCA9377
* add firmware memory dump support for QCA9984
* continue adding WCN3990 support via SNOC bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/timers/timers-howto.txt,
replace msleep(1) with usleep_range().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an new common helper to avoid redundancy.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The early versions of am33xx devices, related to ES1.0 SoC revision
have errata limiting mq support. That's the same errata as
commit 7da1160002 ("drivers: net: cpsw: add am335x errata workarround for
interrutps")
AM33xx Errata [1] Advisory 1.0.9
http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
After additional investigation were found that drivers w/a is
propagated on all AM33xx SoCs and on DM814x. But the errata exists
only for ES1.0 of AM33xx family, limiting mq support for revisions
after ES1.0. So, disable mq support only for related SoCs and use
separate polls for revisions allowing mq.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move initialization of statistics buffers from ibmvnic_init function
into ibmvnic_probe. In the current state, ibmvnic_init will be called
again during a device reset, resulting in the allocation of new
buffers without freeing the old ones.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sridhar Samudrala