This patch addresses two issues. First it adds the correct bit definitions
for the SECTXSTAT and SECRXSTAT registers. Then it makes use of those
definitions to test for if IPsec has been disabled on the part and if so we
do not enable it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reported-by: Andre Tomt <andre@tomt.net>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two issues. First we add an early test for the Tx and Rx
security block ready bits. By doing this we can avoid the need for waits or
loopback in the event that the security block is already flushed out.
Secondly we fix the boolean logic that was testing for the Tx OR Rx ready
bits being set and change it so that we only exit if the Tx AND Rx ready
bits are both set.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch moves the IPsec init function in ixgbe_sw_init. This way it is a
bit more consistent with the placement of similar initialization functions
and is placed before the reset_hw call which should allow us to clean up
any link issues that may be introduced by the fact that we force the link
up if somehow the device had IPsec still enabled before the driver was
loaded.
In addition to the function move it is necessary to change the assignment
of netdev->features. The easiest way to do this is to just test for the
existence of adapter->ipsec and if it is present we set the feature bits.
Fixes: 49a94d74d9 ("ixgbe: add ipsec engine start and stop routines")
Reported-by: Andre Tomt <andre@tomt.net>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no point in adding code if CONFIG_XFRM is defined that we won't
use unless CONFIG_XFRM_OFFLOAD is defined. So instead of leaving this code
floating around I am replacing the ifdef with what I believe is the correct
one so that we only include the code and variables if they will actually be
used.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we were enabling macvlan interfaces we weren't correctly configuring
things until ixgbe_setup_tc was called a second time either by tweaking the
number of queues or increasing the macvlan count past 15.
The issue came down to the fact that num_rx_pools is not populated until
after the queues and interrupts are reinitialized.
Instead of trying to set it sooner we can just move the call to setup at
least 1 traffic class to the SR-IOV/VMDq setup function so that we just set
it for this one case. We already had a spot that was configuring the queues
for TC 0 in the code here anyway so it makes sense to also set the number
of TCs here as well.
Fixes: 49cfbeb7a9 ("ixgbe: Fix handling of macvlan Tx offload")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
1) Fix several bpfilter/UMH bugs, in particular make the UMH build not
depend upon X86 specific Kconfig symbols. From Alexei Starovoitov.
2) Fix handling of modified context pointer in bpf verifier, from
Daniel Borkmann.
3) Kill regression in ifdown/ifup sequences for hv_netvsc driver, from
Dexuan Cui.
4) When the bonding primary member name changes, we have to re-evaluate
the bond->force_primary setting, from Xiangning Yu.
5) Eliminate possible padding beyone end of SKB in cdc_ncm driver, from
Bjørn Mork.
6) RX queue length reported for UDP sockets in procfs and socket diag
are inaccurate, from Paolo Abeni.
7) Fix br_fdb_find_port() locking, from Petr Machata.
8) Limit sk_rcvlowat values properly in TCP, from Soheil Hassas
Yeganeh.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (23 commits)
tcp: limit sk_rcvlowat by the maximum receive buffer
net: phy: dp83822: use BMCR_ANENABLE instead of BMSR_ANEGCAPABLE for DP83620
socket: close race condition between sock_close() and sockfs_setattr()
net: bridge: Fix locking in br_fdb_find_port()
udp: fix rx queue len reported by diag and proc interface
cdc_ncm: avoid padding beyond end of skb
net/sched: act_simple: fix parsing of TCA_DEF_DATA
net: fddi: fix a possible null-ptr-deref
net: aquantia: fix unsigned numvecs comparison with less than zero
net: stmmac: fix build failure due to missing COMMON_CLK dependency
bpfilter: fix race in pipe access
bpf, xdp: fix crash in xdp_umem_unaccount_pages
xsk: Fix umem fill/completion queue mmap on 32-bit
tools/bpf: fix selftest get_cgroup_id_user
bpfilter: fix OUTPUT_FORMAT
umh: fix race condition
net: mscc: ocelot: Fix uninitialized error in ocelot_netdevice_event()
bonding: re-evaluate force_primary when the primary slave name changes
ip_tunnel: Fix name string concatenate in __ip_tunnel_create()
hv_netvsc: Fix a network regression after ifdown/ifup
...
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
DP83620 register set is compatible with the DP83848, but it also supports
100base-FX. When the hardware is configured such as that fiber mode is
enabled, autonegotiation is not possible.
The chip, however, doesn't expose this information via BMSR_ANEGCAPABLE.
Instead, this bit is always set high, even if the particular hardware
configuration makes it so that auto negotiation is not possible [1]. Under
these circumstances, the phy subsystem keeps trying for autonegotiation to
happen, without success.
Hereby, we inspect BMCR_ANENABLE bit after genphy_config_init, which on
reset is set to 0 when auto negotiation is disabled, and so we use this
value instead of BMSR_ANEGCAPABLE.
[1] https://e2e.ti.com/support/interface/ethernet/f/903/p/697165/2571170
Signed-off-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bp->SharedMemAddr is set to NULL while bp->SharedMemSize lesser-or-equal 0,
then memset will trigger null-ptr-deref.
fix it by replacing pci_alloc_consistent with dma_zalloc_coherent.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Colin Ian King <colin.king@canonical.com>
This was originally mistakenly submitted to net-next. Resubmitting to net.
The comparison of numvecs < 0 is always false because numvecs is a u32
and hence the error return from a failed call to pci_alloc_irq_vectores
is never detected. Fix this by using the signed int ret to handle the
error return and assign numvecs to err.
Detected by CoverityScan, CID#1468650 ("Unsigned compared against 0")
Fixes: a09bd81b54 ("net: aquantia: Limit number of vectors to actually allocated irqs")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCWxoCWAAKCRCAXGG7T9hj
vvDrAQCR6Js8PWjU8HnaYV/AKYGJ/JANLUSKhK/piel+ed7c7AD/T2XV7m0WI+Rb
p+dwBd7NLoVokF4SQHvvWgQJLSW7qAA=
=BnsW
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"This contains some minor code cleanups (fixing return types of
functions), some fixes for Linux running as Xen PVH guest, and adding
of a new guest resource mapping feature for Xen tools"
* tag 'for-linus-4.18-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/PVH: Make GDT selectors PVH-specific
xen/PVH: Set up GS segment for stack canary
xen/store: do not store local values in xen_start_info
xen-netfront: fix xennet_start_xmit()'s return type
xen/privcmd: add IOCTL_PRIVCMD_MMAP_RESOURCE
xen: Change return type to vm_fault_t
This patch fix the build failure on m68k;
drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.o: In function `ipq806x_gmac_probe':
dwmac-ipq806x.c:(.text+0xda): undefined reference to `clk_set_rate'
drivers/net/ethernet/stmicro/stmmac/dwmac-rk.o: In function `rk_gmac_probe':
dwmac-rk.c:(.text+0x1e58): undefined reference to `clk_set_rate'
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.o: In function `stid127_fix_retime_src':
dwmac-sti.c:(.text+0xd8): undefined reference to `clk_set_rate'
dwmac-sti.c:(.text+0x114): undefined reference to `clk_set_rate'
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.o:dwmac-sti.c:(.text+0x12c): more undefined references to `clk_set_rate' follow
Lots of stmmac platform drivers need COMMON_CLK in their Kconfig depends.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With gcc-4.1.2:
drivers/net/ethernet/mscc/ocelot.c: In function ‘ocelot_netdevice_event’:
drivers/net/ethernet/mscc/ocelot.c:1129: warning: ‘ret’ may be used uninitialized in this function
If the list iterated over by netdev_for_each_lower_dev() is empty, ret
is never initialized, and converted into a notifier return value.
Fix this by preinitializing ret to zero.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a timing issue under active-standy mode, when bond_enslave() is
called, bond->params.primary might not be initialized yet.
Any time the primary slave string changes, bond->force_primary should be
set to true to make sure the primary becomes the active slave.
Signed-off-by: Xiangning Yu <yuxiangning@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently people reported the NIC stops working after
"ifdown eth0; ifup eth0". It turns out in this case the TX queues are not
enabled, after the refactoring of the common detach logic: when the NIC
has sub-channels, usually we enable all the TX queues after all
sub-channels are set up: see rndis_set_subchannel() ->
netif_device_attach(), but in the case of "ifdown eth0; ifup eth0" where
the number of channels doesn't change, we also must make sure the TX queues
are enabled. The patch fixes the regression.
Fixes: 7b2ee50c0c ("hv_netvsc: common detach logic")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tun, tap, virtio, packet and uml vector all use struct virtio_net_hdr
to communicate packet metadata to userspace.
For skbuffs with vlan, the first two return the packet as it may have
existed on the wire, inserting the VLAN tag in the user buffer. Then
virtio_net_hdr.csum_start needs to be adjusted by VLAN_HLEN bytes.
Commit f09e2249c4 ("macvtap: restore vlan header on user read")
added this feature to macvtap. Commit 3ce9b20f19 ("macvtap: Fix
csum_start when VLAN tags are present") then fixed up csum_start.
Virtio, packet and uml do not insert the vlan header in the user
buffer.
When introducing virtio_net_hdr_from_skb to deduplicate filling in
the virtio_net_hdr, the variant from macvtap which adds VLAN_HLEN was
applied uniformly, breaking csum offset for packets with vlan on
virtio and packet.
Make insertion of VLAN_HLEN optional. Convert the callers to pass it
when needed.
Fixes: e858fae2b0 ("virtio_net: use common code for virtio_net_hdr and skb GSO conversion")
Fixes: 1276f24eee ("packet: use common code for virtio_net_hdr and skb GSO conversion")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been a quiet cycle for RDMA, the big bulk is the usual smallish
driver updates and bug fixes. About four new uAPI related things. Not as much
Szykaller patches this time, the bugs it finds are getting harder to fix.
- More work cleaning up the RDMA CM code
- Usual driver bug fixes and cleanups for qedr, qib, hfi1, hns, i40iw, iw_cxgb4, mlx5, rxe
- Driver specific resource tracking and reporting via netlink
- Continued work for name space support from Parav
- MPLS support for the verbs flow steering uAPI
- A few tricky IPoIB fixes improving robustness
- HFI1 driver support for the '16B' management packet format
- Some auditing to not print kernel pointers via %llx or similar
- Mark the entire 'UCM' user-space interface as BROKEN with the intent to remove it
entirely. The user space side of this was long ago replaced with RDMA-CM and
syzkaller is finding bugs in the residual UCM interface nobody wishes to fix because
nobody uses it.
- Purge more bogus BUG_ON's from Leon
- 'flow counters' verbs uAPI
- T10 fixups for iser/isert, these are Acked by Martin but going through the RDMA
tree due to dependencies
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=Mb8m
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"This has been a quiet cycle for RDMA, the big bulk is the usual
smallish driver updates and bug fixes. About four new uAPI related
things. Not as much Szykaller patches this time, the bugs it finds are
getting harder to fix.
Summary:
- More work cleaning up the RDMA CM code
- Usual driver bug fixes and cleanups for qedr, qib, hfi1, hns,
i40iw, iw_cxgb4, mlx5, rxe
- Driver specific resource tracking and reporting via netlink
- Continued work for name space support from Parav
- MPLS support for the verbs flow steering uAPI
- A few tricky IPoIB fixes improving robustness
- HFI1 driver support for the '16B' management packet format
- Some auditing to not print kernel pointers via %llx or similar
- Mark the entire 'UCM' user-space interface as BROKEN with the
intent to remove it entirely. The user space side of this was long
ago replaced with RDMA-CM and syzkaller is finding bugs in the
residual UCM interface nobody wishes to fix because nobody uses it.
- Purge more bogus BUG_ON's from Leon
- 'flow counters' verbs uAPI
- T10 fixups for iser/isert, these are Acked by Martin but going
through the RDMA tree due to dependencies"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (138 commits)
RDMA/mlx5: Update SPDX tags to show proper license
RDMA/restrack: Change SPDX tag to properly reflect license
IB/hfi1: Fix comment on default hdr entry size
IB/hfi1: Rename exp_lock to exp_mutex
IB/hfi1: Add bypass register defines and replace blind constants
IB/hfi1: Remove unused variable
IB/hfi1: Ensure VL index is within bounds
IB/hfi1: Fix user context tail allocation for DMA_RTAIL
IB/hns: Use zeroing memory allocator instead of allocator/memset
infiniband: fix a possible use-after-free bug
iw_cxgb4: add INFINIBAND_ADDR_TRANS dependency
IB/isert: use T10-PI check mask definitions from core layer
IB/iser: use T10-PI check mask definitions from core layer
RDMA/core: introduce check masks for T10-PI offload
IB/isert: fix T10-pi check mask setting
IB/mlx5: Add counters read support
IB/mlx5: Add flow counters read support
IB/mlx5: Add flow counters binding support
IB/mlx5: Add counters create and destroy support
IB/uverbs: Add support for flow counters
...
-----BEGIN PGP SIGNATURE-----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=aFAi
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- unify AER decoding for native and ACPI CPER sources (Alexandru
Gagniuc)
- add TLP header info to AER tracepoint (Thomas Tai)
- add generic pcie_wait_for_link() interface (Oza Pawandeep)
- handle AER ERR_FATAL by removing and re-enumerating devices, as
Downstream Port Containment does (Oza Pawandeep)
- factor out common code between AER and DPC recovery (Oza Pawandeep)
- stop triggering DPC for ERR_NONFATAL errors (Oza Pawandeep)
- share ERR_FATAL recovery path between AER and DPC (Oza Pawandeep)
- disable ASPM L1.2 substate if we don't have LTR (Bjorn Helgaas)
- respect platform ownership of LTR (Bjorn Helgaas)
- clear interrupt status in top half to avoid interrupt storm (Oza
Pawandeep)
- neaten pci=earlydump output (Andy Shevchenko)
- avoid errors when extended config space inaccessible (Gilles Buloz)
- prevent sysfs disable of device while driver attached (Christoph
Hellwig)
- use core interface to report PCIe link properties in bnx2x, bnxt_en,
cxgb4, ixgbe (Bjorn Helgaas)
- remove unused pcie_get_minimum_link() (Bjorn Helgaas)
- fix use-before-set error in ibmphp (Dan Carpenter)
- fix pciehp timeouts caused by Command Completed errata (Bjorn
Helgaas)
- fix refcounting in pnv_php hotplug (Julia Lawall)
- clear pciehp Presence Detect and Data Link Layer Status Changed on
resume so we don't miss hotplug events (Mika Westerberg)
- only request pciehp control if we support it, so platform can use
ACPI hotplug otherwise (Mika Westerberg)
- convert SHPC to be builtin only (Mika Westerberg)
- request SHPC control via _OSC if we support it (Mika Westerberg)
- simplify SHPC handoff from firmware (Mika Westerberg)
- fix an SHPC quirk that mistakenly included *all* AMD bridges as well
as devices from any vendor with device ID 0x7458 (Bjorn Helgaas)
- assign a bus number even to non-native hotplug bridges to leave
space for acpiphp additions, to fix a common Thunderbolt xHCI
hot-add failure (Mika Westerberg)
- keep acpiphp from scanning native hotplug bridges, to fix common
Thunderbolt hot-add failures (Mika Westerberg)
- improve "partially hidden behind bridge" messages from core (Mika
Westerberg)
- add macros for PCIe Link Control 2 register (Frederick Lawler)
- replace IB/hfi1 custom macros with PCI core versions (Frederick
Lawler)
- remove dead microblaze and xtensa code (Bjorn Helgaas)
- use dev_printk() when possible in xtensa and mips (Bjorn Helgaas)
- remove unused pcie_port_acpi_setup() and portdrv_acpi.c (Bjorn
Helgaas)
- add managed interface to get PCI host bridge resources from OF (Jan
Kiszka)
- add support for unbinding generic PCI host controller (Jan Kiszka)
- fix memory leaks when unbinding generic PCI host controller (Jan
Kiszka)
- request legacy VGA framebuffer only for VGA devices to avoid false
device conflicts (Bjorn Helgaas)
- turn on PCI_COMMAND_IO & PCI_COMMAND_MEMORY in pci_enable_device()
like everybody else, not in pcibios_fixup_bus() (Bjorn Helgaas)
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
- enable register clock for Armada 7K/8K (Gregory CLEMENT)
- reduce Keystone "link already up" log level (Fabio Estevam)
- move private DT functions to drivers/pci/ (Rob Herring)
- factor out dwc CONFIG_PCI Kconfig dependencies (Rob Herring)
- add DesignWare support to the endpoint test driver (Gustavo
Pimentel)
- add DesignWare support for endpoint mode (Gustavo Pimentel)
- use devm_ioremap_resource() instead of devm_ioremap() in dra7xx and
artpec6 (Gustavo Pimentel)
- fix Qualcomm bitwise NOT issue (Dan Carpenter)
- add Qualcomm runtime PM support (Srinivas Kandagatla)
- fix DesignWare enumeration below bridges (Koen Vandeputte)
- use usleep() instead of mdelay() in endpoint test (Jia-Ju Bai)
- add configfs entries for pci_epf_driver device IDs (Kishon Vijay
Abraham I)
- clean up pci_endpoint_test driver (Gustavo Pimentel)
- update Layerscape maintainer email addresses (Minghuan Lian)
- add COMPILE_TEST to improve build test coverage (Rob Herring)
- fix Hyper-V bus registration failure caused by domain/serial number
confusion (Sridhar Pitchai)
- improve Hyper-V refcounting and coding style (Stephen Hemminger)
- avoid potential Hyper-V hang waiting for a response that will never
come (Dexuan Cui)
- implement Mediatek chained IRQ handling (Honghui Zhang)
- fix vendor ID & class type for Mediatek MT7622 (Honghui Zhang)
- add Mobiveil PCIe host controller driver (Subrahmanya Lingappa)
- add Mobiveil MSI support (Subrahmanya Lingappa)
- clean up clocks, MSI, IRQ mappings in R-Car probe failure paths
(Marek Vasut)
- poll more frequently (5us vs 5ms) while waiting for R-Car data link
active (Marek Vasut)
- use generic OF parsing interface in R-Car (Vladimir Zapolskiy)
- add R-Car V3H (R8A77980) "compatible" string (Sergei Shtylyov)
- add R-Car gen3 PHY support (Sergei Shtylyov)
- improve R-Car PHYRDY polling (Sergei Shtylyov)
- clean up R-Car macros (Marek Vasut)
- use runtime PM for R-Car controller clock (Dien Pham)
- update arm64 defconfig for Rockchip (Shawn Lin)
- refactor Rockchip code to facilitate both root port and endpoint
mode (Shawn Lin)
- add Rockchip endpoint mode driver (Shawn Lin)
- support VMD "membar shadow" feature (Jon Derrick)
- support VMD bus number offsets (Jon Derrick)
- add VMD "no AER source ID" quirk for more device IDs (Jon Derrick)
- remove unnecessary host controller CONFIG_PCIEPORTBUS Kconfig
selections (Bjorn Helgaas)
- clean up quirks.c organization and whitespace (Bjorn Helgaas)
* tag 'pci-v4.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (144 commits)
PCI/AER: Replace struct pcie_device with pci_dev
PCI/AER: Remove unused parameters
PCI: qcom: Include gpio/consumer.h
PCI: Improve "partially hidden behind bridge" log message
PCI: Improve pci_scan_bridge() and pci_scan_bridge_extend() doc
PCI: Move resource distribution for single bridge outside loop
PCI: Account for all bridges on bus when distributing bus numbers
ACPI / hotplug / PCI: Drop unnecessary parentheses
ACPI / hotplug / PCI: Mark stale PCI devices disconnected
ACPI / hotplug / PCI: Don't scan bridges managed by native hotplug
PCI: hotplug: Add hotplug_is_native()
PCI: shpchp: Add shpchp_is_native()
PCI: shpchp: Fix AMD POGO identification
PCI: mobiveil: Add MSI support
PCI: mobiveil: Add Mobiveil PCIe Host Bridge IP driver
PCI/AER: Decode Error Source Requester ID
PCI/AER: Remove aer_recover_work_func() forward declaration
PCI/DPC: Use the generic pcie_do_fatal_recovery() path
PCI/AER: Pass service type to pcie_do_fatal_recovery()
PCI/DPC: Disable ERR_NONFATAL handling by DPC
...
Pull networking updates from David Miller:
1) Add Maglev hashing scheduler to IPVS, from Inju Song.
2) Lots of new TC subsystem tests from Roman Mashak.
3) Add TCP zero copy receive and fix delayed acks and autotuning with
SO_RCVLOWAT, from Eric Dumazet.
4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard
Brouer.
5) Add ttl inherit support to vxlan, from Hangbin Liu.
6) Properly separate ipv6 routes into their logically independant
components. fib6_info for the routing table, and fib6_nh for sets of
nexthops, which thus can be shared. From David Ahern.
7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP
messages from XDP programs. From Nikita V. Shirokov.
8) Lots of long overdue cleanups to the r8169 driver, from Heiner
Kallweit.
9) Add BTF ("BPF Type Format"), from Martin KaFai Lau.
10) Add traffic condition monitoring to iwlwifi, from Luca Coelho.
11) Plumb extack down into fib_rules, from Roopa Prabhu.
12) Add Flower classifier offload support to igb, from Vinicius Costa
Gomes.
13) Add UDP GSO support, from Willem de Bruijn.
14) Add documentation for eBPF helpers, from Quentin Monnet.
15) Add TLS tx offload to mlx5, from Ilya Lesokhin.
16) Allow applications to be given the number of bytes available to read
on a socket via a control message returned from recvmsg(), from
Soheil Hassas Yeganeh.
17) Add x86_32 eBPF JIT compiler, from Wang YanQing.
18) Add AF_XDP sockets, with zerocopy support infrastructure as well.
From Björn Töpel.
19) Remove indirect load support from all of the BPF JITs and handle
these operations in the verifier by translating them into native BPF
instead. From Daniel Borkmann.
20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha.
21) Allow XDP programs to do lookups in the main kernel routing tables
for forwarding. From David Ahern.
22) Allow drivers to store hardware state into an ELF section of kernel
dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy.
23) Various RACK and loss detection improvements in TCP, from Yuchung
Cheng.
24) Add TCP SACK compression, from Eric Dumazet.
25) Add User Mode Helper support and basic bpfilter infrastructure, from
Alexei Starovoitov.
26) Support ports and protocol values in RTM_GETROUTE, from Roopa
Prabhu.
27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard
Brouer.
28) Add lots of forwarding selftests, from Petr Machata.
29) Add generic network device failover driver, from Sridhar Samudrala.
* ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits)
strparser: Add __strp_unpause and use it in ktls.
rxrpc: Fix terminal retransmission connection ID to include the channel
net: hns3: Optimize PF CMDQ interrupt switching process
net: hns3: Fix for VF mailbox receiving unknown message
net: hns3: Fix for VF mailbox cannot receiving PF response
bnx2x: use the right constant
Revert "net: sched: cls: Fix offloading when ingress dev is vxlan"
net: dsa: b53: Fix for brcm tag issue in Cygnus SoC
enic: fix UDP rss bits
netdev-FAQ: clarify DaveM's position for stable backports
rtnetlink: validate attributes in do_setlink()
mlxsw: Add extack messages for port_{un, }split failures
netdevsim: Add extack error message for devlink reload
devlink: Add extack to reload and port_{un, }split operations
net: metrics: add proper netlink validation
ipmr: fix error path when ipmr_new_table fails
ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds
net: hns3: remove unused hclgevf_cfg_func_mta_filter
netfilter: provide udp*_lib_lookup for nf_tproxy
qed*: Utilize FW 8.37.2.0
...
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=/3L8
-----END PGP SIGNATURE-----
Merge tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull overflow updates from Kees Cook:
"This adds the new overflow checking helpers and adds them to the
2-factor argument allocators. And this adds the saturating size
helpers and does a treewide replacement for the struct_size() usage.
Additionally this adds the overflow testing modules to make sure
everything works.
I'm still working on the treewide replacements for allocators with
"simple" multiplied arguments:
*alloc(a * b, ...) -> *alloc_array(a, b, ...)
and
*zalloc(a * b, ...) -> *calloc(a, b, ...)
as well as the more complex cases, but that's separable from this
portion of the series. I expect to have the rest sent before -rc1
closes; there are a lot of messy cases to clean up.
Summary:
- Introduce arithmetic overflow test helper functions (Rasmus)
- Use overflow helpers in 2-factor allocators (Kees, Rasmus)
- Introduce overflow test module (Rasmus, Kees)
- Introduce saturating size helper functions (Matthew, Kees)
- Treewide use of struct_size() for allocators (Kees)"
* tag 'overflow-v4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
treewide: Use struct_size() for devm_kmalloc() and friends
treewide: Use struct_size() for vmalloc()-family
treewide: Use struct_size() for kmalloc()-family
device: Use overflow helpers for devm_kmalloc()
mm: Use overflow helpers in kvmalloc()
mm: Use overflow helpers in kmalloc_array*()
test_overflow: Add memory allocation overflow tests
overflow.h: Add allocation size calculation helpers
test_overflow: Report test failures
test_overflow: macrofy some more, do more tests for free
lib: add runtime test of check_*_overflow functions
compiler.h: enable builtin overflow checkers and add fallback code
- add generic enable function for simple SR-IOV hardware (Alexander
Duyck)
- use generic SR-IOV enable for ena, nvme (Alexander Duyck)
- add ACS quirk for Intel 7th & 8th Gen mobile (Alex Williamson)
- add ACS quirk for Intel 300 series (Mika Westerberg)
* pci/virtualization:
PCI/IOV: Allow PF drivers to limit total_VFs to 0
PCI: Add "pci=noats" boot parameter
PCI: Add ACS quirk for Intel 300 series
PCI: Add ACS quirk for Intel 7th & 8th Gen mobile
nvme-pci: Use pci_sriov_configure_simple() to enable VFs
net: ena: Use pci_sriov_configure_simple() to enable VFs
PCI/IOV: Add pci-pf-stub driver for PFs that only enable VFs
PCI/IOV: Add pci_sriov_configure_simple()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kmalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, entry, count), GFP_KERNEL);
This patch makes the changes for kmalloc()-family (and kvmalloc()-family)
uses. It was done via automatic conversion with manual review for the
"CHECKME" non-standard cases noted below, using the following Coccinelle
script:
// pkey_cache = kmalloc(sizeof *pkey_cache + tprops->pkey_tbl_len *
// sizeof *pkey_cache->table, GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(*VAR->ELEMENT), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// mr = kzalloc(sizeof(*mr) + m * sizeof(mr->map[0]), GFP_KERNEL);
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
identifier VAR, ELEMENT;
expression COUNT;
@@
- alloc(sizeof(*VAR) + COUNT * sizeof(VAR->ELEMENT[0]), GFP)
+ alloc(struct_size(VAR, ELEMENT, COUNT), GFP)
// Same pattern, but can't trivially locate the trailing element name,
// or variable name.
@@
identifier alloc =~ "kmalloc|kzalloc|kvmalloc|kvzalloc";
expression GFP;
expression SOMETHING, COUNT, ELEMENT;
@@
- alloc(sizeof(SOMETHING) + COUNT * sizeof(ELEMENT), GFP)
+ alloc(CHECKME_struct_size(&SOMETHING, ELEMENT, COUNT), GFP)
Signed-off-by: Kees Cook <keescook@chromium.org>
When the PF frequently switches the CMDQ interrupt, if the CMDQ_SRC is
not cleared before the hardware interrupt is generated, the new interrupt
will not be reported.
This patch optimizes this problem by clearing CMDQ_SRC and RESET_STS
before enabling interrupt and syncing pending IRQ handlers after disabling
interrupt.
Fixes: 466b0c0039 ("net: hns3: Add support for misc interrupt")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the firmware updates the crq's tail pointer, if the VF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is empty before reading the
message.
Fixes: b11a0bb231 ("net: hns3: Add mailbox support to VF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VF frequently switches the CMDQ interrupt, if the CMDQ_SRC is not
cleared, the VF will not receive the new PF response after the interrupt
is re-enabled, the corresponding log is as follows:
[ 317.482222] hns3 0000:00:03.0: VF could not get mbx resp(=0) from PF
in 500 tries
[ 317.483137] hns3 0000:00:03.0: VF request to get tqp info from PF
failed -5
This patch fixes this problem by clearing CMDQ_SRC before enabling
interrupt and syncing pending IRQ handlers after disabling interrupt.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nearby code that also tests port suggests that the P0 constant should be
used when port is zero.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,e1;
@@
* e ? e1 : e1
// </smpl>
Fixes: 6c3218c6f7 ("bnx2x: Adjust ETS to 578xx")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 1160603960 ("net: dsa: b53: Support prepended Broadcom tags")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reported-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 48398b6e70 ("enic: set UDP rss flag") driver needed to set a
single bit to enable UDP rss. This is changed to two bit. One for UDP
IPv4 and other bit for UDP IPv6. The hardware which supports this is not
released yet. When released, driver should set 2 bit to enable UDP rss for
both IPv4 and IPv6.
Also add spinlock around vnic_dev_capable_rss_hash_type().
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to be
able to understand the firmware code better. There's also a user for a
new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZAg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykbiACgu/2qqou1iV4GxOkvrj5wfsHD+lYAoNPNNDHu
Qf3CCEKbxogF6YowDiAH
=Dsqq
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the driver core patchset for 4.18-rc1.
The large chunk of these are firmware core documentation and api
updates. Nothing major there, just better descriptions for others to
be able to understand the firmware code better. There's also a user
for a new firmware api call.
Other than that, there are some minor updates for debugfs, kernfs, and
the driver core itself.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
driver core: hold dev's parent lock when needed
driver-core: return EINVAL error instead of BUG_ON()
driver core: add __printf verification to device_create_groups_vargs
mm: memory_hotplug: use put_device() if device_register fail
base: core: fix typo 'can by' to 'can be'
debugfs: inode: debugfs_create_dir uses mode permission from parent
debugfs: Re-use kstrtobool_from_user()
Documentation: clarify firmware_class provenance and why we can't rename the module
Documentation: remove stale firmware API reference
Documentation: fix few typos and clarifications for the firmware loader
ath10k: re-enable the firmware fallback mechanism for testmode
ath10k: use firmware_request_nowarn() to load firmware
firmware: add firmware_request_nowarn() - load firmware without warnings
firmware_loader: make firmware_fallback_sysfs() print more useful
firmware_loader: move kconfig FW_LOADER entries to its own file
firmware_loader: replace ---help--- with help
firmware_loader: enhance Kconfig documentation over FW_LOADER
firmware_loader: document firmware_sysfs_fallback()
firmware: rename fw_sysfs_fallback to firmware_fallback_sysfs()
firmware: use () to terminate kernel-doc function names
...
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-06-05
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a new BPF hook for sendmsg similar to existing hooks for bind and
connect: "This allows to override source IP (including the case when it's
set via cmsg(3)) and destination IP:port for unconnected UDP (slow path).
TCP and connected UDP (fast path) are not affected. This makes UDP support
complete, that is, connected UDP is handled by connect hooks, unconnected
by sendmsg ones.", from Andrey.
2) Rework of the AF_XDP API to allow extending it in future for type writer
model if necessary. In this mode a memory window is passed to hardware
and multiple frames might be filled into that window instead of just one
that is the case in the current fixed frame-size model. With the new
changes made this can be supported without having to add a new descriptor
format. Also, core bits for the zero-copy support for AF_XDP have been
merged as agreed upon, where i40e bits will be routed via Jeff later on.
Various improvements to documentation and sample programs included as
well, all from Björn and Magnus.
3) Given BPF's flexibility, a new program type has been added to implement
infrared decoders. Quote: "The kernel IR decoders support the most
widely used IR protocols, but there are many protocols which are not
supported. [...] There is a 'long tail' of unsupported IR protocols,
for which lircd is need to decode the IR. IR encoding is done in such
a way that some simple circuit can decode it; therefore, BPF is ideal.
[...] user-space can define a decoder in BPF, attach it to the rc
device through the lirc chardev.", from Sean.
4) Several improvements and fixes to BPF core, among others, dumping map
and prog IDs into fdinfo which is a straight forward way to correlate
BPF objects used by applications, removing an indirect call and therefore
retpoline in all map lookup/update/delete calls by invoking the callback
directly for 64 bit archs, adding a new bpf_skb_cgroup_id() BPF helper
for tc BPF programs to have an efficient way of looking up cgroup v2 id
for policy or other use cases. Fixes to make sure we zero tunnel/xfrm
state that hasn't been filled, to allow context access wrt pt_regs in
32 bit archs for tracing, and last but not least various test cases
for fixes that landed in bpf earlier, from Daniel.
5) Get rid of the ndo_xdp_flush API and extend the ndo_xdp_xmit with
a XDP_XMIT_FLUSH flag instead which allows to avoid one indirect
call as flushing is now merged directly into ndo_xdp_xmit(), from Jesper.
6) Add a new bpf_get_current_cgroup_id() helper that can be used in
tracing to retrieve the cgroup id from the current process in order
to allow for e.g. aggregation of container-level events, from Yonghong.
7) Two follow-up fixes for BTF to reject invalid input values and
related to that also two test cases for BPF kselftests, from Martin.
8) Various API improvements to the bpf_fib_lookup() helper, that is,
dropping MPLS bits which are not fully hashed out yet, rejecting
invalid helper flags, returning error for unsupported address
families as well as renaming flowlabel to flowinfo, from David.
9) Various fixes and improvements to sockmap BPF kselftests in particular
in proper error detection and data verification, from Prashant.
10) Two arm32 BPF JIT improvements. One is to fix imm range check with
regards to whether immediate fits into 24 bits, and a naming cleanup
to get functions related to rsh handling consistent to those handling
lsh, from Wang.
11) Two compile warning fixes in BPF, one for BTF and a false positive
to silent gcc in stack_map_get_build_id_offset(), from Arnd.
12) Add missing seg6.h header into tools include infrastructure in order
to fix compilation of BPF kselftests, from Mathieu.
13) Several formatting cleanups in the BPF UAPI helper description that
also fix an error during rst2man compilation, from Quentin.
14) Hide an unused variable in sk_msg_convert_ctx_access() when IPv6 is
not built into the kernel, from Yue.
15) Remove a useless double assignment in dev_map_enqueue(), from Colin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Return messages in extack for port split/unsplit errors. e.g.,
$ devlink port split swp1s1 count 4
Error: mlxsw_spectrum: Port cannot be split further.
devlink answers: Invalid argument
$ devlink port unsplit swp4
Error: mlxsw_spectrum: Port was not split.
devlink answers: Invalid argument
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink reset command can fail if a FIB resource limit is set to a value
lower than the current occupancy. Return a proper message indicating the
reason for the failure.
$ devlink resource sh netdevsim/netdevsim0
netdevsim/netdevsim0:
name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
resources:
name fib size unlimited occ 43 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name fib-rules size unlimited occ 4 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name IPv6 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
resources:
name fib size unlimited occ 54 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
name fib-rules size unlimited occ 3 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables none
$ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 40
$ devlink dev reload netdevsim/netdevsim0
Error: netdevsim: New size is less than current occupancy.
devlink answers: Invalid argument
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack argument to reload, port_split and port_unsplit operations.
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last patch apparently added a complete replacement for this
function, but left the old one in place, which now causes a
harmless warning:
drivers/net/ethernet/hisilicon/hns3/hns3vf/hclgevf_main.c:731:12: 'hclgevf_cfg_func_mta_filter' defined but not used
I assume it can be removed.
Fixes: 3a678b5806 ("net: hns3: Optimize the VF's process of updating multicast MAC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features.
RDMA
- Several modifications and fixes for Memory Windows
- drop vlan and tcp timestamp from mss calculation in driver for
this FW
- Fix SQ completion flow when local ack timeout is infinite
- Modifications in t10dif support
ETH
- Fix aRFS for tunneled traffic without inner IP.
- Fix chip configuration which may fail under heavy traffic conditions.
- Support receiving any-VNI in VXLAN and GENEVE RX classification.
iSCSI / FcoE
- Fix iSCSI recovery flow
- Drop vlan and tcp timestamp from mss calc for fw 8.37.2.0
Misc
- Several registers (split registers) won't read correctly with
ethtool -d
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the kvzalloc_node() error handling
case instead of 0, as done elsewhere in this function.
Fixes: 069d11465a ("net/mlx5e: RX, Enhance legacy Receive Queue memory scheme")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/en_rep.c:903:5: warning:
symbol 'mlx5e_change_rep_mtu' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending an ack to a command packet, the skb is still referenced
after it is sent to the real device. Since the real device could
free the skb, the device pointer would be invalid.
Also, remove an unnecessary variable.
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RAWIP devices such as rmnet do not have a hardware address and
instead require the kernel to generate a random IID for the
IPv6 addresses.
Signed-off-by: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM54612E have 4 multi-functional LED pins that can be configured
through register setting; the LED4 pin can be configured to a 125MHz
reference clock output by setting the spare register. Since the dedicated
CLK125 reference clock pin is not brought out on the 48-Pin MLP, the LED4
pin is the only pin to provide such function in this package, and therefore
it is beneficial to just enable the reference clock by default.
Signed-off-by: Kun Yi <kunyi@google.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation of MDIO bus PM ops doesn't actually implement
bus-specific PM ops but just calls PM ops defined on a device level
what doesn't seem to be fully in line with the core PM model.
When looking e.g. at __device_suspend() the PM core looks for PM ops
of a device in a specific order:
1. device PM domain
2. device type
3. device class
4. device bus
I think it has good reason that there's no PM ops on device level.
Now that a device type representation of PHY's as special type of MDIO
devices was added (only user of MDIO bus PM ops), the MDIO bus
PM ops can be removed including member pm of struct mdio_device.
If for some other type of MDIO device PM ops are needed, it should be
modeled as struct device_type as well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A PHY is a type of MDIO device, so let's model it as struct device_type
and place PM ops, attribute groups and release callback on device type
level. For this the attribute definitions have to be moved.
This change allows us to get rid of the PM ops on a bus level in a second
step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the ndo_xdp_flush call implementation tun_xdp_flush
as no callers of ndo_xdp_flush are left.
The tun drivers XDP_TX implementation also used tun_xdp_flush (and
tun_xdp_xmit). This is easily solved by passing the XDP_XMIT_FLUSH
flag to tun_xdp_xmit in tun_xdp_tx.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Remove the ndo_xdp_flush call implementation virtnet_xdp_flush
as no callers of ndo_xdp_flush are left.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Remove the ndo_xdp_flush call implementation ixgbe_xdp_flush
as no callers of ndo_xdp_flush are left.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Remove the ndo_xdp_flush call implementation i40e_xdp_flush
as no callers of ndo_xdp_flush are left.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-06-04
This series contains a smorgasbord of updates to documentation, e1000e,
igb, ixgbe, ixgbevf and i40e.
Benjamin Poirier fixes a potential kernel crash due to NULL pointer
dereference in e1000e.
Jeff updates the kernel documentation for e100 and e1000 to correct
default values and URLs which were incorrect in the documentation. Also
took the time to update these to the new reStructured text format for
kernel documentation.
Joanna Yurdal fixes a missing PTP transmit timestamp by ensuring that
TSICR gets cleared when ICR is cleared.
Sergey updates igb to reset all the transmit queues at one time so that
we only have to wait once for all the queues to be reset.
Alex fixes ixgbevf so that malicious driver detection (MDD) can co-exist
with XDP.
Emil and Tony extend the RTNL lock to ensure we get the most up-to-date
values for the bits and avoid a possible race condition when going down.
YueHaibing from Huawei introduces a helper function in ixgbe for
operation reads to simplify the code a bit more.
Daniel Borkmann adds support for XDP meta data when using build SKB
for i40e.
Shannon Nelson provides twp fixes for the IPSec code in ixgbe, first is
to make sure we do not try to offload the decryption of any incoming
packet that is destined for the management engine. The other fix is to
resolve a cast problem introduced by a sparse cleanup patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck