With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPuw1/AAoJEIwa5zzehBx3wbsP/RFCYzMVyz85BNLQuRyY9eO2
GCRWd0Vvy3fIfypiPdHdhkq6nIU/JnxgsfBbKX9FvWqvxXi96Ojh13KSIhSI1rQ9
t14VyuwUXaS3leeCyKxhNF1vRscz2iyEGXJqp+XEN4ckf2nrQCpKBiY5Eg9sH6/J
fvYgSBY9Lf9nFAn+/wqSKIfdvw7H0NXwUdsLvNU0uCwvrSG929bTxx2AnHX00TdJ
qf4XLhmatMg1uwdUgL/99ZxxgHlj6o55u7S6aRhUWXNXCimV6uEZ1F35ET37b+x3
YUltBCIaXjFR7iwNHmkkl42d8uyfkBznB555sY5qS3G/uF5Ma1R5I7fv8EIEy+2w
bVHsva4lj1yFazic6m8yKTET4i8n6OPiKVNqGnDsp2yb6WzOGSliKdr0Jlo1oNG2
gS69LcDZxCkXrqEq0Ht8uUoCo9TWei+qhJ6ZOJ1Z3+9ZyFq1iRTKgPVxyA5VaHaB
wwBbqKrohAwuExY8/gkAj6SYqBOF3l/J8QSB2JjXyj4trLC5UMq+l3L4cIWyMRPc
fil83hV6460CiIBoKcsnV9hDUS0oh74mv52zHo0Xj73qABqZ4dcrpHVayWjtMtpl
Z+tUpvD1rMQ+E0gdXDrwMrwILVyCDsBvpFKF4avnujDJ4WmyywtKZ+xvnpMd73VZ
YrI/+XQsMT8ZfVkkj54D
=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to
the classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided to
have them all live in one directory.
This also contains updates to existing shmobile soc code as well as some
related board changes due to dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5TAz
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for new arm SoCs from Olof Johansson:
"Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to the
classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided
to have them all live in one directory.
This also contains updates to existing shmobile soc code as well as
some related board changes due to dependencies."
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
ARM: ux500: ioremap differences for DB9540
ARM: ux500: core U9540 support
...
This adds a scratch pin control interface to the Nomadik pinctrl
driver, and defines the pins and groups in the DB8500 ASIC. We
define GPIO ranges to cover the pins exposed. The DB8500 has
more pins than this but we restrict the driver to the pins that
can be controlled from the combined GPIO and pin control hardware
to begin with.
ChangeLog v1->v2:
- Base on the latest pinctrl development from
pinctrl-mergebase-20120418 so we can get rid of legacy
group count mechanism. Also drop the range checks for group
index, this is handled by the core now.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To aid in sequential one-by-one Device Tree enablement, we split
cpu-db8500's platform_devs structure into normal platform boot, where
we leave all devices to be added in tact and a DT version where we
will remove the devices as they are DT enabled.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The DB9540 ASIC has bigger PRCMU and PRCMU TCDM memories,
so create a separate mapping table for these.
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the U9540 variant of the U8500 series. This
is an application processor without internal modem. This is the
most basic part with ASIC ID, CPU-related fixes, IRQ list, register
ranges, timer, UART, and L2 cache setup. This is based on a patch
by Michel Jaouen which was rewritten to fit with the latest 3.3
kernel.
ChangeLog v1->v2: deleted the irqs-db9540.h file since we expect to
migrate to using Device Tree for getting the IRQs to devices.
ChangeLog v2->v3: introduced a fixed virtual offset for the ROM
as suggested by Arnd Bergmann.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sebastien Pasdeloup <sebastien.pasdeloup-nonst@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At the request of Arnd Bergmann this patch moves all SoC
platform devices found in sysfs from /sys/devices/platform to
/sys/devices/soc<SoCNum>/. It is believed as the devices are
SoC specific and a /sys/devices/soc node has recently
become available, that this would be a more appropriate place to
display the data.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Here we make use of the new System-On-Chip bus driver to export
vital SoC information out to userspace via sysfs. This patch
provides a data structure of strings to populate the base
nodes found in:
/sys/devices/soc[0|1|2|...]/[family|machine|revision|soc_id].
It also adds one more node as requested by ST-Ericsson.
'process' depicts the way in which the silicon was manufactured.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch provides a means for any device within ux500
platform code to allocate its own parent. This is particularly
prudent with the introduction of /sys/devices/socX, as a
device can now proclaim to be integral part of an SoC, rather
than a more generic platform device. Latter patches make good
use of this functionality.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
The DB8500 ED (Early Drop) and V1 are only available inside of
ST-Ericsson or partners, we have actively replaced and scrapped
these prototypes. All Nova products on the open market (such as
the Snowball board) are based on V2 and later ASIC variants.
So let us focus on supporting the silicon that will be used and
delete this to get a clear overview.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The overlapping iotable mapping entries for the ux500 Cortex
A9 SCU, CPU control and TWD are no longer accepted by the
kernel. Remove the overlaps so the machine boots again.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Reported-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The <[plat|mach]/gpio.h> file is included from upper directories
and deal with generic GPIO and gpiolib stuff. Break out the
platform and driver specific defines and functions into its own
header file.
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mach-nomadik machine did not compile properly due to bad
ux500-specific functions being called. Introduce new state
variables to fix this up.
Reported-by: Axel Lin <axel.lin@gmail.com>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Prafulla Wadaskar <prafulla.wadaskar@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This updates the DB8500 PRCMU driver to the latest version
available internally. Nominally we would update the dependent
CPUfreq driver at the same time but since that is being moved
around in this patch set we postpone that by simply deactivating
it for the time being.
This is a snapshot of the current PRCMU firmware API as it looks
right now. The PRCMU firmware is still subject to change. This
also updates the CPUfreq driver to a newer version that will
utilize the new API.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Sebastien Rault <sebastien.rault@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the PRCMU base address be selected at runtime for U8500
and U5500 instead of being compiled-in.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- DMA tx and rx maps for usb channels are set to be configured at
runtime
- GPIO configurations for usb are added
- MUSB is enabled with soc specific base address, irq and dma
configurations
Signed-off-by: Mian Yousaf Kaukab <mian-yousaf.kaukab@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DB8500 has irqs from two cores ORed into one. Implement a
workaround to handle this by bouncing the interrupt by setting
the affinity to the other core when the interrupt appears to
be spurious on the current core.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dynamically detect the DBx500 SOC an revision based on the ASIC ID.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
To allow the possiblity of building U8500 and U5500 support in the same
image.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
[Rebased to latest changes in Russells tree]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This patch adds support for db8500 chip version 2.
The TCDM memory address of the PRCMU is changed and
dynamic detection of that is added.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Change the Ux500 devices to be dynamically allocated and added by
calling functions instead of referencing structures, thereby allowing
5500 and other derivatives' support to be added without having to
duplicate structures, use fixup functions, or use compile-time macros.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
This patch adds support for checking if the digital baseband (DB)
System-on-Chip (aka "cpu) ASIC hardware version is 1.0, 1.1 or
2.0. We print the result in the bootlog, the functions are then
used for runtime decisions based on hardware version.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This completes the DMA40 support with the platform-specific
configuration for U8500/DB8500.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson_nomadik_linux@list.st.com
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
[fixed up dma40_{tx|rx}_map declaration/initialization]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Move the DB8500-specific file to a more appropriate name.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds