There is no need to handle POST_PMU, POST_PMD event with
the Capture Route widget.
It is enough to handle POST_REG event, since that will come
when the user changes the routing, and we will switch the needed
bits in the registers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When digital microphones are connected to twl, delay is
needed after enabling the digimic interface of the codec.
Add new parameter for the setup data, which can be used
to pass the apropriate delay in ms after the digimic
interface has been enabled.
Without certain delay (in certain HW configuration) the
beggining of the recorded sample contains a glitch, which
is generated by the digital microphones.
Delaying the micbias1, 2 (which is the bias for the digimic0
or 1) does not help, since the glitch is coming after
switching the digimic interface.
Reversing the micbias and digimic enable order does not
work either (in that case the wait need to be added after
the micbias enabled).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Restructure the DAPM connections in order to enable
only the needed DAC (out of four in twl4030 series).
I need to keep the 'AIF Enable' supply connected to
the L2/R2 digital path, since the digital loopback
needs AIF and APLL running.
If no valid route available, than none of the DAC will
be powered, but the AIF and APLL is going to be enabled.
Furthermore, if only one audio path have valid route,
than only the corresponding DAC will be powered.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsomicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
When the gain is configured using dB value it was
not possible to use -24dB since the loopback got
muted instead of -24dB.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsomicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Machine driver can instruct the codec driver to reset the
chip registers to their default values at probe time.
If machine driver does not provide setup data, then the
registers are going to be reseted to their defaults, to
be safe.
If the developer on the platform confirms that the register
reset is not needed, than it can be skipped, saving ~20ms
time in probe.
As safety measure do the register reset at remove time also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Restructure the codec power code in order to be able to hit
off when the codec is not in use.
Since the audio registers are accessible while the codec is powered
down, there is no need for additional safety mechanism.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
It seams at least on twl5031 that the ARXR2_APGA_CTL register
does not have the same default value as it is written in
the TRM.
Since the codec part of the PM chip has not been actually
changed according to TI, assuming, that all version has
the same problem, so writing there the TRM value.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since the twl4030 codec driver supports different version
of the PM chip, a helper function can come handy, which
can check the driver's default versus the chip values.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Since the reg cache now contains the chip default values
for all registers (REG_OPTION is reset to it's default
within this patch), there is no longer need to rewrite
_all_ registers.
Initialize only few selected registers.
According to the latest information, the offset cancellation
need to be done only once, when the codec is powered on, so
there is no need for the power up wrapper.
Move all chip initialization code under chip_init, and do
it when the codec is initialized.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Add means for machine drivers to select the path for offset
cancellation.
Reset the reg cache value to the chip reset value at the
same time.
Machine drivers can specify which path need to be used for
offset cancellation via the twl4030_setup.offset_cncl_path.
For paths use the defines from
include/linux/mfd/twl4030-codec.h:
TWL4030_OFFSET_CNCL_SEL_*
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
There is no need for the power down wrapper.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Reset most of the codec registers to their chip reset
value.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The codec has support for swapping the left and right
channels in the digimic interface.
New kcontrol to handle this bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The core will ensure that the device is in either STANDBY or OFF bias
before suspending, restoring the bias in the driver is unneeded. Some
drivers doing slightly more roundabout things have been left alone
for now.
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OUTL/R are leftovers from the original driver, and they
are no longer needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch orders the APLL and AIF power sequence in
case of HiFi (audio in TWL4030 terms) playback/capture.
We also need to make sure that the AIF is running during
playback/capture, when there is no valid DAPM route
available. For this purpose I introduce these virtual
widgets:
/* To have complete playback route all the time */
DAPM_OUTPUT("Virtual HiFi OUT") /* Will keep AIF/APLL enabled */
/* To have complete capture route all the time */
DAPM_INPUT("Virtual HiFi IN") /* Will keep AIF/APLL enabled */
/* To have complete playback route for the voice module */
DAPM_OUTPUT("Virtual Voice OUT") /* Will keep APLL enabled */
The DAPM_SUPPLY widgets for APLL and AIF are placed in a way,
that during any audio activity the needed configuration of AIF
and APLL will be enabled (playback, capture, analog loopback,
digital loopback, and voice activity).
The apll reference counting code has been lifted,
and modified from Liam Girdwood's earlier patch.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
One of the features of the multi CODEC work is that it embeds a struct
device in the CODEC to provide diagnostics via a sysfs class rather than
via the device tree, at which point it's much better to use the struct
device private data rather than having two places to store it. Provide
an accessor function to allow this change to be made more easily, and
update all the CODEC drivers are updated.
To ensure use of the accessor the private data structure member is
renamed, meaning that if code developed with older an older core that
still uses private_data is merged it will fail to build.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Gain controls on outputs affect the power consumption
when the gain is set to non 0 value.
Outputs with amps have one register to configure the
routing and the gain:
PREDL_CTL (0x25):
bit 0: Voice enable
bit 1: Audio L1 enable
bit 2: Audio L2 enable
bit 3: Audio R2 enable
bit 4-5: Gain (0x0 - power down, 0x1 - 6dB, 0x2 - 0dB, 0x3 - -6dB)
bit 0 - 3: is handled in DAPM domain (DAPM_MIXER)
bit 4 - 5: has simple volume control
If there is no audio activity (BIAS_STANDBY), and
user changes the volume, than the output amplifier will
be enabled.
If the user changes the routing (but the codec remains in
BIAS_STANDBY), than the cached gain value also be written
to the register, which enables the amplifier.
The existing workaround for this is to have virtual
PGAs associated with the outputs, and whit DAPM PMD
the gain on the output will be forced to 0 (off) by
bypassing the regcache.
This failed to disable the amplifiers in several
scenario (as mentioned above).
Also if the codec is in BIAS_ON state, and user modifies
a volume control, which path is actually not enabled, than
that amplifier will be enabled as well, but it will
be not turned off, since there is no DAPM path, which
would make mute it.
To prevent amps being enabled, when they are not
needed, introduce the following workaround:
Track the state of each of this type of output.
In twl4030_write only allow actual write, when the
given output is enabled, otherwise only update
the reg_cache.
The PGA event handlers on power up will write the cached
value to the chip (restoring gain, routing selection).
On power down 0 is written to the register (disabling
the amp, and also just in case clearing the routing).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Disable the amplifiers for the headset outputs, and do not select
routings by default to the headset outputs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The serial interface (TDM/I2S) for the audio block have been
constantly enabled.
Introduce a new DAPM_SUPPLY for handling the AIF_EN bit, so
the interface is only enabled, when there is a need for it.
For example when only the analog loopback is enabled, there
is no need to keep the serial interface active.
I have added the persons who contributed to the Voice path
of twl4030 codec driver, so they might have the ability
to test this patch, and send an update for the Voice path,
if it is necessary
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module unloading path had several problems:
- it freed up the private structure twice
- it freed up the codec structure, which was allocated as part
of the private structure
- it did not freed up the reg_cache
- it did not unregistered the dais and the codec
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the legacy default register configuration, which left some
internal components on.
Now we have either DAPM, or other ways to control these bits,
so there is no need to enable them by default.
The affected parts:
Disable ADCL and ADCR
Disable ARXL2 and ARXR2 analog PGA (playback)
Disable APLL by default
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The codec structure initialization statements should be
separated by semicolons.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The DAPM widgets are now insntantiated by the core when creating the card
so there is no need for the individual CODEC drivers to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
APLL_CTL register is configured by the twl4030-codec MFD
driver.
Remove code, which makes changes in the APLL_CTL register,
and replace those with checks against the configured
audio_mclk configuration done in the MFD driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_init_card() is always called as the last part of the CODEC probe
function so we can factor it out into the core card setup rather than
have each CODEC replicate the code to do the initialiastation. This will
be required to support multiple CODECs per card.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Set the codec->bias_level to SND_SOC_BIAS_OFF before changing
the initial bias level to STANDBY.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Capture path also need the APLL enabled, adding DAPM_SUPPLY
for the Virtual ADCs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It seams that certain part of the twl4030 codec needs the APLL
enabled before they are enabled.
Paths which has any digital processing needs need the APLL
enabled before they can function.
For example the vibra output will have some random data after
it is enabled and before the APLL also enabled.
If only analog components are in use (analog bypass), than it
seams, that the APLL does not need to be enabled. This lowers
the power consumption with around ~0.005A.
Adding DAPM_SUPPLY to the Digital playback route and also
to the capture route to enable and disable the APLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes vibrator playing incoherently, when driven
with audio. There is something wrong in switch 3 at
H-bridge and VIBRA_SET still affects PWM generator.
Slowest value fixes things.
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec_muted is missleading, change it to apll_enabled,
which is what it is doing: enabing and disabling the APLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since ASoC core now handling the codec bias differently
there is no need to do the tracking of bypass switch states
anymore.
Handling of the common bit for analog loopbacks is done with
DAPM_SUPPLY for the bypass paths.
Now this bit is only enabled when there is a complete analog
bypass path, compared to the previous implementation, when the
global switch was enabled if there were any of the analog
bypass switch was on (regardless if there were complete path or
not)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the way how the twl4030 soc codec driver is
loaded/probed.
Use the device probing via tlw4030_codec MFD device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Do not rewrite the whole register, but only update the needed
bits in set_dai_sysclk functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the strings related to capture in order to be
interpreted correctly by alsamixer and possible other
UI based mixer applications.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Dynamically control and control only the needed output amplifier
muting/un-muting.
The original code was muting and un-muting the following output
amplifiers: Earpiece PreDrivL/R, CarkitL/R at the same time
regardless which pin is actually in use at the given moment.
Move these as separate PGA so only the needed amplifier will be touched.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add "set_tristate" callbacks for HiFi and Voice DAIs.
Machine drivers can enable and disable tristate for each
DAI with "snd_soc_dai_set_tristate" function.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to TRM, an external FET controlled by a 1.8V output signal
can be used to reduce the pop-noise heard when the audio amplifier is
switched on. It is suggested that GPIO6 of TWL4030 be used, but any
other gpio can be used instead. This is indicated in machine driver
with the following twl4030_setup_data members:
-hs_extmute. Set to 1 if board has support for EXTMUTE.
-set_hs_extmute. Set to a callback funcion to control an external gpio
line. Set to NULL if MUTE[GPIO6] pin is used.
Codec driver takes care of enabling and disabling this output during
the headset pop attenuation sequence.
Also add a delay to let VMID settle in ramp up sequence.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SoC dapm adds the suffix "Switch" to SND_SOC_DAPM_SWITCH controls,
removing word "Switch" from HandsfreeL/HandsfreeR widget name
for avoiding to duplicate it.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Event for voice sidetone was being interpreted as an
analog HiFi bypass event because VSTPGA register offset
is less than ARXR2_APGA_CTL offset. Reordering the
register checks allows to handle voice digital bypass
event properly.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AVDAC clk priority allows to determine the path ADC must
be connected when the codec is in option2 and both HiFi
and Voice paths are enabled.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Voice interface of twl4030 codec supports: CBM_CFM and
CBS_CFS. It doesn't support CBS_CFM.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-By: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No need to define second copies of mode and format, they're declared
with exactly the same type at the head of the function and there's no
conflict in their use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Peter Ujfalusi