Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that:
- the usb gadget patch now does not break some systems, and
actually does what it was intended to do. Many thanks to
Marek Szyprowski for quickly noticing and testing the patch
from Andy Shevchenko to resolve this issue.
- some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the original pull request patches are all here, and
they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0t32g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylFMACeLEQgeN1rmfQfLyo2NHROQEeDhnIAniLMhchZ
p9dXWJ8aNeyI5OrNjD5b
=Vd05
-----END PGP SIGNATURE-----
Merge tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
The patch addresses the compliance test failures while running TDA
2.3.1.1 and TDA 2.3.1.2 of the "PD Communications Engine USB PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
While the purpose of TDA 2.3.1.1 and TDA 2.3.1.2 is to verify that
the static and dynamic electrical capabilities of a Source meet the
requirements for each PDO offered, while doing so, the tests also
monitor that the timing of the VBUS waveform versus the messages meets
the requirements for Hard Reset defined in PROT-PROC-HR-TSTR as
mentioned in step 11 of TDA.2.3.1.1 and step 15 of TDA.2.3.1.2.
TDB.2.2.13.1: PROT-PROC-HR-TSTR Procedure and Checks for Tester
Originated Hard Reset
Purpose: To perform the appropriate protocol checks relating to any
circumstance in which the Hard Reset signal is sent by the Tester.
UUT is behaving as source:
The Tester sends a Hard Reset signal.
1. Check VBUS stays within present valid voltage range for
tPSHardReset min (25ms) after last bit of Hard Reset signal.
[PROT_PROC_HR_TSTR_1]
2. Check that VBUS starts to fall below present valid voltage range by
tPSHardReset max (35ms). [PROT_PROC_HR_TSTR_2]
3. Check that VBUS reaches vSafe0V within tSafe0v max (650 ms).
[PROT_PROC_HR_TSTR_3]
4. Check that VBUS starts rising to vSafe5V after a delay of
tSrcRecover (0.66s - 1s) from reaching vSafe0V. [PROT_PROC_HR_TSTR_4]
5. Check that VBUS reaches vSafe5V within tSrcTurnOn max (275ms) of
rising above vSafe0v max (0.8V). [PROT_PROC_HR_TSTR_5] Power Delivery
Compliance Plan 139 6. Check that Source Capabilities are finished
sending within tFirstSourceCap max (250ms) of VBUS reaching vSafe5v
min. [PROT_PROC_HR_TSTR_6].
This is in line with 7.1.5 Response to Hard Resets of the USB Power
Delivery Specification Revision 3.0, Version 1.2,
"Hard Reset Signaling indicates a communication failure has occurred
and the Source Shall stop driving VCONN, Shall remove Rp from the
VCONN pin and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The
USB connection May reset during a Hard Reset since the VBUS voltage
will be less than vSafe5V for an extended period of time. After
establishing the vSafe0V voltage condition on VBUS, the Source Shall
wait tSrcRecover before re-applying VCONN and restoring VBUS to
vSafe5V. A Source Shall conform to the VCONN timing as specified in
[USB Type-C 1.3]."
With the above guidelines from the spec in mind, TCPM does not turn
off VCONN while entering SRC_HARD_RESET_VBUS_OFF. The patch makes TCPM
turn off VCONN while entering SRC_HARD_RESET_VBUS_OFF and turn it back
on while entering SRC_HARD_RESET_VBUS_ON along with vbus instead of
having VCONN on through hardreset.
Also, the spec clearly states that "After establishing the vSafe0V
voltage condition on VBUS", the Source Shall wait tSrcRecover before
re-applying VCONN and restoring VBUS to vSafe5V.
TCPM does not conform to this requirement. If the TCPC driver calls
tcpm_vbus_change with vbus off signal, TCPM right away enters
SRC_HARD_RESET_VBUS_ON without waiting for tSrcRecover.
For TCPC's which are buggy/does not call tcpm_vbus_change, TCPM
assumes that the vsafe0v is instantaneous as TCPM only waits
tSrcRecover instead of waiting for tSafe0v + tSrcRecover.
This patch also fixes this behavior by making sure that TCPM waits for
tSrcRecover before transitioning into SRC_HARD_RESET_VBUS_ON when
tcpm_vbus_change is called by TCPC.
When TCPC does not call tcpm_vbus_change, TCPM assumes the worst case
i.e. tSafe0v + tSrcRecover before transitioning into
SRC_HARD_RESET_VBUS_ON.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20200817184601.1899929-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race
during registration") made the ucsi code hold con->lock in
ucsi_register_displayport(). But we really don't want any interactions
with the connector to run before the port-registration process is fully
complete.
This commit moves the taking of con->lock from ucsi_register_displayport()
into ucsi_register_port() to achieve this.
Cc: stable@vger.kernel.org
Fixes: 081da1325d ("usb: typec: ucsi: displayport: Fix a potential race during registration")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
Push the taking of the lock down into these 2 functions, renaming
ucsi_run_command() to ucsi_send_command() which was an existing
wrapper already taking the lock for its callers.
This simplifies things for the callers and removes the difference
between ucsi_send_command() and ucsi_run_command() which has led
to various locking bugs in the past.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix 2 unlocked ucsi_run_command calls:
1. ucsi_handle_connector_change() contains one ucsi_send_command() call,
which takes the ppm_lock for it; and one ucsi_run_command() call which
relies on the caller have taking the ppm_lock.
ucsi_handle_connector_change() does not take the lock, so the
second (ucsi_run_command) calls should also be ucsi_send_command().
2. ucsi_get_pdos() gets called from ucsi_handle_connector_change() which
does not hold the ppm_lock, so it also must use ucsi_send_command().
This commit also adds a WARN_ON(!mutex_is_locked(&ucsi->ppm_lock)); to
ucsi_run_command() to avoid similar problems getting re-introduced in
the future.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lockdep reports an AB BA lock inversion between ucsi_init() and
ucsi_handle_connector_change():
AB order:
1. ucsi_init takes ucsi->ppm_lock (it runs with that locked for the
duration of the function)
2. usci_init eventually end up calling ucsi_register_displayport,
which takes ucsi_connector->lock
BA order:
1. ucsi_handle_connector_change work is started, takes ucsi_connector->lock
2. ucsi_handle_connector_change calls ucsi_send_command which takes
ucsi->ppm_lock
The ppm_lock really only needs to be hold during 2 functions:
ucsi_reset_ppm() and ucsi_run_command().
This commit fixes the AB BA lock inversion by making ucsi_init drop the
ucsi->ppm_lock before it starts registering ports; and replacing any
ucsi_run_command() calls after this point with ucsi_send_command()
(which is a wrapper around run_command taking the lock while handling
the command).
Some of the replacing of ucsi_run_command with ucsi_send_command
in the helpers used during port registration also fixes a number of
code paths after registration which call ucsi_run_command() without
holding the ppm_lock:
1. ucsi_altmode_update_active() call in ucsi/displayport.c
2. ucsi_register_altmodes() call from ucsi_handle_connector_change()
(through ucsi_partner_change())
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200809141904.4317-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tcpm.c code for sending VDMs assumes that there will only be one VDM
in flight at the time. The "queue" used by tcpm_queue_vdm is only 1 entry
deep.
This assumes that the higher layers (tcpm state-machine and alt-mode
drivers) ensure that queuing a new VDM before the old one has been
completely send (or it timed out) add a WARN_ON to check for this.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-6-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we receive a PD data packet which ends up being for the alt-mode
driver we have the following lock order:
1. tcpm_pd_rx_handler take the tcpm-port lock
2. We call into the alt-mode driver which takes the alt-mode's lock
And when the alt-mode driver initiates communication we have the following
lock order:
3. alt-mode driver takes the alt-mode's lock
4. alt-mode driver calls tcpm_altmode_enter which takes the tcpm-port lock
This is a classic AB BA lock inversion issue.
With the refactoring of tcpm_handle_vdm_request() done before this patch,
we don't rely on, or need to make changes to the tcpm-port data by the
time we make call 2. from above. All data to be passed to the alt-mode
driver sits on our stack at this point, and thus does not need locking.
So after the refactoring we can simply fix this by releasing the
tcpm-port lock before calling into the alt-mode driver.
This fixes the following lockdep warning:
[ 191.454238] ======================================================
[ 191.454240] WARNING: possible circular locking dependency detected
[ 191.454244] 5.8.0-rc5+ #1 Not tainted
[ 191.454246] ------------------------------------------------------
[ 191.454248] kworker/u8:5/794 is trying to acquire lock:
[ 191.454251] ffff9bac8e30d4a8 (&dp->lock){+.+.}-{3:3}, at: dp_altmode_vdm+0x30/0xf0 [typec_displayport]
[ 191.454263]
but task is already holding lock:
[ 191.454264] ffff9bac9dc240a0 (&port->lock#2){+.+.}-{3:3}, at: tcpm_pd_rx_handler+0x43/0x12c0 [tcpm]
[ 191.454273]
which lock already depends on the new lock.
[ 191.454275]
the existing dependency chain (in reverse order) is:
[ 191.454277]
-> #1 (&port->lock#2){+.+.}-{3:3}:
[ 191.454286] __mutex_lock+0x7b/0x820
[ 191.454290] tcpm_altmode_enter+0x23/0x90 [tcpm]
[ 191.454293] dp_altmode_work+0xca/0xe0 [typec_displayport]
[ 191.454299] process_one_work+0x23f/0x570
[ 191.454302] worker_thread+0x55/0x3c0
[ 191.454305] kthread+0x138/0x160
[ 191.454309] ret_from_fork+0x22/0x30
[ 191.454311]
-> #0 (&dp->lock){+.+.}-{3:3}:
[ 191.454317] __lock_acquire+0x1241/0x2090
[ 191.454320] lock_acquire+0xa4/0x3d0
[ 191.454323] __mutex_lock+0x7b/0x820
[ 191.454326] dp_altmode_vdm+0x30/0xf0 [typec_displayport]
[ 191.454330] tcpm_pd_rx_handler+0x11ae/0x12c0 [tcpm]
[ 191.454333] process_one_work+0x23f/0x570
[ 191.454336] worker_thread+0x55/0x3c0
[ 191.454338] kthread+0x138/0x160
[ 191.454341] ret_from_fork+0x22/0x30
[ 191.454343]
other info that might help us debug this:
[ 191.454345] Possible unsafe locking scenario:
[ 191.454347] CPU0 CPU1
[ 191.454348] ---- ----
[ 191.454350] lock(&port->lock#2);
[ 191.454353] lock(&dp->lock);
[ 191.454355] lock(&port->lock#2);
[ 191.454357] lock(&dp->lock);
[ 191.454360]
*** DEADLOCK ***
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor tcpm_handle_vdm_request and its tcpm_pd_svdm helper function so
that reporting the results of the vdm to the altmode-driver is separated
out into a clear separate step inside tcpm_handle_vdm_request, instead
of being scattered over various places inside the tcpm_pd_svdm helper.
This is a preparation patch for fixing an AB BA lock inversion between the
tcpm code and some altmode drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the tcpm_handle_vdm_request payload handling by doing the
endianness conversion only once directly inside tcpm_handle_vdm_request
itself instead of doing it multiple times inside various helper functions
called by tcpm_handle_vdm_request.
This is a preparation patch for some further refactoring to fix an AB BA
lock inversion between the tcpm code and some altmode drivers.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Various callers (all the typec_altmode_ops) take the port-lock just for
the tcpm_queue_vdm() call.
Add a new tcpm_queue_vdm_unlocked() helper which takes the lock, so that
its callers don't have to do this themselves.
This is a preparation patch for fixing an AB BA lock inversion between
the tcpm code and some altmode drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-2-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All callers of tcpm_queue_vdm() immediately follow the tcpm_queue_vdm()
vdm call with a:
mod_delayed_work(port->wq, &port->vdm_state_machine, 0);
Call, fold this into tcpm_queue_vdm() itself.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20200724174702.61754-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port starts to toggle when transitioning to unattached state.
This is incorrect while in BIST mode.
6.4.3.1 BIST Carrier Mode
Upon receipt of a BIST Message, with a BIST Carrier Mode BIST Data Object,
the UUT Shall send out a continuous string of BMC encoded alternating "1"s
and “0”s. The UUT Shall exit the Continuous BIST Mode within
tBISTContMode of this Continuous BIST Mode being enabled(see
Section 6.6.7.2).
6.4.3.2 BIST Test Data
Upon receipt of a BIST Message, with a BIST Test Data BIST Data Object,
the UUT Shall return a GoodCRC Message and Shall enter a test mode in which
it sends no further Messages except for GoodCRC Messages in response to
received Messages. See Section 5.9.2 for the definition of the Test Data
Frame. The test Shall be ended by sending Hard Reset Signaling to reset the
UUT.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quoting from TCPCI spec:
"Setting this bit to 1 is intended to be used only when a USB compliance
tester is using USB BIST Test Data to test the PHY layer of the TCPC. The
TCPM should clear this bit when a disconnect is detected.
0: Normal Operation. Incoming messages enabled by RECEIVE_DETECT
passed to TCPM via Alert.
1: BIST Test Mode. Incoming messages enabled by RECEIVE_DETECT
result in GoodCRC response but may not be passed to the TCPM via
Alert."
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TCPM supports BIST carried mode. PD compliance tests require
BIST Test Data to be supported as well.
Introducing set_bist_data callback to signal tcpc driver for
configuring the port controller hardware to enable/disable
BIST Test Data mode.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pmc_usb_mux_set() is invoked when a device is disconnected, a valid
scenario is for state->alt == NULL and state->mode == TYPEC_STATE_USB.
In such cases, if a pmc_usb_disconnect() has already been issued (from
either pmc_usb_set_orientation() when orientation ==
TYPEC_ORIENTATION_NONE, or pmc_usb_set_role() when role ==
USB_ROLE_NONE), a pmc_usb_connect() will be issued despite no peripheral
being present.
This confuses the PMC and leads to all subsequent PMC IPC requests
returning errors due to timeout.
To prevent this, return early if the port orientation or role is already
set to none.
Cc: Benson Leung <bleung@chromium.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Rajmohan Mani <rajmohan.mani@intel.com>
Fixes: f3c1c41ebc ("usb: typec: intel_pmc_mux: Add support for USB4")
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20200709002441.1309189-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200711135825.19862-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It isn't called from anywhere outside of ucsi.c.
Fixes the following W=1 kernel build warning(s):
drivers/usb/typec/ucsi/ucsi.c:1005:5: warning: no previous prototype for ‘ucsi_init’ [-Wmissing-prototypes]
1005 | int ucsi_init(struct ucsi *ucsi)
| ^~~~~~~~~
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200706133341.476881-25-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/typec/tcpm/fusb302.c: In function ‘fusb302_log’:
drivers/usb/typec/tcpm/fusb302.c:186:2: warning: function ‘fusb302_log’ might be a candidate for ‘gnu_printf’ format attribute [-Wsuggest-attribute=format]
186 | _fusb302_log(chip, fmt, args);
| ^~~~~~~~~~~~
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Yueyao Zhu <yueyao.zhu@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200703174148.2749969-23-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the header file containing a function's prototype isn't included by
the sourcefile containing the associated function, the build system
complains of missing prototypes.
Fixes the following W=1 kernel build warning(s):
drivers/usb/typec/altmodes/displayport.c:511:5: warning: no previous prototype for ‘dp_altmode_probe’ [-Wmissing-prototypes]
drivers/usb/typec/altmodes/displayport.c:551:6: warning: no previous prototype for ‘dp_altmode_remove’ [-Wmissing-prototypes]
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-22-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Demote displayport's file header to a standard comment block.
Fixes the following W=1 kernel build warning(s):
drivers/usb/typec/altmodes/displayport.c:18: warning: Function parameter or member '_dp' not described in 'DP_HEADER'
drivers/usb/typec/altmodes/displayport.c:18: warning: Function parameter or member 'cmd' not described in 'DP_HEADER'
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200703174148.2749969-21-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMC mux-agent can be used also to enter USB4 mode. The
mux-agent does not have USB4 specific message, but it can be
put into the TBT3 alternate mode also with USB4. That is OK
because the controller is in any case the same with TBT3 and
USB4.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200701115618.22482-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding definitions for the two status bits that we have in
the command response data structure.
Also, from now on only considering the second status bit,
which tells was the failure fatal or not, if the first bit
is set. If the first bit is not set, then the command was
successful, and we need to ignore the second bit.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200701115618.22482-4-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
John reported screaming irq caused by rt1711h when system boot[1],
this is because irq request is done before tcpci_register_port(),
so the chip->tcpci has not been setup, irq handler is entered but
can't do anything, this patch is to address this by moving the irq
request after tcpci_register_port().
[1] https://lore.kernel.org/linux-usb/20200530040157.31038-1-john.stultz@linaro.org
Fixes: ce08eaeb63 ("staging: typec: rt1711h typec chip driver")
Cc: stable <stable@vger.kernel.org> # v4.18+
Cc: John Stultz <john.stultz@linaro.org>
Reported-and-tested-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Link: https://lore.kernel.org/r/20200604112118.38062-1-jun.li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PMC needs to be notified separately about HPD (hotplug
detected) signal being high after mode entry. There is a bit
"HPD High" in the Alternate Mode Request that the driver
already sets, but that bit is only valid when the
DisplayPort Alternate Mode is directly entered from
disconnected state.
Fixes: 5c4edcdbcd ("usb: typec: mux: intel: Fix DP_HPD_LVL bit field")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Prashant Malani <pmalani@chromium.org>
Link: https://lore.kernel.org/r/20200529131753.15587-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
* Add a support of the media keys on the ASUS laptop UX325JA/UX425JA
* ASUS WMI driver can now handle 2-in-1 models T100TA, T100CHI, T100HA, T200TA
* Big refactoring of Intel SCU driver with Elkhart Lake support has been added
* Slim Bootloarder firmware update signaling WMI driver has been added
* Thinkpad ACPI driver can handle dual fan configuration on new P and X models
* Touchscreen DMI driver has been extended to support
- MP-man MPWIN895CL tablet
- ONDA V891 v5 tablet
- techBite Arc 11.6
- Trekstor Twin 10.1
- Trekstor Yourbook C11B
- Vinga J116
* Virtual Button driver got a few fixes to detect mode of 2-in-1 tablet models
* Intel Speed Select tools update
* Plenty of small cleanups here and there
The following is an automated git shortlog grouped by driver:
acerhdf:
- replace space by * in modalias
New drivers:
- Add Elkhart Lake SCU/PMC support
- Add Slim Bootloader firmware update signaling driver
asus-laptop:
- Drop duplicate check for led_classdev_unregister()
asus-nb-wmi:
- Revert "Do not load on Asus T100TA and T200TA"
- Do not load on Asus T100TA and T200TA
asus-wmi:
- Ignore WMI events with code 0x79
- Add support for SW_TABLET_MODE
- Move asus_wmi_input_init and _exit lower in the file
- Drop duplicate check for led_classdev_unregister()
- Reserve more space for struct bias_args
- remove redundant initialization of variable status
dcdbas:
- Check SMBIOS for protected buffer address
dell-laptop:
- don't register micmute LED if there is no token
dell-wmi:
- Ignore keyboard attached / detached events
device property:
- export set_secondary_fwnode() to modules
eeepc-laptop:
- Drop duplicate check for led_classdev_unregister()
hp-wmi:
- Introduce HPWMI_POWER_FW_OR_HW as convenient shortcut
- Convert simple_strtoul() to kstrtou32()
- Refactor postcode_store() to follow standard patterns
intel_cht_int33fe:
- Fix spelling issues
- Switch to use acpi_dev_hid_uid_match()
- Convert to use set_secondary_fwnode()
- Convert software node array to group
intel-hid:
- Add a quirk to support HP Spectre X2 (2015)
intel_mid_powerbtn:
- Convert to use new SCU IPC API
intel_pmc_core:
- avoid unused-function warnings
- Change Jasper Lake S0ix debug reg map back to ICL
intel_pmc_ipc:
- Convert to MFD
- Move PCI IDs to intel_scu_pcidrv.c
- Drop intel_pmc_ipc_command()
- Start using SCU IPC
intel_scu_ipc:
- Add managed function to register SCU IPC
- Introduce new SCU IPC API
- Move legacy SCU IPC API to a separate header
- Log more information if SCU IPC command fails
- Split out SCU IPC functionality from the SCU driver
intel_scu_ipcutil:
- Convert to use new SCU IPC API
intel-speed-select:
- Fix speed-select-base-freq-properties output on CLX-N
intel_telemetry:
- Add telemetry_get_pltdata()
- Convert to use new SCU IPC API
intel-vbtn:
- Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type
- Detect switch position before registering the input-device
- Move detect_tablet_mode() to higher in the file
- Fix probe failure on devices with only switches
- Also handle tablet-mode switch on "Detachable" and "Portable" chassis-types
- Do not advertise switches to userspace if they are not there
- Split keymap into buttons and switches parts
- Use acpi_evaluate_integer()
ISST:
- Increase timeout
lg-laptop:
- Drop duplicate check for led_classdev_unregister()
MAINTAINERS:
- Add me as maintainer of Intel SCU drivers
- Update entry for Intel Broxton PMC driver
Merges of immutable branches:
- Merge branch 'for-next'
- Merge branch 'ib-mfd-x86-usb-watchdog-v5.7'
- Merge branch 'ib-pdx86-properties'
mfd:
- intel_soc_pmic_mrfld: Convert to use new SCU IPC API
- intel_soc_pmic_bxtwc: Convert to use new SCU IPC API
- intel_soc_pmic: Add SCU IPC member to struct intel_soc_pmic
samsung-laptop:
- Drop duplicate check for led_classdev_unregister()
software node:
- Allow register and unregister software node groups
sony-laptop:
- Make resuming thermal profile safer
- SNC calls should handle BUFFER types
thinkpad_acpi:
- Replace custom approach by kstrtoint()
- Use strndup_user() in dispatch_proc_write()
- Replace next_cmd(&buf) with strsep(&buf, ",")
- Drop duplicate check for led_classdev_unregister()
- Remove always false 'value < 0' statement
- Add support for dual fan control
tools/power/x86/intel-speed-select:
- Fix invalid core mask
- Increase CPU count
- Fix json perf-profile output output
- Update version
- Enable clos for turbo-freq enable
- Fix CLX-N package information output
- Check support status before enable
- Change debug to error
toshiba_acpi:
- Drop duplicate check for led_classdev_unregister()
touchscreen_dmi:
- Update Trekstor Twin 10.1 entry
- Add info for the Trekstor Yourbook C11B
- Drop comma in terminator line
- add Vinga J116 touchscreen
- Add info for the ONDA V891 v5 tablet
- Add touchscreen info for techBite Arc 11.6.
- Add info for the MP-man MPWIN895CL tablet
usb:
- typec: mux: Convert the Intel PMC Mux driver to use new SCU IPC API
watchdog:
- iTCO: fix link error
- intel-mid_wdt: Convert to use new SCU IPC API
wmi:
- Describe function parameters
- Fix indentation in some cases
- Replace UUID redefinitions by their originals
x86/platform/intel-mid:
- Add empty stubs for intel_scu_devices_[create|destroy]()
-----BEGIN PGP SIGNATURE-----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=pprB
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.8-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Andy Shevchenko:
- Add a support of the media keys on the ASUS laptop UX325JA/UX425JA
- ASUS WMI driver can now handle 2-in-1 models T100TA, T100CHI, T100HA,
T200TA
- Big refactoring of Intel SCU driver with Elkhart Lake support has
been added
- Slim Bootloarder firmware update signaling WMI driver has been added
- Thinkpad ACPI driver can handle dual fan configuration on new P and X
models
- Touchscreen DMI driver has been extended to support
- MP-man MPWIN895CL tablet
- ONDA V891 v5 tablet
- techBite Arc 11.6
- Trekstor Twin 10.1
- Trekstor Yourbook C11B
- Vinga J116
- Virtual Button driver got a few fixes to detect mode of 2-in-1 tablet
models
- Intel Speed Select tools update
- Plenty of small cleanups here and there
* tag 'platform-drivers-x86-v5.8-1' of git://git.infradead.org/linux-platform-drivers-x86: (89 commits)
platform/x86: dcdbas: Check SMBIOS for protected buffer address
platform/x86: asus_wmi: Reserve more space for struct bias_args
platform/x86: intel-vbtn: Only blacklist SW_TABLET_MODE on the 9 / "Laptop" chasis-type
platform/x86: intel-hid: Add a quirk to support HP Spectre X2 (2015)
platform/x86: touchscreen_dmi: Update Trekstor Twin 10.1 entry
platform/x86: touchscreen_dmi: Add info for the Trekstor Yourbook C11B
platform/x86: hp-wmi: Introduce HPWMI_POWER_FW_OR_HW as convenient shortcut
platform/x86: hp-wmi: Convert simple_strtoul() to kstrtou32()
platform/x86: hp-wmi: Refactor postcode_store() to follow standard patterns
platform/x86: acerhdf: replace space by * in modalias
platform/x86: ISST: Increase timeout
tools/power/x86/intel-speed-select: Fix invalid core mask
tools/power/x86/intel-speed-select: Increase CPU count
tools/power/x86/intel-speed-select: Fix json perf-profile output output
platform/x86: dell-wmi: Ignore keyboard attached / detached events
platform/x86: dell-laptop: don't register micmute LED if there is no token
platform/x86: thinkpad_acpi: Replace custom approach by kstrtoint()
platform/x86: thinkpad_acpi: Use strndup_user() in dispatch_proc_write()
platform/x86: thinkpad_acpi: Replace next_cmd(&buf) with strsep(&buf, ",")
platform/x86: intel-vbtn: Detect switch position before registering the input-device
...
When I switched on USB role switching for the tps6598x I completely forgot
to add the Kconfig dependency.
Ensure USB_ROLE_SWITCH is selected to prevent the typs6598x driver being
compiled in but the role-switch driver being compiled as a module, leading
to link error.
Suggested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200520153617.610909-1-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, the PMC HPD request LVL bit field is bit 4.
Fix the definition here to match the programming guide.
Since this bit field is changing, explicitly define a field for the
HPD_HIGH mode data bit.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200511091837.102508-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds USB role switch support to the tps6598x.
The setup to initiate or accept a data-role switch is both assumed and
currently required to be baked-into the firmware as described in TI's
document here.
Link: https://www.ti.com/lit/an/slva843a/slva843a.pdf
With this change its possible to use the USB role-switch API to detect and
notify role-switches to downstream consumers.
Tested with a ChipIdea controller on a Qualcomm MSM8939.
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20200511231930.2825183-2-bryan.odonoghue@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBU and HSL orientation may be fixed/static from the mux
PoW. Apparently the retimer may take care of the orientation
of these lines. Handling the static SBU (AUX) and HSL
orientation with device properties.
If the SBU orientation is static, a device property
"sbu-orintation" can be used. When the property exists, the
driver always sets the SBU orientation according to the
property value, and when it's not set, the driver uses the
cable plug orientation with SBU.
And with static HSL orientation, "hsl-orientation" device
property can be used in the same way.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200507150900.12102-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the PMC Type C Subsystem (TCSS) Mux programming guide rev
0.6, when a device is transitioning to DP Alternate Mode state, if the
HPD_STATE (bit 7) field in the status update command VDO is set to
HPD_HIGH, the HPD_HIGH field in the Alternate Mode request “mode_data”
field (bit 14) should also be set. Ensure the bit is correctly handled
while issuing the Alternate Mode request.
Signed-off-by: Prashant Malani <pmalani@chromium.org>
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200429054432.134178-1-pmalani@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device property names for the port index number are
"usb2-port-number" and "usb3-port-number", not "usb2-port"
and "usb3-port".
Fixes: 6701adfa96 ("usb: typec: driver for Intel PMC mux control")
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200430135657.45169-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stub was ucsi_register_port() when it should have been
ucsi_register_port_psy().
Cc: Abhilash K V <abhilash.k.v@intel.com>
Fixes: 992a60ed0d ("usb: typec: ucsi: register with power_supply class")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200427111246.4889-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver only creates a bunch of platform devices sharing resources
belonging to the PMC device. This is pretty much what MFD subsystem is
for so move the driver there, renaming it to intel_pmc_bxt.c which
should be more clear what it is.
MFD subsystem provides nice helper APIs for subdevice creation so
convert the driver to use those. Unfortunately the ACPI device includes
separate resources for most of the subdevices so we cannot simply call
mfd_add_devices() to create all of them but instead we need to call it
separately for each device.
The new MFD driver continues to expose two sysfs attributes that allow
userspace to send IPC commands to the PMC/SCU to avoid breaking any
existing applications that may use these. Generally this is bad idea so
document this in the ABI documentation.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Convert the driver to use the new SCU IPC API. This allows us to get rid
of the duplicate PMC IPC implementation which is now covered in SCU IPC
driver.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With this change the UCSI device will show up in
/sys/class/power_supply/. The following values are exported:
- online
- usb_type
- voltage_min
- voltage_max
- voltage_now
- current_max
- current_now
Once a PD-capable type-C power source is connected to the system, GET_PDOS
UCSI command is used to query all source capabilities. Request data object
(RDO) is used to get current values.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-7-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When connected to a PD-capable power-source, read & save all partner
power data objects (PDOs) by using GET_PDOS UCSI command.
Also, save the current power contract in request data object (RDO)
for that connector.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-6-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 0 is reserved in CCI (Command Status & Connector Change Indicator)
register. So, change bit-mask for connector number field to 7..1
instead of 7..0.
There would be no functional change since we were anyways right-shifing
by 1 bit.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-5-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
EC firmware on Dell XPS & Latitude series does not set "Power Operation
Mode Change" bit in "Connector Status change" field of MESSAGE IN Data
while transitioning from type-C current to PD mode.
Instead the "Negotiated Power Level Change" bit is set when the "Power
Operation Mode" field shows the correct mode (i.e. PD).
This patch adds a check for this bit also, to trigger an update of
power operation mode in class driver, while handling GET_CONNECTOR_STATUS
command.
Signed-off-by: K V, Abhilash <abhilash.k.v@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently UCSI framework doesn't update USB data role when partner type
is reported as power cable or power cable with ufp connected. This
results into no USB host mode functionality. This is valid usecase where
user wants to use legacy type c power cable with type a female connector
to attach different USB devices like mouse, thumb drive etc. Hence update
USB data role as host when partner type is reported as power cable or
power cable with ufp connected.
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200423132058.6972-2-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds