Currently SoCs pass2.x do not emulate EA headers for ACPI boot method at
all. However, for pass2.x some devices (like EDAC) advertise incorrect
base addresses in their BARs which results in driver probe failure during
resource request. Since all problematic blocks are on 2nd NUMA node under
domain 10 add necessary quirk entry to obtain BAR addresses correction
using EA header emulation.
Fixes: 44f22bd91e ("PCI: Add MCFG quirks for Cavium ThunderX pass2.x host controller")
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Robert Richter <rrichter@cavium.com>
CC: stable@vger.kernel.org # v4.10+
With no blank lines, it's not obvious where the macro definitions end and
the uses begin. Add some blank lines and reorder the ThunderX definitions.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.10+
The configuration data provided by an MCFG entry, i.e., PCI segment and bus
range, may span multiple host bridges.
pci_mcfg_lookup() previously required an exact match of the host bridge
starting bus and the MCFG starting bus, which made the following
configuration fail:
MCFG region:
segment: 0
bus range: 0x00-0xff
host bridge
segment: 0
bus range: 0x20-0x4f
Relax the bus range check in pci_mcfg_lookup() so we can use any MCFG entry
that contains the required bus range, as we do in pci_mmconfig_lookup().
[bhelgaas: changelog]
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tomasz Nowicki <tn@semihalf.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
PCIe controllers in X-Gene SoCs are not ECAM compliant: software needs to
configure additional controller's register to address device at
bus:dev:function.
Add a quirk to discover controller MMIO register space and configure
controller registers to select and address the target secondary device.
The quirk will only be applied for X-Gene PCIe MCFG table with
OEM revison 1, 2, 3 or 4 (PCIe controller v1 and v2 on X-Gene SoCs).
Tested-by: Jon Masters <jcm@redhat.com>
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX pass1.x requires to emulate the EA headers for on-chip devices
hence it has to use custom pci_thunder_ecam_ops for accessing PCI config
space (pci-thunder-ecam.c). Add new entries to MCFG quirk array where it
can be applied while probing ACPI based PCI host controller.
ThunderX pass1.x is using the same way for accessing off-chip devices
(so-called PEM) as silicon pass-2.x so we need to add PEM quirk entries
too.
Quirk is considered for ThunderX silicon pass1.x only which is identified
via MCFG revision 2.
ThunderX pass 1.x requires the following accessors:
NUMA node 0 PCI segments 0- 3: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 10-13: pci_thunder_ecam_ops (MCFG quirk)
NUMA node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: change Makefile/ifdefs so quirk doesn't depend on
CONFIG_PCI_HOST_THUNDER_ECAM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ThunderX PCIe controller to off-chip devices (so-called PEM) is not fully
compliant with ECAM standard. It uses non-standard configuration space
accessors (see thunder_pem_ecam_ops) and custom configuration space
granulation (see bus_shift = 24). In order to access configuration space
and probe PEM as ACPI-based PCI host controller we need to add MCFG quirk
infrastructure. This involves:
1. A new thunder_pem_acpi_init() init function to locate PEM-specific
register ranges using ACPI.
2. Export PEM thunder_pem_ecam_ops structure so it is visible to MCFG quirk
code.
3. New quirk entries for each PEM segment. Each contains platform IDs,
mentioned thunder_pem_ecam_ops and CFG resources.
Quirk is considered for ThunderX silicon pass2.x only which is identified
via MCFG revision 1.
ThunderX pass 2.x requires the following accessors:
NUMA Node 0 PCI segments 0- 3: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 0 PCI segments 4- 9: thunder_pem_ecam_ops (MCFG quirk)
NUMA Node 1 PCI segments 10-13: pci_generic_ecam_ops (ECAM-compliant)
NUMA Node 1 PCI segments 14-19: thunder_pem_ecam_ops (MCFG quirk)
[bhelgaas: adapt to use acpi_get_rc_resources(), update Makefile/ifdefs so
quirk doesn't depend on CONFIG_PCI_HOST_THUNDER_PEM]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe controller in Hip05/Hip06/Hip07 SoCs is not completely
ECAM-compliant. It is non-ECAM only for the RC bus config space; for any
other bus underneath the root bus it does support ECAM access.
Add specific quirks for PCI config space accessors. This involves:
1. New initialization call hisi_pcie_init() to obtain RC base
addresses from PNP0C02 at the root of the ACPI namespace (under \_SB).
2. New entry in common quirk array.
[bhelgaas: move to pcie-hisi.c and change Makefile/ifdefs so quirk doesn't
depend on CONFIG_PCI_HISI]
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Qualcomm Technologies QDF2432 SoC does not support accesses smaller
than 32 bits to the PCI configuration space. Register the appropriate
quirk.
[bhelgaas: add QCOM_ECAM32 macro, ifdef for ACPI and PCI_QUIRKS]
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCIe spec (r3.0, sec 7.2.2) specifies an "Enhanced Configuration Access
Mechanism" (ECAM) for memory-mapped access to configuration space. ECAM is
required for PCIe systems unless there's a standard firmware interface for
config access.
In the absence of a firmware interface, we use pci_generic_ecam_ops, and on
ACPI systems, we discover the ECAM space via the MCFG table and/or the _CBA
method.
Unfortunately some systems provide MCFG but don't implement ECAM according
to spec, so we need a mechanism for quirks to make those systems work.
Add an MCFG quirk mechanism to override the config accessor functions
and/or the memory-mapped address space.
A quirk is selected if it matches all of the following:
- OEM ID
- OEM Table ID
- OEM Revision
- PCI segment (from _SEG)
- PCI bus number range (from _CRS, wildcard allowed)
If the quirk specifies config accessor functions or a memory-mapped address
range, these override the defaults.
[bhelgaas: changelog, reorder quirk matching, fix oem_revision typo per
Duc, add under #ifdef CONFIG_PCI_QUIRKS]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Christopher Covington <cov@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_mcfg_lookup() is the external interface to the generic MCFG code.
Previously it merely looked up the ECAM base address for a given domain and
bus range. We want a way to add MCFG quirks, some of which may require
special config accessors and adjustments to the ECAM address range.
Extend pci_mcfg_lookup() so it can return a pointer to a pci_ecam_ops
structure and a struct resource for the ECAM address space. For now, it
always returns &pci_generic_ecam_ops (the standard accessor) and the
resource described by the MCFG.
No functional changes intended.
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On ACPI systems that support memory-mapped config space access, i.e., ECAM,
the PCI Firmware Specification says the OS can learn where the ECAM space
is from either:
- the static MCFG table (for non-hotpluggable bridges), or
- the _CBA method (for hotpluggable bridges)
The current MCFG table handling code cannot be easily generalized owing to
x86-specific quirks, which makes it hard to reuse on other architectures.
Implement generic MCFG handling from scratch, including:
- Simple MCFG table parsing (via pci_mmcfg_late_init() as in current x86)
- MCFG region lookup for a (domain, bus_start, bus_end) tuple
[bhelgaas: changelog]
Signed-off-by: Tomasz Nowicki <tn@semihalf.com>
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tomasz Nowicki