*map should be tested for NULL instead of map.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Marvell's PXA/MMP silicon also match the behavior of pinctrl-single.
Each pin binds to one register. A lot of pins could be configured
as gpio.
GPIO range is defined as a child node of pinmux in .dtsi file. If those
pins are with the same gpio function configuration in the pinmux
register, they could be defined in the same GPIO range. For this new
child node, two properties are used.
reg = <the start of pinmux register in range, size of range>
pinctrl-single,gpio: <gpio base in range, the gpio function of the range
in the pinmux register>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Dump pinmux register value, not only function part in the pinmux
register.
Also fix the issue on caluclating pin offset. The last parameter
should be pin number, not register offset.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds support for displaying the individual pin h/w config state.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.
pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:
pmx_dummy: pinmux@4a100040 {
compatible = "pinctrl-single";
reg = <0x4a100040 0x0196>;
#address-cells = <1>;
#size-cells = <0>;
pinctrl-single,register-width = <16>;
pinctrl-single,function-mask = <0x00ff>;
};
&pmx_dummy {
pinctrl-names = "default";
pinctrl-0 = <&board_pins>;
board_pins: pinmux_board_pins {
pinctrl-single,pins = <
0x6c 0xf0f
0x6e 0x10f
0x70 0x23f
0x72 0xa5f
>;
};
};
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one-register-per-pin type device tree based pinctrl driver.
This driver has been tested on omap2+ series of processors,
where there is either an 8 or 16-bit padconf register for each pin.
Support for other similar pinmux controllers can be added.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sachin Kamat