Since the dynamic pin power-control and the analog low-current mode
may lead to pop-noise, it's safer to set it off as default.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=741128
Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VIA codecs have several different power-saving features, and one of
them is the analog low-current mode. But it turned out that the ALC
mode causes pop-noises at each on/off time on some machines. As a
quick workaround, disable the ALC when another power-saving feature,
the dynamic pin power-control, is turned off, too, since the dynamic
power-control is already exposed as a mixer enum element so that user
can turn it on/off freely.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=741128
Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The analog low-current mode must be enabled when the no stream is
running but the current detection checks it in a wrong way.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=741128
Cc: <stable@kernel.org> [v3.1+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of always writing AC_VERB_SET_POWER_STATE, check the current
power-state and don't write again if the value is already set.
This may reduce the click noise upon the dynamic power-state change
(e.g. in analog-input mixer).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit 6584cb88 (ARM i.MX dma: Fix burstsize settings) fixed
the mxcmmc driver but forgot to fix the SDMA driver to handle the
correct burtsize.
This make the SD card access works again with DMA on i.MX31 boards.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
This bug was introduced by commit 54be5663
"gpio-ml-ioh: Support interrupt function" which adds a spinlock to struct
ioh_gpio but never init the spinlock.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit d568a681
"gpio-pch: add spinlock in suspend/resume processing"
which adds a spinlock to struct pch_gpio but never init the spinlock.
Reported-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=3Utr
-----END PGP SIGNATURE-----
Merge tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
firewire fixes post v3.3-rc1
Add workarounds table entries for hardware bugs in
- FireWire part of Sound Blaster Audigy cards,
- Ricoh PCIe 1394 controllers.
Without these, several protocols, e.g. AV/C, do not work on the
Audigy, and the Ricoh PCIe controllers wouldn't work at all.
This does not concern the older Ricoh PCI controllers.
* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: ohci: disable MSI on Ricoh controllers
firewire: ohci: add reset packet quirk for SB Audigy
Add MODULE_LICENSE() as per the license in the comment at the top of the
file for this source module to fix build warning:
WARNING: modpost: missing MODULE_LICENSE() in drivers/staging/media/go7007/go7007-usb.o
see include/linux/module.h for more information
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Ross Cohen <rcohen@snurgle.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix 2 fatal errors in the device-drivers docbook.
Also add some missing files from drivers/base/; since several
of these are DMA-related, add a section for DMA Management.
docproc: drivers/base/sys.c: No such file or directory
docproc: drivers/tty/serial/8250.c: No such file or directory
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As ZTE have and will use more pid for new products this year,
so we need to add some new zte 3g-dongle's pid on option.c ,
and delete one pid 0x0154 because it use for mass-storage port.
Signed-off-by: Rui li <li.rui27@zte.com.cn>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 15c9a0acc3 (of: create of_phandle_args to simplify return of phandle
parsing data) modifies the parameter list of of_xlate function pointer declaration
in gpio_chip. Adapt the gpio specifier translate function for this change.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
lib: Fix 32-bit sparc udiv_qrnnd() definition in mpilib's longlong.h
lib: Fix multiple definitions of clz_tab
lib/digsig: checks for NULL return value
lib/mpi: added missing NULL check
lib/mpi: added comment on divide by 0 case
lib/mpi: check for possible zero length
lib/digsig: pkcs_1_v1_5_decode_emsa cleanup
lib/digsig: additional sanity checks against badly formated key payload
lib/mpi: removed unused functions
lib/mpi: checks for zero divisor length
lib/mpi: return error code on dividing by zero
lib/mpi: replaced MPI_NULL with normal NULL
lib/mpi: added missing NULL check
The usb/ch9.h will be installed to /usr/include/linux,
and be used from user space.
But le16_to_cpu() is only defined for kernel code.
Without this patch, user space compile will be broken.
Special thanks to Stefan Becker
Reported-by: Stefan Becker <chemobejk@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We've found that qcserial devices will not always wake up reliably
from autosuspend, so disable it.
Signed-off-by: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
This copy of longlong.h is extremely dated and results in compile
errors on sparc32 when MPILIB is enabled, copy over the more uptodate
implementation from arch/sparc/math/sfp-util_32.h
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
Both sparc 32-bit's software divide assembler and MPILIB provide
clz_tab[] with identical contents.
Break it out into a seperate object file and select it when
SPARC32 or MPILIB is set.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Morris <jmorris@namei.org>
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=81hM
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
InfiniBand/RDMA fixes for 3.3:
- Fix a crash due to a regression (uninitialized refcnt) introduced in
3.2 with XRC support.
- Close race in how ucma reports events when connect fails.
- Process vendor-specific MADs in mlx4 so that eg FDR-10 data rate works.
- Fix regression in qib caused by over-aggressive PCIe tuning.
- Other small fixes for hardware drivers (ipath, nes, qib).
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Copyright update
IB/mlx4: pass SMP vendor-specific attribute MADs to firmware
RDMA/nes: Fix fast memory registration opcode
RDMA/nes: Fix fast memory registration length
RDMA/ucma: Discard all events for new connections until accepted
IB/qib: Roll back PCIe tuning change
IB/qib: Use GFP_ATOMIC when locks are held
RDMA/nes: Add missing rcu_read_unlock() in nes_addr_resolve_neigh()
RDMA/nes: Fix for sending MPA reject frame
IB/ipath: Calling PTR_ERR() on right variable in create_file()
RDMA/core: Fix kernel panic by always initializing qp->usecnt
Once /proc/pid/mem is opened, the memory can't be released until
mem_release() even if its owner exits.
Change mem_open() to do atomic_inc(mm_count) + mmput(), this only
pins mm_struct. Change mem_rw() to do atomic_inc_not_zero(mm_count)
before access_remote_vm(), this verifies that this mm is still alive.
I am not sure what should mem_rw() return if atomic_inc_not_zero()
fails. With this patch it returns zero to match the "mm == NULL" case,
may be it should return -EINVAL like it did before e268337d.
Perhaps it makes sense to add the additional fatal_signal_pending()
check into the main loop, to ensure we do not hold this memory if
the target task was oom-killed.
Cc: stable@kernel.org
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No functional changes, cleanup and preparation.
mem_read() and mem_write() are very similar. Move this code into the
new common helper, mem_rw(), which takes the additional "int write"
argument.
Cc: stable@kernel.org
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mem_release() can hit mm == NULL, add the necessary check.
Cc: stable@kernel.org
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the SNAPSHOT_CREATE_IMAGE ioctl, if the call to hibernation_snapshot()
fails, the frozen tasks are not thawed.
And in the case of success, if we happen to exit due to a successful freezer
test, all tasks (including those of userspace) are thawed, whereas actually
we should have thawed only the kernel threads at that point. Fix both these
issues.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: stable@vger.kernel.org
My email address has changed, the suse.de one is now dead, so update all
of my MAINTAINER entries with the correct one so that patches don't get
lost.
Also change the status of some of my entries as I'm supposed to be doing
this stuff now for real.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes merge conflict resolution breakage introduced by merge
d3712b9dfc ("Merge tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream").
The commit changed 'mtd_can_have_bb()' function and made it always
return zero, which is incorrect. Instead, we need it to return whether
the underlying flash device can have bad eraseblocks or not. UBI needs
this information because it affects how it handles the underlying flash.
E.g., if the underlying flash is NOR, it cannot have bad blocks and any
write or erase error is fatal, and all we can do is to switch to R/O
mode. We do not need to reserve a pool of good eraseblocks for bad
eraseblocks handling, and so on.
This patch also removes 'mtd_can_have_bb()' invocations from Logfs to
ensure correct Logfs behavior.
I've tested that with this patch UBI works on top of NOR and NAND
flashes emulated by mtdram and nandsim correspondingly.
This patch is based on patch from Linus Torvalds.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Acked-by: Jörn Engel <joern@logfs.org>
Acked-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
serio_raw_read now returns (sometimes partially) successful number of
bytes transferred to the caller, and only returns error code to the
caller on completely failed transfers.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a section which defines the input device properties and provides
guidelines on how to use them.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Chase Douglas <chase.douglas@canonical.com>
Reviewed-by: Jussi Pakkanen <jussi.pakkanen@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A struct device parameter is used in the enable and disable callbacks to
distinguish between different gpio_keys devices.
Platforms that don't use these callbacks may not include struct device
at all, as seen on arch/arm/mach-s3c2410/mach-n30.c
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 509f87c5f5 (evdev - do not block waiting for an event if fd
is nonblock) created a code path were it was possible to use retval
uninitialized.
This could lead to the xorg evdev input driver getting corrupt data
and refusing to work with log messages like
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
AUO-Pixcir touchscreen: Read error: Success
sg060_keys: Read error: Success
(for drivers auo-pixcir-ts and gpio-keys).
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Dima Zavin <dima@android.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a flag to allow platforms to specify, whether a DMAC instance supports
the MEMCPY operation. To avoid regressions, preserve the current default.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Properly set the parent device of DP i2c buses before registering them
too.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The value of this register is transferred to the V_COUNTER register at the
beginning of vertical blank. V_COUNTER is the reference for VLINE waits and
goes from VIEWPORT_Y_START to VIEWPORT_Y_START+VIEWPORT_HEIGHT during scanout,
so if VIEWPORT_Y_START is not 0, V_COUNTER actually went backwards at the
beginning of vertical blank, and VLINE waits excluding the whole scanout area
could never finish (possibly only if VIEWPORT_Y_START is larger than the length
of vertical blank in scanlines). Setting DESKTOP_HEIGHT to the framebuffer
height should prevent this for any kind of VLINE wait.
Fixes https://bugs.freedesktop.org/show_bug.cgi?id=45329 .
CC: stable@vger.kernel.org
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Polling the outputs when the device is suspended can result in erroneous
status updates. Disable output polling during suspend to prevent this
from happening.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
mpi_read_from_buffer() return value must not be NULL.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Comment explains that existing clients do not call this function
with dsize == 0, which means that 1/0 should not happen.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Buggy client might pass zero nlimbs which is meaningless.
Added check for zero length.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Removed useless 'is_valid' variable in pkcs_1_v1_5_decode_emsa(),
which was inhereted from original code. Client now uses return value
to check for an error.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
do_encode_md() and mpi_get_keyid() are not parts of mpi library.
They were used early versions of gnupg and in digsig project,
but they are not used neither here nor there anymore.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Divisor length should not be 0.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
Definitely better to return error code than to divide by zero.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
MPI_NULL is replaced with normal NULL.
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@intel.com>
Reviewed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Morris <jmorris@namei.org>
This typo caused the wrong codec's nid to be checked for wcaps type.
As a result, sometimes speakers would duplicate the output sent to
HDMI output.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/924320
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
K. Y. Srinivasan