Commit Graph

1411 Commits

Author SHA1 Message Date
Bill Pemberton a5023574d1 regulator: remove use of __devinit
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-20 10:31:26 +09:00
Bill Pemberton 5eb9f2b963 regulator: remove use of __devexit_p
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.

Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-20 10:31:19 +09:00
Mark Brown f86221d2b9 Merge branches 'topic/tps51632', 'topic/tps80031', 'topic/vexpress', 'topic/max8925', 'topic/gpio' and 'topic/tps65090' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-hotplug 2012-11-20 10:30:22 +09:00
Laxman Dewangan 5928f53896 regulator: max8973: add regulator driver support
The MAXIM MAX8973 high-efficiency, three phase, DC-DC step-down
switching regulator delievers up to 9A of output current. Each
phase operates at a 2MHz fixed frequency with a 120 deg shift
from the adjacent phase, allowing the use of small magnetic
component.

Add regulator driver for this device.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-19 17:03:11 +09:00
Axel Lin 26cbd30733 regulator: da9055: Fix checking wrong value in da9055_gpio_init
Check pdata->gpio_rsel && pdata->gpio_rsel[id] for the case GPI pin is muxed
with regulator to select the regulator register set A/B for voltage ramping.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-16 09:46:57 +09:00
Laxman Dewangan b92f787d14 regulator: tps80031: add prefix TPS80031 on common defines.
Pefix "TPS80031" is added on all defines of tps80031 header
to avoid conflict with other header definitions.
Update the regualtor driver of tps80031 to use the same name.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-15 14:35:50 +09:00
Ashish Jangam f6130be652 regulator: DA9055 regulator driver
This is the Regulator patch for the DA9055 PMIC and has got dependency on
the DA9055 MFD core.

This patch support all of the DA9055 regulators. The output voltages are
fully programmable through I2C interface only. The platform data with regulation
constraints is passed down from the board to the regulator.

This patch is functionaly tested on SMDK6410 board. DA9055 Evaluation board
was connected to the SMDK6410 board.

Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-15 14:29:49 +09:00
Laxman Dewangan 64e481603a mfd: tps6586x: move regulator dt parsing to regulator driver
Moving regulator node parsing to regulator driver in place
of parsing it on mfd driver.
The motivation for this change are:
- MFD core driver should not depends on regulator and able
  to instantiate device without regulator.
- The API for matching regulators are in regulator core and
  it is good that regulator driver only calls this API.
- Regulator specific support should be in regulator driver only
  to ease any enhancement/modification for regulators.
- The regulator driver is now registered as mfd sub device and
  all regulator registration is done from single probe call.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-15 14:23:17 +09:00
Mark Brown ecb48c337b Merge remote-tracking branches 'regulator/fix/gpio', 'regulator/fix/put' and 'regulator/fix/supp-volt' into tmp 2012-11-15 11:16:02 +09:00
Marek Szyprowski f0f98b19e2 regulator: fix voltage check in regulator_is_supported_voltage()
regulator_is_supported_voltage() should return true only if the voltage
of fixed/constant regulator is between min_uV and max_uV.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
2012-11-15 11:14:18 +09:00
Lee Jones 216f2b9c95 regulator: gpio-regulator: Catch 'no states property' misuse
A selection of voltage or current values (AKA states) should always
be specified when using a GPIO regulator. If there are no switchable
states then the fixed regulators should be used instead.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-14 20:58:09 +09:00
Charles Keepax 23ff2f0f61 regulator: core: Avoid deadlock when regulator_register fails
When regulator_register fails and exits through the scrub path the
regulator_put function was called whilst holding the
regulator_list_mutex, causing deadlock.

This patch adds a private version of the regulator_put function which
can be safely called whilst holding the mutex, replacing the
aforementioned call.

Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-14 19:01:15 +09:00
Frank Li f8a9f757cb regulator: gpio-regulator: fix can't find regulator node in dt
Need initilize of_node in regulator config when register regulator,
otherwise regulator driver think it is no-dt device.

in regulator_dev_lookup
list_for_each_entry(r, &regulator_list, list)
	if (r->dev.parent &&
		node == r->dev.of_node)
			return r

r->dev.of_noe will be zero if miss config in cfg.

Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-13 16:35:57 +09:00
Laxman Dewangan 1a0bb679bc regulator: tps80031: add regulator driver for tps80031
Add regulator driver for Texas Instrument TPS80031/TPS80032 device.
TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. It has 5 configurable step-down
converters, 11 general purpose LDOs, VBUS generator and digital
output to control regulators.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-13 15:57:39 +09:00
Qing Xu 45b6f8e8fc regulator: max8925: support dt for regulator
Signed-off-by: Qing Xu <qingx@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-07 15:12:12 +01:00
Axel Lin 7bde76726f regulator: tps51632: Fix trivial typo for TPS51632 Kconfig help text
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-11-01 14:23:04 +00:00
Andrew Lunn b2da55d944 Regulator: core: Unregister when gpio request fails.
If the gpio_request_one() fails, or returns EPROBE_DEFER, the
regulator must be device_unregister()ed. When this is not done,
there are WARNING: from sysfs:

WARNING: at fs/sysfs/file.c:343 sysfs_open_file+0x238/0x268()

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-28 18:13:07 +00:00
Yadwinder Singh Brar 38d34035e6 regulator: max77686: Make max77686_enable() static.
This patch fixes a sparse warning. Since max77686_enable() is a callback,so it
should be static.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-22 14:55:36 +01:00
Lee Jones 006694d099 regulator: gpio-regulator: Allow use of GPIO controlled regulators though DT
Here we provide the GPIO Regulator driver with Device Tree capability, so
that when a platform is booting with DT instead of platform data we can
still make full use of it.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:27:55 +09:00
Laxman Dewangan f329b1755b regulator: tps65090: add external control support for DCDC
The TPS65090's DCDC output can also be enable/disable through the
external digital input signal. Add support for enable/disable
either through register access via I2C or through external
control inputs. The external control inputs can be driven through
GPIOs also and hence adding support for passing the GPIO number.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:21:21 +09:00
Laxman Dewangan 3a81ef8c27 regulator: tps65090: Add support for LDO regulators
TPS65090 supports the two LDOs, LDO1 and LDO2. These are
always ON regulators. The output on these LDOs are available
once the input voltage available for these LDOs.
Add support for these LDOs regulators.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:21:20 +09:00
Laxman Dewangan 8620ca9f77 regulator: tps65090: rename driver name and regulator name
To make the names proper and more appropriate:
Rename the driver name from tps65090-regulator to tps65090-pmic.
Rename the regulators from TPS65090_ID_* to TPS65090_REGULATOR_*

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:21:20 +09:00
Laxman Dewangan 24282a1ca3 regulator: tps65090: Register all regulators in single probe call
MFD driver registers the regulator driver once per device and
hence it is require to register all regulators in single probe
call.
Following are details of changes done to achieve this:
- Move the regulator enums to mfd header and remove the
  tps65090-regulator.h as it does not contain more info.
- Add max regulator and register all regulators even if there
  is no regulator init data from platform.
- Convert regulator init data to pointer type in platform data.
- Add input supply name in regulator desc to provide input supply.
- Separate desc information from driver information.
- Disable external control bit to have control through register write.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:21:14 +09:00
AnilKumar Ch a9a5659ac6 regulator: tps65910: fix BUG_ON() shown with vrtc regulator
Fix BUG_ON() error if tps65910 VRTC regulator is used with out
rdev->desc->volt_table data. Recent changes in regulator core driver
which add support for "regulator_list_voltage_table" have BUG_ON() if
regulator descriptor do not voltage table information. This patch adds
the voltage table information to fix the issue.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:17:39 +09:00
Yadwinder Singh Brar 15282ba9ea regulator: max77686: Add set_suspend_disable/set_suspend_mode callbacks.
This patch implements set_suspend_disable callback for BUCKs which
support only switch ON/OFF modes during system suspend state, and
set_suspend_mode callbacks for LDOs which also suport Low power mode and
switch ON/OFF modes.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:16:21 +09:00
Yadwinder Singh Brar 6d2c896b72 regulator: max77686: Use already set opmode while re-enabling regulators.
This patch adds basic support to take care of opmode(if any) which can be set by
set_suspend_[disable/mode] callbacks.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 22:16:21 +09:00
Axel Lin 9f4e45f77e regulator: vexpress: Add terminating entry for vexpress_regulator_of_match table
The of_device_id table is supposed to be zero-terminated.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-17 16:34:08 +09:00
Pawel Moll 31e54086dd regulator: Versatile Express regulator driver
Implementation of the regulator framework driver for the
Versatile Express voltage control. Devices without
voltage constraints (ie. "regulator-[min|max]-microvolt"
properties in the DT node) are treated as fixed (or rather
read-only) regulators.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:56:08 +09:00
Pawel Moll bd7a2b600a regulator: core: Support for continuous voltage range
Some regulators can set any voltage within the constraints range,
not being limited to specified operating points.

This patch makes it possible to describe such regulator and makes
the regulator_is_supported_voltage() function behave correctly.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:56:08 +09:00
Laxman Dewangan 0c57067430 regulator: tps51632: Add tps51632 regulator driver
The TPS51632 is a driverless step down controller with
serial control. Advanced features such as D-Cap+
architecture with overlapping pulse support and OSR
overshoot reduction provide fast transient response,
lowest output capacitance and high efficiency.
The TPS51632 supports both I2C and DVFS interfaces
(through PWM) for dynamic control of the output voltage
and current monitor telemetry.
Add regulator driver for TPS51632.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 11:54:42 +09:00
Mark Brown 4e92920b4b regulator: lp8788-ldo: Staticise non-exported symbol
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-10-15 10:06:44 +09:00
Linus Torvalds 578f1ef91a MFD bits for the 3.7 merge window.
As usual we have a few new drivers:
 
 - TI LP8788
 - TI OMAP USB TLL
 - Maxim MAX8907
 - SMSC ECE1099
 - Dialog Semiconductor DA9055
 - A simpler syscon driver that allow us to get rid of the anatop one.
 
 Drivers are also gradually getting Device Tree and IRQ domain support.
 
 The following drivers got DT support:
 - palmas, 88pm860x, tc3589x and twl4030-audio
 
 And those ones now use the IRQ domain APIs:
 - 88pm860x, tc3589x, db8500_prcmu
 
 Also some other interesting changes:
 - Intel's ICH LPC now supports Lynx Point
 - TI's twl4030-audio added a GPO child
 - tps6527 enabled its backlight subdevice
 - The twl6030 pwm driver moved to the new PWM subsystem
 
 And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x, palmas,
 ab8500, wm8994, wm5110, max8907 and the tps65xxx family.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQbVq4AAoJEIqAPN1PVmxKXOsP/ifwoqYkaGUsZ7M8b8iTTxlk
 a0/SBU1O+FDG7LbIsOyJ6VZCpipj8R4WyVqNdS2CSPVoSdT8KnakrxFY9FAtcmpA
 c6O7r+9dymcT7HeQ6mBQYYeEyXcZQkTXj9Y298zuRT88gccH5PQIOX8DTj6gKVxN
 xhuDuAWtizvwAJWfof/57p7JLilCF96Hq0UdeISD10UWJPxPmXFJTzzYw6GbPPOl
 zk1N6yig3VpK6sfK+QdqZykHFKj23RX57SmceHOISTpEr66ayuKIkJEqWm/IydMO
 XWDTT2IN80ca+1PnbrQOyiMtXg3EKrZN5WDEp2AcUiKP0fnAoZBTeuZUkqyLc3rJ
 W8LowQe6x5154CeLwcJc4+kmeGUhbj09GHKCsI7x/lQpMWgJCaGHGvLxAUE1uRZi
 4Bn9IUP7OqE465fNolLOd1fRxgzWJxe5rBYKQB7UcOrS0NThPhu0r0qV905zBrBO
 tyCZz+PexTiirpbv1K0dMTcpWeHVOmtYG5uJTmw9wTRv7jW7aUhkhkW5Q+E5BAdb
 9Rj5/vYertqI3VzRQ1w2z1SavzBO3OykTURWGDkwjfFWYbJtEdPYGGjRSFiphVYG
 8jvs5UzrDm2ICqkpkKzovVWi9lXyvNVVCgSwxHQeoPXfqb5dXLlbUZZBaCaQpRII
 XlItAJvIiUNIA8bXLoC8
 =n6lp
 -----END PGP SIGNATURE-----

Merge tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull MFD changes from Samuel Ortiz:
 "MFD bits for the 3.7 merge window.

  As usual we have a few new drivers:

   - TI LP8788
   - TI OMAP USB TLL
   - Maxim MAX8907
   - SMSC ECE1099
   - Dialog Semiconductor DA9055
   - A simpler syscon driver that allow us to get rid of the anatop one.

  Drivers are also gradually getting Device Tree and IRQ domain support.

  The following drivers got DT support:
   - palmas, 88pm860x, tc3589x and twl4030-audio

  And those ones now use the IRQ domain APIs:
   - 88pm860x, tc3589x, db8500_prcmu

  Also some other interesting changes:
   - Intel's ICH LPC now supports Lynx Point
   - TI's twl4030-audio added a GPO child
   - tps6527 enabled its backlight subdevice
   - The twl6030 pwm driver moved to the new PWM subsystem

  And finally a bunch of cleanup and casual fixes for mc13xxx, 88pm860x,
  palmas, ab8500, wm8994, wm5110, max8907 and the tps65xxx family."

Fix up various annoying conflicts: the DT and IRQ domain support came in
twice and was already in 3.6. And then it was apparently rebased.

Guys, DON'T REBASE!

* tag 'mfd-3.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (89 commits)
  ARM: dts: Enable 88pm860x pmic
  mfd: 88pm860x: Move gpadc init into touch
  mfd: 88pm860x: Device tree support
  mfd: 88pm860x: Use irqdomain
  mfd: smsc: Add support for smsc gpio io/keypad driver
  backlight: tps65217_bl: Add missing platform_set_drvdata in tps65217_bl_probe
  mfd: DA9055 core driver
  mfd: tps65910: Add alarm interrupt of TPS65910 RTC to mfd device list
  mfd: wm5110: Add register patches for revision B
  mfd: wm5110: Disable control interface error report for WM5110 rev B
  mfd: max8907: Remove regulator-compatible from DT docs
  backlight: Add TPS65217 WLED driver
  mfd: Add backlight as subdevice to the tps65217
  mfd: Provide the PRCMU with its own IRQ domain
  mfd: Fix max8907 sparse warning
  mfd: Add lp8788 mfd driver
  mfd: dbx500: Provide a more accurate smp_twd clock
  mfd: rc5t583: Fix warning messages
  regulator: palmas: Add DT support
  mfd: palmas: Change regulator defns to better suite DT
  ...
2012-10-05 12:01:30 +09:00
Linus Torvalds 033d9959ed Merge branch 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
Pull workqueue changes from Tejun Heo:
 "This is workqueue updates for v3.7-rc1.  A lot of activities this
  round including considerable API and behavior cleanups.

   * delayed_work combines a timer and a work item.  The handling of the
     timer part has always been a bit clunky leading to confusing
     cancelation API with weird corner-case behaviors.  delayed_work is
     updated to use new IRQ safe timer and cancelation now works as
     expected.

   * Another deficiency of delayed_work was lack of the counterpart of
     mod_timer() which led to cancel+queue combinations or open-coded
     timer+work usages.  mod_delayed_work[_on]() are added.

     These two delayed_work changes make delayed_work provide interface
     and behave like timer which is executed with process context.

   * A work item could be executed concurrently on multiple CPUs, which
     is rather unintuitive and made flush_work() behavior confusing and
     half-broken under certain circumstances.  This problem doesn't
     exist for non-reentrant workqueues.  While non-reentrancy check
     isn't free, the overhead is incurred only when a work item bounces
     across different CPUs and even in simulated pathological scenario
     the overhead isn't too high.

     All workqueues are made non-reentrant.  This removes the
     distinction between flush_[delayed_]work() and
     flush_[delayed_]_work_sync().  The former is now as strong as the
     latter and the specified work item is guaranteed to have finished
     execution of any previous queueing on return.

   * In addition to the various bug fixes, Lai redid and simplified CPU
     hotplug handling significantly.

   * Joonsoo introduced system_highpri_wq and used it during CPU
     hotplug.

  There are two merge commits - one to pull in IRQ safe timer from
  tip/timers/core and the other to pull in CPU hotplug fixes from
  wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."

Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.

Tejun pointed out a few of them, I fixed a couple more.

* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
  workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
  workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
  workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
  workqueue: remove @delayed from cwq_dec_nr_in_flight()
  workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
  workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
  workqueue: use __cpuinit instead of __devinit for cpu callbacks
  workqueue: rename manager_mutex to assoc_mutex
  workqueue: WORKER_REBIND is no longer necessary for idle rebinding
  workqueue: WORKER_REBIND is no longer necessary for busy rebinding
  workqueue: reimplement idle worker rebinding
  workqueue: deprecate __cancel_delayed_work()
  workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
  workqueue: use mod_delayed_work() instead of __cancel + queue
  workqueue: use irqsafe timer for delayed_work
  workqueue: clean up delayed_work initializers and add missing one
  workqueue: make deferrable delayed_work initializer names consistent
  workqueue: cosmetic whitespace updates for macro definitions
  workqueue: deprecate system_nrt[_freezable]_wq
  workqueue: deprecate flush[_delayed]_work_sync()
  ...
2012-10-02 09:54:49 -07:00
Haojian Zhuang 2e57d56747 mfd: 88pm860x: Device tree support
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-10-02 11:43:13 +02:00
Mark Brown 6a2027abd2 Merge remote-tracking branches 'regulator/topic/core', 'regulator/topic/bypass', 'regulator/topic/tol', 'regulator/topic/drivers' and 'regulator/topic/tps6586x' into regulator-next 2012-09-28 14:45:07 +01:00
Mark Brown e96961dabe regulator: arizona-ldo: Remove top voltage
The highest voltage step is not supported.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-28 14:44:11 +01:00
Stephen Warren 13511def87 regulator: deprecate regulator-compatible DT property
When the bindings for the TPS6586x regulator were being proposed, I
asserted that DT node naming rules for bus child nodes should also be
applied to nodes inside the TPS6586x regulator node itself. In other
words, that each node providing regulator init data should be named
after the type of object it represented ("regulator") and hence that
some other property was required to indicate which regulator the node
described ("regulator-compatible"). In turn this led to multiple nodes
having the same name, thus requiring node names to use a unit address
to make them unique, thus requiring reg properties within the nodes and

However, subsequent discussion indicates that the rules I was asserting
only applies to standardized bus nodes, and within a device's own node,
the binding can basically do anything sane that it wants.

Hence, this change deprecates the register-compatible property, and
instead uses node names to replace this functionality. This greatly
simplifies the device tree content, making them smaller and more legible.

The code is changed such that old device trees continue to work.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-25 13:44:47 +01:00
Graeme Gregory a361cd9f2e regulator: palmas: Add DT support
Add DT support to palmas regulator. This involved a little change to
the platform data structure. Regulator information can now come from
platform data or DT.

Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-23 20:51:33 +02:00
Haojian Zhuang ff13e9e256 mfd: 88pm860x: Avoid to check resource for preg regulator
Since PREG regulator is the only one regulator in 88PM8606, and other
regulators are in 88PM8607. Checking resource as identifying regulator
is not a good way. We can use NULL resource to indentify PREG regulator.

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-19 12:39:13 +02:00
Jett.Zhou e7a7810ae0 regulator: 88pm860x: Add pre-regulator support for 88pm860x regulator
Pre-regulator of 88pm8606 is mainly for support charging based on vbus,
it needs to be enabled for charging battery, and will be disabled in
some exception condition like over-temp.
Add the pre-regulator support for 88pm860x regulator driver.

Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-19 12:39:13 +02:00
Haojian Zhuang 51acdb6118 mfd: max8925: Remove array in regulator platform data
Remove array in parent's platform data. Use struct regulator_init_data
as regulator device's platform data directly. So a lot of pdata are
added into parent's platform data. And voltage out register offset
is used as IORESOURCE_REG to distinguish different regualtor devices.

Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-19 12:39:13 +02:00
Dong Aisheng baa64151ae regulator: anatop-regulator: Convert to use syscon to access anatop register
Using syscon to access anatop register.

Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-17 15:27:31 +02:00
Linus Torvalds 73f8be297e This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
 - A lcp_ich regression fix caused by the MFD driver failing to initialize the
   watchdog sub device due to ACPI conflicts.
 - 2 MAX77693 interrupt handling bug fixes.
 - An MFD core fix, adding an IRQ domain argument to the MFD device addition
   API in order to prevent silent and potentially harmful remapping behaviour
   changes for drivers supporting non-DT platforms.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQVQpwAAoJEIqAPN1PVmxKpnQP/iDPakfGT0m00nxk9VvuXfaA
 SlNxhhM1ZPxlZcBrVFULZ+dCVuUaBYIfwoT4Wwl2yZsmp8uYb62Rd6LGXDnjO+FH
 zKMg3b/KDHq/jicYxqFy4bVq3I850jTLN4Hti6hArn8HM6gxZJQxM810Poxt6M0T
 odud6oHSevGpCoL7GU4O+gmx1wKSDRrw6TZPokJDfXaQcFPJEt0YGGtI2zAO1sV+
 iBPQE/bI3bF5r/kowbh9ro5WybGNyFrwiYtaTzJWntXoPKN1lmr0F2F2NaCEo1xj
 2vJPFSCK3qC9Ft7sPQEBYxrSXzyzgu7G8HGgkcBG5SaSo+W3awe9DEaHfk5E7sdr
 iyc01kh4FmGlMAvHG/zcK3YvchR7GJdRI7BrR+MTQ03ZUv/ZrmTYFAHv5fAzBQ+N
 6ZUoC/1bqPKpfeFPOKYpDeYJVnFBWLYr+t7McTqqg+kpxUuYnQ0HyJVjDh01ZVQT
 AtCjjW7R+Ka44B+xfMOartPZMqZZEHSJ0UjacyEyzMpAAY14eUDMtTqs/jtNp+8Z
 B0bZiA8ZhUmNVH7TZoT/u57FgEW34JnM8oH6jLVN+yjInpuugIvqpZn0TA90GL7V
 Fh2DALMgUN5z/TXduGSsSPg1hvXFPOujaS+4o78e8PWiVQd5XUk/mc8OOS/mrRwj
 +mILnzxJcp8iYrYqESbt
 =nP/y
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull mfd fixes from Samuel Ortiz:
 "This is the remaining MFD fixes for 3.6, with 5 pending fixes:

   - A tps65217 build error fix.
   - A lcp_ich regression fix caused by the MFD driver failing to
     initialize the watchdog sub device due to ACPI conflicts.
   - 2 MAX77693 interrupt handling bug fixes.
   - An MFD core fix, adding an IRQ domain argument to the MFD device
     addition API in order to prevent silent and potentially harmful
     remapping behaviour changes for drivers supporting non-DT
     platforms."

* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: MAX77693: Fix NULL pointer error when initializing irqs
  mfd: MAX77693: Fix interrupt handling bug
  mfd: core: Push irqdomain mapping out into devices
  mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
  mfd: Move tps65217 regulator plat data handling to regulator
2012-09-16 13:22:21 -07:00
Marcus Cooper 0fd0013cda mfd: ab3100: Split ab3100 headers out of abx500.h
The U8500 has its own set of separate header, so the abx500
becomes completely abstract. Do the same split for the AB3100
legacy ASIC.

Signed-off-by: Marcus Cooper <marcus.xm.cooper@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-14 09:52:15 +02:00
Haojian Zhuang a70abacb06 mfd: 88pm860x: Use REG resource in regulator
Since IORESOURCE_IO is changed to IORESOURCE_REG in 88pm860x driver,
update self-defined IORESOURCE_IO resource to register offset that
is IORESOURCE_REG in regulator driver. And split regulator platform
data array into scattered platform data.

Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-11 11:38:17 +02:00
Mark Brown 023670295a mfd: 88pm860x: Convert to IORESOURCE_REG
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-11 10:15:03 +02:00
Mark Brown 5656098e19 mfd: wm831x: Convert to IORESOURCE_REG
This was originally written by Russell King who unfortunately found
himself unable to take the patch futher.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Tested-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-11 10:15:03 +02:00
Yunfan Zhang 3b26e48308 regulator: fan53555: remove vsel_max not used
The max voltage will be bounded by min_uV, uV_step and n_voltages, so
remove it to avoid confusing.

Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 15:58:01 +08:00
Mark Brown e4c5288e41 regulator: aat2870: Don't explicitly initialise the first field
Doing so generates a warning as the first field is a pointer but we use
0 to initalize it.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 15:34:36 +08:00
Mark Brown 22c5fb6a7d regulator: wm831x-ldo: Add bypass support
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 11:25:13 +08:00
Mark Brown e477ce075d regulator: arizona-micsupp: Support get/set bypass
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 11:25:12 +08:00
Mark Brown 9a17de04ef regulator: arizona-ldo: Support get/set bypass
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 11:25:11 +08:00
Mark Brown df36793115 regulator: core: Provide regmap get/set bypass operations
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 11:25:10 +08:00
Mark Brown f59c8f9fe6 regulator: core: Support bypass mode
Many regulators support a bypass mode where they simply switch their
input supply to the output. This is mainly used in low power retention
states where power consumption is extremely low so higher voltage or
less clean supplies can be used.

Support this by providing ops for the drivers and a consumer API which
allows the device to be put into bypass mode if all consumers enable it
and the machine enables permission for this.

This is not supported as a mode since the existing modes are rarely used
due to fuzzy definition and mostly redundant with modern hardware which is
able to respond promptly to load changes.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Graeme Gregory <gg@slimlogic.co.uk>
2012-09-10 11:25:10 +08:00
Yunfan Zhang 49d8c59927 regulator: Fairchild fan53555 support
This driver supports Fairchild FAN53555 Digitally Programmable
TinyBuck Regulator. The FAN53555 is a step-down switching voltage
regulator that delivers a digitally programmable output from an
input voltage supply of 2.5V to 5.5V. The output voltage is
programmed through an I2C interface.

Signed-off-by: Yunfan Zhang <yfzhang@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-10 09:55:22 +08:00
Mark Brown 029dd3cefa regulator: twl: Remove another unused variable warning
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-09 11:09:38 +08:00
AnilKumar Ch 52b84dac43 regulator: core: Try using the parent device for the default regmap
If the device doesn't have a regmap specified by the driver and we can't
find one on the device itself try its parent, providing a useful defualt
for many MFDs.

[Rewrite commit message -- broonie]

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-08 08:54:15 +08:00
Mark Brown 2b5a24a01d regulator: core: Fast path non-deferred disables
Users (especially framework code) may end up passing in a zero deferral
time depending on runtime conditions or configuration. If they do then
just call regulator_disable() directly to save scheduling.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2012-09-08 08:51:12 +08:00
Mark Brown f2889e650a regulator: core: Report microvolts in sysfs even with only list_voltage()
If a regulator only supports a single voltage list_voltage() can be used
to report what that voltage is so add this as one of the criteria for
creating the microvolts file in sysfs.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-07 09:48:15 +08:00
Laxman Dewangan 9394b80c35 regulator: tps6586x: add support for SYS rail
Device have SYS rail which is always ON. It is system power bus. LDO5
and LDO_RTC get powered through this rail internally. Add support for
this rail and make the LDO5/LDO_RTC supply by it. Update document
accordingly.

[swarren: Instantiate the sys regulator from board-harmony-power.c to
 avoid regression.]

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 07:57:00 +08:00
Kim, Milo 5bab305d3c regulator: lp872x: remove unnecessary function
The lp872x_check_dvs_validity() is used for checking DVS platform data.
 If the DVS platform data is not defined, return as error code.
 Now, this is unnecessary because the default DVS mode is set in this case.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 07:53:03 +08:00
Kim, Milo 9d6da6fcc2 regulator: lp872x: fix NULL pointer access problem
The lp872x_set_dvs() is used for changing the DVS pin state.
 This function works only when the DVS platform data is defined.
 So don't assume that DVS data is always valid.
 In case the platform data is not defined, the DVS data is set to NULL
 for skipping the DVS pin control.

 DVS selection and GPIO pin number are used for the LP872x DVS pin control.
 For better readability, DVS selection argument is added in lp872x_set_dvs().

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 07:53:02 +08:00
Kim, Milo 86b3fef0c7 regulator: lp872x: initialize the DVS mode
The platform specific configuration(general_config) is optional.
 However, the DVS settings should be configured explicitly while
 loading the driver.
 This patch enables configuring the default DVS mode even though
 the platform data is not defined.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 07:53:02 +08:00
Kim, Milo b158fba605 regulator: lp872x: set the default DVS mode
The lp872x driver has the DVS platform data which select the register address
 of the BUCK voltage.
 This patch enables updating the default DVS mode when the DVS platform data
 is not defined.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 07:53:02 +08:00
Kim, Milo 9ffaa8689e regulator: lp872x: remove regulator platform data dependency
This patch enables registering the regulator driver even though
 the regulator_init_data is not defined in the platform side.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-09-06 07:53:02 +08:00
Gaëtan Carlier ba02dfd205 regulator: mc13783: add regulators sw1x and sw2x
Signed-off-by: Gaëtan Carlier <gcembed@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:30 -07:00
Axel Lin d154f0a617 regulator: max8907: Add MODULE_ALIAS
This driver can be built as a module, add MODULE_ALIAS for it.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:30 -07:00
Stephen Warren 5fc72f57e6 regulator: max8907: fix use of possibly NULL idata
If a regulator is not used by a board, it's quite legitimate not to
provide platform data or a device tree node to configure it (i.e.
regulator_init_data). In that case, during MAX8907 regulator's
probe(), the idata variable will be NULL for that regulator. Prevent
dereferincing it.

If the MBATT regulator's init_data is not specified, or no name was
specified in the constraints, the regulator will be named based on
the regulator descriptor, so initialize mbatt_rail_name from there.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:30 -07:00
Randy Dunlap dedae957a4 regulator: fix kernel-doc warnings in drivers/regulator/core.c
Fix regulator kernel-doc warnings:

Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc:	Liam Girdwood <lrg@ti.com>
Cc:	Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:30 -07:00
Linus Walleij a0a7014cd4 regulator: ab8500: provide per-regulator shift
This encodes the voltage shifts (the number of bits to shift
the register to get to the selector) into the regulator info.
We have several new variants of the AB8500 so this varies a
lot.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:30 -07:00
Stephen Warren db55168265 regulator: max8907: fix compile error when !CONFIG_OF
Fix the following:

  CC [M]  drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_probe':
drivers/regulator/max8907-regulator.c:297:12: error: 'max8907_matches' undeclared (first use in this function)

by removing direct references to max8907_matches[], which only exists when
CONFIG_OF is defined.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:29 -07:00
Axel Lin 0764ef5916 regulator: max8907: Properly set pmic pointer in max8907_regulator_remove()
Add missing platform_get_drvdata() call in max8907_regulator_remove(), this
fixes below build warning:

  CC [M]  drivers/regulator/max8907-regulator.o
drivers/regulator/max8907-regulator.c: In function 'max8907_regulator_remove':
drivers/regulator/max8907-regulator.c:353:23: warning: 'pmic' is used uninitialized in this function [-Wuninitialized]

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:29 -07:00
Axel Lin 7305608bc8 regulator: max8907: Fix n_voltages for MAX8907B SD1
For linear voltage mapping, the n_voltages is (max - min) / step + 1

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:28 -07:00
Stephen Rothwell 8f52a5800a regulator: using kfree() requires including slab.h
Fixes this build error:

drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1229:3: error: implicit declaration of function 'kfree' [-Werror=implicit-function-declaration]

Also added string.h for kmemdup().

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:28 -07:00
Gyungoh Yoo ffee19091a regulator: add MAX8907 driver
The MAX8907 is an I2C-based power-management IC containing voltage
regulators, a reset controller, a real-time clock, and a touch-screen
controller.

The original driver was written by:
* Gyungoh Yoo <jack.yoo@maxim-ic.com>

Various fixes and enhancements by:
* Jin Park <jinyoungp@nvidia.com>
* Tom Cherry <tcherry@nvidia.com>
* Prashant Gaikwad <pgaikwad@nvidia.com>
* Dan Willemsen <dwillemsen@nvidia.com>
* Laxman Dewangan <ldewangan@nvidia.com>

During upstreaming, I (swarren):
* Converted to regmap.
* Allowed probing from device tree.
* Reworked the regulator driver to be represented as a single device that
  provides multiple regulators, rather than as a device per regulator.
* Replaced many regulator ops with standard functions.
* Added ability to specify supplies for each regulator.
* Removed the WLED regulator. If/when we expose this in the driver, it
  should be a backlight object not a regulator object.
* Renamed from max8907c->max8907, since the driver covers at least the
  C and B revisions.
* General cleanup.

Signed-off-by: Gyungoh Yoo <jack.yoo@maxim-ic.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:28 -07:00
Arnd Bergmann 0ffff5a60f regulator: twl: make twl_info tables const
I currently carry the series to make of_device_id->data const in the
arm-soc tree, which fixes a number of issues, but leaves one new
compiler warning about the twl-regulator driver:

drivers/regulator/twl-regulator.c: In function 'twlreg_probe':
drivers/regulator/twl-regulator.c:1130:8: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]
drivers/regulator/twl-regulator.c:1139:9: warning: assignment discards 'const'
qualifier from pointer target type [enabled by default]

The warning indicates that the driver takes a static table with
initialization data for each regulator, modifies the data in place
and passes a pointer to that structure to the regulator_register
function. This is probably ok because a system contains only one
instance of each regulator, but it's still bad style because any
driver should be written to support multiple instances of the same
hardware.

This patch changes the code to dynamically allocate the memory
we pass to the regulator core so the table can be constant.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:28 -07:00
Axel Lin f9cfbde723 regulator: twl: Remove get_voltage implementation for single voltage regulators
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:28 -07:00
Axel Lin 9c7fde4e80 regulator: isl6271a: Remove get_voltage implementation for isl_fixed_ops
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:27 -07:00
Axel Lin 0d3fb582dc regulator: ab8500: Remove get_voltage implementation for ab8500_regulator_fixed_ops
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:27 -07:00
Axel Lin 88348effd6 regulator: ab3100: Remove get_voltage implementation for regulator_ops_fixed
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:27 -07:00
Axel Lin b571dc38d4 regulator: mc13xxx: Remove get_voltage implementation for single voltage regulators
This is not required after commit f7df20ec
"regulator: core: Use list_voltage() to read single voltage regulators"

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:27 -07:00
Axel Lin 19d23c21a6 regulator: da9052: set_current_limit should select the maximum current in specific range
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:26 -07:00
Axel Lin 4e1d67eddf regulator: lp872x: set_current_limit should select the maximum current in specific range
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:26 -07:00
Axel Lin 73f4f3d376 regulator: tps6524x: set_current_limit should select the maximum current in specific range
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:26 -07:00
Axel Lin 422294deee regulator: wm831x-dcdc: set_current_limit should select the maximum current in specific range
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:26 -07:00
Axel Lin cb44cdeacd regulator: max77686: Use array to save pointer to rdev
MAX77686_REGULATORS is known in compile time.
Use array to save pointer to rdev makes the code simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:26 -07:00
Axel Lin 2c58e2669f regulator: max77686: initialize of_node param for regulator register
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:25 -07:00
Axel Lin 7fee2afb53 regulator: ab8500: Set enable enable_time in regulator_desc
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:25 -07:00
Axel Lin 4001376ef2 regulator: wm8400: Simplify set REGULATOR_MODE_IDLE mode in wm8400_dcdc_set_mode
To set REGULATOR_MODE_IDLE mode, what we do is to clear DC1_ACTIVE and
DC1_SLEEP bits, this can be done in one wm8400_set_bits() call.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:25 -07:00
Axel Lin 363506cd71 regulator: wm831x-ldo: Check return value of wm831x_reg_read()
wm831x_reg_read() returns negative error code on failure.
This prevents using the error code as the value read.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:25 -07:00
Axel Lin 7c7475c009 regulator: tps6586x: Convert to regulator_[enable|disable|is_enabled|get_voltage_sel]_regmap
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:25 -07:00
Axel Lin 0f4c46d2e2 regulator: Use BUCK_FPWM_[MASK|SHIFT] macros to replace buck_pmap table
Below is the buck_pmap mapping table:

BUCK1:  mask = 1 << 0,  shift = 0
BUCK2:  mask = 1 << 1,  shift = 1
BUCK3:  mask = 1 << 2,  shift = 2
BUCK4:  mask = 1 << 3,  shift = 3

The mask and shift can be easily calculated by:
        mask = 1 << BUCK_ID
        shift = BUCK_ID

This patch defines BUCK_FPWM_MASK and BUCK_FPWM_SHIFT macros to replace
buck_pmap mapping table.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin c42ea5cdfb regulator: lp8788-buck: Remove lp8788_set_default_dvs_ctrl_mode function
We already know the mask in lp8788_init_dvs() function, and we can update
the corresponding bit for default_dvs_mode in lp8788_init_dvs() function.
This function looks not necessary to me.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin 74c8cfdaa6 regulator: lp8788-ldo: Set n_voltages to 1 for fixed voltage
For fixed voltage, the n_voltages should be 1 rather than 0.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin f1dcf9e4ed regulator: mc13892: Convert mc13892_sw_regulator_ops to get_voltage_sel
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin 8db98440fa regulator: mc13892: Simplify implementation of mc13892_sw_regulator_set_voltage_sel()
Use mc13xxx_reg_rmw rather than a mc13xxx_reg_read and a mc13xxx_reg_write calls.

This logic to set MC13892_SWITCHERS0_SWxHI bit is pretty simple:

if (volt > 1375000)
        set MC13892_SWITCHERS0_SWxHI bit
else if (volt < 1100000)
        clear MC13892_SWITCHERS0_SWxHI bit
else
        leave MC13892_SWITCHERS0_SWxHI bit untouched

We already know the selector, so we don't need to calculate the selector again.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:24 -07:00
Axel Lin 825d105910 regulator: mc13892: Make mc13892_powermisc_rmw() lock protected
Then we can remove lock/unlock around the caller.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:23 -07:00
Axel Lin 2a2c3ac0a5 regulator: mc13783: Make mc13783_powermisc_rmw() lock protected
Then we can remove lock/unlock around the caller.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:16 -07:00
Axel Lin 4a247a961a regulator: palmas: Convert palmas_ops_ldo to [get|set]_voltage_sel_regmap
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:16 -07:00
Axel Lin 38f8f43cba regulator: twl: Convert twlsmps_ops to get_voltage_sel and map_voltage
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:16 -07:00
Axel Lin 78292f4ed2 regulator: twl: Fix checking voltage range in twl6030smps_set_voltage()
The voltage selection logic is supposed to find the samllest voltage falls
within specified range. When using equation to calculate vsel, we need to
ensure the requested min_uV meet the range of using the equation.
Otherwise we may select a voltage that is out of specified range.

For example, in the case vsel = 62 means select voltage of 2100000uV.
What we want is to ensure the requested min_uV <= 2100000 rather than checking
max_uV >= 2100000. And this also means in the case min_uV > 2100000, vsel = 62
does not meet the request.

Also calling twl6030smps_list_voltage() for all cases to ensure the selected
voltage still in bounds.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:15 -07:00
Axel Lin 13407ea802 regulator: mc13xxx: Populate selector from mc13xxx_fixed_regulator_set_voltage
This was missing until now and the underlying
_regulator_do_set_voltage is using this value when calling list_voltage.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:15 -07:00
Axel Lin ad46ed14ca regulator: s2mps11: Use array to save pointer to rdev
The number of regulator is known at compile time, use array to save pointer to
rdev makes the code simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-28 11:00:15 -07:00
AnilKumar Ch 1922b0f275 mfd: Move tps65217 regulator plat data handling to regulator
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.

This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.

drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'

This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
2012-08-22 10:55:25 +02:00
AnilKumar Ch 817bb7fbfb mfd: Move tps65217 regulator plat data handling to regulator
Regulator platform data handling was mistakenly added to MFD
driver. So we will see build errors if we compile MFD drivers
without CONFIG_REGULATOR. This patch moves regulator platform
data handling from TPS65217 MFD driver to regulator driver.

This makes MFD driver independent of REGULATOR framework so
build error is fixed if CONFIG_REGULATOR is not set.

drivers/built-in.o: In function `tps65217_probe':
tps65217.c:(.devinit.text+0x13e37): undefined reference
to `of_regulator_match'

This patch also fix allocation size of tps65217 platform data.
Current implementation allocates a struct tps65217_board for each
regulator specified in the device tree. But the structure itself
provides array of regulators so one instance of it is sufficient.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
2012-08-22 10:49:35 +02:00
Tejun Heo 43829731dd workqueue: deprecate flush[_delayed]_work_sync()
flush[_delayed]_work_sync() are now spurious.  Mark them deprecated
and convert all users to flush[_delayed]_work().

If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.

This patch doesn't make any functional difference.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
2012-08-20 14:51:24 -07:00
Randy Dunlap 296c656616 regulator: fix kernel-doc warnings in drivers/regulator/core.c
Fix regulator kernel-doc warnings:

Warning(drivers/regulator/core.c:2308): No description found for parameter 'rdev'
Warning(drivers/regulator/core.c:2308): Excess function parameter 'regulator' description in 'regulator_set_voltage_time_sel'

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc:	Liam Girdwood <lrg@ti.com>
Cc:	Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-20 21:00:22 +01:00
Aaro Koskinen 908d6d5292 regulator: twl-regulator: fix up VINTANA1/VINTANA2
It seems commit 2098e95ce9 (regulator: twl:
adapt twl-regulator driver to dt) accidentally deleted VINTANA1. Also
the same commit defines VINTANA2 twice with TWL4030_ADJUSTABLE_LDO and
TWL4030_FIXED_LDO. This patch changes the fixed one to be VINTANA1.

I noticed this when auditing my N900 boot logs. I could not notice any
change in device behaviour, though, except that the boot logs are now
like before:

	...
	[    0.282928] VDAC: 1800 mV normal standby
	[    0.284027] VCSI: 1800 mV normal standby
	[    0.285400] VINTANA1: 1500 mV normal standby
	[    0.286865] VINTANA2: 2750 mV normal standby
	[    0.288208] VINTDIG: 1500 mV normal standby
	[    0.289978] VSDI_CSI: 1800 mV normal standby
	...

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
2012-08-15 17:19:01 +01:00
Marek Szyprowski b2a1ef473b regulator: core: request only valid gpio pins for regulator enable
Commit 65f735082d ("regulator: core: Add core support for GPIO controlled
enable lines") introduced enable gpio entry in regulator configuration
structure. Some drivers use '-1' as a placeholder for marking that such
gpio line is not available, because '0' is considered as a valid gpio
number. This patch fixes initialization of such drivers (like MAX8952
on UniversalC210 board), when '-1' is provided as enable gpio pin in the
regulator's platform data.

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-09 19:52:21 +01:00
Mark Brown f7df20ec32 regulator: core: Use list_voltage() to read single voltage regulators
If the regulator doesn't supply a way of reading back the voltage but does
provide a list_voltage() operation then use that with a selector of zero
to read the voltage.  Regulators doing this means that we have the list
operation there for consumers that want to configure themselves.

Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-09 19:48:27 +01:00
Mark Brown e76ab829cc regulator: twl: Remove references to the twl4030 regulator
It's not referenced anywhere any more and the compiler notices.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-09 12:13:56 +01:00
Uwe Kleine-König 215b8b055d regulator: make the dummy regulator's print_constraint more helpful
This prevents the output of just

	dummy:

in the boot log. Now it says:

	regulator-dummy: no parameters

which at least doesn't make it look like an accidental printk and also doesn't
only use "dummy" which could mean anything.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-08 14:31:53 +01:00
Heiko Stübner eb0c5686b3 regulator: gpio-regulator: Split setting of voltages and currents
Originally gpio-regulator used the first item of its state list
that matched the given voltage or current range.

Commit 4dbd8f63f0 (regulator: gpio-regulator: Set the smallest voltage/current
in the specified range) changed this, to make the selection independent of
the ordering of the state list.

But selecting the minimal value is only true for voltage regulators.
For current regulators the maximum in the given range should be
selected instead.

Therefore split the previous common selection function into specific
functions for voltage and current regulators.

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-08 12:16:06 +01:00
Linus Walleij cfa9cfbc08 regulator: ab3100: add missing voltage table
The conversion to voltage tables in

commit a3beb74261
"regulator: ab3100: Use regulator_list_voltage_table()"

missed to add the voltage table to the buck. Fix this and
it works like a charm.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:37 +01:00
Axel Lin 3e2a928472 regulator: anatop: Fix wrong mask used in anatop_get_voltage_sel
The mask used in anatop_get_voltage_sel does not match the mask used in
anatop_set_voltage_sel.
We need to do left shift anatop_reg->vol_bit_shift bits for the correct mask.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:26 +01:00
Laxman Dewangan 7f852e0584 regulator: tps6586x: correct vin pin for sm0/sm1/sm2
As per datasheet, the vin pin for the regulator is named
as vin_sm0, vin_sm1, vin_sm2 for sm0, sm1 and sm2 respectively.

Correcting the names in driver and documentation to match with
datasheet.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:26 +01:00
Axel Lin 1c9d2d71a3 regulator: palmas: Fix palmas_probe error handling
Fix below error handling cases:

1. If reading PALMAS_SMPS_CTRL fails, simply returns ret rather than goto
   err_unregister_regulator because we have not call regulator_register().
2. If palmas_ldo_init() fails, we need to call regulator_unregister() for the
   regulator we just successfully registered in this for loop iteration.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:26 +01:00
Axel Lin 2735daeb16 regulator: palmas: Call palmas_ldo_[read|write] in palmas_ldo_init
Current code uses wrong calls palmas_smps_[read|write] in palmas_ldo_init(),
should be palmas_ldo_[read|write] instead.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:26 +01:00
Axel Lin 12565b166d regulator: palmas: Fix regmap offsets for PALMAS_REG_SMPS10 vsel_reg
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:25 +01:00
Axel Lin a5f8ae2154 regulator: palmas: Fix calculating selector in palmas_map_voltage_ldo
This patch fixes below issues when choosing selector:

1. Current code returns negative selector if min_uV < 900000 which is wrong.
   For example, it is possible to satisfy the request with selector = 1 if
   the requested min_uV is 850000.
2. Current code may select a voltage lower than requested min_uV.
   For example, if the requested min_uV is 945000, current code chooses
   selector = 1 which is lower than requested min_uV.
   DIV_ROUND_UP to avoid this case.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:10:25 +01:00
Axel Lin 2f6c797f84 regulator: core: Fix cast to pointer from integer of different size warning
This is to address the following warning during compilation time: (Compile on x86_64)

  CC      drivers/regulator/core.o
drivers/regulator/core.c: In function '_regulator_do_set_voltage':
drivers/regulator/core.c:2183:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]

This patch adds a temporary variable to avoid double cast.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-07 18:07:55 +01:00
Michael Jones c6d678b632 regulator: Fix space/tab confusion
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-04 12:19:46 +01:00
Laxman Dewangan 57ad526ae2 regulator: core: increment open_count when regulator supply is set
When registering the regulator and setting supply for the regulator
then increment open_count to reflect correct number of users.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-04 11:58:39 +01:00
Mark Brown 4f842f6ba6 regulator: core: Clarify grammar for dummy help text
Too many thens in the if...then clause.

Reported-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-08-03 23:24:24 +01:00
Samuel Ortiz 938e05bf13 regulator: Fix an s5m8767 build failure
Due to a merge conflict we are getting this:

drivers/regulator/s5m8767.c: In function ‘s5m8767_pmic_probe’:
drivers/regulator/s5m8767.c:575:2: error: implicit declaration of function
‘s5m_reg_write’ [-Werror=implicit-function-declaration]

This is fixed by fully converting this driver to the new s5m API.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-31 00:51:09 +02:00
Linus Torvalds 3e701cdfe6 MFD bits for the 3.6 merge window.
We have support for a few new drivers:
 - Samsung s2mps11
 - Wolfson Microelectronics wm5102 and wm5110
 - Marvell 88PM800 and 88PM805
 - TI twl6041
 
 We also have our regular driver improvements:
 - Device tree and IRQ domain support for STE AB8500
 - Regmap and devm_* API conversion for TI tps6586x
 - Device tree support for Samsung max77686
 - devm_* API conversion for STE AB3100
 
 Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
 tps65090, da9052 and twl-core.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.12 (GNU/Linux)
 
 iQIcBAABAgAGBQJQFpGVAAoJEIqAPN1PVmxKFNoP/1dkYngrxxV6cxdyLJ74APhG
 lVKPgaDxQhdgfwCZJmMeZK1UphZo80cWnEXG6sTHZUEQdTaslSJu5SuPfUM+fo7e
 52/dU0nx0ZE04pwPQLHbidS4TmHlbLg9oM2kmIf9RO5rg34GodwVgRL/4+k1qvhz
 aWYJt9erFhQOpqaSX66mXHSuhvzHypbcE7d2B2Ykmh3NoYiH2w9H9KmIbbb+ZLq8
 +Bp/i5Ys/vfooo+8IE2w6KZfIzMwsmmtWjjr/38yuQJaKZCh/zn23DM9HsdrVf++
 RzfniRF4YBxmeKi7zi8MFIYys8filTCXA9dXbGSAKCuUCT37yZRnUxTeN1bn7Bux
 A7KRpG7pUKQKVKqCTndvK5LcQKlT33XyW2ZzV1wVWX2JkCJ+gilPeykb8IabNvGX
 nIp0STEGR/WdCLEAKo8pJF7Usn0RuUzAug02SG/mQ6dpnLoZqp0Od5W7gRhT7M7h
 hXr/xKJ6cG5YwicpAdy5kJJ0dRgQrtaHwxrF0B68AXZ7CmAtkPuEGCYhUCFnGQUH
 XJ0CodAqqVBRyYiQS4zIpIh2nqhIdsgv4OC1+kVLbubQk+PR88zG9Jvg6i1HQi/A
 OHi7N5Wite3YUrs3sBzDKnEc/Il2YRhVaz2SLVNfZR0PS7hywHN3rK/tVFINTgei
 jNEz1H6hu7ToNLfs0UzP
 =c28c
 -----END PGP SIGNATURE-----

Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6

Pull MFD bits from Samuel Ortiz:
 "We have support for a few new drivers:
   - Samsung s2mps11
   - Wolfson Microelectronics wm5102 and wm5110
   - Marvell 88PM800 and 88PM805
   - TI twl6041

  We also have our regular driver improvements:
   - Device tree and IRQ domain support for STE AB8500
   - Regmap and devm_* API conversion for TI tps6586x
   - Device tree support for Samsung max77686
   - devm_* API conversion for STE AB3100

  Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
  tps65090, da9052 and twl-core."

Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac9651: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").

In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).

I left that part of commit 2761a63945 just undone.

* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
  mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
  mfd: Arizone core should select MFD_CORE
  mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
  mfd: Add debug trace on entering and leaving arizone runtime suspend
  mfd: Correct tps65090 cell names
  mfd: Remove gpio support from tps6586x core driver
  ARM: tegra: defconfig: Enable tps6586x gpio
  gpio: tps6586x: Add gpio support through platform driver
  mfd: Cache tps6586x register through regmap
  mfd: Use regmap for tps6586x register access.
  mfd: Use devm managed resources for tps6586x
  input: Add onkey support for 88PM80X PMIC
  mfd: Add support for twl6041
  mfd: Fix twl6040 revision information
  mfd: Matches should be NULL when populate anatop child devices
  input: ab8500-ponkey: Create AB8500 domain IRQ mapping
  mfd: Add missing out of memory check for pcf50633
  Documentation: Describe the AB8500 Device Tree bindings
  mfd: Add tps65910 32-kHz-crystal-input init
  mfd: Drop modifying mc13xxx driver's id_table in probe
  ...
2012-07-30 12:41:17 -07:00
Linus Torvalds bdc0077af5 SCSI misc on 20120724
The most important feature of this patch set is the new async infrastructure
 that makes sure async_synchronize_full() synchronizes all domains and allows
 us to remove all the hacks (like having scsi_complete_async_scans() in the
 device base code) and means that the async infrastructure will "just work" in
 future. The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
 megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure work in
 sas and FC.
 
 Signed-off-by: James Bottomley <JBottomley@Parallels.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJQDjDCAAoJEDeqqVYsXL0M/sMH/jVgBfF1mjR+DQuTscKyD21w
 0BQLn5OmvDZDqo44iqQzNRObw7CxkBkUtHoozsknLijw+KggER653ZOAtUdIHfI/
 /uo7iJQ3J3D/Ezm99HYSpZiF2juZwsBRtFBoKkGqOpMlzFUx5o4hUbH5OcINxnHR
 VmvJU5K1kg8D77Q6zK+Atl14/Rfibc2IoufFmbYdplUAM/tV0BpBSSHJAJvqua76
 NGMl4KJcPZnXe/4LXcxZia5A2efdFFEzaQ2mM9rUVEAgHDAxc0Zg9IoDhGd08FX4
 G55NK+6+bKb9s7bgyva0T/iy817TRCzjteeYNFrb8nBRe7aQbAivaBHQFXIyvdQ=
 =y2sh
 -----END PGP SIGNATURE-----

Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull first round of SCSI updates from James Bottomley:
 "The most important feature of this patch set is the new async
  infrastructure that makes sure async_synchronize_full() synchronizes
  all domains and allows us to remove all the hacks (like having
  scsi_complete_async_scans() in the device base code) and means that
  the async infrastructure will "just work" in future.

  The rest is assorted driver updates (aacraid, bnx2fc, virto-scsi,
  megaraid, bfa, lpfc, qla2xxx, qla4xxx) plus a lot of infrastructure
  work in sas and FC.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (97 commits)
  [SCSI] Revert "[SCSI] fix async probe regression"
  [SCSI] cleanup usages of scsi_complete_async_scans
  [SCSI] queue async scan work to an async_schedule domain
  [SCSI] async: make async_synchronize_full() flush all work regardless of domain
  [SCSI] async: introduce 'async_domain' type
  [SCSI] bfa: Fix to set correct return error codes and misc cleanup.
  [SCSI] aacraid: Series 7 Async. (performance) mode support
  [SCSI] aha152x: Allow use on 64bit systems
  [SCSI] virtio-scsi: Add vdrv->scan for post VIRTIO_CONFIG_S_DRIVER_OK LUN scanning
  [SCSI] bfa: squelch lockdep complaint with a spin_lock_init
  [SCSI] qla2xxx: remove unnecessary reads of PCI_CAP_ID_EXP
  [SCSI] qla4xxx: remove unnecessary read of PCI_CAP_ID_EXP
  [SCSI] ufs: fix incorrect return value about SUCCESS and FAILED
  [SCSI] ufs: reverse the ufshcd_is_device_present logic
  [SCSI] ufs: use module_pci_driver
  [SCSI] usb-storage: update usb devices for write cache quirk in quirk list.
  [SCSI] usb-storage: add support for write cache quirk
  [SCSI] set to WCE if usb cache quirk is present.
  [SCSI] virtio-scsi: hotplug support for virtio-scsi
  [SCSI] virtio-scsi: split scatterlist per target
  ...
2012-07-24 18:11:22 -07:00
Mark Brown 3384fb9884 Merge branch 'regulator-drivers' into regulator-next 2012-07-22 19:32:00 +01:00
Mark Brown 8cfc545e0e Merge branches 'regulator-core', 'regulator-dt' and 'regulator-dummy' into regulator-next 2012-07-22 19:31:41 +01:00
Kim, Milo ade7515fef regulator: add new lp8788 regulator driver
TI LP8788 PMU has 4 BUCKS and 22 LDOs.
The voltage of BUCK1 and BUCK2 can be controlled by external gpios.
And some LDOs also can be enabled by external gpios.
The regmap interface is used for regulator operations.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-20 11:12:15 +01:00
Axel Lin c798881e88 regulator: mc13xxx: Remove extern function declaration for mc13xxx_sw_regulator
This function does not exist, remove the extern function declaration.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-20 11:12:14 +01:00
Dan Williams 2955b47d2c [SCSI] async: introduce 'async_domain' type
This is in preparation for teaching async_synchronize_full() to sync all
pending async work, and not just on the async_running domain.  This
conversion is functionally equivalent, just embedding the existing list
in a new async_domain type.

The .registered attribute is used in a later patch to distinguish
between domains that want to be flushed by async_synchronize_full()
versus those that only expect async_synchronize_{full|cookie}_domain to
be used for flushing.

[jejb: add async.h to scsi_priv.h for struct async_domain]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
2012-07-20 09:05:54 +01:00
Laxman Dewangan d2cfdb055d regulator: tps65910: set input_supply on desc unconditionally
Set the supply_name in the regulator descriptor unconditionally
and make this parameter as required parameter in the device
node for successfully registration of the regulator.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-17 11:08:46 +01:00
Axel Lin 8a165df7a9 regulator: palmas: Fix calcuating selector in palmas_map_voltage_smps
The logic of calculating selector in palmas_map_voltage_smps() does not match
the logic to list voltage in palmas_list_voltage_smps().

We use below equation to calculate voltage when selector > 0:
        voltage = (0.49V + (selector * 0.01V)) * RANGE
RANGE is either x1 or x2

So we need to take into account with the multiplier set in VSEL register when
calculating selector in palmas_map_voltage_smps()

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-17 11:07:26 +01:00
Axel Lin 5bae062830 regulator: lp872x: Simplify implementation of lp872x_find_regulator_init_data()
Pass regulator id rahter than the index to lp872x_find_regulator_init_data(),
then the code can be simpler.
We can also get max_regulators by lp->num_regulators.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Tested-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-16 20:58:30 +01:00
Axel Lin c6a717c9d7 regulator: twl: Fix list_voltate for twl6030ldo_ops
According to the datasheet, the voltage for twl6030ldo_ops is not linear for
all cases. Linear mapping is only for the selection code from
00000001 to 00011000.

Table 9. LDO Output Voltage Selection Code
CODE     VOUT(V)    COD      VOUT(V)    CODE     VOUT(V)    CODE     VOUT(V)
00000000 0          00001000 1.7        00010000 2.5        00011000 3.3
00000001 1.0        00001001 1.8        00010001 2.6        00011001 Reserved
00000010 1.1        00001010 1.9        00010010 2.7        00011010 Reserved
00000011 1.2        00001011 2.0        00010011 2.8        00011011 Reserved
00000100 1.3        00001100 2.1        00010100 2.9        00011100 Reserved
00000101 1.4        00001101 2.2        00010101 3.0        00011101 Reserved
00000110 1.5        00001110 2.3        00010110 3.1        00011110 Reserved
00000111 1.6        00001111 2.4        00010111 3.2        00011111 2.75

This patch implements the list_voltage callback based on above table.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-16 20:58:02 +01:00
Sangbeom Kim 54227bcf20 mfd: Modify samsung mfd header
As Prefix of Samsung pmic changed from s5m to s2m,
To make common mfd driver for s2m and s5m series,
This patch rename header of Samsung mfd and modify mfd driver.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-16 14:28:11 +02:00
Sangbeom Kim 63063bfbff mfd: Modify samsung mfd driver for common api
Previous naming rule of samsung pmic start with s5m prefix.
But It is changed by s2m.
To cover various samsung s2m and s5m series,
This patch modify function and variable name for common usage.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-16 14:26:45 +02:00
Sangbeom Kim 66c9fbb989 mfd: Rename s5m file and directories to samsung
Previously, Samsung PMIC naming rule start with prefix of s5m.
But Naming rule is changed.
From now on, Prefix will be changed to s2m.
So, To support pmic series of s5m and s2m, change mfd file and directory name.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-16 12:57:35 +02:00
Axel Lin 4bcb9f4342 regulator: twl: Convert twl6030ldo_ops to [get|set]_voltage_sel
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-15 22:06:05 +01:00
Axel Lin a3cb80f43a regulator: twl: Fix the formula to calculate vsel and voltage for twl6030ldo
In twl6030ldo_set_voltage, current code use below formula to calculate vsel:
        vsel = (min_uV/1000 - 1000)/100 + 1;
This is worng because when min_uV is 1000000 uV, vsel is 1.
It should be 0 in this case.
Fix it by change the equation to: (This equation is common for linear mapping)
        vsel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step);

In twl6030ldo_get_voltage, current code use below formula to calculate voltage:
        mV = 1000mv + 100mv * (vsel - 1)
This is worng because when vsel is 0, mV is 900mV. Note the min_uV is 1000mV.
Fix it by change the equation to: (This equation is common for linear mapping)
        return rdev->desc->min_uV + vsel * rdev->desc->uV_step;

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-15 22:06:05 +01:00
Axel Lin 5febb3c9d5 regulator: s5m8767: Properly handle gpio_request failure
Convert to devm_gpio_request to save a few error handling code.

This patch properly handle the gpio_request failure, we should return error
when gpio_request fails rather than just show warning.

I think one of the reason we got -EBUSY is because current code does not free
gpios in s5m8767_pmic_remove(). So it got -EBUSY when reload the module.

Yest another reason is in current code if gpio_request() returns error,
the rest of the code still calls gpio_direction_output to config buck_gpios
and buck_ds gpios. This looks wrong to me.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-15 21:49:53 +01:00
Axel Lin 8fa25eda86 regulator: max8997: Properly handle gpio_request failure
Convert to devm_gpio_request to save a few error handling code.

This patch properly handle the gpio_request failure with -EBUSY, we should
return error rather than ommit the gpio_request failure with -EBUSY.

I think one of the reason we got -EBUSY is because current code does not free
gpios in max8997_pmic_remove(). So it got -EBUSY when reload the module.

Yest another reason is in current code if gpio_request() returns -EBUSY,
the rest of the code still calls gpio_direction_output to config buck125_gpios
and set gpio value in max8997_set_gpio().  This looks wrong to me.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-15 21:49:53 +01:00
Laxman Dewangan 8a8e3d5915 regulator: tps62360: use devm_* for gpio request
Use devm_ version of gpio APIs gpio_request_one() for
requesting gpios.
This avoid extra code for freeing gpios.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-15 21:49:52 +01:00
Mark Brown d5b2e30bdc Linux 3.5-rc7
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJQAfWKAAoJEHm+PkMAQRiG/DwIAIullMhkDhD/GJcn24ZbUJoa
 v6zRPK2hIavuKH/6bUoUiXT346PUYgVnRMhetuYKJFURz6KX/nmlxve/iXNn/WP1
 9hnxhE+zcnp2qKI83c3Yok09eed1KnGY5hWQkqXM2gzji/OU0pCKchOcL01l//uz
 iiWpNAXEVUnT92CafnHlZ55f/MWVqRFmDKi3Ty1YKSskhojQ6NOPsWCxrTxKVbim
 2YPXc3D+xLHzF12ufVgla20AF4KnK8m+tFugniRAqArIagpzBUP1x1wk0RN5PyBD
 FTP8lv7bSfBusp41/mPDB66WAe9EfQBoWQY6jloJjp0i8xnMyH5V05pImBV5NwU=
 =O+gl
 -----END PGP SIGNATURE-----

Merge tag 'v3.5-rc7' into regulator-drivers

Linux 3.5-rc7
2012-07-15 21:49:21 +01:00
Laxman Dewangan 7c7fac3058 regulator: tps6586x: add support for input supply
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-13 15:21:18 +01:00
AnilKumar Ch a7f1b63eb8 regulator: tps65217: Add device tree support
This commit adds device tree support for tps65217 pmic. And usage
details are added to device tree documentation. Driver is tested
by using kernel module with regulator set and get APIs.

Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:27:36 +01:00
Axel Lin 257ee3c6dd regulator: aat2870: Remove unused min_uV and max_uV from struct aat2870_regulator
Both min_uV and max_uV are not used in the code, remove them.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:22:13 +01:00
Axel Lin 4506c6d5ea regulator: aat2870: Convert to regulator_list_voltage_table
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:22:13 +01:00
Axel Lin e76b9cc7b8 regulator: da9052: initialize of_node param for regulator register
Initialize config.of_node for regulator before registering.
This is needed for DT based regulator support.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:21:24 +01:00
Krystian Garbaciak 1beaf762b4 regulator: Add REGULATOR_STATUS_UNDEFINED.
REGULATOR_STATUS_UNDEFINED is to be returned by regulator, if any other state
doesn't really apply.

Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:19:24 +01:00
Krystian Garbaciak 03ffcf3d08 regulator: Fix a typo in regulator_mode_to_status() core function.
Case REGULATOR_STATUS_STANDBY -> REGULATOR_MODE_STANDBY.

Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:19:20 +01:00
Axel Lin c06eed397a regulator: s2mps11: Use sec_reg_write rather than sec_reg_update when mask is 0xff
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:07:11 +01:00
Axel Lin 232b250475 regulator: s2mps11: Fix wrong setting for config.dev
Currently s2mps11->iodev, s2mps11->dev and config.dev point to NULL.
This patch fixes the settings for config.dev.
Current code does not need the *dev and *iodev of struct s2mps11_info,
so remove them.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:06:48 +01:00
Axel Lin 2693fcab1a regulator: s2mps11: Fixup missing commas
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:06:35 +01:00
Axel Lin faa95fde43 regulator: tps65910: Remvoe tps65910_reg_[read|modify_bits|read_locked|write_locked] functions
The tps65910 mfd driver has been converted to regmap APIs.
This patch adds tps65910_reg_update_bits() in include/linux/mfd/tps65910.h.
Thus we can use tps65910_reg_read/tps65910_reg_write/tps65910_reg_update_bits
directly and remove tps65910_reg_[read|modify_bits|read_locked|write_locked]
functions. With this change, we can also remove the mutex in struct tps65910_reg.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Tested-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-12 18:05:15 +01:00
Sangbeom Kim cb74685ecb regulator: s2mps11: Add samsung s2mps11 regulator driver
This patch add Samsung S2MPS11 regulator driver.
The S2MPS11 can support 10 Bucks and 38 LDOs and RTC.
Especially, S2MPS11 is designed for high performance
Samsung application processor.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-11 15:32:40 +01:00
Laxman Dewangan 7be531883a regulator: tps65910: correct init value of n_voltages
Recent change in the core driver to get the maximum voltage
is based on the (n_voltages -1) steps of voltage.
For the tps65910, the (n_voltages -1)th step voltage is
calculated based on the callback function list_voltage.
This function direct maps the datasheet and adjust the
first few steps for initial voltage as per datasheet,
and hence initialize the n_voltages based on datasheet.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-10 17:16:05 +01:00
Axel Lin b669e0adb9 regulator: max8952: Use core GPIO enable support
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-10 14:48:42 +01:00
Axel Lin aa851193bd regulator: max8998: Remove wrong set_suspend_[en|dis]able callback settings
Using the same ops for both [en|dis]able and set_suspend_[en|dis]able
callbacks is actively broken. This patch removes .set_suspend_disable and
.set_suspend_enable callback setting.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-09 19:45:12 +01:00
Axel Lin b1a397dc1a regulator: max8952: Remove wrong set_suspend_disable callback setting
Using the same ops for both .disable and .set_suspend_disable callbacks is
actively broken. This patch removes .set_suspend_disable callback setting.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-09 19:45:11 +01:00
Axel Lin b86bbddd6f regulator: da9052: Use for_each_child_of_node() macro
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-09 19:38:58 +01:00
Lee Jones bad76991d7 mfd: Register ab8500 devices using the newly DT:ed MFD API
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 00:16:13 +02:00
Lee Jones 5d90322bc8 mfd: Register db8500-prcmu devices using the newly DT:ed MFD API
Now the MFD API is Device Tree aware we can use it for platform
registration again, even when booting with DT enabled. To aid in
Device Node pointer allocation we provide each cell with the
associative compatible string.

Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-09 00:16:09 +02:00
Yadwinder Singh Brar d1ef065d43 regulator: max77686: Initialise rmatch.of_node to NULL.
Now of_regulator_match() returns without finding the match if match->of_node
is not NULL.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-06 19:17:29 +01:00
Laxman Dewangan 19228a6a59 regulator: tps65910: add support for input supply
There is multiple voltage input pins on device which
takes the voltage input for different voltage regulator.
Support to configure the voltage input supplied by
different regulator for each regulators.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-06 19:11:05 +01:00
Mark Brown 86f5fcfc3e regulator: core: Mark all DT based boards as having full constraints
Since DT doesn't provide an idiomatic mechanism for enabling full
constraints and since it's much more natural with DT to provide them
just assume that a DT enabled system has full constraints.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2012-07-06 18:57:33 +01:00
Laxman Dewangan 6be5bfc3bf regulator: fixed: dt: support for input supply
Add support for input supply in DT parsing of node.
The input supply will be provided by the property
"vin-supply" in the regulator node.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-05 13:49:35 +01:00
Yadwinder Singh Brar 4706fcab9b regulator: max77686: Add device tree support.
This patch device tree support for regulator driver. It uses the parent
(mfd's) DT node to parse the regulator data for max77686.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-05 13:42:06 +01:00
Axel Lin 6c3b956b94 regulator: ab3100: Use rdev_get_drvdata() rather than use reg->reg_data driectly
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-05 13:34:39 +01:00
Axel Lin f8568cbd94 regulator: ab3100: Set enable enable_time in regulator_desc
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-05 13:34:00 +01:00
Shawn Guo e2c98eaf92 regulator: core: remove sysfs entry properly in regulator_put
With changes introduced by commit 222cc7b (regulator: core: Allow
multiple requests of a single supply mapping) on create_regulator,
regulator_put needs a corresponding update on sysfs entry removing.

Also regulator->dev still needs to get assigned in create_regulator,
otherwise, sysfs_remove_link call in regulator_put will get bypassed.

Reported-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-05 13:15:40 +01:00
Mark Brown 6dc027c977 regulator: arizona-micsupp: Force regulated mode until we have API support
It's almost certainly what the user would expect.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-04 16:22:39 +01:00
Axel Lin 9c6a74c5e0 regulator: ad5398: Fix min/max current limit boundary checking
It is ok to request current limit with min_uA < chip->min_uA and
max_uA > chip->max_uA.

We need to set min_uA = chip->min_uA if (min_uA < chip->min_uA),
this ensures the equation to calcuate selator does not return negative number.

Also set max_uA = chip->max_uA if (max_uA > chip->max_uA), as suggested by
Sonic.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-04 12:39:38 +01:00
Axel Lin fca53d862d regulator: twl: Set enable enable_time in regulator_desc
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-04 12:38:37 +01:00
Axel Lin 4b7c948f55 regulator: gpio-regulator: Use core GPIO enable support
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-04 12:38:36 +01:00
Axel Lin a2a8222be8 regulator: gpio-regulator: Set enable enable_time in regulator_desc
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-04 12:38:35 +01:00
Axel Lin 94f48ab32b regulator: tps65910: Set enable enable_time in regulator_desc
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-04 12:37:54 +01:00
Mark Brown a9905b1d6f regulator: arizona-ldo1: Implement GPIO enable support
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:30 +01:00
Mark Brown 495fd8c8fd regulator: wm8994: Use core GPIO enable support
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:29 +01:00
Mark Brown 25a53dfbfb regulator: fixed: Use core GPIO enable support
This is essentially the code that was factored out into the core when the
feature was implemented.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:28 +01:00
Mark Brown 65f735082d regulator: core: Add core support for GPIO controlled enable lines
It is very common for regulators to support having their enable signal
controlled by a GPIO. Since there are a bunch of fiddly things to get
right like handling the operations when the enable signal is tied to
a rail and it's just replicated code add support for this to the core.

Drivers should set ena_gpio in their config if they have a GPIO control,
using ena_gpio_flags to specify any flags (including GPIOF_OUT_INIT_ for
the initial state) and ena_gpio_invert if the GPIO is active low. The
core will then override any enable and disable operations the driver has
and instead control the specified GPIO.

This will in the future also allow us to further extend the core by
identifying when several enable signals have been tied together and
handling this properly.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:27 +01:00
Mark Brown 5c5659d0a2 regulator: core: Factor out enable and disable operations some more
Create new _regulator_do_enable() and _regulator_do_disable() operations
which deal with the mechanics of performing the enable and disable, partly
to cut down on the levels of indentation and partly to support some future
work.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:26 +01:00
Mark Brown eefaa3c628 regulator: wm831x-ldo: Specify enable time for alive LDO
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:25 +01:00
Mark Brown 00581b30ae regulator: wm8994: Set enable_time in descriptor
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:29:24 +01:00
Mark Brown 3d0f267fcd regulator: fixed: Set enable enable_time in regulator_desc
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:28:41 +01:00
Mark Brown 79511ed322 regulator: core: Allow fixed enable_time to be set in the regulator_desc
Many regulators have a fixed specification for their enable time. Allow
this to be set in the regulator_desc as a number to save them having to
implement an explicit operation.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:28:33 +01:00
Mark Brown e113d792d5 regulator: core: Check that the selector from map_voltage() is valid
Lots of regulator drivers have checks in their map_voltage() functions
to verify that the result of the mapping is in the range originally
specified. Factor these out in the core and provide a bit of extra
defensiveness for other drivers by doing the check in the core.

Since we're now doing a list_voltage() earlier move the current mapping
back to a voltage out into the set_voltage() call to save redoing it.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:28:04 +01:00
Mark Brown c5f3939b8f regulator: core: Support fixed voltages in regulator_is_supported_voltage()
Currently regulator_is_supported_voltage() works by enumerating the set
of voltages which can be set by the regulator but the checks we're doing
to impose constraints mean that if we can't vary the voltage we'll not
report any voltages as supported even though the regulator is actually
set at that voltage.

We could fix the voltage listing but this would mean that list_voltage()
could end up going to the hardware to get the current voltage which isn't
expected (it's supposed to be very cheap) so instead special case things
when we can't change the voltage and compare the requested range against
the current voltage.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:27:58 +01:00
Stephen Boyd d92d95b6bf regulator: Fix recursive mutex lockdep warning
A recursive lockdep warning occurs if you call
regulator_set_optimum_mode() on a regulator with a supply because
there is no nesting annotation for the rdev->mutex. To avoid this
warning, get the supply's load before locking the regulator's
mutex to avoid grabbing the same class of lock twice.

=============================================
[ INFO: possible recursive locking detected ]
3.4.0 #3257 Tainted: G        W
---------------------------------------------
swapper/0/1 is trying to acquire lock:
 (&rdev->mutex){+.+.+.}, at: [<c036e9e0>] regulator_get_voltage+0x18/0x38

but task is already holding lock:
 (&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&rdev->mutex);
  lock(&rdev->mutex);

 *** DEADLOCK ***

 May be due to missing lock nesting notation

3 locks held by swapper/0/1:
 #0:  (&__lockdep_no_validate__){......}, at: [<c03dbb48>] __driver_attach+0x40/0x8c
 #1:  (&__lockdep_no_validate__){......}, at: [<c03dbb58>] __driver_attach+0x50/0x8c
 #2:  (&rdev->mutex){+.+.+.}, at: [<c036ef38>] regulator_set_optimum_mode+0x24/0x224

stack backtrace:
[<c001521c>] (unwind_backtrace+0x0/0x12c) from [<c00cc4d4>] (validate_chain+0x760/0x1080)
[<c00cc4d4>] (validate_chain+0x760/0x1080) from [<c00cd744>] (__lock_acquire+0x950/0xa10)
[<c00cd744>] (__lock_acquire+0x950/0xa10) from [<c00cd990>] (lock_acquire+0x18c/0x1e8)
[<c00cd990>] (lock_acquire+0x18c/0x1e8) from [<c080c248>] (mutex_lock_nested+0x68/0x3c4)
[<c080c248>] (mutex_lock_nested+0x68/0x3c4) from [<c036e9e0>] (regulator_get_voltage+0x18/0x38)
[<c036e9e0>] (regulator_get_voltage+0x18/0x38) from [<c036efb8>] (regulator_set_optimum_mode+0xa4/0x224)
...

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:25:58 +01:00
Laxman Dewangan 5260cd2bc9 regulator: dt: regulator match by regulator-compatible
Match the device's regulators with the property of
"regulator-compatible" of each regulator node.

Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:19:41 +01:00
Axel Lin 844e6901df regulator: tps65217: Fix voltage boundary checking in tps65217_pmic_map_voltage
It is ok to request voltage with min_uV < tps->info[rid]->min_uV and
max_uV > tps->info[rid]->max_uV.

The equation we used in uv_to_vsel() does not allow
min_uV < tps->info[rid]->min_uV, otherwise it returns negative selector.
So we need to set min_uV = tps->info[rid]->min_uV if
min_uV < tps->info[rid]->min_uV.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-03 20:18:34 +01:00
Axel Lin 0072f0a82c regulator: tps62360: Convert to regulator_set_voltage_time_sel()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-02 18:27:10 +01:00
Alan Cox 1a5d39d064 regulator: tps65217: invalid if check
This permits the setting of bogus values because the invalidity check is
itself invalid.

Reported-by: dcb314@hotmail.com
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-02 18:26:04 +01:00
Axel Lin 1e12dfc968 regulator: tps6524x: Convert fixed ilimsel to table based
This patch refactors the code to get rid of the fixed_ilimsel and FIXED_ILIMSEL
flag usage, and convert all the fixed ilimsel to table based (with one entry in
the table).

We can differentiate fixed ilimsel by checking info->n_ilimsels == 1,
thus FIXED_ILIMSEL flag can be removed.

This change makes the logic of the code simpler as all the ilimsels are table
based now.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-02 18:26:03 +01:00
Axel Lin cac87fd34e regulator: tps6524x: Convert to regulator_list_voltage_table()
This patch adds fixed_5000000_voltage table for fixed voltage,
so we can convert regulator_ops to regulator_list_voltage_table.

We can differentiate fixed voltage by checking rdev->desc->n_voltages == 1,
thus remove the FIXED_VOLTAGE flag usage.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-02 18:26:02 +01:00
Mark Brown 744c62eb65 Linux 3.5-rc5
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJP74cgAAoJEHm+PkMAQRiG1mMH/A1uPaF6CZhyaDHRYAdlxzIl
 OQ5FJNlX1vzPZg6VLiNi4KxcbfgVrVSU6oghD6ASmoWje7PkhbzzoJVeUu9DYbbQ
 oz/IXJi/SqYMhbZvqZ4DsCY25sZNWsWfeabs38hil9BEaxj6xOqF1iR0RUrvcRoP
 K6kyYUNk2C7q8w/ouco5kmIcEWf6xD4bJWInyL5r/VGpRnNeZewFfsHoZ8tUWxwA
 ndsD45njKqnSHfBTipkVMXanHZQC0rpwLi+Rxv/+yBlQdDFVxD+RFrjLmV98XKLb
 dFZzV9WiuiMM1qnwiolQYMNUT8ZJYLzy04duG8wGqwzh5rWo3tv+01wAbAtTFvg=
 =4UfY
 -----END PGP SIGNATURE-----

Merge tag 'v3.5-rc5' into regulator-drivers

Linux 3.5-rc5 collides with further development.

Conflicts:
	drivers/regulator/tps65023-regulator.c
2012-07-02 18:24:59 +01:00
Stephen Warren f141822b15 regulator: fixed: support deferred probe for DT GPIOs
of_get_named_gpio() needs the driver hosting the GPIO that the DT
property references to have been probed. Detect this specific failure,
and defer the probe of the whole regulator until this API can complete.

Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-01 19:12:59 +01:00
Axel Lin d172f319c1 regulator: tps65217: Convert LDO1 to use regulator_list_voltage_table
Convert tps65217_pmic_ldo1_ops to use regulator_list_voltage_table.

We have n_voltages and volt_table settings in regulator_desc,
so we don't need the table and table_len fields in struct tps_info.
Thus remove them from struct tps_info.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-01 19:12:58 +01:00
Fabio Estevam bf2516cd02 regulator: core: Remove unused get_device_regulator
commit 222cc7b1 (regulator: core: Allow multiple requests of a single supply mapping)
removed the usage of get_device_regulator().

Remove the function definition too amd get rid of the following warning:

drivers/regulator/core.c:112:26: warning: 'get_device_regulator' defined but not used [-Wunused-function]

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-27 15:04:03 +01:00
Mark Brown 222cc7b1ce regulator: core: Allow multiple requests of a single supply mapping
Sometimes it may be useful to allow a device to request a supply multiple
times, for example in order to allow framework management of some uses of
the supply with some additional driver specific management or in order to
allow multiple children of an MFD to work with the supply. Currently this
is not possible due to the creation of

Solve this by removing the requested_uA entry (we have no current users
of this feature anyway) and ignoring errors creating the symlink to the
consumer. We should do something nicer than this as this causes sysfs to
spew enormous warnings but it allows users to run for now.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
2012-06-26 11:53:47 +01:00
Mark Brown 5aff3a8b20 regulator: core: Check for failed voltage sets before checking for delay
There is no need to consider waiting for the voltage to ramp if we
didn't manage to set it and looking at the return value is going to be
cheaper than is_enabled().

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-26 11:53:35 +01:00
Axel Lin e2eb169b1b regulator: s5m8767: Convert to regulator_list_voltage_linear
In current code, .list_voltage and .set_voltage_sel callbacks for BUCK7 and
BUCK8 return -EINVAL.

This patch adds s5m8767_buck78_ops for BUCK7 and BUCK8 which does not set
.list_voltage, .get_voltage_sel and .set_voltage_sel. ( This has the same
effect of returning -EINVAL in the callbacks)

Then for all the users of s5m8767_list_voltage, we don't need to worry about
the case reg_voltage_map[reg_id] is NULL.
So we can convert s5m8767_list_voltage to regulator_list_voltage_linear.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-26 11:50:33 +01:00
Axel Lin 7f217d36dc regulator: arizona-micsupp: Fix choosing selector in arizona_micsupp_map_voltage
If min_uV is in the range of: 3250001~3269999,
current code uses the equation:
        selector = DIV_ROUND_UP(min_uV - 1700000, 50000);
Then selector will be 32.
Then arizona_micsupp_list_voltage returns -EINVAL for this case which is wrong.

This patch fixes this issue:
If min_uV > 3200000, selector should be ARIZONA_MICSUPP_MAX_SELECTOR.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-26 11:48:05 +01:00
Mark Brown 1910efa1d0 regulator: Add driver for Arizona LDO1
Arizona class devices feature an integrated LDO which is intended to
supply the digital core for the device. Provide a driver offering
minimal control of this regulator.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-25 10:32:51 +01:00
Sangbeom Kim 1af142c6f9 regulator: Modify ramp_delay value for s5m8767a
As s5m8767a is revisioned, ramp_delay register is changed.
5mV/uS, 10mV/uS, 25mV/uS, 50mV/uS, 100mV/uS ramp delay can be selected.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-25 10:12:30 +01:00
Mark Brown 85e63343f4 Linux 3.5-rc4
-----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.18 (GNU/Linux)
 
 iQEcBAABAgAGBQJP53AxAAoJEHm+PkMAQRiGs2QH/RaqkXz96fwjhDcyiKpDqA3c
 kGuS5mz5cOhnqKSmR88HFm6pwuhLux/qSJzeAmoQy1MC8a0ACx7AnANW0lfN3/qe
 /HGYz8h60yCL/fhn8/bUYtdt9xsoDqoDcq/ooFl9mcsJGWbC6WeMSZU5dAUYqviE
 qFrp5zjY07FG53CRGT0hFpezQNwNL+VLH30CF9LD+fJLPVEYum2zBNGXWM42rcw5
 fxzGL/6SO8YqA/Upic1ht6HAd6s5LOrlST7qvnyXUMvRXN5z/Y92ueYJZefkS1Om
 ohuLIKM2bv9/dJS67H8N2baSKGCzBdfSe5/5WaHdLYW9MiVju0wRl6HPJtAMrkk=
 =H8t8
 -----END PGP SIGNATURE-----

Merge tag 'v3.5-rc4' into regulator-drivers

Linux 3.5-rc4 contains patches which conflict with some of the
development work.
2012-06-25 10:11:40 +01:00
Axel Lin 2f6ae6ef63 regulator: rc5t583: Use regulator_set_voltage_time_sel()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-24 12:13:38 +01:00
Axel Lin f11d08c3d6 regulator: Use list_voltage() to get voltage in regulator_set_voltage_time_sel
With this change, regulator_set_voltage_time_sel() can be more generic and not
limited to linear and table based mapping now.
One side-effect of this change is that list_voltage() must be implemented.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-23 12:28:12 +01:00
Axel Lin baae019efe regulator: max8998: Convert to set_voltage_sel and regulator_map_voltage_linear
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-23 12:18:08 +01:00
Axel Lin 9a0fbb627c regulator: max8998: Convert to regulator_list_voltage_linear()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-23 12:16:42 +01:00
Axel Lin b515241522 regulator: tps62360: Remove chip_id and voltage_base from struct tps62360_chip
The chip_id is not used.
The voltage_base is not necessary, set base voltage to tps->desc.min_uV instead.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-23 12:16:42 +01:00
Graeme Gregory a68de07461 regulator: palmas: fix regmap offsets for enable/disable
I forgot to apply the offsets for the regmap helper functions for
enable/disable on SMPS10 and the LDO regulators. This means regulators
will not enable/disable correctly.

Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-23 11:37:28 +01:00
Mark Brown b19dbf711e regulator: core: Add export of regulator_set_voltage_time_sel()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-23 11:34:20 +01:00
Axel Lin d9fe28f962 regulator: tps65910: Convert to regulator_list_voltage_table
Convert tps65910_ops and tps65910_ops_vdd3 to regulator_list_voltage_table.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-22 10:13:31 +01:00
Axel Lin f6442aa0b5 regulator: tps65910: Remove unused min_uV and max_uV from struct tps_info
The min_uV and max_uV fields of struct tps_info are not used in the code.
For the case voltage_table is provided, the min_uV and max_uV are the same
values as volt_table[0] and volt_table[n_voltages -1].
For the case voltage_table is not available, having the min_uV and max_uV seems
misleading. Current code uses equations to get the voltage value in this case,
but these equations do not use the min_uV and max_uV fields of struct tps_info.

Thus this patch removes the min_uV and max_uV fields from struct tps_info.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-22 10:13:22 +01:00
Kim, Milo b222a817b4 regulator: change message level on probing lp872x driver
Use err log rather than warning message when the platform data is NULL

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-21 11:04:06 +01:00
Mark Brown dc2060cfe2 regulator: lp872x: Depend on I2C=y
Kconfig doesn't do the right thing for us here.

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-21 10:38:37 +01:00
Axel Lin 01bc3a1400 regulator: tps65910: Convert to regulator_set_voltage_time_sel()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-21 10:35:10 +01:00
Mark Brown b667a45d9f regulator: arizona: Add support for microphone supplies on Arizona devices
The Wolfson Arizona platform is used for a range of low power audio hub
CODECs. Many of these devices feature an integrated power supply for the
microphone which is supported by this driver.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-20 11:46:19 +01:00
Axel Lin 8386a00f14 regulator: tps6524x: Fix get_voltage_sel for fixed voltage
get_voltage_sel() should return selector rather than voltage.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-20 11:20:24 +01:00
Axel Lin baf73e2c4e regulator: lp872x: Return -EINVAL if pdata is NULL
Return -EINVAL if pdata is NULL, otherwise we have NULL dereference bug.
This patch also moves the code checking pdata earlier in lp872x_probe.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-20 11:18:38 +01:00
Yadwinder Singh Brar f503071b03 regulator: max77686: Implement .set_ramp_delay() callback
This patch implements the .set_ramp_delay callback to set the ramp_delay on
hardware for BUCK2/3/4 if ramp_delay is set in regulator constraints.

This patch also do some cleaning work for unrequired members of
struct max77686_data.

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-20 11:15:13 +01:00
Axel Lin c59d2a6b20 regulator: max77686: Initialize regulator_config
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-20 11:13:55 +01:00
Mark Brown 809d310c7e regulator: lp872x: Don't allow modular build
Fixes link failure due to devm_gpio_request_one()

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-20 11:08:43 +01:00
Guennadi Liakhovetski 15719ccc27 regulator: extend the fixed dummy voltage regulator to accept voltage
Trivially extend the regulator_register_always_on() helper function to be
even more useful by adding a voltage parameter to it.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 23:22:30 +01:00
Guennadi Liakhovetski dfad84aeab regulator: support multiple dummy fixed regulators
Currently regulator_register_fixed() uses a constant name to register a
fixed dummy regulator. This is sufficient in principle, since there is no
reason to register multiple such regulators. The user can simply supply all
consumers in one array and use it to initialise such a regulator. However,
in some cases it can be convenient to register multiple such regulators.
This is also a prerequisite for the upcoming patch, that will add a voltage
parameter to this function. The original function is provided as a wrapper
macro.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 23:22:30 +01:00
Kim, Milo af8b5fc310 regulator: add new regulator driver for lp872x
This driver supports TI/National LP8720, LP8725 PMIC.

Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Reviewed-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 23:14:29 +01:00
Axel Lin e90a84473e regulator: tps65023: Convert tps65023_ldo_ops to regulator_[get|set]_voltage_sel_regmap
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:14:11 +01:00
Sangbeom Kim c848bc8538 regulator: s5m8767a: Support AP watchdog reset operation
The S5M8767A can't know status of ap reset.
So, After AP watchdog reset, AP can't boot normally.

Problem can be happened like below condition.
- AP Bootable lowest voltage(vdd_arm): 0.9v
- AP DVFS voltage table: 0.8v, 0.9v, 1.0v
- During AP works on lowest voltage(0.8V), watchdog reset is asserted
- AP can't boot, because vdd arm is still 0.8v

Solution
- Basic concept:
  After ap watchdog reset, GPIO configuration is changed by default value
- S5M8767A has function of voltage control with gpio (8 levels with 3 gpios)
- Set bootable voltage on level 0 -> can work with default gpio configuration
- In the probing, Change voltage control level from level 0 to level 1
- Execute normal dvfs operation on level 1
- After watchdog reset, ap gpio is set by default value
- PMIC operation mode is changed by ap reset (level1 -> level0)
- Regardless of previous vdd_arm voltage, AP always can be booted.

Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:06:32 +01:00
Yadwinder Singh Brar 852abad238 regulator: max77686: Convert driver to use regulator_set_voltage_time_sel.
This patch converts the driver to use regulator_set_voltage_time_sel() as
.set_voltage_time_sel() callback. It also sets ramp_delay as 100000 uV/us for
LDOs & normal BUCKs and 27500 uV/us(default/reset value) for BUCKs[2/3/4] in
regulator_desc[].

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:06:32 +01:00
Axel Lin a133829e66 regulator: tps65023: Convert to get_voltage_sel
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:06:26 +01:00
Axel Lin ba3bd8a301 regulator: tps65023: Convert to regulator_list_voltage_table
In current mapping table settings, min_uV/max_uV are always
equal to volt_table[0] and volt_table[table_len -1].
Thus remove min_uV and max_uV from struct tps_info.

The table based mapping with table_len == 1 means fixed voltage.
So we don't need fixed flag to differentiate if it is fixed or not.

This patch adds DCDC_FIXED_3300000_VSEL_table and DCDC_FIXED_1800000_VSEL_table
for fixed voltage cases. So we can convert tps65023_dcdc_ops to
regulator_list_voltage_table. This makes the code simpler.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:06:26 +01:00
Axel Lin 2c19ad43d1 regulator: mc13xxx: Remove mc13xxx_sw_regulator_is_enabled function
If .is_enabled callback is not implemented, regulator core assumes that the
regulator is always on. Thus we don't need mc13xxx_sw_regulator_is_enabled
function.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-19 12:06:25 +01:00
Mark Brown 0e8e5c34cf regulator: twl: Remove references to 32kHz clock from DT bindings
Due to the lack of a generic clock API we'd had the 32kHz clock in the
regulator driver but this is definitely a Linux-specific thing and now
we have a clock API hopefully the code can be moved elsewhere. Try to
avoid getting DTs deployed relying on the 32kHz clock by removing it
from the bindings, grep seems to tell me it's not currently used anyway.

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18 13:40:14 +01:00
Mark Brown 230a5a1c41 regulator: Fix double free in devm_regulator_put()
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18 13:39:42 +01:00
Mark Brown 74ea0e5992 regulator: tps65910: Don't use 0 as NULL
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18 11:12:21 +01:00
Axel Lin ea38d13fd1 regulator: core: Change the unit of ramp_delay from mV/uS to uV/uS
This change makes it possible to set ramp_delay with 0.xxx mV/uS without
truncation issue.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18 10:56:58 +01:00
Axel Lin 398715ab94 regulator: core: Support table based mapping in regulator_set_voltage_time_sel
For table based mapping, we can calculate voltage difference by below equation:
abs(rdev->desc->volt_table[new_selector] - rdev->desc->volt_table[old_selector])

Thus we can make regulator_set_voltage_time_sel work for table based mapping.

regulator_set_voltage_time_sel() only supports linear or table based mapping.
In case it is misused, also warn if neither linear nor table based mapping
is used with regulator_set_voltage_time_sel().

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18 10:56:51 +01:00
Axel Lin 086ccd4379 regulator: Fix setting constraints->ramp_delay in of_get_regulation_constraints
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-18 10:46:57 +01:00
Yadwinder Singh Brar 6f0b2c696c regulator: Add ramp_delay configuration to constraints
For some hardwares ramp_delay for BUCKs is a configurable parameter which can
be configured through DT or board file.This patch adds ramp_delay to regulator
constraints and allow user to configure it for regulators which supports this
feature, through DT or board file. It will provide two ways of setting the
ramp_delay for a regulator:
	First, by setting it as constraints in board file(for configurable
regulators) and set_machine_constraints() will take care of setting it on
hardware by calling(the provided) .set_ramp_delay() operation(callback).
	Second, by setting it as data in regulator_desc(as fixed/default
ramp_delay rate) for a regulator in driver.

regulator_set_voltage_time_sel() will give preference to
constraints->ramp_delay while reading ramp_delay rate for regulator. Similarly
users should also take care accordingly while refering ramp_delay rate(in case
of implementing their private .set_voltage_time_sel() callbacks for different
regulators).

[Rewrote subject for 80 columns -- broonie]

Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:08:52 +01:00
Axel Lin b5fb77e018 regulator: wm831x-dcdc: Convert wm831x_buckv_ops to set_voltage_sel and map_voltage
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:07:19 +01:00
Axel Lin d580cb5e78 regulator: wm831x-dcdc: Convert wm831x_buckp_ops to regulator_set_voltage_sel_regmap
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:07:19 +01:00
Axel Lin 0a4796896b regulator: wm831x-ldo: Convert to regulator_set_voltage_sel_regmap and map_voltage
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:07:19 +01:00
Axel Lin 1bd1955a1f regulator: ab3100: Convert fixed voltage to use regulator_list_voltage_linear
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:05:28 +01:00
Axel Lin 368a788769 regulator: pcf50633: Convert to regulator_set_voltage_sel_regmap and map_voltage
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:05:28 +01:00
Axel Lin 07b9e329f9 regulator: ab8500: Remove min_uV and max_uV from struct ab8500_regulator_info
The min_uV and max_uV are not really used in the code and misleading because
the min_uV and max_uV settings does not match the value in the voltage table.

For example, we have
static const unsigned int ldo_vaux3_voltages[] = {
        1200000,
        1500000,
        1800000,
        2100000,
        2500000,
        2750000,
        2790000,
        2910000,
};

With below min_uV/max_uV settings for AB8500_LDO_AUX3.
.min_uV                 = 1100000,
.max_uV                 = 3300000,

The min_uV/max_uV for AB8500_LDO_AUX3 seems copy-paste from AB8500_LDO_AUX2
and is wrong.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:04:45 +01:00
Axel Lin 7142e2138b regulator: ab8500: Use regulator_list_voltage_linear for ab8500_regulator_fixed_ops
Also removes set_voltage_time_sel callback from ab8500_regulator_fixed_ops
because the voltage won't change. ( And ab8500_regulator_fixed_ops does not
implement get_voltage_sel so set_voltage_time_sel won't be called )

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:04:45 +01:00
Axel Lin 34e74f39fa regulator: mc13xxx: Convert to regulator_list_voltage_table
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:01:21 +01:00
Axel Lin ee5e6253ac regulator: mc13xxx: Fix voltage checking for mc13xxx_fixed_regulator_set_voltage
The voltage range checking should be to ensure mc13xxx_regulators[id].voltages[0]
falls with min_uV and max_uV.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-06-17 21:01:21 +01:00