kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
changed 'unsigned' to 'unsigned int' to obtain the coding style.
Signed-off-by: Jannik Becher <Becher.Jannik@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This is part of a final push to convert all drivers to g/s_selection.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in streaming the camera data.
It has a single work item(&dev->work_struct) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Frank Zago <frank@zago.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in streaming the camera data.
It has a single work item(&sd->work_struct) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in streaming the camera data.
It has a single work item(&sd->work_struct) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in updating the JPEG quality
of the gspca_dev. It has a single work item(&sd->work) and hence doesn't
require ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "workqueue" is involved in polling the pvrusb2 hardware
(pvr2_hdw).
It has a single work item(&hdw->workpoll) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in pvr2_hdw_destroy to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Sometimes, the USB pipe could enter into a stalled state,
and may need a reset to rework.
Add such logic.
[mchehab@osg.samsung.com: ported from Android's source:
3a322adc00%5E%21]
Signed-off-by: Terry Heo <terryheo@google.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
Fix a memory leak on probe error of the airspy usb device driver.
The problem is triggered when more than 64 usb devices register with
v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.
The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.
A badusb device can emulate 64 of these devices, and then through
continual emulated connect/disconnect of the 65th device, cause the
kernel to run out of RAM and crash the kernel, thus causing a local DOS
vulnerability.
Fixes CVE-2016-5400
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch addresses CVE-2016-5400, a local DOS vulnerability caused by
a memory leak in the airspy usb device driver.
The vulnerability is triggered when more than 64 usb devices register
with v4l2 of type VFL_TYPE_SDR or VFL_TYPE_SUBDEV.A badusb device can
emulate 64 of these devices then through continual emulated
connect/disconnect of the 65th device, cause the kernel to run out of
RAM and crash the kernel.
The vulnerability exists in kernel versions from 3.17 to current 4.7.
The memory leak is caused by the probe function of the airspy driver
mishandeling errors and not freeing the corresponding control structures
when an error occours registering the device to v4l2 core.
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Cc: stable@vger.kernel.org # Up to Kernel 3.17
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The value 5 of the EEPROM_TS_MODE register (meaning dual tuner presence) is
only valid for AF9035 devices. For IT9135 devices it is invalid and led to a
false positive dual tuner mode detection with PCTV 79e.
Therefore on non-AF9035 devices and with value 5 the driver now defaults to
single tuner mode and outputs a regarding info message to log.
This fixes Bugzilla bug #118561.
Reported-by: Marc Duponcheel <marc@offline.be>
Signed-off-by: Stefan Pöschel <basic.master@gmx.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
My static checker complains that if adap->props.num_frontends is 0 then
"ret" is uninitialized. I don't think that can happen. But "ret" is
always zero here so we can just remove the condition.
This extra check was added in commit 0d3ab8410d ('[media] dvb core:
must check dvb_create_media_graph()').
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the USB ID for Terratec Cinergy S2 Rev.3 (0ccd:0102).
Curiously dvb-usb-ids included already the USB ID for TERRATEC_CINERGY_S2_R3 even if the device was not supported.
Reported-by: Christian Knippel <namerp@googlemail.com>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The DW2102 DVB-S/S2 driver uses the info() logging function from
dvb-usb.h. This function already appends a newline to the provided log
message, causing the dmesg output from DW2102 to include blank lines.
Fix this by removing the newline in the calls to info().
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When disconnecting the usbtv device, the sound card is unregistered
from ALSA and the snd member of the usbtv struct is set to NULL. If
the usbtv snd_trigger work is running, this can cause a race condition
where the kernel will attempt to access free'd resources, shown in
[1].
This patch fixes the disconnection code by cancelling any snd_trigger
work before unregistering the sound card from ALSA and checking that
the snd member still exists in the work function.
[1]:
usb 3-1.2: USB disconnect, device number 6
BUG: unable to handle kernel NULL pointer dereference at 0000000000000008
IP: [<ffffffff81093850>] process_one_work+0x30/0x480
PGD 405bbf067 PUD 405bbe067 PMD 0
Call Trace:
[<ffffffff81093ce8>] worker_thread+0x48/0x4e0
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81093ca0>] ? process_one_work+0x480/0x480
[<ffffffff81099998>] kthread+0xd8/0xf0
[<ffffffff815c73c2>] ret_from_fork+0x22/0x40
[<ffffffff810998c0>] ? kthread_worker_fn+0x170/0x170
---[ end trace 0f3dac5c1a38e610 ]---
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Tested-by: Peter Sutton <foxxy@foxdogstudios.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This op is deprecated and should not be used anymore.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Converts the dtt200u DVB USB driver over to the rc-core
infrastructure for its handling of IR remotes. This device can receive
generic NEC / NEC Extended signals and the switch to the newer core
enables the easy use of tools such as ir-keytable to modify the active
key map.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in updating parameters for
transfers. It has a single work item(&sd->work) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced with
the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXefulAAoJEHm+PkMAQRiG6nMH/2O1vcZeOtqmx2yCMUeXyKAT
wG88XflXzf3rM7C7TiObEYVf/bbLleJ7saDLEeic7ButD5gyYacIuzylVnrcqfBc
vinz4cOw5kvu9DrRkCKdOfiTAgwYtqQW+syJ8ZK4lPQuSxnPAs+F/FKSOpyUF5FN
Dngr520KjYKBEtn27W9UDPChFRwQoWAlaOC534eusaArCJtHGHHiuq5TEDn2EIo8
pUw2vwx5JiquSHOY34WLU7r+QoilovCQlUSsBQdLlPjfMB1QFtclPYa+5yEMjkT4
wusOUOfS/zK0rV6KnEdc/SkpiVX5C9WpFiWUOdEeJ5mZ+KijVkaOa9K1EDx8jSM=
=7Hwh
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rc6' into patchwork
Linux 4.7-rc6
* tag 'v4.7-rc6': (1245 commits)
Linux 4.7-rc6
ovl: warn instead of error if d_type is not supported
MIPS: Fix possible corruption of cache mode by mprotect.
locks: use file_inode()
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
namespace: update event counter when umounting a deleted dentry
9p: use file_dentry()
lockd: unregister notifier blocks if the service fails to come up completely
ACPI,PCI,IRQ: correct operator precedence
fuse: serialize dirops by default
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
powerpc: Initialise pci_io_base as early as possible
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
...
Patrick Keshishian improved the explanation of the protocol when porting
the driver to OpenBSD. Given it's a reverse engineering one and there's
no documetnation it might be helpful to whoever hacks on the driver.
Signed-off-by: Patrick Keshishian <sidster@boxsoft.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
OpenBSD would like to reuse some code but consider the licensing not
clear enough. Let's clarify it a bit so that it suits their conventions:
1.) Keep the "extra text" away from the copyright statement and the
rights grant.
2.) Add the warranty disclaimer -- it should not be legally required,
nevertheless the clause 1. of the rights grant refest to it.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Federico Simoncelli <fsimonce@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When CONFIG_INPUT is disabled, multiple gspca backend drivers
print compile-time warnings about unused variables:
media/usb/gspca/cpia1.c: In function 'sd_stopN':
media/usb/gspca/cpia1.c:1627:13: error: unused variable 'sd' [-Werror=unused-variable]
media/usb/gspca/konica.c: In function 'sd_stopN':
media/usb/gspca/konica.c:246:13: error: unused variable 'sd' [-Werror=unused-variable]
This annotates the variables as __maybe_unused, to let the compiler
know that they are declared intentionally.
Fixes: ee186fd96a ("[media] gscpa_t613: Add support for the camera button")
Fixes: c2f644aeeb ("[media] gspca_cpia1: Add support for button")
Fixes: b517af7228 ("V4L/DVB: gspca_konica: New gspca subdriver for konica chipset using cams")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "workqueue" is involved in transmitting hdpvr buffers.
It has a single work item(&dev->worker) and hence doesn't require
ordering. Also, it is not being used on a memory reclaim path. Hence,
the singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in hdpvr_device_release() to ensure
that there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The workqueue "work_thread" is involved in JPEG quality update.
It has a single work item(&sd->work) and hence doesn't require ordering.
Also, it is not being used on a memory reclaim path. Hence, the
singlethreaded workqueue has been replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
Work item has been flushed in sd_stop0() to ensure that there are no
pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
v4l2-compliance fails with this message:
fail: v4l2-test-buffers.cpp(250): \
timestamp != V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC && \
timestamp != V4L2_BUF_FLAG_TIMESTAMP_COPY
...
test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: FAIL
When setting the frame time, gspca uses v4l2_get_timestamp() which uses
ktime_get_ts() which uses ktime_get_ts64() which returns a monotonic
timestamp, so it's safe to initialize the buffer flags to
V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC to fix the failure.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
According to v4l2-compliance VIDIOC_ENUM_FRAMEINTERVALS should fail for
unsupported frame sizes, but gspca is too tolerant and tries to find
the frame intervals for the frame size nearest to the requested one.
This makes v4l2-compliance fail with this message:
fail: v4l2-test-formats.cpp(123): \
found frame intervals for invalid size 321x240
test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: FAIL
Fix this by using an exact match for the frame size when enumerating
frame intervals, and retuning an error if the frame size for which the
frame intervals have been asked is not supported.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The name wxh_to_nearest_mode() reflects better what the function does.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Set the frame _interval_ type to V4L2_FRMIVAL_TYPE_DISCRETE instead of
using V4L2_FRMSIZE_TYPE_DISCRETE which is meant for frame _size_.
The old and new values happen to be the same so there is no functional
change.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When writing the change in commit dcc7fdbec5 ("[media] gspca:
ov534/topro: prevent a division by 0") I used magic numbers for the
default framerate to minimize the code footprint to make it easier to
backport the patch to the stable trees.
However it's better if the default framerate has its own define to avoid
risking using different values in different places, and for readability.
While at it also remove some trivial comments about the framerates which
don't add much to the code anymore.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The pwc driver causes a warning when CONFIG_USB_PWC_INPUT_EVDEV is unset:
drivers/media/usb/pwc/pwc-if.c: In function 'usb_pwc_probe':
drivers/media/usb/pwc/pwc-if.c:1115:1: warning: label 'err_video_unreg' defined but not used [-Wunused-label]
This moves the unused label and code inside another #ifdef to
get rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If *nplanes is not zero, it should use the requested size if valid
Signed-off-by: Helen Koike <helen.koike@collabora.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about an unused table:
drivers/media/usb/em28xx/em28xx-dvb.c:907:38: warning: 'pctv_461e_m88ds3103_config' defined but not used [-Wunused-const-variable=]
static const struct m88ds3103_config pctv_461e_m88ds3103_config = {
^~~~~~~~~~~~~~~~~~~~~~~~~~
That's a left over of patch 76b91be3d3 ('em28xx: PCTV 461e use I2C
client for demod and SEC').
Remove the dead code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The header file has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mc5602_s5k4aa.h has some private static structures that
are used only by the C file. Move those structures to the C file,
in order to shut up gcc 6.1 warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mc5602_brigde.h is included at m5602 submodules. This
causes Gcc 6.1 to complain:
drivers/media/usb/gspca/m5602/m5602_bridge.h:124:28: warning: 'sensor_urb_skeleton' defined but not used [-Wunused-const-variable=]
static const unsigned char sensor_urb_skeleton[] = {
^~~~~~~~~~~~~~~~~~~
drivers/media/usb/gspca/m5602/m5602_bridge.h:119:28: warning: 'bridge_urb_skeleton' defined but not used [-Wunused-const-variable=]
static const unsigned char bridge_urb_skeleton[] = {
^~~~~~~~~~~~~~~~~~~
Let's shut up gcc 6.1 warnings by moving those data structures
to the core, as they're used only there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Gcc 6.1 warns about some unused vars. Remove them:
drivers/media/usb/usbvision/usbvision-core.c:94:18: warning: 'min_imgheight' defined but not used [-Wunused-const-variable=]
static const int min_imgheight = MIN_FRAME_HEIGHT;
^~~~~~~~~~~~~
drivers/media/usb/usbvision/usbvision-core.c:93:18: warning: 'min_imgwidth' defined but not used [-Wunused-const-variable=]
static const int min_imgwidth = MIN_FRAME_WIDTH;
^~~~~~~~~~~~
drivers/media/usb/usbvision/usbvision-core.c:92:18: warning: 'max_imgheight' defined but not used [-Wunused-const-variable=]
static const int max_imgheight = MAX_FRAME_HEIGHT;
^~~~~~~~~~~~~
drivers/media/usb/usbvision/usbvision-core.c:91:18: warning: 'max_imgwidth' defined but not used [-Wunused-const-variable=]
static const int max_imgwidth = MAX_FRAME_WIDTH;
^~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
struct media_devnode is currently embedded at struct media_device.
While this works fine during normal usage, it leads to a race
condition during devnode unregister. the problem is that drivers
assume that, after calling media_device_unregister(), the struct
that contains media_device can be freed. This is not true, as it
can't be freed until userspace closes all opened /dev/media devnodes.
In other words, if the media devnode is still open, and media_device
gets freed, any call to an ioctl will make the core to try to access
struct media_device, with will cause an use-after-free and even GPF.
Fix this by dynamically allocating the struct media_devnode and only
freeing it when it is safe.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The uvc compat ioctl implementation seems to have copied user data
for no good reason. Remove a bunch of copies.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
The current code goes through a lot of indirection just to call a
known handler. Simplify it: just call the handlers directly.
Cc: stable@vger.kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
The code is checking for negative returns but it should be checking for
zero.
Fixes: aab3125c43 ('[media] em28xx: add support for registering multiple i2c buses')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove __func__ and KBUILD_MODNAME from logging formatters and pass
USB interface device instead, so logging can be done correctly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The MXL5007T tuner will lock-up on some devices after an I2C read
transaction. This patch works around this issue by inhibiting such
operations and emulating a 0x00 response. The workaround is only
applied to USB devices known to exhibit this flaw.
Signed-off-by: Alessandro Radicati <alessandro@radicati.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch will modify the af9035 driver to use the register address
fields of the I2C read command for the combined write/read transaction
case. Without this change, the firmware issues just a I2C read
transaction without the preceding write transaction to select the
register.
Signed-off-by: Alessandro Radicati <alessandro@radicati.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This adds the missing auto-select bits for DVB-frontends and tuners
(if MEDIA_SUBDRV_AUTOSELECT is enabled) which are used by the various
rtl28xxu devices.
The driver itself probes for three more tuners, but it's not actually
using any of them:
- MEDIA_TUNER_MT2063
- MEDIA_TUNER_MT2266
- MEDIA_TUNER_MXL5007T
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
1 and 2 wasn't enough for mn88472 chip on Astrometa device,
so increase it to 3.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The formula used to calculate bytesperline only works for packed format.
So far, all planar format we support have their bytesperline equal to
the image width (stride of the Y plane or a line of Y for M420).
Signed-off-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Pull string hash improvements from George Spelvin:
"This series does several related things:
- Makes the dcache hash (fs/namei.c) useful for general kernel use.
(Thanks to Bruce for noticing the zero-length corner case)
- Converts the string hashes in <linux/sunrpc/svcauth.h> to use the
above.
- Avoids 64-bit multiplies in hash_64() on 32-bit platforms. Two
32-bit multiplies will do well enough.
- Rids the world of the bad hash multipliers in hash_32.
This finishes the job started in commit 689de1d6ca ("Minimal
fix-up of bad hashing behavior of hash_64()")
The vast majority of Linux architectures have hardware support for
32x32-bit multiply and so derive no benefit from "simplified"
multipliers.
The few processors that do not (68000, h8/300 and some models of
Microblaze) have arch-specific implementations added. Those
patches are last in the series.
- Overhauls the dcache hash mixing.
The patch in commit 0fed3ac866 ("namei: Improve hash mixing if
CONFIG_DCACHE_WORD_ACCESS") was an off-the-cuff suggestion.
Replaced with a much more careful design that's simultaneously
faster and better. (My own invention, as there was noting suitable
in the literature I could find. Comments welcome!)
- Modify the hash_name() loop to skip the initial HASH_MIX(). This
would let us salt the hash if we ever wanted to.
- Sort out partial_name_hash().
The hash function is declared as using a long state, even though
it's truncated to 32 bits at the end and the extra internal state
contributes nothing to the result. And some callers do odd things:
- fs/hfs/string.c only allocates 32 bits of state
- fs/hfsplus/unicode.c uses it to hash 16-bit unicode symbols not bytes
- Modify bytemask_from_count to handle inputs of 1..sizeof(long)
rather than 0..sizeof(long)-1. This would simplify users other
than full_name_hash"
Special thanks to Bruce Fields for testing and finding bugs in v1. (I
learned some humbling lessons about "obviously correct" code.)
On the arch-specific front, the m68k assembly has been tested in a
standalone test harness, I've been in contact with the Microblaze
maintainers who mostly don't care, as the hardware multiplier is never
omitted in real-world applications, and I haven't heard anything from
the H8/300 world"
* 'hash' of git://ftp.sciencehorizons.net/linux:
h8300: Add <asm/hash.h>
microblaze: Add <asm/hash.h>
m68k: Add <asm/hash.h>
<linux/hash.h>: Add support for architecture-specific functions
fs/namei.c: Improve dcache hash function
Eliminate bad hash multipliers from hash_32() and hash_64()
Change hash_64() return value to 32 bits
<linux/sunrpc/svcauth.h>: Define hash_str() in terms of hashlen_string()
fs/namei.c: Add hashlen_string() function
Pull out string hash to <linux/stringhash.h>
The "simplified" prime multipliers made very bad hash functions, so get rid
of them. This completes the work of 689de1d6ca.
To avoid the inefficiency which was the motivation for the "simplified"
multipliers, hash_64() on 32-bit systems is changed to use a different
algorithm. It makes two calls to hash_32() instead.
drivers/media/usb/dvb-usb-v2/af9015.c uses the old GOLDEN_RATIO_PRIME_32
for some horrible reason, so it inherits a copy of the old definition.
Signed-off-by: George Spelvin <linux@sciencehorizons.net>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge updates from Andrew Morton:
- fsnotify fix
- poll() timeout fix
- a few scripts/ tweaks
- debugobjects updates
- the (small) ocfs2 queue
- Minor fixes to kernel/padata.c
- Maybe half of the MM queue
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm, page_alloc: restore the original nodemask if the fast path allocation failed
mm, page_alloc: uninline the bad page part of check_new_page()
mm, page_alloc: don't duplicate code in free_pcp_prepare
mm, page_alloc: defer debugging checks of pages allocated from the PCP
mm, page_alloc: defer debugging checks of freed pages until a PCP drain
cpuset: use static key better and convert to new API
mm, page_alloc: inline pageblock lookup in page free fast paths
mm, page_alloc: remove unnecessary variable from free_pcppages_bulk
mm, page_alloc: pull out side effects from free_pages_check
mm, page_alloc: un-inline the bad part of free_pages_check
mm, page_alloc: check multiple page fields with a single branch
mm, page_alloc: remove field from alloc_context
mm, page_alloc: avoid looking up the first zone in a zonelist twice
mm, page_alloc: shortcut watermark checks for order-0 pages
mm, page_alloc: reduce cost of fair zone allocation policy retry
mm, page_alloc: shorten the page allocator fast path
mm, page_alloc: check once if a zone has isolated pageblocks
mm, page_alloc: move __GFP_HARDWALL modifications out of the fastpath
mm, page_alloc: simplify last cpupid reset
mm, page_alloc: remove unnecessary initialisation from __alloc_pages_nodemask()
...
A few instances of "fimware" instead of "firmware" were found. Fix
these and add it to the spelling.txt file.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull i2c updates from Wolfram Sang:
- Peter Rosin did some major rework on the locking of i2c muxes by
seperating parent-locked muxes and mux-locked muxes.
This avoids deadlocks/workarounds when the mux itself needs i2c
commands for muxing. And as a side-effect, other workarounds in the
media layer could be eliminated. Also, Peter stepped up as the i2c
mux maintainer and will keep an eye on these changes.
- major updates to the octeon driver
- add a helper to the core to generate the address+rw_bit octal and
make drivers use it
- quite a bunch of driver updates
* 'i2c/for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (84 commits)
i2c: rcar: add DMA support
i2c: st: Implement bus clear
i2c: only check scl functions when using generic recovery
i2c: algo-bit: declare i2c_bit_quirk_no_clk_stretch as static
i2c: tegra: disable clock before returning error
[media] rtl2832: regmap is aware of lockdep, drop local locking hack
[media] rtl2832_sdr: get rid of empty regmap wrappers
[media] rtl2832: change the i2c gate to be mux-locked
[media] si2168: change the i2c gate to be mux-locked
iio: imu: inv_mpu6050: change the i2c gate to be mux-locked
i2c: mux: document i2c muxes and elaborate on parent-/mux-locked muxes
i2c: mux: relax locking of the top i2c adapter during mux-locked muxing
i2c: muxes always lock the parent adapter
i2c: allow adapter drivers to override the adapter locking
i2c: uniphier: add "\n" at the end of error log
i2c: mv64xxx: remove CONFIG_HAVE_CLK conditionals
i2c: mv64xxx: use clk_{prepare_enable,disable_unprepare}
i2c: mv64xxx: handle probe deferral for the clock
i2c: mv64xxx: enable the driver on ARCH_MVEBU
i2c: octeon: Add workaround for broken irqs on CN3860
...
Hauppauge WinTV-dualHD is a USB 2.0 dual DVB-T/T2/C tuner with
following components:
USB bridge: Empia EM28274 (chip id is the same as EM28174)
Demodulator: 2x Silicon Labs Si2168-B40
Tuner: 2x Silicon Labs Si2157-A30
This patch adds support only for the first tuner.
The demodulator needs firmware, available for example here:
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/4.0.11/
The demodulators sit on the same I2C bus and their addresses
are 0x64 and 0x67. The tuners are behind the demodulators and
their addresses are 0x60 and 0x63.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828_v4l2_device_register() unlocks au0828_dev->lock and frees au0828
dev in error legs before return. au0828_usb_probe() does the same when
au0828_v4l2_device_register() returns error.
Fix au0828_v4l2_device_register() to not to unlock and free in its error
legs.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A couple of data structures in the dibusb-common file are only
accessed when CONFIG_DVB_DIB3000MC is enabled, otherwise we
get a harmless gcc warning:
usb/dvb-usb/dibusb-common.c:223:34: error: 'dib3000p_panasonic_agc_config' defined but not used
usb/dvb-usb/dibusb-common.c:211:32: error: 'stk3000p_dib3000p_config' defined but not used
This moves the existing #ifdef a few lines up to correctly cover
all the conditional data structures, which gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PX-BCUD has the following components:
USB interface: Empia EM28178
Demodulator: Toshiba TC90532 (works by code for TC90522)
Tuner: Next version of Sharp QM1D1C0042
em28xx_dvb_init(): add init code for PLEX PX-BCUD with calling
px_bcud_init() that does things like pin configuration.
qm1d1c0042_init(): support the next version of QM1D1C0042, change to
choose an appropriate array of initial registers by reading chip id.
[mchehab@osg.samsung.com: fold a fixup patch and fix checkpatch.pl
errors/warnings, where applicable]
Signed-off-by: Satoshi Nagahama <sattnag@aim.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Another version of Elgato EyeTV Sat USB DVB-S2 adapter needs just
a USB ID addition.
Signed-off-by: Christian Knippel <namerp@gmail.com>
Reported-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, dw2102 assumes that the USB IDs will be either at
an external header or defined internally. That doesn't sound
right.
So, let's move the definitions to just one place.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The root i2c adapter lock is then no longer held by the i2c mux during
accesses behind the i2c gate, and such accesses need to take that lock
just like any other ordinary i2c accesses do.
So, declare the i2c gate mux-locked, and zap the regmap overrides
that makes the i2c accesses unlocked and use plain old regmap
accesses. This also removes the need for the regmap wrappers used by
rtl2832_sdr, so deconvolute the code further and provide the regmap
handle directly instead of the wrapper functions.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXJoi6AAoJEHm+PkMAQRiGYKIIAIcocIV48DpGAHXFuSZbzw5D
rp9EbE5TormtddPz1J1zcqu9tl5H8tfxS+LvHqRaDXqQkbb0BWKttmEpKTm9mrH8
kfGNW8uwrEgTMMsar54BypAMMhHz4ITsj3VQX5QLSC5j6wixMcOmQ+IqH0Bwt3wr
Y5JXDtZRysI1GoMkSU7/qsQBjC7aaBa5VzVUiGvhV8DdvPVFQf73P89G1vzMKqb5
HRWbH4ieu6/mclLvW9N2QKGMHQntlB+9m2kG9nVWWbBSDxpAotwqQZFh3D52MBUy
6DH/PNgkVyDhX4vfjua0NrmXdwTfKxLWGxe4dZ8Z+JZP5c6pqWlClIPBCkjHj50=
=KLSM
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc6' into patchwork
Linux 4.6-rc6
* tag 'v4.6-rc6': (762 commits)
Linux 4.6-rc6
EDAC: i7core, sb_edac: Don't return NOTIFY_BAD from mce_decoder callback
Documentation/sysctl/vm.txt: update numa_zonelist_order description
lib/stackdepot.c: allow the stack trace hash to be zero
rapidio: fix potential NULL pointer dereference
mm/memory-failure: fix race with compound page split/merge
ocfs2/dlm: return zero if deref_done message is successfully handled
Ananth has moved
kcov: don't profile branches in kcov
kcov: don't trace the code coverage code
mm: wake kcompactd before kswapd's short sleep
.mailmap: add Frank Rowand
mm/hwpoison: fix wrong num_poisoned_pages accounting
mm: call swap_slot_free_notify() with page lock held
mm: vmscan: reclaim highmem zone if buffer_heads is over limit
numa: fix /proc/<pid>/numa_maps for THP
mm/huge_memory: replace VM_NO_THP VM_BUG_ON with actual VMA check
mailmap: fix Krzysztof Kozlowski's misspelled name
thp: keep huge zero page pinned until tlb flush
mm: exclude HugeTLB pages from THP page_mapped() logic
...
We print an uninitialized "actlen" variable on the error path.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Allocate an explicit i2c mux core to handle parent and child adapters
etc. Update the select op to be in terms of the i2c mux core instead
of the child adapter.
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The v4l2_device_call_* defines filter subdevs based on the grp_id value.
But some drivers use a bitmask, so instead of filtering by grp_id == value,
you want to filter by grp_id & value.
Make variants of these defines to do this.
The 'has_op' define has been extended to have a grp_id argument as well, and
a mask variant has been added.
This extra argument required a change to go7007.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 588afcc1c0 ("[media] usbvision fix overflow of interfaces
array")' should be reverted, because:
* "!dev->actconfig->interface[ifnum]" won't catch a case where the value
is not NULL but some garbage. This way the system may crash later with
GPF.
* "(ifnum >= USB_MAXINTERFACES)" does not cover all the error
conditions. "ifnum" should be compared to "dev->actconfig->
desc.bNumInterfaces", i.e. compared to the number of "struct
usb_interface" kzalloc()-ed, not to USB_MAXINTERFACES.
* There is a "struct usb_device" leak in this error path, as there is
usb_get_dev(), but no usb_put_dev() on this path.
* There is a bug of the same type several lines below with number of
endpoints. The code is accessing hard-coded second endpoint
("interface->endpoint[1].desc") which may not exist. It would be great
to handle this in the same patch too.
* All the concerns above are resolved by already-accepted commit fa52bd50
("[media] usbvision: fix crash on detecting device with invalid
configuration")
* Mailing list message:
http://www.spinics.net/lists/linux-media/msg94832.html
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.5
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
These are false positives, but still easy to fix.
pvrusb2-hdw.c:3676 pvr2_send_request_ex() error: we previously assumed 'write_data' could be null (see line 3648)
pvrusb2-hdw.c:3829 pvr2_send_request_ex() error: we previously assumed 'read_data' could be null (see line 3649)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
An V4L2_CID_PRIVATE_SHARPNESS macro is defined in the au0828 driver, but
never used. Remove it.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On the particular case when the product id is 0x2101 we have requested
for a firmware but after processing it we missed releasing it.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When we returned on error we missed freeing p_current_fw and p_buffer.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If au0828 gets removed, we need to remove the notifiers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Extending the lifetime of the media_device struct is not handled well
by the core, as it will erase some data from the struct, when
media_device_cleanup() is called after unregistering it.
While we have a fixup patch for it already, the usage of those new
functions are needed only when we share data with other drivers.
So, better to revert the changes.
This reverts commit 182dde7c5d ("[media] media: au0828 change
to use Managed Media Controller API")
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The au0828 dev_state is actually a bit mask. It should not be
checking with "==" but, instead, with a logic and. There are some
places where it was doing it wrong.
Fix that by replacing the dev_state set/clear/test with the
bitops.
As reviewed by Shuah:
"Looks good. Tested running bind/unbind au0828 loop for 1000 times.
Didn't see any problems and the v4l2_querycap() problem has been
fixed with this patch.
After the above test, ran bind/unbind snd_usb_audio 1000 times.
Didn't see any problems. Generated media graph and the graph
looks good."
Cc: stable@vger.kernel.org
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
au0828_v4l2_close() check for dev_state == DEV_DISCONNECTED will fail to
detect the device disconnected state correctly, if au0828_v4l2_open() runs
to set the DEV_INITIALIZED bit. A loop test of bind/unbind found this bug
by increasing the likelihood of au0828_v4l2_open() occurring while unbind
is in progress. When au0828_v4l2_close() fails to detect that the device
is in disconnect state, it attempts to power down the device and fails with
the following general protection fault:
[ 260.992962] Call Trace:
[ 260.993008] [<ffffffffa0f80f0f>] ? xc5000_sleep+0x8f/0xd0 [xc5000]
[ 260.993095] [<ffffffffa0f6803c>] ? fe_standby+0x3c/0x50 [tuner]
[ 260.993186] [<ffffffffa0ef541c>] au0828_v4l2_close+0x53c/0x620 [au0828]
[ 260.993298] [<ffffffffa0d08ec0>] v4l2_release+0xf0/0x210 [videodev]
[ 260.993382] [<ffffffff81570f9c>] __fput+0x1fc/0x6c0
[ 260.993449] [<ffffffff815714ce>] ____fput+0xe/0x10
[ 260.993519] [<ffffffff8116eb83>] task_work_run+0x133/0x1f0
[ 260.993602] [<ffffffff810035d0>] exit_to_usermode_loop+0x140/0x170
[ 260.993681] [<ffffffff810061ca>] syscall_return_slowpath+0x16a/0x1a0
[ 260.993754] [<ffffffff82835fb3>] entry_SYSCALL_64_fastpath+0xa6/0xa8
Cc: stable@vger.kernel.org
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix to clear enable/disable/change source handlers in the media device
when media device is unregistered in au0828_unregister_media_device().
When au0828 module is removed, snd-usb-audio shouldn't call the handlers.
Clearing will ensure snd-usb-audio won't call them once au0828 is removed.
[mchehab@osg.samsung.com: fix a compilation breakage]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For au0828_enable_source() to work, the tuner links should be
disabled and the tuner/decoder should be cached at au0828 struct.
While here, put dev->decoder cache together with dev->tuner, as
it makes easier to drop both latter if/when we move the enable
routines to the V4L2 core.
Fixes: 9822f4173f ('[media] au0828: use v4l2_mc_create_media_graph()')
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Tested-by: Shuah Khan <shuahkh@osg.samsung.com>
Disable tuner to demod link in au0828_media_device_register(). This step
should be done after dvb graph is created.
[mchehab@osg.samsung.com: Solve conflictst to apply it upstream]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes those two smatch warnings:
drivers/media/usb/gspca/touptek.c:206 val_reply() warn: argument 3 to %02x specifier has type 'char'
drivers/media/usb/gspca/touptek.c:222 reg_w() warn: argument 4 to %02x specifier has type 'char'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As warned by smatch:
drivers/media/usb/gspca/touptek.c:220 reg_w() error: doing dma on the stack (buff)
drivers/media/usb/gspca/touptek.c:458 configure() error: doing dma on the stack (buff)
This can fail, as the stack may not be in a memory that would
allod DMA. So, use the usb_buf instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Some functions in the au0828 driver are only used when CONFIG_MEDIA_CONTROLLER
is enabled, and otherwise defined as empty functions:
media/usb/au0828/au0828-core.c:208:13: error: 'au0828_media_graph_notify' defined but not used [-Werror=unused-function]
media/usb/au0828/au0828-core.c:262:12: error: 'au0828_enable_source' defined but not used [-Werror=unused-function]
media/usb/au0828/au0828-core.c:412:13: error: 'au0828_disable_source' defined but not used [-Werror=unused-function]
This moves the #ifdef so the entire definitions are hidden in this case.
[mchehab@osg.samsung.com: As pointed by Shuah Khan, a return 0 can be removed]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
EMP202 chip inside Terratec Grabby (hw rev 2) seems to require some time
before accessing reliably its registers. Otherwise it returns some values
previously put on the I2C bus.
To account for that period, we delay card setup until we have a proof that
accessing AC97 registers is reliable. We get this proof by polling
AC97_RESET until the expected value is read. We also check that unrelated
registers don't return the same value. This second check handles the case
where the expected value is constantly returned no matter which register
is accessed.
Signed-off-by: Matthieu Rogez <matthieu.rogez@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When snd_usb_audio gets probed first, audio mixer doesn't get linked to
the decoder.
Change au0828_media_graph_notify() to handle the mixer entity getting
registered before the decoder.
Change au0828_media_device_register() to invoke
au0828_media_graph_notify() to connect entites that were created prior
to registering the notify handler.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Reported-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
TeVii S662 is a USB 2.0 DVB-S2 tuner that's identical to TechnoTrend
S2-4600 tuner. Add the USB ID to dw2102 driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ts2020.h was already included a few lines earlier. Remove the unnecessary entry.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Terratec Grabby (hw rev 2) Record led is connected to GPIO 3
and its logic is inverted: (PIO3 = 0: on, PIO3 = 1: off).
Signed-off-by: Matthieu Rogez <matthieu.rogez@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cleanup that changed the em28xx driver to use v4l2_mc_create_media_graph
instead of its own implementation causes a build error when CONFIG_MEDIA_CONTROLLER
is disabled:
drivers/media/usb/em28xx/em28xx-video.c: In function 'em28xx_v4l2_init':
drivers/media/usb/em28xx/em28xx-video.c:2717:38: error: 'struct em28xx' has no member named 'media_dev'
This puts the new code inside the same #ifdef that controls the presence
of the 'media_dev' member, and that the old code was in.
Fixes: de39078779 ("[media] em2xx: use v4l2_mc_create_media_graph()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change vidioc_s_input() to enable the media source for the newly
selected input.
v4l2-core enables source before calling au0828's vidioc_s_input()
handler. Hence, when input selection changes, media source for the
newly selected input needs to be enabled.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Convert the TT S2-4600 USB tuner to use the I2C binding for attaching
the demodulator instead of the old m88ds3103_attach method.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add callback parameter to select enable / disable slave TS and use
it when slave demod is in use.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dev->ctrl_input is set in vidioc_s_input() and doesn't get set in
au0828_s_input(). As a result, dev->ctrl_input is left uninitialized
until user space calls s_input.
It works correctly because the default input value is 0 and which is
what dev->ctrl_input gets initialized via kzalloc().
Change to set dev->ctrl_input in au0828_s_input(). Also optimize
vidioc_s_input() to return if the new input value is same as the
current.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for Intel R200 depth camera in uvc driver.
This includes adding new uvc GUIDs for the new pixel formats,
adding new V4L pixel format definition to user api headers,
and updating the uvc driver GUID-to-4cc tables with the new formats.
Tested-by: Greenberg, Aviv D <aviv.d.greenberg@intel.com>
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There's no reason to implement its own function to create the
media graph. So, use the core one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As we want au0828 to use the core function to create the MC
graphs, use enum demod_pad_index instead of
enum au8522_media_pads.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As warned by smatch:
drivers/media/usb/dvb-usb/technisat-usb2.c:263 technisat_usb2_set_led() error: doing dma on the stack (led)
drivers/media/usb/dvb-usb/technisat-usb2.c:280 technisat_usb2_set_led_timer() error: doing dma on the stack (&b)
drivers/media/usb/dvb-usb/technisat-usb2.c:341 technisat_usb2_identify_state() error: doing dma on the stack (version)
drivers/media/usb/dvb-usb/technisat-usb2.c:609 technisat_usb2_get_ir() error: doing dma on the stack (buf)
drivers/media/usb/dvb-usb/technisat-usb2.c:619 technisat_usb2_get_ir() error: doing dma on the stack (buf)
Create a buffer at the device state and use it for all the DMA
transfers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As warned by smatch:
drivers/media/usb/airspy/airspy.c:541 airspy_start_streaming() warn: test_bit() takes a bit number
drivers/media/usb/airspy/airspy.c:569 airspy_start_streaming() warn: test_bit() takes a bit number
drivers/media/usb/airspy/airspy.c:605 airspy_stop_streaming() warn: test_bit() takes a bit number
set_bit/clear_bit argument is the bit number, and not 1 << bit.
Thankfully, one of the bits was not used (URB_BUF), with would
otherwise cause a driver misfunctioning.
Clean this mess by always using set_bit/clear_bit/test_bit and
removing the unused bit.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the unused ovfx2_vga_mode/ovfx2_cif_mode arrays from the ov519
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Fix the ov519 driver not working (unable to talk to the sensor) when
plugged into a xhci host. The root cause here is that uhci/ohci/ehci
hosts typically will send any pending async requests every milli-second
and then go to sleep for the rest if the milli-second, where as xhci hosts
send them immediately, causing things to go too fast for the ov519 bridge.
This commit adds a few delays fixing this.
Signed-off-by: Wesley Post <pa4wdh@xs4all.nl>
[hdegoede@redhat.com: Also add delays to w996Xcf.c, as that needs them too]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change au0828 to check if tuner is free or not before changing tuner
configuration.
vidioc_g_tuner(), and au0828_v4l2_close() now call v4l-core interface
v4l_enable_media_source() before changing tuner configuration.
Remove au0828_enable_analog_tuner() as it is no longer needed because
v4l2-core implements common interfaces to check for media source
availability.
In addition, queue_setup() no longer needs the tuner availability check
since v4l2-core does it.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add enable_source and disable_source handlers. The enable source handler
is called from v4l2-core, dvb-core, and ALSA drivers to check if the
shared media source is free.
The disable source handler is called to release the shared media
source.
[mchehab@osg.samsung.com: fix merge conflicts]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Register entity_notify async hook to create links between existing
bridge driver entities and a newly added non-bridge driver entities. For
example, this handler creates link between V4L decoder entity and ALSA
mixer entity.
[mchehab@osg.samsung.com: fix merge conflicts and make
au0828_media_graph_notify static to shut up a warning]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change au0828_create_media_graph() to find and disable
tuner and demod link. This helps avoid an additional
disable step when tuner is requested by video or audio.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Create tuner to demod pad link in disabled state to avoid disable step
when tuner resource is requested by dvb.
[mchehab@osg.samsung.com: fix a merge conflict]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Media device initialization and registration steps are split. There is a
window between media device init and media device register during usb
probe.
au0828 bridge driver and snd-usb-audio could try to initialize the media
device, if they simply checked, whether the device has been registered.
They also need to check whether the device has been initialized.
Change the au0828-core to check if media device is already initialized
during initialization step and check if media device is already
registered during the registration step.
[mchehab@osg.samsung.com: fix a merge conflict]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change au0828 to use Managed Media Controller API to share media device
and coordinate creating/deleting the shared media device with the
snd-usb-audio driver. The shared media device is created as device
resource of the parent usb device of the two drivers.
Populate media device model with USB Device product name instead of
au0828 device board name. This change is necessary because, if the media
device is registered by the snd-usb-audio driver first, and it doesn't
know the au0828 board name.
[mchehab@osg.samsung.com: Fix merge conflicts]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change au0828-core to use au8522_media_pads enum defines
instead of hard-coding the pad values.
[mchehab@osg.samsung.com: patch rebased, as the code was
moved to au0828-video.c. Also added AU8522_PAD_INPUT to the list
of pad number replacements]
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The buffer_complete() routine assumes that sp is not NULL,
otherwise it will fail completely. Btw, this is also
assumed at pvr2_buffer_queue(), with is the routine that
setups the URB handling.
So, remove the bogus for the callback at buffer_complete.
This fix this smatch warning:
drivers/media/usb/pvrusb2/pvrusb2-io.c:476 buffer_complete() warn: variable dereferenced before check 'sp' (see line 472)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Right now, media_device_pci_init and media_device_usb_init does
media_device allocation internaly. That preents its usage when
the media_device struct is embedded on some other structure.
Move memory allocation outside it, to make it more generic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Those ancillary functions could be called even when compiled
without V4L2 support, as warned by ktest build robot:
All errors (new ones prefixed by >>):
>> ERROR: "__v4l2_mc_usb_media_device_init" [drivers/media/usb/dvb-usb/dvb-usb.ko] undefined!
>> ERROR: "__v4l2_mc_usb_media_device_init" [drivers/media/usb/dvb-usb-v2/dvb_usb_v2.ko] undefined!
>> ERROR: "__v4l2_mc_usb_media_device_init" [drivers/media/usb/au0828/au0828.ko] undefined!
Also, there's nothing there that are specific to V4L2. So, move
those ancillary functions to MC core.
No functional changes. Just function rename.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It makes sense to make the min_t() cast unsigned here since we don't
really want negative sizes. Making it signed causes a static checker
warning in Smatch. Smatch knows "fw->size - i" is positive but it
doesn't know that fw->size is less than INT_MAX so in theory casting it
to int might lead to a negative.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since kthread_run returns -ENOMEM if failed,
it needs to be checked whether it is error, not whether it is null.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, it is initializing the driver name using the wrong
name ("usb"). Use the generic function, as its logic works
best, and avoids repeating the very same code everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This macro is not used inside the driver. get rid of it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is not used on the driver. remove it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As si2157 doesn't use the subdev, but has instead a binding
logic that doesn't have any core framework, we need to manually
pass the media_device struct via platform data on every place
it is called.
This fixes support for HVR-955Q when MC is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of having its own routine, use the one defined at the
core, as it is generic enough to handle the cx231xx usecases.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When in analog mode, the RF connector will be created by
em28xx-video. However, when the device is in digital mode only,
the RF connector is not shown. In this case, let the DVB
core to create it for us.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Except for the usbuvc driver (with has an embedded media_device
struct on it), the other drivers have a pointer to media_device.
On those drivers, replace their own implementation for the core
one. That warrants that those subdev drivers will fill the
media_device info the same way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a header file for the tvp5150 input connectors constants that
can be shared between the driver and Device Tree source files.
[mchehab@osg.samsung.com: rename tvp5150.h also at em28xx-cards.c]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of having lots of #ifdefs inside au0828-core due to
V4L2, move the dependencies to au0828-video.c. That allows
removing all those ifdefs, as au0828-video is only compiled if
CONFIG_VIDEO_AU0828_V4L2.
This fixes the following warnings reported by Kbuild test
with a random config with au0828 enabled, but V4L2 is disabled.
All warnings (new ones prefixed by >>):
drivers/media/usb/au0828/au0828-core.c: In function 'au0828_usb_probe':
>> drivers/media/usb/au0828/au0828-core.c:463:1: warning: label 'done' defined but not used [-Wunused-label]
done:
^
drivers/media/usb/au0828/au0828-core.c: At top level:
drivers/media/usb/au0828/au0828-core.c:250:12: warning: 'au0828_create_media_graph' defined but not used [-Wunused-function]
static int au0828_create_media_graph(struct au0828_dev *dev)
^
Tested with a WinTV HVR 950Q (USB ID: 2040:7200)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It doesn't make sense to try to create the analog TV graph,
if the device fails to register at V4L2, or if it doesn't have
V4L2 support.
Thanks to Shuah for pointing this issue.
Reported-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that the core has a function to create the media graph,
we can get rid of the specialized code at em28xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of using the DTV properties cache directly, pass the get
frontend data as an argument. For now, everything should remain
the same, but the next patch will prevent get_frontend to
affect the global cache.
This is needed because several drivers don't care enough to only
change the properties if locked. Due to that, calling
G_PROPERTY before locking on those drivers will make them to
never lock. Ok, those drivers are crap and should never be
merged like that, but the core should not rely that the drivers
would be doing the right thing.
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver doesn't support getting frontend information and
it only works in automatic mode.
So, let's remove get_frontend() and update the cache at
set_frontend().
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When remove_pending is non-zero, v4l2_lock is never unlocked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The i2c client pointer is only used when CONFIG_I2C is set, and
otherwise produces a compile-time warning:
drivers/media/usb/hdpvr/hdpvr-core.c: In function 'hdpvr_probe':
drivers/media/usb/hdpvr/hdpvr-core.c:276:21: error: unused variable 'client' [-Werror=unused-variable]
This uses the same #ifdef to hide the variable when the code using
it is hidden.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Sometimes i2c transfer fails. That happens especially when large
amount of data is written sequentially eg. firmware download.
Problem arises with both integrated rtl2832 demod and external
mn88472 demod, which is clear indicator it is busy i2c bus issue.
Use i2c core retry logic in order fix the issue by repeating failed
message. Another solution which also works is to add ~100us delay
between i2c messages - but repeating sounds more elegant and does
not cause any extra delay for success cases.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a new product id to dvb-usb-dvbsky for new version of TechnoTrend CT2-4650 CI
Signed-off-by: Torbjörn Jansson <torbjorn.jansson@mbox200.swipnet.se>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
PIP tested with VLC. Diversity tested with the Windows driver.
Signed-off-by: Stefan Pöschel <basic.master@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Terratec Cinergy S2 USB BOX uses a Montage M88TS2022 tuner
and a M88DS3103 demodulator, same as Technotrend TT-connect S2-4600.
This patch adds the missing USB Product ID to make it work.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
dma_area needs to be freed when the device is closed.
Based on em23xx-audio.c
Signed-off-by: Jean-Baptiste Theou <jtheou@adeneo-embedded.us>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This mxl111sf_tuner_config structure is never modified, so declare it as
const.
There are some indentation changes to remain within 80 columns.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since kzalloc can be failed,
if not properly handled, NULL dereference could be happened.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since kmalloc can be failed in memory pressure,
if not properly handled, NULL dereference can be happend
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let us return directly if the element "status" of the variable "buf"
indicates "BUFSTAT_READY".
A check repetition can be excluded for the variable "ret" at the end then.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
1. Let us return directly if a buffer allocation failed.
2. Delete the jump label "err" then.
3. Drop the explicit initialisation for the variable "ret"
at the beginning.
4. Return zero as a constant at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calling vb2_set_plane_payload is enough, there's no need to
set the planes[] bytesused field. Remove it.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use to_video_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are many dropped fields with some sources, leading to many
redundant fields without counterparts. When this redundant field
is odd, a new frame is pushed containing this odd field interleaved
with whatever was left in the buffer, causing video artifacts.
Do not push a new frame after processing every odd field, but do it
only after those which come after an even field.
Signed-off-by: Nikola Forró <nikola.forro@gmail.com>
Acked-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The go7007_hpi_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The as102_priv_ops_t structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The stv6110x_devctl structure is never modified, so declare it as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some devices, like Terratec Cinergy HTC, where
while the device supports analog TV, the driver is not
capable yet of handling it, because the analog TV driver
was not written.
So, don't bind the em28xx-v4l drivers on such devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The tuner is at address 0x60. This address is not probed by
default by tuner anymore, so we need to explicitly add it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If something bad happens during device registration, unregister
the already registered devices.
Without that, it will have lots of KASAN errors when udev
would try to open the devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The output of a tuner is not only IF frequencies. They may also
output audio on some of its pins, and may even be a zero-IF tuner,
with outputs a baseband. So, rename the PAD name to make it
clearer and add a proper documentation about that at tuner.h.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The em28xx driver have lots of different input types but
only 4 of such types are actually used. The others are bogus.
Remove them, in order to cleanup the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On em28xx driver, s_stream subdev ops was not implemented
properly. It was used only to disable stream, never enabling it.
That was the root cause of the regression when we added support
for s_stream on tvp5150 driver.
With that, we can get rid of the changes on tvp5150 side,
e. g. changeset 47de9bf893 ('[media] tvp5150: Fix breakage for serial usage').
Tested video output on em2820+tvp5150 on WinTV USB2 and
video and/or vbi output on em288x+tvp5150 on HVR 950.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This issue was detected by using the Coccinelle software.
Return the value from a call of the msi2500_ctrl_msg() function
without using an extra check for the variable "ret" at the end.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Now that this was defined at usb-id.h, update the values for
USB_PID_TERRATEC_CINERGY_S2_R1 and USB_PID_TERRATEC_CINERGY_S2_R2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
MyGica/Geniatech S2870 is very similar to the S870 but with dual tuner. The card is recognised as Geniatech STK8096-PVR.
[mchehab@osg.samsung.com: Fix some checkpatch.pl issues]
Signed-off-by: Nicolas Sugino <nsugino@3way.com.ar>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Soon my dibcom.fr/parrot.com-address won't respond anymore.
Thus I'm replacing it. And, while being at it,
let's adapt some other (old) email-addresses as well.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6J4t
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull second batch of media updates from Mauro Carvalho Chehab:
"This is the second part of the media patches. It contains the media
controller next generation patches, with is the result of one year of
discussions and development. It also contains patches to enable media
controller support at the DVB subsystem.
The goal is to improve the media controller to allow proper support
for other types of Video4Linux devices (radio and TV ones) and to
extend the media controller functionality to allow it to be used by
other subsystems like DVB, ALSA and IIO.
In order to use the new functionality, a new ioctl is needed
(MEDIA_IOC_G_TOPOLOGY). As we're still discussing how to pack the
struct fields of this ioctl in order to avoid compat32 issues, I
decided to add a patch at the end of this series commenting out the
new ioctl, in order to postpone the addition of the new ioctl to the
next Kernel version (4.6).
With that, no userspace visible changes should happen at the media
controller API, as the existing ioctls are untouched. Yet, it helps
DVB, ALSA and IIO developers to develop and test the patches adding
media controller support there, as the core will contain all required
internal changes to allow adding support for devices that belong to
those subsystems"
* tag 'media/v4.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (177 commits)
[media] Postpone the addition of MEDIA_IOC_G_TOPOLOGY
[media] mxl111sf: Add a tuner entity
[media] dvbdev: create links on devices with multiple frontends
[media] media-entitiy: add a function to create multiple links
[media] dvb-usb-v2: postpone removal of media_device
[media] dvbdev: Add RF connector if needed
[media] dvbdev: remove two dead functions if !CONFIG_MEDIA_CONTROLLER_DVB
[media] call media_device_init() before registering the V4L2 device
[media] uapi/media.h: Use u32 for the number of graph objects
[media] media-entity: don't sleep at media_device_register_entity()
[media] media-entity: increase max number of PADs
[media] media-entity.h: document the remaining functions
[media] media-device.h: use just one u32 counter for object ID
[media] media-entity.h fix documentation for several parameters
[media] DocBook: document media_entity_graph_walk_cleanup()
[media] move documentation to the header files
[media] media: Move MEDIA_ENTITY_MAX_PADS from media-entity.h to media-entity.c
[media] media: Remove pre-allocated entity enumeration bitmap
[media] staging: v4l: davinci_vpbe: Use the new media graph walk interface
[media] staging: v4l: omap4iss: Use the new media graph walk interface
...
While mxl111sf may have multiple frontends, it has just one
tuner. Reflect that on the media graph.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We should not remove the media_device until its last usage,
or we may have use after free troubles.
So, move the per-adapter media_device removal to happen at
the end of the adapter removal code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Several pure digital TV devices have a frontend with the tuner
integrated on it. Add the RF connector when dvb_create_media_graph()
is called on such devices.
Tested with siano and dvb_usb_mxl111sf drivers.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are now two new warnings:
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c: In function 'dvb_usbv2_media_device_register':
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:433:2: warning: ignoring return value of '__media_device_register', declared with attribute warn_unused_result [-Wunused-result]
media_device_register(adap->dvb_adap.mdev);
^
drivers/media/usb/dvb-usb/dvb-usb-dvb.c: In function 'dvb_usb_media_device_register':
drivers/media/usb/dvb-usb/dvb-usb-dvb.c:128:2: warning: ignoring return value of '__media_device_register', declared with attribute warn_unused_result [-Wunused-result]
media_device_register(adap->dvb_adap.mdev);
^
Those are because the drivers are not properly checking if the
media device init and register were succeeded.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The media device node is registered and so made visible to user-space
before entities are registered and links created which means that the
media graph obtained by user-space could be only partially enumerated
if that happens too early before all the graph has been created.
To avoid this race condition, split the media init and registration
in separate functions and only register the media device node when
all the pending subdevices have been registered, either explicitly
by the driver or asynchronously using v4l2_async_register_subdev().
The media_device_register() had a check for drivers not filling dev
and model fields but all drivers in mainline set them and not doing
it will be a driver bug so change the function return to void and
add a BUG_ON() for dev being NULL instead.
Also, add a media_device_cleanup() function that will destroy the
graph_mutex that is initialized in media_device_init().
[mchehab@osg.samsung.com: Fix compilation if !CONFIG_MEDIA_CONTROLLER
and remove two warnings added by this changeset]
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvc_mc_register_entities() function iterated over the entities three
times to initialize the entities, register the subdev for the ones whose
type was UVC_TT_STREAMING and to create the entities links.
But this can be simplied by merging the init and registration logic in a
single loop.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The function uvc_mc_create_pads_links() creates entities links but the
"pads" prefix is redundant since the driver doesn't handle any other
kind of link, so it can be removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the MC next gen rework, what's left for media_entity_init()
is to just initialize the PADs. However, certain devices, like
a FLASH led/light doesn't have any input or output PAD.
So, there's no reason why calling media_entity_init() would be
mandatory. Also, despite its name, what this function actually
does is to initialize the PADs data. So, rename it to
media_entity_pads_init() in order to reflect that.
The media entity actual init happens during entity register,
at media_device_register_entity(). We should move init of
num_links and num_backlinks to it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Entities should have one or more functions. Calling it as a
type proofed to not be correct, as an entity could eventually
have more than one type.
So, rename the field as function.
Please notice that this patch doesn't extend support for
multiple function entities. Such change will happen when
we have real case drivers using it.
No functional changes.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the graph creation fails, don't register the device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the graph creation fails, don't register the device.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If media controller is enabled and mdev is filled, it should
ensure that the media graph will be properly initialized.
Enforce that.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Depending on the input, an au0828 may have a different
number of connectors. add entities to represent them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The DVB core needs to unregister the media device. So, we
can't call au0828_unregister_media_device() before calling
au0828_dvb_unregister(), otherwise the DVB MC free code
(that will be implemented on the next patch) will fail.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tuners actually have at least one connector on its input.
Add a PAD to connect it.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The entire logic that represent graph links were developed on a
time where there were no needs to dynamic remove links. So,
although links are created/removed one by one via some
functions, they're stored as an array inside the entity struct.
As the array may grow, there's a logic inside the code that
checks if the amount of space is not enough to store
the needed links. If it isn't the core uses krealloc()
to change the size of the link, with is bad, as it
leaves the memory fragmented.
So, convert links into a list.
Also, currently, both source and sink entities need the link
at the graph traversal logic inside media_entity. So there's
a logic duplicating all links. That makes it to spend
twice the memory needed. This is not a big deal for today's
usage, where the number of links are not big.
Yet, if during the MC workshop discussions, it was said that
IIO graphs could have up to 4,000 entities. So, we may
want to remove the duplication on some future. The problem
is that it would require a separate linked list to store
the backlinks inside the entity, or to use a more complex
algorithm to do graph backlink traversal, with is something
that the current graph traversal inside the core can't cope
with. So, let's postpone a such change if/when it is actually
needed.
It should also be noticed that the media_link structure uses
44 bytes on 32-bit architectures and 84 bytes on 64-bit
architecture. It will thus be allocated out of the 64-bytes and
96-bytes pools respectively. That's a 12.5% memory waste on
64-bit architectures and 31.25% on 32-bit architecture.
A linked list is less efficient than an array in this case, but
this could later be optimized if we can get rid of the reverse
links (with would reduce memory allocation by 50%).
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The uvc driver creates the pads links before the media entity is
registered with the media device. This doesn't work now that obj
IDs are used to create links so the media_device has to be set.
Move entities registration logic before pads links creation.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With the new API, a link can be either between two PADs or between an interface
and an entity. So, we need to use a better name for the function that create
links between two pads.
So, rename the such function to media_create_pad_link().
No functional changes.
This patch was created via this shell script:
for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f) $(find include/ -name '*.h' -type f) ; do sed s,media_entity_create_link,media_create_pad_link,g <$i >a && mv a $i; done
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This logic was broken on the original patch, likely due to a
cut-and-paste mistake.
Fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Currently, media_entity_init() creates an array with the links,
allocated at init time. It provides a parameter (extra_links)
that would allocate more links than the current needs, but this
is not used by any driver.
As we want to be able to do dynamic link allocation/removal,
we'll need to change the implementation of the links. So,
before doing that, let's first remove that extra unused
parameter, in order to cleanup the interface first.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of seeking for the decoder every time analog stream is
started, cache it. This simplifies the code a little bit.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for analog and dvb tv using media controller.
Signed-off-by: Rafael Lourenço de Lima Chehab <chehabrafael@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* patchwork: (204 commits)
[media] rc: sunxi-cir: Initialize the spinlock properly
[media] rtl2832: do not filter out slave TS null packets
[media] rtl2832: print reg number on error case
[media] rtl28xxu: return demod reg page from driver cache
[media] coda: enable MPEG-2 ES decoding
[media] coda: don't start streaming without queued buffers
[media] coda: hook up vidioc_prepare_buf
[media] coda: relax coda_jpeg_check_buffer for trailing bytes
[media] coda: make to_coda_video_device static
[media] s5p-mfc: remove volatile attribute from MFC register addresses
[media] s5p-mfc: merge together s5p_mfc_hw_call and s5p_mfc_hw_call_void
[media] s5p-mfc: use spinlock to protect MFC context
[media] s5p-mfc: remove unnecessary callbacks
[media] s5p-mfc: make queue cleanup code common
[media] s5p-mfc: use one implementation of s5p_mfc_get_new_ctx
[media] s5p-mfc: constify s5p_mfc_codec_ops structures
[media] au8522: Avoid memory leak for device config data
[media] ir-lirc-codec.c: don't leak lirc->drv-rbuf
[media] uvcvideo: small cleanup in uvc_video_clock_update()
[media] uvcvideo: Fix reading the current exposure value of UVC
...
Return current active rtl2830/rtl2832 register page from the driver
cache in order to reduce I2C I/O. Register page is already cached
due to I2C write needs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Driver requested device firmware version string during probe using
only 24 byte long buffer. That buffer is too small for newer firmware
versions, which causes device firmware hang - device stops responding
to any commands after that. Increase buffer size to 128 which should
be enough for any current and future version strings.
Link: https://github.com/airspy/host/issues/27
Cc: <stable@vger.kernel.org> # 3.17+
Reported-by: Benjamin Vernoux <bvernoux@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Used Avago MGA-81563 RF amplifier could be destroyed pretty easily
with too strong signal or transmitting to bad antenna.
Add module parameter 'enable_rf_gain_ctrl' which allows enabling
RF gain control - otherwise, default without the module parameter,
RF gain control is set to 'grabbed' state which prevents setting
value to the control.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/usb/hackrf/hackrf.c:1533 hackrf_probe()
error: we previously assumed 'dev' could be null (see line 1366)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Smatch is not smart enough to see that "&stream->clock.lock" and
"&clock->lock" are the same thing so it complains about the locking
here. Let's make it more consistent.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
V4L2_CID_EXPOSURE_ABSOLUTE property does not return an updated value when
autoexposure (V4L2_CID_EXPOSURE_AUTO) is turned on. This patch fixes this
issue by adding the UVC_CTRL_FLAG_AUTO_UPDATE flag.
Tested on a C920 camera.
Signed-off-by: Anton V. Shokurov <shokurov.anton.v@yandex.ru>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Move timestamp from struct vb2_v4l2_buffer to struct vb2_buffer
for common use, and change its type to u64 in order to handling
y2038 problem. This patch also includes all device drivers' changes related to
this restructuring.
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The queue_setup callback has a void pointer that is just for V4L2
and is the pointer to the v4l2_format struct that was passed to
VIDIOC_CREATE_BUFS. The idea was that drivers would use the information
from that struct to buffers suitable for the requested format.
After the vb2 split series this pointer is now a void pointer,
which is ugly, and the reality is that all existing drivers will
effectively just look at the sizeimage field of v4l2_format.
To make this more generic the queue_setup callback is changed:
the void pointer is dropped, instead if the *num_planes argument
is 0, then use the current format size, if it is non-zero, then
it contains the number of requested planes and the sizes array
contains the requested sizes. If either is unsupported, then return
-EINVAL, otherwise use the requested size(s).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The pixelaspect ratio was set incorrectly for 60Hz formats.
And since cropcap wasn't implemented at all for the -417 (compressed
video) the pixelaspect was unknown for compressed video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 120c41d347.
The patch doesn't add the corresponding documentation bits to the
media infrastructure uAPI DocBook. Also, they're for 3D formats,
with requre further discussions.
Requested-by: Hans Verkuil <hverkuil@xs4all.nl>
Requested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
While https was always supported on linuxtv.org, only in
Dec 3 2015 the website is using valid certificates.
As we're planning to drop pure http support on some
future, change all references at the media subsystem
to point to the https URL instead.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for Intel DS4 depth camera in uvc driver.
This includes adding new uvc GUIDs for the new pixel formats,
adding new V4L pixel format definition to user api headers,
and updating the uvc driver GUID-to-4cc tables with the new formats.
Change-Id: If240d95a7d4edc8dcc3e02d58cd8267a6bbf6fcb
Tested-by: Greenberg, Aviv D <aviv.d.greenberg@intel.com>
Signed-off-by: Aviv Greenberg <aviv.d.greenberg@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The cx2341x_handler_ops structures are never modified, so declare them as
const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the new match_reduced_fps argument to v4l2_match_dv_timings().
Depending on the situation you may or may not desire to match the
reduced_fps flag. Typically only HDMI transmitters will need to
check for this flag.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The usbvision driver crashes when a specially crafted usb device with invalid
number of interfaces or endpoints is detected. This fix adds checks that the
device has proper configuration expected by the driver.
Reported-by: Ralf Spenneberg <ralf@spenneberg.net>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for the DVB-T/C/T2 usb stick WinTV-soloHD from
Hauppauge. It adds the usb ID 2040:0264 Hauppauge to the cards of the
driver em28xx.
I successfully tested DVB-T/C and the IR remote control with the
firmware dvb-demod-si2168-b40-01.fw.
Signed-off-by: Arno Bauernoeppel <arno@aziraphale.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The ttusbdecfe_config structure is never modified, so declare it
as const.
Other references to this structure type were already declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The mxl111sf_demod_config structure is never modified, so declare it
as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
UVC 1.5 devices report a bInterfaceProtocol value set to 1 in their
interface descriptors. The uvcvideo driver only matches on
bInterfaceProtocol 0, preventing those devices from being detected.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Microsoft Surface Pro 3 cameras have been
reported to work out of the box with the driver with an updated match
table.
Enable UVC 1.5 support in the match table to support the devices that
can work with the current driver implementation. Devices that can't will
fail, but that's hardly a regression as they're currently not detected
at all anyway.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Terratec Cinergy T XS is a DVB-T receiver with no analog TV tuner.
This patch adds support for the cards carrying the mt2060 tuner; it's
unclear whether there are cards sold under the same name which use a
different tuner.
As long as there are no reports of such cards, and indeed as long as
there are no working drivers for them, we assume that the USB device
[0ccd:0043] is carrying the mt2060 tuner.
Signed-off-by: Alberto Mardegan <mardy@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case the request to locate the firmware file part 2 fails, the error
path releases the already freed firmware memory location again. Thus
reset the firmware pointer to NULL after releasing firmware file part 1.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Return values of mxl111sf_enable_usb_output and mxl1x1sf_top_master_ctrl
are not validated.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make all v4l2-clk's clock name use V4L2_CLK_NAME_SIZE definition.
In future, if the string is increased we just need to change the
V4L2_CLK_NAME_SIZE once.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the crash reported in:
http://seclists.org/bugtraq/2015/Oct/35
The interface number needs a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Vladis Dronov <vdronov@redhat.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Wolfram Sang