Armada 8040 also needs orion pinctrl, and as these symbols are only
selected, there's no need to make them depend on PLAT_ORION.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset property of the pinctrl node, when a regmap is used in the
device tree, was never used nor documented in the binding. Moreover, the
compatible string is enough to let the driver know which offset using.
So this patch removes the property and move the information at the driver
level.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add Tsin A pins to bank DV and X.
We don't have a driver for the tsin yet but since the tsin A pinmux is
enabled by default at boot time, declaring this pinmux is required to
properly operate on GPIOX.
Without this change, GPIOX 8, 9, 10 and 11 can't be driven as GPIO output
as the tsin A seems to have priority.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl/GPIO support for Intel Cannon Lake PCH. The Cannon
Lake PCH GPIO is based on newer version of the Intel GPIO hardware.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some SoCs not all pins in a group use the same mode when a certain
function is muxed out of them. This makes it possible to specify mode per
pin as an array instead in addition to single integer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel GPIO hardware has a concept of pad groups, which means 1 to 32
pads occupying their own GPI_IS, GPI_IE, PAD_OWN and so on registers. The
existing hardware has the same amount of pads in each pad group (except the
last one) so it is possible to use community->gpp_size to calculate start
offset of each register.
With the next generation SoCs the pad group size is not always the same
anymore which means we cannot use community->gpp_size for register offset
calculations directly.
To support variable size pad groups we introduce struct intel_padgroup that
can be filled in by the client drivers according the hardware pad group
layout. The core driver will always use these when it performs calculations
for pad register offsets. The core driver will automatically populate pad
groups based on community->gpp_size if the driver does not provide any.
This makes sure the existing drivers still work as expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R_PIO on the A83T is almost the same as the one found on the A64,
except that the CIR_RX function was moved from pin PL11 to pin PL12.
Add a driver for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R_PIO on the A83T is almost the same as the one found on the A64,
except that the CIR_RX function was moved from pin PL11 to pin PL12.
Add a compatible string for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use consistent license headers for Broadcom files by
placing additional comments outside of standard legal header.
Also, update legal header to 2017 format as "Broadcom Corporation"
has changed to "Broadcom".
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct irq_domain_ops is not modified, so it can be made const.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no link between the number of elements of tab which contains all
pin desc (located in each pinctrl-stm32xxxx.c files) and the pin number
(defined in the tab).
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO interrupt information to pinctrl data. Added to the original
version from Jerome was data for Meson GXL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 34e61801a3 "pinctrl: meson-gxbb: Add missing GPIODV_18
pin entry" I started to get the following warning:
"meson-pinctrl c8834000.periphs:pinctrl@4b0: names 119 do not match
number of GPIOs 120"
It turned out that not the mentioned commit has a problem, it just
revealed another problem which had existed before.
There is no PIN GPIOX_22 on Meson GXBB.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add PWM, AVB MDIO/MII, and sound pin groups on R-Car M3-W,
- Add support for RZ/G1M and RZ/G1E,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JT2m
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.13
- Add PWM, AVB MDIO/MII, and sound pin groups on R-Car M3-W,
- Add support for RZ/G1M and RZ/G1E,
- Small fixes and cleanups.
This patch ensures that pin is correctly set as gpio input when it is used
as an interrupt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With "SPI_MASTER=y && I2C=m", we can build mcp23s08 as a built-in driver,
which then results in a link failure:
drivers/pinctrl/built-in.o: In function `mcp23s08_probe_one.isra.0':
:(.text+0x7910): undefined reference to `__devm_regmap_init_i2c'
drivers/pinctrl/built-in.o: In function `mcp23s08_init':
:(.init.text+0x110): undefined reference to `i2c_register_driver'
drivers/pinctrl/built-in.o: In function `mcp23s08_exit':
:(.exit.text+0x3c): undefined reference to `i2c_del_driver'
To avoid the problem, this adds another dependency on I2C that enforces
mcp23s08 to be a loadable module whenever the I2C core is a module.
Fixes: 64ac43e6fa ("gpio: mcp23s08: move to pinctrl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner R40 has a pin controller like the ones in older Allwinner SoCs
(especially A20), and can use modified version of the A10/A20 pinctrl
driver.
Add a compatible string for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we added A20 support to A10 pinctrl driver, now we can delete the
dedicated A20 pinctrl driver, which is duplicated code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[Drop Makefile entry]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As A20 is designed as a pin-compatible upgrade of A10, their pin
controller are very similar, and can share one driver.
Add A20 support to the A10 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner A10, A20 and R40 SoCs have similar GPIO layout.
Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support
into A10 driver, and add R40 support into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 2 IP blocks pin routes need to be switched, that are
uart2dbg, pcie_clkreq.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 8 IP blocks pin routes need to be switched, that are
uart2dbg, gmac-m1-optimized, pdm, spi, i2s2, card, tsp, cif.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 9 IP blocks pin routes need to be switched, that are
pwm-0, pwm-1, pwm-2, pwm-3, sdio, spi, emmc, uart2, uart1.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the some rockchip SOCS, some things like rk3399 specific uart2 can use
multiple pins. Somewhere between the pin io-cells and the uart it seems
to have some sort of switch to decide to which pin to actually route the
data.
+-------+ +--------+ /- GPIO4_B0 (pinmux 2)
| uart2 | -- | switch | --- GPIO4_C0 (pinmux 2)
+-------+ +--------+ \- GPIO4_C3 (pinmux 2)
(switch selects one of the 3 pins base on the GRF_SOC_CON7[BIT0, BIT1])
The routing switch is determined by one pin of a specific group to be set
to its special pinmux function. If the pinmux setting is wrong for that
pin the ip block won't work correctly anyway.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix compile errors due to missing OF.
Cc: Paul Cercueil <paul@crapouillou.net>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs enables
the Link and Activity LEDs signals.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO SPDIF pins were incorrectly defined with the EE pin offset.
Fixes: b840d649f9 ("pinctrl: meson: gxl: add spdif output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO I2S pins were incorrectly defined with the EE pin offset.
Fixes: 2899adf042 ("pinctrl: meson: gxl: add i2s output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIODV_18 entry was missing in the original driver push.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixups here tend to be more of a conglomerate of some of the other
repeated/systematic ones we've seen in the earlier pinctrl cleanups.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h
One driver has a .remove that would be dispatched on module_exit,
and as that code is essentially orphaned, so we remove it. In case
anyone was previously doing the (pointless) unbind to get to that
function, we disable unbind for this one driver as well.
A couple bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Eric Anholt <eric@anholt.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Sherman Yin <syin@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get similar changes, so they are handled in batch.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h.
A couple drivers have module_exit() code that is essentially orphaned,
and so we remove that.
Quite a few bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Pritesh Raithatha <praithatha@nvidia.com>
Cc: Ashwini Ghuge <aghuge@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_device_get_match_data() instead of of_match_device().
It allows us to remove the forward declaration of pcs_of_match.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a couple of issues with group_desc initialization in function
zx_pinctrl_build_state().
- num_pins is not initialized and remains zero.
- pins shouldn't be initialized with a pointer to variable in the
stack.
With them fixed, pin_request() in pinmux_enable_setting() can be invoked
correctly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXBB pinctrl driver
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXL pinctrl driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There was no entry for the mvebu pinctrl drivers. As they are tightly
linked to the SoCs and there is a lot of common code to support the
various pinctrl of each SoCs, then add a new entry for the mvebu
maintainers.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Each text file under Documentation follows a different
format. Some doesn't even have titles!
Change its representation to follow the adopted standard,
using ReST markups for it to be parseable by Sphinx.
This document is almost following the standard stile.
There are only two things to adjust on it:
- promote the level of the document title;
- mark literal blocks as such.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
[Fix some indentations]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The comment does not match the driver, which actually supports
automatic assignment. Fix this by updating the comment.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver supports using mcp23xxx as interrupt controller, so
let's drop all comments stating otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves irq property handling from spi/i2c specific code into
the generic mcp23s08_probe_one. This is possible because the
device properties are named equally.
As a side-effect this drops support for setting the properties via
pdata, which has no mainline users. If boardcode wants to enable
the chip as interrupt controller it can attach the device properties
instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify spi pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify i2c pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Russell King