Reported by Mikulas Patocka.
VIA VT82C586B + Transcend TS64GSSD25-M v0826 does not work in UDMA mode
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata-sff, ata_sff_post_internal_cmd() directly calls ata_bmdma_stop()
instead of ap->ops->bmdma_stop(). This can be a problem for controllers
that use their own bmdma_stop for which the generic sff one isn't suitable
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add support for the ATA TRIM command in libata. We translate a WRITE SAME 16
command with the unmap bit set into an ATA TRIM command and export enough
information in READ CAPACITY 16 and the block limits EVPD page so that the new
SCSI layer discard support will driver this for us.
Note that I hardcode the WRITE_SAME_16 opcode for now as the patch to introduce
the symbolic is not in 2.6.32 yet but only in the SCSI tree - as soon as it is
merged we can fix it up to properly use the symbolic name.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If ATA device failed FLUSH, it means that the device failed to write
out some amount of data and the error needs to be reported to upper
layers. As retries can't recover the lost data, FLUSH failures need to
be reported immediately in general.
However, if FLUSH fails due to transmission errors, the FLUSH needs to
be retried; otherwise, filesystems may switch to RO mode and/or raid
array may drop a drive for a random transmission glitch.
This condition can be rather easily reproduced on certain ahci
controllers which go through a PHY event after powersave mode switch +
ext4 combination. Powersave mode switch is often closely followed by
flush from the filesystem failing the FLUSH with ATA bus error which
makes the filesystem code believe that data is lost and drop to RO
mode. This was reported in the following bugzilla bug.
http://bugzilla.kernel.org/show_bug.cgi?id=14543
This patch makes libata EH retry FLUSH if it wasn't failed by the
device.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Andrey Vihrov <andrey.vihrov@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Enable device hot-plug support on Port multiplier fan-out ports
Signed-off-by: Ashish Kalra <Ashish.Kalra@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Alan Cox reported that cable detection sometimes works unreliably
for HPT3xxN and that the issue is fixed by adding debounce delay
as used by the vendor driver.
Sergei Shtylyov also noticed that debounce delay is needed for all
HPT37x and HPT3xxN chipsets according to vendor drivers.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The detection was reversed between primary and secondary ports.
Fix it to match hpt366 and the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sysfs attributes shouldn't require newlines. Make it possible to set the
link power management policy without a trailing newline.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We can use the same ->pre_reset method for all HPT37x chipsets now.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
I obseved there is a sata_async_notification() for every ahci
interrupt. But the async notification does nothing (this is hard
disk drive and no pmp). This cause cpu wastes some time on sntf
register access.
It appears ICH AHCI doesn't support SNotification register, but the
controller reports it does. After quirking it, the async notification
disappears.
PS. it appears all ICH don't support SNotification register from ICH
manual, don't know if we need quirk all ICH. I don't have machines
with all kinds of ICH.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The following patch adds MSI support. Some platforms
may have broken MSI, so those are defaulted to use
legacy PCI interrupts.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Remove the experimental tag on Parallel ATA drivers. Though some of the
individual PATA drivers are still marked as experimental, as a group they can
hardly be considered to be, given they've been used in various distros for some
time.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In via_init_one, when via_isa_bridges iterator reaches
PCI_DEVICE_ID_VIA_ANON and last but one via_isa_bridges bridge is
found but rev doesn't match, pci_dev_put(isa) is called twice.
Do pci_dev_put only once.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Missing _SDD is not an error. Don't treat it as one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
update_transition_efer() masks out some efer bits when deciding whether
to switch the msr during guest entry; for example, NX is emulated using the
mmu so we don't need to disable it, and LMA/LME are handled by the hardware.
However, with shared msrs, the comparison is made against a stale value;
at the time of the guest switch we may be running with another guest's efer.
Fix by deferring the mask/compare to the actual point of guest entry.
Noted by Marcelo.
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch corrects the checking of the new address for the prefix register.
On s390, the prefix register is used to address the cpu's lowcore (address
0...8k). This check is supposed to verify that the memory is readable and
present.
copy_from_guest is a helper function, that can be used to read from guest
memory. It applies prefixing, adds the start address of the guest memory in
user, and then calls copy_from_user. Previous code was obviously broken for
two reasons:
- prefixing should not be applied here. The current prefix register is
going to be updated soon, and the address we're looking for will be
0..8k after we've updated the register
- we're adding the guest origin (gmsor) twice: once in subject code
and once in copy_from_guest
With kuli, we did not hit this problem because (a) we were lucky with
previous prefix register content, and (b) our guest memory was mmaped
very low into user address space.
Cc: stable@kernel.org
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
This way, we don't leave a dangling notifier on cpu hotunplug or module
unload. In particular, module unload leaves the notifier pointing into
freed memory.
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Otherwise would cause VMEntry failure when using ept=0 on unrestricted guest
supported processors.
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
While we are never normally passed an instruction that exceeds 15 bytes,
smp games can cause us to attempt to interpret one, which will cause
large latencies in non-preempt hosts.
Cc: stable@kernel.org
Signed-off-by: Avi Kivity <avi@redhat.com>
This patch moves s390 processor status word into the base kvm_run
struct and keeps it up-to date on all userspace exits.
The userspace ABI is broken by this, however there are no applications
in the wild using this. A capability check is provided so users can
verify the updated API exists.
Cc: stable@kernel.org
Signed-off-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This new IOCTL exports all yet user-invisible states related to
exceptions, interrupts, and NMIs. Together with appropriate user space
changes, this fixes sporadic problems of vmsave/restore, live migration
and system reset.
[avi: future-proof abi by adding a flags field]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
These happen when we trap an exception when another exception is being
delivered; we only expect these with MCEs and page faults. If something
unexpected happens, things probably went south and we're better off reporting
an internal error and freezing.
Signed-off-by: Avi Kivity <avi@redhat.com>
Usually userspace will freeze the guest so we can inspect it, but some
internal state is not available. Add extra data to internal error
reporting so we can expose it to the debugger. Extra data is specific
to the suberror.
Signed-off-by: Avi Kivity <avi@redhat.com>
Obviously, people tend to extend this header at the bottom - more or
less blindly. Ensure that deprecated stuff gets its own corner again by
moving things to the top. Also add some comments and reindent IOCTLs to
make them more readable and reduce the risk of number collisions.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Decouple KVM_GUESTDBG_INJECT_DB and KVM_GUESTDBG_INJECT_BP from
KVM_GUESTDBG_ENABLE, their are actually orthogonal. At this chance,
avoid triggering the WARN_ON in kvm_queue_exception if there is already
an exception pending and reject such invalid requests.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Otherwise kvm will leak memory on multiple KVM_CREATE_IRQCHIP.
Also serialize multiple accesses with kvm->lock.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Large page translations are always synchronized (either in level 3
or level 2), so its not necessary to properly deal with them
in the invlpg handler.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
GUEST_CR3 is updated via kvm_set_cr3 whenever CR3 is modified from
outside guest context. Similarly pdptrs are updated via load_pdptrs.
Let kvm_set_cr3 perform the update, removing it from the vcpu_run
fast path.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Acked-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The old BUILD_BUG_ON implementation didn't work with __builtin_constant_p().
Fixing that revealed this test had been inverted for a long time without
anybody noticing...
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Instead of reloading syscall MSRs on every preemption, use the new shared
msr infrastructure to reload them at the last possible minute (just before
exit to userspace).
Improves vcpu/idle/vcpu switches by about 2000 cycles (when EFER needs to be
reloaded as well).
[jan: fix slot index missing indirection]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The various syscall-related MSRs are fairly expensive to switch. Currently
we switch them on every vcpu preemption, which is far too often:
- if we're switching to a kernel thread (idle task, threaded interrupt,
kernel-mode virtio server (vhost-net), for example) and back, then
there's no need to switch those MSRs since kernel threasd won't
be exiting to userspace.
- if we're switching to another guest running an identical OS, most likely
those MSRs will have the same value, so there's little point in reloading
them.
- if we're running the same OS on the guest and host, the MSRs will have
identical values and reloading is unnecessary.
This patch uses the new user return notifiers to implement last-minute
switching, and checks the msr values to avoid unnecessary reloading.
Signed-off-by: Avi Kivity <avi@redhat.com>
Currently MSR_KERNEL_GS_BASE is saved and restored as part of the
guest/host msr reloading. Since we wish to lazy-restore all the other
msrs, save and reload MSR_KERNEL_GS_BASE explicitly instead of using
the common code.
Signed-off-by: Avi Kivity <avi@redhat.com>
The svm_set_cr0() call will initialize save->cr0 properly even when npt is
enabled, clearing the NW and CD bits as expected, so we don't need to
initialize it manually for npt_enabled anymore.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
svm_vcpu_reset() was not properly resetting the contents of the guest-visible
cr0 register, causing the following issue:
https://bugzilla.redhat.com/show_bug.cgi?id=525699
Without resetting cr0 properly, the vcpu was running the SIPI bootstrap routine
with paging enabled, making the vcpu get a pagefault exception while trying to
run it.
Instead of setting vmcb->save.cr0 directly, the new code just resets
kvm->arch.cr0 and calls kvm_set_cr0(). The bits that were set/cleared on
vmcb->save.cr0 (PG, WP, !CD, !NW) will be set properly by svm_set_cr0().
kvm_set_cr0() is used instead of calling svm_set_cr0() directly to make sure
kvm_mmu_reset_context() is called to reset the mmu to nonpaging mode.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This should have no effect, it is just to make the code clearer.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
With big endian userspace, we can't quite figure out if a pointer
is 32 bit (shifted >> 32) or 64 bit when we read a 64 bit pointer.
This is what happens with dirty logging. To get the pointer interpreted
correctly, we thus need Arnd's patch to implement a compat layer for
the ioctl:
A better way to do this is to add a separate compat_ioctl() method that
converts this for you.
Based on initial patch from Arnd Bergmann.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
When we migrate a kvm guest that uses pvclock between two hosts, we may
suffer a large skew. This is because there can be significant differences
between the monotonic clock of the hosts involved. When a new host with
a much larger monotonic time starts running the guest, the view of time
will be significantly impacted.
Situation is much worse when we do the opposite, and migrate to a host with
a smaller monotonic clock.
This proposed ioctl will allow userspace to inform us what is the monotonic
clock value in the source host, so we can keep the time skew short, and
more importantly, never goes backwards. Userspace may also need to trigger
the current data, since from the first migration onwards, it won't be
reflected by a simple call to clock_gettime() anymore.
[marcelo: future-proof abi with a flags field]
[jan: fix KVM_GET_CLOCK by clearing flags field instead of checking it]
Signed-off-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Commit 705c5323 opened the doors of hell by unconditionally injecting
single-step flags as long as guest_debug signaled this. This doesn't
work when the guest branches into some interrupt or exception handler
and triggers a vmexit with flag reloading.
Fix it by saving cs:rip when user space requests single-stepping and
restricting the trace flag injection to this guest code position.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Support for Xen PV-on-HVM guests can be implemented almost entirely in
userspace, except for handling one annoying MSR that maps a Xen
hypercall blob into guest address space.
A generic mechanism to delegate MSR writes to userspace seems overkill
and risks encouraging similar MSR abuse in the future. Thus this patch
adds special support for the Xen HVM MSR.
I implemented a new ioctl, KVM_XEN_HVM_CONFIG, that lets userspace tell
KVM which MSR the guest will write to, as well as the starting address
and size of the hypercall blobs (one each for 32-bit and 64-bit) that
userspace has loaded from files. When the guest writes to the MSR, KVM
copies one page of the blob from userspace to the guest.
I've tested this patch with a hacked-up version of Gerd's userspace
code, booting a number of guests (CentOS 5.3 i386 and x86_64, and
FreeBSD 8.0-RC1 amd64) and exercising PV network and block devices.
[jan: fix i386 build warning]
[avi: future proof abi with a flags field]
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
This (broken) check dates back to the days when this code was shared
across architectures. x86 has IOMEM, so drop it.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>