Commit 9131f3de2 ("ipv6: Do not iterate over all interfaces when
finding source address on specific interface.") did not properly
update best source address available. Plus, it introduced
possible NULL pointer dereference.
Bug was reported by Erik Kline <ek@google.com>.
Based on patch proposed by Hajime Tazaki <thehajime@gmail.com>.
Fixes: 9131f3de24 ("ipv6: Do not
iterate over all interfaces when finding source address
on specific interface.")
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Hajime Tazaki <thehajime@gmail.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The member (u32) "num_active_agg" of struct qfq_sched has been unused
since its introduction in 462dbc9101
"pkt_sched: QFQ Plus: fair-queueing service at DRR cost" and (AFAICT)
there is no active plan to use it; this removes the member.
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
Minor conflict in br_mdb.c, in 'net' we added a memset of the
on-stack 'ip' variable whereas in 'net-next' we assign a new
member 'vid'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now all user mdb entries were added in vlan 0, this patch adds
support to allow the user to specify the vlan for the entry.
About the uapi change a hole in struct br_mdb_entry is used so the size
and offsets are kept the same (verified with pahole and tested with older
iproute2).
Example:
$ bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent vlan 2000
dev br0 port eth1 grp 239.0.0.1 permanent vlan 200
dev br0 port eth1 grp 239.0.0.1 permanent
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the default to build IPv6 into the kernel. IPv6
now has significant traction and any remaining vestiges of IPv6
not being provided parity with IPv4 should be swept away. IPv6 is now
core to the Internet and kernel.
Points on IPv6 adoption:
- Per Google statistics, IPv6 usage has reached 7% on the Internet
and continues to exhibit an exponential growth rate
https://www.google.com/intl/en/ipv6/statistics.html
- Just a few days ago ARIN officially depleted its IPv4 pool
- IPv6 only data centers are being successfully built
(e.g. at Facebook)
This patch changes the IPv6 Kconfig for IPV6. Default for CONFIG_IPV6
is set to "y" and the text has been updated to reflect the maturity of
IPv6.
Impact:
Under some circumstances building modules in to kernel might have a
performance advantage. In my testing, I did notice a very slight
improvement.
This will obviously increase the size of the kernel image. In my
configuration I see:
IPv6 as module:
text data bss dec hex filename
9703666 1899288 933888 12536842 bf4c0a vmlinux
IPv6 built into kernel
text data bss dec hex filename
9436490 1879600 913408 12229498 ba9b7a vmlinux
Which increases text size by ~270K (2.8% increase in size for me). If
image size is an issue, presumably for a device which does not do IP
networking (IMO we should be discouraging IPv4-only devices), IPV6 can
be disabled or still built as a module.
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJVorxbAAoJEP5prqPJtc/H5zgH/2nvkmT3aQ1gBKdU8L+Ten5D
LIKYyDJ67agNoMfEC/5xWOm7P3X8Qi8cGc326/9AZE22QLE5x6fMCq/SmEC4MA25
GKu2ocwosdPVhIDQOY33IYZHxxtV8UZjt5KdNbQnNO6+iqE6tX5CbgueMlcWusry
WmPCOlezTqHydXo0TYYLPjmqJ66RlrQMWYKvcB0SaxLYQfkBGbkW+fei3wdE4kW1
t7cocRj6Ievv59wCeF+G+fpviTVQVR5bknGA0J3lku9onATOYfdArEAD9FRajygG
KhA/eNr0YEA40VO/baUInuEAJ/YvDqdk9LoyJ1DOXgUv1ysxYSxu/44G/IcZsOU=
=+zVD
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.2-20150712' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2015-07-12
this is a pull request of 8 patchs for net/master.
Sergei Shtylyov contributes 5 patches for the rcar_can driver, fixing the IRQ
check and several info and error messages. There are two patches by J.D.
Schroeder and Roger Quadros for the c_can driver and dra7x-evm device tree,
which precent a glitch in the DCAN1 pinmux. Oliver Hartkopp provides a better
approach to make the CAN skbs unique, the timestamp is replaced by a counter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 514ac99c64 "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.
Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245eb "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.
This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.
This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.
Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.
Fixes: 5e95329b70 ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.
Fixes: 5e95329b701c: ("dsa: add device tree bindings to register DSA switches")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to abort attribute setting or object addition, if the
prepare phase returned operation not supported.
Thus, abort these two transactions only if the error is not -EOPNOTSUPP.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3cc4949269.
There is nothing wrong with coalescing during defragmentation, it
reduces truesize overhead and simplifies things for the receiving
socket (no fraglist walk needed).
However, it also destroys geometry of the original fragments.
While that doesn't cause any breakage (we make sure to not exceed largest
original size) ip_do_fragment contains a 'fastpath' that takes advantage
of a present frag list and results in fragments that (in most cases)
match what was received.
In case its needed the coalescing could be done later, when we're sure
the skb is not forwarded. But discussion during NFWS resulted in
'lets just remove this for now'.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reconsidering my commit 20462155 "net: inet_diag: export IPV6_V6ONLY
sockopt", I am not happy with the limitations it causes for socket
analysing code in userspace. Exporting the value only if it is set makes
it hard for userspace to decide whether the option is not set or the
kernel does not support exporting the option at all.
>From an auditor's perspective, the interesting question for listening
AF_INET6 sockets is: "Does it NOT have IPV6_V6ONLY set?" Because it is
the unexpected case. This patch allows to answer this question reliably.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If outgoing interface is specified and the candidate address is
restricted to the outgoing interface, it is enough to iterate
over that given interface only.
Signed-off-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Acked-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now when a querier was present static entries couldn't be deleted.
Fix this and allow the user to manipulate the mdb with or without a
querier.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:
CPU 1 CPU 2
skb->dev: no reference
process_backlog:__skb_dequeue
process_backlog:local_irq_enable
on_each_cpu for
flush_backlog => IPI(hardirq): flush_backlog
- packet not found in backlog
CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections
netdev_run_todo,
rcu_barrier: no
ongoing callbacks
__netif_receive_skb_core:rcu_read_lock
- too late
free dev
process packet for freed dev
Fixes: 6e583ce524 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 381c759d99 ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.
Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.
Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Fixes: 6e583ce524 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c29390c6df ("xps: must clear sender_cpu before forwarding")
fixed an issue in normal forward path, caused by sender_cpu & napi_id
skb fields being an union.
Bridge is another point where skb can be forwarded, so we need
the same cure.
Bug triggers if packet was received on a NIC using skb_mark_napi_id()
Fixes: 2bd82484bb ("xps: fix xps for stacked devices")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Bob Liu <bob.liu@oracle.com>
Tested-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 900f65d361 ("tcp: move duplicate code from
tcp_v4_init_sock()/tcp_v6_init_sock()"), we no longer
need to export tcp_init_xmit_timers()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill also the port group state when sending notifications.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
flags local variable in __mkroute_input is not used as a variable.
Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to allow non-local binds similar to how this was done for IPv4.
Non-local binds are very useful in emulating the Internet in a box, etc.
This add the ip_nonlocal_bind sysctl under ipv6.
Testing:
Set up nonlocal binding and receive routing on a host, e.g.:
ip -6 rule add from ::/0 iif eth0 lookup 200
ip -6 route add local 2001:0:0:1::/64 dev lo proto kernel scope host table 200
sysctl -w net.ipv6.ip_nonlocal_bind=1
Set up routing to 2001:0:0:1::/64 on peer to go to first host
ping6 -I 2001:0:0:1::1 peer-address -- to verify
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_twsk_deschedule() calls are followed by inet_twsk_put().
Only particular case is in inet_twsk_purge() but there is no point
to defer the inet_twsk_put() after re-enabling BH.
Lets rename inet_twsk_deschedule() to inet_twsk_deschedule_put()
and move the inet_twsk_put() inside.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timewait sockets have a complex refcounting logic.
Once we realize it should be similar to established and
syn_recv sockets, we can use sk_nulls_del_node_init_rcu()
and remove inet_twsk_unhash()
In particular, deferred inet_twsk_put() added in commit
13475a30b6 ("tcp: connect() race with timewait reuse")
looks unecessary : When removing a timewait socket from
ehash or bhash, caller must own a reference on the socket
anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen_thread_worker() doesn't need to wait for kthread_stop(), it
can simply exit. Just pktgen_create_thread() and pg_net_exit() should
do get_task_struct()/put_task_struct(). kthread_stop(dead_thread) is
fine.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pktgen_thread_worker() is obviously racy, kthread_stop() can come
between the kthread_should_stop() check and set_current_state().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Marcelo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The congestion state and cwnd can be updated in the wrong order.
For example, upon receiving a dubious ACK, we incorrectly raise
the cwnd first (tcp_may_raise_cwnd()/tcp_cong_avoid()) because
the state is still Open, then enter recovery state to reduce cwnd.
For another example, if the ACK indicates spurious timeout or
retransmits, we first revert the cwnd reduction and congestion
state back to Open state. But we don't raise the cwnd even though
the ACK does not indicate any congestion.
To fix this problem we should first call tcp_fastretrans_alert() to
process the dubious ACK and update the congestion state, then call
tcp_may_raise_cwnd() that raises cwnd based on the current state.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original design slow start is only used to raise cwnd
when cwnd is stricly below ssthresh. It makes little sense
to slow start when cwnd == ssthresh: especially
when hystart has set ssthresh in the initial ramp, or after
recovery when cwnd resets to ssthresh. Not doing so will
also help reduce the buffer bloat slightly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper to test the slow start condition in various congestion
control modules and other places. This is to prepare a slight improvement
in policy as to exactly when to slow start.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that the call skb_defer_rx_timestamp will first
check for a phydev before going in and manipulating the skb->data and
skb->len values. By doing this we can avoid unnecessary work on network
devices that don't support phydev. As a result we reduce the total
instruction count needed to process this on most devices.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
V1 of this patch contains Eric Dumazet's suggestion to move the per
dst RTAX_QUICKACK check into tcp_in_quickack_mode(). Thanks Eric.
I ran some tests and after setting the "ip route change quickack 1"
knob there were still many delayed ACKs sent. This occured
because when icsk_ack.quick=0 the !icsk_ack.pingpong value is
subsequently ignored as tcp_in_quickack_mode() checks both these
values. The condition for a quick ack to trigger requires
that both icsk_ack.quick != 0 and icsk_ack.pingpong=0. Currently
only icsk_ack.pingpong is controlled by the knob. But the
icsk_ack.quick value changes dynamically depending on heuristics.
The crux of the matter is that delayed acks still cannot be entirely
disabled even with the RTAX_QUICKACK per dst knob enabled. This
patch ensures that a quick ack is always sent when the RTAX_QUICKACK
per dst knob is turned on.
The "ip route change quickack 1" knob was recently added to enable
quickacks. It was modeled around the TCP_QUICKACK setsockopt() option.
This issue is that even with "ip route change quickack 1" enabled
we still see delayed ACKs under some conditions. It would be nice
to be able to completely disable delayed ACKs.
Here is an example:
# netstat -s|grep dela
3 delayed acks sent
For all routes enable the knob
# ip route change quickack 1
Generate some traffic across a slow link and we still see the delayed
acks.
# netstat -s|grep dela
106 delayed acks sent
1 delayed acks further delayed because of locked socket
The issue is that both the "ip route change quickack 1" knob and
the TCP_QUICKACK option set the icsk_ack.pingpong variable to 0.
However at the business end in the __tcp_ack_snd_check() routine,
tcp_in_quickack_mode() checks that both icsk_ack.quick != 0
and icsk_ack.pingpong=0 in order to trigger a quickack. As
icsk_ack.quick is determined by heuristics it can be 0. When
that occurs the icsk_ack.pingpong value is ignored and a delayed
ACK is sent regardless.
This patch moves the RTAX_QUICKACK per dst check into the
tcp_in_quickack_mode() routine which ensures that a quickack is
always sent when the quickack knob is enabled for that dst.
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
addr_is_blank() should return true if family is neither AF_INET nor
AF_INET6. This is what its counterpart entity_addr_t::is_blank_ip() is
doing and it is the right thing to do: in process_banner() we check if
our address is blank and if it is "learn" it from our peer. As it is,
we never learn our address and always send out a blank one. This goes
way back to ceph.git commit dd732cbfc1c9 ("use sockaddr_storage; and
some ipv6 support groundwork") from 2009.
While at at, do not open-code ipv6_addr_any() and use INADDR_ANY
constant instead of 0.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Grab a reference on a network namespace of the 'rbd map' (in case of
rbd) or 'mount' (in case of ceph) process and use that to open sockets
instead of always using init_net and bailing if network namespace is
anything but init_net. Be careful to not share struct ceph_client
instances between different namespaces and don't add any code in the
!CONFIG_NET_NS case.
This is based on a patch from Hong Zhiguo <zhiguohong@tencent.com>.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Sage Weil <sage@redhat.com>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree. This batch
mostly comes with patches to address fallout from the previous merge window
cycle, they are:
1) Use entry->state.hook_list from nf_queue() instead of the global nf_hooks
which is not valid when used from NFPROTO_NETDEV, this should cause no
problems though since we have no userspace queueing for that family, but
let's fix this now for the sake of correctness. Patch from Eric W. Biederman.
2) Fix compilation breakage in bridge netfilter if CONFIG_NF_DEFRAG_IPV4 is not
set, from Bernhard Thaler.
3) Use percpu jumpstack in arptables too, now that there's a single copy of the
rule blob we can't store the return address there anymore. Patch from
Florian Westphal.
4) Fix a skb leak in the xmit path of bridge netfilter, problem there since
2.6.37 although it should be not possible to hit invalid traffic there, also
from Florian.
5) Eric Leblond reports that when loading a large ruleset with many missing
modules after a fresh boot, nf_tables can take long time commit it. Fix this
by processing the full batch until the end, even on missing modules, then
abort only once and restart processing.
6) Add bridge netfilter files to the MAINTAINER files.
7) Fix a net_device refcount leak in the new IPV6 bridge netfilter code, from
Julien Grall.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This kernel patch exports the value of the new
ignore_routes_with_linkdown via netconf.
v2: changes to notify userspace via netlink when sysctl values change
and proposed for 'net' since this could be considered a bugfix
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Suggested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit b0e9a30dd6 ("bridge: Add vlan id to multicast groups")
there's a check in br_ip_equal() for a matching vlan id, but the mdb
functions were not modified to use (or at least zero it) so when an
entry was added it would have a garbage vlan id (from the local br_ip
variable in __br_mdb_add/del) and this would prevent it from being
matched and also deleted. So zero out the whole local ip var to protect
ourselves from future changes and also to fix the current bug, since
there's no vlan id support in the mdb uapi - use always vlan id 0.
Example before patch:
root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent
RTNETLINK answers: Invalid argument
After patch:
root@debian:~# bridge mdb add dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb del dev br0 port eth1 grp 239.0.0.1 permanent
root@debian:~# bridge mdb
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Fixes: b0e9a30dd6 ("bridge: Add vlan id to multicast groups")
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling connect() with an AF_TIPC socket would trigger a series
of error messages from SELinux along the lines of:
SELinux: Invalid class 0
type=AVC msg=audit(1434126658.487:34500): avc: denied { <unprintable> }
for pid=292 comm="kworker/u16:5" scontext=system_u:system_r:kernel_t:s0
tcontext=system_u:object_r:unlabeled_t:s0 tclass=<unprintable>
permissive=0
This was due to a failure to initialize the security state of the new
connection sock by the tipc code, leaving it with junk in the security
class field and an unlabeled secid. Add a call to security_sk_clone()
to inherit the security state from the parent socket.
Reported-by: Tim Shearer <tim.shearer@overturenetworks.com>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Paul Moore <paul@paul-moore.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frag needed should be sent only if the inner header asked
to not fragment. Currently fragmentation is broken if the
tunnel has df set, but df was not asked in the original
packet. The tunnel's df needs to be still checked to update
internally the pmtu cache.
Commit 23a3647bc4 broke it, and this commit fixes
the ipv4 df check back to the way it was.
Fixes: 23a3647bc4 ("ip_tunnels: Use skb-len to PMTU check.")
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Gunthorpe reported that since commit c02db8c629 ("rtnetlink: make
SR-IOV VF interface symmetric"), we don't verify IFLA_VF_INFO attributes
anymore with respect to their policy, that is, ifla_vfinfo_policy[].
Before, they were part of ifla_policy[], but they have been nested since
placed under IFLA_VFINFO_LIST, that contains the attribute IFLA_VF_INFO,
which is another nested attribute for the actual VF attributes such as
IFLA_VF_MAC, IFLA_VF_VLAN, etc.
Despite the policy being split out from ifla_policy[] in this commit,
it's never applied anywhere. nla_for_each_nested() only does basic nla_ok()
testing for struct nlattr, but it doesn't know about the data context and
their requirements.
Fix, on top of Jason's initial work, does 1) parsing of the attributes
with the right policy, and 2) using the resulting parsed attribute table
from 1) instead of the nla_for_each_nested() loop (just like we used to
do when still part of ifla_policy[]).
Reference: http://thread.gmane.org/gmane.linux.network/368913
Fixes: c02db8c629 ("rtnetlink: make SR-IOV VF interface symmetric")
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Rony Efraim <ronye@mellanox.com>
Cc: Vlad Zolotarov <vladz@cloudius-systems.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Vlad Zolotarov <vladz@cloudius-systems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e1622baf54.
The side effect of this commit is to add a '@NONE' after each virtual
interface name with a 'ip link'. It may break existing scripts.
Reported-by: Olivier Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
User space can crash kernel with
ip link add ifb10 numtxqueues 100000 type ifb
We must replace a BUG_ON() by proper test and return -EINVAL for
crazy values.
Fixes: 60877a32bc ("net: allow large number of tx queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Start the delete timer when adding temp static entries so they can expire.
Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Fixes: ccb1c31a7a ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: David S. Miller <davem@davemloft.net>
rate estimators are limited to 4 Mpps, which was fine years ago, but
too small with current hardware generation.
Lets use 2^5 scaling instead of 2^10 to get 128 Mpps new limit.
On 64bit arch, use an "unsigned long" for temp storage and remove limit.
(We do not expect 32bit arches to be able to reach this point)
Tested:
tc -s -d filter sh dev eth0 parent ffff:
filter protocol ip pref 1 u32
filter protocol ip pref 1 u32 fh 800: ht divisor 1
filter protocol ip pref 1 u32 fh 800::800 order 2048 key ht 800 bkt 0 flowid 1:15
match 07000000/ff000000 at 12
action order 1: gact action drop
random type none pass val 0
index 1 ref 1 bind 1 installed 166 sec
Action statistics:
Sent 39734251496 bytes 863788076 pkt (dropped 863788117, overlimits 0 requeues 0)
rate 4067Mbit 11053596pps backlog 0b 0p requeues 0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like act_gact, act_mirred can be lockless in packet processing
1) Use percpu stats
2) update lastuse only every clock tick to avoid false sharing
3) use rcu to protect tcfm_dev
4) Remove spinlock usage, as it is no longer needed.
Next step : add multi queue capability to ifb device
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: John Fastabend <john.fastabend@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Final step for gact RCU operation :
1) Use percpu stats
2) update lastuse only every clock tick to avoid false sharing
3) Remove spinlock acquisition, as it is no longer needed.
Since this is the last contended lock in packet RX when tc gact is used,
this gives impressive gain.
My host with 8 RX queues was handling 5 Mpps before the patch,
and more than 11 Mpps after patch.
Tested:
On receiver :
dev=eth0
tc qdisc del dev $dev ingress 2>/dev/null
tc qdisc add dev $dev ingress
tc filter del dev $dev root pref 10 2>/dev/null
tc filter del dev $dev pref 10 2>/dev/null
tc filter add dev $dev est 1sec 4sec parent ffff: protocol ip prio 1 \
u32 match ip src 7.0.0.0/8 flowid 1:15 action drop
Sender sends packets flood from 7/8 network
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Third step for gact RCU operation :
Following patch will get rid of spinlock protection,
so we need to read tcfg_ptype once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second step for gact RCU operation :
We want to get rid of the spinlock protecting gact operations.
Stats (packets/bytes) will soon be per cpu.
gact_determ() would not work without a central packet counter,
so lets add it for this mode.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step for gact RCU operation :
Instead of testing if tcfg_pval is zero or not, just make it 1.
No change in behavior, but slightly faster code.
The smp_rmb()/smp_wmb() barriers, while not strictly needed at this
stage are added for upcoming spinlock removal.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse existing percpu infrastructure John Fastabend added for qdisc.
This patch adds a new cpustats parameter to tcf_hash_create() and all
actions pass false, meaning this patch should have no effect yet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YOSHIFUJI Hideaki/吉藤英明