platform_get_irq_byname() might return -errno which later would be cast
to an unsigned int and used in IRQ handling code leading to usage of
wrong ID and errors about wrong irq_base.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Peng Ma <peng.ma@nxp.com>
Tested-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20191004150826.6656-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Yegor Yefremov <yegorslists@googlemail.com> reported that musb and ftdi
uart can fail for the first open of the uart unless connected using
a hub.
This is because the first dma call done by musb_ep_program() must wait
if cppi41 is PM runtime suspended. Otherwise musb_ep_program() continues
with other non-dma packets before the DMA transfer is started causing at
least ftdi uarts to fail to receive data.
Let's fix the issue by waking up cppi41 with PM runtime calls added to
cppi41_dma_prep_slave_sg() and return NULL if still idled. This way we
have musb_ep_program() continue with PIO until cppi41 is awake.
Fixes: fdea2d09b9 ("dmaengine: cppi41: Add basic PM runtime support")
Reported-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.9+
Link: https://lore.kernel.org/r/20191023153138.23442-1-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Whenever we reset the channel, we need to clear desc_pendingcount
along with desc_submitcount. Otherwise when a new transaction is
submitted, the irq coalesce level could be programmed to an incorrect
value in the axidma case.
This behavior can be observed when terminating pending transactions
with xilinx_dma_terminate_all() and then submitting new transactions
without releasing and requesting the channel.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-8-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver should not run out of tx segments in normal operation. But,
if the user attempts to prepare a transaction with a large sg list,
the driver may not have enough free segments to accommodate the request.
Log a message at the debug level to inform the user in case they are
experiencing issues.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-7-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Take advantage of dmaengine_desc_get_callback_invoke which allows either
a callback or callback_result to be specified. This can be useful when
using the AXI DMA transfer unknown quantities of data where the residue
contained in the result can be used to calculate the number of bytes
transferred.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-6-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce a function that can calculate residues for IPs that support it:
AXI DMA and CDMA.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-5-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dma api provides a single interface to get the appropriate callback
and invoke it directly. Prefer using it.
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In descriptor cleanup the call to desc_callback_valid can be safely
removed as both callback pointers i.e callback_result and callback
are anyway checked in invoke(). There is no much benefit in having
redundant checks.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Nicholas Graumann <nick.graumann@gmail.com>
Reviewed-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Link: https://lore.kernel.org/r/1571150904-3988-2-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Driver for Socionext Milbeaut HDMAC controller. The controller has
upto 8 floating channels, that need a predefined slave-id to work
from a set of slaves.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/20191015033359.14925-1-jassisinghbrar@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
bam_dma_terminate_all() will leak resources if any of the transactions are
committed to the hardware (present in the desc fifo), and not complete.
Since bam_dma_terminate_all() does not cause the hardware to be updated,
the hardware will still operate on any previously committed transactions.
This can cause memory corruption if the memory for the transaction has been
reassigned, and will cause a sync issue between the BAM and its client(s).
Fix this by properly updating the hardware in bam_dma_terminate_all().
Fixes: e7c0fe2a5c ("dmaengine: add Qualcomm BAM dma driver")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191017152606.34120-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
DPPA2(Data Path Acceleration Architecture 2) qDMA supports
virtualized channel by allowing DMA jobs to be enqueued into
different work queues. Core can initiate a DMA transaction by
preparing a frame descriptor(FD) for each DMA job and enqueuing
this job through a hardware portal. DPAA2 components can also
prepare a FD and enqueue a DMA job through a hardware portal.
The qDMA prefetches DMA jobs through DPAA2 hardware portal. It
then schedules and dispatches to internal DMA hardware engines,
which generate read and write requests. Both qDMA source data and
destination data can be either contiguous or non-contiguous using
one or more scatter/gather tables.
The qDMA supports global bandwidth flow control where all DMA
transactions are stalled if the bandwidth threshold has been reached.
Also supported are transaction based read throttling.
Add NXP dppa2 qDMA to support some of Layerscape SoCs.
such as: LS1088A, LS208xA, LX2, etc.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20190930020440.7754-2-peng.ma@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The MC(Management Complex) exports the DPDMAI(Data Path DMA Interface)
object as an interface to operate the DPAA2(Data Path Acceleration
Architecture 2) qDMA Engine. The DPDMAI enables sending frame-based
requests to qDMA and receiving back confirmation response on transaction
completion, utilizing the DPAA2 QBMan(Queue Manager and Buffer Manager
hardware) infrastructure. DPDMAI object provides up to two priorities for
processing qDMA requests.
The following list summarizes the DPDMAI main features and capabilities:
1. Supports up to two scheduling priorities for processing
service requests.
- Each DPDMAI transmit queue is mapped to one of two service
priorities, allowing further prioritization in hardware between
requests from different DPDMAI objects.
2. Supports up to two receive queues for incoming transaction
completion confirmations.
- Each DPDMAI receive queue is mapped to one of two receive
priorities, allowing further prioritization between other
interfaces when associating the DPDMAI receive queues to DPIO
or DPCON(Data Path Concentrator) objects.
3. Supports different scheduling options for processing received
packets:
- Queues can be configured either in 'parked' mode (default),
or attached to a DPIO object, or attached to DPCON object.
4. Allows interaction with one or more DPIO objects for
dequeueing/enqueueing frame descriptors(FD) and for
acquiring/releasing buffers.
5. Supports enable, disable, and reset operations.
Add dpdmai to support some platforms with dpaa2 qdma engine.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Link: https://lore.kernel.org/r/20190930020440.7754-1-peng.ma@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If we terminate the channel to free all descriptors associated with this
channel, we will leak the memory of current descriptor if the current
descriptor is not completed, since it had been deteled from the desc_issued
list and have not been added into the desc_completed list.
Thus we should check if current descriptor is completed or not, when freeing
the descriptors associated with one channel, if not, we should free it to
avoid this issue.
Fixes: 9b3b8171f7 ("dmaengine: sprd: Add Spreadtrum DMA driver")
Reported-by: Zhenfang Wang <zhenfang.wang@unisoc.com>
Tested-by: Zhenfang Wang <zhenfang.wang@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/170dbbc6d5366b6fa974ce2d366652e23a334251.1570609788.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In vdma_channel_set_config clear the delay, frame count and master mask
before updating their new values. It avoids programming incorrect state
when input parameters are different from default.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Acked-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/1569495060-18117-3-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In dma probe, the driver checks for devm_clk_get return and print error
message in the failing case. However for -EPROBE_DEFER this message is
confusing so avoid it.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/1569495060-18117-5-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace the chain of platform_get_resource() and devm_ioremap_resource()
with devm_platform_ioremap_resource(). It simplifies the flow and there
is no functional change.
Fixes below cocinelle warning-
WARNING: Use devm_platform_ioremap_resource for xdev -> regs
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Link: https://lore.kernel.org/r/1569495060-18117-4-git-send-email-radhey.shyam.pandey@xilinx.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Don't populate the array 'handler' on the stack but instead make it
static const. Makes the object code smaller by 80 bytes.
Before:
text data bss dec hex filename
38225 9084 64 47373 b90d drivers/dma/iop-adma.o
After:
text data bss dec hex filename
38081 9148 64 47293 b8bd drivers/dma/iop-adma.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190905163726.19690-1-colin.king@canonical.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On some platforms the clock can be fixed rate, always running one and
there is no need to do anything with it.
In order to support those platforms, switch to use optional clock.
Fixes: f8d9ddbc28 ("dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake")
Depends-on: 60b8f0ddf1 ("clk: Add (devm_)clk_get_optional() functions")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190924085116.83683-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(41) exceed the size of structure sdma_script_start_addrs(40),
thus cause memory corrupt such as slob block header so that kernel
trap into while() loop forever in slob_free(). Please refer to below
code piece in imx-sdma.c:
for (i = 0; i < sdma->script_number; i++)
if (addr_arr[i] > 0)
saddr_arr[i] = addr_arr[i]; /* memory corrupt here */
That issue was brought by commit a572460be9 ("dmaengine: imx-sdma: Add
support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(38->41 3 scripts added) not align with script number added in
sdma_script_start_addrs(2 scripts).
Fixes: a572460be9 ("dmaengine: imx-sdma: Add support for version 3 firmware")
Cc: stable@vger.kernel
Link: https://www.spinics.net/lists/arm-kernel/msg754895.html
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Jurgen Lambrecht <J.Lambrecht@TELEVIC.com>
Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com
[vkoul: update the patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/85de79fa-1ca5-a1e5-0296-9e8a2066f134@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/d36b6a6c-2e3d-8d68-6ddc-969a377ca3b2@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/366e776c-8760-eeb7-c248-7380c9f4fd34@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation a bit by using
a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/c7e3bbae-44fa-9019-18ee-c6cdfd7c2a14@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/aaed7862-49bb-e368-3e7b-5cc2c3d915b1@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation a bit by using
a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://lore.kernel.org/r/5dd19f28-349a-4957-ea3a-6aebbd7c97e2@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/377247f3-b53a-a9d9-66c7-4b8515de3809@web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
>From Tegra186 onwards OUTSTANDING_REQUESTS field is added in channel
configuration register(bits 7:4) which defines the maximum number of reads
from the source and writes to the destination that may be outstanding at
any given point of time. This field must be programmed with a value
between 1 and 8. A value of 0 will prevent any transfers from happening.
Thus added 'has_outstanding_reqs' bool member in chip data structure and is
set to false for Tegra210, since the field is not applicable. For Tegra186
it is set to true and channel configuration is updated with maximum
outstanding requests.
Fixes: 433de642a7 ("dmaengine: tegra210-adma: add support for Tegra186/Tegra194")
Cc: stable@vger.kernel.org
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/1568626513-16541-1-git-send-email-spujar@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch adds dma-channel-mask property support not to reserve
some DMA channels for some reasons. (for example: a heterogeneous
CPU uses it.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1568010892-17606-5-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch uses devm_platform_ioremap_resource() instead of
using platform_get_resource() and devm_ioremap_resource() together
to simplify.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/1568010892-17606-4-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since we will have changed memory mapping of the DMAC in the future,
this patch uses of_data values instead of a macro to calculate
each channel's base offset.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Link: https://lore.kernel.org/r/1568010892-17606-3-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will set the link-list pointer register point to next link-list
configuration's physical address, which can load DMA configuration
from the link-list node automatically.
But the link-list node's physical address can be larger than 32bits,
and now Spreadtrum DMA driver only supports 32bits physical address,
which may cause loading a incorrect DMA configuration when starting
the link-list transfer mode. According to the DMA datasheet, we can
use SRC_BLK_STEP register (bit28 - bit31) to save the high bits of the
link-list node's physical address to fix this issue.
Fixes: 4ac6954647 ("dmaengine: sprd: Support DMA link-list mode")
Signed-off-by: Zhenfang Wang <zhenfang.wang@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/eadfe9295499efa003e1c344e67e2890f9d1d780.1568267061.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
drivers/dma/ti/edma.c: In function edma_probe:
drivers/dma/ti/edma.c:2252:11: warning:
variable off set but not used [-Wunused-but-set-variable]
'off' is not used now, so remove it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190905060249.23928-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Replace the chain of platform_get_resource() and devm_ioremap_resource()
with devm_platform_ioremap_resource().
This allows to remove the local variable for (struct resource *), and
have one function call less.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Link: https://lore.kernel.org/r/20190905034133.29514-1-yamada.masahiro@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- boot_mem_map is removed, providing a nice cleanup made possible by the
recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs or
MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of Vincenzo
Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic SoCs.
- pte_special() is now supported for some configurations, allowing among
other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil, mostly
enabled by the inclusion of the new TCU (timer-counter unit) drivers
he's spent a very patient year or so working on. Plus some fixes for
X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXYaqpRUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2JUQD+PQGFIlq9bo/3vLyqsXJffm+DhwVQ
4WSCSeN5brPkO8EA/153sRJBlRtG+KK5p9f7WYKUuBfbcEawuc1uwmKuy7cG
=lWlM
-----END PGP SIGNATURE-----
Merge tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Main MIPS changes:
- boot_mem_map is removed, providing a nice cleanup made possible by
the recent removal of bootmem.
- Some fixes to atomics, in general providing compiler barriers for
smp_mb__{before,after}_atomic plus fixes specific to Loongson CPUs
or MIPS32 systems using cmpxchg64().
- Conversion to the new generic VDSO infrastructure courtesy of
Vincenzo Frascino.
- Removal of undefined behavior in set_io_port_base(), fixing the
behavior of some MIPS kernel configurations when built with recent
clang versions.
- Initial MIPS32 huge page support, functional on at least Ingenic
SoCs.
- pte_special() is now supported for some configurations, allowing
among other things generic fast GUP to be used.
- Miscellaneous fixes & cleanups.
And platform specific changes:
- Major improvements to Ingenic SoC support from Paul Cercueil,
mostly enabled by the inclusion of the new TCU (timer-counter unit)
drivers he's spent a very patient year or so working on. Plus some
fixes for X1000 SoCs from Zhou Yanjie.
- Netgear R6200 v1 systems are now supported by the bcm47xx platform.
- DT updates for BMIPS, Lantiq & Microsemi Ocelot systems"
* tag 'mips_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (89 commits)
MIPS: Detect bad _PFN_SHIFT values
MIPS: Disable pte_special() for MIPS32 with RiXi
MIPS: ralink: deactivate PCI support for SOC_MT7621
mips: compat: vdso: Use legacy syscalls as fallback
MIPS: Drop Loongson _CACHE_* definitions
MIPS: tlbex: Remove cpu_has_local_ebase
MIPS: tlbex: Simplify r3k check
MIPS: Select R3k-style TLB in Kconfig
MIPS: PCI: refactor ioc3 special handling
mips: remove ioremap_cachable
mips/atomic: Fix smp_mb__{before,after}_atomic()
mips/atomic: Fix loongson_llsc_mb() wreckage
mips/atomic: Fix cmpxchg64 barriers
MIPS: Octeon: remove duplicated include from dma-octeon.c
firmware: bcm47xx_nvram: Allow COMPILE_TEST
firmware: bcm47xx_nvram: Correct size_t printf format
MIPS: Treat Loongson Extensions as ASEs
MIPS: Remove dev_err() usage after platform_get_irq()
MIPS: dts: mscc: describe the PTP ready interrupt
MIPS: dts: mscc: describe the PTP register range
...
- Move Dmaengine DT bindings to YAML and convert Allwinner to schema.
- FSL dma device_synchronize implementation
- DW split acpi and of helpers and updates to driver and support for Elkhart
Lake
- Move filter fn as private for omap-dma and edma drivers and improvements
to these drivers
- Mark expected switch fall-through in couple of drivers
- Renames of shdma and nbpfaxi binding document
- Minor updates to bunch of drivers
-----BEGIN PGP SIGNATURE-----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=Q8bz
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Move Dmaengine DT bindings to YAML and convert Allwinner to schema.
- FSL dma device_synchronize implementation
- DW split acpi and of helpers and updates to driver and support for
Elkhart Lake
- Move filter fn as private for omap-dma and edma drivers and
improvements to these drivers
- Mark expected switch fall-through in couple of drivers
- Renames of shdma and nbpfaxi binding document
- Minor updates to bunch of drivers
* tag 'dmaengine-5.4-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (55 commits)
dmaengine: ti: edma: Use bitmap_set() instead of open coded edma_set_bits()
dmaengine: ti: edma: Only reset region0 access registers
dmaengine: ti: edma: Do not reset reserved paRAM slots
dmaengine: iop-adma.c: fix printk format warning
dmaengine: stm32-dma: Use struct_size() helper
dt-bindings: dmaengine: dma-common: Fix the dma-channel-mask property
dmanegine: ioat/dca: Use struct_size() helper
dmaengine: iop-adma: remove set but not used variable 'slots_per_op'
dmaengine: dmatest: Add support for completion polling
dmaengine: ti: omap-dma: Remove variable override in omap_dma_tx_status()
dmaengine: ti: omap-dma: Remove 'Assignment in if condition'
dmaengine: ti: edma: Remove 'Assignment in if condition'
dmaengine: dw: platform: Split OF helpers to separate module
dmaengine: dw: platform: Split ACPI helpers to separate module
dmaengine: dw: platform: Move handle check to dw_dma_acpi_controller_register()
dmaengine: dw: platform: Switch to acpi_dma_controller_register()
dmaengine: dw: platform: Use devm_platform_ioremap_resource()
dmaengine: dw: platform: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw: platform: Use struct dw_dma_chip_pdata
dmaengine: dw: Export struct dw_dma_chip_pdata for wider use
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
The BCM2835 DMA controller is capable of synthesizing zeroes instead of
copying them from a source address. The feature is enabled by setting
the SRC_IGNORE bit in the Transfer Information field of a Control Block:
"Do not perform source reads.
In addition, destination writes will zero all the write strobes.
This is used for fast cache fill operations."
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
The feature is only available on 8 of the 16 channels. The others are
so-called "lite" channels with a limited feature set and performance.
Enable the feature if a cyclic transaction copies from the zero page.
This reduces traffic on the memory bus.
A forthcoming use case is the BCM2835 SPI driver, which will cyclically
copy from the zero page to the TX FIFO. The idea to use SRC_IGNORE was
taken from an ancient GitHub conversation between Martin and Noralf:
https://github.com/msperl/spi-bcm2835/issues/13#issuecomment-98180451
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/b2286c904408745192e4beb3de3c88f73e4a7210.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the BCM2835 DMA driver's device data structure so that upcoming
commits may add further members with proper kerneldoc.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/78648f80f67d97bb7beecc1b9be6b6e4a45bc1d8.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA engine API requires DMA drivers to explicitly allow that
descriptors are prepared once and reused multiple times. Only a
single driver makes use of this functionality so far (pxa_dma.c,
to speed up pxa_camera.c).
We're about to add another use case for reusable descriptors in
the BCM2835 SPI driver, so allow that in the BCM2835 DMA driver.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/bfc98a38225bbec4158440ad06cb9eee675e3e6f.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The BCM2835 DMA driver currently requests an interrupt from the
controller regardless whether or not the client has passed in the
DMA_PREP_INTERRUPT flag. This causes unnecessary overhead for cyclic
transactions which do not need an interrupt after each period.
We're about to add such a use case, namely cyclic clearing of the SPI
controller's RX FIFO, so amend the DMA driver to request an interrupt
only if DMA_PREP_INTERRUPT was passed in. Ignore the period_len for
such transactions and set it to the buffer length to make the driver's
calculations work.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/73cf37be56eb4cbe6f696057c719f3a38cbaf26e.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Some late fixes for drivers:
- memory leak in ti crossbar dma driver
- cleanup of omap dma probe
- Fix for link list configuration in sprd dma driver
- Handling fixed for DMACHCLR if iommu is mapped in rcar dma
-----BEGIN PGP SIGNATURE-----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=rSgu
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.3' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Some late fixes for drivers:
- memory leak in ti crossbar dma driver
- cleanup of omap dma probe
- Fix for link list configuration in sprd dma driver
- Handling fixed for DMACHCLR if iommu is mapped in rcar dma"
* tag 'dmaengine-fix-5.3' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Fix DMACHCLR handling if iommu is mapped
dmaengine: sprd: Fix the DMA link-list configuration
dmaengine: ti: omap-dma: Add cleanup in omap_dma_probe()
dmaengine: ti: dma-crossbar: Fix a memory leak bug
The commit 20c169aceb ("dmaengine: rcar-dmac: clear pertinence
number of channels") forgets to clear the last channel by
DMACHCLR in rcar_dmac_init() (and doesn't need to clear the first
channel) if iommu is mapped to the device. So, this patch fixes it
by using "channels_mask" bitfield.
Note that the hardware and driver don't support more than 32 bits
in DMACHCLR register anyway, so this patch should reject more than
32 channels in rcar_dmac_parse_of().
Fixes: 20c169aceb ("dmaengine: rcar-dmac: clear pertinence number of channels")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1567424643-26629-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the Spreadtrum DMA link-list mode, when the DMA engine got a slave
hardware request, which will trigger the DMA engine to load the DMA
configuration from the link-list memory automatically. But before the
slave hardware request, the slave will get an incorrect residue due
to the first node used to trigger the link-list was configured as the
last source address and destination address.
Thus we should make sure the first node was configured the start source
address and destination address, which can fix this issue.
Fixes: 4ac6954647 ("dmaengine: sprd: Support DMA link-list mode")
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/77868edb7aff9d5cb12ac3af8827ef2e244441a6.1567150471.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix printk format warning in iop-adma.c (seen on x86_64) by using
%pad:
../drivers/dma/iop-adma.c:118:12: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 6 has type ‘dma_addr_t {aka long long unsigned int}’ [-Wformat=]
Fixes: c211092313 ("dmaengine: driver for the iop32x, iop33x, and iop13xx raid engines")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Link: https://lore.kernel.org/r/1803541f-98a6-7cce-b050-ff1e9a333ab2@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct stm32_dma_desc {
...
struct stm32_dma_sg_req sg_req[];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following function:
static struct stm32_dma_desc *stm32_dma_alloc_desc(u32 num_sgs)
{
return kzalloc(sizeof(struct stm32_dma_desc) +
sizeof(struct stm32_dma_sg_req) * num_sgs, GFP_NOWAIT);
}
with:
kzalloc(struct_size(desc, sg_req, num_sgs), GFP_NOWAIT)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190830161423.GA3483@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct ioat_dca_priv {
...
struct ioat_dca_slot req_slots[0];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*ioatdca) + (sizeof(struct ioat_dca_slot) * slots)
with:
struct_size(ioatdca, req_slots, slots)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20190828184015.GA4273@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/dma/iop-adma.c: In function iop_adma_tx_submit:
drivers/dma/iop-adma.c:367:6: warning:
variable slots_per_op set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190821121908.7468-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the polled parameter the DMA drivers can be tested if they can work
correctly when no completion is requested (no DMA_PREP_INTERRUPT and no
callback is provided).
If polled mode is selected then use dma_sync_wait() to execute the test
iteration instead of relying on the completion callback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190731071438.24075-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is no need to fetch local omap_desc since the desc we have is the
correct one already when we need to check the channel status.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190730132029.2971-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While the compiler does not have problem with how it is implemented,
checkpatch does give en ERROR for this arrangement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190730132015.2863-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
While the compiler does not have problem with how it is implemented,
checkpatch does give en ERROR for this arrangement.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190730132006.2790-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Hi Linus,
Please, pull the following patches that mark switch cases where we are
expecting to fall through.
- Fix fall-through warnings on arm and mips for multiple
configurations.
Thanks
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
-----BEGIN PGP SIGNATURE-----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=fQZm
-----END PGP SIGNATURE-----
Merge tag 'Wimplicit-fallthrough-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull more fallthrough fixes from Gustavo A. R. Silva:
"Fix fall-through warnings on arm and mips for multiple configurations"
* tag 'Wimplicit-fallthrough-5.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux:
video: fbdev: acornfb: Mark expected switch fall-through
scsi: libsas: sas_discover: Mark expected switch fall-through
MIPS: Octeon: Mark expected switch fall-through
power: supply: ab8500_charger: Mark expected switch fall-through
watchdog: wdt285: Mark expected switch fall-through
mtd: sa1100: Mark expected switch fall-through
drm/sun4i: tcon: Mark expected switch fall-through
drm/sun4i: sun6i_mipi_dsi: Mark expected switch fall-through
ARM: riscpc: Mark expected switch fall-through
dmaengine: fsldma: Mark expected switch fall-through
Move ACPI handle check to the dw_dma_acpi_controller_register().
While here, convert it to has_acpi_companion() which is recommended way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-9-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a possibility to have registered ACPI DMA controller
while it has been gone already.
To avoid the potential crash, move to non-managed
acpi_dma_controller_register().
Fixes: 42c91ee71d ("dw_dmac: add ACPI support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-8-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel® PSE (Programmable Services Engine) provides few DMA controllers
to the host on Intel Elkhart Lake. Enable them in the ACPI glue driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We are expecting some devices can be enumerated either as PCI or ACPI.
Nevertheless, they will share same information, thus, provide a generic
struct dw_dma_chip_pdata for all glue drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Kernel documentation script is not happy about absence of function parameter
descriptions:
drivers/dma/acpi-dma.c:163: warning: Function parameter or member 'data' not described in 'acpi_dma_controller_register'
drivers/dma/acpi-dma.c:247: warning: Function parameter or member 'data' not described in 'devm_acpi_dma_controller_register'
drivers/dma/acpi-dma.c:274: warning: Function parameter or member 'dev' not described in 'devm_acpi_dma_controller_free'
Append the descriptions of above mentioned function parameters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
CSRT has an information about address width, which is supported by
the certain DMA controller.
Use information from CSRT to set up DMA mask for shared controller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20190820131546.75744-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Mark switch cases where we are expecting to fall through.
Fix the following warnings (Building: powerpc-ppa8548_defconfig powerpc):
drivers/dma/fsldma.c: In function ‘fsl_dma_chan_probe’:
drivers/dma/fsldma.c:1165:26: warning: this statement may fall through [-Wimplicit-fallthrough=]
chan->toggle_ext_pause = fsl_chan_toggle_ext_pause;
~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/dma/fsldma.c:1166:2: note: here
case FSL_DMA_IP_83XX:
^~~~
Reported-by: kbuild test robot <lkp@intel.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
If devm_request_irq() fails to disable all interrupts, no cleanup is
performed before retuning the error. To fix this issue, invoke
omap_dma_free() to do the cleanup.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/1565938570-7528-1-git-send-email-wenwen@cs.uga.edu
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In ti_dra7_xbar_probe(), 'rsv_events' is allocated through kcalloc(). Then
of_property_read_u32_array() is invoked to search for the property.
However, if this process fails, 'rsv_events' is not deallocated, leading to
a memory leak bug. To fix this issue, free 'rsv_events' before returning
the error.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/1565938136-7249-1-git-send-email-wenwen@cs.uga.edu
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The alignment of mux_configure32() and fsl_edma_chan_mux() need
to be adjusted, it must start precisely at the first column after
the openning parenthesis of the first line.
Fixes: 9d831528a6 ("dmaengine: fsl-edma: extract common fsl-edma code (no changes in behavior intended)")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Link: https://lore.kernel.org/r/20190814072105.144107-3-maowenan@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is one sparse warning in drivers/dma/fsl-edma-common.c:
drivers/dma/fsl-edma-common.c:93:6: warning: symbol 'mux_configure32'
was not declared. Should it be static?
Fix it by setting mux_configure32() as static.
Fixes: 232a7f18cf ("dmaengine: fsl-edma: add i.mx7ulp edma2 version support")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Link: https://lore.kernel.org/r/20190814072105.144107-2-maowenan@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Clang produces the following warning
drivers/dma/mv_xor_v2.c:264:40: warning: shifting a negative signed value
is undefined [-Wshift-negative-value]
reg &= (~MV_XOR_V2_DMA_IMSG_THRD_MASK <<
MV_XOR_V2_DMA_IMSG_THRD_SHIFT);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
drivers/dma/mv_xor_v2.c:271:46: warning: shifting a negative signed value
is undefined [-Wshift-negative-value]
reg &= (~MV_XOR_V2_DMA_IMSG_TIMER_THRD_MASK <<
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^
Upon further investigation MV_XOR_V2_DMA_IMSG_THRD_SHIFT and
MV_XOR_V2_DMA_IMSG_TIMER_THRD_SHIFT are both 0. Since shifting by 0 does
nothing, these variables can be removed.
Cc: clang-built-linux@googlegroups.com
Link: https://github.com/ClangBuiltLinux/linux/issues/521
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20190813173448.109859-1-nhuck@google.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake Offload Service Engine (OSE) will be called as
Intel(R) Programmable Services Engine (Intel(R) PSE) in documentation.
Update the comment here accordingly.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20190813080602.15376-1-jarkko.nikula@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Now that iop3xx and iop13xx are gone, the iop-adma driver no
longer needs to deal with incompatible register layout defined
in machine specific header files.
Move the iop32x specific definitions into drivers/dma/iop-adma.h
and the platform_data into include/linux/platform_data/dma-iop32x.h,
and change the machine code to no longer reference those.
The DMA0_ID/DMA1_ID/AAU_ID macros are required as part of the
platform data interface and still need to be visible, so move
those from one header to the other.
Link: https://lore.kernel.org/r/20190809163334.489360-4-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When compile-testing on other architectures, we get lots of warnings
about incorrect format strings, like:
drivers/dma/iop-adma.c: In function 'iop_adma_alloc_slots':
drivers/dma/iop-adma.c:307:6: warning: format '%x' expects argument of type 'unsigned int', but argument 6 has type 'dma_addr_t {aka long long unsigned int}' [-Wformat=]
drivers/dma/iop-adma.c: In function 'iop_adma_prep_dma_memcpy':
>> drivers/dma/iop-adma.c:518:40: warning: format '%u' expects argument of type 'unsigned int', but argument 5 has type 'size_t {aka long unsigned int}' [-Wformat=]
Use %zu for printing size_t as required, and cast the dma_addr_t
arguments to 'u64' for printing with %llx. Ideally this should use
the %pad format string, but that requires an lvalue argument that
doesn't work here.
Link: https://lore.kernel.org/r/20190809163334.489360-3-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Compile-testing this driver fails on m68k without the
extra header inclusion.
Link: https://lore.kernel.org/r/20190809163334.489360-2-arnd@arndb.de
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are three families of IOP machines we support in Linux: iop32x
(which includes EP80219), iop33x and iop13xx (aka IOP34x aka WP8134x).
All products we support in the kernel are based on the first of these,
iop32x, the other families only ever supported the Intel reference
boards but no actual machine anyone could ever buy.
While one could clearly make them all three work in a single kernel
with some work, this takes the easy way out, removing the later two
platforms entirely, under the assumption that there are no remaining
users.
Earlier versions of OpenWRT and Debian both had support for iop32x
but not the others, and they both dropped iop32x as well in their 2015
releases.
Link: https://lore.kernel.org/r/20190809163334.489360-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de> # for I2C parts
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mark switch cases where we are expecting to fall through.
Fix the following warning (Building: powerpc-ppa8548_defconfig powerpc):
drivers/dma/fsldma.c: In function ‘fsl_dma_chan_probe’:
drivers/dma/fsldma.c:1165:26: warning: this statement may fall through [-Wimplicit-fallthrough=]
chan->toggle_ext_pause = fsl_chan_toggle_ext_pause;
~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/dma/fsldma.c:1166:2: note: here
case FSL_DMA_IP_83XX:
^~~~
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Link: https://lore.kernel.org/r/20190812002159.GA26899@embeddedor
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The two filter functions are now marked static, but still exported,
which triggers a coming build-time check:
WARNING: "omap_dma_filter_fn" [vmlinux] is a static EXPORT_SYMBOL_GPL
WARNING: "edma_filter_fn" [vmlinux] is a static EXPORT_SYMBOL
Remove the unneeded exports as well, as originally intended.
Fixes: 9c71b9eb3c ("dmaengine: omap-dma: make omap_dma_filter_fn private")
Fixes: d2bfe7b5d1 ("dmaengine: edma: make edma_filter_fn private")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190812101155.997721-1-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The OMAP 4 TRM specifies that when using double-index addressing
the address increases by the ES plus the EI value minus 1 within
a frame. When a full frame is transferred, the address increases
by the ES plus the frame index (FI) value minus 1.
The omap-dma code didn't account for the 'minus 1' in the FI register.
To get correct addressing, add 1 to the src_icg value.
This was found when testing a hacked version of the media m2m-deinterlace.c
driver on a Pandaboard.
The only other source that uses this feature is omap_vout_vrfb.c,
and that adds a + 1 when setting the dst_icg. This is a workaround
for the broken omap-dma.c behavior. So remove the workaround at the
same time that we fix omap-dma.c.
I tested the omap_vout driver with a Beagle XM board to check that
the '+ 1' in omap_vout_vrfb.c was indeed a workaround for the omap-dma
bug.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Link: https://lore.kernel.org/r/952e7f51-f208-9333-6f58-b7ed20d2ea0b@xs4all.nl
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In stm32_mdma_irq_handler(), chan is checked on line 1368.
When chan is NULL, it is still used on line 1369:
dev_err(chan2dev(chan), "MDMA channel not initialized\n");
Thus, a possible null-pointer dereference may occur.
To fix this bug, "dev_dbg(mdma2dev(dmadev), ...)" is used instead.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Fixes: a4ffb13c89 ("dmaengine: Add STM32 MDMA driver")
Link: https://lore.kernel.org/r/20190729020849.17971-1-baijiaju1990@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In function dmac_alloc_resources(), pl330->mcode_cpu is allocated using
dma_alloc_attrs() but freed with dma_free_coherent().
Use the correct dma_free_attrs() function to free pl330->mcode_cpu.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190726105947.25342-1-huangfq.daxian@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Each iteration of for_each_available_child_of_node puts the previous
node, but in the case of a goto from the middle of the loop, there is
no put, thus causing a memory leak.
Hence add an of_node_put under the label that the gotos point to.
In order to avoid decrementing an already-decremented refcount, copy the
original contents of the label (including the return statement) to just
above the label, so that the code under the label is executed only when
a goto exit from the loop occurs.
Additionally, remove an unnecessary get/put pair from the loop, as the
loop itself already keeps track of refcount.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Acked-by: Sinan Kaya <okaya@kernel.org>
Link: https://lore.kernel.org/r/20190724081609.9724-1-nishkadg.linux@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add edma2 for i.mx7ulp by version v3, since v2 has already
been used by mcf-edma.
The big changes based on v1 are belows:
1. only one dmamux.
2. another clock dma_clk except dmamux clk.
3. 16 independent interrupts instead of only one interrupt for
all channels.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/1563952834-7731-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Acked-by: Sinan Kaya <okaya@kernel.org>
Link: https://lore.kernel.org/r/20190715031723.6375-1-huangfq.daxian@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/r/20190715031716.6328-1-huangfq.daxian@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-11-swboyd@chromium.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: arm):
drivers/dma/imx-dma.c: In function ‘imxdma_xfer_desc’:
drivers/dma/imx-dma.c:542:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (slot == IMX_DMA_2D_SLOT_A) {
^
drivers/dma/imx-dma.c:559:2: note: here
case IMXDMA_DESC_MEMCPY:
^~~~
Notice that, in this particular case, the code comment is
modified in accordance with what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20190729225221.GA24269@embeddedor
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The Tegra210 ADMA supports two modes for transferring data to a FIFO
which are ...
1. Transfer data to/from the FIFO as soon as a single burst can be
transferred.
2. Transfer data to/from the FIFO based upon FIFO thresholds, where
the FIFO threshold is specified in terms on multiple bursts.
Currently, the ADMA driver programs the FIFO threshold values in the
FIFO_CTRL register, but never enables the transfer mode that uses
these threshold values. Given that these have never been used so far,
simplify the ADMA driver by removing the programming of these threshold
values.
Signed-off-by: Jonathan Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20190731101639.22755-1-jonathanh@nvidia.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The newer and better JZ4780 driver is now used to provide DMA
functionality on the JZ4740.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
When a DMA client driver does not set the DMA_PREP_INTERRUPT because it
does not want to use interrupts for DMA completion or because it can not
rely on DMA interrupts due to executing the memcpy when interrupts are
disabled it will poll the status of the transfer.
Since we can not tell from any EDMA register that the transfer is
completed, we can only know that the paRAM set has been sent to TPTC for
processing we need to check the residue of the transfer, if it is 0 then
the transfer is completed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190716082655.1620-4-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For memcpy we never stored the start address of the transfer for the pset
which rendered the memcpy residue calculation completely broken.
In the edma_residue() function we also need to to some correction for the
calculations:
Instead waiting for all EDMA channels to be idle (in a busy system it can
take few iteration to hit a point when all queues are idle) wait for the
event pending on the given channel (SH_ER for hw synchronized channels,
SH_ESR for manually triggered channels).
If the position returned by EMDA is 0 it implies that the last paRAM set
has been consumed and we are at the closing dummy set, thus we can conclude
that the transfer is completed and we can return 0 as residue.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[vkoul: fixed typo in commit log]
Link: https://lore.kernel.org/r/20190716082655.1620-3-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Introduce defines for getting the array index and the bit number within the
64bit array register pairs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190716082655.1620-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a DMA client driver does not set the DMA_PREP_INTERRUPT because it
does not want to use interrupts for DMA completion or because it can not
rely on DMA interrupts due to executing the memcpy when interrupts are
disabled it will poll the status of the transfer.
If the interrupts are enabled then the cookie will be set completed in the
interrupt handler so only check in HW completion when the polling is really
needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190716082459.1222-3-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The tx_status is most likely going to be asked for the current transfer, so
check that first then try to fall back to lookup of non started transfers.
In this way the code is a bit more readable and in most cases we will avoid
to run vchan_find_desc() all the time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190716082459.1222-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The current driver works perfectly fine on every generation of the
JZ47xx SoCs, except on the JZ4740.
There, when hardware descriptors are chained together (with the LINK
bit set), the next descriptor isn't automatically fetched as it should -
instead, an interrupt is raised, even if the TIE bit (Transfer Interrupt
Enable) bit is cleared. When it happens, the DMA transfer seems to be
stopped (it doesn't chain), and it's uncertain how many bytes have
actually been transferred.
Until somebody smarter than me can figure out how to make chained
descriptors work on the JZ4740, we now disable chained descriptors on
that particular SoC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20190714215504.10877-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If CONFIG_PM is not set, build warnings:
drivers/dma/tegra210-adma.c:747:12: warning: tegra_adma_runtime_resume defined but not used [-Wunused-function]
static int tegra_adma_runtime_resume(struct device *dev)
drivers/dma/tegra210-adma.c:715:12: warning: tegra_adma_runtime_suspend defined but not used [-Wunused-function]
static int tegra_adma_runtime_suspend(struct device *dev)
Mark the two function as __maybe_unused.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 3145d73e69 ("dmaengine: tegra210-adma: remove PM_CLK dependency")
Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20190709083258.57112-1-yuehaibing@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
clang-9 points out that there are two variables that depending on the
configuration may only be used in an ARRAY_SIZE() expression but not
referenced:
drivers/dma/ste_dma40.c:145:12: error: variable 'd40_backup_regs' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs[] = {
^
drivers/dma/ste_dma40.c:214:12: error: variable 'd40_backup_regs_chan' is not needed and will not be emitted [-Werror,-Wunneeded-internal-declaration]
static u32 d40_backup_regs_chan[] = {
Mark these __maybe_unused to shut up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20190712091357.744515-1-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When building with 'make C=1', sparse reports an endianess bug:
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:60:30: warning: cast removes address space of expression
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: warning: incorrect type in argument 1 (different address spaces)
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: expected void const volatile [noderef] <asn:2>*addr
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: got void *[assigned] ptr
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: warning: incorrect type in argument 1 (different address spaces)
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: expected void const volatile [noderef] <asn:2>*addr
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: got void *[assigned] ptr
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: warning: incorrect type in argument 1 (different address spaces)
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: expected void const volatile [noderef] <asn:2>*addr
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:86:24: got void *[assigned] ptr
The current code is clearly wrong, as it passes an endian-swapped word
into a register function where it gets swapped again. Just pass the variables
directly into lower_32_bits()/upper_32_bits().
Fixes: 7e4b8a4fbe ("dmaengine: Add Synopsys eDMA IP version 0 support")
Link: https://lore.kernel.org/lkml/20190617131820.2470686-1-arnd@arndb.de/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/20190722124457.1093886-3-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The new driver mixes up dma_addr_t and __iomem pointers, which results
in warnings on some 32-bit architectures, like:
drivers/dma/dw-edma/dw-edma-v0-core.c: In function '__dw_regs':
drivers/dma/dw-edma/dw-edma-v0-core.c:28:9: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
return (struct dw_edma_v0_regs __iomem *)dw->rg_region.vaddr;
Make it use __iomem pointers consistently here, and avoid using dma_addr_t
for __iomem tokens altogether.
A small complication here is the debugfs code, which passes an __iomem
token as the private data for debugfs files, requiring the use of
extra __force.
Fixes: 7e4b8a4fbe ("dmaengine: Add Synopsys eDMA IP version 0 support")
Link: https://lore.kernel.org/lkml/20190617131918.2518727-1-arnd@arndb.de/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190722124457.1093886-2-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Putting large constant data on the stack causes unnecessary overhead
and stack usage:
drivers/dma/dw-edma/dw-edma-v0-debugfs.c:285:6: error: stack frame size of 1376 bytes in function 'dw_edma_v0_debugfs_on' [-Werror,-Wframe-larger-than=]
Mark the variable 'static const' in order for the compiler to move it
into the .rodata section where it does no such harm.
Fixes: 305aebeff8 ("dmaengine: Add Synopsys eDMA IP version 0 debugfs support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Link: https://lore.kernel.org/r/20190722124457.1093886-1-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During enabling of the RPi 4, we found out that the driver doesn't provide
a helpful error message in case setting DMA mask fails. So add one.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/1563297318-4900-1-git-send-email-wahrenst@gmx.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
With the audio driver no longer referring to this function, it
can be made private to the dmaengine driver itself, and the
header file removed.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20190722081705.2084961-2-arnd@arndb.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Add support in dmaengine core to do device node checks for DT devices and
update bunch of drivers to use that and remove open coding from drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
-----BEGIN PGP SIGNATURE-----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=R+aC
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Add support in dmaengine core to do device node checks for DT devices
and update bunch of drivers to use that and remove open coding from
drivers
- New driver/driver support for new hardware, namely:
- MediaTek UART APDMA
- Freescale i.mx7ulp edma2
- Synopsys eDMA IP core version 0
- Allwinner H6 DMA
- Updates to axi-dma and support for interleaved cyclic transfers
- Greg's debugfs return value check removals on drivers
- Updates to stm32-dma, hsu, dw, pl330, tegra drivers
* tag 'dmaengine-5.3-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (68 commits)
dmaengine: Revert "dmaengine: fsl-edma: add i.mx7ulp edma2 version support"
dmaengine: at_xdmac: check for non-empty xfers_list before invoking callback
Documentation: dmaengine: clean up description of dmatest usage
dmaengine: tegra210-adma: remove PM_CLK dependency
dmaengine: fsl-edma: add i.mx7ulp edma2 version support
dt-bindings: dma: fsl-edma: add new i.mx7ulp-edma
dmaengine: fsl-edma-common: version check for v2 instead
dmaengine: fsl-edma-common: move dmamux register to another single function
dmaengine: fsl-edma: add drvdata for fsl-edma
dmaengine: Revert "dmaengine: fsl-edma: support little endian for edma driver"
dmaengine: rcar-dmac: Reject zero-length slave DMA requests
dmaengine: dw: Enable iDMA 32-bit on Intel Elkhart Lake
dmaengine: dw-edma: fix semicolon.cocci warnings
dmaengine: sh: usb-dmac: Use [] to denote a flexible array member
dmaengine: dmatest: timeout value of -1 should specify infinite wait
dmaengine: dw: Distinguish ->remove() between DW and iDMA 32-bit
dmaengine: fsl-edma: support little endian for edma driver
dmaengine: hsu: Revert "set HSU_CH_MTSR to memory width"
dmagengine: pl330: add code to get reset property
dt-bindings: pl330: document the optional resets property
...
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
* fix BCH ECC layout for large page NAND parts
* fallback to detected ecc-strength, ecc-step-size
* when oops in progress use pio and interrupt polling
* code refactor code to introduce helper functions
* add support for v7.3 controller
- FSMC:
* use nand_op_trace for operation tracing
- GPMI:
* move all driver code into single file
* various cleanups (including dmaengine changes)
* use runtime PM to manage clocks
* implement exec_op
- MTK:
* correct low level time calculation of r/w cycle
* improve data sampling timing for read cycle
* add validity check for CE# pin setting
* fix wrongly assigned OOB buffer pointer issue
* re-license MTK NAND driver as Dual MIT/GPL
- STM32:
* manage the get_irq error case
* increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl0qLr4ACgkQJWrqGEe9
VoQVCwf/ZCG5CldS3cs6B68kMJoZ/rJyJxBnxtIhffda2vw1KG/12o6XaDO9xA/R
EwYrOTzlYZxzCZsNvWyHepG3Kj3d38CJ52ZqhavjpihwMlKKOgW/K39xuKWCrfxS
sVMLz/UdrcsQfcPGAy7DSyqhzRAtupNxngCdEkIIMGFZWsv4uZfOFEGMrzUJ5RYN
/okIyUE7Iz0dRq1/KXSl365V1MS8QP2eHFuHrUd38+kJ8TJnQjXX3Bmdul4aNTx+
HIIpykovoAn5BZ0YA4lJL90zVoDOWysARwHIAMDvJa8zS0wDTU16Tj2M6AQK+a4x
hbIOOkeX0hTKpJvy7/khli5y1bn2mw==
=L+tV
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"This contains the following changes for MTD:
MTD core changes:
- New Hyperbus framework
- New _is_locked (concat) implementation
- Various cleanups
NAND core changes:
- use longest matching pattern in ->exec_op() default parser
- export NAND operation tracer
- add flag to indicate panic_write in MTD
- use kzalloc() instead of kmalloc() and memset()
Raw NAND controller drivers changes:
- brcmnand:
- fix BCH ECC layout for large page NAND parts
- fallback to detected ecc-strength, ecc-step-size
- when oops in progress use pio and interrupt polling
- code refactor code to introduce helper functions
- add support for v7.3 controller
- FSMC:
- use nand_op_trace for operation tracing
- GPMI:
- move all driver code into single file
- various cleanups (including dmaengine changes)
- use runtime PM to manage clocks
- implement exec_op
- MTK:
- correct low level time calculation of r/w cycle
- improve data sampling timing for read cycle
- add validity check for CE# pin setting
- fix wrongly assigned OOB buffer pointer issue
- re-license MTK NAND driver as Dual MIT/GPL
- STM32:
- manage the get_irq error case
- increase DMA completion timeouts
Raw NAND chips drivers changes:
- Macronix: add read-retry support
Onenand driver changes:
- add support for 8Gb datasize chips
- avoid fall-through warnings
SPI-NAND changes:
- define macros for page-read ops with three-byte addresses
- add support for two-byte device IDs and then for GigaDevice
GD5F1GQ4UFxxG
- add initial support for Paragon PN26G0xA
- handle the case where the last page read has bitflips
SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width
SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control"
* tag 'mtd/for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (60 commits)
mtd: concat: implement _is_locked mtd operation
mtd: concat: refactor concat_lock/concat_unlock
mtd: abi: do not use C++ style comments in uapi header
mtd: afs: remove unneeded NULL check
mtd: rawnand: stm32_fmc2: increase DMA completion timeouts
mtd: rawnand: Use kzalloc() instead of kmalloc() and memset()
mtd: hyperbus: Add driver for TI's HyperBus memory controller
mtd: spinand: read returns badly if the last page has bitflips
mtd: spinand: Add initial support for Paragon PN26G0xA
mtd: rawnand: mtk: Re-license MTK NAND driver as Dual MIT/GPL
mtd: rawnand: gpmi: remove double assignment to block_size
dt-bindings: mtd: brcmnand: Add brcmnand, brcmnand-v7.3 support
mtd: rawnand: brcmnand: Add support for v7.3 controller
mtd: rawnand: brcmnand: Refactored code to introduce helper functions
mtd: rawnand: brcmnand: When oops in progress use pio and interrupt polling
mtd: Add flag to indicate panic_write
mtd: rawnand: Add Macronix NAND read retry support
mtd: onenand: Avoid fall-through warnings
mtd: spinand: Add support for GigaDevice GD5F1GQ4UFxxG
mtd: spinand: Add support for two-byte device IDs
...
This reverts commit 7144afd025 ("dmaengine: fsl-edma: add i.mx7ulp
edma2 version support") as this fails to build with module option due to
usage of of_irq_count() which is not an exported symbol as kernel
drivers are *not* expected to use it (rightly so).
Signed-off-by: Vinod Koul <vkoul@kernel.org>
tx descriptor retrieved from an empty xfers_list may not have valid
pointers to the callback functions.
Avoid calling dmaengine_desc_get_callback_invoke if xfers_list is empty.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
One space is left unused in circular FIFO to differentiate
'full' and 'empty' cases. So take that in to account while
counting for the descriptors completed.
Fixes the issue reported here,
https://lkml.org/lkml/2019/6/18/669
Cc: stable@vger.kernel.org
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It is possible for an irq triggered by channel0 to be received later
after clks are disabled once firmware loaded during sdma probe. If
that happens then clearing them by writing to SDMA_H_INTR won't work
and the kernel will hang processing infinite interrupts. Actually,
don't need interrupt triggered on channel0 since it's pollling
SDMA_H_STATSTOP to know channel0 done rather than interrupt in
current code, just clear BD_INTR to disable channel0 interrupt to
avoid the above case.
This issue was brought by commit 1d069bfa3c ("dmaengine: imx-sdma:
ack channel 0 IRQ in the interrupt handler") which didn't take care
the above case.
Fixes: 1d069bfa3c ("dmaengine: imx-sdma: ack channel 0 IRQ in the interrupt handler")
Cc: stable@vger.kernel.org #5.0+
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Sven Van Asbroeck <thesven73@gmail.com>
Tested-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If probe() fails anywhere beyond the point where
sdma_get_firmware() is called, then a kernel oops may occur.
Problematic sequence of events:
1. probe() calls sdma_get_firmware(), which schedules the
firmware callback to run when firmware becomes available,
using the sdma instance structure as the context
2. probe() encounters an error, which deallocates the
sdma instance structure
3. firmware becomes available, firmware callback is
called with deallocated sdma instance structure
4. use after free - kernel oops !
Solution: only attempt to load firmware when we're certain
that probe() will succeed. This guarantees that the firmware
callback's context will remain valid.
Note that the remove() path is unaffected by this issue: the
firmware loader will increment the driver module's use count,
ensuring that the module cannot be unloaded while the
firmware callback is pending or running.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
[vkoul: fixed braces for if condition]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The "pending" variable was a u32 but we cast it to an unsigned long
pointer when we do the for_each_set_bit() loop. The problem is that on
big endian 64bit systems that results in an out of bounds read.
Fixes: 4e4106f5e9 ("dmaengine: jz4780: Fix transfers being ACKed too soon")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Tegra ADMA does not use pm-clk interface now and hence the dependency
is removed from Kconfig.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add edma2 for i.mx7ulp by version v3, since v2 has already
been used by mcf-edma.
The big changes based on v1 are belows:
1. only one dmamux.
2. another clock dma_clk except dmamux clk.
3. 16 independent interrupts instead of only one interrupt for
all channels.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The next v3 i.mx7ulp edma is based on v1, so change version
check logic for v2 instead.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Prepare for edmav2 on i.mx7ulp whose dmamux register is 32bit. No function
impacted.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are some differences between vf610 and next i.mx7ulp. Put such
differences into static driver data for distinguishing easily at
driver level. Change mcf-edma accordingly.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This reverts commit 002905eca5.
Commit 002905eca5 ("dmaengine: fsl-edma: support little endian for edma
driver") incorrectly assumed that there was not little endian support
in the driver.
This causes hangs on Vybrid, so revert it so that Vybrid systems
could boot again.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The gpmi driver performance suffers from NAND operations being split
in multiple small DMA transfers. This has been forced by the NAND layer
in the former days, but now with exec_op we can use the controller as
intended.
With this patch gpmi_nfc_exec_op becomes the main entry point to NAND
operations. Here all instructions are collected and chained as separate
DMA transfers. In the end whole chain is fired and waited to be
finished. gpmi_nfc_exec_op only does the hardware operations, bad block
marker swapping and buffer scrambling is done by the callers. It's worth
noting that the nand_*_op functions always take the buffer lengths for
the data that the NAND chip actually transfers. When doing BCH we have
to calculate the net data size from the raw data size in some places.
This patch has been tested with 2048/64 and 2048/128 byte NAND on
i.MX6q. mtd_oobtest, mtd_subpagetest and mtd_speedtest run without
errors. nandbiterrs, nandpagetest and nandsubpagetest userspace tests
from mtdutils run without errors and UBIFS can successfully be mounted.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver uses the flags parameter in dmaengine_prep_slave_sg() for
custom flags, but still uses the dmaengine specific names of the flags.
Do a little bit better and at least give the flag a custom name.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver can do PIO transfers. A pointer to the PIO words
to transfer is passed in the struct scatterlist * argument of
dmaengine_prep_slave_sg(). It's quite ugly and non obvious to cast
u32 * to struct scatterlist * each time when calling
dmaengine_prep_slave_sg(), so add a static inline wrapper function
to be called by the user along with a description what is going on.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The mxs dma driver insists on having the DMA_PREP_INTERRUPT flag set
on all but the first transfer. There's no need to let the user set this
flag, the driver can do it internally whenever it needs it. Drop
handling of this flag from the driver.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
While the .device_prep_slave_sg() callback rejects empty scatterlists,
it still accepts single-entry scatterlists with a zero-length segment.
These may happen if a driver calls dmaengine_prep_slave_single() with a
zero len parameter. The corresponding DMA request will never complete,
leading to messages like:
rcar-dmac e7300000.dma-controller: Channel Address Error happen
and DMA timeouts.
Although requesting a zero-length DMA request is a driver bug, rejecting
it early eases debugging. Note that the .device_prep_dma_memcpy()
callback already rejects requests to copy zero bytes.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Analyzed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Intel Elkhart Lake OSE (Offload Service Engine) provides few DMA controllers
to the host. Enable them in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Flexible array members should be denoted using [] instead of [0], else
gcc will not warn when they are no longer at the end of the structure.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dmatest module parameter 'timeout' is documented as accepting a
-1 to mean "infinite timeout". However, an infinite timeout is not
advised, nor possible since the module parameter is an unsigned int,
which won't accept a negative value. Change the parameter
comment to reflect current behavior, which allows values from 0 up to
4294967295 (0xFFFFFFFF).
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the same way as done for ->probe(), call ->remove() based on
the type of the hardware.
While it works now due to equivalency of the two removal functions,
it might be changed in the future.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The commit
080edf75d3 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
has been mistakenly submitted. The further investigations show that
the original code does better job since the memory side transfer size
has never been configured by DMA users.
As per latest revision of documentation: "Channel minimum transfer size
(CHnMTSR)... For IOSF UART, maximum value that can be programmed is 64 and
minimum value that can be programmed is 1."
This reverts commit 080edf75d3.
Fixes: 080edf75d3 ("dmaengine: hsu: set HSU_CH_MTSR to memory width")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DMA controller on some SoCs can be held in reset, and thus requires
the reset signal(s) to deasserted. Most SoCs will have just one reset
signal, but there are others, i.e. Arria10/Stratix10 will have an
additional reset signal, referred to as the OCP.
Add code to get the reset property from the device tree for deassert and
assert.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The registers for AXI DMAC are detailed at:
https://wiki.analog.com/resources/fpga/docs/axi_dmac#register_map
This change adds regmap support for these registers, in case some wants to
have a more direct access to them via this interface.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
[vkoul: fixed code style issue]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a partial transfer is received, the driver should not submit any more
segments to the hardware, as they will be ignored/unused until a new
transfer start operation is done.
This change implements this by adding a new flag on the AXI DMAC
descriptor. This flags is set to true, if there was a partial transfer in
a previously completed segment. When that flag is true, the TLAST flag is
added to the to the submitted segment, signaling the controller to stop
receiving more segments.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Starting with version 4.2.a, the AXI DMAC controller can report partial
transfers that have been issued.
This change implements computing DMA residue information for transfers,
based on that reported information.
The way this is done, is to dequeue the partial transfers from the FIFO of
partial transfers, store the partial length to the correct segment &
descriptor, and compute the residue before submitting the DMA cookie to the
DMA framework.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This allows each virtual channel to store information about each transfer
that completed, i.e. which transfer succeeded (or which failed) and if
there was any residue data on each (completed) transfer.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the
variables that were saving them as they were never even being used once
set.
Cc: Sinan Kaya <okaya@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sinan Kaya <okaya@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Sudeep Dutt <sudeep.dutt@intel.com>
Cc: Ashutosh Dixit <ashutosh.dixit@intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the
variable that was saving it as it was never even being used once set.
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to check the return value of debugfs_create_file(), so no need
to provide a fake "cast away" of the return value either.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Also, because there is no need to save the file dentry, remove the
variable that was saving it as it was never even being used once set.
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
No need to check the return value of debugfs_create_file(), so no need
to provide a fake "cast away" of the return value either.
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: dmaengine@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
If CONFIG_PCI_MSI is not set, building with CONFIG_DW_EDMA
fails:
drivers/dma/dw-edma/dw-edma-core.c: In function dw_edma_irq_request:
drivers/dma/dw-edma/dw-edma-core.c:784:21: error: implicit declaration of function pci_irq_vector; did you mean rcu_irq_enter? [-Werror=implicit-function-declaration]
err = request_irq(pci_irq_vector(to_pci_dev(dev), 0),
^~~~~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: e63d79d1ff ("dmaengine: Add Synopsys eDMA IP core driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The change replaces the old license information in the comment header with
the new SPDX license specifier.
As well as bumping the year range from 2013-2015 to 2013-2019.
The latter also reflects recent changes that were added to the driver.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Synopsys eDMA IP is normally distributed along with Synopsys PCIe
EndPoint IP (depends of the use and licensing agreement).
This IP requires some basic configurations, such as:
- eDMA registers BAR
- eDMA registers offset
- eDMA registers size
- eDMA linked list memory BAR
- eDMA linked list memory offset
- eDMA linked list memory size
- eDMA data memory BAR
- eDMA data memory offset
- eDMA data memory size
- eDMA version
- eDMA mode
- IRQs available for eDMA
As a working example, PCIe glue-logic will attach to a Synopsys PCIe
EndPoint IP prototype kit (Vendor ID = 0x16c3, Device ID = 0xedda),
which has built-in an eDMA IP with this default configuration:
- eDMA registers BAR = 0
- eDMA registers offset = 0x00001000 (4 Kbytes)
- eDMA registers size = 0x00002000 (8 Kbytes)
- eDMA linked list memory BAR = 2
- eDMA linked list memory offset = 0x00000000 (0 Kbytes)
- eDMA linked list memory size = 0x00800000 (8 Mbytes)
- eDMA data memory BAR = 2
- eDMA data memory offset = 0x00800000 (8 Mbytes)
- eDMA data memory size = 0x03800000 (56 Mbytes)
- eDMA version = 0
- eDMA mode = EDMA_MODE_UNROLL
- IRQs = 1
This driver can be compile as built-in or external module in kernel.
To enable this driver just select DW_EDMA_PCIE option in kernel
configuration, however it requires and selects automatically DW_EDMA
option too.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the eDMA IP version 0 driver for both register maps (legacy
and unroll).
The legacy register mapping was the initial implementation, which consisted
in having all registers belonging to channels multiplexed, which could be
change anytime (which could led a race-condition) by view port register
(access to only one channel available each time).
This register mapping is not very effective and efficient in a multithread
environment, which has led to the development of unroll registers mapping,
which consists of having all channels registers accessible any time by
spreading all channels registers by an offset between them.
This version supports a maximum of 16 independent channels (8 write +
8 read), which can run simultaneously.
Implements a scatter-gather transfer through a linked list, where the size
of linked list depends on the allocated memory divided equally among all
channels.
Each linked list descriptor can transfer from 1 byte to 4 Gbytes and is
alignmented to DWORD.
Both SAR (Source Address Register) and DAR (Destination Address Register)
are alignmented to byte.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Synopsys PCIe Endpoint eDMA IP core driver to kernel.
This IP is generally distributed with Synopsys PCIe Endpoint IP (depends
of the use and licensing agreement).
This core driver, initializes and configures the eDMA IP using vma-helpers
functions and dma-engine subsystem.
This driver can be compile as built-in or external module in kernel.
To enable this driver just select DW_EDMA option in kernel configuration,
however it requires and selects automatically DMA_ENGINE and
DMA_VIRTUAL_CHANNELS option too.
In order to transfer data from point A to B as fast as possible this IP
requires a dedicated memory space containing linked list of elements.
All elements of this linked list are continuous and each one describes a
data transfer (source and destination addresses, length and a control
variable).
For the sake of simplicity, lets assume a memory space for channel write
0 which allows about 42 elements.
+---------+
| Desc #0 |-+
+---------+ |
V
+----------+
| Chunk #0 |-+
| CB = 1 | | +----------+ +-----+ +-----------+ +-----+
+----------+ +->| Burst #0 |->| ... |->| Burst #41 |->| llp |
| +----------+ +-----+ +-----------+ +-----+
V
+----------+
| Chunk #1 |-+
| CB = 0 | | +-----------+ +-----+ +-----------+ +-----+
+----------+ +->| Burst #42 |->| ... |->| Burst #83 |->| llp |
| +-----------+ +-----+ +-----------+ +-----+
V
+----------+
| Chunk #2 |-+
| CB = 1 | | +-----------+ +-----+ +------------+ +-----+
+----------+ +->| Burst #84 |->| ... |->| Burst #125 |->| llp |
| +-----------+ +-----+ +------------+ +-----+
V
+----------+
| Chunk #3 |-+
| CB = 0 | | +------------+ +-----+ +------------+ +-----+
+----------+ +->| Burst #126 |->| ... |->| Burst #129 |->| llp |
+------------+ +-----+ +------------+ +-----+
Legend:
- Linked list, also know as Chunk
- Linked list element*, also know as Burst *CB*, also know as Change Bit,
it's a control bit (and typically is toggled) that allows to easily
identify and differentiate between the current linked list and the
previous or the next one.
- LLP, is a special element that indicates the end of the linked list
element stream also informs that the next CB should be toggle
On every last Burst of the Chunk (Burst #41, Burst #83, Burst #125 or
even Burst #129) is set some flags on their control variable (RIE and
LIE bits) that will trigger the send of "done" interruption.
On the interruptions callback, is decided whether to recycle the linked
list memory space by writing a new set of Bursts elements (if still
exists Chunks to transfer) or is considered completed (if there is no
Chunks available to transfer).
On scatter-gather transfer mode, the client will submit a scatter-gather
list of n (on this case 130) elements, that will be divide in multiple
Chunks, each Chunk will have (on this case 42) a limited number of
Bursts and after transferring all Bursts, an interrupt will be
triggered, which will allow to recycle the all linked list dedicated
memory again with the new information relative to the next Chunk and
respective Burst associated and repeat the whole cycle again.
On cyclic transfer mode, the client will submit a buffer pointer, length
of it and number of repetitions, in this case each burst will correspond
directly to each repetition.
Each Burst can describes a data transfer from point A(source) to point
B(destination) with a length that can be from 1 byte up to 4 GB. Since
dedicated the memory space where the linked list will reside is limited,
the whole n burst elements will be organized in several Chunks, that
will be used later to recycle the dedicated memory space to initiate a
new sequence of data transfers.
The whole transfer is considered has completed when it was transferred
all bursts.
Currently this IP has a set well-known register map, which includes
support for legacy and unroll modes. Legacy mode is version of this
register map that has multiplexer register that allows to switch
registers between all write and read channels and the unroll modes
repeats all write and read channels registers with an offset between
them. This register map is called v0.
The IP team is creating a new register map more suitable to the latest
PCIe features, that very likely will change the map register, which this
version will be called v1. As soon as this new version is released by
the IP team the support for this version in be included on this driver.
According to the logic, patches 1, 2 and 3 should be squashed into 1
unique patch, but for the sake of simplicity of review, it was divided
in this 3 patches files.
Signed-off-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPuGTg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykBvQCg2SG+HmDH+tlwKLT/q7jZcLMPQigAoMpt9Uuy
sxVEiFZo8ZU9v1IoRb1I
=qU++
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Another round of SPDX header file fixes for 5.2-rc4
These are all more "GPL-2.0-or-later" or "GPL-2.0-only" tags being
added, based on the text in the files. We are slowly chipping away at
the 700+ different ways people tried to write the license text. All of
these were reviewed on the spdx mailing list by a number of different
people.
We now have over 60% of the kernel files covered with SPDX tags:
$ ./scripts/spdxcheck.py -v 2>&1 | grep Files
Files checked: 64533
Files with SPDX: 40392
Files with errors: 0
I think the majority of the "easy" fixups are now done, it's now the
start of the longer-tail of crazy variants to wade through"
* tag 'spdx-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (159 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 450
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 449
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 448
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 446
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 445
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 444
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 443
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 442
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 441
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 440
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 438
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 437
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 436
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 435
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 434
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 433
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 432
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 431
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 430
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 429
...
The fixes for this round are in drivers:
- jz4780 transfer fix for acking descriptors early
- fsl-qdma: clean registers on error
- dw-axi-dmac: null pointer dereference fix
- mediatek-cqdma: fix sleeping in atomic context
- tegra210-adma: fix bunch os issues like crashing in driver
probe, channel FIFO configuration etc.
- sprd: Fixes for possible crash on descriptor status, block
length overflow. For 2-stage transfer fix incorrect start,
configuration and interrupt handling.
-----BEGIN PGP SIGNATURE-----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=Ca0d
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-5.2-rc4' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
- jz4780 transfer fix for acking descriptors early
- fsl-qdma: clean registers on error
- dw-axi-dmac: null pointer dereference fix
- mediatek-cqdma: fix sleeping in atomic context
- tegra210-adma: fix bunch os issues like crashing in driver probe,
channel FIFO configuration etc.
- sprd: Fixes for possible crash on descriptor status, block length
overflow. For 2-stage transfer fix incorrect start, configuration and
interrupt handling.
* tag 'dmaengine-fix-5.2-rc4' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sprd: Add interrupt support for 2-stage transfer
dmaengine: sprd: Fix the right place to configure 2-stage transfer
dmaengine: sprd: Fix block length overflow
dmaengine: sprd: Fix the incorrect start for 2-stage destination channels
dmaengine: sprd: Add validation of current descriptor in irq handler
dmaengine: sprd: Fix the possible crash when getting descriptor status
dmaengine: tegra210-adma: Fix spelling
dmaengine: tegra210-adma: Fix channel FIFO configuration
dmaengine: tegra210-adma: Fix crash during probe
dmaengine: mediatek-cqdma: sleeping in atomic context
dmaengine: dw-axi-dmac: fix null dereference when pointer first is null
dmaengine: fsl-qdma: Add improvement
dmaengine: jz4780: Fix transfers being ACKed too soon
Add 8250 UART APDMA to support MediaTek UART. If MediaTek UART is
enabled by SERIAL_8250_MT6577, and we can enable this driver to offload
the UART device moving bytes.
Signed-off-by: Long Cheng <long.cheng@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 101 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190113.822954939@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope [that] it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 57 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.515993066@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details the full gnu general public license is included in
this distribution in the file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 39 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.397680977@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H6 DMA has more than 32 supported DRQs, which means that configuration
register is slightly rearranged. It also needs additional clock to be
enabled.
Add support for it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
H6 DMA has mode fields in different position than any other currently
supported DMA controller.
Add a quirk for that.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
H6 DMA has more than 32 possible DRQs. That means that current maximum
of 31 DRQs is not enough anymore.
Add a quirk which will set source and destination DRQ number.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
H6 DMA controller needs additional mbus clock to be enabled.
Add a quirk for it and handle it accordingly.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Apparently driver was never tested with DMA_PREP_INTERRUPT flag being
unset since it completely disables interrupt handling instead of skipping
the callbacks invocations, hence putting channel into unusable state.
The flag is always set by all of kernel drivers that use APB DMA, so let's
error out in otherwise case for consistency. It won't be difficult to
support that case properly if ever will be needed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When an error occurs we should clean the error register then to return
Signed-off-by: Peng Ma <peng.ma@nxp.com>
[vkoul: change patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
CMD of Source/Destination descriptor format should be lower of
struct fsl_qdma_engine number data address.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details the full
gnu general public license is in this distribution in the file
called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100843.594454135@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `copy_align` property is a generic property that describes alignment
for DMA memcpy & sg ops.
It serves mostly an informational purpose, and can be used in DMA tests, to
pass the info to know what alignment to expect.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Starting with version 4.1.a the AXI-DMAC is capable of reporting the
required length alignment.
The LSBs that are required to be set for alignment will always read back as
set from the transfer length register. It is not possible to clear them by
writing a 0. This means the driver can discover the length alignment
requirement by writing 0 to that register and reading back the value.
Since the DMA will support length alignment requirements that are different
from the address alignment requirement track both of them independently.
For older versions of the peripheral assume that the length alignment
requirement is equal to the address alignment requirement.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Let the DMA engine core do the device node validation instead of drivers.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When user try to request one DMA channel by __dma_request_channel(), it won't
validate if it is the correct DMA device to request, that will lead each DMA
engine driver to validate the correct device node in their filter function
if it is necessary.
Thus we can add the matching device node validation in the DMA engine core,
to remove all of device node validation in the drivers.
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 1 normalized pattern(s):
this is free software you can redistribute it and or modify it under
the terms of the gnu general public license as published by the free
software foundation either version 2 of the license or at your
option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 14 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170857.915677517@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We get a compiler warn about variable ‘tail_desc’ set but not used
drivers/dma/xilinx/xilinx_dma.c:1102:42: warning:
variable ‘tail_desc’ set but not used [-Wunused-but-set-variable]
struct xilinx_dma_tx_descriptor *desc, *tail_desc;
So remove it.
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For 2-stage transfer, some users like Audio still need transaction interrupt
to notify when the 2-stage transfer is completed. Thus we should enable
2-stage transfer interrupt to support this feature.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Move the 2-stage configuration before configuring the link-list mode,
since we will use some 2-stage configuration to fill the link-list
configuration.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The maximum value of block length is 0xffff, so if the configured transfer length
is more than 0xffff, that will cause block length overflow to lead a configuration
error.
Thus we can set block length as the maximum burst length to avoid this issue, since
the maximum burst length will not be a big value which is more than 0xffff.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The 2-stage destination channel will be triggered by source channel
automatically, which means we should not trigger it by software request.
Signed-off-by: Eric Long <eric.long@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When user terminates one DMA channel to free all its descriptors, but
at the same time one transaction interrupt was triggered possibly, now
we should not handle this interrupt by validating if the 'schan->cur_desc'
was set as NULL to avoid crashing the kernel.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We will get a NULL virtual descriptor by vchan_find_desc() when the descriptor
has been submitted, that will crash the kernel when getting the descriptor
status.
In this case, since the descriptor has been submitted to process, but it
is not completed now, which means the descriptor is listed into the
'vc->desc_submitted' list now. So we can not get current processing descriptor
by vchan_find_desc(), but the pointer 'schan->cur_desc' will point to the
current processing descriptor, then we can use 'schan->cur_desc' to get
current processing descriptor's status to avoid this issue.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or any
later version this program is distributed in the hope that it will
be useful but without any warranty without even the implied warranty
of merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 50 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.917228456@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 4 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154042.707528683@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details the full
gnu general public license is included in this distribution in the
file called copying
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 9 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.244154651@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under gplv2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 118 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154040.961286471@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ded1f3db4c ("dmaengine: tegra210-adma: prepare for supporting
newer Tegra chips") removed the default settings DMA channel RX and TX
FIFO sizes and this is breaking DMA transfers. The intention was to
move the default settings to the chip specific data structure because
this commit was preparing for adding support for Tegra186 where the
fields for the FIFO CTRL register are slightly different.
Fix the configuration of the FIFO sizes by adding default values for
the FIFO CTRL register for both Tegra210 and Tegra186 and store the
values in the chip specific structure.
Fixes: ded1f3db4c ("dmaengine: tegra210-adma: prepare for supporting newer Tegra chips")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f33e7bb3eb ("dmaengine: tegra210-adma: restore channel status")
added support to save and restore the DMA channel registers when runtime
suspending the ADMA. This change is causing the kernel to crash when
probing the ADMA, if the device is probed deferred when looking up the
channel interrupts. The crash occurs because not all of the channel base
addresses have been setup at this point and in the clean-up path of the
probe, pm_runtime_suspend() is called invoking its callback which
expects all the channel base addresses to be initialised.
Although this could be fixed by simply checking for a NULL address, on
further review of the driver it seems more appropriate that we only call
pm_runtime_get_sync() after all the channel interrupts and base
addresses have been configured. Therefore, fix this crash by moving the
calls to pm_runtime_enable(), pm_runtime_get_sync() and
tegra_adma_init() after the DMA channels have been initialised.
Fixes: f33e7bb3eb ("dmaengine: tegra210-adma: restore channel status")
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The mtk_cqdma_poll_engine_done() function takes a true/false parameter
where true means it's called from atomic context. There are a couple
places where it was set to false but it's actually in atomic context
so it should be true.
All the callers for mtk_cqdma_hard_reset() are holding a spin_lock and
in mtk_cqdma_free_chan_resources() we take a spin_lock before calling
the mtk_cqdma_poll_engine_done() function.
Fixes: b1f01e48df ("dmaengine: mediatek: Add MediaTek Command-Queue DMA controller for MT6765 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In the unlikely event that axi_desc_get returns a null desc in the
very first iteration of the while-loop the error exit path ends
up calling axi_desc_put on a null pointer 'first' and this causes
a null pointer dereference. Fix this by adding a null check on
pointer 'first' before calling axi_desc_put.
Addresses-Coverity: ("Explicit null dereference")
Fixes: 1fe20f1b84 ("dmaengine: Introduce DW AXI DMAC driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AXI-DMAC supports different types of interface for the data source and
destination ports. Typically one of those ports is a memory-mapped
interface while the other is some kind of streaming interface.
The information about which kind of interface is used for each port is
encoded in the devicetree.
It is also possible in the driver to detect whether a port supports
memory-mapped transfers or not. For streaming interfaces the address
register is read-only and will always return 0. So in order to check if a
port supports memory-mapped transfers write a non-zero value to the
corresponding address register and check that the value read-back is still
non zero.
This allows to detect mismatches between the devicetree description and the
actual hardware configuration.
Unfortunately it is not possible to autodetect the interface types since
there is no method to distinguish between the different streaming ports. So
the best thing that can be done is to error out when a memory mapped port
is described in the devicetree but none is detected in the hardware.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The TLAST flag is used by the DMAC HDL controller to signal to the
controller that the following segment (to be submitted) is the last one (in
a series of segments).
A receiver DMA (typically another DMAC) can read this parameter (from the
transfer), and terminate the transfer earlier. A typical use-case for this,
is when the receiver expects a certain amount of segments, but for some
reason (e.g. an ADC capture which can have an unknown number of digital
samples) the number of actual segments is smaller. The receiver would read
this flag, and then the DMAC would finish.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The DMAC HDL core supports interleaved & cyclic transfers.
An example use-case for this mode is when the controller is used as a
video DMA.
This change sets the `cyclic` field to true, so that when the IRQ comes and
the `axi_dmac_transfer_done()` callback is called (from the interrupt
handler) the proper `vchan_cyclic_callback()` is called. This way the
DMAEngine framework will process data correctly for interleaved + cyclic
transfers.
This doesn't fix anything. It's an enhancement to the driver.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit c6504be539 ("dmaengine: stm32-dma: Fix unsigned variable compared
with zero") duplicated the call to platform_get_irq.
So remove the first call to platform_get_irq.
Fixes: c6504be539 ("dmaengine: stm32-dma: Fix unsigned variable compared with zero")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When an error occurs we should clean the error register then to return
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When a multi-descriptor DMA transfer is in progress, the "IRQ pending"
flag will apparently be set for that channel as soon as the last
descriptor loads, way before the IRQ actually happens. This behaviour
has been observed on the JZ4725B, but maybe other SoCs are affected.
In the case where another DMA transfer is running into completion on a
separate channel, the IRQ handler would then run the completion handler
for our previous channel even if the transfer didn't actually finish.
Fix this by checking in the completion handler that we're indeed done;
if not the interrupted DMA transfer will simply be resumed.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Use SPDX license notifier instead of plain text in the header.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
SUDMAC driver was introduced in v3.10 but was never integrated for use
by any platform. As it is unused remove it.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and
support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips
and support for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma,
rcar-dmac, stm32-dma etc
- dev_get_drvdata() updates on few drivers
-----BEGIN PGP SIGNATURE-----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=JDU6
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine updates from Vinod Koul:
- Updates to stm32 dma residue calculations
- Interleave dma capability to axi-dmac and support for ZynqMP arch
- Rework of channel assignment for rcar dma
- Debugfs for pl330 driver
- Support for Tegra186/Tegra194, refactoring for new chips and support
for pause/resume
- Updates to axi-dmac, bcm2835, fsl-edma, idma64, imx-sdma, rcar-dmac,
stm32-dma etc
- dev_get_drvdata() updates on few drivers
* tag 'dmaengine-5.2-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (34 commits)
dmaengine: tegra210-adma: restore channel status
dmaengine: tegra210-dma: free dma controller in remove()
dmaengine: tegra210-adma: add pause/resume support
dmaengine: tegra210-adma: add support for Tegra186/Tegra194
Documentation: DT: Add compatibility binding for Tegra186
dmaengine: tegra210-adma: prepare for supporting newer Tegra chips
dmaengine: at_xdmac: remove a stray bottom half unlock
dmaengine: fsl-edma: Adjust indentation
dmaengine: fsl-edma: Fix typo in Vybrid name
dmaengine: stm32-dma: fix residue calculation in stm32-dma
dmaengine: nbpfaxi: Use dev_get_drvdata()
dmaengine: bcm-sba-raid: Use dev_get_drvdata()
dmaengine: stm32-dma: Fix unsigned variable compared with zero
dmaengine: stm32-dma: use platform_get_irq()
dmaengine: rcar-dmac: Update copyright information
dmaengine: imx-sdma: Only check ratio on parts that support 1:1
dmaengine: xgene-dma: fix spelling mistake "descripto" -> "descriptor"
dmaengine: idma64: Move driver name to the header
dmaengine: bcm2835: Drop duplicate capability setting.
dmaengine: pl330: _stop: clear interrupt status
...
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAlzMFaUACgkQt6xw3ITB
YzRICQgAiv7wF/yIbBhDOmCNCAKDO59chvFQWxXWdGk/aAB56kwKAMXJgLOvlMG/
VRuuLyParTFQETC3jaxKgnO/1hb+PZLDt2Q2KqixtjIzBypKUPWvK2sf6THhSRF1
GK0DBVUd1rCrWrR815+SPb8el4xXtdBzvAVB+Fx35PXVNpdRdqCkK+EQ6UnXGokm
rXXHbnfsnquBDtmb4CR4r2beH+aNElXbdt0Kj8VcE5J7f7jTdW3z6Q9WFRvdKmK7
yrsxXXB2w/EsWXOwFp0SLTV5+fgeGgTvv8uLjDw+SG6t0E0PebxjNAflT7dPrbYL
WecjKC9WqBxrGY+4ew6YJP70ijLBCw==
=aC8m
-----END PGP SIGNATURE-----
Merge tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull mmiowb removal from Will Deacon:
"Remove Mysterious Macro Intended to Obscure Weird Behaviours (mmiowb())
Remove mmiowb() from the kernel memory barrier API and instead, for
architectures that need it, hide the barrier inside spin_unlock() when
MMIO has been performed inside the critical section.
The only relatively recent changes have been addressing review
comments on the documentation, which is in a much better shape thanks
to the efforts of Ben and Ingo.
I was initially planning to split this into two pull requests so that
you could run the coccinelle script yourself, however it's been plain
sailing in linux-next so I've just included the whole lot here to keep
things simple"
* tag 'arm64-mmiowb' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (23 commits)
docs/memory-barriers.txt: Update I/O section to be clearer about CPU vs thread
docs/memory-barriers.txt: Fix style, spacing and grammar in I/O section
arch: Remove dummy mmiowb() definitions from arch code
net/ethernet/silan/sc92031: Remove stale comment about mmiowb()
i40iw: Redefine i40iw_mmiowb() to do nothing
scsi/qla1280: Remove stale comment about mmiowb()
drivers: Remove explicit invocations of mmiowb()
drivers: Remove useless trailing comments from mmiowb() invocations
Documentation: Kill all references to mmiowb()
riscv/mmiowb: Hook up mmwiob() implementation to asm-generic code
powerpc/mmiowb: Hook up mmwiob() implementation to asm-generic code
ia64/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
mips/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
sh/mmiowb: Add unconditional mmiowb() to arch_spin_unlock()
m68k/io: Remove useless definition of mmiowb()
nds32/io: Remove useless definition of mmiowb()
x86/io: Remove useless definition of mmiowb()
arm64/io: Remove useless definition of mmiowb()
ARM/io: Remove useless definition of mmiowb()
mmiowb: Hook up mmiowb helpers to spinlocks and generic I/O accessors
...
Status of ADMA channel registers is not saved and restored during system
suspend. During active playback if system enters suspend, this results in
wrong state of channel registers during system resume and playback fails
to resume properly. Fix this by saving following channel registers in
runtime suspend and restore during runtime resume.
* ADMA_CH_LOWER_SRC_ADDR
* ADMA_CH_LOWER_TRG_ADDR
* ADMA_CH_FIFO_CTRL
* ADMA_CH_CONFIG
* ADMA_CH_CTRL
* ADMA_CH_CMD
* ADMA_CH_TC
Runtime PM calls will be inovked during system resume path if a playback
or capture needs to be resumed. Hence above changes work fine for system
suspend case.
Fixes: f46b195799 ("dmaengine: tegra-adma: Add support for Tegra210 ADMA")
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
During an audio playback session it is observed that, audio goes off after
few seconds of continuous pause and play. No audio is heard even when the
playback is resumed.
The reason for above is, currently ADMA driver does not handle DMA_PAUSE/
DMA_RESUME and relevant callbacks for dma_device are not implemented. This
patch implements device_pause and device_resume callbacks for the device.
During pause TRANSFER_PAUSE bit of dma channel control register is set and
the same is cleared during resume.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add Tegra186 specific macro defines and chip_data structure for chip
specific information. New compatibility is added to select relevant
chip details. There is no major change for Tegra194 and hence it can
use the same chip data.
The bits in the BURST_SIZE field of the ADMA CH_CONFIG register are
encoded differently on Tegra186 and Tegra194 compared with Tegra210.
On Tegra210 the bits are encoded as follows ...
1 = WORD_1
2 = WORDS_2
3 = WORDS_4
4 = WORDS_8
5 = WORDS_16
Where as on Tegra186 and Tegra194 the bits are encoded as ...
0 = WORD_1
1 = WORDS_2
2 = WORDS_3
3 = WORDS_4
4 = WORDS_5
...
15 = WORDS_16
Add helper functions for generating the correct burst size.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This is a preparatory patch to add support for Tegra186 and Tegra194 chips.
Following changes are necessary to make driver code generic.
* chip_data structure is enhanced to have chip specific details and
following are the additions to the structure
* Offset addresses for ADMA global and channel registers
* Offset values for Tx and Rx channel selection
* Maximum supported Tx and Rx channels
* Tx and Rx channel request mask
* ADMA channel register space size
* Make use of above chip_data to generalise the driver code
Support for Tegra186 and Tegra194 will be added in subsequent patches of
the series.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
We switched this code from spin_lock_bh() to vanilla spin_lock() but
there was one stray spin_unlock_bh() that was overlooked. This
patch converts it to spin_unlock() as well.
Fixes: d8570d018f ("dmaengine: at_xdmac: move spin_lock_bh to spin_lock in tasklet")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Fix indentation and remove unneeded space after 'return' keyword. This
fixes checkpatch warning:
WARNING: Statements should start on a tabstop
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In double buffer mode, during residue calculation, the DMA can
automatically switch to the next transfer. Indeed the CT bit that
gives position in the double buffer can has been updated by the
hardware, during calculation.
In this case the SxNDTR register value can not be trusted.
If a transition is detected we consider that the DMA has switched to
the beginning of next sg.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Commit f4fd2ec08f17: ("dmaengine: stm32-dma: use platform_get_irq()") used
unsigned variable irq to store the results and check later for negative
errors, so update the code to use signed variable for this
Fixes: f4fd2ec08f ("dmaengine: stm32-dma: use platform_get_irq()")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it was
not retrieved earlier.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On imx8mq B0 chip, AHB/SDMA clock ratio 2:1 can't be supported,
since SDMA clock ratio has to be increased to 250Mhz, AHB can't reach
to 500Mhz, so use 1:1 instead.
To limit this change to the imx8mq for now this patch also adds an
im8mq-sdma compatible string.
Signed-off-by: Angus Ainslie (Purism) <angus@akkea.ca>
Acked-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There is a spelling mistake in a chan_dbg message, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
There are two drivers that are relying on the iDMA 64-bit driver name
to match. Instead of duplicating string in both of them, dedicate
a header file and share it between users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This patch kill instructs the DMAC to immediately terminate
execution of a thread. and then clear the interrupt status,
at last, stop generating interrupts for DMA_SEV. to guarantee
the next dma start is clean. otherwise, one interrupt maybe leave
to next start and make some mistake.
we can reporduce the problem as follows:
DMASEV: modify the event-interrupt resource, and if the INTEN sets
function as interrupt, the DMAC will set irq<event_num> HIGH to
generate interrupt. write INTCLR to clear interrupt.
DMA EXECUTING INSTRUCTS DMA TERMINATE
| |
| |
... _stop
| |
| spin_lock_irqsave
DMASEV |
| |
| mask INTEN
| |
| DMAKILL
| |
| spin_unlock_irqrestore
in above case, a interrupt was left, and if we unmask INTEN, the DMAC
will set irq<event_num> HIGH to generate interrupt.
to fix this, do as follows:
DMA EXECUTING INSTRUCTS DMA TERMINATE
| |
| |
... _stop
| |
| spin_lock_irqsave
DMASEV |
| |
| DMAKILL
| |
| clear INTCLR
| mask INTEN
| |
| spin_unlock_irqrestore
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Since device_prep_interleaved_dma() is already implemented, the
DMA_INTERLEAVE capability should be set.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
In 2D transfers (for the AXI DMAC), the number of frames (numf) represents
Y_LENGTH, and the length of a frame is X_LENGTH. 2D transfers are useful
for video transfers where screen resolutions ( X * Y ) are typically
aligned for X, but not for Y.
There is no requirement for Y_LENGTH to be aligned to the bus-width (or
anything), and this is also true for AXI DMAC.
Checking the Y_LENGTH for alignment causes false errors when initiating DMA
transfers. This change fixes this by checking only that the Y_LENGTH is
non-zero.
Fixes: 0e3b67b348 ("dmaengine: Add support for the Analog Devices AXI-DMAC DMA controller")
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Some synthesis time configuration parameters of the DMA controller can be
inferred from the hardware itself.
Use this information as it is more reliably than the information specified
in the devicetree which might be outdated if the HDL project got changed.
Deprecate the devicetree properties that can be inferred from the hardware
itself.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The tx_status poll in the rcar_dmac driver reads the status register
which indicates which chunk is busy (DMACHCRB). Afterwards the point
inside the chunk is read from DMATCRB. It is possible that the chunk
has changed between the two reads. The result is a non-monotonous
increase of the residue. Fix this by introducing a 'safe read' logic.
Fixes: 73a47bd0da ("dmaengine: rcar-dmac: use TCRB instead of TCR for residue")
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: <stable@vger.kernel.org> # v4.16+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Having a cyclic DMA, a residue 0 is not an indication of a completed
DMA. In case of cyclic DMA make sure that dma_set_residue() is called
and with this a residue of 0 is forwarded correctly to the caller.
Fixes: 3544d28788 ("dmaengine: rcar-dmac: use result of updated get_residue in tx_status")
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Achim Dahlhoff <Achim.Dahlhoff@de.bosch.com>
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Yao Lihua <ylhuajnu@outlook.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The commit af19b7ce76 ("mmc: bcm2835: Avoid possible races on
data requests") introduces a possible circular locking dependency,
which is triggered by swapping to the sdhost interface.
So instead of reintroduce the race condition again, we could also
avoid this situation by using GFP_NOWAIT for the allocation of the
DMA buffer descriptors.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: af19b7ce76 ("mmc: bcm2835: Avoid possible races on data requests")
Link: http://lists.infradead.org/pipermail/linux-rpi-kernel/2019-March/008615.html
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The overflow error flag (ROI: Request Overflow Error) is only relevant
for the case when the channel handles a peripheral synchronized transfer.
Not in the case of memory to memory transfer where there is no hardware
request signal.
Remove the use of this interrupt source in such a case. It's based on
the first descriptor which holds the configuration for the whole
linked list transfer.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Complement the identification of errors with stopping the channel and
dumping the descriptor that led to the error case.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Even if this case shouldn't happen when controller is properly programmed,
it's still better to avoid dumping a kernel Oops for this.
As the sequence may happen only for debugging purposes, log the error and
just finish the tasklet call.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Krzysztof Kozlowski