It'll be easier to add other board specific code.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6qsabrelite has a sst25vf016b SPI NOR flash connected to eCSPI1.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Do not hardcode the local mac address.
Let bootloader retrieve it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It has been pointed out by device tree maintainer for several times
that the generic names 'serial' and 'ethernet' should be used for
those devices per ePAPR. Renames imx uart and fec device tree nodes
to stop them being bad examples.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Remove bootargs field as this information is retrieved from the bootloader.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add anatop regulators to imx6q.dtsi for all imx6q platforms.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Signed-off-by: Richard Zhao <richard.zhao@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch also adds the SPDIF baud clock mux and dividers.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This also changes the DMA clkdev lookup to use the imx-dma driver name
and "ahb" as connection ID to request the hclk dma clock.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This gate consists of two bits:
0b00: clk disabled
0b01: clk enabled in run mode and disabled in sleep mode
0b11: clk enabled
Currently only disabled and enabled are supported. As it's unlikely
that we find something like this in another SoC create a i.MX specific
clk helper for this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pllv1 is found on i.MX1, i.M25, i.MX27, i.MX31 and i.MX35.
Currently only reading the rate is supported.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
- Add necessary #ifdefs for CONFIG_COMMON_CLOCK
- Add a global spinlock to protect the CCM registers
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Instead of having a cpu_is_* in each ccm register access it
is more efficient to make it a variable.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
We used to pass the timer clock directly to mxc_timer_init. We
should instead request the correct clock. This is an intermediate
step: For now we request the clock in the timer code when NULL
is passed as clock.
Also, the gpt on some i.MX have an additional ipg clock which can
be gated. Request and enable this.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Every i.MX ehci controller has a ahb and a ipg clock, so request
it on every SoC. Do not make a special case for the usb phy clock
of the i.MX51. Just request it but make it optional.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the current i.MX clock support groups together unrelated clocks
to a single clock which is then used by the driver. This can't
be accomplished with the generic clock framework so we instead
request the individual clocks in the driver. For i.MX there are
generally three different clocks:
ipg: bus clock (needed to access registers)
ahb: dma relevant clock, sometimes referred to as hclk in the datasheet
per: bit clock, pixel clock
This patch changes the driver to request the individual clocks.
Currently all clk_get will get the same clock until the SoCs
are converted to the generic clock framework
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Otherwise cpu_active_mask will not set, which lead to other issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major fixes here are:
* Build fix for omap_hsmmc with OF against 3.4-rc1.
* Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3,
which broke hotplug card detection when UNSAFE_RESUME is set.
* Fix a race condition in omap_hsmmc with runtime PM.
* Fix two libertas SDIO-powered-resume regressions.
Also small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Zl8K
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gHlK
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
pfm_vm_munmap() is simply vm_munmap() and pfm_remove_smpl_mapping()
always get current as the first argument.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... since exit_mmap() is coming and it will munmap() everything anyway.
In all other cases aio_free_ring() has ctx->mm == current->mm; moreover,
all other callers of vm_munmap() have mm == current->mm, so this will
allow us to get rid of mm argument of vm_munmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Richard Zhao