A respun version of the merges for the pull request previously sent with
a few additional fixes. The last two merges were fixed up by hand since
the branches have moved on and currently have the prior merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller.
- Fix duplicate device registration for ACPI.
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends).
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer.
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CbUw
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A respun version of the merges for the pull request previously sent
with a few additional fixes. The last two merges were fixed up by
hand since the branches have moved on and currently have the prior
merge in them.
Quite a busy release for the SPI subsystem, mostly in cleanups big and
small scattered through the stack rather than anything else:
- New driver for the Broadcom BC63xx HSSPI controller
- Fix duplicate device registration for ACPI
- Conversion of s3c64xx to DMAEngine (this pulls in platform and DMA
changes upon which the transiton depends)
- Some small optimisations to reduce the amount of time we hold locks
in the datapath, eliminate some redundant checks and the size of a
spi_transfer
- Lots of fixes, cleanups and general enhancements to drivers,
especially the rspi and Atmel drivers"
* tag 'spi-v3.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (112 commits)
spi: core: Fix transfer failure when master->transfer_one returns positive value
spi: Correct set_cs() documentation
spi: Clarify transfer_one() w.r.t. spi_finalize_current_transfer()
spi: Spelling s/finised/finished/
spi: sc18is602: Convert to use bits_per_word_mask
spi: Remove duplicate code to set default bits_per_word setting
spi/pxa2xx: fix compilation warning when !CONFIG_PM_SLEEP
spi: clps711x: Add MODULE_ALIAS to support module auto-loading
spi: rspi: Add missing clk_disable() calls in error and cleanup paths
spi: rspi: Spelling s/transmition/transmission/
spi: rspi: Add support for specifying CPHA/CPOL
spi/pxa2xx: initialize DMA channels to -1 to prevent inadvertent match
spi: rspi: Add more QSPI register documentation
spi: rspi: Add more RSPI register documentation
spi: rspi: Remove dependency on DMAE for SHMOBILE
spi/s3c64xx: Correct indentation
spi: sh: Use spi_sh_clear_bit() instead of open-coded
spi: bitbang: Grammar s/make to make/to make/
spi: sh-hspi: Spelling s/recive/receive/
spi: core: Improve tx/rx_nbits check comments
...
This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep it
strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared with Mike
Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for multiplatform
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3CcT
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is the branch where we usually queue up cleanup efforts, moving
drivers out of the architecture directory, header file restructuring,
etc. Sometimes they tangle with new development so it's hard to keep
it strictly to cleanups.
Some of the things included in this branch are:
* Atmel SAMA5 conversion to common clock
* Reset framework conversion for tegra platforms
- Some of this depends on tegra clock driver reworks that are shared
with Mike Turquette's clk tree.
* Tegra DMA refactoring, which are shared branches with the DMA tree.
* Removal of some header files on exynos to prepare for
multiplatform"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: mvebu: move Armada 370/XP specific definitions to armada-370-xp.h
ARM: mvebu: remove prototypes of non-existing functions from common.h
ARM: mvebu: move ARMADA_XP_MAX_CPUS to armada-370-xp.h
serial: sh-sci: Rework baud rate calculation
serial: sh-sci: Compute overrun_bit without using baud rate algo
serial: sh-sci: Remove unused GPIO request code
serial: sh-sci: Move overrun_bit and error_mask fields out of pdata
serial: sh-sci: Support resources passed through platform resources
serial: sh-sci: Don't check IRQ in verify port operation
serial: sh-sci: Set the UPF_FIXED_PORT flag
serial: sh-sci: Remove duplicate interrupt check in verify port op
serial: sh-sci: Simplify baud rate calculation algorithms
serial: sh-sci: Remove baud rate calculation algorithm 5
serial: sh-sci: Sort headers alphabetically
ARM: EXYNOS: Kill exynos_pm_late_initcall()
ARM: EXYNOS: Consolidate selection of PM_GENERIC_DOMAINS for Exynos4
ARM: at91: switch Calao QIL-A9260 board to DT
clk: at91: fix pmc_clk_ids data type attriubte
PM / devfreq: use inclusion <mach/map.h> instead of <plat/map-s5p.h>
ARM: EXYNOS: remove <mach/regs-clock.h> for exynos
...
On ARM-based SHMOBILE, the rspi driver builds and works fine without the
DMA controller driver, hence relax the dependencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to force selection of TI EDMA DMA engine
driver when DaVinci SPI driver is selected. The driver
builds just fine even with CONFIG_TI_EDMA disabled.
Forcing this selection causes warnings of the sort:
warning: (ARCH_KEYSTONE && SPI_DAVINCI) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))
This reverts commit b5f1433059.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Tegra's clock driver now provides an implementation of the common
reset API (include/linux/reset.h). Use this instead of the old Tegra-
specific API; that will soon be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Add a driver for the High Speed SPI controller found on newer BCM63XX SoCs.
It does feature some new modes like 3-wire or dual spi, but neither of it
is currently implemented.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps increasing build testing coverage.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
The legacy S3C64xx DMA driver has been removed, DMA support on
S3C64xx is provided only by the generic PL08x driver.
This patch modifies the Kconfig entry of spi-s3c64xx driver, which
relies on availability of DMA, to always select the S3C64XX_PL080
symbol.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With support for amba-pl08x driver, on S3C64xx the generic DMA engine
API can be used instead of the private s3c-dma interface.
Signed-off-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace all symbols by simple dependency PLAT_SAMSUNG.
Signed-off-by: Mateusz Krawczuk <m.krawczuk@partner.samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The R8A7790 has QSPI module which is very similar to RSPI.
This patch adds into RSPI module together to supports QSPI module.
Signed-off-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@linaro.org>
- improve dependencies using COMPILE_TEST
- fix a typo
- drop platform_set_drvdata(pdev, NULL) in error path of probe
- make MODULE_LICENSE match the header
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The patch add basic support for the quad spi controller.
QSPI is a kind of spi module that allows single,
dual and quad read access to external spi devices. The module
has a memory mapped interface which provide direct interface
for accessing data form external spi devices.
The patch will configure controller clocks, device control
register and for defining low level transfer apis which
will be used by the spi framework to transfer data to
the slave spi device(flash in this case).
Test details:
-------------
Tested this on dra7 board.
Test1: Ran mtd_stesstest for 40000 iterations.
- All iterations went through without failure.
Test2: Use mtd utilities:
- flash_erase to erase the flash device
- mtd_debug read to read data back.
- mtd_debug write to write to the data flash.
diff between the write and read data shows zero.
Acked-by: Felipe Balbi<balbi@ti.com>
Reviewed-by: Felipe Balbi<balbi@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The serial peripheral interface (SPI) module implemented on Freescale Vybrid
platform provides a synchronous serial bus for communication between Vybrid
and the external peripheral device.
The SPI supports full-duplex, three-wire synchronous transfer, has TX/RX FIFO
with depth of four entries.
This driver is the SPI master mode driver and has been tested on Vybrid
VF610TWR board.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that DMA support has been added to the driver it needs the
architecture DMA driver to be built in order to link.
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable the build of drivers which don't have any real build time
dependency on their architecture or platform with COMPILE_TEST,
providing better build time coverage.
Signed-off-by: Mark Brown <broonie@linaro.org>
Keystone2 SOCs share the SPI IP block with DaVinci based SOCs. Update
the config bits so that its usable on Keystone2 based SOCs.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The filter function used by the rspi driver is part of the DMAE controller
driver so if the DMA controller driver is somehow disabled then the rspi
driver will fail to build.
Signed-off-by: Mark Brown <broonie@linaro.org>
New spi controller(version 3) is integrated into Blackfin
60x processor. Comparing to bf5xx spi controller, we support
32 bits word size and independent receive and transmit DMA
channels now. Also mode 0 and 2 (CPHA = 0) can get fully
supported becasue cs line may be controlled by the software.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.
This fixes all occurences that appear like common SiRF code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
A fairly quiet release for SPI, mainly driver work. A few highlights:
- Supports bits per word compatibility checking in the core.
- Allow use of the IP used in Freescale SPI controllers outside
Freescale SoCs.
- DMA support for the Atmel SPI driver.
- New drivers for the BCM2835 and Tegra114.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+Omc
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, mainly driver work. A few highlights:
- Supports bits per word compatibility checking in the core.
- Allow use of the IP used in Freescale SPI controllers outside
Freescale SoCs.
- DMA support for the Atmel SPI driver.
- New drivers for the BCM2835 and Tegra114"
* tag 'spi-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (68 commits)
spi-topcliff-pch: fix to use list_for_each_entry_safe() when delete list items
spi-topcliff-pch: missing platform_driver_unregister() on error in pch_spi_init()
ARM: dts: add pinctrl property for spi node for atmel SoC
ARM: dts: add spi nodes for the atmel boards
ARM: dts: add spi nodes for atmel SoC
ARM: at91: add clocks for spi dt entries
spi/spi-atmel: add dmaengine support
spi/spi-atmel: add flag to controller data for lock operations
spi/spi-atmel: add physical base address
spi/sirf: fix MODULE_DEVICE_TABLE
MAINTAINERS: Add git repository and update my address
spi/s3c64xx: Check for errors in dmaengine prepare_transfer()
spi/s3c64xx: Fix non-dmaengine usage
spi: omap2-mcspi: fix error return code in omap2_mcspi_probe()
spi/s3c64xx: let device core setup the default pin configuration
MAINTAINERS: Update Grant's email address and maintainership
spi: omap2-mcspi: Fix transfers if DMADEVICES is not set
spi: s3c64xx: move to generic dmaengine API
spi-gpio: init CS before spi_bitbang_setup()
spi: spi-mpc512x-psc: let transmiter/receiver enabled when in xfer loop
...
GENERIC_GPIO is now equivalent to GPIOLIB and features that depended on
GENERIC_GPIO can now depend on GPIOLIB to allow removal of this option.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Add SPI driver for NVIDIA's Tegra114 SPI controller. This controller
is different than the older SoCs SPI controller in internal design as
well as register interface.
This driver supports the:
- non DMA based transfer for smaller transfer i.e. less than FIFO depth.
- APB DMA based transfer for larger transfer i.e. more than FIFO depth.
- Clock gating through runtime PM callbacks.
- registration through DT only.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds support for the mostly register-compatible SPICTRL cores from the
GRLIB VHDL IP core library from Aeroflex Gaisler. They are normally running on
SPARC. A different entry in of_fsl_spi_match matches this core and indicates a
different hardware type that is used to set up different function pointers and
special cases.
The GRLIB core operates in cpu mode. The number of bits per word might be
limited. There might be native chipselects selected via a slave select
register. These differences to the FSL type cores, if present, are indicated by
a capabilities register. Other register and function differences exists but are
not relevant to the driver.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the spi-fsl-spi driver usable in CPU mode outside of an FSL_SOC and
even an powerpc environment by moving CPM mode functionality to a separate file
that is only compiled and linked in an FSL_SOC environment and adding some
ifdefs to hide types and functions or provide alternatives.
For devicetree probing a "clock-frequency" property is used for clock frequency
instead of calls to FSL_SOC-specific functions.
Acked-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The BCM2835 contains two forms of SPI master controller (one known
simply as SPI0, and the other known as the "Universal SPI Master", in
the auxilliary block) and one form of SPI slave controller. This patch
adds support for the SPI0 controller.
This driver is taken from Chris Boot's repository at
git://github.com/bootc/linux.git rpi-linear
as of commit 6de2905 "spi-bcm2708: fix printf with spurious %s".
In the first SPI-related commit there, Chris wrote:
Thanks to csoutreach / A Robinson for his driver which I used as an
inspiration. You can find his version here:
http://piface.openlx.org.uk/raspberry-pi-spi-kernel-driver-available-for
Changes made during upstreaming:
* Renamed bcm2708 to bcm2835 as per upstream naming for this SoC.
* Removed support for brcm,realtime property.
* Increased transfer timeout to 30 seconds.
* Return IRQ_NONE from the IRQ handler if no interrupt was handled.
* Disable TA (Transfer Active) and clear FIFOs on a transfer timeout.
* Wrote device tree binding documentation.
* Request unnamed clock rather than "sys_pclk"; the DT will provide the
correct clock.
* Assume that tfr->speed_hz and tfr->bits_per_word are always set in
bcm2835_spi_start_transfer(), bcm2835_spi_transfer_one(), so no need
to check spi->speed_hz or tft->bits_per_word.
* Re-ordered probe() to remove the need for temporary variables.
* Call clk_disable_unprepare() rather than just clk_unprepare() on probe()
failure.
* Don't use devm_request_irq(), to ensure that the IRQ doesn't fire after
we've torn down the device, but not unhooked the IRQ.
* Moved probe()'s call to clk_prepare_enable() so we can be sure the clock
is enabled if the IRQ handler fires immediately.
* Remove redundant checks from bcm2835_spi_check_transfer() and
bcm2835_spi_setup().
* Re-ordered IRQ handler to check for RXR before DONE. Added comments to
ISR.
* Removed empty prepare/unprepare implementations.
* Removed use of devinit/devexit.
* Added BCM2835_ prefix to defines.
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Intel Lynxpoint PCH Low Power Subsystem has two general purpose SPI
controllers that are LPSS_SSP compatible. These controllers are enumerated
from ACPI namespace with ACPI IDs INT33C0 and INT33C1.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To be able to use DMA with this driver on non-PXA platforms we implement
support for the generic DMA engine API. This lets user to use different DMA
engines with little or no modification to the driver.
Request lines and channel numbers can be passed to the driver from the
platform specific data.
The DMA engine implementation will be selected by default even on PXA
platform. User can select the legacy DMA API by enabling Kconfig option
CONFIG_SPI_PXA2XX_PXADMA.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The PXA SPI driver uses PXA platform specific private DMA implementation
which does not work on non-PXA platforms. In order to use this driver on
other platforms we break out the private DMA implementation into a separate
file that gets compiled only when CONFIG_SPI_PXA2XX_PXADMA is set. The DMA
functions are stubbed out if there is no DMA implementation selected (i.e
we are building on non-PXA platform).
While we are there we can kill the dummy DMA bits in pxa2xx_spi.h as they
are not needed anymore for CE4100.
Once this is done we can add the generic DMA engine support to the driver
that allows usage of any DMA controller that implements DMA engine API.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Lu Cao <lucao@marvell.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We are going to use it on 64-bit kernel on Intel Lynxpoint so make sure we
can build it into such kernel.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds