* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: mixart: range checking proc file
ALSA: hda - Fix a wrong array range check in patch_realtek.c
ALSA: ASoC: move dma_data from snd_soc_dai to snd_soc_pcm_stream
ALSA: hda - Enable amplifiers on Acer Inspire 6530G
ASoC: Only do WM8994 bias off transition from standby
ASoC: Don't use DCS_DATAPATH_BUSY for WM hubs devices
ASoC: Don't do runtime wm_hubs DC servo updates if using offset correction
ASoC: Support second DC servo readback method for wm_hubs
ASoC: Avoid wraparound in wm_hubs DC servo correction
ALSA: echoaudio - Eliminate use after free
ALSA: i2c: cleanup: change parameter to pointer
ALSA: hda - Add MSI blacklist for Aopen MZ915-M
ASoC: OMAP: Fix capture pointer handling for OMAP1510 to work correctly with recent ALSA PCM code
ALSA: hda - Update document about MSI and interrupts
ALSA: hda: Fix 0 dB offset for Lenovo Thinkpad models using AD1981
ALSA: hda - Add missing printk argument in previous patch
ASoC: Fix passing platform_data to ac97 bus users and fix a leak
ALSA: hda - Fix ADC/MUX assignment of ALC269 codec
ALSA: hda - Fix invalid bit values passed to snd_hda_codec_amp_stereo()
ASoC: wm8994: playback => capture
This fixes a memory corruption when ASoC devices are used in
full-duplex mode. Specifically for pxa-ssp code, where this pointer
is dynamically allocated for each direction and destroyed upon each
stream start.
All other platforms are fixed blindly, I couldn't even compile-test
them. Sorry for any breakage I may have caused.
[Note that this is a backported version for 2.6.34.
Upstream commit is fd23b7dee]
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Reported-by: Michael Hirsch <m.hirsch@raumfeld.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Sometimes after a suspend-resume cycle, the ALSA application
restarts the stream when resume fails and McASP fails to work
as the clock is not enabled. This patch corrects this bug.
Testes on TI DA850/OMAP-L138 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add clock enable and disable calls to resume and suspend respectively.
Also add a member to the audio device data structure which tracks the clock
status.
Tested on DA850/OMAP-L138 EVM. For the purpose of testing, the patches[1] which
add suspend-to-RAM support to DA850/OMAP-L138 SoC were applied.
[1] http://linux.davincidsp.com/pipermail/davinci-linux-open-source/
2009-November/016958.html
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use edma_pause and edma_resume to make missing dma_events
less likely. This may not be needed, but it looks better.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix underruns by using dma to copy 1st to sram
in a ping/pong buffer style and then copying from
the sram to the ASP. This also has the advantage
of tolerating very long interrupt latency on dma
completion.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename variable master_lch to asp_channel
Rename variable slave_lch to asp_link[0]
Rename local variables:
lch to link
count to asp_count
src to asp_src
dst to asp_dst
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow the left and right 16 bit samples to be shifted out as 1
32 bit sample.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove requirement that dma_params is 1st in the structures
davinci_audio_dev and davinci_mcbsp_dev.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DMA params for McASP with FIFO has been updated so that it works for
various FIFO levels. A member- 'fifo_level' has been added to the DMA
params data structure. The fifo_level can be adjusted by the tx[rx]_numevt
platform data. This is relevant only for DA8xx/OMAP-L1xx platforms. This
implementation has been tested for numevt values 1, 2, 4, 8.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McASP write FIFO registers should be modified for playback and read FIFO
registers for capture. Check the PCM mode before manipulating the
FIFO registers. Currently, irrespective of playback/capture both the
FIFOs are enabled or disbaled. This resulted in errors in audio loopback
mode.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch removes references to cpu_dai->dma_data.
It makes struct davinci_pcm_dma_params part of
struct davinci_mcbsp_dev or struct davinci_audio_dev.
It removes the unused name variable from davinci_pcm_dma_params.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When both playback and capture stream were open
davinci_i2s_hw_params was setting parameters for
the wrong stream. The fix for davinci_i2s_hw_params
is sufficient, but it looks like a race still happens
in davici_pcm_open. This patch also makes the race smaller
but the next patch provides a better fix.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: wm8753: fix mapping when MONOMIX is set to Stereo
ASoC: some minor changes for AD1836 and AD1938 codec drivers
ASoC: DaVinci: Fixes to McASP configuration
ASoC: Blackfin I2S: fix resuming when device hasn't been used
ASoC: Blackfin I2S: add lost platform_device parameter to resume function
ASoC: fix typos in Blackfin headers
ASoC: bf5xx-sport: the irq save/restore funcs take an unsigned long
ASoC: Blackfin AC97: add a few missing multichannel define handling
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (62 commits)
DaVinci: DM646x - platform changes for vpif capture and display drivers
davinci: DM355 - platform changes for vpfe capture
davinci: DM644x platform changes for vpfe capture
davinci: audio: move tlv320aic33 i2c setup into board files
DaVinci: EDMA: Adding 2 new APIs for allocating/freeing PARAMs
DaVinci: DM365: Adding entries for DM365 IRQ's
DaVinci: DM355: Adding PINMUX entries for DM355 Display
davinci: Handle pinmux conflict between mmc/sd and nor flash
davinci: Add NOR flash support for da850/omap-l138
davinci: Add NAND flash support for DA850/OMAP-L138
davinci: Add MMC/SD support for da850/omap-l138
davinci: Add platform support for da850/omap-l138 GLCD
davinci: Macro to convert GPIO signal to GPIO pin number
davinci: Audio support for DA850/OMAP-L138 EVM
davinci: Audio support for DA830 EVM
davinci: Correct the number of GPIO pins for da850/omap-l138
davinci: Configure MDIO pins for EMAC
DaVinci: DM365: Add Support for new Revision of silicon
DaVinci: DM365: Fix Compilation issue due to PINMUX entry
DaVinci: EDMA: Updating default queue handling
...
McASP register settings are not correct for DSP mode of operation.
There is a channel swap initally. This patch provides fixes to
the register values for proper working.
Tested on DA830/OMAP-L137 EVM, DM6467 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch enables tlv320aic3101 support on DM365 EVM and
it was tested on DM365 EVM rev c.
Note: this patch was created based on temp/asoc branch.
Signed-off-by: Miguel Aguilar <miguel.aguilar@ridgerun.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also, the codec setup data structure has to remain for successful
probe.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- restructure to support multiple channel controllers by using
additional struct resources for each CC
- interface changes visible to EDMA clients
Introduce macros to build IDs from controller and channel number,
and to extract them. Modify the edma_alloc_slot function to take an
extra argument for the controller.
Also update ASoC drivers to use API. ASoC changes
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
- Move queue related mappings to dm<soc>.c
EDMA in DM355 and DM644x has two transfer controllers while DM646x
has four transfer controllers. Moving the queue to tc mapping and
queue priority mapping to dm<soc>.c will be helpful to probe these
mappings from platform device so that the machine_is_* testing will
be avoided.
- add channel mapping logic
Channel mapping logic is introduced in dm646x EDMA. This implies
that there is no fixed association for a channel number to a
parameter entry number. In other words, using the DMA channel
mapping registers (DCHMAPn), a PaRAM entry can be mapped to any
channel. While in the case of dm644x and dm355 there is a fixed
mapping between the EDMA channel and Param entry number.
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Reviewed-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Fixup the device changes by modifying the files that we just removed the
explicit device creation from with i2c_register_board_info() until this
can be moved into the relevant board files.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tlv320aic3x driver managed its own i2c device, instead of an extant
one created by the board support code. Change the code to make it so that
the driver binds to an extant (in this case i2c) device.
Add explict tlv320aic33 as well as tlv320aic3x to the supported device
table and remove the old driver bindings from the users of this code.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is one instance of McASP on DA850/OMAP-L138 SoC. This is
connected to TLV320AIC3106 codec for audio playback and capture.
This patch adds audio support on this platform. Some of the
structure prefix names which are common for DA830/OMAP-L137 EVM and
DA850/OMAP-L138 EVM have been renamed to da8xx from da830.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The patch adds a DAI format: Codec bit clock master and frame sync slave,
to the driver.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On DA830/OMAP-L137 and DA850/OMAP-L138 SoCs, the McASP peripheral has FIFO
support. This FIFO provides additional data buffering. It also provides
tolerance to variation in host/DMA controller response times.
The read and write FIFO sizes are 256 bytes each. If FIFO is enabled,
the DMA events from McASP are sent to the FIFO which in turn sends DMA requests
to the host CPU according to the thresholds programmed.
More details of the FIFO operation can be found at
http://focus.ti.com/general/docs/lit/getliterature.tsp?literatureNumber=
sprufm1&fileType=pdf
This patch adds support for FIFO configuration. The platform data has a
version field which differentiates the McASP on different SoCs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for audio on DA830 EVM- here McASP1 is interfaced to
TLV320AIC3106 codec.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The dma setup code assumes that the buffer size is a multiple
of the period size.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
dai is a parameter to the functions, so use it instead of
looking it up.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
clock name strings are no longer passed on platform_data. Instead,
we rely entirely on struct device and clkdev to find the right clock.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Update the dma link with correct data as soon as
the master channel has copied it. Otherwise, the
1st period will play twice.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the codec is master then prepare should call
mcbsp_start, not trigger.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Code previously just "ors" in this field without clearing
first. Fix, by never reading this register.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only start sample generator if needed, and more
cleanup on davinci_mcbsp_start.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move variable declaration closer to use.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add davinci_mcbsp_dev as argument to davinci_mcbsp_start
and davinci_mcbsp_stop.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add toggle_clock function to complete i2s reset earlier.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No functional changes. Rename variable w to something
more meaningful. Remove code obfuscating macro MOD_REG_BIT.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Assign proper errors when platform resource claims fail.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch does the following:
(1) Add support for the DM646x machine
(2) Modifications required to introduce the platform driver model to get
platform data for all the machines including dm355 and dm644x.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds driver support for the two instances of McASP on TI's DM646x.
The multichannel audio serial port (McASP) functions as a general-purpose audio
serial port optimized for the needs of multichannel audio application.
(http://www.ti.com/litv/pdf/spruer1b).
There are two instances of McASP on DM646x. The McASP0 module includes up to 4
serializers that can be individually enabled to either transmit or receive
in different modes. The McASP1 module is limited with only 1 pinned-out
serializer that can be enabled to only transmit in DIT mode (neither receiving
in any mode nor transmitting in either Burst or TDM mode is supported).
McASP0 consists of transmit and receive sections that may operate
synchronized, or completely independently with separate master clocks, bit
clocks, and frame syncs, and using different transmit modes with different
bit-stream formats.
Signed-off-by: Steve Chen <schen@mvista.com>
Signed-off-by: Pavel Kiryukhin <pkiryukhin@ru.mvista.com>
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce the platform driver model to get platform data for dm355 and dm644x.
Register platform driver and acquire the resources in the probe function Since
the platform specific code had been moved from machine driver to dm<soc>.c
Signed-off-by: Naresh Medisetty <naresh@ti.com>
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree. That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.
(NOTE: also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This resyncs the DaVinci I2S code with the version in the DaVinci
tree. The behavioral change uses updated clock interfaces which
recently merged to mainline. Two other changes include adding a
comment on the ASP/McBSP/McASP confusion, and dropping pdev->id in
order to support more boards than just the DM644x EVM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds