Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a new driver for Capella CM36651 proximity and RGB sensor.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a new driver for the ambient light/proximity sensor
device. The driver exposes three channels: light_clear
light_ir and proximity. It also supports triggered buffer,
high and low ambient light threshold event and proximity
detection events.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
chip has four 16-bit channels for red, green, blue, clear color
intensity; driver supports the TCS3x7x family of devices and was
tested with a TCS34725 chip; further information here:
http://www.ams.com/eng/Products/Light-Sensors/Color-Sensor/TCS34725
v2 (thanks to Jonathan Cameron):
* drop dynamic buffer allocation, buffer is in tcs3472_data
* limit sysfs output to PAGE_SIZE
* check val2 == 0 when writing CALIBSCALE
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jon Brenner <jon.brenner@ams.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
driver for the TSL4531 family of 16-bit I2C ambient light
sensors; information is here:
http://www.ams.com/eng/Products/Light-Sensors/Ambient-Light-Sensor-ALS/TSL45315
the chip offers simple lux output
v3 (thanks Lars-Peter Clausen):
* add mutex to when updating integration time
* fix chip ID checking
* code cleanups
v2:
* rename to tsl4351
* use INT_TIME
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds IIO driver for APDS9300 ambient light sensor (ALS).
http://www.avagotech.com/docs/AV02-1077EN
The driver allows to read raw data from ADC registers or calculate
lux value. It also can handle threshold interrupt.
Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Keeping Makefile and Kconfig entries in alphabetical order usually works better
than just appending new entries at the end, since it reduces the amount of
conflicts. This patch adds a comment to the IIO Kconfig and Makefile files to
document that the entries should be kept in alphabetical order.
Also reorder those entries which weren't in alphabetical order yet.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This driver is simple, uses the latest interfaces and contains few if
any controversial elements. All of its interfaces have been in place
for a long time now. Hence let's move it out of staging.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Added usage id processing for ALS. This uses IIO
interfaces for triggered buffer to present data to user
mode.This uses HID sensor framework for registering callback
events from the sensor hub.
Signed-off-by: srinivas pandruvada <srinivas.pandruvada@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
sensor has 4 channels (10-bit each, R/G/B and clear), sensitivity
and gain is controlled in the driver by ext_info integration_time
and CHAN_INFO_HARDWAREGAIN
driver supports triggered buffer and IIO_CHAN_INFO_RAW to get the
sensor data
v5: address comments by Jonathan Cameron
* use macro for channel declaration
* get timestamp right before measurement
* cleanups
v4: address comments by Lars-Peter Clausen
* make sure trigger handler is exited with iio_trigger_notify_done()
and IRQ_HANDLED
* kfree()/kalloc() -> krealloc()
v3:
* fix warnings
v2: address comments by Lars-Peter Clausen
* buffer allocation now in update_scan_mode instead of in trigger
handler
* simplify trigger code (assume active_scan_mask is not empty, use
for_each_set_bit, use iio_push_to_buffer)
* reorder entry in Makefile and Kconfig
* fix remove
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
minimal driver, no IR current control and proximity/event
handling yet
v5:
* checkpatch warnings
* increase msleep() to 20 ms when waiting for data ready as
measurement/conversion can take up to 100 ms, 1 ms is too short
v4 (address comments by Jonathan Cameron)
* remove SENSORS_ prefix in Kconfig
* change from IIO_INTENSITY to IIO_LIGHT
* move from staging
v3 (address comments by Shubhrajyoti Datta)
* cleanup Kconfig entry
* call I2C read/write functions directly
v2 (address comments by Lars-Peter Clausen and Jonathan Cameron)
* unify code for reading PS and AL data into
parameterized _measure() function
* limit wait for data to become ready within 20 tries
* drop IIO_LIGHT channel, add SCALE to IIO_INTENSITY
* drop extra string arguments used for logging purpose only
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sub-driver for the ambient-light-sensor interface on National
Semiconductor / TI LM3533 lighting power chips.
The sensor interface can be used to control the LEDs and backlights of
the chip through defining five light zones and three sets of
corresponding output-current values.
The driver provides raw and mean adc readings along with the current
light zone through sysfs. A threshold event can be generated on zone
changes. The ALS-control output values can be set per zone for the three
current output channels.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kevin Tsai