Pull libata fixes from Tejun Heo:
"Nothing too interesting.
Arnd's gcc-7 warning fixes that slipped through the cracks for two
release cycles (my bad), and two minor low level driver updates"
* 'for-4.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: don't ignore result code of ahci_reset_controller()
ata_piix: Add Fujitsu-Siemens Lifebook S6120 to short cable IDs
ata: avoid gcc-7 warning in ata_timing_quantize
Here are a number of USB fixes for 4.14-rc4 to resolved reported issue.
There's a bunch of stuff in here based on the great work Andrey
Konovalov is doing in fuzzing the USB stack. Lots of bug fixes when
dealing with corrupted USB descriptors that we've never seen in "normal"
operation, but is now ensuring the stack is much more hardened overall.
There's also the usual XHCI and gadget driver fixes as well, and a build
error fix, and a few other minor things, full details in the shortlog.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWdN/yw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl6pQCdGY+nPJhzj9EIeFj5QUpSuS4b1pYAoKrbNn+V
CMpg4iG1oXUtVL8jBbKa
=fVpl
-----END PGP SIGNATURE-----
Merge tag 'usb-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.14-rc4 to resolved reported
issues.
There's a bunch of stuff in here based on the great work Andrey
Konovalov is doing in fuzzing the USB stack. Lots of bug fixes when
dealing with corrupted USB descriptors that we've never seen in
"normal" operation, but is now ensuring the stack is much more
hardened overall.
There's also the usual XHCI and gadget driver fixes as well, and a
build error fix, and a few other minor things, full details in the
shortlog.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (38 commits)
usb: dwc3: of-simple: Add compatible for Spreadtrum SC9860 platform
usb: gadget: udc: atmel: set vbus irqflags explicitly
usb: gadget: ffs: handle I/O completion in-order
usb: renesas_usbhs: fix usbhsf_fifo_clear() for RX direction
usb: renesas_usbhs: fix the BCLR setting condition for non-DCP pipe
usb: gadget: udc: renesas_usb3: Fix return value of usb3_write_pipe()
usb: gadget: udc: renesas_usb3: fix Pn_RAMMAP.Pn_MPKT value
usb: gadget: udc: renesas_usb3: fix for no-data control transfer
USB: dummy-hcd: Fix erroneous synchronization change
USB: dummy-hcd: fix infinite-loop resubmission bug
USB: dummy-hcd: fix connection failures (wrong speed)
USB: cdc-wdm: ignore -EPIPE from GetEncapsulatedResponse
USB: devio: Don't corrupt user memory
USB: devio: Prevent integer overflow in proc_do_submiturb()
USB: g_mass_storage: Fix deadlock when driver is unbound
USB: gadgetfs: Fix crash caused by inadequate synchronization
USB: gadgetfs: fix copy_to_user while holding spinlock
USB: uas: fix bug in handling of alternate settings
usb-storage: unusual_devs entry to fix write-access regression for Seagate external drives
usb-storage: fix bogus hardware error messages for ATA pass-thru devices
...
Here are a small number (5) of patches for some reported TTY and serial
issues. Nothing major, a documentation update, timing fix, error
handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWdN+uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykZmgCbBSJmwcbVhuhZ64Fx4OE0eprjOgoAoMLmHaT2
jTjQTxM/Gaz108t3o9rt
=5ve+
-----END PGP SIGNATURE-----
Merge tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number (5) of patches for some reported TTY and
serial issues. Nothing major, a documentation update, timing fix,
error handling fix, name reporting fix, and a timeout issue resolved.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sccnxp: Fix error handling in sccnxp_probe()
tty: serial: lpuart: avoid report NULL interrupt
serial: bcm63xx: fix timing issue.
mxser: fix timeout calculation for low rates
serial: sh-sci: document R8A77970 bindings
Here are some small staging/IIO driver fixes for 4.14-rc4
Most of these have been in my tree for a while due to travels, sorry for
the delay. They resolve a number of small issues reported by people,
mostly for the iio drivers. Nothing major in here, full details are in
the shortlog.
All have been linux-next for a few weeks with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWdN+KQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yluygCgneh7i/okOfsmt/p75eCA4ClWVLwAoIE7BZzt
1WdBcY/Zxv1ANIoY7ZTQ
=K+FX
-----END PGP SIGNATURE-----
Merge tag 'staging-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are some small staging/IIO driver fixes for 4.14-rc4
Most of these have been in my tree for a while due to travels, sorry
for the delay. They resolve a number of small issues reported by
people, mostly for the iio drivers. Nothing major in here, full
details are in the shortlog.
All have been linux-next for a few weeks with no reported issues"
* tag 'staging-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
staging: iio: ad7192: Fix - use the dedicated reset function avoiding dma from stack.
iio: core: Return error for failed read_reg
iio: ad7793: Fix the serial interface reset
iio: ad_sigma_delta: Implement a dedicated reset function
IIO: BME280: Updates to Humidity readings need ctrl_reg write!
iio: adc: mcp320x: Fix readout of negative voltages
iio: adc: mcp320x: Fix oops on module unload
iio: adc: stm32: fix bad error check on max_channels
iio: trigger: stm32-timer: fix a corner case to write preset
iio: trigger: stm32-timer: preset shouldn't be buffered
iio: adc: twl4030: Return an error if we can not enable the vusb3v1 regulator in 'twl4030_madc_probe()'
iio: adc: twl4030: Disable the vusb3v1 rugulator in the error handling path of 'twl4030_madc_probe()'
iio: adc: twl4030: Fix an error handling path in 'twl4030_madc_probe()'
staging: rtl8723bs: avoid null pointer dereference on pmlmepriv
staging: rtl8723bs: add missing range check on id
staging: vchiq_2835_arm: Fix NULL ptr dereference in free_pagelist
staging: speakup: fix speakup-r empty line lockup
staging: pi433: Move limit check to switch default to kill warning
staging: r8822be: fix null pointer dereferences with a null driver_adapter
staging: mt29f_spinand: Enable the read ECC before program the page
...
We've had support for setting both a minimum and maximum bandwidth via
.ndo_set_vf_bw since commit 883a9ccbae ("fm10k: Add support for SR-IOV
to driver", 2014-09-20).
Likely because we do not support minimum rates, the declaration
mis-ordered the "unused" parameter, which causes warnings when analyzed
with cppcheck.
Fix this warning by properly declaring the min_rate and max_rate
variables in the declaration and definition (rather than using
"unused"). Also rename "rate" to max_rate so as to clarify that we only
support setting the maximum rate.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Here are a few small fixes for 4.14-rc4.
The removal of DRIVER_ATTR() was almost completed by 4.14-rc1, but one
straggler made it in through some other tree (odds are, one of mine...)
So there's a simple removal of the last user, and then finally the macro
is removed from the tree.
There's a fix for old crazy udev instances that insist on reloading a
module when it is removed from the kernel due to the new uevents for
bind/unbind. This fixes the reported regression, hopefully some year in
the future we can drop the workaround, once users update to the latest
version, but I'm not holding my breath.
And then there's a build fix for a linker warning, and a buffer overflow
fix to match the PCI fixes you took through the PCI tree in the same
area.
All of these have been in linux-next for a few weeks while I've been
traveling, sorry for the delay.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWdN8qA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymLEgCfUSSBhxW04teEcPua4QygLv2omK0An2SRkpnY
28nn+D+AfeOByQImY8v+
=RQY+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are a few small fixes for 4.14-rc4.
The removal of DRIVER_ATTR() was almost completed by 4.14-rc1, but one
straggler made it in through some other tree (odds are, one of
mine...) So there's a simple removal of the last user, and then
finally the macro is removed from the tree.
There's a fix for old crazy udev instances that insist on reloading a
module when it is removed from the kernel due to the new uevents for
bind/unbind. This fixes the reported regression, hopefully some year
in the future we can drop the workaround, once users update to the
latest version, but I'm not holding my breath.
And then there's a build fix for a linker warning, and a buffer
overflow fix to match the PCI fixes you took through the PCI tree in
the same area.
All of these have been in linux-next for a few weeks while I've been
traveling, sorry for the delay"
* tag 'driver-core-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
driver core: remove DRIVER_ATTR
fpga: altera-cvp: remove DRIVER_ATTR() usage
driver core: platform: Don't read past the end of "driver_override" buffer
base: arch_topology: fix section mismatch build warnings
driver core: suppress sending MODALIAS in UNBIND uevents
Don't hard code the function names in the diagnostic output when these
reset related routines fail. Instead, use %s and __func__ so that future
refactors don't need to change the print outs.
Additionally, while we are here, add missing function header comments
for the new reset_prepare and reset_done function handlers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct the backward logic using !net_ratelimit()
Miscellanea:
o Add a blank line before the error return label
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we have a working MAC/VLAN queue for handling MAC/VLAN messages
from the netdev, replace the default handler for the VF<->PF messages.
This new handler is very similar to the default code, but uses the
MAC/VLAN queue instead of sending the message directly. Unfortunately we
can't easily re-use the default code, so we'll just replace the entire
function.
This ensures that a VF requesting a large number of VLANs or MAC
addresses does not start a reset cycle, as explained in the commit which
introduced the message queue.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Ngai-mint Kwan <ngai-mint.kwan@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Here are a handful of char/misc driver fixes for 4.14-rc4.
Nothing major, some binder fixups, hyperv fixes, and other tiny things.
All of these have been sitting in my tree for way too long, sorry for
the delay in getting them to you. All have been in linux-next for a few
weeks, and despite some people's feeling about if linux-next actually
tests things, I think it's a good "soak test" for patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWdN4YA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yluhQCgmL0xgVGvO5uXNNwY+PsWdp7cELYAoNmGxVoP
AKnvi1ZeDNSu1+O3+j6Q
=wjBg
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg KH:
"Here are a handful of char/misc driver fixes for 4.14-rc4.
Nothing major, some binder fixups, hyperv fixes, and other tiny
things.
All of these have been sitting in my tree for way too long, sorry for
the delay in getting them to you. All have been in linux-next for a
few weeks, and despite some people's feeling about if linux-next
actually tests things, I think it's a good "soak test" for patches"
* tag 'char-misc-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Drivers: hv: fcopy: restore correct transfer length
vmbus: don't acquire the mutex in vmbus_hvsock_device_unregister()
intel_th: pci: Add Lewisburg PCH support
intel_th: pci: Add Cedar Fork PCH support
stm class: Fix a use-after-free
nvmem: add missing of_node_put() in of_nvmem_cell_get()
nvmem: core: return EFBIG on out-of-range write
auxdisplay: charlcd: properly restore atomic counter on error path
binder: fix memory corruption in binder_transaction binder
binder: fix an ret value override
android: binder: fix type mismatch warning
Under some circumstances, when dealing with a large number of MAC
address or VLAN updates at once, the fm10k driver, particularly the VFs
can overload the mailbox with too many messages at once.
This results in a mailbox timeout, which causes the driver to initiate
a reset. During the reset, we re-send all the same messages that
originally caused the timeout. This results in a cycle of resets each
triggering a future reset.
To fix or avoid this, we introduce a workqueue item which monitors
a queue of MAC and VLAN requests. These requests are queued to the end
of the list, and we process as a FIFO periodically.
Initially we only handle requests for the netdev, but we do handle
unicast MAC addresses, multicast MAC addresses, and update VLAN
requests.
A future patch will add support to use this queue for handling MAC
update requests from the VF<->PF mailbox.
The MAC/VLAN work item will keep checking to make sure that each request
does not overflow the mailbox and cause a timeout. If it might, then the
work item will reschedule itself a short time later. This avoids any
reset cycle, since we never send the message if the mailbox is not
ready.
As an alternative, we tried increasing the mailbox message FIFO, but
this just delays the problem and results in needless memory waste on the
system. Our new message queue is dynamically allocated so only uses as
much memory as it needs. Additionally, it need not be contiguous like
the Tx and Rx FIFOs.
Note that this patch chose to only create a queue for MAC and VLAN
messages, since these are the only messages sent in a large enough
volume to cause the reset loop. Other messages are very unlikely to
overflow the mailbox Tx FIFO so easily.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the PCI specific legacy power management hooks with the new
generic power management hooks which work properly for both suspend and
hibernate. The new generic system is better and properly handles the
lower level PCIe power management rather than forcing the driver to
handle it.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Lets not re-invent the locking wheel. Remove our bitlock and use
a proper spinlock instead.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we lose PCIe link, such as when an unannounced PFLR event occurs, or
when a device is surprise removed, we currently detach the device and
close the netdev. This unfortunately leaves a lot of things still
active, such as the msix_mbx_pf IRQ, and Tx/Rx resources.
This can cause problems because the register reads will return
potentially invalid values which may result in unknown driver behavior.
Begin the process of resetting using fm10k_prepare_for_reset(), much in
the same way as the suspend and resume cycle does. This will attempt to
shutdown as much as possible, in order to prevent possible issues.
A naive implementation for this has issues, because there are now
multiple flows calling the reset logic and setting a reset bit. This
would cause problems, because the "re-attach" routine might call
fm10k_handle_reset() prior to the reset actually finishing. Instead,
we'll add state bits to indicate which flow actually initiated the
reset.
For the general reset flow, we'll assume that if someone else is
resetting that we do not need to handle it at all, so it does not need
its own state bit. For the suspend case, we will simply issue a warning
indicating that we are attempting to recover from this case when
resuming.
For the detached subtask, we'll simply refuse to re-attach until we've
actually initiated a reset as part of that flow.
Finally, we'll stop attempting to manage the mailbox subtask when we're
detached, since there's nothing we can do if we don't have a PCIe
address.
Overall this produces a much cleaner shutdown and recovery cycle for
a PCIe surprise remove event.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The read of ->dynticks_nmi_nesting in rcu_irq_enter() and rcu_irq_exit()
is currently protected with READ_ONCE(). However, this protection is
unnecessary because (1) ->dynticks_nmi_nesting is updated only by the
current CPU, (2) Although NMI handlers can update this field, they reset
it back to its old value before return, and (3) Interrupts are disabled,
so nothing else can modify it. The value of ->dynticks_nmi_nesting is
thus effectively constant, and so no protection is required.
This commit therefore removes the READ_ONCE() protection from these
two accesses.
Link: http://lkml.kernel.org/r/20170926031902.GA2074@linux.vnet.ibm.com
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
The trampoline allocated by function tracer was overwriten by function_graph
tracer, and caused a memory leak. The save_global_trampoline should have
saved the previous trampoline in register_ftrace_graph() and restored it in
unregister_ftrace_graph(). But as it is implemented, save_global_trampoline was
only used in unregister_ftrace_graph as default value 0, and it overwrote the
previous trampoline's value. Causing the previous allocated trampoline to be
lost.
kmmeleak backtrace:
kmemleak_vmalloc+0x77/0xc0
__vmalloc_node_range+0x1b5/0x2c0
module_alloc+0x7c/0xd0
arch_ftrace_update_trampoline+0xb5/0x290
ftrace_startup+0x78/0x210
register_ftrace_function+0x8b/0xd0
function_trace_init+0x4f/0x80
tracing_set_tracer+0xe6/0x170
tracing_set_trace_write+0x90/0xd0
__vfs_write+0x37/0x170
vfs_write+0xb2/0x1b0
SyS_write+0x55/0xc0
do_syscall_64+0x67/0x180
return_from_SYSCALL_64+0x0/0x6a
[
Looking further into this, I found that this was left over from when the
function and function graph tracers shared the same ftrace_ops. But in
commit 5f151b2401 ("ftrace: Fix function_profiler and function tracer
together"), the two were separated, and the save_global_trampoline no
longer was necessary (and it may have been broken back then too).
-- Steven Rostedt
]
Link: http://lkml.kernel.org/r/20170912021454.5976-1-shuwang@redhat.com
Cc: stable@vger.kernel.org
Fixes: 5f151b2401 ("ftrace: Fix function_profiler and function tracer together")
Signed-off-by: Shu Wang <shuwang@redhat.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Starting from linux-4.4, 3WHS no longer takes the listener lock.
Since this time, we might hit a use-after-free in sk_filter_charge(),
if the filter we got in the memcpy() of the listener content
just happened to be replaced by a thread changing listener BPF filter.
To fix this, we need to make sure the filter refcount is not already
zero before incrementing it again.
Fixes: e994b2f0fb ("tcp: do not lock listener to process SYN packets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-02
This series contains updates to i40e and i40evf.
Shannon Nelson fixes an issue where when a machine has more CPUs than
queue pairs, the counting gets a "little funky" and turns off Flow
Director. So to correct it, limit the number of LAN queues initially
allocated to be sure there are some left for Flow Director and other
features.
Lihong cleans up dead code by removing a condition check which cannot
ever be true.
Christophe Jaillet fixes a potential NULL pointer dereference, which
could happen if kzalloc() fails.
Filip corrects the reporting of supported link modes, which was incorrect
for some NICs. Added support for 'ethtool -m' command, which displays
information about QSFP+ modules.
Mariusz adds functions to read/write the LED registers to control the
LEDS, instead of accessing the registers directly whenever the LEDs
need to be controlled.
Jake fixes a regression where we introduced a scheduling while atomic,
so introduce a separate helper function which will manage its own need
for the mac_filter_hash_lock. Also cleaned up the "PF" parameter in
i40e_vc_disable_vf() since it is never used and is not needed. Fixed
a rare case where it is possible that a reset does not occur when
i40e_vc_disable_vf() is called, so modify i40e_reset_vf() to return a
bool to indicate whether it reset or not so that i40e_vc_disable_vf()
can wait until a reset actually occurs.
Alan adds the ability for the VF to request more or less underlying
allocated queues from the PF. Fixes the incorrect method for clearing
the vf_states variable with a NULL assignment, when we should be
using atomic bitops since we don't actually want to clear all the
flags. Fixed a resource leak, where the PF driver fails to inform
clients of a VF reset because we were incorrectly checking the
I40E_VF_STATE_PRE_ENABLE bit.
Mitch converts i40evf_map_rings_to_vectors() to a void function since
it cannot fail and allows us to clean up the checks for the function
return value.
Scott enables the driver(s) to pass traffic with VLAN tags using the
802.1ad Ethernet protocol.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).
This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.
No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently there is a bug in which the PF driver fails to inform clients
of a VF reset which then causes clients to leak resources. The bug
exists because we were incorrectly checking the I40E_VF_STATE_PRE_ENABLE
bit.
When a VF is first init we go through a reset to initialize variables
and allocate resources but we don't want to inform clients of this first
reset since the client isn't fully enabled yet so we set a state bit
signifying we're in a "pre-enabled" client state. During the first
reset we should be clearing the bit, allowing all following resets to
notify the client of the reset when the bit is not set. This patch
fixes the issue by negating the 'test_and_clear_bit' check to accurately
reflect the behavior we want.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we inappropriately clear the vf_states variable with a null
assignment. This is problematic because we should be using atomic
bitops on this variable and we don't actually want to clear all the
flags. We should just clear the ones we know we want to clear.
Additionally remove the I40E_VF_STATE_FCOEENA bit because it is no
longer being used.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This function cannot fail, so why is it returning a value? And why are
we checking it? Why shouldn't we just make it void? Why is this commit
message made up of only questions?
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the VF gets a default number of allocated queues from HW on
init and it could choose to enable or disable those allocated queues.
This makes it such that the VF can request more or less underlying
allocated queues from the PF.
First the VF negotiates the number of queues it wants that can be
supported by the PF and if successful asks for a reset. During reset
the PF will reallocate the HW queues for the VF and will then remap the
new queues.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It is possible although rare that we may not reset when
i40e_vc_disable_vf() is called. This can lead to some weird
circumstances with some values not being properly set. Modify
i40e_reset_vf() to return a code indicating whether it reset or not.
Now, i40e_vc_disable_vf() can wait until a reset actually occurs. If it
fails to free up within a reasonable time frame we'll display a warning
message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace i40e_vc_notify_vf_reset and i40e_reset_vf with a call to
i40e_vc_disable_vf which does this exact thing. This matches similar
code patterns throughout the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It's never used, and the vf structure could get back to the PF if
necessary. Lets just drop the extra unneeded parameter.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we refactored handling of the PVID in commit 9af52f60b2
("i40e: use (add|rm)_vlan_all_mac helper functions when changing PVID")
we introduced a scheduling while atomic regression.
This occurred because we now held the spinlock across a call to
i40e_reset_vf(), which results in a usleep_range() call that triggers
a scheduling while atomic bug. This was rare as it only occurred if the
user configured a VLAN on a VF and also attempted to reconfigure the VF
from the host system with a port VLAN.
We do need to hold the lock while calling i40e_is_vsi_in_vlan(), but we
should not be holding it while we reset the VF.
We'll fix this by introducing a separate helper function
i40e_vsi_has_vlans which checks whether we have a PVID and whether the
VSI has configured VLANs. This helper function will manage its own need
for the mac_filter_hash_lock.
Then, we can move the acquiring of the spinlock until after we reset the
VF, which ensures that we do not sleep while holding the lock.
Using a separate function like this makes the code more clear and is
easier to read than attempting to release and re-acquire the spinlock
when we reset the VF.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of accessing register directly, use newly added AQC in
order to blink LEDs. Introduce and utilize a new flag to prevent
excessive API version checking.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for 'ethtool -m' command which displays
information about (Q)SFP+ module plugged into NIC's cage.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes incorrect reporting of supported link modes on some NICs.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If 'kzalloc()' fails, a NULL pointer will be dereferenced.
Return an error code (-ENOMEM) instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the !vf condition check that cannot be
true in i40e_ndo_set_vf_trust function
Detected by CoverityScan, CID 1397531 Logically dead code
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a machine has more CPUs than queue pairs, e.g. 512 cores, the
counting gets a little funky and turns off Flow Director with the
message:
not enough queues for Flow Director. Flow Director feature is disabled
This patch limits the number of lan queues initially allocated to
be sure we have some left for FD and other features.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2017-10-02
This series contains updates to fm10k only.
Jake provides all but one of the changes in this series. Most are small
fixes, starting with ensuring prompt transmission of messages queued up
after each VF message is received and handled. Fix a possible race
condition between the watchdog task and the processing of mailbox
messages by just checking whether the mailbox is still open. Fix a
couple of GCC v7 warnings, including misspelled "fall through" comments
and warnings about possible truncation of calls to snprintf(). Cleaned
up a convoluted bitshift and read for the PFVFLRE register. Fixed a
potential divide by zero when finding the proper r_idx.
Markus Elfring fixes an issue which was found using Coccinelle, where
we should have been using seq_putc() instead of seq_puts().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mika Westerberg says:
====================
Thunderbolt networking
In addition of tunneling PCIe, Display Port and USB traffic, Thunderbolt
allows connecting two hosts (domains) over a Thunderbolt cable. It is
possible to tunnel arbitrary data packets over such connection using
high-speed DMA rings available in the Thunderbolt host controller.
In order to discover Thunderbolt services the other host supports, there is
a software protocol running on top of the automatically configured control
channel (ring 0). This protocol is called XDomain discovery protocol and it
uses XDomain properties to describe the host (domain) and the services it
supports.
Once both sides have agreed what services are supported they can enable
high-speed DMA rings to transfer data over the cable.
This series adds support for the XDomain protocol so that we expose each
remote connection as Thunderbolt XDomain device and each service as
Thunderbolt service device. On top of that we create an API that allows
writing drivers for these services and finally we provide an example
Thunderbolt service driver that creates virtual ethernet inferface that
allows tunneling networking packets over Thunderbolt cable. The API could
be used for creating other future Thunderbolt services, such as tunneling
SCSI over Thunderbolt, for example.
The XDomain protocol and networking support is also available in macOS and
Windows so this makes it possible to connect Linux to macOS and Windows as
well.
The patches are based on previous Thunderbolt networking patch series by
Amir Levy and Michael Jamet, that can be found here:
https://lwn.net/Articles/705998/
The main difference to that patch series is that we have the XDomain
protocol running in the kernel now so there is no need for a separate
userspace daemon.
Note this does not affect the existing functionality, so security levels
and NVM firmware upgrade continue to work as before (with the small
exception that now sysfs also shows the XDomain connections and services in
addition to normal Thunderbolt devices). It is also possible to connect up
to 5 Thunderbolt devices and then another host, and the network driver
works exactly the same.
This is third version of the patch series. The previous versions can be
be found here:
v2: https://lkml.org/lkml/2017/9/25/225
v1: https://lwn.net/Articles/734019/
Changes from the v2:
* Add comment regarding calculation of interrupt throttling value
* Add UUIDs as strings in comments on top of each declaration
* Add a patch removing __packed from existing ICM messages. They are all
32-bit aligned and should pack fine without the __packed.
* Move adding MAINTAINERS entries to a separate patches
* Added Michael and Yehezkel to be maintainers of the network driver
* Remove __packed from the new ICM messages. They should pack fine as
well without it.
* Call register_netdev() after all other initialization is done in the
network driver.
* Use build_skb() instead of copying. We allocate order 1 page here to
leave room for SKB shared info required by build_skb(). However, we do
not leave room for full NET_SKB_PAD because the NHI hardware does not
cope well if a frame crosses 4kB boundary. According comments in
__build_skb() that should still be fine.
* Added Reviewed-by tag from Andy.
Changes from the v1:
* Add include/linux/thunderbolt.h to MAINTAINERS
* Correct Linux version and date of new sysfs entries in
Documentation/ABI/testing/sysfs-bus-thunderbolt
* Move network driver from drivers/thunderbolt/net.c to
drivers/net/thunderbolt.c and update it to follow coding style in
drivers/net/*.
* Add MAINTAINERS entry for the network driver
* Minor cleanups
In case someone wants to try this out, the last patch adds documentation
how the networking driver can be used. In short, if you connect Linux to a
macOS or Windows, everything is done automatically (as those systems have
the networking service enabled by default). For Linux to Linux connection
one host needs to load the networking driver first (so that the other side
can locate the networking service and load the corresponding driver).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I will be maintaining the Thunderbolt network driver along with Michael
and Yehezkel.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ThunderboltIP is a protocol created by Apple to tunnel IP/ethernet
traffic over a Thunderbolt cable. The protocol consists of configuration
phase where each side sends ThunderboltIP login packets (the protocol is
determined by UUID in the XDomain packet header) over the configuration
channel. Once both sides get positive acknowledgment to their login
packet, they configure high-speed DMA path accordingly. This DMA path is
then used to transmit and receive networking traffic.
This patch creates a virtual ethernet interface the host software can
use in the same way as any other networking interface. Once the
interface is brought up successfully network packets get tunneled over
the Thunderbolt cable to the remote host and back.
The connection is terminated by sending a ThunderboltIP logout packet
over the configuration channel. We do this when the network interface is
brought down by user or the driver is unloaded.
Signed-off-by: Amir Levy <amir.jer.levy@intel.com>
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new API header (include/linux/thunderbolt.h) is maintained by the
Thunderbolt driver maintainers.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thunderbolt services should not care which HopID (ring) they use for
sending and receiving packets over the high-speed DMA path, so make
tb_ring_alloc_rx() and tb_ring_alloc_tx() accept negative HopID. This
means that the NHI will allocate next available HopID for the caller
automatically.
These HopIDs will be allocated from the range which is not reserved for
the Thunderbolt protocol (8 .. hop_count - 1).
The allocated HopID can be retrieved from ring->hop field after the ring
has been allocated successfully if needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed when Thunderbolt service drivers need to DMA map memory
before it is passed down to the ring.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support things like networking over Thunderbolt cable, there
needs to be a way to switch the ring to a mode where it can be polled
with the interrupt masked. We implement such mode so that the caller can
allocate a ring by passing pointer to a function that is then called
when an interrupt is triggered. Completed frames can be fetched using
tb_ring_poll() and the interrupt can be re-enabled when the caller is
finished with polling by using tb_ring_poll_complete().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is needed because ring polling functionality can be called from
atomic contexts when networking and other high-speed traffic is
transferred over a Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes it possible to enqueue frames also from atomic context which
is needed for example, when networking packets are sent over a
Thunderbolt cable.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A Thunderbolt service driver might need to check if there was an error
with the descriptor when in frame mode. We also add two Rx specific
error flags RING_DESC_CRC_ERROR and RING_DESC_BUFFER_OVERRUN.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are used by Thunderbolt services to send and receive frames over
the high-speed DMA rings.
We also put the functions to tb_ namespace to make sure we do not
collide with others and add missing kernel-doc comments for the exported
functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Michael Jamet <michael.jamet@intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When high-speed DMA paths are used to transfer arbitrary data over a
Thunderbolt link, DMA rings should be in frame mode instead of raw mode.
The latter is used by the control channel (ring 0). In frame mode each
data frame can hold up to 4kB payload.
This patch modifies the DMA ring code to allow configuring a ring to be
in frame mode by passing a new flag (RING_FLAG_FRAME) to the ring when
it is allocated. In addition there might be need to enable end-to-end
(E2E) workaround for the ring to prevent losing Rx frames in certain
situations. We add another flag (RING_FLAG_E2E) that can be used for
this purpose.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will keep the interrupt delivery rate reasonable. The value used
here (128 us) is a recommendation from the hardware people.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two hosts are connected over a Thunderbolt cable, there is a
protocol they can use to communicate capabilities supported by the host.
The discovery protocol uses automatically configured control channel
(ring 0) and is build on top of request/response transactions using
special XDomain primitives provided by the Thunderbolt base protocol.
The capabilities consists of a root directory block of basic properties
used for identification of the host, and then there can be zero or more
directories each describing a Thunderbolt service and its capabilities.
Once both sides have discovered what is supported the two hosts can
setup high-speed DMA paths and transfer data to the other side using
whatever protocol was agreed based on the properties. The software
protocol used to communicate which DMA paths to enable is service
specific.
This patch adds support for the XDomain discovery protocol to the
Thunderbolt bus. We model each remote host connection as a Linux XDomain
device. For each Thunderbolt service found supported on the XDomain
device, we create Linux Thunderbolt service device which Thunderbolt
service drivers can then bind to based on the protocol identification
information retrieved from the property directory describing the
service.
This code is based on the work done by Amir Levy and Michael Jamet.
Signed-off-by: Michael Jamet <michael.jamet@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds