CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, and __devexit from these
drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Michael Buesch <m@bues.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Use WARN rather than printk followed by WARN_ON(1), for conciseness.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register the watchdog driver to the system if it is a SoC. Using the
watchdog on a non SoC device, like a PCI card, will make the PCI
card die when the timeout expired, but starting it again is not
supported by ssb.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, add a method converting ms to ticks before setting the watchdog
register. Return the ticks or millisecond the timer was set to in case
the provided value was bigger than the max allowed value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prevent the watchdog register on the extif core to be set to a too
high value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The watchdog driver wants to set the watchdog timeout in ms and not in
ticks, which is depending on the SoC type and the clock.
Calculate the number of ticks per millisecond and provide two functions
for the watchdog driver. Also return the ticks or millisecond the timer
was set to in case the provided value was bigger than the max allowed
value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some ssb based devices have a PMU and the PMU watchdog register should
be used instead of the register in the chip common part, if the device
has a PMU. This patch also calculates the maximal number the watchdog
could be set to.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If there is a PMU in the device, get the alp clock from that part and
do not assume 20000000.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If CONFIG_SSB_EMBEDDED or CONFIG_SSB_DRIVER_MIPS is set and
CONFIG_SSB_DRIVER_EXTIF is not set, it will cause compile problems
because of missing functions. This patch fixes these problems.
The mips driver now also uses ssb_chipco_available() instead of
checking bus->chipco.dev manually.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4591
Acked-by: Florian Fainelli <florian@openwrt.org>
The GPIOs are access through some registers in the chip common core or
over extif. We need locking around these GPIO accesses, all GPIOs are
accessed through the same registers and parallel writes will cause
problems.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4590
Acked-by: Florian Fainelli <florian@openwrt.org>
Add functions to access the GPIO registers for pullup and pulldown.
These are needed for handling gpio registration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4589
Acked-by: Florian Fainelli <florian@openwrt.org>
The BCM43222 with the chipid 43222 or 0xa8d6 in hex do not need any
special handling in the pmu code. This prevents some error messages
being shown.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a preparing step for adding serial flash support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We can not assume parallel flash is always present, there are boards
with *serial* flash and probably some without flash at all.
Define some bits by the way.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
14e4:432c is found on some bcm63xx devices. The device is working fine
with b43.
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I found this core on a BCM4322, a PCI card in the Linksys WRT610N V1.
This core is not used by the driver, this patch just makes ssb show the
correct name.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 0x4322 ID is found on the BCM4322 used on some SoCs like the
Linksys WRT610N V1 connected to a BCM4705. The 43222 (0xa8d6) ID
is found on the BCM43222 used on some other SoCs like the D-Link
DSL-2760U connected to a BCM63xx.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These newly added attributes are used by brcmsmac. Now bcma should
parse all attributes used by brcmsmac out of the sprom.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This attribute is now used in b43 driver and should be filled for all
sprom versions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The attribute country_code and alpha2 are two different attributes in
the sprom. country_code contains some code in an 8 bit coding and
alpha2 contains two chars with the country code. The attributes where
read out wrongly in the past and country_code is only available on
sprom version 1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull networking merge from David Miller:
"1) Move ixgbe driver over to purely page based buffering on receive.
From Alexander Duyck.
2) Add receive packet steering support to e1000e, from Bruce Allan.
3) Convert TCP MD5 support over to RCU, from Eric Dumazet.
4) Reduce cpu usage in handling out-of-order TCP packets on modern
systems, also from Eric Dumazet.
5) Support the IP{,V6}_UNICAST_IF socket options, making the wine
folks happy, from Erich Hoover.
6) Support VLAN trunking from guests in hyperv driver, from Haiyang
Zhang.
7) Support byte-queue-limtis in r8169, from Igor Maravic.
8) Outline code intended for IP_RECVTOS in IP_PKTOPTIONS existed but
was never properly implemented, Jiri Benc fixed that.
9) 64-bit statistics support in r8169 and 8139too, from Junchang Wang.
10) Support kernel side dump filtering by ctmark in netfilter
ctnetlink, from Pablo Neira Ayuso.
11) Support byte-queue-limits in gianfar driver, from Paul Gortmaker.
12) Add new peek socket options to assist with socket migration, from
Pavel Emelyanov.
13) Add sch_plug packet scheduler whose queue is controlled by
userland daemons using explicit freeze and release commands. From
Shriram Rajagopalan.
14) Fix FCOE checksum offload handling on transmit, from Yi Zou."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1846 commits)
Fix pppol2tp getsockname()
Remove printk from rds_sendmsg
ipv6: fix incorrent ipv6 ipsec packet fragment
cpsw: Hook up default ndo_change_mtu.
net: qmi_wwan: fix build error due to cdc-wdm dependecy
netdev: driver: ethernet: Add TI CPSW driver
netdev: driver: ethernet: add cpsw address lookup engine support
phy: add am79c874 PHY support
mlx4_core: fix race on comm channel
bonding: send igmp report for its master
fs_enet: Add MPC5125 FEC support and PHY interface selection
net: bpf_jit: fix BPF_S_LDX_B_MSH compilation
net: update the usage of CHECKSUM_UNNECESSARY
fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx
net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso
ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
net/hyperv: Fix the code handling tx busy
ixgbe: fix namespace issues when FCoE/DCB is not enabled
rtlwifi: Remove unused ETH_ADDR_LEN defines
igbvf: Use ETH_ALEN
...
Fix up fairly trivial conflicts in drivers/isdn/gigaset/interface.c and
drivers/net/usb/{Kconfig,qmi_wwan.c} as per David.
There is no 2.4 GHz or 5GHz antenna gain stored in sprom. The sprom
just stores the gain values for antenna 1 and 2 or 1 to 4 for more
recent sprom versions. On old devices antenna 2 was used for 5 GHz wifi.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support the the BCM5354 SoC.
It has a PMU and a constant not configurable clock.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes us see what type of hardware someone uses by the dmesg
output.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb supports one extra device on the cardbus. This results in two
devices in total, one beeing the host controller itself and the other
the external device connected to the hostcontroller over cardbus.
This makes the cardbus slot work on the Linksys WRT150N.
Reported-by: Aaron Z <aaronz@pls-net.org>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As part of the removal of get_driver()/put_driver(), this patch
(as1512) gets rid of various useless and unnecessary calls in several
drivers. In some cases it may be desirable to pin the driver by
calling try_module_get(), but that can be done later.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: "David S. Miller" <davem@davemloft.net>
CC: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Michael Buesch <m@bues.ch>
CC: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We already extract some basic info but it's incomplete, reads info
about the first core only. Used data structure doesn't allow easy
adding of more cores.
This patch adds new struct and array for storing power info. The plan
is to: switch all extractors (including the ones using NVRAM) to new
struct, switch drivers, then deprecate and finally drop old SSB fields.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a Data bus error on some SoCs. The first fix for this
problem did not solve it on all devices.
commit 6ae8ec2786
Author: Rafał Miłecki <zajec5@gmail.com>
Date: Tue Jul 5 17:25:32 2011 +0200
ssb: fix init regression of hostmode PCI core
In ssb_pcicore_fix_sprom_core_index() the sprom on the PCI core is
accessed, but the sprom only exists when the ssb bus is connected over
a PCI bus to the rest of the system and not when the SSB Bus is the
main system bus. SoCs sometimes have a PCI host controller and there
this code will not be executed, but there are some old SoCs with an PCI
controller in client mode around and ssb_pcicore_fix_sprom_core_index()
should not be called on these devices too. The PCI controller on these
devices are unused, but without this fix it results in an Data bus
error when it gets initialized.
Cc: Michael Buesch <m@bues.ch>
Cc: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Or we will get things like this when we remove the implicit path:
drivers/ssb/embedded.c:32: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/ssb/driver_chipcommon.c:432: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/ssb/driver_chipcommon_pmu.c:607: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
drivers/ssb/pcihost_wrapper.c:120: error: ‘THIS_MODULE’ undeclared (first use in this function)
drivers/ssb/driver_pcicore.c:721: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/ssb/driver_gige.c:249: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The header cleanup means that module.h is no longer simply
everywhere. So real modules need to actively include it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
Remove b43's workarounds at the same time. Other users of
ssb_dma_translation do not support any 64-bit DMA devices, so they are
not affected.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI revision ID from the PCI configuration register while
it's already stored by the PCI subsystem in the 'revision' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SSB code reads PCI revision ID register as 16-bit entity while the register
is actually 8-bit only (the next 8 bits are the programming interface register).
Fix the read and make the 'rev' field of 'struct ssb_boardinfo' 8-bit as well,
to match the register size.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bus scan code reads PCI revision ID from the PCI configuration register
while it's already stored by PCI subsystem in the 'revision' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Greg Kroah-Hartman