Register our DRHD IOMMUs, cross link devices, and provide a base set
of attributes for the IOMMU. Note that IRQ remapping support parses
the DMAR table very early in boot, well before the iommu_class can
reasonably be setup, so our registration is split between
intel_iommu_init(), which occurs later, and alloc_iommu(), which
typically occurs much earlier, but may happen at any time later
with IOMMU hot-add support.
On a typical desktop system, this provides the following (pruned):
$ find /sys | grep dmar
/sys/devices/virtual/iommu/dmar0
/sys/devices/virtual/iommu/dmar0/devices
/sys/devices/virtual/iommu/dmar0/devices/0000:00:02.0
/sys/devices/virtual/iommu/dmar0/intel-iommu
/sys/devices/virtual/iommu/dmar0/intel-iommu/cap
/sys/devices/virtual/iommu/dmar0/intel-iommu/ecap
/sys/devices/virtual/iommu/dmar0/intel-iommu/address
/sys/devices/virtual/iommu/dmar0/intel-iommu/version
/sys/devices/virtual/iommu/dmar1
/sys/devices/virtual/iommu/dmar1/devices
/sys/devices/virtual/iommu/dmar1/devices/0000:00:00.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:01.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:16.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:1a.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:1b.0
/sys/devices/virtual/iommu/dmar1/devices/0000:00:1c.0
...
/sys/devices/virtual/iommu/dmar1/intel-iommu
/sys/devices/virtual/iommu/dmar1/intel-iommu/cap
/sys/devices/virtual/iommu/dmar1/intel-iommu/ecap
/sys/devices/virtual/iommu/dmar1/intel-iommu/address
/sys/devices/virtual/iommu/dmar1/intel-iommu/version
/sys/class/iommu/dmar0
/sys/class/iommu/dmar1
(devices also link back to the dmar units)
This makes address, version, capabilities, and extended capabilities
available, just like printed on boot. I've tried not to duplicate
data that can be found in the DMAR table, with the exception of the
address, which provides an easy way to associate the sysfs device with
a DRHD entry in the DMAR. It's tempting to add scopes and RMRR data
here, but the full DMAR table is already exposed under /sys/firmware/
and therefore already provides a way for userspace to learn such
details.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
IOMMUs currently have no common representation to userspace, most
seem to have no representation at all aside from a few printks
on bootup. There are however features of IOMMUs that are useful
to know about. For instance the IOMMU might support superpages,
making use of processor large/huge pages more important in a device
assignment scenario. It's also useful to create cross links between
devices and IOMMU hardware units, so that users might be able to
load balance their devices to avoid thrashing a single hardware unit.
This patch adds a device create and destroy interface as well as
device linking, making it very lightweight for an IOMMU driver to add
basic support. IOMMU drivers can provide additional attributes
automatically by using an attribute_group.
The attributes exposed are expected to be relatively device specific,
the means to retrieve them certainly are, so there are currently no
common attributes for the new class created here.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Move led_mode attribute from HID device to led-class devices and
rename it mode. This will also fix race condition by using
attribute-groups.
(cooloney@gmai.com: fix a typo in commit message)
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This driver adds support for USB controlled led panels that exists in
MSI GT683R laptop
Signed-off-by: Janne Kanniainen <janne.kanniainen@gmail.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
New drivers
* t5403 barometric pressure sensor
* kxcjk1013 accelerometer (with a locking followup fix).
* ak09911 digital compass
Documentation
* ABI docs for proximity added (interface has been there a long time but
somehow snuck through without being documented)
* Move iio-trig-sysfs documentation out of staging (got left behind when
the driver moved some time ago).
Cleanups
* drop the timestamp argument from iio_trigger_poll(_chained) as
nothing has been done with it for some time.
* ad799x kerneldoc for ad799x_chip brought up to date.
* replace a number of reimplementations of the GENMASK macro and
use the BIT macro to cleanup a few locations.
* bring the iio_event_monitor example program up to date with new
device types.
* fix some incorrect function prototypes in iio_utils.h example code.
* INDIO_RING_TRIGGERED to INDIO_BUFFER_TRIGGERED fix in docs. This
got left behind after we renamed it a long time back.
* fix error handling in the generic_buffer example program.
* small tidy ups in the iio-trig-periodic-rtc driver.
* Allow reseting iio-trig-periodic-rtc frequency to 0 (default) after
it has changed.
* Trivial tidy ups in coding style in iio_simply_dummy
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S0CY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.17a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, cleanups and functionality for the 3.17 cycle.
New drivers
* t5403 barometric pressure sensor
* kxcjk1013 accelerometer (with a locking followup fix).
* ak09911 digital compass
Documentation
* ABI docs for proximity added (interface has been there a long time but
somehow snuck through without being documented)
* Move iio-trig-sysfs documentation out of staging (got left behind when
the driver moved some time ago).
Cleanups
* drop the timestamp argument from iio_trigger_poll(_chained) as
nothing has been done with it for some time.
* ad799x kerneldoc for ad799x_chip brought up to date.
* replace a number of reimplementations of the GENMASK macro and
use the BIT macro to cleanup a few locations.
* bring the iio_event_monitor example program up to date with new
device types.
* fix some incorrect function prototypes in iio_utils.h example code.
* INDIO_RING_TRIGGERED to INDIO_BUFFER_TRIGGERED fix in docs. This
got left behind after we renamed it a long time back.
* fix error handling in the generic_buffer example program.
* small tidy ups in the iio-trig-periodic-rtc driver.
* Allow reseting iio-trig-periodic-rtc frequency to 0 (default) after
it has changed.
* Trivial tidy ups in coding style in iio_simply_dummy
iio-trig-sysfs has left staging with commit e64e7d5c
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
Pull powerpc updates from Ben Herrenschmidt:
"Here is the bulk of the powerpc changes for this merge window. It got
a bit delayed in part because I wasn't paying attention, and in part
because I discovered I had a core PCI change without a PCI maintainer
ack in it. Bjorn eventually agreed it was ok to merge it though we'll
probably improve it later and I didn't want to rebase to add his ack.
There is going to be a bit more next week, essentially fixes that I
still want to sort through and test.
The biggest item this time is the support to build the ppc64 LE kernel
with our new v2 ABI. We previously supported v2 userspace but the
kernel itself was a tougher nut to crack. This is now sorted mostly
thanks to Anton and Rusty.
We also have a fairly big series from Cedric that add support for
64-bit LE zImage boot wrapper. This was made harder by the fact that
traditionally our zImage wrapper was always 32-bit, but our new LE
toolchains don't really support 32-bit anymore (it's somewhat there
but not really "supported") so we didn't want to rely on it. This
meant more churn that just endian fixes.
This brings some more LE bits as well, such as the ability to run in
LE mode without a hypervisor (ie. under OPAL firmware) by doing the
right OPAL call to reinitialize the CPU to take HV interrupts in the
right mode and the usual pile of endian fixes.
There's another series from Gavin adding EEH improvements (one day we
*will* have a release with less than 20 EEH patches, I promise!).
Another highlight is the support for the "Split core" functionality on
P8 by Michael. This allows a P8 core to be split into "sub cores" of
4 threads which allows the subcores to run different guests under KVM
(the HW still doesn't support a partition per thread).
And then the usual misc bits and fixes ..."
[ Further delayed by gmail deciding that BenH is a dirty spammer.
Google knows. ]
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (155 commits)
powerpc/powernv: Add missing include to LPC code
selftests/powerpc: Test the THP bug we fixed in the previous commit
powerpc/mm: Check paca psize is up to date for huge mappings
powerpc/powernv: Pass buffer size to OPAL validate flash call
powerpc/pseries: hcall functions are exported to modules, need _GLOBAL_TOC()
powerpc: Exported functions __clear_user and copy_page use r2 so need _GLOBAL_TOC()
powerpc/powernv: Set memory_block_size_bytes to 256MB
powerpc: Allow ppc_md platform hook to override memory_block_size_bytes
powerpc/powernv: Fix endian issues in memory error handling code
powerpc/eeh: Skip eeh sysfs when eeh is disabled
powerpc: 64bit sendfile is capped at 2GB
powerpc/powernv: Provide debugfs access to the LPC bus via OPAL
powerpc/serial: Use saner flags when creating legacy ports
powerpc: Add cpu family documentation
powerpc/xmon: Fix up xmon format strings
powerpc/powernv: Add calls to support little endian host
powerpc: Document sysfs DSCR interface
powerpc: Fix regression of per-CPU DSCR setting
powerpc: Split __SYSFS_SPRSETUP macro
arch: powerpc/fadump: Cleaning up inconsistent NULL checks
...
Pull security layer updates from Serge Hallyn:
"This is a merge of James Morris' security-next tree from 3.14 to
yesterday's master, plus four patches from Paul Moore which are in
linux-next, plus one patch from Mimi"
* 'serge-next-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux-security:
ima: audit log files opened with O_DIRECT flag
selinux: conditionally reschedule in hashtab_insert while loading selinux policy
selinux: conditionally reschedule in mls_convert_context while loading selinux policy
selinux: reject setexeccon() on MNT_NOSUID applications with -EACCES
selinux: Report permissive mode in avc: denied messages.
Warning in scanf string typing
Smack: Label cgroup files for systemd
Smack: Verify read access on file open - v3
security: Convert use of typedef ctl_table to struct ctl_table
Smack: bidirectional UDS connect check
Smack: Correctly remove SMACK64TRANSMUTE attribute
SMACK: Fix handling value==NULL in post setxattr
bugfix patch for SMACK
Smack: adds smackfs/ptrace interface
Smack: unify all ptrace accesses in the smack
Smack: fix the subject/object order in smack_ptrace_traceme()
Minor improvement of 'smack_sb_kern_mount'
smack: fix key permission verification
KEYS: Move the flags representing required permission to linux/key.h
- ACPICA update to upstream version 20140424. That includes a
number of fixes and improvements related to things like GPE
handling, table loading, headers, memory mapping and unmapping,
DSDT/SSDT overriding, and the Unload() operator. The acpidump
utility from upstream ACPICA is included too. From Bob Moore,
Lv Zheng, David Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices
rather than PNP devices for ACPI device objects with _HID by
default. PNP devices will still be created for the ACPI device
object with device IDs corresponding to real PNP devices, so
that change should not break things left and right, and we're
expecting to see more and more ACPI-enumerated platform devices
in the future. From Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing
it to handle system suspend/resume on Asus T100 correctly.
From Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions
if certain additional conditions related to coordination within
device hierarchy are met. Related PM documentation update and
ACPI PM domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling,
Tony Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from
Chander Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie,
Doug Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from
Jacob Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way
from Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tpdF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm into next
Pull ACPI and power management updates from Rafael Wysocki:
"ACPICA is the leader this time (63 commits), followed by cpufreq (28
commits), devfreq (15 commits), system suspend/hibernation (12
commits), ACPI video and ACPI device enumeration (10 commits each).
We have no major new features this time, but there are a few
significant changes of how things work. The most visible one will
probably be that we are now going to create platform devices rather
than PNP devices by default for ACPI device objects with _HID. That
was long overdue and will be really necessary to be able to use the
same drivers for the same hardware blocks on ACPI and DT-based systems
going forward. We're not expecting fallout from this one (as usual),
but it's something to watch nevertheless.
The second change having a chance to be visible is that ACPI video
will now default to using native backlight rather than the ACPI
backlight interface which should generally help systems with broken
Win8 BIOSes. We're hoping that all problems with the native backlight
handling that we had previously have been addressed and we are in a
good enough shape to flip the default, but this change should be easy
enough to revert if need be.
In addition to that, the system suspend core has a new mechanism to
allow runtime-suspended devices to stay suspended throughout system
suspend/resume transitions if some extra conditions are met
(generally, they are related to coordination within device hierarchy).
However, enabling this feature requires cooperation from the bus type
layer and for now it has only been implemented for the ACPI PM domain
(used by ACPI-enumerated platform devices mostly today).
Also, the acpidump utility that was previously shipped as a separate
tool will now be provided by the upstream ACPICA along with the rest
of ACPICA code, which will allow it to be more up to date and better
supported, and we have one new cpuidle driver (ARM clps711x).
The rest is improvements related to certain specific use cases,
cleanups and fixes all over the place.
Specifics:
- ACPICA update to upstream version 20140424. That includes a number
of fixes and improvements related to things like GPE handling,
table loading, headers, memory mapping and unmapping, DSDT/SSDT
overriding, and the Unload() operator. The acpidump utility from
upstream ACPICA is included too. From Bob Moore, Lv Zheng, David
Box, David Binderman, and Colin Ian King.
- Fixes and cleanups related to ACPI video and backlight interfaces
from Hans de Goede. That includes blacklist entries for some new
machines and using native backlight by default.
- ACPI device enumeration changes to create platform devices rather
than PNP devices for ACPI device objects with _HID by default. PNP
devices will still be created for the ACPI device object with
device IDs corresponding to real PNP devices, so that change should
not break things left and right, and we're expecting to see more
and more ACPI-enumerated platform devices in the future. From
Zhang Rui and Rafael J Wysocki.
- Updates for the ACPI LPSS (Low-Power Subsystem) driver allowing it
to handle system suspend/resume on Asus T100 correctly. From
Heikki Krogerus and Rafael J Wysocki.
- PM core update introducing a mechanism to allow runtime-suspended
devices to stay suspended over system suspend/resume transitions if
certain additional conditions related to coordination within device
hierarchy are met. Related PM documentation update and ACPI PM
domain support for the new feature. From Rafael J Wysocki.
- Fixes and improvements related to the "freeze" sleep state. They
affect several places including cpuidle, PM core, ACPI core, and
the ACPI battery driver. From Rafael J Wysocki and Zhang Rui.
- Miscellaneous fixes and updates of the ACPI core from Aaron Lu,
Bjørn Mork, Hanjun Guo, Lan Tianyu, and Rafael J Wysocki.
- Fixes and cleanups for the ACPI processor and ACPI PAD (Processor
Aggregator Device) drivers from Baoquan He, Manuel Schölling, Tony
Camuso, and Toshi Kani.
- System suspend/resume optimization in the ACPI battery driver from
Lan Tianyu.
- OPP (Operating Performance Points) subsystem updates from Chander
Kashyap, Mark Brown, and Nishanth Menon.
- cpufreq core fixes, updates and cleanups from Srivatsa S Bhat,
Stratos Karafotis, and Viresh Kumar.
- Updates, fixes and cleanups for the Tegra, powernow-k8, imx6q,
s5pv210, nforce2, and powernv cpufreq drivers from Brian Norris,
Jingoo Han, Paul Bolle, Philipp Zabel, Stratos Karafotis, and
Viresh Kumar.
- intel_pstate driver fixes and cleanups from Dirk Brandewie, Doug
Smythies, and Stratos Karafotis.
- Enabling the big.LITTLE cpufreq driver on arm64 from Mark Brown.
- Fix for the cpuidle menu governor from Chander Kashyap.
- New ARM clps711x cpuidle driver from Alexander Shiyan.
- Hibernate core fixes and cleanups from Chen Gang, Dan Carpenter,
Fabian Frederick, Pali Rohár, and Sebastian Capella.
- Intel RAPL (Running Average Power Limit) driver updates from Jacob
Pan.
- PNP subsystem updates from Bjorn Helgaas and Fabian Frederick.
- devfreq core updates from Chanwoo Choi and Paul Bolle.
- devfreq updates for exynos4 and exynos5 from Chanwoo Choi and
Bartlomiej Zolnierkiewicz.
- turbostat tool fix from Jean Delvare.
- cpupower tool updates from Prarit Bhargava, Ramkumar Ramachandra
and Thomas Renninger.
- New ACPI ec_access.c tool for poking at the EC in a safe way from
Thomas Renninger"
* tag 'pm+acpi-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (187 commits)
ACPICA: Namespace: Remove _PRP method support.
intel_pstate: Improve initial busy calculation
intel_pstate: add sample time scaling
intel_pstate: Correct rounding in busy calculation
intel_pstate: Remove C0 tracking
PM / hibernate: fixed typo in comment
ACPI: Fix x86 regression related to early mapping size limitation
ACPICA: Tables: Add mechanism to control early table checksum verification.
ACPI / scan: use platform bus type by default for _HID enumeration
ACPI / scan: always register ACPI LPSS scan handler
ACPI / scan: always register memory hotplug scan handler
ACPI / scan: always register container scan handler
ACPI / scan: Change the meaning of missing .attach() in scan handlers
ACPI / scan: introduce platform_id device PNP type flag
ACPI / scan: drop unsupported serial IDs from PNP ACPI scan handler ID list
ACPI / scan: drop IDs that do not comply with the ACPI PNP ID rule
ACPI / PNP: use device ID list for PNPACPI device enumeration
ACPI / scan: .match() callback for ACPI scan handlers
ACPI / battery: wakeup the system only when necessary
power_supply: allow power supply devices registered w/o wakeup source
...
Pull HID patches from Jiri Kosina:
- RMI driver for Synaptics touchpads, by Benjamin Tissoires, Andrew
Duggan and Jiri Kosina
- cleanup of hid-sony driver and improved support for Sixaxis and
Dualshock 4, by Frank Praznik
- other usual small fixes and support for new device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (29 commits)
HID: thingm: thingm_fwinfo[] doesn't need to be global
HID: core: add two new usages for digitizer
HID: hid-sensor-hub: new device id and quirk for STM Sensor hub
HID: usbhid: enable NO_INIT_REPORTS quirk for Semico USB Keykoard
HID: hid-sensor-hub: Set report quirk for Microsoft Surface
HID: debug: add labels for HID Sensor Usages
HID: uhid: Use kmemdup instead of kmalloc + memcpy
HID: rmi: do not handle touchscreens through hid-rmi
HID: quirk for Saitek RAT7 and MMO7 mices' mode button
HID: core: fix validation of report id 0
HID: rmi: fix masks for x and w_x data
HID: rmi: fix wrong struct field name
HID: rmi: do not fetch more than 16 bytes in a query
HID: rmi: check for the existence of some optional queries before reading query 12
HID: i2c-hid: hid report descriptor retrieval changes
HID: add missing hid usages
HID: hid-sony - allow 3rd party INTEC controller to turn off all leds
HID: sony: Add blink support to the Sixaxis and DualShock 4 LEDs
HID: sony: Initialize the controller LEDs with a device ID value
HID: sony: Use the controller Bluetooth MAC address as the unique value in the battery name string
...
* pm-cpufreq: (28 commits)
cpufreq: handle calls to ->target_index() in separate routine
cpufreq: s5pv210: drop check for CONFIG_PM_VERBOSE
cpufreq: intel_pstate: Remove unused member name of cpudata
cpufreq: Break out early when frequency equals target_freq
cpufreq: Tegra: drop wrapper around tegra_update_cpu_speed()
cpufreq: imx6q: Remove unused include
cpufreq: imx6q: Drop devm_clk/regulator_get usage
cpufreq: powernow-k8: Suppress checkpatch warnings
cpufreq: powernv: make local function static
cpufreq: Enable big.LITTLE cpufreq driver on arm64
cpufreq: nforce2: remove DEFINE_PCI_DEVICE_TABLE macro
intel_pstate: Add CPU IDs for Broadwell processors
cpufreq: Fix build error on some platforms that use cpufreq_for_each_*
PM / OPP: Move cpufreq specific OPP functions out of generic OPP library
PM / OPP: Remove cpufreq wrapper dependency on internal data organization
cpufreq: Catch double invocations of cpufreq_freq_transition_begin/end
intel_pstate: Remove sample parameter in intel_pstate_calc_busy
cpufreq: Kconfig: Fix spelling errors
cpufreq: Make linux-pm@vger.kernel.org official mailing list
cpufreq: exynos: Use dev_err/info function instead of pr_err/info
...
* pm-sleep:
PM / hibernate: fixed typo in comment
PM / sleep: unregister wakeup source when disabling device wakeup
PM / sleep: Introduce command line argument for sleep state enumeration
PM / sleep: Use valid_state() for platform-dependent sleep states only
PM / sleep: Add state field to pm_states[] entries
PM / sleep: Update device PM documentation to cover direct_complete
PM / sleep: Mechanism to avoid resuming runtime-suspended devices unnecessarily
PM / hibernate: Fix memory corruption in resumedelay_setup()
PM / hibernate: convert simple_strtoul to kstrtoul
PM / hibernate: Documentation: Fix script for unswapping
PM / hibernate: no kernel_power_off when pm_power_off NULL
PM / hibernate: use unsigned local variables in swsusp_show_speed()
Files are measured or appraised based on the IMA policy. When a
file, in policy, is opened with the O_DIRECT flag, a deadlock
occurs.
The first attempt at resolving this lockdep temporarily removed the
O_DIRECT flag and restored it, after calculating the hash. The
second attempt introduced the O_DIRECT_HAVELOCK flag. Based on this
flag, do_blockdev_direct_IO() would skip taking the i_mutex a second
time. The third attempt, by Dmitry Kasatkin, resolves the i_mutex
locking issue, by re-introducing the IMA mutex, but uncovered
another problem. Reading a file with O_DIRECT flag set, writes
directly to userspace pages. A second patch allocates a user-space
like memory. This works for all IMA hooks, except ima_file_free(),
which is called on __fput() to recalculate the file hash.
Until this last issue is addressed, do not 'collect' the
measurement for measuring, appraising, or auditing files opened
with the O_DIRECT flag set. Based on policy, permit or deny file
access. This patch defines a new IMA policy rule option named
'permit_directio'. Policy rules could be defined, based on LSM
or other criteria, to permit specific applications to open files
with the O_DIRECT flag set.
Changelog v1:
- permit or deny file access based IMA policy rules
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: Dmitry Kasatkin <d.kasatkin@samsung.com>
Cc: <stable@vger.kernel.org>
Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work better
now that it has been reworked to do per-port power control dynamically.
There's also a raft of gadget driver updates and fixes, CONFIG_USB_DEBUG
is finally gone now that everything has been converted over to the
dynamic debug inteface, the last hold-out drivers were cleaned up and
the config option removed. There were also other minor things all
through the drivers/usb/ tree, the shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONYEMACgkQMUfUDdst+ynxvgCggMQBhN5icth8Y5hFglNNaISN
c4AAoMHR2kb62U1plylLbPnboQTjfcl0
=fG6y
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb into next
Pull USB driver updates from Greg KH:
"Here is the big USB driver pull request for 3.16-rc1.
Nothing huge here, but lots of little things in the USB core, and in
lots of drivers. Hopefully the USB power management will be work
better now that it has been reworked to do per-port power control
dynamically. There's also a raft of gadget driver updates and fixes,
CONFIG_USB_DEBUG is finally gone now that everything has been
converted over to the dynamic debug inteface, the last hold-out
drivers were cleaned up and the config option removed. There were
also other minor things all through the drivers/usb/ tree, the
shortlog shows this pretty well.
All have been in linux-next, including the very last patch, which came
from linux-next to fix a build issue on some platforms"
* tag 'usb-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (314 commits)
usb: hub_handle_remote_wakeup() only exists for CONFIG_PM=y
USB: orinoco_usb: remove CONFIG_USB_DEBUG support
USB: media: lirc: igorplugusb: remove CONFIG_USB_DEBUG support
USB: media: streamzap: remove CONFIG_USB_DEBUG
USB: media: redrat3: remove CONFIG_USB_DEBUG usage
USB: media: redrat3: remove unneeded tracing macro
usb: qcserial: add additional Sierra Wireless QMI devices
usb: host: max3421-hcd: Use module_spi_driver
usb: host: max3421-hcd: Allow platform-data to specify Vbus polarity
usb: host: max3421-hcd: fix "spi_rd8" uses dynamic stack allocation warning
usb: host: max3421-hcd: Fix missing unlock in max3421_urb_enqueue()
usb: qcserial: add Netgear AirCard 341U
Documentation: dt-bindings: update xhci-platform DT binding for R-Car H2 and M2
usb: host: xhci-plat: add xhci_plat_start()
usb: host: max3421-hcd: Fix potential NULL urb dereference
Revert "usb: gadget: net2280: Add support for PLX USB338X"
USB: usbip: remove CONFIG_USB_DEBUG reference
USB: remove CONFIG_USB_DEBUG from defconfig files
usb: resume child device when port is powered on
usb: hub_handle_remote_wakeup() depends on CONFIG_PM_RUNTIME=y
...
Here is the big staging driver pull request for 3.16-rc1.
Lots of stuff here, tons of cleanup patches, a few new drivers, and some
removed as well, but I think we are still adding a few thousand more
lines than we remove, due to the new drivers being bigger than the ones
deleted.
One notible bit of work did stand out, Jes Sorensen has gone on a tear,
fixing up a wireless driver to be "more sane" than it originally was
from the vendor, with over 500 patches merged here. Good stuff, and a
number of users laptops are better off for it.
All of this has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONXKQACgkQMUfUDdst+ynIwgCgq5pPIn+2aewaFK8rrN18xqls
F3YAoNDYeqMpQepvRe50HcjRrgDvsV2n
=VenO
-----END PGP SIGNATURE-----
Merge tag 'staging-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging into next
Pull staging driver updates from Greg KH:
"Here is the big staging driver pull request for 3.16-rc1.
Lots of stuff here, tons of cleanup patches, a few new drivers, and
some removed as well, but I think we are still adding a few thousand
more lines than we remove, due to the new drivers being bigger than
the ones deleted.
One notible bit of work did stand out, Jes Sorensen has gone on a
tear, fixing up a wireless driver to be "more sane" than it originally
was from the vendor, with over 500 patches merged here. Good stuff,
and a number of users laptops are better off for it.
All of this has been in linux-next for a while"
* tag 'staging-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1703 commits)
staging: skein: fix sparse warning for static declarations
staging/mt29f_spinand: coding style fixes
staging: silicom: fix sparse warning for static variable
staging: lustre: Fix coding style
staging: android: binder.c: Use more appropriate functions for euid retrieval
staging: lustre: fix integer as NULL pointer warnings
Revert "staging: dgap: remove unneeded kfree() in dgap_tty_register_ports()"
Staging: rtl8192u: r8192U_wx.c Fixed a misplaced brace
staging: ion: shrink highmem pages on kswapd
staging: ion: use compound pages on high order pages for system heap
staging: ion: remove struct ion_page_pool_item
staging: ion: simplify ion_page_pool_total()
staging: ion: tidy up a bit
staging: rtl8723au: Remove redundant casting in usb_ops_linux.c
staging: rtl8723au: Remove redundant casting in rtl8723a_hal_init.c
staging: rtl8723au: Remove redundant casting in rtw_xmit.c
staging: rtl8723au: Remove redundant casting in rtw_wlan_util.c
staging: rtl8723au: Remove redundant casting in rtw_sta_mgt.c
staging: rtl8723au: Remove redundant casting in rtw_recv.c
staging: rtl8723au: Remove redundant casting in rtw_mlme.c
...
SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing lists),
we are here adding a drivers/soc directory. The purpose of this is
to keep per-vendor shared code that's needed by different drivers but
that doesn't fit into the MFD (nor drivers/platform) model. We expect
to keep merging contents for this hierarchy through arm-soc so we can
keep an eye on what the vendors keep adding here and not making it a
free-for-all to shove in crazy stuff.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=SC+e
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull ARM SoC driver changes from Olof Johansson:
"SoC-near driver changes that we're merging through our tree. Mostly
because they depend on other changes we have staged, but in some cases
because the driver maintainers preferred that we did it this way.
This contains a largeish cleanup series of the omap_l3_noc bus driver,
cpuidle rework for Exynos, some reset driver conversions and a long
branch of TI EDMA fixes and cleanups, with more to come next release.
The TI EDMA cleanups is a shared branch with the dmaengine tree, with
a handful of Davinci-specific fixes on top.
After discussion at last year's KS (and some more on the mailing
lists), we are here adding a drivers/soc directory. The purpose of
this is to keep per-vendor shared code that's needed by different
drivers but that doesn't fit into the MFD (nor drivers/platform)
model. We expect to keep merging contents for this hierarchy through
arm-soc so we can keep an eye on what the vendors keep adding here and
not making it a free-for-all to shove in crazy stuff"
* tag 'drivers-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (101 commits)
cpufreq: exynos: Fix driver compilation with ARCH_MULTIPLATFORM
tty: serial: msm: Remove direct access to GSBI
power: reset: keystone-reset: introduce keystone reset driver
Documentation: dt: add bindings for keystone pll control controller
Documentation: dt: add bindings for keystone reset driver
soc: qcom: fix of_device_id table
ARM: EXYNOS: Fix kernel panic when unplugging CPU1 on exynos
ARM: EXYNOS: Move the driver to drivers/cpuidle directory
ARM: EXYNOS: Cleanup all unneeded headers from cpuidle.c
ARM: EXYNOS: Pass the AFTR callback to the platform_data
ARM: EXYNOS: Move S5P_CHECK_SLEEP into pm.c
ARM: EXYNOS: Move the power sequence call in the cpu_pm notifier
ARM: EXYNOS: Move the AFTR state function into pm.c
ARM: EXYNOS: Encapsulate the AFTR code into a function
ARM: EXYNOS: Disable cpuidle for exynos5440
ARM: EXYNOS: Encapsulate boot vector code into a function for cpuidle
ARM: EXYNOS: Pass wakeup mask parameter to function for cpuidle
ARM: EXYNOS: Remove ifdef for scu_enable in pm
ARM: EXYNOS: Move scu_enable in the cpu_pm notifier
ARM: EXYNOS: Use the cpu_pm notifier for pm
...
Adding documentation for all the driver specific sysfs attributes.
Cc: Peter Stuge <peter@stuge.se>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
has been in use for a long time, but never documented
proximity is unit-less, except otherwise stated, see e.g.
the as3935 driver where it is meter
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* pci/hotplug:
PCI: cpqphp: Fix possible null pointer dereference
NVMe: Implement PCIe reset notification callback
PCI: Notify driver before and after device reset
* pci/pci_is_bridge:
pcmcia: Use pci_is_bridge() to simplify code
PCI: pciehp: Use pci_is_bridge() to simplify code
PCI: acpiphp: Use pci_is_bridge() to simplify code
PCI: cpcihp: Use pci_is_bridge() to simplify code
PCI: shpchp: Use pci_is_bridge() to simplify code
PCI: rpaphp: Use pci_is_bridge() to simplify code
sparc/PCI: Use pci_is_bridge() to simplify code
powerpc/PCI: Use pci_is_bridge() to simplify code
ia64/PCI: Use pci_is_bridge() to simplify code
x86/PCI: Use pci_is_bridge() to simplify code
PCI: Use pci_is_bridge() to simplify code
PCI: Add new pci_is_bridge() interface
PCI: Rename pci_is_bridge() to pci_has_subordinate()
* pci/virtualization:
PCI: Introduce new device binding path using pci_dev.driver_override
Conflicts:
drivers/pci/pci-sysfs.c
The driver_override field allows us to specify the driver for a device
rather than relying on the driver to provide a positive match of the
device. This shortcuts the existing process of looking up the vendor and
device ID, adding them to the driver new_id, binding the device, then
removing the ID, but it also provides a couple advantages.
First, the above existing process allows the driver to bind to any device
matching the new_id for the window where it's enabled. This is often not
desired, such as the case of trying to bind a single device to a meta
driver like pci-stub or vfio-pci. Using driver_override we can do this
deterministically using:
echo pci-stub > /sys/bus/pci/devices/0000:03:00.0/driver_override
echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
echo 0000:03:00.0 > /sys/bus/pci/drivers_probe
Previously we could not invoke drivers_probe after adding a device to
new_id for a driver as we get non-deterministic behavior whether the driver
we intend or the standard driver will claim the device. Now it becomes a
deterministic process, only the driver matching driver_override will probe
the device.
To return the device to the standard driver, we simply clear the
driver_override and reprobe the device:
echo > /sys/bus/pci/devices/0000:03:00.0/driver_override
echo 0000:03:00.0 > /sys/bus/pci/devices/0000:03:00.0/driver/unbind
echo 0000:03:00.0 > /sys/bus/pci/drivers_probe
Another advantage to this approach is that we can specify a driver override
to force a specific binding or prevent any binding. For instance when an
IOMMU group is exposed to userspace through VFIO we require that all
devices within that group are owned by VFIO. However, devices can be
hot-added into an IOMMU group, in which case we want to prevent the device
from binding to any driver (override driver = "none") or perhaps have it
automatically bind to vfio-pci. With driver_override it's a simple matter
for this field to be set internally when the device is first discovered to
prevent driver matches.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add some documentation about ...
/sys/devices/system/cpu/dscr_default
/sys/devices/system/cpu/cpuN/dscr
... to Documentation/ABI/stable.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On some systems the platform doesn't support neither
PM_SUSPEND_MEM nor PM_SUSPEND_STANDBY, so PM_SUSPEND_FREEZE is the
only available system sleep state. However, some user space frameworks
only use the "mem" and (sometimes) "standby" sleep state labels, so
the users of those systems need to modify user space in order to be
able to use system suspend at all and that is not always possible.
For this reason, add a new kernel command line argument,
relative_sleep_states, allowing the users of those systems to change
the way in which the kernel assigns labels to system sleep states.
Namely, for relative_sleep_states=1, the "mem", "standby" and "freeze"
labels will enumerate the available system sleem states from the
deepest to the shallowest, respectively, so that "mem" is always
present in /sys/power/state and the other state strings may or may
not be presend depending on what is supported by the platform.
Update system sleep states documentation to reflect this change.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Document the network device statistics counter that are exposed as sysfs
attributes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sysfs documentation for the various attributes of a network
interface exposed in /sys/class/<iface>/queues/{rx,tx}-<queue>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add documentation for the phys_port_id sysfs attribute of a network
device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch documents the sysfs properties exposed by the Broadcom GISB
bus arbiter hardware.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
This resolves the conflicts in the files:
drivers/iio/adc/Kconfig
drivers/staging/rtl8723au/os_dep/usb_ops_linux.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add handling of OS Extended Properties descriptors from configfs interface.
One kind of "OS Descriptors" are "Extended Properties" descriptors, which
need to be specified per interface or per group of interfaces described
by an IAD. This patch adds support for creating subdirectories
in interface.<n> directory located in the function's directory.
Names of subdirectories created become names of properties.
Each property contains two attributes: "type" and "data".
The type can be a numeric value 1..7 while data is a blob interpreted
depending on the type specified.
The types are:
1 - unicode string
2 - unicode string with environment variables
3 - binary
4 - little-endian 32-bit
5 - big-endian 32-bit
6 - unicode string with a symbolic link
7 - multiple unicode strings
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add handling of OS Extended Compatibility descriptors from configfs interface.
Hosts which expect the "OS Descriptors" ask only for configurations @ index 0,
but linux-based USB devices can provide more than one configuration.
This patch adds marking one of gadget's configurations the configuration
to be reported at index 0, regardless of the actual sequence of usb_add_config
invocations used for adding the configurations. The configuration is selected
by creating a symbolic link pointing to it from the "os_desc" directory
located at the top of a gadget's directory hierarchy.
One kind of "OS Descriptors" are "Extended Compatibility Descriptors",
which need to be specified per interface. This patch adds interface.<n>
directory in function's configfs directory to represent each interface
defined by the function. Each interface's directory contains two attributes:
"compatible_id" and "sub_compatible_id", which represent 8-byte
strings to be reported to the host as the "Compatible ID" and "Sub Compatible
ID".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add handling of OS String extension from the configfs interface.
A directory "os_desc" is added at the top level of a gadget's
directories hierarchy. In the "os_desc" directory there are
three attributes: "use", "b_vendor_code" and "qw_sign".
If "use" contains "0" the OS string is not reported to the host.
"b_vendor_code" contains a one-byte value which is used
for custom per-device and per-interface requests.
"qw_sign" contains an identifier to be reported as the "OS String"
proper.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
has been in use for a long time, but never documented;
state that this measurement should be in lux (drivers may feel
different about this)
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
intensity has been in use for a long time but never documented
it is beneficial to document what this is supposed to be
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There has been confusion all the time about which mailing list to follow
for cpufreq activities, linux-pm@vger.kernel.org or cpufreq@vger.kernel.org.
Since patches sent to cpufreq@vger.kernel.org don't go to Patchwork
which is a maintenance workflow problem, make linux-pm@vger.kernel.org
the official mailing list for cpufreq stuff and remove all references
of cpufreq@vger.kernel.org from kernel source.
Later, we can request that the list be dropped entirely.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Added documentation for reading quaternion components for 3D rotations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support
* AS3935 Lightning Sensor
* MCP3426/7/8 support added to the existing MCP3422 ADC driver
* AK8963 support in the AK8975 driver
* MPU6500 support in the MPU6050 driver (the functionality that is different
is mostly not supported yet in either part).
Staging Graduations
* AD799x ADC
New functionality
* ACPI enumeration for the ak8975 driver
Cleanup / tweaks
* Use snprintf as a matter of good practice in a few additional places.
* Document *_mean_raw attributes. These have been there a while, but were
undocumented.
* Add an in kernel interface to get the mean values.
* Bug in the length of the event info mask that by coincidence wasn't yet
actually causing any problems.
* itg3000 drop an unreachable return statement.
* spear_adc cleanups (heading for a staging graduation but a few more
issues showed up in the review of these patches).
* Exynos ADC dependencies changed so it is only built when Exynos is present
or COMPILE_TEST and OF are set.
* tsl2583 cleanups.
* Some cut and paste typos in the comments of various drivers still in staging.
* Couple of minor improvements to the ST sensor drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABAgAGBQJTW8asAAoJEFSFNJnE9BaITYoP/1rONn2PS1t61CI4rtWDVZh8
SEn4EQCxRVVAdWCQQz1zY0JZeUSjuWcPi7+MJ/VNaw6efOXN0J4O+bsNfh5Asju2
88giAUuP+hmd4xccGkxaJvdXEhruRMzGugh3/6+L2XuhkJsorAhJe/63XTq+JNOp
Tq6NHVmqV507wuDOguXfUQ2eDKPEFiTBUiutLJqyLOOi5zEq/X3Cnv+YMCDx4coE
BwZEQnXJWLfMSvXQtbTAl1XwqvDY8bjMNwFvjRuTLN73ua0/gMe//kJV/2tm8UMF
90Fs3TPi/cc5QkvpKMC9DP8eeAMi11bRdSRN0/abEQgglCz1LzWuX5Gqpr5psrhM
q1KS9JU9u4oZ8PR49c8QWjN0RtNiKiVVhCgBVcNE/2uYVwQqu0kJWylsq/m2+7jr
99qi8R979b5GoX69TKjVyr9MyGbN2x/vKWm3+UgtujqzXgu7GGdXa6NhrcPGcYjW
/uH3rfW4w0rBFVEJzDXkj74n/j2WDvrukjqYgABfENfBqO14swc0nlBGGyjli0uv
tUiwwS05Fax8wmuMP/wlII7Bq9XA8e+QISXHeO318svP/9SPxRuRwsd2Oo7BxXZz
e6gm5i142XeiSc3KjLGEUAZ+qF7xKUfEZwIajkWZ8LIgeROfDLzNEjvVsU2Byk+0
g+XrtWm4jljKHzjV/33g
=eqGz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.16a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new driver, functionality and cleanups for the 3.16 cycle.
New device support
* AS3935 Lightning Sensor
* MCP3426/7/8 support added to the existing MCP3422 ADC driver
* AK8963 support in the AK8975 driver
* MPU6500 support in the MPU6050 driver (the functionality that is different
is mostly not supported yet in either part).
Staging Graduations
* AD799x ADC
New functionality
* ACPI enumeration for the ak8975 driver
Cleanup / tweaks
* Use snprintf as a matter of good practice in a few additional places.
* Document *_mean_raw attributes. These have been there a while, but were
undocumented.
* Add an in kernel interface to get the mean values.
* Bug in the length of the event info mask that by coincidence wasn't yet
actually causing any problems.
* itg3000 drop an unreachable return statement.
* spear_adc cleanups (heading for a staging graduation but a few more
issues showed up in the review of these patches).
* Exynos ADC dependencies changed so it is only built when Exynos is present
or COMPILE_TEST and OF are set.
* tsl2583 cleanups.
* Some cut and paste typos in the comments of various drivers still in staging.
* Couple of minor improvements to the ST sensor drivers.
This patch adds sysfs interface description for chipidea USB OTG HNP and SRP.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch refactors the way the thingm driver registers a blink(1) LED.
In order to make the driver simpler and more standard, drop the "rgb"
sysfs attribute and create one instance of LED class per RGB channel.
Actually, the name of the LED class instance registered for a blink(1)
device is "blink1::ABCD", where ABCD is the last 4 chars of the serial
number. The driver now registers 3 instances per RGB chip, named
"thingmX:{red,green,blue}:ledY" where X is the hidraw minor number and Y
is the RGB chip number (as seen by the firmware).
This patch also uses work queues to defer calls with the device, which
now allows triggers to work as expected with this LED device.
Also remove the brightness structure field and the brightness_get
backend, as it is already handled by the LED class, and changes the
prefix of functions and structures to thingm_ to match the driver name.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
As for the "play" sysfs attribute, remove this other non-standard
attribute, so the driver only implements what is required to switch the
LED on and off. Thus, a fade time won't be ideal for some fast-changing
triggers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
When the thingm driver registers an instance of LED class, it creates a
"play" sysfs attribute for this blink(1) specific feature.
Since this feature is not specific to the RGB chip but to the HID device
itself, let's remove this attribute from the LED instance and only
implement what is useful to switch on and off the LED.
This feature is still easily accessible through hidraw.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target residency
information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen Chandler
Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan Choi,
Zhihui Zhang, Hanjun Guo.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hGKg
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management fixes and updates from Rafael Wysocki:
"This is PM and ACPI material that has emerged over the last two weeks
and one fix for a CPU hotplug regression introduced by the recent CPU
hotplug notifiers registration series.
Included are intel_idle and turbostat updates from Len Brown (these
have been in linux-next for quite some time), a new cpufreq driver for
powernv (that might spend some more time in linux-next, but BenH was
asking me so nicely to push it for 3.15 that I couldn't resist), some
cpufreq fixes and cleanups (including fixes for some silly breakage in
a couple of cpufreq drivers introduced during the 3.14 cycle),
assorted ACPI cleanups, wakeup framework documentation fixes, a new
sysfs attribute for cpuidle and a new command line argument for power
domains diagnostics.
Specifics:
- Fix for a recently introduced CPU hotplug regression in ARM KVM
from Ming Lei.
- Fixes for breakage in the at32ap, loongson2_cpufreq, and unicore32
cpufreq drivers introduced during the 3.14 cycle (-stable material)
from Chen Gang and Viresh Kumar.
- New powernv cpufreq driver from Vaidyanathan Srinivasan, with bits
from Gautham R Shenoy and Srivatsa S Bhat.
- Exynos cpufreq driver fix preventing it from being included into
multiplatform builds that aren't supported by it from Sachin Kamat.
- cpufreq cleanups related to the usage of the driver_data field in
struct cpufreq_frequency_table from Viresh Kumar.
- cpufreq ppc driver cleanup from Sachin Kamat.
- Intel BayTrail support for intel_idle and ACPI idle from Len Brown.
- Intel CPU model 54 (Atom N2000 series) support for intel_idle from
Jan Kiszka.
- intel_idle fix for Intel Ivy Town residency targets from Len Brown.
- turbostat updates (Intel Broadwell support and output cleanups)
from Len Brown.
- New cpuidle sysfs attribute for exporting C-states' target
residency information to user space from Daniel Lezcano.
- New kernel command line argument to prevent power domains enabled
by the bootloader from being turned off even if they are not in use
(for diagnostics purposes) from Tushar Behera.
- Fixes for wakeup sysfs attributes documentation from Geert
Uytterhoeven.
- New ACPI video blacklist entry for ThinkPad Helix from Stephen
Chandler Paul.
- Assorted ACPI cleanups and a Kconfig help update from Jonghwan
Choi, Zhihui Zhang, Hanjun Guo"
* tag 'pm+acpi-3.15-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (28 commits)
ACPI: Update the ACPI spec information in Kconfig
arm, kvm: fix double lock on cpu_add_remove_lock
cpuidle: sysfs: Export target residency information
cpufreq: ppc: Remove duplicate inclusion of fsl_soc.h
cpufreq: create another field .flags in cpufreq_frequency_table
cpufreq: use kzalloc() to allocate memory for cpufreq_frequency_table
cpufreq: don't print value of .driver_data from core
cpufreq: ia64: don't set .driver_data to index
cpufreq: powernv: Select CPUFreq related Kconfig options for powernv
cpufreq: powernv: Use cpufreq_frequency_table.driver_data to store pstate ids
cpufreq: powernv: cpufreq driver for powernv platform
cpufreq: at32ap: don't declare local variable as static
cpufreq: loongson2_cpufreq: don't declare local variable as static
cpufreq: unicore32: fix typo issue for 'clk'
cpufreq: exynos: Disable on multiplatform build
PM / wakeup: Correct presence vs. emptiness of wakeup_* attributes
PM / domains: Add pd_ignore_unused to keep power domains enabled
ACPI / dock: Drop dock_device_ids[] table
ACPI / video: Favor native backlight interface for ThinkPad Helix
ACPI / thermal: Fix wrong variable usage in debug statement
...
Merge second patch-bomb from Andrew Morton:
- the rest of MM
- zram updates
- zswap updates
- exit
- procfs
- exec
- wait
- crash dump
- lib/idr
- rapidio
- adfs, affs, bfs, ufs
- cris
- Kconfig things
- initramfs
- small amount of IPC material
- percpu enhancements
- early ioremap support
- various other misc things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (156 commits)
MAINTAINERS: update Intel C600 SAS driver maintainers
fs/ufs: remove unused ufs_super_block_third pointer
fs/ufs: remove unused ufs_super_block_second pointer
fs/ufs: remove unused ufs_super_block_first pointer
fs/ufs/super.c: add __init to init_inodecache()
doc/kernel-parameters.txt: add early_ioremap_debug
arm64: add early_ioremap support
arm64: initialize pgprot info earlier in boot
x86: use generic early_ioremap
mm: create generic early_ioremap() support
x86/mm: sparse warning fix for early_memremap
lglock: map to spinlock when !CONFIG_SMP
percpu: add preemption checks to __this_cpu ops
vmstat: use raw_cpu_ops to avoid false positives on preemption checks
slub: use raw_cpu_inc for incrementing statistics
net: replace __this_cpu_inc in route.c with raw_cpu_inc
modules: use raw_cpu_write for initialization of per cpu refcount.
mm: use raw_cpu ops for determining current NUMA node
percpu: add raw_cpu_ops
slub: fix leak of 'name' in sysfs_slab_add
...
Existing zram (zcomp) implementation has only one compression stream
(buffer and algorithm private part), so in order to prevent data
corruption only one write (compress operation) can use this compression
stream, forcing all concurrent write operations to wait for stream lock
to be released. This patch changes zcomp to keep a compression streams
list of user-defined size (via sysfs device attr). Each write operation
still exclusively holds compression stream, the difference is that we
can have N write operations (depending on size of streams list)
executing in parallel. See TEST section later in commit message for
performance data.
Introduce struct zcomp_strm_multi and a set of functions to manage
zcomp_strm stream access. zcomp_strm_multi has a list of idle
zcomp_strm structs, spinlock to protect idle list and wait queue, making
it possible to perform parallel compressions.
The following set of functions added:
- zcomp_strm_multi_find()/zcomp_strm_multi_release()
find and release a compression stream, implement required locking
- zcomp_strm_multi_create()/zcomp_strm_multi_destroy()
create and destroy zcomp_strm_multi
zcomp ->strm_find() and ->strm_release() callbacks are set during
initialisation to zcomp_strm_multi_find()/zcomp_strm_multi_release()
correspondingly.
Each time zcomp issues a zcomp_strm_multi_find() call, the following set
of operations performed:
- spin lock strm_lock
- if idle list is not empty, remove zcomp_strm from idle list, spin
unlock and return zcomp stream pointer to caller
- if idle list is empty, current adds itself to wait queue. it will be
awaken by zcomp_strm_multi_release() caller.
zcomp_strm_multi_release():
- spin lock strm_lock
- add zcomp stream to idle list
- spin unlock, wake up sleeper
Minchan Kim reported that spinlock-based locking scheme has demonstrated
a severe perfomance regression for single compression stream case,
comparing to mutex-based (see https://lkml.org/lkml/2014/2/18/16)
base spinlock mutex
==Initial write ==Initial write ==Initial write
records: 5 records: 5 records: 5
avg: 1642424.35 avg: 699610.40 avg: 1655583.71
std: 39890.95(2.43%) std: 232014.19(33.16%) std: 52293.96
max: 1690170.94 max: 1163473.45 max: 1697164.75
min: 1568669.52 min: 573429.88 min: 1553410.23
==Rewrite ==Rewrite ==Rewrite
records: 5 records: 5 records: 5
avg: 1611775.39 avg: 501406.64 avg: 1684419.11
std: 17144.58(1.06%) std: 15354.41(3.06%) std: 18367.42
max: 1641800.95 max: 531356.78 max: 1706445.84
min: 1593515.27 min: 488817.78 min: 1655335.73
When only one compression stream available, mutex with spin on owner
tends to perform much better than frequent wait_event()/wake_up(). This
is why single stream implemented as a special case with mutex locking.
Introduce and document zram device attribute max_comp_streams. This
attr shows and stores current zcomp's max number of zcomp streams
(max_strm). Extend zcomp's zcomp_create() with `max_strm' parameter.
`max_strm' limits the number of zcomp_strm structs in compression
backend's idle list (max_comp_streams).
max_comp_streams used during initialisation as follows:
-- passing to zcomp_create() max_strm equals to 1 will initialise zcomp
using single compression stream zcomp_strm_single (mutex-based locking).
-- passing to zcomp_create() max_strm greater than 1 will initialise zcomp
using multi compression stream zcomp_strm_multi (spinlock-based locking).
default max_comp_streams value is 1, meaning that zram with single stream
will be initialised.
Later patch will introduce configuration knob to change max_comp_streams
on already initialised and used zcomp.
TEST
iozone -t 3 -R -r 16K -s 60M -I +Z
test base 1 strm (mutex) 3 strm (spinlock)
-----------------------------------------------------------------------
Initial write 589286.78 583518.39 718011.05
Rewrite 604837.97 596776.38 1515125.72
Random write 584120.11 595714.58 1388850.25
Pwrite 535731.17 541117.38 739295.27
Fwrite 1418083.88 1478612.72 1484927.06
Usage example:
set max_comp_streams to 4
echo 4 > /sys/block/zram0/max_comp_streams
show current max_comp_streams (default value is 1).
cat /sys/block/zram0/max_comp_streams
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Document `failed_reads' and `failed_writes' device attributes.
Remove info about `discard' - there is no such zram attr.
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch-set includes the following major enhancement patches.
o introduce large directory support
o introduce f2fs_issue_flush to merge redundant flush commands
o merge write IOs as much as possible aligned to the segment
o add sysfs entries to tune the f2fs configuration
o use radix_tree for the free_nid_list to reduce in-memory operations
o remove costly bit operations in f2fs_find_entry
o enhance the readahead flow for CP/NAT/SIT/SSA blocks
The other bug fixes are as follows.
o recover xattr node blocks correctly after sudden-power-cut
o fix to calculate the maximum number of node ids
o enhance to handle many error cases
And, there are a bunch of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eSW+
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches.
- introduce large directory support
- introduce f2fs_issue_flush to merge redundant flush commands
- merge write IOs as much as possible aligned to the segment
- add sysfs entries to tune the f2fs configuration
- use radix_tree for the free_nid_list to reduce in-memory operations
- remove costly bit operations in f2fs_find_entry
- enhance the readahead flow for CP/NAT/SIT/SSA blocks
The other bug fixes are as follows:
- recover xattr node blocks correctly after sudden-power-cut
- fix to calculate the maximum number of node ids
- enhance to handle many error cases
And, there are a bunch of cleanups"
* tag 'for-f2fs-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (62 commits)
f2fs: fix wrong statistics of inline data
f2fs: check the acl's validity before setting
f2fs: introduce f2fs_issue_flush to avoid redundant flush issue
f2fs: fix to cover io->bio with io_rwsem
f2fs: fix error path when fail to read inline data
f2fs: use list_for_each_entry{_safe} for simplyfying code
f2fs: avoid free slab cache under spinlock
f2fs: avoid unneeded lookup when xattr name length is too long
f2fs: avoid unnecessary bio submit when wait page writeback
f2fs: return -EIO when node id is not matched
f2fs: avoid RECLAIM_FS-ON-W warning
f2fs: skip unnecessary node writes during fsync
f2fs: introduce fi->i_sem to protect fi's info
f2fs: change reclaim rate in percentage
f2fs: add missing documentation for dir_level
f2fs: remove unnecessary threshold
f2fs: throttle the memory footprint with a sysfs entry
f2fs: avoid to drop nat entries due to the negative nr_shrink
f2fs: call f2fs_wait_on_page_writeback instead of native function
f2fs: introduce nr_pages_to_write for segment alignment
...
According to the documentation, the various wakeup_* attributes in sysfs
are not present if the device is not enabled to wake up the system.
This is not correct: the attributes are not present if the device is not
capable to wake up the system. They are empty if the device is not enabled
to wake up the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
a staging driver; fix included. Greg KH said he'd take the patch
but hadn't as the merge window opened, so it's included here
to avoid breaking build.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=yzUO
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Nothing major: the stricter permissions checking for sysfs broke a
staging driver; fix included. Greg KH said he'd take the patch but
hadn't as the merge window opened, so it's included here to avoid
breaking build"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
staging: fix up speakup kobject mode
Use 'E' instead of 'X' for unsigned module taint flag.
VERIFY_OCTAL_PERMISSIONS: stricter checking for sysfs perms.
kallsyms: fix percpu vars on x86-64 with relocation.
kallsyms: generalize address range checking
module: LLVMLinux: Remove unused function warning from __param_check macro
Fix: module signature vs tracepoints: add new TAINT_UNSIGNED_MODULE
module: remove MODULE_GENERIC_TABLE
module: allow multiple calls to MODULE_DEVICE_TABLE() per module
module: use pr_cont
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Updates to devicetree core code. This branch contains the following notable changes:
* Add reserved memory binding
* Make struct device_node a kobject and remove legacy /proc/device-tree
* ePAPR conformance fixes
* Update in-kernel DTC copy to version v1.4.0
* Preparation changes for dynamic device tree overlays
* minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of the
old /proc/device-tree code. This simplifies the device tree handling
code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTOyNwAAoJEMWQL496c2LNZY0QAIreUrpo3/hKRau61EDPXkOA
UFRyPUHD0k/dNXWWDbTfvKH/nAfzdVwejhePqEWiODiFOFkq7JyQlMKPA+CZuZj0
ygN4215A1yj/hDf6JRD5Zn4WGpawDt9InlbZSps6P5dd8voV5t5dz6uzz+Y7uqaK
CAjTDlBSmxEen5vRHiHQgKv74au/+b9yfSURjPQVWg46+wl3WJwjsdzerphm4unW
tpEr8zkIsm51mqqAx4penIuiovh7+L2J5v4BFeg8o+kaZEuZpVxLHJPOuBd5hdom
zeqEIj3AqHTh5suYIHe4aAbZ2wMP3kYGgkPGwfWLnwLyULxalcCtGZeaCi9nwTFj
Fdj+7f17ocrt5mif0f5Deufi1LqJsDjhY6G9p7HuV7Y9hsMILpJIUoGENPji+TWj
BA4L45eaPmNYdKJytEtFD7F2WnXeHZ6fDtYho/39DWW+Bt16IFX85T199irhxGG4
byN6LRaahk2UeycSXkQHAlWOQHqzBcJJAkQLN2iahzyYRr9Dy+VI2E9clm53m49O
YQYcONdUlMYrtfRwJpbB9XHM0HgZUvg0LT5z/iHQs9uJtoo33Oj+zxFixyZLQ9Dq
qyLqQWEpV9gFLAo9tpf56gffkLiJRsHkX4UJ6oTtj4DY1WWU9H81jjCvv/7flzp/
8ZyyZzANQf1DZ9kqO2v+
=lyA5
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
Pull main powerpc updates from Ben Herrenschmidt:
"This time around, the powerpc merges are going to be a little bit more
complicated than usual.
This is the main pull request with most of the work for this merge
window. I will describe it a bit more further down.
There is some additional cpuidle driver work, however I haven't
included it in this tree as it depends on some work in tip/timer-core
which Thomas accidentally forgot to put in a topic branch. Since I
didn't want to carry all of that tip timer stuff in powerpc -next, I
setup a separate branch on top of Thomas tree with just that cpuidle
driver in it, and Stephen has been carrying that in next separately
for a while now. I'll send a separate pull request for it.
Additionally, two new pieces in this tree add users for a sysfs API
that Tejun and Greg have been deprecating in drivers-core-next.
Thankfully Greg reverted the patch that removes the old API so this
merge can happen cleanly, but once merged, I will send a patch
adjusting our new code to the new API so that Greg can send you the
removal patch.
Now as for the content of this branch, we have a lot of perf work for
power8 new counters including support for our new "nest" counters
(also called 24x7) under pHyp (not natively yet).
We have new functionality when running under the OPAL firmware
(non-virtualized or KVM host), such as access to the firmware error
logs and service processor dumps, system parameters and sensors, along
with a hwmon driver for the latter.
There's also a bunch of bug fixes accross the board, some LE fixes,
and a nice set of selftests for validating our various types of copy
loops.
On the Freescale side, we see mostly new chip/board revisions, some
clock updates, better support for machine checks and debug exceptions,
etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (70 commits)
powerpc/book3s: Fix CFAR clobbering issue in machine check handler.
powerpc/compat: 32-bit little endian machine name is ppcle, not ppc
powerpc/le: Big endian arguments for ppc_rtas()
powerpc: Use default set of netfilter modules (CONFIG_NETFILTER_ADVANCED=n)
powerpc/defconfigs: Enable THP in pseries defconfig
powerpc/mm: Make sure a local_irq_disable prevent a parallel THP split
powerpc: Rate-limit users spamming kernel log buffer
powerpc/perf: Fix handling of L3 events with bank == 1
powerpc/perf/hv_{gpci, 24x7}: Add documentation of device attributes
powerpc/perf: Add kconfig option for hypervisor provided counters
powerpc/perf: Add support for the hv 24x7 interface
powerpc/perf: Add support for the hv gpci (get performance counter info) interface
powerpc/perf: Add macros for defining event fields & formats
powerpc/perf: Add a shared interface to get gpci version and capabilities
powerpc/perf: Add 24x7 interface headers
powerpc/perf: Add hv_gpci interface header
powerpc: Add hvcalls for 24x7 and gpci (Get Performance Counter Info)
sysfs: create bin_attributes under the requested group
powerpc/perf: Enable BHRB access for EBB events
powerpc/perf: Add BHRB constraint and IFM MMCRA handling for EBB
...
This patch consists of the usual driver updates (megaraid_sas, scsi_debug,
qla2xxx, qla4xxx, lpfc, bnx2fc, be2iscsi, hpsa, ipr) plus an assortment of
minor fixes and the first precursors of SCSI-MQ (the code path
simplifications) and the bug fix for the USB oops on remove (which involves an
infrastructure change, so is sent via the main tree with a delayed backport
after a cycle in which it is shown to introduce no new bugs).
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTOsP1AAoJEDeqqVYsXL0MraUIAMCHWIN791cSc/E4d6mw/6nC
j5CG/wwuw3VfqJcJJ8PcItfReWPuS7aLwhAx3wNGDUe7Vcz9pmcgJU9c2/ZWhIJH
D0YXnGSkkfxI9Wc5WJ/NbueS0TFt0G5B6wpIxSLpSEJ1k9I90vxe3symCwv5vS/p
3Cd2nZZCLg6ArzZJ3PJLnNG9FUp2ZBeZwfPu4CuPm+3kEq9oRATg7bS4NNtVTQLP
0zNs5rKAVWfnE5Ii8VFjA7DLduG9W1IBNnSI7EERenrLKMbHG5530Rnl71uvjjgY
0jmQ5YGpTsYcJggLdaijZdK+zuq6Jtc+0DwWJKIE3cEHx3kUrYi4UQWTTRk9ttQ=
=Bp1Y
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch consists of the usual driver updates (megaraid_sas,
scsi_debug, qla2xxx, qla4xxx, lpfc, bnx2fc, be2iscsi, hpsa, ipr) plus
an assortment of minor fixes and the first precursors of SCSI-MQ (the
code path simplifications) and the bug fix for the USB oops on remove
(which involves an infrastructure change, so is sent via the main tree
with a delayed backport after a cycle in which it is shown to
introduce no new bugs)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (196 commits)
[SCSI] sd: Quiesce mode sense error messages
[SCSI] add support for per-host cmd pools
[SCSI] simplify command allocation and freeing a bit
[SCSI] megaraid: simplify internal command handling
[SCSI] ses: Use vpd information from scsi_device
[SCSI] Add EVPD page 0x83 and 0x80 to sysfs
[SCSI] Return VPD page length in scsi_vpd_inquiry()
[SCSI] scsi_sysfs: Implement 'is_visible' callback
[SCSI] hpsa: update driver version to 3.4.4-1
[SCSI] hpsa: fix bad endif placement in RAID 5 mapper code
[SCSI] qla2xxx: Fix build errors related to invalid print fields on some architectures.
[SCSI] bfa: Replace large udelay() with mdelay()
[SCSI] vmw_pvscsi: Some improvements in pvscsi driver.
[SCSI] vmw_pvscsi: Add support for I/O requests coalescing.
[SCSI] vmw_pvscsi: Fix pvscsi_abort() function.
[SCSI] remove deprecated IRQF_DISABLED from SCSI
[SCSI] bfa: Updating Maintainers email ids
[SCSI] ipr: Add new CCIN definition for Grand Canyon support
[SCSI] ipr: Format HCAM overlay ID 0x21
[SCSI] ipr: Use pci_enable_msi_range() and pci_enable_msix_range()
...
Add sysfs attributes Documentation entries for the basic set of
attributes that are exposed by a network device in
/sys/class/net/<iface>/
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Takashi Iwai <tiwai@suse.de> says:
> The letter 'X' has been already used for SUSE kernels for very long
> time, to indicate the external supported modules. Can the new flag be
> changed to another letter for avoiding conflict...?
> (BTW, we also use 'N' for "no support", too.)
Note: this code should be cleaned up, so we don't have such maps in
three places!
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
gpci and 24x7 expose some device specific attributes. Add some
documentation for them.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patchset adds some missing event list for POWER7 PMU raw
events which are exported through sysfs interface. Also updates
the ABI documentation to add all the sysfs exported raw events.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
With this patch a multicast packet is not always simply flooded anymore,
the behaviour for the following cases is changed to reduce
unnecessary overhead:
If all nodes within the horizon of a certain node have signalized
multicast listener announcement capability then an IPv6 multicast packet
with a destination of IPv6 link-local scope (excluding ff02::1) coming
from the upstream of this node...
* ...is dropped if there is no according multicast listener in the
translation table,
* ...is forwarded via unicast if there is a single node with interested
multicast listeners
* ...and otherwise still gets flooded.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
This patch adds the sysfs hooks needed in order to get and set the
programmable pin settings.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ram_thresh, a sysfs entry, which controls the memory
footprint used by the free nid list and the nat cache.
Previously, the free nid list was controlled by MAX_FREE_NIDS, while the nat
cache was managed by NM_WOUT_THRESHOLD.
However, this approach cannot be applied dynamically according to the system.
So, this patch adds ram_thresh that users can specify the threshold, which is
in order of 1 / 1024.
For example, if the total ram size is 4GB and the value is set to 10 by default,
f2fs tries to control the number of free nids and nat caches not to consume over
10 * (4GB / 1024) = 10MB.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add ABI documentation for in_*_mean_raw files, which are
already supported and used in the kernel for some time.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
AS3935 chipset can detect lightning strikes and reports those back as
events and the estimated distance to the storm.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Allow SSD Smart Path for a controller to be disabled by
the user, regardless of settings in controller firmware
or array configuration.
To disable: echo 0 > /sys/class/scsi_host/host<id>/acciopath_status
To re-enable: echo 1 > /sys/class/scsi_host/host<id>/acciopath_status
To check state: cat /sys/class/scsi_host/host<id>/acciopath_status
Signed-off-by: Scott Teel <scott.teel@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Users have reported being unable to trace non-signed modules loaded
within a kernel supporting module signature.
This is caused by tracepoint.c:tracepoint_module_coming() refusing to
take into account tracepoints sitting within force-loaded modules
(TAINT_FORCED_MODULE). The reason for this check, in the first place, is
that a force-loaded module may have a struct module incompatible with
the layout expected by the kernel, and can thus cause a kernel crash
upon forced load of that module on a kernel with CONFIG_TRACEPOINTS=y.
Tracepoints, however, specifically accept TAINT_OOT_MODULE and
TAINT_CRAP, since those modules do not lead to the "very likely system
crash" issue cited above for force-loaded modules.
With kernels having CONFIG_MODULE_SIG=y (signed modules), a non-signed
module is tainted re-using the TAINT_FORCED_MODULE taint flag.
Unfortunately, this means that Tracepoints treat that module as a
force-loaded module, and thus silently refuse to consider any tracepoint
within this module.
Since an unsigned module does not fit within the "very likely system
crash" category of tainting, add a new TAINT_UNSIGNED_MODULE taint flag
to specifically address this taint behavior, and accept those modules
within Tracepoints. We use the letter 'X' as a taint flag character for
a module being loaded that doesn't know how to sign its name (proposed
by Steven Rostedt).
Also add the missing 'O' entry to trace event show_module_flags() list
for the sake of completeness.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
NAKed-by: Ingo Molnar <mingo@redhat.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: David Howells <dhowells@redhat.com>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix descriptions of /sys/power/state in the documentation and in
a code comment.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Device tree nodes are already treated as objects, and we already want to
expose them to userspace which is done using the /proc filesystem today.
Right now the kernel has to do a lot of work to keep the /proc view in
sync with the in-kernel representation. If device_nodes are switched to
be kobjects then the device tree code can be a whole lot simpler. It
also turns out that switching to using /sysfs from /proc results in
smaller code and data size, and the userspace ABI won't change if
/proc/device-tree symlinks to /sys/firmware/devicetree/base.
v7: Add missing sysfs_bin_attr_init()
v6: Add __of_add_property() early init fixes from Pantelis
v5: Rename firmware/ofw to firmware/devicetree
Fix updating property values in sysfs
v4: Fixed build error on Powerpc
Fixed handling of dynamic nodes on powerpc
v3: Fixed handling of duplicate attribute and child node names
v2: switch to using sysfs bin_attributes which solve the problem of
reporting incorrect property size.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Add a wakeup_protocols sysfs file which controls the new
rc_dev::enabled_protocols[RC_FILTER_WAKEUP], which is the mask of
protocols that are used for the wakeup filter.
A new RC driver callback change_wakeup_protocol() is called to change
the wakeup protocol mask.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This enables support for userspace to fetch and initiate FSP and
Platform dumps from the service processor (via firmware) through sysfs.
Based on original patch from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Flow:
- We register for OPAL notification events.
- OPAL sends new dump available notification.
- We make information on dump available via sysfs
- Userspace requests dump contents
- We retrieve the dump via OPAL interface
- User copies the dump data
- userspace sends ack for dump
- We send ACK to OPAL.
sysfs files:
- We add the /sys/firmware/opal/dump directory
- echoing 1 (well, anything, but in future we may support
different dump types) to /sys/firmware/opal/dump/initiate_dump
will initiate a dump.
- Each dump that we've been notified of gets a directory
in /sys/firmware/opal/dump/ with a name of the dump type and ID (in hex,
as this is what's used elsewhere to identify the dump).
- Each dump has files: id, type, dump and acknowledge
dump is binary and is the dump itself.
echoing 'ack' to acknowledge (currently any string will do) will
acknowledge the dump and it will soon after disappear from sysfs.
OPAL APIs:
- opal_dump_init()
- opal_dump_info()
- opal_dump_read()
- opal_dump_ack()
- opal_dump_resend_notification()
Currently we are only ever notified for one dump at a time (until
the user explicitly acks the current dump, then we get a notification
of the next dump), but this kernel code should "just work" when OPAL
starts notifying us of all the dumps present.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Based on a patch by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
This patch adds support to read error logs from OPAL and export
them to userspace through a sysfs interface.
We export each log entry as a directory in /sys/firmware/opal/elog/
Currently, OPAL will buffer up to 128 error log records, we don't
need to have any knowledge of this limit on the Linux side as that
is actually largely transparent to us.
Each error log entry has the following files: id, type, acknowledge, raw.
Currently we just export the raw binary error log in the 'raw' attribute.
In a future patch, we may parse more of the error log to make it a bit
easier for userspace (e.g. to be able to display a brief summary in
petitboot without having to have a full parser).
If we have >128 logs from OPAL, we'll only be notified of 128 until
userspace starts acknowledging them. This limitation may be lifted in
the future and with this patch, that should "just work" from the linux side.
A userspace daemon should:
- wait for error log entries using normal mechanisms (we announce creation)
- read error log entry
- save error log entry safely to disk
- acknowledge the error log entry
- rinse, repeat.
On the Linux side, we read the error log when we're notified of it. This
possibly isn't ideal as it would be better to only read them on-demand.
However, this doesn't really work with current OPAL interface, so we
read the error log immediately when notified at the moment.
I've tested this pretty extensively and am rather confident that the
linux side of things works rather well. There is currently an issue with
the service processor side of things for >128 error logs though.
Signed-off-by: Stewart Smith <stewart@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d8a5dc3033.
This breaks plymouth installs, either because plymouth is using the file
"incorrectly" or because the patch is incorrect. Either way, this needs
to be reverted until it is all figured out.
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Ray Strode <halfline@gmail.com>
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Werner Fink <werner@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the PHY device has_fixups boolean as a sysfs property to help
troubleshooting PHY configurations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the PHY device interface mode through sysfs since this is an
useful piece of information for knowing how the attached networking
device will have configured its transmit/receive path.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new latency tolerance device PM QoS type to be use for
specifying active state (RPM_ACTIVE) memory access (DMA) latency
tolerance requirements for devices. It may be used to prevent
hardware from choosing overly aggressive energy-saving operation
modes (causing too much latency to appear) for the whole platform.
This feature reqiures hardware support, so it only will be
available for devices having a new .set_latency_tolerance()
callback in struct dev_pm_info populated, in which case the
routine pointed to by it should implement whatever is necessary
to transfer the effective requirement value to the hardware.
Whenever the effective latency tolerance changes for the device,
its .set_latency_tolerance() callback will be executed and the
effective value will be passed to it. If that value is negative,
which means that the list of latency tolerance requirements for
the device is empty, the callback is expected to switch the
underlying hardware latency tolerance control mechanism to an
autonomous mode if available. If that value is PM_QOS_LATENCY_ANY,
in turn, and the hardware supports a special "no requirement"
setting, the callback is expected to use it. That allows software
to prevent the hardware from automatically updating the device's
latency tolerance in response to its power state changes (e.g. during
transitions from D3cold to D0), which generally may be done in the
autonomous latency tolerance control mode.
If .set_latency_tolerance() is present for the device, a new
pm_qos_latency_tolerance_us attribute will be present in the
devivce's power directory in sysfs. Then, user space can use
that attribute to specify its latency tolerance requirement for
the device, if any. Writing "any" to it means "no requirement, but
do not let the hardware control latency tolerance" and writing
"auto" to it allows the hardware to be switched to the autonomous
mode if there are no other requirements from the kernel side in the
device's list.
This changeset includes a fix from Mika Westerberg.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The 'active' sysfs attribute should refer to the currently active tty
devices the console is running on, not the currently active console.
The console structure doesn't refer to any device in sysfs, only the tty
the console is running on has. So we need to print out the tty names in
'active', not the console names.
This resolves an issue on s390 platforms in determining the correct
console device to use.
Cc: Lennart Poettering <lennart@poettering.net>
Cc: Kay Sievers <kay@vrfy.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Werner Fink <werner@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add and document a generic sysfs based scancode filtering interface for
making use of IR data matching hardware to filter out uninteresting
scancodes. Two filters exist, one for normal operation and one for
filtering scancodes which are permitted to wake the system from suspend.
The following files are added to /sys/class/rc/rc?/:
- filter: normal scancode filter value
- filter_mask: normal scancode filter mask
- wakeup_filter: wakeup scancode filter value
- wakeup_filter_mask: wakeup scancode filter mask
A new s_filter() driver callback is added which must arrange for the
specified filter to be applied at the right time. Drivers can convert
the scancode filter into a raw IR data filter, which can be applied
immediately or later (for wake up filters).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: Rob Landley <rob@landley.net>
Cc: linux-doc@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Briefly document /sys/class/rc/ API for remote controller devices in
Documentation/ABI/teting.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull ceph updates from Sage Weil:
"This is a big batch. From Ilya we have:
- rbd support for more than ~250 mapped devices (now uses same scheme
that SCSI does for device major/minor numbering)
- crush updates for new mapping behaviors (will be needed for coming
erasure coding support, among other things)
- preliminary support for tiered storage pools
There is also a big series fixing a pile cephfs bugs with clustered
MDSs from Yan Zheng, ACL support for cephfs from Guangliang Zhao, ceph
fscache improvements from Li Wang, improved behavior when we get
ENOSPC from Josh Durgin, some readv/writev improvements from
Majianpeng, and the usual mix of small cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (76 commits)
ceph: cast PAGE_SIZE to size_t in ceph_sync_write()
ceph: fix dout() compile warnings in ceph_filemap_fault()
libceph: support CEPH_FEATURE_OSD_CACHEPOOL feature
libceph: follow redirect replies from osds
libceph: rename ceph_osd_request::r_{oloc,oid} to r_base_{oloc,oid}
libceph: follow {read,write}_tier fields on osd request submission
libceph: add ceph_pg_pool_by_id()
libceph: CEPH_OSD_FLAG_* enum update
libceph: replace ceph_calc_ceph_pg() with ceph_oloc_oid_to_pg()
libceph: introduce and start using oid abstraction
libceph: rename MAX_OBJ_NAME_SIZE to CEPH_MAX_OID_NAME_LEN
libceph: move ceph_file_layout helpers to ceph_fs.h
libceph: start using oloc abstraction
libceph: dout() is missing a newline
libceph: add ceph_kv{malloc,free}() and switch to them
libceph: support CEPH_FEATURE_EXPORT_PEER
ceph: add imported caps when handling cap export message
ceph: add open export target session helper
ceph: remove exported caps when handling cap import message
ceph: handle session flush message
...
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
/sys/kernel/vmcoreinfo was introduced long back but there is no ABI
documentation. This patch adds the documentation.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Ken'ichi Ohmichi <oomichi@mxs.nes.nec.co.jp>
Cc: Dan Aloni <da-x@monatomic.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch-set includes the following major enhancement patches.
o support inline_data
o refactor bio operations such as merge operations and rw type assignment
o enhance the direct IO path
o enhance bio operations
o truncate a node page when it becomes obsolete
o add sysfs entries: small_discards, max_victim_search, and in-place-update
o add a sysfs entry to control max_victim_search
The other bug fixes are as follows.
o fix a bug in truncate_partial_nodes
o avoid warnings during sparse and build process
o fix error handling flows
o fix potential bit overflows
And, there are a bunch of cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gVDh
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this round, a couple of sysfs entries were introduced to tune the
f2fs at runtime.
In addition, f2fs starts to support inline_data and improves the
read/write performance in some workloads by refactoring bio-related
flows.
This patch-set includes the following major enhancement patches.
- support inline_data
- refactor bio operations such as merge operations and rw type
assignment
- enhance the direct IO path
- enhance bio operations
- truncate a node page when it becomes obsolete
- add sysfs entries: small_discards, max_victim_search, and
in-place-update
- add a sysfs entry to control max_victim_search
The other bug fixes are as follows.
- fix a bug in truncate_partial_nodes
- avoid warnings during sparse and build process
- fix error handling flows
- fix potential bit overflows
And, there are a bunch of cleanups"
* tag 'for-f2fs-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (95 commits)
f2fs: drop obsolete node page when it is truncated
f2fs: introduce NODE_MAPPING for code consistency
f2fs: remove the orphan block page array
f2fs: add help function META_MAPPING
f2fs: move a branch for code redability
f2fs: call mark_inode_dirty to flush dirty pages
f2fs: clean checkpatch warnings
f2fs: missing REQ_META and REQ_PRIO when sync_meta_pages(META_FLUSH)
f2fs: avoid f2fs_balance_fs call during pageout
f2fs: add delimiter to seperate name and value in debug phrase
f2fs: use spinlock rather than mutex for better speed
f2fs: move alloc new orphan node out of lock protection region
f2fs: move grabing orphan pages out of protection region
f2fs: remove the needless parameter of f2fs_wait_on_page_writeback
f2fs: update documents and a MAINTAINERS entry
f2fs: add a sysfs entry to control max_victim_search
f2fs: improve write performance under frequent fsync calls
f2fs: avoid to read inline data except first page
f2fs: avoid to left uninitialized data in page when read inline data
f2fs: fix truncate_partial_nodes bug
...
Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of people.)
USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdjwIACgkQMUfUDdst+ylBIQCgkRoR8lJc0L5lZ3fugIJL4IzZ
j6AAn0nBLP6VI0cvUEi3TcrPTzv4MEuL
=Yb+I
-----END PGP SIGNATURE-----
Merge tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB pull request for 3.14-rc1
Lots of little things all over the place, and the usual USB gadget
updates, and XHCI fixes (some for an issue reported by a lot of
people). USB PHY updates as well as chipidea updates and fixes.
All of these have been in the linux-next tree with no reported issues"
* tag 'usb-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (318 commits)
usb: chipidea: udc: using MultO at TD as real mult value for ISO-TX
usb: chipidea: need to mask INT_STATUS when write otgsc
usb: chipidea: put hw_phymode_configure before ci_usb_phy_init
usb: chipidea: Fix Internal error: : 808 [#1] ARM related to STS flag
usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28
usb: chipidea: add freescale imx28 special write register method
usb: ehci: add freescale imx28 special write register method
usb: core: check for valid id_table when using the RefId feature
usb: cdc-wdm: resp_count can be 0 even if WDM_READ is set
usb: core: bail out if user gives an unknown RefId when using new_id
usb: core: allow a reference device for new_id
usb: core: add sanity checks when using bInterfaceClass with new_id
USB: image: correct spelling mistake in comment
USB: c67x00: correct spelling mistakes in comments
usb: delete non-required instances of include <linux/init.h>
usb:hub set hub->change_bits when over-current happens
Revert "usb: chipidea: imx: set CI_HDRC_IMX28_WRITE_FIX for imx28"
xhci: Set scatter-gather limit to avoid failed block writes.
xhci: Avoid infinite loop when sg urb requires too many trbs
usb: gadget: remove unused variable in gr_queue_int()
...
Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here due
to the subsystem still crossing staging and drivers/iio/, and the dwc2
driver is moved out of staging. There's a new driver (rts5208), which
ends up making us adding more lines than removing, but overall there was
lots of work toward moving code out of here, which was good.
All of this has been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdiE8ACgkQMUfUDdst+ynmYgCcDI9d1Jjo42+tpilIl3hOEb/f
sF8An1W3HRXM3XPG+X1POqprMAk0Jt63
=1Ztu
-----END PGP SIGNATURE-----
Merge tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver tree changes from Greg KH:
"Here's the big drivers/staging/ update for 3.14-rc1
Lots and lots of cleanups, IIO driver updates are also mixed in here
due to the subsystem still crossing staging and drivers/iio/, and the
dwc2 driver is moved out of staging. There's a new driver (rts5208),
which ends up making us adding more lines than removing, but overall
there was lots of work toward moving code out of here, which was good
All of this has been in linux-next with no reported issues"
* tag 'staging-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1084 commits)
lustre: delete linux/lustre_debug.h
staging: lustre: remove some unused debug macros
usb: dwc2: move device tree bindings doc to correct place
staging: vt6656: sparse fixes: iwctl_giwgenie use memcpy.
staging: vt6656: sparse fixes: iwctl_siwgenie use memcpy.
staging: vt6656: sparse fixes ethtool_ioctl Use struct ifreq *
staging: vt6656: sparse fixes: dpc.c missing dpc.h
staging: lustre: libcfs_debug: small whitespace cleanups
staging: lustre: libcfs_debug.h: remove extra blank lines
staging: lustre: libcfs_debug.h: Align backslashes in macros
staging: lustre: libcfs_debug.h: align define values
staging: tidspbridge: adjust error return code (bugfix)
Staging: rts5139: rts51x_card: fixed style issues
staging: wlags49_h2: Fix "do not use C99 //" in wl_cs.h, wl_enc.h wl_main.h and wl_wext.h
Staging: rtl8188eu: Fixed "foo * bar" related coding style issues
Staging: rtl8188eu: Fixed required spaces after ',' and around '=' and '=='
staging: vt6655: Fix memory leak in wpa_ioctl()
imx-drm: parallel-display: honor 'native-mode' property when selecting video mode from DT
staging: drm/imx: don't drop crtc offsets when doing pageflip
staging: drm/imx: handle framebuffer offsets correctly
...
Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details are
in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlLdgc8ACgkQMUfUDdst+ynt9ACguAhrO2WlowdcUZELadTEpqLX
gbkAn0+c1rjizVdIRvs83aQRNJP6w1uR
=oPmD
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg KH:
"Here's the big char/misc driver patches for 3.14-rc1.
Lots of little things, and a new "big" driver, genwqe. Full details
are in the shortlog"
* tag 'char-misc-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
mei: limit the number of consecutive resets
mei: revamp mei reset state machine
drivers/char: don't use module_init in non-modular ttyprintk.c
VMCI: fix error handling path when registering guest driver
extcon: gpio: Add power resume support
Documentation: HOWTO: Updates on subsystem trees, patchwork, -next (vs. -mm) in ko_KR
Documentation: HOWTO: update for 2.6.x -> 3.x versioning in ko_KR
Documentation: HOWTO: update stable address in ko_KR
Documentation: HOWTO: update LXR web link in ko_KR
char: nwbutton: open-code interruptible_sleep_on
mei: fix syntax in comments and debug output
mei: nfc: mei_nfc_free has to be called under lock
mei: use hbm idle state to prevent spurious resets
mei: do not run reset flow from the interrupt thread
misc: genwqe: fix return value check in genwqe_device_create()
GenWQE: Fix warnings for sparc
GenWQE: Fix compile problems for Alpha
Documentation/misc-devices/mei/mei-amt-version.c: remove unneeded call of mei_deinit()
GenWQE: Rework return code for flash-update ioctl
sgi-xp: open-code interruptible_sleep_on_timeout
...
Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds missing some description of sysfs entries in
- Documentation/ABI/testing/sysfs-fs-f2fs
- Documentation/filesystems/f2fs.txt.
And it adds a maintained document entry of F2FS in MAINTAINERS.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Add a Documentation/ABI entry for
/sys/devices/system/cpu/intel_pstate/max_perf_pct,
/sys/devices/system/cpu/intel_pstate/min_perf_pct, and
/sys/devices/system/cpu/intel_pstate/no_turbo.
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently each rbd device is allocated its own major number, which
leads to a hard limit of 230-250 images mapped at once. This commit
adds support for a new single-major device number allocation scheme,
which is hidden behind a new single_major boolean module parameter and
is disabled by default for backwards compatibility reasons. (Old
userspace cannot correctly unmap images mapped under single-major
scheme and would essentially just unmap a random image, if that.)
$ rbd showmapped
id pool image snap device
0 rbd b100 - /dev/rbd0
1 rbd b101 - /dev/rbd1
2 rbd b102 - /dev/rbd2
3 rbd b103 - /dev/rbd3
Old scheme (modprobe rbd):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:24 /dev/rbd0
brw-rw---- 1 root disk 252, 0 Dec 10 12:28 /dev/rbd1
brw-rw---- 1 root disk 252, 1 Dec 10 12:28 /dev/rbd1p1
brw-rw---- 1 root disk 252, 2 Dec 10 12:28 /dev/rbd1p2
brw-rw---- 1 root disk 252, 3 Dec 10 12:28 /dev/rbd1p3
brw-rw---- 1 root disk 251, 0 Dec 10 12:28 /dev/rbd2
brw-rw---- 1 root disk 251, 1 Dec 10 12:28 /dev/rbd2p1
brw-rw---- 1 root disk 250, 0 Dec 10 12:24 /dev/rbd3
New scheme (modprobe rbd single_major=Y):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:30 /dev/rbd0
brw-rw---- 1 root disk 253, 256 Dec 10 12:30 /dev/rbd1
brw-rw---- 1 root disk 253, 257 Dec 10 12:30 /dev/rbd1p1
brw-rw---- 1 root disk 253, 258 Dec 10 12:30 /dev/rbd1p2
brw-rw---- 1 root disk 253, 259 Dec 10 12:30 /dev/rbd1p3
brw-rw---- 1 root disk 253, 512 Dec 10 12:30 /dev/rbd2
brw-rw---- 1 root disk 253, 513 Dec 10 12:30 /dev/rbd2p1
brw-rw---- 1 root disk 253, 768 Dec 10 12:30 /dev/rbd3
(major 253 was assigned dynamically at module load time)
The new limit is 4096 images mapped at once, and it comes from the fact
that, as before, 256 minor numbers are reserved for each mapping.
(A follow-up commit changes the number of minors reserved and the way
we deal with partitions over that number.)
If single_major is set to true, two new sysfs interfaces show up:
/sys/bus/rbd/{add,remove}_single_major. These are to be used instead
of /sys/bus/rbd/{add,remove}, which are disabled for backwards
compatibility reasons outlined above.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Introduce /sys/bus/rbd/devices/<id>/minor sysfs attribute for exporting
rbd whole disk minor numbers. This is a step towards single-major
device number allocation scheme, but also a good thing on its own.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
kexec-tools use boot_params for getting the 1st kernel hardware_subarch,
the kexec kernel EFI runtime support also needs to read the old efi_info
from boot_params. Currently it exists in debugfs which is not a good
place for such infomation. Per HPA, we should avoid "sploit debugfs".
In this patch /sys/kernel/boot_params are exported, also the setup_data is
exported as a subdirectory. kexec-tools is using debugfs for hardware_subarch
for a long time now so we're not removing it yet.
Structure is like below:
/sys/kernel/boot_params
|__ data /* boot_params in binary*/
|__ setup_data
| |__ 0 /* the first setup_data node */
| | |__ data /* setup_data node 0 in binary*/
| | |__ type /* setup_data type of setup_data node 0, hex string */
[snip]
|__ version /* boot protocal version (in hex, "0x" prefixed)*/
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
kexec kernel will need exactly same mapping for EFI runtime memory
ranges. Thus here export the runtime ranges mapping to sysfs,
kexec-tools will assemble them and pass to 2nd kernel via setup_data.
Introducing a new directory /sys/firmware/efi/runtime-map just like
/sys/firmware/memmap. Containing below attribute in each file of that
directory:
attribute num_pages phys_addr type virt_addr
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Export fw_vendor, runtime and config table physical addresses to
/sys/firmware/efi/{fw_vendor,runtime,config_table} because kexec kernels
need them.
From EFI spec these 3 variables will be updated to virtual address after
entering virtual mode. But kernel startup code will need the physical
address.
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The PCI MSI sysfs code is a mess with kobjects for things that don't really
need to be kobjects. This patch creates attributes dynamically for the MSI
interrupts instead of using kobjects.
Note, this removes a directory from sysfs. Old MSI kobjects:
pci_device
└── msi_irqs
└── 40
└── mode
New MSI attributes:
pci_device
└── msi_irqs
└── 40
As there was only one file "mode" with the kobject model, the interrupt
number is now a file that returns the "mode" of the interrupt (msi vs.
msix).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Sysfs interfaces for the GenWQE card. There are attributes to query
the version of the bitstream as well as some for the driver. For
debugging, please also see the debugfs interfaces of this driver.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Co-authors: Joerg-Stephan Vogt <jsvogt@de.ibm.com>,
Michael Jung <MIJUNG@de.ibm.com>,
Michael Ruettger <michael@ibmra.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Debugfs interfaces for the GenWQE card. Help to debug potential
problems. Dump internal chip state for debugging and failure
determination.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Co-authors: Joerg-Stephan Vogt <jsvogt@de.ibm.com>,
Michael Jung <MIJUNG@de.ibm.com>,
Michael Ruettger <michael@ibmra.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for using FunctionFS in configfs-based USB gadgets.
[ balbi@ti.com : removed redefinition of VERBOSE_DEBUG and few
trailing whitespaces ]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add Tahvo USB transceiver driver.
Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are already humidity sensors in the hwmon subsystem,
so we use their unit (milli percent) here as well.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for using the sourcesink function in gadgets composed with
configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using the loopback USB function in gadgets composed with
configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
Pull HID updates from Jiri Kosina:
- i2c-hid is not querying init reports any more, as it's not mandated
by the spec, and annoys quite a few devices during enumeration, by
Bibek Basu
- a lot of fixes for Logitech devices, by Simon Wood
- hid-apple now has an option to switch between Option and Command
mode, by Nanno Langstraat
- Some more workarounds for severely broken ELO devices, by Oliver
Neukum
- more devm conversions, by Benjamin Tissoires
- wiimote correctness fixes, by David Herrmann
- a lot of added support for various new device IDs and random small
fixes here and there"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (34 commits)
HID: enable Mayflash USB Gamecube Adapter
HID: sony: Add force feedback support for Dualshock3 USB
Input: usbtouchscreen: ignore eGalax/D-Wav/EETI HIDs
HID: don't ignore eGalax/D-Wav/EETI HIDs
HID: roccat: add missing special driver declarations
HID:hid-lg4ff: Correct Auto-center strength for wheels other than MOMO and MOMO2
HID:hid-lg4ff: Initialize device properties before we touch autocentering.
HID:hid-lg4ff: ensure ConstantForce is disabled when set to 0
HID:hid-lg4ff: Switch autocentering off when strength is set to zero.
HID:hid-lg4ff: Scale autocentering force properly on Logitech wheel
HID: roccat: fix Coverity CID 141438
HID: multitouch: add manufacturer to Kconfig help text
HID: logitech-dj: small cleanup in rdcat()
HID: remove self-assignment from hid_input_report
HID: hid-sensor-hub: fix report size
HID: i2c-hid: Stop querying for init reports
HID: roccat: add support for Ryos MK keyboards
HID: roccat: generalize some common code
HID: roccat: add new device return value
HID: wiimote: add pro-controller analog stick calibration
...
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from
Mika Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh Kumar,
Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz Majewski,
Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki,
Naresh Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani,
Zhang Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko,
Al Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JCxk
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael J Wysocki:
- New power capping framework and the the Intel Running Average Power
Limit (RAPL) driver using it from Srinivas Pandruvada and Jacob Pan.
- Addition of the in-kernel switching feature to the arm_big_little
cpufreq driver from Viresh Kumar and Nicolas Pitre.
- cpufreq support for iMac G5 from Aaro Koskinen.
- Baytrail processors support for intel_pstate from Dirk Brandewie.
- cpufreq support for Midway/ECX-2000 from Mark Langsdorf.
- ARM vexpress/TC2 cpufreq support from Sudeep KarkadaNagesha.
- ACPI power management support for the I2C and SPI bus types from Mika
Westerberg and Lv Zheng.
- cpufreq core fixes and cleanups from Viresh Kumar, Srivatsa S Bhat,
Stratos Karafotis, Xiaoguang Chen, Lan Tianyu.
- cpufreq drivers updates (mostly fixes and cleanups) from Viresh
Kumar, Aaro Koskinen, Jungseok Lee, Sudeep KarkadaNagesha, Lukasz
Majewski, Manish Badarkhe, Hans-Christian Egtvedt, Evgeny Kapaev.
- intel_pstate updates from Dirk Brandewie and Adrian Huang.
- ACPICA update to version 20130927 includig fixes and cleanups and
some reduction of divergences between the ACPICA code in the kernel
and ACPICA upstream in order to improve the automatic ACPICA patch
generation process. From Bob Moore, Lv Zheng, Tomasz Nowicki, Naresh
Bhat, Bjorn Helgaas, David E Box.
- ACPI IPMI driver fixes and cleanups from Lv Zheng.
- ACPI hotplug fixes and cleanups from Bjorn Helgaas, Toshi Kani, Zhang
Yanfei, Rafael J Wysocki.
- Conversion of the ACPI AC driver to the platform bus type and
multiple driver fixes and cleanups related to ACPI from Zhang Rui.
- ACPI processor driver fixes and cleanups from Hanjun Guo, Jiang Liu,
Bartlomiej Zolnierkiewicz, Mathieu Rhéaume, Rafael J Wysocki.
- Fixes and cleanups and new blacklist entries related to the ACPI
video support from Aaron Lu, Felipe Contreras, Lennart Poettering,
Kirill Tkhai.
- cpuidle core cleanups from Viresh Kumar and Lorenzo Pieralisi.
- cpuidle drivers fixes and cleanups from Daniel Lezcano, Jingoo Han,
Bartlomiej Zolnierkiewicz, Prarit Bhargava.
- devfreq updates from Sachin Kamat, Dan Carpenter, Manish Badarkhe.
- Operation Performance Points (OPP) core updates from Nishanth Menon.
- Runtime power management core fix from Rafael J Wysocki and update
from Ulf Hansson.
- Hibernation fixes from Aaron Lu and Rafael J Wysocki.
- Device suspend/resume lockup detection mechanism from Benoit Goby.
- Removal of unused proc directories created for various ACPI drivers
from Lan Tianyu.
- ACPI LPSS driver fix and new device IDs for the ACPI platform scan
handler from Heikki Krogerus and Jarkko Nikula.
- New ACPI _OSI blacklist entry for Toshiba NB100 from Levente Kurusa.
- Assorted fixes and cleanups related to ACPI from Andy Shevchenko, Al
Stone, Bartlomiej Zolnierkiewicz, Colin Ian King, Dan Carpenter,
Felipe Contreras, Jianguo Wu, Lan Tianyu, Yinghai Lu, Mathias Krause,
Liu Chuansheng.
- Assorted PM fixes and cleanups from Andy Shevchenko, Thierry Reding,
Jean-Christophe Plagniol-Villard.
* tag 'pm+acpi-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (386 commits)
cpufreq: conservative: fix requested_freq reduction issue
ACPI / hotplug: Consolidate deferred execution of ACPI hotplug routines
PM / runtime: Use pm_runtime_put_sync() in __device_release_driver()
ACPI / event: remove unneeded NULL pointer check
Revert "ACPI / video: Ignore BIOS initial backlight value for HP 250 G1"
ACPI / video: Quirk initial backlight level 0
ACPI / video: Fix initial level validity test
intel_pstate: skip the driver if ACPI has power mgmt option
PM / hibernate: Avoid overflow in hibernate_preallocate_memory()
ACPI / hotplug: Do not execute "insert in progress" _OST
ACPI / hotplug: Carry out PCI root eject directly
ACPI / hotplug: Merge device hot-removal routines
ACPI / hotplug: Make acpi_bus_hot_remove_device() internal
ACPI / hotplug: Simplify device ejection routines
ACPI / hotplug: Fix handle_root_bridge_removal()
ACPI / hotplug: Refuse to hot-remove all objects with disabled hotplug
ACPI / scan: Start matching drivers after trying scan handlers
ACPI: Remove acpi_pci_slot_init() headers from internal.h
ACPI / blacklist: fix name of ThinkPad Edge E530
PowerCap: Fix build error with option -Werror=format-security
...
Conflicts:
arch/arm/mach-omap2/opp.c
drivers/Kconfig
drivers/spi/spi.c
* Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
* Other general cleanups (removing unused functions, options, variables,
fields; use correct interfaces)
* Fix BUG() for new odd-sized NAND, which report non-power-of-2 dimensions via
ONFI
* Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
* Improve differentiation between SLC and MLC NAND -- this clarifies an ABI
issue regarding the MTD "type" (in sysfs and in ioctl(MEMGETINFO)), where
the MTD_MLCNANDFLASH type was present but inconsistently used
* Extend GPMI NAND to support multi-chip-select NAND for some platforms
* Many improvements to the OMAP2/3 NAND driver, including an expanded DT
binding to bring us closer to mainline support for some OMAP systems
* Fix a deadlock in the error path of the Atmel NAND driver probe
* Correct the error codes from MTD mmap() to conform to POSIX and the Linux
Programmer's Manual. This is an acknowledged change in the MTD ABI, but I
can't imagine somebody relying on the non-standard -ENOSYS error code
specifically. Am I just being unimaginative? :)
* Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
* More? Read the log!
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=z5qO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd
Pull MTD changes from Brian Norris:
- Unify some compile-time differences so that we have fewer uses of
#ifdef CONFIG_OF in atmel_nand
- Other general cleanups (removing unused functions, options,
variables, fields; use correct interfaces)
- Fix BUG() for new odd-sized NAND, which report non-power-of-2
dimensions via ONFI
- Miscellaneous driver fixes (SPI NOR flash; BCM47xx NAND flash; etc.)
- Improve differentiation between SLC and MLC NAND -- this clarifies an
ABI issue regarding the MTD "type" (in sysfs and in the MEMGETINFO
ioctl), where the MTD_MLCNANDFLASH type was present but
inconsistently used
- Extend GPMI NAND to support multi-chip-select NAND for some platforms
- Many improvements to the OMAP2/3 NAND driver, including an expanded
DT binding to bring us closer to mainline support for some OMAP
systems
- Fix a deadlock in the error path of the Atmel NAND driver probe
- Correct the error codes from MTD mmap() to conform to POSIX and the
Linux Programmer's Manual. This is an acknowledged change in the MTD
ABI, but I can't imagine somebody relying on the non-standard -ENOSYS
error code specifically. Am I just being unimaginative? :)
- Fix a few important GPMI NAND bugs (one regression from 3.12 and one
long-standing race condition)
- More? Read the log!
* tag 'for-linus-20131112' of git://git.infradead.org/linux-mtd: (98 commits)
mtd: gpmi: fix the NULL pointer
mtd: gpmi: fix kernel BUG due to racing DMA operations
mtd: mtdchar: return expected errors on mmap() call
mtd: gpmi: only scan two chips for imx6
mtd: gpmi: Use devm_kzalloc()
mtd: atmel_nand: fix bug driver will in a dead lock if no nand detected
mtd: nand: use a local variable to simplify the nand_scan_tail
mtd: nand: remove deprecated IRQF_DISABLED
mtd: dataflash: Say if we find a device we don't support
mtd: nand: omap: fix error return code in omap_nand_probe()
mtd: nand_bbt: kill NAND_BBT_SCANALLPAGES
mtd: m25p80: fixup device removal failure path
mtd: mxc_nand: Include linux/of.h header
mtd: remove duplicated include from mtdcore.c
mtd: m25p80: add support for Macronix mx25l3255e
mtd: nand: omap: remove selection of BCH ecc-scheme via KConfig
mtd: nand: omap: updated devm_xx for all resource allocation and free calls
mtd: nand: omap: use drivers/mtd/nand/nand_bch.c wrapper for BCH ECC instead of lib/bch.c
mtd: nand: omap: clean-up ecc layout for BCH ecc schemes
mtd: nand: omap2: clean-up BCHx_HW and BCHx_SW ECC configurations in device_probe
...
Pull networking updates from David Miller:
1) The addition of nftables. No longer will we need protocol aware
firewall filtering modules, it can all live in userspace.
At the core of nftables is a, for lack of a better term, virtual
machine that executes byte codes to inspect packet or metadata
(arriving interface index, etc.) and make verdict decisions.
Besides support for loading packet contents and comparing them, the
interpreter supports lookups in various datastructures as
fundamental operations. For example sets are supports, and
therefore one could create a set of whitelist IP address entries
which have ACCEPT verdicts attached to them, and use the appropriate
byte codes to do such lookups.
Since the interpreted code is composed in userspace, userspace can
do things like optimize things before giving it to the kernel.
Another major improvement is the capability of atomically updating
portions of the ruleset. In the existing netfilter implementation,
one has to update the entire rule set in order to make a change and
this is very expensive.
Userspace tools exist to create nftables rules using existing
netfilter rule sets, but both kernel implementations will need to
co-exist for quite some time as we transition from the old to the
new stuff.
Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
worked so hard on this.
2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
to our pseudo-random number generator, mostly used for things like
UDP port randomization and netfitler, amongst other things.
In particular the taus88 generater is updated to taus113, and test
cases are added.
3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
and Yang Yingliang.
4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
Sujir.
5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
Neal Cardwell, and Yuchung Cheng.
6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
control message data, much like other socket option attributes.
From Francesco Fusco.
7) Allow applications to specify a cap on the rate computed
automatically by the kernel for pacing flows, via a new
SO_MAX_PACING_RATE socket option. From Eric Dumazet.
8) Make the initial autotuned send buffer sizing in TCP more closely
reflect actual needs, from Eric Dumazet.
9) Currently early socket demux only happens for TCP sockets, but we
can do it for connected UDP sockets too. Implementation from Shawn
Bohrer.
10) Refactor inet socket demux with the goal of improving hash demux
performance for listening sockets. With the main goals being able
to use RCU lookups on even request sockets, and eliminating the
listening lock contention. From Eric Dumazet.
11) The bonding layer has many demuxes in it's fast path, and an RCU
conversion was started back in 3.11, several changes here extend the
RCU usage to even more locations. From Ding Tianhong and Wang
Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
Falico.
12) Allow stackability of segmentation offloads to, in particular, allow
segmentation offloading over tunnels. From Eric Dumazet.
13) Significantly improve the handling of secret keys we input into the
various hash functions in the inet hashtables, TCP fast open, as
well as syncookies. From Hannes Frederic Sowa. The key fundamental
operation is "net_get_random_once()" which uses static keys.
Hannes even extended this to ipv4/ipv6 fragmentation handling and
our generic flow dissector.
14) The generic driver layer takes care now to set the driver data to
NULL on device removal, so it's no longer necessary for drivers to
explicitly set it to NULL any more. Many drivers have been cleaned
up in this way, from Jingoo Han.
15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.
16) Improve CRC32 interfaces and generic SKB checksum iterators so that
SCTP's checksumming can more cleanly be handled. Also from Daniel
Borkmann.
17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
using the interface MTU value. This helps avoid PMTU attacks,
particularly on DNS servers. From Hannes Frederic Sowa.
18) Use generic XPS for transmit queue steering rather than internal
(re-)implementation in virtio-net. From Jason Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
random32: add test cases for taus113 implementation
random32: upgrade taus88 generator to taus113 from errata paper
random32: move rnd_state to linux/random.h
random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
random32: add periodic reseeding
random32: fix off-by-one in seeding requirement
PHY: Add RTL8201CP phy_driver to realtek
xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
macmace: add missing platform_set_drvdata() in mace_probe()
ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
ixgbe: add warning when max_vfs is out of range.
igb: Update link modes display in ethtool
netfilter: push reasm skb through instead of original frag skbs
ip6_output: fragment outgoing reassembled skb properly
MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
net_sched: tbf: support of 64bit rates
ixgbe: deleting dfwd stations out of order can cause null ptr deref
ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
...
Discussion at Kernel Summit made it clear that the presence or absence of
specific Kconfig symbols are not considered ABI, and that no userspace (or
bootloader, etc) should rely on them.
In addition, kernel-internal symbols are well established as non-ABI, per
Documentation/stable_api_nonsense.txt.
Document both of these in Documentation/ABI/README, in a new section for
notable bits of non-ABI.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: Rob Landley <rob@landley.net>
Cc: Tao Ma <boyu.mt@taobao.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Certain storage configurations, e.g. a sufficiently large array of
hard disks in a RAID configuration, need a queue depth above 64 to
achieve optimal performance. Hence make the queue depth configurable.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Tested-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
On an initiator system with multiple IB ports it is not yet possible
to figure out what the originating port of an SRP connection is. Hence
make the source GID available in sysfs.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add support for periodically reconnecting to an SRP target until
the dev_loss timer expires. After the tenth reconnection attempt,
gradually slow down subsequent reconnect attempts.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add the necessary functions in the SRP transport module to allow an
SRP initiator driver to implement transport layer error handling
similar to the functionality already provided by the FC transport
layer. This includes:
- Support for implementing fast_io_fail_tmo, the time that should
elapse after having detected a transport layer problem and
before failing I/O.
- Support for implementing dev_loss_tmo, the time that should
elapse after having detected a transport layer problem and
before removing a remote port.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Allow the InfiniBand RC retry count to be configured by the user as an
option in the target login string. Reducing this retry count allows to
reduce the path failover time.
Signed-off-by: Vu Pham <vu@mellanox.com>
[ bvanassche: Rewrote patch description / changed default retry count ]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Here's the big drivers/staging/ update for 3.13-rc1.
Nothing major here, just a _ton_ of fixes and cleanups, mostly driven by
the new round of OPW applicants, but also there are lots of other people
doing staging tree cleanups these days in order to help get the drivers
into mergable shape.
We also merge, and then revert, the ktap code, as Ingo and the other
perf/ftrace developers feel it should go into the "real" part of the
kernel with only a bit more work, so no need to put it in staging for
now.
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlJ6xPsACgkQMUfUDdst+ykAbwCg1hOktgHPFZp/t6xmsSj6cZHj
AfQAnRN/lr/TFw5SKUek2sluAzO4Fz7c
=g/MD
-----END PGP SIGNATURE-----
Merge tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver update from Greg KH:
"Here's the big drivers/staging/ update for 3.13-rc1.
Nothing major here, just a _ton_ of fixes and cleanups, mostly driven
by the new round of OPW applicants, but also there are lots of other
people doing staging tree cleanups these days in order to help get the
drivers into mergable shape.
We also merge, and then revert, the ktap code, as Ingo and the other
perf/ftrace developers feel it should go into the "real" part of the
kernel with only a bit more work, so no need to put it in staging for
now.
All of this has been in linux-next for a while with no reported
issues"
* tag 'staging-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1045 commits)
staging: drm/imx: fix return value check in ipu_add_subdevice_pdata()
Staging: zram: Fix access of NULL pointer
Staging: zram: Fix variable dereferenced before check
Staging: rtl8187se: space prohibited before semicolon in r8185b_init.c
Staging: rtl8187se: fix space prohibited after that open parenthesis '(' in r8185b_init.c
Staging: rtl8187se: fix braces {} are not necessary for single statement blocks in r8185b_init.c
Staging: rtl8187se: fix trailing whitespace in r8185b_init.c
Staging: rtl8187se: fix please, no space before tabs in r8185b_init.c
drivers/staging/nvec/Kconfig: remove trailing whitespace
Staging: dwc2: Fix variable dereferenced before check
Staging: xgifb: fix braces {} are not necessary for any arm of this statement
staging: rtl8192e: remove unneeded semicolons
staging: rtl8192e: use true and false for bool variables
staging: ft1000: return values corrected in scram_start_dwnld
staging: ft1000: change values of status return variable in write_dpram32_and_check
staging: bcm: Remove unnecessary pointer casting
imx-drm: ipuv3-crtc: Invert IPU DI0 clock polarity
staging: r8188eu: Fix sparse warnings in rtl_p2p.c
staging: r8188eu: Fix sparse warnings in rtw_mlme_ext.c
staging: r8188eu: Fix sparse warnings in rtl8188e.cmd.c
...
Here's the big char/misc driver patchset for 3.13-rc1.
Lots of stuff in here, including some new drivers for Intel's "MIC"
co-processor devices, and a new eeprom driver. Other things include the
driver attribute cleanups, extcon driver updates, hyperv updates, and a
raft of other miscellaneous driver fixes.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEUEABECAAYFAlJ6v9kACgkQMUfUDdst+ykPzACXdwm/1DryfqnyhVPyITNAKcma
WACg1Yu5mtIvJg3NsN/7Ff0Qfj6GzYY=
=MIEe
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here's the big char/misc driver patchset for 3.13-rc1.
Lots of stuff in here, including some new drivers for Intel's "MIC"
co-processor devices, and a new eeprom driver. Other things include
the driver attribute cleanups, extcon driver updates, hyperv updates,
and a raft of other miscellaneous driver fixes.
All of these have been in linux-next for a while"
* tag 'char-misc-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (121 commits)
misc: mic: Fixes for randconfig build errors and warnings.
tifm: fix error return code in tifm_7xx1_probe()
w1-gpio: Use devm_* functions
w1-gpio: Detect of_gpio_error for first gpio
uio: Pass pointers to virt_to_page(), not integers
uio: fix memory leak
misc/at24: avoid infinite loop on write()
misc/93xx46: avoid infinite loop on write()
misc: atmel_pwm: add deferred-probing support
mei: wd: host_init propagate error codes from called functions
mei: replace stray pr_debug with dev_dbg
mei: bus: propagate error code returned by mei_me_cl_by_id
mei: mei_cl_link remove duplicated check for open_handle_count
mei: print correct device state during unexpected reset
mei: nfc: fix memory leak in error path
lkdtm: add tests for additional page permissions
lkdtm: adjust recursion size to avoid warnings
lkdtm: isolate stack corruption test
mei: move host_clients_map cleanup to device init
mei: me: downgrade two errors to debug level
...
Added support for 3 keyboards with increasing illumination capabilities
Signed-off-by: Stefan Achatz <erazor_de@users.sourceforge.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The analog sticks of the pro-controller might report slightly off values.
To guarantee a uniform setup, we now calibrate analog-stick values during
pro-controller setup.
Unfortunately, the pro-controller fails during normal EEPROM reads and I
couldn't figure out whether there are any calibration values stored on the
device. Therefore, we now use the first values reported by the device (iff
they are not _way_ off, which would indicate movement) to initialize the
calibration values. To allow users to change this calibration data, we
provide a pro_calib sysfs attribute.
We also change the "flat" values so user-space correctly smoothes our
data. It makes slightly off zero-positions less visible while still
guaranteeing highly precise movement reports. Note that the pro controller
reports zero-positions in a quite huge range (at least: -100 to +100).
Reported-by: Rafael Brune <mail@rbrune.de>
Tested-by: Rafael Brune <mail@rbrune.de>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* powercap:
PowerCap: Convert class code to use dev_groups
PowerCap: Introduce Intel RAPL power capping driver
bitops: Introduce BIT_ULL
x86 / msr: add 64bit _on_cpu access functions
PowerCap: Add to drivers Kconfig and Makefile
PowerCap: Add class driver
PowerCap: Documentation
The current mtd_type_show() misses the MTD_MLCNANDFLASH case.
This patch adds the case for it, and also updates the ABI.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
include/net/dst.h
Trivial merge conflicts, both were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
AP isolation has to be enabled on one VLAN interface only.
This patch moves the AP isolation attribute to the per-vlan
interface attribute set, enabling it to have a different
value depending on the selected vlan.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
My university will stop email service for alumni in january 2014, please
use my new e-mail address instead.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Added power cap framework documentation. This explains the use of power
capping framework, sysfs and programming interface.
There are two documents:
- Documentation/power/powercap/powercap.txt : Explains use case and APIs.
- Documentation/ABI/testing/sysfs-class-powercap: Explains ABIs.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For some devices it is possible to configure a hysteresis for threshold (or
similar) events. This patch adds a new hysteresis event info type which allows
for easy creation and read/write handling of the sysfs attribute.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some links to projects web pages and e-mail addresses in ACPI/PM
documentation and Kconfig are outdated, so update them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
From this commit on f_mass_storage is available through configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The e-mail address rjw@sisk.pl that I have been using for quite some
time is going to expire at one point, so replace it with a new one,
rjw@rjwysocki.net, everywhere in MAINTAINERS and Documentation/ABI.
Signed-off-by: Rafael J. Wysocki <rjw@rjwysocki.net>
This patch enables support for OSPM suspend and resume in the MIC
driver. During a host suspend event, the driver performs an
orderly shutdown of the cards if they are online. Upon resume, any
cards that were previously online before suspend are rebooted.
The driver performs an orderly shutdown of the card primarily to
ensure that applications in the card are terminated and mounted
devices are safely un-mounted before the card is powered down in
the event of an OSPM suspend.
The driver makes use of the MIC daemon to accomplish OSPM suspend
and resume. The driver registers a PM notifier per MIC device.
The devices get notified synchronously during PM_SUSPEND_PREPARE and
PM_POST_SUSPEND phases.
During the PM_SUSPEND_PREPARE phase, the driver performs one of the
following three tasks.
1) If the card is 'offline', the driver sets the card to a
'suspended' state and returns.
2) If the card is 'online', the driver initiates card shutdown by
setting the card state to suspending. This notifies the MIC
daemon which invokes shutdown and sets card state to 'suspended'.
The driver returns after the shutdown is complete.
3) If the card is already being shutdown, possibly by a host user
space application, the driver sets the card state to 'suspended'
and returns after the shutdown is complete.
During the PM_POST_SUSPEND phase, the driver simply notifies the
daemon and returns. The daemon boots those cards that were previously
online during the suspend phase.
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Harshavardhan R Kharche <harshavardhan.r.kharche@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation says that the result of raw * scale should be in microvolts,
but in reallity all drivers actually report the scale so that the result is in
millivolts. So update the documentation to match reallity.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch enables the following features:
a) Boots and shuts down the card via sysfs entries.
b) Allocates and maps a device page for communication with the
card driver and updates the device page address via scratchpad
registers.
c) Provides sysfs entries for shutdown status, kernel command line,
ramdisk and log buffer information.
Co-author: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Caz Yokoyama <Caz.Yokoyama@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Harshavardhan R Kharche <harshavardhan.r.kharche@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch enables the following:
a) Initializes the Intel MIC X100 PCIe devices.
b) Provides sysfs entries for family and stepping information.
Co-author: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Signed-off-by: Caz Yokoyama <Caz.Yokoyama@intel.com>
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Harshavardhan R Kharche <harshavardhan.r.kharche@intel.com>
Signed-off-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Sudeep Dutt <sudeep.dutt@intel.com>
Acked-by: Yaozu (Eddie) Dong <eddie.dong@intel.com>
Reviewed-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allwinner has electric fuses (efuse) on their line of chips. This driver
reads those fuses, seeds the kernel entropy and exports them as a sysfs
node.
These fuses are most likely to be programmed at the factory, encoding
things like Chip ID, some sort of serial number, etc. and appear to be
reasonably unique.
While in theory, these should be writeable by the user, it will probably
be inconvenient to do so. Allwinner recommends that a certain input pin,
labeled 'efuse_vddq', be connected to GND. To write these fuses however,
a 2.5 V programming voltage needs to be applied to this pin.
Even so, they can still be used to generate a board-unique mac from,
board unique RSA key and seed the kernel RNG.
On sun7i additional storage is available, this is initially used for an
UEFI BOOT key, Secure JTAG key, HDMI-HDCP key and vendor specific keys.
Currently supported are the following known chips:
Allwinner sun4i (A10)
Allwinner sun5i (A10s, A13)
Allwinner sun7i (A20)
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of new drivers and some new functionality + a lot of cleanups
all over IIO.
New Core Elements
1) New INT_TIME info_mask element for integration time, which may have
different effects on measurement noise and similar, than an amplifier
and hence is different from existing SCALE. Already existed in some
drivers as a custom attribute.
2) Introduce a iio_push_buffers_with_timestamp helper to cover the common
case of filling the last 64 bits of data to be passed to the buffer with
a timestamp. Applied to lots of drivers. Cuts down on repeated code and
moves a slightly fiddly bit of logic into a single location.
3) Introduce info_mask_[shared_by_dir/shared_by_all] elements to allow support
of elements such as sampling_frequency which is typically shared by all
input channels on a device. This reduces code and makes these controls
available from in kernel consumers of IIO devices.
New drivers
1) MCP3422/3/4 ADC
2) TSL4531 ambient light sensor
3) TCS3472/5 color light sensor
4) GP2AP020A00F ambient light / proximity sensor
5) LPS001WP support added to ST pressure sensor driver.
New driver functionality
1) ti_am335x_adc Add buffered sampling support.
This device has a hardware fifo that is fed directly into an IIO kfifo
buffer based on a watershed interrupt. Note this will act as an example
of how to handle this increasingly common type of device.
The only previous example - sca3000 - take a less than optimal approach
which is largely why it is still in staging.
A couple of little cleanups for that new functionality followed later.
Core cleanups:
1) MAINTAINERS - Sachin actually brought my email address up to date because
I said I'd do it and never got around to it :)
2) Assign buffer list elements as single element lists to simplify the
iio_buffer_is_active logic.
3) wake_up_interruptible_poll instead of wake_up_interruptible to only wake
up threads waiting for poll notifications.
4) Add O_CLOEXEC flag to anon_inode_get_fd call for IIO event interface.
5) Change iio_push_to_buffers to take a void * pointer so as to avoid some
annoying and unnecessary type casts.
6) iio_compute_scan_bytes incorrectly took a long rather than unsigned long.
7) Various minor tidy ups.
Driver cleanups (in no particular order)
1) Another set of devm_ allocations patches from Sachin Kamat.
2) tsl2x7x - 0 to NULL cleanup.
3) hmc5843 - fix missing > in MODULE_AUTHOR
4) Set of strict_strto* to kstrto* conversions.
5) mxs-lradc - fix ordering of resource removal to match creation
6) mxs-lradc - add MODULE_ALIAS
7) adc7606 - drop a work pending test duplicated in core functions.
8) hmc5843 - devm_ allocation patch
9) Series of redundant breaks removed.
10) ad2s1200 - pr_err -> dev_err
11) adjd_s311 - use INT_TIME
12) ST sensors - large set of cleanups from Lee Jones and removed restriction
to using only triggers provided by the st_sensors themselves from
Dennis Ciocca.
13) dummy and tmp006 provide sampling_frequency via info_mask_shared_by_all.
14) tcs3472 - fix incorrect buffer size and wrong device pointer used in
suspend / resume functions.
15) max1363 - use defaults for buffer setup ops as provided by the triggered
buffer helpers as they are the same as were specified in max1363 driver.
16) Trivial tidy ups in a number of other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)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=mMgm
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, functionality and cleanups for IIO in the 3.13 cycle
A number of new drivers and some new functionality + a lot of cleanups
all over IIO.
New Core Elements
1) New INT_TIME info_mask element for integration time, which may have
different effects on measurement noise and similar, than an amplifier
and hence is different from existing SCALE. Already existed in some
drivers as a custom attribute.
2) Introduce a iio_push_buffers_with_timestamp helper to cover the common
case of filling the last 64 bits of data to be passed to the buffer with
a timestamp. Applied to lots of drivers. Cuts down on repeated code and
moves a slightly fiddly bit of logic into a single location.
3) Introduce info_mask_[shared_by_dir/shared_by_all] elements to allow support
of elements such as sampling_frequency which is typically shared by all
input channels on a device. This reduces code and makes these controls
available from in kernel consumers of IIO devices.
New drivers
1) MCP3422/3/4 ADC
2) TSL4531 ambient light sensor
3) TCS3472/5 color light sensor
4) GP2AP020A00F ambient light / proximity sensor
5) LPS001WP support added to ST pressure sensor driver.
New driver functionality
1) ti_am335x_adc Add buffered sampling support.
This device has a hardware fifo that is fed directly into an IIO kfifo
buffer based on a watershed interrupt. Note this will act as an example
of how to handle this increasingly common type of device.
The only previous example - sca3000 - take a less than optimal approach
which is largely why it is still in staging.
A couple of little cleanups for that new functionality followed later.
Core cleanups:
1) MAINTAINERS - Sachin actually brought my email address up to date because
I said I'd do it and never got around to it :)
2) Assign buffer list elements as single element lists to simplify the
iio_buffer_is_active logic.
3) wake_up_interruptible_poll instead of wake_up_interruptible to only wake
up threads waiting for poll notifications.
4) Add O_CLOEXEC flag to anon_inode_get_fd call for IIO event interface.
5) Change iio_push_to_buffers to take a void * pointer so as to avoid some
annoying and unnecessary type casts.
6) iio_compute_scan_bytes incorrectly took a long rather than unsigned long.
7) Various minor tidy ups.
Driver cleanups (in no particular order)
1) Another set of devm_ allocations patches from Sachin Kamat.
2) tsl2x7x - 0 to NULL cleanup.
3) hmc5843 - fix missing > in MODULE_AUTHOR
4) Set of strict_strto* to kstrto* conversions.
5) mxs-lradc - fix ordering of resource removal to match creation
6) mxs-lradc - add MODULE_ALIAS
7) adc7606 - drop a work pending test duplicated in core functions.
8) hmc5843 - devm_ allocation patch
9) Series of redundant breaks removed.
10) ad2s1200 - pr_err -> dev_err
11) adjd_s311 - use INT_TIME
12) ST sensors - large set of cleanups from Lee Jones and removed restriction
to using only triggers provided by the st_sensors themselves from
Dennis Ciocca.
13) dummy and tmp006 provide sampling_frequency via info_mask_shared_by_all.
14) tcs3472 - fix incorrect buffer size and wrong device pointer used in
suspend / resume functions.
15) max1363 - use defaults for buffer setup ops as provided by the triggered
buffer helpers as they are the same as were specified in max1363 driver.
16) Trivial tidy ups in a number of other drivers.
Integration time is in seconds; it controls the measurement
time and influences the gain of a sensor.
There are two typical ways that scaling is implemented in a device:
1) input amplifier,
2) reference to the ADC is changed.
These both result in the accuracy of the ADC varying (by applying its
sampling over a more relevant range).
Integration time is a way of dealing with noise inherent in the analog
sensor itself. In the case of a light sensor, a mixture of photon noise
and device specific noise. Photon noise is dealt with by either improving
the efficiency of the sensor, (more photons actually captured) which is not
easily varied dynamically, or by integrating the measurement over a longer
time period. Note that this can also be thought of as an averaging of a
number of individual samples and is infact sometimes implemented this way.
Altering integration time implies that the duration of a measurement changes,
a fact the device's user may be interested in.
Hence it makes sense to distinguish between integration time and simple
scale. In some devices both types of control are present and whilst they
will have similar effects on the amplitude of the reading, their effect
on the noise of the measurements will differ considerably.
Used by adjd_s311, tsl4531, tcs3472
The following drivers have similar controls (and could be adapted):
* tsl2563 (integration time is controlled via CALIBSCALE among other things)
* tsl2583 (has integration_time device_attr, but driver doesn't use channels yet)
* tsl2x7x (has integration_time attr)
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jon Brenner <jon.brenner@ams.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iEYEABECAAYFAlIt3VsACgkQdwG7hYl686NKBQCgqFzV1S+TiXZSjbqanK0374Hu
lMIAoI2IOQb1bgQFSqaOzgSaBmVhLtMc
=xWBt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd
Pull mtd updates from David Woodhouse:
- factor out common code from MTD tests
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc
* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
mtd: ofpart: use for_each_child_of_node() macro
mtd: mtdswap: replace strict_strtoul() with kstrtoul()
mtd cs553x_nand: use kzalloc() instead of memset
mtd: atmel_nand: fix error return code in atmel_nand_probe()
mtd: bcm47xxsflash: writing support
mtd: bcm47xxsflash: implement erasing support
mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
mtd: remove alauda driver
mtd: nand: mxc_nand: mark 'const' properly
mtd: maps: cfi_flagadm: add missing __iomem annotation
mtd: spear_smi: add missing __iomem annotation
mtd: r852: Staticize local symbols
mtd: nandsim: Staticize local symbols
mtd: impa7: add missing __iomem annotation
mtd: sm_ftl: Staticize local symbols
mtd: m25p80: add support for mr25h10
mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
mtd: m25p80: Pass flags through CAT25_INFO macro
...
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
This patch-set includes the following major enhancement patches.
o support inline xattrs
o add sysfs support to control GCs explicitly
o add proc entry to show the current segment usage information
o improve the GC/SSR performance
The other bug fixes are as follows.
o avoid the overflow on status calculation
o fix some error handling routines
o fix inconsistent xattr states after power-off-recovery
o fix incorrect xattr node offset definition
o fix deadlock condition in fsync
o fix the fdatasync routine for power-off-recovery
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YMk3
-----END PGP SIGNATURE-----
Merge tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"This patch-set includes the following major enhancement patches:
- support inline xattrs
- add sysfs support to control GCs explicitly
- add proc entry to show the current segment usage information
- improve the GC/SSR performance
The other bug fixes are as follows:
- avoid the overflow on status calculation
- fix some error handling routines
- fix inconsistent xattr states after power-off-recovery
- fix incorrect xattr node offset definition
- fix deadlock condition in fsync
- fix the fdatasync routine for power-off-recovery"
* tag 'for-f2fs-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (40 commits)
f2fs: optimize gc for better performance
f2fs: merge more bios of node block writes
f2fs: avoid an overflow during utilization calculation
f2fs: trigger GC when there are prefree segments
f2fs: use strncasecmp() simplify the string comparison
f2fs: fix omitting to update inode page
f2fs: support the inline xattrs
f2fs: add the truncate_xattr_node function
f2fs: introduce __find_xattr for readability
f2fs: reserve the xattr space dynamically
f2fs: add flags for inline xattrs
f2fs: fix error return code in init_f2fs_fs()
f2fs: fix wrong BUG_ON condition
f2fs: fix memory leak when init f2fs filesystem fail
f2fs: fix a compound statement label error
f2fs: avoid writing inode redundantly when creating a file
f2fs: alloc_page() doesn't return an ERR_PTR
f2fs: should cover i_xattr_nid with its xattr node page lock
f2fs: check the free space first in new_node_page
f2fs: clean up the needless end 'return' of void function
...
Here's the bit staging tree pull request for 3.12-rc1.
Lots of staging driver updates, and fixes. Lustre is finally enabled in
the build, and lots of cleanup started happening in it. There's a new
wireless driver in here, and 2 new TTY drivers, which cause the overall
lines added/removed to be quite large on the "added" side.
The IIO driver updates are also coming through here, as they are tied to
the staging iio drivers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIrEACgkQMUfUDdst+ynjqgCgjMpPlRkU1yzDCj8CnfoLUI+v
dIkAoLXD49aC8Km3f0LPUg/TgBA98MVx
=FLQ/
-----END PGP SIGNATURE-----
Merge tag 'staging-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree merge from Greg KH:
"Here's the bit staging tree pull request for 3.12-rc1.
Lots of staging driver updates, and fixes. Lustre is finally enabled
in the build, and lots of cleanup started happening in it. There's a
new wireless driver in here, and 2 new TTY drivers, which cause the
overall lines added/removed to be quite large on the "added" side.
The IIO driver updates are also coming through here, as they are tied
to the staging iio drivers"
* tag 'staging-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (942 commits)
staging: dwc2: make dwc2_core_params documentation more complete
staging: dwc2: validate the value for phy_utmi_width
staging: dwc2: interpret all hwcfg and related register at init time
staging: dwc2: properly mask the GRXFSIZ register
staging: dwc2: remove redundant register reads
staging: dwc2: re-use hptxfsiz variable
staging: dwc2: simplify debug output in dwc_hc_init
staging: dwc2: add missing shift
staging: dwc2: simplify register shift expressions
staging: dwc2: only read the snpsid register once
staging: dwc2: unshift non-bool register value constants
staging: dwc2: fix off-by-one in check for max_packet_count parameter
staging: dwc2: remove specific fifo size constants
Staging:BCM:DDRInit.c:Renaming __FUNCTION__
staging: bcm: remove Version.h file.
staging: rtl8188eu: off by one in rtw_set_802_11_add_wep()
staging: r8188eu: copying one byte too much
staging: rtl8188eu: || vs && typo
staging: r8188eu: off by one bugs
staging: crystalhd: Resolve sparse 'different base types' warnings.
...
We add a new sys node for ecc step size. So update the ABI document about it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
[Brian: edited description, modified 'ecc_strength']
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add description about in_accelX_power_mode and
in_accel_power_mode_available.
Signed-off-by: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Simple doc updates to zram documentation.
Signed-off-by: Bernhard M. Wiedemann <bwiedemann@suse.de>
Acked-by: Rob Landley <rob@landley.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Correct use of devnum in supports_autosuspend documentation, the sysfs path
contains busnum-port.port.port not busnum-devnum (which is the usb bus device
address).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sysfs entry gc_idle to control the gc policy. Where
gc_idle = 1 corresponds to selecting a cost benefit approach,
while gc_idle = 2 corresponds to selecting a greedy approach
to garbage collection. The selection is mutually exclusive one
approach will work at any point. If gc_idle = 0, then this
option is disabled.
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: change the select_gc_type() flow slightly]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Add sysfs entries to control the timing parameters for
f2fs gc thread.
Various Sysfs options introduced are:
gc_min_sleep_time: Min Sleep time for GC in ms
gc_max_sleep_time: Max Sleep time for GC in ms
gc_no_gc_sleep_time: Default Sleep time for GC in ms
Cc: Gu Zheng <guz.fnst@cn.fujitsu.com>
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Reviewed-by: Gu Zheng <guz.fnst@cn.fujitsu.com>
[Jaegeuk Kim: fix an umount bug and some minor changes]
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Pull block IO driver bits from Jens Axboe:
"As I mentioned in the core block pull request, due to real life
circumstances the driver pull request would be late. Now it looks
like -rc2 late... On the plus side, apart form the rsxx update, these
are all things that I could argue could go in later in the cycle as
they are fixes and not features. So even though things are late, it's
not ALL bad.
The pull request contains:
- Updates to bcache, all bug fixes, from Kent.
- A pile of drbd bug fixes (no big features this time!).
- xen blk front/back fixes.
- rsxx driver updates, some of them deferred form 3.10. So should be
well cooked by now"
* 'for-3.11/drivers' of git://git.kernel.dk/linux-block: (63 commits)
bcache: Allocation kthread fixes
bcache: Fix GC_SECTORS_USED() calculation
bcache: Journal replay fix
bcache: Shutdown fix
bcache: Fix a sysfs splat on shutdown
bcache: Advertise that flushes are supported
bcache: check for allocation failures
bcache: Fix a dumb race
bcache: Use standard utility code
bcache: Update email address
bcache: Delete fuzz tester
bcache: Document shrinker reserve better
bcache: FUA fixes
drbd: Allow online change of al-stripes and al-stripe-size
drbd: Constants should be UPPERCASE
drbd: Ignore the exit code of a fence-peer handler if it returns too late
drbd: Fix rcu_read_lock balance on error path
drbd: fix error return code in drbd_init()
drbd: Do not sleep inside rcu
bcache: Refresh usage docs
...
Pull x86 platform driver updates from Matthew Garrett:
"Nothing overly exciting here - a couple of new drivers that don't do a
great deal, along with some miscellaneous fixes and a couple of small
feature enablement patches"
* 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86:
x86 platform drivers: fix gpio leak
toshiba_acpi: Add dependency on SERIO_I8042
asus-nb-wmi: set wapf=4 for ASUSTeK COMPUTER INC. 1015E/U
Add trivial driver to disable Intel Smart Connect
Add support driver for Intel Rapid Start Technology
hp-wmi: add supports for POST code error
asus-wmi: control wlan-led only if wapf == 4
drivers/platform/x86/intel_ips: Convert to module_pci_driver
asus-nb-wmi: ignore ALS notification key code
asus-wmi: append newline to messages
x86: asus-laptop: fix invalid point access
x86: msi-laptop: fix memleak
amilo-rfkill: Add dependency on SERIO_I8042
dell-laptop: fix error return code in dell_init()
hp-wmi: Enable hotkeys on some systems
Pull perf fixes from Thomas Gleixner:
- fix for do_div() abuse on x86
- locking fix in perf core
- a pile of (build) fixes and cleanups in perf tools
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
perf/x86: Fix incorrect use of do_div() in NMI warning
perf: Fix perf_lock_task_context() vs RCU
perf: Remove WARN_ON_ONCE() check in __perf_event_enable() for valid scenario
perf: Clone child context from parent context pmu
perf script: Fix broken include in Context.xs
perf tools: Fix -ldw/-lelf link test when static linking
perf tools: Revert regression in configuration of Python support
perf tools: Fix perf version generation
perf stat: Fix per-socket output bug for uncore events
perf symbols: Fix vdso list searching
perf evsel: Fix missing increment in sample parsing
perf tools: Update symbol_conf.nr_events when processing attribute events
perf tools: Fix new_term() missing free on error path
perf tools: Fix parse_events_terms() segfault on error path
perf evsel: Fix count parameter to read call in event_format__new
perf tools: fix a typo of a Power7 event name
perf tools: Fix -x/--exclude-other option for report command
perf evlist: Enhance perf_evlist__start_workload()
perf record: Remove -f/--force option
perf record: Remove -A/--append option
...
- AF_IB (native IB addressing) for CMA from Sean Hefty
- New mlx5 driver for Mellanox Connect-IB adapters (including post merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- Resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- Other small changes and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nZh8
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- AF_IB (native IB addressing) for CMA from Sean Hefty
- new mlx5 driver for Mellanox Connect-IB adapters (including post
merge request fixes)
- SRP fixes from Bart Van Assche (including fix to first merge request)
- qib HW driver updates
- resurrection of ocrdma HW driver development
- uverbs conversion to create fds with O_CLOEXEC set
- other small changes and fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
mlx5: Return -EFAULT instead of -EPERM
IB/qib: Log all SDMA errors unconditionally
IB/qib: Fix module-level leak
mlx5_core: Adjust hca_cap.uar_page_sz to conform to Connect-IB spec
IB/srp: Let srp_abort() return FAST_IO_FAIL if TL offline
IB/uverbs: Use get_unused_fd_flags(O_CLOEXEC) instead of get_unused_fd()
mlx5_core: Fixes for sparse warnings
IB/mlx5: Make profile[] static in main.c
mlx5: Fix parameter type of health_handler_t
mlx5: Add driver for Mellanox Connect-IB adapters
IB/core: Add reserved values to enums for low-level driver use
IB/srp: Bump driver version and release date
IB/srp: Make HCA completion vector configurable
IB/srp: Maintain a single connection per I_T nexus
IB/srp: Fail I/O fast if target offline
IB/srp: Skip host settle delay
IB/srp: Avoid skipping srp_reset_host() after a transport error
IB/srp: Fix remove_one crash due to resource exhaustion
IB/qib: New transmitter tunning settings for Dell 1.1 backplane
IB/core: Fix error return code in add_port()
...
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
ignore that.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=OVO/
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Nothing interesting. Except the most embarrassing bugfix ever. But
let's ignore that"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: cleanup call chain.
module: do percpu allocation after uniqueness check. No, really!
modules: don't fail to load on unknown parameters.
ABI: Clarify when /sys/module/MODULENAME is created
There is no /sys/parameters
module: don't modify argument of module_kallsyms_lookup_name()
Intel Rapid Start Technology is a firmware-based suspend-to-disk
implementation. Once placed in S3, the device will wake once either a
timeout elapses or the battery reaches a critical level. It will then resume
to the firmware and copy the contents of RAM to a specialised partition, and
then power off the machine. If the user turns the machine back on the
firmware will copy the contents of the partition back to RAM and then resume
from S3 as normal.
This driver provides an interface for configuring the wakeup events and
timeout. It still requires firmware support and an appropriate suspend
partition.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
A new driver supports driving PWM signals using the TPU unit found on
various Renesas SoCs. Furthermore support is added for the NXP PCA9685
LED controller. Another big chunk is the sysfs interface which has been
in the works for quite some time.
The remaining patches are a random assortment of cleanups and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)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=5mly
-----END PGP SIGNATURE-----
Merge tag 'for-3.11-rc1' of git://gitorious.org/linux-pwm/linux-pwm
Pull pwm changes from Thierry Reding:
"A new driver supports driving PWM signals using the TPU unit found on
various Renesas SoCs. Furthermore support is added for the NXP
PCA9685 LED controller. Another big chunk is the sysfs interface
which has been in the works for quite some time.
The remaining patches are a random assortment of cleanups and fixes"
* tag 'for-3.11-rc1' of git://gitorious.org/linux-pwm/linux-pwm:
pwm: pwm-tiehrpwm: Use clk_enable/disable instead clk_prepare/unprepare.
pwm: pca9685: Fix wrong argument to set MODE1_SLEEP bit
pwm: renesas-tpu: Add MODULE_ALIAS to make module auto loading work
pwm: renesas-tpu: fix return value check in tpu_probe()
pwm: Add Renesas TPU PWM driver
pwm: Add sysfs interface
pwm: Fill in missing .owner fields
pwm: add pca9685 driver
pwm: atmel-tcb: prepare clk before calling enable
pwm: devm: alloc correct pointer size
pwm: mxs: Let device core handle pinctrl
MAINTAINERS: Update PWM subsystem entry
In the Power7 PMU guide:
https://www.power.org/documentation/commonly-used-metrics-for-performance-analysis/
PM_BRU_MPRED is referred to as PM_BR_MPRED.
It fixed the typo by changing the name of the event in kernel and
documentation accordingly.
This patch changes the ABI, there are some reasons I think it's ok:
- It is relatively new interface, specific to the Power7 platform.
- No tools that we know of actually use this interface at this point
(none are listed near the interface).
- Users of this interface (eg oprofile users migrating to perf)
would be more used to the "PM_BR_MPRED" rather than "PM_BRU_MPRED".
- These are in the ABI/testing at this point rather than ABI/stable,
so hoping we have some wiggle room.
Signed-off-by: Runzhen Wang <runzhen@linux.vnet.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Cc: icycoder@gmail.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Runzhen Wang <runzhew@clemson.edu>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Cc: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1372407297-6996-2-git-send-email-runzhen@linux.vnet.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pull HID updates from Jiri Kosina:
- HID battery handling cleanup by David Herrmann
- ELO 4000/4500 driver, which has been finally ported to be proper HID
driver by Jiri Slaby
- ps3remote driver functionality is now provided by generic sony
driver, by Jiri Kosina
- PS2/3 Buzz controllers support, by Colin Leitner
- rework of wiimote driver including full extensions hotpluggin
support, sub-device modularization and speaker support by David
Herrmann
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (55 commits)
HID: wacom: Intuos4 battery charging changes
HID: i2c-hid: support sending HID output reports using the output register
HID: kye: Add report fixup for Genius Gila Gaming mouse
HID: wiimote: support Nintendo Wii U Pro Controller
Input: make gamepad API keycodes more clear
input: document gamepad API and add extra keycodes
HID: explain out-of-range check better
HID: fix false positive out of range values
HID: wiimote: fix coccinelle warnings
HID: roccat: check cdev_add return value
HID: fold ps3remote driver into generic Sony driver
HID: hyperv: convert alloc+memcpy to memdup
HID: core: fix reporting of raw events
HID: wiimote: discard invalid EXT data reports
HID: wiimote: fix classic controller parsing
HID: wiimote: init EXT/MP during device detection
HID: wiimote: fix DRM debug-attr to correctly parse input
HID: wiimote: add MP quirks
HID: wiimote: remove old static extension support
HID: wiimote: add "bboard_calib" attribute
...
- Hotplug changes allowing device hot-removal operations to fail
gracefully (instead of crashing the kernel) if they cannot be
carried out completely. From Rafael J Wysocki and Toshi Kani.
- Freezer update from Colin Cross and Mandeep Singh Baines targeted
at making the freezing of tasks a bit less heavy weight operation.
- cpufreq resume fix from Srivatsa S Bhat for a regression introduced
during the 3.10 cycle causing some cpufreq sysfs attributes to
return wrong values to user space after resume.
- New freqdomain_cpus sysfs attribute for the acpi-cpufreq driver to
provide information previously available via related_cpus from
Lan Tianyu.
- cpufreq fixes and cleanups from Viresh Kumar, Jacob Shin,
Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia, Arnd Bergmann, and
Tang Yuantian.
- Fix for an ACPICA regression causing suspend/resume issues to
appear on some systems introduced during the 3.4 development cycle
from Lv Zheng.
- ACPICA fixes and cleanups from Bob Moore, Tomasz Nowicki, Lv Zheng,
Chao Guan, and Zhang Rui.
- New cupidle driver for Xilinx Zynq processors from Michal Simek.
- cpuidle fixes and cleanups from Daniel Lezcano.
- Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk.
- ACPI device power management fixes and cleanups from Fengguang Wu
and Rafael J Wysocki.
- ACPI documentation updates from Lv Zheng, Aaron Lu and Hanjun Guo.
- Fix for the IA-64 issue that was the reason for reverting commit
9f29ab1 and updates of the ACPI scan code from Rafael J Wysocki.
- Mechanism for adding CMOS RTC address space handlers from Lan Tianyu
(to allow some EC-related breakage to be fixed on some systems).
- Spec-compliant implementation of acpi_os_get_timer() from
Mika Westerberg.
- Modification of do_acpi_find_child() to execute _STA in order to
to avoid situations in which a pointer to a disabled device object
is returned instead of an enabled one with the same _ADR value.
From Jeff Wu.
- Intel BayTrail PCH (Platform Controller Hub) support for the ACPI
Intel Low-Power Subsystems (LPSS) driver and modificaions of that
driver to work around a couple of known BIOS issues from
Mika Westerberg and Heikki Krogerus.
- EC driver fix from Vasiliy Kulikov to make it use get_user() and
put_user() instead of dereferencing user space pointers blindly.
- Assorted ACPI code cleanups from Bjorn Helgaas, Nicholas Mazzuca and
Toshi Kani.
- Modification of the "runtime idle" helper routine to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows some code bloat
reduction to be done, from Rafael J Wysocki and Alan Stern.
- New trace points for PM QoS from Sahara <keun-o.park@windriver.com>.
- PM QoS documentation update from Lan Tianyu.
- Assorted core PM code cleanups and changes from Bernie Thompson,
Bjorn Helgaas, Julius Werner, and Shuah Khan.
- New devfreq driver for the Exynos5-bus device from Abhilash Kesavan.
- Minor devfreq cleanups, fixes and MAINTAINERS update from
MyungJoo Ham, Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and
Wei Yongjun.
- OMAP Adaptive Voltage Scaling (AVS) SmartReflex voltage control
driver updates from Andrii Tseglytskyi and Nishanth Menon.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=VBBq
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11dd ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
Pull perf updates from Ingo Molnar:
"Kernel improvements:
- watchdog driver improvements by Li Zefan
- Power7 CPI stack events related improvements by Sukadev Bhattiprolu
- event multiplexing via hrtimers and other improvements by Stephane
Eranian
- kernel stack use optimization by Andrew Hunter
- AMD IOMMU uncore PMU support by Suravee Suthikulpanit
- NMI handling rate-limits by Dave Hansen
- various hw_breakpoint fixes by Oleg Nesterov
- hw_breakpoint overflow period sampling and related signal handling
fixes by Jiri Olsa
- Intel Haswell PMU support by Andi Kleen
Tooling improvements:
- Reset SIGTERM handler in workload child process, fix from David
Ahern.
- Makefile reorganization, prep work for Kconfig patches, from Jiri
Olsa.
- Add automated make test suite, from Jiri Olsa.
- Add --percent-limit option to 'top' and 'report', from Namhyung
Kim.
- Sorting improvements, from Namhyung Kim.
- Expand definition of sysfs format attribute, from Michael Ellerman.
Tooling fixes:
- 'perf tests' fixes from Jiri Olsa.
- Make Power7 CPI stack events available in sysfs, from Sukadev
Bhattiprolu.
- Handle death by SIGTERM in 'perf record', fix from David Ahern.
- Fix printing of perf_event_paranoid message, from David Ahern.
- Handle realloc failures in 'perf kvm', from David Ahern.
- Fix divide by 0 in variance, from David Ahern.
- Save parent pid in thread struct, from David Ahern.
- Handle JITed code in shared memory, from Andi Kleen.
- Fixes for 'perf diff', from Jiri Olsa.
- Remove some unused struct members, from Jiri Olsa.
- Add missing liblk.a dependency for python/perf.so, fix from Jiri
Olsa.
- Respect CROSS_COMPILE in liblk.a, from Rabin Vincent.
- No need to do locking when adding hists in perf report, only 'top'
needs that, from Namhyung Kim.
- Fix alignment of symbol column in in the hists browser (top,
report) when -v is given, from NAmhyung Kim.
- Fix 'perf top' -E option behavior, from Namhyung Kim.
- Fix bug in isupper() and islower(), from Sukadev Bhattiprolu.
- Fix compile errors in bp_signal 'perf test', from Sukadev
Bhattiprolu.
... and more things"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (102 commits)
perf/x86: Disable PEBS-LL in intel_pmu_pebs_disable()
perf/x86: Fix shared register mutual exclusion enforcement
perf/x86/intel: Support full width counting
x86: Add NMI duration tracepoints
perf: Drop sample rate when sampling is too slow
x86: Warn when NMI handlers take large amounts of time
hw_breakpoint: Introduce "struct bp_cpuinfo"
hw_breakpoint: Simplify *register_wide_hw_breakpoint()
hw_breakpoint: Introduce cpumask_of_bp()
hw_breakpoint: Simplify the "weight" usage in toggle_bp_slot() paths
hw_breakpoint: Simplify list/idx mess in toggle_bp_slot() paths
perf/x86/intel: Add mem-loads/stores support for Haswell
perf/x86/intel: Support Haswell/v4 LBR format
perf/x86/intel: Move NMI clearing to end of PMI handler
perf/x86/intel: Add Haswell PEBS support
perf/x86/intel: Add simple Haswell PMU support
perf/x86/intel: Add Haswell PEBS record support
perf/x86/intel: Fix sparse warning
perf/x86/amd: AMD IOMMU Performance Counter PERF uncore PMU implementation
perf/x86/amd: Add IOMMU Performance Counter resource management
...
Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just removed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRsGMACgkQMUfUDdst+ylIIACfW8lLxOPVK+iYG699TWEBAkp0
LFEAnjlpAMJ1JnoZCuWDZObNCev93zGB
=020+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the big driver core merge for 3.11-rc1
Lots of little things, and larger firmware subsystem updates, all
described in the shortlog. Nice thing here is that we finally get rid
of CONFIG_HOTPLUG, after 10+ years, thanks to Stephen Rohtwell (it had
been always on for a number of kernel releases, now it's just
removed)"
* tag 'driver-core-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (27 commits)
driver core: device.h: fix doc compilation warnings
firmware loader: fix another compile warning with PM_SLEEP unset
build some drivers only when compile-testing
firmware loader: fix compile warning with PM_SLEEP set
kobject: sanitize argument for format string
sysfs_notify is only possible on file attributes
firmware loader: simplify holding module for request_firmware
firmware loader: don't export cache_firmware and uncache_firmware
drivers/base: Use attribute groups to create sysfs memory files
firmware loader: fix compile warning
firmware loader: fix build failure with !CONFIG_FW_LOADER_USER_HELPER
Documentation: Updated broken link in HOWTO
Finally eradicate CONFIG_HOTPLUG
driver core: firmware loader: kill FW_ACTION_NOHOTPLUG requests before suspend
driver core: firmware loader: don't cache FW_ACTION_NOHOTPLUG firmware
Documentation: Tidy up some drivers/base/core.c kerneldoc content.
platform_device: use a macro instead of platform_driver_register
firmware: move EXPORT_SYMBOL annotations
firmware: Avoid deadlock of usermodehelper lock at shutdown
dell_rbu: Select CONFIG_FW_LOADER_USER_HELPER explicitly
...
Here's the large staging tree merge for 3.11-rc1
Huge thing here is the Lustre client code. Unfortunatly, due to it not
building properly on a wide variety of different architectures (this was
production code???), it is currently disabled from the build so as to
not annoy people.
Other than Lustre, there are loads of comedi patches, working to clean
up that subsystem, iio updates and new drivers, and a load of cleanups
from the OPW applicants in their quest to get a summer internship.
All of these have been in the linux-next releases for a while (hence the
Lustre code being disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlHRsacACgkQMUfUDdst+yklBQCgzOUv0SlVYNhRj9KDDu1vxWTG
FnYAnRhRG9oXXkocjH6/cu+YOf21ClpZ
=WDt3
-----END PGP SIGNATURE-----
Merge tag 'staging-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree update from Greg KH:
"Here's the large staging tree merge for 3.11-rc1
Huge thing here is the Lustre client code. Unfortunatly, due to it
not building properly on a wide variety of different architectures
(this was production code???), it is currently disabled from the build
so as to not annoy people.
Other than Lustre, there are loads of comedi patches, working to clean
up that subsystem, iio updates and new drivers, and a load of cleanups
from the OPW applicants in their quest to get a summer internship.
All of these have been in the linux-next releases for a while (hence
the Lustre code being disabled)"
Fixed up trivial conflict in drivers/staging/serqt_usb2/serqt_usb2.c due
to independent renamings in the staging driver cleanup and the USB
tree..
* tag 'staging-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (868 commits)
Revert "Revert "Revert "staging/lustre: drop CONFIG_BROKEN dependency"""
staging: rtl8192u: fix line length in r819xU_phy.h
staging: rtl8192u: rename variables in r819xU_phy.h
staging: rtl8192u: fix comments in r819xU_phy.h
staging: rtl8192u: fix whitespace in r819xU_phy.h
staging: rtl8192u: fix newlines in r819xU_phy.c
staging: comedi: unioxx5: use comedi_alloc_spriv()
staging: comedi: unioxx5: fix unioxx5_detach()
silicom: checkpatch: errors caused by macros
Staging: silicom: remove the board_t typedef in bpctl_mod.c
Staging: silicom: capitalize labels in the bp_media_type enum
Staging: silicom: remove bp_media_type enum typedef
staging: rtl8192u: replace msleep(1) with usleep_range() in r819xU_phy.c
staging: rtl8192u: rename dwRegRead and rtStatus in r819xU_phy.c
staging: rtl8192u: replace __FUNCTION__ in r819xU_phy.c
staging: rtl8192u: limit line size in r819xU_phy.c
zram: allow request end to coincide with disksize
staging: drm/imx: use generic irq chip unused field to block out invalid irqs
staging: drm/imx: use generic irqchip
staging: drm/imx: ipu-dmfc: use defines for ipu channel numbers
...
/sys/module/MODULENAME is not created unconditionally. This can be
confusing so document the current conditions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Several InfiniBand HCAs allow configuring the completion vector per
CQ. This allows spreading the workload created by IB completion
interrupts over multiple MSI-X vectors and hence over multiple CPU
cores. In other words, configuring the completion vector properly not
only allows reducing latency on an initiator connected to multiple
SRP targets but also allows improving throughput.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* pm-cpufreq:
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
Konrad writes:
It has the 'feature-max-indirect-segments' implemented in both backend
and frontend. The current problem with the backend and frontend is that the
segment size is limited to 11 pages. It means we can at most squeeze in 44kB per
request. The ring can hold 32 (next power of two below 36) requests, meaning we
can do 1.4M of outstanding requests. Nowadays that is not enough.
The problem in the past was addressed in two ways - but neither one went upstream.
The first solution to this proposed by Justin from Spectralogic was to negotiate
the segment size. This means that the ‘struct blkif_sring_entry’ is now a variable size.
It can expand from 112 bytes (cover 11 pages of data - 44kB) to 1580 bytes
(256 pages of data - so 1MB). It is a simple extension by just making the array in the
request expand from 11 to a variable size negotiated. But it had limits: this extension
still limits the number of segments per request to 255 (as the total number must be
specified in the request, which only has an 8-bit field for that purpose).
The other solution (from Intel - Ronghui) was to create one extra ring that only has the
‘struct blkif_request_segment’ in them. The ‘struct blkif_request’ would be changed to have
an index in said ‘segment ring’. There is only one segment ring. This means that the size of
the initial ring is still the same. The requests would point to the segment and enumerate out
how many of the indexes it wants to use. The limit is of course the size of the segment.
If one assumes a one-page segment this means we can in one request cover ~4MB.
Those patches were posted as RFC and the author never followed up on the ideas on changing
it to be a bit more flexible.
There is yet another mechanism that could be employed (which these patches implement) - and it
borrows from VirtIO protocol. And that is the ‘indirect descriptors’. This very similar to
what Intel suggests, but with a twist. The twist is to negotiate how many of these
'segment' pages (aka indirect descriptor pages) we want to support (in reality we negotiate
how many entries in the segment we want to cover, and we module the number if it is
bigger than the segment size).
This means that with the existing 36 slots in the ring (single page) we can cover:
32 slots * each blkif_request_indirect covers: 512 * 4096 ~= 64M. Since we ample space
in the blkif_request_indirect to span more than one indirect page, that number (64M)
can be also multiplied by eight = 512MB.
Roger Pau Monne took the idea and implemented them in these patches. They work
great and the corner cases (migration between backends with and without this extension)
work nicely. The backend has a limit right now off how many indirect entries
it can handle: one indirect page, and at maximum 256 entries (out of 512 - so 50% of the page
is used). That comes out to 32 slots * 256 entries in a indirect page * 1 indirect page
per request * 4096 = 32MB.
This is a conservative number that can change in the future. Right now it strikes
a good balance between giving excellent performance, memory usage in the backend, and
balancing the needs of many guests.
In the patchset there is also the split of the blkback structure to be per-VBD.
This means that the spinlock contention we had with many guests trying to do I/O and
all the blkback threads hitting the same lock has been eliminated.
Also there are bug-fixes to deal with oddly sized sectors, insane amounts on
th ring, and also a security fix (posted earlier).
Commits fcf8058 (cpufreq: Simplify cpufreq_add_dev()) and aa77a52
(cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init())
changed the contents of the "related_cpus" sysfs attribute on systems
where acpi-cpufreq is used and user space can't get the list of CPUs
which are in the same hardware coordination CPU domain (provided by
the ACPI AML method _PSD) via "related_cpus" any more.
To make up for that loss add a new sysfs attribute "freqdomian_cpus"
for the acpi-cpufreq driver which exposes the list of CPUs in the
same domain regardless of whether it is coordinated by hardware or
software.
[rjw: Changelog, documentation]
References: https://bugzilla.kernel.org/show_bug.cgi?id=58761
Reported-by: Jean-Philippe Halimi <jean-philippe.halimi@exascale-computing.eu>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add documenation for new ABI entries.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a simple sysfs interface to the generic PWM framework.
/sys/class/pwm/
`-- pwmchipN/ for each PWM chip
|-- export (w/o) ask the kernel to export a PWM channel
|-- npwm (r/o) number of PWM channels in this PWM chip
|-- pwmX/ for each exported PWM channel
| |-- duty_cycle (r/w) duty cycle (in nanoseconds)
| |-- enable (r/w) enable/disable PWM
| |-- period (r/w) period (in nanoseconds)
| `-- polarity (r/w) polarity of PWM (normal/inversed)
`-- unexport (w/o) return a PWM channel to the kernel
Based on work by Lars Poeschel.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Ryan Mallon <rmallon@gmail.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add initial ABI documentation for ACPI devices' sysfs interfaces.
Contacts information fields are filled with current ACPI maintainer and the
relevant authors are carbon copied.
[rjw: Use my e-mail address that's likely to be valid longer.]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=O9AH
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
update ABI documentation with current paths related to scan_elements folder
Paths changed long time ago in commit: 26d25ae3f0
Signed-off-by: Alexandre Relange <alexandre@relange.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
f_rndis learns about configfs so we can, eventually,
remove in-kernel gadget drivers.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
f_subset learns about configfs so we can, eventually,
remove in-kernel gadget drivers.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Alex Williamson