For IPs which have alias algorightm all the time using that alias and
minor number. It means serial20 alias ends up as ttyPS20.
If alias is not setup for probed IP instance the first unused position is
used but that needs to be checked if it is really empty because another
instance doesn't need to be probed at that time. of_alias_get_alias_list()
fills alias bitmap which exactly shows which ID is free.
If alias pointing to different not compatible IP, it is free to use.
cdns_get_id() call is placed below structure allocation to simplify
error path.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/tty/serial/pmac_zilog.c: In function 'pmz_receive_chars':
drivers/tty/serial/pmac_zilog.c:222:30: warning:
variable 'error' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After 2dd4531686 ("kgdboc: Fix restrict error"), kgdboc_option_setup is
now only used when built in, resulting in a warning when compiled as a
module:
drivers/tty/serial/kgdboc.c:134:12: warning: 'kgdboc_option_setup' defined but not used [-Wunused-function]
static int kgdboc_option_setup(char *opt)
^~~~~~~~~~~~~~~~~~~
Move the function under the appropriate ifdef for builtin only.
Fixes: 2dd4531686 ("kgdboc: Fix restrict error")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS752 has an Enhanced Feature Register which is aliased at the
same address as the Interrupt Identification Register; accessing it
requires that a magic value is written to the Line Configuration
Register. If an interrupt is raised while the EFR is mapped in then
the ISR won't be able to access the IIR, leading to the "Unexpected
interrupt" error messages.
Avoid the problem by claiming a mutex around accesses to the EFR
register, also claiming the mutex in the interrupt handler work
item (this is equivalent to disabling interrupts to interlock against
a non-threaded interrupt handler).
See: https://github.com/raspberrypi/linux/issues/2529
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SC16IS752 is a dual-channel device. The two channels are largely
independent, but the IRQ signals are wired together as an open-drain,
active low signal which will be driven low while either of the
channels requires attention, which can be for significant periods of
time until operations complete and the interrupt can be acknowledged.
In that respect it is should be treated as a true level-sensitive IRQ.
The kernel, however, needs to be able to exit interrupt context in
order to use I2C or SPI to access the device registers (which may
involve sleeping). Therefore the interrupt needs to be masked out or
paused in some way.
The usual way to manage sleeping from within an interrupt handler
is to use a threaded interrupt handler - a regular interrupt routine
does the minimum amount of work needed to triage the interrupt before
waking the interrupt service thread. If the threaded IRQ is marked as
IRQF_ONESHOT the kernel will automatically mask out the interrupt
until the thread runs to completion. The sc16is7xx driver used to
use a threaded IRQ, but a patch switched to using a kthread_worker
in order to set realtime priorities on the handler thread and for
other optimisations. The end result is non-threaded IRQ that
schedules some work then returns IRQ_HANDLED, making the kernel
think that all IRQ processing has completed.
The work-around to prevent a constant stream of interrupts is to
mark the interrupt as edge-sensitive rather than level-sensitive,
but interpreting an active-low source as a falling-edge source
requires care to prevent a total cessation of interrupts. Whereas
an edge-triggering source will generate a new edge for every interrupt
condition a level-triggering source will keep the signal at the
interrupting level until it no longer requires attention; in other
words, the host won't see another edge until all interrupt conditions
are cleared. It is therefore vital that the interrupt handler does not
exit with an outstanding interrupt condition, otherwise the kernel
will not receive another interrupt unless some other operation causes
the interrupt state on the device to be cleared.
The existing sc16is7xx driver has a very simple interrupt "thread"
(kthread_work job) that processes interrupts on each channel in turn
until there are no more. If both channels are active and the first
channel starts interrupting while the handler for the second channel
is running then it will not be detected and an IRQ stall ensues. This
could be handled easily if there was a shared IRQ status register, or
a convenient way to determine if the IRQ had been deasserted for any
length of time, but both appear to be lacking.
Avoid this problem (or at least make it much less likely to happen)
by reducing the granularity of per-channel interrupt processing
to one condition per iteration, only exiting the overall loop when
both channels are no longer interrupting.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 FIFOs indeed need to be cleared after stopping transmission in
RS485 mode without SER_RS485_RX_DURING_TX flag set. But there are two
problems with the approach taken by the previous patch from Fixes tag.
First, serial8250_clear_fifos() should clear fifos, but what it really
does is it enables the FIFOs unconditionally if present, clears them
and then sets the FCR register to zero, which effectively disables the
FIFOs. In case the FIFO is disabled, enabling it and clearing it makes
no sense and in fact can trigger misbehavior of the 8250 core. Moreover,
the FCR register may contain other FIFO configuration bits which may not
be writable unconditionally and writing them incorrectly can trigger
misbehavior of the 8250 core too. (ie. AM335x UART swallows the first
byte and retransmits the last byte twice because of this FCR write).
Second, serial8250_clear_and_reinit_fifos() completely reloads the FCR,
but what really has to happen at the end of the RS485 transmission is
clearing of the FIFOs and nothing else.
This patch repairs serial8250_clear_fifos() so that it really only
clears the FIFOs by operating on FCR[2:1] bits and leaves all the
other bits alone. It also undoes serial8250_clear_and_reinit_fifos()
from __do_stop_tx_rs485() as serial8250_clear_fifos() is sufficient.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: 2bed8a8e70 ("Clearing FIFOs in RS485 emulation mode causes subsequent transmits to break")
Cc: Daniel Jedrychowski <avistel@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # let it bake a bit before merging
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ"), a
check was added for the UART driver being probed prior to the parent IRQ
controller.
Unfortunately this breaks certain boards which have no interrupt support,
like Huawei D03.
Indeed, the 8250 DT bindings state that interrupts should be supported -
not must.
To fix, switch from irq_of_parse_and_map() to of_irq_get(), which
does relay whether the IRQ host controller domain is not ready, i.e.
defer probe, instead of assuming it.
Fixes: c58caaab3b ("serial: 8250: of: Defer probe on missing IRQ")
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If you've got the "console" serial port setup to use just as a UART
(AKA there is no "console=ttyMSMX" on the kernel command line) then
certain initialization is skipped. When userspace later tries to do
something with the port then things go boom (specifically, on my
system, some sort of exception hit that caused the system to reboot
itself w/ no error messages).
Let's cleanup / refactor the init so that we always run the same init
code regardless of whether we're using the console.
To make this work, we make rely on qcom_geni_serial_pm doing its job
to turn resources on.
For the record, here is a trace of the order of things (after this
patch) when console= is specified on the command line and we have an
agetty on the port:
qcom_geni_serial_pm: 4 (undefined) => 0 (on)
qcom_geni_console_setup
qcom_geni_serial_port_setup
qcom_geni_serial_console_write
qcom_geni_serial_startup
qcom_geni_serial_start_tx
...and here is the order of things (after this patch) when console= is
_NOT_ specified on the command line and we have an agetty port:
qcom_geni_serial_pm: 4 => 0
qcom_geni_serial_pm: 0 => 3
qcom_geni_serial_pm: 3 => 0
qcom_geni_serial_startup
qcom_geni_serial_port_setup
qcom_geni_serial_pm: 0 => 3
qcom_geni_serial_pm: 3 => 0
qcom_geni_serial_startup
qcom_geni_serial_start_tx
Fixes: c4f528795d ("tty: serial: msm_geni_serial: Add serial driver support for GENI based QUP")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With gcc 4.1.2:
drivers/tty/serial/qcom_geni_serial.c: In function ‘qcom_geni_serial_probe’:
drivers/tty/serial/qcom_geni_serial.c:1261: warning: ‘drv’ may be used uninitialized in this function
Indeed, if dev.of_node is NULL, drv will be used uninitialized, and
dereferenced in uart_add_one_port(). However, as this driver supports
DT only, dev.of_node will always be valid.
Hence remove the useless check for dev.of_node, killing the warning as a
side effect.
Fixes: 8a8a66a1a1 ("tty: serial: qcom_geni_serial: Add support for flow control")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the error path of mxs_auart_request_gpio_irq() is performed
backward iterating with index i of enum type. Underline enum type
may be unsigned char. In this case check (--i >= 0) will be always
true and error handling goes into infinite loop.
The patch changes the check so that it is valid for signed and unsigned
types.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make the macros' definition and code have the same correct indentation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register offset value should be 'unsigned int' type.
Moreover, prefer 'unsigned int' to bare use of 'unsigned'.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The devm_ioremap_resource() will valid the resources, thus remove the
unnecessary resource validation in the driver.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define readable macros instead of magic number to make code more readable.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Acked-by: Chunyan Zhang <chunyan.zhang@spreadtrum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow 8250 omap serial driver to be used for K3 platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that the baud clock is also enabled for UART register writes in
driver resume. On Exynos5433 SoC this is needed to avoid external abort
issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the register offsets are different for RZ/A2 SCIF, we need
to declare a separate string for it.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2d4dd0da45.
This broke earlycon on all Renesas ARM platforms using a SCIF port for the
serial console (R-Car, RZ/A1, RZ/G1, RZ/G2 SoCs), due to an incorrect value
of port->regshift.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some i.MX SoCs' low power mode, such as i.MX7D's LPSR(low power
state retention), UART iomux settings will be lost, need to add
pinctrl sleep/default mode switch during suspend/resume to make
sure UART iomux settings are correct after resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In noirq suspend/resume stage with no_console_suspend enabled,
imx_uart_console_write() may be called to print out log_buf
message by printk(), so there will be race condition between
imx_uart_console_write() and imx_uart_save/restore_context(),
need to add lock to protect the registers save/restore operations.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the program enters the uart ISR, the local interrupt has been
disabled by the system, so it's not appropriate to use spin_lock_irqsave
interface in the ISR.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver console functions are using pointer to static array with fixed
size. There can be only one serial console at the time which is found
by register_console(). register_console() is filling cons->index to
port->line value.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_console is called twice once from
uart_add_one_port -> uart_configure_port
remove the double call
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move uart register to probe.
This is in preparation of removing the hardcoding of number of uarts.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At probe the uartlite is getting configured.
Enable the clocks before assiging uart and
disable after probe is done.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The printk() in serial8250_interrupt() was once hidden behind a debug
macro in commit f4f653e987 ("serial: 8250, disable "too much work"
messages") and reverted back in commit 12de375ec4 ("Revert "serial:
8250, disable "too much work" messages"").
This was introduced first in 0.99.13k with the "serial" driver itself
(and called pass_number with a limit of 64 and no print). In 1.1.13 it
was renamed to pass_counter and the printk was behind #if 0. In 1.1.94
the limit of 64 was increased to 256 and hidden behind
RS_ISR_PASS_LIMIT. With this change the #if 0 turned into #if 1. It
slowly become what we have today with a loop limit of 512.
Usually, that printk isn't hit. However on KVM with a busy UART and
overloaded host it might happen. It is also likely with threaded
interrupts and a task which preempts the interrupt handler.
If the UART has (legitimate) work to do and we break out of the loop,
nothing changes: the interrupt is most likely already pending in the
interrupt controller and we end up in the handler anyway. This printk is
hardly helping.
Older kernels also had a comment saying that a bad configuration might
lead to this but I don't see how that should happen because a wrongly
configured interrupt number would let the handler leave "early" with
IRQ_NONE and the spurious detected will handle that (weill since 2.6.11,
before that we had no spurious detector). In that case, we would never
loop that often here.
This loop looks like an optimisation in order to pull the bytes from the
FIFO which were received while we were already here instead of waiting
for the interrupt. This might have been a good idea while the CPUs were
slow and FIFOs small.
There are other serial driver in tree, like the amba-pl*, which also
have this kind of a loop but without the printk (and were based on this
driver).
Remove the printk which might trigger in otherwise valid situtations.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's an error when compiled with restrict:
drivers/tty/serial/kgdboc.c: In function ‘configure_kgdboc’:
drivers/tty/serial/kgdboc.c:137:2: error: ‘strcpy’ source argument is the same
as destination [-Werror=restrict]
strcpy(config, opt);
^~~~~~~~~~~~~~~~~~~
As the error implies, this is from trying to use config as both source and
destination. Drop the call to the function where config is the argument
since nothing else happens in the function.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pr_* is preferred according to scripts/checkpatch.pl.
Cc: jason.wessel@windriver.com
Cc: gregkh@linuxfoundation.org
Cc: jslaby@suse.com
Signed-off-by: He Zhe <zhe.he@windriver.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdboc_option_setup does not check input argument before passing it
to strlen. The argument would be a NULL pointer if "ekgdboc", without
its value, is set in command line and thus cause the following panic.
PANIC: early exception 0xe3 IP 10:ffffffff8fbbb620 error 0 cr2 0x0
[ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 4.18-rc8+ #1
[ 0.000000] RIP: 0010:strlen+0x0/0x20
...
[ 0.000000] Call Trace
[ 0.000000] ? kgdboc_option_setup+0x9/0xa0
[ 0.000000] ? kgdboc_early_init+0x6/0x1b
[ 0.000000] ? do_early_param+0x4d/0x82
[ 0.000000] ? parse_args+0x212/0x330
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_options+0x20/0x23
[ 0.000000] ? rdinit_setup+0x26/0x26
[ 0.000000] ? parse_early_param+0x2d/0x39
[ 0.000000] ? setup_arch+0x2f7/0xbf4
[ 0.000000] ? start_kernel+0x5e/0x4c2
[ 0.000000] ? load_ucode_bsp+0x113/0x12f
[ 0.000000] ? secondary_startup_64+0xa5/0xb0
This patch adds a check to prevent the panic.
Cc: stable@vger.kernel.org
Cc: jason.wessel@windriver.com
Cc: gregkh@linuxfoundation.org
Cc: jslaby@suse.com
Signed-off-by: He Zhe <zhe.he@windriver.com>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable automatic flow control which should ensure that there is no
mainteinance in connection for zcu100 BT case.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Record port ID in device data structure to be have it connected to
certain instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Every instance is registering own struct console and struct uart_driver
with minor number which corresponds to alias ID (or 0 now) and with 1 uart
port. The same alias ID is saved to tty_driver->name_base which is key
field for creating ttyPSX name.
Because name_base and minor number are setup already there is no need to
setup any port->line number because 0 is the right value.
Unfortunately this driver is setting up major number to 0 for using
dynamic assignment and kernel is allocating different major numbers for
every instance instead of using the same major and different minor
number.
~# ls -la /dev/ttyPS*
crw------- 1 root root 252, 0 Jan 1 03:36 /dev/ttyPS0
crw--w---- 1 root root 253, 1 Jan 1 00:00 /dev/ttyPS1
When major number is not 0. For example 252 then major/minor
combinations are in expected form
~# ls -la /dev/ttyPS*
crw------- 1 root root 252, 0 Jan 1 04:04 /dev/ttyPS0
crw--w---- 1 root root 252, 1 Jan 1 00:00 /dev/ttyPS1
Driver is not freeing struct cdns_uart_console in case that instance is
not used as console. The reason is that console is incorrectly unregistred
and "console [0] disabled" message will be shown.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change logic how console_port is setup by using CON_ENABLED flag
instead of index. There will be unique cdns_uart_console() structures
that's why code can't use id for console_port assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is preparation step for dynamic port allocation without
CDNS_UART_NR_PORTS macro. Fill the structure only once at probe.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register uart driver in probe to be able to register one device with
unique major/minor separately. Also calculate number of instances of
this driver to be able to call uart_unregister_driver() when there is no
instance.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This cosmetic change is done only for having next patch much easier to
read. Moving id setup higher in probe is not affecting any usage of this
driver and it also simplify error path.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cdns_uart_suspend()/resume() and remove() are using static reference
to struct uart_driver. Assign this reference to private data structure
as preparation step for dynamic struct uart_driver allocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's suspend/resume functions were buggy.
If UART node contains any child node in the DT and
the child is established a communication path with
the parent UART. The relevant /dev/ttyPS* node will
be not available for other operations.
If the driver is trying to do any operations like
suspend/resume without checking the tty->dev status
it leads to the kernel crash/hang.
This patch fix this issue by call the device_may_wake()
with the generic parameter of type struct device.
in the uart suspend and resume paths.
It also fixes a race condition in the uart suspend
path(i.e uart_suspend_port() should be called at the
end of cdns_uart_suspend API this path updates the same)
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Writing zero and NULLs to already initialized fields is not needed.
Remove this additional writes.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When console device is rebinded, console_setup() is called again.
But marking it as __init means that function will be clear after boot is
complete. If console device is binded again console_setup() is not found
and error "Unable to handle kernel paging request at virtual address"
is reported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.
Fixes: f5316b4aea ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.
Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.
Cc: stable@vger.kernel.org # v4.9+
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, this driver (or the hardware) does not support character
length settings. It's apparently running in 8-bit mode, but it makes
userspace believe it's in 5-bit mode. That makes tcsetattr with CS8
incorrectly fail, breaking e.g. getty from busybox, thus the login shell
on ttyMVx.
Fix by hard-wiring CS8 into c_cflag.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch modifies the place where resources and device tree properties
are searched.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
Revert commit ecb988a3b7985913d1f0112f66667cdd15e40711: tty: serial:
8250: 8250_core: NXP SC16C2552 workaround
The above commit causes userland application to no longer write
correctly its first write to a dumb terminal connected to /dev/ttyS0.
This commit seems to be the culprit. It's as though the TX FIFO is being
reset during that write. What should be displayed is:
PSW 80000000 INST 00000000 HALT
//
What is displayed is some variation of:
T 00000000 HAL//
Reverting this commit via this patch fixes my problem.
Signed-off-by: Mark Hounschell <dmarkh@cfl.rr.com>
Fixes: ecb988a3b7 ("tty: serial: 8250: 8250_core: NXP SC16C2552 workaround")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sleep wake-up refactoring that I introduced in
commit c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
did not account for devices with a slave device on the expansion port.
This patch pokes the INT0 register in the slave device, if present, in
order to ensure that MSI interrupts don't get permanently "stuck"
because of a sleep wake-up interrupt as described here:
commit 2c0ac5b48a ("serial: exar: Fix stuck MSIs")
This also converts an ioread8() to readb() in order to provide visual
consistency with the MMIO-only accessors used elsewhere in the driver.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Fixes: c7e1b40590 ("tty: serial: exar: Relocate sleep wake-up handling")
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add ACPI identifier HID for UART DW 8250 on Broadcom SoCs
to match the HID passed through ACPI tables to enable
UART controller.
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Tested-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is
NULL. This happens during resume.
Call Trace:
...
[ 54.928108] dw8250_set_termios+0x162/0x170
[ 54.928114] serial8250_set_termios+0x17/0x20
[ 54.928117] uart_change_speed+0x64/0x160
[ 54.928119] uart_resume_port
...
So the baud rate is not restored after S3 and breaks the apps who use
UART, for example, console and bluetooth etc.
We address this issue by setting the baud rate irrespective of arg
"old", just like the drivers for other 8250 IPs. This is tested with
Intel Broxton platform.
Signed-off-by: Chen Hu <hu1.chen@intel.com>
Fixes: 4e26b134bd ("serial: 8250_dw: clock rate handling for all ACPI platforms")
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support of Common Clock Framework for Uartlite driver.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add struct uartlite_data, to store the private data of the Uartlite
driver.
Signed-off-by: Tanvi Desai <tanvi.desai@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SCIF versions mux error and break interrupts together and then provide
a separate interrupt ID for just TEI/DRI.
Allow all 6 types of interrupts to be specified via platform data (or DT)
and for any signals that are muxed together (have the same interrupt
number) simply register one handler.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no more need for SCIx_RZ_SCIFA_REGTYPE now that
SCIx_SH4_SCIF_REGTYPE can provide the same register/address definitions.
Also, R7S9210 no longer needs a special compatible since the standard
"renesas,scif" will work just fine.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices with SCIx_SH4_SCIF_REGTYPE have no space between registers.
Use the register area size to determine the spacing between register.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since we have port name stored in struct uart_port, we better to use
that one instead of open coding.
This will make it one place source for easier maintenance or
modifications.
While here, replace printk_ratelimited(KERN_INFO ) by pr_info_ratelimited().
It seems last printk() call in 8250_port.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No later code uses the assigned value, so it can be dropped.
Reported-by: Simon Horman <horms@verge.net.au>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Describe all memebers in struct exar8250_board, otherwise we get a warning:
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'has_slave' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'setup' not described in 'exar8250_board'
drivers/tty/serial/8250/8250_exar.c:122: warning: Function parameter or member 'exit' not described in 'exar8250_board'
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exar UARTs by default supports only up to 8 channels,
all above go as extension. Thus, there is no need to have
an additional property to distinguish them from first ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Renesas RZ/N1 UART is based on the Synopsys DW UART, but has additional
registers for DMA. This patch does not address the changes required for DMA
support, it simply adds the compatible string.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sci_request_irq() checks port->irqstr[j] for a NULL pointer, to decide
if a fallback interrupt name string should be allocated or not.
While this string is freed during port shutdown, the pointer is not
zeroed. Hence on a subsequent startup of the port, it will still be
pointing to the freed memory, leading to e.g.
WARNING: CPU: 0 PID: 404 at fs/proc/generic.c:388 __proc_create+0xbc/0x260
name len 0
or to a crash (the latter is more likely with CONFIG_DEBUG_SLAB=y, due
to the poisoning of freed memory).
Instead of zeroeing the pointer at multiple places, preinitialize
port->irqstr[j] to zero to fix this.
Fixes: 8b0bbd9562 ("serial: sh-sci: Add support for R7S9210")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for flow control functionality in the GENI serial driver
and also support for non-console higher baud rate(upto 4Mbps) usecases.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Mohammed Khajapasha <mkhaja@codeaurora.org>
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the IRQ controller is not yet probed do not proceed with irq=0,
try to defer the probe.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't dispose IRQ mapping before it has been created.
Fixes: aa9594740 ("serial: 8250_of: Add IO space support")
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for a "RZ_SCIFA" which is different than a traditional
SCIFA. It looks like a normal SCIF with FIFO data, but with a
compressed address space. Also, the break out of interrupts
are different then traditinal SCIF: ERI/BRI, RXI, TXI, TEI, DRI.
The R7S9210 (RZ/A2) contains this type of SCIF.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer ch is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'ch' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Synopsys DesignWare 8250 uart which version >= 4.00a, there's a
valid divisor latch fraction register. The fractional divisor width is
4bits ~ 6bits.
Now the preparation is done, it's easy to add the feature support.
This patch firstly tries to get the fractional divisor width during
probe, then setups dw specific get_divisor() and set_divisor() hook.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add these two hooks so that they can be overridden with driver specific
implementations.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several extended (in comparison to the traditional 16550)
registers are present in Synopsys DesignWare UART. All of them
are 32-bit ones.
Introduce helpers to simplify access to them and convert existing users.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Align serial8250_get_divisor() with serial8250_set_divisor() to accept
uart_port pointer as the first parameter. No functionality changes.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As of commit b36f09c3c4 ("dmaengine: Add transfer termination
synchronization support"), dmaengine_terminate_all() is deprecated.
Replace calls to dmaengine_terminate_all() in DMA release code by calls
to dmaengine_terminate_sync(), as the latter waits until all running
completion callbacks have finished.
Replace calls to dmaengine_terminate_all() in DMA failure paths by calls
to dmaengine_terminate_async(), as these are usually done in atomic
context.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmit DMA workqueue is never stopped, hence the work function may
be called after the port has been shut down.
Fix this race condition by cancelling queued work, if any, before DMA
release. Don't initialize the work if DMA initialization failed, as it
won't be used anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the sh-sci driver detects an issue with DMA during operation, it
falls backs to PIO, and releases all DMA resources.
As releasing DMA resources immediately has no advantages, but
complicates the code, and is susceptible to races, it is better to
postpone this to port shutdown.
This allows to remove the locking from sci_rx_dma_release() and
sci_tx_dma_release(), but requires keeping a copy of the DMA channel
pointers for release during port shutdown.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX FIFO timer may be armed when the port is shut down, hence the
timer function may still be called afterwards.
Fix this race condition by deleting the timer during port shutdown.
Fixes: 039403765e ("serial: sh-sci: SCIFA/B RX FIFO software timeout")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the commit
7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
pure serial multi-port cards, such as CH355, got blacklisted and thus
not being enumerated anymore. Previously, it seems, blacklisting them
was on purpose to shut up pciserial_init_one() about record duplication.
So, remove the entries from blacklist in order to get cards enumerated.
Fixes: 7d8905d064 ("serial: 8250_pci: Enable device after we check black list")
Reported-by: Matt Turner <mattst88@gmail.com>
Cc: Sergej Pupykin <ml@sergej.pp.ru>
Cc: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-and-Tested-by: Matt Turner <mattst88@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This writel writes the exact same value as the previous writel and is
thus unnecessary. It accidentally became unnecessary in e3538c37ee
("tty: xuartps: Beautify read-modify writes"), but the new behaviour is
now expected.
Link: https://www.spinics.net/lists/linux-serial/msg23168.html
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After sending data to the uart, the driver was waiting until the TX
FIFO was empty (for every single char written). After that, TX was
disabled by writing the original TX state to the status register. At
that time however, the state machine could still be shifting
characters. Not waiting can result in strange hardware states,
especially when coupled with calls to cdns_uart_set_termios, whose
symptom generally is garbage characters being received from uart or a
hang.
According to UG585, the TACTIVE bit of the channel status register
indicates the shifter operation and we should be waiting for that bit
to clear.
Sending characters does not require the TX FIFO to be empty, but merely
to not be full. So cdns_uart_console_putchar is updated accordingly.
During tests with an instrumented kernel and an oscilloscope, we could
determine that the chance of a race is reduced by this patch. It is not
removed entirely. On the oscilloscope, one can see that disabling the
transmitter early can result in the transmission hanging in the middle
of a character for a tiny duration. This hiccup is enough to
desynchronize with a remote device for a sequence of characters until a
data bit doesn't match the start or stop bits anymore.
Link: https://www.spinics.net/lists/linux-serial/msg23156.html
Link: https://www.spinics.net/lists/linux-serial/msg26139.html
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit mask changes in commit 6e14f7c1f2 ("tty: xuartps: Improve
startup function") doesn't do what the commit message advertises. The
original behaviour was clearing the RX_DIS bit, but due to missing ~,
that bit is now the only bit kept.
Currently, the regression is harmless, because the previous write to the
control register sets it to TXRST | RXRST. Thus the RX_DIS bit is
previously cleared. The *RST bits are cleared by the hardware, so this
commit does not currently change behaviour, but makes future changes
less risky.
Link: https://www.spinics.net/lists/linux-serial/msg23157.html
Signed-off-by: Helmut Grohne <h.grohne@intenta.de>
Fixes: 6e14f7c1f2 ("tty: xuartps: Improve startup function")
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pcmcia_loop_config fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling pcmcia_loop_config.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AM654 uses a UART controller that is compatible (partially) with
existing 8250 UART, however, has a few differences with respect to DMA
support and control paths. Introduce a base definition that allows us
to build up the differences in follow on patches.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the non-board-specific part of the RS485 initialization from
iot2040_rs485_config function to a new generic function used also for
other boards.
This allows using TIOCGRS485 and TIOCSRS485 on boards (such as mPCIe
serial IO modules) which are hard-wired to RS485 or have jumpers for
their configurations.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If port.line is out of range, we still need to release some resources, or
we will leak them.
Fixes: afc7851fab ("serial: pxa: Fix out-of-bounds access through serial port index")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This chip has a diagnostics status bit informing about the state and
stability of the clock subsystem. According to the datasheet (STSint
register, bit 5, ClockReady), this bit works with the crystal
oscillator, but even without the PLL. Therefore:
- ensure that the clock check is done even when PLL is not active
- warn when the chip thinks that the clock is not ready yet
There are HW features which would let us wait asynchronously (there's a
maskable IRQ for that bit), but I think that even this simple check is a
net improvement. It would have saved me two days of debugging :).
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct to check the right rx dma cookie status in spit of it
works because only one cookie is running in the current sdma.
But it will not once sdma driver support multi cookies
running based on virt-dma.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially when register shadowing was introduced (commit 3a0ab62f43
("serial: imx: implement shadow registers for UCRx and UFCR")) the logic
to handle UCR2_SRST was wrong but documented consistently. Later the
handling was fixed, but the comment was not. This change makes up leeway
for the latter.
Fixes: 0aa821d846 ("serial: imx: fix cached UCR2 read on software reset")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=hB2y
-----END PGP SIGNATURE-----
Merge tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Help userspace log daemons to catch up with a flood of messages. They
will get woken after each message even if the console is far behind
and handled by another process.
- Flush printk safe buffers safely even when panic() happens in the
normal context.
- Fix possible va_list reuse when race happened in printk_safe().
- Remove %pCr printf format to prevent sleeping in the atomic context.
- Misc vsprintf code cleanup.
* tag 'printk-for-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
printk: drop in_nmi check from printk_safe_flush_on_panic()
lib/vsprintf: Remove atomic-unsafe support for %pCr
serial: sh-sci: Stop using printk format %pCr
thermal: bcm2835: Stop using printk format %pCr
clk: renesas: cpg-mssr: Stop using printk format %pCr
printk: fix possible reuse of va_list variable
printk: wake up klogd in vprintk_emit
vsprintf: Tweak pF/pf comment
lib/vsprintf: Mark expected switch fall-through
lib/vsprintf: Replace space with '_' before crng is ready
lib/vsprintf: Deduplicate pointer_string()
lib/vsprintf: Move pointer_string() upper
lib/vsprintf: Make flag_spec global
lib/vsprintf: Make strspec global
lib/vsprintf: Make dec_spec global
lib/test_printf: Mark big constant with UL
Here is the big tty/serial driver update for 4.18-rc1.
There's nothing major here, just lots of serial driver updates. Full
details are in the shortlog, nothing anything specific to call out here.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZzQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym2pQCggrWJsOeXLXgzhVDH6/qMFP9R/hEAoLTvmOWQ
BlPIlvRDm/ud33VogJ8t
=XS8u
-----END PGP SIGNATURE-----
Merge tag 'tty-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.18-rc1.
There's nothing major here, just lots of serial driver updates. Full
details are in the shortlog, nothing anything specific to call out
here.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (55 commits)
vt: Perform safe console erase only once
serial: imx: disable UCR4_OREN on shutdown
serial: imx: drop CTS/RTS handling from shutdown
tty: fix typo in ASYNCB_FOURPORT comment
serial: samsung: check DMA engine capabilities before using DMA mode
tty: Fix data race in tty_insert_flip_string_fixed_flag
tty: serial: msm_geni_serial: Fix TX infinite loop
serial: 8250_dw: Fix runtime PM handling
serial: 8250: omap: Fix idling of clocks for unused uarts
tty: serial: drop ATH79 specific SoC symbols
serial: 8250: Add missing rxtrig_bytes on Altera 16550 UART
serial/aspeed-vuart: fix a couple mod_timer() calls
serial: sh-sci: Use spin_{try}lock_irqsave instead of open coding version
serial: 8250_of: Add IO space support
tty/serial: atmel: use port->name as name in request_irq()
serial: imx: dma_unmap_sg buffers on shutdown
serial: imx: cleanup imx_uart_disable_dma()
tty: serial: qcom_geni_serial: Add early console support
tty: serial: qcom_geni_serial: Return IRQ_NONE for spurious interrupts
tty: serial: qcom_geni_serial: Use iowrite32_rep to write to FIFO
...
Printk format "%pCr" will be removed soon, as clk_get_rate() must not be
called in atomic context.
Replace it by open-coding the operation. This is safe here, as the code
runs in task context.
Link: http://lkml.kernel.org/r/1527845302-12159-4-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-doc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Petr Mladek <pmladek@suse.com>
UCR4_OREN is (depending on the configuration) enabled in startup,
but is never disabled. Fix this by disabling it in shutdown.
Reported-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to Documentation/serial/driver the shutdown function should
not disable RTS, so drop it.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA engine driver might not always provide all the features needed by
serial driver to properly operate in DMA mode, so check that before
selecting DMA mode.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Just set up the show callback in the tty_operations, and use
proc_create_single_data to create the file without additional
boilerplace code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
The GENI serial driver handled transmit by leaving stuff in the
common circular buffer until it had completely caught up to the head,
then clearing it out all at once. This is a suboptimal way to do
transmit, as it leaves data in the circular buffer that could be
freed. Moreover, the logic implementing it is wrong, and it is easy to
get into a situation where the UART infinitely writes out the same buffer.
I could reproduce infinite serial output of the same buffer by running
dmesg, then hitting Ctrl-C. I believe what happened is xmit_size was
something large, marching towards a larger value. Then the generic OS
code flushed out the buffer and replaced it with two characters. Now the
xmit_size is a large value marching towards a small value, which it wasn't
expecting. The driver subtracts xmit_size (very large) from
uart_circ_chars_pending (2), underflows, and repeats ad nauseum. The
locking isn't wrong here, as the locks are held whenever the buffer is
manipulated, it's just that the driver wasn't expecting the buffer to be
flushed out from underneath it in between transmits.
This change reworks transmit to grab what it can from the circular buffer,
and then update ->tail, both fixing the underflow and freeing up space
for a smoother circular experience.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using kgdb, you get an abort when accessing the UART registers.
This is because the driver has already entered runtime PM and so turned
off the bus clock needed to access the registers.
To fix this, set the capability indicating Runtime PM is active while idle.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that unused UARTs won't necessarily idle properly always
unless at least one byte tx transfer is done first.
After some debugging I narrowed down the problem to the scr register
dma configuration bits that need to be set before softreset for the
clocks to idle. Unless we do this, the module clkctrl idlest bits
may be set to 1 instead of 3 meaning the clock will never idle and
is blocking deeper idle states for the whole domain.
This might be related to the configuration done by the bootloader
or kexec booting where certain configurations cause the 8250 or
the clkctrl clock to jam in a way where setting of the scr bits
and reset is needed to clear it. I've tried diffing the 8250
registers for the various modes, but did not see anything specific.
So far I've only seen this on omap4 but I'm suspecting this might
also happen on the other clkctrl using SoCs considering they
already have a quirk enabled for UART_ERRATA_CLOCK_DISABLE.
Let's fix the issue by configuring scr before reset for basic dma
even if we don't use it. The scr register will be reset when we do
softreset few lines after, and we restore scr on resume. We should
do this for all the SoCs with UART_ERRATA_CLOCK_DISABLE quirk flag
set since the ones with UART_ERRATA_CLOCK_DISABLE are all based
using clkctrl similar to omap4.
Looks like both OMAP_UART_SCR_DMAMODE_1 | OMAP_UART_SCR_DMAMODE_CTL
bits are needed for the clkctrl to idle after a softreset.
And we need to add omap4 to also use the UART_ERRATA_CLOCK_DISABLE
for the related workaround to be enabled. This same compatible
value will also be used for omap5.
Fixes: cdb929e445 ("serial: 8250_omap: workaround errata around idling UART after using DMA")
Cc: Keerthy <j-keerthy@ti.com>
Cc: Matthijs van Duin <matthijsvanduin@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QCA MIPS support is being converted to pure OF. As part of this we are
dropping the SOC_AR* symbols. Additionally the SERIAL_AR933X style tty
is also found on a few SoCs newer that the AR933x.
This patch changes the dependency to ATH79, thus fixing the 2 issues
described above.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Altera 16550 UART core supports FCR Rx Trigger Level setting,
but the port definition in the driver is missing the rxtrig_bytes
array specifying the trigger levels. Add the array to make the Rx
Trigger Level setting available on this type of 16550 UART.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "unthrottle_timeout" is HZ/10 but mod_timer() takes a the actual
jiffie where you want it to timeout, not an offset.
Fixes: 5909c0bf9c ("serial/aspeed-vuart: Implement quick throttle mechanism")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jeremy Kerr <jk@ozlabs.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40f70c03e3 ("serial: sh-sci: add locking to console write
function to avoid SMP lockup") copied the strategy to avoid locking
problems in conjuncture with the console from the UART8250
driver. Instead using directly spin_{try}lock_irqsave(),
local_irq_save() followed by spin_{try}lock() was used. While this is
correct on mainline, for -rt it is a problem. spin_{try}lock() will
check if it is running in a valid context. Since the local_irq_save()
has already been executed, the context has changed and
spin_{try}lock() will complain. The reason why spin_{try}lock()
complains is that on -rt the spin locks are turned into mutexes and
therefore can sleep. Sleeping with interrupts disabled is not valid.
BUG: sleeping function called from invalid context at /home/wagi/work/rt/v4.4-cip-rt/kernel/locking/rtmutex.c:995
in_atomic(): 0, irqs_disabled(): 128, pid: 778, name: irq/76-eth0
CPU: 0 PID: 778 Comm: irq/76-eth0 Not tainted 4.4.126-test-cip22-rt14-00403-gcd03665c8318 #12
Hardware name: Generic RZ/G1 (Flattened Device Tree)
Backtrace:
[<c00140a0>] (dump_backtrace) from [<c001424c>] (show_stack+0x18/0x1c)
r7:c06b01f0 r6:60010193 r5:00000000 r4:c06b01f0
[<c0014234>] (show_stack) from [<c01d3c94>] (dump_stack+0x78/0x94)
[<c01d3c1c>] (dump_stack) from [<c004c134>] (___might_sleep+0x134/0x194)
r7:60010113 r6:c06d3559 r5:00000000 r4:ffffe000
[<c004c000>] (___might_sleep) from [<c04ded60>] (rt_spin_lock+0x20/0x74)
r5:c06f4d60 r4:c06f4d60
[<c04ded40>] (rt_spin_lock) from [<c02577e4>] (serial_console_write+0x100/0x118)
r5:c06f4d60 r4:c06f4d60
[<c02576e4>] (serial_console_write) from [<c0061060>] (call_console_drivers.constprop.15+0x10c/0x124)
r10:c06d2894 r9:c04e18b0 r8:00000028 r7:00000000 r6:c06d3559 r5:c06d2798
r4:c06b9914 r3:c02576e4
[<c0060f54>] (call_console_drivers.constprop.15) from [<c0062984>] (console_unlock+0x32c/0x430)
r10:c06d30d8 r9:00000028 r8:c06dd518 r7:00000005 r6:00000000 r5:c06d2798
r4:c06d2798 r3:00000028
[<c0062658>] (console_unlock) from [<c0062e1c>] (vprintk_emit+0x394/0x4f0)
r10:c06d2798 r9:c06d30ee r8:00000006 r7:00000005 r6:c06a78fc r5:00000027
r4:00000003
[<c0062a88>] (vprintk_emit) from [<c0062fa0>] (vprintk+0x28/0x30)
r10:c060bd46 r9:00001000 r8:c06b9a90 r7:c06b9a90 r6:c06b994c r5:c06b9a3c
r4:c0062fa8
[<c0062f78>] (vprintk) from [<c0062fb8>] (vprintk_default+0x10/0x14)
[<c0062fa8>] (vprintk_default) from [<c009cd30>] (printk+0x78/0x84)
[<c009ccbc>] (printk) from [<c025afdc>] (credit_entropy_bits+0x17c/0x2cc)
r3:00000001 r2:decade60 r1:c061a5ee r0:c061a523
r4:00000006
[<c025ae60>] (credit_entropy_bits) from [<c025bf74>] (add_interrupt_randomness+0x160/0x178)
r10:466e7196 r9:1f536000 r8:fffeef74 r7:00000000 r6:c06b9a60 r5:c06b9a3c
r4:dfbcf680
[<c025be14>] (add_interrupt_randomness) from [<c006536c>] (irq_thread+0x1e8/0x248)
r10:c006537c r9:c06cdf21 r8:c0064fcc r7:df791c24 r6:df791c00 r5:ffffe000
r4:df525180
[<c0065184>] (irq_thread) from [<c003fba4>] (kthread+0x108/0x11c)
r10:00000000 r9:00000000 r8:c0065184 r7:df791c00 r6:00000000 r5:df791d00
r4:decac000
[<c003fa9c>] (kthread) from [<c00101b8>] (ret_from_fork+0x14/0x3c)
r8:00000000 r7:00000000 r6:00000000 r5:c003fa9c r4:df791d00
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Daniel Wagner <daniel.wagner@siemens.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the 8250_of driver only supports MEM IO type
accesses.
Some development boards (Huawei D03, specifically) require
IO space access for 8250-compatible OF driver support, so
add it.
The modification is quite simple: just set the port iotype
and associated flags depending on the device address
resource type.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I was puzzled while looking at /proc/interrupts and random things showed
up between reboots. This occurred more often but I realised it later. The
"correct" output should be:
|38: 11861 atmel-aic5 2 Level ttyS0
but I saw sometimes
|38: 6426 atmel-aic5 2 Level tty1
and accounted it wrongly as correct. This is use after free and the
former example randomly got the "old" pointer which pointed to the same
content. With SLAB_FREELIST_RANDOM and HARDENED I even got
|38: 7067 atmel-aic5 2 Level E=Started User Manager for UID 0
or other nonsense.
As it turns out the tty, pointer that is accessed in atmel_startup(), is
freed() before atmel_shutdown(). It seems to happen quite often that the
tty for ttyS0 is allocated and freed while ->shutdown is not invoked. I
don't do anything special - just a systemd boot :)
Use dev_name(&pdev->dev) as the IRQ name for request_irq(). This exists
as long as the driver is loaded so no use-after-free here.
Cc: stable@vger.kernel.org
Fixes: 761ed4a945 ("tty: serial_core: convert uart_close to use tty_port_close")
Acked-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This properly unmaps DMA SG on device shutdown.
Reported-by: Nandor Han <nandor.han@ge.com>
Suggested-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unrelated CTSC/CTS disabling from imx_uart_disable_dma() and
move it to imx_uart_shutdown(), which is the only user of the DMA
disabling function. This should not change the driver's behaviour,
but improves readability. After this change imx_uart_disable_dma()
does the reverse thing of imx_uart_enable_dma().
Suggested-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the driver returns IRQ_HANDLED when spurious interrupts happen.
This is misleading. Fix the behavior by returning IRQ_NONE for spurious
interrupts.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use iowrite32_rep to write to the hardware FIFO so that the code does
not have to worry about the system endianness.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While initiating TX, only the register reads need to be ordered. The
register write order either is achieved due to data dependency or is
not required.
Use readl to achieve the read order and remove the unnecessary barrier.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Perform static initialization of console_port since its initial state has
no run-time dependencies.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use min3 helper to calculate the minimum value of 3 variables.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Document reason for newline character counting in console_write
* Document reason for disabling IRQ in the system resume operation
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The best granularity of residue that DMA engine can report is in the BURST
units, so the serial driver must use MAXBURST = 1 and DMA_SLAVE_BUSWIDTH_1_BYTE
if it relies on exact number of bytes transferred by DMA engine.
Fixes: 62c37eedb7 ("serial: samsung: add dma reqest/release functions")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As stated under "20) Conditional Compilation" in coding-style.rst. We
shall rather use __maybe_unused than preprocessor macros in such cases.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no reason to initialize uartclk to BASE_BAUD * 16 for DT based
systems.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Matt Redfearn <matt.redfearn@mips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9b96fbacda ("serial: PL011: clear pending interrupts")
clears the RX and receive timeout interrupts on pl011 startup, to
avoid a screaming-interrupt scenario that can occur when the
firmware or bootloader leaves these interrupts asserted.
This has been noted as an issue when running Linux on qemu [1].
Unfortunately, the above fix seems to lead to potential
misbehaviour if the RX FIFO interrupt is asserted _non_ spuriously
on driver startup, if the RX FIFO is also already full to the
trigger level.
Clearing the RX FIFO interrupt does not change the FIFO fill level.
In this scenario, because the interrupt is now clear and because
the FIFO is already full to the trigger level, no new assertion of
the RX FIFO interrupt can occur unless the FIFO is drained back
below the trigger level. This never occurs because the pl011
driver is waiting for an RX FIFO interrupt to tell it that there is
something to read, and does not read the FIFO at all until that
interrupt occurs.
Thus, simply clearing "spurious" interrupts on startup may be
misguided, since there is no way to be sure that the interrupts are
truly spurious, and things can go wrong if they are not.
This patch instead clears the interrupt condition by draining the
RX FIFO during UART startup, after clearing any potentially
spurious interrupt. This should ensure that an interrupt will
definitely be asserted if the RX FIFO subsequently becomes
sufficiently full.
The drain is done at the point of enabling interrupts only. This
means that it will occur any time the UART is newly opened through
the tty layer. It will not apply to polled-mode use of the UART by
kgdboc: since that scenario cannot use interrupts by design, this
should not matter. kgdboc will interact badly with "normal" use of
the UART in any case: this patch makes no attempt to paper over
such issues.
This patch does not attempt to address the case where the RX FIFO
fills faster than it can be drained: that is a pathological
hardware design problem that is beyond the scope of the driver to
work around. As a failsafe, the number of poll iterations for
draining the FIFO is limited to twice the FIFO size. This will
ensure that the kernel at least boots even if it is impossible to
drain the FIFO for some reason.
[1] [Qemu-devel] [Qemu-arm] [PATCH] pl011: do not put into fifo
before enabled the interruption
https://lists.gnu.org/archive/html/qemu-devel/2018-01/msg06446.html
Reported-by: Wei Xu <xuwei5@hisilicon.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Fixes: 9b96fbacda ("serial: PL011: clear pending interrupts")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Wei Xu <xuwei5@hisilicon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
c&p this function to probe as preparation for removing
cdns_uart_port[] static array.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver console functions are using pointer to static array with fixed
size. There can be only one serial console at the time which is found
by register_console(). register_console() is filling cons->index to
port->line value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
register_console() is called from
uart_add_one_port()->uart_configure_port()
that's why register_console() is called twice.
This patch remove console_initcall to call register_console() only from
one location.
Also based on my tests cdns_uart_console_setup() is not called
from the first register_console() call.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the clock is enabled, check if there is an error. Otherwise
clk_get_rate() can be called without enabled clock.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 0814e8d5da ("sc16is7xx: enable the clock")
Signed-off-by: Stefan Potyra <Stefan.Potyra@elektrobit.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
device->baud is always non zero value because it is checked already in
early_serial8250_setup() before init_port is called.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Baudrate calculation depends on requested baudrate and uart clock.
This patch is checking that uartclk is also passed.
The same logic is used 8250_early.c/init_port function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The platform_get_irq can return error. Assigning the return value to an
unsigned variable and checking it for negative value will always return
false.
Use an intermediate signed variable to get IRQ information, check for any
error and then assign it to 'irq' variable inside uart_port structure.
Signed-off-by: Karthikeyan Ramasubramanian <kramasub@codeaurora.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although we populate the ->throttle and ->unthrottle UART operations,
these may not be called until the ldisc has had a chance to schedule and
check buffer space. This means that we may overflow the flip buffers
without ever hitting the ldisc's throttle threshold.
This change implements an interrupt-based throttle, where we check for
space in the flip buffers before reading characters from the UART's
FIFO. If there's no space available, we disable the RX interrupt and
schedule a timer to check for space later.
For this, we need an unlocked version of the set_throttle function to be
able to change throttle state from the irq_handler, which already holds
port->lock.
This prevents a case where we drop characters under heavy RX load.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The aspeed VUART runs at LPC bus frequency, rather than being restricted
to a typical UART baud rate. This means that the VUART can receive a lot
of data, which can overrun tty flip buffers, and/or cause a large amount
of interrupt traffic.
This change implements the uart_port->throttle & unthrottle callbacks,
implemented by disabling the receiver line status & received data
available IRQs.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we export serial8250_rx_chars, which does a whole bunch of
reads from the 8250 data register, without any form of flow control
between reads.
An upcoming change to the aspeed vuart driver implements more
fine-grained flow control in the interrupt handler, requiring
character-at-a-time control over the rx path.
This change exports serial8250_read_char to allow this.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds a flag to indicate that a UART is has an external means
of synchronising its FIFO, without needing CTSRTS or XON/XOFF.
This allows us to use the throttle/unthrottle callbacks, without having
to claim other methods of flow control.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Tested-by: Eddie James <eajames@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DT based platforms when current-speed property is present baudrate
is setup. Also port->uartclk is initialized to bogus BASE_BAUD * 16
value. Drivers like uartps/ns16550 contain logic when baudrate and
uartclk is used for baudrate calculation.
The patch is reading optional clock-frequency property to replace bogus
BASE_BAUD * 16 calculation to have proper baudrate calculation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems IRQ lines between multiple UARTs might be shared. If so, the
irqflags have to be configured accordingly. The reason is: The 8250 port startup
code performs IRQ tests *before* the IRQ handler for that particular port is
registered. This is performed in serial8250_do_startup(). This function checks
whether IRQF_SHARED is configured and only then disables the IRQ line while
testing.
This test is performed upon each open() of the UART device. Imagine two UARTs
share the same IRQ line: On is already opened and the IRQ is active. When the
second UART is opened, the IRQ line has to be disabled while performing IRQ
tests. Otherwise an IRQ might handler might be invoked, but the the IRQ itself
cannot be handled, because the corresponding handler isn't registered,
yet. That's because the 8250 code uses a chain-handler and invokes the
corresponding port's IRQ handling rountines himself.
Unfortunately this IRQF_SHARED flag isn't configured for UARTs probed via device
tree even if the IRQs are shared. This way, the actual and shared IRQ line isn't
disabled while performing tests and the kernel correctly detects a spurious
IRQ. So, adding this flag to the DT probe solves the issue.
Note: The UPF_SHARE_IRQ flag is configured unconditionally. Therefore, the
IRQF_SHARED flag can be set unconditionally as well.
Example stacktrace by performing echo 1 > /dev/ttyS2 on a non-patched system:
|irq 85: nobody cared (try booting with the "irqpoll" option)
| [...]
|handlers:
|[<ffff0000080fc628>] irq_default_primary_handler threaded [<ffff00000855fbb8>] serial8250_interrupt
|Disabling IRQ #85
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable/Clear module level UART wakeup in UART_OMAP_WER register based on
return value of device_may_wakeup() in .suspend(). This allows
userspace to use sysfs to control the ability of UART to wakeup the
system from deep sleep state. Register is restored back in .startup()
call that happens as part of resume sequence.
With this patch, userspace can control UART wakeup capability via sysfs:
To enable wakeup capability:
echo enabled > /sys/class/tty/ttyXX/device/power/wakeup
For disabling wakeup capability:
echo disabled > /sys/class/tty/ttyXX/device/power/wakeup
Note that the UART wakeup events configured in the 8250 hardware only
work for idle modes that do not cut off power for the UART. For deeper
idle states, dedicated padconf wakeirqs must be used. Or in some cases
the UART RX pin can be remuxed to GPIO input if the GPIO block stays
powered.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous implementation has had a detrimental effect on devices using
high bitrates (bluetooth), as the fifo being non-empty for a single check
would result in a 10 µs delay.
Limit the change to devices with the new "marvell,armada-38x-uart"
compatible string. Also update the code to allow the first 1000 retries
to not perform a delay.
The maximum duration of retries has been increased to cover a worst-case
seen on the Armada 385 SoC. "dmesg ; resize", will fill the buffer with
text to output before doing a resize. At 9600 baud this took up to 13 ms
to flush all characters and avoid some getting lost.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HSCIF has facilities that allow moving the RX sampling point by between
-8 and 7 sampling cycles (one sampling cycles equals 1/15 of a bit
by default) to improve the error margin in case of slightly mismatched
bit rates between sender and receiver.
This patch tries to determine if shifting the sampling point can improve
the error margin and will enable it if so.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DT platforms, the sh-sci driver requires the presence of "serialN"
aliases in DT, from which instance IDs are derived. If a DT alias is
missing, the drivers fails to probe the corresponding serial port.
This becomes cumbersome when considering DT overlays, as currently
there is no upstream support for dynamically updating the /aliases node
in DT. Furthermore, even in the presence of such support, hardcoded
instance IDs in independent overlays are prone to conflicts.
Hence add support for dynamic instance IDs, to be used in the absence of
a DT alias. This makes serial ports behave similar to I2C and SPI
buses, which already support dynamic instances.
Ports in use are tracked using a simple bitmask of type unsigned long,
which is sufficient to handle all current hardware (max. 18 ports).
The maximum number of serial ports is still fixed, and configurable
through Kconfig. Range validation is done through both Kconfig and a
compile-time check.
Due to the fixed maximum number of serial ports, dynamic and static
instances share the same ID space. Static instances added later are
rejected when conflicting with dynamic instances registered earlier.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 99492c39f3 ("earlycon: Fix __earlycon_table stride") tried to fix
__earlycon_table stride by forcing the earlycon_id struct alignment to 32
and asking the linker to 32-byte align the __earlycon_table symbol. This
fix was based on commit 07fca0e57f ("tracing: Properly align linker
defined symbols") which tried a similar fix for the tracing subsystem.
However, this fix doesn't quite work because there is no guarantee that
gcc will place structures packed into an array format. In fact, gcc 4.9
chooses to 64-byte align these structs by inserting additional padding
between the entries because it has no clue that they are supposed to be in
an array. If we are unlucky, the linker will assign symbol
"__earlycon_table" to a 32-byte aligned address which does not correspond
to the 64-byte aligned contents of section "__earlycon_table".
To address this same problem, the fix to the tracing system was
subsequently re-implemented using a more robust table of pointers approach
by commits:
3d56e331b6 ("tracing: Replace syscall_meta_data struct array with pointer array")
6549864629 ("tracepoints: Fix section alignment using pointer array")
e4a9ea5ee7 ("tracing: Replace trace_event struct array with pointer array")
Let's use this same "array of pointers to structs" approach for
EARLYCON_TABLE.
Fixes: 99492c39f3 ("earlycon: Fix __earlycon_table stride")
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Suggested-by: Aaron Durbin <adurbin@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Simek