I've been seeing regular ASSERT failures in xfstests when running
fsstress based tests over the past month. xfs_getbmap() has been
failing this test:
XFS: Assertion failed: ((iflags & BMV_IF_DELALLOC) != 0) ||
(map[i].br_startblock != DELAYSTARTBLOCK), file: fs/xfs/xfs_bmap.c,
line: 5650
where it is encountering a delayed allocation extent after writing
all the dirty data to disk and then walking the extent map
atomically by holding the XFS_IOLOCK_SHARED to prevent new delayed
allocation extents from being created.
Test 083 on a 512 byte block size filesystem was used to reproduce
the problem, because it only had a 5s run timeand would usually fail
every 3-4 runs. This test is exercising ENOSPC behaviour by running
fsstress on a nearly full filesystem. The following trace extract
shows the final few events on the inode that tripped the assert:
xfs_ilock: flags ILOCK_EXCL caller xfs_setfilesize
xfs_setfilesize: isize 0x180000 disize 0x12d400 offset 0x17e200 count 7680
file size updated to 0x180000 by IO completion
xfs_ilock: flags ILOCK_EXCL caller xfs_iomap_write_delay
xfs_iext_insert: state idx 3 offset 3072 block 4503599627239432 count 1 flag 0 caller xfs_bmap_add_extent_hole_delay
xfs_get_blocks_alloc: size 0x180000 offset 0x180000 count 512 type startoff 0xc00 startblock -1 blockcount 0x1
xfs_ilock: flags ILOCK_EXCL caller __xfs_get_blocks
delalloc write, adding a single block at offset 0x180000
xfs_delalloc_enospc: isize 0x180000 disize 0x180000 offset 0x180200 count 512
ENOSPC trying to allocate a dellalloc block at offset 0x180200
xfs_ilock: flags ILOCK_EXCL caller xfs_iomap_write_delay
xfs_get_blocks_alloc: size 0x180000 offset 0x180200 count 512 type startoff 0xc00 startblock -1 blockcount 0x2
And succeeding on retry after flushing dirty inodes.
xfs_ilock: flags ILOCK_EXCL caller __xfs_get_blocks
xfs_delalloc_enospc: isize 0x180000 disize 0x180000 offset 0x180400 count 512
ENOSPC trying to allocate a dellalloc block at offset 0x180400
xfs_ilock: flags ILOCK_EXCL caller xfs_iomap_write_delay
xfs_delalloc_enospc: isize 0x180000 disize 0x180000 offset 0x180400 count 512
And failing the retry, giving a real ENOSPC error.
xfs_ilock: flags ILOCK_EXCL caller xfs_vm_write_failed
^^^^^^^^^^^^^^^^^^^
The smoking gun - the write being failed and cleaning up delalloc
blocks beyond EOF allocated by the failed write.
xfs_getattr:
xfs_ilock: flags IOLOCK_SHARED caller xfs_getbmap
xfs_ilock: flags ILOCK_SHARED caller xfs_ilock_map_shared
And that's where we died almost immediately afterwards.
xfs_bmapi_read() found delalloc extent beyond current file in memory
file size. Some debug I added to xfs_getbmap() showed the state just
before the assert failure:
ino 0x80e48: off 0xc00, fsb 0xffffffffffffffff, len 0x1, size 0x180000
start_fsb 0x106, end_fsb 0x638
ino flags 0x2 nex 0xd bmvcnt 0x555, len 0x3c58a6f23c0bf1, start 0xc00
ext 0: off 0x1fc, fsb 0x24782, len 0x254
ext 1: off 0x450, fsb 0x40851, len 0x30
ext 2: off 0x480, fsb 0xd99, len 0x1b8
ext 3: off 0x92f, fsb 0x4099a, len 0x3b
ext 4: off 0x96d, fsb 0x41844, len 0x98
ext 5: off 0xbf1, fsb 0x408ab, len 0xf
which shows that we found a single delalloc block beyond EOF (first
line of output) when we were returning the map for a length
somewhere around 10^16 bytes long (second line), and the on-disk
extents showed they didn't go past EOF (last lines).
Further debug added to xfs_vm_write_failed() showed this happened
when punching out delalloc blocks beyond the end of the file after
the failed write:
[ 132.606693] ino 0x80e48: vwf to 0x181000, sze 0x180000
[ 132.609573] start_fsb 0xc01, end_fsb 0xc08
It punched the range 0xc01 -> 0xc08, but the range we really need to
punch is 0xc00 -> 0xc07 (8 blocks from 0xc00) as this testing was
run on a 512 byte block size filesystem (8 blocks per page).
the punch from is 0xc00. So end_fsb is correct, but start_fsb is
wrong as we punch from start_fsb for (end_fsb - start_fsb) blocks.
Hence we are not punching the delalloc block beyond EOF in the case.
The fix is simple - it's a silly off-by-one mistake in calculating
the range. It's especially silly because the macro used to calculate
the start_fsb already takes into account the case where the inode
size is an exact multiple of the filesystem block size...
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
For the direct IO write path, we only really need the ilock to be taken in
exclusive mode during IO submission if we need to do extent allocation
instead of all the time.
Change the block mapping code to take the ilock in shared mode for the
initial block mapping, and only retake it exclusively when we actually
have to perform extent allocations. We were already dropping the ilock
for the transaction allocation, so this doesn't introduce new race windows.
Based on an earlier patch from Dave Chinner.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Instead of calling xfs_zero_eof with the ilock held only take it internally
for the minimall required critical section around xfs_bmapi_read. This
also requires changing the calling convention for xfs_zero_last_block
slightly. The actual zeroing operation is still serialized by the iolock,
which must be taken exclusively over the call to xfs_zero_eof.
We could in fact use a shared lock for the xfs_bmapi_read calls as long as
the extent list has been read in, but given that we already hold the iolock
exclusively there is little reason to micro optimize this further.
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
We do not need the ilock for most checks done in the beginning of
xfs_setattr_size. Replace the long critical section before starting the
transaction with a smaller one around xfs_zero_eof and an optional one
inside xfs_qm_dqattach that isn't entered unless using quotas. While
this isn't a big optimization for xfs_setattr_size itself it will allow
pushing the ilock into xfs_zero_eof itself later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
We do not need the ilock for generic_write_checks and the i_size_read,
which are protected by i_mutex and/or iolock, so reduce the ilock
critical section to just the call to xfs_zero_eof.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Check if we actually need to attach a dquot before taking the ilock in
xfs_qm_dqattach. This avoid superflous lock roundtrips for the common cases
of quota support compiled in but not activated on a filesystem and an
inode that already has the dquots attached.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Because the mount process can run a quotacheck and consume lots of
inodes, we need to be able to run periodic inode reclaim during the
mount process. This will prevent running the system out of memory
during quota checks.
This essentially reverts 2bcf6e97, but that is safe to do now that
the quota sync code that was causing problems during long quotacheck
executions is now gone.
The reclaim work is currently protected from running during the
unmount process by a check against MS_ACTIVE. Unfortunately, this
also means that the reclaim work cannot run during mount. The
unmount process should stop the reclaim cleanly before freeing
anything that the reclaim work depends on, so there is no need to
have this guard in place.
Also, the inode reclaim work is demand driven, so there is no need
to start it immediately during mount. It will be started the moment
an inode is queued for reclaim, so qutoacheck will trigger it just
fine.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Mark Tinguely <tinguely@sgi.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
Check if the project quota is running or not before performing
xfs_qm_statvfs(), just return if not. Otherwise the ASSERT
XFS_IS_QUOTA_RUNNING in xfs_qm_dqget will be popped.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Signed-off-by: Ben Myers <bpm@sgi.com>
I have a new optimized x86 "strncpy_from_user()" that will use these
same helper functions for all the same reasons the name lookup code uses
them. This is preparation for that.
This moves them into an architecture-specific header file. It's
architecture-specific for two reasons:
- some of the functions are likely to want architecture-specific
implementations. Even if the current code happens to be "generic" in
the sense that it should work on any little-endian machine, it's
likely that the "multiply by a big constant and shift" implementation
is less than optimal for an architecture that has a guaranteed fast
bit count instruction, for example.
- I expect that if architectures like sparc want to start playing
around with this, we'll need to abstract out a few more details (in
particular the actual unaligned accesses). So we're likely to have
more architecture-specific stuff if non-x86 architectures start using
this.
(and if it turns out that non-x86 architectures don't start using
this, then having it in an architecture-specific header is still the
right thing to do, of course)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
1) Fix inaccuracies in network driver interface documentation, from Ben
Hutchings.
2) Fix handling of negative offsets in BPF JITs, from Jan Seiffert.
3) Compile warning, locking, and refcounting fixes in netfilter's
xt_CT, from Pablo Neira Ayuso.
4) phonet sendmsg needs to validate user length just like any other
datagram protocol, fix from Sasha Levin.
5) Ipv6 multicast code uses wrong loop index, from RongQing Li.
6) Link handling and firmware fixes in bnx2x driver from Yaniv Rosner
and Yuval Mintz.
7) mlx4 erroneously allocates 4 pages at a time, regardless of page
size, fix from Thadeu Lima de Souza Cascardo.
8) SCTP socket option wasn't extended in a backwards compatible way,
fix from Thomas Graf.
9) Add missing address change event emissions to bonding, from Shlomo
Pongratz.
10) /proc/net/dev regressed because it uses a private offset to track
where we are in the hash table, but this doesn't track the offset
pullback that the seq_file code does resulting in some entries being
missed in large dumps.
Fix from Eric Dumazet.
11) do_tcp_sendpage() unloads the send queue way too fast, because it
invokes tcp_push() when it shouldn't. Let the natural sequence
generated by the splice paths, and the assosciated MSG_MORE
settings, guide the tcp_push() calls.
Otherwise what goes out of TCP is spaghetti and doesn't batch
effectively into GSO/TSO clusters.
From Eric Dumazet.
12) Once we put a SKB into either the netlink receiver's queue or a
socket error queue, it can be consumed and freed up, therefore we
cannot touch it after queueing it like that.
Fixes from Eric Dumazet.
13) PPP has this annoying behavior in that for every transmit call it
immediately stops the TX queue, then calls down into the next layer
to transmit the PPP frame.
But if that next layer can take it immediately, it just un-stops the
TX queue right before returning from the transmit method.
Besides being useless work, it makes several facilities unusable, in
particular things like the equalizers. Well behaved devices should
only stop the TX queue when they really are full, and in PPP's case
when it gets backlogged to the downstream device.
David Woodhouse therefore fixed PPP to not stop the TX queue until
it's downstream can't take data any more.
14) IFF_UNICAST_FLT got accidently lost in some recent stmmac driver
changes, re-add. From Marc Kleine-Budde.
15) Fix link flaps in ixgbe, from Eric W. Multanen.
16) Descriptor writeback fixes in e1000e from Matthew Vick.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
net: fix a race in sock_queue_err_skb()
netlink: fix races after skb queueing
doc, net: Update ndo_start_xmit return type and values
doc, net: Remove instruction to set net_device::trans_start
doc, net: Update netdev operation names
doc, net: Update documentation of synchronisation for TX multiqueue
doc, net: Remove obsolete reference to dev->poll
ethtool: Remove exception to the requirement of holding RTNL lock
MAINTAINERS: update for Marvell Ethernet drivers
bonding: properly unset current_arp_slave on slave link up
phonet: Check input from user before allocating
tcp: tcp_sendpages() should call tcp_push() once
ipv6: fix array index in ip6_mc_add_src()
mlx4: allocate just enough pages instead of always 4 pages
stmmac: re-add IFF_UNICAST_FLT for dwmac1000
bnx2x: Clear MDC/MDIO warning message
bnx2x: Fix BCM57711+BCM84823 link issue
bnx2x: Clear BCM84833 LED after fan failure
bnx2x: Fix BCM84833 PHY FW version presentation
bnx2x: Fix link issue for BCM8727 boards.
...
commit 2f53384424 (tcp: allow splice() to build full TSO packets) added
a regression for splice() calls using SPLICE_F_MORE.
We need to call tcp_flush() at the end of the last page processed in
tcp_sendpages(), or else transmits can be deferred and future sends
stall.
Add a new internal flag, MSG_SENDPAGE_NOTLAST, acting like MSG_MORE, but
with different semantic.
For all sendpage() providers, its a transparent change. Only
sock_sendpage() and tcp_sendpages() can differentiate the two different
flags provided by pipe_to_sendpage()
Reported-by: Tom Herbert <therbert@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: H.K. Jerry Chu <hkchu@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail>com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
debugfs and a few other drivers use an open-coded version of
simple_open() to pass a pointer from the file to the read/write file
ops. Add support for this simple case to libfs so that we can remove
the many duplicate copies of this simple function.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It was introduced by d1d5e05ffd ("hugetlbfs: return error code when
initializing module") but as Al pointed out, is a bad idea.
Quoted comments from Al:
"Note that unregister_filesystem() in module init is *always* wrong;
it's not an issue here (it's done too early to care about and
realistically the box is not going anywhere - it'll panic when attempt
to exec /sbin/init fails, if not earlier), but it's a damn bad
example.
Consider a normal fs module. Somebody loads it and in parallel with
that we get a mount attempt on that fs type. It comes between
register and failure exits that causes unregister; at that point we
are screwed since grabbing a reference to module as done by mount is
enough to prevent exit, but not to prevent the failure of init. As
the result, module will get freed when init fails, mounted fs of that
type be damned."
So remove it.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allocation can be as large as 64k.
- Add __GFP_NOWARN so the a falied kmalloc() is silent
- Fall back to vmalloc() if the kmalloc() failed
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: David Rientjes <rientjes@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allocation can be as large as 64k. As David points out, "falling
back to vmalloc here is much better solution than failing to retreive
the attribute - it will work no matter how fragmented memory gets. That
means we don't get incomplete backups occurring after days or months of
uptime and successful backups".
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: David Rientjes <rientjes@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This size is user controllable, up to a maximum of XATTR_LIST_MAX (64k).
So it's trivial for someone to trigger a stream of order:4 page
allocation errors.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Chinner <david@fromorbit.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The proc_parse_options() call from proc_mount() runs only once at boot
time. So on any later mount attempt, any mount options are ignored
because ->s_root is already initialized.
As a consequence, "mount -o <options>" will ignore the options. The
only way to change mount options is "mount -o remount,<options>".
To fix this, parse the mount options unconditionally.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Reported-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Tested-by: Arkadiusz Miskiewicz <a.miskiewicz@gmail.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull CIFS fixes from Steve French.
* git://git.samba.org/sfrench/cifs-2.6:
Fix UNC parsing on mount
Remove unnecessary check for NULL in password parser
CIFS: Fix VFS lock usage for oplocked files
Revert "CIFS: Fix VFS lock usage for oplocked files"
cifs: writing past end of struct in cifs_convert_address()
cifs: silence compiler warnings showing up with gcc-4.7.0
CIFS: Fix VFS lock usage for oplocked files
The code cleanup of cifs_parse_mount_options resulted in a new bug being
introduced in the parsing of the UNC. This results in vol->UNC being
modified before vol->UNC was allocated.
Reported-by: Steve French <smfrench@gmail.com>
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
The password parser has an unnecessary check for a NULL value which
triggers warnings in source checking tools. The code contains artifacts
from the old parsing code which are no longer required.
Signed-off-by: Sachin Prabhu <sprabhu@redhat.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We can deadlock if we have a write oplock and two processes
use the same file handle. In this case the first process can't
unlock its lock if the second process blocked on the lock in the
same time.
Fix it by using posix_lock_file rather than posix_lock_file_wait
under cinode->lock_mutex. If we request a blocking lock and
posix_lock_file indicates that there is another lock that prevents
us, wait untill that lock is released and restart our call.
Cc: stable@kernel.org
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Signed-off-by: Steve French <sfrench@us.ibm.com>
"s6->sin6_scope_id" is an int bits but strict_strtoul() writes a long
so this can corrupt memory on 64 bit systems.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
gcc-4.7.0 has started throwing these warnings when building cifs.ko.
CC [M] fs/cifs/cifssmb.o
fs/cifs/cifssmb.c: In function ‘CIFSSMBSetCIFSACL’:
fs/cifs/cifssmb.c:3905:9: warning: array subscript is above array bounds [-Warray-bounds]
fs/cifs/cifssmb.c: In function ‘CIFSSMBSetFileInfo’:
fs/cifs/cifssmb.c:5711:8: warning: array subscript is above array bounds [-Warray-bounds]
fs/cifs/cifssmb.c: In function ‘CIFSSMBUnixSetFileInfo’:
fs/cifs/cifssmb.c:6001:25: warning: array subscript is above array bounds [-Warray-bounds]
This patch cleans up the code a bit by using the offsetof macro instead
of the funky "&pSMB->hdr.Protocol" construct.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
We can deadlock if we have a write oplock and two processes
use the same file handle. In this case the first process can't
unlock its lock if another process blocked on the lock in the
same time.
Fix this by removing lock_mutex protection from waiting on a
blocked lock and protect only posix_lock_file call.
Cc: stable@kernel.org
Signed-off-by: Pavel Shilovsky <piastry@etersoft.ru>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Pull second try at vfs part d#2 from Al Viro:
"Miklos' first series (with do_lookup() rewrite split into edible
chunks) + assorted bits and pieces.
The 'untangling of do_lookup()' series is is a splitup of what used to
be a monolithic patch from Miklos, so this series is basically "how do
I convince myself that his patch is correct (or find a hole in it)".
No holes found and I like the resulting cleanup, so in it went..."
Changes from try 1: Fix a boot problem with selinux, and commit messages
prettied up a bit.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (24 commits)
vfs: fix out-of-date dentry_unhash() comment
vfs: split __lookup_hash
untangling do_lookup() - take __lookup_hash()-calling case out of line.
untangling do_lookup() - switch to calling __lookup_hash()
untangling do_lookup() - merge d_alloc_and_lookup() callers
untangling do_lookup() - merge failure exits in !dentry case
untangling do_lookup() - massage !dentry case towards __lookup_hash()
untangling do_lookup() - get rid of need_reval in !dentry case
untangling do_lookup() - eliminate a loop.
untangling do_lookup() - expand the area under ->i_mutex
untangling do_lookup() - isolate !dentry stuff from the rest of it.
vfs: move MAY_EXEC check from __lookup_hash()
vfs: don't revalidate just looked up dentry
vfs: fix d_need_lookup/d_revalidate order in do_lookup
ext3: move headers to fs/ext3/
migrate ext2_fs.h guts to fs/ext2/ext2.h
new helper: ext2_image_size()
get rid of pointless includes of ext2_fs.h
ext2: No longer export ext2_fs.h to user space
mtdchar: kill persistently held vfsmount
...
64252c75a2 "vfs: remove dget() from
dentry_unhash()" changed the implementation but not the comment.
Cc: Sage Weil <sage@newdream.net>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Split __lookup_hash into two component functions:
lookup_dcache - tries cached lookup, returns whether real lookup is needed
lookup_real - calls i_op->lookup
This eliminates code duplication between d_alloc_and_lookup() and
d_inode_lookup().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Everything arriving into if (!dentry) will have need_reval = 1.
Indeed, the only way to get there with need_reval reset to 0 would
be via
if (unlikely(d_need_lookup(dentry)))
goto unlazy;
if (unlikely(dentry->d_flags & DCACHE_OP_REVALIDATE)) {
status = d_revalidate(dentry, nd);
if (unlikely(status <= 0)) {
if (status != -ECHILD)
need_reval = 0;
goto unlazy;
...
unlazy:
/* no assignments to dentry */
if (dentry && unlikely(d_need_lookup(dentry))) {
dput(dentry);
dentry = NULL;
}
and if d_need_lookup() had already been false the first time around, it
will remain false on the second call as well.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
d_lookup() *will* fail after successful d_invalidate(), if we are
holding i_mutex all along. IOW, we don't need to jump back to
l: - we know what path will be taken there and can do that (i.e.
d_alloc_and_lookup()) directly.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Duplicate the revalidation-related parts into if (!dentry) branch.
Next step will be to pull them under i_mutex.
This and the next 8 commits are more or less a splitup of patch
by Miklos; folks, when you are working with something that convoluted,
carve your patches up into easily reviewed steps, especially when
a lot of codepaths involved are rarely hit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The only caller of __lookup_hash() that needs the exec permission check on
parent is lookup_one_len().
All lookup_hash() callers already checked permission in LOOKUP_PARENT walk.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
__lookup_hash() calls ->lookup() if the dentry needs lookup and on success
revalidates the dentry (all under dir->i_mutex).
While this is harmless it doesn't make a lot of sense.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Doing revalidate on a dentry which has not yet been looked up makes no sense.
Move the d_need_lookup() check before d_revalidate().
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
1. TRACE_EVENT(sched_process_exec) forgets to actually use the
old pid argument, it sets ->old_pid = p->pid.
2. search_binary_handler() uses the wrong pid number. tracepoint
needs the global pid_t from the root namespace, while old_pid
is the virtual pid number as it seen by the tracer/parent.
With this patch we have two pid_t's in search_binary_handler(),
not really nice. Perhaps we should switch to "struct pid*", but
in this case it would be better to cleanup the current code
first and move the "depth == 0" code outside.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: David Smith <dsmith@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Link: http://lkml.kernel.org/r/20120330162636.GA4857@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Chinner