It turns out that the Windows GPIO driver for Sunrisepoint PCH-H uses
similar bank structure than it does for Cannon Lake with the exception
that here the bank size is always 24 pins. Starting from pad group E the
BIOS/Windows GPIO numbering does not match the hardware anymore but
instead there are gaps to make each pad group ("bank") consume exactly
24 pins. Because of this Linux does not use correct pins for
GpioIo/GpioIo resources exposed by the BIOS.
This patch aligns the GPIO number space with BIOS/Windows to make sure
the same numbering scheme is used in Linux as well following what we did
already for Intel Cannon Lake.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1543769
Reported-by: Vivien FRASCA <vivien.frasca@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When we dropped the custom Linux GPIO translation it resulted that the
IRQ numbers changed slightly as well. Normally this would be fine
because everyone is expected to use controller relative GPIO numbers and
ACPI GpioIo/GpioInt resources. However, there is a certain set of
Intel_Strago based Chromebooks where i8042 keyboard controller IRQ
number is hardcoded be 182 (this is corrected with newer coreboot but
the older ones still have the hardcoded Linux IRQ number). Because of
this hardcoded IRQ number keyboard on those systems accidentally broke
again.
Fix this by iteratively associating IRQ descriptors to the chip irqdomain
so that there are no gaps on those systems. Other systems are not
affected.
Fixes: 03c4749dd6 ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199463
Reported-by: Sultan Alsawaf <sultanxda@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO bank is range from GPIOAO_0 to GPIOAO_13.
Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Reported-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of
depending on it. This is merged with the same pattern
for all the ISA drivers and some other Kconfig cleanups
related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of
this SoC from the ARM tree.
- Move the documentation over to driver-api to conform with
the rest of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h>
that we want to get rid of.
- Managed to remove VLA allocation from two drivers pending
more fixes in this area for the next merge window.
- Misc janitorial fixes.
-----BEGIN PGP SIGNATURE-----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=C5t5
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.17 kernel cycle:
New drivers:
- Nintendo Wii GameCube GPIO, known as "Hollywood"
- Raspberry Pi mailbox service GPIO expander
- Spreadtrum main SC9860 SoC and IEC GPIO controllers.
Improvements:
- Implemented .get_multiple() callback for most of the
high-performance industrial GPIO cards for the ISA bus.
- ISA GPIO drivers now select the ISA_BUS_API instead of depending on
it. This is merged with the same pattern for all the ISA drivers
and some other Kconfig cleanups related to this.
Cleanup:
- Delete the TZ1090 GPIO drivers following the deletion of this SoC
from the ARM tree.
- Move the documentation over to driver-api to conform with the rest
of the kernel documentation build.
- Continue to make the GPIO drivers include only
<linux/gpio/driver.h> and not the too broad <linux/gpio.h> that we
want to get rid of.
- Managed to remove VLA allocation from two drivers pending more
fixes in this area for the next merge window.
- Misc janitorial fixes"
* tag 'gpio-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: Add Spreadtrum PMIC EIC driver support
gpio: Add Spreadtrum EIC driver support
dt-bindings: gpio: Add Spreadtrum EIC controller documentation
gpio: ath79: Fix potential NULL dereference in ath79_gpio_probe()
pinctrl: qcom: Don't allow protected pins to be requested
gpiolib: Support 'gpio-reserved-ranges' property
gpiolib: Change bitmap allocation to kmalloc_array
gpiolib: Extract mask allocation into subroutine
dt-bindings: gpio: Add a gpio-reserved-ranges property
gpio: mockup: fix a potential crash when creating debugfs entries
gpio: pca953x: add compatibility for pcal6524 and pcal9555a
gpio: dwapb: Add support for a bus clock
gpio: Remove VLA from xra1403 driver
gpio: Remove VLA from MAX3191X driver
gpio: ws16c48: Implement get_multiple callback
gpio: gpio-mm: Implement get_multiple callback
gpio: 104-idi-48: Implement get_multiple callback
gpio: 104-dio-48e: Implement get_multiple callback
gpio: pcie-idio-24: Implement get_multiple/set_multiple callbacks
gpio: pci-idio-16: Implement get_multiple callback
...
New drivers:
- Qualcomm SDM845: this is their new flagship SoC platform
which seems to be targeted at premium mobile handsets.
- Renesas R-Car M3-N SoC.
- Renesas R8A77980 SoC.
- NXP (ex Freescale) i.MX 6SLL SoC.
- Mediatek MT2712 SoC.
- Allwinner H6 SoC.
Improvements:
- Uniphier adds a few new functions and pins.
- Renesas refactorings and additional pin definitions.
- Improved pin groups for Axis Artpec6.
Cleanup:
- Drop the TZ1090 drivers. This platform is no longer
maintained and is being deleted.
- Drop ST-Ericsson U8540/U9540 support as this was never
productified.
- Overall minor fixes and janitorial.
-----BEGIN PGP SIGNATURE-----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=IT6S
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control bulk updates from Linus Walleij:
"New drivers:
- Qualcomm SDM845: this is their new flagship SoC platform which
seems to be targeted at premium mobile handsets.
- Renesas R-Car M3-N SoC.
- Renesas R8A77980 SoC.
- NXP (ex Freescale) i.MX 6SLL SoC.
- Mediatek MT2712 SoC.
- Allwinner H6 SoC.
Improvements:
- Uniphier adds a few new functions and pins.
- Renesas refactorings and additional pin definitions.
- Improved pin groups for Axis Artpec6.
Cleanup:
- Drop the TZ1090 drivers. This platform is no longer maintained and
is being deleted.
- Drop ST-Ericsson U8540/U9540 support as this was never
productified.
- Overall minor fixes and janitorial"
* tag 'pinctrl-v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (82 commits)
pinctrl: uniphier: add UART hardware flow control pin-mux settings
pinctrl: sunxi: add support for the Allwinner H6 main pin controller
pinctrl: sunxi: change irq_bank_base to irq_bank_map
pinctrl: sunxi: introduce IRQ bank conversion function
pinctrl: sunxi: refactor irq related register function to have desc
pinctrl: msm8998: Remove owner assignment from platform_driver
pinctrl: uniphier: divide I2S and S/PDIF audio out pin-mux group
pinctrl: uniphier: add PXs2 Audio in/out pin-mux settings
pinctrl/amd: poll InterruptEnable bits in enable_irq
pinctrl: ocelot: fix gpio direction
pinctrl: mtk: fix check warnings.
pintcrl: mtk: support bias-disable of generic and special pins simultaneously
pinctrl: add mt2712 pinctrl driver
pinctrl: pinctrl-single: Fix pcs_request_gpio() when bits_per_mux != 0
pinctrl: imx: Add pinctrl driver support for imx6sll
dt-bindings: imx: update pinctrl doc for imx6sll
pinctrl: intel: Implement intel_gpio_get_direction callback
pinctrl: stm32: add 'depends on HAS_IOMEM' to fix unmet dependency
pinctrl: mediatek: mtk-common: use true and false for boolean values
pinctrl: sunxi: always look for apb block
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
Some qcom platforms make some GPIOs or pins unavailable for use
by non-secure operating systems, and thus reading or writing the
registers for those pins will cause access control issues and
reset the device. With a DT/ACPI property to describe the set of
pins that are available for use, parse the available pins and set
the irq valid bits for gpiolib to know what to consider 'valid'.
This should avoid any issues with gpiolib. Furthermore, implement
the pinmux_ops::request function so that pinmux can also make
sure to not use pins that are unavailable.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
UniPhier SoCs have the following pins for hardware flow control of UART:
XRTS, XCTS
and for modem control of UART:
XDTR, XDSR, XDCD, XRI
The port number with the flow control is SoC-dependent.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner H6 SoC has two pin controllers, one main controller
(called CPUX-PORT in user manual) and one controller in CPUs power
domain (called CPUS-PORT in user manual).
This commit introduces support for the main pin controller on H6.
The pin bank A and B are not wired out and hidden from the SoC's
documents, however it's shown that the "ATE" (an AC200 chip
co-packaged with the H6 die) is connected to the main SoC die via these
pin banks. The information about these banks is just copied from the BSP
pinctrl driver, but re-formatted to fit the mainline pinctrl driver
format. The GPIO functions are dropped, as they're impossible to use --
except a GPIO&IRQ only pin (PB20) which might be the IRQ of ATE.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5.
Change the current code that uses IRQ bank base to a IRQ bank map, in
order to support the case that holes exist among IRQ banks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5. Some
refactors in the sunxi pinctrl framework are needed.
This commit introduces a IRQ bank conversion function, which replaces
the "(bank_base + bank)" code in IRQ register access.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the new H6 SoC has holes in the IRQ registers, refactor the IRQ
related register function for getting the full pinctrl desc structure.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The blackfin architecture is getting removed, so these are
now obsolete.
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In certain cases interrupt enablement will be delayed relative to when
the InterruptEnable bits are written. One example of this is when
a GPIO's "debounce" logice is first enabled. After enabling debounce,
there is a 900 us "warm up" period during which InterruptEnable[0]
(bit 11) will read as 0 despite being written 1. During this time
InterruptSts will not be updated, nor will interrupts be delivered, even
if the GPIO's interrupt configuration has been written to the register.
To work around this delay, poll the InterruptEnable bits after setting
them to ensure interrupts have truly been enabled in hardware before
returning from the irq_enable handler.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bits have to be cleared in DEVCPU_GCB:GPIO:GPIO_OE for input and set for
output. ocelot_gpio_set_direction() got it wrong and this went unnoticed
when the driver was reworked.
Reported-by: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For generic pins, parameter "arg" is 0 or 1.
For special pins, bias-disable is set by R0R1,
so we need transmited "00" to set bias-disable
When we set "bias-disable" as high-z property,
the parameter should be "MTK_PUPD_SET_R1R0_00".
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit includes mt2712 pinctrl driver.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Reviewed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes pcs_request_gpio() in the pinctrl-single driver when
bits_per_mux != 0. It appears this was overlooked when the multiple
pins per register feature was added.
Fixes: 4e7e8017a8 ("pinctrl: pinctrl-single: enhance to configure multiple pins of different modules")
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allows querying GPIO direction from the pad config register.
If the pad is not in GPIO mode, return an error.
Signed-off-by: Javier Arteaga <javier@emutex.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These configs select MFD_SYSCON, but do not depend on HAS_IOMEM.
Compile testing on architecture without HAS_IOMEM causes "unmet
direct dependencies" in Kconfig phase.
Detected by "make ARCH=score allyesconfig".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Assign true or false to boolean variables instead of an integer value.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Allwinner pinctrl device tree binding suggests that a clock named
"apb" would drive the pin controller IP. However (for legacy reasons) we
rely on this clock actually being the first clock defined.
Since named clocks can be in any order, let's explicitly check for a
clock called "apb" if there is more than one clock referenced.
Kudo to Maxime for suggesting this much more elegant approach.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add USB pin groups on R-Car M3-N,
- Add support for the new R-Car V3H SoC,
- Add EtherAVB pin groups on R-Car V3M,
- Miscellaneous fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=swQl
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.17 (take two)
- Add USB pin groups on R-Car M3-N,
- Add support for the new R-Car V3H SoC,
- Add EtherAVB pin groups on R-Car V3M,
- Miscellaneous fixes and cleanups.
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use union vin_data and VIN_DATA_PIN_GROUP() to reduce redundancies
in pin definitions.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: fbd452aeb4 ("pinctrl: sh-pfc: r8a77995: Add VIN4 pins, groups and function")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: 8db6cbabac ("pinctrl: sh-pfc: r8a7796: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
RGB666 has a pin assignment that differs from the other formats.
Fixes: 6b4de40810 ("pinctrl: sh-pfc: r8a7795: Add VIN4, VIN5 pins, groups and functions")
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 66abd968d0 ("pinctrl: sh-pfc: r8a77995: Add EthernetAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: fa3e8b71b9 ("pinctrl: sh-pfc: r8a77965: Add EtherAVB groups/functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 41397032c4 ("pinctrl: sh-pfc: r8a7796: Add group for AVB MDIO and MII pins")
Fixes: 9c99a63ec7 ("pinctrl: sh-pfc: r8a7796: Add EtherAVB pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: b25719eb93 ("pinctrl: sh-pfc: r8a7795: Add group for AVB MDIO and MII pins")
Fixes: 819fd4bfcc ("pinctrl: sh-pfc: r8a7795: add EtherAVB support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
On other Renesas SoCs, the pin group for the MDIO bus is named "mdio"
instead of "mdc". Fix the inconsistency, while retaining backwards
compatibility with old DTBs using a pin group alias.
Fixes: 30c078de6f ("pinctrl: sh-pfc: r8a7795: Add EtherAVB pins, groups and function")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Add a macro to refer to another pin group with a different name.
This will be used to rename wrongly-named pin groups, while retaining
backwards compatibility with old DTBs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
The pin controller drivers for all R-Car Gen2 SoCs have entries for the
EtherAVB TX_ER pins in their EtherAVB MII groups, except on R-Car H2.
Add the missing pin to restore consistency.
Note that technically TX_ER is an optional signal in the MII bus, and
thus could have its own group, but this is currently not supported by
any R-Car Gen2 pin controller driver.
Fixes: 19ef697d1e ("sh-pfc: r8a7790: add EtherAVB pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB pin groups to the R8A77970 PFC driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the PFC support for the R8A77980 SoC including pin groups for some
on-chip devices such as AVB, CAN-FD, GETHER, [H]SCIF, I2C, INTC-EX, MMC,
MSIOF, PWM, and VIN...
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
They follow the style of the existing PORT_GP_CFG_<n>() macros and
will be used by a follow-up patch for the R8A77980 SoC.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Driver uses alias from Device Tree as an index of pin controller data
array. In case of a wrong DTB or an out-of-tree DTB, the alias could be
outside of this data array leading to out-of-bounds access.
Depending on binary and memory layout, this could be handled properly
(showing error like "samsung-pinctrl 3860000.pinctrl: driver data not
available") or could lead to exceptions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <stable@vger.kernel.org>
Fixes: 30574f0db1 ("pinctrl: add samsung pinctrl and gpiolib driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds USB30 (USB3.0 host) pin, group and function to
the R8A77965 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Add DU and VIN pin groups on R-Car D3,
- Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
- Add support for the new R-Car M3-N SoC,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJamSLtAAoJEEgEtLw/Ve77Qb0QAIaVFrBq4OAfQGTU5wYrJvl2
OMNjt7oPf4LHxqlo979peJ3nxfMZxMCZ1MCIzHEF1hKaOb+PJMrWILt71UJwNnUY
TSAgtZUtl6LUxl2F/ZJ7DiqUTKog8m/jfYwgbdva+FlSNd3pWUYCNFX00SGDtonR
E/hrx4XYFM+EBuIVrccw/U1u1Cx6FjSEbG7QjBLXlu8ZxBAvHI3V8lyOv0p1jzBt
hqNQHsa6O/D2NDypTUCL8Bqe+otZvfnJwQvrNWF7pZBF3m/vaWOROBecZ/QajpPf
RftyFEVvtoyeViG7cD0P6h7G0I8kEbzNFODIfLYXjgsNJt88BtotyRTZI/vRG5Ob
BSFfkAe4JkRux/7Ry6y/ptMJSZUJcjXo3w8xFXj/DqpA6A+1EyKCypGil6eiGH9q
5kJHpYVDtoQSINWKmOTlu1MQXOo1P+IpYJDgYDOLOHxurRyRQWVW8htRe8zh8WTu
4ikvP8s0kAv7MupISsNUTnwuVD2IdJyaKoMDh6stZOKu0cWzV/+tUOefEZ0xx0HF
OeYll9iNrJh0OmIj+wyN770BbaR2q8Gq6W26dxJRAhupGVJw/PrmzDMdqb2FTASp
20Xrjo2ppIZ4AlWgN8Mx5ZPIaVhLS5pmZ2O1CrFQI34a8ZjO3GA72Jx8dUYNh1lS
7Kyn6eCXLbkVbfx9UMUV
=mYK2
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.17-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.17
- Add DU and VIN pin groups on R-Car D3,
- Add HDMI, TMU, and VIN pin groups on R-Car H3 and M3-W,
- Add support for the new R-Car M3-N SoC,
- Small fixes and cleanups.
Mika Westerberg