diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts
index fa0088025b2c..85c95cc551dd 100644
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/am574x-idk.dts
@@ -40,3 +40,7 @@
 	status = "okay";
 	dual_emac;
 };
+
+&m_can0 {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 4740989ed9c4..7191ee6a1b82 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -172,6 +172,7 @@
 			#address-cells = <1>;
 			ranges = <0x51000000 0x51000000 0x3000
 				  0x0	     0x20000000 0x10000000>;
+			dma-ranges;
 			/**
 			 * To enable PCI endpoint mode, disable the pcie1_rc
 			 * node and enable pcie1_ep mode.
@@ -185,7 +186,6 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
-				dma-ranges = <0x02000000 0x0 0x00000000 0x00000000 0x1 0x00000000>;
 				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
@@ -230,6 +230,7 @@
 			#address-cells = <1>;
 			ranges = <0x51800000 0x51800000 0x3000
 				  0x0	     0x30000000 0x10000000>;
+			dma-ranges;
 			status = "disabled";
 			pcie2_rc: pcie@51800000 {
 				reg = <0x51800000 0x2000>, <0x51802000 0x14c>, <0x1000 0x2000>;
@@ -240,7 +241,6 @@
 				device_type = "pci";
 				ranges = <0x81000000 0 0          0x03000 0 0x00010000
 					  0x82000000 0 0x30013000 0x13000 0 0xffed000>;
-				dma-ranges = <0x02000000 0x0 0x00000000 0x00000000 0x1 0x00000000>;
 				bus-range = <0x00 0xff>;
 				#interrupt-cells = <1>;
 				num-lanes = <1>;
diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
index 9067e0ef4240..06fbffa81636 100644
--- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi
+++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
@@ -367,6 +367,8 @@
 };
 
 &mmc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins>;
 	vmmc-supply = <&wl12xx_vmmc>;
 	/* uart2_tx.sdmmc3_dat1 pad as wakeirq */
 	interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
@@ -472,6 +474,37 @@
 		>;
 	};
 
+	/*
+	 * Android uses PIN_OFF_INPUT_PULLDOWN | PIN_INPUT_PULLUP | MUX_MODE3
+	 * for gpio_100, but the internal pull makes wlan flakey on some
+	 * devices. Off mode value should be tested if we have off mode working
+	 * later on.
+	 */
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+		/* 0x4a10008e gpmc_wait2.gpio_100 d23 */
+		OMAP4_IOPAD(0x08e, PIN_INPUT | MUX_MODE3)
+
+		/* 0x4a100102 abe_mcbsp1_dx.sdmmc3_dat2 ab25 */
+		OMAP4_IOPAD(0x102, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a100104 abe_mcbsp1_fsx.sdmmc3_dat3 ac27 */
+		OMAP4_IOPAD(0x104, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a100118 uart2_cts.sdmmc3_clk ab26 */
+		OMAP4_IOPAD(0x118, PIN_INPUT | MUX_MODE1)
+
+		/* 0x4a10011a uart2_rts.sdmmc3_cmd ab27 */
+		OMAP4_IOPAD(0x11a, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a10011c uart2_rx.sdmmc3_dat0 aa25 */
+		OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE1)
+
+		/* 0x4a10011e uart2_tx.sdmmc3_dat1 aa26 */
+		OMAP4_IOPAD(0x11e, PIN_INPUT_PULLUP | MUX_MODE1)
+		>;
+	};
+
 	/* gpmc_ncs0.gpio_50 */
 	poweroff_gpio: pinmux_poweroff_pins {
 		pinctrl-single,pins = <
@@ -690,14 +723,18 @@
 };
 
 /*
- * As uart1 is wired to mdm6600 with rts and cts, we can use the cts pin for
- * uart1 wakeirq.
+ * The uart1 port is wired to mdm6600 with rts and cts. The modem uses gpio_149
+ * for wake-up events for both the USB PHY and the UART. We can use gpio_149
+ * pad as the shared wakeirq for the UART rather than the RX or CTS pad as we
+ * have gpio_149 trigger before the UART transfer starts.
  */
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart1_pins>;
 	interrupts-extended = <&wakeupgen GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH
-			       &omap4_pmx_core 0xfc>;
+			       &omap4_pmx_core 0x110>;
+	uart-has-rtscts;
+	current-speed = <115200>;
 };
 
 &uart3 {