hollalinux
/
linux-sg2042
mirror of https://github.com/sophgo/linux-riscv.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

Renesas ARM Based SoC DT Updates for v4.17 

* Silk board with R-Car E2 (r8a7794) SoC
   - Add r1ex24002 EEPROM to DT
 
     Magnus Damm says "Extend the Silk board support to include U14 which is
     an I2C based EEPROM hooked up to the I2C1 bus."
 
   - Add GPIO keys to DT
 
     Magnus Damm says "Extend the Silk board support to include SW3, SW4,
     SW6 and SW12. They are all connected via GPIO lines and handled by the
     gpio-keys driver"
 
 * Marzen board with R-Car H1 (r7a7779) SoC
   - Add SDHI0 VCCQ Regulator
 
     Magnus Damm says "Add support for the on-board voltage regulator hooked
     up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
     regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
     tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
     OUT goes to the pull-ups for the data pins of SDHI0."
 
 * Porter board with R-Car M3W (r8a7791) SoC
   - Fix HDMI output routing
 
     Laurent Pinchart says "The HDMI encoder is connected to the RGB output
     of the DU, which is port@0, not port@1."
 
 * iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
   iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
   - Enable cmt0
 
 * Stout board with R-Car H2 (r8a7790) SoC
   - Initial support
 
 * Lager board with R-Car H2 (r8a7790) SoC
   - Add CEC clock for HDMI transmitter
 
     Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
     fixed clock for the CEC block. Specify this in the dts to enable CEC
     support."
 
   - Move cec_clock to root node
 
     By definition nodes without a bus address do not belong on the bus
 
 * kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
   - Fix "debounce-interval" property misspelling
 
 * RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
   - Add IPMMU DT nodes
   - Add VSP support
 
 * R-Car Gen2 boards
   - Use I2C demuxer for
 
     This allows run-time switching between alternate I2C IP blocks
 
 * R-Car Gen2 and RZ/G1 SoCs
   - Clean up DT files to ease future maintenance
     + add soc node for IP attached to the bus
     + sort subnodes of soc and root node
     + consistently use single space after =
 
 * R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
   - Reduce size of thermal registers
 
     According to the "User's Manual: Hardware" v2.00 the registers at base
     0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
     case on the r8a73a4 (R-Mobile APE6).
 
     This should not have any runtime affect as mapping granularity is
     PAGE_SIZE.
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAlqr8gsACgkQ189kaWo3
 T74DQw//Th3KG2mycxuvsMEQ2nMRlnDet1Sn3+A85i7TiXs8HLZ7gJlqHV7tEmAV
 Mdflu01Q4Uu6STkLe8MagDl42Hi8B751VSp97RwLUOuWrNHlMVNsBCWYAOnP8LEM
 D7jxlNde5bakP3DlwC/y/evx7cJMt9186QAsqO6AyD6kbw5pdNy8aNjZ4S3sB68W
 Y4HkYFG8ScpNCgfSB2Z60GMIGXAIHBFCullITpzie7zknp57nYn74MEUKhCjxIEm
 PaR+KBDLcckJdsu5VCrHVWDHAYfN3ETx3WLJNn9vxuDqEOHV9Do7AiGyHEmuLAWU
 Aijlp1SHVSwvSXFEodRRvugEy7/7GP6SHT7XdUKcdlp1KrP+YRlS4zccHwUhVn/Z
 G+SCvxVFk902Rk2UFVkk/MayUanxo8VjvDzveWEQr6k3mGmIQt6LugZG4guYgyQh
 A6pkvW8AvUcSX2BDawxKj6rvEDZBLbvKsdybUybHLg7IzCWPzCTg+NKDMlI9rB8I
 wpdDJIX1/Efe1aa85AfNA8yNQBsZzA//gXj+La+vo8N/ptkKkO9EC13rgjVwIepV
 ccUDjssFvUoQy9THW/PwHPczDcj/t9rIfsiilX5zQdt5dqwp0cw5hMAm2wQvdc0n
 4Ge5nBI121eCJ2f4RAghz89t0Dh8yUDdluJCKFHas+x9/JZPAYU=
 =dZnw
 -----END PGP SIGNATURE-----

Merge tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt

Pull "Renesas ARM Based SoC DT Updates for v4.17" from Simon Horman:

* Silk board with R-Car E2 (r8a7794) SoC
  - Add r1ex24002 EEPROM to DT

    Magnus Damm says "Extend the Silk board support to include U14 which is
    an I2C based EEPROM hooked up to the I2C1 bus."

  - Add GPIO keys to DT

    Magnus Damm says "Extend the Silk board support to include SW3, SW4,
    SW6 and SW12. They are all connected via GPIO lines and handled by the
    gpio-keys driver"

* Marzen board with R-Car H1 (r7a7779) SoC
  - Add SDHI0 VCCQ Regulator

    Magnus Damm says "Add support for the on-board voltage regulator hooked
    up to GPIO3_20 on r8a7779 Marzen. The board schematics describes the
    regulator as U4 TPS2110A. Input wise, U4 has D0 fixed to ground, D1
    tied to GPIO3_20 while IN1 is fixed to 3.3V and IN2 is fixed to 1.8V.
    OUT goes to the pull-ups for the data pins of SDHI0."

* Porter board with R-Car M3W (r8a7791) SoC
  - Fix HDMI output routing

    Laurent Pinchart says "The HDMI encoder is connected to the RGB output
    of the DU, which is port@0, not port@1."

* iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM) and
  iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
  - Enable cmt0

* Stout board with R-Car H2 (r8a7790) SoC
  - Initial support

* Lager board with R-Car H2 (r8a7790) SoC
  - Add CEC clock for HDMI transmitter

    Niklas Söderlund says "The adv7511 on the Lager board has a 12 MHz
    fixed clock for the CEC block. Specify this in the dts to enable CEC
    support."

  - Move cec_clock to root node

    By definition nodes without a bus address do not belong on the bus

* kzm9d board with EMMA Mobile EV2 (EMEV2) SoC
  - Fix "debounce-interval" property misspelling

* RZ/G1M (r8a7743) and RZ/G1H (r8a7745) SoCs
  - Add IPMMU DT nodes
  - Add VSP support

* R-Car Gen2 boards
  - Use I2C demuxer for

    This allows run-time switching between alternate I2C IP blocks

* R-Car Gen2 and RZ/G1 SoCs
  - Clean up DT files to ease future maintenance
    + add soc node for IP attached to the bus
    + sort subnodes of soc and root node
    + consistently use single space after =

* R-Car H2 (r8a7790), M3-W (r8a7791) and M3-N (r7a7793) SoCs
  - Reduce size of thermal registers

    According to the "User's Manual: Hardware" v2.00 the registers at base
    0xe61f0000 extend to an offset of 0x10, rather than 0x14 which is the
    case on the r8a73a4 (R-Mobile APE6).

    This should not have any runtime affect as mapping granularity is
    PAGE_SIZE.

* tag 'renesas-dt-for-v4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (47 commits)
  ARM: dts: silk: Add GPIO keys to DT
  ARM: dts: silk: Add r1ex24002 EEPROM to DT
  ARM: dts: marzen: Add SDHI0 VCCQ Regulator
  ARM: dts: stout: Initial r8a7790 Stout board support
  ARM: dts: lager: Move cec_clock to root node
  ARM: dts: kzm9d: Fix "debounce-interval" property misspelling
  ARM: dts: gose: use demuxer for I2C4
  ARM: dts: gose: use demuxer for I2C2
  ARM: dts: silk: use demuxer for I2C1
  ARM: dts: alt: use demuxer for I2C1
  ARM: dts: porter: use demuxer for I2C2
  ARM: dts: koelsch: use demuxer for I2C4
  ARM: dts: koelsch: use demuxer for I2C2
  ARM: dts: lager: use demuxer for IIC3/I2C3
  ARM: dts: lager: use demuxer for IIC2/I2C2
  ARM: dts: r8a7745: Add VSP support
  ARM: dts: r8a7743: Add VSP support
  ARM: dts: r8a7745: Add IPMMU DT nodes
  ARM: dts: r8a7743: Add IPMMU DT nodes
  ARM: dts: r8a7745: sort subnodes of soc node
  ...
This commit is contained in:
Arnd Bergmann 2018-03-27 13:32:53 +02:00
parent e5bdf7775e a24a5821a6
commit cdcdbbf350
19 changed files with 8370 additions and 7271 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

1
arch/arm/boot/dts/Makefile
View File

@ -797,6 +797,7 @@ dtb-$(CONFIG_ARCH_RENESAS) += \
r8a7778-bockw.dtb \
r8a7779-marzen.dtb \
r8a7790-lager.dtb \
r8a7790-stout.dtb \
r8a7791-koelsch.dtb \
r8a7791-porter.dtb \
r8a7792-blanche.dtb \

8
arch/arm/boot/dts/emev2-kzm9d.dts
View File

@ -38,28 +38,28 @@
#size-cells = <0>;
one {
debounce_interval = <50>;
debounce-interval = <50>;
wakeup-source;
label = "DSW2-1";
linux,code = <KEY_1>;
gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
};
two {
debounce_interval = <50>;
debounce-interval = <50>;
wakeup-source;
label = "DSW2-2";
linux,code = <KEY_2>;
gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
};
three {
debounce_interval = <50>;
debounce-interval = <50>;
wakeup-source;
label = "DSW2-3";
linux,code = <KEY_3>;
gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
};
four {
debounce_interval = <50>;
debounce-interval = <50>;
wakeup-source;
label = "DSW2-4";
linux,code = <KEY_4>;

4
arch/arm/boot/dts/r8a7743-iwg20m.dtsi
View File

@ -34,6 +34,10 @@
};
};
&cmt0 {
status = "okay";
};
&extal_clk {
clock-frequency = <20000000>;
};

1218
arch/arm/boot/dts/r8a7743.dtsi
View File

File diff suppressed because it is too large Load Diff

4
arch/arm/boot/dts/r8a7745-iwg22m.dtsi
View File

@ -29,6 +29,10 @@
};
};
&cmt0 {
status = "okay";
};
&extal_clk {
clock-frequency = <20000000>;
};

1160
arch/arm/boot/dts/r8a7745.dtsi
View File

File diff suppressed because it is too large Load Diff

14
arch/arm/boot/dts/r8a7779-marzen.dts
View File

@ -42,6 +42,19 @@
regulator-always-on;
};
vccq_sdhi0: regulator-vccq-sdhi0 {
compatible = "regulator-gpio";
regulator-name = "SDHI0 VccQ";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1
1800000 0>;
};
ethernet@18000000 {
compatible = "smsc,lan9220", "smsc,lan9115";
reg = <0x18000000 0x100>;
@ -243,6 +256,7 @@
pinctrl-names = "default";
vmmc-supply = <&fixedregulator3v3>;
vqmmc-supply = <&vccq_sdhi0>;
bus-width = <4>;
status = "okay";
};

293
arch/arm/boot/dts/r8a7790-lager.dts
View File

@ -51,8 +51,11 @@
serial0 = &scif0;
serial1 = &scifa1;
i2c8 = &gpioi2c1;
i2c9 = &gpioi2c2;
i2c10 = &i2cexio0;
i2c11 = &i2cexio1;
i2c12 = &i2chdmi;
i2c13 = &i2cpwr;
};
chosen {
@ -244,6 +247,12 @@
};
};
cec_clock: cec-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <12000000>;
};
hdmi-out {
compatible = "hdmi-connector";
type = "a";
@ -272,8 +281,18 @@
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio1 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
gpioi2c2: i2c-9 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio5 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio5 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
@ -308,6 +327,138 @@
#address-cells = <1>;
#size-cells = <0>;
};
/*
* IIC2 and I2C2 may be switched using pinmux.
* A fallback to GPIO is also provided.
*/
i2chdmi: i2c-12 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic2>, <&i2c2>, <&gpioi2c2>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin1>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep0>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio1>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
clocks = <&cec_clock>;
clock-names = "cec";
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_lvds0>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio1>;
interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
};
/*
* IIC3 and I2C3 may be switched using pinmux.
* IIC3/I2C3 does not appear to support fallback to GPIO.
*/
i2cpwr: i2c-13 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&iic3>, <&i2c3>;
i2c-bus-name = "i2c-pwr";
#address-cells = <1>;
#size-cells = <0>;
pmic@58 {
compatible = "dlg,da9063";
reg = <0x58>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
rtc {
compatible = "dlg,da9063-rtc";
};
wdt {
compatible = "dlg,da9063-watchdog";
};
};
vdd_dvfs: regulator@68 {
compatible = "dlg,da9210";
reg = <0x68>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
};
};
};
&du {
@ -437,11 +588,21 @@
function = "iic1";
};
i2c2_pins: i2c2 {
groups = "i2c2";
function = "i2c2";
};
iic2_pins: iic2 {
groups = "iic2";
function = "iic2";
};
i2c3_pins: i2c3 {
groups = "i2c3";
function = "i2c3";
};
iic3_pins: iic3 {
groups = "iic3";
function = "iic3";
@ -643,124 +804,28 @@
pinctrl-names = "i2c-exio1";
};
&iic2 {
status = "okay";
pinctrl-0 = <&iic2_pins>;
pinctrl-names = "default";
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "i2c-hdmi";
clock-frequency = <100000>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin1>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep0>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio1>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_lvds0>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio1>;
interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
};
&iic3 {
pinctrl-names = "default";
&iic2 {
pinctrl-0 = <&iic2_pins>;
pinctrl-names = "i2c-hdmi";
clock-frequency = <100000>;
};
&i2c3 {
pinctrl-0 = <&i2c3_pins>;
pinctrl-names = "i2c-pwr";
};
&iic3 {
pinctrl-0 = <&iic3_pins>;
status = "okay";
pmic@58 {
compatible = "dlg,da9063";
reg = <0x58>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
rtc {
compatible = "dlg,da9063-rtc";
};
wdt {
compatible = "dlg,da9063-watchdog";
};
};
vdd_dvfs: regulator@68 {
compatible = "dlg,da9210";
reg = <0x68>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
};
pinctrl-names = "i2c-pwr";
};
&pci0 {

363
arch/arm/boot/dts/r8a7790-stout.dts Normal file
View File

@ -0,0 +1,363 @@
// SPDX-License-Identifier: GPL-2.0
/*
* Device Tree Source for the Stout board
*
* Copyright (C) 2018 Marek Vasut <marek.vasut@gmail.com>
*/
/dts-v1/;
#include "r8a7790.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Stout";
compatible = "renesas,stout", "renesas,r8a7790";
aliases {
serial0 = &scifa0;
};
chosen {
bootargs = "ignore_loglevel rw root=/dev/nfs ip=dhcp";
stdout-path = "serial0:115200n8";
};
memory@40000000 {
device_type = "memory";
reg = <0 0x40000000 0 0x40000000>;
};
leds {
compatible = "gpio-leds";
led1 {
gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
};
led2 {
gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
};
led3 {
gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
};
led5 {
gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
};
};
fixedregulator3v3: regulator-3v3 {
compatible = "regulator-fixed";
regulator-name = "fixed-3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
};
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
regulator-name = "SDHI0 Vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
hdmi-out {
compatible = "hdmi-connector";
type = "a";
port {
hdmi_con_out: endpoint {
remote-endpoint = <&adv7511_out>;
};
};
};
osc1_clk: osc1-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <148500000>;
};
osc4_clk: osc4-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <12000000>;
};
};
&du {
pinctrl-0 = <&du_pins>;
pinctrl-names = "default";
status = "okay";
clocks = <&cpg CPG_MOD 724>, <&cpg CPG_MOD 723>, <&cpg CPG_MOD 722>,
<&cpg CPG_MOD 726>, <&cpg CPG_MOD 725>,
<&osc1_clk>;
clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1", "dclkin.0";
ports {
port@0 {
endpoint {
remote-endpoint = <&adv7511_in>;
};
};
port@1 {
lvds_connector0: endpoint {
};
};
port@2 {
lvds_connector1: endpoint {
};
};
};
};
&extal_clk {
clock-frequency = <20000000>;
};
&pfc {
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
du_pins: du {
groups = "du_rgb888", "du_sync_1", "du_clk_out_0";
function = "du";
};
scifa0_pins: scifa0 {
groups = "scifa0_data_b";
function = "scifa0";
};
scif_clk_pins: scif_clk {
groups = "scif_clk";
function = "scif_clk";
};
ether_pins: ether {
groups = "eth_link", "eth_mdio", "eth_rmii";
function = "eth";
};
phy1_pins: phy1 {
groups = "intc_irq1";
function = "intc";
};
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <3300>;
};
qspi_pins: qspi {
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
iic2_pins: iic2 {
groups = "iic2_b";
function = "iic2";
};
iic3_pins: iic3 {
groups = "iic3";
function = "iic3";
};
usb0_pins: usb0 {
groups = "usb0";
function = "usb0";
};
};
&ether {
pinctrl-0 = <&ether_pins &phy1_pins>;
pinctrl-names = "default";
phy-handle = <&phy1>;
renesas,ether-link-active-low;
status = "okay";
phy1: ethernet-phy@1 {
reg = <1>;
interrupt-parent = <&irqc0>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
micrel,led-mode = <1>;
};
};
&cmt0 {
status = "okay";
};
&qspi {
pinctrl-0 = <&qspi_pins>;
pinctrl-names = "default";
status = "okay";
flash: flash@0 {
compatible = "spansion,s25fl512s", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <30000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
spi-cpha;
spi-cpol;
m25p,fast-read;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "loader";
reg = <0x00000000 0x00080000>;
read-only;
};
partition@80000 {
label = "uboot";
reg = <0x00080000 0x00040000>;
read-only;
};
partition@c0000 {
label = "uboot-env";
reg = <0x000c0000 0x00040000>;
read-only;
};
partition@100000 {
label = "flash";
reg = <0x00100000 0x03f00000>;
};
};
};
};
&scifa0 {
pinctrl-0 = <&scifa0_pins>;
pinctrl-names = "default";
status = "okay";
};
&scif_clk {
clock-frequency = <14745600>;
};
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
pinctrl-names = "default";
vmmc-supply = <&vcc_sdhi0>;
cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>;
status = "okay";
};
&cpu0 {
cpu0-supply = <&vdd_dvfs>;
};
&iic2 {
status = "okay";
pinctrl-0 = <&iic2_pins>;
pinctrl-names = "default";
clock-frequency = <100000>;
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio1>;
interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
clocks = <&osc4_clk>;
clock-names = "cec";
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
};
&iic3 {
pinctrl-names = "default";
pinctrl-0 = <&iic3_pins>;
status = "okay";
pmic@58 {
compatible = "dlg,da9063";
reg = <0x58>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
rtc {
compatible = "dlg,da9063-rtc";
};
wdt {
compatible = "dlg,da9063-watchdog";
};
};
vdd_dvfs: regulator@68 {
compatible = "dlg,da9210";
reg = <0x68>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
};
vdd: regulator@70 {
compatible = "dlg,da9210";
reg = <0x70>;
interrupt-parent = <&irqc0>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-boot-on;
regulator-always-on;
};
};
&pci0 {
status = "okay";
pinctrl-0 = <&usb0_pins>;
pinctrl-names = "default";
};
&usbphy {
status = "okay";
};

3027
arch/arm/boot/dts/r8a7790.dtsi
View File

File diff suppressed because it is too large Load Diff

232
arch/arm/boot/dts/r8a7791-koelsch.dts
View File

@ -51,7 +51,11 @@
serial0 = &scif0;
serial1 = &scif1;
i2c9 = &gpioi2c1;
i2c10 = &gpioi2c2;
i2c11 = &gpioi2c4;
i2c12 = &i2cexio1;
i2c13 = &i2chdmi;
i2c14 = &i2cexio4;
};
chosen {
@ -312,8 +316,28 @@
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
sda-gpios = <&gpio7 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio7 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio7 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
gpioi2c2: i2c-10 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio2 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio2 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
gpioi2c4: i2c-11 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio7 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio7 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
@ -328,6 +352,115 @@
#address-cells = <1>;
#size-cells = <0>;
};
/*
* A fallback to GPIO is provided for I2C2.
*/
i2chdmi: i2c-13 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c2>, <&gpioi2c2>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin1>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
clocks = <&cec_clock>;
clock-names = "cec";
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio4>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
eeprom@50 {
compatible = "renesas,r1ex24002", "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
};
/*
* I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
* A fallback to GPIO is provided.
*/
i2cexio4: i2c-14 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c4>, <&gpioi2c4>;
i2c-bus-name = "i2c-exio4";
#address-cells = <1>;
#size-cells = <0>;
};
};
&du {
@ -371,6 +504,11 @@
function = "i2c2";
};
i2c4_pins: i2c4 {
groups = "i2c4_c";
function = "i2c4";
};
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
@ -621,96 +759,14 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <100000>;
};
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin1>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
clocks = <&cec_clock>;
clock-names = "cec";
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio4>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
eeprom@50 {
compatible = "renesas,r1ex24002", "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
&i2c4 {
pinctrl-0 = <&i2c4_pins>;
pinctrl-names = "i2c-exio4";
};
&i2c6 {

130
arch/arm/boot/dts/r8a7791-porter.dts
View File

@ -29,6 +29,8 @@
aliases {
serial0 = &scif0;
i2c9 = &gpioi2c2;
i2c10 = &i2chdmi;
};
chosen {
@ -135,6 +137,78 @@
clocks = <&x14_clk>;
};
};
gpioi2c2: i2c-9 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio2 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio2 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
/*
* A fallback to GPIO is provided for I2C2.
*/
i2chdmi: i2c-10 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c2>, <&gpioi2c2>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
ak4642: codec@12 {
compatible = "asahi-kasei,ak4642";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin0>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin0ep>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
};
};
&extal_clk {
@ -296,61 +370,9 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <400000>;
ak4642: codec@12 {
compatible = "asahi-kasei,ak4642";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin0>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin0ep>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
};
&sata0 {
@ -425,7 +447,7 @@
"dclkin.0", "dclkin.1";
ports {
port@1 {
port@0 {
endpoint {
remote-endpoint = <&adv7511_in>;
};

3176
arch/arm/boot/dts/r8a7791.dtsi
View File

File diff suppressed because it is too large Load Diff

498
arch/arm/boot/dts/r8a7792.dtsi
View File

@ -101,63 +101,6 @@
#size-cells = <2>;
ranges;
apmu@e6152000 {
compatible = "renesas,r8a7792-apmu", "renesas,apmu";
reg = <0 0xe6152000 0 0x188>;
cpus = <&cpu0 &cpu1>;
};
gic: interrupt-controller@f1001000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
interrupt-controller;
reg = <0 0xf1001000 0 0x1000>,
<0 0xf1002000 0 0x2000>,
<0 0xf1004000 0 0x2000>,
<0 0xf1006000 0 0x2000>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&cpg CPG_MOD 408>;
clock-names = "clk";
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 408>;
};
irqc: interrupt-controller@e61c0000 {
compatible = "renesas,irqc-r8a7792", "renesas,irqc";
#interrupt-cells = <2>;
interrupt-controller;
reg = <0 0xe61c0000 0 0x200>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 407>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 407>;
};
rst: reset-controller@e6160000 {
compatible = "renesas,r8a7792-rst";
reg = <0 0xe6160000 0 0x0100>;
};
prr: chipid@ff000044 {
compatible = "renesas,prr";
reg = <0 0xff000044 0 4>;
};
sysc: system-controller@e6180000 {
compatible = "renesas,r8a7792-sysc";
reg = <0 0xe6180000 0 0x0200>;
#power-domain-cells = <1>;
};
pfc: pin-controller@e6060000 {
compatible = "renesas,pfc-r8a7792";
reg = <0 0xe6060000 0 0x144>;
};
gpio0: gpio@e6050000 {
compatible = "renesas,gpio-r8a7792",
"renesas,rcar-gen2-gpio";
@ -338,6 +281,155 @@
resets = <&cpg 913>;
};
pfc: pin-controller@e6060000 {
compatible = "renesas,pfc-r8a7792";
reg = <0 0xe6060000 0 0x144>;
};
cpg: clock-controller@e6150000 {
compatible = "renesas,r8a7792-cpg-mssr";
reg = <0 0xe6150000 0 0x1000>;
clocks = <&extal_clk>;
clock-names = "extal";
#clock-cells = <2>;
#power-domain-cells = <0>;
#reset-cells = <1>;
};
apmu@e6152000 {
compatible = "renesas,r8a7792-apmu", "renesas,apmu";
reg = <0 0xe6152000 0 0x188>;
cpus = <&cpu0 &cpu1>;
};
rst: reset-controller@e6160000 {
compatible = "renesas,r8a7792-rst";
reg = <0 0xe6160000 0 0x0100>;
};
sysc: system-controller@e6180000 {
compatible = "renesas,r8a7792-sysc";
reg = <0 0xe6180000 0 0x0200>;
#power-domain-cells = <1>;
};
irqc: interrupt-controller@e61c0000 {
compatible = "renesas,irqc-r8a7792", "renesas,irqc";
#interrupt-cells = <2>;
interrupt-controller;
reg = <0 0xe61c0000 0 0x200>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 407>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 407>;
};
icram0: sram@e63a0000 {
compatible = "mmio-sram";
reg = <0 0xe63a0000 0 0x12000>;
};
icram1: sram@e63c0000 {
compatible = "mmio-sram";
reg = <0 0xe63c0000 0 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0xe63c0000 0x1000>;
smp-sram@0 {
compatible = "renesas,smp-sram";
reg = <0 0x10>;
};
};
/* I2C doesn't need pinmux */
i2c0: i2c@e6508000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 931>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c1: i2c@e6518000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6518000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 930>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c2: i2c@e6530000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6530000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 929>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c3: i2c@e6540000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6540000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 928>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c4: i2c@e6520000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6520000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 927>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 927>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c5: i2c@e6528000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6528000 0 0x40>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 925>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 925>;
i2c-scl-internal-delay-ns = <110>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
dmac0: dma-controller@e6700000 {
compatible = "renesas,dmac-r8a7792",
"renesas,rcar-dmac";
@ -404,6 +496,35 @@
dma-channels = <15>;
};
avb: ethernet@e6800000 {
compatible = "renesas,etheravb-r8a7792",
"renesas,etheravb-rcar-gen2";
reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 812>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
qspi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7792", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 917>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>,
<&dmac1 0x17>, <&dmac1 0x18>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 917>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
scif0: serial@e6e60000 {
compatible = "renesas,scif-r8a7792",
"renesas,rcar-gen2-scif", "renesas,scif";
@ -500,162 +621,6 @@
status = "disabled";
};
icram0: sram@e63a0000 {
compatible = "mmio-sram";
reg = <0 0xe63a0000 0 0x12000>;
};
icram1: sram@e63c0000 {
compatible = "mmio-sram";
reg = <0 0xe63c0000 0 0x1000>;
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0xe63c0000 0x1000>;
smp-sram@0 {
compatible = "renesas,smp-sram";
reg = <0 0x10>;
};
};
sdhi0: sd@ee100000 {
compatible = "renesas,sdhi-r8a7792",
"renesas,rcar-gen2-sdhi";
reg = <0 0xee100000 0 0x328>;
interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
<&dmac1 0xcd>, <&dmac1 0xce>;
dma-names = "tx", "rx", "tx", "rx";
clocks = <&cpg CPG_MOD 314>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 314>;
status = "disabled";
};
jpu: jpeg-codec@fe980000 {
compatible = "renesas,jpu-r8a7792",
"renesas,rcar-gen2-jpu";
reg = <0 0xfe980000 0 0x10300>;
interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 106>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 106>;
};
avb: ethernet@e6800000 {
compatible = "renesas,etheravb-r8a7792",
"renesas,etheravb-rcar-gen2";
reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 812>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 812>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
/* I2C doesn't need pinmux */
i2c0: i2c@e6508000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6508000 0 0x40>;
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 931>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c1: i2c@e6518000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6518000 0 0x40>;
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 930>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c2: i2c@e6530000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6530000 0 0x40>;
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 929>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c3: i2c@e6540000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6540000 0 0x40>;
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 928>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c4: i2c@e6520000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6520000 0 0x40>;
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 927>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 927>;
i2c-scl-internal-delay-ns = <6>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
i2c5: i2c@e6528000 {
compatible = "renesas,i2c-r8a7792",
"renesas,rcar-gen2-i2c";
reg = <0 0xe6528000 0 0x40>;
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 925>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 925>;
i2c-scl-internal-delay-ns = <110>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
qspi: spi@e6b10000 {
compatible = "renesas,qspi-r8a7792", "renesas,qspi";
reg = <0 0xe6b10000 0 0x2c>;
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 917>;
dmas = <&dmac0 0x17>, <&dmac0 0x18>,
<&dmac1 0x17>, <&dmac1 0x18>;
dma-names = "tx", "rx", "tx", "rx";
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 917>;
num-cs = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
msiof0: spi@e6e20000 {
compatible = "renesas,msiof-r8a7792",
"renesas,rcar-gen2-msiof";
@ -688,34 +653,6 @@
status = "disabled";
};
du: display@feb00000 {
compatible = "renesas,du-r8a7792";
reg = <0 0xfeb00000 0 0x40000>;
reg-names = "du";
interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 724>,
<&cpg CPG_MOD 723>;
clock-names = "du.0", "du.1";
status = "disabled";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
du_out_rgb0: endpoint {
};
};
port@1 {
reg = <1>;
du_out_rgb1: endpoint {
};
};
};
};
can0: can@e6e80000 {
compatible = "renesas,can-r8a7792",
"renesas,rcar-gen2-can";
@ -808,6 +745,36 @@
status = "disabled";
};
sdhi0: sd@ee100000 {
compatible = "renesas,sdhi-r8a7792",
"renesas,rcar-gen2-sdhi";
reg = <0 0xee100000 0 0x328>;
interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
<&dmac1 0xcd>, <&dmac1 0xce>;
dma-names = "tx", "rx", "tx", "rx";
clocks = <&cpg CPG_MOD 314>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 314>;
status = "disabled";
};
gic: interrupt-controller@f1001000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
interrupt-controller;
reg = <0 0xf1001000 0 0x1000>,
<0 0xf1002000 0 0x2000>,
<0 0xf1004000 0 0x2000>,
<0 0xf1006000 0 0x2000>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
IRQ_TYPE_LEVEL_HIGH)>;
clocks = <&cpg CPG_MOD 408>;
clock-names = "clk";
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 408>;
};
vsp@fe928000 {
compatible = "renesas,vsp1";
reg = <0 0xfe928000 0 0x8000>;
@ -835,14 +802,47 @@
resets = <&cpg 127>;
};
cpg: clock-controller@e6150000 {
compatible = "renesas,r8a7792-cpg-mssr";
reg = <0 0xe6150000 0 0x1000>;
clocks = <&extal_clk>;
clock-names = "extal";
#clock-cells = <2>;
#power-domain-cells = <0>;
#reset-cells = <1>;
jpu: jpeg-codec@fe980000 {
compatible = "renesas,jpu-r8a7792",
"renesas,rcar-gen2-jpu";
reg = <0 0xfe980000 0 0x10300>;
interrupts = <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 106>;
power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
resets = <&cpg 106>;
};
du: display@feb00000 {
compatible = "renesas,du-r8a7792";
reg = <0 0xfeb00000 0 0x40000>;
reg-names = "du";
interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 724>,
<&cpg CPG_MOD 723>;
clock-names = "du.0", "du.1";
status = "disabled";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
du_out_rgb0: endpoint {
};
};
port@1 {
reg = <1>;
du_out_rgb1: endpoint {
};
};
};
};
prr: chipid@ff000044 {
compatible = "renesas,prr";
reg = <0 0xff000044 0 4>;
};
};

252
arch/arm/boot/dts/r8a7793-gose.dts
View File

@ -48,6 +48,10 @@
aliases {
serial0 = &scif0;
serial1 = &scif1;
i2c9 = &gpioi2c2;
i2c10 = &gpioi2c4;
i2c11 = &i2chdmi;
i2c12 = &i2cexio4;
};
chosen {
@ -296,6 +300,146 @@
#clock-cells = <0>;
clock-frequency = <148500000>;
};
gpioi2c2: i2c-9 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio2 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio2 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
gpioi2c4: i2c-10 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio7 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio7 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
/*
* A fallback to GPIO is provided for I2C2.
*/
i2chdmi: i2c-11 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c2>, <&gpioi2c2>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180cp";
reg = <0x20>;
remote = <&vin1>;
port {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7180_in: endpoint {
remote-endpoint = <&composite_con_in>;
};
};
port@3 {
reg = <3>;
adv7180_out: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep>;
};
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio4>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
port {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
eeprom@50 {
compatible = "renesas,r1ex24002", "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
};
/*
* I2C4 is routed to EXIO connector E, pins 37 (SCL) + 39 (SDA).
* A fallback to GPIO is provided.
*/
i2cexio4: i2c-12 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c4>, <&gpioi2c4>;
i2c-bus-name = "i2c-exio4";
#address-cells = <1>;
#size-cells = <0>;
};
};
&du {
@ -334,6 +478,11 @@
function = "i2c2";
};
i2c4_pins: i2c4 {
groups = "i2c4_c";
function = "i2c4";
};
du_pins: du {
groups = "du_rgb888", "du_sync", "du_disp", "du_clk_out_0";
function = "du";
@ -544,107 +693,11 @@
&i2c2 {
pinctrl-0 = <&i2c2_pins>;
pinctrl-names = "default";
pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <100000>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180cp";
reg = <0x20>;
remote = <&vin1>;
port {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7180_in: endpoint {
remote-endpoint = <&composite_con_in>;
};
};
port@3 {
reg = <3>;
adv7180_out: endpoint {
bus-width = <8>;
remote-endpoint = <&vin1ep>;
};
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio3>;
interrupts = <29 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con_out>;
};
};
};
};
hdmi-in@4c {
compatible = "adi,adv7612";
reg = <0x4c>;
interrupt-parent = <&gpio4>;
interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
default-input = <0>;
port {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7612_in: endpoint {
remote-endpoint = <&hdmi_con_in>;
};
};
port@2 {
reg = <2>;
adv7612_out: endpoint {
remote-endpoint = <&vin0ep2>;
};
};
};
};
eeprom@50 {
compatible = "renesas,r1ex24002", "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
};
&i2c6 {
@ -668,6 +721,11 @@
};
};
&i2c4 {
pinctrl-0 = <&i2c4_pins>;
pinctrl-names = "i2c-exio4";
};
&rcar_sound {
pinctrl-0 = <&sound_pins &sound_clk_pins>;
pinctrl-names = "default";

2494
arch/arm/boot/dts/r8a7793.dtsi
View File

File diff suppressed because it is too large Load Diff

53
arch/arm/boot/dts/r8a7794-alt.dts
View File

@ -18,7 +18,9 @@
aliases {
serial0 = &scif2;
i2c9 = &gpioi2c1;
i2c10 = &gpioi2c4;
i2c11 = &i2chdmi;
i2c12 = &i2cexio4;
};
@ -138,16 +140,49 @@
clock-frequency = <148500000>;
};
gpioi2c1: i2c-9 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};
gpioi2c4: i2c-10 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
sda-gpios = <&gpio4 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
scl-gpios = <&gpio4 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio4 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
/*
* A fallback to GPIO is provided for I2C1.
*/
i2chdmi: i2c-11 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c1>, <&gpioi2c1>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin0>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin0ep>;
};
};
};
};
/*
* I2C4 is routed to EXIO connector B, pins 73 (SCL) + 74 (SDA).
* A fallback to GPIO is provided.
@ -324,23 +359,9 @@
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
pinctrl-names = "default";
pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <400000>;
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin0>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin0ep>;
};
};
};
};
&i2c4 {

189
arch/arm/boot/dts/r8a7794-silk.dts
View File

@ -24,6 +24,7 @@
/dts-v1/;
#include "r8a7794.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "SILK";
@ -31,6 +32,8 @@
aliases {
serial0 = &scif2;
i2c9 = &gpioi2c1;
i2c10 = &i2chdmi;
};
chosen {
@ -43,6 +46,60 @@
reg = <0 0x40000000 0 0x40000000>;
};
gpio-keys {
compatible = "gpio-keys";
key-3 {
gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
linux,code = <KEY_3>;
label = "SW3";
wakeup-source;
debounce-interval = <20>;
};
key-4 {
gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_4>;
label = "SW4";
wakeup-source;
debounce-interval = <20>;
};
key-6 {
gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_6>;
label = "SW6";
wakeup-source;
debounce-interval = <20>;
};
key-a {
gpios = <&gpio3 9 GPIO_ACTIVE_LOW>;
linux,code = <KEY_A>;
label = "SW12-1";
wakeup-source;
debounce-interval = <20>;
};
key-b {
gpios = <&gpio3 10 GPIO_ACTIVE_LOW>;
linux,code = <KEY_B>;
label = "SW12-2";
wakeup-source;
debounce-interval = <20>;
};
key-c {
gpios = <&gpio3 11 GPIO_ACTIVE_LOW>;
linux,code = <KEY_C>;
label = "SW12-3";
wakeup-source;
debounce-interval = <20>;
};
key-d {
gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
linux,code = <KEY_D>;
label = "SW12-4";
wakeup-source;
debounce-interval = <20>;
};
};
d3_3v: regulator-d3-3v {
compatible = "regulator-fixed";
regulator-name = "D3.3V";
@ -153,6 +210,84 @@
clocks = <&x9_clk>;
};
};
gpioi2c1: i2c-9 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "i2c-gpio";
status = "disabled";
scl-gpios = <&gpio4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
i2c-gpio,delay-us = <5>;
};
/*
* A fallback to GPIO is provided for I2C1.
*/
i2chdmi: i2c-10 {
compatible = "i2c-demux-pinctrl";
i2c-parent = <&i2c1>, <&gpioi2c1>;
i2c-bus-name = "i2c-hdmi";
#address-cells = <1>;
#size-cells = <0>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin0>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin0ep>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio5>;
interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb0>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
eeprom@50 {
compatible = "renesas,r1ex24002", "atmel,24c02";
reg = <0x50>;
pagesize = <16>;
};
};
};
&extal_clk {
@ -268,61 +403,9 @@
&i2c1 {
pinctrl-0 = <&i2c1_pins>;
pinctrl-names = "default";
pinctrl-names = "i2c-hdmi";
status = "okay";
clock-frequency = <400000>;
ak4643: codec@12 {
compatible = "asahi-kasei,ak4643";
#sound-dai-cells = <0>;
reg = <0x12>;
};
composite-in@20 {
compatible = "adi,adv7180";
reg = <0x20>;
remote = <&vin0>;
port {
adv7180: endpoint {
bus-width = <8>;
remote-endpoint = <&vin0ep>;
};
};
};
hdmi@39 {
compatible = "adi,adv7511w";
reg = <0x39>;
interrupt-parent = <&gpio5>;
interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
adi,input-depth = <8>;
adi,input-colorspace = "rgb";
adi,input-clock = "1x";
adi,input-style = <1>;
adi,input-justification = "evenly";
ports {
#address-cells = <1>;
#size-cells = <0>;
port@0 {
reg = <0>;
adv7511_in: endpoint {
remote-endpoint = <&du_out_rgb0>;
};
};
port@1 {
reg = <1>;
adv7511_out: endpoint {
remote-endpoint = <&hdmi_con>;
};
};
};
};
};
&mmcif0 {

2525
arch/arm/boot/dts/r8a7794.dtsi
View File

File diff suppressed because it is too large Load Diff