diff --git a/include/linux/nl80211.h b/include/linux/nl80211.h index a18760684fc9..f795cb7dccdd 100644 --- a/include/linux/nl80211.h +++ b/include/linux/nl80211.h @@ -1536,7 +1536,11 @@ enum nl80211_iftype { * @NL80211_STA_FLAG_WME: station is WME/QoS capable * @NL80211_STA_FLAG_MFP: station uses management frame protection * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated - * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer + * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should + * only be used in managed mode (even in the flags mask). Note that the + * flag can't be changed, it is only valid while adding a station, and + * attempts to change it will silently be ignored (rather than rejected + * as errors.) * @NL80211_STA_FLAG_MAX: highest station flag number currently defined * @__NL80211_STA_FLAG_AFTER_LAST: internal use */ diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 150c0ee714c2..5eda5933ae01 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -1346,7 +1346,12 @@ struct cfg80211_gtk_rekey_data { * * @add_station: Add a new station. * @del_station: Remove a station; @mac may be NULL to remove all stations. - * @change_station: Modify a given station. + * @change_station: Modify a given station. Note that flags changes are not much + * validated in cfg80211, in particular the auth/assoc/authorized flags + * might come to the driver in invalid combinations -- make sure to check + * them, also against the existing state! Also, supported_rates changes are + * not checked in station mode -- drivers need to reject (or ignore) them + * for anything but TDLS peers. * @get_station: get station information for the station identified by @mac * @dump_station: dump station callback -- resume dump at index @idx * diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c index 393b2a4445b8..944051b43bad 100644 --- a/net/mac80211/cfg.c +++ b/net/mac80211/cfg.c @@ -976,6 +976,14 @@ static int ieee80211_change_station(struct wiphy *wiphy, return -EINVAL; } + /* in station mode, supported rates are only valid with TDLS */ + if (sdata->vif.type == NL80211_IFTYPE_STATION && + params->supported_rates && + !test_sta_flag(sta, WLAN_STA_TDLS_PEER)) { + rcu_read_unlock(); + return -EINVAL; + } + if (params->vlan && params->vlan != sta->sdata->dev) { vlansdata = IEEE80211_DEV_TO_SUB_IF(params->vlan); diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index d86428145c32..b07c4fc4ae22 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -2579,6 +2579,9 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) params.ht_capa = nla_data(info->attrs[NL80211_ATTR_HT_CAPABILITY]); + if (!rdev->ops->change_station) + return -EOPNOTSUPP; + if (parse_station_flags(info, ¶ms)) return -EINVAL; @@ -2590,73 +2593,84 @@ static int nl80211_set_station(struct sk_buff *skb, struct genl_info *info) params.plink_state = nla_get_u8(info->attrs[NL80211_ATTR_STA_PLINK_STATE]); - params.vlan = get_vlan(info, rdev); - if (IS_ERR(params.vlan)) - return PTR_ERR(params.vlan); - - /* validate settings */ - err = 0; - switch (dev->ieee80211_ptr->iftype) { case NL80211_IFTYPE_AP: case NL80211_IFTYPE_AP_VLAN: case NL80211_IFTYPE_P2P_GO: /* disallow mesh-specific things */ if (params.plink_action) - err = -EINVAL; + return -EINVAL; + + /* TDLS can't be set, ... */ + if (params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) + return -EINVAL; + /* + * ... but don't bother the driver with it. This works around + * a hostapd/wpa_supplicant issue -- it always includes the + * TLDS_PEER flag in the mask even for AP mode. + */ + params.sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); + + /* accept only the listed bits */ + if (params.sta_flags_mask & + ~(BIT(NL80211_STA_FLAG_AUTHORIZED) | + BIT(NL80211_STA_FLAG_SHORT_PREAMBLE) | + BIT(NL80211_STA_FLAG_WME) | + BIT(NL80211_STA_FLAG_MFP))) + return -EINVAL; + + /* must be last in here for error handling */ + params.vlan = get_vlan(info, rdev); + if (IS_ERR(params.vlan)) + return PTR_ERR(params.vlan); break; case NL80211_IFTYPE_P2P_CLIENT: case NL80211_IFTYPE_STATION: /* disallow things sta doesn't support */ if (params.plink_action) - err = -EINVAL; - if (params.vlan) - err = -EINVAL; - if (params.supported_rates && - !(params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER))) - err = -EINVAL; + return -EINVAL; if (params.ht_capa) - err = -EINVAL; + return -EINVAL; if (params.listen_interval >= 0) - err = -EINVAL; - if (params.sta_flags_mask & - ~(BIT(NL80211_STA_FLAG_AUTHORIZED) | - BIT(NL80211_STA_FLAG_TDLS_PEER))) - err = -EINVAL; - /* can't change the TDLS bit */ - if (!(params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) && - (params.sta_flags_mask & BIT(NL80211_STA_FLAG_TDLS_PEER))) - err = -EINVAL; + return -EINVAL; + /* + * Don't allow userspace to change the TDLS_PEER flag, + * but silently ignore attempts to change it since we + * don't have state here to verify that it doesn't try + * to change the flag. + */ + params.sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); + + /* reject any changes other than AUTHORIZED */ + if (params.sta_flags_mask & ~BIT(NL80211_STA_FLAG_AUTHORIZED)) + return -EINVAL; break; case NL80211_IFTYPE_MESH_POINT: /* disallow things mesh doesn't support */ if (params.vlan) - err = -EINVAL; + return -EINVAL; if (params.ht_capa) - err = -EINVAL; + return -EINVAL; if (params.listen_interval >= 0) - err = -EINVAL; + return -EINVAL; + /* + * No special handling for TDLS here -- the userspace + * mesh code doesn't have this bug. + */ if (params.sta_flags_mask & ~(BIT(NL80211_STA_FLAG_AUTHENTICATED) | BIT(NL80211_STA_FLAG_MFP) | BIT(NL80211_STA_FLAG_AUTHORIZED))) - err = -EINVAL; + return -EINVAL; break; default: - err = -EINVAL; + return -EOPNOTSUPP; } - if (err) - goto out; - - if (!rdev->ops->change_station) { - err = -EOPNOTSUPP; - goto out; - } + /* be aware of params.vlan when changing code here */ err = rdev->ops->change_station(&rdev->wiphy, dev, mac_addr, ¶ms); - out: if (params.vlan) dev_put(params.vlan); @@ -2711,70 +2725,81 @@ static int nl80211_new_station(struct sk_buff *skb, struct genl_info *info) params.plink_action = nla_get_u8(info->attrs[NL80211_ATTR_STA_PLINK_ACTION]); + if (!rdev->ops->add_station) + return -EOPNOTSUPP; + if (parse_station_flags(info, ¶ms)) return -EINVAL; - /* parse WME attributes if sta is WME capable */ - if ((rdev->wiphy.flags & WIPHY_FLAG_AP_UAPSD) && - (params.sta_flags_set & BIT(NL80211_STA_FLAG_WME)) && - info->attrs[NL80211_ATTR_STA_WME]) { - struct nlattr *tb[NL80211_STA_WME_MAX + 1]; - struct nlattr *nla; + switch (dev->ieee80211_ptr->iftype) { + case NL80211_IFTYPE_AP: + case NL80211_IFTYPE_AP_VLAN: + case NL80211_IFTYPE_P2P_GO: + /* parse WME attributes if sta is WME capable */ + if ((rdev->wiphy.flags & WIPHY_FLAG_AP_UAPSD) && + (params.sta_flags_set & BIT(NL80211_STA_FLAG_WME)) && + info->attrs[NL80211_ATTR_STA_WME]) { + struct nlattr *tb[NL80211_STA_WME_MAX + 1]; + struct nlattr *nla; - nla = info->attrs[NL80211_ATTR_STA_WME]; - err = nla_parse_nested(tb, NL80211_STA_WME_MAX, nla, - nl80211_sta_wme_policy); - if (err) - return err; + nla = info->attrs[NL80211_ATTR_STA_WME]; + err = nla_parse_nested(tb, NL80211_STA_WME_MAX, nla, + nl80211_sta_wme_policy); + if (err) + return err; - if (tb[NL80211_STA_WME_UAPSD_QUEUES]) - params.uapsd_queues = - nla_get_u8(tb[NL80211_STA_WME_UAPSD_QUEUES]); - if (params.uapsd_queues & ~IEEE80211_WMM_IE_STA_QOSINFO_AC_MASK) + if (tb[NL80211_STA_WME_UAPSD_QUEUES]) + params.uapsd_queues = + nla_get_u8(tb[NL80211_STA_WME_UAPSD_QUEUES]); + if (params.uapsd_queues & + ~IEEE80211_WMM_IE_STA_QOSINFO_AC_MASK) + return -EINVAL; + + if (tb[NL80211_STA_WME_MAX_SP]) + params.max_sp = + nla_get_u8(tb[NL80211_STA_WME_MAX_SP]); + + if (params.max_sp & + ~IEEE80211_WMM_IE_STA_QOSINFO_SP_MASK) + return -EINVAL; + + params.sta_modify_mask |= STATION_PARAM_APPLY_UAPSD; + } + /* TDLS peers cannot be added */ + if (params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) return -EINVAL; + /* but don't bother the driver with it */ + params.sta_flags_mask &= ~BIT(NL80211_STA_FLAG_TDLS_PEER); - if (tb[NL80211_STA_WME_MAX_SP]) - params.max_sp = - nla_get_u8(tb[NL80211_STA_WME_MAX_SP]); - - if (params.max_sp & ~IEEE80211_WMM_IE_STA_QOSINFO_SP_MASK) + /* must be last in here for error handling */ + params.vlan = get_vlan(info, rdev); + if (IS_ERR(params.vlan)) + return PTR_ERR(params.vlan); + break; + case NL80211_IFTYPE_MESH_POINT: + /* TDLS peers cannot be added */ + if (params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) return -EINVAL; - - params.sta_modify_mask |= STATION_PARAM_APPLY_UAPSD; + break; + case NL80211_IFTYPE_STATION: + /* Only TDLS peers can be added */ + if (!(params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER))) + return -EINVAL; + /* Can only add if TDLS ... */ + if (!(rdev->wiphy.flags & WIPHY_FLAG_SUPPORTS_TDLS)) + return -EOPNOTSUPP; + /* ... with external setup is supported */ + if (!(rdev->wiphy.flags & WIPHY_FLAG_TDLS_EXTERNAL_SETUP)) + return -EOPNOTSUPP; + break; + default: + return -EOPNOTSUPP; } - if (dev->ieee80211_ptr->iftype != NL80211_IFTYPE_AP && - dev->ieee80211_ptr->iftype != NL80211_IFTYPE_AP_VLAN && - dev->ieee80211_ptr->iftype != NL80211_IFTYPE_MESH_POINT && - dev->ieee80211_ptr->iftype != NL80211_IFTYPE_P2P_GO && - dev->ieee80211_ptr->iftype != NL80211_IFTYPE_STATION) - return -EINVAL; - - /* - * Only managed stations can add TDLS peers, and only when the - * wiphy supports external TDLS setup. - */ - if (dev->ieee80211_ptr->iftype == NL80211_IFTYPE_STATION && - !((params.sta_flags_set & BIT(NL80211_STA_FLAG_TDLS_PEER)) && - (rdev->wiphy.flags & WIPHY_FLAG_SUPPORTS_TDLS) && - (rdev->wiphy.flags & WIPHY_FLAG_TDLS_EXTERNAL_SETUP))) - return -EINVAL; - - params.vlan = get_vlan(info, rdev); - if (IS_ERR(params.vlan)) - return PTR_ERR(params.vlan); - - /* validate settings */ - err = 0; - - if (!rdev->ops->add_station) { - err = -EOPNOTSUPP; - goto out; - } + /* be aware of params.vlan when changing code here */ err = rdev->ops->add_station(&rdev->wiphy, dev, mac_addr, ¶ms); - out: if (params.vlan) dev_put(params.vlan); return err;