hollalinux
/
linux-sg2042
mirror of https://github.com/sophgo/linux-riscv.git
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

mtd: remove bcmring NAND driver 

This driver is being removed as part of the cleanup of the bcmring
SoC from mainline as it is no longer maintained.

Signed-off-by: Christian Daudt <csd@broadcom.com>
Reviewed-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This commit is contained in:
Christian Daudt 2012-09-21 14:40:25 -07:00 committed by David Woodhouse
parent 5ca7f41528
commit b2bc415b6b
7 changed files with 0 additions and 1255 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

9
MAINTAINERS
View File

@ -665,15 +665,6 @@ L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
S: Maintained
F: arch/arm/mach-bcmring
ARM/BCMRING MTD NAND DRIVER
M: Jiandong Zheng <jdzheng@broadcom.com>
M: Scott Branden <sbranden@broadcom.com>
L: linux-mtd@lists.infradead.org
S: Maintained
F: drivers/mtd/nand/bcm_umi_nand.c
F: drivers/mtd/nand/bcm_umi_bch.c
F: drivers/mtd/nand/nand_bcm_umi.h
ARM/CALXEDA HIGHBANK ARCHITECTURE
M: Rob Herring <rob.herring@calxeda.com>
L: linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)

16
drivers/mtd/nand/Kconfig
View File

@ -258,22 +258,6 @@ config MTD_NAND_S3C2410_CLKSTOP
when the is NAND chip selected or released, but will save
approximately 5mA of power when there is nothing happening.
config MTD_NAND_BCM_UMI
tristate "NAND Flash support for BCM Reference Boards"
depends on ARCH_BCMRING
help
This enables the NAND flash controller on the BCM UMI block.
No board specific support is done by this driver, each board
must advertise a platform_device for the driver to attach.
config MTD_NAND_BCM_UMI_HWCS
bool "BCM UMI NAND Hardware CS"
depends on MTD_NAND_BCM_UMI
help
Enable the use of the BCM UMI block's internal CS using NAND.
This should only be used if you know the external NAND CS can toggle.
config MTD_NAND_DISKONCHIP
tristate "DiskOnChip 2000, Millennium and Millennium Plus (NAND reimplementation) (EXPERIMENTAL)"
depends on EXPERIMENTAL

1
drivers/mtd/nand/Makefile
View File

@ -48,7 +48,6 @@ obj-$(CONFIG_MTD_NAND_SOCRATES) += socrates_nand.o
obj-$(CONFIG_MTD_NAND_TXX9NDFMC) += txx9ndfmc.o
obj-$(CONFIG_MTD_NAND_NUC900) += nuc900_nand.o
obj-$(CONFIG_MTD_NAND_NOMADIK) += nomadik_nand.o
obj-$(CONFIG_MTD_NAND_BCM_UMI) += bcm_umi_nand.o nand_bcm_umi.o
obj-$(CONFIG_MTD_NAND_MPC5121_NFC) += mpc5121_nfc.o
obj-$(CONFIG_MTD_NAND_RICOH) += r852.o
obj-$(CONFIG_MTD_NAND_JZ4740) += jz4740_nand.o

210
drivers/mtd/nand/bcm_umi_bch.c
View File

@ -1,210 +0,0 @@
/*****************************************************************************
* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
/* ---- Include Files ---------------------------------------------------- */
#include "nand_bcm_umi.h"
/* ---- External Variable Declarations ----------------------------------- */
/* ---- External Function Prototypes ------------------------------------- */
/* ---- Public Variables ------------------------------------------------- */
/* ---- Private Constants and Types -------------------------------------- */
/* ---- Private Function Prototypes -------------------------------------- */
static int bcm_umi_bch_read_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, uint8_t *buf, int oob_required, int page);
static int bcm_umi_bch_write_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, const uint8_t *buf, int oob_required);
/* ---- Private Variables ------------------------------------------------ */
/*
** nand_hw_eccoob
** New oob placement block for use with hardware ecc generation.
*/
static struct nand_ecclayout nand_hw_eccoob_512 = {
/* Reserve 5 for BI indicator */
.oobfree = {
#if (NAND_ECC_NUM_BYTES > 3)
{.offset = 0, .length = 2}
#else
{.offset = 0, .length = 5},
{.offset = 6, .length = 7}
#endif
}
};
/*
** We treat the OOB for a 2K page as if it were 4 512 byte oobs,
** except the BI is at byte 0.
*/
static struct nand_ecclayout nand_hw_eccoob_2048 = {
/* Reserve 0 as BI indicator */
.oobfree = {
#if (NAND_ECC_NUM_BYTES > 10)
{.offset = 1, .length = 2},
#elif (NAND_ECC_NUM_BYTES > 7)
{.offset = 1, .length = 5},
{.offset = 16, .length = 6},
{.offset = 32, .length = 6},
{.offset = 48, .length = 6}
#else
{.offset = 1, .length = 8},
{.offset = 16, .length = 9},
{.offset = 32, .length = 9},
{.offset = 48, .length = 9}
#endif
}
};
/* We treat the OOB for a 4K page as if it were 8 512 byte oobs,
* except the BI is at byte 0. */
static struct nand_ecclayout nand_hw_eccoob_4096 = {
/* Reserve 0 as BI indicator */
.oobfree = {
#if (NAND_ECC_NUM_BYTES > 10)
{.offset = 1, .length = 2},
{.offset = 16, .length = 3},
{.offset = 32, .length = 3},
{.offset = 48, .length = 3},
{.offset = 64, .length = 3},
{.offset = 80, .length = 3},
{.offset = 96, .length = 3},
{.offset = 112, .length = 3}
#else
{.offset = 1, .length = 5},
{.offset = 16, .length = 6},
{.offset = 32, .length = 6},
{.offset = 48, .length = 6},
{.offset = 64, .length = 6},
{.offset = 80, .length = 6},
{.offset = 96, .length = 6},
{.offset = 112, .length = 6}
#endif
}
};
/* ---- Private Functions ------------------------------------------------ */
/* ==== Public Functions ================================================= */
/****************************************************************************
*
* bcm_umi_bch_read_page_hwecc - hardware ecc based page read function
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: buffer to store read data
* @oob_required: caller expects OOB data read to chip->oob_poi
*
***************************************************************************/
static int bcm_umi_bch_read_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, uint8_t * buf,
int oob_required, int page)
{
int sectorIdx = 0;
int eccsize = chip->ecc.size;
int eccsteps = chip->ecc.steps;
uint8_t *datap = buf;
uint8_t eccCalc[NAND_ECC_NUM_BYTES];
int sectorOobSize = mtd->oobsize / eccsteps;
int stat;
unsigned int max_bitflips = 0;
for (sectorIdx = 0; sectorIdx < eccsteps;
sectorIdx++, datap += eccsize) {
if (sectorIdx > 0) {
/* Seek to page location within sector */
chip->cmdfunc(mtd, NAND_CMD_RNDOUT, sectorIdx * eccsize,
-1);
}
/* Enable hardware ECC before reading the buf */
nand_bcm_umi_bch_enable_read_hwecc();
/* Read in data */
bcm_umi_nand_read_buf(mtd, datap, eccsize);
/* Pause hardware ECC after reading the buf */
nand_bcm_umi_bch_pause_read_ecc_calc();
/* Read the OOB ECC */
chip->cmdfunc(mtd, NAND_CMD_RNDOUT,
mtd->writesize + sectorIdx * sectorOobSize, -1);
nand_bcm_umi_bch_read_oobEcc(mtd->writesize, eccCalc,
NAND_ECC_NUM_BYTES,
chip->oob_poi +
sectorIdx * sectorOobSize);
/* Correct any ECC detected errors */
stat =
nand_bcm_umi_bch_correct_page(datap, eccCalc,
NAND_ECC_NUM_BYTES);
/* Update Stats */
if (stat < 0) {
#if defined(NAND_BCM_UMI_DEBUG)
printk(KERN_WARNING "%s uncorr_err sectorIdx=%d\n",
__func__, sectorIdx);
printk(KERN_WARNING "%s data %*ph\n",
__func__, 8, datap);
printk(KERN_WARNING "%s ecc %*ph\n",
__func__, 13, eccCalc);
BUG();
#endif
mtd->ecc_stats.failed++;
} else {
#if defined(NAND_BCM_UMI_DEBUG)
if (stat > 0) {
printk(KERN_INFO
"%s %d correctable_errors detected\n",
__func__, stat);
}
#endif
mtd->ecc_stats.corrected += stat;
max_bitflips = max_t(unsigned int, max_bitflips, stat);
}
}
return max_bitflips;
}
/****************************************************************************
*
* bcm_umi_bch_write_page_hwecc - hardware ecc based page write function
* @mtd: mtd info structure
* @chip: nand chip info structure
* @buf: data buffer
* @oob_required: must write chip->oob_poi to OOB
*
***************************************************************************/
static int bcm_umi_bch_write_page_hwecc(struct mtd_info *mtd,
struct nand_chip *chip, const uint8_t *buf, int oob_required)
{
int sectorIdx = 0;
int eccsize = chip->ecc.size;
int eccsteps = chip->ecc.steps;
const uint8_t *datap = buf;
uint8_t *oobp = chip->oob_poi;
int sectorOobSize = mtd->oobsize / eccsteps;
for (sectorIdx = 0; sectorIdx < eccsteps;
sectorIdx++, datap += eccsize, oobp += sectorOobSize) {
/* Enable hardware ECC before writing the buf */
nand_bcm_umi_bch_enable_write_hwecc();
bcm_umi_nand_write_buf(mtd, datap, eccsize);
nand_bcm_umi_bch_write_oobEcc(mtd->writesize, oobp,
NAND_ECC_NUM_BYTES);
}
bcm_umi_nand_write_buf(mtd, chip->oob_poi, mtd->oobsize);
return 0;
}

533
drivers/mtd/nand/bcm_umi_nand.c
View File

@ -1,533 +0,0 @@
/*****************************************************************************
* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
/* ---- Include Files ---------------------------------------------------- */
#include <linux/module.h>
#include <linux/types.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/ioport.h>
#include <linux/device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/io.h>
#include <linux/platform_device.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/nand_ecc.h>
#include <linux/mtd/partitions.h>
#include <asm/mach-types.h>
#include <mach/reg_nand.h>
#include <mach/reg_umi.h>
#include "nand_bcm_umi.h"
#include <mach/memory_settings.h>
#define USE_DMA 1
#include <mach/dma.h>
#include <linux/dma-mapping.h>
#include <linux/completion.h>
/* ---- External Variable Declarations ----------------------------------- */
/* ---- External Function Prototypes ------------------------------------- */
/* ---- Public Variables ------------------------------------------------- */
/* ---- Private Constants and Types -------------------------------------- */
static const __devinitconst char gBanner[] = KERN_INFO \
"BCM UMI MTD NAND Driver: 1.00\n";
#if NAND_ECC_BCH
static uint8_t scan_ff_pattern[] = { 0xff };
static struct nand_bbt_descr largepage_bbt = {
.options = 0,
.offs = 0,
.len = 1,
.pattern = scan_ff_pattern
};
#endif
/*
** Preallocate a buffer to avoid having to do this every dma operation.
** This is the size of the preallocated coherent DMA buffer.
*/
#if USE_DMA
#define DMA_MIN_BUFLEN 512
#define DMA_MAX_BUFLEN PAGE_SIZE
#define USE_DIRECT_IO(len) (((len) < DMA_MIN_BUFLEN) || \
((len) > DMA_MAX_BUFLEN))
/*
* The current NAND data space goes from 0x80001900 to 0x80001FFF,
* which is only 0x700 = 1792 bytes long. This is too small for 2K, 4K page
* size NAND flash. Need to break the DMA down to multiple 1Ks.
*
* Need to make sure REG_NAND_DATA_PADDR + DMA_MAX_LEN < 0x80002000
*/
#define DMA_MAX_LEN 1024
#else /* !USE_DMA */
#define DMA_MIN_BUFLEN 0
#define DMA_MAX_BUFLEN 0
#define USE_DIRECT_IO(len) 1
#endif
/* ---- Private Function Prototypes -------------------------------------- */
static void bcm_umi_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len);
static void bcm_umi_nand_write_buf(struct mtd_info *mtd, const u_char * buf,
int len);
/* ---- Private Variables ------------------------------------------------ */
static struct mtd_info *board_mtd;
static void __iomem *bcm_umi_io_base;
static void *virtPtr;
static dma_addr_t physPtr;
static struct completion nand_comp;
/* ---- Private Functions ------------------------------------------------ */
#if NAND_ECC_BCH
#include "bcm_umi_bch.c"
#else
#include "bcm_umi_hamming.c"
#endif
#if USE_DMA
/* Handler called when the DMA finishes. */
static void nand_dma_handler(DMA_Device_t dev, int reason, void *userData)
{
complete(&nand_comp);
}
static int nand_dma_init(void)
{
int rc;
rc = dma_set_device_handler(DMA_DEVICE_NAND_MEM_TO_MEM,
nand_dma_handler, NULL);
if (rc != 0) {
printk(KERN_ERR "dma_set_device_handler failed: %d\n", rc);
return rc;
}
virtPtr =
dma_alloc_coherent(NULL, DMA_MAX_BUFLEN, &physPtr, GFP_KERNEL);
if (virtPtr == NULL) {
printk(KERN_ERR "NAND - Failed to allocate memory for DMA buffer\n");
return -ENOMEM;
}
return 0;
}
static void nand_dma_term(void)
{
if (virtPtr != NULL)
dma_free_coherent(NULL, DMA_MAX_BUFLEN, virtPtr, physPtr);
}
static void nand_dma_read(void *buf, int len)
{
int offset = 0;
int tmp_len = 0;
int len_left = len;
DMA_Handle_t hndl;
if (virtPtr == NULL)
panic("nand_dma_read: virtPtr == NULL\n");
if ((void *)physPtr == NULL)
panic("nand_dma_read: physPtr == NULL\n");
hndl = dma_request_channel(DMA_DEVICE_NAND_MEM_TO_MEM);
if (hndl < 0) {
printk(KERN_ERR
"nand_dma_read: unable to allocate dma channel: %d\n",
(int)hndl);
panic("\n");
}
while (len_left > 0) {
if (len_left > DMA_MAX_LEN) {
tmp_len = DMA_MAX_LEN;
len_left -= DMA_MAX_LEN;
} else {
tmp_len = len_left;
len_left = 0;
}
init_completion(&nand_comp);
dma_transfer_mem_to_mem(hndl, REG_NAND_DATA_PADDR,
physPtr + offset, tmp_len);
wait_for_completion(&nand_comp);
offset += tmp_len;
}
dma_free_channel(hndl);
if (buf != NULL)
memcpy(buf, virtPtr, len);
}
static void nand_dma_write(const void *buf, int len)
{
int offset = 0;
int tmp_len = 0;
int len_left = len;
DMA_Handle_t hndl;
if (buf == NULL)
panic("nand_dma_write: buf == NULL\n");
if (virtPtr == NULL)
panic("nand_dma_write: virtPtr == NULL\n");
if ((void *)physPtr == NULL)
panic("nand_dma_write: physPtr == NULL\n");
memcpy(virtPtr, buf, len);
hndl = dma_request_channel(DMA_DEVICE_NAND_MEM_TO_MEM);
if (hndl < 0) {
printk(KERN_ERR
"nand_dma_write: unable to allocate dma channel: %d\n",
(int)hndl);
panic("\n");
}
while (len_left > 0) {
if (len_left > DMA_MAX_LEN) {
tmp_len = DMA_MAX_LEN;
len_left -= DMA_MAX_LEN;
} else {
tmp_len = len_left;
len_left = 0;
}
init_completion(&nand_comp);
dma_transfer_mem_to_mem(hndl, physPtr + offset,
REG_NAND_DATA_PADDR, tmp_len);
wait_for_completion(&nand_comp);
offset += tmp_len;
}
dma_free_channel(hndl);
}
#endif
static int nand_dev_ready(struct mtd_info *mtd)
{
return nand_bcm_umi_dev_ready();
}
/****************************************************************************
*
* bcm_umi_nand_inithw
*
* This routine does the necessary hardware (board-specific)
* initializations. This includes setting up the timings, etc.
*
***************************************************************************/
int bcm_umi_nand_inithw(void)
{
/* Configure nand timing parameters */
REG_UMI_NAND_TCR &= ~0x7ffff;
REG_UMI_NAND_TCR |= HW_CFG_NAND_TCR;
#if !defined(CONFIG_MTD_NAND_BCM_UMI_HWCS)
/* enable software control of CS */
REG_UMI_NAND_TCR |= REG_UMI_NAND_TCR_CS_SWCTRL;
#endif
/* keep NAND chip select asserted */
REG_UMI_NAND_RCSR |= REG_UMI_NAND_RCSR_CS_ASSERTED;
REG_UMI_NAND_TCR &= ~REG_UMI_NAND_TCR_WORD16;
/* enable writes to flash */
REG_UMI_MMD_ICR |= REG_UMI_MMD_ICR_FLASH_WP;
writel(NAND_CMD_RESET, bcm_umi_io_base + REG_NAND_CMD_OFFSET);
nand_bcm_umi_wait_till_ready();
#if NAND_ECC_BCH
nand_bcm_umi_bch_config_ecc(NAND_ECC_NUM_BYTES);
#endif
return 0;
}
/* Used to turn latch the proper register for access. */
static void bcm_umi_nand_hwcontrol(struct mtd_info *mtd, int cmd,
unsigned int ctrl)
{
/* send command to hardware */
struct nand_chip *chip = mtd->priv;
if (ctrl & NAND_CTRL_CHANGE) {
if (ctrl & NAND_CLE) {
chip->IO_ADDR_W = bcm_umi_io_base + REG_NAND_CMD_OFFSET;
goto CMD;
}
if (ctrl & NAND_ALE) {
chip->IO_ADDR_W =
bcm_umi_io_base + REG_NAND_ADDR_OFFSET;
goto CMD;
}
chip->IO_ADDR_W = bcm_umi_io_base + REG_NAND_DATA8_OFFSET;
}
CMD:
/* Send command to chip directly */
if (cmd != NAND_CMD_NONE)
writeb(cmd, chip->IO_ADDR_W);
}
static void bcm_umi_nand_write_buf(struct mtd_info *mtd, const u_char * buf,
int len)
{
if (USE_DIRECT_IO(len)) {
/* Do it the old way if the buffer is small or too large.
* Probably quicker than starting and checking dma. */
int i;
struct nand_chip *this = mtd->priv;
for (i = 0; i < len; i++)
writeb(buf[i], this->IO_ADDR_W);
}
#if USE_DMA
else
nand_dma_write(buf, len);
#endif
}
static void bcm_umi_nand_read_buf(struct mtd_info *mtd, u_char * buf, int len)
{
if (USE_DIRECT_IO(len)) {
int i;
struct nand_chip *this = mtd->priv;
for (i = 0; i < len; i++)
buf[i] = readb(this->IO_ADDR_R);
}
#if USE_DMA
else
nand_dma_read(buf, len);
#endif
}
static int __devinit bcm_umi_nand_probe(struct platform_device *pdev)
{
struct nand_chip *this;
struct resource *r;
int err = 0;
printk(gBanner);
/* Allocate memory for MTD device structure and private data */
board_mtd =
kmalloc(sizeof(struct mtd_info) + sizeof(struct nand_chip),
GFP_KERNEL);
if (!board_mtd) {
printk(KERN_WARNING
"Unable to allocate NAND MTD device structure.\n");
return -ENOMEM;
}
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!r) {
err = -ENXIO;
goto out_free;
}
/* map physical address */
bcm_umi_io_base = ioremap(r->start, resource_size(r));
if (!bcm_umi_io_base) {
printk(KERN_ERR "ioremap to access BCM UMI NAND chip failed\n");
err = -EIO;
goto out_free;
}
/* Get pointer to private data */
this = (struct nand_chip *)(&board_mtd[1]);
/* Initialize structures */
memset((char *)board_mtd, 0, sizeof(struct mtd_info));
memset((char *)this, 0, sizeof(struct nand_chip));
/* Link the private data with the MTD structure */
board_mtd->priv = this;
/* Initialize the NAND hardware. */
if (bcm_umi_nand_inithw() < 0) {
printk(KERN_ERR "BCM UMI NAND chip could not be initialized\n");
err = -EIO;
goto out_unmap;
}
/* Set address of NAND IO lines */
this->IO_ADDR_W = bcm_umi_io_base + REG_NAND_DATA8_OFFSET;
this->IO_ADDR_R = bcm_umi_io_base + REG_NAND_DATA8_OFFSET;
/* Set command delay time, see datasheet for correct value */
this->chip_delay = 0;
/* Assign the device ready function, if available */
this->dev_ready = nand_dev_ready;
this->options = 0;
this->write_buf = bcm_umi_nand_write_buf;
this->read_buf = bcm_umi_nand_read_buf;
this->cmd_ctrl = bcm_umi_nand_hwcontrol;
this->ecc.mode = NAND_ECC_HW;
this->ecc.size = 512;
this->ecc.bytes = NAND_ECC_NUM_BYTES;
#if NAND_ECC_BCH
this->ecc.read_page = bcm_umi_bch_read_page_hwecc;
this->ecc.write_page = bcm_umi_bch_write_page_hwecc;
#else
this->ecc.correct = nand_correct_data512;
this->ecc.calculate = bcm_umi_hamming_get_hw_ecc;
this->ecc.hwctl = bcm_umi_hamming_enable_hwecc;
#endif
#if USE_DMA
err = nand_dma_init();
if (err != 0)
goto out_unmap;
#endif
/* Figure out the size of the device that we have.
* We need to do this to figure out which ECC
* layout we'll be using.
*/
err = nand_scan_ident(board_mtd, 1, NULL);
if (err) {
printk(KERN_ERR "nand_scan failed: %d\n", err);
goto out_unmap;
}
/* Now that we know the nand size, we can setup the ECC layout */
switch (board_mtd->writesize) { /* writesize is the pagesize */
case 4096:
this->ecc.layout = &nand_hw_eccoob_4096;
break;
case 2048:
this->ecc.layout = &nand_hw_eccoob_2048;
break;
case 512:
this->ecc.layout = &nand_hw_eccoob_512;
break;
default:
{
printk(KERN_ERR "NAND - Unrecognized pagesize: %d\n",
board_mtd->writesize);
err = -EINVAL;
goto out_unmap;
}
}
#if NAND_ECC_BCH
if (board_mtd->writesize > 512) {
if (this->bbt_options & NAND_BBT_USE_FLASH)
largepage_bbt.options = NAND_BBT_SCAN2NDPAGE;
this->badblock_pattern = &largepage_bbt;
}
this->ecc.strength = 8;
#endif
/* Now finish off the scan, now that ecc.layout has been initialized. */
err = nand_scan_tail(board_mtd);
if (err) {
printk(KERN_ERR "nand_scan failed: %d\n", err);
goto out_unmap;
}
/* Register the partitions */
board_mtd->name = "bcm_umi-nand";
mtd_device_parse_register(board_mtd, NULL, NULL, NULL, 0);
/* Return happy */
return 0;
out_unmap:
iounmap(bcm_umi_io_base);
out_free:
kfree(board_mtd);
return err;
}
static int bcm_umi_nand_remove(struct platform_device *pdev)
{
#if USE_DMA
nand_dma_term();
#endif
/* Release resources, unregister device */
nand_release(board_mtd);
/* unmap physical address */
iounmap(bcm_umi_io_base);
/* Free the MTD device structure */
kfree(board_mtd);
return 0;
}
#ifdef CONFIG_PM
static int bcm_umi_nand_suspend(struct platform_device *pdev,
pm_message_t state)
{
printk(KERN_ERR "MTD NAND suspend is being called\n");
return 0;
}
static int bcm_umi_nand_resume(struct platform_device *pdev)
{
printk(KERN_ERR "MTD NAND resume is being called\n");
return 0;
}
#else
#define bcm_umi_nand_suspend NULL
#define bcm_umi_nand_resume NULL
#endif
static struct platform_driver nand_driver = {
.driver = {
.name = "bcm-nand",
.owner = THIS_MODULE,
},
.probe = bcm_umi_nand_probe,
.remove = bcm_umi_nand_remove,
.suspend = bcm_umi_nand_suspend,
.resume = bcm_umi_nand_resume,
};
module_platform_driver(nand_driver);
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Broadcom");
MODULE_DESCRIPTION("BCM UMI MTD NAND driver");

149
drivers/mtd/nand/nand_bcm_umi.c
View File

@ -1,149 +0,0 @@
/*****************************************************************************
* Copyright 2004 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
/* ---- Include Files ---------------------------------------------------- */
#include <mach/reg_umi.h>
#include "nand_bcm_umi.h"
#ifdef BOOT0_BUILD
#include <uart.h>
#endif
/* ---- External Variable Declarations ----------------------------------- */
/* ---- External Function Prototypes ------------------------------------- */
/* ---- Public Variables ------------------------------------------------- */
/* ---- Private Constants and Types -------------------------------------- */
/* ---- Private Function Prototypes -------------------------------------- */
/* ---- Private Variables ------------------------------------------------ */
/* ---- Private Functions ------------------------------------------------ */
#if NAND_ECC_BCH
/****************************************************************************
* nand_bch_ecc_flip_bit - Routine to flip an errored bit
*
* PURPOSE:
* This is a helper routine that flips the bit (0 -> 1 or 1 -> 0) of the
* errored bit specified
*
* PARAMETERS:
* datap - Container that holds the 512 byte data
* errorLocation - Location of the bit that needs to be flipped
*
* RETURNS:
* None
****************************************************************************/
static void nand_bcm_umi_bch_ecc_flip_bit(uint8_t *datap, int errorLocation)
{
int locWithinAByte = (errorLocation & REG_UMI_BCH_ERR_LOC_BYTE) >> 0;
int locWithinAWord = (errorLocation & REG_UMI_BCH_ERR_LOC_WORD) >> 3;
int locWithinAPage = (errorLocation & REG_UMI_BCH_ERR_LOC_PAGE) >> 5;
uint8_t errorByte = 0;
uint8_t byteMask = 1 << locWithinAByte;
/* BCH uses big endian, need to change the location
* bits to little endian */
locWithinAWord = 3 - locWithinAWord;
errorByte = datap[locWithinAPage * sizeof(uint32_t) + locWithinAWord];
#ifdef BOOT0_BUILD
puthexs("\nECC Correct Offset: ",
locWithinAPage * sizeof(uint32_t) + locWithinAWord);
puthexs(" errorByte:", errorByte);
puthex8(" Bit: ", locWithinAByte);
#endif
if (errorByte & byteMask) {
/* bit needs to be cleared */
errorByte &= ~byteMask;
} else {
/* bit needs to be set */
errorByte |= byteMask;
}
/* write back the value with the fixed bit */
datap[locWithinAPage * sizeof(uint32_t) + locWithinAWord] = errorByte;
}
/****************************************************************************
* nand_correct_page_bch - Routine to correct bit errors when reading NAND
*
* PURPOSE:
* This routine reads the BCH registers to determine if there are any bit
* errors during the read of the last 512 bytes of data + ECC bytes. If
* errors exists, the routine fixes it.
*
* PARAMETERS:
* datap - Container that holds the 512 byte data
*
* RETURNS:
* 0 or greater = Number of errors corrected
* (No errors are found or errors have been fixed)
* -1 = Error(s) cannot be fixed
****************************************************************************/
int nand_bcm_umi_bch_correct_page(uint8_t *datap, uint8_t *readEccData,
int numEccBytes)
{
int numErrors;
int errorLocation;
int idx;
uint32_t regValue;
/* wait for read ECC to be valid */
regValue = nand_bcm_umi_bch_poll_read_ecc_calc();
/*
* read the control status register to determine if there
* are error'ed bits
* see if errors are correctible
*/
if ((regValue & REG_UMI_BCH_CTRL_STATUS_UNCORR_ERR) > 0) {
int i;
for (i = 0; i < numEccBytes; i++) {
if (readEccData[i] != 0xff) {
/* errors cannot be fixed, return -1 */
return -1;
}
}
/* If ECC is unprogrammed then we can't correct,
* assume everything OK */
return 0;
}
if ((regValue & REG_UMI_BCH_CTRL_STATUS_CORR_ERR) == 0) {
/* no errors */
return 0;
}
/*
* Fix errored bits by doing the following:
* 1. Read the number of errors in the control and status register
* 2. Read the error location registers that corresponds to the number
* of errors reported
* 3. Invert the bit in the data
*/
numErrors = (regValue & REG_UMI_BCH_CTRL_STATUS_NB_CORR_ERROR) >> 20;
for (idx = 0; idx < numErrors; idx++) {
errorLocation =
REG_UMI_BCH_ERR_LOC_ADDR(idx) & REG_UMI_BCH_ERR_LOC_MASK;
/* Flip bit */
nand_bcm_umi_bch_ecc_flip_bit(datap, errorLocation);
}
/* Errors corrected */
return numErrors;
}
#endif

337
drivers/mtd/nand/nand_bcm_umi.h
View File

@ -1,337 +0,0 @@
/*****************************************************************************
* Copyright 2003 - 2009 Broadcom Corporation. All rights reserved.
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2, available at
* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a
* license other than the GPL, without Broadcom's express prior written
* consent.
*****************************************************************************/
#ifndef NAND_BCM_UMI_H
#define NAND_BCM_UMI_H
/* ---- Include Files ---------------------------------------------------- */
#include <mach/reg_umi.h>
#include <mach/reg_nand.h>
#include <cfg_global.h>
/* ---- Constants and Types ---------------------------------------------- */
#if (CFG_GLOBAL_CHIP_FAMILY == CFG_GLOBAL_CHIP_FAMILY_BCMRING)
#define NAND_ECC_BCH (CFG_GLOBAL_CHIP_REV > 0xA0)
#else
#define NAND_ECC_BCH 0
#endif
#define CFG_GLOBAL_NAND_ECC_BCH_NUM_BYTES 13
#if NAND_ECC_BCH
#ifdef BOOT0_BUILD
#define NAND_ECC_NUM_BYTES 13
#else
#define NAND_ECC_NUM_BYTES CFG_GLOBAL_NAND_ECC_BCH_NUM_BYTES
#endif
#else
#define NAND_ECC_NUM_BYTES 3
#endif
#define NAND_DATA_ACCESS_SIZE 512
/* ---- Variable Externs ------------------------------------------ */
/* ---- Function Prototypes --------------------------------------- */
int nand_bcm_umi_bch_correct_page(uint8_t *datap, uint8_t *readEccData,
int numEccBytes);
/* Check in device is ready */
static inline int nand_bcm_umi_dev_ready(void)
{
return REG_UMI_NAND_RCSR & REG_UMI_NAND_RCSR_RDY;
}
/* Wait until device is ready */
static inline void nand_bcm_umi_wait_till_ready(void)
{
while (nand_bcm_umi_dev_ready() == 0)
;
}
/* Enable Hamming ECC */
static inline void nand_bcm_umi_hamming_enable_hwecc(void)
{
/* disable and reset ECC, 512 byte page */
REG_UMI_NAND_ECC_CSR &= ~(REG_UMI_NAND_ECC_CSR_ECC_ENABLE |
REG_UMI_NAND_ECC_CSR_256BYTE);
/* enable ECC */
REG_UMI_NAND_ECC_CSR |= REG_UMI_NAND_ECC_CSR_ECC_ENABLE;
}
#if NAND_ECC_BCH
/* BCH ECC specifics */
#define ECC_BITS_PER_CORRECTABLE_BIT 13
/* Enable BCH Read ECC */
static inline void nand_bcm_umi_bch_enable_read_hwecc(void)
{
/* disable and reset ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID;
/* Turn on ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN;
}
/* Enable BCH Write ECC */
static inline void nand_bcm_umi_bch_enable_write_hwecc(void)
{
/* disable and reset ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID;
/* Turn on ECC */
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_WR_EN;
}
/* Config number of BCH ECC bytes */
static inline void nand_bcm_umi_bch_config_ecc(uint8_t numEccBytes)
{
uint32_t nValue;
uint32_t tValue;
uint32_t kValue;
uint32_t numBits = numEccBytes * 8;
/* disable and reset ECC */
REG_UMI_BCH_CTRL_STATUS =
REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID |
REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID;
/* Every correctible bit requires 13 ECC bits */
tValue = (uint32_t) (numBits / ECC_BITS_PER_CORRECTABLE_BIT);
/* Total data in number of bits for generating and computing BCH ECC */
nValue = (NAND_DATA_ACCESS_SIZE + numEccBytes) * 8;
/* K parameter is used internally. K = N - (T * 13) */
kValue = nValue - (tValue * ECC_BITS_PER_CORRECTABLE_BIT);
/* Write the settings */
REG_UMI_BCH_N = nValue;
REG_UMI_BCH_T = tValue;
REG_UMI_BCH_K = kValue;
}
/* Pause during ECC read calculation to skip bytes in OOB */
static inline void nand_bcm_umi_bch_pause_read_ecc_calc(void)
{
REG_UMI_BCH_CTRL_STATUS =
REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN |
REG_UMI_BCH_CTRL_STATUS_PAUSE_ECC_DEC;
}
/* Resume during ECC read calculation after skipping bytes in OOB */
static inline void nand_bcm_umi_bch_resume_read_ecc_calc(void)
{
REG_UMI_BCH_CTRL_STATUS = REG_UMI_BCH_CTRL_STATUS_ECC_RD_EN;
}
/* Poll read ECC calc to check when hardware completes */
static inline uint32_t nand_bcm_umi_bch_poll_read_ecc_calc(void)
{
uint32_t regVal;
do {
/* wait for ECC to be valid */
regVal = REG_UMI_BCH_CTRL_STATUS;
} while ((regVal & REG_UMI_BCH_CTRL_STATUS_RD_ECC_VALID) == 0);
return regVal;
}
/* Poll write ECC calc to check when hardware completes */
static inline void nand_bcm_umi_bch_poll_write_ecc_calc(void)
{
/* wait for ECC to be valid */
while ((REG_UMI_BCH_CTRL_STATUS & REG_UMI_BCH_CTRL_STATUS_WR_ECC_VALID)
== 0)
;
}
/* Read the OOB and ECC, for kernel write OOB to a buffer */
#if defined(__KERNEL__) && !defined(STANDALONE)
static inline void nand_bcm_umi_bch_read_oobEcc(uint32_t pageSize,
uint8_t *eccCalc, int numEccBytes, uint8_t *oobp)
#else
static inline void nand_bcm_umi_bch_read_oobEcc(uint32_t pageSize,
uint8_t *eccCalc, int numEccBytes)
#endif
{
int eccPos = 0;
int numToRead = 16; /* There are 16 bytes per sector in the OOB */
/* ECC is already paused when this function is called */
if (pageSize != NAND_DATA_ACCESS_SIZE) {
/* skip BI */
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp++ = REG_NAND_DATA8;
#else
REG_NAND_DATA8;
#endif
numToRead--;
}
while (numToRead > numEccBytes) {
/* skip free oob region */
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp++ = REG_NAND_DATA8;
#else
REG_NAND_DATA8;
#endif
numToRead--;
}
if (pageSize == NAND_DATA_ACCESS_SIZE) {
/* read ECC bytes before BI */
nand_bcm_umi_bch_resume_read_ecc_calc();
while (numToRead > 11) {
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp = REG_NAND_DATA8;
eccCalc[eccPos++] = *oobp;
oobp++;
#else
eccCalc[eccPos++] = REG_NAND_DATA8;
#endif
numToRead--;
}
nand_bcm_umi_bch_pause_read_ecc_calc();
if (numToRead == 11) {
/* read BI */
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp++ = REG_NAND_DATA8;
#else
REG_NAND_DATA8;
#endif
numToRead--;
}
}
/* read ECC bytes */
nand_bcm_umi_bch_resume_read_ecc_calc();
while (numToRead) {
#if defined(__KERNEL__) && !defined(STANDALONE)
*oobp = REG_NAND_DATA8;
eccCalc[eccPos++] = *oobp;
oobp++;
#else
eccCalc[eccPos++] = REG_NAND_DATA8;
#endif
numToRead--;
}
}
/* Helper function to write ECC */
static inline void NAND_BCM_UMI_ECC_WRITE(int numEccBytes, int eccBytePos,
uint8_t *oobp, uint8_t eccVal)
{
if (eccBytePos <= numEccBytes)
*oobp = eccVal;
}
/* Write OOB with ECC */
static inline void nand_bcm_umi_bch_write_oobEcc(uint32_t pageSize,
uint8_t *oobp, int numEccBytes)
{
uint32_t eccVal = 0xffffffff;
/* wait for write ECC to be valid */
nand_bcm_umi_bch_poll_write_ecc_calc();
/*
** Get the hardware ecc from the 32-bit result registers.
** Read after 512 byte accesses. Format B3B2B1B0
** where B3 = ecc3, etc.
*/
if (pageSize == NAND_DATA_ACCESS_SIZE) {
/* Now fill in the ECC bytes */
if (numEccBytes >= 13)
eccVal = REG_UMI_BCH_WR_ECC_3;
/* Usually we skip CM in oob[0,1] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 15, &oobp[0],
(eccVal >> 16) & 0xff);
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 14, &oobp[1],
(eccVal >> 8) & 0xff);
/* Write ECC in oob[2,3,4] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 13, &oobp[2],
eccVal & 0xff); /* ECC 12 */
if (numEccBytes >= 9)
eccVal = REG_UMI_BCH_WR_ECC_2;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 12, &oobp[3],
(eccVal >> 24) & 0xff); /* ECC11 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 11, &oobp[4],
(eccVal >> 16) & 0xff); /* ECC10 */
/* Always Skip BI in oob[5] */
} else {
/* Always Skip BI in oob[0] */
/* Now fill in the ECC bytes */
if (numEccBytes >= 13)
eccVal = REG_UMI_BCH_WR_ECC_3;
/* Usually skip CM in oob[1,2] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 15, &oobp[1],
(eccVal >> 16) & 0xff);
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 14, &oobp[2],
(eccVal >> 8) & 0xff);
/* Write ECC in oob[3-15] */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 13, &oobp[3],
eccVal & 0xff); /* ECC12 */
if (numEccBytes >= 9)
eccVal = REG_UMI_BCH_WR_ECC_2;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 12, &oobp[4],
(eccVal >> 24) & 0xff); /* ECC11 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 11, &oobp[5],
(eccVal >> 16) & 0xff); /* ECC10 */
}
/* Fill in the remainder of ECC locations */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 10, &oobp[6],
(eccVal >> 8) & 0xff); /* ECC9 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 9, &oobp[7],
eccVal & 0xff); /* ECC8 */
if (numEccBytes >= 5)
eccVal = REG_UMI_BCH_WR_ECC_1;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 8, &oobp[8],
(eccVal >> 24) & 0xff); /* ECC7 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 7, &oobp[9],
(eccVal >> 16) & 0xff); /* ECC6 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 6, &oobp[10],
(eccVal >> 8) & 0xff); /* ECC5 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 5, &oobp[11],
eccVal & 0xff); /* ECC4 */
if (numEccBytes >= 1)
eccVal = REG_UMI_BCH_WR_ECC_0;
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 4, &oobp[12],
(eccVal >> 24) & 0xff); /* ECC3 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 3, &oobp[13],
(eccVal >> 16) & 0xff); /* ECC2 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 2, &oobp[14],
(eccVal >> 8) & 0xff); /* ECC1 */
NAND_BCM_UMI_ECC_WRITE(numEccBytes, 1, &oobp[15],
eccVal & 0xff); /* ECC0 */
}
#endif
#endif /* NAND_BCM_UMI_H */