Documentation: devicetree: Fix double words in Doumentation/devicetree
This patch fix multiple words such as "the the" and "which which" in Documentation/devicetree. Signed-off-by: Masanari Iida <standby24x7@gmail.com> Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This commit is contained in:
Masanari Iida
Jonathan Corbet
parent
633708a4a4
commit
ac3e8ea1d3
|
|
@ -8,7 +8,7 @@ Properties:
|
|||
"qcom,kpss-timer" - krait subsystem
|
||||
"qcom,scss-timer" - scorpion subsystem
|
||||
|
||||
- interrupts : Interrupts for the the debug timer, the first general purpose
|
||||
- interrupts : Interrupts for the debug timer, the first general purpose
|
||||
timer, and optionally a second general purpose timer in that
|
||||
order.
|
||||
|
||||
|
|
|
|||
|
|
@ -9,7 +9,7 @@ Properties:
|
|||
|
||||
Compatibility with many Cavium evaluation boards.
|
||||
|
||||
- reg: The base address of the the CF chip select banks. Depending on
|
||||
- reg: The base address of the CF chip select banks. Depending on
|
||||
the device configuration, there may be one or two banks.
|
||||
|
||||
- cavium,bus-width: The width of the connection to the CF devices. Valid
|
||||
|
|
|
|||
|
|
@ -12,7 +12,7 @@ configuration register for writes. These configuration register may be used to
|
|||
enable (and disable in some cases) SoC pin drivers, select peripheral clock
|
||||
sources (internal or pin), etc. In some cases, a configuration register is
|
||||
write once or the individual bits are write once. In addition to device config,
|
||||
the DSCR block may provide registers which which are used to reset peripherals,
|
||||
the DSCR block may provide registers which are used to reset peripherals,
|
||||
provide device ID information, provide ethernet MAC addresses, as well as other
|
||||
miscellaneous functions.
|
||||
|
||||
|
|
|
|||
|
|
@ -1,6 +1,6 @@
|
|||
* Renesas R-Car DMA Controller Device Tree bindings
|
||||
|
||||
Renesas R-Car Generation 2 SoCs have have multiple multi-channel DMA
|
||||
Renesas R-Car Generation 2 SoCs have multiple multi-channel DMA
|
||||
controller instances named DMAC capable of serving multiple clients. Channels
|
||||
can be dedicated to specific clients or shared between a large number of
|
||||
clients.
|
||||
|
|
|
|||
|
|
@ -39,7 +39,7 @@ Optional Properties:
|
|||
- lines-initial-states: Bitmask that specifies the initial state of each
|
||||
line. When a bit is set to zero, the corresponding line will be initialized to
|
||||
the input (pulled-up) state. When the bit is set to one, the line will be
|
||||
initialized the the low-level output state. If the property is not specified
|
||||
initialized the low-level output state. If the property is not specified
|
||||
all lines will be initialized to the input state.
|
||||
|
||||
The I/O expander can detect input state changes, and thus optionally act as
|
||||
|
|
|
|||
|
|
@ -59,7 +59,7 @@ Optional properties:
|
|||
Each child node represents one channel and has the following
|
||||
properties:
|
||||
Required properties:
|
||||
* reg: Pair of pins the the channel is connected to.
|
||||
* reg: Pair of pins the channel is connected to.
|
||||
0: VP/VN
|
||||
1: VAUXP[0]/VAUXN[0]
|
||||
2: VAUXP[1]/VAUXN[1]
|
||||
|
|
|
|||
|
|
@ -9,7 +9,7 @@ Required properties:
|
|||
Optional properties:
|
||||
- bank-width : Width (in bytes) of the device. If not present, the width
|
||||
defaults to 1 byte
|
||||
- nand-skip-bbtscan: Indicates the the BBT scanning should be skipped
|
||||
- nand-skip-bbtscan: Indicates the BBT scanning should be skipped
|
||||
- timings: array of 6 bytes for NAND timings. The meanings of these bytes
|
||||
are:
|
||||
byte 0 TCLR : CLE to RE delay in number of AHB clock cycles, only 4 bits
|
||||
|
|
|
|||
|
|
@ -3,7 +3,7 @@
|
|||
Required properties:
|
||||
- compatible: should be one of "brcm,systemport-v1.00" or "brcm,systemport"
|
||||
- reg: address and length of the register set for the device.
|
||||
- interrupts: interrupts for the device, first cell must be for the the rx
|
||||
- interrupts: interrupts for the device, first cell must be for the rx
|
||||
interrupts, and the second cell should be for the transmit queues. An
|
||||
optional third interrupt cell for Wake-on-LAN can be specified
|
||||
- local-mac-address: Ethernet MAC address (48 bits) of this adapter
|
||||
|
|
|
|||
|
|
@ -37,7 +37,7 @@ Required properties:
|
|||
|
||||
|
||||
You specify supplies using the standard regulator bindings by including
|
||||
a phandle the the relevant regulator. All specified supplies must be able
|
||||
a phandle the relevant regulator. All specified supplies must be able
|
||||
to report their voltage. The IO Voltage Domain for any non-specified
|
||||
supplies will be not be touched.
|
||||
|
||||
|
|
|
|||
|
|
@ -10,7 +10,7 @@ How overlays work
|
|||
-----------------
|
||||
|
||||
A Device Tree's overlay purpose is to modify the kernel's live tree, and
|
||||
have the modification affecting the state of the the kernel in a way that
|
||||
have the modification affecting the state of the kernel in a way that
|
||||
is reflecting the changes.
|
||||
Since the kernel mainly deals with devices, any new device node that result
|
||||
in an active device should have it created while if the device node is either
|
||||
|
|
@ -80,7 +80,7 @@ result in foo+bar.dts
|
|||
};
|
||||
---- foo+bar.dts -------------------------------------------------------------
|
||||
|
||||
As a result of the the overlay, a new device node (bar) has been created
|
||||
As a result of the overlay, a new device node (bar) has been created
|
||||
so a bar platform device will be registered and if a matching device driver
|
||||
is loaded the device will be created as expected.
|
||||
|
||||
|
|
|
|||
Loading…
Reference in New Issue