diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 253dc96ca299..5bd08e9cf2ad 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -571,6 +571,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-sl50.dtb \ am335x-wega-rdk.dtb dtb-$(CONFIG_ARCH_OMAP4) += \ + omap4-droid4-xt894.dtb \ omap4-duovero-parlor.dtb \ omap4-kc1.dtb \ omap4-panda.dtb \ @@ -600,7 +601,8 @@ dtb-$(CONFIG_SOC_DRA7XX) += \ am572x-idk.dtb \ dra7-evm.dtb \ dra72-evm.dtb \ - dra72-evm-revc.dtb + dra72-evm-revc.dtb \ + dra71-evm.dtb dtb-$(CONFIG_ARCH_ORION5X) += \ orion5x-kuroboxpro.dtb \ orion5x-lacie-d2-network.dtb \ diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/am335x-baltos-ir5221.dts index d0faa7b8c5da..f599350dd305 100644 --- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts +++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts @@ -114,7 +114,7 @@ &usb1 { status = "okay"; - dr_mode = "otg"; + dr_mode = "host"; }; &cpsw_emac0 { diff --git a/arch/arm/boot/dts/am335x-baltos.dtsi b/arch/arm/boot/dts/am335x-baltos.dtsi index dd45d172a892..09b954154e6b 100644 --- a/arch/arm/boot/dts/am335x-baltos.dtsi +++ b/arch/arm/boot/dts/am335x-baltos.dtsi @@ -406,3 +406,7 @@ &gpio0 { ti,no-reset-on-init; }; + +&gpio3 { + ti,no-reset-on-init; +}; diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi index 007b5e5a51a9..dc561d505bbe 100644 --- a/arch/arm/boot/dts/am335x-bone-common.dtsi +++ b/arch/arm/boot/dts/am335x-bone-common.dtsi @@ -6,6 +6,8 @@ * published by the Free Software Foundation. */ +#include + / { cpus { cpu@0 { @@ -310,8 +312,23 @@ * by the hardware problems. (Tip: double-check by performing a current * measurement after shutdown: it should be less than 1 mA.) */ + + interrupts = <7>; /* NMI */ + interrupt-parent = <&intc>; + ti,pmic-shutdown-controller; + charger { + interrupts = , ; + interrupts-names = "AC", "USB"; + status = "okay"; + }; + + pwrbutton { + interrupts = ; + status = "okay"; + }; + regulators { dcdc1_reg: regulator@0 { regulator-name = "vdds_dpr"; @@ -393,3 +410,8 @@ &sham { status = "okay"; }; + +&rtc { + clocks = <&clk_32768_ck>, <&clkdiv32k_ick>; + clock-names = "ext-clk", "int-clk"; +}; diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index e82432c79f85..c2186ec2834b 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -783,3 +783,8 @@ pinctrl-names = "default"; pinctrl-0 = <&dcan1_pins_default>; }; + +&rtc { + clocks = <&clk_32768_ck>, <&clkdiv32k_ick>; + clock-names = "ext-clk", "int-clk"; +}; diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 975c36e332a2..e2548d1ce753 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -715,3 +715,8 @@ blue-and-red-wiring = "crossed"; }; + +&rtc { + clocks = <&clk_32768_ck>, <&clkdiv32k_ick>; + clock-names = "ext-clk", "int-clk"; +}; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 3a3fde1f84c7..64c8aa9057a3 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -507,6 +507,8 @@ interrupts = <75 76>; ti,hwmods = "rtc"; + clocks = <&clkdiv32k_ick>; + clock-names = "int-clk"; }; spi0: spi@48030000 { @@ -857,6 +859,8 @@ interrupts = <16>; ti,hwmods = "adc_tsc"; status = "disabled"; + dmas = <&edma 53 0>, <&edma 57 0>; + dma-names = "fifo0", "fifo1"; tsc { compatible = "ti,am3359-tsc"; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 7b5ca1bbc6a9..ac55f93fc91e 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -872,6 +872,8 @@ clocks = <&adc_tsc_fck>; clock-names = "fck"; status = "disabled"; + dmas = <&edma 53 0>, <&edma 57 0>; + dma-names = "fifo0", "fifo1"; tsc { compatible = "ti,am3359-tsc"; diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts new file mode 100644 index 000000000000..2b9a5a8d69ad --- /dev/null +++ b/arch/arm/boot/dts/dra71-evm.dts @@ -0,0 +1,230 @@ +/* + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "dra72-evm-common.dtsi" +#include + +/ { + compatible = "ti,dra718-evm", "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7"; + model = "TI DRA718 EVM"; + + memory { + device_type = "memory"; + reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */ + }; + + vpo_sd_1v8_3v3: gpio-regulator-TPS74801 { + compatible = "regulator-gpio"; + + regulator-name = "vddshv8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + vin-supply = <&evm_5v0>; + + gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>; + states = <1800000 0x0 + 3000000 0x1>; + }; + + poweroff: gpio-poweroff { + compatible = "gpio-poweroff"; + gpios = <&gpio7 30 GPIO_ACTIVE_HIGH>; + input; + }; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + lp8733: lp8733@60 { + compatible = "ti,lp8733"; + reg = <0x60>; + + buck0-in-supply =<&vsys_3v3>; + buck1-in-supply =<&vsys_3v3>; + ldo0-in-supply =<&evm_5v0>; + ldo1-in-supply =<&evm_5v0>; + + lp8733_regulators: regulators { + lp8733_buck0_reg: buck0 { + /* FB_B0 -> LP8733-BUCK1 - VPO_S1_AVS - VDD_CORE_AVS (core, mpu, gpu) */ + regulator-name = "lp8733-buck0"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + lp8733_buck1_reg: buck1 { + /* FB_B1 -> LP8733-BUCK2 - VPO_S2_AVS - VDD_DSP_AVS (DSP/eve/iva) */ + regulator-name = "lp8733-buck1"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8733_ldo0_reg: ldo0 { + /* LDO0 -> LP8733-LDO1 - VPO_L1_3V3 - VDDSHV8 (optional) */ + regulator-name = "lp8733-ldo0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lp8733_ldo1_reg: ldo1 { + /* LDO1 -> LP8733-LDO2 - VPO_L2_3V3 - VDDA_USB3V3 */ + regulator-name = "lp8733-ldo1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + + lp8732: lp8732@61 { + compatible = "ti,lp8732"; + reg = <0x61>; + + buck0-in-supply =<&vsys_3v3>; + buck1-in-supply =<&vsys_3v3>; + ldo0-in-supply =<&vsys_3v3>; + ldo1-in-supply =<&vsys_3v3>; + + lp8732_regulators: regulators { + lp8732_buck0_reg: buck0 { + /* FB_B0 -> LP8732-BUCK1 - VPO_S3_1V8 - VDDS_1V8 */ + regulator-name = "lp8732-buck0"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + lp8732_buck1_reg: buck1 { + /* FB_B1 -> LP8732-BUCK2 - VPO_S4_DDR - VDD_DDR_1V35 */ + regulator-name = "lp8732-buck1"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8732_ldo0_reg: ldo0 { + /* LDO0 -> LP8732-LDO1 - VPO_L3_1V8 - VDA_1V8_PLL */ + regulator-name = "lp8732-ldo0"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + lp8732_ldo1_reg: ldo1 { + /* LDO1 -> LP8732-LDO2 - VPO_L4_1V8 - VDA_1V8_PHY */ + regulator-name = "lp8732-ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; +}; + +&pcf_gpio_21 { + interrupt-parent = <&gpio7>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; +}; + +&pcf_hdmi { + p0 { + /* + * PM_OEn to High: Disable routing I2C3 to PM_I2C + * With this PM_SEL(p3) should not matter + */ + gpio-hog; + gpios = <0 GPIO_ACTIVE_LOW>; + output-high; + line-name = "pm_oe_n"; + }; +}; + +&mmc1 { + vmmc_aux-supply = <&vpo_sd_1v8_3v3>; +}; + +&mac { + mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>, + <&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */ + <&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */ + dual_emac; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <2>; + phy-mode = "rgmii-id"; + dual_emac_res_vlan = <1>; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <3>; + phy-mode = "rgmii-id"; + dual_emac_res_vlan = <2>; +}; + +&davinci_mdio { + dp83867_0: ethernet-phy@2 { + reg = <2>; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + ti,fifo-depth = ; + ti,impedance-control = <0x1f>; + }; + + dp83867_1: ethernet-phy@3 { + reg = <3>; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + ti,fifo-depth = ; + ti,impedance-control = <0x1f>; + }; +}; + +/* No Sata on this device */ +&sata_phy { + status = "disabled"; +}; + +&sata { + status = "disabled"; +}; + +/* No RTC on this device */ +&rtc { + status = "disabled"; +}; + +&usb2_phy1 { + phy-supply = <&lp8733_ldo1_reg>; +}; + +&usb2_phy2 { + phy-supply = <&lp8733_ldo1_reg>; +}; + +&dss { + /* Supplied by VDA_1V8_PLL */ + vdda_video-supply = <&lp8732_ldo0_reg>; +}; + +&hdmi { + /* Supplied by VDA_1V8_PHY */ + vdda_video-supply = <&lp8732_ldo1_reg>; +}; diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi index c94d8d64710d..e50fbeea96e0 100644 --- a/arch/arm/boot/dts/dra72-evm-common.dtsi +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi @@ -18,11 +18,49 @@ display0 = &hdmi0; }; + evm_12v0: fixedregulator-evm12v0 { + /* main supply */ + compatible = "regulator-fixed"; + regulator-name = "evm_12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + regulator-boot-on; + }; + + evm_5v0: fixedregulator-evm5v0 { + /* Output 1 of TPS43351QDAPRQ1 on dra72-evm */ + /* Output 1 of LM5140QRWGTQ1 on dra71-evm */ + compatible = "regulator-fixed"; + regulator-name = "evm_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + + vsys_3v3: fixedregulator-vsys3v3 { + /* Output 2 of TPS43351QDAPRQ1 on dra72-evm */ + /* Output 2 of LM5140QRWGTQ1 on dra71-evm */ + compatible = "regulator-fixed"; + regulator-name = "vsys_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&evm_12v0>; + regulator-always-on; + regulator-boot-on; + }; + evm_3v3_sw: fixedregulator-evm_3v3 { + /* TPS22965DSG */ compatible = "regulator-fixed"; regulator-name = "evm_3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + vin-supply = <&vsys_3v3>; + regulator-always-on; + regulator-boot-on; }; aic_dvdd: fixedregulator-aic_dvdd { @@ -39,6 +77,7 @@ regulator-name = "evm_3v3_sd"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + vin-supply = <&evm_3v3_sw>; enable-active-high; gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>; }; @@ -69,9 +108,6 @@ tpd12s015: encoder { compatible = "ti,tpd12s015"; - pinctrl-names = "default"; - pinctrl-0 = <&tpd12s015_pins>; - gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */ <&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */ <&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */ @@ -134,72 +170,6 @@ }; &dra7_pmx_core { - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ - DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - i2c5_pins: pinmux_i2c5_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */ - DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */ - >; - }; - - nand_default: nand_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */ - DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */ - DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */ - DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */ - DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */ - DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */ - DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */ - DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */ - DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */ - DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */ - DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */ - DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */ - DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */ - DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */ - DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */ - DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */ - DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */ - DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */ - DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */ - DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */ - DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */ - DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */ - >; - }; - - usb1_pins: pinmux_usb1_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */ - >; - }; - - usb2_pins: pinmux_usb2_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */ - >; - }; - - tps65917_pins_default: tps65917_pins_default { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */ - >; - }; - mmc1_pins_default: mmc1_pins_default { pinctrl-single,pins = < DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */ @@ -240,161 +210,12 @@ DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */ >; }; - - hdmi_pins: pinmux_hdmi_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */ - DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */ - >; - }; - - tpd12s015_pins: pinmux_tpd12s015_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */ - >; - }; - - atl_pins: pinmux_atl_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */ - DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */ - >; - }; - - mcasp3_pins: pinmux_mcasp3_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */ - DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */ - DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */ - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */ - >; - }; - - mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15) - >; - }; }; &i2c1 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c1_pins>; clock-frequency = <400000>; - tps65917: tps65917@58 { - compatible = "ti,tps65917"; - reg = <0x58>; - - pinctrl-names = "default"; - pinctrl-0 = <&tps65917_pins_default>; - - interrupts = ; /* IRQ_SYS_1N */ - interrupt-controller; - #interrupt-cells = <2>; - - ti,system-power-controller; - - tps65917_pmic { - compatible = "ti,tps65917-pmic"; - - tps65917_regulators: regulators { - smps1_reg: smps1 { - /* VDD_MPU */ - regulator-name = "smps1"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1250000>; - regulator-always-on; - regulator-boot-on; - }; - - smps2_reg: smps2 { - /* VDD_CORE */ - regulator-name = "smps2"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1150000>; - regulator-boot-on; - regulator-always-on; - }; - - smps3_reg: smps3 { - /* VDD_GPU IVA DSPEVE */ - regulator-name = "smps3"; - regulator-min-microvolt = <850000>; - regulator-max-microvolt = <1250000>; - regulator-boot-on; - regulator-always-on; - }; - - smps4_reg: smps4 { - /* VDDS1V8 */ - regulator-name = "smps4"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - smps5_reg: smps5 { - /* VDD_DDR */ - regulator-name = "smps5"; - regulator-min-microvolt = <1350000>; - regulator-max-microvolt = <1350000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo1_reg: ldo1 { - /* LDO1_OUT --> SDIO */ - regulator-name = "ldo1"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - regulator-allow-bypass; - }; - - ldo3_reg: ldo3 { - /* VDDA_1V8_PHY */ - regulator-name = "ldo3"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-boot-on; - regulator-always-on; - }; - - ldo5_reg: ldo5 { - /* VDDA_1V8_PLL */ - regulator-name = "ldo5"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo4_reg: ldo4 { - /* VDDA_3V_USB: VDDA_USBHS33 */ - regulator-name = "ldo4"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-boot-on; - }; - }; - }; - - tps65917_power_button { - compatible = "ti,palmas-pwrbutton"; - interrupt-parent = <&tps65917>; - interrupts = <1 IRQ_TYPE_NONE>; - wakeup-source; - ti,palmas-long-press-seconds = <6>; - }; - }; - pcf_gpio_21: gpio@21 { compatible = "ti,pcf8575", "nxp,pcf8575"; reg = <0x21>; @@ -423,8 +244,6 @@ &i2c5 { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&i2c5_pins>; clock-frequency = <400000>; pcf_hdmi: pcf8575@26 { @@ -462,8 +281,6 @@ &gpmc { status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&nand_default>; ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */ nand@0,0 { /* To use NAND, DIP switch SW5 must be set like so: @@ -548,14 +365,6 @@ }; }; -&usb2_phy1 { - phy-supply = <&ldo4_reg>; -}; - -&usb2_phy2 { - phy-supply = <&ldo4_reg>; -}; - &omap_dwc3_1 { extcon = <&extcon_usb1>; }; @@ -566,14 +375,10 @@ &usb1 { dr_mode = "peripheral"; - pinctrl-names = "default"; - pinctrl-0 = <&usb1_pins>; }; &usb2 { dr_mode = "host"; - pinctrl-names = "default"; - pinctrl-0 = <&usb2_pins>; }; &mmc1 { @@ -581,7 +386,6 @@ pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins_default>; vmmc-supply = <&evm_3v3_sd>; - vmmc_aux-supply = <&ldo1_reg>; bus-width = <4>; /* * SDCD signal is not being used here - using the fact that GPIO mode @@ -603,71 +407,8 @@ max-frequency = <192000000>; }; -&dra7_pmx_core { - cpsw_default: cpsw_default { - pinctrl-single,pins = < - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */ - DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */ - DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */ - DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */ - DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */ - DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */ - DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */ - DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */ - DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */ - DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */ - DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */ - DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */ - >; - - }; - - cpsw_sleep: cpsw_sleep { - pinctrl-single,pins = < - /* Slave 2 */ - DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15) - >; - }; - - davinci_mdio_default: davinci_mdio_default { - pinctrl-single,pins = < - /* MDIO */ - DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */ - DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ - >; - }; - - davinci_mdio_sleep: davinci_mdio_sleep { - pinctrl-single,pins = < - DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15) - DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15) - >; - }; -}; - &mac { status = "okay"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&cpsw_default>; - pinctrl-1 = <&cpsw_sleep>; -}; - -&davinci_mdio { - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&davinci_mdio_default>; - pinctrl-1 = <&davinci_mdio_sleep>; }; &dcan1 { @@ -741,16 +482,11 @@ &dss { status = "ok"; - - vdda_video-supply = <&ldo5_reg>; }; &hdmi { status = "ok"; - pinctrl-names = "default"; - pinctrl-0 = <&hdmi_pins>; - port { hdmi_out: endpoint { remote-endpoint = <&tpd12s015_in>; @@ -759,9 +495,6 @@ }; &atl { - pinctrl-names = "default"; - pinctrl-0 = <&atl_pins>; - assigned-clocks = <&abe_dpll_sys_clk_mux>, <&atl_gfclk_mux>, <&dpll_abe_ck>, @@ -780,9 +513,6 @@ &mcasp3 { #sound-dai-cells = <0>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&mcasp3_pins>; - pinctrl-1 = <&mcasp3_sleep_pins>; assigned-clocks = <&mcasp3_ahclkx_mux>; assigned-clock-parents = <&atl_clkin2_ck>; diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts index 064b322a7a04..4ea2a0c7819e 100644 --- a/arch/arm/boot/dts/dra72-evm-revc.dts +++ b/arch/arm/boot/dts/dra72-evm-revc.dts @@ -17,17 +17,22 @@ }; }; -&tps65917_regulators { - ldo2_reg: ldo2 { - /* LDO2_OUT --> VDDA_1V8_PHY2 */ - regulator-name = "ldo2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; +&i2c1 { + tps65917: tps65917@58 { + reg = <0x58>; + + interrupts = ; /* IRQ_SYS_1N */ }; }; +#include "dra72-evm-tps65917.dtsi" + +&ldo2_reg { + /* LDO2_OUT --> VDDA_1V8_PHY2 */ + regulator-always-on; + regulator-boot-on; +}; + &hdmi { vdda-supply = <&ldo2_reg>; }; diff --git a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi new file mode 100644 index 000000000000..ee6dac44edf1 --- /dev/null +++ b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi @@ -0,0 +1,134 @@ +/* + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/tps65917-q1.pdf + */ + +&tps65917 { + compatible = "ti,tps65917"; + + interrupt-controller; + #interrupt-cells = <2>; + + ti,system-power-controller; + + tps65917_pmic { + compatible = "ti,tps65917-pmic"; + + smps1-in-supply = <&vsys_3v3>; + smps2-in-supply = <&vsys_3v3>; + smps3-in-supply = <&vsys_3v3>; + smps4-in-supply = <&vsys_3v3>; + smps5-in-supply = <&vsys_3v3>; + ldo1-in-supply = <&vsys_3v3>; + ldo2-in-supply = <&vsys_3v3>; + ldo3-in-supply = <&vsys_3v3>; + ldo4-in-supply = <&evm_5v0>; + ldo5-in-supply = <&vsys_3v3>; + + tps65917_regulators: regulators { + smps1_reg: smps1 { + /* VDD_MPU */ + regulator-name = "smps1"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + smps2_reg: smps2 { + /* VDD_CORE */ + regulator-name = "smps2"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + smps3_reg: smps3 { + /* VDD_GPU IVA DSPEVE */ + regulator-name = "smps3"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1250000>; + regulator-boot-on; + regulator-always-on; + }; + + smps4_reg: smps4 { + /* VDDS1V8 */ + regulator-name = "smps4"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps5_reg: smps5 { + /* VDD_DDR */ + regulator-name = "smps5"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + /* LDO1_OUT --> SDIO */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + regulator-allow-bypass; + }; + + ldo2_reg: ldo2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-bypass; + }; + + ldo3_reg: ldo3 { + /* VDDA_1V8_PHY */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5_reg: ldo5 { + /* VDDA_1V8_PLL */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldo4"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + }; + }; + + tps65917_power_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&tps65917>; + interrupts = <1 IRQ_TYPE_NONE>; + wakeup-source; + ti,palmas-long-press-seconds = <6>; + }; +}; diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts index e3a9b6985693..cd9c4ff12654 100644 --- a/arch/arm/boot/dts/dra72-evm.dts +++ b/arch/arm/boot/dts/dra72-evm.dts @@ -15,16 +15,16 @@ }; }; -&tps65917_regulators { - ldo2_reg: ldo2 { - /* LDO2_OUT --> TP1017 (UNUSED) */ - regulator-name = "ldo2"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-allow-bypass; +&i2c1 { + tps65917: tps65917@58 { + reg = <0x58>; + + interrupts = ; /* IRQ_SYS_1N */ }; }; +#include "dra72-evm-tps65917.dtsi" + &hdmi { vdda-supply = <&ldo3_reg>; }; diff --git a/arch/arm/boot/dts/omap4-droid4-xt894.dts b/arch/arm/boot/dts/omap4-droid4-xt894.dts new file mode 100644 index 000000000000..f3ccb4ceed9e --- /dev/null +++ b/arch/arm/boot/dts/omap4-droid4-xt894.dts @@ -0,0 +1,188 @@ +/* + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap443x.dtsi" + +/ { + model = "Motorola Droid 4 XT894"; + compatible = "motorola,droid4", "ti,omap4430", "ti,omap4"; + + chosen { + stdout-path = &uart3; + }; + + /* + * We seem to have only 1021 MB accessible, 1021 - 1022 is locked, + * then 1023 - 1024 seems to contain mbm. For SRAM, see the notes + * below about SRAM and L3_ICLK2 being unused by default, + */ + memory { + device_type = "memory"; + reg = <0x80000000 0x3fd00000>; /* 1021 MB */ + }; + + /* CPCAP really supports 1650000 to 3400000 range */ + vmmc: regulator-mmc { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + /* CPCAP really supports 3000000 to 3100000 range */ + vemmc: regulator-emmc { + compatible = "regulator-fixed"; + regulator-name = "vemmc"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + /* CPCAP really supports 1650000 to 1950000 range */ + wl12xx_vmmc: regulator-wl12xx { + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <1650000>; + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; /* gpio94 */ + startup-delay-us = <70000>; + enable-active-high; + }; +}; + +/* L3_2 interconnect is unused, SRAM, GPMC and L3_ICLK2 disabled */ +&gpmc { + status = "disabled"; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; + bus-width = <4>; + cd-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>; /* gpio106 */ +}; + +&mmc2 { + vmmc-supply = <&vemmc>; + bus-width = <8>; + non-removable; +}; + +&mmc3 { + vmmc-supply = <&wl12xx_vmmc>; + interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH + &omap4_pmx_core 0xde>; + + non-removable; + bus-width = <4>; + cap-power-off-card; + + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1283"; + reg = <2>; + interrupt-parent = <&gpio4>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; /* gpio100 */ + ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; + }; +}; + +/* L3_2 interconnect is unused, SRAM, GPMC and L3_ICLK2 disabled */ +&ocmcram { + status = "disabled"; +}; + +&omap4_pmx_core { + usb_gpio_mux_sel1: pinmux_usb_gpio_mux_sel1_pins { + /* gpio_60 */ + pinctrl-single,pins = < + OMAP4_IOPAD(0x088, PIN_OUTPUT | MUX_MODE3) + >; + }; + + usb_ulpi_pins: pinmux_usb_ulpi_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x196, MUX_MODE7) + OMAP4_IOPAD(0x198, MUX_MODE7) + OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE0) + OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE0) + >; + }; + + /* usb0_otg_dp and usb0_otg_dm */ + usb_utmi_pins: pinmux_usb_utmi_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x196, PIN_INPUT | MUX_MODE0) + OMAP4_IOPAD(0x198, PIN_INPUT | MUX_MODE0) + OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1ba, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1bc, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) + >; + }; + + /* uart3_tx_irtx and uart3_rx_irrx */ + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP4_IOPAD(0x196, MUX_MODE7) + OMAP4_IOPAD(0x198, MUX_MODE7) + OMAP4_IOPAD(0x1b2, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1b6, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1b8, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1ba, MUX_MODE2) + OMAP4_IOPAD(0x1bc, PIN_INPUT | MUX_MODE2) + OMAP4_IOPAD(0x1be, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c0, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c2, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c4, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c6, PIN_INPUT_PULLUP | MUX_MODE7) + OMAP4_IOPAD(0x1c8, PIN_INPUT_PULLUP | MUX_MODE7) + >; + }; +}; + +&omap4_pmx_wkup { + usb_gpio_mux_sel2: pinmux_usb_gpio_mux_sel2_pins { + /* gpio_wk0 */ + pinctrl-single,pins = < + OMAP4_IOPAD(0x040, PIN_OUTPUT_PULLDOWN | MUX_MODE3) + >; + }; +}; + +&uart3 { + interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH + &omap4_pmx_core 0x17c>; +}; + +/* Internal UTMI+ PHY used for OTG, CPCAP ULPI PHY for detection and charger */ +&usb_otg_hs { + interface-type = <1>; + mode = <3>; + power = <50>; +}; diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 53d31a87b44b..2fcdc516da45 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -27,12 +27,98 @@ default-state = "off"; }; }; + + evm_keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&evm_keys_pins>; + + #address-cells = <7>; + #size-cells = <0>; + + btn1 { + label = "BTN1"; + linux,code = <169>; + gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 */ + gpio-key,wakeup; + autorepeat; + debounce_interval = <50>; + }; + }; + + evm_leds { + compatible = "gpio-leds"; + + led1 { + label = "omap5:red:led"; + gpios = <&gpio9 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + led2 { + label = "omap5:green:led"; + gpios = <&gpio9 18 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + led3 { + label = "omap5:blue:led"; + gpios = <&gpio9 19 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc2"; + default-state = "off"; + }; + + led4 { + label = "omap5:green:led1"; + gpios = <&gpio9 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led5 { + label = "omap5:green:led2"; + gpios = <&gpio9 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + default-state = "off"; + }; + + led6 { + label = "omap5:green:led3"; + gpios = <&gpio9 4 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + led7 { + label = "omap5:green:led4"; + gpios = <&gpio9 5 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "default-on"; + default-state = "off"; + }; + + led8 { + label = "omap5:green:led5"; + gpios = <&gpio9 6 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; }; &hdmi { vdda-supply = <&ldo4_reg>; }; +&i2c1 { + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; +}; + &i2c5 { pinctrl-names = "default"; pinctrl-0 = <&i2c5_pins>; @@ -48,6 +134,12 @@ }; &omap5_pmx_core { + evm_keys_pins: pinmux_evm_keys_gpio_pins { + pinctrl-single,pins = < + OMAP5_IOPAD(0x0b6, PIN_INPUT | MUX_MODE6) /* gpio3_83 */ + >; + }; + i2c5_pins: pinmux_i2c5_pins { pinctrl-single,pins = < OMAP5_IOPAD(0x1c6, PIN_INPUT | MUX_MODE0) /* i2c5_scl */ diff --git a/arch/arm/boot/dts/tps65217.dtsi b/arch/arm/boot/dts/tps65217.dtsi index a63272422d76..02de56b55823 100644 --- a/arch/arm/boot/dts/tps65217.dtsi +++ b/arch/arm/boot/dts/tps65217.dtsi @@ -13,6 +13,18 @@ &tps { compatible = "ti,tps65217"; + interrupt-controller; + #interrupt-cells = <1>; + + charger { + compatible = "ti,tps65217-charger"; + status = "disabled"; + }; + + pwrbutton { + compatible = "ti,tps65217-pwrbutton"; + status = "disabled"; + }; regulators { #address-cells = <1>; diff --git a/include/dt-bindings/mfd/tps65217.h b/include/dt-bindings/mfd/tps65217.h new file mode 100644 index 000000000000..cafb9e60cf12 --- /dev/null +++ b/include/dt-bindings/mfd/tps65217.h @@ -0,0 +1,26 @@ +/* + * This header provides macros for TI TPS65217 DT bindings. + * + * Copyright (C) 2016 Texas Instruments + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License along with + * this program. If not, see . + */ + +#ifndef __DT_BINDINGS_TPS65217_H__ +#define __DT_BINDINGS_TPS65217_H__ + +#define TPS65217_IRQ_USB 0 +#define TPS65217_IRQ_AC 1 +#define TPS65217_IRQ_PB 2 + +#endif