Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next

drivers/net/ethernet/intel/e1000e/80003es2lan.c

@@ -764,6 +764,7 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
 {
 	u32 ctrl;
 	s32 ret_val;
+	u16 kum_reg_data;
 
 	/*
 	 * Prevent the PCI-E bus from sticking if there is no TLP connection
@@ -789,6 +790,13 @@ static s32 e1000_reset_hw_80003es2lan(struct e1000_hw *hw)
 	ew32(CTRL, ctrl | E1000_CTRL_RST);
 	e1000_release_phy_80003es2lan(hw);
 
+	/* Disable IBIST slave mode (far-end loopback) */
+	e1000_read_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+					&kum_reg_data);
+	kum_reg_data |= E1000_KMRNCTRLSTA_IBIST_DISABLE;
+	e1000_write_kmrn_reg_80003es2lan(hw, E1000_KMRNCTRLSTA_INBAND_PARAM,
+					 kum_reg_data);
+
 	ret_val = e1000e_get_auto_rd_done(hw);
 	if (ret_val)
 		/* We don't want to continue accessing MAC registers. */

drivers/net/ethernet/intel/e1000e/82571.c

@@ -2062,7 +2062,8 @@ const struct e1000_info e1000_82574_info = {
 				  | FLAG_HAS_CTRLEXT_ON_LOAD,
 	.flags2			  = FLAG2_CHECK_PHY_HANG
 				  | FLAG2_DISABLE_ASPM_L0S
-				  | FLAG2_NO_DISABLE_RX,
+				  | FLAG2_NO_DISABLE_RX
+				  | FLAG2_DMA_BURST,
 	.pba			= 32,
 	.max_hw_frame_size	= DEFAULT_JUMBO,
 	.get_variants		= e1000_get_variants_82571,

drivers/net/ethernet/intel/e1000e/e1000.h

@@ -735,9 +735,46 @@ static inline u32 __er32(struct e1000_hw *hw, unsigned long reg)
 	return readl(hw->hw_addr + reg);
 }
 
+#define er32(reg)	__er32(hw, E1000_##reg)
+
+/**
+ * __ew32_prepare - prepare to write to MAC CSR register on certain parts
+ * @hw: pointer to the HW structure
+ *
+ * When updating the MAC CSR registers, the Manageability Engine (ME) could
+ * be accessing the registers at the same time.  Normally, this is handled in
+ * h/w by an arbiter but on some parts there is a bug that acknowledges Host
+ * accesses later than it should which could result in the register to have
+ * an incorrect value.  Workaround this by checking the FWSM register which
+ * has bit 24 set while ME is accessing MAC CSR registers, wait if it is set
+ * and try again a number of times.
+ **/
+static inline s32 __ew32_prepare(struct e1000_hw *hw)
+{
+	s32 i = E1000_ICH_FWSM_PCIM2PCI_COUNT;
+
+	while ((er32(FWSM) & E1000_ICH_FWSM_PCIM2PCI) && --i)
+		udelay(50);
+
+	return i;
+}
+
 static inline void __ew32(struct e1000_hw *hw, unsigned long reg, u32 val)
 {
+	if (hw->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
+		__ew32_prepare(hw);
+
 	writel(val, hw->hw_addr + reg);
 }
 
+#define ew32(reg, val)	__ew32(hw, E1000_##reg, (val))
+
+#define e1e_flush()	er32(STATUS)
+
+#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) \
+	(__ew32((a), (reg + ((offset) << 2)), (value)))
+
+#define E1000_READ_REG_ARRAY(a, reg, offset) \
+	(readl((a)->hw_addr + reg + ((offset) << 2)))
+
 #endif /* _E1000_H_ */

drivers/net/ethernet/intel/e1000e/hw.h

@@ -36,16 +36,6 @@ struct e1000_adapter;
 
 #include "defines.h"
 
-#define er32(reg)	__er32(hw, E1000_##reg)
-#define ew32(reg,val)	__ew32(hw, E1000_##reg, (val))
-#define e1e_flush()	er32(STATUS)
-
-#define E1000_WRITE_REG_ARRAY(a, reg, offset, value) \
-	(writel((value), ((a)->hw_addr + reg + ((offset) << 2))))
-
-#define E1000_READ_REG_ARRAY(a, reg, offset) \
-	(readl((a)->hw_addr + reg + ((offset) << 2)))
-
 enum e1e_registers {
 	E1000_CTRL     = 0x00000, /* Device Control - RW */
 	E1000_STATUS   = 0x00008, /* Device Status - RO */

drivers/net/ethernet/intel/e1000e/ich8lan.c

@@ -135,6 +135,7 @@
 
 /* PHY Power Management Control */
 #define HV_PM_CTRL		PHY_REG(770, 17)
+#define HV_PM_CTRL_PLL_STOP_IN_K1_GIGA	0x100
 
 /* PHY Low Power Idle Control */
 #define I82579_LPI_CTRL				PHY_REG(772, 20)
@@ -1708,8 +1709,18 @@ static s32 e1000_k1_workaround_lv(struct e1000_hw *hw)
 			return ret_val;
 
 		if (status_reg & HV_M_STATUS_SPEED_1000) {
+			u16 pm_phy_reg;
+
 			mac_reg |= E1000_FEXTNVM4_BEACON_DURATION_8USEC;
 			phy_reg &= ~I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT;
+			/* LV 1G Packet drop issue wa  */
+			ret_val = e1e_rphy(hw, HV_PM_CTRL, &pm_phy_reg);
+			if (ret_val)
+				return ret_val;
+			pm_phy_reg &= ~HV_PM_CTRL_PLL_STOP_IN_K1_GIGA;
+			ret_val = e1e_wphy(hw, HV_PM_CTRL, pm_phy_reg);
+			if (ret_val)
+				return ret_val;
 		} else {
 			mac_reg |= E1000_FEXTNVM4_BEACON_DURATION_16USEC;
 			phy_reg |= I82579_LPI_CTRL_FORCE_PLL_LOCK_COUNT;

drivers/net/ethernet/intel/e1000e/netdev.c

@@ -538,43 +538,15 @@ static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err,
 	adapter->hw_csum_good++;
 }
 
-/**
- * e1000e_update_tail_wa - helper function for e1000e_update_[rt]dt_wa()
- * @hw: pointer to the HW structure
- * @tail: address of tail descriptor register
- * @i: value to write to tail descriptor register
- *
- * When updating the tail register, the ME could be accessing Host CSR
- * registers at the same time.  Normally, this is handled in h/w by an
- * arbiter but on some parts there is a bug that acknowledges Host accesses
- * later than it should which could result in the descriptor register to
- * have an incorrect value.  Workaround this by checking the FWSM register
- * which has bit 24 set while ME is accessing Host CSR registers, wait
- * if it is set and try again a number of times.
- **/
-static inline s32 e1000e_update_tail_wa(struct e1000_hw *hw, void __iomem *tail,
-					unsigned int i)
-{
-	unsigned int j = 0;
-
-	while ((j++ < E1000_ICH_FWSM_PCIM2PCI_COUNT) &&
-	       (er32(FWSM) & E1000_ICH_FWSM_PCIM2PCI))
-		udelay(50);
-
-	writel(i, tail);
-
-	if ((j == E1000_ICH_FWSM_PCIM2PCI_COUNT) && (i != readl(tail)))
-		return E1000_ERR_SWFW_SYNC;
-
-	return 0;
-}
-
 static void e1000e_update_rdt_wa(struct e1000_ring *rx_ring, unsigned int i)
 {
 	struct e1000_adapter *adapter = rx_ring->adapter;
 	struct e1000_hw *hw = &adapter->hw;
+	s32 ret_val = __ew32_prepare(hw);
 
-	if (e1000e_update_tail_wa(hw, rx_ring->tail, i)) {
+	writel(i, rx_ring->tail);
+
+	if (unlikely(!ret_val && (i != readl(rx_ring->tail)))) {
 		u32 rctl = er32(RCTL);
 		ew32(RCTL, rctl & ~E1000_RCTL_EN);
 		e_err("ME firmware caused invalid RDT - resetting\n");
@@ -586,8 +558,11 @@ static void e1000e_update_tdt_wa(struct e1000_ring *tx_ring, unsigned int i)
 {
 	struct e1000_adapter *adapter = tx_ring->adapter;
 	struct e1000_hw *hw = &adapter->hw;
+	s32 ret_val = __ew32_prepare(hw);
 
-	if (e1000e_update_tail_wa(hw, tx_ring->tail, i)) {
+	writel(i, tx_ring->tail);
+
+	if (unlikely(!ret_val && (i != readl(tx_ring->tail)))) {
 		u32 tctl = er32(TCTL);
 		ew32(TCTL, tctl & ~E1000_TCTL_EN);
 		e_err("ME firmware caused invalid TDT - resetting\n");
@@ -1646,6 +1621,9 @@ static void e1000_clean_rx_ring(struct e1000_ring *rx_ring)
 	adapter->flags2 &= ~FLAG2_IS_DISCARDING;
 
 	writel(0, rx_ring->head);
+	if (rx_ring->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
+		e1000e_update_rdt_wa(rx_ring, 0);
+	else
 		writel(0, rx_ring->tail);
 }
 
@@ -2319,6 +2297,9 @@ static void e1000_clean_tx_ring(struct e1000_ring *tx_ring)
 	tx_ring->next_to_clean = 0;
 
 	writel(0, tx_ring->head);
+	if (tx_ring->adapter->flags2 & FLAG2_PCIM2PCI_ARBITER_WA)
+		e1000e_update_tdt_wa(tx_ring, 0);
+	else
 		writel(0, tx_ring->tail);
 }
 

drivers/net/ethernet/intel/igb/igb_main.c

@@ -1715,6 +1715,13 @@ void igb_reset(struct igb_adapter *adapter)
 	if (hw->mac.ops.init_hw(hw))
 		dev_err(&pdev->dev, "Hardware Error\n");
 
+	/*
+	 * Flow control settings reset on hardware reset, so guarantee flow
+	 * control is off when forcing speed.
+	 */
+	if (!hw->mac.autoneg)
+		igb_force_mac_fc(hw);
+
 	igb_init_dmac(adapter, pba);
 	if (!netif_running(adapter->netdev))
 		igb_power_down_link(adapter);

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -600,6 +600,8 @@ extern void ixgbe_disable_rx_queue(struct ixgbe_adapter *adapter,
 				   struct ixgbe_ring *);
 extern void ixgbe_update_stats(struct ixgbe_adapter *adapter);
 extern int ixgbe_init_interrupt_scheme(struct ixgbe_adapter *adapter);
+extern int ixgbe_wol_supported(struct ixgbe_adapter *adapter, u16 device_id,
+			       u16 subdevice_id);
 extern void ixgbe_clear_interrupt_scheme(struct ixgbe_adapter *adapter);
 extern netdev_tx_t ixgbe_xmit_frame_ring(struct sk_buff *,
 					 struct ixgbe_adapter *,

drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c

@@ -1969,53 +1969,12 @@ static int ixgbe_wol_exclusion(struct ixgbe_adapter *adapter,
                                struct ethtool_wolinfo *wol)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
-	int retval = 1;
+	int retval = 0;
-	u16 wol_cap = adapter->eeprom_cap & IXGBE_DEVICE_CAPS_WOL_MASK;
 
-	/* WOL not supported except for the following */
+	/* WOL not supported for all devices */
-	switch(hw->device_id) {
+	if (!ixgbe_wol_supported(adapter, hw->device_id,
-	case IXGBE_DEV_ID_82599_SFP:
+				 hw->subsystem_device_id)) {
-		/* Only these subdevices could supports WOL */
+		retval = 1;
-		switch (hw->subsystem_device_id) {
-		case IXGBE_SUBDEV_ID_82599_560FLR:
-			/* only support first port */
-			if (hw->bus.func != 0) {
-				wol->supported = 0;
-				break;
-			}
-		case IXGBE_SUBDEV_ID_82599_SFP:
-			retval = 0;
-			break;
-		default:
-			wol->supported = 0;
-			break;
-		}
-		break;
-	case IXGBE_DEV_ID_82599_COMBO_BACKPLANE:
-		/* All except this subdevice support WOL */
-		if (hw->subsystem_device_id ==
-		    IXGBE_SUBDEV_ID_82599_KX4_KR_MEZZ) {
-			wol->supported = 0;
-			break;
-		}
-		retval = 0;
-		break;
-	case IXGBE_DEV_ID_82599_KX4:
-		retval = 0;
-		break;
-	case IXGBE_DEV_ID_X540T:
-		/* check eeprom to see if enabled wol */
-		if ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0_1) ||
-		    ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0) &&
-		     (hw->bus.func == 0))) {
-			retval = 0;
-			break;
-		}
-
-		/* All others not supported */
-		wol->supported = 0;
-		break;
-	default:
 		wol->supported = 0;
 	}
 

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c

@@ -6785,6 +6785,57 @@ static void __devinit ixgbe_probe_vf(struct ixgbe_adapter *adapter,
 #endif /* CONFIG_PCI_IOV */
 }
 
+/**
+ * ixgbe_wol_supported - Check whether device supports WoL
+ * @hw: hw specific details
+ * @device_id: the device ID
+ * @subdev_id: the subsystem device ID
+ *
+ * This function is used by probe and ethtool to determine
+ * which devices have WoL support
+ *
+ **/
+int ixgbe_wol_supported(struct ixgbe_adapter *adapter, u16 device_id,
+			u16 subdevice_id)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+	u16 wol_cap = adapter->eeprom_cap & IXGBE_DEVICE_CAPS_WOL_MASK;
+	int is_wol_supported = 0;
+
+	switch (device_id) {
+	case IXGBE_DEV_ID_82599_SFP:
+		/* Only these subdevices could supports WOL */
+		switch (subdevice_id) {
+		case IXGBE_SUBDEV_ID_82599_560FLR:
+			/* only support first port */
+			if (hw->bus.func != 0)
+				break;
+		case IXGBE_SUBDEV_ID_82599_SFP:
+			is_wol_supported = 1;
+			break;
+		}
+		break;
+	case IXGBE_DEV_ID_82599_COMBO_BACKPLANE:
+		/* All except this subdevice support WOL */
+		if (subdevice_id != IXGBE_SUBDEV_ID_82599_KX4_KR_MEZZ)
+			is_wol_supported = 1;
+		break;
+	case IXGBE_DEV_ID_82599_KX4:
+		is_wol_supported = 1;
+		break;
+	case IXGBE_DEV_ID_X540T:
+		/* check eeprom to see if enabled wol */
+		if ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0_1) ||
+		    ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0) &&
+		     (hw->bus.func == 0))) {
+			is_wol_supported = 1;
+		}
+		break;
+	}
+
+	return is_wol_supported;
+}
+
 /**
  * ixgbe_probe - Device Initialization Routine
  * @pdev: PCI device information struct
@@ -6811,7 +6862,6 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
 	u16 device_caps;
 #endif
 	u32 eec;
-	u16 wol_cap;
 
 	/* Catch broken hardware that put the wrong VF device ID in
 	 * the PCIe SR-IOV capability.
@@ -7075,40 +7125,12 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev,
 		netdev->features &= ~NETIF_F_RXHASH;
 	}
 
-	/* WOL not supported for all but the following */
+	/* WOL not supported for all devices */
 	adapter->wol = 0;
-	switch (pdev->device) {
-	case IXGBE_DEV_ID_82599_SFP:
-		/* Only these subdevice supports WOL */
-		switch (pdev->subsystem_device) {
-		case IXGBE_SUBDEV_ID_82599_560FLR:
-			/* only support first port */
-			if (hw->bus.func != 0)
-				break;
-		case IXGBE_SUBDEV_ID_82599_SFP:
-			adapter->wol = IXGBE_WUFC_MAG;
-			break;
-		}
-		break;
-	case IXGBE_DEV_ID_82599_COMBO_BACKPLANE:
-		/* All except this subdevice support WOL */
-		if (pdev->subsystem_device != IXGBE_SUBDEV_ID_82599_KX4_KR_MEZZ)
-			adapter->wol = IXGBE_WUFC_MAG;
-		break;
-	case IXGBE_DEV_ID_82599_KX4:
-		adapter->wol = IXGBE_WUFC_MAG;
-		break;
-	case IXGBE_DEV_ID_X540T:
-		/* Check eeprom to see if it is enabled */
 	hw->eeprom.ops.read(hw, 0x2c, &adapter->eeprom_cap);
-		wol_cap = adapter->eeprom_cap & IXGBE_DEVICE_CAPS_WOL_MASK;
+	if (ixgbe_wol_supported(adapter, pdev->device, pdev->subsystem_device))
-
-		if ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0_1) ||
-		    ((wol_cap == IXGBE_DEVICE_CAPS_WOL_PORT0) &&
-		     (hw->bus.func == 0)))
 		adapter->wol = IXGBE_WUFC_MAG;
-		break;
+
-	}
 	device_set_wakeup_enable(&adapter->pdev->dev, adapter->wol);
 
 	/* save off EEPROM version number */