From ec49a86ce0c6202ddf53c8e940c3468b4fb7e042 Mon Sep 17 00:00:00 2001 From: Fugang Duan Date: Thu, 16 Jul 2015 16:26:45 +0800 Subject: [PATCH 1/9] ARM: dts: omap3: correct the format of u16 values for tsc2046 node In tsc2046 touch driver, the values such as ti,x-min is defined as a u16 value. the driver use API of_property_read_u16() read the value. For these u16 value, the dts entry should be like: property = /bits/ 16 <0x5000>; This describes the property as a u16 value. Signed-off-by: Fugang Duan Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-lilly-a83x.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi index e63133304a34..d0dd0365bfda 100644 --- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi @@ -319,12 +319,12 @@ pinctrl-names = "default"; pinctrl-0 = <&tsc2048_pins>; - ti,x-min = <300>; - ti,x-max = <3000>; - ti,y-min = <600>; - ti,y-max = <3600>; - ti,x-plate-ohms = <80>; - ti,pressure-max = <255>; + ti,x-min = /bits/ 16 <300>; + ti,x-max = /bits/ 16 <3000>; + ti,y-min = /bits/ 16 <600>; + ti,y-max = /bits/ 16 <3600>; + ti,x-plate-ohms = /bits/ 16 <80>; + ti,pressure-max = /bits/ 16 <255>; ti,swap-xy; linux,wakeup; From 52b0dcb1d160f9ac839acd6b44b0687e82e23e98 Mon Sep 17 00:00:00 2001 From: Teresa Remmet Date: Thu, 16 Jul 2015 10:30:48 +0200 Subject: [PATCH 2/9] ARM: dts: Add support for phyCORE-AM335x SoM phyCORE-AM335x is a SoM (System on Module) containing a AM335x SOC. The module can be connected to different carrier boards. Some hardware parts are configurable on the phyCORE-AM335x. So they are disabled on default in this som dtsi file. They will be enabled in the board dts files, when populated. * RAM up to 1GiB * PMIC * NAND flash up to 1GiB * Eth PHY on SOM: 1x RMII * SPI NOR flash 8MiB (optional) * i2c RTC (optional) * i2c EEPROM 4kiB (optional) Signed-off-by: Teresa Remmet Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-phycore-som.dtsi | 368 ++++++++++++++++++++++ 1 file changed, 368 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-phycore-som.dtsi diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi new file mode 100644 index 000000000000..4d28fc3aac69 --- /dev/null +++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi @@ -0,0 +1,368 @@ +/* + * Copyright (C) 2015 Phytec Messtechnik GmbH + * Author: Teresa Remmet + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "am33xx.dtsi" + +/ { + model = "Phytec AM335x phyCORE"; + compatible = "phytec,am335x-phycore-som", "ti,am33xx"; + + aliases { + rtc0 = &i2c_rtc; + rtc1 = &rtc; + }; + + cpus { + cpu@0 { + cpu0-supply = <&vdd1_reg>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + vbat: fixedregulator@0 { + compatible = "regulator-fixed"; + }; +}; + +/* Crypto Module */ +&aes { + status = "okay"; +}; + +&sham { + status = "okay"; +}; + +/* Ethernet */ +&am33xx_pinmux { + ethernet0_pins: pinmux_ethernet0 { + pinctrl-single,pins = < + 0x10c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_crs.rmii1_crs_dv */ + 0x110 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxerr.rmii1_rxerr */ + 0x114 (PIN_OUTPUT | MUX_MODE1) /* mii1_txen.rmii1_txen */ + 0x124 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd1.rmii1_txd1 */ + 0x128 (PIN_OUTPUT | MUX_MODE1) /* mii1_txd0.rmii1_txd0 */ + 0x13c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd1.rmii1_rxd1 */ + 0x140 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* mii1_rxd0.rmii1_rxd0 */ + 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii1_refclk.rmii1_refclk */ + >; + }; + + mdio_pins: pinmux_mdio { + pinctrl-single,pins = < + /* MDIO */ + 0x148 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* mdio_data.mdio_data */ + 0x14c (PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */ + >; + }; +}; + +&cpsw_emac0 { + phy_id = <&davinci_mdio>, <0>; + phy-mode = "rmii"; + dual_emac_res_vlan = <1>; +}; + +&davinci_mdio { + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + status = "okay"; +}; + +&mac { + slaves = <1>; + pinctrl-names = "default"; + pinctrl-0 = <ðernet0_pins>; + status = "okay"; +}; + +&phy_sel { + rmii-clock-ext; +}; + +/* I2C Busses */ +&am33xx_pinmux { + i2c0_pins: pinmux_i2c0 { + pinctrl-single,pins = < + 0x188 (PIN_INPUT | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; + clock-frequency = <400000>; + status = "okay"; + + tps: pmic@2d { + reg = <0x2d>; + }; + + i2c_eeprom: eeprom@52 { + compatible = "atmel,24c32"; + pagesize = <32>; + reg = <0x52>; + status = "disabled"; + }; + + i2c_rtc: rtc@68 { + compatible = "rv4162"; + reg = <0x68>; + status = "disabled"; + }; +}; + +/* NAND memory */ +&am33xx_pinmux { + nandflash_pins: pinmux_nandflash { + pinctrl-single,pins = < + 0x0 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nandflash_pins>; + ranges = <0 0 0x08000000 0x1000000>; /* CS0: NAND */ + nandflash: nand@0,0 { + reg = <0 0 4>; /* CS0, offset 0, IO size 4 */ + nand-bus-width = <8>; + ti,nand-ecc-opt = "bch8"; + gpmc,device-nand = "true"; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <30>; + gpmc,cs-wr-off-ns = <30>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <30>; + gpmc,adv-wr-off-ns = <30>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <20>; + gpmc,oe-on-ns = <10>; + gpmc,oe-off-ns = <30>; + gpmc,access-ns = <30>; + gpmc,rd-cycle-ns = <30>; + gpmc,wr-cycle-ns = <30>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <50>; + gpmc,cycle2cycle-diffcsen; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <30>; + gpmc,wr-data-mux-bus-ns = <0>; + + elm_id = <&elm>; + + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "xload"; + reg = <0x0 0x20000>; + }; + partition@1 { + label = "xload_backup1"; + reg = <0x20000 0x20000>; + }; + partition@2 { + label = "xload_backup2"; + reg = <0x40000 0x20000>; + }; + partition@3 { + label = "xload_backup3"; + reg = <0x60000 0x20000>; + }; + partition@4 { + label = "barebox"; + reg = <0x80000 0x80000>; + }; + partition@5 { + label = "bareboxenv"; + reg = <0x100000 0x40000>; + }; + partition@6 { + label = "oftree"; + reg = <0x140000 0x40000>; + }; + partition@7 { + label = "kernel"; + reg = <0x180000 0x800000>; + }; + partition@8 { + label = "root"; + reg = <0x980000 0x0>; + }; + }; +}; + +/* Power */ +#include "tps65910.dtsi" + +&tps { + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */ + regulator-name = "vdd_mpu"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1312500>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <912500>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd3_reg: regulator@4 { + regulator-always-on; + }; + + vdig1_reg: regulator@5 { + regulator-name = "vdig1_1p8v"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vdig2_reg: regulator@6 { + regulator-always-on; + }; + + vpll_reg: regulator@7 { + regulator-always-on; + }; + + vdac_reg: regulator@8 { + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + regulator-always-on; + }; + + vaux33_reg: regulator@11 { + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; +}; + +&vbat { + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; +}; + +/* SPI Busses */ +&am33xx_pinmux { + spi0_pins: pinmux_spi0 { + pinctrl-single,pins = < + 0x150 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_clk.spi0_clk */ + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* spi0_d0.spi0_d0 */ + 0x158 (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_d1.spi0_d1 */ + 0x15c (PIN_INPUT_PULLUP | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + >; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "okay"; + + serial_flash: m25p80@0 { + compatible = "m25p80"; + spi-max-frequency = <48000000>; + reg = <0x0>; + m25p,fast-read; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "xload"; + reg = <0x0 0x20000>; + }; + partition@1 { + label = "barebox"; + reg = <0x20000 0x80000>; + }; + partition@2 { + label = "bareboxenv"; + reg = <0xa0000 0x20000>; + }; + partition@3 { + label = "oftree"; + reg = <0xc0000 0x20000>; + }; + partition@4 { + label = "kernel"; + reg = <0xe0000 0x0>; + }; + }; +}; From 36bd1683559e23d4032defadbfbd3ccd5601b8c8 Mon Sep 17 00:00:00 2001 From: Teresa Remmet Date: Thu, 16 Jul 2015 10:30:49 +0200 Subject: [PATCH 3/9] ARM: dts: Add phyBOARD-WEGA-AM335x rdk phyBOARD-WEGA-AM335x represents a direct soldered combination of a phyCORE-AM335x SoM and carrier board. Different kind of SoM options can be connected to the wega carrier board. So we created a separate wega dtsi file. The final dts contains the actual SoM on the carrier board. WEGA carrier board features: * ETH phy on carrier board: 1x MII * 1x CAN * 2x UART * USB0 (device) * USB1 (host) * mSD slot Signed-off-by: Teresa Remmet Signed-off-by: Tony Lindgren --- .../devicetree/bindings/arm/omap/omap.txt | 3 + arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/am335x-wega-rdk.dts | 22 +++ arch/arm/boot/dts/am335x-wega.dtsi | 151 ++++++++++++++++++ 4 files changed, 178 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/am335x-wega-rdk.dts create mode 100644 arch/arm/boot/dts/am335x-wega.dtsi diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index 4f6a82cef1d1..9f4e5136e568 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -135,6 +135,9 @@ Boards: - AM335X OrionLXm : Substation Automation Platform compatible = "novatech,am335x-lxm", "ti,am33xx" +- AM335X phyBOARD-WEGA: Single Board Computer dev kit + compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx" + - OMAP5 EVM : Evaluation Module compatible = "ti,omap5-evm", "ti,omap5" diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 1c62928587e0..180846365081 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -442,7 +442,8 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-nano.dtb \ am335x-pepper.dtb \ am335x-lxm.dtb \ - am335x-chiliboard.dtb + am335x-chiliboard.dtb \ + am335x-wega-rdk.dtb dtb-$(CONFIG_ARCH_OMAP4) += \ omap4-duovero-parlor.dtb \ omap4-panda.dtb \ diff --git a/arch/arm/boot/dts/am335x-wega-rdk.dts b/arch/arm/boot/dts/am335x-wega-rdk.dts new file mode 100644 index 000000000000..6431b7db8109 --- /dev/null +++ b/arch/arm/boot/dts/am335x-wega-rdk.dts @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2015 Phytec Messtechnik GmbH + * Author: Teresa Remmet + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; + +#include "am335x-phycore-som.dtsi" +#include "am335x-wega.dtsi" + +/* SoM */ +&i2c_eeprom { + status = "okay"; +}; + +&i2c_rtc { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi new file mode 100644 index 000000000000..5e541bd1b45a --- /dev/null +++ b/arch/arm/boot/dts/am335x-wega.dtsi @@ -0,0 +1,151 @@ +/* + * Copyright (C) 2015 Phytec Messtechnik GmbH + * Author: Teresa Remmet + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + model = "Phytec AM335x phyBOARD-WEGA"; + compatible = "phytec,am335x-wega", "phytec,am335x-phycore-som", "ti,am33xx"; + +}; + +/* CAN Busses */ +&am33xx_pinmux { + dcan1_pins: pinmux_dcan1 { + pinctrl-single,pins = < + 0x168 (PIN_OUTPUT_PULLUP | MUX_MODE2) /* uart0_ctsn.d_can1_tx */ + 0x16c (PIN_INPUT_PULLUP | MUX_MODE2) /* uart0_rtsn.d_can1_rx */ + >; + }; +}; + +&dcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&dcan1_pins>; + status = "okay"; +}; + +/* Ethernet */ +&am33xx_pinmux { + ethernet1_pins: pinmux_ethernet1 { + pinctrl-single,pins = < + 0x40 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a0.mii2_txen */ + 0x44 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a1.mii2_rxdv */ + 0x48 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a2.mii2_txd3 */ + 0x4c (PIN_OUTPUT | MUX_MODE1) /* gpmc_a3.mii2_txd2 */ + 0x50 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a4.mii2_txd1 */ + 0x54 (PIN_OUTPUT | MUX_MODE1) /* gpmc_a5.mii2_txd0 */ + 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a6.mii2_txclk */ + 0x5c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a7.mii2_rxclk */ + 0x60 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a8.mii2_rxd3 */ + 0x64 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a9.mii2_rxd2 */ + 0x68 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a10.mii2_rxd1 */ + 0x6c (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_a11.mii2_rxd0 */ + 0x74 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_wpn.mii2_rxerr */ + 0x78 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* gpmc_ben1.mii2_col */ + >; + }; +}; + +&cpsw_emac1 { + phy_id = <&davinci_mdio>, <1>; + phy-mode = "mii"; + dual_emac_res_vlan = <2>; +}; + +&mac { + slaves = <2>; + pinctrl-names = "default"; + pinctrl-0 = <ðernet0_pins ðernet1_pins>; + dual_emac = <1>; +}; + +/* MMC */ +&am33xx_pinmux { + mmc1_pins: pinmux_mmc1 { + pinctrl-single,pins = < + 0x0F0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat3.mmc0_dat3 */ + 0x0F4 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat2.mmc0_dat2 */ + 0x0F8 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat1.mmc0_dat1 */ + 0x0FC (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_dat0.mmc0_dat0 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_clk.mmc0_clk */ + 0x104 (PIN_INPUT_PULLUP | MUX_MODE0) /* mmc0_cmd.mmc0_cmd */ + 0x160 (PIN_INPUT_PULLUP | MUX_MODE7) /* spi0_cs1.mmc0_sdcd */ + >; + }; +}; + +&mmc1 { + vmmc-supply = <&vmmc_reg>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +/* UARTs */ +&am33xx_pinmux { + uart0_pins: pinmux_uart0 { + pinctrl-single,pins = < + 0x170 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart0_rxd.uart0_rxd */ + 0x174 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart0_txd.uart0_txd */ + >; + }; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */ + 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */ + 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */ + 0x17c (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */ + >; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +/* USB */ +&cppi41dma { + status = "okay"; +}; + +&usb_ctrl_mod { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb0 { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb0_phy { + status = "okay"; +}; + +&usb1 { + dr_mode = "host"; + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; From 71256d9d0be7a371ad2072e08dc7c6da3e71ed9e Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 20 Jul 2015 16:42:20 +0530 Subject: [PATCH 4/9] ARM: dts: am437x: add aliases for all UART instances Add serialN aliases for all 6 UART instances on the AM437x SoC so each board's .dts file does not have to define its own aliases. Remove the alias added for am437x-gp-evm.dts now that we have the aliases defined in am4372.dtsi file. Signed-off-by: Sekhar Nori Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am4372.dtsi | 5 +++++ arch/arm/boot/dts/am437x-gp-evm.dts | 1 - 2 files changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 6f6f3931ec2d..1db7c75b6596 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -23,6 +23,11 @@ i2c1 = &i2c1; i2c2 = &i2c2; serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; ethernet0 = &cpsw_emac0; ethernet1 = &cpsw_emac1; }; diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 8e6ada75c428..58cfad28f483 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -21,7 +21,6 @@ aliases { display0 = &lcd0; - serial3 = &uart3; }; evm_v3_3d: fixedregulator-v3_3d { From a60011c1f4204285f18edd61859456caf5ecbbb6 Mon Sep 17 00:00:00 2001 From: Aparna Balasubramanian Date: Mon, 20 Jul 2015 16:07:31 -0500 Subject: [PATCH 5/9] ARM: dts: omap5-uevm: Add Palmas power button support Palmas on OMAP5uevm has support for power button, so enable it. Signed-off-by: Aparna Balasubramanian Acked-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-uevm.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 275618f19a43..3cc8f357d5b8 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -510,6 +510,13 @@ }; }; }; + + palmas_power_button: palmas_power_button { + compatible = "ti,palmas-pwrbutton"; + interrupt-parent = <&palmas>; + interrupts = <1 IRQ_TYPE_EDGE_FALLING>; + wakeup-source; + }; }; twl6040: twl@4b { From a4e1adb98f7376dccbfaee7c375e6378b6c21985 Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Tue, 21 Jul 2015 04:11:58 +0300 Subject: [PATCH 6/9] ARM: dts: omap3-pandora: miscellaneous corrections - add pandora specific compatible name - fix mmc2 card detect polarity - fix mmc1 and mmc2 write protect polarity - disable write protect pins because of production issue and add an explanation why they are disabled - fix NAND partition name to reflect the correct address Signed-off-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-pandora-1ghz.dts | 2 +- arch/arm/boot/dts/omap3-pandora-600mhz.dts | 2 +- arch/arm/boot/dts/omap3-pandora-common.dtsi | 13 +++++++++---- 3 files changed, 11 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/omap3-pandora-1ghz.dts b/arch/arm/boot/dts/omap3-pandora-1ghz.dts index 9619a28dfd7d..25498f756a29 100644 --- a/arch/arm/boot/dts/omap3-pandora-1ghz.dts +++ b/arch/arm/boot/dts/omap3-pandora-1ghz.dts @@ -19,7 +19,7 @@ / { model = "Pandora Handheld Console 1GHz"; - compatible = "ti,omap36xx", "ti,omap3"; + compatible = "openpandora,omap3-pandora-1ghz", "ti,omap36xx", "ti,omap3"; }; &omap3_pmx_core2 { diff --git a/arch/arm/boot/dts/omap3-pandora-600mhz.dts b/arch/arm/boot/dts/omap3-pandora-600mhz.dts index fb803a70a2bb..8775897a4ce7 100644 --- a/arch/arm/boot/dts/omap3-pandora-600mhz.dts +++ b/arch/arm/boot/dts/omap3-pandora-600mhz.dts @@ -19,7 +19,7 @@ / { model = "Pandora Handheld Console"; - compatible = "ti,omap3"; + compatible = "openpandora,omap3-pandora-600mhz", "ti,omap3430", "ti,omap3"; }; &omap3_pmx_core2 { diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index 782ab1ff1d08..f6363bccca53 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -459,13 +459,18 @@ power = <50>; }; +/* + * Many pandora boards have been produced with defective write-protect switches + * on either slot, so it was decided not to use this feature. If you know + * your board has good switches, feel free to uncomment wp-gpios below. + */ &mmc1 { pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; vmmc-supply = <&vmmc1>; bus-width = <4>; cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_LOW>; - wp-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; /* GPIO_126 */ + /*wp-gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;*/ /* GPIO_126 */ }; &mmc2 { @@ -473,8 +478,8 @@ pinctrl-0 = <&mmc2_pins>; vmmc-supply = <&vmmc2>; bus-width = <4>; - cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_HIGH>; - wp-gpios = <&gpio4 31 GPIO_ACTIVE_LOW>; /* GPIO_127 */ + cd-gpios = <&twl_gpio 1 GPIO_ACTIVE_LOW>; + /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/ /* GPIO_127 */ }; /* bluetooth*/ @@ -545,7 +550,7 @@ reg = <0x280000 0xa00000>; }; - filesystem@680000 { + filesystem@c80000 { label = "rootfs"; reg = <0xc80000 0>; /* 0 = MTDPART_SIZ_FULL */ }; From f7c57f8c7b464c0fbcd67764c38e21aebb7085c4 Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Tue, 21 Jul 2015 04:11:59 +0300 Subject: [PATCH 7/9] ARM: dts: omap3-pandora: add support for usb host and 32k buffer This adds missing bits for EHCI HS USB host support and 32k clock buffer control for the wg7210 bt+wifi module. Signed-off-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-pandora-common.dtsi | 36 +++++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index f6363bccca53..6e82c4aed91f 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -199,6 +199,38 @@ gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; /* GPIO_108 */ }; }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; /* GPIO_16 */ + vcc-supply = <&vaux2>; + }; + + /* HS USB Host VBUS supply + * disabling this regulator causes current leakage, and LCD flicker + * on earlier (CC) board revisions, so keep it always on */ + usb_host_5v: fixed-regulator-usb_host_5v { + compatible = "regulator-fixed"; + regulator-name = "usb_host_5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&gpio6 4 0>; /* GPIO_164 */ + }; + + /* wg7210 (wifi+bt module) 32k clock buffer */ + wg7210_32k: fixed-regulator-wg7210_32k { + compatible = "regulator-fixed"; + regulator-name = "wg7210_32k"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + enable-active-high; + gpio = <&twl_gpio 13 GPIO_ACTIVE_HIGH>; + }; }; &omap3_pmx_core { @@ -501,6 +533,10 @@ port2-mode = "ehci-phy"; }; +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + &gpmc { ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */ From fc53e2ccf000b45298a325a6b6c3560d4ba8932b Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Tue, 21 Jul 2015 04:12:00 +0300 Subject: [PATCH 8/9] ARM: OMAP2+: omap3-pandora: add backlight support Add backlight support via pdata-quirks as it's driver lacks DT support. Signed-off-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/pdata-quirks.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 5417f2cbb2d4..9bfb47a4756e 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -269,6 +269,16 @@ static void __init omap3_tao3530_legacy_init(void) { hsmmc2_internal_input_clk(); } + +static struct platform_device pandora_backlight = { + .name = "pandora-backlight", + .id = -1, +}; + +static void __init omap3_pandora_legacy_init(void) +{ + platform_device_register(&pandora_backlight); +} #endif /* CONFIG_ARCH_OMAP3 */ #if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) @@ -396,6 +406,8 @@ static struct pdata_init pdata_quirks[] __initdata = { { "ti,omap3-evm-37xx", omap3_evm_legacy_init, }, { "ti,am3517-evm", am3517_evm_legacy_init, }, { "technexion,omap3-tao3530", omap3_tao3530_legacy_init, }, + { "openpandora,omap3-pandora-600mhz", omap3_pandora_legacy_init, }, + { "openpandora,omap3-pandora-1ghz", omap3_pandora_legacy_init, }, #endif #ifdef CONFIG_SOC_OMAP5 { "ti,omap5-uevm", omap5_uevm_legacy_init, }, From f9d50fef4b6447527c2be1ad07499221c2511391 Mon Sep 17 00:00:00 2001 From: Grazvydas Ignotas Date: Tue, 21 Jul 2015 04:12:01 +0300 Subject: [PATCH 9/9] ARM: OMAP2+: omap3-pandora: add wifi support Add wl1251 support via pdata-quirks as it's driver lacks DT support. MMC3 is marked disabled in DT so that MMC3 instance of hsmmc driver is probed using platform data with special card init callback. Signed-off-by: Grazvydas Ignotas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-pandora-common.dtsi | 5 + arch/arm/mach-omap2/pdata-quirks.c | 101 ++++++++++++++++++++ 2 files changed, 106 insertions(+) diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi index 6e82c4aed91f..f2084e6d01e7 100644 --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi @@ -514,6 +514,11 @@ /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/ /* GPIO_127 */ }; +/* mmc3 is probed using pdata-quirks to pass wl1251 card data */ +&mmc3 { + status = "disabled"; +}; + /* bluetooth*/ &uart1 { }; diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index 9bfb47a4756e..4e655ae2d507 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -14,6 +14,11 @@ #include #include #include +#include +#include +#include +#include +#include #include #include @@ -26,6 +31,7 @@ #include "omap_device.h" #include "omap-secure.h" #include "soc.h" +#include "hsmmc.h" struct pdata_init { const char *compatible; @@ -270,14 +276,109 @@ static void __init omap3_tao3530_legacy_init(void) hsmmc2_internal_input_clk(); } +/* omap3pandora legacy devices */ +#define PANDORA_WIFI_IRQ_GPIO 21 +#define PANDORA_WIFI_NRESET_GPIO 23 + static struct platform_device pandora_backlight = { .name = "pandora-backlight", .id = -1, }; +static struct regulator_consumer_supply pandora_vmmc3_supply[] = { + REGULATOR_SUPPLY("vmmc", "omap_hsmmc.2"), +}; + +static struct regulator_init_data pandora_vmmc3 = { + .constraints = { + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + }, + .num_consumer_supplies = ARRAY_SIZE(pandora_vmmc3_supply), + .consumer_supplies = pandora_vmmc3_supply, +}; + +static struct fixed_voltage_config pandora_vwlan = { + .supply_name = "vwlan", + .microvolts = 1800000, /* 1.8V */ + .gpio = PANDORA_WIFI_NRESET_GPIO, + .startup_delay = 50000, /* 50ms */ + .enable_high = 1, + .init_data = &pandora_vmmc3, +}; + +static struct platform_device pandora_vwlan_device = { + .name = "reg-fixed-voltage", + .id = 1, + .dev = { + .platform_data = &pandora_vwlan, + }, +}; + +static void pandora_wl1251_init_card(struct mmc_card *card) +{ + /* + * We have TI wl1251 attached to MMC3. Pass this information to + * SDIO core because it can't be probed by normal methods. + */ + if (card->type == MMC_TYPE_SDIO || card->type == MMC_TYPE_SD_COMBO) { + card->quirks |= MMC_QUIRK_NONSTD_SDIO; + card->cccr.wide_bus = 1; + card->cis.vendor = 0x104c; + card->cis.device = 0x9066; + card->cis.blksize = 512; + card->cis.max_dtr = 24000000; + card->ocr = 0x80; + } +} + +static struct omap2_hsmmc_info pandora_mmc3[] = { + { + .mmc = 3, + .caps = MMC_CAP_4_BIT_DATA | MMC_CAP_POWER_OFF_CARD, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + .init_card = pandora_wl1251_init_card, + }, + {} /* Terminator */ +}; + +static void __init pandora_wl1251_init(void) +{ + struct wl1251_platform_data pandora_wl1251_pdata; + int ret; + + memset(&pandora_wl1251_pdata, 0, sizeof(pandora_wl1251_pdata)); + + pandora_wl1251_pdata.power_gpio = -1; + + ret = gpio_request_one(PANDORA_WIFI_IRQ_GPIO, GPIOF_IN, "wl1251 irq"); + if (ret < 0) + goto fail; + + pandora_wl1251_pdata.irq = gpio_to_irq(PANDORA_WIFI_IRQ_GPIO); + if (pandora_wl1251_pdata.irq < 0) + goto fail_irq; + + pandora_wl1251_pdata.use_eeprom = true; + ret = wl1251_set_platform_data(&pandora_wl1251_pdata); + if (ret < 0) + goto fail_irq; + + return; + +fail_irq: + gpio_free(PANDORA_WIFI_IRQ_GPIO); +fail: + pr_err("wl1251 board initialisation failed\n"); +} + static void __init omap3_pandora_legacy_init(void) { platform_device_register(&pandora_backlight); + platform_device_register(&pandora_vwlan_device); + omap_hsmmc_init(pandora_mmc3); + omap_hsmmc_late_init(pandora_mmc3); + pandora_wl1251_init(); } #endif /* CONFIG_ARCH_OMAP3 */