ARM: dts: omap: update usb_otg_hs data

Updated the usb_otg_hs dt data to include the *phy* and *phy-names*
binding in order for the driver to use the new generic PHY framework.
Also updated the Documentation to include the binding information.
The PHY binding information can be found at
Documentation/devicetree/bindings/phy/phy-bindings.txt

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit is contained in:
Kishon Vijay Abraham I 2013-09-27 11:53:29 +05:30 committed by Greg Kroah-Hartman
parent 6c27f939b8
commit 975d963e6d
7 changed files with 21 additions and 0 deletions

View File

@ -19,6 +19,9 @@ OMAP MUSB GLUE
- power : Should be "50". This signifies the controller can supply up to
100mA when operating in host mode.
- usb-phy : the phandle for the PHY device
- phys : the phandle for the PHY device (used by generic PHY framework)
- phy-names : the names of the PHY corresponding to the PHYs present in the
*phy* phandle.
Optional properties:
- ctrl-module : phandle of the control module this glue uses to write to
@ -33,6 +36,8 @@ usb_otg_hs: usb_otg_hs@4a0ab000 {
num-eps = <16>;
ram-bits = <12>;
ctrl-module = <&omap_control_usb>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
};
Board specific device node entry

View File

@ -5,6 +5,8 @@ OMAP USB2 PHY
Required properties:
- compatible: Should be "ti,omap-usb2"
- reg : Address and length of the register set for the device.
- #phy-cells: determine the number of cells that should be given in the
phandle while referencing this phy.
Optional properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
@ -16,6 +18,7 @@ usb2phy@4a0ad080 {
compatible = "ti,omap-usb2";
reg = <0x4a0ad080 0x58>;
ctrl-module = <&omap_control_usb>;
#phy-cells = <0>;
};
OMAP USB3 PHY
@ -25,6 +28,8 @@ Required properties:
- reg : Address and length of the register set for the device.
- reg-names: The names of the register addresses corresponding to the registers
filled in "reg".
- #phy-cells: determine the number of cells that should be given in the
phandle while referencing this phy.
Optional properties:
- ctrl-module : phandle of the control module used by PHY driver to power on
@ -39,4 +44,5 @@ usb3phy@4a084400 {
<0x4a084c00 0x40>;
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
ctrl-module = <&omap_control_usb>;
#phy-cells = <0>;
};

View File

@ -144,6 +144,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};

View File

@ -70,6 +70,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};

View File

@ -76,6 +76,8 @@
&usb_otg_hs {
interface-type = <0>;
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
mode = <3>;
power = <50>;
};

View File

@ -520,6 +520,7 @@
compatible = "ti,omap-usb2";
reg = <0x4a0ad080 0x58>;
ctrl-module = <&omap_control_usb>;
#phy-cells = <0>;
};
};
@ -658,6 +659,8 @@
interrupt-names = "mc", "dma";
ti,hwmods = "usb_otg_hs";
usb-phy = <&usb2_phy>;
phys = <&usb2_phy>;
phy-names = "usb2-phy";
multipoint = <1>;
num-eps = <16>;
ram-bits = <12>;

View File

@ -86,6 +86,7 @@
usb1v8-supply = <&vusb1v8>;
usb3v1-supply = <&vusb3v1>;
usb_mode = <1>;
#phy-cells = <0>;
};
twl_pwm: pwm {