Merge branch 'wm97xx'

drivers/input/touchscreen/wm97xx-core.c

@@ -261,6 +261,23 @@ void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio, enum wm97xx_gpio_dir dir,
 }
 EXPORT_SYMBOL_GPL(wm97xx_config_gpio);
 
+/*
+ * Configure the WM97XX_PRP value to use while system is suspended.
+ * If a value other than 0 is set then WM97xx pen detection will be
+ * left enabled in the configured mode while the system is in suspend,
+ * the device has users and suspend has not been disabled via the
+ * wakeup sysfs entries.
+ *
+ * @wm:   WM97xx device to configure
+ * @mode: WM97XX_PRP value to configure while suspended
+ */
+void wm97xx_set_suspend_mode(struct wm97xx *wm, u16 mode)
+{
+	wm->suspend_mode = mode;
+	device_init_wakeup(&wm->input_dev->dev, mode != 0);
+}
+EXPORT_SYMBOL_GPL(wm97xx_set_suspend_mode);
+
 /*
  * Handle a pen down interrupt.
  */
@@ -328,18 +345,18 @@ static void wm97xx_pen_irq_worker(struct work_struct *work)
  *
  * We have to disable the codec interrupt in the handler because it
  * can take upto 1ms to clear the interrupt source. We schedule a task
- * in a work queue to do the actual interaction with the chip (it
+ * in a work queue to do the actual interaction with the chip.  The
- * doesn't matter if we end up reenqueing it before it is executed
+ * interrupt is then enabled again in the slow handler when the source
- * since we don't touch the chip until it has run).  The interrupt is
+ * has been cleared.
- * then enabled again in the slow handler when the source has been
- * cleared.
  */
 static irqreturn_t wm97xx_pen_interrupt(int irq, void *dev_id)
 {
 	struct wm97xx *wm = dev_id;
 
-	wm->mach_ops->irq_enable(wm, 0);
+	if (!work_pending(&wm->pen_event_work)) {
-	queue_work(wm->ts_workq, &wm->pen_event_work);
+		wm->mach_ops->irq_enable(wm, 0);
+		queue_work(wm->ts_workq, &wm->pen_event_work);
+	}
 
 	return IRQ_HANDLED;
 }
@@ -355,7 +372,8 @@ static int wm97xx_init_pen_irq(struct wm97xx *wm)
 	 * provided. */
 	BUG_ON(!wm->mach_ops->irq_enable);
 
-	if (request_irq(wm->pen_irq, wm97xx_pen_interrupt, IRQF_SHARED,
+	if (request_irq(wm->pen_irq, wm97xx_pen_interrupt,
+			IRQF_SHARED | IRQF_SAMPLE_RANDOM,
 			"wm97xx-pen", wm)) {
 		dev_err(wm->dev,
 			"Failed to register pen down interrupt, polling");
@@ -688,10 +706,32 @@ static int wm97xx_remove(struct device *dev)
 static int wm97xx_suspend(struct device *dev, pm_message_t state)
 {
 	struct wm97xx *wm = dev_get_drvdata(dev);
+	u16 reg;
+	int suspend_mode;
+
+	if (device_may_wakeup(&wm->input_dev->dev))
+		suspend_mode = wm->suspend_mode;
+	else
+		suspend_mode = 0;
 
 	if (wm->input_dev->users)
 		cancel_delayed_work_sync(&wm->ts_reader);
 
+	/* Power down the digitiser (bypassing the cache for resume) */
+	reg = wm97xx_reg_read(wm, AC97_WM97XX_DIGITISER2);
+	reg &= ~WM97XX_PRP_DET_DIG;
+	if (wm->input_dev->users)
+		reg |= suspend_mode;
+	wm->ac97->bus->ops->write(wm->ac97, AC97_WM97XX_DIGITISER2, reg);
+
+	/* WM9713 has an additional power bit - turn it off if there
+	 * are no users or if suspend mode is zero. */
+	if (wm->id == WM9713_ID2 &&
+	    (!wm->input_dev->users || !suspend_mode)) {
+		reg = wm97xx_reg_read(wm, AC97_EXTENDED_MID) | 0x8000;
+		wm97xx_reg_write(wm, AC97_EXTENDED_MID, reg);
+	}
+
 	return 0;
 }
 

include/linux/wm97xx.h

@@ -282,6 +282,7 @@ struct wm97xx {
 	unsigned pen_is_down:1;		/* Pen is down */
 	unsigned aux_waiting:1;		/* aux measurement waiting */
 	unsigned pen_probably_down:1;	/* used in polling mode */
+	u16 suspend_mode;               /* PRP in suspend mode */
 };
 
 /*
@@ -297,6 +298,8 @@ void wm97xx_config_gpio(struct wm97xx *wm, u32 gpio,
 				     enum wm97xx_gpio_sticky sticky,
 				     enum wm97xx_gpio_wake wake);
 
+void wm97xx_set_suspend_mode(struct wm97xx *wm, u16 mode);
+
 /* codec AC97 IO access */
 int wm97xx_reg_read(struct wm97xx *wm, u16 reg);
 void wm97xx_reg_write(struct wm97xx *wm, u16 reg, u16 val);