[Blackfin] arch: initial generic time and clock sources
This patch enables Hight-Res Timers and tickless kernel Signed-off-by: Vitja Makarov <vitja.makarov@gmail.com> Signed-off-by: Michael Hennerich <michael.hennerich@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
This commit is contained in:
Vitja Makarov
Bryan Wu
parent
3dc5063786
commit
8b5f79f9d7
|
|
@ -47,10 +47,6 @@ config GENERIC_IRQ_PROBE
|
|||
bool
|
||||
default y
|
||||
|
||||
config GENERIC_TIME
|
||||
bool
|
||||
default n
|
||||
|
||||
config GENERIC_GPIO
|
||||
bool
|
||||
default y
|
||||
|
|
@ -415,6 +411,30 @@ comment "Kernel Timer/Scheduler"
|
|||
|
||||
source kernel/Kconfig.hz
|
||||
|
||||
config GENERIC_TIME
|
||||
bool "Generic time"
|
||||
default y
|
||||
|
||||
config GENERIC_CLOCKEVENTS
|
||||
bool "Generic clock events"
|
||||
depends on GENERIC_TIME
|
||||
default y
|
||||
|
||||
config CYCLES_CLOCKSOURCE
|
||||
bool "Use 'CYCLES' as a clocksource (EXPERIMENTAL)"
|
||||
depends on EXPERIMENTAL
|
||||
depends on GENERIC_CLOCKEVENTS
|
||||
depends on !BFIN_SCRATCH_REG_CYCLES
|
||||
default n
|
||||
help
|
||||
If you say Y here, you will enable support for using the 'cycles'
|
||||
registers as a clock source. Doing so means you will be unable to
|
||||
safely write to the 'cycles' register during runtime. You will
|
||||
still be able to read it (such as for performance monitoring), but
|
||||
writing the registers will most likely crash the kernel.
|
||||
|
||||
source kernel/time/Kconfig
|
||||
|
||||
comment "Memory Setup"
|
||||
|
||||
config MEM_SIZE
|
||||
|
|
|
|||
|
|
@ -6,9 +6,15 @@ extra-y := init_task.o vmlinux.lds
|
|||
|
||||
obj-y := \
|
||||
entry.o process.o bfin_ksyms.o ptrace.o setup.o signal.o \
|
||||
sys_bfin.o time.o traps.o irqchip.o dma-mapping.o flat.o \
|
||||
sys_bfin.o traps.o irqchip.o dma-mapping.o flat.o \
|
||||
fixed_code.o reboot.o bfin_gpio.o
|
||||
|
||||
ifeq ($(CONFIG_GENERIC_CLOCKEVENTS),y)
|
||||
obj-y += time-ts.o
|
||||
else
|
||||
obj-y += time.o
|
||||
endif
|
||||
|
||||
obj-$(CONFIG_BFIN_GPTIMERS) += gptimers.o
|
||||
obj-$(CONFIG_MODULES) += module.o
|
||||
obj-$(CONFIG_BFIN_DMA_5XX) += bfin_dma_5xx.o
|
||||
|
|
|
|||
|
|
@ -32,6 +32,8 @@
|
|||
#include <linux/unistd.h>
|
||||
#include <linux/user.h>
|
||||
#include <linux/uaccess.h>
|
||||
#include <linux/sched.h>
|
||||
#include <linux/tick.h>
|
||||
#include <linux/fs.h>
|
||||
#include <linux/err.h>
|
||||
|
||||
|
|
@ -69,33 +71,44 @@ EXPORT_SYMBOL(pm_power_off);
|
|||
* The idle loop on BFIN
|
||||
*/
|
||||
#ifdef CONFIG_IDLE_L1
|
||||
void default_idle(void)__attribute__((l1_text));
|
||||
static void default_idle(void)__attribute__((l1_text));
|
||||
void cpu_idle(void)__attribute__((l1_text));
|
||||
#endif
|
||||
|
||||
void default_idle(void)
|
||||
/*
|
||||
* This is our default idle handler. We need to disable
|
||||
* interrupts here to ensure we don't miss a wakeup call.
|
||||
*/
|
||||
static void default_idle(void)
|
||||
{
|
||||
while (!need_resched()) {
|
||||
local_irq_disable();
|
||||
if (likely(!need_resched()))
|
||||
if (!need_resched())
|
||||
idle_with_irq_disabled();
|
||||
|
||||
local_irq_enable();
|
||||
}
|
||||
}
|
||||
|
||||
void (*idle)(void) = default_idle;
|
||||
|
||||
/*
|
||||
* The idle thread. There's no useful work to be
|
||||
* done, so just try to conserve power and have a
|
||||
* low exit latency (ie sit in a loop waiting for
|
||||
* somebody to say that they'd like to reschedule)
|
||||
* The idle thread. We try to conserve power, while trying to keep
|
||||
* overall latency low. The architecture specific idle is passed
|
||||
* a value to indicate the level of "idleness" of the system.
|
||||
*/
|
||||
void cpu_idle(void)
|
||||
{
|
||||
/* endless idle loop with no priority at all */
|
||||
while (1) {
|
||||
void (*idle)(void) = pm_idle;
|
||||
|
||||
#ifdef CONFIG_HOTPLUG_CPU
|
||||
if (cpu_is_offline(smp_processor_id()))
|
||||
cpu_die();
|
||||
#endif
|
||||
if (!idle)
|
||||
idle = default_idle;
|
||||
tick_nohz_stop_sched_tick();
|
||||
while (!need_resched())
|
||||
idle();
|
||||
tick_nohz_restart_sched_tick();
|
||||
preempt_enable_no_resched();
|
||||
schedule();
|
||||
preempt_disable();
|
||||
|
|
|
|||
|
|
@ -0,0 +1,194 @@
|
|||
/*
|
||||
* linux/arch/kernel/time-ts.c
|
||||
*
|
||||
* Based on arm clockevents implementation and old bfin time tick.
|
||||
*
|
||||
* Copyright(C) 2008, GeoTechnologies, Vitja Makarov
|
||||
*
|
||||
* This code is licenced under the GPL version 2. For details see
|
||||
* kernel-base/COPYING.
|
||||
*/
|
||||
#include <linux/module.h>
|
||||
#include <linux/profile.h>
|
||||
#include <linux/interrupt.h>
|
||||
#include <linux/time.h>
|
||||
#include <linux/irq.h>
|
||||
#include <linux/clocksource.h>
|
||||
#include <linux/clockchips.h>
|
||||
|
||||
#include <asm/blackfin.h>
|
||||
|
||||
#ifdef CONFIG_CYCLES_CLOCKSOURCE
|
||||
|
||||
static unsigned long cyc2ns_scale;
|
||||
#define CYC2NS_SCALE_FACTOR 10 /* 2^10, carefully chosen */
|
||||
|
||||
static inline void set_cyc2ns_scale(unsigned long cpu_khz)
|
||||
{
|
||||
cyc2ns_scale = (1000000 << CYC2NS_SCALE_FACTOR) / cpu_khz;
|
||||
}
|
||||
|
||||
static inline unsigned long long cycles_2_ns(cycle_t cyc)
|
||||
{
|
||||
return (cyc * cyc2ns_scale) >> CYC2NS_SCALE_FACTOR;
|
||||
}
|
||||
|
||||
static cycle_t read_cycles(void)
|
||||
{
|
||||
unsigned long tmp, tmp2;
|
||||
asm("%0 = cycles; %1 = cycles2;" : "=d"(tmp), "=d"(tmp2));
|
||||
return tmp | ((cycle_t)tmp2 << 32);
|
||||
}
|
||||
|
||||
unsigned long long sched_clock(void)
|
||||
{
|
||||
return cycles_2_ns(read_cycles());
|
||||
}
|
||||
|
||||
static struct clocksource clocksource_bfin = {
|
||||
.name = "bfin_cycles",
|
||||
.rating = 350,
|
||||
.read = read_cycles,
|
||||
.mask = CLOCKSOURCE_MASK(64),
|
||||
.shift = 22,
|
||||
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
|
||||
};
|
||||
|
||||
static int __init bfin_clocksource_init(void)
|
||||
{
|
||||
set_cyc2ns_scale(get_cclk() / 1000);
|
||||
|
||||
clocksource_bfin.mult = clocksource_hz2mult(get_cclk(), clocksource_bfin.shift);
|
||||
|
||||
if (clocksource_register(&clocksource_bfin))
|
||||
panic("failed to register clocksource");
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#else
|
||||
# define bfin_clocksource_init()
|
||||
#endif
|
||||
|
||||
static int bfin_timer_set_next_event(unsigned long cycles,
|
||||
struct clock_event_device *evt)
|
||||
{
|
||||
bfin_write_TCOUNT(cycles);
|
||||
CSYNC();
|
||||
return 0;
|
||||
}
|
||||
|
||||
static void bfin_timer_set_mode(enum clock_event_mode mode,
|
||||
struct clock_event_device *evt)
|
||||
{
|
||||
switch (mode) {
|
||||
case CLOCK_EVT_MODE_PERIODIC: {
|
||||
unsigned long tcount = ((get_cclk() / (HZ * 1)) - 1);
|
||||
bfin_write_TCNTL(TMPWR);
|
||||
CSYNC();
|
||||
bfin_write_TPERIOD(tcount);
|
||||
bfin_write_TCOUNT(tcount);
|
||||
bfin_write_TCNTL(TMPWR | TMREN | TAUTORLD);
|
||||
CSYNC();
|
||||
break;
|
||||
}
|
||||
case CLOCK_EVT_MODE_ONESHOT:
|
||||
bfin_write_TCOUNT(0);
|
||||
bfin_write_TCNTL(TMPWR | TMREN);
|
||||
CSYNC();
|
||||
break;
|
||||
case CLOCK_EVT_MODE_UNUSED:
|
||||
case CLOCK_EVT_MODE_SHUTDOWN:
|
||||
bfin_write_TCNTL(0);
|
||||
CSYNC();
|
||||
break;
|
||||
case CLOCK_EVT_MODE_RESUME:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
static void __init bfin_timer_init(void)
|
||||
{
|
||||
/* power up the timer, but don't enable it just yet */
|
||||
bfin_write_TCNTL(TMPWR);
|
||||
CSYNC();
|
||||
|
||||
/*
|
||||
* the TSCALE prescaler counter.
|
||||
*/
|
||||
bfin_write_TSCALE(0);
|
||||
bfin_write_TPERIOD(0);
|
||||
bfin_write_TCOUNT(0);
|
||||
|
||||
/* now enable the timer */
|
||||
CSYNC();
|
||||
}
|
||||
|
||||
/*
|
||||
* timer_interrupt() needs to keep up the real-time clock,
|
||||
* as well as call the "do_timer()" routine every clocktick
|
||||
*/
|
||||
#ifdef CONFIG_CORE_TIMER_IRQ_L1
|
||||
__attribute__((l1_text))
|
||||
#endif
|
||||
irqreturn_t timer_interrupt(int irq, void *dev_id);
|
||||
|
||||
static struct clock_event_device clockevent_bfin = {
|
||||
.name = "bfin_core_timer",
|
||||
.features = CLOCK_EVT_FEAT_PERIODIC | CLOCK_EVT_FEAT_ONESHOT,
|
||||
.shift = 32,
|
||||
.cpumask = CPU_MASK_CPU0,
|
||||
.set_next_event = bfin_timer_set_next_event,
|
||||
.set_mode = bfin_timer_set_mode,
|
||||
};
|
||||
|
||||
static struct irqaction bfin_timer_irq = {
|
||||
.name = "Blackfin Core Timer",
|
||||
.flags = IRQF_DISABLED | IRQF_TIMER | IRQF_IRQPOLL,
|
||||
.handler = timer_interrupt,
|
||||
.dev_id = &clockevent_bfin,
|
||||
};
|
||||
|
||||
irqreturn_t timer_interrupt(int irq, void *dev_id)
|
||||
{
|
||||
struct clock_event_device *evt = dev_id;
|
||||
evt->event_handler(evt);
|
||||
return IRQ_HANDLED;
|
||||
}
|
||||
|
||||
static int __init bfin_clockevent_init(void)
|
||||
{
|
||||
setup_irq(IRQ_CORETMR, &bfin_timer_irq);
|
||||
bfin_timer_init();
|
||||
|
||||
clockevent_bfin.mult = div_sc(get_cclk(), NSEC_PER_SEC, clockevent_bfin.shift);
|
||||
clockevent_bfin.max_delta_ns = clockevent_delta2ns(-1, &clockevent_bfin);
|
||||
clockevent_bfin.min_delta_ns = clockevent_delta2ns(100, &clockevent_bfin);
|
||||
clockevents_register_device(&clockevent_bfin);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
void __init time_init(void)
|
||||
{
|
||||
time_t secs_since_1970 = (365 * 37 + 9) * 24 * 60 * 60; /* 1 Jan 2007 */
|
||||
|
||||
#ifdef CONFIG_RTC_DRV_BFIN
|
||||
/* [#2663] hack to filter junk RTC values that would cause
|
||||
* userspace to have to deal with time values greater than
|
||||
* 2^31 seconds (which uClibc cannot cope with yet)
|
||||
*/
|
||||
if ((bfin_read_RTC_STAT() & 0xC0000000) == 0xC0000000) {
|
||||
printk(KERN_NOTICE "bfin-rtc: invalid date; resetting\n");
|
||||
bfin_write_RTC_STAT(0);
|
||||
}
|
||||
#endif
|
||||
|
||||
/* Initialize xtime. From now on, xtime is updated with timer interrupts */
|
||||
xtime.tv_sec = secs_since_1970;
|
||||
xtime.tv_nsec = 0;
|
||||
set_normalized_timespec(&wall_to_monotonic, -xtime.tv_sec, -xtime.tv_nsec);
|
||||
|
||||
bfin_clocksource_init();
|
||||
bfin_clockevent_init();
|
||||
}
|
||||
Loading…
Reference in New Issue