From 1a93456d08b872d7b1679ccb7196b570609a16f4 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Thu, 19 Nov 2020 17:44:51 +0200 Subject: [PATCH 001/584] ARM: dts: am33xx-l4: add dt node for new cpsw switchdev driver Add DT node for the new cpsw switchdev based driver. Signed-off-by: Grygorii Strashko Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am33xx-l4.dtsi | 49 ++++++++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi index cb164dfec56d..cbc9309648ac 100644 --- a/arch/arm/boot/dts/am33xx-l4.dtsi +++ b/arch/arm/boot/dts/am33xx-l4.dtsi @@ -751,6 +751,55 @@ phys = <&phy_gmii_sel 2 1>; }; }; + + mac_sw: switch@0 { + compatible = "ti,am335x-cpsw-switch", "ti,cpsw-switch"; + reg = <0x0 0x4000>; + ranges = <0 0 0x4000>; + clocks = <&cpsw_125mhz_gclk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <1>; + syscon = <&scm_conf>; + status = "disabled"; + + interrupts = <40 41 42 43>; + interrupt-names = "rx_thresh", "rx", "tx", "misc"; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + cpsw_port1: port@1 { + reg = <1>; + label = "port1"; + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 1 1>; + }; + + cpsw_port2: port@2 { + reg = <2>; + label = "port2"; + mac-address = [ 00 00 00 00 00 00 ]; + phys = <&phy_gmii_sel 2 1>; + }; + }; + + davinci_mdio_sw: mdio@1000 { + compatible = "ti,cpsw-mdio","ti,davinci_mdio"; + clocks = <&cpsw_125mhz_gclk>; + clock-names = "fck"; + #address-cells = <1>; + #size-cells = <0>; + bus_freq = <1000000>; + reg = <0x1000 0x100>; + }; + + cpts { + clocks = <&cpsw_cpts_rft_clk>; + clock-names = "cpts"; + }; + }; }; target-module@180000 { /* 0x4a180000, ap 5 10.0 */ From f0d67d10b7c440782bcd58f74b3dce3a98f64ee0 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Thu, 19 Nov 2020 17:44:52 +0200 Subject: [PATCH 002/584] ARM: dts: am335x-evm/evmsk/icev2: switch to new cpsw switch drv The dual_mac mode has been preserved the same way between legacy and new driver, and one port devices works the same as 1 dual_mac port - it's safe to switch drivers. So, Switch amam335x-evm, am335x-evmsk and am335x-icev2 boards to use new cpsw switch driver. Those boards have or 2 Ext. port wired and configured in dual_mac mode by default, or only 1 Ext. port. Signed-off-by: Grygorii Strashko Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am335x-evm.dts | 13 ++++++++----- arch/arm/boot/dts/am335x-evmsk.dts | 14 ++++++-------- arch/arm/boot/dts/am335x-icev2.dts | 14 ++++++-------- 3 files changed, 20 insertions(+), 21 deletions(-) diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index 7c6f2c11f0e1..902e295b309e 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -684,28 +684,31 @@ }; }; -&mac { +&mac_sw { pinctrl-names = "default", "sleep"; pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; status = "okay"; - slaves = <1>; }; -&davinci_mdio { +&davinci_mdio_sw { pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; - status = "okay"; ethphy0: ethernet-phy@0 { reg = <0>; }; }; -&cpsw_emac0 { +&cpsw_port1 { phy-handle = <ðphy0>; phy-mode = "rgmii-id"; + ti,dual-emac-pvid = <1>; +}; + +&cpsw_port2 { + status = "disabled"; }; &tscadc { diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index b43b94122d3c..d5f8d5e2eb5d 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -596,19 +596,17 @@ }; }; -&mac { +&mac_sw { pinctrl-names = "default", "sleep"; pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; - dual_emac = <1>; status = "okay"; }; -&davinci_mdio { +&davinci_mdio_sw { pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; - status = "okay"; ethphy0: ethernet-phy@0 { reg = <0>; @@ -619,16 +617,16 @@ }; }; -&cpsw_emac0 { +&cpsw_port1 { phy-handle = <ðphy0>; phy-mode = "rgmii-id"; - dual_emac_res_vlan = <1>; + ti,dual-emac-pvid = <1>; }; -&cpsw_emac1 { +&cpsw_port2 { phy-handle = <ðphy1>; phy-mode = "rgmii-id"; - dual_emac_res_vlan = <2>; + ti,dual-emac-pvid = <2>; }; &mmc1 { diff --git a/arch/arm/boot/dts/am335x-icev2.dts b/arch/arm/boot/dts/am335x-icev2.dts index b958ab56a412..e923d065304d 100644 --- a/arch/arm/boot/dts/am335x-icev2.dts +++ b/arch/arm/boot/dts/am335x-icev2.dts @@ -474,31 +474,29 @@ }; }; -&cpsw_emac0 { +&cpsw_port1 { phy-handle = <ðphy0>; phy-mode = "rmii"; - dual_emac_res_vlan = <1>; + ti,dual-emac-pvid = <1>; }; -&cpsw_emac1 { +&cpsw_port2 { phy-handle = <ðphy1>; phy-mode = "rmii"; - dual_emac_res_vlan = <2>; + ti,dual-emac-pvid = <2>; }; -&mac { +&mac_sw { pinctrl-names = "default", "sleep"; pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; status = "okay"; - dual_emac; }; -&davinci_mdio { +&davinci_mdio_sw { pinctrl-names = "default", "sleep"; pinctrl-0 = <&davinci_mdio_default>; pinctrl-1 = <&davinci_mdio_sleep>; - status = "okay"; reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; reset-delay-us = <2>; /* PHY datasheet states 1uS min */ From e278f68cbf18917cbb5d1329f07c940951345090 Mon Sep 17 00:00:00 2001 From: Andreas Kemnade Date: Tue, 1 Dec 2020 08:46:28 +0100 Subject: [PATCH 003/584] ARM: dts: omap3-gta04: fix twl4030-power settings Things are wired up for powersaving, so lets use the corresponding compatible and also update a deprecated property name. Signed-off-by: Andreas Kemnade Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-gta04.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi index c8745bc800f7..cbe9ce739170 100644 --- a/arch/arm/boot/dts/omap3-gta04.dtsi +++ b/arch/arm/boot/dts/omap3-gta04.dtsi @@ -489,8 +489,8 @@ }; twl_power: power { - compatible = "ti,twl4030-power"; - ti,use_poweroff; + compatible = "ti,twl4030-power-idle"; + ti,system-power-controller; }; }; }; From 7a8633c4551f5064d7e4460c8ef92373f21530f2 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 7 Dec 2020 16:33:37 +0200 Subject: [PATCH 004/584] ARM: dts: am574x-idk: add support for EMIF1 ECC EMIF1 has ECC support, so add the DT node with address and interrupt details to handle this. Signed-off-by: Tero Kristo Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am574x-idk.dts | 4 ++++ arch/arm/boot/dts/dra76x.dtsi | 7 +++++++ 2 files changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts index 37758761cd88..1b8f3a28af05 100644 --- a/arch/arm/boot/dts/am574x-idk.dts +++ b/arch/arm/boot/dts/am574x-idk.dts @@ -39,3 +39,7 @@ &m_can0 { status = "disabled"; }; + +&emif1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/dra76x.dtsi b/arch/arm/boot/dts/dra76x.dtsi index b69c7d40f5d8..4a2840c0b6ad 100644 --- a/arch/arm/boot/dts/dra76x.dtsi +++ b/arch/arm/boot/dts/dra76x.dtsi @@ -9,6 +9,13 @@ compatible = "ti,dra762", "ti,dra7"; ocp { + emif1: emif@4c000000 { + compatible = "ti,emif-dra7xx"; + reg = <0x4c000000 0x200>; + interrupts = ; + status = "disabled"; + }; + target-module@42c01900 { compatible = "ti,sysc-dra7-mcan", "ti,sysc"; ranges = <0x0 0x42c00000 0x2000>; From 685a7807421864f1b0a328bbe84c994de1139605 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 7 Dec 2020 16:33:38 +0200 Subject: [PATCH 005/584] ARM: dts: dra76x: add support for OPP_PLUS Add support for the OPP_PLUS (1.8GHz) for MPU. Signed-off-by: Tero Kristo Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra76x.dtsi | 29 +++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+) diff --git a/arch/arm/boot/dts/dra76x.dtsi b/arch/arm/boot/dts/dra76x.dtsi index 4a2840c0b6ad..c62c83a1e298 100644 --- a/arch/arm/boot/dts/dra76x.dtsi +++ b/arch/arm/boot/dts/dra76x.dtsi @@ -140,3 +140,32 @@ /* dra76x is not affected by i887 */ max-frequency = <96000000>; }; + +&cpu0_opp_table { + opp_plus@1800000000 { + opp-hz = /bits/ 64 <1800000000>; + opp-microvolt = <1250000 950000 1250000>, + <1250000 950000 1250000>; + opp-supported-hw = <0xFF 0x08>; + }; +}; + +&opp_supply_mpu { + ti,efuse-settings = < + /* uV offset */ + 1060000 0x0 + 1160000 0x4 + 1210000 0x8 + 1250000 0xC + >; +}; + +&abb_mpu { + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1060000 0 0x0 0 0x02000000 0x01F00000 + 1160000 0 0x4 0 0x02000000 0x01F00000 + 1210000 0 0x8 0 0x02000000 0x01F00000 + 1250000 0 0xC 0 0x02000000 0x01F00000 + >; +}; From 4d4ce69f19d4991701e84d5eaa0fc0e506210042 Mon Sep 17 00:00:00 2001 From: Tero Kristo Date: Mon, 7 Dec 2020 16:33:39 +0200 Subject: [PATCH 006/584] ARM: dts: dra71-evm: mark ldo0 regulator as always on LDO0 regulator must remain enabled always on dra71-evm boards. Disabling this violates the data manual and will damage the device over time. Reported-by: Brad Griffis Signed-off-by: Tero Kristo Reviewed-by: Keerthy Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra71-evm.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts index cad58f733bd6..6d2cca6b4488 100644 --- a/arch/arm/boot/dts/dra71-evm.dts +++ b/arch/arm/boot/dts/dra71-evm.dts @@ -112,6 +112,8 @@ regulator-name = "lp8733-ldo0"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; }; lp8733_ldo1_reg: ldo1 { From b4385b5620b290729170974156fb8afb0fc1c454 Mon Sep 17 00:00:00 2001 From: Alexander Dahl Date: Sat, 28 Nov 2020 22:53:50 +0100 Subject: [PATCH 007/584] ARM: dts: berlin: Fix schema warnings for pwm-leds The node names for devices using the pwm-leds driver follow a certain naming scheme (now). Parent node name is not enforced, but recommended by DT project. DTC arch/arm/boot/dts/berlin2cd-google-chromecast.dt.yaml CHECK arch/arm/boot/dts/berlin2cd-google-chromecast.dt.yaml /home/alex/build/linux/arch/arm/boot/dts/berlin2cd-google-chromecast.dt.yaml: leds: 'red', 'white' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+' From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml Signed-off-by: Alexander Dahl Signed-off-by: Jisheng Zhang --- arch/arm/boot/dts/berlin2cd-google-chromecast.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts index 56fa951bc86f..c1d91424e658 100644 --- a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts +++ b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts @@ -34,19 +34,19 @@ linux,usable-memory = <0x00000000 0x20000000>; /* 512 MB */ }; - leds { + led-controller { compatible = "pwm-leds"; pinctrl-0 = <&ledpwm_pmux>; pinctrl-names = "default"; - white { + led-1 { label = "white"; pwms = <&pwm 0 600000 0>; max-brightness = <255>; linux,default-trigger = "default-on"; }; - red { + led-2 { label = "red"; pwms = <&pwm 1 600000 0>; max-brightness = <255>; From 7706e376f5311487099f5243875bf608347c915f Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 9 Nov 2020 16:54:16 +0800 Subject: [PATCH 008/584] ARM: dts: berlin: Use generic "ngpios" rather than "snps,nr-gpios" This is to remove similar errors as below: OF: /.../gpio-port@0: could not find phandle Commit 7569486d79ae ("gpio: dwapb: Add ngpios DT-property support") explained the reason of above errors well and added the generic "ngpios" property, let's use it. Signed-off-by: Jisheng Zhang Reviewed-by: Linus Walleij --- arch/arm/boot/dts/berlin2.dtsi | 12 ++++++------ arch/arm/boot/dts/berlin2cd.dtsi | 12 ++++++------ arch/arm/boot/dts/berlin2q.dtsi | 12 ++++++------ 3 files changed, 18 insertions(+), 18 deletions(-) diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi index 6194857f8a02..1114c592e461 100644 --- a/arch/arm/boot/dts/berlin2.dtsi +++ b/arch/arm/boot/dts/berlin2.dtsi @@ -191,7 +191,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -209,7 +209,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -227,7 +227,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -245,7 +245,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -446,7 +446,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; }; }; @@ -461,7 +461,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/berlin2cd.dtsi b/arch/arm/boot/dts/berlin2cd.dtsi index 6f30d7eb3b41..b2768f7a3185 100644 --- a/arch/arm/boot/dts/berlin2cd.dtsi +++ b/arch/arm/boot/dts/berlin2cd.dtsi @@ -181,7 +181,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -199,7 +199,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -217,7 +217,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -235,7 +235,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -473,7 +473,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; }; }; @@ -518,7 +518,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <8>; + ngpios = <8>; reg = <0>; }; }; diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi index b6a0acac6836..598a46f96a82 100644 --- a/arch/arm/boot/dts/berlin2q.dtsi +++ b/arch/arm/boot/dts/berlin2q.dtsi @@ -252,7 +252,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -270,7 +270,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -288,7 +288,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -306,7 +306,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -552,7 +552,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; }; }; @@ -613,7 +613,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; }; }; From ec13e5027261c7a09e70b309050a858076bae5a0 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 9 Nov 2020 16:49:55 +0800 Subject: [PATCH 009/584] arm64: dts: synaptics: Use generic "ngpios" rather than "snps,nr-gpios" This is to remove similar errors as below: OF: /.../gpio-port@0: could not find phandle Commit 7569486d79ae ("gpio: dwapb: Add ngpios DT-property support") explained the reason of above errors well and added the generic "ngpios" property, let's use it. Signed-off-by: Jisheng Zhang --- arch/arm64/boot/dts/synaptics/as370.dtsi | 4 ++-- arch/arm64/boot/dts/synaptics/berlin4ct.dtsi | 12 ++++++------ 2 files changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/synaptics/as370.dtsi b/arch/arm64/boot/dts/synaptics/as370.dtsi index addeb0efc616..4bb5d650df9c 100644 --- a/arch/arm64/boot/dts/synaptics/as370.dtsi +++ b/arch/arm64/boot/dts/synaptics/as370.dtsi @@ -143,7 +143,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -161,7 +161,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi b/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi index 15625b99e336..0949acee4728 100644 --- a/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi +++ b/arch/arm64/boot/dts/synaptics/berlin4ct.dtsi @@ -140,7 +140,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -158,7 +158,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -176,7 +176,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -194,7 +194,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -269,7 +269,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; }; }; @@ -284,7 +284,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <32>; + ngpios = <32>; reg = <0>; }; }; From 23e85be1ec81647374055f731488cc9a7c013a5c Mon Sep 17 00:00:00 2001 From: Michael Klein Date: Mon, 30 Nov 2020 19:38:43 +0100 Subject: [PATCH 010/584] ARM: dts: sun8i-h2-plus-bananapi-m2-zero: add regulator nodes vcc-dram and vcc1v2 Add regulator nodes vcc-dram and vcc1v2 to the devicetree. These regulators correspond to U4 and U5 in the schematics: http://forum.banana-pi.org/t/bpi-m2-zero-schematic-diagram-public/4111 Signed-off-by: Michael Klein Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201130183841.136708-1-michael@fossekall.de --- .../dts/sun8i-h2-plus-bananapi-m2-zero.dts | 24 +++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts index e76d56a3df9c..b43028f9e6df 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -62,6 +62,30 @@ states = <1100000 0>, <1300000 1>; }; + reg_vcc_dram: vcc-dram { + compatible = "regulator-fixed"; + regulator-name = "vcc-dram"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 9 GPIO_ACTIVE_HIGH>; /* PL9 */ + vin-supply = <®_vcc5v0>; + }; + + reg_vcc1v2: vcc1v2 { + compatible = "regulator-fixed"; + regulator-name = "vcc1v2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&r_pio 0 8 GPIO_ACTIVE_HIGH>; /* PL8 */ + vin-supply = <®_vcc5v0>; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ From 0d2a7e15d7912aa27dd3366f75d181b5141ca9a2 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:56 -0600 Subject: [PATCH 011/584] dt-bindings: arm: renesas: Add Beacon RZ/G2N and RZ/G2H boards Add beacon,beacon-rzg2n and beacon,beacon-rzg2h to the bindings list. Signed-off-by: Adam Ford Acked-by: Rob Herring Link: https://lore.kernel.org/r/20201213183759.223246-17-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- Documentation/devicetree/bindings/arm/renesas.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/renesas.yaml b/Documentation/devicetree/bindings/arm/renesas.yaml index fe11be65039a..5fd0696a9f91 100644 --- a/Documentation/devicetree/bindings/arm/renesas.yaml +++ b/Documentation/devicetree/bindings/arm/renesas.yaml @@ -130,6 +130,7 @@ properties: - description: RZ/G2N (R8A774B1) items: - enum: + - beacon,beacon-rzg2n # Beacon EmbeddedWorks RZ/G2N Kit - hoperun,hihope-rzg2n # HopeRun HiHope RZ/G2N platform - const: renesas,r8a774b1 @@ -154,6 +155,7 @@ properties: - description: RZ/G2H (R8A774E1) items: - enum: + - beacon,beacon-rzg2h # Beacon EmbeddedWorks RZ/G2H Kit - hoperun,hihope-rzg2h # HopeRun HiHope RZ/G2H platform - const: renesas,r8a774e1 From 5edf8bd6f4a225f7ad0501f921f9717df152e7fb Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Niklas=20S=C3=B6derlund?= Date: Wed, 9 Dec 2020 21:07:37 +0100 Subject: [PATCH 012/584] arm64: dts: renesas: rcar-gen3: Add missing CMT nodes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add device nodes for the Compare Match Timer (CMT) on the Renesas R-Car M3-W+ (r8a77961) and D3 (r8a77995) SoCs. Signed-off-by: Niklas Söderlund Link: https://lore.kernel.org/r/20201209200738.811173-2-niklas.soderlund+renesas@ragnatech.se [geert: squashed two commits] Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a77961.dtsi | 70 +++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77995.dtsi | 70 +++++++++++++++++++++++ 2 files changed, 140 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi index 4b737c616257..4b5b242d5b25 100644 --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi @@ -453,6 +453,76 @@ reg = <0 0xe6060000 0 0x50c>; }; + cmt0: timer@e60f0000 { + compatible = "renesas,r8a77961-cmt0", + "renesas,rcar-gen3-cmt0"; + reg = <0 0xe60f0000 0 0x1004>; + interrupts = , + ; + clocks = <&cpg CPG_MOD 303>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 303>; + status = "disabled"; + }; + + cmt1: timer@e6130000 { + compatible = "renesas,r8a77961-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6130000 0 0x1004>; + interrupts = , + , + , + , + , + , + , + ; + clocks = <&cpg CPG_MOD 302>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 302>; + status = "disabled"; + }; + + cmt2: timer@e6140000 { + compatible = "renesas,r8a77961-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6140000 0 0x1004>; + interrupts = , + , + , + , + , + , + , + ; + clocks = <&cpg CPG_MOD 301>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 301>; + status = "disabled"; + }; + + cmt3: timer@e6148000 { + compatible = "renesas,r8a77961-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6148000 0 0x1004>; + interrupts = , + , + , + , + , + , + , + ; + clocks = <&cpg CPG_MOD 300>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 300>; + status = "disabled"; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a77961-cpg-mssr"; reg = <0 0xe6150000 0 0x1000>; diff --git a/arch/arm64/boot/dts/renesas/r8a77995.dtsi b/arch/arm64/boot/dts/renesas/r8a77995.dtsi index e1af7c4782f4..aca0b2d015cf 100644 --- a/arch/arm64/boot/dts/renesas/r8a77995.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77995.dtsi @@ -193,6 +193,76 @@ reg = <0 0xe6060000 0 0x508>; }; + cmt0: timer@e60f0000 { + compatible = "renesas,r8a77995-cmt0", + "renesas,rcar-gen3-cmt0"; + reg = <0 0xe60f0000 0 0x1004>; + interrupts = , + ; + clocks = <&cpg CPG_MOD 303>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 303>; + status = "disabled"; + }; + + cmt1: timer@e6130000 { + compatible = "renesas,r8a77995-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6130000 0 0x1004>; + interrupts = , + , + , + , + , + , + , + ; + clocks = <&cpg CPG_MOD 302>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 302>; + status = "disabled"; + }; + + cmt2: timer@e6140000 { + compatible = "renesas,r8a77995-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6140000 0 0x1004>; + interrupts = , + , + , + , + , + , + , + ; + clocks = <&cpg CPG_MOD 301>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 301>; + status = "disabled"; + }; + + cmt3: timer@e6148000 { + compatible = "renesas,r8a77995-cmt1", + "renesas,rcar-gen3-cmt1"; + reg = <0 0xe6148000 0 0x1004>; + interrupts = , + , + , + , + , + , + , + ; + clocks = <&cpg CPG_MOD 300>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 300>; + status = "disabled"; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a77995-cpg-mssr"; reg = <0 0xe6150000 0 0x1000>; From 4e4c17c6c3907dfc34051cc450a78a38fb371b4f Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Niklas=20S=C3=B6derlund?= Date: Thu, 10 Dec 2020 16:27:00 +0100 Subject: [PATCH 013/584] arm64: dts: renesas: rcar-gen3: Add missing TMU nodes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Add device nodes for the Timer Unit (TMU) on the Renesas R-Car H3 (r8a77951), M3-W (r8a77960), M3-W+ (r8a77961), M3-N (r8a77965), E3 (r8a77990), and D3 (r8a77995) SoCs. Signed-off-by: Niklas Söderlund Link: https://lore.kernel.org/r/20201210152705.1535156-2-niklas.soderlund+renesas@ragnatech.se [geert: squashed six commits] Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a77951.dtsi | 65 +++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77960.dtsi | 65 +++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77961.dtsi | 65 +++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77965.dtsi | 65 +++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77990.dtsi | 65 +++++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77995.dtsi | 65 +++++++++++++++++++++++ 6 files changed, 390 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a77951.dtsi b/arch/arm64/boot/dts/renesas/r8a77951.dtsi index 9d60bcf69e4f..5c39152e4570 100644 --- a/arch/arm64/boot/dts/renesas/r8a77951.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77951.dtsi @@ -616,6 +616,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a7795", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A7795_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77960.dtsi b/arch/arm64/boot/dts/renesas/r8a77960.dtsi index 53b9aa26c9b1..25d947a81b29 100644 --- a/arch/arm64/boot/dts/renesas/r8a77960.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77960.dtsi @@ -585,6 +585,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a7796", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A7796_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi index 4b5b242d5b25..e8c31ebec097 100644 --- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi @@ -565,6 +565,71 @@ /* placeholder */ }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77961", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77961_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi index 4a913df17b1d..657b20d3533b 100644 --- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi @@ -455,6 +455,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77965", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77965_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77990.dtsi b/arch/arm64/boot/dts/renesas/r8a77990.dtsi index 87d41bc076a9..5010f23fafcc 100644 --- a/arch/arm64/boot/dts/renesas/r8a77990.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77990.dtsi @@ -420,6 +420,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77990", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77990_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a77995.dtsi b/arch/arm64/boot/dts/renesas/r8a77995.dtsi index aca0b2d015cf..2319271c881b 100644 --- a/arch/arm64/boot/dts/renesas/r8a77995.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a77995.dtsi @@ -312,6 +312,71 @@ resets = <&cpg 407>; }; + tmu0: timer@e61e0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe61e0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 125>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 125>; + status = "disabled"; + }; + + tmu1: timer@e6fc0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe6fc0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 124>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 124>; + status = "disabled"; + }; + + tmu2: timer@e6fd0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe6fd0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 123>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 123>; + status = "disabled"; + }; + + tmu3: timer@e6fe0000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xe6fe0000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 122>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 122>; + status = "disabled"; + }; + + tmu4: timer@ffc00000 { + compatible = "renesas,tmu-r8a77995", "renesas,tmu"; + reg = <0 0xffc00000 0 0x30>; + interrupts = , + , + ; + clocks = <&cpg CPG_MOD 121>; + clock-names = "fck"; + power-domains = <&sysc R8A77995_PD_ALWAYS_ON>; + resets = <&cpg 121>; + status = "disabled"; + }; + i2c0: i2c@e6500000 { #address-cells = <1>; #size-cells = <0>; From db030c5a9658846a42fbed4d43a8b5f28a2d7ab7 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:42 -0600 Subject: [PATCH 014/584] arm64: dts: renesas: beacon kit: Fix choppy Bluetooth Audio The Bluetooth chip is capable of operating at 4Mbps, but the max-speed setting was on the UART node instead of the Bluetooth node, so the chip didn't operate at the correct speed resulting in choppy audio. Fix this by setting the max-speed in the proper node. Fixes: a1d8a344f1ca ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit") Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-3-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index 8ac167aa18f0..b93219a95afc 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -89,7 +89,6 @@ pinctrl-names = "default"; uart-has-rtscts; status = "okay"; - max-speed = <4000000>; bluetooth { compatible = "brcm,bcm43438-bt"; @@ -98,6 +97,7 @@ device-wakeup-gpios = <&pca9654 5 GPIO_ACTIVE_HIGH>; clocks = <&osc_32k>; clock-names = "extclk"; + max-speed = <4000000>; }; }; From ac817b5a084dc8005266a748de33eedcbb772e04 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:43 -0600 Subject: [PATCH 015/584] arm64: dts: renesas: beacon kit: Remove unnecessary nodes VSPI0 and VSPB are already enabled by default. There is no need to add extra nodes to enable them. Remove the redundant nodes. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-4-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi | 8 -------- 1 file changed, 8 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index b93219a95afc..2a5e95ec9965 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -303,11 +303,3 @@ &usb3s0_clk { clock-frequency = <100000000>; }; - -&vspb { - status = "okay"; -}; - -&vspi0 { - status = "okay"; -}; From 5a5da0b758b327b727c5392d7f11e046e113a195 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:45 -0600 Subject: [PATCH 016/584] arm64: dts: renesas: beacon: Fix audio-1.8V pin enable The fact the audio worked at all was a coincidence because the wrong gpio enable was used. Use the correct GPIO pin to ensure its operation. Fixes: a1d8a344f1ca ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit") Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-6-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index e66b5b36e489..759734b7715b 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -150,7 +150,7 @@ regulator-name = "audio-1.8V"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - gpio = <&gpio_exp2 7 GPIO_ACTIVE_HIGH>; + gpio = <&gpio_exp4 1 GPIO_ACTIVE_HIGH>; enable-active-high; }; From 012f3e37ca134da45af742a2d7971c513cb761d9 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:47 -0600 Subject: [PATCH 017/584] arm64: dts: renesas: beacon: Fix LVDS PWM Backlight The backlight didn't really work correctly due to some updates that were made in hardware. It should be safe to apply these, because the older hardware was never shipped to anyone, so it shouldn't break anything. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-8-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- .../boot/dts/renesas/beacon-renesom-baseboard.dtsi | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index 759734b7715b..12a9f1434983 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -10,8 +10,8 @@ backlight_lvds: backlight-lvds { compatible = "pwm-backlight"; power-supply = <®_lcd>; - enable-gpios = <&gpio_exp1 3 GPIO_ACTIVE_LOW>; - pwms = <&pwm2 0 50000>; + enable-gpios = <&gpio_exp1 3 GPIO_ACTIVE_HIGH>; + pwms = <&pwm2 0 25000>; brightness-levels = <0 4 8 16 32 64 128 255>; default-brightness-level = <6>; }; @@ -118,9 +118,9 @@ hback-porch = <40>; vfront-porch = <13>; vback-porch = <29>; - vsync-len = <3>; + vsync-len = <1>; hsync-active = <1>; - vsync-active = <1>; + vsync-active = <3>; de-active = <1>; pixelclk-active = <0>; }; @@ -541,7 +541,7 @@ pwm2_pins: pwm2 { groups = "pwm2_a"; - function = "pwm2_a"; + function = "pwm2"; }; sdhi0_pins: sd0 { From 7f1cb1579808f97bd211b4ad16c82f2dc191c709 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:49 -0600 Subject: [PATCH 018/584] arm64: dts: renesas: beacon: Fix RGB Display PWM Backlight The backlight didn't really work correctly due to some updates that were made in hardware. It should be safe to apply these, because the older hardware was never shipped to anyone, so it shouldn't break anything. Because the display driver refers to the display as DPI, this also renames the backlight to use DPI for consistency. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-10-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index 12a9f1434983..1ab96ecc842b 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -16,12 +16,12 @@ default-brightness-level = <6>; }; - backlight_rgb: backlight-rgb { + backlight_dpi: backlight-dpi { compatible = "pwm-backlight"; power-supply = <®_lcd>; enable-gpios = <&gpio_exp1 7 GPIO_ACTIVE_LOW>; - pwms = <&pwm0 0 50000>; - brightness-levels = <0 4 8 16 32 64 128 255>; + pwms = <&pwm0 0 25000>; + brightness-levels = <0 25 33 50 63 75 88 100>; default-brightness-level = <6>; }; @@ -135,7 +135,7 @@ rgb { /* Different LCD with compatible timings */ compatible = "rocktech,rk070er9427"; - backlight = <&backlight_rgb>; + backlight = <&backlight_dpi>; enable-gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; power-supply = <®_lcd>; port { From a48f3c13689c65bcf4e7ff1b6a974beeeb9f48e5 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:50 -0600 Subject: [PATCH 019/584] arm64: dts: renesas: beacon: Don't make vccq_sdhi0 always on vccq_sdhi0 is referenced from sdhi0, so there is no need to force this regulator to be always-on. In theory it could help with low power modes in the future. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-11-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi | 3 --- 1 file changed, 3 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index 1ab96ecc842b..987df78ec44e 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -200,15 +200,12 @@ vccq_sdhi0: regulator-vccq-sdhi0 { compatible = "regulator-gpio"; - regulator-name = "SDHI0 VccQ"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; - gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; gpios-states = <1>; states = <3300000 1>, <1800000 0>; - regulator-always-on; }; /* External DU dot clocks */ From 7e0fac6a0da54557230ac3898688f37392404cdf Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:53 -0600 Subject: [PATCH 020/584] arm64: dts: renesas: beacon: Enable SPI The baseboard routes the SPI to a header which can/will be configured at either the kit level or using device tree overlays. Because the baseboard be supporting more than one kit, enable at the baseboard level rather than a bunch of duplicates later. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-14-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- .../boot/dts/renesas/beacon-renesom-baseboard.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index 987df78ec44e..cb316e736364 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -478,6 +478,13 @@ }; }; +&msiof1 { + pinctrl-0 = <&msiof1_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&gpio3 10 GPIO_ACTIVE_LOW>; +}; + &ohci0 { dr_mode = "otg"; status = "okay"; @@ -531,6 +538,11 @@ bias-pull-down; }; + msiof1_pins: msiof1 { + groups = "msiof1_clk_g", "msiof1_rxd_g", "msiof1_txd_g"; + function = "msiof1"; + }; + pwm0_pins: pwm0 { groups = "pwm0"; function = "pwm0"; From 900d9fc3becefd050bf54c1b98e368ce6463580e Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 13 Dec 2020 12:37:54 -0600 Subject: [PATCH 021/584] arm64: dts: renesas: beacon: Correct I2C bus speeds For greater compatibility with upcoming kits that will reuse the baseboard and SOM-level files, adjust the I2C speeds to make it the most compatible with all devices. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201213183759.223246-15-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi | 2 +- arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index cb316e736364..9db120ccb58d 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -339,7 +339,7 @@ &i2c2 { status = "okay"; - clock-frequency = <100000>; + clock-frequency = <400000>; pinctrl-0 = <&i2c2_pins>; pinctrl-names = "default"; diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index 2a5e95ec9965..b475de38ace8 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -109,7 +109,7 @@ &i2c4 { status = "okay"; - clock-frequency = <400000>; + clock-frequency = <100000>; pca9654: gpio@20 { compatible = "onnn,pca9654"; From f4b30c0a03a9edb3e70cbd7abe65fc6c3033fb20 Mon Sep 17 00:00:00 2001 From: Hoang Vo Date: Fri, 18 Dec 2020 18:37:28 +0100 Subject: [PATCH 022/584] arm64: dts: renesas: r8a779a0: Add RWDT node Add a device node for the Watchdog Timer (WDT) controller on the R8A779A0 SoC. Signed-off-by: Hoang Vo [wsa: rebased to mainline] Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20201218173731.12839-4-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 6cf77ce9aa93..f951e6b6f696 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -70,6 +70,16 @@ #size-cells = <2>; ranges; + rwdt: watchdog@e6020000 { + compatible = "renesas,r8a779a0-wdt", + "renesas,rcar-gen3-wdt"; + reg = <0 0xe6020000 0 0x0c>; + clocks = <&cpg CPG_MOD 907>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 907>; + status = "disabled"; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a779a0-cpg-mssr"; reg = <0 0xe6150000 0 0x4000>; From d207dc500bbcf8c6e1cbad375b08904f984f9602 Mon Sep 17 00:00:00 2001 From: Hoang Vo Date: Fri, 18 Dec 2020 18:37:29 +0100 Subject: [PATCH 023/584] arm64: dts: renesas: falcon: Enable watchdog timer Enable the watchdog on the Falcon board. Signed-off-by: Hoang Vo [wsa: rebased to mainline] Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20201218173731.12839-5-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts index 8eda70e5a82b..fb9978ea18f4 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts @@ -20,3 +20,8 @@ stdout-path = "serial0:115200n8"; }; }; + +&rwdt { + timeout-sec = <60>; + status = "okay"; +}; From 0085a33a25cc534838f801d697f87725e835743c Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 30 Nov 2020 15:09:22 +0530 Subject: [PATCH 024/584] arm64: dts: qcom: sm8250: Add support for LLCC block Add support for Last Level Cache Controller (LLCC) in SM8250 SoC. This LLCC is used to provide common cache memory pool for the cores in the SM8250 SoC thereby minimizing the percore caches. Reviewed-by: Sai Prakash Ranjan Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20201130093924.45057-3-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 65acd1f381eb..118b6bb29ebc 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1758,6 +1758,12 @@ }; }; + system-cache-controller@9200000 { + compatible = "qcom,sm8250-llcc"; + reg = <0 0x09200000 0 0x1d0000>, <0 0x09600000 0 0x50000>; + reg-names = "llcc_base", "llcc_broadcast_base"; + }; + usb_2: usb@a8f8800 { compatible = "qcom,sm8250-dwc3", "qcom,dwc3"; reg = <0 0x0a8f8800 0 0x400>; From 221f0ef37f5529fe35110651452f9c05dcb7bf8e Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Fri, 27 Nov 2020 12:26:46 +0300 Subject: [PATCH 025/584] arm64: dts: sm8250-mtp: enable USB host nodes Enable both USB host controller, hsphy and qmpphy nodes on sm8250. Add missing pm8150 ldo18 definition (used by USB qmp phys). Both controllers are locked to host mode: dual role on first controller is not enabled. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201127092646.122663-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 53 +++++++++++++++++++++++++ 1 file changed, 53 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts index dea00f19711d..3aac17604ff0 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts @@ -186,6 +186,13 @@ regulator-max-microvolt = <3008000>; regulator-initial-mode = ; }; + + vreg_l18a_0p9: ldo18 { + regulator-name = "vreg_l18a_0p9"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <912000>; + regulator-initial-mode = ; + }; }; pm8150l-rpmh-regulators { @@ -426,3 +433,49 @@ vdda-pll-supply = <&vreg_l9a_1p2>; vdda-pll-max-microamp = <19000>; }; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5a_0p875>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l2a_3p1>; +}; + +&usb_1_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l9a_1p2>; + vdda-pll-supply = <&vreg_l18a_0p9>; +}; + +&usb_2 { + status = "okay"; +}; + +&usb_2_dwc3 { + dr_mode = "host"; +}; + +&usb_2_hsphy { + status = "okay"; + + vdda-pll-supply = <&vreg_l5a_0p875>; + vdda18-supply = <&vreg_l12a_1p8>; + vdda33-supply = <&vreg_l2a_3p1>; +}; + +&usb_2_qmpphy { + status = "okay"; + + vdda-phy-supply = <&vreg_l9a_1p2>; + vdda-pll-supply = <&vreg_l18a_0p9>; +}; From 7c1dffd471b14dbf738268c7c0b3e43b362fa5db Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:20:59 +0300 Subject: [PATCH 026/584] arm64: dts: qcom: sm8250.dtsi: add display system nodes Add device tree nodes for mdss, mdp, dsi0/1. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-2-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 302 ++++++++++++++++++++++++++- 1 file changed, 295 insertions(+), 7 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 118b6bb29ebc..827197f83f4f 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -4,10 +4,12 @@ */ #include +#include #include #include #include #include +#include #include #include #include @@ -1254,14 +1256,8 @@ }; gpu: gpu@3d00000 { - /* - * note: the amd,imageon compatible makes it possible - * to use the drm/msm driver without the display node, - * make sure to remove it when display node is added - */ compatible = "qcom,adreno-650.2", - "qcom,adreno", - "amd,imageon"; + "qcom,adreno"; #stream-id-cells = <16>; reg = <0 0x03d00000 0 0x40000>; @@ -1809,6 +1805,298 @@ }; }; + mdss: mdss@ae00000 { + compatible = "qcom,sdm845-mdss"; + reg = <0 0x0ae00000 0 0x1000>; + reg-names = "mdss"; + + interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_DISPLAY_CFG>, + <&mmss_noc MASTER_MDP_PORT0 &mc_virt SLAVE_EBI_CH0>, + <&mmss_noc MASTER_MDP_PORT1 &mc_virt SLAVE_EBI_CH0>; + interconnect-names = "notused", "mdp0-mem", "mdp1-mem"; + + power-domains = <&dispcc MDSS_GDSC>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&gcc GCC_DISP_SF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>; + clock-names = "iface", "bus", "nrt_bus", "core"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>; + assigned-clock-rates = <460000000>; + + interrupts = ; + interrupt-controller; + #interrupt-cells = <1>; + + iommus = <&apps_smmu 0x820 0x402>; + + status = "disabled"; + + #address-cells = <2>; + #size-cells = <2>; + ranges; + + mdss_mdp: mdp@ae01000 { + compatible = "qcom,sdm845-dpu"; + reg = <0 0x0ae01000 0 0x8f000>, + <0 0x0aeb0000 0 0x2008>; + reg-names = "mdp", "vbif"; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>, + <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + clock-names = "iface", "bus", "core", "vsync"; + + assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>, + <&dispcc DISP_CC_MDSS_VSYNC_CLK>; + assigned-clock-rates = <460000000>, + <19200000>; + + operating-points-v2 = <&mdp_opp_table>; + power-domains = <&rpmhpd SM8250_MMCX>; + + interrupt-parent = <&mdss>; + interrupts = <0 IRQ_TYPE_LEVEL_HIGH>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf1_out: endpoint { + remote-endpoint = <&dsi0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf2_out: endpoint { + remote-endpoint = <&dsi1_in>; + }; + }; + }; + + mdp_opp_table: mdp-opp-table { + compatible = "operating-points-v2"; + + opp-200000000 { + opp-hz = /bits/ 64 <200000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-345000000 { + opp-hz = /bits/ 64 <345000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-460000000 { + opp-hz = /bits/ 64 <460000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + dsi0: dsi@ae94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae94000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, + <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK0_CLK>, + <&dispcc DISP_CC_MDSS_ESC0_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8250_MMCX>; + + phys = <&dsi0_phy>; + phy-names = "dsi"; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi0_in: endpoint { + remote-endpoint = <&dpu_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + dsi0_out: endpoint { + }; + }; + }; + }; + + dsi0_phy: dsi-phy@ae94400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae94400 0 0x200>, + <0 0x0ae94600 0 0x280>, + <0 0x0ae94900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + }; + + dsi1: dsi@ae96000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0 0x0ae96000 0 0x400>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <5 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>, + <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>, + <&dispcc DISP_CC_MDSS_PCLK1_CLK>, + <&dispcc DISP_CC_MDSS_ESC1_CLK>, + <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&gcc GCC_DISP_HF_AXI_CLK>; + clock-names = "byte", + "byte_intf", + "pixel", + "core", + "iface", + "bus"; + + operating-points-v2 = <&dsi_opp_table>; + power-domains = <&rpmhpd SM8250_MMCX>; + + phys = <&dsi1_phy>; + phy-names = "dsi"; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dsi1_in: endpoint { + remote-endpoint = <&dpu_intf2_out>; + }; + }; + + port@1 { + reg = <1>; + dsi1_out: endpoint { + }; + }; + }; + }; + + dsi1_phy: dsi-phy@ae96400 { + compatible = "qcom,dsi-phy-7nm"; + reg = <0 0x0ae96400 0 0x200>, + <0 0x0ae96600 0 0x280>, + <0 0x0ae96900 0 0x260>; + reg-names = "dsi_phy", + "dsi_phy_lane", + "dsi_pll"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>; + clock-names = "iface", "ref"; + + status = "disabled"; + + dsi_opp_table: dsi-opp-table { + compatible = "operating-points-v2"; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-300000000 { + opp-hz = /bits/ 64 <300000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-358000000 { + opp-hz = /bits/ 64 <358000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + }; + }; + }; + + dispcc: clock-controller@af00000 { + compatible = "qcom,sm8250-dispcc"; + reg = <0 0x0af00000 0 0x20000>; + clocks = <&rpmhcc RPMH_CXO_CLK>, + <&dsi0_phy 0>, + <&dsi0_phy 1>, + <&dsi1_phy 0>, + <&dsi1_phy 1>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <0>, + <&sleep_clk>; + clock-names = "bi_tcxo", + "dsi0_phy_pll_out_byteclk", + "dsi0_phy_pll_out_dsiclk", + "dsi1_phy_pll_out_byteclk", + "dsi1_phy_pll_out_dsiclk", + "dp_link_clk_divsel_ten", + "dp_vco_divided_clk_src_mux", + "dptx1_phy_pll_link_clk", + "dptx1_phy_pll_vco_div_clk", + "dptx2_phy_pll_link_clk", + "dptx2_phy_pll_vco_div_clk", + "edp_phy_pll_link_clk", + "edp_phy_pll_vco_div_clk", + "sleep_clk"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + pdc: interrupt-controller@b220000 { compatible = "qcom,sm8250-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; From 46967bb61a20f6eb7417193e494a62ba5b0f760f Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:21:00 +0300 Subject: [PATCH 027/584] arm64: dts: qrb5165-rb5: add mdss/mdp/dsi nodes Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-3-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 32 ++++++++++++++++++++++++ 1 file changed, 32 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index ce22d4fa383e..ce9d98e2d856 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -406,6 +406,30 @@ }; }; +&dsi0 { + status = "okay"; + vdda-supply = <&vreg_l9a_1p2>; + +#if 0 + qcom,dual-dsi-mode; + qcom,master-dsi; +#endif + + ports { + port@1 { + endpoint { + //remote-endpoint = <<9611_a>; + data-lanes = <0 1 2 3>; + }; + }; + }; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vreg_l5a_0p88>; +}; + /* LS-I2C0 */ &i2c4 { status = "okay"; @@ -420,6 +444,14 @@ status = "okay"; }; +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + &pm8150_gpios { gpio-reserved-ranges = <1 1>, <3 2>, <7 1>; gpio-line-names = From 0b2033dcf4afa399addacdf2f24600894fb947d7 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:21:01 +0300 Subject: [PATCH 028/584] arm64: dts: qcom: qrb5165-rb5: add gpu/zap-shader node Add firmware configuration for Adreno zap shader on qrb5165-rb5. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-4-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index ce9d98e2d856..22c1953f4e63 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -430,6 +430,13 @@ vdds-supply = <&vreg_l5a_0p88>; }; +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sm8250/a650_zap.mbn"; + }; +}; + /* LS-I2C0 */ &i2c4 { status = "okay"; From 9e301a547a7eadab8e6d4089eac9e6a123d18d23 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:21:02 +0300 Subject: [PATCH 029/584] arm64: dts: qcom: sm8250-mtp: add gpu/zap-shader node Add firmware configuration for Adreno zap shader on sm8250-mtp. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-5-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts index 3aac17604ff0..767a2e446248 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts @@ -365,6 +365,13 @@ firmware-name = "qcom/sm8250/cdsp.mbn"; }; +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sm8250/a650_zap.mbn"; + }; +}; + &i2c1 { status = "okay"; clock-frequency = <1000000>; From 04c8e3f7e9e9675a01182dea2a4ebe2fe26ad706 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:21:03 +0300 Subject: [PATCH 030/584] arm64: dts: qcom: qrb5165-rb5: correct vdc_3v3 regulator vdc_3v3 regulator is sourced from 12V, but it is controlled by l11c regulator, so set it as vin for vdc_3v3. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-6-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 22c1953f4e63..94d95dff48c4 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -87,7 +87,7 @@ vdc_3v3: vdc-3v3-regulator { compatible = "regulator-fixed"; regulator-name = "VDC_3V3"; - vin-supply = <&dc12v>; + vin-supply = <&vreg_l11c_3p3>; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; From d004c631ea4e1327cf04316ff444e7e078e00d77 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:21:04 +0300 Subject: [PATCH 031/584] arm64: dts: qcom: qrb5165-rb5: add lt9611 HDMI bridge Add device tree node for the lontium lt9611ux DSI-HDMI bridge. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-7-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 97 +++++++++++++++++++++++- 1 file changed, 96 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 94d95dff48c4..1ade62d98f98 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -40,6 +40,17 @@ regulator-always-on; }; + hdmi-out { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_con: endpoint { + remote-endpoint = <<9611_out>; + }; + }; + }; + leds { compatible = "gpio-leds"; @@ -66,6 +77,26 @@ }; + lt9611_1v2: lt9611-vdd12-regulator { + compatible = "regulator-fixed"; + regulator-name = "LT9611_1V2"; + + vin-supply = <&vdc_3v3>; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + lt9611_3v3: lt9611-3v3 { + compatible = "regulator-fixed"; + regulator-name = "LT9611_3V3"; + + vin-supply = <&vdc_3v3>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + vbat: vbat-regulator { compatible = "regulator-fixed"; regulator-name = "VBAT"; @@ -418,7 +449,7 @@ ports { port@1 { endpoint { - //remote-endpoint = <<9611_a>; + remote-endpoint = <<9611_a>; data-lanes = <0 1 2 3>; }; }; @@ -444,6 +475,55 @@ &i2c5 { status = "okay"; + clock-frequency = <400000>; + + lt9611_codec: hdmi-bridge@2b { + compatible = "lontium,lt9611uxc"; + reg = <0x2b>; + #sound-dai-cells = <1>; + + interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>; + + reset-gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_HIGH>; + + vdd-supply = <<9611_1v2>; + vcc-supply = <<9611_3v3>; + + pinctrl-names = "default"; + pinctrl-0 = <<9611_irq_pin <9611_rst_pin>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + lt9611_a: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + +#if 0 + port@1 { + reg = <1>; + + lt9611_b: endpoint { + remote-endpoint = <&dsi1_out>; + }; + }; +#endif + + port@2 { + reg = <2>; + + lt9611_out: endpoint { + remote-endpoint = <&hdmi_con>; + }; + }; + + }; + }; }; /* LS-I2C1 */ @@ -504,6 +584,15 @@ "PM_GPIO-B", "NC", "PM3003A_MODE"; + + lt9611_rst_pin: lt9611-rst-pin { + pins = "gpio5"; + function = "normal"; + + output-high; + input-disable; + power-source = <0>; + }; }; &pm8150_rtc { @@ -735,6 +824,12 @@ "HST_WLAN_UART_TX", "HST_WLAN_UART_RX"; + lt9611_irq_pin: lt9611-irq { + pins = "gpio63"; + function = "gpio"; + bias-disable; + }; + sdc2_default_state: sdc2-default { clk { pins = "sdc2_clk"; From 3f2094dfbe691d3d31b8a478c83495989773e390 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 17:21:05 +0300 Subject: [PATCH 032/584] arm64: dts: qcom: sm8250: power up dispcc on sm8250 by MMCX regulator Add regulator controlling MMCX power domain to be used by display clock controller on SM8250. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203142105.841666-8-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 827197f83f4f..ce571796561c 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -216,6 +216,13 @@ reg = <0x0 0x80000000 0x0 0x0>; }; + mmcx_reg: mmcx-reg { + compatible = "regulator-fixed-domain"; + power-domains = <&rpmhpd SM8250_MMCX>; + required-opps = <&rpmhpd_opp_low_svs>; + regulator-name = "MMCX"; + }; + pmu { compatible = "arm,armv8-pmuv3"; interrupts = ; @@ -2064,6 +2071,7 @@ dispcc: clock-controller@af00000 { compatible = "qcom,sm8250-dispcc"; reg = <0 0x0af00000 0 0x20000>; + mmcx-supply = <&mmcx_reg>; clocks = <&rpmhcc RPMH_CXO_CLK>, <&dsi0_phy 0>, <&dsi0_phy 1>, From 63e10791ccab664abc031b7fad07674fdae2d829 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Wed, 2 Dec 2020 18:07:36 +0000 Subject: [PATCH 033/584] arm64: dts: qcom: sm8250: add apr and its services Add apr node and its associated services required for audio on RB5. Signed-off-by: Srinivas Kandagatla Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201202180741.16386-2-srinivas.kandagatla@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 56 ++++++++++++++++++++++++++++ 1 file changed, 56 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index ce571796561c..3aca8d0af97c 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -13,7 +13,9 @@ #include #include #include +#include #include +#include #include / { @@ -2922,6 +2924,60 @@ label = "lpass"; qcom,remote-pid = <2>; + apr { + compatible = "qcom,apr-v2"; + qcom,glink-channels = "apr_audio_svc"; + qcom,apr-domain = ; + #address-cells = <1>; + #size-cells = <0>; + + apr-service@3 { + reg = ; + compatible = "qcom,q6core"; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + }; + + q6afe: apr-service@4 { + compatible = "qcom,q6afe"; + reg = ; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + q6afedai: dais { + compatible = "qcom,q6afe-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + }; + + q6afecc: cc { + compatible = "qcom,q6afe-clocks"; + #clock-cells = <2>; + }; + }; + + q6asm: apr-service@7 { + compatible = "qcom,q6asm"; + reg = ; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + q6asmdai: dais { + compatible = "qcom,q6asm-dais"; + #address-cells = <1>; + #size-cells = <0>; + #sound-dai-cells = <1>; + iommus = <&apps_smmu 0x1801 0x0>; + }; + }; + + q6adm: apr-service@8 { + compatible = "qcom,q6adm"; + reg = ; + qcom,protection-domain = "avs/audio", "msm/adsp/audio_pd"; + q6routing: routing { + compatible = "qcom,q6adm-routing"; + #sound-dai-cells = <0>; + }; + }; + }; + fastrpc { compatible = "qcom,fastrpc"; qcom,glink-channels = "fastrpcglink-apps-dsp"; From 793bbd2db7e35a9dbf006e81a8373cd1c333ae53 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Wed, 2 Dec 2020 18:07:37 +0000 Subject: [PATCH 034/584] arm64: dts: qcom: sm8250: add audio clock controllers Add audiocc and aoncc clock controller nodes required for audio on RB5. Signed-off-by: Srinivas Kandagatla Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201202180741.16386-3-srinivas.kandagatla@linaro.org [bjorn: Dropped includes for now] Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 3aca8d0af97c..98d58943cd05 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1264,6 +1264,26 @@ #hwlock-cells = <1>; }; + audiocc: clock-controller@3300000 { + compatible = "qcom,sm8250-lpass-audiocc"; + reg = <0 0x03300000 0 0x30000>; + #clock-cells = <1>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio", "bus"; + }; + + aoncc: clock-controller@3380000 { + compatible = "qcom,sm8250-lpass-aoncc"; + reg = <0 0x03380000 0 0x40000>; + #clock-cells = <1>; + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio", "bus"; + }; + gpu: gpu@3d00000 { compatible = "qcom,adreno-650.2", "qcom,adreno"; From 3160c1b894d9cf5373457f260d4660d6269204ae Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Wed, 2 Dec 2020 18:07:38 +0000 Subject: [PATCH 035/584] arm64: dts: qcom: sm8250: add lpass lpi pin controller node Add LPASS LPI pinctrl node required for Audio functionality on RB5. Signed-off-by: Srinivas Kandagatla Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201202180741.16386-4-srinivas.kandagatla@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 84 ++++++++++++++++++++++++++++ 1 file changed, 84 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 98d58943cd05..7badccba186b 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1284,6 +1284,90 @@ clock-names = "core", "audio", "bus"; }; + lpass_tlmm: pinctrl@33c0000{ + compatible = "qcom,sm8250-lpass-lpi-pinctrl"; + reg = <0 0x033c0000 0x0 0x20000>, + <0 0x03550000 0x0 0x10000>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&lpass_tlmm 0 0 14>; + + clocks = <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + clock-names = "core", "audio"; + + wsa_swr_active: wsa-swr-active-pins { + clk { + pins = "gpio10"; + function = "wsa_swr_clk"; + drive-strength = <2>; + slew-rate = <1>; + bias-disable; + }; + + data { + pins = "gpio11"; + function = "wsa_swr_data"; + drive-strength = <2>; + slew-rate = <1>; + bias-bus-hold; + + }; + }; + + wsa_swr_sleep: wsa-swr-sleep-pins { + clk { + pins = "gpio10"; + function = "wsa_swr_clk"; + drive-strength = <2>; + input-enable; + bias-pull-down; + }; + + data { + pins = "gpio11"; + function = "wsa_swr_data"; + drive-strength = <2>; + input-enable; + bias-pull-down; + + }; + }; + + dmic01_active: dmic01-active-pins { + clk { + pins = "gpio6"; + function = "dmic1_clk"; + drive-strength = <8>; + output-high; + }; + data { + pins = "gpio7"; + function = "dmic1_data"; + drive-strength = <8>; + input-enable; + }; + }; + + dmic01_sleep: dmic01-sleep-pins { + clk { + pins = "gpio6"; + function = "dmic1_clk"; + drive-strength = <2>; + bias-disable; + output-low; + }; + + data { + pins = "gpio7"; + function = "dmic1_data"; + drive-strength = <2>; + pull-down; + input-enable; + }; + }; + }; + gpu: gpu@3d00000 { compatible = "qcom,adreno-650.2", "qcom,adreno"; From 768270ca57f6a495c9c1d81a1b01ab5ad604b321 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Wed, 2 Dec 2020 18:07:39 +0000 Subject: [PATCH 036/584] arm64: dts: qcom: sm8250: add wsa and va codec macros Add support for WSA and VA codec macros along with WSA soundwire controller required for getting audio on RB5. Signed-off-by: Srinivas Kandagatla Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201202180741.16386-5-srinivas.kandagatla@linaro.org [bjorn: Replaced LPASS_CDC clock defines with constants] Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 56 ++++++++++++++++++++++++++++ 1 file changed, 56 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 7badccba186b..ad0a0a887cc8 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1264,6 +1264,47 @@ #hwlock-cells = <1>; }; + wsamacro: codec@3240000 { + compatible = "qcom,sm8250-lpass-wsa-macro"; + reg = <0 0x03240000 0 0x1000>; + clocks = <&audiocc 1>, + <&audiocc 0>, + <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&aoncc 0>, + <&vamacro>; + + clock-names = "mclk", "npl", "macro", "dcodec", "va", "fsgen"; + + #clock-cells = <0>; + clock-frequency = <9600000>; + clock-output-names = "mclk"; + #sound-dai-cells = <1>; + + pinctrl-names = "default"; + pinctrl-0 = <&wsa_swr_active>; + }; + + swr0: soundwire-controller@3250000 { + reg = <0 0x03250000 0 0x2000>; + compatible = "qcom,soundwire-v1.5.1"; + interrupts = ; + clocks = <&wsamacro>; + clock-names = "iface"; + + qcom,din-ports = <2>; + qcom,dout-ports = <6>; + + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1f 0x3f 0x07 0x1f 0x3f 0x0f 0x0f>; + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0c 0x06 0x12 0x0d 0x07 0x0a>; + qcom,ports-offset2 = /bits/ 8 <0xff 0x00 0x1f 0xff 0x00 0x1f 0x00 0x00>; + qcom,ports-block-pack-mode = /bits/ 8 <0x0 0x0 0x1 0x0 0x0 0x1 0x0 0x0>; + + #sound-dai-cells = <1>; + #address-cells = <2>; + #size-cells = <0>; + }; + audiocc: clock-controller@3300000 { compatible = "qcom,sm8250-lpass-audiocc"; reg = <0 0x03300000 0 0x30000>; @@ -1274,6 +1315,21 @@ clock-names = "core", "audio", "bus"; }; + vamacro: codec@3370000 { + compatible = "qcom,sm8250-lpass-va-macro"; + reg = <0 0x03370000 0 0x1000>; + clocks = <&aoncc 0>, + <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>, + <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>; + + clock-names = "mclk", "macro", "dcodec"; + + #clock-cells = <0>; + clock-frequency = <9600000>; + clock-output-names = "fsgen"; + #sound-dai-cells = <1>; + }; + aoncc: clock-controller@3380000 { compatible = "qcom,sm8250-lpass-aoncc"; reg = <0 0x03380000 0 0x40000>; From b657d372627091b832f6aa87d8eae92154c77659 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Wed, 2 Dec 2020 18:07:40 +0000 Subject: [PATCH 037/584] arm64: dts: qcom: sm8250: add mi2s pinconfs Add primary and tertinary mi2s pinconfs required to get I2S audio. Signed-off-by: Srinivas Kandagatla Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201202180741.16386-6-srinivas.kandagatla@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 55 ++++++++++++++++++++++++++++ 1 file changed, 55 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index ad0a0a887cc8..ed5386214355 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -2344,6 +2344,37 @@ gpio-ranges = <&tlmm 0 0 180>; wakeup-parent = <&pdc>; + pri_mi2s_active: pri-mi2s-active { + sclk { + pins = "gpio138"; + function = "mi2s0_sck"; + drive-strength = <8>; + bias-disable; + }; + + ws { + pins = "gpio141"; + function = "mi2s0_ws"; + drive-strength = <8>; + output-high; + }; + + data0 { + pins = "gpio139"; + function = "mi2s0_data0"; + drive-strength = <8>; + bias-disable; + output-high; + }; + + data1 { + pins = "gpio140"; + function = "mi2s0_data1"; + drive-strength = <8>; + output-high; + }; + }; + qup_i2c0_default: qup-i2c0-default { mux { pins = "gpio28", "gpio29"; @@ -2940,6 +2971,30 @@ function = "qup18"; }; }; + + tert_mi2s_active: tert-mi2s-active { + sck { + pins = "gpio133"; + function = "mi2s2_sck"; + drive-strength = <8>; + bias-disable; + }; + + data0 { + pins = "gpio134"; + function = "mi2s2_data0"; + drive-strength = <8>; + bias-disable; + output-high; + }; + + ws { + pins = "gpio135"; + function = "mi2s2_ws"; + drive-strength = <8>; + output-high; + }; + }; }; apps_smmu: iommu@15000000 { From 590a135ebdc7053ec81e35be2a517b916c002ef9 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Wed, 2 Dec 2020 18:07:41 +0000 Subject: [PATCH 038/584] arm64: dts: qcom: qrb5165-rb5: Add Audio support This patch add support for two WSA881X smart speakers attached via Soundwire and a DMIC0 on the main board. Signed-off-by: Srinivas Kandagatla Tested-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201202180741.16386-7-srinivas.kandagatla@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 121 +++++++++++++++++++++++ arch/arm64/boot/dts/qcom/sm8250.dtsi | 3 + 2 files changed, 124 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 1ade62d98f98..477ff91dc460 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -7,6 +7,8 @@ #include #include +#include +#include #include "sm8250.dtsi" #include "pm8150.dtsi" #include "pm8150b.dtsi" @@ -151,6 +153,11 @@ }; }; +&adsp { + status = "okay"; + firmware-name = "qcom/sm8250/adsp.mbn"; +}; + &apps_rsc { pm8009-rpmh-regulators { compatible = "qcom,pm8009-rpmh-regulators"; @@ -611,6 +618,35 @@ status = "okay"; }; +&q6afedai { + qi2s@16 { + reg = <16>; + qcom,sd-lines = <0 1 2 3>; + }; +}; + +/* TERT I2S Uses 1 I2S SD Lines for audio on LT9611 HDMI Bridge */ +&q6afedai { + qi2s@20 { + reg = <20>; + qcom,sd-lines = <0>; + }; +}; + +&q6asmdai { + dai@0 { + reg = <0>; + }; + + dai@1 { + reg = <1>; + }; + + dai@2 { + reg = <2>; + }; +}; + &sdhc_2 { status = "okay"; pinctrl-names = "default"; @@ -625,6 +661,84 @@ no-emmc; }; +&swr0 { + left_spkr: wsa8810-left{ + compatible = "sdw10217211000"; + reg = <0 3>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrLeft"; + #sound-dai-cells = <0>; + }; + + right_spkr: wsa8810-right{ + compatible = "sdw10217211000"; + reg = <0 4>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrRight"; + #sound-dai-cells = <0>; + }; +}; + +&sound { + compatible = "qcom,qrb5165-rb5-sndcard"; + pinctrl-0 = <&tert_mi2s_active>; + pinctrl-names = "default"; + model = "Qualcomm-RB5-WSA8815-Speakers-DMIC0"; + audio-routing = + "SpkrLeft IN", "WSA_SPK1 OUT", + "SpkrRight IN", "WSA_SPK2 OUT", + "VA DMIC0", "vdd-micb", + "VA DMIC1", "vdd-micb", + "MM_DL1", "MultiMedia1 Playback", + "MultiMedia3 Capture", "MM_UL3"; + + mm1-dai-link { + link-name = "MultiMedia1"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; + }; + }; + + mm3-dai-link { + link-name = "MultiMedia3"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>; + }; + }; + + dma-dai-link { + link-name = "WSA Playback"; + cpu { + sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>; + }; + }; + + va-dai-link { + link-name = "VA Capture"; + cpu { + sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <&vamacro 0>; + }; + }; +}; + /* CAN */ &spi0 { status = "okay"; @@ -926,3 +1040,10 @@ vdda-phy-supply = <&vreg_l9a_1p2>; vdda-pll-supply = <&vreg_l18a_0p92>; }; + +&vamacro { + pinctrl-0 = <&dmic01_active>; + pinctrl-names = "default"; + vdd-micb-supply = <&vreg_s4a_1p8>; + qcom,dmic-sample-rate = <600000>; +}; diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index ed5386214355..9af0bb76f24a 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1722,6 +1722,9 @@ }; }; + sound: sound { + }; + usb_1_hsphy: phy@88e3000 { compatible = "qcom,sm8250-usb-hs-phy", "qcom,usb-snps-hs-7nm-phy"; From 88b57bc335aec493531a75505391d837041ab935 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 3 Dec 2020 22:13:35 +0300 Subject: [PATCH 039/584] arm64: dts: qcom: sm8250: rename smem device node to follow schema Rename 'qcom,smem' to just 'smem' to follow the rest of SoC (and device schema). Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20201203191335.927001-2-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 9af0bb76f24a..6b4cf4426859 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -332,7 +332,7 @@ }; }; - smem: qcom,smem { + smem { compatible = "qcom,smem"; memory-region = <&smem_mem>; hwlocks = <&tcsr_mutex 3>; From 465b13cc0ac1e792d844117636296c4359e15504 Mon Sep 17 00:00:00 2001 From: Douglas Anderson Date: Fri, 4 Dec 2020 10:49:02 -0800 Subject: [PATCH 040/584] arm64: dts: qcom: Fix SD card vqmmc max voltage on sc7180-trogdor It never makes sense to set the IO voltage of the SD card (vqmmc) to a voltage that's higher than the voltage of the card's main power supply (vmmc). The card's main voltage is 2.952V on trogdor, so let's set the max for the IO voltage to the same. NOTE: On Linux, this is pretty much a no-op currently. Linux already makes an effort to match vqmmc with vmmc when running at "3.3" signal voltage, so both before and after this change we end up running vqmmc at 2.904V when talking to non-UHS cards. It still seems cleaner to make it a little more correct, though. Also note: as per above, on Linux right now we end up running vqmmc as 2.904V even though vmmc is 2.952V. This isn't super ideal but shouldn't really hurt. Signed-off-by: Douglas Anderson Link: https://lore.kernel.org/r/20201204104900.1.I0a4ac2c7f4d405431cf95eb7b7c36800660516ec@changeid Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index 8ed7dd39f6e3..d76200d2b373 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -509,7 +509,7 @@ vddpx_2: ppvar_l6c: ldo6 { regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3304000>; + regulator-max-microvolt = <2952000>; regulator-initial-mode = ; }; From bd167507d5b6fffe176eae56d9d9c0b3d26b64e6 Mon Sep 17 00:00:00 2001 From: "J.R. Divya Antony" Date: Wed, 9 Dec 2020 20:07:44 +0530 Subject: [PATCH 041/584] arm64: dts: qcom: Add device tree for ASUS Zenfone 2 Laser ASUS Zenfone 2 Laser Z00L is a smartphone based on MSM8916 SoC released on 2015. Add a device tree for Z00L with initial support for: - SDHCI (internal storage) - USB Device Mode - UART - Regulators Reviewed-by: Stephan Gerhold Signed-off-by: J.R. Divya Antony Link: https://lore.kernel.org/r/20201209143743.7383-1-d.antony.jr@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../arm64/boot/dts/qcom/msm8916-asus-z00l.dts | 195 ++++++++++++++++++ 2 files changed, 196 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 5113fac80b7a..6a4be237f344 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts new file mode 100644 index 000000000000..cee451e59385 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts @@ -0,0 +1,195 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include + +/ { + model = "Asus Zenfone 2 Laser"; + compatible = "asus,z00l", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <15>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&msmgpio 117 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <15>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&msmgpio 110 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + gpio_keys_default: gpio-keys-default { + pins = "gpio107", "gpio117"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + usb_id_default: usb-id-default { + pins = "gpio110"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; From 8d079bf20410aeb2cc714d8781d3a0930f85448f Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Mon, 14 Dec 2020 18:00:04 -0800 Subject: [PATCH 042/584] arm64: dts: qcom: sc7180: Drop pinconf on dp_hot_plug_det We shouldn't put any pinconf here in case someone decides to invert this HPD signal or remove an external pull-down. It's better to leave that to the board pinconf nodes, so drop it here. Reviewed-by: Douglas Anderson Reported-by: Douglas Anderson Cc: Tanmay Shah Fixes: 681a607ad21a ("arm64: dts: qcom: sc7180: Add DisplayPort HPD pin dt node") Signed-off-by: Stephen Boyd Link: https://lore.kernel.org/r/20201215020004.731239-1-swboyd@chromium.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180.dtsi | 6 ------ 1 file changed, 6 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 22b832fc62e3..268fa40a1774 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -1468,12 +1468,6 @@ pins = "gpio117"; function = "dp_hot"; }; - - pinconf { - pins = "gpio117"; - bias-disable; - input-enable; - }; }; qspi_clk: qspi-clk { From abe533d9d422b101f4a08a8741ac01a7dc1e83bf Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Tue, 8 Dec 2020 08:03:03 +0100 Subject: [PATCH 043/584] dt-bindings: arm: bcm: document Netgear R8000P binding MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It's a BCM4906 based device. Signed-off-by: RafaÅ‚ MiÅ‚ecki Acked-by: Rob Herring Signed-off-by: Florian Fainelli --- Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml index 5fec063d9a13..e55731f43c84 100644 --- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml +++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml @@ -19,6 +19,8 @@ properties: oneOf: - description: BCM4906 based boards items: + - enum: + - netgear,r8000p - const: brcm,bcm4906 - const: brcm,bcm4908 From c8b404fb05dcfadff477e49b7ea6b500e015f101 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Tue, 8 Dec 2020 08:03:04 +0100 Subject: [PATCH 044/584] arm64: dts: broadcom: bcm4908: add BCM4906 Netgear R8000P DTS files MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Netgear R8000P is home router based on BCM4906 that is a cheaper variant of BCM4908 (e.g. 2 cores instead of 4). Signed-off-by: RafaÅ‚ MiÅ‚ecki Signed-off-by: Florian Fainelli --- arch/arm64/boot/dts/broadcom/bcm4908/Makefile | 1 + .../bcm4908/bcm4906-netgear-r8000p.dts | 52 +++++++++++++++++++ .../boot/dts/broadcom/bcm4908/bcm4906.dtsi | 18 +++++++ 3 files changed, 71 insertions(+) create mode 100644 arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts create mode 100644 arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile index ef26c23603ce..ebebc0cd421f 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile +++ b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile @@ -1,2 +1,3 @@ # SPDX-License-Identifier: GPL-2.0 +dtb-$(CONFIG_ARCH_BCM4908) += bcm4906-netgear-r8000p.dtb dtb-$(CONFIG_ARCH_BCM4908) += bcm4908-asus-gt-ac5300.dtb diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts new file mode 100644 index 000000000000..ee3ed612274c --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts @@ -0,0 +1,52 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include +#include +#include + +#include "bcm4906.dtsi" + +/ { + compatible = "netgear,r8000p", "brcm,bcm4906", "brcm,bcm4908"; + model = "Netgear R8000P"; + + memory@0 { + device_type = "memory"; + reg = <0x00 0x00 0x00 0x20000000>; + }; + + leds { + compatible = "gpio-leds"; + + wps { + function = LED_FUNCTION_WPS; + color = ; + gpios = <&gpio0 10 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&nandcs { + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-on-flash-bbt; + + #address-cells = <1>; + #size-cells = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "cferom"; + reg = <0x0 0x100000>; + }; + + partition@100000 { + label = "firmware"; + reg = <0x100000 0x4400000>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi new file mode 100644 index 000000000000..66023d553524 --- /dev/null +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi @@ -0,0 +1,18 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "bcm4908.dtsi" + +/ { + cpus { + /delete-node/ cpu@2; + + /delete-node/ cpu@3; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = , + ; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; +}; From 56098be85d19cd56b59d7b3854ea035cc8cb9e95 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Tue, 8 Dec 2020 11:49:50 +0100 Subject: [PATCH 045/584] arm64: dts: broadcom: bcm4908: use proper NAND binding MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit BCM4908 has controller that needs different IRQ handling just like the BCM63138. Describe it properly. On Linux this change fixes: brcmstb_nand ff801800.nand: timeout waiting for command 0x9 brcmstb_nand ff801800.nand: intfc status d0000000 Signed-off-by: RafaÅ‚ MiÅ‚ecki Signed-off-by: Florian Fainelli --- arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi index f873dc44ce9c..55d9b56ac749 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi @@ -164,7 +164,7 @@ nand@1800 { #address-cells = <1>; #size-cells = <0>; - compatible = "brcm,brcmnand-v7.1", "brcm,brcmnand"; + compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand"; reg = <0x1800 0x600>, <0x2000 0x10>; reg-names = "nand", "nand-int-base"; interrupts = ; From 1b88c6ed26a1aa1d68d1661404e6e939709ff530 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Thu, 10 Dec 2020 08:21:54 +0100 Subject: [PATCH 046/584] arm64: dts: broadcom: bcm4908: describe PCIe reset controller MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This reset controller is a single register in the Broadcom's MISC block. Signed-off-by: RafaÅ‚ MiÅ‚ecki Signed-off-by: Florian Fainelli --- arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi index 55d9b56ac749..b5b772a9a51b 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi @@ -177,6 +177,21 @@ }; }; + misc@2600 { + compatible = "brcm,misc", "simple-mfd"; + reg = <0x2600 0xe4>; + + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x2600 0xe4>; + + reset-controller@2644 { + compatible = "brcm,bcm4908-misc-pcie-reset"; + reg = <0x44 0x04>; + #reset-cells = <1>; + }; + }; + reboot { compatible = "syscon-reboot"; regmap = <&timer>; From 75681980c4e3d89c55b5b8f20b8f4c1aace601be Mon Sep 17 00:00:00 2001 From: Marek Szyprowski Date: Fri, 20 Nov 2020 09:56:37 +0100 Subject: [PATCH 047/584] ARM: dts: exynos: use Exynos5420 dedicated USB2 PHY compatible USB2.0 PHY in Exynos5420 differs from Exynos5250 variant a bit, so use the recently introduced dedicated compatible for Exynos5420. Signed-off-by: Marek Szyprowski Link: https://lore.kernel.org/r/20201120085637.7299-3-m.szyprowski@samsung.com Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos54xx.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/exynos54xx.dtsi b/arch/arm/boot/dts/exynos54xx.dtsi index fe9d34c23374..2ddb7a5f12b3 100644 --- a/arch/arm/boot/dts/exynos54xx.dtsi +++ b/arch/arm/boot/dts/exynos54xx.dtsi @@ -188,7 +188,7 @@ compatible = "samsung,exynos4210-ehci"; reg = <0x12110000 0x100>; interrupts = ; - phys = <&usb2_phy 1>; + phys = <&usb2_phy 0>; phy-names = "host"; }; @@ -196,12 +196,12 @@ compatible = "samsung,exynos4210-ohci"; reg = <0x12120000 0x100>; interrupts = ; - phys = <&usb2_phy 1>; + phys = <&usb2_phy 0>; phy-names = "host"; }; usb2_phy: phy@12130000 { - compatible = "samsung,exynos5250-usb2-phy"; + compatible = "samsung,exynos5420-usb2-phy"; reg = <0x12130000 0x100>; #phy-cells = <1>; }; From cb31334687db31c691901269d65074a7ffaecb18 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:28:55 +0100 Subject: [PATCH 048/584] ARM: dts: exynos: correct PMIC interrupt trigger level on Artik 5 The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. Without specifying the interrupt type in Devicetree, kernel might apply some fixed configuration, not necessarily working for this hardware. Fixes: b004a34bd0ff ("ARM: dts: exynos: Add exynos3250-artik5 dtsi file for ARTIK5 module") Signed-off-by: Krzysztof Kozlowski Tested-by: Marek Szyprowski Link: https://lore.kernel.org/r/20201210212903.216728-1-krzk@kernel.org --- arch/arm/boot/dts/exynos3250-artik5.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos3250-artik5.dtsi b/arch/arm/boot/dts/exynos3250-artik5.dtsi index 04290ec4583a..829c05b2c405 100644 --- a/arch/arm/boot/dts/exynos3250-artik5.dtsi +++ b/arch/arm/boot/dts/exynos3250-artik5.dtsi @@ -79,7 +79,7 @@ pmic@66 { compatible = "samsung,s2mps14-pmic"; interrupt-parent = <&gpx3>; - interrupts = <5 IRQ_TYPE_NONE>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&s2mps14_irq>; reg = <0x66>; From 8528cda2b7c667e9cd173aef1a677c71b7d5a096 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:28:56 +0100 Subject: [PATCH 049/584] ARM: dts: exynos: correct PMIC interrupt trigger level on Monk The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. Without specifying the interrupt type in Devicetree, kernel might apply some fixed configuration, not necessarily working for this hardware. Fixes: e0cefb3f79d3 ("ARM: dts: add board dts file for Exynos3250-based Monk board") Signed-off-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20201210212903.216728-2-krzk@kernel.org --- arch/arm/boot/dts/exynos3250-monk.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts index 69451566945d..fae046e08a5d 100644 --- a/arch/arm/boot/dts/exynos3250-monk.dts +++ b/arch/arm/boot/dts/exynos3250-monk.dts @@ -200,7 +200,7 @@ pmic@66 { compatible = "samsung,s2mps14-pmic"; interrupt-parent = <&gpx0>; - interrupts = <7 IRQ_TYPE_NONE>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; reg = <0x66>; wakeup-source; From 437ae60947716bb479e2f32466f49445c0509b1e Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:28:57 +0100 Subject: [PATCH 050/584] ARM: dts: exynos: correct PMIC interrupt trigger level on Rinato The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. Without specifying the interrupt type in Devicetree, kernel might apply some fixed configuration, not necessarily working for this hardware. Fixes: faaf348ef468 ("ARM: dts: Add board dts file for exynos3250-rinato") Signed-off-by: Krzysztof Kozlowski Tested-by: Marek Szyprowski Link: https://lore.kernel.org/r/20201210212903.216728-3-krzk@kernel.org --- arch/arm/boot/dts/exynos3250-rinato.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts index a26e3e582a7e..d64ccf4b7d32 100644 --- a/arch/arm/boot/dts/exynos3250-rinato.dts +++ b/arch/arm/boot/dts/exynos3250-rinato.dts @@ -270,7 +270,7 @@ pmic@66 { compatible = "samsung,s2mps14-pmic"; interrupt-parent = <&gpx0>; - interrupts = <7 IRQ_TYPE_NONE>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; reg = <0x66>; wakeup-source; From 77e6a5467cb8657cf8b5e610a30a4c502085e4f9 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:28:58 +0100 Subject: [PATCH 051/584] ARM: dts: exynos: correct PMIC interrupt trigger level on Spring The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. Without specifying the interrupt type in Devicetree, kernel might apply some fixed configuration, not necessarily working for this hardware. Fixes: 53dd4138bb0a ("ARM: dts: Add exynos5250-spring device tree") Signed-off-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20201210212903.216728-4-krzk@kernel.org --- arch/arm/boot/dts/exynos5250-spring.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts index 9d2baea62d0d..fba1462b19df 100644 --- a/arch/arm/boot/dts/exynos5250-spring.dts +++ b/arch/arm/boot/dts/exynos5250-spring.dts @@ -109,7 +109,7 @@ compatible = "samsung,s5m8767-pmic"; reg = <0x66>; interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_NONE>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; wakeup-source; From 1ac8893c4fa3d4a34915dc5cdab568a39db5086c Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:28:59 +0100 Subject: [PATCH 052/584] ARM: dts: exynos: correct PMIC interrupt trigger level on Arndale Octa The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. The falling edge interrupt will mostly work but it's not correct. Fixes: 1fed2252713e ("ARM: dts: fix pinctrl for s2mps11-irq on exynos5420-arndale-octa") Signed-off-by: Krzysztof Kozlowski Tested-by: Marek Szyprowski Link: https://lore.kernel.org/r/20201210212903.216728-5-krzk@kernel.org --- arch/arm/boot/dts/exynos5420-arndale-octa.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts index bf457d0c02eb..1aad4859c5f1 100644 --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts @@ -349,7 +349,7 @@ reg = <0x66>; interrupt-parent = <&gpx3>; - interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&s2mps11_irq>; From 3e7d9a583a24f7582c6bc29a0d4d624feedbc2f9 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:29:00 +0100 Subject: [PATCH 053/584] ARM: dts: exynos: correct PMIC interrupt trigger level on Odroid XU3 family The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. The falling edge interrupt will mostly work but it's not correct. Fixes: aac4e0615341 ("ARM: dts: odroidxu3: Enable wake alarm of S2MPS11 RTC") Signed-off-by: Krzysztof Kozlowski Tested-by: Marek Szyprowski Link: https://lore.kernel.org/r/20201210212903.216728-6-krzk@kernel.org --- arch/arm/boot/dts/exynos5422-odroid-core.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi index d0df560eb0db..6d690b1db099 100644 --- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi +++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi @@ -509,7 +509,7 @@ samsung,s2mps11-acokb-ground; interrupt-parent = <&gpx0>; - interrupts = <4 IRQ_TYPE_EDGE_FALLING>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; pinctrl-names = "default"; pinctrl-0 = <&s2mps11_irq>; From e98e2367dfb4b6d7a80c8ce795c644124eff5f36 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:29:01 +0100 Subject: [PATCH 054/584] arm64: dts: exynos: correct PMIC interrupt trigger level on TM2 The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. Without specifying the interrupt type in Devicetree, kernel might apply some fixed configuration, not necessarily working for this hardware. Fixes: 01e5d2352152 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board") Signed-off-by: Krzysztof Kozlowski Tested-by: Marek Szyprowski Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org --- arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi index 03486a8ffc67..4c5106a0860d 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi @@ -388,7 +388,7 @@ pmic@66 { compatible = "samsung,s2mps13-pmic"; interrupt-parent = <&gpa0>; - interrupts = <7 IRQ_TYPE_NONE>; + interrupts = <7 IRQ_TYPE_LEVEL_LOW>; reg = <0x66>; samsung,s2mps11-wrstbi-ground; From 1fea2eb2f5bbd3fbbe2513d2386b5f6e6db17fd7 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:29:02 +0100 Subject: [PATCH 055/584] arm64: dts: exynos: correct PMIC interrupt trigger level on Espresso The Samsung PMIC datasheets describe the interrupt line as active low with a requirement of acknowledge from the CPU. Without specifying the interrupt type in Devicetree, kernel might apply some fixed configuration, not necessarily working for this hardware. Fixes: 9589f7721e16 ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso") Signed-off-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20201210212903.216728-8-krzk@kernel.org --- arch/arm64/boot/dts/exynos/exynos7-espresso.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts index 695d4c140646..125c03f351d9 100644 --- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts +++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts @@ -90,7 +90,7 @@ pmic@66 { compatible = "samsung,s2mps15-pmic"; reg = <0x66>; - interrupts = <2 IRQ_TYPE_NONE>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; interrupt-parent = <&gpa0>; pinctrl-names = "default"; pinctrl-0 = <&pmic_irq>; From 545a540a9c2ec192cdd5c75af1e334711a79354a Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Thu, 10 Dec 2020 22:18:58 +0100 Subject: [PATCH 056/584] arm64: dts: exynos: correct S3FWRN5 NFC interrupt trigger level on TM2 The S3FWRN5 datasheet describe the interrupt line as rising edge. The current configuration as level high, could cause spurious interrupts. Signed-off-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20201210211859.215047-1-krzk@kernel.org --- arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi index 4c5106a0860d..413cac63a1cb 100644 --- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi @@ -793,7 +793,7 @@ compatible = "samsung,s3fwrn5-i2c"; reg = <0x27>; interrupt-parent = <&gpa1>; - interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <3 IRQ_TYPE_EDGE_RISING>; en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>; wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>; }; From b4d1e231fcdc343fb48d76c48b7518f89f3b7350 Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:16 +0200 Subject: [PATCH 057/584] arm: dts: owl-s500: Add Clock Management Unit Add Clock Management Unit for Actions Semi S500 SoC. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index 1dbe4e8b38ac..5d5ad9db549b 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -5,6 +5,7 @@ * Copyright (c) 2016-2017 Andreas Färber */ +#include #include #include @@ -70,6 +71,12 @@ #clock-cells = <0>; }; + losc: losc { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; @@ -169,6 +176,13 @@ status = "disabled"; }; + cmu: clock-controller@b0160000 { + compatible = "actions,s500-cmu"; + reg = <0xb0160000 0x8000>; + clocks = <&hosc>, <&losc>; + #clock-cells = <1>; + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>; From 11bc96ba758bf05a8048522d477c5953176132c9 Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:17 +0200 Subject: [PATCH 058/584] arm: dts: owl-s500: Set CMU clocks for UARTs Set Clock Management Unit clocks for the UART nodes of Actions Semi S500 SoCs and remove the dummy "uart2_clk" and "uart3_clk" fixed clocks. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500-cubieboard6.dts | 7 ------- arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts | 7 ------- arch/arm/boot/dts/owl-s500-labrador-base-m.dts | 7 ------- arch/arm/boot/dts/owl-s500-roseapplepi.dts | 7 ------- arch/arm/boot/dts/owl-s500-sparky.dts | 7 ------- arch/arm/boot/dts/owl-s500.dtsi | 7 +++++++ 6 files changed, 7 insertions(+), 35 deletions(-) diff --git a/arch/arm/boot/dts/owl-s500-cubieboard6.dts b/arch/arm/boot/dts/owl-s500-cubieboard6.dts index 7c96c59b610d..c2b02895910c 100644 --- a/arch/arm/boot/dts/owl-s500-cubieboard6.dts +++ b/arch/arm/boot/dts/owl-s500-cubieboard6.dts @@ -25,12 +25,6 @@ device_type = "memory"; reg = <0x0 0x80000000>; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &timer { @@ -39,5 +33,4 @@ &uart3 { status = "okay"; - clocks = <&uart3_clk>; }; diff --git a/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts b/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts index e610d49395d2..7ae34a23e320 100644 --- a/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts +++ b/arch/arm/boot/dts/owl-s500-guitar-bb-rev-b.dts @@ -18,15 +18,8 @@ chosen { stdout-path = "serial3:115200n8"; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &uart3 { status = "okay"; - clocks = <&uart3_clk>; }; diff --git a/arch/arm/boot/dts/owl-s500-labrador-base-m.dts b/arch/arm/boot/dts/owl-s500-labrador-base-m.dts index c92f8bdcb331..1585e33f703b 100644 --- a/arch/arm/boot/dts/owl-s500-labrador-base-m.dts +++ b/arch/arm/boot/dts/owl-s500-labrador-base-m.dts @@ -21,15 +21,8 @@ chosen { stdout-path = "serial3:115200n8"; }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &uart3 { status = "okay"; - clocks = <&uart3_clk>; }; diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts index a2087e617cb2..800edf5d2d12 100644 --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts @@ -25,12 +25,6 @@ device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; - - uart2_clk: uart2-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &twd_timer { @@ -43,5 +37,4 @@ &uart2 { status = "okay"; - clocks = <&uart2_clk>; }; diff --git a/arch/arm/boot/dts/owl-s500-sparky.dts b/arch/arm/boot/dts/owl-s500-sparky.dts index c665ce8b88b4..9d8f7336bec0 100644 --- a/arch/arm/boot/dts/owl-s500-sparky.dts +++ b/arch/arm/boot/dts/owl-s500-sparky.dts @@ -25,12 +25,6 @@ device_type = "memory"; reg = <0x0 0x40000000>; /* 1 or 2 GiB */ }; - - uart3_clk: uart3-clk { - compatible = "fixed-clock"; - clock-frequency = <921600>; - #clock-cells = <0>; - }; }; &timer { @@ -39,5 +33,4 @@ &uart3 { status = "okay"; - clocks = <&uart3_clk>; }; diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index 5d5ad9db549b..ac3d04c75dd5 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -131,6 +131,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0120000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART0>; status = "disabled"; }; @@ -138,6 +139,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0122000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART1>; status = "disabled"; }; @@ -145,6 +147,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0124000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART2>; status = "disabled"; }; @@ -152,6 +155,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0126000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART3>; status = "disabled"; }; @@ -159,6 +163,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb0128000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART4>; status = "disabled"; }; @@ -166,6 +171,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb012a000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART5>; status = "disabled"; }; @@ -173,6 +179,7 @@ compatible = "actions,s500-uart", "actions,owl-uart"; reg = <0xb012c000 0x2000>; interrupts = ; + clocks = <&cmu CLK_UART6>; status = "disabled"; }; From 0c2e4ecb12ce7c7f600089c1b211858672eebb80 Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:18 +0200 Subject: [PATCH 059/584] arm: dts: owl-s500: Add Reset controller Add reset controller property and bindings header for the Actions Semi S500 SoC DTS. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index ac3d04c75dd5..a57ce7d6d745 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -8,6 +8,7 @@ #include #include #include +#include / { compatible = "actions,s500"; @@ -188,6 +189,7 @@ reg = <0xb0160000 0x8000>; clocks = <&hosc>, <&losc>; #clock-cells = <1>; + #reset-cells = <1>; }; timer: timer@b0168000 { From 2cfb1b3f251e41ab7316762585e376a9b3b348cd Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:21 +0200 Subject: [PATCH 060/584] arm: dts: owl-s500: Add DMA controller Add DMA controller node for Actions Semi S500 SoC. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index a57ce7d6d745..449e9807c4ec 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -207,5 +207,19 @@ reg = <0xb01b0100 0x100>; #power-domain-cells = <1>; }; + + dma: dma-controller@b0260000 { + compatible = "actions,s500-dma"; + reg = <0xb0260000 0xd00>; + interrupts = , + , + , + ; + #dma-cells = <1>; + dma-channels = <12>; + dma-requests = <46>; + clocks = <&cmu CLK_DMAC>; + power-domains = <&sps S500_PD_DMA>; + }; }; }; From b846f3febbb3fd3623d8c6a0942934a1d527ef7e Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:22 +0200 Subject: [PATCH 061/584] arm: dts: owl-s500: Add pinctrl & GPIO support Add pinctrl node for Actions Semi S500 SoC. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index 449e9807c4ec..b16172615db0 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -6,6 +6,7 @@ */ #include +#include #include #include #include @@ -208,6 +209,25 @@ #power-domain-cells = <1>; }; + pinctrl: pinctrl@b01b0000 { + compatible = "actions,s500-pinctrl"; + reg = <0xb01b0000 0x40>, /* GPIO */ + <0xb01b0040 0x10>, /* Multiplexing Control */ + <0xb01b0060 0x18>, /* PAD Control */ + <0xb01b0080 0xc>; /* PAD Drive Capacity */ + clocks = <&cmu CLK_GPIO>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 132>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = , /* GPIOA */ + , /* GPIOB */ + , /* GPIOC */ + , /* GPIOD */ + ; /* GPIOE */ + }; + dma: dma-controller@b0260000 { compatible = "actions,s500-dma"; reg = <0xb0260000 0xd00>; From 481c640596bca29703ae290880eda3a3420dd4d1 Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:23 +0200 Subject: [PATCH 062/584] arm: dts: owl-s500: Add MMC support Add MMC controller nodes for Actions Semi S500 SoC, in order to facilitate access to SD/EMMC/SDIO cards. Signed-off-by: Cristian Ciocaltea Reviewed-by: Ulf Hansson Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index b16172615db0..7af7c9e1119d 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -241,5 +241,38 @@ clocks = <&cmu CLK_DMAC>; power-domains = <&sps S500_PD_DMA>; }; + + mmc0: mmc@b0230000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0230000 0x38>; + interrupts = ; + clocks = <&cmu CLK_SD0>; + resets = <&cmu RESET_SD0>; + dmas = <&dma 2>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc1: mmc@b0234000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0234000 0x38>; + interrupts = ; + clocks = <&cmu CLK_SD1>; + resets = <&cmu RESET_SD1>; + dmas = <&dma 3>; + dma-names = "mmc"; + status = "disabled"; + }; + + mmc2: mmc@b0238000 { + compatible = "actions,s500-mmc", "actions,owl-mmc"; + reg = <0xb0238000 0x38>; + interrupts = ; + clocks = <&cmu CLK_SD2>; + resets = <&cmu RESET_SD2>; + dmas = <&dma 4>; + dma-names = "mmc"; + status = "disabled"; + }; }; }; From 83ba46e312a1e22c63ae3ca01f91d94ac6b3d70c Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:24 +0200 Subject: [PATCH 063/584] arm: dts: owl-s500: Add I2C support Add I2C controller nodes for Actions Semi S500 SoC. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 40 +++++++++++++++++++++++++++++++++ 1 file changed, 40 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index 7af7c9e1119d..55f8b8c2e149 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -193,6 +193,46 @@ #reset-cells = <1>; }; + i2c0: i2c@b0170000 { + compatible = "actions,s500-i2c"; + reg = <0xb0170000 0x4000>; + clocks = <&cmu CLK_I2C0>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@b0174000 { + compatible = "actions,s500-i2c"; + reg = <0xb0174000 0x4000>; + clocks = <&cmu CLK_I2C1>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@b0178000 { + compatible = "actions,s500-i2c"; + reg = <0xb0178000 0x4000>; + clocks = <&cmu CLK_I2C2>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@b017c000 { + compatible = "actions,s500-i2c"; + reg = <0xb017c000 0x4000>; + clocks = <&cmu CLK_I2C3>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>; From 3f435fba46c812129253a651004b3bce8ea20f25 Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:25 +0200 Subject: [PATCH 064/584] arm: dts: owl-s500: Add SIRQ controller Add SIRQ controller node for Actions Semi S500 SoC. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500.dtsi b/arch/arm/boot/dts/owl-s500.dtsi index 55f8b8c2e149..cd635f222d26 100644 --- a/arch/arm/boot/dts/owl-s500.dtsi +++ b/arch/arm/boot/dts/owl-s500.dtsi @@ -233,6 +233,16 @@ status = "disabled"; }; + sirq: interrupt-controller@b01b0200 { + compatible = "actions,s500-sirq"; + reg = <0xb01b0200 0x4>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = , /* SIRQ0 */ + , /* SIRQ1 */ + ; /* SIRQ2 */ + }; + timer: timer@b0168000 { compatible = "actions,s500-timer"; reg = <0xb0168000 0x8000>; From 8e23902d12433bf19be7e261eb02d64c27384901 Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:26 +0200 Subject: [PATCH 065/584] arm: dts: owl-s500-roseapplepi: Add uSD support Add uSD support for RoseapplePi SBC using a fixed regulator as a temporary solution until PMIC support becomes available. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500-roseapplepi.dts | 50 ++++++++++++++++++++++ 1 file changed, 50 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts index 800edf5d2d12..fe9ae3619422 100644 --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts @@ -14,6 +14,7 @@ model = "Roseapple Pi"; aliases { + mmc0 = &mmc0; serial2 = &uart2; }; @@ -25,6 +26,55 @@ device_type = "memory"; reg = <0x0 0x80000000>; /* 2GB */ }; + + /* Fixed regulator used in the absence of PMIC */ + sd_vcc: sd-vcc { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.1V"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; +}; + +&pinctrl { + mmc0_pins: mmc0-pins { + pinmux { + groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", + "sd0_cmd_mfp", "sd0_clk_mfp"; + function = "sd0"; + }; + + drv-pinconf { + groups = "sd0_d0_d3_drv", "sd0_cmd_drv", "sd0_clk_drv"; + drive-strength = <8>; + }; + + bias0-pinconf { + pins = "sd0_d0", "sd0_d1", "sd0_d2", + "sd0_d3", "sd0_cmd"; + bias-pull-up; + }; + + bias1-pinconf { + pins = "sd0_clk"; + bias-pull-down; + }; + }; +}; + +/* uSD */ +&mmc0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + no-sdio; + no-mmc; + no-1-8-v; + cd-gpios = <&pinctrl 117 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&sd_vcc>; + vqmmc-supply = <&sd_vcc>; }; &twd_timer { From 7b69552264aca925e8550324027e4f10f8bf8c4f Mon Sep 17 00:00:00 2001 From: Cristian Ciocaltea Date: Tue, 29 Dec 2020 23:17:27 +0200 Subject: [PATCH 066/584] arm: dts: owl-s500-roseapplepi: Add I2C pinctrl configuration Add pinctrl definitions for the I2C controllers used in RoseapplePi SBC. For the moment enable only I2C0, which is used by the ATC2603C PMIC. Signed-off-by: Cristian Ciocaltea Reviewed-by: Manivannan Sadhasivam Signed-off-by: Manivannan Sadhasivam --- arch/arm/boot/dts/owl-s500-roseapplepi.dts | 44 ++++++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm/boot/dts/owl-s500-roseapplepi.dts b/arch/arm/boot/dts/owl-s500-roseapplepi.dts index fe9ae3619422..ff91561ca99c 100644 --- a/arch/arm/boot/dts/owl-s500-roseapplepi.dts +++ b/arch/arm/boot/dts/owl-s500-roseapplepi.dts @@ -37,7 +37,51 @@ }; }; +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; +}; + +&i2c1 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; +}; + +&i2c2 { + status = "disabled"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; +}; + &pinctrl { + i2c0_pins: i2c0-pins { + pinmux { + groups = "i2c0_mfp"; + function = "i2c0"; + }; + + pinconf { + pins = "i2c0_sclk", "i2c0_sdata"; + bias-pull-up; + }; + }; + + i2c1_pins: i2c1-pins { + pinconf { + pins = "i2c1_sclk", "i2c1_sdata"; + bias-pull-up; + }; + }; + + i2c2_pins: i2c2-pins { + pinconf { + pins = "i2c2_sclk", "i2c2_sdata"; + bias-pull-up; + }; + }; + mmc0_pins: mmc0-pins { pinmux { groups = "sd0_d0_mfp", "sd0_d1_mfp", "sd0_d2_d3_mfp", From 7193542331435f63010d9d1bbe05405c5398aed3 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Thu, 26 Nov 2020 14:01:37 +0530 Subject: [PATCH 067/584] dt-bindings: arm: qcom: Document SDX55 platform and boards Document the SDX55 platform binding and also the boards using it. Reviewed-by: Rob Herring Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20201126083138.47047-2-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index c97d4a580f47..f4af99b5b9af 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -40,6 +40,7 @@ description: | sdm630 sdm660 sdm845 + sdx55 sm8250 The 'board' element must be one of the following strings: @@ -167,6 +168,11 @@ properties: - xiaomi,lavender - const: qcom,sdm660 + - items: + - enum: + - qcom,sdx55-mtp + - const: qcom,sdx55 + - items: - enum: - qcom,ipq6018-cp01-c1 From 9d038b2e62defb58a77947b486993e018e37aff1 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Thu, 26 Nov 2020 14:01:38 +0530 Subject: [PATCH 068/584] ARM: dts: qcom: Add SDX55 platform and MTP board support Add basic devicetree support for SDX55 platform and MTP board from Qualcomm. The SDX55 platform features an ARM Cortex A7 CPU which forms the Application Processor Sub System (APSS) along with standard Qualcomm peripherals like GCC, TLMM, BLSP, QPIC, and BAM etc... Also, there exists the networking parts such as IPA, MHI, PCIE-EP, EMAC, and Modem etc.. Currently, this basic devicetree support includes GCC, RPMh clock, INTC and Debug UART. Co-developed-by: Vinod Koul Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20201126083138.47047-3-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/Makefile | 3 +- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 27 ++++ arch/arm/boot/dts/qcom-sdx55.dtsi | 193 +++++++++++++++++++++++++++ 3 files changed, 222 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/qcom-sdx55-mtp.dts create mode 100644 arch/arm/boot/dts/qcom-sdx55.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..13a7cee00daf 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -927,7 +927,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-msm8974-sony-xperia-amami.dtb \ qcom-msm8974-sony-xperia-castor.dtb \ qcom-msm8974-sony-xperia-honami.dtb \ - qcom-mdm9615-wp8548-mangoh-green.dtb + qcom-mdm9615-wp8548-mangoh-green.dtb \ + qcom-sdx55-mtp.dtb dtb-$(CONFIG_ARCH_RDA) += \ rda8810pl-orangepi-2g-iot.dtb \ rda8810pl-orangepi-i96.dtb diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts new file mode 100644 index 000000000000..262660e6dd11 --- /dev/null +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved. + * Copyright (c) 2020, Linaro Ltd. + */ + +/dts-v1/; + +#include "qcom-sdx55.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. SDX55 MTP"; + compatible = "qcom,sdx55-mtp", "qcom,sdx55"; + qcom,board-id = <0x5010008 0x0>; + + aliases { + serial0 = &blsp1_uart3; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&blsp1_uart3 { + status = "ok"; +}; diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi new file mode 100644 index 000000000000..c236faf9726b --- /dev/null +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -0,0 +1,193 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * SDX55 SoC device tree source + * + * Copyright (c) 2018, The Linux Foundation. All rights reserved. + * Copyright (c) 2020, Linaro Ltd. + */ + +#include +#include +#include + +/ { + #address-cells = <1>; + #size-cells = <1>; + qcom,msm-id = <357 0x10000>, <368 0x10000>, <418 0x10000>; + interrupt-parent = <&intc>; + + memory { + device_type = "memory"; + reg = <0 0>; + }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x0>; + enable-method = "psci"; + }; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + soc: soc { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sdx55"; + reg = <0x100000 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; + }; + + blsp1_uart3: serial@831000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x00831000 0x200>; + interrupts = ; + clocks = <&gcc 30>, + <&gcc 9>; + clock-names = "core", "iface"; + status = "disabled"; + }; + + pdc: interrupt-controller@b210000 { + compatible = "qcom,sdx55-pdc", "qcom,pdc"; + reg = <0x0b210000 0x30000>; + qcom,pdc-ranges = <0 179 52>; + #interrupt-cells = <3>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + intc: interrupt-controller@17800000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + interrupt-parent = <&intc>; + #interrupt-cells = <3>; + reg = <0x17800000 0x1000>, + <0x17802000 0x1000>; + }; + + timer@17820000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x17820000 0x1000>; + clock-frequency = <19200000>; + + frame@17821000 { + frame-number = <0>; + interrupts = , + ; + reg = <0x17821000 0x1000>, + <0x17822000 0x1000>; + }; + + frame@17823000 { + frame-number = <1>; + interrupts = ; + reg = <0x17823000 0x1000>; + status = "disabled"; + }; + + frame@17824000 { + frame-number = <2>; + interrupts = ; + reg = <0x17824000 0x1000>; + status = "disabled"; + }; + + frame@17825000 { + frame-number = <3>; + interrupts = ; + reg = <0x17825000 0x1000>; + status = "disabled"; + }; + + frame@17826000 { + frame-number = <4>; + interrupts = ; + reg = <0x17826000 0x1000>; + status = "disabled"; + }; + + frame@17827000 { + frame-number = <5>; + interrupts = ; + reg = <0x17827000 0x1000>; + status = "disabled"; + }; + + frame@17828000 { + frame-number = <6>; + interrupts = ; + reg = <0x17828000 0x1000>; + status = "disabled"; + }; + + frame@17829000 { + frame-number = <7>; + interrupts = ; + reg = <0x17829000 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@17840000 { + compatible = "qcom,rpmh-rsc"; + reg = <0x17830000 0x10000>, <0x17840000 0x10000>; + reg-names = "drv-0", "drv-1"; + interrupts = , + ; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <1>; + qcom,tcs-config = , , + , ; + + rpmhcc: clock-controller { + compatible = "qcom,sdx55-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + }; + }; + + timer { + compatible = "arm,armv7-timer"; + interrupts = , + , + , + ; + clock-frequency = <19200000>; + }; +}; From 4a928b3b7c0f8a2ae382c3db3a78898877567786 Mon Sep 17 00:00:00 2001 From: Timon Baetz Date: Wed, 30 Dec 2020 20:53:03 +0000 Subject: [PATCH 069/584] ARM: dts: exynos: Fix charging regulator voltage and current for I9100 Set CHARGER current and CHARGER_CV voltage according to Galaxy S2 Epic 4G Touch SPH-D710 Android vendor sources [0,1]. Remove regulator-always-on. The regulator can be enabled and disabled based on extcon events. [0] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/power/max8997_charger_u1.c#L169-L170 [1] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/power/max8997_charger_u1.c#L390-L391 Signed-off-by: Timon Baetz Link: https://lore.kernel.org/r/20201230205139.1812366-7-timon.baetz@protonmail.com Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4210-i9100.dts | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts index a0c3bab382ae..2837ac05d9b4 100644 --- a/arch/arm/boot/dts/exynos4210-i9100.dts +++ b/arch/arm/boot/dts/exynos4210-i9100.dts @@ -562,15 +562,14 @@ charger_reg: CHARGER { regulator-name = "CHARGER"; - regulator-min-microamp = <60000>; - regulator-max-microamp = <2580000>; - regulator-always-on; + regulator-min-microamp = <200000>; + regulator-max-microamp = <950000>; }; chargercv_reg: CHARGER_CV { regulator-name = "CHARGER_CV"; - regulator-min-microvolt = <3800000>; - regulator-max-microvolt = <4100000>; + regulator-min-microvolt = <4200000>; + regulator-max-microvolt = <4200000>; regulator-always-on; }; From 3803f461bd28c1c817281348509399778633e82f Mon Sep 17 00:00:00 2001 From: Timon Baetz Date: Wed, 30 Dec 2020 20:53:11 +0000 Subject: [PATCH 070/584] ARM: dts: exynos: Add top-off charging regulator node for I9100 Value taken from Galaxy S2 Epic 4G Touch SPH-D710 Android vendor kernel [0] which always sets 200mA. Also rearrange regulators based on definition in max8997.h. [0] https://github.com/krzk/linux-vendor-backup/blob/samsung/galaxy-s2-epic-4g-touch-sph-d710-exynos4210-dump/drivers/power/sec_battery_u1.c#L1525 Signed-off-by: Timon Baetz Link: https://lore.kernel.org/r/20201230205139.1812366-8-timon.baetz@protonmail.com Signed-off-by: Krzysztof Kozlowski --- arch/arm/boot/dts/exynos4210-i9100.dts | 21 ++++++++++++++------- 1 file changed, 14 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts index 2837ac05d9b4..304a8ee2364c 100644 --- a/arch/arm/boot/dts/exynos4210-i9100.dts +++ b/arch/arm/boot/dts/exynos4210-i9100.dts @@ -560,6 +560,16 @@ regulator-boot-on; }; + EN32KHZ_AP { + regulator-name = "EN32KHZ_AP"; + regulator-always-on; + }; + + EN32KHZ_CP { + regulator-name = "EN32KHZ_CP"; + regulator-always-on; + }; + charger_reg: CHARGER { regulator-name = "CHARGER"; regulator-min-microamp = <200000>; @@ -573,13 +583,10 @@ regulator-always-on; }; - EN32KHZ_AP { - regulator-name = "EN32KHZ_AP"; - regulator-always-on; - }; - - EN32KHZ_CP { - regulator-name = "EN32KHZ_CP"; + CHARGER_TOPOFF { + regulator-name = "CHARGER_TOPOFF"; + regulator-min-microamp = <200000>; + regulator-max-microamp = <200000>; regulator-always-on; }; }; From fd159539f7b0dbfe0aa196c3182e44b9ba49edb8 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sat, 7 Nov 2020 08:48:08 -0600 Subject: [PATCH 071/584] dt-bindings: arm: fsl: Add beacon,imx8mn-beacon-kit Add beacon,imx8mn-beacon-kit to list of compatible options. Signed-off-by: Adam Ford Reviewed-by: Krzysztof Kozlowski Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 34000f7fbe02..cee74fc0c115 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -691,6 +691,7 @@ properties: - description: i.MX8MN based Boards items: - enum: + - beacon,imx8mn-beacon-kit # i.MX8MN Beacon Development Kit - fsl,imx8mn-ddr4-evk # i.MX8MN DDR4 EVK Board - fsl,imx8mn-evk # i.MX8MN LPDDR4 EVK Board - const: fsl,imx8mn From 36ca3c8ccb537ac6311b977e71040b493f168a63 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sat, 7 Nov 2020 08:48:09 -0600 Subject: [PATCH 072/584] arm64: dts: imx: Add Beacon i.MX8M Nano development kit Beacon Embeddedworks is launching a development kit based on the i.MX8M Nano SoC. The kit consists of a System on Module (SOM) + baseboard. The SOM has the SoC, eMMC, and Ethernet. The baseboard has an wm8962 audio CODEC, a PDM microphone, and a single USB OTG. The baseboard is capable of two different, mutually exclusive video outputs, so the common items are in the baseboard file. When the video becomes available, LVDS output will be added to this kit file, and a second kit file will be added to support HDMI. Signed-off-by: Adam Ford Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mn-beacon-baseboard.dtsi | 307 +++++++++++++ .../boot/dts/freescale/imx8mn-beacon-kit.dts | 19 + .../boot/dts/freescale/imx8mn-beacon-som.dtsi | 433 ++++++++++++++++++ 4 files changed, 760 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 6f0777ee6cd6..901d80086b47 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi new file mode 100644 index 000000000000..376ca8ff7213 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi @@ -0,0 +1,307 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Compass Electronics Group, LLC + */ + +/ { + leds { + compatible = "gpio-leds"; + + led-0 { + label = "gen_led0"; + gpios = <&pca6416_1 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-1 { + label = "gen_led1"; + gpios = <&pca6416_1 5 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "gen_led2"; + gpios = <&pca6416_1 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led3>; + label = "heartbeat"; + gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + reg_audio: regulator-audio { + compatible = "regulator-fixed"; + regulator-name = "3v3_aud"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pca6416_1 11 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + regulator-name = "vsd_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg_vbus: regulator-usb { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb_otg>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + sound { + compatible = "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + audio-cpu = <&sai3>; + audio-codec = <&wm8962>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "AMIC", "MICBIAS", + "IN3R", "AMIC"; + }; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_espi2>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; + + eeprom@0 { + compatible = "microchip,at25160bn", "atmel,at25"; + reg = <0>; + spi-max-frequency = <5000000>; + spi-cpha; + spi-cpol; + pagesize = <32>; + size = <2048>; + address-width = <16>; + }; +}; + +&i2c4 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + pca6416_0: gpio@20 { + compatible = "nxp,pcal6416"; + reg = <0x20>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcal6414>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + }; + + pca6416_1: gpio@21 { + compatible = "nxp,pcal6416"; + reg = <0x21>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gpio4>; + interrupts = <27 IRQ_TYPE_LEVEL_LOW>; + }; + + wm8962: audio-codec@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; + clocks = <&clk IMX8MN_CLK_SAI3_ROOT>; + clock-names = "xclk"; + DCVDD-supply = <®_audio>; + DBVDD-supply = <®_audio>; + AVDD-supply = <®_audio>; + CPVDD-supply = <®_audio>; + MICVDD-supply = <®_audio>; + PLLVDD-supply = <®_audio>; + SPKVDD1-supply = <®_audio>; + SPKVDD2-supply = <®_audio>; + gpio-cfg = < + 0x0000 /* 0:Default */ + 0x0000 /* 1:Default */ + 0x0000 /* 2:FN_DMICCLK */ + 0x0000 /* 3:Default */ + 0x0000 /* 4:FN_DMICCDAT */ + 0x0000 /* 5:Default */ + >; + }; +}; + +&easrc { + fsl,asrc-rate = <48000>; + status = "okay"; +}; + +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MN_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + fsl,sai-mclk-direction-output; + status = "okay"; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +&uart2 { /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + assigned-clocks = <&clk IMX8MN_CLK_UART3>; + assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usb_otg_vbus>; + disable-over-current; + dr_mode="otg"; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + bus-width = <4>; + vmmc-supply = <®_usdhc2_vmmc>; + status = "okay"; +}; + +&iomuxc { + pinctrl_espi2: espi2grp { + fsl,pins = < + MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x82 + MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x82 + MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x82 + MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x41 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MN_IOMUXC_I2C4_SCL_I2C4_SCL 0x400001c3 + MX8MN_IOMUXC_I2C4_SDA_I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_led3: led3grp { + fsl,pins = < + MX8MN_IOMUXC_SAI3_RXFS_GPIO4_IO28 0x41 + >; + }; + + pinctrl_pcal6414: pcal6414-gpiogrp { + fsl,pins = < + MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27 0x19 + >; + }; + + pinctrl_reg_usb_otg: reg-otggrp { + fsl,pins = < + MX8MN_IOMUXC_SAI3_RXC_GPIO4_IO29 0x19 + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX 0x40 + MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX 0x40 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MN_IOMUXC_SD2_CD_B_USDHC2_CD_B 0x41 + MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts b/arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts new file mode 100644 index 000000000000..1392ce02587b --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-kit.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Compass Electronics Group, LLC + */ + +/dts-v1/; + +#include "imx8mn.dtsi" +#include "imx8mn-beacon-som.dtsi" +#include "imx8mn-beacon-baseboard.dtsi" + +/ { + model = "Beacon EmbeddedWorks i.MX8M Nano Development Kit"; + compatible = "beacon,imx8mn-beacon-kit", "fsl,imx8mn"; + + chosen { + stdout-path = &uart2; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi new file mode 100644 index 000000000000..67e5e5b9ddea --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi @@ -0,0 +1,433 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2020 Compass Electronics Group, LLC + */ + +/ { + usdhc1_pwrseq: usdhc1_pwrseq { + compatible = "mmc-pwrseq-simple"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1_gpio>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; + clocks = <&osc_32k>; + clock-names = "ext_clock"; + post-power-on-delay-ms = <80>; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; +}; + +&A53_0 { + cpu-supply = <&buck2_reg>; +}; + +&A53_1 { + cpu-supply = <&buck2_reg>; +}; + +&A53_2 { + cpu-supply = <&buck2_reg>; +}; + +&A53_3 { + cpu-supply = <&buck2_reg>; +}; + +/* DDR controller is running LPDDR at 800MHz which requires 0.95V */ +&a53_opp_table { + opp-1200000000 { + opp-microvolt = <950000>; + }; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-800M { + opp-hz = /bits/ 64 <800000000>; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + phy-supply = <&buck6_reg>; + phy-reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@4b { + compatible = "rohm,bd71847"; + reg = <0x4b>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio1>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + rohm,reset-snvs-powered; + + regulators { + buck1_reg: BUCK1 { + regulator-name = "buck1"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + }; + + buck2_reg: BUCK2 { + regulator-name = "buck2"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1000000>; + rohm,dvs-idle-voltage = <900000>; + }; + + buck3_reg: BUCK3 { + // BUCK5 in datasheet + regulator-name = "buck3"; + regulator-min-microvolt = <700000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + // BUCK6 in datasheet + regulator-name = "buck4"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5_reg: BUCK5 { + // BUCK7 in datasheet + regulator-name = "buck5"; + regulator-min-microvolt = <1605000>; + regulator-max-microvolt = <1995000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + // BUCK8 in datasheet + regulator-name = "buck6"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1_reg: LDO1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <900000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "ldo6"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + eeprom@50 { + compatible = "microchip,24c64", "atmel,24c64"; + pagesize = <32>; + read-only; /* Manufacturing EEPROM programmed at factory */ + reg = <0x50>; + }; + + rtc@51 { + compatible = "nxp,pcf85263"; + reg = <0x51>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + assigned-clocks = <&clk IMX8MN_CLK_UART1>; + assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm43438-bt"; + shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; + host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; + device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>; + clocks = <&osc_32k>; + max-speed = <4000000>; + clock-names = "extclk"; + }; +}; + +&usdhc1 { + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <4>; + non-removable; + cap-power-off-card; + pm-ignore-notify; + keep-power-in-suspend; + mmc-pwrseq = <&usdhc1_pwrseq>; + status = "okay"; + + brcmf: bcrmf@1 { + reg = <1>; + compatible = "brcm,bcm4329-fmac"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wlan>; + interrupt-parent = <&gpio2>; + interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host-wake"; + }; +}; + +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MN_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MN_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicirqgrp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + MX8MN_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 + MX8MN_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 + MX8MN_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19 + MX8MN_IOMUXC_SD1_DATA5_GPIO2_IO7 0x19 + MX8MN_IOMUXC_SD1_DATA6_GPIO2_IO8 0x19 + MX8MN_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141 + >; + }; + + pinctrl_usdhc1_gpio: usdhc1gpiogrp { + fsl,pins = < + MX8MN_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 + MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 + MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; + + pinctrl_wlan: wlangrp { + fsl,pins = < + MX8MN_IOMUXC_SD1_DATA7_GPIO2_IO9 0x111 + >; + }; +}; From 397546ac9c22c5899522181aa46297129e7e533e Mon Sep 17 00:00:00 2001 From: Michael Klein Date: Wed, 2 Dec 2020 20:51:47 +0100 Subject: [PATCH 073/584] ARM: dts: sun6i-a31s-sinovoip-bpi-m2: add gpio-line-names Add gpio-line-names as documented on gitbooks [1] and in the schematics [2]. [1]: https://bananapi.gitbook.io/bpi-m2/en/bpi-m2_gpio_pin_define [2]: https://drive.google.com/file/d/0B4PAo2nW2KfnRERWNnJGSGxJbmM/view Signed-off-by: Michael Klein Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201202195144.2105036-1-michael@fossekall.de --- .../boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 71 +++++++++++++++++++ 1 file changed, 71 insertions(+) diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts index 708caee52425..367006fb280d 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts @@ -261,3 +261,74 @@ &usbphy { status = "okay"; }; + +&pio { + gpio-line-names = + /* PA */ + "ETXD0", "ETXD1", "ETXD2", "ETXD3", "SDC0-DET", "", "", + "", "ETXCLK", "ETXEN", "EGTXCLK", "ERXD0", "ERXD1", + "ERXD2", "ERXD3", "", "", "", "", "ERXDV", "ERXCK", + "ETXERR", "ERXERR", "ECOL", "ECRS", "ECLKIN", "EMDC", + "EMDIO", "", "", "", "", + + /* PB */ + "CN7-P29", "CN7-P31", "CN7-P33", "CN7-P35", "CN7-P37", + "CN7-P28", "CN7-P27", "CN7-P32", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", + + /* PC */ + "", "", "", "", "", "", "WL-SDIO-CMD", "WL-SDIO-CLK", + "WL-SDIO-D0", "WL-SDIO-D2", "WL-SDIO-D2", "WL-SDIO-D3", + "", "", "", "", "", "", "", "", "", "", "", "", "", "", + "", "USB-DRV", "", "", "", "", + + /* PD */ + "CN9-P09", "CN9-P11", "CN9-P13", "CN9-P15", "CN9-P17", + "CN9-P19", "CN9-P21", "CN9-P23", "CN9-P25", "CN9-P27", + "CN9-P29", "CN9-P31", "CN9-P33", "CN9-P35", "CN9-P37", + "CN9-P39", "CN9-P40", "CN9-P38", "CN9-P36", "CN9-P34", + "CN9-P32", "CN9-P30", "CN9-P28", "CN9-P26", "CN9-P22", + "CN9-P14", "CN9-P18", "CN9-P16", "", "", "", "", + + /* PE */ + "CN6-P20", "CN6-P24", "CN6-P30", "CN6-P28", "CN7-P08", + "CN7-P10", "CN7-P36", "CN7-P38", "CN6-P17", "CN6-P19", + "CN6-P21", "CN6-P23", "CN6-P25", "CN6-P27", "CN6-P29", + "CN6-P31", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", + + /* PF */ + "SDC0-D1", "SDC0-D0", "SDC0-CLK", "SDC0-CMD", "SDC0-D3", + "SDC0-D2", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", "", "", "", "", + "", + + /* PG */ + "CN9-P06", "CN9-P08", "CN9-P20", "CN9-P12", "CN9-P07", + "LED-PWR", "CN7-P13", "CN7-P11", "CN7-P22", "CN7-P15", + "LED-G", "LED-B", "CN7-P26", "CN7-P24", "CN7-P23", + "CN7-P19", "CN7-P21", "HCEC", "CN6-P22", "", "", "", "", + "", "", "", "", "", "", "", "", "", + + /* PH */ + "", "", "", "", "", "", "", "", "", "CN7-P07", + "CN7-P12", "CN7-P16", "CN7-P18", "CN9-P10", "CN6-P16", + "CN6-P14", "CN9-P04", "CN9-P02", "CN7-P05", "CN7-P03", + "CN8-P03", "CN8-P02", "", "", "CN6-P34", "CN6-P32", + "CN6-P26", "CN6-P18", "", "", "", ""; +}; + +&r_pio { + gpio-line-names = + /* PL */ + "PMU-SCK", "PMU-SDA", "VBAT-EN", "", "IR-RX", + "WL-WAKE-HOST", "BT-WAKE_HOST", "BT-ENABLE", + "WL-PMU-EN", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", "", "", + + /* PM */ + "CN6-P12", "CN6-P35", "CN7-P40", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", ""; +}; From 62b3c680cfdc1f60a9143a1e4aabff7473629157 Mon Sep 17 00:00:00 2001 From: Jisheng Zhang Date: Mon, 9 Nov 2020 17:03:35 +0800 Subject: [PATCH 074/584] arm64: dts: socfpga: Use generic "ngpios" rather than "snps,nr-gpios" This is to remove similar errors as below: OF: /.../gpio-port@0: could not find phandle Commit 7569486d79ae ("gpio: dwapb: Add ngpios DT-property support") explained the reason of above errors well and added the generic "ngpios" property, let's use it. Signed-off-by: Jisheng Zhang Reviewed-by: Linus Walleij Signed-off-by: Dinh Nguyen --- arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi index 0f893984c256..d301ac0d406b 100644 --- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi @@ -203,7 +203,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <24>; + ngpios = <24>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; @@ -223,7 +223,7 @@ compatible = "snps,dw-apb-gpio-port"; gpio-controller; #gpio-cells = <2>; - snps,nr-gpios = <24>; + ngpios = <24>; reg = <0>; interrupt-controller; #interrupt-cells = <2>; From a427485a009348f0c7a498e34788a4c5adcc7128 Mon Sep 17 00:00:00 2001 From: Dinh Nguyen Date: Mon, 7 Dec 2020 14:43:01 -0600 Subject: [PATCH 075/584] arm64: dts: n5x: Add support for Intel's eASIC N5X platform The Intel eASIC N5X platform shares the same register map as the Agilex platform, thus, we can re-use the socfpga_agilex.dtsi as the base DTSI. Signed-off-by: Dinh Nguyen --- arch/arm64/Kconfig.platforms | 5 ++ arch/arm64/boot/dts/intel/Makefile | 1 + .../boot/dts/intel/socfpga_n5x_socdk.dts | 53 +++++++++++++++++++ 3 files changed, 59 insertions(+) create mode 100644 arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms index 6eecdef538bd..c20eacd9a931 100644 --- a/arch/arm64/Kconfig.platforms +++ b/arch/arm64/Kconfig.platforms @@ -13,6 +13,11 @@ config ARCH_AGILEX help This enables support for Intel's Agilex SoCFPGA Family. +config ARCH_N5X + bool "Intel's eASIC N5X SoCFPGA Family" + help + This enables support for Intel's eASIC N5X SoCFPGA Family. + config ARCH_SUNXI bool "Allwinner sunxi 64-bit SoC Family" select ARCH_HAS_RESET_CONTROLLER diff --git a/arch/arm64/boot/dts/intel/Makefile b/arch/arm64/boot/dts/intel/Makefile index 296eceec4276..3a052540605b 100644 --- a/arch/arm64/boot/dts/intel/Makefile +++ b/arch/arm64/boot/dts/intel/Makefile @@ -2,3 +2,4 @@ dtb-$(CONFIG_ARCH_AGILEX) += socfpga_agilex_socdk.dtb \ socfpga_agilex_socdk_nand.dtb dtb-$(CONFIG_ARCH_KEEMBAY) += keembay-evm.dtb +dtb-$(CONFIG_ARCH_N5X) += socfpga_n5x_socdk.dtb diff --git a/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts new file mode 100644 index 000000000000..5f56e2697fee --- /dev/null +++ b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts @@ -0,0 +1,53 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021, Intel Corporation + */ +#include "socfpga_agilex.dtsi" + +/ { + model = "eASIC N5X SoCDK"; + + aliases { + serial0 = &uart0; + ethernet0 = &gmac0; + ethernet1 = &gmac1; + ethernet2 = &gmac2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + device_type = "memory"; + /* We expect the bootloader to fill in the reg */ + reg = <0 0 0 0>; + }; + + soc { + clocks { + osc1 { + clock-frequency = <25000000>; + }; + }; + }; +}; + +&clkmgr { + compatible = "intel,easic-n5x-clkmgr"; +}; + +&mmc { + status = "okay"; + cap-sd-highspeed; + broken-cd; + bus-width = <4>; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog0 { + status = "okay"; +}; From 3f8c61a567ebc4c03caba2730352833edc16b132 Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:06 +0800 Subject: [PATCH 076/584] arm64: dts: ls1043a: add DT node for external interrupt lines Add device-tree node for external interrupt lines IRQ0-IRQ11. Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi index bbae4b353d3f..12bd1263158f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi @@ -311,6 +311,31 @@ compatible = "fsl,ls1043a-scfg", "syscon"; reg = <0x0 0x1570000 0x0 0x10000>; big-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1570000 0x10000>; + + extirq: interrupt-controller@1ac { + compatible = "fsl,ls1043a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1ac 4>; + interrupt-map = + <0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <8 0 &gic GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + <9 0 &gic GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>, + <10 0 &gic GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, + <11 0 &gic GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; }; crypto: crypto@1700000 { From 7968344126e562be585d944be52bfc42e0760a7d Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:07 +0800 Subject: [PATCH 077/584] arm64: dts: ls1046a: add DT node for external interrupt lines Add device-tree node for external interrupt lines IRQ0-IRQ11. Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 25 +++++++++++++++++++ 1 file changed, 25 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi index 025e1f587662..d3f5e48c58dd 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi @@ -314,6 +314,31 @@ compatible = "fsl,ls1046a-scfg", "syscon"; reg = <0x0 0x1570000 0x0 0x10000>; big-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1570000 0x10000>; + + extirq: interrupt-controller@1ac { + compatible = "fsl,ls1046a-extirq", "fsl,ls1043a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1ac 4>; + interrupt-map = + <0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <8 0 &gic GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, + <9 0 &gic GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>, + <10 0 &gic GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, + <11 0 &gic GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; }; crypto: crypto@1700000 { From c4a462485aee3de2c3b33395c0c88ba9526144d6 Mon Sep 17 00:00:00 2001 From: Hou Zhiqiang Date: Mon, 30 Nov 2020 18:15:08 +0800 Subject: [PATCH 078/584] arm64: dts: ls1046ardb: Add interrupt line for RTC node Add interrupt line for RTC node, which is low level active. Signed-off-by: Hou Zhiqiang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts index d53ccc56bb63..60acdf0b689e 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-rdb.dts @@ -3,6 +3,7 @@ * Device Tree Include file for Freescale Layerscape-1046A family SoC. * * Copyright 2016 Freescale Semiconductor, Inc. + * Copyright 2019-2020 NXP * * Mingkai Hu */ @@ -74,6 +75,8 @@ rtc@51 { compatible = "nxp,pcf2129"; reg = <0x51>; + /* IRQ_RTC_B -> IRQ05, active low */ + interrupts-extended = <&extirq 5 IRQ_TYPE_LEVEL_LOW>; }; }; From 0e88b5fd565da96375672ae547af5cdba46fdc0d Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:09 +0800 Subject: [PATCH 079/584] arm64: dts: ls1088a: add DT node for external interrupt lines Add device-tree node for external interrupt lines IRQ0-IRQ11. Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi index 6403455ed039..ee0354928f6b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi @@ -220,6 +220,37 @@ little-endian; }; + isc: syscon@1f70000 { + compatible = "fsl,ls1088a-isc", "syscon"; + reg = <0x0 0x1f70000 0x0 0x10000>; + little-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1f70000 0x10000>; + + extirq: interrupt-controller@14 { + compatible = "fsl,ls1088a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x14 4>; + interrupt-map = + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; + }; + tmu: tmu@1f80000 { compatible = "fsl,qoriq-tmu"; reg = <0x0 0x1f80000 0x0 0x10000>; From 09b19ef878265e70e9b9cde283d41d66695e4cbe Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:10 +0800 Subject: [PATCH 080/584] arm64: dts: ls1088ardb: fix interrupt line for RTC node Fix interrupt line for RTC node on ls1088ardb Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts index 528ec72d0b83..bf7b43ab1293 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-rdb.dts @@ -2,7 +2,7 @@ /* * Device Tree file for NXP LS1088A RDB Board. * - * Copyright 2017 NXP + * Copyright 2017-2020 NXP * * Harninder Rai * @@ -158,8 +158,8 @@ rtc@51 { compatible = "nxp,pcf2129"; reg = <0x51>; - /* IRQ10_B */ - interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + /* IRQ_RTC_B -> IRQ0_B(CPLD) -> IRQ00(CPU), active low */ + interrupts-extended = <&extirq 0 IRQ_TYPE_LEVEL_LOW>; }; }; }; From ebb0713736ac98845178e81c0ae3ca3f2f11d3fb Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:11 +0800 Subject: [PATCH 081/584] arm64: dts: ls208xa: add DT node for external interrupt lines Add device-tree node for external interrupt lines IRQ0-IRQ11. Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 33 ++++++++++++++++++- 1 file changed, 32 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi index c68901f8c6f0..767e3710bff2 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -3,7 +3,7 @@ * Device Tree Include file for Freescale Layerscape-2080A family SoC. * * Copyright 2016 Freescale Semiconductor, Inc. - * Copyright 2017 NXP + * Copyright 2017-2020 NXP * * Abhimanyu Saini * @@ -277,6 +277,37 @@ little-endian; }; + isc: syscon@1f70000 { + compatible = "fsl,ls2080a-isc", "syscon"; + reg = <0x0 0x1f70000 0x0 0x10000>; + little-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1f70000 0x10000>; + + extirq: interrupt-controller@14 { + compatible = "fsl,ls2080a-extirq", "fsl,ls1088a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x14 4>; + interrupt-map = + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; + }; + tmu: tmu@1f80000 { compatible = "fsl,qoriq-tmu"; reg = <0x0 0x1f80000 0x0 0x10000>; From 6f5851a866b254b404cd7f50a24af0677a6b9fc3 Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:12 +0800 Subject: [PATCH 082/584] arm64: dts: ls208xa-rdb: add interrupt line for RTC node Add interrupt line for RTC node on ls208xa-rdb Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi index d0d670227ae2..4b71c4fcb35f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi @@ -3,7 +3,7 @@ * Device Tree file for Freescale LS2080A RDB Board. * * Copyright 2016 Freescale Semiconductor, Inc. - * Copyright 2017 NXP + * Copyright 2017-2020 NXP * * Abhimanyu Saini * @@ -56,6 +56,8 @@ rtc@68 { compatible = "dallas,ds3232"; reg = <0x68>; + /* IRQ_RTC_B -> IRQ06, active low */ + interrupts-extended = <&extirq 6 IRQ_TYPE_LEVEL_LOW>; }; }; From 332b6a79b415e8b96b8dd87d4e8973192882d6a6 Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:13 +0800 Subject: [PATCH 083/584] arm64: dts: lx2160a: add DT node for external interrupt lines Add device-tree node for external interrupt lines IRQ0-IRQ11. Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi index 197397777c83..0d4bce13b8f1 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi @@ -664,6 +664,37 @@ little-endian; }; + isc: syscon@1f70000 { + compatible = "fsl,lx2160a-isc", "syscon"; + reg = <0x0 0x1f70000 0x0 0x10000>; + little-endian; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x1f70000 0x10000>; + + extirq: interrupt-controller@14 { + compatible = "fsl,lx2160a-extirq", "fsl,ls1088a-extirq"; + #interrupt-cells = <2>; + #address-cells = <0>; + interrupt-controller; + reg = <0x14 4>; + interrupt-map = + <0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, + <2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, + <3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, + <4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, + <5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, + <6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, + <7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, + <8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-map-mask = <0xffffffff 0x0>; + }; + }; + tmu: tmu@1f80000 { compatible = "fsl,qoriq-tmu"; reg = <0x0 0x1f80000 0x0 0x10000>; From a430c3d2f0afd88466a0871bc876ec5246b8e09e Mon Sep 17 00:00:00 2001 From: Biwen Li Date: Mon, 30 Nov 2020 18:15:14 +0800 Subject: [PATCH 084/584] arm64: dts: lx2160ardb: fix interrupt line for RTC node Fix interrupt line for RTC node on lx2160ardb Signed-off-by: Biwen Li Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts index 7723ad5efd37..eb88de7f3a9c 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts @@ -2,7 +2,7 @@ // // Device Tree file for LX2160ARDB // -// Copyright 2018 NXP +// Copyright 2018-2020 NXP /dts-v1/; @@ -175,8 +175,8 @@ rtc@51 { compatible = "nxp,pcf2129"; reg = <0x51>; - // IRQ10_B - interrupts = <0 150 0x4>; + /* IRQ_RTC_B -> IRQ08, active low */ + interrupts-extended = <&extirq 8 IRQ_TYPE_LEVEL_LOW>; }; }; From 9c2eb8b7be78a0de6705ef543bd83514c56c6580 Mon Sep 17 00:00:00 2001 From: Yangbo Lu Date: Tue, 5 Jan 2021 11:32:59 +0800 Subject: [PATCH 085/584] arm64: dts: freescale: use fixed index mmcN for NXP layerscape reference boards The eSDHC driver has converted to use asynchronous probe. Let's use fixed index mmcN for eSDHC controllers, so that we can ignore the effect on usage, and avoid problem on previous use cases with fixed index mmcblkN. Signed-off-by: Yangbo Lu Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts | 5 +++++ arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 5 +++++ arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts | 2 ++ arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts | 2 ++ arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts | 2 ++ 5 files changed, 16 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts index 449475a97bf1..e22c5e77fecd 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts @@ -13,6 +13,11 @@ model = "LS1012A QDS Board"; compatible = "fsl,ls1012a-qds", "fsl,ls1012a"; + aliases { + mmc0 = &esdhc0; + mmc1 = &esdhc1; + }; + sys_mclk: clock-mclk { compatible = "fixed-clock"; #clock-cells = <0>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts index d45c17620b98..f939d656898b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts @@ -12,6 +12,11 @@ / { model = "LS1012A RDB Board"; compatible = "fsl,ls1012a-rdb", "fsl,ls1012a"; + + aliases { + mmc0 = &esdhc0; + mmc1 = &esdhc1; + }; }; &duart0 { diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts index 2d1fe6c3797f..16ae3b00cf48 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts @@ -14,6 +14,8 @@ aliases { crypto = &crypto; + mmc0 = &esdhc0; + mmc1 = &esdhc1; serial0 = &uart0; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts index eb88de7f3a9c..6f82759f0ce4 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts @@ -14,6 +14,8 @@ aliases { crypto = &crypto; + mmc0 = &esdhc0; + mmc1 = &esdhc1; serial0 = &uart0; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts index 91786848bd30..e1defee1ad27 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts @@ -14,6 +14,8 @@ aliases { crypto = &crypto; + mmc0 = &esdhc0; + mmc1 = &esdhc1; serial0 = &uart0; }; From 066d21bcf605727814af2a4d44e96ba578f9103d Mon Sep 17 00:00:00 2001 From: Danny Lin Date: Sun, 20 Dec 2020 16:29:05 -0800 Subject: [PATCH 086/584] arm64: dts: qcom: sm8150: Define CPU topology sm8150 has a big.LITTLE CPU setup with DynamIQ, so all cores are within the same CPU cluster and LLC (Last-Level Cache) domain. Define this topology to help the scheduler make decisions. Signed-off-by: Danny Lin Link: https://lore.kernel.org/r/20201221002907.2870059-2-danny@kdrag0n.dev Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 36 ++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 5270bda7418f..d2159b1aa97e 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -157,6 +157,42 @@ next-level-cache = <&L3_0>; }; }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + + core2 { + cpu = <&CPU2>; + }; + + core3 { + cpu = <&CPU3>; + }; + + core4 { + cpu = <&CPU4>; + }; + + core5 { + cpu = <&CPU5>; + }; + + core6 { + cpu = <&CPU6>; + }; + + core7 { + cpu = <&CPU7>; + }; + }; + }; }; firmware { From 81188f585d023f6bf403cb1c79e5037dfd5819ff Mon Sep 17 00:00:00 2001 From: Danny Lin Date: Sun, 20 Dec 2020 16:29:06 -0800 Subject: [PATCH 087/584] arm64: dts: qcom: sm8150: Add PSCI idle states Like other Qualcomm SoCs, sm8150 exposes CPU and cluster idle states through PSCI. Define the idle states to save power when the CPU is not in active use. These idle states, latency, and residency values match the downstream 4.14 kernel from Qualcomm as of LA.UM.8.1.r1-15600-sm8150.0. It's worth noting that the CPU has an additional C3 power collapse idle state between WFI and rail power collapse (with PSCI mode 0x40000003), but it is not officially used in downstream kernels due to "thermal throttling issues." Signed-off-by: Danny Lin Link: https://lore.kernel.org/r/20201221002907.2870059-3-danny@kdrag0n.dev Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 50 ++++++++++++++++++++++++++++ 1 file changed, 50 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index d2159b1aa97e..1b10bc80e483 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -47,6 +47,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x0>; enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -64,6 +66,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x100>; enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -79,6 +83,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x200>; enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -93,6 +99,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x300>; enable-method = "psci"; + cpu-idle-states = <&LITTLE_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -107,6 +115,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x400>; enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -121,6 +131,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x500>; enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -135,6 +147,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x600>; enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -149,6 +163,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x700>; enable-method = "psci"; + cpu-idle-states = <&BIG_CPU_SLEEP_0 + &CLUSTER_SLEEP_0>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; #cooling-cells = <2>; @@ -193,6 +209,40 @@ }; }; }; + + idle-states { + entry-method = "psci"; + + LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 { + compatible = "arm,idle-state"; + idle-state-name = "little-rail-power-collapse"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <355>; + exit-latency-us = <909>; + min-residency-us = <3934>; + local-timer-stop; + }; + + BIG_CPU_SLEEP_0: cpu-sleep-1-0 { + compatible = "arm,idle-state"; + idle-state-name = "big-rail-power-collapse"; + arm,psci-suspend-param = <0x40000004>; + entry-latency-us = <241>; + exit-latency-us = <1461>; + min-residency-us = <4488>; + local-timer-stop; + }; + + CLUSTER_SLEEP_0: cluster-sleep-0 { + compatible = "arm,idle-state"; + idle-state-name = "cluster-power-collapse"; + arm,psci-suspend-param = <0x400000F4>; + entry-latency-us = <3263>; + exit-latency-us = <6562>; + min-residency-us = <9987>; + local-timer-stop; + }; + }; }; firmware { From 5b2dae72187de25a90f245482281a9ed0ffd268f Mon Sep 17 00:00:00 2001 From: Danny Lin Date: Sun, 20 Dec 2020 16:29:07 -0800 Subject: [PATCH 088/584] arm64: dts: qcom: sm8150: Add CPU capacities and energy model MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Power and performance measurements were made using my freqbench [1] benchmark coordinator, which isolates, offlines, and disables the timer tick on test CPUs to maximize accuracy. It uses EEMBC CoreMark [2] as the workload and measures power usage using the PM8150B PMIC's fuel gauge. The energy model dynamic-power-coefficient values were calculated with DPC = µW / MHz / V^2 for each OPP, and averaged across all OPPs within each cluster for the final coefficient. Voltages were obtained from the qcom-cpufreq-hw driver that reads voltages from the OSM LUT programmed into the SoC. Normalized DMIPS/MHz capacity scale values for each CPU were calculated from CoreMarks/MHz (CoreMark iterations per second per MHz), which serves the same purpose. For each CPU, the final capacity-dmips-mhz value is the C/MHz value of its maximum frequency normalized to SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system. An Asus ZenFone 6 device running a downstream Qualcomm 4.14 kernel (LA.UM.8.1.r1-15600-sm8150.0) was used for benchmarks to ensure proper frequency scaling and other low-level controls. Raw benchmark results can be found in the freqbench repository [3]. Below is a human-readable summary: Frequency domains: cpu1 cpu4 cpu7 Offline CPUs: cpu1 cpu2 cpu3 cpu4 cpu5 cpu6 cpu7 Baseline power usage: 1400 mW ===== CPU 1 ===== Frequencies: 300 403 499 576 672 768 844 940 1036 1113 1209 1305 1382 1478 1555 1632 1708 1785 300: 1114 3.7 C/MHz 52 mW 11.8 J 21.3 I/mJ 224.4 s 403: 1497 3.7 C/MHz 57 mW 9.5 J 26.2 I/mJ 167.0 s 499: 1854 3.7 C/MHz 73 mW 9.8 J 25.5 I/mJ 134.9 s 576: 2139 3.7 C/MHz 83 mW 9.7 J 25.8 I/mJ 116.9 s 672: 2495 3.7 C/MHz 65 mW 6.5 J 38.6 I/mJ 100.2 s 768: 2852 3.7 C/MHz 72 mW 6.3 J 39.4 I/mJ 87.7 s 844: 3137 3.7 C/MHz 77 mW 6.2 J 40.5 I/mJ 79.7 s 940: 3493 3.7 C/MHz 84 mW 6.0 J 41.8 I/mJ 71.6 s 1036: 3850 3.7 C/MHz 91 mW 5.9 J 42.5 I/mJ 64.9 s 1113: 4135 3.7 C/MHz 96 mW 5.8 J 43.2 I/mJ 60.5 s 1209: 4491 3.7 C/MHz 102 mW 5.7 J 44.2 I/mJ 55.7 s 1305: 4848 3.7 C/MHz 110 mW 5.7 J 44.0 I/mJ 51.6 s 1382: 5133 3.7 C/MHz 114 mW 5.5 J 45.2 I/mJ 48.7 s 1478: 5490 3.7 C/MHz 120 mW 5.5 J 45.7 I/mJ 45.5 s 1555: 5775 3.7 C/MHz 126 mW 5.5 J 45.8 I/mJ 43.3 s 1632: 6060 3.7 C/MHz 131 mW 5.4 J 46.1 I/mJ 41.3 s 1708: 6345 3.7 C/MHz 137 mW 5.4 J 46.3 I/mJ 39.4 s 1785: 6630 3.7 C/MHz 146 mW 5.5 J 45.5 I/mJ 37.7 s ===== CPU 4 ===== Frequencies: 710 825 940 1056 1171 1286 1401 1497 1612 1708 1804 1920 2016 2131 2227 2323 2419 710: 2765 3.9 C/MHz 126 mW 11.4 J 22.0 I/mJ 90.4 s 825: 6432 7.8 C/MHz 206 mW 8.0 J 31.2 I/mJ 38.9 s 940: 7331 7.8 C/MHz 227 mW 7.7 J 32.3 I/mJ 34.1 s 1056: 8227 7.8 C/MHz 249 mW 7.6 J 33.0 I/mJ 30.4 s 1171: 9127 7.8 C/MHz 261 mW 7.2 J 34.9 I/mJ 27.4 s 1286: 10020 7.8 C/MHz 289 mW 7.2 J 34.6 I/mJ 25.0 s 1401: 10918 7.8 C/MHz 311 mW 7.1 J 35.1 I/mJ 22.9 s 1497: 11663 7.8 C/MHz 336 mW 7.2 J 34.7 I/mJ 21.4 s 1612: 12546 7.8 C/MHz 375 mW 7.5 J 33.5 I/mJ 19.9 s 1708: 13320 7.8 C/MHz 398 mW 7.5 J 33.5 I/mJ 18.8 s 1804: 14069 7.8 C/MHz 456 mW 8.1 J 30.9 I/mJ 17.8 s 1920: 14909 7.8 C/MHz 507 mW 8.5 J 29.4 I/mJ 16.8 s 2016: 15706 7.8 C/MHz 558 mW 8.9 J 28.1 I/mJ 15.9 s 2131: 16612 7.8 C/MHz 632 mW 9.5 J 26.3 I/mJ 15.1 s 2227: 17349 7.8 C/MHz 698 mW 10.1 J 24.8 I/mJ 14.4 s 2323: 18088 7.8 C/MHz 717 mW 9.9 J 25.2 I/mJ 13.8 s 2419: 18835 7.8 C/MHz 845 mW 11.2 J 22.3 I/mJ 13.3 s ===== CPU 7 ===== Frequencies: 825 940 1056 1171 1286 1401 1497 1612 1708 1804 1920 2016 2131 2227 2323 2419 2534 2649 2745 2841 825: 3215 3.9 C/MHz 158 mW 12.3 J 20.3 I/mJ 77.8 s 940: 7330 7.8 C/MHz 269 mW 9.2 J 27.3 I/mJ 34.1 s 1056: 8227 7.8 C/MHz 291 mW 8.8 J 28.2 I/mJ 30.4 s 1171: 9125 7.8 C/MHz 316 mW 8.7 J 28.9 I/mJ 27.4 s 1286: 10024 7.8 C/MHz 338 mW 8.4 J 29.6 I/mJ 25.0 s 1401: 10922 7.8 C/MHz 365 mW 8.4 J 29.9 I/mJ 22.9 s 1497: 11674 7.8 C/MHz 383 mW 8.2 J 30.4 I/mJ 21.4 s 1612: 12564 7.8 C/MHz 406 mW 8.1 J 30.9 I/mJ 19.9 s 1708: 13317 7.8 C/MHz 427 mW 8.0 J 31.2 I/mJ 18.8 s 1804: 14062 7.8 C/MHz 446 mW 7.9 J 31.5 I/mJ 17.8 s 1920: 14966 7.8 C/MHz 498 mW 8.3 J 30.1 I/mJ 16.7 s 2016: 15711 7.8 C/MHz 513 mW 8.2 J 30.6 I/mJ 15.9 s 2131: 16599 7.8 C/MHz 599 mW 9.0 J 27.7 I/mJ 15.1 s 2227: 17353 7.8 C/MHz 622 mW 9.0 J 27.9 I/mJ 14.4 s 2323: 18095 7.8 C/MHz 704 mW 9.7 J 25.7 I/mJ 13.8 s 2419: 18849 7.8 C/MHz 738 mW 9.8 J 25.5 I/mJ 13.3 s 2534: 19761 7.8 C/MHz 824 mW 10.4 J 23.9 I/mJ 12.7 s 2649: 20658 7.8 C/MHz 882 mW 10.7 J 23.4 I/mJ 12.1 s 2745: 21400 7.8 C/MHz 1003 mW 11.7 J 21.3 I/mJ 11.7 s 2841: 22147 7.8 C/MHz 1092 mW 12.3 J 20.3 I/mJ 11.3 s [1] https://github.com/kdrag0n/freqbench [2] https://www.eembc.org/coremark/ [3] https://github.com/kdrag0n/freqbench/tree/master/results/sm8150/main Signed-off-by: Danny Lin Link: https://lore.kernel.org/r/20201221002907.2870059-4-danny@kdrag0n.dev Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 1b10bc80e483..84d3c8a0b7f1 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -47,6 +47,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x0>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_0>; @@ -66,6 +68,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x100>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_100>; @@ -83,6 +87,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x200>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_200>; @@ -99,6 +105,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x300>; enable-method = "psci"; + capacity-dmips-mhz = <488>; + dynamic-power-coefficient = <232>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_300>; @@ -115,6 +123,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x400>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <369>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_400>; @@ -131,6 +141,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x500>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <369>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_500>; @@ -147,6 +159,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x600>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <369>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_600>; @@ -163,6 +177,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x700>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <421>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &CLUSTER_SLEEP_0>; next-level-cache = <&L2_700>; From dea0e9bc0524f775442e56e4937fd5be854725c8 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:05 +0530 Subject: [PATCH 089/584] ARM: dts: qcom: sdx55: Add pincontrol node This adds pincontrol node to SDX55 dts. Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-2-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index c236faf9726b..913e558ae433 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -87,6 +87,16 @@ interrupt-controller; }; + tlmm: pinctrl@f100000 { + compatible = "qcom,sdx55-pinctrl"; + reg = <0xf100000 0x300000>; + interrupts = ; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + intc: interrupt-controller@17800000 { compatible = "qcom,msm-qgic2"; interrupt-controller; From ec99770d4b622b7f3e20d8db861cef59691ff128 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:06 +0530 Subject: [PATCH 090/584] ARM: dts: qcom: sdx55: Add reserved memory nodes This adds reserved memory nodes to the SDX55 dtsi as defined by v6 of the memory map Signed-off-by: Vinod Koul [mani: moved modem regions to board dts] Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-3-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 21 +++++++++++ arch/arm/boot/dts/qcom-sdx55.dtsi | 52 ++++++++++++++++++++++++++++ 2 files changed, 73 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 262660e6dd11..a5d2e4a3a796 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -20,6 +20,27 @@ chosen { stdout-path = "serial0:115200n8"; }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + mpss_debug_mem: memory@8ef00000 { + no-map; + reg = <0x8ef00000 0x800000>; + }; + + ipa_fw_mem: memory@8fced000 { + no-map; + reg = <0x8fced000 0x10000>; + }; + + mpss_adsp_mem: memory@90c00000 { + no-map; + reg = <0x90c00000 0xd400000>; + }; + }; }; &blsp1_uart3 { diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 913e558ae433..3698c2f29481 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -53,6 +53,58 @@ method = "smc"; }; + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + hyp_mem: memory@8fc00000 { + no-map; + reg = <0x8fc00000 0x80000>; + }; + + ac_db_mem: memory@8fc80000 { + no-map; + reg = <0x8fc80000 0x40000>; + }; + + secdata_mem: memory@8fcfd000 { + no-map; + reg = <0x8fcfd000 0x1000>; + }; + + sbl_mem: memory@8fd00000 { + no-map; + reg = <0x8fd00000 0x100000>; + }; + + aop_image: memory@8fe00000 { + no-map; + reg = <0x8fe00000 0x20000>; + }; + + aop_cmd_db: memory@8fe20000 { + compatible = "qcom,cmd-db"; + reg = <0x8fe20000 0x20000>; + no-map; + }; + + smem_mem: memory@8fe40000 { + no-map; + reg = <0x8fe40000 0xc0000>; + }; + + tz_mem: memory@8ff00000 { + no-map; + reg = <0x8ff00000 0x100000>; + }; + + tz_apps_mem: memory@0x90000000 { + no-map; + reg = <0x90000000 0x500000>; + }; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; From 752b0aac99c7e0b179875cdfa102d378ccb794a2 Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sun, 6 Dec 2020 17:51:27 +0100 Subject: [PATCH 091/584] dt-bindings: irq: sun7i-nmi: Add binding documentation for the V3s NMI The V3s NMI controller seems register-compatible with the A80 (sun9i). Add new items for the compatible string, with an entry specific to the V3s and the A80 entry. Acked-by: Rob Herring Signed-off-by: Paul Kocialkowski Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201206165131.1041983-2-contact@paulk.fr --- .../interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml index 8acca0ae3129..4fd1e2780026 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml +++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml @@ -29,6 +29,9 @@ properties: - items: - const: allwinner,sun8i-a83t-r-intc - const: allwinner,sun6i-a31-r-intc + - items: + - const: allwinner,sun8i-v3s-nmi + - const: allwinner,sun9i-a80-nmi - const: allwinner,sun9i-a80-nmi - items: - const: allwinner,sun50i-a64-r-intc From c20e9e7675137d92bca071305e79fcc10364ebf5 Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sun, 6 Dec 2020 17:51:28 +0100 Subject: [PATCH 092/584] ARM: dts: sun8i-v3s: Add the V3s NMI IRQ controller The V3s/V3 has a NMI interrupt controller, mainly used for the AXP209. Its address follows the system controller block, which was previously incorrectly described as spanning over 0x1000 address bytes. Even though this is what the Allwinner documentation indicates, precedence from other SoCs such as the R40 suggests that this is not actually the case. This reduces the system controller address span up to the NMI controller and adds a node for the controller, with its dedicated compatible. While the interrupt number was found in Allwinner's documentation, the address for the controller is specified in any Allwinner SDK supporting sun8iw8 (V3/V3s) at: drivers/power/axp_power/axp20/axp20-board.c It was tested to work on a V3 board with an AXP209 connected to the NMI interrupt line. Signed-off-by: Paul Kocialkowski Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201206165131.1041983-3-contact@paulk.fr --- arch/arm/boot/dts/sun8i-v3s.dtsi | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index f8f19d8fa795..b7b0e685e26b 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -157,12 +157,21 @@ syscon: system-control@1c00000 { compatible = "allwinner,sun8i-v3s-system-control", "allwinner,sun8i-h3-system-control"; - reg = <0x01c00000 0x1000>; + reg = <0x01c00000 0xd0>; #address-cells = <1>; #size-cells = <1>; ranges; }; + nmi_intc: interrupt-controller@1c000d0 { + compatible = "allwinner,sun8i-v3s-nmi", + "allwinner,sun9i-a80-nmi"; + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x01c000d0 0x0c>; + interrupts = ; + }; + tcon0: lcd-controller@1c0c000 { compatible = "allwinner,sun8i-v3s-tcon"; reg = <0x01c0c000 0x1000>; From 8c361a10d586bd07e7f34e678daab06fbcd05f87 Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sun, 6 Dec 2020 17:51:29 +0100 Subject: [PATCH 093/584] ARM: dts: sun8i: Cleanup the Pinecube AXP209 node This fixes a few things with the Pinecube AXP209 node: - No compatible is required since it is using an AXP209 (not AXP203) according to the schematics and this is what the included axp209.dtsi already has; - The interrupt-controller and #interrupt-cells properties are already described in the included axp209.dtsi; - The interrupt comes through the NMI controller, not directly through the GIC. Signed-off-by: Paul Kocialkowski Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201206165131.1041983-4-contact@paulk.fr --- arch/arm/boot/dts/sun8i-s3-pinecube.dts | 8 ++------ 1 file changed, 2 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-s3-pinecube.dts b/arch/arm/boot/dts/sun8i-s3-pinecube.dts index 4aa0ee897a0a..3c4bc4b0ca7f 100644 --- a/arch/arm/boot/dts/sun8i-s3-pinecube.dts +++ b/arch/arm/boot/dts/sun8i-s3-pinecube.dts @@ -88,13 +88,9 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp203", - "x-powers,axp209"; reg = <0x34>; - interrupt-parent = <&gic>; - interrupts = ; - interrupt-controller; - #interrupt-cells = <1>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; }; From 46ad18e7d0e294bc2a225e40ad98fa27eb20b86d Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sun, 6 Dec 2020 17:51:30 +0100 Subject: [PATCH 094/584] dt-bindings: arm: sunxi: Add SL631 with IMX179 bindings This adds documentation for the compatible strings of the SL631 Action Camera with IMX179. Note that the device is sold under various different names, such as the SJCAM SJ4000 Air or F60 Action Camera. This is a similar situation to the Q8 tablets and just like them, the allwinner vendor is used as fallback. Signed-off-by: Paul Kocialkowski Signed-off-by: Maxime Ripard Reviewed-by: Rob Herring Link: https://lore.kernel.org/r/20201206165131.1041983-5-contact@paulk.fr --- Documentation/devicetree/bindings/arm/sunxi.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 6db32fbf813f..85324cebb75d 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -777,6 +777,12 @@ properties: - const: sinlinx,sina33 - const: allwinner,sun8i-a33 + - description: SL631 Action Camera with IMX179 + items: + - const: allwinner,sl631-imx179 + - const: allwinner,sl631 + - const: allwinner,sun8i-v3 + - description: Tanix TX6 items: - const: oranth,tanix-tx6 From 8f39fab53a2537d6d797034013c2de9c5c1b7938 Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Sun, 6 Dec 2020 17:51:31 +0100 Subject: [PATCH 095/584] ARM: dts: sun8i-v3: Add support for the SL631 Action Camera with IMX179 The SL631 is a family of Allwinner V3 action cameras sold under various names, such as SJCAM SJ4000 Air or F60 Action Camera. Devices in this family share a common board design but can be found with different image sensors, including the IMX179 and the OV4689. This adds support for a common dtsi for the SL631 family as well as a specific dts for the IMX179 fashion, which will later be populated with an IMX179 node when a driver is available. Features that were tested on the device include: - UART debug - MMC - USB peripheral (e.g. g_ether) - Buttons - SPI NOR flash Note that the exact designer/vendor of these boards is unknown. Signed-off-by: Paul Kocialkowski Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201206165131.1041983-6-contact@paulk.fr --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts | 12 ++ arch/arm/boot/dts/sun8i-v3-sl631.dtsi | 138 ++++++++++++++++++++ 3 files changed, 151 insertions(+) create mode 100644 arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts create mode 100644 arch/arm/boot/dts/sun8i-v3-sl631.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..efe6c6d789f8 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1224,6 +1224,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \ sun8i-s3-lichee-zero-plus.dtb \ sun8i-s3-pinecube.dtb \ sun8i-t3-cqa3t-bv3.dtb \ + sun8i-v3-sl631-imx179.dtb \ sun8i-v3s-licheepi-zero.dtb \ sun8i-v3s-licheepi-zero-dock.dtb \ sun8i-v40-bananapi-m2-berry.dtb diff --git a/arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts b/arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts new file mode 100644 index 000000000000..117aeece4e55 --- /dev/null +++ b/arch/arm/boot/dts/sun8i-v3-sl631-imx179.dts @@ -0,0 +1,12 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR X11) +/* + * Copyright 2020 Paul Kocialkowski + */ + +#include "sun8i-v3-sl631.dtsi" + +/ { + model = "SL631 Action Camera with IMX179"; + compatible = "allwinner,sl631-imx179", "allwinner,sl631", + "allwinner,sun8i-v3"; +}; diff --git a/arch/arm/boot/dts/sun8i-v3-sl631.dtsi b/arch/arm/boot/dts/sun8i-v3-sl631.dtsi new file mode 100644 index 000000000000..e0d2a31efc7f --- /dev/null +++ b/arch/arm/boot/dts/sun8i-v3-sl631.dtsi @@ -0,0 +1,138 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR X11) +/* + * Copyright 2020 Paul Kocialkowski + */ + +/dts-v1/; + +#include "sun8i-v3.dtsi" + +#include +#include + +/ { + model = "SL631 Action Camera"; + compatible = "allwinner,sl631", "allwinner,sun8i-v3"; + + aliases { + serial0 = &uart1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&i2c0 { + status = "okay"; + + axp209: pmic@34 { + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pb_pins>; + status = "okay"; +}; + +&lradc { + vref-supply = <®_ldo2>; + status = "okay"; + + button-174 { + label = "Down"; + linux,code = ; + channel = <0>; + voltage = <174603>; + }; + + button-384 { + label = "Up"; + linux,code = ; + channel = <0>; + voltage = <384126>; + }; + + button-593 { + label = "OK"; + linux,code = ; + channel = <0>; + voltage = <593650>; + }; +}; + +&mmc0 { + cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ + bus-width = <4>; + vmmc-supply = <®_dcdc3>; + status = "okay"; +}; + +&pio { + vcc-pd-supply = <®_dcdc3>; + vcc-pe-supply = <®_dcdc3>; +}; + +#include "axp209.dtsi" + +&ac_power_supply { + status = "okay"; +}; + +&battery_power_supply { + status = "okay"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-name = "vdd-sys-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vdd-3v3"; +}; + +®_ldo1 { + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +&spi0 { + status = "okay"; + + spi-flash@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + }; +}; + +&uart1 { + pinctrl-0 = <&uart1_pg_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usb_otg { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; From 8315c99cc7cb6346ed0083a262b28d29765f082f Mon Sep 17 00:00:00 2001 From: Michael Klein Date: Fri, 11 Dec 2020 16:14:45 +0100 Subject: [PATCH 096/584] ARM: dts: sun8i-h2-plus-bananapi-m2-zero: add poweroff node Add add devicetree information for the regulator-poweroff driver. Signed-off-by: Michael Klein Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201211151445.115943-4-michael@fossekall.de --- arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts index b43028f9e6df..f8a7b1371e97 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -86,6 +86,11 @@ vin-supply = <®_vcc5v0>; }; + poweroff { + compatible = "regulator-poweroff"; + cpu-supply = <®_vcc1v2>; + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ From 3c3f87d71181f7bde8c2998dd48cb3d861f391c0 Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 24 Dec 2020 10:39:59 +0800 Subject: [PATCH 097/584] dt-bindings: arm: sunxi: add PineTab Early Adopter edition Early adopter's PineTabs (and further releases) will have a new LCD panel different with the one that is used when in development (because the old panel's supply discontinued). Add a new DT compatible for it. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201224024001.19248-1-icenowy@aosc.io --- Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 85324cebb75d..8ab0d79dd44e 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -700,6 +700,11 @@ properties: - const: pine64,pinetab - const: allwinner,sun50i-a64 + - description: Pine64 PineTab, Early Adopter's batch (and maybe later ones) + items: + - const: pine64,pinetab-early-adopter + - const: allwinner,sun50i-a64 + - description: Pine64 SoPine Baseboard items: - const: pine64,sopine-baseboard From 7fa40ca7ef61926009f05df38802fe1fb6f0a20a Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 24 Dec 2020 10:40:00 +0800 Subject: [PATCH 098/584] arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab PineTabs since Early Adopter batch will use a new LCD panel. Add device tree for PineTab with the new panel. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201224024001.19248-2-icenowy@aosc.io --- arch/arm64/boot/dts/allwinner/Makefile | 1 + .../sun50i-a64-pinetab-early-adopter.dts | 26 +++++++++++++++++++ 2 files changed, 27 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index 211d1e9d4701..41ce680e5f8d 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.0.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinephone-1.2.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pinetab-early-adopter.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts new file mode 100644 index 000000000000..652fc0cce304 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts @@ -0,0 +1,26 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2020 Icenowy Zheng + * + */ + +/dts-v1/; + +#include "sun50i-a64-pinetab.dts" + +/ { + model = "PineTab, Early Adopter's version"; + compatible = "pine64,pinetab-early-adopter", "allwinner,sun50i-a64"; +}; + +&dsi { + /delete-node/ panel@0; + + panel@0 { + compatible = "feixin,k101-im2byl02"; + reg = <0>; + power-supply = <®_dc1sw>; + reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ + backlight = <&backlight>; + }; +}; From bdb574e592bcf5f7fe17d0173464327fc08ded5b Mon Sep 17 00:00:00 2001 From: Icenowy Zheng Date: Thu, 24 Dec 2020 10:41:38 +0800 Subject: [PATCH 099/584] dt-bindings: arm: sunxi: document orig PineTab DT as sample As the original PineTab DT (which uses sun50i-a64-pinetab name) is only for development samples, document this. Signed-off-by: Icenowy Zheng Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201224024138.19422-1-icenowy@aosc.io --- Documentation/devicetree/bindings/arm/sunxi.yaml | 2 +- arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 8ab0d79dd44e..42a4d01077f0 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -695,7 +695,7 @@ properties: - const: pine64,pinephone-1.2 - const: allwinner,sun50i-a64 - - description: Pine64 PineTab + - description: Pine64 PineTab, Development Sample items: - const: pine64,pinetab - const: allwinner,sun50i-a64 diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts index 0494bfaf2ffa..422a8507f674 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts @@ -14,7 +14,7 @@ #include / { - model = "PineTab"; + model = "PineTab, Development Sample"; compatible = "pine64,pinetab", "allwinner,sun50i-a64"; aliases { From 536f74a892e6a034e09a0d204dd2a3b3b02c5b30 Mon Sep 17 00:00:00 2001 From: Dylan Van Assche Date: Wed, 30 Dec 2020 11:42:05 +0100 Subject: [PATCH 100/584] arm64: allwinner: dts: pinephone: add 'pine64, pinephone' to the compatible list All revisions of the PinePhone share most of the hardware. This patch makes it easier to detect PinePhone hardware without having to check for each possible revision. Signed-off-by: Dylan Van Assche Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20201230104205.5592-1-me@dylanvanassche.be --- Documentation/devicetree/bindings/arm/sunxi.yaml | 3 +++ arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts | 2 +- arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts | 2 +- arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts | 2 +- 4 files changed, 6 insertions(+), 3 deletions(-) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 42a4d01077f0..7ea4d9645e93 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -683,16 +683,19 @@ properties: - description: Pine64 PinePhone Developer Batch (1.0) items: - const: pine64,pinephone-1.0 + - const: pine64,pinephone - const: allwinner,sun50i-a64 - description: Pine64 PinePhone Braveheart (1.1) items: - const: pine64,pinephone-1.1 + - const: pine64,pinephone - const: allwinner,sun50i-a64 - description: Pine64 PinePhone (1.2) items: - const: pine64,pinephone-1.2 + - const: pine64,pinephone - const: allwinner,sun50i-a64 - description: Pine64 PineTab, Development Sample diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts index 3d5a2ae9aa39..fb65319a3bd3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts @@ -7,7 +7,7 @@ / { model = "Pine64 PinePhone Developer Batch (1.0)"; - compatible = "pine64,pinephone-1.0", "allwinner,sun50i-a64"; + compatible = "pine64,pinephone-1.0", "pine64,pinephone", "allwinner,sun50i-a64"; }; &sgm3140 { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts index c9b9f6e9ee8c..5e59d3752178 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts @@ -7,7 +7,7 @@ / { model = "Pine64 PinePhone Braveheart (1.1)"; - compatible = "pine64,pinephone-1.1", "allwinner,sun50i-a64"; + compatible = "pine64,pinephone-1.1", "pine64,pinephone", "allwinner,sun50i-a64"; }; &backlight { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts index acc0ab53b9c1..4e7e237cb46a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.2.dts @@ -7,7 +7,7 @@ / { model = "Pine64 PinePhone (1.2)"; - compatible = "pine64,pinephone-1.2", "allwinner,sun50i-a64"; + compatible = "pine64,pinephone-1.2", "pine64,pinephone", "allwinner,sun50i-a64"; wifi_pwrseq: wifi-pwrseq { compatible = "mmc-pwrseq-simple"; From f036549f29a32fbd29a545b1aa568fcd065d88ab Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:08 +0530 Subject: [PATCH 101/584] ARM: dts: qcom: sdx55: Add support for SDHCI controller Add devicetree support for SDHCI controller found in Qualcomm SDX55 platform. The SDHCI controller is based on the MSM SDHCI v5 IP. Hence, the support is added by reusing the existing sdhci driver with "qcom,sdhci-msm-v5" as the fallback. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-5-manivannan.sadhasivam@linaro.org [bjorn: added include of qcom,gcc-sdx55.h] Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 3698c2f29481..781a4ec83d47 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -6,6 +6,7 @@ * Copyright (c) 2020, Linaro Ltd. */ +#include #include #include #include @@ -130,6 +131,18 @@ status = "disabled"; }; + sdhc_1: sdhci@8804000 { + compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x08804000 0x1000>; + interrupts = , + ; + interrupt-names = "hc_irq", "pwr_irq"; + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>; + clock-names = "iface", "core"; + status = "disabled"; + }; + pdc: interrupt-controller@b210000 { compatible = "qcom,sdx55-pdc", "qcom,pdc"; reg = <0x0b210000 0x30000>; From a2bdfdfba2afb532f2a2c8082bdb7de8379a4b6c Mon Sep 17 00:00:00 2001 From: Bjorn Andersson Date: Wed, 6 Jan 2021 18:23:10 +0530 Subject: [PATCH 102/584] ARM: dts: qcom: sdx55: Enable ARM SMMU Add a node for the ARM SMMU found in the SDX55. Signed-off-by: Bjorn Andersson Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-7-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 781a4ec83d47..9e25ad8dcbce 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -162,6 +162,30 @@ #interrupt-cells = <2>; }; + apps_smmu: iommu@15000000 { + compatible = "qcom,sdx55-smmu-500", "arm,mmu-500"; + reg = <0x15000000 0x20000>; + #iommu-cells = <2>; + #global-interrupts = <1>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + }; + intc: interrupt-controller@17800000 { compatible = "qcom,msm-qgic2"; interrupt-controller; From 985eef1d034319267cc766d1e91d2d92847c428a Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:11 +0530 Subject: [PATCH 103/584] ARM: dts: qcom: sdx55: Add support for TCSR Mutex Add TCSR Mutex node to support Qualcomm Hardware Mutex block on SDX55 platform. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-8-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 9e25ad8dcbce..21308e87cae6 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -131,6 +131,12 @@ status = "disabled"; }; + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x01f40000 0x40000>; + #hwlock-cells = <1>; + }; + sdhc_1: sdhci@8804000 { compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5"; reg = <0x08804000 0x1000>; From 8cf74d0565cf96cb6b154b6c49244ec47db1af5e Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:12 +0530 Subject: [PATCH 104/584] ARM: dts: qcom: sdx55: Add Shared memory manager support Add smem node to support shared memory manager on SDX55 platform. Signed-off-by: Manivannan Sadhasivam Reviewed-by: Vinod Koul Link: https://lore.kernel.org/r/20210106125322.61840-9-manivannan.sadhasivam@linaro.org [bjorn: Moved smem node out from /soc] Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 21308e87cae6..87a62e018446 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -106,6 +106,12 @@ }; }; + smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; From 2470941806c66acad99b71f3fc8793066c6792f8 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:13 +0530 Subject: [PATCH 105/584] ARM: dts: qcom: sdx55: Add QPIC BAM support Add qpic_bam node to support QPIC BAM DMA controller on SDX55 platform. Signed-off-by: Manivannan Sadhasivam Reviewed-by: Vinod Koul Link: https://lore.kernel.org/r/20210106125322.61840-10-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 87a62e018446..36b066a51242 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -137,6 +137,18 @@ status = "disabled"; }; + qpic_bam: dma-controller@1b04000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x01b04000 0x1c000>; + interrupts = ; + clocks = <&rpmhcc RPMH_QPIC_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + qcom,controlled-remotely; + status = "disabled"; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x01f40000 0x40000>; From 4bd7bfb4566a9464a1933d0d2aa2df0f03c20e8b Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:14 +0530 Subject: [PATCH 106/584] ARM: dts: qcom: sdx55: Add QPIC NAND support Add qpic_nand node to support QPIC NAND controller on SDX55 platform. Since there is no "aon" clock in SDX55, a dummy clock is provided. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-11-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 36b066a51242..51c67d17387f 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -35,6 +35,12 @@ #clock-cells = <0>; clock-frequency = <32000>; }; + + nand_clk_dummy: nand-clk-dummy { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32000>; + }; }; cpus { @@ -149,6 +155,22 @@ status = "disabled"; }; + qpic_nand: nand@1b30000 { + compatible = "qcom,sdx55-nand"; + reg = <0x01b30000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&rpmhcc RPMH_QPIC_CLK>, + <&nand_clk_dummy>; + clock-names = "core", "aon"; + + dmas = <&qpic_bam 0>, + <&qpic_bam 1>, + <&qpic_bam 2>; + dma-names = "tx", "rx", "cmd"; + status = "disabled"; + }; + tcsr_mutex: hwlock@1f40000 { compatible = "qcom,tcsr-mutex"; reg = <0x01f40000 0x40000>; From 512e39d2cf095e9d991eb106136134dcd50e4e01 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:15 +0530 Subject: [PATCH 107/584] ARM: dts: qcom: sdx55-mtp: Enable BAM DMA Enable BAM DMA on SDX55-MTP board. Signed-off-by: Manivannan Sadhasivam Reviewed-by: Vinod Koul Link: https://lore.kernel.org/r/20210106125322.61840-12-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index a5d2e4a3a796..177886e168aa 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -46,3 +46,7 @@ &blsp1_uart3 { status = "ok"; }; + +&qpic_bam { + status = "ok"; +}; From 4f944be5f567024955bfa2839eed69a7761f454e Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Wed, 6 Jan 2021 18:23:16 +0530 Subject: [PATCH 108/584] ARM: dts: qcom: sdx55-mtp: Enable QPIC NAND Enable QPIC NAND on SDX55-MTP board. Signed-off-by: Manivannan Sadhasivam Reviewed-by: Vinod Koul Link: https://lore.kernel.org/r/20210106125322.61840-13-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 177886e168aa..83b9d784423e 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -50,3 +50,15 @@ &qpic_bam { status = "ok"; }; + +&qpic_nand { + status = "ok"; + + nand@0 { + reg = <0>; + + nand-ecc-strength = <8>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + }; +}; From 3b6785ed437ed6fd57ad12e006e30f7baabc5fce Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:17 +0530 Subject: [PATCH 109/584] ARM: dts: qcom: sdx55: Add spmi node This adds SPMI node to SDX55 dts. Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-14-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 51c67d17387f..57f0512efafa 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -198,6 +198,25 @@ interrupt-controller; }; + spmi_bus: qcom,spmi@c440000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0c440000 0x0000d00>, + <0x0c600000 0x2000000>, + <0x0e600000 0x0100000>, + <0x0e700000 0x00a0000>, + <0x0c40a000 0x0000700>; + reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; + interrupt-names = "periph_irq"; + interrupts = ; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + cell-index = <0>; + }; + tlmm: pinctrl@f100000 { compatible = "qcom,sdx55-pinctrl"; reg = <0xf100000 0x300000>; From e6facb6331f94c93011733d5a35cbe320713d360 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:18 +0530 Subject: [PATCH 110/584] ARM: dts: qcom: sdx55-mtp: Add pm8150b pmic SDX55-mtp features PM8150B pmic, so include the dts as well Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-15-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 83b9d784423e..6ec0c3f1f275 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -7,6 +7,7 @@ /dts-v1/; #include "qcom-sdx55.dtsi" +#include / { model = "Qualcomm Technologies, Inc. SDX55 MTP"; From 3cef2d55f9eec31626c5a27602e93ddf71cc7672 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:20 +0530 Subject: [PATCH 111/584] ARM: dts: qcom: sdx55: Add rpmpd node This adds rpmpd node and opps for this node to the SDX55 dts. Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-17-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 51 +++++++++++++++++++++++++++++++ 1 file changed, 51 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 57f0512efafa..4838ba03c62e 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -9,6 +9,7 @@ #include #include #include +#include #include / { @@ -343,6 +344,56 @@ clock-names = "xo"; clocks = <&xo_board>; }; + + rpmhpd: power-controller { + compatible = "qcom,sdx55-rpmhpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmhpd_opp_table>; + + rpmhpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmhpd_opp_ret: opp1 { + opp-level = ; + }; + + rpmhpd_opp_min_svs: opp2 { + opp-level = ; + }; + + rpmhpd_opp_low_svs: opp3 { + opp-level = ; + }; + + rpmhpd_opp_svs: opp4 { + opp-level = ; + }; + + rpmhpd_opp_svs_l1: opp5 { + opp-level = ; + }; + + rpmhpd_opp_nom: opp6 { + opp-level = ; + }; + + rpmhpd_opp_nom_l1: opp7 { + opp-level = ; + }; + + rpmhpd_opp_nom_l2: opp8 { + opp-level = ; + }; + + rpmhpd_opp_turbo: opp9 { + opp-level = ; + }; + + rpmhpd_opp_turbo_l1: opp10 { + opp-level = ; + }; + }; + }; }; }; From c222f3ec120f8fb40fe504e20640db5d863b1b72 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:21 +0530 Subject: [PATCH 112/584] ARM: dts: qcom: Add PMIC pmx55 dts This adds DTS for PMIC PMX55 found in Qualcomm platforms. Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-18-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-pmx55.dtsi | 84 +++++++++++++++++++++++++++++++ 1 file changed, 84 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-pmx55.dtsi diff --git a/arch/arm/boot/dts/qcom-pmx55.dtsi b/arch/arm/boot/dts/qcom-pmx55.dtsi new file mode 100644 index 000000000000..6571b88d018a --- /dev/null +++ b/arch/arm/boot/dts/qcom-pmx55.dtsi @@ -0,0 +1,84 @@ +// SPDX-License-Identifier: BSD-3-Clause + +/* + * Copyright (c) 2018-2020, The Linux Foundation. All rights reserved. + * Copyright (c) 2020, Linaro Limited + */ + +#include +#include +#include + +&spmi_bus { + pmic@8 { + compatible = "qcom,pmx55", "qcom,spmi-pmic"; + reg = <0x8 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + power-on@800 { + compatible = "qcom,pm8916-pon"; + reg = <0x0800>; + + status = "disabled"; + }; + + pmx55_temp: temp-alarm@2400 { + compatible = "qcom,spmi-temp-alarm"; + reg = <0x2400>; + interrupts = <0x8 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; + io-channels = <&pmx55_adc ADC5_DIE_TEMP>; + io-channel-names = "thermal"; + #thermal-sensor-cells = <0>; + }; + + pmx55_adc: adc@3100 { + compatible = "qcom,spmi-adc5"; + reg = <0x3100>; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + interrupts = <0x8 0x31 0x0 IRQ_TYPE_EDGE_RISING>; + + ref-gnd@0 { + reg = ; + qcom,pre-scaling = <1 1>; + label = "ref_gnd"; + }; + + vref-1p25@1 { + reg = ; + qcom,pre-scaling = <1 1>; + label = "vref_1p25"; + }; + + die-temp@6 { + reg = ; + qcom,pre-scaling = <1 1>; + label = "die_temp"; + }; + + chg-temp@9 { + reg = ; + qcom,pre-scaling = <1 1>; + label = "chg_temp"; + }; + }; + + pmx55_gpios: gpio@c000 { + compatible = "qcom,pmx55-gpio", "qcom,spmi-gpio"; + reg = <0xc000>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + pmic@9 { + compatible = "qcom,pmx55", "qcom,spmi-pmic"; + reg = <0x9 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + }; +}; From 8bf259a9c7f9d8870e65a4ac74f2693ee8add0e2 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:19 +0530 Subject: [PATCH 113/584] ARM: dts: qcom: sdx55-mtp: Add pmx55 pmic SDX55-mtp features PMX55 pmic, so include the dts as well Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-16-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 6ec0c3f1f275..5b247f628d18 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -8,6 +8,7 @@ #include "qcom-sdx55.dtsi" #include +#include "qcom-pmx55.dtsi" / { model = "Qualcomm Technologies, Inc. SDX55 MTP"; From d949eaf870892d2cfa6f37f95919484dd769940b Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 6 Jan 2021 18:23:22 +0530 Subject: [PATCH 114/584] ARM: dts: qcom: sdx55-mtp: Add regulator nodes This adds the regulators found on SDX55 MTP. Signed-off-by: Vinod Koul Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210106125322.61840-19-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 164 +++++++++++++++++++++++++++ 1 file changed, 164 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 5b247f628d18..96b6a295f813 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -7,6 +7,7 @@ /dts-v1/; #include "qcom-sdx55.dtsi" +#include #include #include "qcom-pmx55.dtsi" @@ -43,6 +44,169 @@ reg = <0x90c00000 0xd400000>; }; }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + vreg_bob_3p3: pmx55-bob { + compatible = "regulator-fixed"; + regulator-name = "vreg_bob_3p3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + vreg_s7e_mx_0p752: pmx55-s7e { + compatible = "regulator-fixed"; + regulator-name = "vreg_s7e_mx_0p752"; + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <752000>; + + vin-supply = <&vph_pwr>; + }; +}; + +&apps_rsc { + pmx55-rpmh-regulators { + compatible = "qcom,pmx55-rpmh-regulators"; + qcom,pmic-id = "e"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-l1-l2-supply = <&vreg_s2e_1p224>; + vdd-l3-l9-supply = <&vreg_s3e_0p824>; + vdd-l4-l12-supply = <&vreg_s4e_1p904>; + vdd-l5-l6-supply = <&vreg_s4e_1p904>; + vdd-l7-l8-supply = <&vreg_s3e_0p824>; + vdd-l10-l11-l13-supply = <&vreg_bob_3p3>; + vdd-l14-supply = <&vreg_s7e_mx_0p752>; + vdd-l15-supply = <&vreg_s2e_1p224>; + vdd-l16-supply = <&vreg_s4e_1p904>; + + vreg_s2e_1p224: smps2 { + regulator-min-microvolt = <1280000>; + regulator-max-microvolt = <1400000>; + }; + + vreg_s3e_0p824: smps3 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_s4e_1p904: smps4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1960000>; + }; + + ldo1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + + ldo2 { + regulator-min-microvolt = <1128000>; + regulator-max-microvolt = <1128000>; + regulator-initial-mode = ; + }; + + ldo3 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = ; + }; + + ldo4 { + regulator-min-microvolt = <872000>; + regulator-max-microvolt = <872000>; + regulator-initial-mode = ; + }; + + ldo5 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = ; + }; + + ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + ldo7 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <900000>; + regulator-initial-mode = ; + }; + + ldo8 { + regulator-min-microvolt = <480000>; + regulator-max-microvolt = <900000>; + regulator-initial-mode = ; + }; + + ldo9 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = ; + }; + + ldo10 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = ; + }; + + ldo11 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = ; + }; + + ldo12 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + + ldo13 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <2928000>; + regulator-initial-mode = ; + }; + + ldo14 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = ; + }; + + ldo15 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + + ldo16 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <1904000>; + regulator-initial-mode = ; + }; + }; }; &blsp1_uart3 { From 26442c799857d7b776085dde37fa93fc2fd21bd1 Mon Sep 17 00:00:00 2001 From: Shengjiu Wang Date: Mon, 7 Dec 2020 17:12:34 +0800 Subject: [PATCH 115/584] arm64: dts: imx8mn: Configure clock rate for audio plls Configure clock rate for audio plls. audio pll1 is used as parent clock for clocks that is multiple of 8kHz. audio pll2 is used as parent clock for clocks that is multiple of 11kHz. Signed-off-by: Shengjiu Wang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mn.dtsi | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index ee1790230490..00808bb40680 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -581,7 +581,9 @@ <&clk IMX8MN_CLK_NOC>, <&clk IMX8MN_CLK_AUDIO_AHB>, <&clk IMX8MN_CLK_IPG_AUDIO_ROOT>, - <&clk IMX8MN_SYS_PLL3>; + <&clk IMX8MN_SYS_PLL3>, + <&clk IMX8MN_AUDIO_PLL1>, + <&clk IMX8MN_AUDIO_PLL2>; assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_800M>, <&clk IMX8MN_ARM_PLL_OUT>, <&clk IMX8MN_SYS_PLL3_OUT>, @@ -589,7 +591,9 @@ assigned-clock-rates = <0>, <0>, <0>, <400000000>, <400000000>, - <600000000>; + <600000000>, + <393216000>, + <361267200>; }; src: reset-controller@30390000 { From b5f2ace2283ce35df006d1f13ee9ea9dae3ba924 Mon Sep 17 00:00:00 2001 From: Shengjiu Wang Date: Mon, 7 Dec 2020 17:12:35 +0800 Subject: [PATCH 116/584] arm64: dts: imx8mn-evk: Add sound-wm8524 card nodes Add sound-wm8524 card nodes which are supported on imx8mn-evk board. Signed-off-by: Shengjiu Wang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 51 +++++++++++++++++++ 1 file changed, 51 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi index 76d042a4cf09..1d2c399eabea 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi @@ -46,6 +46,32 @@ pinctrl-0 = <&pinctrl_ir>; linux,autosuspend-period = <125>; }; + + wm8524: audio-codec { + #sound-dai-cells = <0>; + compatible = "wlf,wm8524"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_wlf>; + wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + clocks = <&clk IMX8MN_CLK_SAI3_ROOT>; + clock-names = "mclk"; + }; + + sound-wm8524 { + compatible = "fsl,imx-audio-wm8524"; + model = "wm8524-audio"; + audio-cpu = <&sai3>; + audio-codec = <&wm8524>; + audio-asrc = <&easrc>; + audio-routing = + "Line Out Jack", "LINEVOUTL", + "Line Out Jack", "LINEVOUTR"; + }; +}; + +&easrc { + fsl,asrc-rate = <48000>; + status = "okay"; }; &fec1 { @@ -124,6 +150,16 @@ }; }; +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MN_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + fsl,sai-mclk-direction-output; + status = "okay"; +}; + &snvs_pwrkey { status = "okay"; }; @@ -210,6 +246,12 @@ >; }; + pinctrl_gpio_wlf: gpiowlfgrp { + fsl,pins = < + MX8MN_IOMUXC_I2C4_SDA_GPIO5_IO21 0xd6 + >; + }; + pinctrl_ir: irgrp { fsl,pins = < MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13 0x4f @@ -249,6 +291,15 @@ >; }; + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + >; + }; + pinctrl_typec1: typec1grp { fsl,pins = < MX8MN_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 From 4c36eb101986f0719bf10ba14c44346ed85c3806 Mon Sep 17 00:00:00 2001 From: Shengjiu Wang Date: Mon, 7 Dec 2020 17:12:36 +0800 Subject: [PATCH 117/584] arm64: dts: imx8mn-evk: Add sound-spdif card nodes Add sound-spdif card nodes which are supported on imx8mn-evk board. Signed-off-by: Shengjiu Wang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 24 +++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi index 1d2c399eabea..a0dddba2e561 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi @@ -67,6 +67,14 @@ "Line Out Jack", "LINEVOUTL", "Line Out Jack", "LINEVOUTR"; }; + + sound-spdif { + compatible = "fsl,imx-audio-spdif"; + model = "imx-spdif"; + spdif-controller = <&spdif1>; + spdif-out; + spdif-in; + }; }; &easrc { @@ -164,6 +172,15 @@ status = "okay"; }; +&spdif1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif1>; + assigned-clocks = <&clk IMX8MN_CLK_SPDIF1>; + assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + &uart2 { /* console */ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart2>; @@ -300,6 +317,13 @@ >; }; + pinctrl_spdif1: spdif1grp { + fsl,pins = < + MX8MN_IOMUXC_SPDIF_TX_SPDIF1_OUT 0xd6 + MX8MN_IOMUXC_SPDIF_RX_SPDIF1_IN 0xd6 + >; + }; + pinctrl_typec1: typec1grp { fsl,pins = < MX8MN_IOMUXC_SD1_STROBE_GPIO2_IO11 0x159 From d3c83bcab3186eba6eecc852b9858678fe9c2e6f Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:32 +0100 Subject: [PATCH 118/584] dt-bindings: display: simple: fix alphabetical order for EDT compatibles Reorder it alphabetically and remove one double entry. Signed-off-by: Oleksij Rempel Reviewed-by: Rob Herring Signed-off-by: Shawn Guo --- .../bindings/display/panel/panel-simple.yaml | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml index 27fffafe5b5c..5c4c61676dff 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml @@ -105,26 +105,24 @@ properties: - dlc,dlc1010gig # Emerging Display Technology Corp. 3.5" QVGA TFT LCD panel - edt,et035012dm6 + # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel + - edt,et057090dhu # Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch - edt,etm043080dh6gp # Emerging Display Technology Corp. 480x272 TFT Display - edt,etm0430g0dh6 - # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel - - edt,et057090dhu - # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch - - edt,etm070080dh6 - # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch - - edt,etm0700g0dh6 # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch # Same as ETM0700G0DH6 but with inverted pixel clock. - edt,etm070080bdh6 + # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch + # Same timings as the ETM0700G0DH6, but with resistive touch. + - edt,etm070080dh6 # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch # Same display as the ETM0700G0BDH6, but with changed hardware for the # backlight and the touch interface. - edt,etm070080edh6 # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch - # Same timings as the ETM0700G0DH6, but with resistive touch. - - edt,etm070080dh6 + - edt,etm0700g0dh6 # Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel - evervision,vgg804821 # Foxlink Group 5" WVGA TFT LCD panel From 279ebba7fbf0380c27f74b5d21d61639a8b65dd2 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:33 +0100 Subject: [PATCH 119/584] dt-bindings: display: simple: add EDT compatibles already supported by the driver Some EDT compatibles are already supported by the driver but will fail on checkpatch script. Fix it by syncing dt-bindings documentation with the driver. Signed-off-by: Oleksij Rempel Reviewed-by: Rob Herring Signed-off-by: Shawn Guo --- .../devicetree/bindings/display/panel/panel-simple.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml index 5c4c61676dff..cb52948188f1 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml @@ -107,6 +107,7 @@ properties: - edt,et035012dm6 # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel - edt,et057090dhu + - edt,et070080dh6 # Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch - edt,etm043080dh6gp # Emerging Display Technology Corp. 480x272 TFT Display @@ -121,8 +122,10 @@ properties: # Same display as the ETM0700G0BDH6, but with changed hardware for the # backlight and the touch interface. - edt,etm070080edh6 + - edt,etm0700g0bdh6 # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch - edt,etm0700g0dh6 + - edt,etm0700g0edh6 # Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel - evervision,vgg804821 # Foxlink Group 5" WVGA TFT LCD panel From 922fb2db02871671c49afeaa73166553edf5a00c Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:34 +0100 Subject: [PATCH 120/584] dt-bindings: display: simple: Add Kyocera tcg070wvlq panel So far, this panel seems to be compatible with "lg,lb070wv8", on other hand it is better to set this compatible in the devicetree. So, let's add it for now only to the dt-binding documentation to fix the checkpatch warnings. Signed-off-by: Oleksij Rempel Reviewed-by: Rob Herring Signed-off-by: Shawn Guo --- .../devicetree/bindings/display/panel/panel-simple.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml index cb52948188f1..3207608d1178 100644 --- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml +++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml @@ -174,6 +174,8 @@ properties: - koe,tx26d202vm0bwa # Kaohsiung Opto-Electronics. TX31D200VM0BAA 12.3" HSXGA LVDS panel - koe,tx31d200vm0baa + # Kyocera Corporation 7" WVGA (800x480) transmissive color TFT + - kyo,tcg070wvlq # Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel - kyo,tcg121xglp # LeMaker BL035-RGB-002 3.5" QVGA TFT LCD panel From 7ae786b05f7eae83dc61e60d32a3a013b1844f9a Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:35 +0100 Subject: [PATCH 121/584] dt-bindings: vendor-prefixes: Add an entry for Plymovent Add "ply" entry for Plymovent Group BV: https://www.plymovent.com/ Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 041ae90b0d8f..f03ba0c4ae5e 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -866,6 +866,8 @@ patternProperties: description: PLDA "^plx,.*": description: Broadcom Corporation (formerly PLX Technology) + "^ply,.*": + description: Plymovent Group BV "^pni,.*": description: PNI Sensor Corporation "^pocketbook,.*": From 94e17a03395314312f868c0695ca65e9ec719c6b Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:36 +0100 Subject: [PATCH 122/584] dt-bindings: arm: fsl: add Plymovent M2M board Add Plymovent Group BV M2M iMX6dl based board Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index cee74fc0c115..cd76a7933700 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -364,6 +364,7 @@ properties: - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules - kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module + - ply,plym2m # Plymovent M2M board - poslab,imx6dl-savageboard # Poslab SavageBoard Dual - prt,prtrvt # Protonic RVT board - prt,prtvt7 # Protonic VT7 board From f1b8d58d3188108fd4ce066886594dc27a6d09c9 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:38 +0100 Subject: [PATCH 123/584] dt-bindings: arm: fsl: add Plymovent BAS board Add Plymovent Group BV BAS iMX6dl based board Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index cd76a7933700..51b8d6fac792 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -364,6 +364,7 @@ properties: - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules - kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module + - ply,plybas # Plymovent BAS board - ply,plym2m # Plymovent M2M board - poslab,imx6dl-savageboard # Poslab SavageBoard Dual - prt,prtrvt # Protonic RVT board From 8c906de4b76881f580f40c9a4c4c33dcc9ed1fbb Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:37 +0100 Subject: [PATCH 124/584] ARM: dts: add Plymovent M2M board Plymovent M2M is a control interface produced for the Plymovent filter systems. Co-Developed-by: David Jander Signed-off-by: David Jander Signed-off-by: Oleksij Rempel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-plym2m.dts | 446 ++++++++++++++++++++++++++++ 2 files changed, 447 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-plym2m.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..6a6cc12cee8f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -465,6 +465,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-pico-hobbit.dtb \ imx6dl-pico-nymph.dtb \ imx6dl-pico-pi.dtb \ + imx6dl-plym2m.dtb \ imx6dl-prtrvt.dtb \ imx6dl-prtvt7.dtb \ imx6dl-rex-basic.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts new file mode 100644 index 000000000000..4d0d3d3386af --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-plym2m.dts @@ -0,0 +1,446 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2014 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel , Pengutronix + */ + +/dts-v1/; +#include +#include +#include "imx6dl.dtsi" + +/ { + model = "Plymovent M2M board"; + compatible = "ply,plym2m", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000 0>; + brightness-levels = <0 1000>; + num-interpolated-steps = <20>; + default-brightness-level = <19>; + power-supply = <®_12v0>; + }; + + display { + compatible = "fsl,imx-parallel-display"; + pinctrl-0 = <&pinctrl_ipu1_disp>; + pinctrl-names = "default"; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + display_in: endpoint { + remote-endpoint = <&ipu1_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "debug0"; + function = LED_FUNCTION_STATUS; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + panel { + compatible = "edt,etm0700g0bdh6"; + backlight = <&backlight>; + power-supply = <®_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + + clk50m_phy: phy-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v0: regulator-5v0 { + compatible = "regulator-fixed"; + regulator-name = "5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_12v0: regulator-12v0 { + compatible = "regulator-fixed"; + regulator-name = "12v0"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + xceiver-supply = <®_5v0>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + touchscreen@0 { + compatible = "ti,tsc2046"; + reg = <0>; + pinctrl-0 = <&pinctrl_tsc2046>; + pinctrl-names ="default"; + spi-max-frequency = <100000>; + interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>; + pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>; + + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-x; + touchscreen-inverted-y; + touchscreen-max-pressure = <4095>; + + ti,vref-delay-usecs = /bits/ 16 <100>; + ti,x-plate-ohms = /bits/ 16 <800>; + ti,y-plate-ohms = /bits/ 16 <300>; + + wakeup-source; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clk50m_phy>; + clock-names = "ipg", "ahb", "ptp"; + phy-handle = <&rgmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rgmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "CAN1_TERM", "SD1_CD", "", "", "", "", "", "", + "DEBUG_0", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "CAN1_SR", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "ETH_RESET", "ETH_INTRP", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&ipu1_di0_disp0 { + remote-endpoint = <&display_in>; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbphynop1 { + status = "disabled"; +}; + +&usbphynop2 { + status = "disabled"; +}; + +&usbotg { + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x10000 + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x3008 + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x3008 + /* CS */ + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x3008 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_disp: ipudisp1grp { + fsl,pins = < + /* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */ + MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x30 + MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x30 + MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x30 + MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x30 + MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x30 + MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x30 + MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x30 + MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x30 + MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x30 + MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x30 + MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x30 + MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x30 + MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x30 + MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x30 + MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x30 + MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x30 + MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x30 + MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x30 + MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x30 + MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x30 + MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x30 + MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x30 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8 + >; + }; + + pinctrl_tsc2046: tsc2046grp { + fsl,pins = < + /* TSC_PENIRQ */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1 + /* TSC_BUSY */ + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; +}; From 2c62f908c08e03c7c4425dc373ca77a28619e40e Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 7 Dec 2020 15:09:39 +0100 Subject: [PATCH 125/584] ARM: dts: add Plymovent BAS board Plymovent BAS is a base system controller produced for the Plymovent filter systems. Co-Developed-by: David Jander Signed-off-by: David Jander Signed-off-by: Oleksij Rempel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-plybas.dts | 394 ++++++++++++++++++++++++++++ 2 files changed, 395 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-plybas.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 6a6cc12cee8f..0756c41106fd 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -465,6 +465,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-pico-hobbit.dtb \ imx6dl-pico-nymph.dtb \ imx6dl-pico-pi.dtb \ + imx6dl-plybas.dtb \ imx6dl-plym2m.dtb \ imx6dl-prtrvt.dtb \ imx6dl-prtvt7.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts new file mode 100644 index 000000000000..333c306aa946 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-plybas.dts @@ -0,0 +1,394 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2014 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel , Pengutronix + */ + +/dts-v1/; +#include +#include +#include "imx6dl.dtsi" + +/ { + model = "Plymovent BAS board"; + compatible = "ply,plybas", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + autorepeat; + + button@20 { + label = "START"; + linux,code = <31>; + gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; + }; + + button@21 { + label = "CLEAN"; + linux,code = <46>; + gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "debug0"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + + led-1 { + label = "debug1"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + + led-2 { + label = "light_tower1"; + gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-3 { + label = "light_tower2"; + gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>; + }; + + led-4 { + label = "light_tower3"; + gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; + }; + + led-5 { + label = "light_tower4"; + gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>; + }; + }; + + clk50m_phy: phy-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + reg_5v0: regulator-5v0 { + compatible = "regulator-fixed"; + regulator-name = "5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + xceiver-supply = <®_5v0>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + xceiver-supply = <®_5v0>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clk50m_phy>; + clock-names = "ipg", "ahb", "ptp"; + phy-handle = <&rgmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rgmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "", "SD1_CD", "", "", "", "", "", "", + "DEBUG_0", "DEBUG_1", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "CAN1_SR", "CAN2_SR", "", "", + "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI", + "IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2", + "IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD", + "IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "", + "IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5", + "IMX6_IN6", "IMX6_IN7", "IMX6_IN8", + "IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + fsl,uart-has-rtscts; + linux,rs485-enabled-at-boot-time; + rs485-rts-delay = <0 20>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usbphynop1 { + status = "disabled"; +}; + +&usbphynop2 { + status = "disabled"; +}; + +&iomuxc { + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000 + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008 + /* CAN2_SR */ + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x1b000 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x3008 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x3008 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x3008 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + /* DEBUG_0 */ + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0 + /* DEBUG_1 */ + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 + + /* LED1 (lighttower) */ + MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22 0x13070 + /* LED2 (lighttower) */ + MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23 0x13070 + /* LED3 (lighttower) */ + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x13070 + /* LED4 (lighttower) */ + MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x13070 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + >; + }; + + /* YaCO AUX Uart */ + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x130b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; +}; From c8ed7211bf12642ff063f4e71bb902c48b0b304b Mon Sep 17 00:00:00 2001 From: Mans Rullgard Date: Wed, 9 Dec 2020 23:09:03 +0100 Subject: [PATCH 126/584] ARM: dts: imx28: add pinmux for USB1 overcurrent on pwm2 Add pinmux setting for USB1 overcurrent on pwm2 pad. Signed-off-by: Mans Rullgard Signed-off-by: Lukasz Majewski Reviewed-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx28.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index bbe52150b165..84d0176d5193 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -948,6 +948,16 @@ fsl,pull-up = ; }; + usb1_pins_b: usb1@1 { + reg = <1>; + fsl,pinmux-ids = < + MX28_PAD_PWM2__USB1_OVERCURRENT + >; + fsl,drive-strength = ; + fsl,voltage = ; + fsl,pull-up = ; + }; + usb0_id_pins_a: usb0id@0 { reg = <0>; fsl,pinmux-ids = < From 3069a84fd67b05a3125e80cd7e2f7ea516421137 Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Wed, 6 Jan 2021 19:19:00 +0100 Subject: [PATCH 127/584] dt-bindings: media: Add Allwinner R40 deinterlace compatible Allwinner R40 SoC also contains deinterlace core, compatible to H3. Add compatible string for it. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210106181901.1324075-2-jernej.skrabec@siol.net --- .../bindings/media/allwinner,sun8i-h3-deinterlace.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml index 6a56214c6cfd..b80980b1908e 100644 --- a/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml +++ b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml @@ -19,6 +19,9 @@ properties: compatible: oneOf: - const: allwinner,sun8i-h3-deinterlace + - items: + - const: allwinner,sun8i-r40-deinterlace + - const: allwinner,sun8i-h3-deinterlace - items: - const: allwinner,sun50i-a64-deinterlace - const: allwinner,sun8i-h3-deinterlace From 62de535663e8bf4a5442bb11de7e4926a00eb93c Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Wed, 6 Jan 2021 19:19:01 +0100 Subject: [PATCH 128/584] ARM: dts: sun8i: r40: Add deinterlace node R40 contains deinterlace core compatible to that in H3. One peculiarity is that RAM gate is shared with CSI1. User manual states it's separate but that's not true. Shared gate was verified with BSP Linux code check and with runtime tests (CPU crashed if CSI1 gate was not ungated). Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210106181901.1324075-3-jernej.skrabec@siol.net --- arch/arm/boot/dts/sun8i-r40.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi index 7907569e7b5c..d5ad3b9efd12 100644 --- a/arch/arm/boot/dts/sun8i-r40.dtsi +++ b/arch/arm/boot/dts/sun8i-r40.dtsi @@ -190,6 +190,25 @@ }; }; + deinterlace: deinterlace@1400000 { + compatible = "allwinner,sun8i-r40-deinterlace", + "allwinner,sun8i-h3-deinterlace"; + reg = <0x01400000 0x20000>; + clocks = <&ccu CLK_BUS_DEINTERLACE>, + <&ccu CLK_DEINTERLACE>, + /* + * NOTE: Contrary to what datasheet claims, + * DRAM deinterlace gate doesn't exist and + * it's shared with CSI1. + */ + <&ccu CLK_DRAM_CSI1>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_DEINTERLACE>; + interrupts = ; + interconnects = <&mbus 9>; + interconnect-names = "dma-mem"; + }; + syscon: system-control@1c00000 { compatible = "allwinner,sun8i-r40-system-control", "allwinner,sun4i-a10-system-control"; From 086b4f7afdeda24adabcb199cd23a5055b0cbe7b Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Wed, 6 Jan 2021 19:25:23 +0100 Subject: [PATCH 129/584] arm64: dts: allwinner: h5: Add deinterlace node Deinterlace core is completely compatible to H3. Add a node for it. Signed-off-by: Jernej Skrabec Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210106182523.1325796-1-jernej.skrabec@siol.net --- arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi index 10489e508695..578a63dedf46 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi @@ -121,6 +121,19 @@ resets = <&ccu RST_BUS_CE>; }; + deinterlace: deinterlace@1e00000 { + compatible = "allwinner,sun8i-h3-deinterlace"; + reg = <0x01e00000 0x20000>; + clocks = <&ccu CLK_BUS_DEINTERLACE>, + <&ccu CLK_DEINTERLACE>, + <&ccu CLK_DRAM_DEINTERLACE>; + clock-names = "bus", "mod", "ram"; + resets = <&ccu RST_BUS_DEINTERLACE>; + interrupts = ; + interconnects = <&mbus 9>; + interconnect-names = "dma-mem"; + }; + mali: gpu@1e80000 { compatible = "allwinner,sun50i-h5-mali", "arm,mali-450"; reg = <0x01e80000 0x30000>; From f772081f48831f68dc4c53f58bb28077c3cd52a7 Mon Sep 17 00:00:00 2001 From: Douglas Anderson Date: Wed, 6 Jan 2021 15:25:49 -0800 Subject: [PATCH 130/584] arm64: dts: qcom: sc7180: Add "dp_hot_plug_det" pinconf for trogdor We have an external pull on this line, so disable the internal pull. Signed-off-by: Douglas Anderson Link: https://lore.kernel.org/r/20210106152537.1.Ib4b5b0e88fdc825c0e2662bab982dda8af2297b2@changeid Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index d76200d2b373..e3a3d809448f 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -936,6 +936,13 @@ ap_spi_fp: &spi10 { /* PINCTRL - additions to nodes defined in sc7180.dtsi */ +&dp_hot_plug_det { + pinconf { + pins = "gpio117"; + bias-disable; + }; +}; + &qspi_cs0 { pinconf { pins = "gpio68"; From 826e6faf49ae1eb065759a30832a2e34740bd8b1 Mon Sep 17 00:00:00 2001 From: Stephan Gerhold Date: Wed, 6 Jan 2021 11:21:34 +0100 Subject: [PATCH 131/584] arm64: dts: qcom: msm8916-samsung-a5u: Fix iris compatible Unlike most MSM8916 boards, samsung-a5u uses WCN3660B instead of WCN3620 to support the 5 GHz band additionally. WCN3660B has similar requirements as WCN3620, but it needs the XO clock to run at 48 MHz instead of 19.2 MHz. So far it was possible to describe that configuration using the qcom,wcn3680 compatible. However, as of commit 8490987bdb9a ("wcn36xx: Hook and identify RF_IRIS_WCN3680"), the wcn36xx driver will now use the qcom,wcn3680 compatible to enable functionality specific to WCN3680. In particular, WCN3680 supports 802.11ac, which is not available in WCN3660B. Use the new qcom,wcn3660b compatible to describe the chip properly. Fixes: 0d7051999175 ("arm64: dts: msm8916-samsung-a5u: Override iris compatible") Signed-off-by: Stephan Gerhold Link: https://lore.kernel.org/r/20210106102134.59801-4-stephan@gerhold.net Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts index e39c04d977c2..dd35c3344358 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts @@ -38,7 +38,7 @@ &pronto { iris { - compatible = "qcom,wcn3680"; + compatible = "qcom,wcn3660b"; }; }; From b82a27075a0402386ba61c0404b47b69e7dc7911 Mon Sep 17 00:00:00 2001 From: Dinh Nguyen Date: Tue, 5 Jan 2021 14:55:20 -0600 Subject: [PATCH 132/584] ARM: dts: arria10: add PMU node Add the PMU node for Arria10. Signed-off-by: Dinh Nguyen --- arch/arm/boot/dts/socfpga_arria10.dtsi | 13 +++++++++++-- 1 file changed, 11 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/socfpga_arria10.dtsi index 0013ec3463c4..a574ea91d9d3 100644 --- a/arch/arm/boot/dts/socfpga_arria10.dtsi +++ b/arch/arm/boot/dts/socfpga_arria10.dtsi @@ -15,13 +15,13 @@ #size-cells = <0>; enable-method = "altr,socfpga-a10-smp"; - cpu@0 { + cpu0: cpu@0 { compatible = "arm,cortex-a9"; device_type = "cpu"; reg = <0>; next-level-cache = <&L2>; }; - cpu@1 { + cpu1: cpu@1 { compatible = "arm,cortex-a9"; device_type = "cpu"; reg = <1>; @@ -29,6 +29,15 @@ }; }; + pmu: pmu@ff111000 { + compatible = "arm,cortex-a9-pmu"; + interrupt-parent = <&intc>; + interrupts = <0 124 4>, <0 125 4>; + interrupt-affinity = <&cpu0>, <&cpu1>; + reg = <0xff111000 0x1000>, + <0xff113000 0x1000>; + }; + intc: intc@ffffd000 { compatible = "arm,cortex-a9-gic"; #interrupt-cells = <3>; From 36948ec3d4d0d1b9260d87b550a56fab8d86d17d Mon Sep 17 00:00:00 2001 From: Demetris Ierokipides Date: Fri, 8 Jan 2021 17:10:35 +0200 Subject: [PATCH 133/584] ARM: dts: rockchip: add gpu node to rk3288-miqi Add the Mali GPU node to the MiQi device-tree. Signed-off-by: Demetris Ierokipides Link: https://lore.kernel.org/r/20210108151036.36434-2-ierokipides.dem@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288-miqi.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/rk3288-miqi.dts b/arch/arm/boot/dts/rk3288-miqi.dts index cf54d5ffff2f..713f55e143c6 100644 --- a/arch/arm/boot/dts/rk3288-miqi.dts +++ b/arch/arm/boot/dts/rk3288-miqi.dts @@ -123,6 +123,11 @@ status = "okay"; }; +&gpu { + mali-supply = <&vdd_gpu>; + status = "okay"; +}; + &hdmi { ddc-i2c-bus = <&i2c5>; status = "okay"; From 221c6c042fa004b73b10780fa2aaf177085e2f3f Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sat, 19 Dec 2020 22:05:00 +0100 Subject: [PATCH 134/584] arm64: dts: rockchip: assign a fixed index to mmc devices on rk3328 boards Recently introduced async probe on mmc devices can shuffle block IDs. Pin them to fixed values to ease booting in environments where UUIDs are not practical. Use newly introduced aliases for mmcblk devices from [1]. [1] https://patchwork.kernel.org/patch/11747669/ Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20201219210500.3855-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3328.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi index db0d5c8e5f96..56b5ee7e54c4 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi @@ -27,6 +27,9 @@ i2c1 = &i2c1; i2c2 = &i2c2; i2c3 = &i2c3; + mmc0 = &sdmmc; + mmc1 = &sdio; + mmc2 = &emmc; ethernet0 = &gmac2io; ethernet1 = &gmac2phy; }; From b39d9683c72122c8ac914c3701213b7b9002f2c8 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 6 Dec 2020 11:37:08 +0100 Subject: [PATCH 135/584] ARM: dts: rockchip: add QoS register compatibles for rk3066/rk3188 With the conversion of syscon.yaml minItems for compatibles was set to 2. Current Rockchip dtsi files only use "syscon" for QoS registers. Add Rockchip QoS compatibles for rk3066/rk3188 to reduce notifications produced with: make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20201206103711.7465-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3xxx.dtsi | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rk3xxx.dtsi index 859a7477909f..49bcdf46d03c 100644 --- a/arch/arm/boot/dts/rk3xxx.dtsi +++ b/arch/arm/boot/dts/rk3xxx.dtsi @@ -151,42 +151,42 @@ }; qos_gpu: qos@1012d000 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012d000 0x20>; }; qos_vpu: qos@1012e000 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012e000 0x20>; }; qos_lcdc0: qos@1012f000 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012f000 0x20>; }; qos_cif0: qos@1012f080 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012f080 0x20>; }; qos_ipp: qos@1012f100 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012f100 0x20>; }; qos_lcdc1: qos@1012f180 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012f180 0x20>; }; qos_cif1: qos@1012f200 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012f200 0x20>; }; qos_rga: qos@1012f280 { - compatible = "syscon"; + compatible = "rockchip,rk3066-qos", "syscon"; reg = <0x1012f280 0x20>; }; From 6cc35e5edbe43ec6e510e6c53b8c88ae7b1666c2 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 6 Dec 2020 11:37:09 +0100 Subject: [PATCH 136/584] ARM: dts: rockchip: add QoS register compatibles for rk3288 With the conversion of syscon.yaml minItems for compatibles was set to 2. Current Rockchip dtsi files only use "syscon" for QoS registers. Add Rockchip QoS compatibles for rk3288 to reduce notifications produced with: make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20201206103711.7465-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288.dtsi | 28 ++++++++++++++-------------- 1 file changed, 14 insertions(+), 14 deletions(-) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 68d5a58cfe88..01ea1f170f77 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -1329,72 +1329,72 @@ }; qos_gpu_r: qos@ffaa0000 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffaa0000 0x0 0x20>; }; qos_gpu_w: qos@ffaa0080 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffaa0080 0x0 0x20>; }; qos_vio1_vop: qos@ffad0000 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0000 0x0 0x20>; }; qos_vio1_isp_w0: qos@ffad0100 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0100 0x0 0x20>; }; qos_vio1_isp_w1: qos@ffad0180 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0180 0x0 0x20>; }; qos_vio0_vop: qos@ffad0400 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0400 0x0 0x20>; }; qos_vio0_vip: qos@ffad0480 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0480 0x0 0x20>; }; qos_vio0_iep: qos@ffad0500 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0500 0x0 0x20>; }; qos_vio2_rga_r: qos@ffad0800 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0800 0x0 0x20>; }; qos_vio2_rga_w: qos@ffad0880 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0880 0x0 0x20>; }; qos_vio1_isp_r: qos@ffad0900 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffad0900 0x0 0x20>; }; qos_video: qos@ffae0000 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffae0000 0x0 0x20>; }; qos_hevc_r: qos@ffaf0000 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffaf0000 0x0 0x20>; }; qos_hevc_w: qos@ffaf0080 { - compatible = "syscon"; + compatible = "rockchip,rk3288-qos", "syscon"; reg = <0x0 0xffaf0080 0x0 0x20>; }; From bd3fd04910ab5e4d571c19f50c341de175597dfa Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 6 Dec 2020 11:37:10 +0100 Subject: [PATCH 137/584] arm64: dts: rockchip: add QoS register compatibles for rk3399 With the conversion of syscon.yaml minItems for compatibles was set to 2. Current Rockchip dtsi files only use "syscon" for QoS registers. Add Rockchip QoS compatibles for rk3399 to reduce notifications produced with: make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20201206103711.7465-3-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3399.dtsi | 50 ++++++++++++------------ 1 file changed, 25 insertions(+), 25 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index f5dee5f447bb..cd9fbd3cfcaf 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -858,127 +858,127 @@ }; qos_emmc: qos@ffa58000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa58000 0x0 0x20>; }; qos_gmac: qos@ffa5c000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa5c000 0x0 0x20>; }; qos_pcie: qos@ffa60080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa60080 0x0 0x20>; }; qos_usb_host0: qos@ffa60100 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa60100 0x0 0x20>; }; qos_usb_host1: qos@ffa60180 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa60180 0x0 0x20>; }; qos_usb_otg0: qos@ffa70000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa70000 0x0 0x20>; }; qos_usb_otg1: qos@ffa70080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa70080 0x0 0x20>; }; qos_sd: qos@ffa74000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa74000 0x0 0x20>; }; qos_sdioaudio: qos@ffa76000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa76000 0x0 0x20>; }; qos_hdcp: qos@ffa90000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa90000 0x0 0x20>; }; qos_iep: qos@ffa98000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffa98000 0x0 0x20>; }; qos_isp0_m0: qos@ffaa0000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffaa0000 0x0 0x20>; }; qos_isp0_m1: qos@ffaa0080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffaa0080 0x0 0x20>; }; qos_isp1_m0: qos@ffaa8000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffaa8000 0x0 0x20>; }; qos_isp1_m1: qos@ffaa8080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffaa8080 0x0 0x20>; }; qos_rga_r: qos@ffab0000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffab0000 0x0 0x20>; }; qos_rga_w: qos@ffab0080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffab0080 0x0 0x20>; }; qos_video_m0: qos@ffab8000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffab8000 0x0 0x20>; }; qos_video_m1_r: qos@ffac0000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffac0000 0x0 0x20>; }; qos_video_m1_w: qos@ffac0080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffac0080 0x0 0x20>; }; qos_vop_big_r: qos@ffac8000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffac8000 0x0 0x20>; }; qos_vop_big_w: qos@ffac8080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffac8080 0x0 0x20>; }; qos_vop_little: qos@ffad0000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffad0000 0x0 0x20>; }; qos_perihp: qos@ffad8080 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffad8080 0x0 0x20>; }; qos_gpu: qos@ffae0000 { - compatible = "syscon"; + compatible = "rockchip,rk3399-qos", "syscon"; reg = <0x0 0xffae0000 0x0 0x20>; }; From 6c3ae9f9a133d387ef4e1b4297c9df4e9a1c469d Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 6 Dec 2020 11:37:11 +0100 Subject: [PATCH 138/584] arm64: dts: rockchip: add QoS register compatibles for px30 With the conversion of syscon.yaml minItems for compatibles was set to 2. Current Rockchip dtsi files only use "syscon" for QoS registers. Add Rockchip QoS compatibles for px30 to reduce notifications produced with: make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/mfd/syscon.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20201206103711.7465-4-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/px30.dtsi | 40 +++++++++++++------------- 1 file changed, 20 insertions(+), 20 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi index 2695ea8cda14..af6bcef9e848 100644 --- a/arch/arm64/boot/dts/rockchip/px30.dtsi +++ b/arch/arm64/boot/dts/rockchip/px30.dtsi @@ -1107,102 +1107,102 @@ }; qos_gmac: qos@ff518000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff518000 0x0 0x20>; }; qos_gpu: qos@ff520000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff520000 0x0 0x20>; }; qos_sdmmc: qos@ff52c000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff52c000 0x0 0x20>; }; qos_emmc: qos@ff538000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff538000 0x0 0x20>; }; qos_nand: qos@ff538080 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff538080 0x0 0x20>; }; qos_sdio: qos@ff538100 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff538100 0x0 0x20>; }; qos_sfc: qos@ff538180 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff538180 0x0 0x20>; }; qos_usb_host: qos@ff540000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff540000 0x0 0x20>; }; qos_usb_otg: qos@ff540080 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff540080 0x0 0x20>; }; qos_isp_128: qos@ff548000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff548000 0x0 0x20>; }; qos_isp_rd: qos@ff548080 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff548080 0x0 0x20>; }; qos_isp_wr: qos@ff548100 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff548100 0x0 0x20>; }; qos_isp_m1: qos@ff548180 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff548180 0x0 0x20>; }; qos_vip: qos@ff548200 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff548200 0x0 0x20>; }; qos_rga_rd: qos@ff550000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff550000 0x0 0x20>; }; qos_rga_wr: qos@ff550080 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff550080 0x0 0x20>; }; qos_vop_m0: qos@ff550100 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff550100 0x0 0x20>; }; qos_vop_m1: qos@ff550180 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff550180 0x0 0x20>; }; qos_vpu: qos@ff558000 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff558000 0x0 0x20>; }; qos_vpu_r128: qos@ff558080 { - compatible = "syscon"; + compatible = "rockchip,px30-qos", "syscon"; reg = <0x0 0xff558080 0x0 0x20>; }; From 25572fb5aa986bdbb35d06c0fb52a9b9d9b3b2c9 Mon Sep 17 00:00:00 2001 From: Katsuhiro Suzuki Date: Mon, 3 Aug 2020 00:42:31 +0900 Subject: [PATCH 139/584] arm64: dts: rockchip: enable HDMI sound nodes for rk3328-rock64 This patch enables HDMI sound (I2S0) and Analog sound (I2S1) which are defined in rk3328.dtsi, and replace SPDIF nodes. We can use SPDIF pass-through with suitable ALSA settings and on mpv or other media players. - Settings: https://github.com/LibreELEC/LibreELEC.tv/blob/master/projects/Rockchip/filesystem/usr/share/alsa/cards/SPDIF.conf - Ex.: mpv foo.ac3 --audio-spdif=ac3 --audio-device='alsa/SPDIF.pcm.iec958.0:SPDIF' [Why use simple-audio-card for SPDIF?] For newly adding nodes, ASoC guys recommend to use audio-graph-card. But all other sound nodes for rk3328 have already been defined by simple-audio-card. In this time, I chose for consistent sound nodes. [DMA allocation problem] After this patch is applied, UART2 will fail to allocate DMA resources but UART driver can work fine without DMA. This error is related to the DMAC of rk3328 (pl330 or compatible). DMAC connected to 16 DMA sources. Each sources have ID number that is called 'Req number' in rk3328 TRM. After this patch is applied total 7 of DMA sources will be activated as follows: | Req number | Source | Required | | | | channels | |------------+--------+-----------| | 8, 9 | SPI0 | 2ch | | 11, 12 | I2S0 | 2ch | | 14, 15 | I2S1 | 2ch | | 10 | SPDIF | 1ch | |------------+--------+-----------| | | Total | 7ch | |------------+--------+-----------| | 6, 7 | UART2 | 2ch | -> cannot get DMA channels Due to rk3328 DMAC specification we can use max 8 channels at same time. If SPI0/I2S0/I2S1/SPDIF will be activated by this patch, required DMAC channels reach to 7. So the last two channels (for UART2) cannot get DMA resources. Virt-dma mechanism for pl0330 DMAC driver is needed to fix this problem. Signed-off-by: Katsuhiro Suzuki Link: https://lore.kernel.org/r/20200802154231.2639186-1-katsuhiro@katsuster.net Signed-off-by: Heiko Stuebner --- .../arm64/boot/dts/rockchip/rk3328-rock64.dts | 58 ++++++++----------- 1 file changed, 25 insertions(+), 33 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts index 86cfb5c50a94..c984662043da 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock64.dts @@ -84,34 +84,32 @@ }; }; - sound { - compatible = "audio-graph-card"; - label = "rockchip,rk3328"; - dais = <&i2s1_p0 - &spdif_p0>; - }; + spdif_sound: spdif-sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "SPDIF"; - spdif-dit { - compatible = "linux,spdif-dit"; - #sound-dai-cells = <0>; + simple-audio-card,cpu { + sound-dai = <&spdif>; + }; - port { - dit_p0_0: endpoint { - remote-endpoint = <&spdif_p0_0>; - }; + simple-audio-card,codec { + sound-dai = <&spdif_dit>; }; }; + + spdif_dit: spdif-dit { + compatible = "linux,spdif-dit"; + #sound-dai-cells = <0>; + }; +}; + +&analog_sound { + status = "okay"; }; &codec { mute-gpios = <&grf_gpio 0 GPIO_ACTIVE_LOW>; status = "okay"; - - port@0 { - codec_p0_0: endpoint { - remote-endpoint = <&i2s1_p0_0>; - }; - }; }; &cpu0 { @@ -163,6 +161,10 @@ status = "okay"; }; +&hdmi_sound { + status = "okay"; +}; + &hdmiphy { status = "okay"; }; @@ -278,16 +280,12 @@ }; }; +&i2s0 { + status = "okay"; +}; + &i2s1 { status = "okay"; - - i2s1_p0: port { - i2s1_p0_0: endpoint { - dai-format = "i2s"; - mclk-fs = <256>; - remote-endpoint = <&codec_p0_0>; - }; - }; }; &io_domains { @@ -337,12 +335,6 @@ &spdif { pinctrl-0 = <&spdifm0_tx>; status = "okay"; - - spdif_p0: port { - spdif_p0_0: endpoint { - remote-endpoint = <&dit_p0_0>; - }; - }; }; &spi0 { From 7f02feb56d9dc8ee2fffe00993f7b9aadd8902ba Mon Sep 17 00:00:00 2001 From: Katsuhiro Suzuki Date: Mon, 10 Aug 2020 18:16:19 +0900 Subject: [PATCH 140/584] arm64: dts: rockchip: add SPDIF node for rk3399-rockpro64 This patch adds 'disabled' SPDIF sound node and related settings for rk3399-rockpro64. There are 2 reasons: - All RK3399 dma-bus channels have been already used by I2S0/1/2 - RockPro64 does not have SPDIF optical nor coaxial connector, just have 3pins Signed-off-by: Katsuhiro Suzuki Link: https://lore.kernel.org/r/20200810091619.3170534-1-katsuhiro@katsuster.net Signed-off-by: Heiko Stuebner --- .../boot/dts/rockchip/rk3399-rockpro64.dtsi | 27 +++++++++++++++++++ 1 file changed, 27 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi index 6e553ff47534..58097245994a 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi @@ -76,6 +76,23 @@ dais = <&i2s1_p0>; }; + sound-dit { + compatible = "audio-graph-card"; + label = "rockchip,rk3399"; + dais = <&spdif_p0>; + }; + + spdif-dit { + compatible = "linux,spdif-dit"; + #sound-dai-cells = <0>; + + port { + dit_p0_0: endpoint { + remote-endpoint = <&spdif_p0_0>; + }; + }; + }; + vcc12v_dcin: vcc12v-dcin { compatible = "regulator-fixed"; regulator-name = "vcc12v_dcin"; @@ -698,6 +715,16 @@ status = "okay"; }; +&spdif { + pinctrl-0 = <&spdif_bus_1>; + + spdif_p0: port { + spdif_p0_0: endpoint { + remote-endpoint = <&dit_p0_0>; + }; + }; +}; + &spi1 { status = "okay"; From edb93de429f97685f0793d4ad56ab3cbc630fa1e Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Thu, 17 Dec 2020 16:13:13 +0100 Subject: [PATCH 141/584] arm64: dts: imx8mq-librem5-devkit: Tweak pmic regulators MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit BUCK3 needs a regulator-enable-ramp-delay since otherwise the board freezes on etnaviv probe. With this pgc_gpu suspends and resumes as expected. This must have been always broken since gpcv2 support was enabled. We also enable all the regulators needed for Deep Sleep Mode (DSM) as always-on: - VDD_SOC supplied by BUCK1 - VDDA_1P8 supplied by BUCK7 - VDDA_0P9 supplied by LDO4 - VDDA_DRAM supplied by LDO3 - NVCC_DRAM supplied by BUCK8 - VDD_DRAM supplied by BUCK5 Finally LDO5 and LDO6 provide VDD_PHY_1V8 and VDD_PHY_0V9 used by the SOCs MIPI, HDMI and USB IP cores. While we would in theory be able to turn these off (and I've tested that or LDO6 and mipi with USB disabled) it is of little practical use atm since USB doesn't runtime suspend so let's revisit this at a later point. Signed-off-by: Guido Günther Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- .../boot/dts/freescale/imx8mq-librem5-devkit.dts | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts index af139b283daf..f35d6897fbf7 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts @@ -298,6 +298,7 @@ regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-always-on; regulator-ramp-delay = <1250>; rohm,dvs-run-voltage = <900000>; rohm,dvs-idle-voltage = <850000>; @@ -319,6 +320,7 @@ regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; regulator-boot-on; + regulator-enable-ramp-delay = <200>; rohm,dvs-run-voltage = <900000>; }; @@ -334,6 +336,7 @@ regulator-min-microvolt = <700000>; regulator-max-microvolt = <1350000>; regulator-boot-on; + regulator-always-on; }; buck6_reg: BUCK6 { @@ -341,6 +344,7 @@ regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3300000>; regulator-boot-on; + regulator-always-on; }; buck7_reg: BUCK7 { @@ -348,6 +352,7 @@ regulator-min-microvolt = <1605000>; regulator-max-microvolt = <1995000>; regulator-boot-on; + regulator-always-on; }; buck8_reg: BUCK8 { @@ -355,6 +360,7 @@ regulator-min-microvolt = <800000>; regulator-max-microvolt = <1400000>; regulator-boot-on; + regulator-always-on; }; ldo1_reg: LDO1 { @@ -380,6 +386,7 @@ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; + regulator-always-on; }; ldo4_reg: LDO4 { @@ -387,12 +394,14 @@ regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; + regulator-always-on; }; ldo5_reg: LDO5 { regulator-name = "ldo5"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; + regulator-always-on; }; ldo6_reg: LDO6 { @@ -400,6 +409,7 @@ regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; regulator-boot-on; + regulator-always-on; }; ldo7_reg: LDO7 { @@ -407,6 +417,7 @@ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; regulator-boot-on; + regulator-always-on; }; }; }; From ff38c1ddbb1cee7c87b186136c9591803b31aceb Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Thu, 17 Dec 2020 16:13:14 +0100 Subject: [PATCH 142/584] arm64: dts: imx8mq-librem5-devkit: Disable snvs_rtc MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The board has it's own RTC chip which is backed by the (optional) battery and hence preserves data/time on poweroff when that is inserted. Signed-off-by: Guido Günther Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts index f35d6897fbf7..05a43ee6d051 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts @@ -897,6 +897,10 @@ status = "okay"; }; +&snvs_rtc { + status = "disabled"; +}; + &sai2 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_sai2>; From 48563c054f599d0fa29011eef7423dd0c67d1b55 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Thu, 17 Dec 2020 16:13:15 +0100 Subject: [PATCH 143/584] arm64: dts: imx8mq-librem5-devkit: Drop custom clock settings MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Otherwise the boot hangs early on and the resulting clock tree without this already closely matches the selected rates (722534400 and 786432000). audio_pll2 0 0 0 722534397 0 0 50000 audio_pll2_bypass 0 0 0 722534397 0 0 50000 audio_pll2_out 0 0 0 722534397 0 0 50000 audio_pll1 1 1 0 786431998 0 0 50000 audio_pll1_bypass 1 1 0 786431998 0 0 50000 audio_pll1_out 1 1 0 786431998 0 0 50000 sai2 1 1 0 24576000 0 0 50000 sai2_root_clk 1 1 0 24576000 0 0 50000 sai6 0 0 0 24576000 0 0 50000 sai6_root_clk 0 0 0 24576000 0 0 50000 Signed-off-by: Guido Günther Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 5 ----- 1 file changed, 5 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts index 05a43ee6d051..dd217a0760e9 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts @@ -244,11 +244,6 @@ cpu-supply = <&buck2_reg>; }; -&clk { - assigned-clocks = <&clk IMX8MQ_AUDIO_PLL1>, <&clk IMX8MQ_AUDIO_PLL2>; - assigned-clock-rates = <786432000>, <722534400>; -}; - &dphy { status = "okay"; }; From 190621e0f6094001790b364900086448c1b12cf5 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 17 Dec 2020 11:25:29 -0600 Subject: [PATCH 144/584] arm64: dts: imx8mm-beacon: Drop unused clock-names reference The wlf,wm8962 driver does not use the clock-names property. Drop it. Signed-off-by: Adam Ford Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi index d6b9dedd168f..6f5e63696ec0 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi @@ -102,7 +102,6 @@ compatible = "wlf,wm8962"; reg = <0x1a>; clocks = <&clk IMX8MM_CLK_SAI3_ROOT>; - clock-names = "xclk"; DCVDD-supply = <®_audio>; DBVDD-supply = <®_audio>; AVDD-supply = <®_audio>; From f9eb60d574074f40458f63f72d3377ad42d9fc32 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 17 Dec 2020 11:25:28 -0600 Subject: [PATCH 145/584] ARM: dts: imx6q-logicpd: Drop unused clock-names reference The wlf,wm8962 driver does not use the clock-names property. Drop it. Signed-off-by: Adam Ford Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi index 665d63765cdc..d9de9b4f0c52 100644 --- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi +++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi @@ -238,7 +238,6 @@ compatible = "wlf,wm8962"; reg = <0x1a>; clocks = <&clks IMX6QDL_CLK_CKO>; - clock-names = "xclk"; DCVDD-supply = <®_audio>; DBVDD-supply = <®_audio>; AVDD-supply = <®_audio>; From 62270eeb2b639ed840ee133e301073057d497ed8 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Sun, 10 Jan 2021 17:55:51 +0100 Subject: [PATCH 146/584] arm64: dts: imx8mq: Add clock parents for mipi dphy MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This makes sure the clock tree setup for the dphy is not dependent on other components. Without this change bringing up the display can fail like kernel: phy phy-30a00300.dphy.2: Invalid CM/CN/CO values: 165/217/1 kernel: phy phy-30a00300.dphy.2: for hs_clk/ref_clk=451656000/593999998 ~ 165/217 if LCDIF doesn't set up that part of the clock tree first. This was noticed when testing the Librem 5 devkit with defconfig. It doesn't happen when modules are built in. Signed-off-by: Guido Günther Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index a841a023e8e0..50ae17f65a51 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -1016,9 +1016,14 @@ reg = <0x30a00300 0x100>; clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; clock-names = "phy_ref"; - assigned-clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; - assigned-clock-parents = <&clk IMX8MQ_VIDEO_PLL1_OUT>; - assigned-clock-rates = <24000000>; + assigned-clocks = <&clk IMX8MQ_VIDEO_PLL1_REF_SEL>, + <&clk IMX8MQ_VIDEO_PLL1_BYPASS>, + <&clk IMX8MQ_CLK_DSI_PHY_REF>, + <&clk IMX8MQ_VIDEO_PLL1>; + assigned-clock-parents = <&clk IMX8MQ_CLK_25M>, + <&clk IMX8MQ_VIDEO_PLL1>, + <&clk IMX8MQ_VIDEO_PLL1_OUT>; + assigned-clock-rates = <0>, <0>, <24000000>, <594000000>; #phy-cells = <0>; power-domains = <&pgc_mipi>; status = "disabled"; From 84b1f57d10679e4b20b0ddee001b03b062d8c90f Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Tue, 22 Dec 2020 16:13:44 +0100 Subject: [PATCH 147/584] arm64: dts: imx8mq-librem5: add vin-supply to VDD_1V8 buck7 is the supply here. Also, fix alphabetical ordering. Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 15 ++++++++------- 1 file changed, 8 insertions(+), 7 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 64fc546b110f..55268fc0622e 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -99,6 +99,14 @@ regulator-max-microvolt = <3300000>; }; + reg_vdd_1v8: regulator-vdd-1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&buck7_reg>; + }; + reg_vdd_3v3: regulator-vdd-3v3 { compatible = "regulator-fixed"; regulator-name = "VDD_3V3"; @@ -106,13 +114,6 @@ regulator-max-microvolt = <3300000>; }; - reg_vdd_1v8: regulator-vdd-1v8 { - compatible = "regulator-fixed"; - regulator-name = "VCC_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - }; - reg_vsys_3v4: regulator-vsys-3v4 { compatible = "regulator-fixed"; regulator-name = "VSYS_3V4"; From c003b15b4c102f9c34f4f77978c8d9b2707d7f53 Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Tue, 22 Dec 2020 16:13:45 +0100 Subject: [PATCH 148/584] arm64: dts: imx8mq-librem5: add pinctrl for the touchscreen description In order for the touchscreen interrupt line to work, describe it properly. Otherwise it can work if defaults are ok, but we cannot be sure. Fixes: 8f0216b006e5 ("arm64: dts: Add a device tree for the Librem 5 phone") Signed-off-by: Martin Kepplinger Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 55268fc0622e..8fceecabd6b4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -459,6 +459,13 @@ >; }; + pinctrl_touch: touchgrp { + fsl,pins = < + /* TP_INT */ + MX8MQ_IOMUXC_ENET_RD1_GPIO1_IO27 0x80 + >; + }; + pinctrl_typec: typecgrp { fsl,pins = < /* TYPEC_MUX_EN */ @@ -880,6 +887,8 @@ touchscreen@38 { compatible = "edt,edt-ft5506"; reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touch>; interrupt-parent = <&gpio1>; interrupts = <27 IRQ_TYPE_EDGE_FALLING>; touchscreen-size-x = <720>; From 6a67d8fbee56c2e99cf71bddbd55ab1e39dd682a Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Tue, 22 Dec 2020 16:13:46 +0100 Subject: [PATCH 149/584] arm64: dts: imx8mq-librem5: Move usdhc clocks assignment to board DT According to commit e045f044e84e ("arm64: dts: imx8mq: Move usdhc clocks assignment to board DT") add the clocks assignment to imx8mq-librem5.dtsi too. Fixes: e045f044e84e ("arm64: dts: imx8mq: Move usdhc clocks assignment to board DT") Signed-off-by: Martin Kepplinger Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 8fceecabd6b4..f85d30a0c2cb 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -1082,6 +1082,8 @@ }; &usdhc1 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>; + assigned-clock-rates = <400000000>; pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; pinctrl-1 = <&pinctrl_usdhc1_100mhz>; @@ -1094,6 +1096,8 @@ }; &usdhc2 { + assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>; + assigned-clock-rates = <200000000>; pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc2>; pinctrl-1 = <&pinctrl_usdhc2_100mhz>; From 1773b8d6697ac8e9380843fe5c13c25e95baa702 Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Tue, 22 Dec 2020 16:13:47 +0100 Subject: [PATCH 150/584] arm64: dts: imx8mq-librem5-r3: workaround i2c1 issue with 1GHz cpu voltage This is a workaround for a hardware bug in the r3 revision that basically would stop the system due to traffic on the i2c1 bus. A cpu voltage change would trigger such traffic and that's what is avoided in order to work around it. Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts index 6704ea2c72a3..0d38327043f8 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts @@ -10,6 +10,12 @@ compatible = "purism,librem5r3", "purism,librem5", "fsl,imx8mq"; }; +&a53_opp_table { + opp-1000000000 { + opp-microvolt = <1000000>; + }; +}; + &accel_gyro { mount-matrix = "1", "0", "0", "0", "1", "0", From 70db442df67c79e8fc49e580e8a483aabc42ed3b Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:34 +0100 Subject: [PATCH 151/584] arm64: dts: ls1012a: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 60 +++++++++++++------ 1 file changed, 43 insertions(+), 17 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi index 626b709d1fb9..7de6b376d792 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi @@ -7,6 +7,7 @@ * */ +#include #include #include @@ -34,7 +35,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; #cooling-cells = <2>; cpu-idle-states = <&CPU_PH20>; }; @@ -148,7 +149,10 @@ reg-names = "QuadSPI", "QuadSPI-memory"; interrupts = ; clock-names = "qspi_en", "qspi"; - clocks = <&clockgen 4 0>, <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -156,7 +160,8 @@ compatible = "fsl,ls1012a-esdhc", "fsl,esdhc"; reg = <0x0 0x1560000 0x0 0x10000>; interrupts = <0 62 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; big-endian; @@ -174,7 +179,8 @@ compatible = "fsl,ls1012a-esdhc", "fsl,esdhc"; reg = <0x0 0x1580000 0x0 0x10000>; interrupts = <0 65 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; big-endian; @@ -341,7 +347,8 @@ #size-cells = <0>; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -351,7 +358,8 @@ #size-cells = <0>; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -362,7 +370,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <0 64 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; spi-num-chipselects = <5>; big-endian; status = "disabled"; @@ -372,7 +381,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0500 0x0 0x100>; interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -380,7 +390,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0600 0x0 0x100>; interrupts = <0 54 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -409,7 +420,7 @@ "fsl,imx21-wdt"; reg = <0x0 0x2ad0000 0x0 0x10000>; interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(1)>; big-endian; }; @@ -418,8 +429,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0x2b50000 0x0 0x10000>; interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>, - <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 47>, @@ -432,8 +449,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0x2b60000 0x0 0x10000>; interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>, - <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 45>, @@ -453,8 +476,10 @@ dma-channels = <32>; big-endian; clock-names = "dmamux0", "dmamux1"; - clocks = <&clockgen 4 3>, - <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; }; usb0: usb@2f00000 { @@ -473,7 +498,8 @@ <0x0 0x20140520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; dma-coherent; status = "disabled"; }; From 99314eb13c74b1b7cda73dcc3e779b9a5eb70e48 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:35 +0100 Subject: [PATCH 152/584] arm64: dts: ls1028a: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../fsl-ls1028a-kontron-sl28-var3-ads2.dts | 5 +- .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 162 +++++++++++++----- 2 files changed, 120 insertions(+), 47 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts index c45d7b40e374..ed4e69e87e30 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var3-ads2.dts @@ -8,6 +8,8 @@ */ /dts-v1/; + +#include #include "fsl-ls1028a-kontron-sl28.dts" / { @@ -120,7 +122,8 @@ mclk: clock-mclk@f130080 { compatible = "fsl,vf610-sai-clock"; reg = <0x0 0xf130080 0x0 0x80>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; #clock-cells = <0>; }; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 60ff19fa53b4..401badb713c3 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -8,6 +8,7 @@ * */ +#include #include #include @@ -30,7 +31,7 @@ compatible = "arm,cortex-a72"; reg = <0x0>; enable-method = "psci"; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>; @@ -41,7 +42,7 @@ compatible = "arm,cortex-a72"; reg = <0x1>; enable-method = "psci"; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>; @@ -235,7 +236,8 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -245,7 +247,8 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -255,7 +258,8 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -265,7 +269,8 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -275,7 +280,8 @@ #size-cells = <0>; reg = <0x0 0x2040000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -285,7 +291,8 @@ #size-cells = <0>; reg = <0x0 0x2050000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -295,7 +302,8 @@ #size-cells = <0>; reg = <0x0 0x2060000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -305,7 +313,8 @@ #size-cells = <0>; reg = <0x0 0x2070000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -317,7 +326,8 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = ; - clocks = <&clockgen 2 0>, <&clockgen 2 0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 0>, + <&clockgen QORIQ_CLK_HWACCEL 0>; clock-names = "fspi_en", "fspi"; status = "disabled"; }; @@ -329,7 +339,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = ; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 62>, <&edma0 0 60>; dma-names = "tx", "rx"; spi-num-chipselects = <4>; @@ -344,7 +355,8 @@ reg = <0x0 0x2110000 0x0 0x10000>; interrupts = ; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 58>, <&edma0 0 56>; dma-names = "tx", "rx"; spi-num-chipselects = <4>; @@ -359,7 +371,8 @@ reg = <0x0 0x2120000 0x0 0x10000>; interrupts = ; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 54>, <&edma0 0 2>; dma-names = "tx", "rx"; spi-num-chipselects = <3>; @@ -372,7 +385,7 @@ reg = <0x0 0x2140000 0x0 0x10000>; interrupts = ; clock-frequency = <0>; /* fixed up by bootloader */ - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; little-endian; @@ -385,7 +398,7 @@ reg = <0x0 0x2150000 0x0 0x10000>; interrupts = ; clock-frequency = <0>; /* fixed up by bootloader */ - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; broken-cd; @@ -398,7 +411,8 @@ compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = ; - clocks = <&sysclk>, <&clockgen 4 1>; + clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -407,7 +421,8 @@ compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = ; - clocks = <&sysclk>, <&clockgen 4 1>; + clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -416,7 +431,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0500 0x0 0x100>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -424,7 +440,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0600 0x0 0x100>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -433,7 +450,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2260000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 32>, @@ -445,7 +463,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2270000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 30>, @@ -457,7 +476,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2280000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 28>, @@ -469,7 +489,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2290000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 26>, @@ -481,7 +502,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22a0000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 24>, @@ -493,7 +515,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22b0000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 22>, @@ -512,8 +535,10 @@ interrupt-names = "edma-tx", "edma-err"; dma-channels = <32>; clock-names = "dmamux0", "dmamux1"; - clocks = <&clockgen 4 1>, - <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; }; gpio1: gpio@2300000 { @@ -575,7 +600,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -747,14 +773,20 @@ cluster1_core0_watchdog: watchdog@c000000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core1_watchdog: watchdog@c010000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc010000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; @@ -763,8 +795,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf100000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 4>, @@ -778,8 +816,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf110000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 6>, @@ -793,8 +837,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf120000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 8>, @@ -808,8 +858,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf130000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 10>, @@ -823,8 +879,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf140000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 12>, @@ -838,8 +900,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf150000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 14>, @@ -960,7 +1028,7 @@ ethernet@0,4 { compatible = "fsl,enetc-ptp"; reg = <0x000400 0 0 0 0>; - clocks = <&clockgen 2 3>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 3>; little-endian; fsl,extts-fifo; }; @@ -1055,8 +1123,10 @@ interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 223 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "DE", "SE"; - clocks = <&dpclk>, <&clockgen 2 2>, <&clockgen 2 2>, - <&clockgen 2 2>; + clocks = <&dpclk>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>; clock-names = "pxlclk", "mclk", "aclk", "pclk"; arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; arm,malidp-arqos-value = <0xd000d000>; From 7525022da260eac52e195d70bcd387056a53f8f0 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:36 +0100 Subject: [PATCH 153/584] arm64: dts: ls1043a: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1043a.dtsi | 73 ++++++++++++------- .../boot/dts/freescale/qoriq-fman3-0.dtsi | 6 +- 2 files changed, 52 insertions(+), 27 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi index 12bd1263158f..5a8a1dc4262d 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi @@ -8,6 +8,7 @@ * Mingkai Hu */ +#include #include #include @@ -44,7 +45,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -54,7 +55,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x1>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -64,7 +65,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x2>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -74,7 +75,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x3>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -402,7 +403,10 @@ reg-names = "QuadSPI", "QuadSPI-memory"; interrupts = <0 99 0x4>; clock-names = "qspi_en", "qspi"; - clocks = <&clockgen 4 0>, <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -501,7 +505,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <0 64 0x4>; clock-names = "dspi"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; spi-num-chipselects = <5>; big-endian; status = "disabled"; @@ -514,7 +519,8 @@ reg = <0x0 0x2110000 0x0 0x10000>; interrupts = <0 65 0x4>; clock-names = "dspi"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; spi-num-chipselects = <5>; big-endian; status = "disabled"; @@ -527,7 +533,8 @@ reg = <0x0 0x2180000 0x0 0x10000>; interrupts = <0 56 0x4>; clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; dmas = <&edma0 1 39>, <&edma0 1 38>; dma-names = "tx", "rx"; @@ -541,7 +548,8 @@ reg = <0x0 0x2190000 0x0 0x10000>; interrupts = <0 57 0x4>; clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -552,7 +560,8 @@ reg = <0x0 0x21a0000 0x0 0x10000>; interrupts = <0 58 0x4>; clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -563,7 +572,8 @@ reg = <0x0 0x21b0000 0x0 0x10000>; interrupts = <0 59 0x4>; clock-names = "i2c"; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; status = "disabled"; }; @@ -571,28 +581,32 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0500 0x0 0x100>; interrupts = <0 54 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; }; duart1: serial@21c0600 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0600 0x0 0x100>; interrupts = <0 54 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; }; duart2: serial@21d0500 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21d0500 0x0 0x100>; interrupts = <0 55 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; }; duart3: serial@21d0600 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21d0600 0x0 0x100>; interrupts = <0 55 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; }; gpio1: gpio@2300000 { @@ -704,7 +718,7 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2950000 0x0 0x1000>; interrupts = <0 48 0x4>; - clocks = <&clockgen 0 0>; + clocks = <&clockgen QORIQ_CLK_SYSCLK 0>; clock-names = "ipg"; status = "disabled"; }; @@ -713,7 +727,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2960000 0x0 0x1000>; interrupts = <0 49 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "ipg"; status = "disabled"; }; @@ -722,7 +737,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2970000 0x0 0x1000>; interrupts = <0 50 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "ipg"; status = "disabled"; }; @@ -731,7 +747,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2980000 0x0 0x1000>; interrupts = <0 51 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "ipg"; status = "disabled"; }; @@ -740,7 +757,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2990000 0x0 0x1000>; interrupts = <0 52 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "ipg"; status = "disabled"; }; @@ -749,7 +767,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x29a0000 0x0 0x1000>; interrupts = <0 53 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "ipg"; status = "disabled"; }; @@ -758,7 +777,8 @@ compatible = "fsl,ls1043a-wdt", "fsl,imx21-wdt"; reg = <0x0 0x2ad0000 0x0 0x10000>; interrupts = <0 83 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "wdog"; big-endian; }; @@ -775,8 +795,10 @@ dma-channels = <32>; big-endian; clock-names = "dmamux0", "dmamux1"; - clocks = <&clockgen 4 0>, - <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; }; usb0: usb@2f00000 { @@ -818,7 +840,8 @@ <0x0 0x20140520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = <0 69 0x4>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; dma-coherent; }; diff --git a/arch/arm64/boot/dts/freescale/qoriq-fman3-0.dtsi b/arch/arm64/boot/dts/freescale/qoriq-fman3-0.dtsi index 4338db14c5da..ae1c2abaaf36 100644 --- a/arch/arm64/boot/dts/freescale/qoriq-fman3-0.dtsi +++ b/arch/arm64/boot/dts/freescale/qoriq-fman3-0.dtsi @@ -6,6 +6,8 @@ * */ +#include + fman0: fman@1a00000 { #address-cells = <1>; #size-cells = <1>; @@ -15,7 +17,7 @@ fman0: fman@1a00000 { reg = <0x0 0x1a00000 0x0 0xfe000>; interrupts = , ; - clocks = <&clockgen 3 0>; + clocks = <&clockgen QORIQ_CLK_FMAN 0>; clock-names = "fmanclk"; fsl,qman-channel-range = <0x800 0x10>; ptimer-handle = <&ptp_timer0>; @@ -81,6 +83,6 @@ ptp_timer0: ptp-timer@1afe000 { compatible = "fsl,fman-ptp-timer"; reg = <0x0 0x1afe000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 3 0>; + clocks = <&clockgen QORIQ_CLK_FMAN 0>; fsl,extts-fifo; }; From 973fb5e174b0d4c27d479abe1c632730c91e80cf Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:37 +0100 Subject: [PATCH 154/584] arm64: dts: ls1046a: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1046a.dtsi | 73 ++++++++++++------- 1 file changed, 48 insertions(+), 25 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi index d3f5e48c58dd..f581a6d1f881 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi @@ -8,6 +8,7 @@ * Mingkai Hu */ +#include #include #include @@ -39,7 +40,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -49,7 +50,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x1>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -59,7 +60,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x2>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -69,7 +70,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x3>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; @@ -295,7 +296,10 @@ reg-names = "QuadSPI", "QuadSPI-memory"; interrupts = ; clock-names = "qspi_en", "qspi"; - clocks = <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -303,7 +307,7 @@ compatible = "fsl,ls1046a-esdhc", "fsl,esdhc"; reg = <0x0 0x1560000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; big-endian; @@ -479,7 +483,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = ; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; spi-num-chipselects = <5>; big-endian; status = "disabled"; @@ -491,7 +496,8 @@ #size-cells = <0>; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 1 39>, <&edma0 1 38>; dma-names = "tx", "rx"; @@ -504,7 +510,8 @@ #size-cells = <0>; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -514,7 +521,8 @@ #size-cells = <0>; reg = <0x0 0x21a0000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -524,7 +532,8 @@ #size-cells = <0>; reg = <0x0 0x21b0000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -532,7 +541,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0500 0x0 0x100>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -540,7 +550,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0600 0x0 0x100>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -548,7 +559,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21d0500 0x0 0x100>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -556,7 +568,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21d0600 0x0 0x100>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; }; @@ -604,7 +617,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2950000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; clock-names = "ipg"; status = "disabled"; }; @@ -613,7 +627,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2960000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; status = "disabled"; }; @@ -622,7 +637,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2970000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; status = "disabled"; }; @@ -631,7 +647,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2980000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; status = "disabled"; }; @@ -640,7 +657,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x2990000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; status = "disabled"; }; @@ -649,7 +667,8 @@ compatible = "fsl,ls1021a-lpuart"; reg = <0x0 0x29a0000 0x0 0x1000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; status = "disabled"; }; @@ -658,7 +677,8 @@ compatible = "fsl,imx21-wdt"; reg = <0x0 0x2ad0000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; big-endian; }; @@ -674,8 +694,10 @@ dma-channels = <32>; big-endian; clock-names = "dmamux0", "dmamux1"; - clocks = <&clockgen 4 1>, - <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; }; usb0: usb@2f00000 { @@ -714,7 +736,8 @@ <0x0 0x20140520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = ; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; }; msi1: msi-controller@1580000 { From f9799323bda63d6d2e398caa413c0b242e311f83 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:38 +0100 Subject: [PATCH 155/584] arm64: dts: ls1088a: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1088a.dtsi | 91 +++++++++++++------ 1 file changed, 64 insertions(+), 27 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi index ee0354928f6b..8ffbc9fde041 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi @@ -7,6 +7,7 @@ * Harninder Rai * */ +#include #include #include @@ -30,7 +31,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -39,7 +40,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x1>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -48,7 +49,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x2>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -57,7 +58,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x3>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -66,7 +67,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x100>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -75,7 +76,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x101>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -84,7 +85,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x102>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -93,7 +94,7 @@ device_type = "cpu"; compatible = "arm,cortex-a53"; reg = <0x103>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PH20>; #cooling-cells = <2>; }; @@ -310,7 +311,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = ; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; spi-num-chipselects = <6>; status = "disabled"; }; @@ -318,7 +320,8 @@ duart0: serial@21c0500 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0500 0x0 0x100>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -326,7 +329,8 @@ duart1: serial@21c0600 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0600 0x0 0x100>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; @@ -391,7 +395,8 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; status = "disabled"; }; @@ -401,7 +406,8 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; status = "disabled"; }; @@ -411,7 +417,8 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; status = "disabled"; }; @@ -421,7 +428,8 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; status = "disabled"; }; @@ -434,7 +442,10 @@ reg-names = "QuadSPI", "QuadSPI-memory"; interrupts = ; clock-names = "qspi_en", "qspi"; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; }; @@ -443,7 +454,7 @@ reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <0 28 0x4>; /* Level high type */ clock-frequency = <0>; - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; little-endian; @@ -478,7 +489,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = <0 133 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; status = "disabled"; }; @@ -729,7 +741,8 @@ ptp-timer@8b95000 { compatible = "fsl,dpaa2-ptp"; reg = <0x0 0x8b95000 0x0 0x100>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(1)>; little-endian; fsl,extts-fifo; }; @@ -818,56 +831,80 @@ cluster1_core0_watchdog: wdt@c000000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core1_watchdog: wdt@c010000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc010000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core2_watchdog: wdt@c020000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc020000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core3_watchdog: wdt@c030000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc030000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster2_core0_watchdog: wdt@c100000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc100000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster2_core1_watchdog: wdt@c110000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc110000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster2_core2_watchdog: wdt@c120000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc120000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster2_core3_watchdog: wdt@c130000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc130000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; From b0ccb208d76019362fd97d5463b848e1a6b2132d Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:39 +0100 Subject: [PATCH 156/584] arm64: dts: ls208xa: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls2080a.dtsi | 17 ++-- .../arm64/boot/dts/freescale/fsl-ls2088a.dtsi | 17 ++-- .../arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 85 ++++++++++++++----- 3 files changed, 81 insertions(+), 38 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi index f9c1d30cf4a7..76ab68d2de0b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi @@ -9,6 +9,7 @@ * */ +#include #include "fsl-ls208xa.dtsi" &cpu { @@ -16,7 +17,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster0_l2>; #cooling-cells = <2>; @@ -26,7 +27,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x1>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster0_l2>; #cooling-cells = <2>; @@ -36,7 +37,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x100>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster1_l2>; #cooling-cells = <2>; @@ -46,7 +47,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x101>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster1_l2>; #cooling-cells = <2>; @@ -56,7 +57,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x200>; - clocks = <&clockgen 1 2>; + clocks = <&clockgen QORIQ_CLK_CMUX 2>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster2_l2>; #cooling-cells = <2>; @@ -66,7 +67,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x201>; - clocks = <&clockgen 1 2>; + clocks = <&clockgen QORIQ_CLK_CMUX 2>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster2_l2>; #cooling-cells = <2>; @@ -76,7 +77,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x300>; - clocks = <&clockgen 1 3>; + clocks = <&clockgen QORIQ_CLK_CMUX 3>; next-level-cache = <&cluster3_l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>; @@ -86,7 +87,7 @@ device_type = "cpu"; compatible = "arm,cortex-a57"; reg = <0x301>; - clocks = <&clockgen 1 3>; + clocks = <&clockgen QORIQ_CLK_CMUX 3>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster3_l2>; #cooling-cells = <2>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi index a5f668d786b8..da24dc127698 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls2088a.dtsi @@ -9,6 +9,7 @@ * */ +#include #include "fsl-ls208xa.dtsi" &cpu { @@ -16,7 +17,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster0_l2>; #cooling-cells = <2>; @@ -26,7 +27,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x1>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster0_l2>; #cooling-cells = <2>; @@ -36,7 +37,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x100>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster1_l2>; #cooling-cells = <2>; @@ -46,7 +47,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x101>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster1_l2>; #cooling-cells = <2>; @@ -56,7 +57,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x200>; - clocks = <&clockgen 1 2>; + clocks = <&clockgen QORIQ_CLK_CMUX 2>; next-level-cache = <&cluster2_l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>; @@ -66,7 +67,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x201>; - clocks = <&clockgen 1 2>; + clocks = <&clockgen QORIQ_CLK_CMUX 2>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster2_l2>; #cooling-cells = <2>; @@ -76,7 +77,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x300>; - clocks = <&clockgen 1 3>; + clocks = <&clockgen QORIQ_CLK_CMUX 3>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster3_l2>; #cooling-cells = <2>; @@ -86,7 +87,7 @@ device_type = "cpu"; compatible = "arm,cortex-a72"; reg = <0x301>; - clocks = <&clockgen 1 3>; + clocks = <&clockgen QORIQ_CLK_CMUX 3>; cpu-idle-states = <&CPU_PW20>; next-level-cache = <&cluster3_l2>; #cooling-cells = <2>; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi index 767e3710bff2..135ac8210871 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi @@ -9,6 +9,7 @@ * */ +#include #include #include @@ -356,84 +357,112 @@ serial0: serial@21c0500 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0500 0x0 0x100>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; interrupts = <0 32 0x4>; /* Level high type */ }; serial1: serial@21c0600 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21c0600 0x0 0x100>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; interrupts = <0 32 0x4>; /* Level high type */ }; serial2: serial@21d0500 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21d0500 0x0 0x100>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; interrupts = <0 33 0x4>; /* Level high type */ }; serial3: serial@21d0600 { compatible = "fsl,ns16550", "ns16550a"; reg = <0x0 0x21d0600 0x0 0x100>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; interrupts = <0 33 0x4>; /* Level high type */ }; cluster1_core0_watchdog: wdt@c000000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core1_watchdog: wdt@c010000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc010000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster2_core0_watchdog: wdt@c100000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc100000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster2_core1_watchdog: wdt@c110000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc110000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster3_core0_watchdog: wdt@c200000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc200000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster3_core1_watchdog: wdt@c210000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc210000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster4_core0_watchdog: wdt@c300000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc300000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster4_core1_watchdog: wdt@c310000 { compatible = "arm,sp805-wdt", "arm,primecell"; reg = <0x0 0xc310000 0x0 0x1000>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "wdog_clk", "apb_pclk"; }; @@ -484,7 +513,8 @@ ptp-timer@8b95000 { compatible = "fsl,dpaa2-ptp"; reg = <0x0 0x8b95000 0x0 0x100>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; little-endian; fsl,extts-fifo; }; @@ -895,7 +925,8 @@ #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <0 26 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "dspi"; spi-num-chipselects = <5>; bus-num = <0>; @@ -906,7 +937,8 @@ compatible = "fsl,ls2080a-esdhc", "fsl,esdhc"; reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <0 28 0x4>; /* Level high type */ - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; little-endian; @@ -965,7 +997,8 @@ reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <0 34 0x4>; /* Level high type */ clock-names = "i2c"; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; }; i2c1: i2c@2010000 { @@ -976,7 +1009,8 @@ reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <0 34 0x4>; /* Level high type */ clock-names = "i2c"; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; }; i2c2: i2c@2020000 { @@ -987,7 +1021,8 @@ reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <0 35 0x4>; /* Level high type */ clock-names = "i2c"; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; }; i2c3: i2c@2030000 { @@ -998,7 +1033,8 @@ reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <0 35 0x4>; /* Level high type */ clock-names = "i2c"; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; }; ifc: ifc@2240000 { @@ -1022,7 +1058,10 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "QuadSPI", "QuadSPI-memory"; interrupts = ; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "qspi_en", "qspi"; status = "disabled"; }; @@ -1120,7 +1159,8 @@ compatible = "fsl,ls2080a-ahci"; reg = <0x0 0x3200000 0x0 0x10000>; interrupts = <0 133 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; }; @@ -1129,7 +1169,8 @@ compatible = "fsl,ls2080a-ahci"; reg = <0x0 0x3210000 0x0 0x10000>; interrupts = <0 136 0x4>; /* Level high type */ - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; }; From 8e9f7797bcdfc95586bd9722e1944b1609d93fa6 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 12:47:40 +0100 Subject: [PATCH 157/584] arm64: dts: lx2160a: use constants in the clockgen phandle Now that we have constants, use them. This is just a mechanical change. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 92 ++++++++++++------- 1 file changed, 57 insertions(+), 35 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi index 0d4bce13b8f1..451e4430024c 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi @@ -4,6 +4,7 @@ // // Copyright 2018-2020 NXP +#include #include #include #include @@ -30,7 +31,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x0>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -47,7 +48,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x1>; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -64,7 +65,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x100>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -81,7 +82,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x101>; - clocks = <&clockgen 1 1>; + clocks = <&clockgen QORIQ_CLK_CMUX 1>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -98,7 +99,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x200>; - clocks = <&clockgen 1 2>; + clocks = <&clockgen QORIQ_CLK_CMUX 2>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -115,7 +116,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x201>; - clocks = <&clockgen 1 2>; + clocks = <&clockgen QORIQ_CLK_CMUX 2>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -132,7 +133,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x300>; - clocks = <&clockgen 1 3>; + clocks = <&clockgen QORIQ_CLK_CMUX 3>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -149,7 +150,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x301>; - clocks = <&clockgen 1 3>; + clocks = <&clockgen QORIQ_CLK_CMUX 3>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -166,7 +167,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x400>; - clocks = <&clockgen 1 4>; + clocks = <&clockgen QORIQ_CLK_CMUX 4>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -183,7 +184,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x401>; - clocks = <&clockgen 1 4>; + clocks = <&clockgen QORIQ_CLK_CMUX 4>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -200,7 +201,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x500>; - clocks = <&clockgen 1 5>; + clocks = <&clockgen QORIQ_CLK_CMUX 5>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -217,7 +218,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x501>; - clocks = <&clockgen 1 5>; + clocks = <&clockgen QORIQ_CLK_CMUX 5>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -234,7 +235,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x600>; - clocks = <&clockgen 1 6>; + clocks = <&clockgen QORIQ_CLK_CMUX 6>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -251,7 +252,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x601>; - clocks = <&clockgen 1 6>; + clocks = <&clockgen QORIQ_CLK_CMUX 6>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -268,7 +269,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x700>; - clocks = <&clockgen 1 7>; + clocks = <&clockgen QORIQ_CLK_CMUX 7>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -285,7 +286,7 @@ compatible = "arm,cortex-a72"; enable-method = "psci"; reg = <0x701>; - clocks = <&clockgen 1 7>; + clocks = <&clockgen QORIQ_CLK_CMUX 7>; d-cache-size = <0x8000>; d-cache-line-size = <64>; d-cache-sets = <128>; @@ -716,7 +717,8 @@ reg = <0x0 0x2000000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; scl-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>; status = "disabled"; }; @@ -728,7 +730,8 @@ reg = <0x0 0x2010000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; status = "disabled"; }; @@ -739,7 +742,8 @@ reg = <0x0 0x2020000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; status = "disabled"; }; @@ -750,7 +754,8 @@ reg = <0x0 0x2030000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; status = "disabled"; }; @@ -761,7 +766,8 @@ reg = <0x0 0x2040000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; scl-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>; status = "disabled"; }; @@ -773,7 +779,8 @@ reg = <0x0 0x2050000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; status = "disabled"; }; @@ -784,7 +791,8 @@ reg = <0x0 0x2060000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; status = "disabled"; }; @@ -795,7 +803,8 @@ reg = <0x0 0x2070000 0x0 0x10000>; interrupts = ; clock-names = "i2c"; - clocks = <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; status = "disabled"; }; @@ -807,7 +816,10 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = ; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; clock-names = "fspi_en", "fspi"; status = "disabled"; }; @@ -818,7 +830,8 @@ #size-cells = <0>; reg = <0x0 0x2100000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; clock-names = "dspi"; spi-num-chipselects = <5>; bus-num = <0>; @@ -831,7 +844,8 @@ #size-cells = <0>; reg = <0x0 0x2110000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; clock-names = "dspi"; spi-num-chipselects = <5>; bus-num = <1>; @@ -844,7 +858,8 @@ #size-cells = <0>; reg = <0x0 0x2120000 0x0 0x10000>; interrupts = ; - clocks = <&clockgen 4 7>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>; clock-names = "dspi"; spi-num-chipselects = <5>; bus-num = <2>; @@ -855,7 +870,8 @@ compatible = "fsl,esdhc"; reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <0 28 0x4>; /* Level high type */ - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dma-coherent; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; @@ -868,7 +884,8 @@ compatible = "fsl,esdhc"; reg = <0x0 0x2150000 0x0 0x10000>; interrupts = <0 63 0x4>; /* Level high type */ - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dma-coherent; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; @@ -1004,7 +1021,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; status = "disabled"; }; @@ -1015,7 +1033,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; status = "disabled"; }; @@ -1026,7 +1045,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; status = "disabled"; }; @@ -1037,7 +1057,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = ; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; dma-coherent; status = "disabled"; }; @@ -1310,7 +1331,8 @@ ptp-timer@8b95000 { compatible = "fsl,dpaa2-ptp"; reg = <0x0 0x8b95000 0x0 0x100>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; little-endian; fsl,extts-fifo; }; From 267d46714054bcffe0925adc90043712795156d5 Mon Sep 17 00:00:00 2001 From: Alice Guo Date: Mon, 4 Jan 2021 17:15:41 +0800 Subject: [PATCH 158/584] dt-bindings: soc: imx8m: add DT Binding doc for soc unique ID Add DT Binding doc for the Unique ID of i.MX 8M series. Reviewed-by: Krzysztof Kozlowski Reviewed-by: Rob Herring Signed-off-by: Alice Guo Signed-off-by: Shawn Guo --- .../bindings/soc/imx/imx8m-soc.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/soc/imx/imx8m-soc.yaml diff --git a/Documentation/devicetree/bindings/soc/imx/imx8m-soc.yaml b/Documentation/devicetree/bindings/soc/imx/imx8m-soc.yaml new file mode 100644 index 000000000000..effcc72f9425 --- /dev/null +++ b/Documentation/devicetree/bindings/soc/imx/imx8m-soc.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soc/imx/imx8m-soc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NXP i.MX8M Series SoC + +maintainers: + - Alice Guo + +description: | + NXP i.MX8M series SoCs contain fuse entries from which SoC Unique ID can be + obtained. + +select: + properties: + compatible: + contains: + enum: + - fsl,imx8mm + - fsl,imx8mn + - fsl,imx8mp + - fsl,imx8mq + required: + - compatible + +patternProperties: + "^soc@[0-9a-f]+$": + type: object + properties: + compatible: + items: + - enum: + - fsl,imx8mm-soc + - fsl,imx8mn-soc + - fsl,imx8mp-soc + - fsl,imx8mq-soc + - const: simple-bus + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + ranges: true + + dma-ranges: true + + nvmem-cells: + maxItems: 1 + description: Phandle to the SOC Unique ID provided by a nvmem node + + nvmem-cell-names: + const: soc_unique_id + + required: + - compatible + - nvmem-cells + - nvmem-cell-names + + additionalProperties: + type: object + +additionalProperties: true + +examples: + - | + / { + model = "FSL i.MX8MM EVK board"; + compatible = "fsl,imx8mm-evk", "fsl,imx8mm"; + #address-cells = <2>; + #size-cells = <2>; + + soc@0 { + compatible = "fsl,imx8mm-soc", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x0 0x3e000000>; + nvmem-cells = <&imx8mm_uid>; + nvmem-cell-names = "soc_unique_id"; + }; + }; + +... From ce58459d8c7f4174e7b8a8ea903dd949631334a3 Mon Sep 17 00:00:00 2001 From: Alice Guo Date: Mon, 4 Jan 2021 17:15:42 +0800 Subject: [PATCH 159/584] arm64: dts: imx8m: add SoC ID compatible Add compatible string to .dtsi files for binding of imx8_soc_info and device. Reviewed-by: Krzysztof Kozlowski Signed-off-by: Alice Guo Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm.dtsi | 2 +- arch/arm64/boot/dts/freescale/imx8mn.dtsi | 2 +- arch/arm64/boot/dts/freescale/imx8mp.dtsi | 2 +- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index c824f2615fe8..d457ce815e68 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -257,7 +257,7 @@ }; soc@0 { - compatible = "simple-bus"; + compatible = "fsl,imx8mm-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index 00808bb40680..e96fd9a24e0e 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -241,7 +241,7 @@ }; soc@0 { - compatible = "simple-bus"; + compatible = "fsl,imx8mn-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index ecccfbb4f5ad..ec6ac523ecfc 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -218,7 +218,7 @@ }; soc@0 { - compatible = "simple-bus"; + compatible = "fsl,imx8mp-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 50ae17f65a51..64398599591b 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -286,7 +286,7 @@ }; soc@0 { - compatible = "simple-bus"; + compatible = "fsl,imx8mq-soc", "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; From cbff23797fa1ec00e3bdda57d8472f75c0b7aab9 Mon Sep 17 00:00:00 2001 From: Alice Guo Date: Mon, 4 Jan 2021 17:15:43 +0800 Subject: [PATCH 160/584] arm64: dts: imx8m: add NVMEM provider and consumer to read soc unique ID In order to be able to use NVMEM APIs to read soc unique ID, add the nvmem data cell and name for nvmem-cells to the "soc" node, and add a nvmem node which provides soc unique ID to efuse@30350000. Reviewed-by: Krzysztof Kozlowski Signed-off-by: Alice Guo Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm.dtsi | 6 ++++++ arch/arm64/boot/dts/freescale/imx8mn.dtsi | 6 ++++++ arch/arm64/boot/dts/freescale/imx8mp.dtsi | 6 ++++++ arch/arm64/boot/dts/freescale/imx8mq.dtsi | 6 ++++++ 4 files changed, 24 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index d457ce815e68..9bee6f1889a4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -261,6 +261,8 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; + nvmem-cells = <&imx8mm_uid>; + nvmem-cell-names = "soc_unique_id"; aips1: bus@30000000 { compatible = "fsl,aips-bus", "simple-bus"; @@ -518,6 +520,10 @@ #address-cells = <1>; #size-cells = <1>; + imx8mm_uid: unique-id@410 { + reg = <0x4 0x8>; + }; + cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index e96fd9a24e0e..d021aba5fb1f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -245,6 +245,8 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; + nvmem-cells = <&imx8mn_uid>; + nvmem-cell-names = "soc_unique_id"; aips1: bus@30000000 { compatible = "fsl,aips-bus", "simple-bus"; @@ -531,6 +533,10 @@ #address-cells = <1>; #size-cells = <1>; + imx8mn_uid: unique-id@410 { + reg = <0x4 0x8>; + }; + cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index ec6ac523ecfc..9401e92f1c84 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -222,6 +222,8 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; + nvmem-cells = <&imx8mp_uid>; + nvmem-cell-names = "soc_unique_id"; aips1: bus@30000000 { compatible = "fsl,aips-bus", "simple-bus"; @@ -328,6 +330,10 @@ #address-cells = <1>; #size-cells = <1>; + imx8mp_uid: unique-id@420 { + reg = <0x8 0x8>; + }; + cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 64398599591b..9fcb001b8dde 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -291,6 +291,8 @@ #size-cells = <1>; ranges = <0x0 0x0 0x0 0x3e000000>; dma-ranges = <0x40000000 0x0 0x40000000 0xc0000000>; + nvmem-cells = <&imx8mq_uid>; + nvmem-cell-names = "soc_unique_id"; bus@30000000 { /* AIPS1 */ compatible = "fsl,aips-bus", "simple-bus"; @@ -555,6 +557,10 @@ #address-cells = <1>; #size-cells = <1>; + imx8mq_uid: soc-uid@410 { + reg = <0x4 0x8>; + }; + cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; From 46a7867dd704d1700d0e7491f71892becce8b654 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Mon, 4 Jan 2021 09:36:46 -0800 Subject: [PATCH 161/584] dt-bindings: arm: fsl: Add binding for Gateworks boards with IMX8MM Add bindings for the Gateworks Venice Development kit boards with IMX8MM System on Module. Signed-off-by: Tim Harvey Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 51b8d6fac792..c4a81884a8af 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -674,6 +674,9 @@ properties: - beacon,imx8mm-beacon-kit # i.MX8MM Beacon Development Kit - fsl,imx8mm-ddr4-evk # i.MX8MM DDR4 EVK Board - fsl,imx8mm-evk # i.MX8MM EVK Board + - gw,imx8mm-gw71xx-0x # i.MX8MM Gateworks Development Kit + - gw,imx8mm-gw72xx-0x # i.MX8MM Gateworks Development Kit + - gw,imx8mm-gw73xx-0x # i.MX8MM Gateworks Development Kit - kontron,imx8mm-n801x-som # i.MX8MM Kontron SL (N801X) SOM - variscite,var-som-mx8mm # i.MX8MM Variscite VAR-SOM-MX8MM module - const: fsl,imx8mm From 6f30b27c5ef54a266d188ffbee3bacfdd40e8f73 Mon Sep 17 00:00:00 2001 From: Tim Harvey Date: Mon, 4 Jan 2021 09:36:47 -0800 Subject: [PATCH 162/584] arm64: dts: imx8mm: Add Gateworks i.MX 8M Mini Development Kits The Gateworks Venice GW71xx-0x/GW72xx-0x/GW73xx-0x are development kits consisting of a GW700x SoM and a Baseboard. Future SoM's such as the GW701x will create additional combinations. The GW700x SoM contains: - i.MX 8M Mini SoC - LPDDR4 DRAM - eMMC FLASH - Gateworks System Controller (eeprom/pushbutton/reset/voltage-monitor) - GbE PHY connected to the i.MX 8M Mini FEC - Power Management IC The GW71xx Baseboard contains: - 1x MiniPCIe Socket with USB2.0, PCIe, and SIM - 1x RJ45 GbE (i.MX 8M Mini FEC) - I/O connector with 1x-SPI/1x-I2C/1x-UART/4x-GPIO signals - PCIe Clock generator - GPS and accelerometer - 1x USB 2.0 Front Panel connector - wide range power supply The GW72xx Baseboard contains: - 2x MiniPCIe Socket with USB2.0, PCIe, and SIM - 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x) - 1x MicroSD connector - 1x USB 2.0 Front Panel connector - 1x SPI connector - 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of: RS232 w/ flow-control, RS485, RS422 - PCIe Clock generator - GPS and accelerometer - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) - I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C - wide range power supply The GW73xx Baseboard contains: - 3x MiniPCIe Socket with USB2.0, PCIe, and SIM - 2x RJ45 GbE (i.MX 8M Mini FEC and LAN743x) - 1x MicroSD connector - 1x USB 2.0 Front Panel connector - 1x SPI connector - 1x Serial connector supporting 2x-UART or 1x-UART configured as 1 of: RS232 w/ flow-control, RS485, RS422 - WiFi/BT - PCIe Clock generator - GPS and accelerometer - Media Expansion connector (MIPI-CSI/MIPI-DSI/GPIO/I2S) - I/O connector with 2x-ADC,2x-GPIO,1x-UART,1x-I2C - wide range power supply Signed-off-by: Tim Harvey Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/Makefile | 3 + .../dts/freescale/imx8mm-venice-gw700x.dtsi | 495 ++++++++++++++++++ .../dts/freescale/imx8mm-venice-gw71xx-0x.dts | 19 + .../dts/freescale/imx8mm-venice-gw71xx.dtsi | 186 +++++++ .../dts/freescale/imx8mm-venice-gw72xx-0x.dts | 20 + .../dts/freescale/imx8mm-venice-gw72xx.dtsi | 311 +++++++++++ .../dts/freescale/imx8mm-venice-gw73xx-0x.dts | 19 + .../dts/freescale/imx8mm-venice-gw73xx.dtsi | 362 +++++++++++++ 8 files changed, 1415 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 901d80086b47..6f76026a2c3c 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -34,6 +34,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi new file mode 100644 index 000000000000..c769fadbd008 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi @@ -0,0 +1,495 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +#include +#include +#include + +/ { + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + user-pb { + label = "user_pb"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + user-pb1x { + label = "user_pb1x"; + linux,code = ; + interrupt-parent = <&gsc>; + interrupts = <0>; + }; + + key-erased { + label = "key_erased"; + linux,code = ; + interrupt-parent = <&gsc>; + interrupts = <1>; + }; + + eeprom-wp { + label = "eeprom_wp"; + linux,code = ; + interrupt-parent = <&gsc>; + interrupts = <2>; + }; + + tamper { + label = "tamper"; + linux,code = ; + interrupt-parent = <&gsc>; + interrupts = <5>; + }; + + switch-hold { + label = "switch_hold"; + linux,code = ; + interrupt-parent = <&gsc>; + interrupts = <7>; + }; + }; +}; + +&A53_0 { + cpu-supply = <&buck3_reg>; +}; + +&A53_1 { + cpu-supply = <&buck3_reg>; +}; + +&A53_2 { + cpu-supply = <&buck3_reg>; +}; + +&A53_3 { + cpu-supply = <&buck3_reg>; +}; + +&ddrc { + operating-points-v2 = <&ddrc_opp_table>; + + ddrc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-25M { + opp-hz = /bits/ 64 <25000000>; + }; + + opp-100M { + opp-hz = /bits/ 64 <100000000>; + }; + + opp-750M { + opp-hz = /bits/ 64 <750000000>; + }; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + tx-fifo-depth = ; + rx-fifo-depth = ; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + gsc: gsc@20 { + compatible = "gw,gsc"; + reg = <0x20>; + pinctrl-0 = <&pinctrl_gsc>; + interrupt-parent = <&gpio2>; + interrupts = <6 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + adc { + compatible = "gw,gsc-adc"; + #address-cells = <1>; + #size-cells = <0>; + + channel@6 { + gw,mode = <0>; + reg = <0x06>; + label = "temp"; + }; + + channel@8 { + gw,mode = <1>; + reg = <0x08>; + label = "vdd_bat"; + }; + + channel@16 { + gw,mode = <4>; + reg = <0x16>; + label = "fan_tach"; + }; + + channel@82 { + gw,mode = <2>; + reg = <0x82>; + label = "vdd_vin"; + gw,voltage-divider-ohms = <22100 1000>; + }; + + channel@84 { + gw,mode = <2>; + reg = <0x84>; + label = "vdd_adc1"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@86 { + gw,mode = <2>; + reg = <0x86>; + label = "vdd_adc2"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@88 { + gw,mode = <2>; + reg = <0x88>; + label = "vdd_dram"; + }; + + channel@8c { + gw,mode = <2>; + reg = <0x8c>; + label = "vdd_1p2"; + }; + + channel@8e { + gw,mode = <2>; + reg = <0x8e>; + label = "vdd_1p0"; + }; + + channel@90 { + gw,mode = <2>; + reg = <0x90>; + label = "vdd_2p5"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@92 { + gw,mode = <2>; + reg = <0x92>; + label = "vdd_3p3"; + gw,voltage-divider-ohms = <10000 10000>; + }; + + channel@98 { + gw,mode = <2>; + reg = <0x98>; + label = "vdd_0p95"; + }; + + channel@9a { + gw,mode = <2>; + reg = <0x9a>; + label = "vdd_1p8"; + }; + + channel@a2 { + gw,mode = <2>; + reg = <0xa2>; + label = "vdd_gsc"; + gw,voltage-divider-ohms = <10000 10000>; + }; + }; + + fan-controller@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "gw,gsc-fan"; + reg = <0x0a>; + }; + }; + + gpio: gpio@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&gsc>; + interrupts = <4>; + }; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + rtc@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; + + pmic@69 { + compatible = "mps,mp5416"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + reg = <0x69>; + + regulators { + buck1 { + regulator-name = "vdd_0p95"; + regulator-min-microvolt = <805000>; + regulator-max-microvolt = <1000000>; + regulator-max-microamp = <2500000>; + regulator-boot-on; + }; + + buck2 { + regulator-name = "vdd_soc"; + regulator-min-microvolt = <805000>; + regulator-max-microvolt = <900000>; + regulator-max-microamp = <1000000>; + regulator-boot-on; + }; + + buck3_reg: buck3 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <805000>; + regulator-max-microvolt = <1000000>; + regulator-max-microamp = <2200000>; + regulator-boot-on; + }; + + buck4 { + regulator-name = "vdd_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-max-microamp = <500000>; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "nvcc_snvs_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-max-microamp = <300000>; + regulator-boot-on; + }; + + ldo2 { + regulator-name = "vdd_snvs_0p8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-boot-on; + }; + + ldo3 { + regulator-name = "vdd_0p95"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-boot-on; + }; + + ldo4 { + regulator-name = "vdd_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + eeprom@52 { + compatible = "atmel,24c32"; + reg = <0x52>; + pagesize = <32>; + }; +}; + +/* console */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0 0x19 + >; + }; + + pinctrl_gsc: gscgrp { + fsl,pins = < + MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x159 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL 0x400001c3 + MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 + MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 + MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 + MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 + MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts new file mode 100644 index 000000000000..3f88c4ad5716 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx-0x.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/dts-v1/; + +#include "imx8mm.dtsi" +#include "imx8mm-venice-gw700x.dtsi" +#include "imx8mm-venice-gw71xx.dtsi" + +/ { + model = "Gateworks Venice GW71xx-0x i.MX8MM Development Kit"; + compatible = "gw,imx8mm-gw71xx-0x", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi new file mode 100644 index 000000000000..905b68a3daa5 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi @@ -0,0 +1,186 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +#include +#include + +/ { + aliases { + usb0 = &usbotg1; + usb1 = &usbotg2; + }; + + led-controller { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led-0 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pps { + compatible = "pps-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +/* off-board header */ +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + accelerometer@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +/* off-board header */ +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +/* GPS */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* off-board header */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ + MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3 0x40000041 /* DIO2 */ + MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4 0x40000041 /* DIO2 */ + >; + }; + + pinctrl_accel: accelgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 + >; + }; + + pinctrl_gpio_leds: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pps: ppsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 + >; + }; + + pinctrl_reg_usb1_en: regusb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 + >; + }; + + pinctrl_spi2: spi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts new file mode 100644 index 000000000000..b1e7540f0281 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/dts-v1/; + +#include "imx8mm.dtsi" +#include "imx8mm-venice-gw700x.dtsi" +#include "imx8mm-venice-gw72xx.dtsi" + +/ { + model = "Gateworks Venice GW72xx-0x i.MX8MM Development Kit"; + compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; + diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi new file mode 100644 index 000000000000..b7c91bdc21dd --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi @@ -0,0 +1,311 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +#include +#include + +/ { + aliases { + usb0 = &usbotg1; + usb1 = &usbotg2; + }; + + led-controller { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led-0 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pps { + compatible = "pps-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg2_vbus: regulator-usb-otg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb2_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg2_vbus"; + gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; +}; + +/* off-board header */ +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + accelerometer@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +/* off-board header */ +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +/* off-board header */ +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +/* GPS */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* off-board header */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +/* RS232 */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + vbus-supply = <®_usb_otg2_vbus>; + status = "okay"; +}; + +/* microSD */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x40000104 /* RS485_TERM */ + MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /* RS485 */ + MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x40000104 /* RS485_HALF */ + >; + }; + + pinctrl_accel: accelgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 + >; + }; + + pinctrl_gpio_leds: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pps: ppsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 + >; + }; + + pinctrl_reg_usb1_en: regusb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 + >; + }; + + pinctrl_reg_usb2_en: regusb2grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41 + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + + pinctrl_spi2: spi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + MX8MM_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts new file mode 100644 index 000000000000..6905437ff281 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +/dts-v1/; + +#include "imx8mm.dtsi" +#include "imx8mm-venice-gw700x.dtsi" +#include "imx8mm-venice-gw73xx.dtsi" + +/ { + model = "Gateworks Venice GW73xx-0x i.MX8MM Development Kit"; + compatible = "gw,imx8mm-gw73xx-0x", "fsl,imx8mm"; + + chosen { + stdout-path = &uart2; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi new file mode 100644 index 000000000000..d2ffd62a3bd4 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi @@ -0,0 +1,362 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2020 Gateworks Corporation + */ + +#include +#include + +/ { + aliases { + usb0 = &usbotg1; + usb1 = &usbotg2; + }; + + led-controller { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led-0 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pps { + compatible = "pps-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pps>; + gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>; + status = "okay"; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg1_vbus: regulator-usb-otg1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb1_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_usb_otg2_vbus: regulator-usb-otg2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usb2_en>; + compatible = "regulator-fixed"; + regulator-name = "usb_otg2_vbus"; + gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_wifi_en: regulator-wifi-en { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_wl>; + compatible = "regulator-fixed"; + regulator-name = "wl"; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + startup-delay-us = <100>; + enable-active-high; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; +}; + +/* off-board header */ +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + accelerometer@19 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_accel>; + compatible = "st,lis2de12"; + reg = <0x19>; + st,drdy-int-pin = <1>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "INT1"; + }; +}; + +/* off-board header */ +&i2c3 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +/* off-board header */ +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + assigned-clocks = <&clk IMX8MM_CLK_SAI3>; + assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>; + assigned-clock-rates = <24576000>; + status = "okay"; +}; + +/* GPS */ +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +/* bluetooth HCI */ +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_bten>; + cts-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; + rts-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + shutdown-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; +}; + +/* RS232 */ +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "otg"; + vbus-supply = <®_usb_otg1_vbus>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + vbus-supply = <®_usb_otg2_vbus>; + status = "okay"; +}; + +/* SDIO WiFi */ +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + bus-width = <4>; + non-removable; + vmmc-supply = <®_wifi_en>; + status = "okay"; +}; + +/* microSD */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3 0x40000041 /* PLUG_TEST */ + MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6 0x40000041 /* PCI_USBSEL */ + MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7 0x40000041 /* PCIE_WDIS# */ + MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7 0x40000041 /* DIO0 */ + MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x40000041 /* DIO1 */ + MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0 0x40000104 /* RS485_TERM */ + MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0 0x40000104 /* RS485 */ + MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2 0x40000104 /* RS485_HALF */ + >; + }; + + pinctrl_accel: accelgrp { + fsl,pins = < + MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5 0x159 + >; + }; + + pinctrl_bten: btengrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x41 + >; + }; + + pinctrl_gpio_leds: gpioledgrp { + fsl,pins = < + MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5 0x19 + MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4 0x19 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_pps: ppsgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 + >; + }; + + pinctrl_reg_wl: regwlgrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5 0x41 + >; + }; + + pinctrl_reg_usb1_en: regusb1grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12 0x41 + MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x41 + >; + }; + + pinctrl_reg_usb2_en: regusb2grp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41 + >; + }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK 0xd6 + MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0 0xd6 + >; + }; + + pinctrl_spi2: spi2grp { + fsl,pins = < + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0xd6 + MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0xd6 + MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0xd6 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 + MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX 0x140 + MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX 0x140 + MX8MM_IOMUXC_ECSPI1_MISO_GPIO5_IO8 0x140 + MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x140 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX 0x140 + MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + MX8MM_IOMUXC_SD2_RESET_B_USDHC2_RESET_B 0x1d0 + MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0x1d0 + >; + }; +}; From 002c73209e9dfbfb8ba997610e1f63e2e62335e2 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Wed, 6 Jan 2021 10:04:13 +0100 Subject: [PATCH 163/584] dt-bindings: arm: fsl: add Protonic MVT board Add Protonic MVT imx6dl based board Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index c4a81884a8af..c39840f0f3aa 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -367,6 +367,7 @@ properties: - ply,plybas # Plymovent BAS board - ply,plym2m # Plymovent M2M board - poslab,imx6dl-savageboard # Poslab SavageBoard Dual + - prt,prtmvt # Protonic MVT board - prt,prtrvt # Protonic RVT board - prt,prtvt7 # Protonic VT7 board - rex,imx6dl-rex-basic # Rex Basic i.MX6 Dual Lite Board From f3604ba14bd75e081707b8107dd9420bfa573e0c Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Wed, 6 Jan 2021 10:04:14 +0100 Subject: [PATCH 164/584] ARM: dts: add Protonic MVT board PRTMVT is the reference platform for Protonic industrial touchscreen terminals. Signed-off-by: Oleksij Rempel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-prtmvt.dts | 852 ++++++++++++++++++++++++++++ 2 files changed, 853 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-prtmvt.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 0756c41106fd..90a715b3900a 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -467,6 +467,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-pico-pi.dtb \ imx6dl-plybas.dtb \ imx6dl-plym2m.dtb \ + imx6dl-prtmvt.dtb \ imx6dl-prtrvt.dtb \ imx6dl-prtvt7.dtb \ imx6dl-rex-basic.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-prtmvt.dts b/arch/arm/boot/dts/imx6dl-prtmvt.dts new file mode 100644 index 000000000000..a35a1c66e770 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-prtmvt.dts @@ -0,0 +1,852 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2016 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel , Pengutronix + */ + +/dts-v1/; +#include +#include +#include +#include +#include +#include +#include "imx6dl.dtsi" + +/ { + model = "Protonic MVT board"; + compatible = "prt,prtmvt", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight>; + pwms = <&pwm1 0 5000000 0>; + brightness-levels = <0 16 64 255>; + num-interpolated-steps = <16>; + default-brightness-level = <1>; + power-supply = <®_3v3>; + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + }; + + connector { + compatible = "composite-video-connector"; + label = "Composite0"; + sdtv-standards = ; + + port { + comp0_out: endpoint { + remote-endpoint = <&tvp5150_comp0_in>; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpiokeys>; + autorepeat; + + power { + label = "Power Button"; + gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + linux,code = ; + wakeup-source; + }; + + f1 { + label = "GPIO Key F1"; + linux,code = ; + gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>; + }; + + f2 { + label = "GPIO Key F2"; + linux,code = ; + gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>; + }; + + f3 { + label = "GPIO Key F3"; + linux,code = ; + gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>; + }; + + f4 { + label = "GPIO Key F4"; + linux,code = ; + gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>; + }; + + f5 { + label = "GPIO Key F5"; + linux,code = ; + gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>; + }; + + cycle { + label = "GPIO Key CYCLE"; + linux,code = ; + gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>; + }; + + esc { + label = "GPIO Key ESC"; + linux,code = ; + gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>; + }; + + up { + label = "GPIO Key UP"; + linux,code = ; + gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>; + }; + + down { + label = "GPIO Key DOWN"; + linux,code = ; + gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>; + }; + + ok { + label = "GPIO Key OK"; + linux,code = ; + gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>; + }; + + f6 { + label = "GPIO Key F6"; + linux,code = ; + gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>; + }; + + f7 { + label = "GPIO Key F7"; + linux,code = ; + gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>; + }; + + f8 { + label = "GPIO Key F8"; + linux,code = ; + gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>; + }; + + f9 { + label = "GPIO Key F9"; + linux,code = ; + gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>; + }; + + f10 { + label = "GPIO Key F10"; + linux,code = ; + gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>; + }; + + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "debug0"; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "debug1"; + function = LED_FUNCTION_DISK; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "disk-activity"; + }; + + led-2 { + label = "power_led"; + function = LED_FUNCTION_POWER; + gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + panel { + compatible = "kyo,tcg070wvlq", "lg,lb070wv8"; + backlight = <&backlight>; + power-supply = <®_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + clk50m_phy: phy-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_h1_vbus: regulator-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "h1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_otg_vbus: regulator-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "otg-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "prti6q-sgtl5000"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Line", "Line In Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "External Speaker", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&ssi1>; + system-clock-frequency = <0>; + }; + + simple-audio-card,codec { + sound-dai = <&codec>; + bitclock-master; + frame-master; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; + + mux-ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN 0 + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TFSDIR 0 + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) + >; + }; + + mux-pins3 { + fsl,audmux-port = <2>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) + 0 IMX_AUDMUX_V2_PDCR_TXRXEN + >; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clk50m_phy>; + clock-names = "ipg", "ahb", "ptp"; + phy-handle = <&rmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <3000>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR", + "CAM2_MIRROR", "", "", "SMBALERT", + "DEBUG_0", "DEBUG_1", "", "", "", "", "", "", + "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK", + "SD1_DATA3", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4", + "BOARD_ID0", "BOARD_ID1", "BOARD_ID2", + "", "", "", "", "", "", "", "ON_SWITCH", + "POWER_LED", "", "", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1", + "CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ", + "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0", + "YACO_RESET"; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX", + "", "", "DIP1_FB", "", "", "", "", "", + "CPU_LIGHT_ON", "", "ETH_RESET", "", "BL_EN", + "BL_PWM", "ETH_INTRP", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX", + "YACO_AUX_TX", "ITU656_D0", "ITU656_D1"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: audio-codec@a { + compatible = "fsl,sgtl5000"; + reg = <0xa>; + #sound-dai-cells = <0>; + clocks = <&clks 201>; + VDDA-supply = <®_3v3>; + VDDIO-supply = <®_3v3>; + VDDD-supply = <®_1v8>; + }; + + video@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tvp5150_comp0_in: endpoint { + remote-endpoint = <&comp0_out>; + }; + }; + + /* Output port 2 is video output pad */ + port@2 { + reg = <2>; + tvp5151_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + }; + }; + }; + + gpio_pca: gpio@74 { + compatible = "nxp,pca9539"; + reg = <0x74>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pca9539>; + interrupt-parent = <&gpio4>; + interrupts = <5 IRQ_TYPE_LEVEL_LOW>; + gpio-controller; + #gpio-cells = <2>; + }; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + adc@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@5 { + reg = <5>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@6 { + reg = <6>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@7 { + reg = <7>; + ti,gain = <3>; + ti,datarate = <3>; + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&ipu1_csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_csi0>; + status = "okay"; +}; + +&ipu1_csi0_mux_from_parallel_sensor { + remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&ssi1 { + #sound-dai-cells = <0>; + fsl,mode = "ac97-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_h1_vbus>; + pinctrl-names = "default"; + phy_type = "utmi"; + dr_mode = "host"; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_backlight: backlightgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000 + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008 + /* CAN2_SR */ + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0 + >; + }; + + pinctrl_gpiokeys: gpiokeygrp { + fsl,pins = < + /* nON_SWITCH */ + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0 + >; + }; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* ITU656_nRESET */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 + /* CAM1_MIRROR */ + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0 + /* CAM2_MIRROR */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0 + /* CAM_nDETECT */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + /* ISB_IN1 */ + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0 + /* ISB_nIN2 */ + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 + /* WARN_LIGHT */ + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0 + /* ON2_FB */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 + /* YACO_nIRQ */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 + /* YACO_BOOT0 */ + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 + /* YACO_nRESET */ + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 + /* FORCE_ON1 */ + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + /* AUDIO_nRESET */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 + /* ITU656_nPDN */ + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 + + /* HW revision detect */ + /* REV_ID0 */ + MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 + /* REV_ID1 */ + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 + /* REV_ID2 */ + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 + /* REV_ID3 */ + MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 + /* REV_ID4 */ + MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 + + /* New in HW revision 1 */ + /* ON1_FB */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 + /* DIP1_FB */ + MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_csi0: ipu1csi0grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + /* DEBUG0 */ + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0 + /* DEBUG1 */ + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0 + /* POWER_LED */ + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0 + >; + }; + + pinctrl_pca9539: pca9539 { + fsl,pins = < + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + >; + }; + + /* YaCO AUX Uart */ + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + /* YaCO Touchscreen UART */ + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; +}; From 2e0e77e4b82c8ae12a8a835fe84eac2e14b993eb Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Wed, 6 Jan 2021 17:08:51 +0200 Subject: [PATCH 165/584] ARM: dts: imx6q(dl): Move 'port' nodes under 'ports' for HDMI encoder In preparation for the conversion of the DWC HDMI TX device tree bindings to YAML, move the HDMI encoder's 'port' nodes under a 'ports' node. The 'ports' node is optional in the OF graph implementation, but YAML bindings require it. Signed-off-by: Laurent Pinchart Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6q.dtsi | 20 +++++++++++--------- arch/arm/boot/dts/imx6qdl.dtsi | 25 ++++++++++++++----------- 2 files changed, 25 insertions(+), 20 deletions(-) diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 5277e3903291..8d209c1b3ca7 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -406,19 +406,21 @@ &hdmi { compatible = "fsl,imx6q-hdmi"; - port@2 { - reg = <2>; + ports { + port@2 { + reg = <2>; - hdmi_mux_2: endpoint { - remote-endpoint = <&ipu2_di0_hdmi>; + hdmi_mux_2: endpoint { + remote-endpoint = <&ipu2_di0_hdmi>; + }; }; - }; - port@3 { - reg = <3>; + port@3 { + reg = <3>; - hdmi_mux_3: endpoint { - remote-endpoint = <&ipu2_di1_hdmi>; + hdmi_mux_3: endpoint { + remote-endpoint = <&ipu2_di1_hdmi>; + }; }; }; }; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 6f59a99cbe82..82e01ce026ea 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -182,8 +182,6 @@ }; hdmi: hdmi@120000 { - #address-cells = <1>; - #size-cells = <0>; reg = <0x00120000 0x9000>; interrupts = <0 115 0x04>; gpr = <&gpr>; @@ -192,19 +190,24 @@ clock-names = "iahb", "isfr"; status = "disabled"; - port@0 { - reg = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; - hdmi_mux_0: endpoint { - remote-endpoint = <&ipu1_di0_hdmi>; + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; }; - }; - port@1 { - reg = <1>; + port@1 { + reg = <1>; - hdmi_mux_1: endpoint { - remote-endpoint = <&ipu1_di1_hdmi>; + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; }; }; }; From 60f95bf61edda3abfc5b01f1093e98ebc87439f4 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Thu, 7 Jan 2021 09:52:32 +0100 Subject: [PATCH 166/584] dt-bindings: arm: fsl: add Protonic PRTI6G board Add Protonic Holland PRTI6G, iMX6UL based board Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index c39840f0f3aa..b99137c80a5a 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -491,6 +491,7 @@ properties: - karo,imx6ul-tx6ul # Ka-Ro electronics TXUL-0010 Module - kontron,imx6ul-n6310-som # Kontron N6310 SOM - kontron,imx6ul-n6311-som # Kontron N6311 SOM + - prt,prti6g # Protonic PRTI6G Board - technexion,imx6ul-pico-dwarf # TechNexion i.MX6UL Pico-Dwarf - technexion,imx6ul-pico-hobbit # TechNexion i.MX6UL Pico-Hobbit - technexion,imx6ul-pico-pi # TechNexion i.MX6UL Pico-Pi From 062bf67d83e5a814a7d523d5d9e46a8fc75764b1 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Thu, 7 Jan 2021 09:52:33 +0100 Subject: [PATCH 167/584] ARM: dts: add Protonic PRTI6G board Protonic PRTI6G is a reference platform for industrial, safety critical applications Signed-off-by: Oleksij Rempel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6ul-prti6g.dts | 356 ++++++++++++++++++++++++++++ 2 files changed, 357 insertions(+) create mode 100644 arch/arm/boot/dts/imx6ul-prti6g.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 90a715b3900a..8b422215df4b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -634,6 +634,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \ imx6ul-pico-pi.dtb \ imx6ul-phytec-segin-ff-rdk-emmc.dtb \ imx6ul-phytec-segin-ff-rdk-nand.dtb \ + imx6ul-prti6g.dtb \ imx6ul-tx6ul-0010.dtb \ imx6ul-tx6ul-0011.dtb \ imx6ul-tx6ul-mainboard.dtb \ diff --git a/arch/arm/boot/dts/imx6ul-prti6g.dts b/arch/arm/boot/dts/imx6ul-prti6g.dts new file mode 100644 index 000000000000..d62015701d0a --- /dev/null +++ b/arch/arm/boot/dts/imx6ul-prti6g.dts @@ -0,0 +1,356 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2016 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel , Pengutronix + */ + +/dts-v1/; +#include "imx6ul.dtsi" +#include + +/ { + model = "Protonic PRTI6G Board"; + compatible = "prt,prti6g", "fsl,imx6ul"; + + chosen { + stdout-path = &uart1; + }; + + clock_ksz8081_in: clock-ksz8081-in { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + + clock_ksz8081_out: clock-ksz8081-out { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "debug0"; + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + + reg_3v2: regulator-3v2 { + compatible = "regulator-fixed"; + regulator-name = "3v2"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&ecspi1 { + cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <1000000>; + }; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eth1>; + phy-mode = "rmii"; + phy-handle = <&rmii_phy>; + clocks = <&clks IMX6UL_CLK_ENET>, + <&clks IMX6UL_CLK_ENET_AHB>, + <&clks IMX6UL_CLK_ENET_PTP>, + <&clock_ksz8081_out>; + clock-names = "ipg", "ahb", "ptp", + "enet_clk_ref"; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + clocks = <&clock_ksz8081_in>; + clock-names = "rmii-ref"; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <100000>; + status = "okay"; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "okay"; + + adc@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@5 { + reg = <5>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@6 { + reg = <6>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@7 { + reg = <7>; + ti,gain = <3>; + ti,datarate = <3>; + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usbotg1 { + dr_mode = "host"; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_3v2>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_can1: can1grp { + fsl,pins = < + MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x0b0b0 + MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x0b0b0 + /* SR */ + MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x0b0b0 + /* TERM */ + MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x0b0b0 + /* nSMBALERT */ + MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x0b0b0 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x0b0b0 + MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x0b0b0 + /* SR */ + MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x0b0b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x0b0b0 + MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x000b1 + MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x0b0b0 + MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x0b0b0 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x0b0b0 + MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x000b1 + MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x0b0b0 + MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x0b0b0 + >; + }; + + pinctrl_eth1: eth1grp { + fsl,pins = < + MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0 + MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x100b0 + MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0 + MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0 + MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x100b0 + MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0 + MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0 + MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0 + MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x1b000 + /* PHY ENET1_RST */ + MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x00880 + /* PHY ENET1_IRQ */ + MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x00880 + >; + }; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* HW revision detect */ + /* REV_ID0 */ + MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08 0x1b0b0 + /* REV_ID1 */ + MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09 0x1b0b0 + /* REV_ID2 */ + MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10 0x1b0b0 + /* REV_ID3 */ + MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11 0x1b0b0 + /* BOARD_ID0 */ + MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13 0x1b0b0 + /* BOARD_ID1 */ + MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14 0x1b0b0 + /* BOARD_ID2 */ + MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15 0x1b0b0 + /* BOARD_ID3 */ + MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12 0x1b0b0 + /* Safety controller IO */ + /* WAKE_SC */ + MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 + /* PROGRAM_SC */ + MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0 + MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6UL_PAD_CSI_VSYNC__I2C2_SDA 0x4001b8b0 + MX6UL_PAD_CSI_HSYNC__I2C2_SCL 0x4001b8b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + MX6UL_PAD_NAND_DQS__GPIO4_IO16 0x1b0b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1 + MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x070b1 + MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x07099 + MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x070b1 + MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x070b1 + MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x070b1 + MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x070b1 + /* SD1 CD */ + MX6UL_PAD_NAND_READY_B__GPIO4_IO12 0x170b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9 + MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9 + MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9 + MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9 + MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9 + MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9 + MX6UL_PAD_NAND_DATA04__USDHC2_DATA4 0x170f9 + MX6UL_PAD_NAND_DATA05__USDHC2_DATA5 0x170f9 + MX6UL_PAD_NAND_DATA06__USDHC2_DATA6 0x170f9 + MX6UL_PAD_NAND_DATA07__USDHC2_DATA7 0x170f9 + MX6UL_PAD_NAND_ALE__USDHC2_RESET_B 0x170b0 + >; + }; +}; From d22782c03d896da9dc2f4df45ba1620912ec9e17 Mon Sep 17 00:00:00 2001 From: Teresa Remmet Date: Thu, 7 Jan 2021 10:12:10 +0100 Subject: [PATCH 168/584] bindings: arm: fsl: Add PHYTEC i.MX8MP devicetree bindings Add devicetree bindings for i.MX8MP based phyCORE-i.MX8MP and phyBOARD-Pollux RDK. Signed-off-by: Teresa Remmet Reviewed-by: Krzysztof Kozlowski Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index b99137c80a5a..2ae66407e2aa 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -715,6 +715,12 @@ properties: - fsl,imx8mp-evk # i.MX8MP EVK Board - const: fsl,imx8mp + - description: PHYTEC phyCORE-i.MX8MP SoM based boards + items: + - const: phytec,imx8mp-phyboard-pollux-rdk # phyBOARD-Pollux RDK + - const: phytec,imx8mp-phycore-som # phyCORE-i.MX8MP SoM + - const: fsl,imx8mp + - description: i.MX8MQ based Boards items: - enum: From 88f7f6bcca371b71ba93ff9c170c7c87927654df Mon Sep 17 00:00:00 2001 From: Teresa Remmet Date: Thu, 7 Jan 2021 10:12:11 +0100 Subject: [PATCH 169/584] arm64: dts: freescale: Add support for phyBOARD-Pollux-i.MX8MP Add initial support for phyBOARD-Pollux-i.MX8MP. Supported basic features: * eMMC * i2c EEPROM * i2c RTC * i2c LED * PMIC * debug UART * SD card * 1Gbit Ethernet (fec) * watchdog Signed-off-by: Teresa Remmet Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../freescale/imx8mp-phyboard-pollux-rdk.dts | 161 ++++++++++ .../dts/freescale/imx8mp-phycore-som.dtsi | 293 ++++++++++++++++++ 3 files changed, 455 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 6f76026a2c3c..38559943c15d 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -42,6 +42,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts new file mode 100644 index 000000000000..0e1a6d953389 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts @@ -0,0 +1,161 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 PHYTEC Messtechnik GmbH + * Author: Teresa Remmet + */ + +/dts-v1/; + +#include +#include +#include "imx8mp-phycore-som.dtsi" + +/ { + model = "PHYTEC phyBOARD-Pollux i.MX8MP"; + compatible = "phytec,imx8mp-phyboard-pollux-rdk", + "phytec,imx8mp-phycore-som", "fsl,imx8mp"; + + chosen { + stdout-path = &uart2; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <100>; + off-on-delay-us = <12000>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + pinctrl-1 = <&pinctrl_i2c2_gpio>; + sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + leds@62 { + compatible = "nxp,pca9533"; + reg = <0x62>; + + led1 { + type = ; + }; + + led2 { + type = ; + }; + + led3 { + type = ; + }; + }; +}; + +&snvs_pwrkey { + status = "okay"; +}; + +/* debug console */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +/* SD-Card */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_pins>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_pins>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_pins>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + vmmc-supply = <®_usdhc2_vmmc>; + bus-width = <4>; + status = "okay"; +}; + +&iomuxc { + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c3 + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c3 + >; + }; + + pinctrl_i2c2_gpio: i2c2gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16 0x1e3 + MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17 0x1e3 + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x41 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x49 + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x49 + >; + }; + + pinctrl_usdhc2_pins: usdhc2-gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi new file mode 100644 index 000000000000..44a8c2337cee --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi @@ -0,0 +1,293 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2020 PHYTEC Messtechnik GmbH + * Author: Teresa Remmet + */ + +#include +#include "imx8mp.dtsi" + +/ { + model = "PHYTEC phyCORE-i.MX8MP"; + compatible = "phytec,imx8mp-phycore-som", "fsl,imx8mp"; + + aliases { + rtc0 = &rv3028; + rtc1 = &snvs_rtc; + }; + + memory@40000000 { + device_type = "memory"; + reg = <0x0 0x40000000 0 0x80000000>; + }; +}; + +&A53_0 { + cpu-supply = <&buck2>; +}; + +&A53_1 { + cpu-supply = <&buck2>; +}; + +&A53_2 { + cpu-supply = <&buck2>; +}; + +&A53_3 { + cpu-supply = <&buck2>; +}; + +/* ethernet 1 */ +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy1>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0>; + interrupt-parent = <&gpio1>; + interrupts = <15 IRQ_TYPE_EDGE_FALLING>; + ti,rx-internal-delay = ; + ti,tx-internal-delay = ; + ti,fifo-depth = ; + ti,clk-output-sel = ; + enet-phy-lane-no-swap; + }; + }; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + pmic: pmic@25 { + reg = <0x25>; + compatible = "nxp,pca9450c"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupt-parent = <&gpio4>; + interrupts = <18 IRQ_TYPE_LEVEL_LOW>; + + regulators { + buck1: BUCK1 { + regulator-compatible = "BUCK1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck2: BUCK2 { + regulator-compatible = "BUCK2"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + buck4: BUCK4 { + regulator-compatible = "BUCK4"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck5: BUCK5 { + regulator-compatible = "BUCK5"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + buck6: BUCK6 { + regulator-compatible = "BUCK6"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1: LDO1 { + regulator-compatible = "LDO1"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2: LDO2 { + regulator-compatible = "LDO2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1150000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3: LDO3 { + regulator-compatible = "LDO3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4: LDO4 { + regulator-compatible = "LDO4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo5: LDO5 { + regulator-compatible = "LDO5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + }; + }; + + eeprom@51 { + compatible = "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + }; + + rv3028: rtc@52 { + compatible = "microcrystal,rv3028"; + reg = <0x52>; + trickle-resistor-ohms = <3000>; + }; +}; + +/* eMMC */ +&usdhc3 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_fec: fecgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC 0x3 + MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO 0x3 + MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0 0x91 + MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1 0x91 + MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2 0x91 + MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3 0x91 + MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC 0x91 + MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0 0x1f + MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1 0x1f + MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2 0x1f + MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3 0x1f + MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC 0x1f + MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15 0x11 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c3 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c1_gpio: i2c1gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14 0x1e3 + MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15 0x1e3 + >; + }; + + pinctrl_pmic: pmicirqgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18 0x141 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + >; + }; +}; From fe82bb4db5339ebe8175b0ff2d45757472c0415e Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:04:54 -0600 Subject: [PATCH 170/584] arm64: dts: renesas: beacon: Configure programmable clocks When the board was added, clock drivers were being updated done at the same time to allow the versaclock driver to properly configure the modes. Unfortunately, the updates were not applied to the board files at the time they should have been, so do it now. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-1-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- .../dts/renesas/beacon-renesom-baseboard.dtsi | 27 ++++++++++++++++++- .../boot/dts/renesas/beacon-renesom-som.dtsi | 26 ++++++++++++++++++ 2 files changed, 52 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index 9db120ccb58d..c788f294cb09 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -5,6 +5,7 @@ #include #include +#include / { backlight_lvds: backlight-lvds { @@ -370,12 +371,36 @@ #clock-cells = <1>; clocks = <&x304_clk>; clock-names = "xin"; - /* CSI0_MCLK, CSI1_MCLK, AUDIO_CLKIN, USB_HUB_MCLK_BB */ + assigned-clocks = <&versaclock6_bb 1>, <&versaclock6_bb 2>, <&versaclock6_bb 3>, <&versaclock6_bb 4>; assigned-clock-rates = <24000000>, <24000000>, <24000000>, <24576000>; + + OUT1 { + idt,mode = ; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT2 { + idt,mode = ; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT3 { + idt,mode = ; + idt,voltage-microvolt = <3300000>; + idt,slew-percent = <100>; + }; + + OUT4 { + idt,mode = ; + idt,voltage-microvolt = <3300000>; + idt,slew-percent = <100>; + }; }; }; diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index b475de38ace8..6e74c391860c 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -4,6 +4,7 @@ */ #include +#include / { memory@48000000 { @@ -170,7 +171,32 @@ <&versaclock5 2>, <&versaclock5 3>, <&versaclock5 4>; + assigned-clock-rates = <33333333>, <33333333>, <50000000>, <125000000>; + + OUT1 { + idt,mode = ; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT2 { + idt,mode = ; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT3 { + idt,mode = ; + idt,voltage-microvolt = <1800000>; + idt,slew-percent = <100>; + }; + + OUT4 { + idt,mode = ; + idt,voltage-microvolt = <3300000>; + idt,slew-percent = <100>; + }; }; }; From b29120d6cfa978ae0721af855afbae3137c8e66d Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:04:55 -0600 Subject: [PATCH 171/584] arm64: dts: renesas: beacon kit: Fix Audio Clock sources The SoC was expecting two clock sources with different frequencies. One to support 44.1KHz and one to support 48KHz. With the newly added ability to configure the programmable clock, configure both clocks. Assign the rcar-sound clocks to reference the versaclock instead of the fixed clock. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-2-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- .../dts/renesas/beacon-renesom-baseboard.dtsi | 25 +------------------ .../dts/renesas/r8a774a1-beacon-rzg2m-kit.dts | 21 ++++++++++++++++ 2 files changed, 22 insertions(+), 24 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index c788f294cb09..e66e302bdccb 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -246,12 +246,6 @@ }; }; -&audio_clk_a { - clock-frequency = <24576000>; - assigned-clocks = <&versaclock6_bb 4>; - assigned-clock-rates = <24576000>; -}; - &audio_clk_b { clock-frequency = <22579200>; }; @@ -596,7 +590,7 @@ }; sound_clk_pins: sound_clk { - groups = "audio_clk_a_a"; + groups = "audio_clk_a_a", "audio_clk_b_a"; function = "audio_clk"; }; @@ -647,23 +641,6 @@ status = "okay"; - clocks = <&cpg CPG_MOD 1005>, - <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, - <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, - <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, - <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, - <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, - <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, - <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, - <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, - <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, - <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, - <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, - <&audio_clk_a>, <&audio_clk_b>, <&audio_clk_c>, - <&cpg CPG_CORE R8A774A1_CLK_S0D4>; - ports { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts index 2c5b057c30c6..25eeac411f12 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts +++ b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts @@ -27,3 +27,24 @@ stdout-path = "serial0:115200n8"; }; }; + +/* Reference versaclock instead of audio_clk_a */ +&rcar_sound { + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&versaclock6_bb 4>, <&audio_clk_b>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A774A1_CLK_S0D4>; +}; From dc3dba98d2d31420a263b726e5c0a25aa7122e85 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:04:56 -0600 Subject: [PATCH 172/584] arm64: dts: renesas: beacon: Configure Audio CODEC clocks With the newly added configurable clock options, the audio CODEC can configure the mclk automatically. Add the reference to the versaclock. Since the devices on I2C5 can communicate at 400KHz, let's also increase that too Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-3-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index e66e302bdccb..b31a28239fcb 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -408,13 +408,14 @@ &i2c5 { status = "okay"; - clock-frequency = <100000>; + clock-frequency = <400000>; pinctrl-0 = <&i2c5_pins>; pinctrl-names = "default"; codec: wm8962@1a { compatible = "wlf,wm8962"; reg = <0x1a>; + clocks = <&versaclock6_bb 3>; DCVDD-supply = <®_audio>; DBVDD-supply = <®_audio>; AVDD-supply = <®_audio>; From e718d563750db293e84f826be9e7ab49d8e4b97e Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:04:57 -0600 Subject: [PATCH 173/584] arm64: dts: renesas: beacon: Better describe keys The keys on the baseboard are laid out in an diamond pattern, up, down, left, right and center. Update the descriptions to make it easier to read. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-4-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- .../dts/renesas/beacon-renesom-baseboard.dtsi | 30 +++++++++---------- 1 file changed, 15 insertions(+), 15 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index b31a28239fcb..ae0f58eb2be8 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -40,38 +40,38 @@ keys { compatible = "gpio-keys"; - key-1 { + key-1 { /* S19 */ gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "Switch-1"; + linux,code = ; + label = "Up"; wakeup-source; debounce-interval = <20>; }; - key-2 { + key-2 { /*S20 */ gpios = <&gpio3 13 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "Switch-2"; + linux,code = ; + label = "Left"; wakeup-source; debounce-interval = <20>; }; - key-3 { + key-3 { /* S21 */ gpios = <&gpio5 17 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "Switch-3"; + linux,code = ; + label = "Down"; wakeup-source; debounce-interval = <20>; }; - key-4 { + key-4 { /* S22 */ gpios = <&gpio5 20 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "Switch-4"; + linux,code = ; + label = "Right"; wakeup-source; debounce-interval = <20>; }; - key-5 { + key-5 { /* S23 */ gpios = <&gpio5 22 GPIO_ACTIVE_LOW>; - linux,code = ; - label = "Switch-4"; + linux,code = ; + label = "Center"; wakeup-source; debounce-interval = <20>; }; From 33aaab6d5c634784ecf5612e7ac11346adac8d6b Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:04:59 -0600 Subject: [PATCH 174/584] arm64: dts: renesas: beacon-rzg2m-kit: Rearrange SoC unique functions In preparation for adding new dev kits, move anything specific to the RZ/G2M from the SOM-level and baseboard-levels and move them to the kit-level. This allows the SOM and baseboard to be reused with other SoC's. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-6-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- .../dts/renesas/beacon-renesom-baseboard.dtsi | 15 -------------- .../boot/dts/renesas/beacon-renesom-som.dtsi | 5 ----- .../dts/renesas/r8a774a1-beacon-rzg2m-kit.dts | 20 +++++++++++++++++++ 3 files changed, 20 insertions(+), 20 deletions(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi index ae0f58eb2be8..30c169b08536 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi @@ -264,21 +264,6 @@ status = "okay"; }; -&du { - pinctrl-0 = <&du_pins>; - pinctrl-names = "default"; - status = "okay"; - - clocks = <&cpg CPG_MOD 724>, - <&cpg CPG_MOD 723>, - <&cpg CPG_MOD 722>, - <&versaclock5 1>, - <&x302_clk>, - <&versaclock5 2>; - clock-names = "du.0", "du.1", "du.2", - "dclkin.0", "dclkin.1", "dclkin.2"; -}; - &du_out_rgb { remote-endpoint = <&rgb_panel>; }; diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index 6e74c391860c..f4201e1c2226 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -13,11 +13,6 @@ reg = <0x0 0x48000000 0x0 0x78000000>; }; - memory@600000000 { - device_type = "memory"; - reg = <0x6 0x00000000 0x0 0x80000000>; - }; - osc_32k: osc_32k { compatible = "fixed-clock"; #clock-cells = <0>; diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts index 25eeac411f12..501cb05da228 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts +++ b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts @@ -26,6 +26,26 @@ chosen { stdout-path = "serial0:115200n8"; }; + + memory@600000000 { + device_type = "memory"; + reg = <0x6 0x00000000 0x0 0x80000000>; + }; +}; + +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 722>, + <&versaclock5 1>, + <&x302_clk>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.2", + "dclkin.0", "dclkin.1", "dclkin.2"; }; /* Reference versaclock instead of audio_clk_a */ From ed6ae131b0e88260d593fb3f02561de25ffc1045 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:05:00 -0600 Subject: [PATCH 175/584] arm64: dts: renesas: r8a774b1: Introduce beacon-rzg2n-kit Beacon EmbeddedWorks is introducing a new kit based on the RZ/G2N SoC from Renesas. The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1 cellular radio. The Baseboard has Ethernet, USB, HDMI, stereo audio in and out, along with a variety of push buttons and LED's, and support for a parallel RGB and an LVDS display. It uses the same baseboard and SOM as the RZ/G2M. This SOM has only 2GB of DDR, and beacon-renesom-som.dtsi contains the base memory node, so an additional memory node isn't necessary. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-7-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/Makefile | 1 + .../dts/renesas/r8a774b1-beacon-rzg2n-kit.dts | 66 +++++++++++++++++++ 2 files changed, 67 insertions(+) create mode 100644 arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile index 3b8b03705917..ea3d7d9bc52e 100644 --- a/arch/arm64/boot/dts/renesas/Makefile +++ b/arch/arm64/boot/dts/renesas/Makefile @@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-rev2.dtb dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-rev2-ex.dtb dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-rev2-ex-idk-1110wr.dtb +dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-beacon-rzg2n-kit.dtb dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-hihope-rzg2n.dtb dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-hihope-rzg2n-ex.dtb dtb-$(CONFIG_ARCH_R8A774B1) += r8a774b1-hihope-rzg2n-ex-idk-1110wr.dtb diff --git a/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts new file mode 100644 index 000000000000..71763f4402a7 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts @@ -0,0 +1,66 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2020, Compass Electronics Group, LLC + */ + +/dts-v1/; + +#include "r8a774b1.dtsi" +#include "beacon-renesom-som.dtsi" +#include "beacon-renesom-baseboard.dtsi" + +/ { + model = "Beacon Embedded Works RZ/G2N Development Kit"; + compatible = "beacon,beacon-rzg2n", "renesas,r8a774b1"; + + aliases { + serial0 = &scif2; + serial1 = &hscif0; + serial2 = &hscif1; + serial3 = &scif0; + serial4 = &hscif2; + serial5 = &scif5; + serial6 = &scif4; + ethernet0 = &avb; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 721>, + <&versaclock5 1>, + <&x302_clk>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.3", + "dclkin.0", "dclkin.1", "dclkin.3"; +}; + +/* Reference versaclock instead of audio_clk_a */ +&rcar_sound { + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&versaclock6_bb 4>, <&audio_clk_b>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A774B1_CLK_S0D4>; +}; From 4d0e87eb6f54422418a2d985433866535856b6bd Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Thu, 24 Dec 2020 11:05:01 -0600 Subject: [PATCH 176/584] arm64: dts: renesas: r8a774e1: Introduce beacon-rzg2h-kit Beacon EmbeddedWorks is introducing a new kit based on the RZ/G2H SoC from Renesas. The SOM supports eMMC, WiFi and Bluetooth, along with a Cat-M1 cellular radio. The Baseboard has Ethernet, USB, HDMI, stereo audio in and out, along with a variety of push buttons and LED's, and support for a parallel RGB and an LVDS display. It uses the same baseboard and SOM files as the RZ/G2M and RZ/G2N kits. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201224170502.2254683-8-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/Makefile | 1 + .../dts/renesas/r8a774e1-beacon-rzg2h-kit.dts | 71 +++++++++++++++++++ 2 files changed, 72 insertions(+) create mode 100644 arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile index ea3d7d9bc52e..f2de2fa0c8b8 100644 --- a/arch/arm64/boot/dts/renesas/Makefile +++ b/arch/arm64/boot/dts/renesas/Makefile @@ -22,6 +22,7 @@ dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-ek874.dtb dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-ek874-idk-2121wr.dtb dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-ek874-mipi-2.1.dtb +dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-beacon-rzg2h-kit.dtb dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-hihope-rzg2h.dtb dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-hihope-rzg2h-ex.dtb dtb-$(CONFIG_ARCH_R8A774E1) += r8a774e1-hihope-rzg2h-ex-idk-1110wr.dtb diff --git a/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts new file mode 100644 index 000000000000..273f062f2909 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts @@ -0,0 +1,71 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright 2020, Compass Electronics Group, LLC + */ + +/dts-v1/; + +#include "r8a774e1.dtsi" +#include "beacon-renesom-som.dtsi" +#include "beacon-renesom-baseboard.dtsi" + +/ { + model = "Beacon Embedded Works RZ/G2H Development Kit"; + compatible = "beacon,beacon-rzg2h", "renesas,r8a774e1"; + + aliases { + serial0 = &scif2; + serial1 = &hscif0; + serial2 = &hscif1; + serial3 = &scif0; + serial4 = &hscif2; + serial5 = &scif5; + serial6 = &scif4; + ethernet0 = &avb; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@500000000 { + device_type = "memory"; + reg = <0x5 0x00000000 0x0 0x80000000>; + }; +}; + +&du { + pinctrl-0 = <&du_pins>; + pinctrl-names = "default"; + status = "okay"; + + clocks = <&cpg CPG_MOD 724>, + <&cpg CPG_MOD 723>, + <&cpg CPG_MOD 721>, + <&versaclock5 1>, + <&x302_clk>, + <&versaclock5 2>; + clock-names = "du.0", "du.1", "du.3", + "dclkin.0", "dclkin.1", "dclkin.3"; +}; + +/* Reference versaclock instead of audio_clk_a */ +&rcar_sound { + clocks = <&cpg CPG_MOD 1005>, + <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>, + <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>, + <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>, + <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>, + <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>, + <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>, + <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>, + <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>, + <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>, + <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>, + <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>, + <&versaclock6_bb 4>, <&audio_clk_b>, + <&audio_clk_c>, + <&cpg CPG_CORE R8A774E1_CLK_S0D4>; +}; From e1076ce07b7736aed269c5d8154f2442970d9137 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Mon, 28 Dec 2020 14:22:21 -0600 Subject: [PATCH 177/584] arm64: dts: renesas: rzg2: Add usb2_clksel to RZ/G2 M/N/H Per the reference manual for the RZ/G Series, 2nd Generation, the RZ/G2M, RZ/G2N, and RZ/G2H have a bit that can be set to choose between a crystal oscillator and an external oscillator. Because only boards that need this should enable it, it's marked as disabled by default for backwards compatibility with existing boards. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20201228202221.2327468-2-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a774a1.dtsi | 15 +++++++++++++++ arch/arm64/boot/dts/renesas/r8a774b1.dtsi | 15 +++++++++++++++ arch/arm64/boot/dts/renesas/r8a774e1.dtsi | 15 +++++++++++++++ 3 files changed, 45 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi index d37ec42a1caa..60e150320ce8 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi @@ -835,6 +835,21 @@ status = "disabled"; }; + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a774a1-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal_clk>, <&usb3s0_clk>; + clock-names = "ehci_ohci", "hs-usb-if", + "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + status = "disabled"; + }; + usb_dmac0: dma-controller@e65a0000 { compatible = "renesas,r8a774a1-usb-dmac", "renesas,usb-dmac"; diff --git a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi index 83523916d360..20003a41a706 100644 --- a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi @@ -709,6 +709,21 @@ status = "disabled"; }; + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a774b1-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal_clk>, <&usb3s0_clk>; + clock-names = "ehci_ohci", "hs-usb-if", + "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + status = "disabled"; + }; + usb_dmac0: dma-controller@e65a0000 { compatible = "renesas,r8a774b1-usb-dmac", "renesas,usb-dmac"; diff --git a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi index 1333b02d623a..2e6c12a46daf 100644 --- a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi @@ -890,6 +890,21 @@ status = "disabled"; }; + usb2_clksel: clock-controller@e6590630 { + compatible = "renesas,r8a774e1-rcar-usb2-clock-sel", + "renesas,rcar-gen3-usb2-clock-sel"; + reg = <0 0xe6590630 0 0x02>; + clocks = <&cpg CPG_MOD 703>, <&cpg CPG_MOD 704>, + <&usb_extal_clk>, <&usb3s0_clk>; + clock-names = "ehci_ohci", "hs-usb-if", + "usb_extal", "usb_xtal"; + #clock-cells = <0>; + power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>; + resets = <&cpg 703>, <&cpg 704>; + reset-names = "ehci_ohci", "hs-usb-if"; + status = "disabled"; + }; + usb_dmac0: dma-controller@e65a0000 { compatible = "renesas,r8a774e1-usb-dmac", "renesas,usb-dmac"; From 8811955d0a6d0abfa3e1c0cee30090fda0015069 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sat, 2 Jan 2021 05:54:12 -0600 Subject: [PATCH 178/584] arm64: dts: renesas: rzg2: Add RPC-IF Support The RZ/G2 series contain the SPI Multi I/O Bus Controller (RPC-IF). Add the nodes, but make them disabled by default. Signed-off-by: Adam Ford Link: https://lore.kernel.org/r/20210102115412.3402059-4-aford173@gmail.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a774a1.dtsi | 17 +++++++++++++++++ arch/arm64/boot/dts/renesas/r8a774b1.dtsi | 17 +++++++++++++++++ arch/arm64/boot/dts/renesas/r8a774c0.dtsi | 17 +++++++++++++++++ arch/arm64/boot/dts/renesas/r8a774e1.dtsi | 17 +++++++++++++++++ 4 files changed, 68 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi index 60e150320ce8..d64fb8b1b86c 100644 --- a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi @@ -2317,6 +2317,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774a1-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = ; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@f1010000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; diff --git a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi index 20003a41a706..5b05474dc272 100644 --- a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi @@ -2175,6 +2175,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774b1-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = ; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sata: sata@ee300000 { compatible = "renesas,sata-r8a774b1", "renesas,rcar-gen3-sata"; diff --git a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi index e0e54342cd4c..20fa3caa050e 100644 --- a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi @@ -1654,6 +1654,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774c0-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = ; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + gic: interrupt-controller@f1010000 { compatible = "arm,gic-400"; #interrupt-cells = <3>; diff --git a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi index 2e6c12a46daf..8eb006cbd9af 100644 --- a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi @@ -2408,6 +2408,23 @@ status = "disabled"; }; + rpc: spi@ee200000 { + compatible = "renesas,r8a774e1-rpc-if", + "renesas,rcar-gen3-rpc-if"; + reg = <0 0xee200000 0 0x200>, + <0 0x08000000 0 0x4000000>, + <0 0xee208000 0 0x100>; + reg-names = "regs", "dirmap", "wbuf"; + interrupts = ; + clocks = <&cpg CPG_MOD 917>; + clock-names = "rpc"; + power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>; + resets = <&cpg 917>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + sata: sata@ee300000 { compatible = "renesas,sata-r8a774e1", "renesas,rcar-gen3-sata"; From 0e3cfb868137cf7ced91d7dc709961000c0dae29 Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Tue, 5 Jan 2021 20:44:16 +0530 Subject: [PATCH 179/584] arm64: dts: ti: k3-j721e-main: Fix supported max outbound regions Cadence IP in J721E supports a maximum of 32 outbound regions. However commit 4e5833884f66 ("arm64: dts: ti: k3-j721e-main: Add PCIe device tree nodes") incorrectly added this as 16 outbound regions. Now that "cdns,max-outbound-regions" is an optional property with default value as 32, remove "cdns,max-outbound-regions" from endpoint DT node. (Since this doesn't impact existing functionality, it need not be backported to older kernels). Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Nishanth Menon Reviewed-by: Vignesh Raghavendra Link: https://lore.kernel.org/r/20210105151421.23237-2-kishon@ti.com --- arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 4 ---- 1 file changed, 4 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi index b32df591c766..1c11da612c67 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi @@ -651,7 +651,6 @@ power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 239 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -700,7 +699,6 @@ power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 240 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -749,7 +747,6 @@ power-domains = <&k3_pds 241 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 241 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; @@ -798,7 +795,6 @@ power-domains = <&k3_pds 242 TI_SCI_PD_EXCLUSIVE>; clocks = <&k3_clks 242 1>; clock-names = "fck"; - cdns,max-outbound-regions = <16>; max-functions = /bits/ 8 <6>; max-virtual-functions = /bits/ 16 <4 4 4 4 0 0>; dma-coherent; From edb96779f3bcbe348f82b458077de0fb96118233 Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Tue, 5 Jan 2021 20:44:17 +0530 Subject: [PATCH 180/584] arm64: dts: ti: k3-j721e-main: Remove "syscon" nodes added for pcieX_ctrl Remove "syscon" nodes added for pcieX_ctrl and have the PCIe node point to the parent with an offset argument. This change is as discussed in [1]. [1] -> http://lore.kernel.org/r/CAL_JsqKiUcO76bo1GoepWM1TusJWoty_BRy2hFSgtEVMqtrvvQ@mail.gmail.com Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Nishanth Menon Reviewed-by: Rob Herring Reviewed-by: Vignesh Raghavendra Link: https://lore.kernel.org/r/20210105151421.23237-3-kishon@ti.com --- arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 48 ++++------------------- 1 file changed, 8 insertions(+), 40 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi index 1c11da612c67..2d526ea44a85 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi @@ -28,38 +28,6 @@ #size-cells = <1>; ranges = <0x0 0x0 0x00100000 0x1c000>; - pcie0_ctrl: syscon@4070 { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x00004070 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x4070 0x4070 0x4>; - }; - - pcie1_ctrl: syscon@4074 { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x00004074 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x4074 0x4074 0x4>; - }; - - pcie2_ctrl: syscon@4078 { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x00004078 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x4078 0x4078 0x4>; - }; - - pcie3_ctrl: syscon@407c { - compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; - reg = <0x0000407c 0x4>; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x407c 0x407c 0x4>; - }; - serdes_ln_ctrl: mux@4080 { compatible = "mmio-mux"; reg = <0x00004080 0x50>; @@ -618,7 +586,7 @@ interrupt-names = "link_state"; interrupts = ; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie0_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4070>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; @@ -645,7 +613,7 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = ; - ti,syscon-pcie-ctrl = <&pcie0_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4070>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 239 TI_SCI_PD_EXCLUSIVE>; @@ -666,7 +634,7 @@ interrupt-names = "link_state"; interrupts = ; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie1_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; @@ -693,7 +661,7 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = ; - ti,syscon-pcie-ctrl = <&pcie1_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; @@ -714,7 +682,7 @@ interrupt-names = "link_state"; interrupts = ; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie2_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4078>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 241 TI_SCI_PD_EXCLUSIVE>; @@ -741,7 +709,7 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = ; - ti,syscon-pcie-ctrl = <&pcie2_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x4078>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 241 TI_SCI_PD_EXCLUSIVE>; @@ -762,7 +730,7 @@ interrupt-names = "link_state"; interrupts = ; device_type = "pci"; - ti,syscon-pcie-ctrl = <&pcie3_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x407c>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 242 TI_SCI_PD_EXCLUSIVE>; @@ -789,7 +757,7 @@ reg-names = "intd_cfg", "user_cfg", "reg", "mem"; interrupt-names = "link_state"; interrupts = ; - ti,syscon-pcie-ctrl = <&pcie3_ctrl>; + ti,syscon-pcie-ctrl = <&scm_conf 0x407c>; max-link-speed = <3>; num-lanes = <2>; power-domains = <&k3_pds 242 TI_SCI_PD_EXCLUSIVE>; From 4c1b22a953d9f8af4d5c2f238fb74dc190d92f04 Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Tue, 5 Jan 2021 20:44:18 +0530 Subject: [PATCH 181/584] arm64: dts: ti: k3-j7200-main: Add SERDES and WIZ device tree node Add dt node for the single instance of WIZ (SERDES wrapper) and SERDES module shared by PCIe, CPSW (SGMII/QSGMII) and USB. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Nishanth Menon Reviewed-by: Vignesh Raghavendra Link: https://lore.kernel.org/r/20210105151421.23237-4-kishon@ti.com --- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 63 +++++++++++++++++++++++ 1 file changed, 63 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index b0094212aa82..fbe4cd1e6e09 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -5,6 +5,13 @@ * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ */ +/ { + serdes_refclk: serdes-refclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; +}; + &cbass_main { msmc_ram: sram@70000000 { compatible = "mmio-sram"; @@ -531,6 +538,62 @@ dma-coherent; }; + serdes_wiz0: wiz@5060000 { + compatible = "ti,j721e-wiz-10g"; + #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 292 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 292 11>, <&k3_clks 292 85>, <&serdes_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + num-lanes = <4>; + #reset-cells = <1>; + ranges = <0x5060000 0x0 0x5060000 0x10000>; + + assigned-clocks = <&k3_clks 292 85>; + assigned-clock-parents = <&k3_clks 292 89>; + + wiz0_pll0_refclk: pll0-refclk { + clocks = <&k3_clks 292 85>, <&serdes_refclk>; + clock-output-names = "wiz0_pll0_refclk"; + #clock-cells = <0>; + assigned-clocks = <&wiz0_pll0_refclk>; + assigned-clock-parents = <&k3_clks 292 85>; + }; + + wiz0_pll1_refclk: pll1-refclk { + clocks = <&k3_clks 292 85>, <&serdes_refclk>; + clock-output-names = "wiz0_pll1_refclk"; + #clock-cells = <0>; + assigned-clocks = <&wiz0_pll1_refclk>; + assigned-clock-parents = <&k3_clks 292 85>; + }; + + wiz0_refclk_dig: refclk-dig { + clocks = <&k3_clks 292 85>, <&serdes_refclk>; + clock-output-names = "wiz0_refclk_dig"; + #clock-cells = <0>; + assigned-clocks = <&wiz0_refclk_dig>; + assigned-clock-parents = <&k3_clks 292 85>; + }; + + wiz0_cmn_refclk_dig_div: cmn-refclk-dig-div { + clocks = <&wiz0_refclk_dig>; + #clock-cells = <0>; + }; + + serdes0: serdes@5060000 { + compatible = "ti,j721e-serdes-10g"; + reg = <0x05060000 0x00010000>; + reg-names = "torrent_phy"; + resets = <&serdes_wiz0 0>; + reset-names = "torrent_reset"; + clocks = <&wiz0_pll0_refclk>; + clock-names = "refclk"; + #address-cells = <1>; + #size-cells = <0>; + }; + }; + usbss0: cdns-usb@4104000 { compatible = "ti,j721e-usb"; reg = <0x00 0x4104000 0x00 0x100>; From 3276d9f53cf660f8ed60d98918170670d0ca6e54 Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Tue, 5 Jan 2021 20:44:19 +0530 Subject: [PATCH 182/584] arm64: dts: ti: k3-j7200-main: Add PCIe device tree node Add PCIe device tree node (both RC and EP) for the single PCIe instance present in j7200. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Nishanth Menon Reviewed-by: Vignesh Raghavendra Link: https://lore.kernel.org/r/20210105151421.23237-5-kishon@ti.com --- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 48 +++++++++++++++++++++++ 1 file changed, 48 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index fbe4cd1e6e09..4e39f0325c03 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -594,6 +594,54 @@ }; }; + pcie1_rc: pcie@2910000 { + compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host"; + reg = <0x00 0x02910000 0x00 0x1000>, + <0x00 0x02917000 0x00 0x400>, + <0x00 0x0d800000 0x00 0x00800000>, + <0x00 0x18000000 0x00 0x00001000>; + reg-names = "intd_cfg", "user_cfg", "reg", "cfg"; + interrupt-names = "link_state"; + interrupts = ; + device_type = "pci"; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; + max-link-speed = <3>; + num-lanes = <4>; + power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 240 6>; + clock-names = "fck"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xf>; + cdns,no-bar-match-nbits = <64>; + vendor-id = /bits/ 16 <0x104c>; + device-id = /bits/ 16 <0xb00f>; + msi-map = <0x0 &gic_its 0x0 0x10000>; + dma-coherent; + ranges = <0x01000000 0x0 0x18001000 0x00 0x18001000 0x0 0x0010000>, + <0x02000000 0x0 0x18011000 0x00 0x18011000 0x0 0x7fef000>; + dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>; + }; + + pcie1_ep: pcie-ep@2910000 { + compatible = "ti,j7200-pcie-ep", "ti,j721e-pcie-ep"; + reg = <0x00 0x02910000 0x00 0x1000>, + <0x00 0x02917000 0x00 0x400>, + <0x00 0x0d800000 0x00 0x00800000>, + <0x00 0x18000000 0x00 0x08000000>; + reg-names = "intd_cfg", "user_cfg", "reg", "mem"; + interrupt-names = "link_state"; + interrupts = ; + ti,syscon-pcie-ctrl = <&scm_conf 0x4074>; + max-link-speed = <3>; + num-lanes = <4>; + power-domains = <&k3_pds 240 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 240 6>; + clock-names = "fck"; + max-functions = /bits/ 8 <6>; + dma-coherent; + }; + usbss0: cdns-usb@4104000 { compatible = "ti,j721e-usb"; reg = <0x00 0x4104000 0x00 0x100>; From 429c0259f17f4fdf9c0beb5423b0c8f6c2ea2e8c Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Tue, 5 Jan 2021 20:44:20 +0530 Subject: [PATCH 183/584] arm64: dts: ti: k3-j7200-common-proc-board: Enable SERDES0 Add sub-nodes to SERDES0 DT node to represent SERDES0 is connected to PCIe and QSGMII (multi-link SERDES). Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Nishanth Menon Reviewed-by: Vignesh Raghavendra Link: https://lore.kernel.org/r/20210105151421.23237-6-kishon@ti.com --- .../dts/ti/k3-j7200-common-proc-board.dts | 23 +++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index 331b388e1d1b..def98f563336 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -8,6 +8,7 @@ #include "k3-j7200-som-p0.dtsi" #include #include +#include / { chosen { @@ -218,3 +219,25 @@ ti,adc-channels = <0 1 2 3 4 5 6 7>; }; }; + +&serdes_refclk { + clock-frequency = <100000000>; +}; + +&serdes0 { + serdes0_pcie_link: phy@0 { + reg = <0>; + cdns,num-lanes = <2>; + #phy-cells = <0>; + cdns,phy-type = ; + resets = <&serdes_wiz0 1>, <&serdes_wiz0 2>; + }; + + serdes0_qsgmii_link: phy@1 { + reg = <2>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = ; + resets = <&serdes_wiz0 3>; + }; +}; From 3a6319df506f1a821abad2c71a580a2f7b78a304 Mon Sep 17 00:00:00 2001 From: Kishon Vijay Abraham I Date: Tue, 5 Jan 2021 20:44:21 +0530 Subject: [PATCH 184/584] arm64: dts: ti: k3-j7200-common-proc-board: Enable PCIe x2 lane PCIe slot in the common processor board is enabled and connected to j7200 SOM. Add PCIe DT node in common processor board to reflect the same. Signed-off-by: Kishon Vijay Abraham I Signed-off-by: Nishanth Menon Reviewed-by: Vignesh Raghavendra Link: https://lore.kernel.org/r/20210105151421.23237-7-kishon@ti.com --- .../boot/dts/ti/k3-j7200-common-proc-board.dts | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts index def98f563336..4a7182abccf5 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts @@ -6,6 +6,7 @@ /dts-v1/; #include "k3-j7200-som-p0.dtsi" +#include #include #include #include @@ -241,3 +242,17 @@ resets = <&serdes_wiz0 3>; }; }; + +&pcie1_rc { + reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <2>; +}; + +&pcie1_ep { + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <2>; + status = "disabled"; +}; From e5376f2ea2e2de4519092287382efdb226acec27 Mon Sep 17 00:00:00 2001 From: Douglas Anderson Date: Mon, 7 Dec 2020 14:33:02 -0800 Subject: [PATCH 185/584] arm64: dts: qcom: Clean up sc7180-trogdor voltage rails For a bunch of rails we really don't do anything with them in Linux. These are things like modem voltage rails that the modem manages these itself and core rails (like IO rails) that are setup to just automagically do the right thing by the firmware. Let's stop even listing those rails in our device tree. The net result of this is that some of these rails might be able to go down to a lower voltage or perhaps transition to LPM (low power mode) sometimes. Here's a list of what we're doing and why: * L1A - only goes to SoC and doesn't seem associated with any particular peripheral. Kernel isn't doing anything with this. Removing from dts. NET IMPACT: rail might drop from 1.2V to 1.178V and switch to LPM in some cases depending on firmware. * L2A - only goes to SoC and doesn't seem associated with any particular peripheral. Kernel isn't doing anything with this. Removing from dts. NET IMPACT: rail might switch to LPM in some cases depending on firmware. * L3A - only goes to SoC and doesn't seem associated with any particular peripheral. Kernel isn't doing anything with this. Removing from dts. NET IMPACT: rail might switch to LPM in some cases depending on firmware. * L5A - seems to be totally unused as far as I can tell and doesn't even come off QSIP. Removing from dts. * L6A - only goes to SoC and doesn't seem associated with any particular peripheral (I think?). Kernel isn't doing anything with this. Removing from dts. NET IMPACT: rail might switch to LPM in some cases depending on firmware. * L16A - Looks like this is only used for internal RF stuff. Removing from dts. NET IMPACT: rail might switch to LPM in some cases depending on firmware. * L1C - Just goes to WiFi / Bluetooth. Trust how IDP has this set and put this back at 1.616V min. * L4C - This goes out to the eSIM among other places. This looks like it's intended to be for SIM card and modem manages. NET IMPACT: rail might switch to LPM in some cases depending on firmware. * L5C - This goes to the physical SIM. This looks like it's intended to be for SIM card and modem manages. NET IMPACT: rail might drop from 1.8V to 1.648V and switch to LPM in some cases depending on firmware. NOTE: in general for anything which is supposed to be managed by Linux I still left it all forced to HPM since I'm not 100% sure that all the needed calls to regulator_set_load() are in place and HPM is safer. Switching more things to LPM can happen in a future patch. ALSO NOTE: Power measurements showed no measurable difference after applying this patch, so perhaps it should be viewed more as a cleanup than any power savings. Reviewed-by: Alexandru M Stan Signed-off-by: Douglas Anderson Link: https://lore.kernel.org/r/20201207143255.1.Ib92ec35163682dec4b2fbb4bde0785cb6e6dde27@changeid Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi | 82 ++------------------ 1 file changed, 7 insertions(+), 75 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi index e3a3d809448f..07c8b2c926c0 100644 --- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi @@ -298,40 +298,6 @@ regulator-max-microvolt = <1128000>; }; - /* - * pp2040_s5a (smps5) and pp1056_s4a (smps4) are just - * inputs to other rails on AOP-managed PMICs on trogdor. - * The system is already configured to manage these rails - * automatically (enable when needed, adjust voltage for - * headroom) so we won't specify anything here. - * - * NOTE: though the rails have a voltage implied by their - * name, the automatic headroom calculation might not result - * in them being that voltage. ...and that's OK. - * Specifically the only point of these rails is to provide - * an input source for other rails and if we can satisify the - * needs of those other rails with a lower source voltage then - * we save power. - */ - - pp1200_l1a: ldo1 { - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - regulator-initial-mode = ; - }; - - pp1000_l2a: ldo2 { - regulator-min-microvolt = <944000>; - regulator-max-microvolt = <1056000>; - regulator-initial-mode = ; - }; - - pp1000_l3a: ldo3 { - regulator-min-microvolt = <968000>; - regulator-max-microvolt = <1064000>; - regulator-initial-mode = ; - }; - vdd_qlink_lv: vdd_qlink_lv_ck: vdd_qusb_hs0_core: @@ -350,24 +316,6 @@ regulator-initial-mode = ; }; - pp2700_l5a: ldo5 { - regulator-min-microvolt = <2704000>; - regulator-max-microvolt = <2704000>; - regulator-initial-mode = ; - }; - - ebi0_cal: - ebi1_cal: - vddio_ck_ebi0: - vddio_ck_ebi1: - vddio_ebi0: - vddq: - pp600_l6a: ldo6 { - regulator-min-microvolt = <568000>; - regulator-max-microvolt = <648000>; - regulator-initial-mode = ; - }; - vdd_cx_wlan: pp800_l9a: ldo9 { regulator-min-microvolt = <488000>; @@ -404,6 +352,11 @@ regulator-initial-mode = ; }; + /* + * On trogdor this needs to match l10a since we use it to + * give power to things like SPI flash which communicate back + * on lines powered by l10a. Thus we force to 1.8V. + */ pp1800_l13a: ldo13 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; @@ -424,12 +377,6 @@ regulator-initial-mode = ; }; - pp2700_l16a: ldo16 { - regulator-min-microvolt = <2496000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = ; - }; - vdda_qusb_hs0_3p1: vdd_pdphy: pp3100_l17a: ldo17 { @@ -463,8 +410,8 @@ }; pp1800_l1c: ldo1 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1616000>; + regulator-max-microvolt = <1984000>; regulator-initial-mode = ; }; @@ -491,21 +438,6 @@ regulator-initial-mode = ; }; - ld_pp1800_esim_l4c: - vddpx_5: - pp1800_l4c: ldo4 { - regulator-min-microvolt = <1648000>; - regulator-max-microvolt = <3304000>; - regulator-initial-mode = ; - }; - - vddpx_6: - pp1800_l5c: ldo5 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-initial-mode = ; - }; - vddpx_2: ppvar_l6c: ldo6 { regulator-min-microvolt = <1800000>; From b2e3f897684ccc03139c8455e17abcc27bb5d491 Mon Sep 17 00:00:00 2001 From: Danny Lin Date: Tue, 5 Jan 2021 12:10:00 -0800 Subject: [PATCH 186/584] arm64: dts: qcom: sm8150: Add support for deep CPU cluster idle This commit adds support for deep idling of the entire unified DynamIQ CPU cluster on sm8150. In this idle state, the LLCC (Last-Level Cache Controller) is powered off and the AOP (Always-On Processor) enters a low-power sleep state. I'm not sure what the per-CPU 0x400000f4 idle state previously contributed by Qualcomm as the "cluster sleep" state is, but the downstream kernel has no such state. The real deep cluster idle state is 0x41000c244, composed of: Cluster idle state: (0xc24) << 4 = 0xc240 Is reset state: 1 << 30 = 0x40000000 Affinity level: 1 << 24 = 0x1000000 CPU idle state: 0x4 (power collapse) This setup can be replicated with the PSCI power domain cpuidle driver, which utilizes OSI to enter cluster idle when the last active CPU enters idle. The cluster idle state cannot be used as a plain cpuidle state because it requires that all CPUs in the cluster are idling. Reviewed-by: Ulf Hansson Signed-off-by: Danny Lin Link: https://lore.kernel.org/r/20210105201000.913183-1-danny@kdrag0n.dev Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 91 ++++++++++++++++++++++------ 1 file changed, 73 insertions(+), 18 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 84d3c8a0b7f1..9a939c6095ea 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -49,10 +49,10 @@ enable-method = "psci"; capacity-dmips-mhz = <488>; dynamic-power-coefficient = <232>; - cpu-idle-states = <&LITTLE_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD0>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_0: l2-cache { compatible = "cache"; @@ -70,10 +70,10 @@ enable-method = "psci"; capacity-dmips-mhz = <488>; dynamic-power-coefficient = <232>; - cpu-idle-states = <&LITTLE_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD1>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_100: l2-cache { compatible = "cache"; @@ -89,10 +89,10 @@ enable-method = "psci"; capacity-dmips-mhz = <488>; dynamic-power-coefficient = <232>; - cpu-idle-states = <&LITTLE_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD2>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_200: l2-cache { compatible = "cache"; @@ -107,10 +107,10 @@ enable-method = "psci"; capacity-dmips-mhz = <488>; dynamic-power-coefficient = <232>; - cpu-idle-states = <&LITTLE_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; + power-domains = <&CPU_PD3>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_300: l2-cache { compatible = "cache"; @@ -125,10 +125,10 @@ enable-method = "psci"; capacity-dmips-mhz = <1024>; dynamic-power-coefficient = <369>; - cpu-idle-states = <&BIG_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; + power-domains = <&CPU_PD4>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_400: l2-cache { compatible = "cache"; @@ -143,10 +143,10 @@ enable-method = "psci"; capacity-dmips-mhz = <1024>; dynamic-power-coefficient = <369>; - cpu-idle-states = <&BIG_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; + power-domains = <&CPU_PD5>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_500: l2-cache { compatible = "cache"; @@ -161,10 +161,10 @@ enable-method = "psci"; capacity-dmips-mhz = <1024>; dynamic-power-coefficient = <369>; - cpu-idle-states = <&BIG_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; + power-domains = <&CPU_PD6>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_600: l2-cache { compatible = "cache"; @@ -179,10 +179,10 @@ enable-method = "psci"; capacity-dmips-mhz = <1024>; dynamic-power-coefficient = <421>; - cpu-idle-states = <&BIG_CPU_SLEEP_0 - &CLUSTER_SLEEP_0>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; + power-domains = <&CPU_PD7>; + power-domain-names = "psci"; #cooling-cells = <2>; L2_700: l2-cache { compatible = "cache"; @@ -248,11 +248,13 @@ min-residency-us = <4488>; local-timer-stop; }; + }; + domain-idle-states { CLUSTER_SLEEP_0: cluster-sleep-0 { - compatible = "arm,idle-state"; + compatible = "domain-idle-state"; idle-state-name = "cluster-power-collapse"; - arm,psci-suspend-param = <0x400000F4>; + arm,psci-suspend-param = <0x4100c244>; entry-latency-us = <3263>; exit-latency-us = <6562>; min-residency-us = <9987>; @@ -288,6 +290,59 @@ psci { compatible = "arm,psci-1.0"; method = "smc"; + + CPU_PD0: cpu0 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD1: cpu1 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD2: cpu2 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD3: cpu3 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&LITTLE_CPU_SLEEP_0>; + }; + + CPU_PD4: cpu4 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD5: cpu5 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD6: cpu6 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CPU_PD7: cpu7 { + #power-domain-cells = <0>; + power-domains = <&CLUSTER_PD>; + domain-idle-states = <&BIG_CPU_SLEEP_0>; + }; + + CLUSTER_PD: cpu-cluster0 { + #power-domain-cells = <0>; + domain-idle-states = <&CLUSTER_SLEEP_0>; + }; }; reserved-memory { From 7f230c86de7d3ae11aec87e712caf63b5ed7f593 Mon Sep 17 00:00:00 2001 From: Sergio Sota Date: Fri, 8 Jan 2021 11:38:19 +0100 Subject: [PATCH 187/584] ARM: dts: sun5i: add A10s/A13 mali gpu support fallback The A10s/A13 mali gpu was not defined in device tree Add A10 mali gpu as a fallback for A10s/A13 Tested with Olimex-A13-SOM / Olimex-A13-OlinuXino-MICRO "kmscube" 3d cube on screen (60fps / 10%cpu) Versions: Lima:1.1.0 EGL:1.4 OpenGLES:2.0 Mesa:20.2.2 Signed-off-by: Sergio Sota Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210108103819.322901-1-sergiosota@fanamoel.com --- arch/arm/boot/dts/sun5i.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi index c2b4fbf552a3..250d6b87ab4d 100644 --- a/arch/arm/boot/dts/sun5i.dtsi +++ b/arch/arm/boot/dts/sun5i.dtsi @@ -726,6 +726,18 @@ #size-cells = <0>; }; + mali: gpu@1c40000 { + compatible = "allwinner,sun4i-a10-mali", "arm,mali-400"; + reg = <0x01c40000 0x10000>; + interrupts = <69>, <70>, <71>, <72>, <73>; + interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pmu"; + clocks = <&ccu CLK_AHB_GPU>, <&ccu CLK_GPU>; + clock-names = "bus", "core"; + resets = <&ccu RST_GPU>; + assigned-clocks = <&ccu CLK_GPU>; + assigned-clock-rates = <320000000>; + }; + timer@1c60000 { compatible = "allwinner,sun5i-a13-hstimer"; reg = <0x01c60000 0x1000>; From 0b26926a96429bda01a261d2c2a6faa1ef3b8e7b Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Tue, 12 Jan 2021 22:05:42 -0600 Subject: [PATCH 188/584] arm64: dts: allwinner: pinephone: Support volume key wakeup PinePhone volume keys are connected to the LRADC in the A64. Users may want to use them to wake the device from sleep. Support this by declaring the LRADC as a wakeup source. Reviewed-by: Hans de Goede Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113040542.34247-4-samuel@sholland.org --- arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index 2dfe9bae8c67..7f37f9fea0ab 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -196,6 +196,7 @@ &lradc { vref-supply = <®_aldo3>; + wakeup-source; status = "okay"; button-200 { From 53441b8ef7defb47883c2e75964f52873b25d32b Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sun, 10 Jan 2021 22:16:06 +0100 Subject: [PATCH 189/584] arm64: dts: allwinner: h6: PineH64 model B: Add bluetooth PineH64 model B has wifi+bt combo module. Wifi is already supported, so lets add also bluetooth node. Signed-off-by: Jernej Skrabec Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210110211606.3733056-1-jernej.skrabec@siol.net --- .../dts/allwinner/sun50i-h6-pine-h64-model-b.dts | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts index 7fea1e4e2d49..645bd8761eb5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts @@ -34,3 +34,18 @@ non-removable; status = "okay"; }; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; + uart-has-rtscts; + status = "okay"; + + bluetooth { + compatible = "realtek,rtl8723bs-bt"; + device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ + host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ + enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ + max-speed = <1500000>; + }; +}; From 78894adedd87ebe2af60148c773780022a151fbc Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 2 Nov 2020 00:22:40 +0100 Subject: [PATCH 190/584] ARM: dts: ux500: Add a device tree for Janice This adds a basic device tree for the Samsung GT-I9070 mobile phone also known as Janice. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/Makefile | 1 + .../arm/boot/dts/ste-ux500-samsung-janice.dts | 894 ++++++++++++++++++ 2 files changed, 895 insertions(+) create mode 100644 arch/arm/boot/dts/ste-ux500-samsung-janice.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..e86bb4a9d521 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1278,6 +1278,7 @@ dtb-$(CONFIG_ARCH_U8500) += \ ste-hrefv60plus-tvk.dtb \ ste-href520-tvk.dtb \ ste-ux500-samsung-golden.dtb \ + ste-ux500-samsung-janice.dtb \ ste-ux500-samsung-skomer.dtb dtb-$(CONFIG_ARCH_UNIPHIER) += \ uniphier-ld4-ref.dtb \ diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts new file mode 100644 index 000000000000..31ee34e79fe1 --- /dev/null +++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts @@ -0,0 +1,894 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice. + */ + +/dts-v1/; +#include "ste-db8500.dtsi" +#include "ste-ab8500.dtsi" +#include "ste-dbx5x0-pinctrl.dtsi" +#include +#include +#include + +/ { + model = "Samsung Galaxy S Advance (GT-I9070)"; + compatible = "samsung,janice", "st-ericsson,u8500"; + + chosen { + stdout-path = &serial2; + }; + + /* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */ + ldo_3v3_reg: regulator-gpio-ldo-3v3 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VMEM_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>; + startup-delay-us = <5000>; // FIXME + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_ldo_en_default_mode>; + }; + + /* + * External Ricoh "TSP" regulator for the touchscreen. + * One GPIO line controls two voltages of 3.3V and 1.8V + * this line is known as "TSP_LDO_ON1" in the schematics. + */ + ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "LDO_TSP_A3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* GPIO94 controls this regulator */ + gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_ldo_en_default_mode>; + }; + ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_TSP_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO94 controls this regulator */ + gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_ldo_en_default_mode>; + }; + + /* + * External Ricoh "TSP" regulator for the touchkeys. + * Two GPIO lines controls two voltages of 3.3V and 1.8V + * TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8 + * EN_LED_LDO controls VREG_KLED_3V3 (key LED) + */ + ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_KLED_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* GPIO68 controls this regulator */ + gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&en_led_ldo_default_mode>; + }; + ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_TOUCHKEY_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO89 controls this regulator */ + gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>; + /* 70 ms power-on delay */ + startup-delay-us = <70000>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_ldo_on2_default_mode>; + }; + + + /* + * External Ricoh RP152L010B-TR LCD LDO regulator for the display. + * LCD_PWR_EN controls a 3.0V and 1.8V output. + */ + lcd_3v0_reg: regulator-gpio-lcd-3v0 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_LCD_3V0"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + /* GPIO219 controls this regulator */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pwr_en_default_mode>; + }; + lcd_1v8_reg: regulator-gpio-lcd-1v8 { + compatible = "regulator-fixed"; + /* Supplied in turn by VBAT */ + regulator-name = "VREG_LCD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + /* GPIO219 controls this regulator */ + gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pwr_en_default_mode>; + }; + + /* + * This regulator is a GPIO line that drives the Broadcom WLAN + * line BT_VREG_EN high and enables the internal regulators + * inside the chip. + * + * The voltage specified here is only used to determine the OCR mask, + * the for the SDIO connector, the chip is actually connected + * directly to VBAT. + */ + wl_bt_reg: regulator-gpio-wlan { + compatible = "regulator-fixed"; + regulator-name = "BT_VREG_EN"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + startup-delay-us = <100000>; + /* GPIO222 (BT_VREG_EN) */ + gpio = <&gpio6 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_ldo_en_default>; + }; + + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default_mode>; + + button-home { + linux,code = ; + label = "HOME"; + /* GPIO91 */ + gpios = <&gpio2 27 GPIO_ACTIVE_LOW>; + }; + button-volup { + linux,code = ; + label = "VOL+"; + /* GPIO67 */ + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + }; + button-voldown { + linux,code = ; + label = "VOL-"; + /* GPIO92 */ + gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; + }; + }; + + /* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */ + i2c-gpio-0 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_0_default>; + #address-cells = <1>; + #size-cells = <0>; + + /* Yamaha YAS530 magnetometer */ + magnetometer@2e { + compatible = "yamaha,yas530"; + reg = <0x2e>; + /* VDD 3V */ + vdd-supply = <&ab8500_ldo_aux1_reg>; + /* IOVDD 1.8V */ + iovdd-supply = <&ab8500_ldo_aux2_reg>; + /* GPIO204 COMPASS_RST_N */ + reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&yas529_default>; + }; + /* TODO: this should also be used by the NCP6914 Camera power management unit */ + }; + + /* + * These pins do have an spi controller, however the controller on + * these pins is not the fully featured PL022 SSP/SPI block but the + * ST Micro diet "PL023" version. One of the lacking features in + * this derivative is 3wire support, so it cannot be used to drive + * this panel interface. We have to use GPIO bit-banging instead. + */ + spi-gpio-0 { + compatible = "spi-gpio"; + /* Clock on GPIO220 */ + sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>; + /* MISO/MOSI on GPIO224 (no separate MISO pin) */ + mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>; + /* Chip select on GPIO223 */ + cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>; + num-chipselects = <1>; + + pinctrl-names = "default"; + pinctrl-0 = <&spi_gpio_0_default>; + #address-cells = <1>; + #size-cells = <0>; + + panel@0 { + compatible = "samsung,s6e63m0"; + reg = <0>; + vdd3-supply = <&lcd_3v0_reg>; + vci-supply = <&lcd_1v8_reg>; + /* Reset on GPIO139 */ + reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&panel_default_mode>; + spi-3wire; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + + /* + * Current sense amplifier on the light sensor to convert current to + * voltage. We do not know if this is the actual configuration. The + * sense resistor value was found by calibrating in a room ambient + * light with a second mobile phone light sensor as reference. If you + * pry a Janice phone apart and inspect it you may figure this out. + */ + gp2a_shunt: current-sense-shunt { + compatible = "current-sense-shunt"; + io-channels = <&gpadc 0x07>; + shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */ + #io-channel-cells = <0>; + io-channel-ranges; + }; + + /* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */ + i2c-gpio-1 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_1_default>; + #address-cells = <1>; + #size-cells = <0>; + + touchkey@20 { + compatible = "coreriver,tc360-touchkey"; + reg = <0x20>; + vdd-supply = <&ldo_kled_3v3_reg>; + vcc-supply = <&ldo_touchkey_1v8_reg>; + vddio-supply = <&ldo_touchkey_1v8_reg>; + + /* Interrupt on GPIO 198 */ + interrupt-parent = <&gpio6>; + interrupts = <6 IRQ_TYPE_EDGE_RISING>; + + pinctrl-names = "default"; + pinctrl-0 = <&touchkey_default_mode>; + linux,keycodes = ; + }; + }; + + /* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */ + i2c-gpio-2 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_2_default>; + #address-cells = <1>; + #size-cells = <0>; + /* TODO: add the Immersion ISA1200 I2C device here */ + }; + + /* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */ + i2c-gpio-3 { + compatible = "i2c-gpio"; + sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c_gpio_3_default>; + #address-cells = <1>; + #size-cells = <0>; + + nfc@30 { + compatible = "nxp,pn547", "nxp,nxp-nci-i2c"; + reg = <0x30>; + /* NFC IRQ on GPIO32 */ + interrupt-parent = <&gpio1>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + /* GPIO 31 */ + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + /* GPIO88 */ + enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pn547_janice_default>; + }; + }; + + soc { + /* External Micro SD slot */ + sdi0_per1@80126000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + st,sig-dir-cmd; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-pin-fbclk; + full-pwr-cycle; + /* MMC is powered by AUX3 1.2V .. 2.91V */ + vmmc-supply = <&ab8500_ldo_aux3_reg>; + /* 2.9 V level translator is using AUX3 at 2.9 V as well */ + vqmmc-supply = <&ab8500_ldo_aux3_reg>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc0_a_2_default>; + pinctrl-1 = <&mc0_a_2_sleep>; + cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217 + status = "okay"; + }; + + /* WLAN SDIO channel */ + sdi1_per2@80118000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <4>; + non-removable; + cap-sd-highspeed; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc1_a_2_default>; + pinctrl-1 = <&mc1_a_2_sleep>; + /* + * GPIO-controlled voltage enablement: this drives + * the BT_VREG_EN line high when we use this device. + * Represented as regulator to fill OCR mask and to + * be usable in parallel with the Bluetooth chip. + */ + vmmc-supply = <&wl_bt_reg>; + + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + wifi@1 { + /* Actually BRCM4330 */ + compatible = "brcm,bcm4329-fmac"; + reg = <1>; + /* GPIO216 WL_HOST_WAKE */ + interrupt-parent = <&gpio6>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "host-wake"; + /* GPIO215 WLAN_RST_N */ + /* FIXME: kernel does not use this assert/deassert */ + reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&wlan_default_mode>; + }; + }; + + /* eMMC */ + sdi2_per3@80005000 { + arm,primecell-periphid = <0x10480180>; + max-frequency = <50000000>; + bus-width = <8>; + non-removable; + cap-mmc-highspeed; + mmc-ddr-1_8v; + vmmc-supply = <&ldo_3v3_reg>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mc2_a_1_default>; + pinctrl-1 = <&mc2_a_1_sleep>; + status = "okay"; + }; + + /* GBF (Bluetooth) UART */ + uart@80120000 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u0_a_1_default>; + pinctrl-1 = <&u0_a_1_sleep>; + status = "okay"; + + bluetooth { + compatible = "brcm,bcm4330-bt"; + /* + * We actually have shutdown-gpios, BT_VREG_EN on GPIO222, + * but since this GPIO is shared with the WLAN chip, we need + * to reference the regulator instead. The regulator + * framework will reference count the GPIO usage and + * make sure we can use the same GPIO for several supplies. + */ + // shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>; + vbat-supply = <&wl_bt_reg>; + /* BT_WAKE on GPIO199 */ + device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; + /* BT_HOST_WAKE on GPIO97 */ + /* FIXME: convert to interrupt */ + host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>; + /* BT_RST_N on GPIO209 */ + reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&bluetooth_default_mode>; + }; + }; + + /* GPS UART */ + uart@80121000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + /* CTS/RTS is not used, CTS is repurposed as GPIO */ + pinctrl-0 = <&u1rxtx_a_1_default>; + pinctrl-1 = <&u1rxtx_a_1_sleep>; + /* FIXME: add a device for the GPS here */ + }; + + /* Debugging console UART connected to TSU6111RSVR (FSA880) */ + uart@80007000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&u2rxtx_c_1_default>; + pinctrl-1 = <&u2rxtx_c_1_sleep>; + }; + + prcmu@80157000 { + ab8500 { + ab8500_usb { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&usb_a_1_default>; + pinctrl-1 = <&usb_a_1_sleep>; + }; + + ab8500-regulators { + ab8500_ldo_aux1 { + /* Used for VDD for sensors */ + regulator-name = "V-SENSORS-VDD"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ab8500_ldo_aux2 { + /* Used for VIO for sensors */ + regulator-name = "V-SENSORS-VIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ab8500_ldo_aux3 { + /* Used for voltage for external MMC/SD card */ + regulator-name = "V-MMC-SD"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2910000>; + }; + }; + }; + }; + + /* I2C0 */ + i2c@80004000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c0_a_1_default>; + pinctrl-1 = <&i2c0_a_1_sleep>; + + proximity@44 { + /* Janice has the GP2AP002A00F with light sensor */ + compatible = "sharp,gp2ap002a00f"; + clock-frequency = <400000>; + reg = <0x44>; + + interrupt-parent = <&gpio4>; + interrupts = <18 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&ab8500_ldo_aux1_reg>; + vio-supply = <&ab8500_ldo_aux2_reg>; + /* ADC channel AUX2 to read ALSOUT ambient light sensor out */ + io-channels = <&gp2a_shunt>; + io-channel-names = "alsout"; + pinctrl-names = "default"; + pinctrl-0 = <&gp2ap002_janice_default>; + /* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */ + sharp,proximity-far-hysteresis = /bits/ 8 <0x40>; + sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>; + }; + }; + + /* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */ + i2c@80122000 { + status = "okay"; + pinctrl-names = "default","sleep"; + pinctrl-0 = <&i2c1_b_2_default>; + pinctrl-1 = <&i2c1_b_2_sleep>; + + /* Texas Instruments TSU6111 micro USB switch */ + usb-switch@25 { + compatible = "ti,tsu6111"; + reg = <0x25>; + /* Interrupt JACK_INT_N on GPIO95 */ + interrupt-parent = <&gpio2>; + interrupts = <31 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&tsu6111_janice_default>; + }; + }; + + /* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */ + i2c@80128000 { + status = "okay"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c2_b_2_default>; + pinctrl-1 = <&i2c2_b_2_sleep>; + + gyroscope@68 { + compatible = "invensense,mpu3050"; + reg = <0x68>; + /* GPIO226 interrupt */ + interrupt-parent = <&gpio7>; + interrupts = <2 IRQ_TYPE_EDGE_FALLING>; + /* FIXME: no idea about this */ + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V + vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V + pinctrl-names = "default"; + pinctrl-0 = <&mpu3050_janice_default>; + + /* + * The MPU-3050 acts as a hub for the + * accelerometer. + */ + i2c-gate { + #address-cells = <1>; + #size-cells = <0>; + + /* Bosch BMA222 accelerometer */ + accelerometer@08 { + compatible = "bosch,bma222"; + reg = <0x08>; + /* FIXME: no idea about this */ + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "1"; + vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V + vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V + }; + }; + }; + }; + + /* I2C3 */ + i2c@80110000 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c3_c_2_default>; + pinctrl-1 = <&i2c3_c_2_sleep>; + + /* Atmel mXT224E touchscreen */ + touchscreen@4a { + compatible = "atmel,maxtouch"; + reg = <0x4a>; + /* GPIO218 (TSP_INT_1V8) */ + interrupt-parent = <&gpio6>; + interrupts = <26 IRQ_TYPE_EDGE_FALLING>; + /* VDDA is "analog supply", 2.57-3.47 V */ + vdda-supply = <&ldo_tsp_3v3_reg>; + /* VDD is "digital supply" 1.71-3.47V */ + vdd-supply = <&ldo_tsp_1v8_reg>; + pinctrl-names = "default"; + pinctrl-0 = <&tsp_default>; + }; + }; + + mcde@a0350000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dpi_default_mode>; + + port { + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + }; +}; + +&pinctrl { + /* + * This extends the MC0_A_2 default config to include + * the card detect GPIO217 line. + */ + sdi0 { + mc0_a_2_default { + default_cfg4 { + pins = "GPIO217_AH12"; /* card detect */ + ste,config = <&gpio_in_pd>; + }; + }; + }; + mcde { + dpi_default_mode: dpi_default { + default_mux1 { + /* Mux in all the data lines */ + function = "lcd"; + groups = + /* Data lines D0-D7 GPIO70..GPIO77 */ + "lcd_d0_d7_a_1", + /* Data lines D8-D11 GPIO78..GPIO81 */ + "lcd_d8_d11_a_1", + /* Data lines D12-D15 GPIO82..GPIO85 */ + "lcd_d12_d15_a_1", + /* Data lines D16-D23 GPIO161..GPIO168 */ + "lcd_d16_d23_b_1"; + }; + default_mux2 { + function = "lcda"; + /* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */ + groups = "lcdaclk_b_1", "lcda_b_1"; + }; + /* Input, no pull-up is the default state for pins used for an alt function */ + default_cfg1 { + pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23"; + ste,config = <&in_nopull>; + }; + }; + }; + /* GPIO for panel reset control */ + panel { + panel_default_mode: panel_default { + janice_cfg1 { + /* Reset line */ + pins = "GPIO139_C9"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the eMMC */ + emmc-ldo { + emmc_ldo_en_default_mode: emmc_ldo_default { + /* LDO enable on GPIO6 */ + janice_cfg1 { + pins = "GPIO6_AF6"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the touchscreen */ + tsp-ldo { + tsp_ldo_en_default_mode: tsp_ldo_default { + /* LDO enable on GPIO94 */ + janice_cfg1 { + pins = "GPIO94_D7"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the key LED */ + key-led { + en_led_ldo_default_mode: en_led_ldo_default { + /* EN_LED_LDO on GPIO68 */ + janice_cfg1 { + pins = "GPIO68_E1"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the LDO regulator for the touchkeys */ + touchkey-ldo { + tsp_ldo_on2_default_mode: tsp_ldo_on2_default { + /* TSP_LDO_ON2 on GPIO89 */ + janice_cfg1 { + pins = "GPIO89_E6"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + touchkey { + touchkey_default_mode: touchkey_default { + janice_cfg1 { + /* Interrupt */ + pins = "GPIO198_AG25"; + ste,config = <&gpio_in_nopull>; + }; + janice_cfg2 { + /* Reset, actually completely unused (not routed) */ + pins = "GPIO205_AG23"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + /* GPIO that enabled the LDO regulator for the LCD display */ + lcd-ldo { + lcd_pwr_en_default_mode: lcd_pwr_en_default { + /* LCD_PWR_EN on GPIO219 */ + janice_cfg1 { + pins = "GPIO219_AG10"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* GPIO that enables the WLAN internal LDO regulators */ + wlan-ldo { + wlan_ldo_en_default: wlan_ldo_default { + /* GPIO222 BT_VREG_ON */ + janice_cfg1 { + pins = "GPIO222_AJ9"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + /* GPIO keys */ + gpio-keys { + gpio_keys_default_mode: gpio_keys_default { + skomer_cfg1 { + pins = "GPIO67_G2", /* VOL UP */ + "GPIO91_B6", /* HOME */ + "GPIO92_D6"; /* VOL DOWN */ + ste,config = <&gpio_in_pu>; + }; + }; + }; + /* Interrupt line for the Atmel MXT228 touchscreen */ + tsp { + tsp_default: tsp_default { + janice_cfg1 { + pins = "GPIO218_AH11"; /* TSP_INT_1V8 */ + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* Reset line for the Yamaha YAS529 magnetometer */ + yas529 { + yas529_default: yas529_janice { + janice_cfg1 { + pins = "GPIO204_AF23"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* Interrupt line for light/proximity sensor GP2AP002 */ + gp2ap002 { + gp2ap002_janice_default: gp2ap002_janice { + janice_cfg1 { + pins = "GPIO146_D13"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* Interrupt line for Invensense MPU3050 gyroscope */ + mpu3050 { + mpu3050_janice_default: mpu3050_janice { + janice_cfg1 { + /* GPIO226 used for IRQ */ + pins = "GPIO226_AF8"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for magnetometer and NCP6914 */ + i2c-gpio-0 { + i2c_gpio_0_default: i2c_gpio_0 { + janice_cfg1 { + pins = "GPIO143_D12", "GPIO144_B13"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for the Cypress touchkeys */ + i2c-gpio-1 { + i2c_gpio_1_default: i2c_gpio_1 { + janice_cfg1 { + pins = "GPIO196_AG26", "GPIO197_AH24"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for the Immersion ISA1200 */ + i2c-gpio-2 { + i2c_gpio_2_default: i2c_gpio_2 { + janice_cfg1 { + pins = "GPIO201_AF24", "GPIO202_AF25"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based I2C bus for the NFC */ + i2c-gpio-3 { + i2c_gpio_3_default: i2c_gpio_3 { + janice_cfg1 { + pins = "GPIO151_D17", "GPIO152_D16"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + /* GPIO-based SPI bus for the display */ + spi-gpio-0 { + spi_gpio_0_default: spi_gpio_0 { + janice_cfg1 { + pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9"; + ste,config = <&gpio_out_hi>; + }; + /* This pin is unused but belongs with this SPI block */ + janice_cfg2 { + pins = "GPIO225_AG8"; + ste,config = <&in_pd>; + }; + }; + }; + wlan { + wlan_default_mode: wlan_default { + /* GPIO215 used for RESET_N */ + janice_cfg1 { + pins = "GPIO215_AH13"; + ste,config = <&gpio_out_lo>; + }; + /* GPIO216 for WL_HOST_WAKE */ + janice_cfg2 { + pins = "GPIO216_AG12"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + bluetooth { + bluetooth_default_mode: bluetooth_default { + janice_cfg1 { + pins = "GPIO199_AH23"; + ste,config = <&gpio_out_lo>; + }; + janice_cfg2 { + pins = "GPIO97_D9"; + ste,config = <&gpio_in_nopull>; + }; + janice_cfg3 { + pins = "GPIO209_AG15"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + /* Interrupt line for TI TSU6111 Micro USB switch */ + tsu6111 { + tsu6111_janice_default: tsu6111_janice { + janice_cfg1 { + /* GPIO95 used for IRQ */ + pins = "GPIO95_E8"; + ste,config = <&gpio_in_nopull>; + }; + }; + }; + nfc { + pn547_janice_default: pn547_janice { + /* Interrupt line */ + janice_cfg1 { + pins = "GPIO32_V2"; + ste,config = <&gpio_in_nopull>; + }; + /* Enable and firmware GPIOs */ + janice_cfg2 { + pins = "GPIO31_V3", "GPIO88_C4"; + ste,config = <&gpio_out_lo>; + }; + }; + }; +}; From 200231a7270692576db0c9fe38af6b0030f03426 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 8 Dec 2020 22:06:24 +0100 Subject: [PATCH 191/584] ARM: dts: ux500: Fix channel names attributes The AB8500/AB8505 is providing ADC channels and do so using the standard property "io-channel-names" not the mistakenly singular form "io-channel-name". Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-ab8500.dtsi | 8 ++++---- arch/arm/boot/dts/ste-ab8505.dtsi | 6 +++--- 2 files changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi index 4c16736ea789..fd9f068df5e3 100644 --- a/arch/arm/boot/dts/ste-ab8500.dtsi +++ b/arch/arm/boot/dts/ste-ab8500.dtsi @@ -124,7 +124,7 @@ compatible = "stericsson,abx500-temp"; io-channels = <&gpadc 0x06>, <&gpadc 0x07>; - io-channel-name = "aux1", "aux2"; + io-channel-names = "aux1", "aux2"; }; ab8500_battery: ab8500_battery { @@ -136,7 +136,7 @@ compatible = "stericsson,ab8500-fg"; battery = <&ab8500_battery>; io-channels = <&gpadc 0x08>; - io-channel-name = "main_bat_v"; + io-channel-names = "main_bat_v"; }; ab8500_btemp { @@ -144,7 +144,7 @@ battery = <&ab8500_battery>; io-channels = <&gpadc 0x02>, <&gpadc 0x01>; - io-channel-name = "btemp_ball", + io-channel-names = "btemp_ball", "bat_ctrl"; }; @@ -156,7 +156,7 @@ <&gpadc 0x0a>, <&gpadc 0x09>, <&gpadc 0x0b>; - io-channel-name = "main_charger_v", + io-channel-names = "main_charger_v", "main_charger_c", "vbus_v", "usb_charger_c"; diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi index c72aa250bf6f..64f7e4332053 100644 --- a/arch/arm/boot/dts/ste-ab8505.dtsi +++ b/arch/arm/boot/dts/ste-ab8505.dtsi @@ -99,7 +99,7 @@ compatible = "stericsson,ab8500-fg"; battery = <&ab8500_battery>; io-channels = <&gpadc 0x08>; - io-channel-name = "main_bat_v"; + io-channel-names = "main_bat_v"; }; ab8500_btemp { @@ -108,7 +108,7 @@ battery = <&ab8500_battery>; io-channels = <&gpadc 0x02>, <&gpadc 0x01>; - io-channel-name = "btemp_ball", + io-channel-names = "btemp_ball", "bat_ctrl"; }; @@ -119,7 +119,7 @@ vddadc-supply = <&ab8500_ldo_adc_reg>; io-channels = <&gpadc 0x09>, <&gpadc 0x0b>; - io-channel-name = "vbus_v", + io-channel-names = "vbus_v", "usb_charger_c"; }; From bc324d447fba56e9c6a2aef4da24194727ea0f59 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Thu, 10 Dec 2020 16:17:21 +0100 Subject: [PATCH 192/584] ARM: dts: ux500: Add interrupts to charger The different charger nodes in the AB8500 and AB8505 includes was missing the interrupt assignments for the interrupts necessary to drive the AB8500/AB8505 charging state machine. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-ab8500.dtsi | 56 +++++++++++++++++++++++++++++-- arch/arm/boot/dts/ste-ab8505.dtsi | 48 ++++++++++++++++++++++++++ 2 files changed, 101 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi index fd9f068df5e3..4fd09997a2b9 100644 --- a/arch/arm/boot/dts/ste-ab8500.dtsi +++ b/arch/arm/boot/dts/ste-ab8500.dtsi @@ -122,6 +122,8 @@ ab8500_temp { compatible = "stericsson,abx500-temp"; + interrupts = <3 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "ABX500_TEMP_WARM"; io-channels = <&gpadc 0x06>, <&gpadc 0x07>; io-channel-names = "aux1", "aux2"; @@ -134,14 +136,34 @@ ab8500_fg { compatible = "stericsson,ab8500-fg"; - battery = <&ab8500_battery>; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>, + <8 IRQ_TYPE_LEVEL_HIGH>, + <28 IRQ_TYPE_LEVEL_HIGH>, + <27 IRQ_TYPE_LEVEL_HIGH>, + <26 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "NCONV_ACCU", + "BATT_OVV", + "LOW_BAT_F", + "CC_INT_CALIB", + "CCEOC"; + battery = <&ab8500_battery>; io-channels = <&gpadc 0x08>; io-channel-names = "main_bat_v"; }; ab8500_btemp { compatible = "stericsson,ab8500-btemp"; - battery = <&ab8500_battery>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>, + <80 IRQ_TYPE_LEVEL_HIGH>, + <83 IRQ_TYPE_LEVEL_HIGH>, + <81 IRQ_TYPE_LEVEL_HIGH>, + <82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "BAT_CTRL_INDB", + "BTEMP_LOW", + "BTEMP_HIGH", + "BTEMP_LOW_MEDIUM", + "BTEMP_MEDIUM_HIGH"; + battery = <&ab8500_battery>; io-channels = <&gpadc 0x02>, <&gpadc 0x01>; io-channel-names = "btemp_ball", @@ -149,7 +171,35 @@ }; ab8500_charger { - compatible = "stericsson,ab8500-charger"; + compatible = "stericsson,ab8500-charger"; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <11 IRQ_TYPE_LEVEL_HIGH>, + <0 IRQ_TYPE_LEVEL_HIGH>, + <107 IRQ_TYPE_LEVEL_HIGH>, + <106 IRQ_TYPE_LEVEL_HIGH>, + <14 IRQ_TYPE_LEVEL_HIGH>, + <15 IRQ_TYPE_LEVEL_HIGH>, + <79 IRQ_TYPE_LEVEL_HIGH>, + <105 IRQ_TYPE_LEVEL_HIGH>, + <104 IRQ_TYPE_LEVEL_HIGH>, + <89 IRQ_TYPE_LEVEL_HIGH>, + <22 IRQ_TYPE_LEVEL_HIGH>, + <21 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "MAIN_CH_UNPLUG_DET", + "MAIN_CHARGE_PLUG_DET", + "MAIN_EXT_CH_NOT_OK", + "MAIN_CH_TH_PROT_R", + "MAIN_CH_TH_PROT_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_CH_TH_PROT_R", + "USB_CH_TH_PROT_F", + "USB_CHARGER_NOT_OKR", + "VBUS_OVV", + "CH_WD_EXP", + "VBUS_CH_DROP_END"; battery = <&ab8500_battery>; vddadc-supply = <&ab8500_ldo_tvout_reg>; io-channels = <&gpadc 0x03>, diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi index 64f7e4332053..17854b215eda 100644 --- a/arch/arm/boot/dts/ste-ab8505.dtsi +++ b/arch/arm/boot/dts/ste-ab8505.dtsi @@ -97,6 +97,16 @@ ab8500_fg { status = "disabled"; compatible = "stericsson,ab8500-fg"; + interrupts = <24 IRQ_TYPE_LEVEL_HIGH>, + <8 IRQ_TYPE_LEVEL_HIGH>, + <28 IRQ_TYPE_LEVEL_HIGH>, + <27 IRQ_TYPE_LEVEL_HIGH>, + <26 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "NCONV_ACCU", + "BATT_OVV", + "LOW_BAT_F", + "CC_INT_CALIB", + "CCEOC"; battery = <&ab8500_battery>; io-channels = <&gpadc 0x08>; io-channel-names = "main_bat_v"; @@ -105,6 +115,16 @@ ab8500_btemp { status = "disabled"; compatible = "stericsson,ab8500-btemp"; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH>, + <80 IRQ_TYPE_LEVEL_HIGH>, + <83 IRQ_TYPE_LEVEL_HIGH>, + <81 IRQ_TYPE_LEVEL_HIGH>, + <82 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "BAT_CTRL_INDB", + "BTEMP_LOW", + "BTEMP_HIGH", + "BTEMP_LOW_MEDIUM", + "BTEMP_MEDIUM_HIGH"; battery = <&ab8500_battery>; io-channels = <&gpadc 0x02>, <&gpadc 0x01>; @@ -115,6 +135,34 @@ ab8500_charger { status = "disabled"; compatible = "stericsson,ab8500-charger"; + interrupts = <10 IRQ_TYPE_LEVEL_HIGH>, + <11 IRQ_TYPE_LEVEL_HIGH>, + <0 IRQ_TYPE_LEVEL_HIGH>, + <107 IRQ_TYPE_LEVEL_HIGH>, + <106 IRQ_TYPE_LEVEL_HIGH>, + <14 IRQ_TYPE_LEVEL_HIGH>, + <15 IRQ_TYPE_LEVEL_HIGH>, + <79 IRQ_TYPE_LEVEL_HIGH>, + <105 IRQ_TYPE_LEVEL_HIGH>, + <104 IRQ_TYPE_LEVEL_HIGH>, + <89 IRQ_TYPE_LEVEL_HIGH>, + <22 IRQ_TYPE_LEVEL_HIGH>, + <21 IRQ_TYPE_LEVEL_HIGH>, + <16 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "MAIN_CH_UNPLUG_DET", + "MAIN_CHARGE_PLUG_DET", + "MAIN_EXT_CH_NOT_OK", + "MAIN_CH_TH_PROT_R", + "MAIN_CH_TH_PROT_F", + "VBUS_DET_F", + "VBUS_DET_R", + "USB_LINK_STATUS", + "USB_CH_TH_PROT_R", + "USB_CH_TH_PROT_F", + "USB_CHARGER_NOT_OKR", + "VBUS_OVV", + "CH_WD_EXP", + "VBUS_CH_DROP_END"; battery = <&ab8500_battery>; vddadc-supply = <&ab8500_ldo_adc_reg>; io-channels = <&gpadc 0x09>, From 695055861a361bc6ec14b584f44a3c0c453633a5 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sat, 12 Dec 2020 11:46:26 +0100 Subject: [PATCH 193/584] ARM: dts: ux500: Add thermistors to the HREF This adds the two temperature-monitoring thermistors to the HREF reference design, defines a thermal zone for the chassis and sets some reasonable thermal limits. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-hrefv60plus.dtsi | 58 ++++++++++++++++++++++++++ 1 file changed, 58 insertions(+) diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index 05b4fbbba57f..ee0bf00a94b8 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -10,6 +10,64 @@ model = "ST-Ericsson HREF (v60+) platform with Device Tree"; compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; + thermal-zones { + chassis-thermal { + /* Poll every 20 seconds */ + polling-delay = <20000>; + /* Poll every 2nd second when cooling */ + polling-delay-passive = <2000>; + + thermal-sensors = <&therm1>, <&therm2>; + + /* Tripping points made from rough guess about operating conditions */ + trips { + chassis_alert: chassis-alert { + /* At 50 degrees take down the CPU frequency */ + temperature = <50000>; + hysteresis = <3000>; + type = "active"; + }; + chassis_crit: chassis-crit { + /* Just shut down at 70 degrees */ + temperature = <70000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + /* Push down the operating frequency of the SoC when it gets hot */ + cooling-maps { + map0 { + trip = <&chassis_alert>; + cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + contribution = <100>; + }; + }; + }; + }; + + /* + * Thermistors on the board, formally to monitor battery temperatures + * but what they measure is the board temperature. + */ + therm1: thermistor@0 { + compatible = "murata,ncp18wb473"; + io-channels = <&gpadc 0x06>; /* AUX1 */ + pullup-uv = <1800000>; + pullup-ohm = <220000>; + pulldown-ohm = <0>; + #thermal-sensor-cells = <0>; + }; + + therm2: thermistor@1 { + compatible = "murata,ncp18wb473"; + io-channels = <&gpadc 0x07>; /* AUX2 */ + pullup-uv = <1800000>; + pullup-ohm = <220000>; + pulldown-ohm = <0>; + #thermal-sensor-cells = <0>; + }; + soc { /* Name the GPIO muxed rails on the HREF boards */ gpio@8012e000 { From ace79dd1b0d99a3789809d94a00d230d76f61c57 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 18 Dec 2020 23:20:50 +0100 Subject: [PATCH 194/584] ARM: dts: ux500: Remove the GPADC HW IRQ The AB8505 variant lacks the hardware conversion IRQ, so do not put it in with this variant. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-ab8505.dtsi | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi index 17854b215eda..696e6691fe41 100644 --- a/arch/arm/boot/dts/ste-ab8505.dtsi +++ b/arch/arm/boot/dts/ste-ab8505.dtsi @@ -45,9 +45,8 @@ gpadc: ab8500-gpadc { compatible = "stericsson,ab8500-gpadc"; - interrupts = <32 IRQ_TYPE_LEVEL_HIGH - 39 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "HW_CONV_END", "SW_CONV_END"; + interrupts = <39 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "SW_CONV_END"; vddadc-supply = <&ab8500_ldo_adc_reg>; #address-cells = <1>; #size-cells = <0>; @@ -90,7 +89,7 @@ }; ab8500_battery: ab8500_battery { - status = "disabled"; + stericsson,battery-type = "LIPO"; thermistor-on-batctrl; }; From 5282da459a97640ad2d12029665fa8c0a09d72a2 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sat, 19 Dec 2020 21:31:55 +0100 Subject: [PATCH 195/584] ARM: dts: ux500: Push VMMCI down to each tree The setting of VMMCI differs so much between different boards that we need to handle it on a per-board basis rather that complicating things by overriding stuff from the included DTSI:s. Push it down into top-level tree instead. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-href.dtsi | 15 -------- arch/arm/boot/dts/ste-href520-tvk.dts | 42 ++++++++++++++++++--- arch/arm/boot/dts/ste-hrefprev60-stuib.dts | 19 ++++++++++ arch/arm/boot/dts/ste-hrefprev60-tvk.dts | 19 ++++++++++ arch/arm/boot/dts/ste-hrefprev60.dtsi | 6 --- arch/arm/boot/dts/ste-hrefv60plus-stuib.dts | 39 +++++++++++++++++++ arch/arm/boot/dts/ste-hrefv60plus-tvk.dts | 39 +++++++++++++++++++ arch/arm/boot/dts/ste-hrefv60plus.dtsi | 16 -------- 8 files changed, 153 insertions(+), 42 deletions(-) diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index ff47cbf6ed3b..8c03124b6960 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -113,21 +113,6 @@ status = "okay"; }; - /* ST6G3244ME level translator for 1.8/2.9 V */ - vmmci: regulator-gpio { - compatible = "regulator-gpio"; - - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <2900000>; - regulator-name = "mmci-reg"; - regulator-type = "voltage"; - - startup-delay-us = <100>; - - states = <1800000 0x1 - 2900000 0x0>; - }; - // External Micro SD slot sdi0_per1@80126000 { arm,primecell-periphid = <0x10480180>; diff --git a/arch/arm/boot/dts/ste-href520-tvk.dts b/arch/arm/boot/dts/ste-href520-tvk.dts index f8c0c1e6aa04..a036a03f6718 100644 --- a/arch/arm/boot/dts/ste-href520-tvk.dts +++ b/arch/arm/boot/dts/ste-href520-tvk.dts @@ -12,11 +12,43 @@ model = "ST-Ericsson HREF520 and TVK1281618 UIB"; compatible = "st-ericsson,href520", "st-ericsson,u8500"; - soc { - vmmci: regulator-gpio { - gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; - enable-gpio = <&gpio2 14 GPIO_ACTIVE_HIGH>; - enable-active-high; + + /* ST6G3244ME level translator for 1.8/2.9 V */ + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + + states = <1800000 0x1 + 2900000 0x0>; + + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio2 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&vmmci_default_mode>; + }; +}; + +&pinctrl { + vmmci { + vmmci_default_mode: vmmc_default { + /* VMMCI level-shifter enable */ + default_href520_cfg1 { + pins = "GPIO78_F4"; + ste,config = <&gpio_out_hi>; + }; + /* VMMCI level-shifter voltage select */ + default_href520_cfg2 { + pins = "GPIO5_AG6"; + ste,config = <&gpio_out_hi>; + }; }; }; }; diff --git a/arch/arm/boot/dts/ste-hrefprev60-stuib.dts b/arch/arm/boot/dts/ste-hrefprev60-stuib.dts index 8ce6b723abf2..dfc933214c1a 100644 --- a/arch/arm/boot/dts/ste-hrefprev60-stuib.dts +++ b/arch/arm/boot/dts/ste-hrefprev60-stuib.dts @@ -12,6 +12,25 @@ model = "ST-Ericsson HREF (pre-v60) and ST UIB"; compatible = "st-ericsson,mop500", "st-ericsson,u8500"; + /* ST6G3244ME level translator for 1.8/2.9 V */ + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + + states = <1800000 0x1 + 2900000 0x0>; + + gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>; + enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + soc { /* Reset line for the BU21013 touchscreen */ i2c@80110000 { diff --git a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts index 142f5475521f..4e6e4439dcff 100644 --- a/arch/arm/boot/dts/ste-hrefprev60-tvk.dts +++ b/arch/arm/boot/dts/ste-hrefprev60-tvk.dts @@ -11,4 +11,23 @@ / { model = "ST-Ericsson HREF (pre-v60) and TVK1281618 UIB"; compatible = "st-ericsson,mop500", "st-ericsson,u8500"; + + /* ST6G3244ME level translator for 1.8/2.9 V */ + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + + states = <1800000 0x1 + 2900000 0x0>; + + gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>; + enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; }; diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi index 115495de8612..931998dd364b 100644 --- a/arch/arm/boot/dts/ste-hrefprev60.dtsi +++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi @@ -65,12 +65,6 @@ cd-gpios = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>; }; - vmmci: regulator-gpio { - gpios = <&tc3589x_gpio 18 GPIO_ACTIVE_HIGH>; - enable-gpio = <&tc3589x_gpio 17 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - pinctrl { /* Set this up using hogs */ pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts index 1316886e6bcb..52c56ed17ae6 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts +++ b/arch/arm/boot/dts/ste-hrefv60plus-stuib.dts @@ -14,6 +14,28 @@ model = "ST-Ericsson HREF (v60+) and ST UIB"; compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; + /* ST6G3244ME level translator for 1.8/2.9 V */ + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + + states = <1800000 0x1 + 2900000 0x0>; + + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&vmmci_default_mode>; + }; + soc { /* Reset line for the BU21013 touchscreen */ i2c@80110000 { @@ -33,3 +55,20 @@ }; }; }; + +&pinctrl { + vmmci { + vmmci_default_mode: vmmc_default { + /* VMMCI level-shifter enable */ + default_hrefv60_cfg2 { + pins = "GPIO169_D22"; + ste,config = <&gpio_out_hi>; + }; + /* VMMCI level-shifter voltage select */ + default_hrefv60_cfg3 { + pins = "GPIO5_AG6"; + ste,config = <&gpio_out_hi>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts index 5d4b8245f02c..9c2d2ee6d6d8 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts +++ b/arch/arm/boot/dts/ste-hrefv60plus-tvk.dts @@ -13,4 +13,43 @@ / { model = "ST-Ericsson HREF (v60+) and TVK1281618 UIB"; compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; + + /* ST6G3244ME level translator for 1.8/2.9 V */ + vmmci: regulator-gpio { + compatible = "regulator-gpio"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2900000>; + regulator-name = "mmci-reg"; + regulator-type = "voltage"; + + startup-delay-us = <100>; + + states = <1800000 0x1 + 2900000 0x0>; + + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-names = "default"; + pinctrl-0 = <&vmmci_default_mode>; + }; +}; + +&pinctrl { + vmmci { + vmmci_default_mode: vmmc_default { + /* VMMCI level-shifter enable */ + default_hrefv60_cfg2 { + pins = "GPIO169_D22"; + ste,config = <&gpio_out_hi>; + }; + /* VMMCI level-shifter voltage select */ + default_hrefv60_cfg3 { + pins = "GPIO5_AG6"; + ste,config = <&gpio_out_hi>; + }; + }; + }; }; diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index ee0bf00a94b8..05ea12e6df1c 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -194,12 +194,6 @@ cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95 }; - vmmci: regulator-gpio { - gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; - enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - pinctrl { /* * Set this up using hogs, as time goes by and as seems fit, these @@ -224,16 +218,6 @@ pins = "GPIO95_E8"; ste,config = <&gpio_in_pu>; }; - /* VMMCI level-shifter enable */ - default_hrefv60_cfg2 { - pins = "GPIO169_D22"; - ste,config = <&gpio_out_hi>; - }; - /* VMMCI level-shifter voltage select */ - default_hrefv60_cfg3 { - pins = "GPIO5_AG6"; - ste,config = <&gpio_out_hi>; - }; }; }; ipgpio { From 7ac9266120bc065c0ce6e924867fdbc976671897 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 21 Dec 2020 13:20:26 +0100 Subject: [PATCH 196/584] ARM: dts: ux500: Add die temperature to AB8505 The AB8505 mixed signal ASIC variant has a die temperature channel that is missing in the AB8500 variant. Add it to the DTSI. Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-ab8505.dtsi | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi index 696e6691fe41..cc045b2fc217 100644 --- a/arch/arm/boot/dts/ste-ab8505.dtsi +++ b/arch/arm/boot/dts/ste-ab8505.dtsi @@ -13,7 +13,8 @@ <&gpadc 0x08>, /* Main battery voltage */ <&gpadc 0x09>, /* VBUS */ <&gpadc 0x0b>, /* Charger current */ - <&gpadc 0x0c>; /* Backup battery voltage */ + <&gpadc 0x0c>, /* Backup battery voltage */ + <&gpadc 0x0d>; /* Die temperature */ }; soc { @@ -83,6 +84,9 @@ bk_bat_v: channel@0c { reg = <0x0c>; }; + die_temp: channel@0d { + reg = <0x0d>; + }; usb_id: channel@0e { reg = <0x0e>; }; From 73feebad9e056cfe5f444acd5b61f3d0d5ec74bb Mon Sep 17 00:00:00 2001 From: Ulrich Hecht Date: Tue, 12 Jan 2021 17:59:48 +0100 Subject: [PATCH 197/584] arm64: dts: renesas: r8a779a0: Add pinctrl device node This patch adds the pinctrl device node for the R8A779A0 (V3U) SoC. Signed-off-by: Ulrich Hecht Link: https://lore.kernel.org/r/20210112165948.31162-1-uli+renesas@fpond.eu Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index f951e6b6f696..6ac2c9d37acd 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -80,6 +80,15 @@ status = "disabled"; }; + pfc: pin-controller@e6050000 { + compatible = "renesas,pfc-r8a779a0"; + reg = <0 0xe6050000 0 0x16c>, <0 0xe6050800 0 0x16c>, + <0 0xe6058000 0 0x16c>, <0 0xe6058800 0 0x16c>, + <0 0xe6060000 0 0x16c>, <0 0xe6060800 0 0x16c>, + <0 0xe6068000 0 0x16c>, <0 0xe6068800 0 0x16c>, + <0 0xe6069000 0 0x16c>, <0 0xe6069800 0 0x16c>; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a779a0-cpg-mssr"; reg = <0 0xe6150000 0 0x4000>; From dfacaef96cbf871be23b4e2613818a9658f23817 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 14 Jan 2021 12:11:17 +0100 Subject: [PATCH 198/584] arm64: dts: renesas: r8a779a0: Add GPIO nodes Add device nodes for the General Purpose Input/Output (GPIO) block on the Renesas R-Car V3U (r8a779a0) SoC. Signed-off-by: Geert Uytterhoeven Tested-by: Wolfram Sang Link: https://lore.kernel.org/r/20210114111117.2214281-1-geert+renesas@glider.be --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 140 ++++++++++++++++++++++ 1 file changed, 140 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 6ac2c9d37acd..66b47a848443 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -89,6 +89,146 @@ <0 0xe6069000 0 0x16c>, <0 0xe6069800 0 0x16c>; }; + gpio0: gpio@e6058180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6058180 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 916>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 916>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 0 28>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio@e6050180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6050180 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 915>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 915>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 32 31>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@e6050980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6050980 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 915>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 915>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 64 25>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@e6058980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6058980 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 916>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 916>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 96 17>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@e6060180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6060180 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 917>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 917>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 128 27>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio5: gpio@e6060980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6060980 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 917>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 917>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 160 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio6: gpio@e6068180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6068180 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 192 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio7: gpio@e6068980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6068980 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 224 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio8: gpio@e6069180 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6069180 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 256 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio9: gpio@e6069980 { + compatible = "renesas,gpio-r8a779a0"; + reg = <0 0xe6069980 0 0x54>; + interrupts = ; + clocks = <&cpg CPG_MOD 918>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 918>; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pfc 0 288 21>; + interrupt-controller; + #interrupt-cells = <2>; + }; + cpg: clock-controller@e6150000 { compatible = "renesas,r8a779a0-cpg-mssr"; reg = <0 0xe6150000 0 0x4000>; From 1f4449e12c5c6682a6f4f8dbc7288c19c1c844f1 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 7 Jan 2021 19:20:45 +0100 Subject: [PATCH 199/584] arm64: dts: renesas: r8a779a0: Add SYS-DMAC nodes Add device nodes for the Direct Memory Access Controller for System (SYS-DMAC) instances on the Renesas R-Car V3U (r8a779a0) SoC. Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20210107182045.1948037-1-geert+renesas@glider.be --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 58 +++++++++++++++++++++++ 1 file changed, 58 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 66b47a848443..3bc15592d000 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -264,6 +264,64 @@ status = "disabled"; }; + dmac1: dma-controller@e7350000 { + compatible = "renesas,dmac-r8a779a0"; + reg = <0 0xe7350000 0 0x1000>, + <0 0xe7300000 0 0x10000>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", "ch4", + "ch5", "ch6", "ch7", "ch8", "ch9", + "ch10", "ch11", "ch12", "ch13", + "ch14", "ch15"; + clocks = <&cpg CPG_MOD 709>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 709>; + #dma-cells = <1>; + dma-channels = <16>; + }; + + dmac2: dma-controller@e7351000 { + compatible = "renesas,dmac-r8a779a0"; + reg = <0 0xe7351000 0 0x1000>, + <0 0xe7310000 0 0x10000>; + interrupts = , + , + , + , + , + , + , + , + ; + interrupt-names = "error", + "ch0", "ch1", "ch2", "ch3", "ch4", + "ch5", "ch6", "ch7"; + clocks = <&cpg CPG_MOD 710>; + clock-names = "fck"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 710>; + #dma-cells = <1>; + dma-channels = <8>; + }; + gic: interrupt-controller@f1000000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; From cc72570747e43335f4933a24dd74d5653639176a Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:23 +0000 Subject: [PATCH 200/584] arm64: dts: allwinner: A64: properly connect USB PHY to port 0 In recent Allwinner SoCs the first USB host controller (HCI0) shares the first PHY with the MUSB controller. Probably to make this sharing work, we were avoiding to declare this in the DT. This has two shortcomings: - U-Boot (which uses the same .dts) cannot use this port in host mode without a PHY linked, so we were loosing one USB port there. - It requires the MUSB driver to be enabled and loaded, although we don't actually use it. To avoid those issues, let's add this PHY link to the A64 .dtsi file. After all PHY port 0 *is* connected to HCI0, so we should describe it as this. Remove the part from the Pinebook DTS which already had this property. This makes it work in U-Boot, also improves compatiblity when no MUSB driver is loaded (for instance in distribution installers). Fixes: dc03a047df1d ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI") Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 4 ---- arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 4 ++++ 2 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index 896f34fd9fc3..d07cf05549c3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -126,8 +126,6 @@ }; &ehci0 { - phys = <&usbphy 0>; - phy-names = "usb"; status = "okay"; }; @@ -177,8 +175,6 @@ }; &ohci0 { - phys = <&usbphy 0>; - phy-names = "usb"; status = "okay"; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 51cc30e84e26..19e9b8ca8432 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -593,6 +593,8 @@ <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>, <&ccu RST_BUS_EHCI0>; + phys = <&usbphy 0>; + phy-names = "usb"; status = "disabled"; }; @@ -603,6 +605,8 @@ clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>; + phys = <&usbphy 0>; + phy-names = "usb"; status = "disabled"; }; From da2fb8457f71138d455cba82edec0d34f858e506 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:24 +0000 Subject: [PATCH 201/584] arm64: dts: allwinner: H6: properly connect USB PHY to port 0 In recent Allwinner SoCs the first USB host controller (HCI0) shares the first PHY with the MUSB controller. Probably to make this sharing work, we were avoiding to declare this in the DT. This has two shortcomings: - U-Boot (which uses the same .dts) cannot use this port in host mode without a PHY linked, so we were loosing one USB port there. - It requires the MUSB driver to be enabled and loaded, although we don't actually use it. To avoid those issues, let's add this PHY link to the H6 .dtsi file. After all PHY port 0 *is* connected to HCI0, so we should describe it as this. This makes it work in U-Boot, also improves compatiblity when no MUSB driver is loaded (for instance in distribution installers). Fixes: eabb3d424b6d ("arm64: dts: allwinner: h6: add USB2-related device nodes") Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 8a62a9fbe347..f593cfeaecc9 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -680,6 +680,8 @@ <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>, <&ccu RST_BUS_EHCI0>; + phys = <&usb2phy 0>; + phy-names = "usb"; status = "disabled"; }; @@ -690,6 +692,8 @@ clocks = <&ccu CLK_BUS_OHCI0>, <&ccu CLK_USB_OHCI0>; resets = <&ccu RST_BUS_OHCI0>; + phys = <&usb2phy 0>; + phy-names = "usb"; status = "disabled"; }; From 66a3cf5a25e2d62c8ff3b9344a50419379b01bc6 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:25 +0000 Subject: [PATCH 202/584] arm64: dts: allwinner: Pine64-LTS: Add status LED The Pine64-LTS board features a blue status LED on pin PL7. Describe it in the DT. Signed-off-by: Andre Przywara Tested-by: Heinrich Schuchardt Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-4-andre.przywara@arm.com --- .../boot/dts/allwinner/sun50i-a64-pine64-lts.dts | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts index 302e24be0a31..437ffe3628a5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pine64-lts.dts @@ -1,10 +1,21 @@ // SPDX-License-Identifier: (GPL-2.0+ OR MIT) // Copyright (c) 2018 ARM Ltd. +#include #include "sun50i-a64-sopine-baseboard.dts" / { model = "Pine64 LTS"; compatible = "pine64,pine64-lts", "allwinner,sun50i-r18", "allwinner,sun50i-a64"; + + leds { + compatible = "gpio-leds"; + + led { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */ + }; + }; }; From 941432d007689f3774646e41a1439228b6c6ee0e Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:26 +0000 Subject: [PATCH 203/584] arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card The SD card on the SoPine SoM module is somewhat concealed, so was originally defined as "non-removable". However there is a working card-detect pin (tested on two different SoM versions), and in certain SoM base boards it might be actually accessible at runtime. Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the non-removable flag, even though the SD card slot is perfectly accessible and usable there. (It turns out that just *my* board has a broken card detect switch, so I originally thought CD wouldn't work on the LTS.) Drop the "non-removable" flag to describe the SD card slot properly. Fixes: c3904a269891 ("arm64: allwinner: a64: add DTSI file for SoPine SoM") Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi index c48692b06e1f..3402cec87035 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine.dtsi @@ -32,7 +32,6 @@ pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; vmmc-supply = <®_dcdc1>; - non-removable; disable-wp; bus-width = <4>; cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ From cfe6c487b9a1abc6197714ec5605716a5428cf03 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:27 +0000 Subject: [PATCH 204/584] arm64: dts: allwinner: H6: Allow up to 150 MHz MMC bus frequency The H6 manual explicitly lists a frequency limit of 150 MHz for the bus frequency of the MMC controllers. So far we had no explicit limits in the DT, which limited eMMC to the spec defined frequencies, or whatever the driver defines (both Linux and FreeBSD use 52 MHz here). Put those maximum frequencies in the SoC .dtsi, to allow higher speed modes (which still would need to be explicitly enabled, per board). Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed 200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably. Fixes: 8f54bd1595b3 ("arm64: allwinner: h6: add device tree nodes for MMC controllers") Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index f593cfeaecc9..77765d4a05ec 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -436,6 +436,7 @@ interrupts = ; pinctrl-names = "default"; pinctrl-0 = <&mmc0_pins>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -452,6 +453,7 @@ interrupts = ; pinctrl-names = "default"; pinctrl-0 = <&mmc1_pins>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -468,6 +470,7 @@ interrupts = ; pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; From 948c657cc45e8ce48cb533d4e2106145fa765759 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:28 +0000 Subject: [PATCH 205/584] arm64: dts: allwinner: A64: Limit MMC2 bus frequency to 150 MHz In contrast to the H6 (and later) manuals, the A64 datasheet does not specify any limitations in the maximum possible frequency for eMMC controllers. However experimentation has found that a 150 MHz limit similar to other SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist for the MMC2 controller. Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi. The Pinebook seems to be the an odd exception, since it apparently seems to work with 200 MHz as well, so overwrite this in its board .dts file. Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works. Fixes: 22be992faea7 ("arm64: allwinner: a64: Increase the MMC max frequency") Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts | 1 + arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi | 2 +- 2 files changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts index d07cf05549c3..7ae16541d14f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts @@ -167,6 +167,7 @@ pinctrl-0 = <&mmc2_pins>, <&mmc2_ds_pin>; vmmc-supply = <®_dcdc1>; vqmmc-supply = <®_eldo1>; + max-frequency = <200000000>; bus-width = <8>; non-removable; cap-mmc-hw-reset; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi index 19e9b8ca8432..57786fc120c3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi @@ -514,7 +514,7 @@ resets = <&ccu RST_BUS_MMC2>; reset-names = "ahb"; interrupts = ; - max-frequency = <200000000>; + max-frequency = <150000000>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; From 0d66e0b857c6bd3f7c6a481ed40a1de05fe17b66 Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:29 +0000 Subject: [PATCH 206/584] arm64: dts: allwinner: Pine64-LTS/SoPine: Enable HS200 eMMC mode The eMMC modules offered for the Pine64 boards are capable of the HS200 eMMC speed mode, when observing the frequency limit of 150 MHz. Enable that in the DT. This increases the interface speed from ~80 MB/s to ~120 MB/s. Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-8-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts index d4069749d721..e22b94c83647 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-sopine-baseboard.dts @@ -111,6 +111,7 @@ bus-width = <8>; non-removable; cap-mmc-hw-reset; + mmc-hs200-1_8v; status = "okay"; }; From 8837e845a2a89c2097819898b83663987f9c89fe Mon Sep 17 00:00:00 2001 From: Andre Przywara Date: Wed, 13 Jan 2021 15:26:30 +0000 Subject: [PATCH 207/584] arm64: dts: allwinner: Pine H64: Enable HS200 eMMC mode The eMMC modules offered for the Pine64 boards are capable of the HS200 eMMC speed mode, when observing the frequency limit of 150 MHz. Enable that in the DT. This increases the interface speed from ~80 MB/s to ~120 MB/s. Signed-off-by: Andre Przywara Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210113152630.28810-9-andre.przywara@arm.com --- arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts index 961732c52aa0..15ceba027a73 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts @@ -142,6 +142,7 @@ vqmmc-supply = <®_bldo2>; non-removable; cap-mmc-hw-reset; + mmc-hs200-1_8v; bus-width = <8>; status = "okay"; }; From eb6f3655d3ed4ee093b484b7a7246a61ae2bc30f Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Mon, 11 Jan 2021 12:45:52 -0600 Subject: [PATCH 208/584] arm64: dts: ti: k3-j7200: Add R5F cluster nodes The J7200 SoCs have 2 dual-core Arm Cortex-R5F processor (R5FSS) subsystems/clusters. One R5F cluster is present within the MCU domain (MCU_R5FSS0), and the other one is present within the MAIN domain (MAIN_R5FSS0). Each of these can be configured at boot time to be either run in a LockStep mode or in an Asymmetric Multi Processing (AMP) fashion in Split-mode. These subsystems have 64 KB each Tightly-Coupled Memory (TCM) internal memories for each core split between two banks - ATCM and BTCM (further interleaved into two banks). The TCMs of both Cores are combined in LockStep-mode to provide a larger 128 KB of memory, but otherwise are functionally similar to those on J721E SoCs. Add the DT nodes for both the MCU and MAIN domain R5F cluster/subsystems, the two R5F cores are added as child nodes to each of the R5F cluster nodes. The clusters are configured to run in LockStep mode by default, with the ATCMs enabled to allow the R5 cores to execute code from DDR with boot-strapping code from ATCM. The inter-processor communication between the main A72 cores and these processors is achieved through shared memory and Mailboxes. The following firmware names are used by default for these cores, and can be overridden in a board dts file if desired: MCU R5FSS0 Core0: j7200-mcu-r5f0_0-fw (both in LockStep and Split modes) MCU R5FSS0 Core1: j7200-mcu-r5f0_1-fw (needed only in Split mode) MAIN R5FSS0 Core0: j7200-main-r5f0_0-fw (both in LockStep & Split modes) MAIN R5FSS0 Core1: j7200-main-r5f0_1-fw (needed only in Split mode) Signed-off-by: Suman Anna Signed-off-by: Nishanth Menon Reviewed-by: Lokesh Vutla Link: https://lore.kernel.org/r/20210111184554.6748-2-s-anna@ti.com --- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 42 ++++++++++++++++++- .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi | 42 ++++++++++++++++++- 2 files changed, 82 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index 4e39f0325c03..4cc2e9094d0e 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -2,7 +2,7 @@ /* * Device Tree Source for J7200 SoC Family Main Domain peripherals * - * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ / { @@ -671,4 +671,44 @@ dr_mode = "otg"; }; }; + + main_r5fss0: r5fss@5c00000 { + compatible = "ti,j7200-r5fss"; + ti,cluster-mode = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x5c00000 0x00 0x5c00000 0x20000>, + <0x5d00000 0x00 0x5d00000 0x20000>; + power-domains = <&k3_pds 243 TI_SCI_PD_EXCLUSIVE>; + + main_r5fss0_core0: r5f@5c00000 { + compatible = "ti,j7200-r5f"; + reg = <0x5c00000 0x00010000>, + <0x5c10000 0x00010000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <245>; + ti,sci-proc-ids = <0x06 0xff>; + resets = <&k3_reset 245 1>; + firmware-name = "j7200-main-r5f0_0-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + + main_r5fss0_core1: r5f@5d00000 { + compatible = "ti,j7200-r5f"; + reg = <0x5d00000 0x00008000>, + <0x5d10000 0x00008000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <246>; + ti,sci-proc-ids = <0x07 0xff>; + resets = <&k3_reset 246 1>; + firmware-name = "j7200-main-r5f0_1-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + }; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi index bb1fe9c12e44..359e3e8a8cd0 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi @@ -2,7 +2,7 @@ /* * Device Tree Source for J7200 SoC Family MCU/WAKEUP Domain peripherals * - * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ &cbass_mcu_wakeup { @@ -289,4 +289,44 @@ compatible = "ti,am3359-adc"; }; }; + + mcu_r5fss0: r5fss@41000000 { + compatible = "ti,j7200-r5fss"; + ti,cluster-mode = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x41000000 0x00 0x41000000 0x20000>, + <0x41400000 0x00 0x41400000 0x20000>; + power-domains = <&k3_pds 249 TI_SCI_PD_EXCLUSIVE>; + + mcu_r5fss0_core0: r5f@41000000 { + compatible = "ti,j7200-r5f"; + reg = <0x41000000 0x00010000>, + <0x41010000 0x00010000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <250>; + ti,sci-proc-ids = <0x01 0xff>; + resets = <&k3_reset 250 1>; + firmware-name = "j7200-mcu-r5f0_0-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + + mcu_r5fss0_core1: r5f@41400000 { + compatible = "ti,j7200-r5f"; + reg = <0x41400000 0x00008000>, + <0x41410000 0x00008000>; + reg-names = "atcm", "btcm"; + ti,sci = <&dmsc>; + ti,sci-dev-id = <251>; + ti,sci-proc-ids = <0x02 0xff>; + resets = <&k3_reset 251 1>; + firmware-name = "j7200-mcu-r5f0_1-fw"; + ti,atcm-enable = <1>; + ti,btcm-enable = <1>; + ti,loczrama = <1>; + }; + }; }; From 7a3b0c2ad3b0cfac5cb8820b8961f0956ff863fb Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Mon, 11 Jan 2021 12:45:53 -0600 Subject: [PATCH 209/584] arm64: dts: ti: k3-j7200-som-p0: Add mailboxes to R5Fs Add the required 'mboxes' property to all the R5F processors for the TI J7200 common processor board. The mailboxes and some shared memory are required for running the Remote Processor Messaging (RPMsg) stack between the host processor and each of the R5Fs. The nodes are therefore added in the common k3-j7200-som-p0.dtsi file so that all of these can be co-located. The chosen sub-mailboxes match the values used in the current firmware images. This can be changed, if needed, as per the system integration needs after making appropriate changes on the firmware side as well. Note that any R5F Core1 resources are needed and used only when that R5F cluster is configured for Split-mode. Signed-off-by: Suman Anna Signed-off-by: Nishanth Menon Reviewed-by: Lokesh Vutla Link: https://lore.kernel.org/r/20210111184554.6748-3-s-anna@ti.com --- arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 18 +++++++++++++++++- 1 file changed, 17 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi index 7b5e9aa0324e..3a82982902c8 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: GPL-2.0 /* - * Copyright (C) 2020 Texas Instruments Incorporated - https://www.ti.com/ + * Copyright (C) 2020-2021 Texas Instruments Incorporated - https://www.ti.com/ */ /dts-v1/; @@ -141,6 +141,22 @@ status = "disabled"; }; +&mcu_r5fss0_core0 { + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>; +}; + +&mcu_r5fss0_core1 { + mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>; +}; + +&main_r5fss0_core0 { + mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>; +}; + +&main_r5fss0_core1 { + mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>; +}; + &main_i2c0 { pinctrl-names = "default"; pinctrl-0 = <&main_i2c0_pins_default>; From c8a9c85d4e702f8c81c08f630f2f30901af5ba16 Mon Sep 17 00:00:00 2001 From: Suman Anna Date: Mon, 11 Jan 2021 12:45:54 -0600 Subject: [PATCH 210/584] arm64: dts: ti: k3-j7200-som-p0: Add DDR carveout memory nodes for R5Fs Two carveout reserved memory nodes each have been added for each of the R5F remote processor devices within both the MCU and MAIN domains on the TI J7200 EVM boards. These nodes are assigned to the respective rproc device nodes as well. The first region will be used as the DMA pool for the rproc device, and the second region will furnish the static carveout regions for the firmware memory. An additional reserved memory node is also added to reserve a portion of the DDR memory to be used for performing inter-processor communication between all the remote processors running RTOS. 8 MB of memory is reserved for this purpose, and this accounts for all the vrings and vring buffers between all the possible pairs of remote processors. The current carveout addresses and sizes are defined statically for each device. The R5F processors do not have an MMU, and as such require the exact memory used by the firmwares to be set-aside. The firmware images do not require any RSC_CARVEOUT entries in their resource tables either to allocate the memory for firmware memory segments. NOTE: 1. The R5F1 carveouts are needed only if the R5F cluster is running in Split (non-LockStep) mode. The reserved memory nodes can be disabled later on if there is no use-case defined to use the corresponding remote processor. 2. The J7200 SoCs have no DSPs and one less R5F cluster compared to J721E SoCs. So, while the carveout memories reserved for the R5F clusters present on the SoC match to those on J721E, the overall memory map reserved for firmwares is quite different. Signed-off-by: Suman Anna Signed-off-by: Nishanth Menon Reviewed-by: Lokesh Vutla Link: https://lore.kernel.org/r/20210111184554.6748-4-s-anna@ti.com --- arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi | 62 +++++++++++++++++++++ 1 file changed, 62 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi index 3a82982902c8..a988e2ab2ba1 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi @@ -25,6 +25,60 @@ alignment = <0x1000>; no-map; }; + + mcu_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0000000 0x00 0x100000>; + no-map; + }; + + mcu_r5fss0_core0_memory_region: r5f-memory@a0100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa0100000 0x00 0xf00000>; + no-map; + }; + + mcu_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1000000 0x00 0x100000>; + no-map; + }; + + mcu_r5fss0_core1_memory_region: r5f-memory@a1100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa1100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a2000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core0_memory_region: r5f-memory@a2100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa2100000 0x00 0xf00000>; + no-map; + }; + + main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a3000000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3000000 0x00 0x100000>; + no-map; + }; + + main_r5fss0_core1_memory_region: r5f-memory@a3100000 { + compatible = "shared-dma-pool"; + reg = <0x00 0xa3100000 0x00 0xf00000>; + no-map; + }; + + rtos_ipc_memory_region: ipc-memories@a4000000 { + reg = <0x00 0xa4000000 0x00 0x00800000>; + alignment = <0x1000>; + no-map; + }; }; }; @@ -143,18 +197,26 @@ &mcu_r5fss0_core0 { mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core0>; + memory-region = <&mcu_r5fss0_core0_dma_memory_region>, + <&mcu_r5fss0_core0_memory_region>; }; &mcu_r5fss0_core1 { mboxes = <&mailbox0_cluster0 &mbox_mcu_r5fss0_core1>; + memory-region = <&mcu_r5fss0_core1_dma_memory_region>, + <&mcu_r5fss0_core1_memory_region>; }; &main_r5fss0_core0 { mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core0>; + memory-region = <&main_r5fss0_core0_dma_memory_region>, + <&main_r5fss0_core0_memory_region>; }; &main_r5fss0_core1 { mboxes = <&mailbox0_cluster1 &mbox_main_r5fss0_core1>; + memory-region = <&main_r5fss0_core1_dma_memory_region>, + <&main_r5fss0_core1_memory_region>; }; &main_i2c0 { From 7cd8567d988a6aad64e56e9afda358c68716d75e Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Tue, 1 Dec 2020 12:14:40 +0100 Subject: [PATCH 211/584] ARM: dts: stm32: Enable internal pull-ups for SDMMC1 on DHCOM SoM The default state of SD bus and clock line is logical HI. SD card IO is open-drain and pulls the bus lines LO. Always enable the SD bus pull ups to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus voltage level shifter, the pull ups are built into the level shifter, however that has no negative impact. Signed-off-by: Marek Vasut Cc: Alexandre Torgue Cc: Maxime Coquelin Cc: Patrice Chotard Cc: Patrick Delaunay Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi index daff5318f301..97c6e0cd582c 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi @@ -400,6 +400,20 @@ status = "okay"; }; +&sdmmc1_b4_pins_a { + /* + * SD bus pull-up resistors: + * - optional on SoMs with SD voltage translator + * - mandatory on SoMs without SD voltage translator + */ + pins1 { + bias-pull-up; + }; + pins2 { + bias-pull-up; + }; +}; + &sdmmc2 { pinctrl-names = "default", "opendrain", "sleep"; pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>; From 32d4878b26c1c69c893c6a1f6f7004d1bcc57a79 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 14 Jan 2021 15:52:10 +0100 Subject: [PATCH 212/584] ARM: dts: stm32: Disable SDMMC1 CKIN feedback clock on DHCOM The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter or without one on the SDMMC1 interface. Because the SDMMC1 interface is limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback clock to permit operation of the same U-Boot image on both SoM with and without voltage level shifter. Signed-off-by: Marek Vasut Cc: Alexandre Torgue Cc: Maxime Coquelin Cc: Patrice Chotard Cc: Patrick Delaunay Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi index 97c6e0cd582c..2a20818c91e4 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi @@ -394,7 +394,6 @@ disable-wp; st,sig-dir; st,neg-edge; - st,use-ckin; bus-width = <4>; vmmc-supply = <&vdd_sd>; status = "okay"; From 2f9c3506b5c553a24d738c5c958cad84d5cf4280 Mon Sep 17 00:00:00 2001 From: Alexander Dahl Date: Mon, 28 Dec 2020 17:32:16 +0100 Subject: [PATCH 213/584] ARM: dts: stm32: Fix schema warnings for pwm-leds on lxa-mc1 The node names for devices using the pwm-leds driver follow a certain naming scheme (now). Parent node name is not enforced, but recommended by DT project. DTC arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml CHECK arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml /home/alex/build/linux/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dt.yaml: led-rgb: 'led-blue', 'led-green', 'led-red' do not match any of the regexes: '^led(-[0-9a-f]+)?$', 'pinctrl-[0-9]+' From schema: /home/alex/src/linux/leds/Documentation/devicetree/bindings/leds/leds-pwm.yaml Signed-off-by: Alexander Dahl Acked-by: Ahmad Fatoum Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts index cda8e871f999..1e9bf7eea0f1 100644 --- a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts +++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts @@ -36,34 +36,35 @@ stdout-path = &uart4; }; - led-act { + led-controller-0 { compatible = "gpio-leds"; - led-green { + led-0 { label = "mc1:green:act"; gpios = <&gpioa 13 GPIO_ACTIVE_LOW>; linux,default-trigger = "heartbeat"; }; }; - led-rgb { + led-controller-1 { compatible = "pwm-leds"; - led-red { + /* led-1 to led-3 are part of a single RGB led */ + led-1 { label = "mc1:red:rgb"; pwms = <&leds_pwm 1 1000000 0>; max-brightness = <255>; active-low; }; - led-green { + led-2 { label = "mc1:green:rgb"; pwms = <&leds_pwm 2 1000000 0>; max-brightness = <255>; active-low; }; - led-blue { + led-3 { label = "mc1:blue:rgb"; pwms = <&leds_pwm 3 1000000 0>; max-brightness = <255>; From 8ba396551d5d3e862c195e7373e51c4056429c91 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 24 Dec 2020 07:27:26 +0100 Subject: [PATCH 214/584] ARM: dts: stm32: Disable KS8851 and FMC on PicoITX board The PicoITX has only one ethernet routed out, so the KS8851 is not used at all. Disable the KS8851 and the entire FMC controller. Signed-off-by: Marek Vasut Cc: Alexandre Torgue Cc: Maxime Coquelin Cc: Patrice Chotard Cc: Patrick Delaunay Cc: linux-stm32@st-md-mailman.stormreply.com To: linux-arm-kernel@lists.infradead.org Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi index 32700cca24c8..757707766fa0 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi @@ -36,6 +36,10 @@ status = "disabled"; }; +&fmc { + status = "disabled"; +}; + &gpioa { /* * NOTE: The USB Port on the PicoITX needs a PWR_EN signal to enable @@ -94,6 +98,10 @@ /delete-property/dma-names; }; +&ksz8851 { + status = "disabled"; +}; + &usart3 { pinctrl-names = "default"; pinctrl-0 = <&usart3_pins_a>; From 8f03014019f4afab7209f31edd584fcaed62c455 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Fri, 15 Jan 2021 05:41:56 +0300 Subject: [PATCH 215/584] arm64: dts: qcom: qrb5165-rb5: enable cdsp device Enable Compute DSP (cdsp) on QRB5165-RB5 platform and provide firmware filename used to boot the cdsp. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210115024156.92265-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 477ff91dc460..2d713e0c7d6a 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -444,6 +444,11 @@ }; }; +&cdsp { + status = "okay"; + firmware-name = "qcom/sm8250/cdsp.mbn"; +}; + &dsi0 { status = "okay"; vdda-supply = <&vreg_l9a_1p2>; From c2c76ddb140291724482028327bd648944571ff5 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Fri, 15 Jan 2021 05:47:13 +0300 Subject: [PATCH 216/584] arm64: dts: qcom: qrb5165-rb5: add HDMI audio playback Add support for audio output over the HDMI output using Tertiary I2S and LT9611UXC DSI-to-HDMI bridge. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210115024713.92574-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 2d713e0c7d6a..7c2a798c6ac6 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -697,6 +697,7 @@ "VA DMIC0", "vdd-micb", "VA DMIC1", "vdd-micb", "MM_DL1", "MultiMedia1 Playback", + "MM_DL2", "MultiMedia2 Playback", "MultiMedia3 Capture", "MM_UL3"; mm1-dai-link { @@ -706,6 +707,13 @@ }; }; + mm2-dai-link { + link-name = "MultiMedia2"; + cpu { + sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>; + }; + }; + mm3-dai-link { link-name = "MultiMedia3"; cpu { @@ -713,6 +721,21 @@ }; }; + hdmi-dai-link { + link-name = "HDMI Playback"; + cpu { + sound-dai = <&q6afedai TERTIARY_MI2S_RX>; + }; + + platform { + sound-dai = <&q6routing>; + }; + + codec { + sound-dai = <<9611_codec 0>; + }; + }; + dma-dai-link { link-name = "WSA Playback"; cpu { From 74097d805edb9305a2a588a8ece82d2495ff5a88 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 9 Jan 2021 04:12:52 +0300 Subject: [PATCH 217/584] arm64: dts: qcom: sm8250: correct sdhc_2 xo clk sdhc_2 uses 19200000 Hz clock rather than wrongly specified xo_board (39400000 Hz). Specify correct clock to fix DLL setup for SDR104 mode. Signed-off-by: Dmitry Baryshkov Fixes: c4cf0300be84 ("arm64: dts: qcom: sm8250: Add support for SDC2") Link: https://lore.kernel.org/r/20210109011252.3436533-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 6b4cf4426859..1c3ab5a3783d 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1825,7 +1825,7 @@ clocks = <&gcc GCC_SDCC2_AHB_CLK>, <&gcc GCC_SDCC2_APPS_CLK>, - <&xo_board>; + <&rpmhcc RPMH_CXO_CLK>; clock-names = "iface", "core", "xo"; iommus = <&apps_smmu 0x4a0 0x0>; qcom,dll-config = <0x0007642c>; From 599bbb639e83029d7237b4114aaf237619c525eb Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Tue, 29 Dec 2020 13:03:20 +0100 Subject: [PATCH 218/584] dt-bindings: arm: fsl: add Kontron sl28 variant 1 Add the a new variant for the Kontron SMARC-sAL28 board. Signed-off-by: Michael Walle Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 2ae66407e2aa..89ef175ee49f 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -848,10 +848,12 @@ properties: Kontron SMARC-sAL28 board on the SMARC Eval Carrier 2.0 items: - enum: + - kontron,sl28-var1-ads2 - kontron,sl28-var2-ads2 - kontron,sl28-var3-ads2 - kontron,sl28-var4-ads2 - enum: + - kontron,sl28-var1 - kontron,sl28-var2 - kontron,sl28-var3 - kontron,sl28-var4 @@ -862,6 +864,7 @@ properties: Kontron SMARC-sAL28 board (on a generic/undefined carrier) items: - enum: + - kontron,sl28-var1 - kontron,sl28-var2 - kontron,sl28-var3 - kontron,sl28-var4 From 642856097c186c0d675a8ac59efca557e8d9c0eb Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 11 Jan 2021 09:21:34 +0100 Subject: [PATCH 219/584] arm64: dts: freescale: sl28: add variant 1 There is a new variant 1 of this board available. It features up to four SerDes lanes for customer use. Add a new device tree which features just the basic peripherals. A customer will then have to modify or append to this device tree. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../fsl-ls1028a-kontron-sl28-var1.dts | 62 +++++++++++++++++++ 2 files changed, 63 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 38559943c15d..17fc731da700 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -6,6 +6,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-qds.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-rdb.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-kbox-a-230-ls.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28.dtb +dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var1.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var2.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var3-ads2.dtb dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-kontron-sl28-var4.dtb diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts new file mode 100644 index 000000000000..6c309b97587d --- /dev/null +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var1.dts @@ -0,0 +1,62 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Device Tree file for the Kontron SMARC-sAL28 board. + * + * This is for the network variant 1 which has one ethernet port. It is + * different than the base variant, which also has one port, but here the + * port is connected via RGMII. This port is not TSN aware. + * None of the four SerDes lanes are used by the module, instead they are + * all led out to the carrier for customer use. + * + * Copyright (C) 2020 Michael Walle + * + */ + +/dts-v1/; +#include "fsl-ls1028a-kontron-sl28.dts" +#include + +/ { + model = "Kontron SMARC-sAL28 (4 Lanes)"; + compatible = "kontron,sl28-var1", "kontron,sl28", "fsl,ls1028a"; +}; + +&enetc_port0 { + status = "disabled"; + /* + * Delete both the phy-handle to the old phy0 label as well as + * the mdio node with the old phy node with the old phy0 label. + */ + /delete-property/ phy-handle; + /delete-node/ mdio; +}; + +&enetc_port1 { + phy-handle = <&phy0>; + phy-connection-type = "rgmii-id"; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy0: ethernet-phy@4 { + reg = <0x4>; + eee-broken-1000t; + eee-broken-100tx; + qca,clk-out-frequency = <125000000>; + qca,clk-out-strength = ; + vddio-supply = <&vddh>; + + vddio: vddio-regulator { + regulator-name = "VDDIO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vddh: vddh-regulator { + regulator-name = "VDDH"; + }; + }; + }; +}; From f18e6d573b80364bc6be71cd32d5eb92543a99c1 Mon Sep 17 00:00:00 2001 From: Leonard Crestez Date: Thu, 7 Jan 2021 13:17:50 +0100 Subject: [PATCH 220/584] arm64: dts: imx8mq: Add NOC node Add initial support for dynamic frequency scaling of the main NOC on imx8mq. Make DDRC the parent of the NOC (using passive governor) so that the main NOC is automatically scaled together with DDRC by default. Support for proactive scaling via interconnect will come on top. Signed-off-by: Leonard Crestez Signed-off-by: Martin Kepplinger Acked-by: Georgi Djakov Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 24 +++++++++++++++++++++++ 1 file changed, 24 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 9fcb001b8dde..efabd7bb88cf 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -1169,6 +1169,30 @@ }; }; + noc: interconnect@32700000 { + compatible = "fsl,imx8mq-noc", "fsl,imx8m-noc"; + reg = <0x32700000 0x100000>; + clocks = <&clk IMX8MQ_CLK_NOC>; + fsl,ddrc = <&ddrc>; + operating-points-v2 = <&noc_opp_table>; + + noc_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-133M { + opp-hz = /bits/ 64 <133333333>; + }; + + opp-400M { + opp-hz = /bits/ 64 <400000000>; + }; + + opp-800M { + opp-hz = /bits/ 64 <800000000>; + }; + }; + }; + bus@32c00000 { /* AIPS4 */ compatible = "fsl,aips-bus", "simple-bus"; reg = <0x32c00000 0x400000>; From 20cf8d981c8164367cbccfabbd306b7c9f7ad1ed Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Mon, 11 Jan 2021 09:21:44 +0100 Subject: [PATCH 221/584] arm64: dts: imx8mq: Add interconnect provider property Add #interconnect-cells on main &noc so that it will probe the interconnect provider. Signed-off-by: Martin Kepplinger Acked-by: Georgi Djakov Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index efabd7bb88cf..02b22faa8147 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -1174,6 +1174,7 @@ reg = <0x32700000 0x100000>; clocks = <&clk IMX8MQ_CLK_NOC>; fsl,ddrc = <&ddrc>; + #interconnect-cells = <1>; operating-points-v2 = <&noc_opp_table>; noc_opp_table: opp-table { From ad1abc8a03fdbc05b3390962b15287d4e7c5db22 Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Thu, 7 Jan 2021 13:17:53 +0100 Subject: [PATCH 222/584] arm64: dts: imx8mq: Add interconnect for lcdif Add interconnect ports for lcdif to set bus capabilities. Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 02b22faa8147..c9874dfe0cd4 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -11,6 +11,7 @@ #include "dt-bindings/input/input.h" #include #include +#include #include "imx8mq-pinfunc.h" / { @@ -524,6 +525,8 @@ <&clk IMX8MQ_VIDEO_PLL1>, <&clk IMX8MQ_VIDEO_PLL1_OUT>; assigned-clock-rates = <0>, <0>, <0>, <594000000>; + interconnects = <&noc IMX8MQ_ICM_LCDIF &noc IMX8MQ_ICS_DRAM>; + interconnect-names = "dram"; status = "disabled"; port@0 { From 288ef8a42612df516e2e598a9ca5b3d9be846290 Mon Sep 17 00:00:00 2001 From: Caleb Connolly Date: Thu, 14 Jan 2021 20:31:57 +0000 Subject: [PATCH 223/584] arm64: dts: sdm845: add oneplus6/6t devices Add initial support for the OnePlus 6 (enchilada) and 6T (fajita) based on the sdm845-mtp DT with the following functionality: * Touch * Display * GPU * Wlan and Bluetooth * USB peripheral mode * Remoteproc Reviewed-by: Konrad Dybcio Signed-off-by: Caleb Connolly Link: https://lore.kernel.org/r/20210114203057.64541-2-caleb@connolly.tech Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 2 + .../boot/dts/qcom/sdm845-oneplus-common.dtsi | 623 ++++++++++++++++++ .../dts/qcom/sdm845-oneplus-enchilada.dts | 19 + .../boot/dts/qcom/sdm845-oneplus-fajita.dts | 23 + 4 files changed, 667 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts create mode 100644 arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 6a4be237f344..b5d86739f781 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -44,6 +44,8 @@ dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r2.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-cheza-r3.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-db845c.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-enchilada.dtb +dtb-$(CONFIG_ARCH_QCOM) += sdm845-oneplus-fajita.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm845-xiaomi-beryllium.dtb dtb-$(CONFIG_ARCH_QCOM) += sdm850-lenovo-yoga-c630.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi new file mode 100644 index 000000000000..8f617f7b6d34 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi @@ -0,0 +1,623 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +/dts-v1/; + +#include +#include +#include + +#include "sdm845.dtsi" +#include "pm8998.dtsi" +#include "pmi8998.dtsi" + +/delete-node/ &rmtfs_mem; + +/ { + aliases { + hsuart0 = &uart6; + }; + + gpio-keys { + compatible = "gpio-keys"; + label = "Volume keys"; + autorepeat; + + pinctrl-names = "default"; + pinctrl-0 = <&volume_down_gpio &volume_up_gpio>; + + vol-down { + label = "Volume down"; + linux,code = ; + gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + + vol-up { + label = "Volume up"; + linux,code = ; + gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <15>; + }; + }; + + reserved-memory { + /* + * The rmtfs memory region in downstream is 'dynamically allocated' + * but given the same address every time. Hard code it as this address is + * where the modem firmware expects it to be. + */ + rmtfs_mem: memory@f5b01000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xf5b01000 0 0x200000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <15>; + }; + + /* + * It seems like reserving the old rmtfs_mem region is also needed to prevent + * random crashes which are most likely modem related, more testing needed. + */ + removed_region: memory@88f00000 { + no-map; + reg = <0 0x88f00000 0 0x200000>; + }; + + ramoops: ramoops@ac300000 { + compatible = "ramoops"; + reg = <0 0xac300000 0 0x400000>; + record-size = <0x40000>; + console-size = <0x40000>; + ftrace-size = <0x40000>; + pmsg-size = <0x200000>; + devinfo-size = <0x1000>; + ecc-size = <16>; + }; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + }; + + /* + * Apparently RPMh does not provide support for PM8998 S4 because it + * is always-on; model it as a fixed regulator. + */ + vreg_s4a_1p8: pm8998-smps4 { + compatible = "regulator-fixed"; + regulator-name = "vreg_s4a_1p8"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + + vin-supply = <&vph_pwr>; + }; + + /* + * The touchscreen regulator seems to be controlled somehow by a gpio. + * Model it as a fixed regulator and keep it on. Without schematics we + * don't know how this is actually wired up... + */ + ts_1p8_supply: ts-1p8-regulator { + compatible = "regulator-fixed"; + regulator-name = "ts_1p8_supply"; + + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + gpio = <&tlmm 88 0>; + enable-active-high; + regulator-boot-on; + }; +}; + +&adsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/adsp.mbn"; +}; + +&apps_rsc { + pm8998-rpmh-regulators { + compatible = "qcom,pm8998-rpmh-regulators"; + qcom,pmic-id = "a"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + vdd-s13-supply = <&vph_pwr>; + vdd-l1-l27-supply = <&vreg_s7a_1p025>; + vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>; + vdd-l3-l11-supply = <&vreg_s7a_1p025>; + vdd-l4-l5-supply = <&vreg_s7a_1p025>; + vdd-l6-supply = <&vph_pwr>; + vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>; + vdd-l9-supply = <&vreg_bob>; + vdd-l10-l23-l25-supply = <&vreg_bob>; + vdd-l13-l19-l21-supply = <&vreg_bob>; + vdd-l16-l28-supply = <&vreg_bob>; + vdd-l18-l22-supply = <&vreg_bob>; + vdd-l20-l24-supply = <&vreg_bob>; + vdd-l26-supply = <&vreg_s3a_1p35>; + vin-lvs-1-2-supply = <&vreg_s4a_1p8>; + + vreg_s3a_1p35: smps3 { + regulator-min-microvolt = <1352000>; + regulator-max-microvolt = <1352000>; + }; + + vreg_s5a_2p04: smps5 { + regulator-min-microvolt = <1904000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7a_1p025: smps7 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1028000>; + }; + + vdda_mipi_dsi0_pll: + vdda_qlink_lv: + vdda_ufs1_core: + vdda_usb1_ss_core: + vreg_l1a_0p875: ldo1 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <880000>; + regulator-initial-mode = ; + }; + + vreg_l2a_1p2: ldo2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + regulator-always-on; + }; + + vreg_l5a_0p8: ldo5 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = ; + }; + + vreg_l7a_1p8: ldo7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + vdda_qusb_hs0_1p8: + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + vreg_l14a_1p88: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + regulator-always-on; + }; + + vreg_l17a_1p3: ldo17 { + regulator-min-microvolt = <1304000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = ; + }; + + vreg_l20a_2p95: ldo20 { + regulator-min-microvolt = <2704000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = ; + }; + + vdda_qusb_hs0_3p1: + vreg_l24a_3p075: ldo24 { + regulator-min-microvolt = <3088000>; + regulator-max-microvolt = <3088000>; + regulator-initial-mode = ; + }; + + vreg_l25a_3p3: ldo25 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = ; + }; + + vdda_mipi_dsi0_1p2: + vdda_ufs1_1p2: + vreg_l26a_1p2: ldo26 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + + vreg_l28a_3p0: ldo28 { + regulator-min-microvolt = <2856000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = ; + }; + }; + + pmi8998-rpmh-regulators { + compatible = "qcom,pmi8998-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-bob-supply = <&vph_pwr>; + + vreg_bob: bob { + regulator-min-microvolt = <3312000>; + regulator-max-microvolt = <3600000>; + regulator-initial-mode = ; + regulator-allow-bypass; + }; + }; + + pm8005-rpmh-regulators { + compatible = "qcom,pm8005-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + + vreg_s3c_0p6: smps3 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <600000>; + }; + }; +}; + +&cdsp_pas { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn"; +}; + +&dsi0 { + status = "okay"; + vdda-supply = <&vdda_mipi_dsi0_1p2>; + + #address-cells = <1>; + #size-cells = <0>; + + /* + * Both devices use different panels but all other properties + * are common. Compatible line is declared in device dts. + */ + display_panel: panel@0 { + status = "disabled"; + + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vddio-supply = <&vreg_l14a_1p88>; + + reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; +}; + +&dsi0_out { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi0_phy { + status = "okay"; + vdds-supply = <&vdda_mipi_dsi0_pll>; +}; + +&gcc { + protected-clocks = , + , + , + , + ; +}; + +&gpu { + zap-shader { + memory-region = <&gpu_mem>; + firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn"; + }; +}; + +&i2c12 { + status = "okay"; + clock-frequency = <400000>; + + synaptics-rmi4-i2c@20 { + compatible = "syna,rmi4-i2c"; + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_default_pins>; + + vdd-supply = <&vreg_l28a_3p0>; + vio-supply = <&ts_1p8_supply>; + + syna,reset-delay-ms = <200>; + syna,startup-delay-ms = <200>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4_f12: rmi4-f12@12 { + reg = <0x12>; + touchscreen-x-mm = <68>; + touchscreen-y-mm = <144>; + syna,sensor-type = <1>; + syna,rezero-wait-ms = <200>; + }; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_mdp { + status = "okay"; +}; + +/* Modem/wifi*/ +&mss_pil { + status = "okay"; + firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn"; +}; + +&pm8998_gpio { + volume_down_gpio: pm8998_gpio5 { + pinconf { + pins = "gpio5"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; + + volume_up_gpio: pm8998_gpio6 { + pinconf { + pins = "gpio6"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,drive-strength = <0>; + }; + }; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qup_i2c12_default { + mux { + pins = "gpio49", "gpio50"; + function = "qup12"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_i2c10_default { + pinconf { + pins = "gpio55", "gpio56"; + drive-strength = <2>; + bias-disable; + }; +}; + +&qup_uart9_default { + pinconf-tx { + pins = "gpio4"; + drive-strength = <2>; + bias-disable; + }; + + pinconf-rx { + pins = "gpio5"; + drive-strength = <2>; + bias-pull-up; + }; +}; + +/* + * Prevent garbage data on bluetooth UART lines + */ +&qup_uart6_default { + pinmux { + pins = "gpio45", "gpio46", "gpio47", "gpio48"; + function = "qup6"; + }; + + cts { + pins = "gpio45"; + bias-pull-down; + }; + + rts-tx { + pins = "gpio46", "gpio47"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio48"; + bias-pull-up; + }; +}; + +&uart6 { + status = "okay"; + + bluetooth { + compatible = "qcom,wcn3990-bt"; + + /* + * This path is relative to the qca/ + * subdir under lib/firmware. + */ + firmware-name = "oneplus6/crnv21.bin"; + + vddio-supply = <&vreg_s4a_1p8>; + vddxo-supply = <&vreg_l7a_1p8>; + vddrf-supply = <&vreg_l17a_1p3>; + vddch0-supply = <&vreg_l25a_3p3>; + max-speed = <3200000>; + }; +}; + +&ufs_mem_hc { + status = "okay"; + + reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l20a_2p95>; + vcc-max-microamp = <600000>; +}; + +&ufs_mem_phy { + status = "okay"; + + vdda-phy-supply = <&vdda_ufs1_core>; + vdda-pll-supply = <&vdda_ufs1_1p2>; +}; + +&usb_1 { + status = "okay"; + + /* + * disable USB3 clock requirement as the device only supports + * USB2. + */ + qcom,select-utmi-as-pipe-clk; +}; + +&usb_1_dwc3 { + /* + * We don't have the capability to switch modes yet. + */ + dr_mode = "peripheral"; + + /* fastest mode for USB 2 */ + maximum-speed = "high-speed"; + + /* Remove USB3 phy as it's unused on this device. */ + phys = <&usb_1_hsphy>; + phy-names = "usb2-phy"; +}; + +&usb_1_hsphy { + status = "okay"; + + vdd-supply = <&vdda_usb1_ss_core>; + vdda-pll-supply = <&vdda_qusb_hs0_1p8>; + vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>; + + qcom,imp-res-offset-value = <8>; + qcom,hstx-trim-value = ; + qcom,preemphasis-level = ; + qcom,preemphasis-width = ; +}; + +&tlmm { + gpio-reserved-ranges = <0 4>, <81 4>; + + tri_state_key_default: tri_state_key_default { + mux { + pins = "gpio40", "gpio42", "gpio26"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + }; + + ts_default_pins: ts-int { + mux { + pins = "gpio99", "gpio125"; + function = "gpio"; + drive-strength = <16>; + bias-pull-up; + }; + }; + + panel_reset_pins: panel-reset { + mux { + pins = "gpio6", "gpio25", "gpio26"; + function = "gpio"; + drive-strength = <8>; + bias-disable = <0>; + }; + }; + + panel_te_pin: panel-te { + mux { + pins = "gpio10"; + function = "mdp_vsync"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + }; + + panel_esd_pin: panel-esd { + mux { + pins = "gpio30"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + input-enable; + }; + }; +}; + +&wifi { + status = "okay"; + vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + + qcom,snoc-host-cap-8bit-quirk; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts new file mode 100644 index 000000000000..72842c887617 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6 (enchilada) device tree. + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6"; + compatible = "oneplus,enchilada", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,sofef00"; +}; diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts new file mode 100644 index 000000000000..969b36dc9e2c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM845 OnePlus 6T (fajita) device tree. + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845-oneplus-common.dtsi" + +/ { + model = "OnePlus 6T"; + compatible = "oneplus,fajita", "qcom,sdm845"; +}; + +&display_panel { + status = "okay"; + + compatible = "samsung,s6e3fc2x01"; +}; + +&rmi4_f12 { + touchscreen-y-mm = <148>; +}; From 6be4ba5467bed412f1e68a8aa1e22279bfb8fcd5 Mon Sep 17 00:00:00 2001 From: Steev Klimaszewski Date: Tue, 12 Jan 2021 17:06:40 +0800 Subject: [PATCH 224/584] arm64: dts: sdm850: Add OPP tables for 2.84 and 2.96GHz Running cpufreq-hw driver on Lenovo Yoga C630 laptop, the following warning messages will be seen. [ 3.415340] cpu cpu4: Voltage update failed freq=2841600 [ 3.418755] cpu cpu4: failed to update OPP for freq=2841600 [ 3.422949] cpu cpu4: Voltage update failed freq=2956800 [ 3.427086] cpu cpu4: failed to update OPP for freq=2956800 This is because the cpufreq-hw lookup table of SDM850 provides these two set-points, but they are missing from OPP table in DT. Let's create sdm850.dtsi to add the OPP for them, so that the warning will be gone. Signed-off-by: Steev Klimaszewski Signed-off-by: Shawn Guo Link: https://lore.kernel.org/r/20210112090640.20062-1-shawn.guo@linaro.org Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom/sdm850-lenovo-yoga-c630.dts | 2 +- arch/arm64/boot/dts/qcom/sdm850.dtsi | 21 +++++++++++++++++++ 2 files changed, 22 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/qcom/sdm850.dtsi diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts index 13fdd02cffe6..94705d02f46c 100644 --- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts +++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts @@ -13,7 +13,7 @@ #include #include #include -#include "sdm845.dtsi" +#include "sdm850.dtsi" #include "pm8998.dtsi" / { diff --git a/arch/arm64/boot/dts/qcom/sdm850.dtsi b/arch/arm64/boot/dts/qcom/sdm850.dtsi new file mode 100644 index 000000000000..b1c2cf566c7a --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sdm850.dtsi @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SDM850 SoC device tree source + * + * Copyright (c) 2020, The Linux Foundation. All rights reserved. + */ + +#include "sdm845.dtsi" + +&cpu4_opp_table { + cpu4_opp33: opp-2841600000 { + opp-hz = /bits/ 64 <2841600000>; + opp-peak-kBps = <7216000 25497600>; + }; + + cpu4_opp34: opp-2956800000 { + opp-hz = /bits/ 64 <2956800000>; + opp-peak-kBps = <7216000 25497600>; + turbo-mode; + }; +}; From 3716a583fe0bbe3babf4ce260064a7fa13d6d989 Mon Sep 17 00:00:00 2001 From: Stephan Gerhold Date: Mon, 11 Jan 2021 18:53:58 +0100 Subject: [PATCH 225/584] arm64: dts: qcom: msm8916-samsung-a2015: Fix sensors When the BMC150 accelerometer/magnetometer was added to the device tree, the sensors were working without specifying any regulator supplies, likely because the regulators were on by default and then never turned off. For some reason, this is no longer the case for pm8916_l17, which prevents the sensors from working in some cases. Now that the bmc150_accel/bmc150_magn drivers can enable necessary regulators, declare the necessary regulator supplies to make the sensors work again. Fixes: 079f81acf10f ("arm64: dts: qcom: msm8916-samsung-a2015: Add accelerometer/magnetometer") Signed-off-by: Stephan Gerhold Link: https://lore.kernel.org/r/20210111175358.97171-1-stephan@gerhold.net Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi index f91269492d72..f1af798abd74 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi @@ -106,6 +106,9 @@ interrupt-parent = <&msmgpio>; interrupts = <115 IRQ_TYPE_EDGE_RISING>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; + pinctrl-names = "default"; pinctrl-0 = <&accel_int_default>; }; @@ -113,6 +116,9 @@ magnetometer@12 { compatible = "bosch,bmc150_magn"; reg = <0x12>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l5>; }; }; From b4791e695526939be3c4f043fe69222d2ba7c171 Mon Sep 17 00:00:00 2001 From: Danny Lin Date: Mon, 11 Jan 2021 17:32:53 -0800 Subject: [PATCH 226/584] arm64: dts: qcom: sm8250: Define CPU topology sm8250 has a big.LITTLE CPU setup with DynamIQ, so all cores are within the same CPU cluster and LLC (Last-Level Cache) domain. Define this topology to help the scheduler make decisions. Signed-off-by: Danny Lin Link: https://lore.kernel.org/r/20210112013255.415253-1-danny@kdrag0n.dev Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 36 ++++++++++++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 1c3ab5a3783d..8d5c5d44187a 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -203,6 +203,42 @@ next-level-cache = <&L3_0>; }; }; + + cpu-map { + cluster0 { + core0 { + cpu = <&CPU0>; + }; + + core1 { + cpu = <&CPU1>; + }; + + core2 { + cpu = <&CPU2>; + }; + + core3 { + cpu = <&CPU3>; + }; + + core4 { + cpu = <&CPU4>; + }; + + core5 { + cpu = <&CPU5>; + }; + + core6 { + cpu = <&CPU6>; + }; + + core7 { + cpu = <&CPU7>; + }; + }; + }; }; firmware { From 6aabed5526ee2cbe377b9b19cbb2cbb832bdfb22 Mon Sep 17 00:00:00 2001 From: Danny Lin Date: Mon, 11 Jan 2021 17:32:54 -0800 Subject: [PATCH 227/584] arm64: dts: qcom: sm8250: Add CPU capacities and energy model MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Power and performance measurements were made using my freqbench [1] benchmark coordinator, which isolates, offlines, and disables the timer tick on test CPUs to maximize accuracy. It uses EEMBC CoreMark [2] as the workload and measures power usage using the PM8150B PMIC's fuel gauge. The energy model dynamic-power-coefficient values were calculated with DPC = µW / MHz / V^2 for each OPP, and averaged across all OPPs within each cluster for the final coefficient. Voltages were obtained from the qcom-cpufreq-hw driver that reads voltages from the OSM LUT programmed into the SoC. Normalized DMIPS/MHz capacity scale values for each CPU were calculated from CoreMarks/MHz (CoreMark iterations per second per MHz), which serves the same purpose. For each CPU, the final capacity-dmips-mhz value is the C/MHz value of its maximum frequency normalized to SCHED_CAPACITY_SCALE (1024) for the fastest CPU in the system. A Xiaomi Redmi K30S Ultra device running a downstream Qualcomm 4.19 kernel was used for benchmarking to ensure proper frequency scaling and other low-level controls. Raw benchmark results can be found in the freqbench repository [3]. Below is a human-readable summary: Frequency domains: cpu1 cpu4 cpu7 Offline CPUs: cpu1 cpu2 cpu3 cpu4 cpu5 cpu6 cpu7 Baseline power usage: 1223 mW ===== CPU 1 ===== Frequencies: 300 403 518 614 691 787 883 979 1075 1171 1248 1344 1420 1516 1612 1708 1804 300: 1114 3.7 C/MHz 29 mW 6.4 J 39.0 I/mJ 224.5 s 403: 1497 3.7 C/MHz 33 mW 5.5 J 45.2 I/mJ 167.0 s 518: 1925 3.7 C/MHz 48 mW 6.3 J 39.7 I/mJ 129.9 s 614: 2281 3.7 C/MHz 73 mW 8.0 J 31.1 I/mJ 109.6 s 691: 2566 3.7 C/MHz 46 mW 4.5 J 55.2 I/mJ 97.4 s 787: 2923 3.7 C/MHz 86 mW 7.4 J 33.8 I/mJ 85.5 s 883: 3279 3.7 C/MHz 77 mW 5.9 J 42.5 I/mJ 76.2 s 979: 3635 3.7 C/MHz 65 mW 4.4 J 56.2 I/mJ 68.8 s 1075: 3992 3.7 C/MHz 71 mW 4.4 J 56.2 I/mJ 62.6 s 1171: 4348 3.7 C/MHz 121 mW 6.9 J 36.0 I/mJ 57.5 s 1248: 4633 3.7 C/MHz 79 mW 4.2 J 58.9 I/mJ 54.0 s 1344: 4990 3.7 C/MHz 81 mW 4.0 J 61.7 I/mJ 50.1 s 1420: 5275 3.7 C/MHz 85 mW 4.0 J 61.8 I/mJ 47.4 s 1516: 5632 3.7 C/MHz 88 mW 3.9 J 64.3 I/mJ 44.4 s 1612: 5988 3.7 C/MHz 92 mW 3.8 J 65.4 I/mJ 41.7 s 1708: 6346 3.7 C/MHz 96 mW 3.8 J 66.3 I/mJ 39.4 s 1804: 6701 3.7 C/MHz 105 mW 3.9 J 63.5 I/mJ 37.3 s ===== CPU 4 ===== Frequencies: 710 825 940 1056 1171 1286 1382 1478 1574 1670 1766 1862 1958 2054 2150 2246 2342 2419 710: 6022 8.5 C/MHz 123 mW 5.1 J 49.1 I/mJ 41.5 s 825: 7001 8.5 C/MHz 142 mW 5.1 J 49.4 I/mJ 35.7 s 940: 7987 8.5 C/MHz 164 mW 5.1 J 48.7 I/mJ 31.3 s 1056: 8954 8.5 C/MHz 185 mW 5.2 J 48.3 I/mJ 27.9 s 1171: 9944 8.5 C/MHz 212 mW 5.3 J 46.9 I/mJ 25.2 s 1286: 10926 8.5 C/MHz 235 mW 5.4 J 46.4 I/mJ 22.9 s 1382: 11735 8.5 C/MHz 253 mW 5.4 J 46.4 I/mJ 21.3 s 1478: 12531 8.5 C/MHz 277 mW 5.5 J 45.2 I/mJ 20.0 s 1574: 13335 8.5 C/MHz 306 mW 5.7 J 43.6 I/mJ 18.8 s 1670: 14169 8.5 C/MHz 335 mW 5.9 J 42.2 I/mJ 17.7 s 1766: 14969 8.5 C/MHz 353 mW 5.9 J 42.3 I/mJ 16.7 s 1862: 15800 8.5 C/MHz 444 mW 7.0 J 35.6 I/mJ 15.8 s 1958: 16630 8.5 C/MHz 463 mW 7.0 J 35.9 I/mJ 15.0 s 2054: 17428 8.5 C/MHz 480 mW 6.9 J 36.3 I/mJ 14.4 s 2150: 18238 8.5 C/MHz 496 mW 6.8 J 36.8 I/mJ 13.7 s 2246: 19053 8.5 C/MHz 578 mW 7.6 J 32.9 I/mJ 13.1 s 2342: 19873 8.5 C/MHz 625 mW 7.9 J 31.8 I/mJ 12.6 s 2419: 20522 8.5 C/MHz 675 mW 8.2 J 30.4 I/mJ 12.2 s ===== CPU 7 ===== Frequencies: 844 960 1075 1190 1305 1401 1516 1632 1747 1862 1977 2073 2169 2265 2361 2457 2553 2649 2745 2841 844: 7172 8.5 C/MHz 155 mW 5.4 J 46.4 I/mJ 34.9 s 960: 8148 8.5 C/MHz 172 mW 5.3 J 47.4 I/mJ 30.7 s 1075: 9116 8.5 C/MHz 197 mW 5.4 J 46.2 I/mJ 27.4 s 1190: 10105 8.5 C/MHz 220 mW 5.4 J 46.0 I/mJ 24.8 s 1305: 11084 8.5 C/MHz 242 mW 5.5 J 45.8 I/mJ 22.6 s 1401: 11888 8.5 C/MHz 262 mW 5.5 J 45.4 I/mJ 21.0 s 1516: 12859 8.5 C/MHz 297 mW 5.8 J 43.2 I/mJ 19.5 s 1632: 13840 8.5 C/MHz 335 mW 6.1 J 41.3 I/mJ 18.1 s 1747: 14827 8.5 C/MHz 369 mW 6.2 J 40.1 I/mJ 16.9 s 1862: 15800 8.5 C/MHz 395 mW 6.3 J 40.0 I/mJ 15.8 s 1977: 16786 8.5 C/MHz 443 mW 6.6 J 37.9 I/mJ 14.9 s 2073: 17566 8.5 C/MHz 488 mW 6.9 J 36.0 I/mJ 14.2 s 2169: 18395 8.5 C/MHz 620 mW 8.4 J 29.7 I/mJ 13.6 s 2265: 19223 8.5 C/MHz 621 mW 8.1 J 30.9 I/mJ 13.0 s 2361: 20040 8.5 C/MHz 672 mW 8.4 J 29.8 I/mJ 12.5 s 2457: 20852 8.5 C/MHz 696 mW 8.3 J 29.9 I/mJ 12.0 s 2553: 21684 8.5 C/MHz 738 mW 8.5 J 29.3 I/mJ 11.5 s 2649: 22458 8.5 C/MHz 793 mW 8.8 J 28.3 I/mJ 11.1 s 2745: 23314 8.5 C/MHz 875 mW 9.4 J 26.6 I/mJ 10.7 s 2841: 24103 8.5 C/MHz 928 mW 9.6 J 26.0 I/mJ 10.4 s [1] https://github.com/kdrag0n/freqbench [2] https://www.eembc.org/coremark/ [3] https://github.com/kdrag0n/freqbench/tree/master/results/sm8250/k30s Signed-off-by: Danny Lin Link: https://lore.kernel.org/r/20210112013255.415253-2-danny@kdrag0n.dev Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 8d5c5d44187a..20e70d5641ea 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -93,6 +93,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x0>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_0>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -110,6 +112,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x100>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_100>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -124,6 +128,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x200>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_200>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -138,6 +144,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x300>; enable-method = "psci"; + capacity-dmips-mhz = <448>; + dynamic-power-coefficient = <205>; next-level-cache = <&L2_300>; qcom,freq-domain = <&cpufreq_hw 0>; #cooling-cells = <2>; @@ -152,6 +160,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x400>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <379>; next-level-cache = <&L2_400>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -166,6 +176,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x500>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <379>; next-level-cache = <&L2_500>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -181,6 +193,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x600>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <379>; next-level-cache = <&L2_600>; qcom,freq-domain = <&cpufreq_hw 1>; #cooling-cells = <2>; @@ -195,6 +209,8 @@ compatible = "qcom,kryo485"; reg = <0x0 0x700>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; + dynamic-power-coefficient = <444>; next-level-cache = <&L2_700>; qcom,freq-domain = <&cpufreq_hw 2>; #cooling-cells = <2>; From bc19af98ba391aa04c2e3b070a1a28eac43c9143 Mon Sep 17 00:00:00 2001 From: Matthias Kaehlcke Date: Fri, 8 Jan 2021 14:16:50 -0800 Subject: [PATCH 228/584] arm64: dts: qcom: sc7180: Add labels for cpuN-thermal nodes Add labels to the cpuN-thermal nodes to allow board files to use a phandle instead replicating the node hierarchy when adjusting certain properties. Due to the 'sustainable-power' property CPU thermal zones are more likely to need property updates than other SC7180 zones, hence only labels for CPU zones are added for now. Reviewed-by: Douglas Anderson Signed-off-by: Matthias Kaehlcke Link: https://lore.kernel.org/r/20210108141648.1.Ia8019b8b303ca31a06752ed6ceb5c3ac50bd1d48@changeid Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180.dtsi | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 268fa40a1774..2bd06beafecc 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -3590,7 +3590,7 @@ }; thermal-zones { - cpu0-thermal { + cpu0_thermal: cpu0-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3639,7 +3639,7 @@ }; }; - cpu1-thermal { + cpu1_thermal: cpu1-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3688,7 +3688,7 @@ }; }; - cpu2-thermal { + cpu2_thermal: cpu2-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3737,7 +3737,7 @@ }; }; - cpu3-thermal { + cpu3_thermal: cpu3-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3786,7 +3786,7 @@ }; }; - cpu4-thermal { + cpu4_thermal: cpu4-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3835,7 +3835,7 @@ }; }; - cpu5-thermal { + cpu5_thermal: cpu5-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3884,7 +3884,7 @@ }; }; - cpu6-thermal { + cpu6_thermal: cpu6-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3925,7 +3925,7 @@ }; }; - cpu7-thermal { + cpu7_thermal: cpu7-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -3966,7 +3966,7 @@ }; }; - cpu8-thermal { + cpu8_thermal: cpu8-thermal { polling-delay-passive = <250>; polling-delay = <0>; @@ -4007,7 +4007,7 @@ }; }; - cpu9-thermal { + cpu9_thermal: cpu9-thermal { polling-delay-passive = <250>; polling-delay = <0>; From abf2c58aaa776cf43daf0fc4fd20082c71583c6b Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Thu, 17 Dec 2020 21:33:41 +0300 Subject: [PATCH 229/584] arm64: dts: qcom: qrb5165-rb5: fix uSD pins drive strength Lower drive strength for microSD data and CMD pins from 16 to 10. This fixes spurious card removal issues observed on some boards. Also this change allows us to re-enable 1.8V support, which seems to work with lowered drive strength. Signed-off-by: Dmitry Baryshkov Cc: Veerabhadrarao Badiganti Fixes: 53a8ccf1c7e5 ("arm64: dts: qcom: rb5: Add support for uSD card") Link: https://lore.kernel.org/r/20201217183341.3186402-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 7c2a798c6ac6..4a0c3edf87e1 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -660,8 +660,6 @@ vqmmc-supply = <&vreg_l6c_2p96>; cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; bus-width = <4>; - /* there seem to be issues with HS400-1.8V mode, so disable it */ - no-1-8-v; no-sdio; no-emmc; }; @@ -982,13 +980,13 @@ cmd { pins = "sdc2_cmd"; bias-pull-up; - drive-strength = <16>; + drive-strength = <10>; }; data { pins = "sdc2_data"; bias-pull-up; - drive-strength = <16>; + drive-strength = <10>; }; }; From f791f1a498fbef783e7711db9f597de7d85b661a Mon Sep 17 00:00:00 2001 From: Daniel Palmer Date: Sat, 12 Dec 2020 10:22:53 +0900 Subject: [PATCH 230/584] dt-bindings: vendor-prefixes: Fix misordering introduced by honestar prefix The prefix for honestar should come before honeywell. Fixes: 43181b5d8072 ("dt-bindings: vendor-prefixes: Add honestar vendor prefix") Signed-off-by: Daniel Palmer Link: https://lore.kernel.org/linux-arm-kernel/CAFr9PXmwOEuHHA-kDeL1YS8bWvovrt43MXxyy1J+hGbXwPUFSA@mail.gmail.com/ Link: https://lore.kernel.org/r/20201212012253.373074-1-daniel@0x0f.com' Signed-off-by: Arnd Bergmann --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 041ae90b0d8f..308512262009 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -467,10 +467,10 @@ patternProperties: description: Hitex Development Tools "^holt,.*": description: Holt Integrated Circuits, Inc. - "^honeywell,.*": - description: Honeywell "^honestar,.*": description: Honestar Technologies Co., Ltd. + "^honeywell,.*": + description: Honeywell "^hoperun,.*": description: Jiangsu HopeRun Software Co., Ltd. "^hp,.*": From 0fb56bf95c76f99d6301aea8f7198babd0005fa6 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Sat, 16 Jan 2021 03:23:46 +0300 Subject: [PATCH 231/584] arm64: dts: qcom: qrb5165-rb5: sort nodes alphabetically Move swr0 device node to keep alphabetical sorting order of device tree nodes. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210116002346.422479-1-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 40 ++++++++++++------------ 1 file changed, 20 insertions(+), 20 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 4a0c3edf87e1..a424595da8b0 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -664,26 +664,6 @@ no-emmc; }; -&swr0 { - left_spkr: wsa8810-left{ - compatible = "sdw10217211000"; - reg = <0 3>; - powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; - #thermal-sensor-cells = <0>; - sound-name-prefix = "SpkrLeft"; - #sound-dai-cells = <0>; - }; - - right_spkr: wsa8810-right{ - compatible = "sdw10217211000"; - reg = <0 4>; - powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; - #thermal-sensor-cells = <0>; - sound-name-prefix = "SpkrRight"; - #sound-dai-cells = <0>; - }; -}; - &sound { compatible = "qcom,qrb5165-rb5-sndcard"; pinctrl-0 = <&tert_mi2s_active>; @@ -780,6 +760,26 @@ }; }; +&swr0 { + left_spkr: wsa8810-left{ + compatible = "sdw10217211000"; + reg = <0 3>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrLeft"; + #sound-dai-cells = <0>; + }; + + right_spkr: wsa8810-right{ + compatible = "sdw10217211000"; + reg = <0 4>; + powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>; + #thermal-sensor-cells = <0>; + sound-name-prefix = "SpkrRight"; + #sound-dai-cells = <0>; + }; +}; + &tlmm { gpio-reserved-ranges = <40 4>; gpio-line-names = From 839661a2bbc8cde0b0ea838485076eec41c50502 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Thu, 7 Jan 2021 13:31:15 +0100 Subject: [PATCH 232/584] ARM: dts: imx7: Mark timer with arm,cpu-registers-not-fw-configured There is no firmware to initialize the arch timer register on all iMX7 systems, add arm,cpu-registers-not-fw-configured to let Linux do it. Signed-off-by: Marek Vasut Cc: Fabio Estevam Cc: NXP Linux Team To: linux-arm-kernel@lists.infradead.org Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx7s.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi index 251007a7b836..a22d41e0cf31 100644 --- a/arch/arm/boot/dts/imx7s.dtsi +++ b/arch/arm/boot/dts/imx7s.dtsi @@ -151,6 +151,7 @@ timer { compatible = "arm,armv7-timer"; + arm,cpu-registers-not-fw-configured; interrupt-parent = <&intc>; interrupts = , , From 93ef4e4156315679df448de2988f7a85698e37a0 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Thu, 7 Jan 2021 20:50:41 -0300 Subject: [PATCH 233/584] ARM: dts: imx6ul-14x14-evk: Fix SPI chipselect polarity The GPIO expander SPI chipselect is active low. Mark it as such to avoid the following warning: [ 6.839213] gpio@0 enforce active low on chipselect handle Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi index 64c2d1e9f7fc..a6dbfa85bb6a 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi @@ -101,7 +101,7 @@ status = "okay"; gpio-sck = <&gpio5 11 0>; gpio-mosi = <&gpio5 10 0>; - cs-gpios = <&gpio5 7 0>; + cs-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>; num-chipselects = <1>; #address-cells = <1>; #size-cells = <0>; From 70f04e9a3358404367030493dc36718d4495a9a5 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Thu, 7 Jan 2021 20:50:42 -0300 Subject: [PATCH 234/584] ARM: dts: imx6ul-14x14-evk: Enable the GPIO expander Currently the 74LV595PW GPIO expander is not functional because its OE pin is not driven low. Make it funcional by passing the 'enable-gpios' property inside the GPIO expander node. After putting the OE pin in low state, the outputs of the 74LV595PW all go low. The two KSZ8081 Ethernet PHYs reset lines are driven from the the GPIO expander and as they remain low, this causes the Ethernet PHYs not to be detected. There is one solution to this problem as suggested by Andrew Lunn: "Some devices will respond to MDIO while held in reset, some don't. If your PHYs don't you need to add a compatible of the form ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$ with the PHY ID. The PHY will then be probed, independent of if it can be found on the bus or not, and that probing will enable the GPIO." So pass the "ethernet-phy-id0022.1560" for the KSZ8081 PHYs so that they both can be functional after 74LV595PW is activated. Suggested-by: Andrew Lunn Signed-off-by: Fabio Estevam Reviewed-by: Andrew Lunn Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi index a6dbfa85bb6a..8bf845afd166 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi @@ -113,6 +113,7 @@ reg = <0>; registers-number = <1>; spi-max-frequency = <100000>; + enable-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; }; }; @@ -169,6 +170,7 @@ #size-cells = <0>; ethphy0: ethernet-phy@2 { + compatible = "ethernet-phy-id0022.1560"; reg = <2>; micrel,led-mode = <1>; clocks = <&clks IMX6UL_CLK_ENET_REF>; @@ -176,6 +178,7 @@ }; ethphy1: ethernet-phy@1 { + compatible = "ethernet-phy-id0022.1560"; reg = <1>; micrel,led-mode = <1>; clocks = <&clks IMX6UL_CLK_ENET2_REF>; From 2db7e78bf02b2d3ad8c917ded18e403f5774e39c Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Thu, 7 Jan 2021 20:50:43 -0300 Subject: [PATCH 235/584] ARM: dts: imx6ul-14x14-evk: Describe the KSZ8081 reset MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit There are two KSZ8081 on the imx6ul-14x14-evk: one has the reset line controlled by the Q1 output of the 74LV595PW expander, and the other by the Q2 output. The KSZ8081 datasheet states that the tsr parameter (Stable supply voltage (VDDIO, VDDA_3.3) to reset high) to be 10ms minimum and "After the de-assertion of reset, wait a minimum of 100 µs before starting programming on the MIIM (MDC/MDIO) interface." Describe these parameters in the devicetree. Signed-off-by: Fabio Estevam Reviewed-by: Andrew Lunn Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi index 8bf845afd166..ca8c658cfcba 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi @@ -175,6 +175,10 @@ micrel,led-mode = <1>; clocks = <&clks IMX6UL_CLK_ENET_REF>; clock-names = "rmii-ref"; + reset-gpios = <&gpio_spi 1 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <100>; + }; ethphy1: ethernet-phy@1 { @@ -183,6 +187,9 @@ micrel,led-mode = <1>; clocks = <&clks IMX6UL_CLK_ENET2_REF>; clock-names = "rmii-ref"; + reset-gpios = <&gpio_spi 2 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <100>; }; }; }; From e4cbd169b3a8b8fe772f1e7dc52c938188e2f55a Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Thu, 7 Jan 2021 20:50:44 -0300 Subject: [PATCH 236/584] ARM: dts: imx6ul-14x14-evk: Add camera support Add support for the OV5640 parallel camera module. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6ul-14x14-evk.dtsi | 42 ++++++++++++++++++++++++- 1 file changed, 41 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi index ca8c658cfcba..c593597b2119 100644 --- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi +++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi @@ -146,6 +146,41 @@ reg = <0x1a>; wlf,shared-lrclk; }; + + camera@3c { + compatible = "ovti,ov5640"; + reg = <0x3c>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_camera_clock>; + clocks = <&clks IMX6UL_CLK_CSI>; + clock-names = "xclk"; + powerdown-gpios = <&gpio_spi 6 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio_spi 5 GPIO_ACTIVE_LOW>; + + port { + ov5640_to_parallel: endpoint { + remote-endpoint = <¶llel_from_ov5640>; + bus-width = <8>; + data-shift = <2>; /* lines 9:2 are used */ + hsync-active = <0>; + vsync-active = <0>; + pclk-sample = <1>; + }; + }; + }; +}; + +&csi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_csi1>; + status = "okay"; + + port { + parallel_from_ov5640: endpoint { + remote-endpoint = <&ov5640_to_parallel>; + bus-type = <5>; /* Parallel bus */ + }; + }; }; &fec1 { @@ -353,9 +388,14 @@ &iomuxc { pinctrl-names = "default"; - pinctrl_csi1: csi1grp { + pinctrl_camera_clock: cameraclockgrp { fsl,pins = < MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088 + >; + }; + + pinctrl_csi1: csi1grp { + fsl,pins = < MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088 MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088 MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088 From 8900d0d59b63766c4ed10462eb921c4bd595e4c7 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 8 Jan 2021 23:09:58 +0000 Subject: [PATCH 237/584] arm64: dts: lx2160a-clearfog-itx: add power button support Add support for the power button. Signed-off-by: Russell King Signed-off-by: Shawn Guo --- .../boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi index f3741a32e868..2b63235ca627 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi @@ -8,6 +8,7 @@ /dts-v1/; #include "fsl-lx2160a-cex7.dtsi" +#include / { aliases { @@ -18,6 +19,17 @@ chosen { stdout-path = "serial0:115200n8"; }; + + gpio-keys { + compatible = "gpio-keys"; + + key { + label = "power"; + linux,can-disable; + linux,code = ; + gpios = <&gpio2 6 GPIO_ACTIVE_LOW>; + }; + }; }; &emdio2 { From e8d08d80f4508e0601ea2beb0848b5a60d6a2c31 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 10 Jan 2021 05:38:26 -0600 Subject: [PATCH 238/584] arm64: dts: imx8mm-beacon: add more pinctrl states for usdhc1 The WiFi chip is capable of communication at SDR104 speeds. Enable 100Mhz and 200MHz pinmux to support this. Signed-off-by: Adam Ford Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi index d897913537ca..988f8ab679ad 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi @@ -256,8 +256,10 @@ &usdhc1 { #address-cells = <1>; #size-cells = <0>; - pinctrl-names = "default"; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; bus-width = <4>; non-removable; cap-power-off-card; From 18b9de73f06e474456699bd743a054de9b905706 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sun, 10 Jan 2021 05:53:53 -0600 Subject: [PATCH 239/584] arm64: dts: imx8mn-beacon-som: Configure RTC aliases On the i.MX8MN Beacon SOM, there is an RTC chip which is fed power from the baseboard during power off. The SNVS RTC integrated into the SoC is not fed power. Depending on the order the modules are loaded, this can be a problem if the external RTC isn't rtc0. Make the alias for rtc0 point to the external RTC all the time and rtc1 point to the SVNS in order to correctly hold date/time over a power-cycle. Signed-off-by: Adam Ford Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi index 67e5e5b9ddea..2120e6485393 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi @@ -4,6 +4,11 @@ */ / { + aliases { + rtc0 = &rtc; + rtc1 = &snvs_rtc; + }; + usdhc1_pwrseq: usdhc1_pwrseq { compatible = "mmc-pwrseq-simple"; pinctrl-names = "default"; @@ -212,7 +217,7 @@ reg = <0x50>; }; - rtc@51 { + rtc: rtc@51 { compatible = "nxp,pcf85263"; reg = <0x51>; }; From 12dffe14e372ab7af26c12ca4cc91876a0fb7b41 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 10 Jan 2021 13:58:15 +0000 Subject: [PATCH 240/584] arm64: dts: lx2160a-cex7: delete RTC interrupt The RTC interrupt is incorrect and prevents the RTC driver initialising. In any case, the PCF2127 driver wants an active low interrupt, which neither the GIC nor the GPIO blocks support. There is an ISPPT block in the LX2160A, but this is not supported in mainline kernels. So, just delete the interrupt. Signed-off-by: Russell King Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi index d87d16460875..49fcf025494f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi @@ -134,8 +134,6 @@ rtc@51 { compatible = "nxp,pcf2129"; reg = <0x51>; - // IRQ10_B - interrupts = ; }; }; From 5dd74cf8f3e68fa46a253804ac42e9d3f4f58885 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Sun, 10 Jan 2021 20:54:54 +0100 Subject: [PATCH 241/584] arm64: dts: freescale: sl28: enable SATA support With a newer bootloader SATA might be used in a mPCI slot using a mSATA card. Enable the SATA controller on the Kontron K-Box LS-230-A which comes with such a slot. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- .../boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts index d66d8b2c3d1a..6b575efd84a7 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts @@ -107,3 +107,7 @@ ethernet = <&enetc_port2>; status = "okay"; }; + +&sata { + status = "okay"; +}; From 8b6b17540370415889fb1a7170bc8c4dba18edd6 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Fri, 8 Jan 2021 09:47:26 -0300 Subject: [PATCH 242/584] arm64: dts: imx8mq: Add eCSPI DMA support eCSPI ports have DMA capability. Describe the eCSPI DMA properties. Signed-off-by: Fabio Estevam Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index c9874dfe0cd4..4ef8c92403dd 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -835,6 +835,8 @@ clocks = <&clk IMX8MQ_CLK_ECSPI1_ROOT>, <&clk IMX8MQ_CLK_ECSPI1_ROOT>; clock-names = "ipg", "per"; + dmas = <&sdma1 0 7 1>, <&sdma1 1 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -847,6 +849,8 @@ clocks = <&clk IMX8MQ_CLK_ECSPI2_ROOT>, <&clk IMX8MQ_CLK_ECSPI2_ROOT>; clock-names = "ipg", "per"; + dmas = <&sdma1 2 7 1>, <&sdma1 3 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -859,6 +863,8 @@ clocks = <&clk IMX8MQ_CLK_ECSPI3_ROOT>, <&clk IMX8MQ_CLK_ECSPI3_ROOT>; clock-names = "ipg", "per"; + dmas = <&sdma1 4 7 1>, <&sdma1 5 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; From aaad900757a66706bb7a7b2be5f57424228aab2c Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 3 Jan 2021 04:00:06 -0600 Subject: [PATCH 243/584] arm64: dts: allwinner: h6: Add RSB controller node The H6 SoC contains an undocumented but fully functional RSB controller. Add support for it. The MMIO register address matches other SoCs of the same generation, and the IRQ matches a hole in the documented IRQ list. Signed-off-by: Samuel Holland Acked-by: Maxime Ripard [wens@csie.org: Use raw numbers instead of macros for clock/reset index] Signed-off-by: Chen-Yu Tsai --- arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi index 77765d4a05ec..49e979794094 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi @@ -956,6 +956,11 @@ pins = "PL9"; function = "s_cir_rx"; }; + + r_rsb_pins: r-rsb-pins { + pins = "PL0", "PL1"; + function = "s_rsb"; + }; }; r_ir: ir@7040000 { @@ -986,6 +991,20 @@ #size-cells = <0>; }; + r_rsb: rsb@7083000 { + compatible = "allwinner,sun8i-a23-rsb"; + reg = <0x07083000 0x400>; + interrupts = ; + clocks = <&r_ccu 13>; + clock-frequency = <3000000>; + resets = <&r_ccu 7>; + pinctrl-names = "default"; + pinctrl-0 = <&r_rsb_pins>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + ths: thermal-sensor@5070400 { compatible = "allwinner,sun50i-h6-ths"; reg = <0x05070400 0x100>; From b67b3c9b66372c9d3d5ff20738dd2212ccb38f86 Mon Sep 17 00:00:00 2001 From: Paul Kocialkowski Date: Fri, 18 Dec 2020 20:50:33 +0100 Subject: [PATCH 244/584] ARM: dts: sun8i-v3s: Add CSI0 MCLK pin definition This adds a device-tree definition for the CSI0 MCLK pin, which can be used for feeding MIPI CSI-2 sensors. Signed-off-by: Paul Kocialkowski Signed-off-by: Chen-Yu Tsai --- arch/arm/boot/dts/sun8i-v3s.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index b7b0e685e26b..eb4cb63fef13 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -337,6 +337,12 @@ interrupt-controller; #interrupt-cells = <3>; + /omit-if-no-ref/ + csi0_mclk_pin: csi0-mclk-pin { + pins = "PE20"; + function = "csi_mipi"; + }; + /omit-if-no-ref/ csi1_8bit_pins: csi1-8bit-pins { pins = "PE0", "PE2", "PE3", "PE8", "PE9", From 18df346b66e56eb51fa423bda3fe4d413a7028ff Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 11 Jan 2021 11:18:51 +0100 Subject: [PATCH 245/584] dt-bindings: vendor-prefixes: Add an entry for Kverneland Group Add "kvg" entry for Kverneland Group: https://ien.kvernelandgroup.com/ Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index f03ba0c4ae5e..115d859927f8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -581,6 +581,8 @@ patternProperties: description: Kontron S&T AG "^kosagi,.*": description: Sutajio Ko-Usagi PTE Ltd. + "^kvg,.*": + description: Kverneland Group "^kyo,.*": description: Kyocera Corporation "^lacie,.*": From 55d743d1067bea8630c885b4f0078c66205ea005 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 11 Jan 2021 11:18:52 +0100 Subject: [PATCH 246/584] dt-bindings: arm: fsl: add Kverneland UT1, UT1Q and UI1P boards Add Kverneland UT1 (imx6dl), UT1Q (imx6q) and UT1P (imx6dp) based boards Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 89ef175ee49f..2eced2f84df2 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -210,6 +210,7 @@ properties: - kiebackpeter,imx6q-tpc # K+P i.MX6 Quad TPC Board - kontron,imx6q-samx6i # Kontron i.MX6 Dual/Quad SMARC Module - kosagi,imx6q-novena # Kosagi Novena Dual/Quad + - kvg,vicut1q # Kverneland UT1Q board - logicpd,imx6q-logicpd - lwn,display5 # Liebherr Display5 i.MX6 Quad Board - lwn,mccmon6 # Liebherr Monitor6 i.MX6 Quad Board @@ -331,6 +332,7 @@ properties: - fsl,imx6qp-sabreauto # i.MX6 Quad Plus SABRE Automotive Board - fsl,imx6qp-sabresd # i.MX6 Quad Plus SABRE Smart Device Board - karo,imx6qp-tx6qp # Ka-Ro electronics TX6QP-8037 Module + - kvg,vicutp # Kverneland UT1P board - prt,prtwd3 # Protonic WD3 board - wand,imx6qp-wandboard # Wandboard i.MX6 QuadPlus Board - zii,imx6qp-zii-rdu2 # ZII RDU2+ Board @@ -364,6 +366,7 @@ properties: - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules - kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module + - kvg,vicut1 # Kverneland UT1 board - ply,plybas # Plymovent BAS board - ply,plym2m # Plymovent M2M board - poslab,imx6dl-savageboard # Poslab SavageBoard Dual From 6e73bfbb2ed099da744587cbd0b5416ce378c575 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 11 Jan 2021 11:18:54 +0100 Subject: [PATCH 247/584] dt-bindings: arm: fsl: add Kverneland TGO board Add Kverneland TGO imx6dl based board Signed-off-by: Oleksij Rempel Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 2eced2f84df2..65038b16302e 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -366,6 +366,7 @@ properties: - fsl,imx6dl-sabresd # i.MX6 DualLite SABRE Smart Device Board - karo,imx6dl-tx6dl # Ka-Ro electronics TX6U Modules - kontron,imx6dl-samx6i # Kontron i.MX6 Solo SMARC Module + - kvg,victgo # Kverneland TGO - kvg,vicut1 # Kverneland UT1 board - ply,plybas # Plymovent BAS board - ply,plym2m # Plymovent M2M board From db8c29bae60ad63b111466344f329d17f4117e76 Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 11 Jan 2021 11:18:53 +0100 Subject: [PATCH 248/584] ARM: dts: add Kverneland UT1, UT1Q and UT1P VICUT1(Q,P) is the Kverneland UT1(Q,P) IsoBus universal terminal for agricultural applications on tractors. Co-Developed-by: David Jander Signed-off-by: David Jander Signed-off-by: Oleksij Rempel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 3 + arch/arm/boot/dts/imx6dl-vicut1.dts | 13 + arch/arm/boot/dts/imx6q-vicut1.dts | 17 + arch/arm/boot/dts/imx6qdl-vicut1.dtsi | 803 ++++++++++++++++++++++++++ arch/arm/boot/dts/imx6qp-vicutp.dts | 13 + 5 files changed, 849 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-vicut1.dts create mode 100644 arch/arm/boot/dts/imx6q-vicut1.dts create mode 100644 arch/arm/boot/dts/imx6qdl-vicut1.dtsi create mode 100644 arch/arm/boot/dts/imx6qp-vicutp.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 8b422215df4b..4ed61e88d7ba 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -490,6 +490,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-tx6u-811x.dtb \ imx6dl-tx6u-81xx-mb7.dtb \ imx6dl-udoo.dtb \ + imx6dl-vicut1.dtb \ imx6dl-wandboard.dtb \ imx6dl-wandboard-revb1.dtb \ imx6dl-wandboard-revd1.dtb \ @@ -583,6 +584,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6q-udoo.dtb \ imx6q-utilite-pro.dtb \ imx6q-var-dt6customboard.dtb \ + imx6q-vicut1.dtb \ imx6q-wandboard.dtb \ imx6q-wandboard-revb1.dtb \ imx6q-wandboard-revd1.dtb \ @@ -597,6 +599,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6qp-tx6qp-8037-mb7.dtb \ imx6qp-tx6qp-8137.dtb \ imx6qp-tx6qp-8137-mb7.dtb \ + imx6qp-vicutp.dtb \ imx6qp-wandboard-revd1.dtb \ imx6qp-zii-rdu2.dtb dtb-$(CONFIG_SOC_IMX6SL) += \ diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts new file mode 100644 index 000000000000..174fd913bf96 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-vicut1.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2014 Protonic Holland + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-vicut1.dtsi" + +/ { + model = "Kverneland UT1 Board"; + compatible = "kvg,vicut1", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts new file mode 100644 index 000000000000..0a4e251be162 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-vicut1.dts @@ -0,0 +1,17 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2014 Protonic Holland + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-vicut1.dtsi" + +/ { + model = "Kverneland UT1Q Board"; + compatible = "kvg,vicut1q", "fsl,imx6q"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi new file mode 100644 index 000000000000..eb25d21a2ace --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi @@ -0,0 +1,803 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2014 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel , Pengutronix + */ + +#include +#include +#include +#include +#include +#include + +/ { + chosen { + stdout-path = &uart4; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight>; + pwms = <&pwm1 0 5000000 0>; + brightness-levels = <0 16 64 255>; + num-interpolated-steps = <16>; + default-brightness-level = <1>; + power-supply = <®_3v3>; + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + }; + + connector { + compatible = "composite-video-connector"; + label = "Composite0"; + sdtv-standards = ; + + port { + comp0_out: endpoint { + remote-endpoint = <&tvp5150_comp0_in>; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + + power { + label = "Power Button"; + gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + linux,code = ; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "LED_DI0_DEBUG_0"; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "LED_DI0_DEBUG_1"; + function = LED_FUNCTION_DISK; + gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "disk-activity"; + }; + + led-2 { + label = "POWER_LED"; + function = LED_FUNCTION_POWER; + gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + panel { + compatible = "kyo,tcg121xglp"; + backlight = <&backlight>; + power-supply = <®_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_h1_vbus: regulator-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "h1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_otg_vbus: regulator-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "otg-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_wifi: regulator-wifi { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wifi_npd>; + regulator-name = "wifi"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>; + enable-active-high; + startup-delay-us = <70000>; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "prti6q-sgtl5000"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Line", "Line In Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "External Speaker", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&ssi1>; + system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */ + }; + + simple-audio-card,codec { + sound-dai = <&codec>; + bitclock-master; + frame-master; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; + + mux-ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN 0 + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TFSDIR 0 + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) + >; + }; + + mux-pins3 { + fsl,audmux-port = <2>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) + 0 IMX_AUDMUX_V2_PDCR_TXRXEN + >; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii-id"; + phy-handle = <&rgmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ9031RNX PHY */ + rgmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR", + "CAM2_MIRROR", "", "", "SMBALERT", + "DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3", + "SDIO_D2", "SDIO_D1", "SDIO_D0", + "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK", + "SD1_DATA3", "", "", + "", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "", + "WL_IRQ", "ETH_MDC"; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4", + "BOARD_ID0", "BOARD_ID1", "BOARD_ID2", + "", "", "", "", "", "", "", "ON_SWITCH", + "POWER_LED", "", "ECSPI2_SS0", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1", + "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ", + "", "", "", "", "", "", "", ""; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "UART4_TXD", "UART4_RXD", + "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR", + "CAN2_SR", "CAN2_TX", "CAN2_RX", + "LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "", + "", "", "", "", "BL_EN", "BL_PWM", "", ""; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS", + "PCIE_RESET", "", "", "", "", "", "", "", + "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET", + "I2S_BITCLK", "I2S_DOUT", + "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX", + "YACO_AUX_TX", "ITU656_D0", "ITU656_D1"; +}; + +&gpio6 { + gpio-line-names = + "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5", + "ITU656_D6", "ITU656_D7", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2", + "RGMII_TD3", + "RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1", + "RGMII_RD2", "RGMII_RD3", "", ""; +}; + +&gpio7 { + gpio-line-names = + "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0", + "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3", + "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "", + "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "", + "", "", "", "", "", "", "", ""; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: audio-codec@a { + compatible = "fsl,sgtl5000"; + reg = <0xa>; + #sound-dai-cells = <0>; + clocks = <&clks 201>; + VDDA-supply = <®_3v3>; + VDDIO-supply = <®_3v3>; + VDDD-supply = <®_1v8>; + }; + + video-decoder@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tvp5150_comp0_in: endpoint { + remote-endpoint = <&comp0_out>; + }; + }; + + /* Output port 2 is video output pad */ + port@2 { + reg = <2>; + + tvp5151_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + adc@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@5 { + reg = <5>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@6 { + reg = <6>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@7 { + reg = <7>; + ti,gain = <3>; + ti,datarate = <3>; + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&ipu1_csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_csi0>; + status = "okay"; +}; + +&ipu1_csi0_mux_from_parallel_sensor { + remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&ssi1 { + #sound-dai-cells = <0>; + fsl,mode = "ac97-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_h1_vbus>; + pinctrl-names = "default"; + phy_type = "utmi"; + dr_mode = "host"; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + vmmc-supply = <®_wifi>; + non-removable; + cap-power-off-card; + keep-power-in-suspend; + no-1-8-v; + no-mmc; + no-sd; + status = "okay"; + + wifi { + compatible = "ti,wl1271"; + interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>; + ref-clock-frequency = "38400000"; + tcxo-clock-frequency = "19200000"; + }; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_backlight: backlightgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000 + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008 + /* CAN2_SR */ + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030 + /* Phy reset */ + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1 + >; + }; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* ITU656_nRESET */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 + /* CAM1_MIRROR */ + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0 + /* CAM2_MIRROR */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0 + /* CAM_nDETECT */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + /* nON_SWITCH */ + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0 + /* ISB_IN1 */ + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0 + /* ISB_nIN2 */ + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 + /* WARN_LIGHT */ + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0 + /* ON2_FB */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 + /* YACO_nIRQ */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 + /* YACO_BOOT0 */ + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 + /* YACO_nRESET */ + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 + /* FORCE_ON1 */ + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + /* AUDIO_nRESET */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 + /* ITU656_nPDN */ + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 + + /* HW revision detect */ + /* REV_ID0 */ + MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 + /* REV_ID1 */ + MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 + /* REV_ID2 */ + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 + /* REV_ID3 */ + MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 + /* REV_ID4 */ + MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 + + /* New in HW revision 1 */ + /* ON1_FB */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 + /* DIP1_FB */ + MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 + + /* New in UT2: FIXME: ISB PWM should start off, PD */ + /* ISB_LED_PWM */ + MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x130b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_csi0: ipu1csi0grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + /* DEBUG0 */ + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0 + /* DEBUG1 */ + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0 + /* POWER_LED */ + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + >; + }; + + /* YaCO AUX Uart */ + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1 + >; + }; + + /* YaCO Touchscreen UART */ + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9 + /* WL12xx IRQ */ + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; + + pinctrl_wifi_npd: wifinpdgrp { + fsl,pins = < + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0 + >; + }; +}; diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts new file mode 100644 index 000000000000..7bad7ca6b12e --- /dev/null +++ b/arch/arm/boot/dts/imx6qp-vicutp.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2014 Protonic Holland + */ + +/dts-v1/; +#include "imx6qp.dtsi" +#include "imx6qdl-vicut1.dtsi" + +/ { + model = "Kverneland UT1P Board"; + compatible = "kvg,vicutp", "fsl,imx6qp"; +}; From 7f8f6311ba59582cb1c541d83d2b505a09907e6f Mon Sep 17 00:00:00 2001 From: Oleksij Rempel Date: Mon, 11 Jan 2021 11:18:55 +0100 Subject: [PATCH 249/584] ARM: dts: add Kverneland TGO board VICTGO is the Kverneland TGO IsoBus universal terminal for agricultural applications on tractors Co-Developed-by: David Jander Signed-off-by: David Jander Signed-off-by: Oleksij Rempel Signed-off-by: Shawn Guo --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx6dl-victgo.dts | 852 ++++++++++++++++++++++++++++ 2 files changed, 853 insertions(+) create mode 100644 arch/arm/boot/dts/imx6dl-victgo.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 4ed61e88d7ba..2f217f4d9732 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -490,6 +490,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ imx6dl-tx6u-811x.dtb \ imx6dl-tx6u-81xx-mb7.dtb \ imx6dl-udoo.dtb \ + imx6dl-victgo.dtb \ imx6dl-vicut1.dtb \ imx6dl-wandboard.dtb \ imx6dl-wandboard-revb1.dtb \ diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts new file mode 100644 index 000000000000..d37ba4ed847d --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-victgo.dts @@ -0,0 +1,852 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* + * Copyright (c) 2016 Protonic Holland + * Copyright (c) 2020 Oleksij Rempel , Pengutronix + */ + +/dts-v1/; +#include +#include +#include +#include +#include +#include +#include "imx6dl.dtsi" + +/ { + model = "Kverneland TGO"; + compatible = "kvg,victgo", "fsl,imx6dl"; + + chosen { + stdout-path = &uart4; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_backlight>; + pwms = <&pwm1 0 5000000 0>; + brightness-levels = <0 16 64 255>; + num-interpolated-steps = <16>; + default-brightness-level = <1>; + power-supply = <®_3v3>; + enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; + }; + + connector { + compatible = "composite-video-connector"; + label = "Composite0"; + sdtv-standards = ; + + port { + comp0_out: endpoint { + remote-endpoint = <&tvp5150_comp0_in>; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpiokeys>; + autorepeat; + + power { + label = "Power Button"; + gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + linux,code = ; + wakeup-source; + }; + + enter { + label = "Rotary Key"; + gpios = <&gpio2 05 GPIO_ACTIVE_LOW>; + linux,code = ; + wakeup-source; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_leds>; + + led-0 { + label = "debug0"; + function = LED_FUNCTION_HEARTBEAT; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "debug1"; + function = LED_FUNCTION_DISK; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "disk-activity"; + }; + + led-2 { + label = "power_led"; + function = LED_FUNCTION_POWER; + gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + panel { + compatible = "kyo,tcg121xglp"; + backlight = <&backlight>; + power-supply = <®_3v3>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + clk50m_phy: phy-clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <50000000>; + }; + + reg_1v8: regulator-1v8 { + compatible = "regulator-fixed"; + regulator-name = "1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + regulator-name = "3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_h1_vbus: regulator-h1-vbus { + compatible = "regulator-fixed"; + regulator-name = "h1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_otg_vbus: regulator-otg-vbus { + compatible = "regulator-fixed"; + regulator-name = "otg-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + rotary-encoder { + compatible = "rotary-encoder"; + pinctrl-0 = <&pinctrl_rotary_ch>; + gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>, + <&gpio2 4 GPIO_ACTIVE_HIGH>; + linux,axis = ; + rotary-encoder,steps-per-period = <4>; + rotary-encoder,relative-axis; + rotary-encoder,rollover; + wakeup-source; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "prti6q-sgtl5000"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Line", "Line In Jack", + "Headphone", "Headphone Jack", + "Speaker", "External Speaker"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "External Speaker", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&ssi1>; + system-clock-frequency = <0>; + }; + + simple-audio-card,codec { + sound-dai = <&codec>; + bitclock-master; + frame-master; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; + + mux-ssi1 { + fsl,audmux-port = <0>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN 0 + IMX_AUDMUX_V2_PTCR_TFSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TCSEL(2) 0 + IMX_AUDMUX_V2_PTCR_TFSDIR 0 + IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2) + >; + }; + + mux-pins3 { + fsl,audmux-port = <2>; + fsl,port-config = < + IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0) + 0 IMX_AUDMUX_V2_PDCR_TXRXEN + >; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>; + assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>; +}; + +&ecspi1 { + cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <20000000>; + }; +}; + +&ecspi2 { + cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + status = "okay"; + + touchscreen@0 { + compatible = "ti,tsc2046"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touchscreen>; + spi-max-frequency = <200000>; + interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>; + pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <800>; + touchscreen-size-y = <480>; + touchscreen-inverted-y; + touchscreen-max-pressure = <4095>; + ti,vref-delay-usecs = /bits/ 16 <100>; + ti,x-plate-ohms = /bits/ 16 <800>; + ti,y-plate-ohms = /bits/ 16 <300>; + wakeup-source; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rmii"; + clocks = <&clks IMX6QDL_CLK_ENET>, + <&clks IMX6QDL_CLK_ENET>, + <&clk50m_phy>; + clock-names = "ipg", "ahb", "ptp"; + phy-handle = <&rmii_phy>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Microchip KSZ8081RNA PHY */ + rmii_phy: ethernet-phy@0 { + reg = <0>; + interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <300>; + }; + }; +}; + +&gpio1 { + gpio-line-names = + "CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR", + "CAM2_MIRROR", "", "", "SMBALERT", + "DEBUG_0", "DEBUG_1", "", "", "", "", "", "", + "SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK", + "SD1_DATA3", "", "", + "", "", "", "", "", "", "", ""; +}; + +&gpio2 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4", + "BOARD_ID0", "BOARD_ID1", "BOARD_ID2", + "", "", "", "", "", "", "ISB_IN1", "ON_SWITCH", + "POWER_LED", "", "", "", "", "", "", ""; +}; + +&gpio3 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1", + "CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ", + "TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0", + "YACO_RESET"; +}; + +&gpio4 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX", + "", "", "DIP1_FB", "", "VCAM_EN", "", "", "", + "CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN", + "BL_PWM", "ETH_INTRP", "ISB_LED"; +}; + +&gpio5 { + gpio-line-names = + "", "", "", "", "", "", "", "", + "TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO", + "ECSPI2_SS0", "ECSPI2_SCLK", "", "", + "", "", "", "", "", "", "", "", + "I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX", + "YACO_AUX_TX", "ITU656_D0", "ITU656_D1"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: audio-codec@a { + compatible = "fsl,sgtl5000"; + reg = <0xa>; + #sound-dai-cells = <0>; + clocks = <&clks 201>; + VDDA-supply = <®_3v3>; + VDDIO-supply = <®_3v3>; + VDDD-supply = <®_1v8>; + }; + + video-decoder@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + tvp5150_comp0_in: endpoint { + remote-endpoint = <&comp0_out>; + }; + }; + + /* Output port 2 is video output pad */ + port@2 { + reg = <2>; + + tvp5151_to_ipu1_csi0_mux: endpoint { + remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>; + }; + }; + }; + + keypad@70 { + compatible = "holtek,ht16k33"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_keypad>; + reg = <0x70>; + refresh-rate-hz = <20>; + debounce-delay-ms = <50>; + interrupts-extended = <&gpio4 5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>; + keypad,num-rows = <12>; + keypad,num-columns = <3>; + linux,keymap = < + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(3, 0, KEY_F8) + MATRIX_KEY(4, 0, KEY_F10) + MATRIX_KEY(5, 0, KEY_F4) + MATRIX_KEY(6, 0, KEY_F2) + MATRIX_KEY(2, 1, KEY_F5) + MATRIX_KEY(3, 1, KEY_F7) + MATRIX_KEY(4, 1, KEY_F9) + MATRIX_KEY(5, 1, KEY_F3) + MATRIX_KEY(6, 1, KEY_F1) + >; + }; + + /* additional i2c devices are added automatically by the boot loader */ +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + adc@49 { + compatible = "ti,ads1015"; + reg = <0x49>; + #address-cells = <1>; + #size-cells = <0>; + + channel@4 { + reg = <4>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@5 { + reg = <5>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@6 { + reg = <6>; + ti,gain = <3>; + ti,datarate = <3>; + }; + + channel@7 { + reg = <7>; + ti,gain = <3>; + ti,datarate = <3>; + }; + }; + + rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; + + temperature-sensor@70 { + compatible = "ti,tmp103"; + reg = <0x70>; + }; +}; + +&ipu1_csi0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu1_csi0>; + status = "okay"; +}; + +&ipu1_csi0_mux_from_parallel_sensor { + remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + status = "okay"; + + port@4 { + reg = <4>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&ssi1 { + #sound-dai-cells = <0>; + fsl,mode = "ac97-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_h1_vbus>; + pinctrl-names = "default"; + phy_type = "utmi"; + dr_mode = "host"; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + phy_type = "utmi"; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + no-1-8-v; + disable-wp; + cap-sd-highspeed; + no-mmc; + no-sdio; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <8>; + no-1-8-v; + non-removable; + no-sd; + no-sdio; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0 + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_backlight: backlightgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x3008 + /* CAN1_SR */ + MX6QDL_PAD_KEY_COL3__GPIO4_IO12 0x13008 + /* CAN1_TERM */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b088 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b000 + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x3008 + /* CAN2_SR */ + MX6QDL_PAD_KEY_ROW3__GPIO4_IO13 0x13008 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + /* CS */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12 0x100b1 + MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK 0x100b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + /* MX6QDL_ENET_PINGRP4 */ + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0 0x1b0b0 + MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1 0x1b0b0 + MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26 0x1b0b0 + /* nINTRP */ + MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30 0x1b0b0 + >; + }; + + pinctrl_gpiokeys: gpiokeygrp { + fsl,pins = < + /* ROTARY_BTN */ + MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x1b0b0 + /* nON_SWITCH */ + MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x1b0b0 + >; + }; + + pinctrl_hog: hoggrp { + fsl,pins = < + /* ITU656_nRESET */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b0b0 + /* CAM1_MIRROR */ + MX6QDL_PAD_GPIO_3__GPIO1_IO03 0x130b0 + /* CAM2_MIRROR */ + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x130b0 + /* CAM_nDETECT */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b0b0 + /* ISB_IN1 */ + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x130b0 + /* ISB_nIN2 */ + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x1b0b0 + /* WARN_LIGHT */ + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x100b0 + /* ON2_FB */ + MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b0 + /* YACO_nIRQ */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x1b0b0 + /* YACO_BOOT0 */ + MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x130b0 + /* YACO_nRESET */ + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x1b0b0 + /* FORCE_ON1 */ + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0 + /* AUDIO_nRESET */ + MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x1f0b0 + /* ITU656_nPDN */ + MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b0b0 + + /* HW revision detect */ + /* REV_ID0 */ + MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0 + /* REV_ID1 is shared with PWM3 */ + /* REV_ID2 */ + MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 + /* REV_ID3 */ + MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x1b0b0 + /* REV_ID4 */ + MX6QDL_PAD_SD4_DAT4__GPIO2_IO12 0x1b0b0 + + /* New in HW revision 1 */ + /* ON1_FB */ + MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x100b0 + /* DIP1_FB */ + MX6QDL_PAD_DI0_PIN2__GPIO4_IO18 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_ipu1_csi0: ipu1csi0grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x1b0b0 + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x1b0b0 + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x1b0b0 + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x1b0b0 + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x1b0b0 + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x1b0b0 + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x1b0b0 + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x1b0b0 + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x1b0b0 + >; + }; + + pinctrl_keypad: keypadgrp { + fsl,pins = < + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_leds: ledsgrp { + fsl,pins = < + /* DEBUG0 */ + MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16 0x1b0b0 + /* DEBUG1 */ + MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x1b0b0 + /* POWER_LED */ + MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x1b0b0 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b0 + >; + }; + + pinctrl_rotary_ch: rotarychgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 + >; + }; + + pinctrl_touchscreen: touchscreengrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08 0x1b0b0 + MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x1b0b0 + >; + }; + + /* YaCO AUX Uart */ + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + /* YaCO Touchscreen UART */ + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099 + MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1 + >; + }; +}; From 69c910d3675fc44ed8e387c816afb79d54371314 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 11 Jan 2021 12:45:55 +0100 Subject: [PATCH 250/584] arm64: dts: ls1028a: fix FlexSPI clock Now that we have a proper driver for the FlexSPI interface use it. This will fix SCK frequency switching on Layerscape SoCs. This was tested on the Kontron sl28 board. Signed-off-by: Michael Walle Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 401badb713c3..045739dbcb17 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -206,9 +206,20 @@ }; dcfg: syscon@1e00000 { - compatible = "fsl,ls1028a-dcfg", "syscon"; + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,ls1028a-dcfg", "syscon", "simple-mfd"; reg = <0x0 0x1e00000 0x0 0x10000>; + ranges = <0x0 0x0 0x1e00000 0x10000>; little-endian; + + fspi_clk: clock-controller@900 { + compatible = "fsl,ls1028a-flexspi-clk"; + reg = <0x900 0x4>; + #clock-cells = <0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 0>; + clock-output-names = "fspi_clk"; + }; }; rst: syscon@1e60000 { @@ -326,8 +337,7 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = ; - clocks = <&clockgen QORIQ_CLK_HWACCEL 0>, - <&clockgen QORIQ_CLK_HWACCEL 0>; + clocks = <&fspi_clk>, <&fspi_clk>; clock-names = "fspi_en", "fspi"; status = "disabled"; }; From 4dec146131c592196df579a321b9d6ec7c41d7cd Mon Sep 17 00:00:00 2001 From: Andreas Kemnade Date: Wed, 13 Jan 2021 00:15:45 +0100 Subject: [PATCH 251/584] ARM: dts: imx6sl-tolino-shine2hd: correct console uart pinmux Configuration was correct enough to work with the pre-configuration done by uboot. While at it, also document the location. Signed-off-by: Andreas Kemnade Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts index caa279608803..e17c75c360f2 100644 --- a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts +++ b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts @@ -396,7 +396,7 @@ pinctrl_uart1: uart1grp { fsl,pins = < MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1 - MX6SL_PAD_UART1_RXD__UART1_TX_DATA 0x1b0b1 + MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1 >; }; @@ -543,6 +543,7 @@ }; &uart1 { + /* J4, through-holes */ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; status = "okay"; From b34af2eef6ac78c8734879fa2f8fadb85cd1145f Mon Sep 17 00:00:00 2001 From: Andreas Kemnade Date: Wed, 13 Jan 2021 00:15:46 +0100 Subject: [PATCH 252/584] ARM: dts: imx6sl-tolino-shine2hd: add second uart There is another uart next to the console uart used by vendor uboot and kernel, enable it and document its location. Signed-off-by: Andreas Kemnade Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts | 15 ++++++++++++++- 1 file changed, 14 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts index e17c75c360f2..6ea5f918d059 100644 --- a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts +++ b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts @@ -340,7 +340,6 @@ MX6SL_PAD_KEY_ROW7__GPIO4_IO07 0x79 MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x79 MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x79 - MX6SL_PAD_KEY_ROW6__GPIO4_IO05 0x79 >; }; @@ -400,6 +399,13 @@ >; }; + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1 + MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1 + >; + }; + pinctrl_usbotg1: usbotg1grp { fsl,pins = < MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059 @@ -549,6 +555,13 @@ status = "okay"; }; +&uart4 { + /* TP198, next to J4, SMD pads */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; pinctrl-0 = <&pinctrl_usdhc2>; From 035a3e167b094c09bab401b21f32e1d227c78fff Mon Sep 17 00:00:00 2001 From: Andreas Kemnade Date: Wed, 13 Jan 2021 00:15:48 +0100 Subject: [PATCH 253/584] ARM: dts: imx6sl-tolino-shine3: correct console uart pinmux Configuration was correct enough to work with the pre-configuration done by uboot. While at it, also document the location. Signed-off-by: Andreas Kemnade Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6sl-tolino-shine3.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts b/arch/arm/boot/dts/imx6sl-tolino-shine3.dts index 27143ea0f0f1..62d2ebda04ff 100644 --- a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts +++ b/arch/arm/boot/dts/imx6sl-tolino-shine3.dts @@ -156,7 +156,7 @@ pinctrl_uart1: uart1grp { fsl,pins = < MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1 - MX6SL_PAD_UART1_RXD__UART1_TX_DATA 0x1b0b1 + MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1 >; }; From 3ad6be94e7103c5a941dddaa10d9471528a64421 Mon Sep 17 00:00:00 2001 From: Andreas Kemnade Date: Wed, 13 Jan 2021 00:15:49 +0100 Subject: [PATCH 254/584] ARM: dts: imx: e60k02: add second uart There is another uart next to the console uart used by vendor uboot and kernel, enable it and document its location. Signed-off-by: Andreas Kemnade Signed-off-by: Shawn Guo --- arch/arm/boot/dts/e60k02.dtsi | 6 ++++++ arch/arm/boot/dts/imx6sl-tolino-shine3.dts | 13 ++++++++++++- arch/arm/boot/dts/imx6sll-kobo-clarahd.dts | 13 ++++++++++++- 3 files changed, 30 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/e60k02.dtsi b/arch/arm/boot/dts/e60k02.dtsi index 3af1ab4458ef..cfb239d5186a 100644 --- a/arch/arm/boot/dts/e60k02.dtsi +++ b/arch/arm/boot/dts/e60k02.dtsi @@ -278,6 +278,12 @@ }; &uart1 { + /* J4, through-hole */ + status = "okay"; +}; + +&uart4 { + /* TP198, next to J4, SMD pads */ status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts b/arch/arm/boot/dts/imx6sl-tolino-shine3.dts index 62d2ebda04ff..e3f1e8d79528 100644 --- a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts +++ b/arch/arm/boot/dts/imx6sl-tolino-shine3.dts @@ -94,7 +94,6 @@ MX6SL_PAD_KEY_ROW7__GPIO4_IO07 0x79 MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x79 MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x79 - MX6SL_PAD_KEY_ROW6__GPIO4_IO05 0x79 >; }; @@ -160,6 +159,13 @@ >; }; + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1 + MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1 + >; + }; + pinctrl_usbotg1: usbotg1grp { fsl,pins = < MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059 @@ -300,6 +306,11 @@ pinctrl-0 = <&pinctrl_uart1>; }; +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; +}; + &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; pinctrl-0 = <&pinctrl_usdhc2>; diff --git a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts b/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts index 7214d1c98249..90b32f5eb529 100644 --- a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts +++ b/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts @@ -104,7 +104,6 @@ MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 0x79 MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x79 MX6SLL_PAD_KEY_COL5__GPIO4_IO02 0x79 - MX6SLL_PAD_KEY_ROW6__GPIO4_IO05 0x79 >; }; @@ -170,6 +169,13 @@ >; }; + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6SLL_PAD_KEY_ROW6__UART4_DCE_TX 0x1b0b1 + MX6SLL_PAD_KEY_COL6__UART4_DCE_RX 0x1b0b1 + >; + }; + pinctrl_usbotg1: usbotg1grp { fsl,pins = < MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059 @@ -302,6 +308,11 @@ pinctrl-0 = <&pinctrl_uart1>; }; +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; +}; + &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep"; pinctrl-0 = <&pinctrl_usdhc2>; From 896dd923ad26b900590133c961f26d21a7f18ba7 Mon Sep 17 00:00:00 2001 From: Koji Matsuoka Date: Fri, 8 Jan 2021 11:43:45 +0100 Subject: [PATCH 255/584] arm64: dts: renesas: r8a779a0: Add MSIOF device nodes Add device nodes for the Clock-Synchronized Serial Interface with FIFO (MSIOF) instances on the Renesas R-Car V3U (r8a779a0) SoC. Signed-off-by: Koji Matsuoka Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20210108104345.2026857-1-geert+renesas@glider.be --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 90 +++++++++++++++++++++++ 1 file changed, 90 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 3bc15592d000..25c722302de6 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -264,6 +264,96 @@ status = "disabled"; }; + msiof0: spi@e6e90000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6e90000 0 0x0064>; + interrupts = ; + clocks = <&cpg CPG_MOD 618>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 618>; + dmas = <&dmac1 0x41>, <&dmac1 0x40>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof1: spi@e6ea0000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6ea0000 0 0x0064>; + interrupts = ; + clocks = <&cpg CPG_MOD 619>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 619>; + dmas = <&dmac1 0x43>, <&dmac1 0x42>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof2: spi@e6c00000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c00000 0 0x0064>; + interrupts = ; + clocks = <&cpg CPG_MOD 620>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 620>; + dmas = <&dmac1 0x45>, <&dmac1 0x44>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof3: spi@e6c10000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c10000 0 0x0064>; + interrupts = ; + clocks = <&cpg CPG_MOD 621>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 621>; + dmas = <&dmac1 0x47>, <&dmac1 0x46>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof4: spi@e6c20000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c20000 0 0x0064>; + interrupts = ; + clocks = <&cpg CPG_MOD 622>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 622>; + dmas = <&dmac1 0x49>, <&dmac1 0x48>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + msiof5: spi@e6c28000 { + compatible = "renesas,msiof-r8a779a0", + "renesas,rcar-gen3-msiof"; + reg = <0 0xe6c28000 0 0x0064>; + interrupts = ; + clocks = <&cpg CPG_MOD 623>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 623>; + dmas = <&dmac1 0x4b>, <&dmac1 0x4a>; + dma-names = "tx", "rx"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + dmac1: dma-controller@e7350000 { compatible = "renesas,dmac-r8a779a0"; reg = <0 0xe7350000 0 0x1000>, From e0ab5bf98208294f7fb39d8ce3746eaf39d38dfe Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:20 +0100 Subject: [PATCH 256/584] dt-bindings: sunxi: Fix the pinecube compatible Commit 6ab48105aae7 ("ARM: dts: s3: pinecube: align compatible property to other S3 boards") changed the pinecube compatible to make it similar to the other S3 boards we have, but failed to update the bindings documentation. Fixes: 6ab48105aae7 ("ARM: dts: s3: pinecube: align compatible property to other S3 boards") Signed-off-by: Maxime Ripard Acked-by: Jernej Skrabec Acked-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210114113538.1233933-1-maxime@cerno.tech --- Documentation/devicetree/bindings/arm/sunxi.yaml | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 7ea4d9645e93..08607c7ec1bf 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -657,7 +657,8 @@ properties: - description: Pine64 PineCube items: - const: pine64,pinecube - - const: allwinner,sun8i-s3 + - const: sochip,s3 + - const: allwinner,sun8i-v3 - description: Pine64 PineH64 model A items: From dcd80eaf74ef781ee6e2585622d7b4956c47bb9a Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:21 +0100 Subject: [PATCH 257/584] dt-bindings: iio: adc: Add AXP803 compatible The AXP803 compatible was introduced recently with a fallback to the AXP813, but it was never documented. Cc: Jonathan Cameron Cc: Lars-Peter Clausen Cc: Peter Meerwald-Stadler Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Acked-by: Jonathan Cameron Link: https://lore.kernel.org/r/20210114113538.1233933-2-maxime@cerno.tech --- .../bindings/iio/adc/x-powers,axp209-adc.yaml | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) diff --git a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml index 5ccbb1f81960..e759a5da708d 100644 --- a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml @@ -46,10 +46,14 @@ description: | properties: compatible: - enum: - - x-powers,axp209-adc - - x-powers,axp221-adc - - x-powers,axp813-adc + oneOf: + - const: x-powers,axp209-adc + - const: x-powers,axp221-adc + - const: x-powers,axp813-adc + + - items: + - const: x-powers,axp803-adc + - const: x-powers,axp813-adc "#io-channel-cells": const: 1 From 48b47749e334b3891f33b9425b470a3c92be8dae Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:22 +0100 Subject: [PATCH 258/584] dt-bindings: rtc: sun6i-a31-rtc: Loosen the requirements on the clocks The commit ec98a87509f4 ("rtc: sun6i: Make external 32k oscillator optional") loosened the requirement of the clocks property, making it optional. However, the binding still required it to be present. Cc: Alexandre Belloni Fixes: ec98a87509f4 ("rtc: sun6i: Make external 32k oscillator optional") Signed-off-by: Maxime Ripard Acked-by: Jernej Skrabec Acked-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210114113538.1233933-3-maxime@cerno.tech --- .../devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 1 - 1 file changed, 1 deletion(-) diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml index 37c2a601c3fa..b1b0ee769b71 100644 --- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml +++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml @@ -128,7 +128,6 @@ required: - compatible - reg - interrupts - - clocks - clock-output-names additionalProperties: false From e299e6dd357474dd5b8c61e4ca447fa0abd86e4d Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:25 +0100 Subject: [PATCH 259/584] ARM: dts: sunxi: Fix the LED node names According to the LED bindings, the LED node names are supposed to be led plus an optional suffix. Let's fix our users to use that new scheme. Signed-off-by: Maxime Ripard Acked-by: Jernej Skrabec Acked-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210114113538.1233933-6-maxime@cerno.tech --- arch/arm/boot/dts/sun4i-a10-a1000.dts | 4 ++-- arch/arm/boot/dts/sun4i-a10-cubieboard.dts | 4 ++-- arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts | 2 +- arch/arm/boot/dts/sun4i-a10-marsboard.dts | 8 ++++---- arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts | 2 +- arch/arm/boot/dts/sun4i-a10-pcduino.dts | 4 ++-- arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts | 2 +- arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts | 2 +- arch/arm/boot/dts/sun5i-a10s-mk802.dts | 2 +- arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts | 2 +- arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts | 2 +- arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts | 2 +- arch/arm/boot/dts/sun5i-a13-licheepi-one.dts | 6 +++--- arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts | 2 +- arch/arm/boot/dts/sun5i-a13-olinuxino.dts | 2 +- arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts | 2 +- arch/arm/boot/dts/sun6i-a31-i7.dts | 2 +- arch/arm/boot/dts/sun6i-a31-m9.dts | 2 +- arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts | 2 +- arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 6 +++--- arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts | 4 ++-- arch/arm/boot/dts/sun7i-a20-bananapi.dts | 2 +- arch/arm/boot/dts/sun7i-a20-bananapro.dts | 4 ++-- arch/arm/boot/dts/sun7i-a20-cubieboard2.dts | 4 ++-- arch/arm/boot/dts/sun7i-a20-cubietruck.dts | 8 ++++---- arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts | 4 ++-- arch/arm/boot/dts/sun7i-a20-itead-ibox.dts | 4 ++-- arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts | 2 +- arch/arm/boot/dts/sun7i-a20-m3.dts | 2 +- arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts | 2 +- arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts | 6 +++--- arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts | 2 +- arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 2 +- arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts | 2 +- arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts | 4 ++-- arch/arm/boot/dts/sun7i-a20-orangepi.dts | 2 +- arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts | 6 ++---- arch/arm/boot/dts/sun7i-a20-pcduino3.dts | 4 ++-- arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts | 2 +- arch/arm/boot/dts/sun8i-a33-olinuxino.dts | 2 +- arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts | 4 ++-- arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts | 8 ++++---- arch/arm/boot/dts/sun8i-h3-beelink-x2.dts | 4 ++-- arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts | 4 ++-- arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts | 4 ++-- arch/arm/boot/dts/sun8i-h3-nanopi.dtsi | 4 ++-- arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts | 4 ++-- arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 6 +++--- arch/arm/boot/dts/sun8i-r16-parrot.dts | 8 ++++---- arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 4 ++-- arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts | 6 +++--- arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts | 2 +- arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi | 6 +++--- arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts | 4 ++-- .../boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts | 4 ++-- arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts | 4 ++-- arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 4 ++-- .../arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts | 4 ++-- .../boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts | 4 ++-- .../boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts | 4 ++-- arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts | 2 +- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts | 4 ++-- arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi | 4 ++-- arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts | 6 +++--- 64 files changed, 117 insertions(+), 119 deletions(-) diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts index af8ab736fd3c..20f9ed244851 100644 --- a/arch/arm/boot/dts/sun4i-a10-a1000.dts +++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts @@ -74,12 +74,12 @@ leds { compatible = "gpio-leds"; - red { + led-0 { label = "a1000:red:usr"; gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; }; - blue { + led-1 { label = "a1000:blue:pwr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts index 6ca02e824acc..0645d6064235 100644 --- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts @@ -75,12 +75,12 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_cubieboard>; - blue { + led-0 { label = "cubieboard:blue:usr"; gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* LED1 */ }; - green { + led-1 { label = "cubieboard:green:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* LED2 */ linux,default-trigger = "heartbeat"; diff --git a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts b/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts index 8a7b4c53d278..1aeb0bd5519e 100644 --- a/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts +++ b/arch/arm/boot/dts/sun4i-a10-jesurun-q5.dts @@ -63,7 +63,7 @@ leds { compatible = "gpio-leds"; - green { + led { label = "q5:green:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; /* PH20 */ }; diff --git a/arch/arm/boot/dts/sun4i-a10-marsboard.dts b/arch/arm/boot/dts/sun4i-a10-marsboard.dts index a843e57530ed..81fdb217d339 100644 --- a/arch/arm/boot/dts/sun4i-a10-marsboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-marsboard.dts @@ -62,22 +62,22 @@ leds { compatible = "gpio-leds"; - red1 { + led-0 { label = "marsboard:red1:usr"; gpios = <&pio 1 5 GPIO_ACTIVE_HIGH>; }; - red2 { + led-1 { label = "marsboard:red2:usr"; gpios = <&pio 1 6 GPIO_ACTIVE_HIGH>; }; - red3 { + led-2 { label = "marsboard:red3:usr"; gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; }; - red4 { + led-3 { label = "marsboard:red4:usr"; gpios = <&pio 1 8 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts index 845f76824d57..ad0e25af45be 100644 --- a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts @@ -74,7 +74,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxinolime>; - green { + led { label = "a10-olinuxino-lime:green:usr"; gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/sun4i-a10-pcduino.dts index 83287b6c975e..1ac82376baef 100644 --- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts +++ b/arch/arm/boot/dts/sun4i-a10-pcduino.dts @@ -63,12 +63,12 @@ leds { compatible = "gpio-leds"; - tx { + led-0 { label = "pcduino:green:tx"; gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; }; - rx { + led-1 { label = "pcduino:green:rx"; gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts index 64d50fcfcd3a..04b0e6d28769 100644 --- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts +++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t003.dts @@ -62,7 +62,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_t003>; - red { + led { label = "t003-tv-dongle:red:usr"; gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ default-state = "on"; diff --git a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts index 8af0eae2ddc1..667bc2dc1ea9 100644 --- a/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts +++ b/arch/arm/boot/dts/sun5i-a10s-auxtek-t004.dts @@ -62,7 +62,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_t004>; - red { + led { label = "t004-tv-dongle:red:usr"; gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ default-state = "on"; diff --git a/arch/arm/boot/dts/sun5i-a10s-mk802.dts b/arch/arm/boot/dts/sun5i-a10s-mk802.dts index 6e90ccb267aa..d0219404c231 100644 --- a/arch/arm/boot/dts/sun5i-a10s-mk802.dts +++ b/arch/arm/boot/dts/sun5i-a10s-mk802.dts @@ -60,7 +60,7 @@ leds { compatible = "gpio-leds"; - red { + led { label = "mk802:red:usr"; gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; /* PB2 */ }; diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts index d6bb82c295f0..5832bb31fc51 100644 --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts @@ -79,7 +79,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxino>; - green { + led { label = "a10s-olinuxino-micro:green:usr"; gpios = <&pio 4 3 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts b/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts index b2a49a216ebf..964360f0610a 100644 --- a/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts +++ b/arch/arm/boot/dts/sun5i-a10s-r7-tv-dongle.dts @@ -63,7 +63,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_r7>; - green { + led { label = "r7-tv-dongle:green:usr"; gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts b/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts index 1f74ba1634cc..ef8baa992687 100644 --- a/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts +++ b/arch/arm/boot/dts/sun5i-a10s-wobo-i5.dts @@ -62,7 +62,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "a10s-wobo-i5:blue:usr"; gpios = <&pio 1 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts b/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts index ba8d75b3c716..2ce361f8fede 100644 --- a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts +++ b/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts @@ -66,18 +66,18 @@ leds { compatible = "gpio-leds"; - red { + led-0 { label ="licheepi:red:usr"; gpios = <&pio 2 5 GPIO_ACTIVE_LOW>; }; - green { + led-1 { label ="licheepi:green:usr"; gpios = <&pio 2 19 GPIO_ACTIVE_LOW>; default-state = "on"; }; - blue { + led-2 { label ="licheepi:blue:usr"; gpios = <&pio 2 4 GPIO_ACTIVE_LOW>; }; diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts index 5df398d77238..bfe1075e62cc 100644 --- a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts @@ -64,7 +64,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxinom>; - power { + led { label = "a13-olinuxino-micro:green:power"; gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts index 39101228a755..fadeae3cd8bb 100644 --- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts +++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts @@ -66,7 +66,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxino>; - power { + led { gpios = <&pio 6 9 GPIO_ACTIVE_HIGH>; default-state = "on"; }; diff --git a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts b/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts index e9ef97c9c893..3428bebceff0 100644 --- a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts +++ b/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts @@ -37,7 +37,7 @@ leds { compatible = "gpio-leds"; - power { + led { gpios = <&pio 4 8 GPIO_ACTIVE_LOW>; /* PE8 */ default-state = "on"; }; diff --git a/arch/arm/boot/dts/sun6i-a31-i7.dts b/arch/arm/boot/dts/sun6i-a31-i7.dts index 6cc8ccf53d88..744723d956f0 100644 --- a/arch/arm/boot/dts/sun6i-a31-i7.dts +++ b/arch/arm/boot/dts/sun6i-a31-i7.dts @@ -72,7 +72,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "i7:blue:usr"; gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/sun6i-a31-m9.dts index a645c8f4257c..aff716b523c4 100644 --- a/arch/arm/boot/dts/sun6i-a31-m9.dts +++ b/arch/arm/boot/dts/sun6i-a31-m9.dts @@ -61,7 +61,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "m9:blue:pwr"; gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts index 648f24746234..959ed9ce4b48 100644 --- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts +++ b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts @@ -61,7 +61,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "a1000g:blue:pwr"; gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts index 367006fb280d..b4ce60a3b194 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts @@ -59,17 +59,17 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "bpi-m2:blue:usr"; gpios = <&pio 6 11 GPIO_ACTIVE_HIGH>; /* PG11 */ }; - green { + led-1 { label = "bpi-m2:green:usr"; gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */ }; - red { + led-2 { label = "bpi-m2:red:usr"; gpios = <&pio 6 5 GPIO_ACTIVE_HIGH>; /* PG5 */ }; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts index 8945dbb114a2..caa935ca4f19 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts @@ -74,12 +74,12 @@ leds { compatible = "gpio-leds"; - green { + led-0 { label = "bananapi-m1-plus:green:usr"; gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; }; - pwr { + led-1 { label = "bananapi-m1-plus:pwr:usr"; gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi.dts b/arch/arm/boot/dts/sun7i-a20-bananapi.dts index 0b3d9ae75650..9d792d7a0f92 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapi.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapi.dts @@ -77,7 +77,7 @@ leds { compatible = "gpio-leds"; - green { + led { label = "bananapi:green:usr"; gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-bananapro.dts b/arch/arm/boot/dts/sun7i-a20-bananapro.dts index 01ccff756996..042badd50b42 100644 --- a/arch/arm/boot/dts/sun7i-a20-bananapro.dts +++ b/arch/arm/boot/dts/sun7i-a20-bananapro.dts @@ -63,12 +63,12 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "bananapro:blue:usr"; gpios = <&pio 6 2 GPIO_ACTIVE_HIGH>; }; - green { + led-1 { label = "bananapro:green:usr"; gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts index b8203e4ef21c..e35e6990c4b2 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts @@ -75,12 +75,12 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "cubieboard2:blue:usr"; gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; }; - green { + led-1 { label = "cubieboard2:green:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts index 9109ca0919ad..52160e368304 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts @@ -75,22 +75,22 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "cubietruck:blue:usr"; gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; }; - orange { + led-1 { label = "cubietruck:orange:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; }; - white { + led-2 { label = "cubietruck:white:usr"; gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; }; - green { + led-3 { label = "cubietruck:green:usr"; gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts index 358ed5f1b1c1..b21ddd0ec1c2 100644 --- a/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts +++ b/arch/arm/boot/dts/sun7i-a20-i12-tvbox.dts @@ -62,12 +62,12 @@ leds { compatible = "gpio-leds"; - red { + led-0 { label = "i12_tvbox:red:usr"; gpios = <&pio 7 9 GPIO_ACTIVE_LOW>; }; - blue { + led-1 { label = "i12_tvbox:blue:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts index 946c27278321..8ff83016ff5a 100644 --- a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts +++ b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts @@ -53,13 +53,13 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_itead_core>; - green { + led-0 { label = "itead_core:green:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - blue { + led-1 { label = "itead_core:blue:usr"; gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts b/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts index 17fa8901fc00..97518afe4658 100644 --- a/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts +++ b/arch/arm/boot/dts/sun7i-a20-lamobo-r1.dts @@ -75,7 +75,7 @@ leds { compatible = "gpio-leds"; - green { + led { label = "lamobo_r1:green:usr"; gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-m3.dts b/arch/arm/boot/dts/sun7i-a20-m3.dts index 6bff9e731fc3..f161d5238860 100644 --- a/arch/arm/boot/dts/sun7i-a20-m3.dts +++ b/arch/arm/boot/dts/sun7i-a20-m3.dts @@ -64,7 +64,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "m3:blue:usr"; gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts index 6f9c54b8e49a..f05ee32bc9cb 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som-evb.dts @@ -75,7 +75,7 @@ leds { compatible = "gpio-leds"; - green { + led { label = "a20-olimex-som-evb:green:usr"; gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts b/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts index 230d62a6b8f1..54af6c18075b 100644 --- a/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts +++ b/arch/arm/boot/dts/sun7i-a20-olimex-som204-evb.dts @@ -46,19 +46,19 @@ leds { compatible = "gpio-leds"; - stat { + led-0 { label = "a20-som204-evb:green:stat"; gpios = <&pio 8 0 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - led1 { + led-1 { label = "a20-som204-evb:green:led1"; gpios = <&pio 8 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - led2 { + led-2 { label = "a20-som204-evb:yellow:led2"; gpios = <&pio 8 11 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts index 2adbac860119..92938d022295 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime.dts @@ -78,7 +78,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxinolime>; - green { + led { label = "a20-olinuxino-lime:green:usr"; gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts index 9ba62774e89a..8077f1716fbc 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts @@ -75,7 +75,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxinolime>; - green { + led { label = "a20-olinuxino-lime2:green:usr"; gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts index 359bd0d5b3b1..a1b89b2a2999 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts @@ -82,7 +82,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pins_olinuxino>; - green { + led { label = "a20-olinuxino-micro:green:usr"; gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts index 2e328d2cefc1..84efa01e7cba 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi-mini.dts @@ -75,12 +75,12 @@ leds { compatible = "gpio-leds"; - green { + led-0 { label = "orangepi:green:usr"; gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */ }; - blue { + led-1 { label = "orangepi:blue:usr"; gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */ }; diff --git a/arch/arm/boot/dts/sun7i-a20-orangepi.dts b/arch/arm/boot/dts/sun7i-a20-orangepi.dts index d75b2e2bab28..5d77f1d9818f 100644 --- a/arch/arm/boot/dts/sun7i-a20-orangepi.dts +++ b/arch/arm/boot/dts/sun7i-a20-orangepi.dts @@ -64,7 +64,7 @@ leds { compatible = "gpio-leds"; - green { + led { label = "orangepi:green:usr"; gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>; /* PH24 */ }; diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts index bf38c66c1815..e40ecb48d726 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3-nano.dts @@ -72,14 +72,12 @@ leds { compatible = "gpio-leds"; - /* Marked "LED3" on the PCB. */ - usr1 { + led-3 { label = "pcduino3-nano:green:usr1"; gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; /* PH16 */ }; - /* Marked "LED4" on the PCB. */ - usr2 { + led-4 { label = "pcduino3-nano:green:usr2"; gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; /* PH15 */ }; diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts index cc8271d777b8..4f8d55d3ba79 100644 --- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts +++ b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts @@ -64,12 +64,12 @@ leds { compatible = "gpio-leds"; - tx { + led-0 { label = "pcduino3:green:tx"; gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; }; - rx { + led-1 { label = "pcduino3:green:rx"; gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; }; diff --git a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts b/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts index 317763069c0a..065cb620aa99 100644 --- a/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts +++ b/arch/arm/boot/dts/sun8i-a33-inet-d978-rev2.dts @@ -63,7 +63,7 @@ pinctrl-names = "default"; pinctrl-0 = <&led_pin_d978>; - home { + led { label = "d978:blue:home"; gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */ }; diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts index a1953b2872d0..9adf58f866d6 100644 --- a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts +++ b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts @@ -62,7 +62,7 @@ leds { compatible = "gpio-leds"; - green { + led { label = "a33-olinuxino:green:usr"; gpios = <&pio 1 7 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts index 431f70234d36..b60016a4429c 100644 --- a/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts +++ b/arch/arm/boot/dts/sun8i-a83t-bananapi-m3.dts @@ -74,12 +74,12 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "bananapi-m3:blue:usr"; gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; }; - green { + led-1 { label = "bananapi-m3:green:usr"; gpios = <&axp_gpio 0 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts index d8326a5c681d..e26af7cf10e0 100644 --- a/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts +++ b/arch/arm/boot/dts/sun8i-a83t-cubietruck-plus.dts @@ -74,22 +74,22 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "cubietruck-plus:blue:usr"; gpios = <&pio 3 25 GPIO_ACTIVE_HIGH>; /* PD25 */ }; - orange { + led-1 { label = "cubietruck-plus:orange:usr"; gpios = <&pio 3 26 GPIO_ACTIVE_HIGH>; /* PD26 */ }; - white { + led-2 { label = "cubietruck-plus:white:usr"; gpios = <&pio 3 27 GPIO_ACTIVE_HIGH>; /* PD27 */ }; - green { + led-3 { label = "cubietruck-plus:green:usr"; gpios = <&pio 4 4 GPIO_ACTIVE_HIGH>; /* PE4 */ }; diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts index 45a24441ff18..62b5280ec093 100644 --- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts +++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts @@ -75,13 +75,13 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "beelink-x2:blue:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ default-state = "on"; }; - red { + led-1 { label = "beelink-x2:red:standby"; gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ }; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts index 6b149271ef13..8e7dfcffe1fb 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts @@ -25,13 +25,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "nanopi:red:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ default-state = "on"; }; - status { + led-1 { label = "nanopi:green:status"; gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ }; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts index 07867a0d569b..be49eabbff94 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts @@ -61,13 +61,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "nanopi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */ default-state = "on"; }; - status { + led-1 { label = "nanopi:blue:status"; gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ }; diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi index 4df29a65316d..c7c3e7d8b3c8 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi +++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi @@ -60,13 +60,13 @@ leds { compatible = "gpio-leds"; - status { + led-0 { label = "nanopi:blue:status"; gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; - pwr { + led-1 { label = "nanopi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts index 251bbab7d707..561ea1d2f861 100644 --- a/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-zero-plus2.dts @@ -73,13 +73,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts index e1c75f7fa3ca..015ba66fd277 100644 --- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts +++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts @@ -64,17 +64,17 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { label = "bpi-m2m:blue:usr"; gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; }; - green { + led-1 { label = "bpi-m2m:green:usr"; gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; }; - red { + led-2 { label = "bpi-m2m:red:power"; gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; default-state = "on"; diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/sun8i-r16-parrot.dts index 4f48eec6b2ef..09a6a3b2cccc 100644 --- a/arch/arm/boot/dts/sun8i-r16-parrot.dts +++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts @@ -64,14 +64,14 @@ leds { compatible = "gpio-leds"; - led1 { + led-1 { label = "parrot:led1:usr"; - gpio = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */ + gpios = <&pio 4 17 GPIO_ACTIVE_HIGH>; /* PE17 */ }; - led2 { + led-2 { label = "parrot:led2:usr"; - gpio = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */ + gpios = <&pio 4 16 GPIO_ACTIVE_HIGH>; /* PE16 */ }; }; diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts index 484b93df20cb..1fe251ea94bc 100644 --- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts +++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts @@ -63,12 +63,12 @@ leds { compatible = "gpio-leds"; - green { + led-0 { label = "cubieboard4:green:usr"; gpios = <&pio 7 17 GPIO_ACTIVE_HIGH>; /* PH17 */ }; - red { + led-1 { label = "cubieboard4:red:usr"; gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts index e5e840b9fbb4..f7fe9fa50cb3 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts @@ -36,18 +36,18 @@ leds { compatible = "gpio-leds"; - pwr-led { + led-0 { label = "bananapi-m64:red:pwr"; gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ default-state = "on"; }; - green { + led-1 { label = "bananapi-m64:green:user"; gpios = <&pio 4 14 GPIO_ACTIVE_HIGH>; /* PE14 */ }; - blue { + led-2 { label = "bananapi-m64:blue:user"; gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts index e58db8a6cab6..09b3c7fb82c0 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts @@ -35,7 +35,7 @@ leds { compatible = "gpio-leds"; - blue { + led { label = "nanopi-a64:blue:status"; gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index 7f37f9fea0ab..bcf64998a829 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -31,19 +31,19 @@ leds { compatible = "gpio-leds"; - blue { + led-0 { function = LED_FUNCTION_INDICATOR; color = ; gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */ }; - green { + led-1 { function = LED_FUNCTION_INDICATOR; color = ; gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */ }; - red { + led-2 { function = LED_FUNCTION_INDICATOR; color = ; gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */ diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts index a1864a89fb89..f0a16f355e27 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts @@ -52,12 +52,12 @@ leds { compatible = "gpio-leds"; - capslock { + led-0 { label = "teres-i:green:capslock"; gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */ }; - numlock { + led-1 { label = "teres-i:green:numlock"; gpios = <&pio 2 4 GPIO_ACTIVE_HIGH>; /* PC4 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts index 9d93fe153689..4c3921ac236c 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo-plus2.dts @@ -25,13 +25,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "nanopi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "nanopi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts index b059e20813bd..02f8e72f0cad 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-neo2.dts @@ -22,13 +22,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "nanopi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "nanopi:blue:status"; gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts index 8bf2db9dcbda..1010c1b22d2e 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts @@ -42,13 +42,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts index 33ab44072e6d..74e0444af19b 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts @@ -36,13 +36,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts index ef5ca6444220..d13980ed7a79 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts @@ -33,13 +33,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts index de19e68eb84e..22530ace12d5 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus2.dts @@ -33,13 +33,13 @@ leds { compatible = "gpio-leds"; - pwr { + led-0 { label = "orangepi:green:pwr"; gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; default-state = "on"; }; - status { + led-1 { label = "orangepi:red:status"; gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts index 7c9dbde645b5..4f4755152fce 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts @@ -43,7 +43,7 @@ leds { compatible = "gpio-leds"; - power { + led { label = "beelink:white:power"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ default-state = "on"; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts index 15c9dd8c4479..7e83f6146f8a 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts @@ -43,13 +43,13 @@ leds { compatible = "gpio-leds"; - power { + led-0 { label = "orangepi:red:power"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ default-state = "on"; }; - status { + led-1 { label = "orangepi:green:status"; gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi index ebc120a9232f..da0875bd38d4 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi.dtsi @@ -42,13 +42,13 @@ leds { compatible = "gpio-leds"; - power { + led-0 { label = "orangepi:red:power"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ default-state = "on"; }; - status { + led-1 { label = "orangepi:green:status"; gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ }; diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts index 15ceba027a73..b868ad17af8f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64.dts @@ -44,17 +44,17 @@ leds { compatible = "gpio-leds"; - heartbeat { + led-0 { label = "pine-h64:green:heartbeat"; gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ }; - link { + led-1 { label = "pine-h64:white:link"; gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>; /* PL3 */ }; - status { + led-2 { label = "pine-h64:blue:status"; gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ }; From 86131fb96ef6e3cda0d5a5def5b5d675705de716 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:26 +0100 Subject: [PATCH 260/584] ARM: dts: sunxi: Add missing backlight supply The pwm-backlight binding requires a power supply. Make sure we provide one. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-7-maxime@cerno.tech --- arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts | 1 + arch/arm/boot/dts/sun4i-a10-inet1.dts | 1 + arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts | 1 + arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts | 1 + arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts | 1 + arch/arm/boot/dts/sun5i-gr8-evb.dts | 2 +- arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi | 1 + arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts | 1 + arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts | 2 +- arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi | 1 + arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi | 9 +++++++++ 11 files changed, 19 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts b/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts index 8ee3ff42bd55..63e77c05bfda 100644 --- a/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts +++ b/arch/arm/boot/dts/sun4i-a10-dserve-dsrv9703c.dts @@ -62,6 +62,7 @@ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + power-supply = <®_vcc3v3>; }; chosen { diff --git a/arch/arm/boot/dts/sun4i-a10-inet1.dts b/arch/arm/boot/dts/sun4i-a10-inet1.dts index ca878384e902..60e432a0ef1c 100644 --- a/arch/arm/boot/dts/sun4i-a10-inet1.dts +++ b/arch/arm/boot/dts/sun4i-a10-inet1.dts @@ -62,6 +62,7 @@ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + power-supply = <®_vcc3v3>; }; chosen { diff --git a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts index 24a3d23e1952..c32596947647 100644 --- a/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts +++ b/arch/arm/boot/dts/sun4i-a10-pov-protab2-ips9.dts @@ -62,6 +62,7 @@ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + power-supply = <®_vcc3v3>; }; chosen { diff --git a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts b/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts index a23bf24792ec..d059388d7252 100644 --- a/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts +++ b/arch/arm/boot/dts/sun5i-a13-empire-electronix-d709.dts @@ -61,6 +61,7 @@ pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; + power-supply = <®_vcc3v3>; /* TODO: backlight uses axp gpio1 as enable pin */ }; diff --git a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts b/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts index 3428bebceff0..d60407772e5d 100644 --- a/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts +++ b/arch/arm/boot/dts/sun5i-a13-pocketbook-touch-lux-3.dts @@ -28,6 +28,7 @@ enable-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; + power-supply = <®_vcc3v3>; }; chosen { diff --git a/arch/arm/boot/dts/sun5i-gr8-evb.dts b/arch/arm/boot/dts/sun5i-gr8-evb.dts index 4c20d731a9c6..f4fe258ef06d 100644 --- a/arch/arm/boot/dts/sun5i-gr8-evb.dts +++ b/arch/arm/boot/dts/sun5i-gr8-evb.dts @@ -71,7 +71,7 @@ compatible = "pwm-backlight"; pwms = <&pwm 0 10000 0>; enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; - + power-supply = <®_vcc3v3>; brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; }; diff --git a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi index 1a9926d71410..6847f66699ac 100644 --- a/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun5i-reference-design-tablet.dtsi @@ -55,6 +55,7 @@ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; enable-gpios = <&axp_gpio 1 GPIO_ACTIVE_HIGH>; /* AXP GPIO1 */ + power-supply = <®_vcc3v0>; }; chosen { diff --git a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts index 6a66b0432dfa..fef02fcbbdf8 100644 --- a/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts +++ b/arch/arm/boot/dts/sun7i-a20-wexler-tab7200.dts @@ -64,6 +64,7 @@ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ + power-supply = <®_vcc3v3>; }; chosen { diff --git a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts index bfc9bb277a49..83b01b03e08e 100644 --- a/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts +++ b/arch/arm/boot/dts/sun8i-a83t-tbs-a711.dts @@ -65,7 +65,7 @@ compatible = "pwm-backlight"; pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; enable-gpios = <&pio 3 29 GPIO_ACTIVE_HIGH>; - + power-supply = <®_sw>; brightness-levels = <0 1 2 4 8 16 32 64 128 255>; default-brightness-level = <9>; }; diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi index b3d8b8f056cd..daf4be6416df 100644 --- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi @@ -54,6 +54,7 @@ brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>; default-brightness-level = <8>; enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ + power-supply = <®_dc1sw>; }; chosen { diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index bcf64998a829..bbc26abb1e10 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -21,6 +21,7 @@ compatible = "pwm-backlight"; pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>; enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */ + power-supply = <®_ps>; /* Backlight configuration differs per PinePhone revision. */ }; @@ -50,6 +51,14 @@ }; }; + reg_ps: ps-regulator { + compatible = "regulator-fixed"; + regulator-name = "ps"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; + reg_vbat_wifi: vbat-wifi { compatible = "regulator-fixed"; regulator-min-microvolt = <3300000>; From 36a4e598388670b4f95b67420fc2b1b0a9d15b3d Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:27 +0100 Subject: [PATCH 261/584] ARM: dts: sunxi: Fix CPU thermal zone node name The CPU thermal zone is called on most of the older DTSI cpu_thermal. However, the underscore is an invalid character for a node name and the thermal zone binding explicitly requires that zones are called *-thermal. Let's fix it. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-8-maxime@cerno.tech --- arch/arm/boot/dts/sun5i-a13.dtsi | 2 +- arch/arm/boot/dts/sun6i-a31.dtsi | 2 +- arch/arm/boot/dts/sun7i-a20.dtsi | 2 +- arch/arm/boot/dts/sun8i-a33.dtsi | 2 +- 4 files changed, 4 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi index ae04955fd9a3..7075e10911d5 100644 --- a/arch/arm/boot/dts/sun5i-a13.dtsi +++ b/arch/arm/boot/dts/sun5i-a13.dtsi @@ -48,7 +48,7 @@ / { thermal-zones { - cpu_thermal { + cpu-thermal { /* milliseconds */ polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index f3425a66fc0a..92fd47c54d73 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -165,7 +165,7 @@ }; thermal-zones { - cpu_thermal { + cpu-thermal { /* milliseconds */ polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index 6d6a37940db2..5a40e0280665 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -140,7 +140,7 @@ }; thermal-zones { - cpu_thermal { + cpu-thermal { /* milliseconds */ polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm/boot/dts/sun8i-a33.dtsi b/arch/arm/boot/dts/sun8i-a33.dtsi index c458f5fb124f..7344c37107c6 100644 --- a/arch/arm/boot/dts/sun8i-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a33.dtsi @@ -288,7 +288,7 @@ }; thermal-zones { - cpu_thermal { + cpu-thermal { /* milliseconds */ polling-delay-passive = <250>; polling-delay = <1000>; From d36f964cc742d75e51a29a3ecfeded6993136235 Mon Sep 17 00:00:00 2001 From: Joakim Zhang Date: Sat, 16 Jan 2021 16:44:27 +0800 Subject: [PATCH 262/584] ARM: dts: imx6: add wakeup support via magic packet Add wakeup support via magic packet on i.MX platforms. Signed-off-by: Joakim Zhang Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-sabreauto.dtsi | 1 + arch/arm/boot/dts/imx6sx-sdb.dtsi | 2 ++ arch/arm/boot/dts/imx6ul.dtsi | 2 ++ 3 files changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index afe477f32984..5e58740d40c5 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -298,6 +298,7 @@ interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; fsl,err006687-workaround-present; + fsl,magic-packet; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi index 1351d7f70a54..c6e85e4a0883 100644 --- a/arch/arm/boot/dts/imx6sx-sdb.dtsi +++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi @@ -206,6 +206,7 @@ phy-mode = "rgmii-id"; phy-handle = <ðphy1>; phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>; + fsl,magic-packet; status = "okay"; mdio { @@ -227,6 +228,7 @@ pinctrl-0 = <&pinctrl_enet2>; phy-mode = "rgmii-id"; phy-handle = <ðphy2>; + fsl,magic-packet; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi index 9d3411cc597b..afeec01f6522 100644 --- a/arch/arm/boot/dts/imx6ul.dtsi +++ b/arch/arm/boot/dts/imx6ul.dtsi @@ -538,6 +538,7 @@ fsl,num-tx-queues = <1>; fsl,num-rx-queues = <1>; fsl,stop-mode = <&gpr 0x10 4>; + fsl,magic-packet; status = "disabled"; }; @@ -885,6 +886,7 @@ fsl,num-tx-queues = <1>; fsl,num-rx-queues = <1>; fsl,stop-mode = <&gpr 0x10 3>; + fsl,magic-packet; status = "disabled"; }; From 70eacf42a93aff6589a8b91279bbfe5f73c4ca3d Mon Sep 17 00:00:00 2001 From: Joakim Zhang Date: Sat, 16 Jan 2021 16:44:28 +0800 Subject: [PATCH 263/584] arm64: dts: imx8m: correct assigned clocks for FEC CLK_ENET_TIMER assigned clocks twice, should be a typo, correct to CLK_ENET_PHY_REF clock. Signed-off-by: Joakim Zhang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm.dtsi | 7 ++++--- arch/arm64/boot/dts/freescale/imx8mn.dtsi | 7 ++++--- arch/arm64/boot/dts/freescale/imx8mp.dtsi | 7 ++++--- 3 files changed, 12 insertions(+), 9 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index 9bee6f1889a4..5af0e63b1db1 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -915,11 +915,12 @@ assigned-clocks = <&clk IMX8MM_CLK_ENET_AXI>, <&clk IMX8MM_CLK_ENET_TIMER>, <&clk IMX8MM_CLK_ENET_REF>, - <&clk IMX8MM_CLK_ENET_TIMER>; + <&clk IMX8MM_CLK_ENET_PHY_REF>; assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_266M>, <&clk IMX8MM_SYS_PLL2_100M>, - <&clk IMX8MM_SYS_PLL2_125M>; - assigned-clock-rates = <0>, <0>, <125000000>, <100000000>; + <&clk IMX8MM_SYS_PLL2_125M>, + <&clk IMX8MM_SYS_PLL2_50M>; + assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; status = "disabled"; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index d021aba5fb1f..79c389969b83 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -913,11 +913,12 @@ assigned-clocks = <&clk IMX8MN_CLK_ENET_AXI>, <&clk IMX8MN_CLK_ENET_TIMER>, <&clk IMX8MN_CLK_ENET_REF>, - <&clk IMX8MN_CLK_ENET_TIMER>; + <&clk IMX8MN_CLK_ENET_PHY_REF>; assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_266M>, <&clk IMX8MN_SYS_PLL2_100M>, - <&clk IMX8MN_SYS_PLL2_125M>; - assigned-clock-rates = <0>, <0>, <125000000>, <100000000>; + <&clk IMX8MN_SYS_PLL2_125M>, + <&clk IMX8MN_SYS_PLL2_50M>; + assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; status = "disabled"; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index 9401e92f1c84..ba32725ff28c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -768,11 +768,12 @@ assigned-clocks = <&clk IMX8MP_CLK_ENET_AXI>, <&clk IMX8MP_CLK_ENET_TIMER>, <&clk IMX8MP_CLK_ENET_REF>, - <&clk IMX8MP_CLK_ENET_TIMER>; + <&clk IMX8MP_CLK_ENET_PHY_REF>; assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_266M>, <&clk IMX8MP_SYS_PLL2_100M>, - <&clk IMX8MP_SYS_PLL2_125M>; - assigned-clock-rates = <0>, <0>, <125000000>, <100000000>; + <&clk IMX8MP_SYS_PLL2_125M>, + <&clk IMX8MP_SYS_PLL2_50M>; + assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; status = "disabled"; From 6c17f2d6ab50691bfe67e65434568d759feb450b Mon Sep 17 00:00:00 2001 From: Joakim Zhang Date: Sat, 16 Jan 2021 16:44:29 +0800 Subject: [PATCH 264/584] arm64: dts: imx8mq: assign clock parents for FEC Assign clock parents for FEC, set "ptp" clock to 100M, "enet_clk_ref" to 125M. Signed-off-by: Joakim Zhang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 4ef8c92403dd..adcd6d5f6f5f 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -1172,6 +1172,15 @@ <&clk IMX8MQ_CLK_ENET_PHY_REF>; clock-names = "ipg", "ahb", "ptp", "enet_clk_ref", "enet_out"; + assigned-clocks = <&clk IMX8MQ_CLK_ENET_AXI>, + <&clk IMX8MQ_CLK_ENET_TIMER>, + <&clk IMX8MQ_CLK_ENET_REF>, + <&clk IMX8MQ_CLK_ENET_PHY_REF>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>, + <&clk IMX8MQ_SYS2_PLL_100M>, + <&clk IMX8MQ_SYS2_PLL_125M>, + <&clk IMX8MQ_SYS2_PLL_50M>; + assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; status = "disabled"; From 066438ae637b492f220c26cca304f1ce3d987a20 Mon Sep 17 00:00:00 2001 From: Joakim Zhang Date: Sat, 16 Jan 2021 16:44:30 +0800 Subject: [PATCH 265/584] arm64: dts: imx8m: add mac address for FEC Add mac address in efuse, so that FEC driver can parse it from nvmem cell. Signed-off-by: Joakim Zhang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm.dtsi | 7 +++++++ arch/arm64/boot/dts/freescale/imx8mn.dtsi | 7 +++++++ arch/arm64/boot/dts/freescale/imx8mp.dtsi | 7 +++++++ arch/arm64/boot/dts/freescale/imx8mq.dtsi | 7 +++++++ 4 files changed, 28 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index 5af0e63b1db1..acb8df609e2b 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -527,6 +527,10 @@ cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; + + fec_mac_address: mac-address@90 { + reg = <0x90 6>; + }; }; anatop: anatop@30360000 { @@ -923,6 +927,9 @@ assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; + nvmem-cells = <&fec_mac_address>; + nvmem-cell-names = "mac-address"; + nvmem_macaddr_swap; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index 79c389969b83..fae95114fd0a 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -540,6 +540,10 @@ cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; + + fec_mac_address: mac-address@90 { + reg = <0x90 6>; + }; }; anatop: anatop@30360000 { @@ -921,6 +925,9 @@ assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; + nvmem-cells = <&fec_mac_address>; + nvmem-cell-names = "mac-address"; + nvmem_macaddr_swap; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index ba32725ff28c..9dc63eddce16 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -337,6 +337,10 @@ cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; + + eth_mac1: mac-address@90 { + reg = <0x90 6>; + }; }; anatop: anatop@30360000 { @@ -776,6 +780,9 @@ assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; + nvmem-cells = <ð_mac1>; + nvmem-cell-names = "mac-address"; + nvmem_macaddr_swap; status = "disabled"; }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index adcd6d5f6f5f..a0ca7fc4b220 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -567,6 +567,10 @@ cpu_speed_grade: speed-grade@10 { reg = <0x10 4>; }; + + fec_mac_address: mac-address@90 { + reg = <0x90 6>; + }; }; anatop: syscon@30360000 { @@ -1183,6 +1187,9 @@ assigned-clock-rates = <0>, <100000000>, <125000000>, <0>; fsl,num-tx-queues = <3>; fsl,num-rx-queues = <3>; + nvmem-cells = <&fec_mac_address>; + nvmem-cell-names = "mac-address"; + nvmem_macaddr_swap; status = "disabled"; }; }; From afe993546334633daa3249b77540a30c0fb8997e Mon Sep 17 00:00:00 2001 From: Joakim Zhang Date: Sat, 16 Jan 2021 16:44:31 +0800 Subject: [PATCH 266/584] arm64: dts: imx8m: add fsl,stop-mode property for FEC Add fsl,stop-mode property for FEC to enable stop mode. Signed-off-by: Joakim Zhang Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mm.dtsi | 1 + arch/arm64/boot/dts/freescale/imx8mn.dtsi | 1 + arch/arm64/boot/dts/freescale/imx8mp.dtsi | 1 + arch/arm64/boot/dts/freescale/imx8mq.dtsi | 1 + 4 files changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi index acb8df609e2b..6bf1d15ba16a 100644 --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi @@ -930,6 +930,7 @@ nvmem-cells = <&fec_mac_address>; nvmem-cell-names = "mac-address"; nvmem_macaddr_swap; + fsl,stop-mode = <&gpr 0x10 3>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index fae95114fd0a..8004b7f36c77 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -928,6 +928,7 @@ nvmem-cells = <&fec_mac_address>; nvmem-cell-names = "mac-address"; nvmem_macaddr_swap; + fsl,stop-mode = <&gpr 0x10 3>; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi index 9dc63eddce16..47c8fe10a5ba 100644 --- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi @@ -782,6 +782,7 @@ fsl,num-rx-queues = <3>; nvmem-cells = <ð_mac1>; nvmem-cell-names = "mac-address"; + fsl,stop-mode = <&gpr 0x10 3>; nvmem_macaddr_swap; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index a0ca7fc4b220..963c97b4ba84 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -1190,6 +1190,7 @@ nvmem-cells = <&fec_mac_address>; nvmem-cell-names = "mac-address"; nvmem_macaddr_swap; + fsl,stop-mode = <&iomuxc_gpr 0x10 3>; status = "disabled"; }; }; From b840662bd55fb6dc9204585f071518123a87b59d Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 17 Jan 2021 16:09:51 +0100 Subject: [PATCH 267/584] ARM: dts: rockchip: rename thermal subnodes for rk3288 A test with the command below gives for example this error: /arch/arm/boot/dts/rk3288-tinker.dt.yaml: thermal-zones: 'cpu_thermal', 'gpu_thermal', 'reserve_thermal' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+' Rename Rockchip rk3288 thermal subnodes so that it ends with "-thermal" make ARCH=arm dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/ thermal/thermal-zones.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210117150953.16475-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3288.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 01ea1f170f77..29ffe2eb9bf9 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -488,14 +488,14 @@ }; thermal-zones { - reserve_thermal: reserve_thermal { + reserve_thermal: reserve-thermal { polling-delay-passive = <1000>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ thermal-sensors = <&tsadc 0>; }; - cpu_thermal: cpu_thermal { + cpu_thermal: cpu-thermal { polling-delay-passive = <100>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ @@ -539,7 +539,7 @@ }; }; - gpu_thermal: gpu_thermal { + gpu_thermal: gpu-thermal { polling-delay-passive = <100>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ From 7c96a5cf680ac7339999becd454e1f2fd9b258fb Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 17 Jan 2021 16:09:52 +0100 Subject: [PATCH 268/584] arm64: dts: rockchip: rename thermal subnodes for rk3368 A test with the command below gives for example this error: /arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dt.yaml: thermal-zones: 'cpu', 'gpu' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+' Make the rk3368 thermal subnode names in line with the rest of the Rockchip dts files. Add a label and rename them so that it ends with "-thermal" make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/ thermal/thermal-zones.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210117150953.16475-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3368.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index 3746f23dc3df..f6be54fdaa34 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -400,7 +400,7 @@ }; thermal-zones { - cpu { + cpu_thermal: cpu-thermal { polling-delay-passive = <100>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ @@ -444,7 +444,7 @@ }; }; - gpu { + gpu_thermal: gpu-thermal { polling-delay-passive = <100>; /* milliseconds */ polling-delay = <5000>; /* milliseconds */ From e58061b59787270a57839397e50bb4400b9e2de9 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 17 Jan 2021 16:09:53 +0100 Subject: [PATCH 269/584] arm64: dts: rockchip: rename thermal subnodes for rk3399 A test with the command below gives for example this error: /arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: thermal-zones: 'cpu', 'gpu' do not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', 'pinctrl-[0-9]+' Rename Rockchip rk3399 thermal subnodes so that it ends with "-thermal" make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/ thermal/thermal-zones.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210117150953.16475-3-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3399-rock960.dts | 2 +- arch/arm64/boot/dts/rockchip/rk3399.dtsi | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts index c88295782e7b..b207740819ef 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts @@ -126,7 +126,7 @@ }; &thermal_zones { - cpu_thermal: cpu { + cpu_thermal: cpu-thermal { polling-delay-passive = <100>; polling-delay = <1000>; thermal-sensors = <&tsadc 0>; diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index cd9fbd3cfcaf..4983dd18b4d8 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -764,7 +764,7 @@ }; thermal_zones: thermal-zones { - cpu_thermal: cpu { + cpu_thermal: cpu-thermal { polling-delay-passive = <100>; polling-delay = <1000>; @@ -808,7 +808,7 @@ }; }; - gpu_thermal: gpu { + gpu_thermal: gpu-thermal { polling-delay-passive = <100>; polling-delay = <1000>; From c6433083f5930fdf52ad47c8c0459719c810dc89 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sun, 17 Jan 2021 18:07:08 +0800 Subject: [PATCH 270/584] arm64: dts: rockchip: rk3328: Add clock_in_out property to gmac2phy node The gmac2phy is integrated with the PHY within the SoC. Any properties related to this integration can be included in the .dtsi file, instead of having board dts files specify them separately. Add the clock_in_out property to specify the direction of the PHY clock. This is the minimum required to have gmac2phy working on Linux. Other examples include assigned-clocks, assigned-clock-rates, and assigned-clock-parents properties, but the hardware default plus the implementation requesting the appropriate clock rate also works. Fixes: 9c4cc910fe28 ("ARM64: dts: rockchip: Add gmac2phy node support for rk3328") Signed-off-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210117100710.4857-2-wens@kernel.org Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3328.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi index 56b5ee7e54c4..17709faf651b 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi @@ -931,6 +931,7 @@ phy-mode = "rmii"; phy-handle = <&phy>; snps,txpbl = <0x4>; + clock_in_out = "output"; status = "disabled"; mdio { From 31b8e8592f6663c0937d1408f1fd6ed566fbde5c Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sun, 17 Jan 2021 18:07:09 +0800 Subject: [PATCH 271/584] dt-bindings: arm: rockchip: Add Radxa ROCK Pi E Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC. As the official wiki page puts it, "E for Ethernets". It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both directly served by Ethernet controllers in the SoC, a USB 3.0 host port, a power-only USB type-C port, a 3.5mm headphone jack for audio output, two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT and PoE header. The board comes in multiple configurations, differing in the amount of onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac 2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants can all share the same device tree. The USB 2.0 OTG controller is available on the 40-pin header. This is not enabled in the device tree, since it is possible to use it in a host-only configuration, or in OTG mode with an extra pin from the header as the ID pin. The device tree is based on the one of the Rock64, with various parts modified to match the ROCK Pi E, and some parts updated to newer styles, such as the gmac2io node's mdio sub-node. Add a compatible string for the new board. Acked-by: Rob Herring Signed-off-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210117100710.4857-3-wens@kernel.org Signed-off-by: Heiko Stuebner --- Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml index ef4544ad6f82..8a2dd9f1cff2 100644 --- a/Documentation/devicetree/bindings/arm/rockchip.yaml +++ b/Documentation/devicetree/bindings/arm/rockchip.yaml @@ -467,6 +467,11 @@ properties: - const: radxa,rockpi4 - const: rockchip,rk3399 + - description: Radxa ROCK Pi E + items: + - const: radxa,rockpi-e + - const: rockchip,rk3328 + - description: Radxa ROCK Pi N8 items: - const: radxa,rockpi-n8 From b918e81f2145967f0cadfe9ede38c69c1796fe09 Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Sun, 17 Jan 2021 18:07:10 +0800 Subject: [PATCH 272/584] arm64: dts: rockchip: rk3328: Add Radxa ROCK Pi E Radxa ROCK Pi E is a router oriented SBC based on Rockchip's RK3328 SoC. As the official wiki page puts it, "E for Ethernets". It features the RK3328 SoC, gigabit and fast Ethernet RJ45 ports, both directly served by Ethernet controllers in the SoC, a USB 3.0 host port, a power-only USB type-C port, a 3.5mm headphone jack for audio output, two LEDs, a 40-pin Raspberry Pi style GPIO header, and optional WiFi+BT and PoE header. The board comes in multiple configurations, differing in the amount of onboard RAM, the level of WiFi+BT (none, 802.11n 2.4GHz, or 802.11ac 2.4 GHz & 5 GHz), and whether PoE is supported or not. These variants can all share the same device tree. The USB 2.0 OTG controller is available on the 40-pin header. This is not enabled in the device tree, since it is possible to use it in a host-only configuration, or in OTG mode with an extra pin from the header as the ID pin. The device tree is based on the one of the Rock64, with various parts modified to match the ROCK Pi E, and some parts updated to newer styles, such as the gmac2io node's mdio sub-node. Add a new device tree file for the new board. The voltages for the adc-keys were selected to have some tolerances for resistor variances and the ADC itself also causing voltage drops. Since the recover button is the only button on the adc line, this should not cause any issues. Signed-off-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210117100710.4857-4-wens@kernel.org Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3328-rock-pi-e.dts | 382 ++++++++++++++++++ 2 files changed, 383 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile index 1ab55a124a87..b29a445b355a 100644 --- a/arch/arm64/boot/dts/rockchip/Makefile +++ b/arch/arm64/boot/dts/rockchip/Makefile @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb diff --git a/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts new file mode 100644 index 000000000000..2d71ca7e429c --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3328-rock-pi-e.dts @@ -0,0 +1,382 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * (C) Copyright 2020 Chen-Yu Tsai + * + * Based on ./rk3328-rock64.dts, which is + * + * Copyright (c) 2017 PINE64 + */ + +/dts-v1/; + +#include +#include +#include +#include + +#include "rk3328.dtsi" + +/ { + model = "Radxa ROCK Pi E"; + compatible = "radxa,rockpi-e", "rockchip,rk3328"; + + chosen { + stdout-path = "serial2:1500000n8"; + }; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 0>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1750000>; + + /* This button is unpopulated out of the factory. */ + button-recovery { + label = "Recovery"; + linux,code = ; + press-threshold-microvolt = <10000>; + }; + }; + + gmac_clkin: external-gmac-clock { + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_clkin"; + #clock-cells = <0>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pin>; + pinctrl-names = "default"; + + led-0 { + color = ; + gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + vcc_sd: sdmmc-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0m1_pin>; + regulator-name = "vcc_sd"; + regulator-boot-on; + vin-supply = <&vcc_io>; + }; + + vcc_host_5v: vcc-host-5v-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio3 RK_PA7 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb30_host_drv>; + enable-active-high; + regulator-name = "vcc_host_5v"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_sys>; + }; + + vcc_sys: vcc-sys { + compatible = "regulator-fixed"; + regulator-name = "vcc_sys"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + vcc_wifi: vcc-wifi-regulator { + compatible = "regulator-fixed"; + gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&wifi_en>; + regulator-name = "vcc_wifi"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vcc_io>; + }; +}; + +&analog_sound { + status = "okay"; +}; + +&codec { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vdd_arm>; +}; + +&cpu1 { + cpu-supply = <&vdd_arm>; +}; + +&cpu2 { + cpu-supply = <&vdd_arm>; +}; + +&cpu3 { + cpu-supply = <&vdd_arm>; +}; + +&emmc { + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + non-removable; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk>, <&emmc_cmd>, <&emmc_bus8>; + vmmc-supply = <&vcc_io>; + vqmmc-supply = <&vcc18_emmc>; + status = "okay"; +}; + +&gmac2io { + assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>; + assigned-clock-parents = <&gmac_clkin>, <&gmac_clkin>; + clock_in_out = "input"; + phy-handle = <&rtl8211e>; + phy-mode = "rgmii"; + phy-supply = <&vcc_io>; + pinctrl-names = "default"; + pinctrl-0 = <&rgmiim1_pins>; + snps,aal; + snps,rxpbl = <0x4>; + snps,txpbl = <0x4>; + tx_delay = <0x26>; + rx_delay = <0x11>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + rtl8211e: ethernet-phy@1 { + reg = <1>; + pinctrl-0 = <ð_phy_int_pin>, <ð_phy_reset_pin>; + pinctrl-names = "default"; + interrupt-parent = <&gpio1>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <50000>; + reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gmac2phy { + pinctrl-names = "default"; + pinctrl-0 = <&fephyled_linkm1>, <&fephyled_rxm1>; + status = "okay"; +}; + +&i2c1 { + status = "okay"; + + rk805: pmic@18 { + compatible = "rockchip,rk805"; + reg = <0x18>; + interrupt-parent = <&gpio2>; + interrupts = <6 IRQ_TYPE_LEVEL_LOW>; + #clock-cells = <1>; + clock-output-names = "xin32k", "rk805-clkout2"; + gpio-controller; + #gpio-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pmic_int_l>; + rockchip,system-power-controller; + wakeup-source; + + vcc1-supply = <&vcc_sys>; + vcc2-supply = <&vcc_sys>; + vcc3-supply = <&vcc_sys>; + vcc4-supply = <&vcc_sys>; + vcc5-supply = <&vcc_io>; + vcc6-supply = <&vcc_sys>; + + regulators { + vdd_log: DCDC_REG1 { + regulator-name = "vdd_log"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1450000>; + regulator-ramp-delay = <12500>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + + vdd_arm: DCDC_REG2 { + regulator-name = "vdd_arm"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <712500>; + regulator-max-microvolt = <1450000>; + regulator-ramp-delay = <12500>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <950000>; + }; + }; + + vcc_ddr: DCDC_REG3 { + regulator-name = "vcc_ddr"; + regulator-always-on; + regulator-boot-on; + + regulator-state-mem { + regulator-on-in-suspend; + }; + }; + + vcc_io: DCDC_REG4 { + regulator-name = "vcc_io"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <3300000>; + }; + }; + + vcc_18: LDO_REG1 { + regulator-name = "vcc_18"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vcc18_emmc: LDO_REG2 { + regulator-name = "vcc18_emmc"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1800000>; + }; + }; + + vdd_10: LDO_REG3 { + regulator-name = "vdd_10"; + regulator-always-on; + regulator-boot-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + + regulator-state-mem { + regulator-on-in-suspend; + regulator-suspend-microvolt = <1000000>; + }; + }; + }; + }; +}; + +&i2s1 { + status = "okay"; +}; + +&io_domains { + pmuio-supply = <&vcc_io>; + vccio1-supply = <&vcc_io>; + vccio2-supply = <&vcc18_emmc>; + vccio3-supply = <&vcc_io>; + vccio4-supply = <&vcc_io>; + vccio5-supply = <&vcc_io>; + vccio6-supply = <&vcc_io>; + status = "okay"; +}; + +&pinctrl { + ephy { + eth_phy_int_pin: eth-phy-int-pin { + rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_down>; + }; + + eth_phy_reset_pin: eth-phy-reset-pin { + rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; + }; + }; + + leds { + led_pin: led-pin { + rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + pmic { + pmic_int_l: pmic-int-l { + rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + + usb3 { + usb30_host_drv: usb30-host-drv { + rockchip,pins = <3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; + + wifi { + wifi_en: wifi-en { + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +}; + +&sdmmc { + bus-width = <4>; + cap-sd-highspeed; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>; + vmmc-supply = <&vcc_sd>; + status = "okay"; +}; + +&saradc { + vref-supply = <&vcc_18>; + status = "okay"; +}; + +&tsadc { + status = "okay"; +}; + +&u2phy { + status = "okay"; +}; + +&u2phy_host { + status = "okay"; +}; + +&uart2 { + status = "okay"; +}; + +&usb_host0_ehci { + status = "okay"; +}; From c56eeebc27af1c503589fa08bc46c0a3bcd6702a Mon Sep 17 00:00:00 2001 From: Yifeng Zhao Date: Thu, 10 Dec 2020 08:21:34 +0800 Subject: [PATCH 273/584] arm64: dts: rockchip: Add NFC node for RK3308 SoC Add NAND FLASH Controller(NFC) node for RK3308 SoC. Signed-off-by: Yifeng Zhao Link: https://lore.kernel.org/r/20201210002134.5686-5-yifeng.zhao@rock-chips.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3308.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi index 2560b98771ca..7211fab7a6e4 100644 --- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi @@ -629,6 +629,21 @@ status = "disabled"; }; + nfc: nand-controller@ff4b0000 { + compatible = "rockchip,rk3308-nfc", + "rockchip,rv1108-nfc"; + reg = <0x0 0xff4b0000 0x0 0x4000>; + interrupts = ; + clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>; + clock-names = "ahb", "nfc"; + assigned-clocks = <&cru SCLK_NANDC>; + assigned-clock-rates = <150000000>; + pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_csn0 + &flash_rdn &flash_rdy &flash_wrn>; + pinctrl-names = "default"; + status = "disabled"; + }; + cru: clock-controller@ff500000 { compatible = "rockchip,rk3308-cru"; reg = <0x0 0xff500000 0x0 0x1000>; From d00e6e22e8b9f8d3b8308706f57ae82119289792 Mon Sep 17 00:00:00 2001 From: Yifeng Zhao Date: Thu, 10 Dec 2020 08:22:16 +0800 Subject: [PATCH 274/584] arm64: dts: rockchip: Add NFC node for PX30 SoC Add NAND FLASH Controller(NFC) node for PX30 SoC. Signed-off-by: Yifeng Zhao Link: https://lore.kernel.org/r/20201210002219.5739-1-yifeng.zhao@rock-chips.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/px30.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi index af6bcef9e848..6a3e57761b25 100644 --- a/arch/arm64/boot/dts/rockchip/px30.dtsi +++ b/arch/arm64/boot/dts/rockchip/px30.dtsi @@ -973,6 +973,21 @@ status = "disabled"; }; + nfc: nand-controller@ff3b0000 { + compatible = "rockchip,px30-nfc"; + reg = <0x0 0xff3b0000 0x0 0x4000>; + interrupts = ; + clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>; + clock-names = "ahb", "nfc"; + assigned-clocks = <&cru SCLK_NANDC>; + assigned-clock-rates = <150000000>; + pinctrl-names = "default"; + pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_cs0 + &flash_rdn &flash_rdy &flash_wrn &flash_dqs>; + power-domains = <&power PX30_PD_MMC_NAND>; + status = "disabled"; + }; + gpu: gpu@ff400000 { compatible = "rockchip,px30-mali", "arm,mali-bifrost"; reg = <0x0 0xff400000 0x0 0x4000>; From 2525f194f9dc07c48b0a12697128357068c2e04b Mon Sep 17 00:00:00 2001 From: Yifeng Zhao Date: Thu, 10 Dec 2020 08:22:17 +0800 Subject: [PATCH 275/584] ARM: dts: rockchip: Add NFC node for RV1108 SoC Add NAND FLASH Controller(NFC) node for RV1108 SoC. Signed-off-by: Yifeng Zhao Link: https://lore.kernel.org/r/20201210002219.5739-2-yifeng.zhao@rock-chips.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rv1108.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+) diff --git a/arch/arm/boot/dts/rv1108.dtsi b/arch/arm/boot/dts/rv1108.dtsi index e491964b1c3d..15fa25585ea4 100644 --- a/arch/arm/boot/dts/rv1108.dtsi +++ b/arch/arm/boot/dts/rv1108.dtsi @@ -452,6 +452,17 @@ #reset-cells = <1>; }; + nfc: nand-controller@30100000 { + compatible = "rockchip,rv1108-nfc"; + reg = <0x30100000 0x1000>; + interrupts = ; + clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>; + clock-names = "ahb", "nfc"; + assigned-clocks = <&cru SCLK_NANDC>; + assigned-clock-rates = <150000000>; + status = "disabled"; + }; + emmc: mmc@30110000 { compatible = "rockchip,rv1108-dw-mshc", "rockchip,rk3288-dw-mshc"; reg = <0x30110000 0x4000>; From 9c2bfe53b2fc4a8a63311f162e80b27978db6c06 Mon Sep 17 00:00:00 2001 From: Yifeng Zhao Date: Thu, 10 Dec 2020 08:22:18 +0800 Subject: [PATCH 276/584] ARM: dts: rockchip: Add NFC node for RK2928 and other SoCs Add NAND FLASH Controller(NFC) node for RK2928, RK3066, RK3168 and RK3188 SoCs. Signed-off-by: Yifeng Zhao Link: https://lore.kernel.org/r/20201210002219.5739-3-yifeng.zhao@rock-chips.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3xxx.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rk3xxx.dtsi index 49bcdf46d03c..d3eb25844e97 100644 --- a/arch/arm/boot/dts/rk3xxx.dtsi +++ b/arch/arm/boot/dts/rk3xxx.dtsi @@ -276,6 +276,15 @@ status = "disabled"; }; + nfc: nand-controller@10500000 { + compatible = "rockchip,rk2928-nfc"; + reg = <0x10500000 0x4000>; + interrupts = ; + clocks = <&cru HCLK_NANDC0>; + clock-names = "ahb"; + status = "disabled"; + }; + pmu: pmu@20004000 { compatible = "rockchip,rk3066-pmu", "syscon", "simple-mfd"; reg = <0x20004000 0x100>; From 4cd9a03435bcd20ce6f524e3826fd263951c22fe Mon Sep 17 00:00:00 2001 From: Yifeng Zhao Date: Thu, 10 Dec 2020 08:22:19 +0800 Subject: [PATCH 277/584] ARM: dts: rockchip: Add NFC node for RK3036 SoC Add NAND FLASH Controller(NFC) node for RK3036 SoC. Signed-off-by: Yifeng Zhao Link: https://lore.kernel.org/r/20201210002219.5739-4-yifeng.zhao@rock-chips.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3036.dtsi | 52 +++++++++++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi index 093567022386..dda5a1f79aca 100644 --- a/arch/arm/boot/dts/rk3036.dtsi +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -292,6 +292,21 @@ status = "disabled"; }; + nfc: nand-controller@10500000 { + compatible = "rockchip,rk3036-nfc", + "rockchip,rk2928-nfc"; + reg = <0x10500000 0x4000>; + interrupts = ; + clocks = <&cru HCLK_NANDC>, <&cru SCLK_NANDC>; + clock-names = "ahb", "nfc"; + assigned-clocks = <&cru SCLK_NANDC>; + assigned-clock-rates = <150000000>; + pinctrl-0 = <&flash_ale &flash_bus8 &flash_cle &flash_csn0 + &flash_rdn &flash_rdy &flash_wrn>; + pinctrl-names = "default"; + status = "disabled"; + }; + cru: clock-controller@20000000 { compatible = "rockchip,rk3036-cru"; reg = <0x20000000 0x1000>; @@ -643,6 +658,43 @@ }; }; + nfc { + flash_ale: flash-ale { + rockchip,pins = <2 RK_PA0 1 &pcfg_pull_default>; + }; + + flash_bus8: flash-bus8 { + rockchip,pins = <1 RK_PD0 1 &pcfg_pull_default>, + <1 RK_PD1 1 &pcfg_pull_default>, + <1 RK_PD2 1 &pcfg_pull_default>, + <1 RK_PD3 1 &pcfg_pull_default>, + <1 RK_PD4 1 &pcfg_pull_default>, + <1 RK_PD5 1 &pcfg_pull_default>, + <1 RK_PD6 1 &pcfg_pull_default>, + <1 RK_PD7 1 &pcfg_pull_default>; + }; + + flash_cle: flash-cle { + rockchip,pins = <2 RK_PA1 1 &pcfg_pull_default>; + }; + + flash_csn0: flash-csn0 { + rockchip,pins = <2 RK_PA6 1 &pcfg_pull_default>; + }; + + flash_rdn: flash-rdn { + rockchip,pins = <2 RK_PA3 1 &pcfg_pull_default>; + }; + + flash_rdy: flash-rdy { + rockchip,pins = <2 RK_PA4 1 &pcfg_pull_default>; + }; + + flash_wrn: flash-wrn { + rockchip,pins = <2 RK_PA2 1 &pcfg_pull_default>; + }; + }; + emac { emac_xfer: emac-xfer { rockchip,pins = <2 RK_PB2 1 &pcfg_pull_default>, /* crs_dvalid */ From d4863ef399a29cae3001b3fedfd2864e651055ba Mon Sep 17 00:00:00 2001 From: Robert Foss Date: Mon, 21 Dec 2020 11:09:55 +0100 Subject: [PATCH 278/584] arm64: dts: qcom: sdm845-db845c: Fix reset-pin of ov8856 node Switch reset pin of ov8856 node from GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW, this issue prevented the ov8856 from probing properly as it did not respon to I2C messages. Fixes: d4919a44564b ("arm64: dts: qcom: sdm845-db845c: Add ov8856 & ov7251 camera nodes") Signed-off-by: Robert Foss Link: https://lore.kernel.org/r/20201221100955.148584-1-robert.foss@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sdm845-db845c.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts index 7cc236575ee2..f749672c5fdc 100644 --- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts +++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts @@ -1112,11 +1112,11 @@ reg = <0x10>; // CAM0_RST_N - reset-gpios = <&tlmm 9 0>; + reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; pinctrl-0 = <&cam0_default>; gpios = <&tlmm 13 0>, - <&tlmm 9 0>; + <&tlmm 9 GPIO_ACTIVE_LOW>; clocks = <&clock_camcc CAM_CC_MCLK0_CLK>; clock-names = "xvclk"; From 6243905da788cc75d920864fd087b334bb68bb7c Mon Sep 17 00:00:00 2001 From: AngeloGioacchino Del Regno Date: Tue, 19 Jan 2021 18:44:21 +0100 Subject: [PATCH 279/584] arm64: dts: pmi8998: Add the right interrupts for LAB/IBB SCP and OCP In commit 208921bae696 ("arm64: dts: qcom: pmi8998: Add nodes for LAB and IBB regulators") bindings for the lab/ibb regulators were added to the pmi8998 dt, but the original committer has never specified what the interrupts were for. LAB and IBB regulators provide two interrupts, SC-ERR (short circuit error) and VREG-OK but, in that commit, the regulators were provided with two different types of interrupts; specifically, IBB had the SC-ERR interrupt, while LAB had the VREG-OK one, none of which were (luckily) used, since the driver didn't actually use these at all. Assuming that the original intention was to have the SC IRQ in both LAB and IBB, as per the names appearing in documentation, fix the SCP interrupt. While at it, also add the OCP interrupt in order to be able to enable the Over-Current Protection feature, if requested. Signed-off-by: AngeloGioacchino Del Regno Reviewed-by: Bjorn Andersson Link: https://lore.kernel.org/r/20210119174421.226541-8-angelogioacchino.delregno@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/pmi8998.dtsi | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/pmi8998.dtsi b/arch/arm64/boot/dts/qcom/pmi8998.dtsi index d016b12967eb..d230c510d4b7 100644 --- a/arch/arm64/boot/dts/qcom/pmi8998.dtsi +++ b/arch/arm64/boot/dts/qcom/pmi8998.dtsi @@ -30,11 +30,15 @@ compatible = "qcom,pmi8998-lab-ibb"; ibb: ibb { - interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>; + interrupts = <0x3 0xdc 0x2 IRQ_TYPE_EDGE_RISING>, + <0x3 0xdc 0x0 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "sc-err", "ocp"; }; lab: lab { - interrupts = <0x3 0xde 0x0 IRQ_TYPE_EDGE_RISING>; + interrupts = <0x3 0xde 0x1 IRQ_TYPE_EDGE_RISING>, + <0x3 0xde 0x0 IRQ_TYPE_LEVEL_LOW>; + interrupt-names = "sc-err", "ocp"; }; }; }; From 5ccdc931515e8a6dc94156fe5742f8f999863f5c Mon Sep 17 00:00:00 2001 From: Alexey Minnekhanov Date: Sun, 10 Jan 2021 21:58:34 +0300 Subject: [PATCH 280/584] ARM: dts: qcom: msm8974-klte: Fix shdc numbering Since commit fa2d0aa96941 ("mmc: core: Allow setting slot index via device tree alias") proper aliases should be named "mmcN". Signed-off-by: Alexey Minnekhanov Link: https://lore.kernel.org/r/20210110185835.133059-1-alexeymin@postmarketos.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts index 97352de91314..f23d1002b8f8 100644 --- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts +++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts @@ -12,8 +12,8 @@ aliases { serial0 = &blsp1_uart1; - sdhc1 = &sdhc_1; /* SDC1 eMMC slot */ - sdhc2 = &sdhc_2; /* SDC2 SD card slot */ + mmc0 = &sdhc_1; /* SDC1 eMMC slot */ + mmc1 = &sdhc_2; /* SDC2 SD card slot */ }; chosen { From c6badbd2d321c19d4f55ee56b0ef12bb3352feac Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Wed, 2 Dec 2020 15:14:57 +0100 Subject: [PATCH 281/584] arm64: dts: zynqmp: Add address-cells property to interrupt controllers The commit 3eb619b2f7d8 ("scripts/dtc: Update to upstream version v1.6.0-11-g9d7888cbf19c") updated dtc version which also contained DTC commit "81e0919a3e21 checks: Add interrupt provider test" where reasons for this checking are mentioned as "A missing #address-cells property is less critical, but creates ambiguities when used in interrupt-map properties, so warn about this as well now." That's why add address-cells property to gic and gpio nodes to get rid of this warning. CC: Andre Przywara Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/e4f54ddce33b79a783aa7c76e0dc6e9787933610.1606918493.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 68923fbd0e89..cdc1a0ddfa01 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -347,6 +347,7 @@ gic: interrupt-controller@f9010000 { compatible = "arm,gic-400"; + #address-cells = <0>; #interrupt-cells = <3>; reg = <0x0 0xf9010000 0x0 0x10000>, <0x0 0xf9020000 0x0 0x20000>, @@ -507,6 +508,7 @@ gpio: gpio@ff0a0000 { compatible = "xlnx,zynqmp-gpio-1.0"; status = "disabled"; + #address-cells = <0>; #gpio-cells = <0x2>; gpio-controller; interrupt-parent = <&gic>; From 28a7eb65d474740f015e3d99bff685283b8c9289 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Tue, 19 Jan 2021 08:48:46 +0300 Subject: [PATCH 282/584] arm64: dts: qcom: pm8150x: add definitions for adc-tm5 part Define adc-tm5 thermal monitoring part. Individual channes and thermal zones are to be configured in per-device dts files. Signed-off-by: Dmitry Baryshkov Acked-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210119054848.592329-4-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/pm8150.dtsi | 10 ++++++++++ arch/arm64/boot/dts/qcom/pm8150b.dtsi | 10 ++++++++++ arch/arm64/boot/dts/qcom/pm8150l.dtsi | 10 ++++++++++ 3 files changed, 30 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi index a53eccf2b695..15e87153a194 100644 --- a/arch/arm64/boot/dts/qcom/pm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi @@ -97,6 +97,16 @@ }; }; + pm8150_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pm8150_rtc: rtc@6000 { compatible = "qcom,pm8941-rtc"; reg = <0x6000>; diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi index e112e8876db6..8e2f3250c914 100644 --- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi @@ -95,6 +95,16 @@ }; }; + pm8150b_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pm8150b_gpios: gpio@c000 { compatible = "qcom,pm8150b-gpio"; reg = <0xc000>; diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi index 62139538b7d9..9f214ceec2b7 100644 --- a/arch/arm64/boot/dts/qcom/pm8150l.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi @@ -89,6 +89,16 @@ }; }; + pm8150l_adc_tm: adc-tm@3500 { + compatible = "qcom,spmi-adc-tm5"; + reg = <0x3500>; + interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + pm8150l_gpios: gpio@c000 { compatible = "qcom,pm8150l-gpio"; reg = <0xc000>; From 681db16a5bcf3ab100318a9979b8838079fcee4d Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Tue, 19 Jan 2021 08:48:47 +0300 Subject: [PATCH 283/584] arm64: dts: sm8250-mtp: add thermal zones using pmic's adc-tm5 Port thermal zones definitions from msm-4.19 tree. Enable and add channel configuration to PMIC's ADC-TM definitions. Declare thermal zones and respective trip points. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210119054848.592329-5-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250-mtp.dts | 209 ++++++++++++++++++++++++ 1 file changed, 209 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts index 767a2e446248..5b4c5b08434c 100644 --- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts +++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts @@ -24,6 +24,106 @@ stdout-path = "serial0:115200n8"; }; + thermal-zones { + camera-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + conn-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150b_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + mmw-pa1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 2>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + mmw-pa2-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 2>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + skin-msm-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 1>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + skin-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 1>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + xo-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + }; + vph_pwr: vph-pwr-regulator { compatible = "regulator-fixed"; regulator-name = "vph_pwr"; @@ -392,6 +492,115 @@ /* rtc6226 @ 64 */ }; +&pm8150_adc { + xo-therm@4c { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + skin-therm@4d { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pa-therm1@4e { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150_adc_tm { + status = "okay"; + + xo-therm@0 { + reg = <0>; + io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + skin-therm@1 { + reg = <1>; + io-channels = <&pm8150_adc ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + pa-therm1@2 { + reg = <2>; + io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm8150b_adc { + conn-therm@4f { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150b_adc_tm { + status = "okay"; + + conn-therm@0 { + reg = <0>; + io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm8150l_adc_tm { + status = "okay"; + + camera-flash-therm@0 { + reg = <0>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + skin-msm-therm@1 { + reg = <1>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + pa-therm2@2 { + reg = <2>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm8150l_adc { + camera-flash-therm@4d { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + skin-msm-therm@4e { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pa-therm2@4f { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + &pm8150_rtc { status = "okay"; }; From 687cc021d70022136a4fe5c34a56ea897543c061 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Tue, 19 Jan 2021 08:48:48 +0300 Subject: [PATCH 284/584] arm64: dts: qrb5165-rb5: port thermal zone definitions Add thermal zones definitions basing on the downstream kernel. Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210119054848.592329-6-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 155 +++++++++++++++++++++++ 1 file changed, 155 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index a424595da8b0..58b94ce362b2 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -99,6 +99,78 @@ regulator-always-on; }; + thermal-zones { + conn-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150b_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "critical"; + }; + }; + }; + + pm8150l-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 1>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + skin-msm-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150l_adc_tm 0>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + wifi-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 1>; + + trips { + active-config0 { + temperature = <52000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + + xo-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm8150_adc_tm 0>; + + trips { + active-config0 { + temperature = <50000>; + hysteresis = <4000>; + type = "passive"; + }; + }; + }; + }; + vbat: vbat-regulator { compatible = "regulator-fixed"; regulator-name = "VBAT"; @@ -551,6 +623,38 @@ status = "okay"; }; +&pm8150_adc { + xo-therm@4c { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + wifi-therm@4e { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150_adc_tm { + status = "okay"; + + xo-therm@0 { + reg = <0>; + io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + wifi-therm@1 { + reg = <1>; + io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + &pm8150_gpios { gpio-reserved-ranges = <1 1>, <3 2>, <7 1>; gpio-line-names = @@ -566,6 +670,25 @@ "GPIO_10_P"; /* Green LED */ }; +&pm8150b_adc { + conn-therm@4f { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150b_adc_tm { + status = "okay"; + + conn-therm@0 { + reg = <0>; + io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + &pm8150b_gpios { gpio-line-names = "NC", @@ -582,6 +705,38 @@ "NC"; }; +&pm8150l_adc { + skin-msm-therm@4e { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + pm8150l-therm@4f { + reg = ; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm8150l_adc_tm { + status = "okay"; + + skin-msm-therm@0 { + reg = <0>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + pm8150l-therm@1 { + reg = <1>; + io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + &pm8150l_gpios { gpio-line-names = "NC", From e49c2912dbfa81cbe62849e4695f967f81c9350c Mon Sep 17 00:00:00 2001 From: Eric Biggers Date: Thu, 21 Jan 2021 01:01:39 -0800 Subject: [PATCH 285/584] arm64: dts: qcom: sdm630: add ICE registers and clocks Add the registers and clock for the Inline Crypto Engine (ICE) to the device tree node for the sdhci-msm host controller on sdm630. This allows sdhci-msm to support inline encryption on sdm630. Signed-off-by: Eric Biggers Link: https://lore.kernel.org/r/20210121090140.326380-9-ebiggers@kernel.org [bjorn: Changed indentation] Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sdm630.dtsi | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi index 37d5cc32f6b6..f91a928466c3 100644 --- a/arch/arm64/boot/dts/qcom/sdm630.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi @@ -808,17 +808,19 @@ sdhc_1: sdhci@c0c4000 { compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5"; reg = <0x0c0c4000 0x1000>, - <0x0c0c5000 0x1000>; - reg-names = "hc", "cqhci"; + <0x0c0c5000 0x1000>, + <0x0c0c8000 0x8000>; + reg-names = "hc", "cqhci", "ice"; interrupts = , ; interrupt-names = "hc_irq", "pwr_irq"; clocks = <&gcc GCC_SDCC1_APPS_CLK>, - <&gcc GCC_SDCC1_AHB_CLK>, - <&xo_board>; - clock-names = "core", "iface", "xo"; + <&gcc GCC_SDCC1_AHB_CLK>, + <&xo_board>, + <&gcc GCC_SDCC1_ICE_CORE_CLK>; + clock-names = "core", "iface", "xo", "ice"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>; From 984d4374ef06e20afecf66790f352c89fdf24a3d Mon Sep 17 00:00:00 2001 From: Nicolas Ferre Date: Sun, 17 Jan 2021 19:35:58 +0100 Subject: [PATCH 286/584] ARM: dts: at91-sama5d27_wlsom1: add i2c recovery Add the i2c gpio pinctrls to support the i2c bus recovery on this board. Signed-off-by: Nicolas Ferre Reviewed-by: Codrin Ciubotariu Link: https://lore.kernel.org/r/20210117183558.5369-1-nicolas.ferre@microchip.com --- arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi | 22 +++++++++++++++++++-- 1 file changed, 20 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi index a06700e53e4c..025a78310e3a 100644 --- a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi +++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi @@ -43,14 +43,20 @@ &i2c0 { pinctrl-0 = <&pinctrl_i2c0_default>; - pinctrl-names = "default"; + pinctrl-1 = <&pinctrl_i2c0_gpio>; + pinctrl-names = "default", "gpio"; + sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>; + scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; }; &i2c1 { dmas = <0>, <0>; - pinctrl-names = "default"; + pinctrl-names = "default", "gpio"; pinctrl-0 = <&pinctrl_i2c1_default>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>; + scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; status = "okay"; mcp16502@5b { @@ -258,12 +264,24 @@ bias-disable; }; + pinctrl_i2c0_gpio: i2c0_gpio { + pinmux = , + ; + bias-disable; + }; + pinctrl_i2c1_default: i2c1_default { pinmux = , ; bias-disable; }; + pinctrl_i2c1_gpio: i2c1_gpio { + pinmux = , + ; + bias-disable; + }; + pinctrl_macb0_default: macb0_default { pinmux = , , From 53efdfbb3b5f91c3db151243e090f755ee48219d Mon Sep 17 00:00:00 2001 From: Claudiu Beznea Date: Tue, 5 Jan 2021 13:18:45 +0200 Subject: [PATCH 287/584] ARM: dts: at91: sama5d2: remove atmel,wakeup-type references atmel,wakeup-type DT property is not referenced anywhere in the current and previous version of the code thus remove it. Signed-off-by: Claudiu Beznea Signed-off-by: Nicolas Ferre Link: https://lore.kernel.org/r/1609845525-10766-1-git-send-email-claudiu.beznea@microchip.com --- arch/arm/boot/dts/at91-kizbox3_common.dtsi | 1 - arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 1 - arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts | 1 - arch/arm/boot/dts/at91-sama5d2_icp.dts | 1 - arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts | 1 - arch/arm/boot/dts/at91-sama5d2_xplained.dts | 1 - 6 files changed, 6 deletions(-) diff --git a/arch/arm/boot/dts/at91-kizbox3_common.dtsi b/arch/arm/boot/dts/at91-kizbox3_common.dtsi index 9ce513dd514b..c4b3750495da 100644 --- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi +++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi @@ -341,7 +341,6 @@ input@0 { reg = <0>; - atmel,wakeup-type = "low"; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts index 0e159f879c15..84e1180f3e89 100644 --- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts @@ -142,7 +142,6 @@ input@0 { reg = <0>; - atmel,wakeup-type = "low"; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts index 6b38fa3f5568..180a08765cb8 100644 --- a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts @@ -209,7 +209,6 @@ input@0 { reg = <0>; - atmel,wakeup-type = "low"; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts index 6783cf16ff81..46722a163184 100644 --- a/arch/arm/boot/dts/at91-sama5d2_icp.dts +++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts @@ -697,7 +697,6 @@ input@0 { reg = <0>; - atmel,wakeup-type = "low"; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts index c894c7c788a9..8de57d164acd 100644 --- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts +++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts @@ -206,7 +206,6 @@ input@0 { reg = <0>; - atmel,wakeup-type = "low"; }; }; diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts index 058fae1b4a76..4e7cf21f124c 100644 --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts @@ -351,7 +351,6 @@ input@0 { reg = <0>; - atmel,wakeup-type = "low"; }; }; From 0cf73209ce2c60c5b717a02d9de10a6d524e08a6 Mon Sep 17 00:00:00 2001 From: Grygorii Strashko Date: Fri, 15 Jan 2021 21:30:16 +0200 Subject: [PATCH 288/584] arm64: dts: ti: k3: mmc: fix dtbs_check warnings Now the dtbs_check produces below warnings sdhci@4f80000: clock-names:0: 'clk_ahb' was expected sdhci@4f80000: clock-names:1: 'clk_xin' was expected $nodename:0: 'sdhci@4f80000' does not match '^mmc(@.*)?$' Fix above warnings by updating mmc DT definitions to follow sdhci-am654.yaml bindings: - rename sdhci dt nodes to 'mmc@' - swap clk_xin/clk_ahb clocks, the clk_ahb clock expected to be defined first Signed-off-by: Grygorii Strashko Signed-off-by: Nishanth Menon Reviewed-by: Suman Anna Reviewed-by: Aswath Govindraju Link: https://lore.kernel.org/r/20210115193016.5581-1-grygorii.strashko@ti.com --- arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++-- arch/arm64/boot/dts/ti/k3-j7200-main.dtsi | 8 ++++---- arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 18 +++++++++--------- 3 files changed, 15 insertions(+), 15 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi index 12591a854020..ceb579fb427d 100644 --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi @@ -256,7 +256,7 @@ #size-cells = <0>; }; - sdhci0: sdhci@4f80000 { + sdhci0: mmc@4f80000 { compatible = "ti,am654-sdhci-5.1"; reg = <0x0 0x4f80000 0x0 0x260>, <0x0 0x4f90000 0x0 0x134>; power-domains = <&k3_pds 47 TI_SCI_PD_EXCLUSIVE>; @@ -280,7 +280,7 @@ dma-coherent; }; - sdhci1: sdhci@4fa0000 { + sdhci1: mmc@4fa0000 { compatible = "ti,am654-sdhci-5.1"; reg = <0x0 0x4fa0000 0x0 0x260>, <0x0 0x4fb0000 0x0 0x134>; power-domains = <&k3_pds 48 TI_SCI_PD_EXCLUSIVE>; diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi index 4cc2e9094d0e..17477ab0fd8e 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi @@ -506,8 +506,8 @@ reg = <0x00 0x04f80000 0x00 0x260>, <0x00 0x4f88000 0x00 0x134>; interrupts = ; power-domains = <&k3_pds 91 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 91 3>, <&k3_clks 91 0>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 91 0>, <&k3_clks 91 3>; ti,otap-del-sel-legacy = <0x0>; ti,otap-del-sel-mmc-hs = <0x0>; ti,otap-del-sel-ddr52 = <0x6>; @@ -525,8 +525,8 @@ reg = <0x00 0x04fb0000 0x00 0x260>, <0x00 0x4fb8000 0x00 0x134>; interrupts = ; power-domains = <&k3_pds 92 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 92 2>, <&k3_clks 92 1>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 92 1>, <&k3_clks 92 2>; ti,otap-del-sel-legacy = <0x0>; ti,otap-del-sel-sd-hs = <0x0>; ti,otap-del-sel-sdr12 = <0xf>; diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi index 2d526ea44a85..8c84dafb7125 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi @@ -1032,13 +1032,13 @@ clock-names = "gpio"; }; - main_sdhci0: sdhci@4f80000 { + main_sdhci0: mmc@4f80000 { compatible = "ti,j721e-sdhci-8bit"; reg = <0x0 0x4f80000 0x0 0x1000>, <0x0 0x4f88000 0x0 0x400>; interrupts = ; power-domains = <&k3_pds 91 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 91 1>, <&k3_clks 91 0>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 91 0>, <&k3_clks 91 1>; assigned-clocks = <&k3_clks 91 1>; assigned-clock-parents = <&k3_clks 91 2>; bus-width = <8>; @@ -1054,13 +1054,13 @@ dma-coherent; }; - main_sdhci1: sdhci@4fb0000 { + main_sdhci1: mmc@4fb0000 { compatible = "ti,j721e-sdhci-4bit"; reg = <0x0 0x04fb0000 0x0 0x1000>, <0x0 0x4fb8000 0x0 0x400>; interrupts = ; power-domains = <&k3_pds 92 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 92 0>, <&k3_clks 92 5>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 92 5>, <&k3_clks 92 0>; assigned-clocks = <&k3_clks 92 0>; assigned-clock-parents = <&k3_clks 92 1>; ti,otap-del-sel-legacy = <0x0>; @@ -1074,13 +1074,13 @@ dma-coherent; }; - main_sdhci2: sdhci@4f98000 { + main_sdhci2: mmc@4f98000 { compatible = "ti,j721e-sdhci-4bit"; reg = <0x0 0x4f98000 0x0 0x1000>, <0x0 0x4f90000 0x0 0x400>; interrupts = ; power-domains = <&k3_pds 93 TI_SCI_PD_EXCLUSIVE>; - clock-names = "clk_xin", "clk_ahb"; - clocks = <&k3_clks 93 0>, <&k3_clks 93 5>; + clock-names = "clk_ahb", "clk_xin"; + clocks = <&k3_clks 93 5>, <&k3_clks 93 0>; assigned-clocks = <&k3_clks 93 0>; assigned-clock-parents = <&k3_clks 93 1>; ti,otap-del-sel-legacy = <0x0>; From 8367611892442ea788139ea1063308b6e7b6f04f Mon Sep 17 00:00:00 2001 From: Daniel Palmer Date: Thu, 24 Dec 2020 11:03:54 +0900 Subject: [PATCH 289/584] ARM: mstar: Unify common parts of BreadBee boards into a dtsi The BreadBee and the BreadBee Crust are the same PCB with a different SoC mounted. There are two top level dts to handle this. To avoid deduplicating the parts that are more related to the PCB than the SoC (i.e. the voltage regs and LEDs) add a common dtsi that can be included in both top level dts. Signed-off-by: Daniel Palmer Link: https://lore.kernel.org/r/20201224020354.2212037-1-daniel@0x0f.com' Signed-off-by: Arnd Bergmann --- .../dts/mstar-infinity-breadbee-common.dtsi | 49 +++++++++++++++++++ .../mstar-infinity-msc313-breadbee_crust.dts | 1 + .../dts/mstar-infinity3-msc313e-breadbee.dts | 1 + 3 files changed, 51 insertions(+) create mode 100644 arch/arm/boot/dts/mstar-infinity-breadbee-common.dtsi diff --git a/arch/arm/boot/dts/mstar-infinity-breadbee-common.dtsi b/arch/arm/boot/dts/mstar-infinity-breadbee-common.dtsi new file mode 100644 index 000000000000..507ff2fba837 --- /dev/null +++ b/arch/arm/boot/dts/mstar-infinity-breadbee-common.dtsi @@ -0,0 +1,49 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (c) 2020 thingy.jp. + * Author: Daniel Palmer + */ + +#include + +/ { + vcc_core: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vcc_core"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-boot-on; + }; + + vcc_dram: fixedregulator@1 { + compatible = "regulator-fixed"; + regulator-name = "vcc_dram"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + vcc_io: fixedregulator@2 { + compatible = "regulator-fixed"; + regulator-name = "vcc_io"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + leds { + compatible = "gpio-leds"; + red { + gpios = <&gpio MSC313_GPIO_SR_IO16 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "activity"; + }; + yellow { + gpios = <&gpio MSC313_GPIO_SR_IO17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&cpu0 { + cpu-supply = <&vcc_core>; +}; diff --git a/arch/arm/boot/dts/mstar-infinity-msc313-breadbee_crust.dts b/arch/arm/boot/dts/mstar-infinity-msc313-breadbee_crust.dts index f9db2ff86f2d..db4910dcb8a7 100644 --- a/arch/arm/boot/dts/mstar-infinity-msc313-breadbee_crust.dts +++ b/arch/arm/boot/dts/mstar-infinity-msc313-breadbee_crust.dts @@ -6,6 +6,7 @@ /dts-v1/; #include "mstar-infinity-msc313.dtsi" +#include "mstar-infinity-breadbee-common.dtsi" / { model = "BreadBee Crust"; diff --git a/arch/arm/boot/dts/mstar-infinity3-msc313e-breadbee.dts b/arch/arm/boot/dts/mstar-infinity3-msc313e-breadbee.dts index f0eda80a95cc..e64ca4ce1830 100644 --- a/arch/arm/boot/dts/mstar-infinity3-msc313e-breadbee.dts +++ b/arch/arm/boot/dts/mstar-infinity3-msc313e-breadbee.dts @@ -6,6 +6,7 @@ /dts-v1/; #include "mstar-infinity3-msc313e.dtsi" +#include "mstar-infinity-breadbee-common.dtsi" / { model = "BreadBee"; From 0e43e08c13a1b77b2274a2122d3f51dfe00cda09 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:39:59 +0530 Subject: [PATCH 290/584] dt-bindings: usb: qcom,dwc3: Add binding for SDX55 Add devicetree binding for SDX55 USB controller based on Qcom designware IP. Acked-by: Felipe Balbi Cc: Rob Herring Cc: devicetree@vger.kernel.org Cc: linux-usb@vger.kernel.org Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-2-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/usb/qcom,dwc3.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml index 2cf525d21e05..fd93b941f07a 100644 --- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml @@ -17,6 +17,7 @@ properties: - qcom,msm8998-dwc3 - qcom,sc7180-dwc3 - qcom,sdm845-dwc3 + - qcom,sdx55-dwc3 - const: qcom,dwc3 reg: From fea4b41022f35a017d7221d23c6d9bee84ad90d0 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:40:00 +0530 Subject: [PATCH 291/584] ARM: dts: qcom: sdx55: Add USB3 and PHY support Add devicetree nodes for enabling USB3 controller, Qcom QMP PHY and SNPS HS PHY on SDX55. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-3-manivannan.sadhasivam@linaro.org [bjorn: Added missing #power-domain-cells to &gcc] Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 86 +++++++++++++++++++++++++++++++ 1 file changed, 86 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index 4838ba03c62e..f340705236e4 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -130,6 +130,7 @@ reg = <0x100000 0x1f0000>; #clock-cells = <1>; #reset-cells = <1>; + #power-domain-cells = <1>; clock-names = "bi_tcxo", "sleep_clk"; clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; }; @@ -144,6 +145,48 @@ status = "disabled"; }; + usb_hsphy: phy@ff4000 { + compatible = "qcom,usb-snps-hs-7nm-phy"; + reg = <0x00ff4000 0x114>; + status = "disabled"; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_BCR>; + }; + + usb_qmpphy: phy@ff6000 { + compatible = "qcom,sdx55-qmp-usb3-uni-phy"; + reg = <0x00ff6000 0x1c0>; + status = "disabled"; + #clock-cells = <1>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_USB3_PHY_AUX_CLK>, + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_USB3_PRIM_CLKREF_CLK>; + clock-names = "aux", "cfg_ahb", "ref"; + + resets = <&gcc GCC_USB3PHY_PHY_BCR>, + <&gcc GCC_USB3_PHY_BCR>; + reset-names = "phy", "common"; + + usb_ssphy: phy@ff6200 { + reg = <0x00ff6200 0x170>, + <0x00ff6400 0x200>, + <0x00ff6800 0x800>; + #phy-cells = <0>; + #clock-cells = <0>; + clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>; + clock-names = "pipe0"; + clock-output-names = "usb3_uni_phy_pipe_clk_src"; + }; + }; + qpic_bam: dma-controller@1b04000 { compatible = "qcom,bam-v1.7.0"; reg = <0x01b04000 0x1c000>; @@ -190,6 +233,49 @@ status = "disabled"; }; + usb: usb@a6f8800 { + compatible = "qcom,sdx55-dwc3", "qcom,dwc3"; + reg = <0x0a6f8800 0x400>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clocks = <&gcc GCC_USB30_SLV_AHB_CLK>, + <&gcc GCC_USB30_MASTER_CLK>, + <&gcc GCC_USB30_MSTR_AXI_CLK>, + <&gcc GCC_USB30_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_SLEEP_CLK>; + clock-names = "cfg_noc", "core", "iface", "mock_utmi", + "sleep"; + + assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_MASTER_CLK>; + assigned-clock-rates = <19200000>, <200000000>; + + interrupts = , + , + , + ; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + power-domains = <&gcc USB30_GDSC>; + + resets = <&gcc GCC_USB30_BCR>; + + usb_dwc3: dwc3@a600000 { + compatible = "snps,dwc3"; + reg = <0x0a600000 0xcd00>; + interrupts = ; + iommus = <&apps_smmu 0x1a0 0x0>; + snps,dis_u2_susphy_quirk; + snps,dis_enblslpm_quirk; + phys = <&usb_hsphy>, <&usb_ssphy>; + phy-names = "usb2-phy", "usb3-phy"; + }; + }; + pdc: interrupt-controller@b210000 { compatible = "qcom,sdx55-pdc", "qcom,pdc"; reg = <0x0b210000 0x30000>; From 20779ecf3b4309184d6df254e884698ef0cfd52c Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:40:01 +0530 Subject: [PATCH 292/584] ARM: dts: qcom: sdx55-mtp: Enable USB3 and PHY support Enable the support for USB3 controller, QMP PHY and HS PHY on SDX55 MTP. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-4-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 29 ++++++++++++++++++++++++---- 1 file changed, 25 insertions(+), 4 deletions(-) diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 96b6a295f813..7fec5e7a2724 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -111,7 +111,7 @@ regulator-max-microvolt = <1960000>; }; - ldo1 { + vreg_l1e_bb_1p2: ldo1 { regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-initial-mode = ; @@ -129,13 +129,13 @@ regulator-initial-mode = ; }; - ldo4 { + vreg_l4e_bb_0p875: ldo4 { regulator-min-microvolt = <872000>; regulator-max-microvolt = <872000>; regulator-initial-mode = ; }; - ldo5 { + vreg_l5e_bb_1p7: ldo5 { regulator-min-microvolt = <1704000>; regulator-max-microvolt = <1900000>; regulator-initial-mode = ; @@ -165,7 +165,7 @@ regulator-initial-mode = ; }; - ldo10 { + vreg_l10e_3p1: ldo10 { regulator-min-microvolt = <3088000>; regulator-max-microvolt = <3088000>; regulator-initial-mode = ; @@ -228,3 +228,24 @@ nand-bus-width = <8>; }; }; + +&usb { + status = "okay"; +}; + +&usb_dwc3 { + dr_mode = "peripheral"; +}; + +&usb_hsphy { + status = "okay"; + vdda-pll-supply = <&vreg_l4e_bb_0p875>; + vdda33-supply = <&vreg_l10e_3p1>; + vdda18-supply = <&vreg_l5e_bb_1p7>; +}; + +&usb_qmpphy { + status = "okay"; + vdda-phy-supply = <&vreg_l4e_bb_0p875>; + vdda-pll-supply = <&vreg_l1e_bb_1p2>; +}; From 54211b6125030364604d91bcfb83b5efa0a240a8 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:40:02 +0530 Subject: [PATCH 293/584] dt-bindings: watchdog: Add binding for Qcom SDX55 Add devicetree binding for watchdog present in Qcom SDX55 platform. Cc: Wim Van Sebroeck Cc: Guenter Roeck Cc: Rob Herring Cc: linux-watchdog@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-5-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml b/Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml index 8e3760a3822b..b8e4118945a0 100644 --- a/Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml +++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml @@ -18,6 +18,7 @@ properties: - qcom,apss-wdt-qcs404 - qcom,apss-wdt-sc7180 - qcom,apss-wdt-sdm845 + - qcom,apss-wdt-sdx55 - qcom,apss-wdt-sm8150 - qcom,kpss-timer - qcom,kpss-wdt From b1d20460f169176134e896abf333c291a2270ba9 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:40:03 +0530 Subject: [PATCH 294/584] ARM: dts: qcom: sdx55: Add Watchdog support Enable Watchdog support for Application Processor Subsystem (APSS) block on SDX55 platform. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-6-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index f340705236e4..ec43a7b2d86e 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -347,6 +347,12 @@ <0x17802000 0x1000>; }; + watchdog@17817000 { + compatible = "qcom,apss-wdt-sdx55", "qcom,kpss-wdt"; + reg = <0x17817000 0x1000>; + clocks = <&sleep_clk>; + }; + timer@17820000 { #address-cells = <1>; #size-cells = <1>; From c4aa86f0dd80921042df8fb60acb4e2d905e585a Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:40:04 +0530 Subject: [PATCH 295/584] ARM: dts: qcom: sdx55: Add pshold support Add support for pshold block to drive pshold towards the PMIC, which is used to trigger a configurable event such as reboot or poweroff of the SDX55 platform. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-7-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-sdx55.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi index ec43a7b2d86e..e4180bbc4655 100644 --- a/arch/arm/boot/dts/qcom-sdx55.dtsi +++ b/arch/arm/boot/dts/qcom-sdx55.dtsi @@ -285,6 +285,11 @@ interrupt-controller; }; + restart@c264000 { + compatible = "qcom,pshold"; + reg = <0x0c264000 0x1000>; + }; + spmi_bus: qcom,spmi@c440000 { compatible = "qcom,spmi-pmic-arb"; reg = <0x0c440000 0x0000d00>, From 381c1623a3746162e146534d8000566682737cc8 Mon Sep 17 00:00:00 2001 From: Jonathan McDowell Date: Sun, 5 Jul 2020 15:25:44 +0100 Subject: [PATCH 296/584] ARM: dts: qcom: add prng definition to ipq806x Add missing prng definition for ipq806x SoC Signed-off-by: Jonathan McDowell Link: https://lore.kernel.org/r/20200705142544.GA3389@earth.li Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq8064.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index c51481405e7f..edc8dd735aa6 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -386,6 +386,13 @@ }; }; + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; + }; + sata_phy: sata-phy@1b400000 { compatible = "qcom,ipq806x-sata-phy"; reg = <0x1b400000 0x200>; From b8afc254b40167fd37b4d4263e750dab1f9ef157 Mon Sep 17 00:00:00 2001 From: John Crispin Date: Wed, 9 Sep 2020 18:38:31 +0200 Subject: [PATCH 297/584] ARM: dts: qcom: ipq4019: add USB devicetree nodes Since we now have driver for the USB PHY, and USB controller is already supported by the DWC3 driver lets add the necessary nodes to DTSI. Signed-off-by: John Crispin Signed-off-by: Robert Marko Cc: Luka Perkov Reviewed-by: Vinod Koul Link: https://lore.kernel.org/r/20200909163831.1894142-1-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq4019.dtsi | 74 +++++++++++++++++++++++++++++ 1 file changed, 74 insertions(+) diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index 74d8e2c8e4b3..4a973253024a 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -605,5 +605,79 @@ reg = <4>; }; }; + + usb3_ss_phy: ssphy@9a000 { + compatible = "qcom,usb-ss-ipq4019-phy"; + #phy-cells = <0>; + reg = <0x9a000 0x800>; + reg-names = "phy_base"; + resets = <&gcc USB3_UNIPHY_PHY_ARES>; + reset-names = "por_rst"; + status = "disabled"; + }; + + usb3_hs_phy: hsphy@a6000 { + compatible = "qcom,usb-hs-ipq4019-phy"; + #phy-cells = <0>; + reg = <0xa6000 0x40>; + reg-names = "phy_base"; + resets = <&gcc USB3_HSPHY_POR_ARES>, <&gcc USB3_HSPHY_S_ARES>; + reset-names = "por_rst", "srif_rst"; + status = "disabled"; + }; + + usb3: usb3@8af8800 { + compatible = "qcom,dwc3"; + reg = <0x8af8800 0x100>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gcc GCC_USB3_MASTER_CLK>, + <&gcc GCC_USB3_SLEEP_CLK>, + <&gcc GCC_USB3_MOCK_UTMI_CLK>; + clock-names = "master", "sleep", "mock_utmi"; + ranges; + status = "disabled"; + + dwc3@8a00000 { + compatible = "snps,dwc3"; + reg = <0x8a00000 0xf8000>; + interrupts = ; + phys = <&usb3_hs_phy>, <&usb3_ss_phy>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + }; + }; + + usb2_hs_phy: hsphy@a8000 { + compatible = "qcom,usb-hs-ipq4019-phy"; + #phy-cells = <0>; + reg = <0xa8000 0x40>; + reg-names = "phy_base"; + resets = <&gcc USB2_HSPHY_POR_ARES>, <&gcc USB2_HSPHY_S_ARES>; + reset-names = "por_rst", "srif_rst"; + status = "disabled"; + }; + + usb2: usb2@60f8800 { + compatible = "qcom,dwc3"; + reg = <0x60f8800 0x100>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&gcc GCC_USB2_MASTER_CLK>, + <&gcc GCC_USB2_SLEEP_CLK>, + <&gcc GCC_USB2_MOCK_UTMI_CLK>; + clock-names = "master", "sleep", "mock_utmi"; + ranges; + status = "disabled"; + + dwc3@6000000 { + compatible = "snps,dwc3"; + reg = <0x6000000 0xf8000>; + interrupts = ; + phys = <&usb2_hs_phy>; + phy-names = "usb2-phy"; + dr_mode = "host"; + }; + }; }; }; From d1ae4c808e7802008225078d93fbadd4aeea1e2d Mon Sep 17 00:00:00 2001 From: Robert Marko Date: Wed, 9 Sep 2020 21:56:37 +0200 Subject: [PATCH 298/584] ARM: dts: qcom: ipq4019: add more labels Lets add labels to more commonly used nodes for easier modification in board DTS files. Signed-off-by: Robert Marko Cc: Luka Perkov Link: https://lore.kernel.org/r/20200909195640.3127341-2-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq4019.dtsi | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index 4a973253024a..0ad6c242dc3e 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -190,7 +190,7 @@ reg = <0x1800000 0x60000>; }; - rng@22000 { + prng: rng@22000 { compatible = "qcom,prng"; reg = <0x22000 0x140>; clocks = <&gcc GCC_PRNG_AHB_CLK>; @@ -300,7 +300,7 @@ status = "disabled"; }; - crypto@8e3a000 { + crypto: crypto@8e3a000 { compatible = "qcom,crypto-v5.1"; reg = <0x08e3a000 0x6000>; clocks = <&gcc GCC_CRYPTO_AHB_CLK>, @@ -386,7 +386,7 @@ dma-names = "rx", "tx"; }; - watchdog@b017000 { + watchdog: watchdog@b017000 { compatible = "qcom,kpss-wdt", "qcom,kpss-wdt-ipq4019"; reg = <0xb017000 0x40>; clocks = <&sleep_clk>; From 308b2365ce113ca6bec619718095dfc175aef42a Mon Sep 17 00:00:00 2001 From: Robert Marko Date: Wed, 9 Sep 2020 21:56:38 +0200 Subject: [PATCH 299/584] ARM: dts: qcom: add 8devices Jalapeno 8devices Jalapeno is a dual-band SoM, based on Qualcomm IPQ4018 + QCA8072 platform. Specification: QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz 256 MB of DDR3 RAM 8 MB of SPI NOR flash 128 MB of Winbond SPI NAND flash WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN) Signed-off-by: Robert Marko Cc: Luka Perkov Link: https://lore.kernel.org/r/20200909195640.3127341-3-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts | 214 ++++++++++++++++++++ 2 files changed, 215 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 13a7cee00daf..31a4451378ef 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -912,6 +912,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-jalapeno.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ qcom-ipq4019-ap.dk04.1-c1.dtb \ qcom-ipq4019-ap.dk04.1-c3.dtb \ diff --git a/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts b/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts new file mode 100644 index 000000000000..394412619894 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4018-jalapeno.dts @@ -0,0 +1,214 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +// Copyright (c) 2018, Robert Marko + +#include "qcom-ipq4019.dtsi" +#include +#include + +/ { + model = "8devices Jalapeno"; + compatible = "8dev,jalapeno"; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + pinmux_1 { + pins = "gpio53"; + function = "mdio"; + }; + + pinmux_2 { + pins = "gpio52"; + function = "mdc"; + }; + + pinconf { + pins = "gpio52", "gpio53"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pin { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <2>; + bias-disable; + }; + + pin_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&watchdog { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + status = "okay"; + + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + label = "u-boot-env"; + reg = <0x000e0000 0x00010000>; + }; + + partition@f0000 { + label = "u-boot"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + }; + }; + + spi-nand@1 { + status = "okay"; + + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi1"; + reg = <0x00000000 0x04000000>; + }; + + partition@4000000 { + label = "ubi2"; + reg = <0x04000000 0x04000000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; +}; + +&wifi0 { + status = "okay"; + + qcom,ath10k-calibration-variant = "8devices-Jalapeno"; +}; + +&wifi1 { + status = "okay"; + + qcom,ath10k-calibration-variant = "8devices-Jalapeno"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; From 7fccbd67ba6b7913f5d289e21aa8bff885b97a4d Mon Sep 17 00:00:00 2001 From: Robert Marko Date: Wed, 9 Sep 2020 21:56:39 +0200 Subject: [PATCH 300/584] ARM: dts: qcom: add Alfa Network AP120C-AC ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 or 512 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 1x button (reset) - 1x USB 2.0 - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) This adds DTS for both the generic and custom Bit edition for Sartura. Signed-off-by: Robert Marko Cc: Luka Perkov Link: https://lore.kernel.org/r/20200909195640.3127341-4-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/Makefile | 2 + .../boot/dts/qcom-ipq4018-ap120c-ac-bit.dts | 28 ++ arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts | 27 ++ arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi | 254 ++++++++++++++++++ 4 files changed, 311 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts create mode 100644 arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts create mode 100644 arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 31a4451378ef..6cd15dd11e0f 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -912,6 +912,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-ap120c-ac.dtb \ + qcom-ipq4018-ap120c-ac-bit.dtb \ qcom-ipq4018-jalapeno.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ qcom-ipq4019-ap.dk04.1-c1.dtb \ diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts new file mode 100644 index 000000000000..028ac8e24797 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts @@ -0,0 +1,28 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4018-ap120c-ac.dtsi" + +/ { + model = "ALFA Network AP120C-AC Bit"; + + leds { + compatible = "gpio-leds"; + + power { + label = "ap120c-ac:green:power"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan { + label = "ap120c-ac:green:wlan"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + }; + + support { + label = "ap120c-ac:green:support"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts new file mode 100644 index 000000000000..b7916fc26d68 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts @@ -0,0 +1,27 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4018-ap120c-ac.dtsi" + +/ { + leds { + compatible = "gpio-leds"; + + status: status { + label = "ap120c-ac:blue:status"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wlan2g { + label = "ap120c-ac:green:wlan2g"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "ap120c-ac:red:wlan5g"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi new file mode 100644 index 000000000000..1f3b1ce82108 --- /dev/null +++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi @@ -0,0 +1,254 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include + +/ { + model = "ALFA Network AP120C-AC"; + compatible = "alfa-network,ap120c-ac"; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; +}; + +&tlmm { + i2c0_pins: i2c0_pinmux { + mux_i2c { + function = "blsp_i2c0"; + pins = "gpio58", "gpio59"; + drive-strength = <16>; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_mdio { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + + mux_mdc { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial0_pins: serial0_pinmux { + mux_uart { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi0_pins: spi0_pinmux { + mux_spi { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio4"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + usb-power { + line-name = "USB-power"; + gpios = <1 GPIO_ACTIVE_HIGH>; + gpio-hog; + output-high; + }; +}; + +&watchdog { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_i2c3 { + status = "okay"; + + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + tpm@29 { + compatible = "atmel,at97sc3204t"; + reg = <0x29>; + }; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + label = "u-boot-env"; + reg = <0x000e0000 0x00010000>; + }; + + partition@f0000 { + label = "u-boot"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + + partition@180000 { + label = "priv_data1"; + reg = <0x00180000 0x00010000>; + read-only; + }; + + partition@190000 { + label = "priv_data2"; + reg = <0x00190000 0x00010000>; + read-only; + }; + }; + }; + + nand@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi1"; + reg = <0x00000000 0x04000000>; + }; + + partition@4000000 { + label = "ubi2"; + reg = <0x04000000 0x04000000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial0_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; +}; + +&wifi0 { + status = "okay"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "ALFA-Network-AP120C-AC"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; + + dwc3@8a00000 { + phys = <&usb3_hs_phy>; + phy-names = "usb2-phy"; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb2 { + status = "okay"; +}; From 59595f65b3aa602831302adf006bf27d9363acfe Mon Sep 17 00:00:00 2001 From: Adrian Schmutzler Date: Wed, 2 Sep 2020 18:51:59 +0200 Subject: [PATCH 301/584] ARM: dts: qcom: remove commented mmc-ddr-1_8v for sdcc3 This property appears to be commented out, so we can remove it as well. Signed-off-by: Adrian Schmutzler Link: https://lore.kernel.org/r/20200902165159.7733-2-freifunk@adrianschmutzler.de Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq8064.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index edc8dd735aa6..01f9aba36961 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -786,7 +786,6 @@ cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <192000000>; - #mmc-ddr-1_8v; sd-uhs-sdr104; sd-uhs-ddr50; vqmmc-supply = <&vsdcc_fixed>; From dd1ebbcf7b609becf40fafc993fc8177934c6d49 Mon Sep 17 00:00:00 2001 From: Adrian Schmutzler Date: Wed, 2 Sep 2020 18:51:58 +0200 Subject: [PATCH 302/584] ARM: dts: qcom: add additional DT labels in qcom-ipq8064.dtsi This adds some additional DT labels which are handy when referring to the nodes in derived DTS(I) files. It will also make the definitions more consistent, e.g. by adding gsbi2_serial and gsbi5_serial where we previously "only" had gsbi4_serial defined. While at it, add missing spaces after some DT labels and remove one useless empty line. Signed-off-by: Adrian Schmutzler Link: https://lore.kernel.org/r/20200902165159.7733-1-freifunk@adrianschmutzler.de Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq8064.dtsi | 23 +++++++++++------------ 1 file changed, 11 insertions(+), 12 deletions(-) diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi index 01f9aba36961..98995ead4413 100644 --- a/arch/arm/boot/dts/qcom-ipq8064.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi @@ -20,7 +20,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu0: cpu@0 { compatible = "qcom,krait"; enable-method = "qcom,kpss-acc-v1"; device_type = "cpu"; @@ -30,7 +30,7 @@ qcom,saw = <&saw0>; }; - cpu@1 { + cpu1: cpu@1 { compatible = "qcom,krait"; enable-method = "qcom,kpss-acc-v1"; device_type = "cpu"; @@ -67,7 +67,7 @@ no-map; }; - smem@41000000 { + smem: smem@41000000 { reg = <0x41000000 0x200000>; no-map; }; @@ -251,7 +251,7 @@ syscon-tcsr = <&tcsr>; - serial@12490000 { + gsbi2_serial: serial@12490000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x12490000 0x1000>, <0x12480000 0x1000>; @@ -273,7 +273,6 @@ #address-cells = <1>; #size-cells = <0>; }; - }; gsbi4: gsbi@16300000 { @@ -326,7 +325,7 @@ syscon-tcsr = <&tcsr>; - serial@1a240000 { + gsbi5_serial: serial@1a240000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x1a240000 0x1000>, <0x1a200000 0x1000>; @@ -404,7 +403,7 @@ status = "disabled"; }; - sata@29000000 { + sata: sata@29000000 { compatible = "qcom,ipq806x-ahci", "generic-ahci"; reg = <0x29000000 0x180>; @@ -727,7 +726,7 @@ regulator-always-on; }; - sdcc1bam:dma@12402000 { + sdcc1bam: dma@12402000 { compatible = "qcom,bam-v1.3.0"; reg = <0x12402000 0x8000>; interrupts = ; @@ -737,7 +736,7 @@ qcom,ee = <0>; }; - sdcc3bam:dma@12182000 { + sdcc3bam: dma@12182000 { compatible = "qcom,bam-v1.3.0"; reg = <0x12182000 0x8000>; interrupts = ; @@ -747,13 +746,13 @@ qcom,ee = <0>; }; - amba { + amba: amba { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; ranges; - sdcc@12400000 { + sdcc1: sdcc@12400000 { status = "disabled"; compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x00051180>; @@ -773,7 +772,7 @@ dma-names = "tx", "rx"; }; - sdcc@12180000 { + sdcc3: sdcc@12180000 { compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x00051180>; status = "disabled"; From 0fd69f04d07f7fc61a639b8cc0c6ce37d321dbbb Mon Sep 17 00:00:00 2001 From: Adrian Schmutzler Date: Sun, 30 Aug 2020 21:16:43 +0200 Subject: [PATCH 303/584] ARM: dts: qcom: replace status value "ok" by "okay" While the DT parser recognizes "ok" as a valid value for the "status" property, it is actually mentioned nowhere. Use the proper value "okay" instead, as done in the majority of files already. Signed-off-by: Adrian Schmutzler Link: https://lore.kernel.org/r/20200830191643.20717-1-freifunk@adrianschmutzler.de [bjorn: Rebased and included fixup of sdx55-mtp] Signed-off-by: Bjorn Andersson --- .../arm/boot/dts/qcom-apq8060-dragonboard.dts | 12 +++---- .../boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 8 ++--- arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts | 8 ++--- arch/arm/boot/dts/qcom-apq8064-ifc6410.dts | 10 +++--- .../dts/qcom-apq8064-sony-xperia-yuga.dts | 4 +-- .../arm/boot/dts/qcom-apq8074-dragonboard.dts | 10 +++--- arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi | 18 +++++------ .../boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts | 4 +-- arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi | 10 +++--- .../boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts | 8 ++--- .../boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts | 2 +- arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi | 10 +++--- arch/arm/boot/dts/qcom-ipq8064-ap148.dts | 2 +- arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi | 12 +++---- arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi | 16 +++++----- arch/arm/boot/dts/qcom-msm8660-surf.dts | 4 +-- arch/arm/boot/dts/qcom-msm8960-cdp.dts | 8 ++--- .../boot/dts/qcom-msm8974-fairphone-fp2.dts | 14 ++++---- .../qcom-msm8974-lge-nexus5-hammerhead.dts | 32 +++++++++---------- .../boot/dts/qcom-msm8974-samsung-klte.dts | 10 +++--- .../dts/qcom-msm8974-sony-xperia-amami.dts | 14 ++++---- .../dts/qcom-msm8974-sony-xperia-castor.dts | 18 +++++------ .../dts/qcom-msm8974-sony-xperia-honami.dts | 16 +++++----- arch/arm/boot/dts/qcom-sdx55-mtp.dts | 6 ++-- 24 files changed, 128 insertions(+), 128 deletions(-) diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts index 4e6c50d45cb2..dace8ffeb991 100644 --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts @@ -461,11 +461,11 @@ }; gsbi@19800000 { - status = "ok"; + status = "okay"; qcom,mode = ; i2c@19880000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&dragon_gsbi8_i2c_pins>; @@ -497,17 +497,17 @@ }; gsbi@19c00000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@19c40000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&dragon_gsbi12_serial_pins>; }; i2c@19c80000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&dragon_gsbi12_i2c_pins>; @@ -571,7 +571,7 @@ external-bus@1a100000 { /* The EBI2 will instantiate first, then populate its children */ - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&dragon_ebi2_pins>; diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts index a701d4bac320..3bce47d16ab3 100644 --- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts +++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts @@ -302,11 +302,11 @@ }; gsbi@16500000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@16540000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&gsbi6_uart_4pins>; @@ -314,10 +314,10 @@ }; gsbi@16600000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@16640000 { - status = "ok"; + status = "okay"; }; }; diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts index 209eb21cea00..0148148a8e0a 100644 --- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts +++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts @@ -141,10 +141,10 @@ }; gsbi@16600000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@16640000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&gsbi7_uart_2pins>; }; @@ -152,7 +152,7 @@ /* OTG */ usb@12500000 { - status = "ok"; + status = "okay"; dr_mode = "otg"; ulpi { phy { @@ -209,7 +209,7 @@ }; pci@1b500000 { - status = "ok"; + status = "okay"; vdda-supply = <&pm8921_s3>; vdda_phy-supply = <&pm8921_lvs6>; vdda_refclk-supply = <&v3p3_fixed>; diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts index 83aaf4a74398..d0a17b5a5fa3 100644 --- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts +++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts @@ -215,21 +215,21 @@ }; gsbi@16500000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@16540000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&gsbi6_uart_4pins>; }; }; gsbi@16600000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@16640000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&gsbi7_uart_2pins>; }; @@ -279,7 +279,7 @@ }; pci@1b500000 { - status = "ok"; + status = "okay"; vdda-supply = <&pm8921_s3>; vdda_phy-supply = <&pm8921_lvs6>; vdda_refclk-supply = <&ext_3p3v>; diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts index 8bf488fb86ad..72e47bdc5c12 100644 --- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts +++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts @@ -362,11 +362,11 @@ }; gsbi@1a200000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@1a240000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&gsbi5_uart_pin_a>; diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts index 244f04e19c9d..83793b835d40 100644 --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts @@ -19,13 +19,13 @@ soc { serial@f991e000 { - status = "ok"; + status = "okay"; }; sdhci@f9824900 { bus-width = <8>; non-removable; - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; @@ -39,14 +39,14 @@ pinctrl-names = "default"; pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>; bus-width = <4>; - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l21>; vqmmc-supply = <&pm8941_l13>; }; usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs2_phy>; phy-select = <&tcsr 0xb000 1>; extcon = <&smbb>, <&usb_id>; @@ -56,7 +56,7 @@ adp-disable; ulpi { phy@b { - status = "ok"; + status = "okay"; v3p3-supply = <&pm8941_l24>; v1p8-supply = <&pm8941_l6>; extcon = <&smbb>; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi index 418f9a022336..c93b2164db44 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi @@ -30,7 +30,7 @@ soc { rng@22000 { - status = "ok"; + status = "okay"; }; pinctrl@1000000 { @@ -66,13 +66,13 @@ }; blsp_dma: dma@7884000 { - status = "ok"; + status = "okay"; }; spi@78b5000 { pinctrl-0 = <&spi_0_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; cs-gpios = <&tlmm 54 0>; mx25l25635e@0 { @@ -87,27 +87,27 @@ serial@78af000 { pinctrl-0 = <&serial_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; cryptobam: dma@8e04000 { - status = "ok"; + status = "okay"; }; crypto@8e3a000 { - status = "ok"; + status = "okay"; }; watchdog@b017000 { - status = "ok"; + status = "okay"; }; wifi@a000000 { - status = "ok"; + status = "okay"; }; wifi@a800000 { - status = "ok"; + status = "okay"; }; }; }; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts index 7a96f300bc8d..b0f476ff017f 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts @@ -9,11 +9,11 @@ soc { dma@7984000 { - status = "ok"; + status = "okay"; }; qpic-nand@79b0000 { - status = "ok"; + status = "okay"; }; }; }; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi index 7c1eb1963c67..7a337dc08741 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi @@ -70,23 +70,23 @@ serial@78af000 { pinctrl-0 = <&serial_0_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; serial@78b0000 { pinctrl-0 = <&serial_1_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; dma@7884000 { - status = "ok"; + status = "okay"; }; spi@78b5000 { /* BLSP1 QUP1 */ pinctrl-0 = <&spi_0_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; cs-gpios = <&tlmm 12 0>; m25p80@0 { @@ -99,7 +99,7 @@ }; pci@40000000 { - status = "ok"; + status = "okay"; perst-gpio = <&tlmm 38 0x1>; }; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts index 8c7ef6537ae6..f343a2244386 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts @@ -9,12 +9,12 @@ soc { pci@40000000 { - status = "ok"; + status = "okay"; perst-gpio = <&tlmm 38 0x1>; }; spi@78b6000 { - status = "ok"; + status = "okay"; }; pinctrl@1000000 { @@ -43,13 +43,13 @@ serial@78b0000 { pinctrl-0 = <&serial_1_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; spi@78b5000 { pinctrl-0 = <&spi_0_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; cs-gpios = <&tlmm 12 0>; m25p80@0 { diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts index af7a9028d492..582acb681a98 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c2.dts @@ -19,7 +19,7 @@ serial@78b0000 { pinctrl-0 = <&serial_1_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; }; }; diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi index 9f1a5a668772..94872518b5a2 100644 --- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi @@ -49,27 +49,27 @@ serial@78af000 { pinctrl-0 = <&serial_0_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; dma@7884000 { - status = "ok"; + status = "okay"; }; i2c@78b7000 { /* BLSP1 QUP2 */ pinctrl-0 = <&i2c_0_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; dma@7984000 { - status = "ok"; + status = "okay"; }; qpic-nand@79b0000 { pinctrl-0 = <&nand_pins>; pinctrl-names = "default"; - status = "ok"; + status = "okay"; }; }; }; diff --git a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts index 554c65e7aa0e..e5b9b9cf6097 100644 --- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts +++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts @@ -24,7 +24,7 @@ gsbi@16300000 { i2c@16380000 { - status = "ok"; + status = "okay"; clock-frequency = <200000>; pinctrl-0 = <&i2c4_pins>; pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi index e239a0486936..65330065390a 100644 --- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi +++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi @@ -16,19 +16,19 @@ soc { gsbi@16300000 { qcom,mode = ; - status = "ok"; + status = "okay"; serial@16340000 { - status = "ok"; + status = "okay"; }; }; gsbi5: gsbi@1a200000 { qcom,mode = ; - status = "ok"; + status = "okay"; spi4: spi@1a280000 { - status = "ok"; + status = "okay"; spi-max-frequency = <50000000>; pinctrl-0 = <&spi_pins>; @@ -57,12 +57,12 @@ }; sata-phy@1b400000 { - status = "ok"; + status = "okay"; }; sata@29000000 { ports-implemented = <0x1>; - status = "ok"; + status = "okay"; }; gpio_keys { diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi index 26b034bd19d2..a725b73b5a2e 100644 --- a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi +++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi @@ -125,12 +125,12 @@ }; &gsbi3 { - status = "ok"; + status = "okay"; qcom,mode = ; }; &gsbi3_spi { - status = "ok"; + status = "okay"; pinctrl-0 = <&gsbi3_pins>; pinctrl-names = "default"; assigned-clocks = <&gcc GSBI3_QUP_CLK>; @@ -138,34 +138,34 @@ }; &gsbi4 { - status = "ok"; + status = "okay"; qcom,mode = ; }; &gsbi4_serial { - status = "ok"; + status = "okay"; pinctrl-0 = <&gsbi4_pins>; pinctrl-names = "default"; }; &gsbi5 { - status = "ok"; + status = "okay"; qcom,mode = ; }; &gsbi5_i2c { - status = "ok"; + status = "okay"; clock-frequency = <200000>; pinctrl-0 = <&gsbi5_i2c_pins>; pinctrl-names = "default"; }; &gsbi5_serial { - status = "ok"; + status = "okay"; pinctrl-0 = <&gsbi5_uart_pins>; pinctrl-names = "default"; }; &sdcc1 { - status = "ok"; + status = "okay"; }; diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts index f01a11b18d6a..6a321ccb0bd0 100644 --- a/arch/arm/boot/dts/qcom-msm8660-surf.dts +++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts @@ -17,10 +17,10 @@ soc { gsbi@19c00000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@19c40000 { - status = "ok"; + status = "okay"; }; }; diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts index 82d5d8267adf..e7d2e937ea4c 100644 --- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts +++ b/arch/arm/boot/dts/qcom-msm8960-cdp.dts @@ -17,10 +17,10 @@ soc { gsbi@16400000 { - status = "ok"; + status = "okay"; qcom,mode = ; serial@16440000 { - status = "ok"; + status = "okay"; }; }; @@ -273,12 +273,12 @@ }; gsbi@16000000 { - status = "ok"; + status = "okay"; qcom,mode = ; pinctrl-names = "default"; pinctrl-0 = <&spi1_default>; spi@16080000 { - status = "ok"; + status = "okay"; eth@0 { compatible = "micrel,ks8851"; reg = <0>; diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts index d2d48770ec0f..ea15b645b229 100644 --- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts +++ b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts @@ -256,11 +256,11 @@ &soc { serial@f991e000 { - status = "ok"; + status = "okay"; }; remoteproc@fb21b000 { - status = "ok"; + status = "okay"; vddmx-supply = <&pm8841_s1>; vddcx-supply = <&pm8841_s2>; @@ -273,7 +273,7 @@ label = "pronto"; wcnss { - status = "ok"; + status = "okay"; }; }; }; @@ -335,7 +335,7 @@ }; sdhci@f9824900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; @@ -348,7 +348,7 @@ }; sdhci@f98a4900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l21>; vqmmc-supply = <&pm8941_l13>; @@ -360,7 +360,7 @@ }; usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; @@ -373,7 +373,7 @@ ulpi { phy@a { - status = "ok"; + status = "okay"; v1p8-supply = <&pm8941_l6>; v3p3-supply = <&pm8941_l24>; diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts index e769f638f205..0cda654371ae 100644 --- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts +++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts @@ -239,7 +239,7 @@ &soc { serial@f991d000 { - status = "ok"; + status = "okay"; }; pinctrl@fd510000 { @@ -410,7 +410,7 @@ }; sdhci@f9824900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; @@ -423,7 +423,7 @@ }; sdhci@f98a4900 { - status = "ok"; + status = "okay"; max-frequency = <100000000>; bus-width = <4>; @@ -471,7 +471,7 @@ }; serial@f9960000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&blsp2_uart10_pin_a>; @@ -490,7 +490,7 @@ }; i2c@f9967000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c11_pins>; clock-frequency = <355000>; @@ -498,7 +498,7 @@ led-controller@38 { compatible = "ti,lm3630a"; - status = "ok"; + status = "okay"; reg = <0x38>; #address-cells = <1>; @@ -514,7 +514,7 @@ }; i2c@f9968000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c12_pins>; clock-frequency = <100000>; @@ -551,7 +551,7 @@ }; i2c@f9923000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c1_pins>; clock-frequency = <100000>; @@ -585,7 +585,7 @@ }; i2c@f9924000 { - status = "ok"; + status = "okay"; clock-frequency = <355000>; qcom,src-freq = <50000000>; @@ -620,7 +620,7 @@ }; i2c@f9925000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c3_pins>; clock-frequency = <100000>; @@ -638,7 +638,7 @@ }; usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; @@ -652,7 +652,7 @@ ulpi { phy@a { - status = "ok"; + status = "okay"; v1p8-supply = <&pm8941_l6>; v3p3-supply = <&pm8941_l24>; @@ -663,14 +663,14 @@ }; mdss@fd900000 { - status = "ok"; + status = "okay"; mdp@fd900000 { - status = "ok"; + status = "okay"; }; dsi@fd922800 { - status = "ok"; + status = "okay"; vdda-supply = <&pm8941_l2>; vdd-supply = <&pm8941_lvs3>; @@ -704,7 +704,7 @@ }; dsi-phy@fd922a00 { - status = "ok"; + status = "okay"; vddio-supply = <&pm8941_l12>; }; diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts index f23d1002b8f8..3929c9435e29 100644 --- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts +++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts @@ -303,7 +303,7 @@ &soc { serial@f991e000 { - status = "ok"; + status = "okay"; }; gpio-keys { @@ -456,7 +456,7 @@ }; sdhc_1: sdhci@f9824900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pma8084_l20>; vqmmc-supply = <&pma8084_s4>; @@ -469,7 +469,7 @@ }; sdhc_2: sdhci@f9864900 { - status = "ok"; + status = "okay"; max-frequency = <100000000>; @@ -518,7 +518,7 @@ }; usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; @@ -531,7 +531,7 @@ ulpi { phy@a { - status = "ok"; + status = "okay"; v1p8-supply = <&pma8084_l6>; v3p3-supply = <&pma8084_l24>; diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts index 5669f5f58a86..398a3eaf306b 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts @@ -261,7 +261,7 @@ &soc { sdhci@f9824900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; @@ -274,7 +274,7 @@ }; sdhci@f98a4900 { - status = "ok"; + status = "okay"; bus-width = <4>; @@ -288,7 +288,7 @@ }; serial@f991e000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&blsp1_uart2_pin_a>; @@ -366,7 +366,7 @@ }; usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; @@ -379,7 +379,7 @@ ulpi { phy@a { - status = "ok"; + status = "okay"; v1p8-supply = <&pm8941_l6>; v3p3-supply = <&pm8941_l24>; @@ -415,7 +415,7 @@ }; coincell@2800 { - status = "ok"; + status = "okay"; qcom,rset-ohms = <2100>; qcom,vset-millivolts = <3000>; }; @@ -423,7 +423,7 @@ pm8941@1 { wled@d800 { - status = "ok"; + status = "okay"; qcom,cs-out; qcom,current-limit = <20>; diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts index 701b396719c7..f4ec08f13003 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts @@ -279,7 +279,7 @@ &soc { sdhci@f9824900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; @@ -292,7 +292,7 @@ }; sdhci@f9864900 { - status = "ok"; + status = "okay"; max-frequency = <100000000>; non-removable; @@ -316,7 +316,7 @@ }; sdhci@f98a4900 { - status = "ok"; + status = "okay"; bus-width = <4>; @@ -330,14 +330,14 @@ }; serial@f991e000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&blsp1_uart2_pin_a>; }; usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; @@ -350,7 +350,7 @@ ulpi { phy@a { - status = "ok"; + status = "okay"; v1p8-supply = <&pm8941_l6>; v3p3-supply = <&pm8941_l24>; @@ -482,7 +482,7 @@ }; i2c@f9964000 { - status = "ok"; + status = "okay"; clock-frequency = <355000>; qcom,src-freq = <50000000>; @@ -522,7 +522,7 @@ }; i2c@f9967000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c11_pins>; clock-frequency = <355000>; @@ -635,7 +635,7 @@ }; coincell@2800 { - status = "ok"; + status = "okay"; qcom,rset-ohms = <2100>; qcom,vset-millivolts = <3000>; }; diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index 611bae9fe66b..9743beebd84d 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -261,7 +261,7 @@ &soc { usb@f9a55000 { - status = "ok"; + status = "okay"; phys = <&usb_hs1_phy>; phy-select = <&tcsr 0xb000 0>; @@ -274,7 +274,7 @@ ulpi { phy@a { - status = "ok"; + status = "okay"; v1p8-supply = <&pm8941_l6>; v3p3-supply = <&pm8941_l24>; @@ -286,7 +286,7 @@ }; sdhci@f9824900 { - status = "ok"; + status = "okay"; vmmc-supply = <&pm8941_l20>; vqmmc-supply = <&pm8941_s3>; @@ -299,7 +299,7 @@ }; sdhci@f98a4900 { - status = "ok"; + status = "okay"; bus-width = <4>; @@ -313,14 +313,14 @@ }; serial@f991e000 { - status = "ok"; + status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&blsp1_uart2_pin_a>; }; i2c@f9924000 { - status = "ok"; + status = "okay"; clock-frequency = <355000>; qcom,src-freq = <50000000>; @@ -464,7 +464,7 @@ }; coincell@2800 { - status = "ok"; + status = "okay"; qcom,rset-ohms = <2100>; qcom,vset-millivolts = <3000>; }; @@ -472,7 +472,7 @@ pm8941@1 { wled@d800 { - status = "ok"; + status = "okay"; qcom,cs-out; qcom,current-limit = <20>; diff --git a/arch/arm/boot/dts/qcom-sdx55-mtp.dts b/arch/arm/boot/dts/qcom-sdx55-mtp.dts index 7fec5e7a2724..9649c1e11311 100644 --- a/arch/arm/boot/dts/qcom-sdx55-mtp.dts +++ b/arch/arm/boot/dts/qcom-sdx55-mtp.dts @@ -210,15 +210,15 @@ }; &blsp1_uart3 { - status = "ok"; + status = "okay"; }; &qpic_bam { - status = "ok"; + status = "okay"; }; &qpic_nand { - status = "ok"; + status = "okay"; nand@0 { reg = <0>; From 3a786086c6f8d226bf8be16d5b6d77ce51e6686b Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Mon, 18 Jan 2021 10:40:05 +0530 Subject: [PATCH 304/584] arm64: dts: qcom: Add missing "-thermal" suffix for thermal zones The thermal devicetree binding requires the "-thermal" suffix for all thermal zones. Hence, add the missing suffix for PMIC based thermal zones. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210118051005.55958-8-manivannan.sadhasivam@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/pm8150.dtsi | 2 +- arch/arm64/boot/dts/qcom/pm8150b.dtsi | 2 +- arch/arm64/boot/dts/qcom/pm8150l.dtsi | 2 +- arch/arm64/boot/dts/qcom/pm8994.dtsi | 2 +- arch/arm64/boot/dts/qcom/pm8998.dtsi | 2 +- arch/arm64/boot/dts/qcom/pms405.dtsi | 2 +- 6 files changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi index 15e87153a194..bdc76d504b78 100644 --- a/arch/arm64/boot/dts/qcom/pm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi @@ -11,7 +11,7 @@ / { thermal-zones { - pm8150 { + pm8150-thermal { polling-delay-passive = <100>; polling-delay = <0>; diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi index 8e2f3250c914..b21e56a46145 100644 --- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi @@ -10,7 +10,7 @@ / { thermal-zones { - pm8150b { + pm8150b-thermal { polling-delay-passive = <100>; polling-delay = <0>; diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi index 9f214ceec2b7..52f094a2b713 100644 --- a/arch/arm64/boot/dts/qcom/pm8150l.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi @@ -10,7 +10,7 @@ / { thermal-zones { - pm8150l { + pm8150l-thermal { polling-delay-passive = <100>; polling-delay = <0>; diff --git a/arch/arm64/boot/dts/qcom/pm8994.dtsi b/arch/arm64/boot/dts/qcom/pm8994.dtsi index 5ffdf37d8e31..91fff1f209e0 100644 --- a/arch/arm64/boot/dts/qcom/pm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8994.dtsi @@ -6,7 +6,7 @@ / { thermal-zones { - pm8994 { + pm8994-thermal { polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi index 67283d60e2ac..6f5bb6b37ec2 100644 --- a/arch/arm64/boot/dts/qcom/pm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi @@ -9,7 +9,7 @@ / { thermal-zones { - pm8998 { + pm8998-thermal { polling-delay-passive = <250>; polling-delay = <1000>; diff --git a/arch/arm64/boot/dts/qcom/pms405.dtsi b/arch/arm64/boot/dts/qcom/pms405.dtsi index ff4005186895..172be177fc8f 100644 --- a/arch/arm64/boot/dts/qcom/pms405.dtsi +++ b/arch/arm64/boot/dts/qcom/pms405.dtsi @@ -8,7 +8,7 @@ / { thermal-zones { - pms405 { + pms405-thermal { polling-delay-passive = <250>; polling-delay = <1000>; From 28734f87a03ef4e6e443d11633d5e3c7eae44c8f Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Wed, 13 Jan 2021 21:17:45 +0100 Subject: [PATCH 305/584] ARM: dts: Fix up MMC host node names The standard mandates that these nodes be named mmc@... not sdi_foo@... Acked-by: Ulf Hansson Signed-off-by: Linus Walleij --- arch/arm/boot/dts/ste-dbx5x0.dtsi | 12 ++++++------ arch/arm/boot/dts/ste-href.dtsi | 8 ++++---- arch/arm/boot/dts/ste-hrefprev60.dtsi | 2 +- arch/arm/boot/dts/ste-hrefv60plus.dtsi | 2 +- arch/arm/boot/dts/ste-snowball.dts | 8 ++++---- arch/arm/boot/dts/ste-ux500-samsung-golden.dts | 6 +++--- arch/arm/boot/dts/ste-ux500-samsung-janice.dts | 6 +++--- arch/arm/boot/dts/ste-ux500-samsung-skomer.dts | 6 +++--- 8 files changed, 25 insertions(+), 25 deletions(-) diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index 404b9c4a5fee..68607e4ad80c 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -883,7 +883,7 @@ status = "disabled"; }; - sdi0_per1@80126000 { + mmc@80126000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x80126000 0x1000>; interrupts = ; @@ -899,7 +899,7 @@ status = "disabled"; }; - sdi1_per2@80118000 { + mmc@80118000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x80118000 0x1000>; interrupts = ; @@ -915,7 +915,7 @@ status = "disabled"; }; - sdi2_per3@80005000 { + mmc@80005000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x80005000 0x1000>; interrupts = ; @@ -931,7 +931,7 @@ status = "disabled"; }; - sdi3_per2@80119000 { + mmc@80119000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x80119000 0x1000>; interrupts = ; @@ -947,7 +947,7 @@ status = "disabled"; }; - sdi4_per2@80114000 { + mmc@80114000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x80114000 0x1000>; interrupts = ; @@ -963,7 +963,7 @@ status = "disabled"; }; - sdi5_per3@80008000 { + mmc@80008000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x80008000 0x1000>; interrupts = ; diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi index 8c03124b6960..83b179692dff 100644 --- a/arch/arm/boot/dts/ste-href.dtsi +++ b/arch/arm/boot/dts/ste-href.dtsi @@ -114,7 +114,7 @@ }; // External Micro SD slot - sdi0_per1@80126000 { + mmc@80126000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; @@ -137,7 +137,7 @@ }; // WLAN SDIO channel - sdi1_per2@80118000 { + mmc@80118000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; @@ -150,7 +150,7 @@ }; // PoP:ed eMMC - sdi2_per3@80005000 { + mmc@80005000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <8>; @@ -165,7 +165,7 @@ }; // On-board eMMC - sdi4_per2@80114000 { + mmc@80114000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <8>; diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi index 931998dd364b..29b67abfc461 100644 --- a/arch/arm/boot/dts/ste-hrefprev60.dtsi +++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi @@ -61,7 +61,7 @@ }; // External Micro SD slot - sdi0_per1@80126000 { + mmc@80126000 { cd-gpios = <&tc3589x_gpio 3 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index 05ea12e6df1c..8f504edefd3f 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -190,7 +190,7 @@ }; // External Micro SD slot - sdi0_per1@80126000 { + mmc@80126000 { cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95 }; diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index be90e73c923e..f32b07f31acf 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -213,7 +213,7 @@ }; // External Micro SD slot - sdi0_per1@80126000 { + mmc@80126000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; @@ -241,7 +241,7 @@ }; // WLAN SDIO channel - sdi1_per2@80118000 { + mmc@80118000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; @@ -253,7 +253,7 @@ }; // Unused PoP eMMC - register and put it to sleep by default */ - sdi2_per3@80005000 { + mmc@80005000 { arm,primecell-periphid = <0x10480180>; pinctrl-names = "default"; pinctrl-0 = <&mc2_a_1_sleep>; @@ -262,7 +262,7 @@ }; // On-board eMMC - sdi4_per2@80114000 { + mmc@80114000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <8>; diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts index 496f9d3ba7b7..00ee013cbd1d 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts @@ -72,7 +72,7 @@ soc { /* External Micro SD card slot */ - sdi0_per1@80126000 { + mmc@80126000 { status = "okay"; arm,primecell-periphid = <0x10480180>; @@ -100,7 +100,7 @@ }; /* WLAN SDIO */ - sdi1_per2@80118000 { + mmc@80118000 { status = "okay"; arm,primecell-periphid = <0x10480180>; @@ -134,7 +134,7 @@ }; /* eMMC */ - sdi2_per3@80005000 { + mmc@80005000 { status = "okay"; arm,primecell-periphid = <0x10480180>; diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts index 31ee34e79fe1..95d5abe5dc0d 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts @@ -329,7 +329,7 @@ soc { /* External Micro SD slot */ - sdi0_per1@80126000 { + mmc@80126000 { arm,primecell-periphid = <0x10480180>; max-frequency = <50000000>; bus-width = <4>; @@ -352,7 +352,7 @@ }; /* WLAN SDIO channel */ - sdi1_per2@80118000 { + mmc@80118000 { arm,primecell-periphid = <0x10480180>; max-frequency = <50000000>; bus-width = <4>; @@ -390,7 +390,7 @@ }; /* eMMC */ - sdi2_per3@80005000 { + mmc@80005000 { arm,primecell-periphid = <0x10480180>; max-frequency = <50000000>; bus-width = <8>; diff --git a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts index b50634c81b44..36420492fd72 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts @@ -147,7 +147,7 @@ soc { // External Micro SD slot - sdi0_per1@80126000 { + mmc@80126000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <4>; @@ -169,7 +169,7 @@ }; // WLAN SDIO channel - sdi1_per2@80118000 { + mmc@80118000 { arm,primecell-periphid = <0x10480180>; max-frequency = <50000000>; bus-width = <4>; @@ -196,7 +196,7 @@ }; // eMMC - sdi2_per3@80005000 { + mmc@80005000 { arm,primecell-periphid = <0x10480180>; max-frequency = <100000000>; bus-width = <8>; From f5e4bf9060d34f93519e319d71ee71d779a41084 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 22 Jan 2021 23:20:38 +0100 Subject: [PATCH 306/584] ARM: dts: nomadik: Fix up MMC node names Fix the node names for the MMC/SD card controller to conform to the standard node name mmc@.. Signed-off-by: Linus Walleij Link: https://lore.kernel.org/r/20210122222038.2888747-1-linus.walleij@linaro.org' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/ste-nomadik-nhk15.dts | 2 +- arch/arm/boot/dts/ste-nomadik-s8815.dts | 2 +- arch/arm/boot/dts/ste-nomadik-stn8815.dtsi | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/ste-nomadik-nhk15.dts b/arch/arm/boot/dts/ste-nomadik-nhk15.dts index 41ed21a4fdc1..8142c017882c 100644 --- a/arch/arm/boot/dts/ste-nomadik-nhk15.dts +++ b/arch/arm/boot/dts/ste-nomadik-nhk15.dts @@ -195,7 +195,7 @@ pinctrl-0 = <&uart0_nhk_mode>; status = "okay"; }; - mmcsd: sdi@101f6000 { + mmcsd: mmc@101f6000 { cd-gpios = <&stmpe_gpio44 7 GPIO_ACTIVE_LOW>; wp-gpios = <&stmpe_gpio44 18 GPIO_ACTIVE_HIGH>; }; diff --git a/arch/arm/boot/dts/ste-nomadik-s8815.dts b/arch/arm/boot/dts/ste-nomadik-s8815.dts index 4445446fa828..f16314ffbf4b 100644 --- a/arch/arm/boot/dts/ste-nomadik-s8815.dts +++ b/arch/arm/boot/dts/ste-nomadik-s8815.dts @@ -139,7 +139,7 @@ status = "okay"; }; /* Configure card detect for the uSD slot */ - mmcsd: sdi@101f6000 { + mmc@101f6000 { cd-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; }; }; diff --git a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi index 4f38aeecadb3..c9b906432341 100644 --- a/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi +++ b/arch/arm/boot/dts/ste-nomadik-stn8815.dtsi @@ -825,7 +825,7 @@ interrupts = <10>; }; - mmcsd: sdi@101f6000 { + mmcsd: mmc@101f6000 { compatible = "arm,pl18x", "arm,primecell"; reg = <0x101f6000 0x1000>; clocks = <&sdiclk>, <&pclksdi>; From 7b18e43d08ab8e559fad4725f3d5510d9cae830c Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Tue, 1 Dec 2020 18:34:24 +0900 Subject: [PATCH 307/584] MAINTAINERS: Add entries for Toshiba Visconti5 watchdog driver Add entries for Toshiba Visconti5 watchdog driver and binding. Signed-off-by: Nobuhiro Iwamatsu --- MAINTAINERS | 2 ++ 1 file changed, 2 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 546aa66428c9..315a3704f8b6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2643,8 +2643,10 @@ S: Supported T: git git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti.git F: Documentation/devicetree/bindings/arm/toshiba.yaml F: Documentation/devicetree/bindings/pinctrl/toshiba,tmpv7700-pinctrl.yaml +F: Documentation/devicetree/bindings/watchdog/toshiba,visconti-wdt.yaml F: arch/arm64/boot/dts/toshiba/ F: drivers/pinctrl/visconti/ +F: drivers/watchdog/visconti_wdt.c N: visconti ARM/UNIPHIER ARCHITECTURE From 4fd18fc38757217c746aa063ba9e4729814dc737 Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Tue, 1 Dec 2020 18:39:07 +0900 Subject: [PATCH 308/584] arm64: dts: visconti: Add watchdog support for TMPV7708 SoC Add watchdog node in TMPV7708's dtsi, and tmpv7708-rm-mbrc boards's dts. Signed-off-by: Nobuhiro Iwamatsu --- arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts | 5 +++++ arch/arm64/boot/dts/toshiba/tmpv7708.dtsi | 12 ++++++++++++ 2 files changed, 17 insertions(+) diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts index ed0bf7f13f54..37da418393e0 100644 --- a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts +++ b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts @@ -41,3 +41,8 @@ clocks = <&uart_clk>; clock-names = "apb_pclk"; }; + +&wdt { + status = "okay"; + clocks = <&wdt_clk>; +}; diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi index 242f25f4e12a..c360e68bef1d 100644 --- a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi +++ b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi @@ -134,6 +134,12 @@ #clock-cells = <0>; }; + wdt_clk: wdt-clk { + compatible = "fixed-clock"; + clock-frequency = <150000000>; + #clock-cells = <0>; + }; + soc { #address-cells = <2>; #size-cells = <2>; @@ -384,6 +390,12 @@ #size-cells = <0>; status = "disabled"; }; + + wdt: wdt@28330000 { + compatible = "toshiba,visconti-wdt"; + reg = <0 0x28330000 0 0x1000>; + status = "disabled"; + }; }; }; From 59fc16d7d92e8315db2855eb1d0ec62c48acc492 Mon Sep 17 00:00:00 2001 From: Serge Semin Date: Sun, 24 Jan 2021 20:50:48 -0800 Subject: [PATCH 309/584] arm: dts: keystone: Correct DWC USB3 compatible string Syonpsys IP cores are supposed to be defined with "snps" vendor-prefix. Use it instead of the deprecated "synopsys" one. Signed-off-by: Serge Semin Reviewed-by: Krzysztof Kozlowski Signed-off-by: Santosh Shilimkar --- arch/arm/boot/dts/keystone-k2e.dtsi | 2 +- arch/arm/boot/dts/keystone.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/keystone-k2e.dtsi b/arch/arm/boot/dts/keystone-k2e.dtsi index 2d94faf31fab..fa1b8499c5a7 100644 --- a/arch/arm/boot/dts/keystone-k2e.dtsi +++ b/arch/arm/boot/dts/keystone-k2e.dtsi @@ -79,7 +79,7 @@ status = "disabled"; usb1: dwc3@25010000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x25010000 0x70000>; interrupts = ; usb-phy = <&usb1_phy>, <&usb1_phy>; diff --git a/arch/arm/boot/dts/keystone.dtsi b/arch/arm/boot/dts/keystone.dtsi index c298675a29a5..8d046a1b690c 100644 --- a/arch/arm/boot/dts/keystone.dtsi +++ b/arch/arm/boot/dts/keystone.dtsi @@ -218,7 +218,7 @@ status = "disabled"; usb0: dwc3@2690000 { - compatible = "synopsys,dwc3"; + compatible = "snps,dwc3"; reg = <0x2690000 0x70000>; interrupts = ; usb-phy = <&usb_phy>, <&usb_phy>; From 091584182ba6a298351f1e555c13ceb880c1f397 Mon Sep 17 00:00:00 2001 From: Serge Semin Date: Sun, 24 Jan 2021 20:50:48 -0800 Subject: [PATCH 310/584] arm: dts: keystone: Harmonize DWC USB3 DT nodes name In accordance with the DWC USB3 bindings the corresponding node name is suppose to comply with the Generic USB HCD DT schema, which requires the USB nodes to have the name acceptable by the regexp: "^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly named. Signed-off-by: Serge Semin Acked-by: Krzysztof Kozlowski Signed-off-by: Santosh Shilimkar --- arch/arm/boot/dts/keystone-k2e.dtsi | 4 ++-- arch/arm/boot/dts/keystone.dtsi | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/keystone-k2e.dtsi b/arch/arm/boot/dts/keystone-k2e.dtsi index fa1b8499c5a7..b8f152e7af7f 100644 --- a/arch/arm/boot/dts/keystone-k2e.dtsi +++ b/arch/arm/boot/dts/keystone-k2e.dtsi @@ -52,7 +52,7 @@ usb: usb@2680000 { interrupts = ; - dwc3@2690000 { + usb@2690000 { interrupts = ; }; }; @@ -78,7 +78,7 @@ dma-ranges; status = "disabled"; - usb1: dwc3@25010000 { + usb1: usb@25010000 { compatible = "snps,dwc3"; reg = <0x25010000 0x70000>; interrupts = ; diff --git a/arch/arm/boot/dts/keystone.dtsi b/arch/arm/boot/dts/keystone.dtsi index 8d046a1b690c..fc9fdc857ae8 100644 --- a/arch/arm/boot/dts/keystone.dtsi +++ b/arch/arm/boot/dts/keystone.dtsi @@ -217,7 +217,7 @@ dma-ranges; status = "disabled"; - usb0: dwc3@2690000 { + usb0: usb@2690000 { compatible = "snps,dwc3"; reg = <0x2690000 0x70000>; interrupts = ; From d68c9edfda21247a63521072806479e842761a42 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Tue, 19 Jan 2021 14:33:22 +0100 Subject: [PATCH 311/584] arm64: dts: renesas: Disable SD functions for plain eMMC Some SDHI instances are solely used for eMMC. Disable SD and SDIO for faster initialization. Signed-off-by: Wolfram Sang Acked-by: Adam Ford (beacon) Link: https://lore.kernel.org/r/20210119133322.87289-1-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi | 2 ++ arch/arm64/boot/dts/renesas/hihope-common.dtsi | 2 ++ arch/arm64/boot/dts/renesas/r8a77980-condor.dts | 2 ++ arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts | 2 ++ arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 2 ++ arch/arm64/boot/dts/renesas/salvator-common.dtsi | 2 ++ arch/arm64/boot/dts/renesas/ulcb.dtsi | 2 ++ 7 files changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index f4201e1c2226..c9bf5234dbd0 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -312,6 +312,8 @@ vqmmc-supply = <®_1p8v>; bus-width = <8>; mmc-hs200-1_8v; + no-sd; + no-sdio; non-removable; fixed-emmc-driver-type = <1>; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/hihope-common.dtsi b/arch/arm64/boot/dts/renesas/hihope-common.dtsi index 2eda9f66ae81..7a3da9b06f67 100644 --- a/arch/arm64/boot/dts/renesas/hihope-common.dtsi +++ b/arch/arm64/boot/dts/renesas/hihope-common.dtsi @@ -328,6 +328,8 @@ vqmmc-supply = <®_1p8v>; bus-width = <8>; mmc-hs200-1_8v; + no-sd; + no-sdio; non-removable; fixed-emmc-driver-type = <1>; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts index 422ec53740cb..04d47c0c9bb9 100644 --- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts +++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts @@ -217,6 +217,8 @@ vqmmc-supply = <&vddq_vin01>; mmc-hs200-1_8v; bus-width = <8>; + no-sd; + no-sdio; non-removable; status = "okay"; }; diff --git a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts index e0ccca2222d2..f74f8b9993f1 100644 --- a/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts +++ b/arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts @@ -712,6 +712,8 @@ mmc-hs200-1_8v; mmc-hs400-1_8v; bus-width = <8>; + no-sd; + no-sdio; non-removable; full-pwr-cycle-in-suspend; status = "okay"; diff --git a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts index 8f471881b7a3..6783c3ad0856 100644 --- a/arch/arm64/boot/dts/renesas/r8a77995-draak.dts +++ b/arch/arm64/boot/dts/renesas/r8a77995-draak.dts @@ -496,6 +496,8 @@ vqmmc-supply = <®_1p8v>; bus-width = <8>; mmc-hs200-1_8v; + no-sd; + no-sdio; non-removable; status = "okay"; }; diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi index 6c643ed74fc5..c22bb38994e8 100644 --- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi +++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi @@ -831,6 +831,8 @@ bus-width = <8>; mmc-hs200-1_8v; mmc-hs400-1_8v; + no-sd; + no-sdio; non-removable; fixed-emmc-driver-type = <1>; full-pwr-cycle-in-suspend; diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi index 8f8d7371d8e2..a04eae55dd6c 100644 --- a/arch/arm64/boot/dts/renesas/ulcb.dtsi +++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi @@ -468,6 +468,8 @@ bus-width = <8>; mmc-hs200-1_8v; mmc-hs400-1_8v; + no-sd; + no-sdio; non-removable; full-pwr-cycle-in-suspend; status = "okay"; From 34c0e3e1111bf036d3ffc5f183afc1fff05050e5 Mon Sep 17 00:00:00 2001 From: Koji Matsuoka Date: Thu, 21 Jan 2021 10:54:18 +0100 Subject: [PATCH 312/584] arm64: dts: renesas: r8a779a0: Add I2C nodes Add I2C devicetree description to V3U Signed-off-by: Koji Matsuoka [wsa: rebased and double checked] Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121095420.5023-3-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 122 ++++++++++++++++++++++ 1 file changed, 122 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 25c722302de6..1d953a892309 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -14,6 +14,16 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + i2c6 = &i2c6; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -250,6 +260,118 @@ #power-domain-cells = <1>; }; + i2c0: i2c@e6500000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe6500000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 518>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 518>; + dmas = <&dmac1 0x91>, <&dmac1 0x90>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@e6508000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe6508000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 519>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 519>; + dmas = <&dmac1 0x93>, <&dmac1 0x92>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@e6510000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe6510000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 520>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 520>; + dmas = <&dmac1 0x95>, <&dmac1 0x94>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@e66d0000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66d0000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 521>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 521>; + dmas = <&dmac1 0x97>, <&dmac1 0x96>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@e66d8000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66d8000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 522>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 522>; + dmas = <&dmac1 0x99>, <&dmac1 0x98>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@e66e0000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66e0000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 523>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 523>; + dmas = <&dmac1 0x9b>, <&dmac1 0x9a>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@e66e8000 { + compatible = "renesas,i2c-r8a779a0", + "renesas,rcar-gen3-i2c"; + reg = <0 0xe66e8000 0 0x40>; + interrupts = ; + clocks = <&cpg CPG_MOD 524>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 524>; + dmas = <&dmac1 0x9d>, <&dmac1 0x9c>; + dma-names = "tx", "rx"; + i2c-scl-internal-delay-ns = <110>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + scif0: serial@e6e60000 { compatible = "renesas,scif-r8a779a0", "renesas,rcar-gen3-scif", "renesas,scif"; From 0e6fb83ef258a9abf5b96c51722765e8ccfca9fe Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Thu, 21 Jan 2021 10:54:19 +0100 Subject: [PATCH 313/584] arm64: dts: renesas: falcon: Add I2C0,1,6 support Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121095420.5023-4-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- .../boot/dts/renesas/r8a779a0-falcon-cpu.dtsi | 41 +++++++++++++++++++ 1 file changed, 41 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi index 4ba269a4cec8..90aa1395a49f 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi @@ -41,6 +41,47 @@ clock-frequency = <32768>; }; +&i2c0 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + +&i2c1 { + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + +&i2c6 { + pinctrl-0 = <&i2c6_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; +}; + +&pfc { + i2c0_pins: i2c0 { + groups = "i2c0"; + function = "i2c0"; + }; + + i2c1_pins: i2c1 { + groups = "i2c1"; + function = "i2c1"; + }; + + i2c6_pins: i2c6 { + groups = "i2c6"; + function = "i2c6"; + }; +}; + &scif0 { status = "okay"; }; From 5a633320f08b8c9bccc37f100b3b26202f158dac Mon Sep 17 00:00:00 2001 From: Tho Vu Date: Thu, 21 Jan 2021 11:06:17 +0100 Subject: [PATCH 314/584] arm64: dts: renesas: r8a779a0: Add Ethernet-AVB support Define the generic parts of Ethernet-AVB device nodes. Only AVB0 was tested because it was the only port with a PHY on current hardware. Signed-off-by: Tho Vu [wsa: double checked, rebased, added "internal-delay" properties] Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121100619.5653-4-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 282 ++++++++++++++++++++++ 1 file changed, 282 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 1d953a892309..4671a5840ae1 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -372,6 +372,288 @@ status = "disabled"; }; + avb0: ethernet@e6800000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6800000 0 0x800>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 211>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 211>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb1: ethernet@e6810000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6810000 0 0x800>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 212>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 212>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb2: ethernet@e6820000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6820000 0 0x1000>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 213>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 213>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb3: ethernet@e6830000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6830000 0 0x1000>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 214>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 214>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb4: ethernet@e6840000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6840000 0 0x1000>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 215>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 215>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + avb5: ethernet@e6850000 { + compatible = "renesas,etheravb-r8a779a0", + "renesas,etheravb-rcar-gen3"; + reg = <0 0xe6850000 0 0x1000>; + interrupts = , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + , + ; + interrupt-names = "ch0", "ch1", "ch2", "ch3", + "ch4", "ch5", "ch6", "ch7", + "ch8", "ch9", "ch10", "ch11", + "ch12", "ch13", "ch14", "ch15", + "ch16", "ch17", "ch18", "ch19", + "ch20", "ch21", "ch22", "ch23", + "ch24"; + clocks = <&cpg CPG_MOD 216>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 216>; + phy-mode = "rgmii"; + rx-internal-delay-ps = <0>; + tx-internal-delay-ps = <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + scif0: serial@e6e60000 { compatible = "renesas,scif-r8a779a0", "renesas,rcar-gen3-scif", "renesas,scif"; From e8ac55a5e70a952247f7b0a5bd234536a9e099ad Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Thu, 21 Jan 2021 11:06:18 +0100 Subject: [PATCH 315/584] arm64: dts: renesas: falcon: Add Ethernet-AVB0 support Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121100619.5653-5-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- .../boot/dts/renesas/r8a779a0-falcon-cpu.dtsi | 35 +++++++++++++++++++ .../boot/dts/renesas/r8a779a0-falcon.dts | 1 + 2 files changed, 36 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi index 90aa1395a49f..597676ee4deb 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi @@ -5,6 +5,7 @@ * Copyright (C) 2020 Renesas Electronics Corp. */ +#include #include "r8a779a0.dtsi" / { @@ -33,6 +34,22 @@ }; }; +&avb0 { + pinctrl-0 = <&avb0_pins>; + pinctrl-names = "default"; + phy-handle = <&phy0>; + tx-internal-delay-ps = <2000>; + status = "okay"; + + phy0: ethernet-phy@0 { + rxc-skew-ps = <1500>; + reg = <0>; + interrupt-parent = <&gpio4>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>; + }; +}; + &extal_clk { clock-frequency = <16666666>; }; @@ -66,6 +83,24 @@ }; &pfc { + avb0_pins: avb0 { + mux { + groups = "avb0_link", "avb0_mdio", "avb0_rgmii", "avb0_txcrefclk"; + function = "avb0"; + }; + + pins_mdio { + groups = "avb0_mdio"; + drive-strength = <21>; + }; + + pins_mii { + groups = "avb0_rgmii"; + drive-strength = <21>; + }; + + }; + i2c0_pins: i2c0 { groups = "i2c0"; function = "i2c0"; diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts index fb9978ea18f4..5617b81dd7dc 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts @@ -13,6 +13,7 @@ compatible = "renesas,falcon-breakout", "renesas,falcon-cpu", "renesas,r8a779a0"; aliases { + ethernet0 = &avb0; serial0 = &scif0; }; From bff4e5dac9992ba5a6b2d318570b993f4c616b5c Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Thu, 21 Jan 2021 12:00:05 +0100 Subject: [PATCH 316/584] arm64: dts: renesas: r8a779a0: Add & update SCIF nodes This is the result of multiple patches taken from the BSP, combined, rebased, and properly sorted. SCIF0 gets DMA properties, other SCIFs are entirely new. Signed-off-by: Linh Phung Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121110008.15894-2-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 50 +++++++++++++++++++++++ 1 file changed, 50 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 4671a5840ae1..2a6d0e8b5bcb 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -663,11 +663,61 @@ <&cpg CPG_CORE R8A779A0_CLK_S1D2>, <&scif_clk>; clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x51>, <&dmac1 0x50>; + dma-names = "tx", "rx"; power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; resets = <&cpg 702>; status = "disabled"; }; + scif1: serial@e6e68000 { + compatible = "renesas,scif-r8a779a0", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6e68000 0 64>; + interrupts = ; + clocks = <&cpg CPG_MOD 703>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x53>, <&dmac1 0x52>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 703>; + status = "disabled"; + }; + + scif3: serial@e6c50000 { + compatible = "renesas,scif-r8a779a0", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6c50000 0 64>; + interrupts = ; + clocks = <&cpg CPG_MOD 704>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x57>, <&dmac1 0x56>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 704>; + status = "disabled"; + }; + + scif4: serial@e6c40000 { + compatible = "renesas,scif-r8a779a0", + "renesas,rcar-gen3-scif", "renesas,scif"; + reg = <0 0xe6c40000 0 64>; + interrupts = ; + clocks = <&cpg CPG_MOD 705>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x59>, <&dmac1 0x58>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 705>; + status = "disabled"; + }; + msiof0: spi@e6e90000 { compatible = "renesas,msiof-r8a779a0", "renesas,rcar-gen3-msiof"; From 9e921faa305369e5cbe4fd8f3212a1ad6aa85c79 Mon Sep 17 00:00:00 2001 From: Wolfram Sang Date: Thu, 21 Jan 2021 12:00:06 +0100 Subject: [PATCH 317/584] arm64: dts: renesas: falcon: Complete SCIF0 nodes SCIF0 has been enabled by the firmware, so it worked already. Still, add the proper nodes to make it work in any case. Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121110008.15894-3-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- .../boot/dts/renesas/r8a779a0-falcon-cpu.dtsi | 21 +++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi index 597676ee4deb..c0df0e7f32b8 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi @@ -83,6 +83,9 @@ }; &pfc { + pinctrl-0 = <&scif_clk_pins>; + pinctrl-names = "default"; + avb0_pins: avb0 { mux { groups = "avb0_link", "avb0_mdio", "avb0_rgmii", "avb0_txcrefclk"; @@ -115,8 +118,26 @@ groups = "i2c6"; function = "i2c6"; }; + + scif0_pins: scif0 { + groups = "scif0_data", "scif0_ctrl"; + function = "scif0"; + }; + + scif_clk_pins: scif_clk { + groups = "scif_clk"; + function = "scif_clk"; + }; }; &scif0 { + pinctrl-0 = <&scif0_pins>; + pinctrl-names = "default"; + + uart-has-rtscts; status = "okay"; }; + +&scif_clk { + clock-frequency = <24000000>; +}; From 088e6b23050487cae1bd7f70b439a453689b6f53 Mon Sep 17 00:00:00 2001 From: Linh Phung Date: Thu, 21 Jan 2021 12:00:07 +0100 Subject: [PATCH 318/584] arm64: dts: renesas: r8a779a0: Add HSCIF support Define the generic parts of the HSCIF[0-3] device nodes. Signed-off-by: Linh Phung Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210121110008.15894-4-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 64 +++++++++++++++++++++++ 1 file changed, 64 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 2a6d0e8b5bcb..138cf07e46f0 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -372,6 +372,70 @@ status = "disabled"; }; + hscif0: serial@e6540000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe6540000 0 0x60>; + interrupts = ; + clocks = <&cpg CPG_MOD 514>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x31>, <&dmac1 0x30>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 514>; + status = "disabled"; + }; + + hscif1: serial@e6550000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe6550000 0 0x60>; + interrupts = ; + clocks = <&cpg CPG_MOD 515>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x33>, <&dmac1 0x32>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 515>; + status = "disabled"; + }; + + hscif2: serial@e6560000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe6560000 0 0x60>; + interrupts = ; + clocks = <&cpg CPG_MOD 516>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x35>, <&dmac1 0x34>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 516>; + status = "disabled"; + }; + + hscif3: serial@e66a0000 { + compatible = "renesas,hscif-r8a779a0", + "renesas,rcar-gen3-hscif", "renesas,hscif"; + reg = <0 0xe66a0000 0 0x60>; + interrupts = ; + clocks = <&cpg CPG_MOD 517>, + <&cpg CPG_CORE R8A779A0_CLK_S1D2>, + <&scif_clk>; + clock-names = "fck", "brg_int", "scif_clk"; + dmas = <&dmac1 0x37>, <&dmac1 0x36>; + dma-names = "tx", "rx"; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 517>; + status = "disabled"; + }; + avb0: ethernet@e6800000 { compatible = "renesas,etheravb-r8a779a0", "renesas,etheravb-rcar-gen3"; From 6b159d547d462f4e47f1ae913f0c05e7071183ec Mon Sep 17 00:00:00 2001 From: Takeshi Saito Date: Mon, 25 Jan 2021 08:58:44 +0100 Subject: [PATCH 319/584] arm64: dts: renesas: r8a779a0: Add MMC node Add a device node for MMC. Signed-off-by: Takeshi Saito Signed-off-by: Koji Matsuoka [wsa: double checked & rebased] Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210125075845.3864-2-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- arch/arm64/boot/dts/renesas/r8a779a0.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi index 138cf07e46f0..dfd6ae8b564f 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi @@ -930,6 +930,18 @@ dma-channels = <8>; }; + mmc0: mmc@ee140000 { + compatible = "renesas,sdhi-r8a779a0", + "renesas,rcar-gen3-sdhi"; + reg = <0 0xee140000 0 0x2000>; + interrupts = ; + clocks = <&cpg CPG_MOD 706>; + power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>; + resets = <&cpg 706>; + max-frequency = <200000000>; + status = "disabled"; + }; + gic: interrupt-controller@f1000000 { compatible = "arm,gic-v3"; #interrupt-cells = <3>; From ee33cd69344ff04f3b512eb9d74c16c412b07115 Mon Sep 17 00:00:00 2001 From: Takeshi Saito Date: Mon, 25 Jan 2021 08:58:45 +0100 Subject: [PATCH 320/584] arm64: dts: renesas: falcon: Enable MMC Enable MMC on the Falcon board. Signed-off-by: Takeshi Saito Signed-off-by: Koji Matsuoka [wsa: double checked, rebased, slightly improved, moved to falcon-cpu] Signed-off-by: Wolfram Sang Link: https://lore.kernel.org/r/20210125075845.3864-3-wsa+renesas@sang-engineering.com Signed-off-by: Geert Uytterhoeven --- .../boot/dts/renesas/r8a779a0-falcon-cpu.dtsi | 41 +++++++++++++++++++ 1 file changed, 41 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi index c0df0e7f32b8..fa284a7260d6 100644 --- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi +++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi @@ -32,6 +32,24 @@ device_type = "memory"; reg = <0x7 0x00000000 0x0 0x80000000>; }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; }; &avb0 { @@ -82,6 +100,23 @@ clock-frequency = <400000>; }; +&mmc0 { + pinctrl-0 = <&mmc_pins>; + pinctrl-1 = <&mmc_pins>; + pinctrl-names = "default", "state_uhs"; + + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + full-pwr-cycle-in-suspend; + status = "okay"; +}; + &pfc { pinctrl-0 = <&scif_clk_pins>; pinctrl-names = "default"; @@ -119,6 +154,12 @@ function = "i2c6"; }; + mmc_pins: mmc { + groups = "mmc_data8", "mmc_ctrl", "mmc_ds"; + function = "mmc"; + power-source = <1800>; + }; + scif0_pins: scif0 { groups = "scif0_data", "scif0_ctrl"; function = "scif0"; From 1769b7f92a85b9841d59dc358eb968cba705d9a8 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Sun, 24 Jan 2021 18:02:57 +0100 Subject: [PATCH 321/584] ARM: dts: stm32: Add additional init state for SDMMC1 pins Add "init" mux option for SDMMC1, where the CMD, CK, CKIN lines are not configured, so they can be claimed as GPIOs early on in driver probe(). This is used for probing optional voltage level translator. Signed-off-by: Marek Vasut Cc: Alexandre Torgue Cc: Linus Walleij Cc: Ludovic Barre Cc: Ulf Hansson Cc: linux-stm32@st-md-mailman.stormreply.com Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi index 20a59e8f7a33..53326ed652f8 100644 --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi @@ -1273,6 +1273,18 @@ }; }; + sdmmc1_b4_init_pins_a: sdmmc1-b4-init-0 { + pins1 { + pinmux = , /* SDMMC1_D0 */ + , /* SDMMC1_D1 */ + , /* SDMMC1_D2 */ + ; /* SDMMC1_D3 */ + slew-rate = <1>; + drive-push-pull; + bias-disable; + }; + }; + sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 { pins { pinmux = , /* SDMMC1_D0 */ @@ -1299,6 +1311,17 @@ }; }; + sdmmc1_dir_init_pins_a: sdmmc1-dir-init-0 { + pins1 { + pinmux = , /* SDMMC1_D0DIR */ + , /* SDMMC1_D123DIR */ + ; /* SDMMC1_CDIR */ + slew-rate = <1>; + drive-push-pull; + bias-pull-up; + }; + }; + sdmmc1_dir_sleep_pins_a: sdmmc1-dir-sleep-0 { pins { pinmux = , /* SDMMC1_D0DIR */ From c6499becd72b34cf1d9b5b15a56b2d17f6107efd Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Sun, 24 Jan 2021 18:02:58 +0100 Subject: [PATCH 322/584] ARM: dts: stm32: Enable voltage translator auto-detection on DHCOM The DHCOM SoM uSD slot has an optional voltage level translator, add DT bindings which permit the MMCI driver to detect the translator automatically. Signed-off-by: Marek Vasut Cc: Alexandre Torgue Cc: Linus Walleij Cc: Ludovic Barre Cc: Ulf Hansson Cc: linux-stm32@st-md-mailman.stormreply.com Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi index 2a20818c91e4..2617815e42a6 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi @@ -386,14 +386,19 @@ }; &sdmmc1 { - pinctrl-names = "default", "opendrain", "sleep"; + pinctrl-names = "default", "opendrain", "sleep", "init"; pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>; pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_dir_pins_a>; pinctrl-2 = <&sdmmc1_b4_sleep_pins_a &sdmmc1_dir_sleep_pins_a>; + pinctrl-3 = <&sdmmc1_b4_init_pins_a &sdmmc1_dir_init_pins_a>; cd-gpios = <&gpiog 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; disable-wp; st,sig-dir; st,neg-edge; + st,use-ckin; + st,cmd-gpios = <&gpiod 2 0>; + st,ck-gpios = <&gpioc 12 0>; + st,ckin-gpios = <&gpioe 4 0>; bus-width = <4>; vmmc-supply = <&vdd_sd>; status = "okay"; From 5562255b68f557df6412ab57df2cd6b4e8b653b4 Mon Sep 17 00:00:00 2001 From: Marek Vasut Date: Sun, 24 Jan 2021 18:03:37 +0100 Subject: [PATCH 323/584] ARM: dts: stm32: Rename mmc controller nodes to mmc@ Per mmc-controller.yaml, the node pattern is "^mmc(@.*)?$" , so adjust the node. Signed-off-by: Marek Vasut Cc: Alexandre Torgue Cc: Ludovic Barre Cc: Ulf Hansson Cc: linux-stm32@st-md-mailman.stormreply.com Cc: devicetree@vger.kernel.org Acked-by: Yann Gautier Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32f429.dtsi | 2 +- arch/arm/boot/dts/stm32f746.dtsi | 4 ++-- arch/arm/boot/dts/stm32h743.dtsi | 2 +- arch/arm/boot/dts/stm32mp151.dtsi | 6 +++--- 4 files changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi index ad715a0e1c9a..f6530d724d00 100644 --- a/arch/arm/boot/dts/stm32f429.dtsi +++ b/arch/arm/boot/dts/stm32f429.dtsi @@ -566,7 +566,7 @@ }; }; - sdio: sdio@40012c00 { + sdio: mmc@40012c00 { compatible = "arm,pl180", "arm,primecell"; arm,primecell-periphid = <0x00880180>; reg = <0x40012c00 0x400>; diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi index 640ff54ed00c..e1df603fc981 100644 --- a/arch/arm/boot/dts/stm32f746.dtsi +++ b/arch/arm/boot/dts/stm32f746.dtsi @@ -473,7 +473,7 @@ status = "disabled"; }; - sdio2: sdio2@40011c00 { + sdio2: mmc@40011c00 { compatible = "arm,pl180", "arm,primecell"; arm,primecell-periphid = <0x00880180>; reg = <0x40011c00 0x400>; @@ -484,7 +484,7 @@ status = "disabled"; }; - sdio1: sdio1@40012c00 { + sdio1: mmc@40012c00 { compatible = "arm,pl180", "arm,primecell"; arm,primecell-periphid = <0x00880180>; reg = <0x40012c00 0x400>; diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi index b083afd0ebd6..4ebffb0a45a3 100644 --- a/arch/arm/boot/dts/stm32h743.dtsi +++ b/arch/arm/boot/dts/stm32h743.dtsi @@ -354,7 +354,7 @@ dma-requests = <32>; }; - sdmmc1: sdmmc@52007000 { + sdmmc1: mmc@52007000 { compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x10153180>; reg = <0x52007000 0x1000>; diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi index 3c75abacb374..0d4db78ae255 100644 --- a/arch/arm/boot/dts/stm32mp151.dtsi +++ b/arch/arm/boot/dts/stm32mp151.dtsi @@ -1047,7 +1047,7 @@ }; }; - sdmmc3: sdmmc@48004000 { + sdmmc3: mmc@48004000 { compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x00253180>; reg = <0x48004000 0x400>; @@ -1368,7 +1368,7 @@ status = "disabled"; }; - sdmmc1: sdmmc@58005000 { + sdmmc1: mmc@58005000 { compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x00253180>; reg = <0x58005000 0x1000>; @@ -1383,7 +1383,7 @@ status = "disabled"; }; - sdmmc2: sdmmc@58007000 { + sdmmc2: mmc@58007000 { compatible = "arm,pl18x", "arm,primecell"; arm,primecell-periphid = <0x00253180>; reg = <0x58007000 0x1000>; From e14775aa2feac18e7378cb8009b55c13d4236b50 Mon Sep 17 00:00:00 2001 From: Robert Marko Date: Mon, 7 Sep 2020 12:19:37 +0200 Subject: [PATCH 324/584] ARM: dts: qcom: ipq4019: add SDHCI VQMMC LDO node Since we now have driver for the SDHCI VQMMC LDO needed for I/0 voltage levels lets introduce the necessary node for it. Signed-off-by: Robert Marko Cc: Luka Perkov Link: https://lore.kernel.org/r/20200907101937.10155-1-robert.marko@sartura.hr Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-ipq4019.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index 0ad6c242dc3e..7bf1da916f25 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -209,6 +209,16 @@ interrupts = ; }; + vqmmc: regulator@1948000 { + compatible = "qcom,vqmmc-ipq4019-regulator"; + reg = <0x01948000 0x4>; + regulator-name = "vqmmc"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + status = "disabled"; + }; + sdhci: sdhci@7824900 { compatible = "qcom,sdhci-msm-v4"; reg = <0x7824900 0x11c>, <0x7824000 0x800>; From e9ced25e41588a2ff95280b4d3dabf3a0865513b Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Mon, 21 Dec 2020 19:13:02 +0100 Subject: [PATCH 325/584] ARM: dts: meson: move iio-hwmon for the SoC temperature to meson.dtsi The SoC temperature can be retrieved from ADC channel 8 on all 32-bit SoCs (Meson6, Meson8, Meson8b and Meson8m2). Move the iio-hwmon instance to meson.dtsi instead of duplicating it in all board.dts. If the temperature sensor calibration data is missing for a board then iio-hwmon will simply not probe. Signed-off-by: Martin Blumenstingl Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20201221181306.904272-2-martin.blumenstingl@googlemail.com --- arch/arm/boot/dts/meson.dtsi | 5 +++++ arch/arm/boot/dts/meson8b-ec100.dts | 5 ----- arch/arm/boot/dts/meson8b-mxq.dts | 5 ----- arch/arm/boot/dts/meson8b-odroidc1.dts | 5 ----- arch/arm/boot/dts/meson8m2-mxiii-plus.dts | 5 ----- 5 files changed, 5 insertions(+), 20 deletions(-) diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi index 7649dd1e0b9e..5f074f7aa1a2 100644 --- a/arch/arm/boot/dts/meson.dtsi +++ b/arch/arm/boot/dts/meson.dtsi @@ -11,6 +11,11 @@ #size-cells = <1>; interrupt-parent = <&gic>; + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&saradc 8>; + }; + soc { compatible = "simple-bus"; #address-cells = <1>; diff --git a/arch/arm/boot/dts/meson8b-ec100.dts b/arch/arm/boot/dts/meson8b-ec100.dts index ed06102a4014..8e48ccc6b634 100644 --- a/arch/arm/boot/dts/meson8b-ec100.dts +++ b/arch/arm/boot/dts/meson8b-ec100.dts @@ -70,11 +70,6 @@ timeout-ms = <20000>; }; - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&saradc 8>; - }; - leds { compatible = "gpio-leds"; diff --git a/arch/arm/boot/dts/meson8b-mxq.dts b/arch/arm/boot/dts/meson8b-mxq.dts index 33037ef62d0a..f3937d55472d 100644 --- a/arch/arm/boot/dts/meson8b-mxq.dts +++ b/arch/arm/boot/dts/meson8b-mxq.dts @@ -27,11 +27,6 @@ reg = <0x40000000 0x40000000>; }; - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&saradc 8>; - }; - vcck: regulator-vcck { compatible = "pwm-regulator"; diff --git a/arch/arm/boot/dts/meson8b-odroidc1.dts b/arch/arm/boot/dts/meson8b-odroidc1.dts index 5963566dbcc9..c440ef94e082 100644 --- a/arch/arm/boot/dts/meson8b-odroidc1.dts +++ b/arch/arm/boot/dts/meson8b-odroidc1.dts @@ -85,11 +85,6 @@ 1800000 1>; }; - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&saradc 8>; - }; - rtc32k_xtal: rtc32k-xtal-clk { /* X3 in the schematics */ compatible = "fixed-clock"; diff --git a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts index 8f4eb1ed4581..fa6d55f1cfb9 100644 --- a/arch/arm/boot/dts/meson8m2-mxiii-plus.dts +++ b/arch/arm/boot/dts/meson8m2-mxiii-plus.dts @@ -45,11 +45,6 @@ }; }; - iio-hwmon { - compatible = "iio-hwmon"; - io-channels = <&saradc 8>; - }; - vcc_3v3: regulator-vcc3v3 { compatible = "regulator-fixed"; regulator-name = "VCC3V3"; From c8559511107120403f7810428f50fc68fd77ed5a Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Mon, 21 Dec 2020 19:13:03 +0100 Subject: [PATCH 326/584] ARM: dts: meson: add the ADC thermal sensor to meson.dtsi The SoC temperature can be retrieved from ADC channel 8 on all 32-bit SoCs (Meson6, Meson8, Meson8b and Meson8m2). Add a "generic-adc-thermal" instance to meson.dtsi so the thermal sensor is available for all SoCs. If the temperature sensor calibration data is missing for a board then the "generic-adc-thermal" will not probe and not register a thermal sensor. Signed-off-by: Martin Blumenstingl Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20201221181306.904272-3-martin.blumenstingl@googlemail.com --- arch/arm/boot/dts/meson.dtsi | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi index 5f074f7aa1a2..e0ca5f08d07d 100644 --- a/arch/arm/boot/dts/meson.dtsi +++ b/arch/arm/boot/dts/meson.dtsi @@ -298,6 +298,13 @@ }; }; + thermal_sensor: thermal-sensor { + compatible = "generic-adc-thermal"; + #thermal-sensor-cells = <0>; + io-channels = <&saradc 8>; + io-channel-names = "sensor-channel"; + }; + xtal: xtal-clk { compatible = "fixed-clock"; clock-frequency = <24000000>; From ecdb744b1f819949f783508331ff6ff8a6a45730 Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Mon, 21 Dec 2020 19:13:04 +0100 Subject: [PATCH 327/584] ARM: dts: meson8: add the thermal-zones with cooling configuration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The vendor kernel uses the following thermal-zone settings: <= 70°C: - CPU frequency limited to 1.608GHz - GPU limited to 511MHz and 5 cores (pixel processors) <= 80°C: - CPU frequency limited to 1.2GHz - GPU limited to 435MHz and 4 cores (pixel processors) <= 90°C: - CPU frequency limited to 0.804GHz - GPU limited to 328MHz and 3 cores (pixel processors) Add simplified thermal configuration which is taken from the GXBB/GXL/GXM SoC family (which uses the same manufacturing process and has the same maximum junction temperature of 125°C). With this the thermal framework will try to keep the SoC temperature at or below 80°C which is identical to the vendor kernel (with the exception of one GPU pixel processor). The number of GPU cores are not taken into account as this is not supported. Signed-off-by: Martin Blumenstingl Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20201221181306.904272-4-martin.blumenstingl@googlemail.com --- arch/arm/boot/dts/meson8.dtsi | 54 +++++++++++++++++++++++++++++++++++ 1 file changed, 54 insertions(+) diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi index 04688e8abce2..420324ea2ad7 100644 --- a/arch/arm/boot/dts/meson8.dtsi +++ b/arch/arm/boot/dts/meson8.dtsi @@ -9,6 +9,7 @@ #include #include #include +#include #include "meson.dtsi" / { @@ -28,6 +29,7 @@ resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; cpu1: cpu@201 { @@ -39,6 +41,7 @@ resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; cpu2: cpu@202 { @@ -50,6 +53,7 @@ resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; cpu3: cpu@203 { @@ -61,6 +65,7 @@ resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; }; @@ -190,6 +195,54 @@ }; }; + thermal-zones { + soc { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + thermal-sensors = <&thermal_sensor>; + + cooling-maps { + map0 { + trip = <&soc_passive>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + + map1 { + trip = <&soc_hot>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + soc_passive: soc-passive { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + soc_hot: soc-hot { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "hot"; + }; + + soc_critical: soc-critical { + temperature = <110000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + }; + }; + mmcbus: bus@c8000000 { compatible = "simple-bus"; reg = <0xc8000000 0x8000>; @@ -254,6 +307,7 @@ clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>; clock-names = "bus", "core"; operating-points-v2 = <&gpu_opp_table>; + #cooling-cells = <2>; /* min followed by max */ }; }; }; /* end of / */ From 9073f694efd8733b0e7c97d3396d81161bd05582 Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Mon, 21 Dec 2020 19:13:05 +0100 Subject: [PATCH 328/584] ARM: dts: meson8b: add the thermal-zones with cooling configuration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The vendor kernel uses the following thermal-zone settings: <= 70°C: - CPU frequency limited to 1.488GHz - GPU limited to 511MHz and 2 cores (pixel processors) <= 80°C: - CPU frequency limited to 1.2GHz - GPU limited to 435MHz and 2 cores (pixel processors) <= 90°C: - CPU frequency limited to 0.804GHz - GPU limited to 328MHz and 1 core (pixel processor) Add simplified thermal configuration which is taken from the GXBB/GXL/GXM SoC family (which uses the same manufacturing process and has the same maximum junction temperature of 125°C). With this the thermal framework will try to keep the SoC temperature at or below 80°C which is identical to the vendor kernel (with the exception of one CPU frequency step from 1.488GHz to 1.536GHz). The number of GPU cores are not taken into account as this is not supported. Signed-off-by: Martin Blumenstingl Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20201221181306.904272-5-martin.blumenstingl@googlemail.com --- arch/arm/boot/dts/meson8b.dtsi | 54 ++++++++++++++++++++++++++++++++++ 1 file changed, 54 insertions(+) diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi index 2401cdf5f751..dbf7963b6c87 100644 --- a/arch/arm/boot/dts/meson8b.dtsi +++ b/arch/arm/boot/dts/meson8b.dtsi @@ -10,6 +10,7 @@ #include #include #include +#include #include "meson.dtsi" / { @@ -26,6 +27,7 @@ resets = <&clkc CLKC_RESET_CPU0_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; cpu1: cpu@201 { @@ -37,6 +39,7 @@ resets = <&clkc CLKC_RESET_CPU1_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; cpu2: cpu@202 { @@ -48,6 +51,7 @@ resets = <&clkc CLKC_RESET_CPU2_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; cpu3: cpu@203 { @@ -59,6 +63,7 @@ resets = <&clkc CLKC_RESET_CPU3_SOFT_RESET>; operating-points-v2 = <&cpu_opp_table>; clocks = <&clkc CLKID_CPUCLK>; + #cooling-cells = <2>; /* min followed by max */ }; }; @@ -167,6 +172,54 @@ }; }; + thermal-zones { + soc { + polling-delay-passive = <250>; /* milliseconds */ + polling-delay = <1000>; /* milliseconds */ + thermal-sensors = <&thermal_sensor>; + + cooling-maps { + map0 { + trip = <&soc_passive>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + + map1 { + trip = <&soc_hot>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + soc_passive: soc-passive { + temperature = <80000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "passive"; + }; + + soc_hot: soc-hot { + temperature = <90000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "hot"; + }; + + soc_critical: soc-critical { + temperature = <110000>; /* millicelsius */ + hysteresis = <2000>; /* millicelsius */ + type = "critical"; + }; + }; + }; + }; + mmcbus: bus@c8000000 { compatible = "simple-bus"; reg = <0xc8000000 0x8000>; @@ -221,6 +274,7 @@ clocks = <&clkc CLKID_CLK81>, <&clkc CLKID_MALI>; clock-names = "bus", "core"; operating-points-v2 = <&gpu_opp_table>; + #cooling-cells = <2>; /* min followed by max */ }; }; }; /* end of / */ From 0f7273c3daff285e581cb30f8dad9d086ea201b7 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:19:42 +0100 Subject: [PATCH 329/584] arm64: dts: qcom: msm8992/4: Add RPM Power Domains Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118161943.105733-2-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8992.dtsi | 30 +++++++++++++++++++++++++++ arch/arm64/boot/dts/qcom/msm8994.dtsi | 30 +++++++++++++++++++++++++++ 2 files changed, 60 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi index 0c422af47917..c33b40db0f49 100644 --- a/arch/arm64/boot/dts/qcom/msm8992.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi @@ -4,6 +4,7 @@ #include #include +#include / { interrupt-parent = <&intc>; @@ -713,6 +714,35 @@ compatible = "qcom,rpmcc-msm8992"; #clock-cells = <1>; }; + + rpmpd: power-controller { + compatible = "qcom,msm8994-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_ret: opp1 { + opp-level = <1>; + }; + rpmpd_opp_svs_krait: opp2 { + opp-level = <2>; + }; + rpmpd_opp_svs_soc: opp3 { + opp-level = <3>; + }; + rpmpd_opp_nom: opp4 { + opp-level = <4>; + }; + rpmpd_opp_turbo: opp5 { + opp-level = <5>; + }; + rpmpd_opp_super_turbo: opp6 { + opp-level = <6>; + }; + }; + }; }; }; }; diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index 6e083a2f690b..9755780b53d7 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -4,6 +4,7 @@ #include #include +#include / { interrupt-parent = <&intc>; @@ -192,6 +193,35 @@ compatible = "qcom,rpmcc-msm8994"; #clock-cells = <1>; }; + + rpmpd: power-controller { + compatible = "qcom,msm8994-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_ret: opp1 { + opp-level = <1>; + }; + rpmpd_opp_svs_krait: opp2 { + opp-level = <2>; + }; + rpmpd_opp_svs_soc: opp3 { + opp-level = <3>; + }; + rpmpd_opp_nom: opp4 { + opp-level = <4>; + }; + rpmpd_opp_turbo: opp5 { + opp-level = <5>; + }; + rpmpd_opp_super_turbo: opp6 { + opp-level = <6>; + }; + }; + }; }; }; }; From 72b312411de71887c3c0076017455d911b92bb18 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:21 +0100 Subject: [PATCH 330/584] arm64: dts: qcom: Add support for remaining Sony Kitakami boards This patch adds support for the following Xperias: * Z3+ [aka Z4 in some regions] (Ivy) * Z4 Tablet (Karin) * Z4 Tablet Wi-Fi (Karin_windy) [APQ8094] * Z5 Compact (Suzuran) * Z5 Premium (Satsuki) These devices are very similar in terms of hardware, with main differences being display panels. While at it, update comments describing hardware used: SMB charger seems to not be used after all, PMI8994 charger is in use instead. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-1-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 5 +++++ ...q8094-sony-xperia-kitakami-karin_windy.dts | 20 ++++++++++++++++++ .../qcom/msm8994-sony-xperia-kitakami-ivy.dts | 13 ++++++++++++ .../msm8994-sony-xperia-kitakami-karin.dts | 21 +++++++++++++++++++ .../msm8994-sony-xperia-kitakami-satsuki.dts | 13 ++++++++++++ .../msm8994-sony-xperia-kitakami-suzuran.dts | 13 ++++++++++++ .../qcom/msm8994-sony-xperia-kitakami.dtsi | 15 ++++++++++--- 7 files changed, 97 insertions(+), 3 deletions(-) create mode 100644 arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index b5d86739f781..59455db7b493 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -1,5 +1,6 @@ # SPDX-License-Identifier: GPL-2.0 dtb-$(CONFIG_ARCH_QCOM) += apq8016-sbc.dtb +dtb-$(CONFIG_ARCH_QCOM) += apq8094-sony-xperia-kitakami-karin_windy.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb @@ -14,7 +15,11 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-talkman.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-xiaomi-libra.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-msft-lumia-cityman.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-ivy.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-karin.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-satsuki.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-sumire.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-suzuran.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-asus-novago-tp370ql.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-hp-envy-x2.dtb diff --git a/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts new file mode 100644 index 000000000000..60497457a555 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + */ + +/dts-v1/; + +/* As the names may imply, there is quite a bunch of duplication there. */ +#include "msm8994-sony-xperia-kitakami-karin.dts" + +/ { + model = "Sony Xperia Z4 Tablet (Wi-Fi)"; + compatible = "sony,karin_windy", "qcom,apq8094"; + + /* + * This model uses the APQ variant of MSM8994 (APQ8094). + * The v1/v2/v2.1 story (from kitakami.dtsi) also applies here. + */ + qcom,msm-id = <253 0x20000>, <253 0x20001>; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts new file mode 100644 index 000000000000..4c7a90987f08 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z3+/Z4"; + compatible = "sony,ivy-row", "qcom,msm8994"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts new file mode 100644 index 000000000000..7e657861387b --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts @@ -0,0 +1,21 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z4 Tablet (LTE)"; + compatible = "sony,karin-row", "qcom,msm8994"; +}; + +&blsp_i2c5 { + /* + * TI LP8557 backlight driver @ 2c + * AD AD7146 touch controller @ 2f + * sii8620 HDMI/MHL bridge @ 72 (kitakami-common) + */ +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts new file mode 100644 index 000000000000..1081fe6a4d67 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z5 Premium"; + compatible = "sony,satsuki-row", "qcom,msm8994"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts new file mode 100644 index 000000000000..2c670ab28613 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts @@ -0,0 +1,13 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + */ + +/dts-v1/; + +#include "msm8994-sony-xperia-kitakami.dtsi" + +/ { + model = "Sony Xperia Z5 Compact"; + compatible = "sony,suzuran-row", "qcom,msm8994"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 791f254ac3f8..71d7187eb090 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -11,8 +11,17 @@ / { /* required for bootloader to select correct board */ - qcom,msm-id = <0xcf 0x20001>; + + /* + * We support MSM8994 v2 (0x20000) and v2.1 (0x20001). + * The V1 chip (0x0 and 0x10000) is significantly different + * and requires driver-side changes (including CPR, be warned!!). + * Besides that, it's very rare. + */ + qcom,msm-id = <207 0x20000>, <207 0x20001>; + /* We only use pm8994+pmi8994. */ qcom,pmic-id = <0x10009 0x1000a 0x00 0x00>; + /* This property is shared across all kitakami devices. */ qcom,board-id = <8 0>; /* Kitakami firmware doesn't support PSCI */ @@ -120,7 +129,7 @@ &blsp_i2c2 { status = "okay"; - /* NXP NFC */ + /* NXP PN547 NFC */ }; &blsp_i2c4 { @@ -132,7 +141,7 @@ &blsp_i2c5 { status = "okay"; - /* SMB1357 charger and sii8620 HDMI/MHL bridge */ + /* sii8620 HDMI/MHL bridge */ }; &blsp_i2c6 { From 1628dfe5f67ea8e9be005ece9a0bfdb75a05b214 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:22 +0100 Subject: [PATCH 331/584] arm64: dts: qcom: msm8992-bullhead: Update regulator config * Include pm(i)8994 dtsi * Add PMI8994 RPM regulators * Add comments concerning "missing" regulators Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-2-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8992-bullhead-rev-101.dts | 39 +++++++++++++------ 1 file changed, 27 insertions(+), 12 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts index 5969b5cfdc85..cacbfdbd69e3 100644 --- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts +++ b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts @@ -6,6 +6,8 @@ /dts-v1/; #include "msm8992.dtsi" +#include "pm8994.dtsi" +#include "pmi8994.dtsi" / { model = "LG Nexus 5X"; @@ -44,7 +46,7 @@ }; &rpm_requests { - pm8994-regulators { + pm8994_regulators: pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; vdd_l1-supply = <&pm8994_s1>; @@ -53,15 +55,17 @@ vdd_l4_27_31-supply = <&pm8994_s3>; vdd_l5_7-supply = <&pm8994_s3>; vdd_l6_12_32-supply = <&pm8994_s5>; - vdd_l8_16_30-supply = <&vreg_vph_pwr>; - vdd_l9_10_18_22-supply = <&vreg_vph_pwr>; - vdd_l13_19_23_24-supply = <&vreg_vph_pwr>; + vdd_l8_16_30-supply = <&vph_pwr>; + vdd_l9_10_18_22-supply = <&vph_pwr>; + vdd_l13_19_23_24-supply = <&vph_pwr>; vdd_l14_15-supply = <&pm8994_s5>; - vdd_l17_29-supply = <&vreg_vph_pwr>; - vdd_l20_21-supply = <&vreg_vph_pwr>; + vdd_l17_29-supply = <&vph_pwr>; + vdd_l20_21-supply = <&vph_pwr>; vdd_l25-supply = <&pm8994_s5>; vdd_lvs1_2 = <&pm8994_s4>; + /* S1, S2, S6 and S12 are managed by RPMPD */ + pm8994_s1: s1 { regulator-min-microvolt = <800000>; regulator-max-microvolt = <800000>; @@ -93,6 +97,8 @@ regulator-max-microvolt = <1000000>; }; + /* S8, S9, S10 and S11 - SPMI-managed VDD_APC */ + pm8994_l1: l1 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -113,18 +119,14 @@ regulator-max-microvolt = <1225000>; }; - pm8994_l5: l5 { - /* TODO */ - }; + /* L5 is inaccessible from RPM */ pm8994_l6: l6 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - pm8994_l7: l7 { - /* TODO */ - }; + /* L7 is inaccessible from RPM */ pm8994_l8: l8 { regulator-min-microvolt = <1800000>; @@ -266,6 +268,19 @@ */ }; }; + + pmi8994_regulators: pmi8994-regulators { + compatible = "qcom,rpm-pmi8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + pmi8994_s1: s1 {}; + + /* S2 & S3 - VDD_GFX */ + + pmi8994_bby: boost-bypass {}; + }; }; &sdhc_1 { From 31d9dbd2ae36a368e2e20ade76db16c6c489735f Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:23 +0100 Subject: [PATCH 332/584] arm64: dts: qcom: msm8992-libra: Update regulator config * Add PMI8994 RPM regulators * Add missing PM8994 LVSes * Add comments concerning "missing" regulators Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-3-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom/msm8992-xiaomi-libra.dts | 53 +++++++++++-------- 1 file changed, 31 insertions(+), 22 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts index 4f64ca3ea1ef..5dab8ee0c7d3 100644 --- a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts +++ b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts @@ -144,24 +144,16 @@ vdd_l4_27_31-supply = <&pm8994_s3>; vdd_l5_7-supply = <&pm8994_s3>; vdd_l6_12_32-supply = <&pm8994_s5>; - vdd_l8_16_30-supply = <&vreg_vph_pwr>; - vdd_l9_10_18_22-supply = <&vreg_vph_pwr>; - vdd_l13_19_23_24-supply = <&vreg_vph_pwr>; + vdd_l8_16_30-supply = <&vph_pwr>; + vdd_l9_10_18_22-supply = <&vph_pwr>; + vdd_l13_19_23_24-supply = <&vph_pwr>; vdd_l14_15-supply = <&pm8994_s5>; - vdd_l17_29-supply = <&vreg_vph_pwr>; - vdd_l20_21-supply = <&vreg_vph_pwr>; + vdd_l17_29-supply = <&vph_pwr>; + vdd_l20_21-supply = <&vph_pwr>; vdd_l25-supply = <&pm8994_s5>; vdd_lvs1_2 = <&pm8994_s4>; - pm8994_s1: s1 { - /* unused */ - status = "disabled"; - }; - - pm8994_s2: s2 { - /* unused */ - status = "disabled"; - }; + /* S1, S2, S6 and S12 are managed by RPMPD */ pm8994_s3: s3 { regulator-min-microvolt = <1300000>; @@ -186,6 +178,8 @@ regulator-max-microvolt = <1000000>; }; + /* S8, S9, S10 and S11 - SPMI-managed VDD_APC */ + pm8994_l1: l1 { regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; @@ -206,20 +200,14 @@ regulator-max-microvolt = <1225000>; }; - pm8994_l5: l5 { - /* unused */ - status = "disabled"; - }; + /* L5 is inaccessible from RPM */ pm8994_l6: l6 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; - pm8994_l7: l7 { - /* unused */ - status = "disabled"; - }; + /* L7 is inaccessible from RPM */ pm8994_l8: l8 { regulator-min-microvolt = <1800000>; @@ -352,6 +340,27 @@ regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; + + pm8994_lvs1: lvs1 {}; + pm8994_lvs2: lvs2 {}; + }; + + pmi8994_regulators: pmi8994-regulators { + compatible = "qcom,rpm-pmi8994-regulators"; + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + pmi8994_s1: s1 { + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + + /* S2 & S3 - VDD_GFX */ + + pmi8994_bby: boost-bypass { + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3600000>; + }; }; }; From 53364cfcaa7d20d9b066f546d0bee994310fc972 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:24 +0100 Subject: [PATCH 333/584] arm64: dts: qcom: msm8992/4: Rename vreg_vph_pwr to vph_pwr Rename the fixed regulator to follow the common naming scheme Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-4-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8992.dtsi | 5 ++--- arch/arm64/boot/dts/qcom/msm8994.dtsi | 4 ++-- 2 files changed, 4 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi index c33b40db0f49..b2046497dcaa 100644 --- a/arch/arm64/boot/dts/qcom/msm8992.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi @@ -755,10 +755,9 @@ ; }; - vreg_vph_pwr: vreg-vph-pwr { + vph_pwr: vph-pwr-regulator { compatible = "regulator-fixed"; - status = "okay"; - regulator-name = "vph-pwr"; + regulator-name = "vph_pwr"; regulator-min-microvolt = <3600000>; regulator-max-microvolt = <3600000>; diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index 9755780b53d7..2a6596406d9b 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -820,9 +820,9 @@ ; }; - vreg_vph_pwr: vreg-vph-pwr { + vph_pwr: vph-pwr-regulator { compatible = "regulator-fixed"; - regulator-name = "vph-pwr"; + regulator-name = "vph_pwr"; regulator-min-microvolt = <3600000>; regulator-max-microvolt = <3600000>; From 676b61b4790ad60512b35dbda8f9f6f83c5642dc Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:25 +0100 Subject: [PATCH 334/584] arm64: dts: qcom: msm/apq8994-kitakami: Add regulator config Add regulator config for all Kitakami devices, commonizing where applicable. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-5-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- ...q8094-sony-xperia-kitakami-karin_windy.dts | 3 + .../qcom/msm8994-sony-xperia-kitakami-ivy.dts | 13 + .../msm8994-sony-xperia-kitakami-karin.dts | 22 ++ .../msm8994-sony-xperia-kitakami-satsuki.dts | 5 + .../msm8994-sony-xperia-kitakami-sumire.dts | 2 + .../msm8994-sony-xperia-kitakami-suzuran.dts | 7 + .../qcom/msm8994-sony-xperia-kitakami.dtsi | 300 ++++++++++++++---- 7 files changed, 295 insertions(+), 57 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts index 60497457a555..a8dffc8c64ea 100644 --- a/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts +++ b/arch/arm64/boot/dts/qcom/apq8094-sony-xperia-kitakami-karin_windy.dts @@ -18,3 +18,6 @@ */ qcom,msm-id = <253 0x20000>, <253 0x20001>; }; + +/delete-node/ &pm8994_l1; +/delete-node/ &pm8994_l19; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts index 4c7a90987f08..b5e90c85aaf6 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-ivy.dts @@ -11,3 +11,16 @@ model = "Sony Xperia Z3+/Z4"; compatible = "sony,ivy-row", "qcom,msm8994"; }; + +&pm8994_l3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; +}; + +&pm8994_l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; +}; + +/delete-node/ &pm8994_l19; +/delete-node/ &pm8994_l32; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts index 7e657861387b..743a2a076552 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts @@ -19,3 +19,25 @@ * sii8620 HDMI/MHL bridge @ 72 (kitakami-common) */ }; + +&pm8994_l3 { + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; +}; + +&pm8994_l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; +}; + +&pm8994_l22 { + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; +}; + +&pm8994_l25 { + regulator-min-microvolt = <1037500>; + regulator-max-microvolt = <1037500>; +}; + +/delete-node/ &pm8994_l32; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts index 1081fe6a4d67..1385956a69f3 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-satsuki.dts @@ -11,3 +11,8 @@ model = "Sony Xperia Z5 Premium"; compatible = "sony,satsuki-row", "qcom,msm8994"; }; + +&pm8994_l14 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <1850000>; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts index 5d6bbbf6c119..868a2c9d6496 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts @@ -11,3 +11,5 @@ model = "Sony Xperia Z5"; compatible = "sony,sumire-row", "qcom,msm8994"; }; + +/delete-node/ &pm8994_l19; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts index 2c670ab28613..f129479bbf95 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-suzuran.dts @@ -11,3 +11,10 @@ model = "Sony Xperia Z5 Compact"; compatible = "sony,suzuran-row", "qcom,msm8994"; }; + +&pm8994_l14 { + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; +}; + +/delete-node/ &pm8994_l19; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 71d7187eb090..e31c31c2b936 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -161,59 +161,233 @@ &rpm_requests { pm8994_regulators: pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; - vdd_l1-supply = <&pm8994_s1>; - vdd_l2_26_28-supply = <&pm8994_s3>; - vdd_l3_11-supply = <&pm8994_s3>; - vdd_l4_27_31-supply = <&pm8994_s3>; - vdd_l5_7-supply = <&pm8994_s3>; - vdd_l6_12_32-supply = <&pm8994_s5>; - vdd_l8_16_30-supply = <&vreg_vph_pwr>; - vdd_l9_10_18_22-supply = <&vreg_vph_pwr>; - vdd_l13_19_23_24-supply = <&vreg_vph_pwr>; - vdd_l14_15-supply = <&pm8994_s5>; - vdd_l17_29-supply = <&vreg_vph_pwr>; - vdd_l20_21-supply = <&vreg_vph_pwr>; - vdd_l25-supply = <&pm8994_s5>; - vdd_lvs1_2 = <&pm8994_s4>; - pm8994_s1: s1 {}; - pm8994_s2: s2 {}; - pm8994_s3: s3 {}; - pm8994_s4: s4 {}; - pm8994_s5: s5 {}; - pm8994_s6: s6 {}; - pm8994_s7: s7 {}; + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_l1-supply = <&pmi8994_s1>; + vdd_l2_l26_l28-supply = <&pm8994_s3>; + vdd_l3_l11-supply = <&pm8994_s3>; + vdd_l4_l27_l31-supply = <&pm8994_s3>; + vdd_l5_l7-supply = <&pm8994_s5>; + vdd_l6_l12_l32-supply = <&pm8994_s5>; + vdd_l8_l16_l30-supply = <&vph_pwr>; + vdd_l9_l10_l18_l22-supply = <&pmi8994_bby>; + vdd_l13_l19_l23_l24-supply = <&pmi8994_bby>; + vdd_l14_l15-supply = <&pm8994_s5>; + vdd_l17_l29-supply = <&pmi8994_bby>; + vdd_l20_l21-supply = <&pmi8994_bby>; + vdd_l25-supply = <&pm8994_s3>; + vdd_lvs1_lvs2-supply = <&pm8994_s4>; - pm8994_l1: l1 {}; - pm8994_l2: l2 {}; - pm8994_l3: l3 {}; - pm8994_l4: l4 {}; - pm8994_l6: l6 {}; - pm8994_l8: l8 {}; - pm8994_l9: l9 {}; - pm8994_l10: l10 {}; - pm8994_l11: l11 {}; - pm8994_l12: l12 {}; - pm8994_l13: l13 {}; - pm8994_l14: l14 {}; - pm8994_l15: l15 {}; - pm8994_l16: l16 {}; - pm8994_l17: l17 {}; - pm8994_l18: l18 {}; - pm8994_l19: l19 {}; - pm8994_l20: l20 {}; - pm8994_l21: l21 {}; - pm8994_l22: l22 {}; - pm8994_l23: l23 {}; - pm8994_l24: l24 {}; - pm8994_l25: l25 {}; - pm8994_l26: l26 {}; - pm8994_l27: l27 {}; - pm8994_l28: l28 {}; - pm8994_l29: l29 {}; - pm8994_l30: l30 {}; - pm8994_l31: l31 {}; - pm8994_l32: l32 {}; + /* S1, S2, S6 and S12 are managed by RPMPD */ + + pm8994_s3: s3 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + }; + + pm8994_s4: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-always-on; + regulator-system-load = <325000>; + }; + + pm8994_s5: s5 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + }; + + pm8994_s7: s7 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + /* + * S8 - SPMI-managed VDD_APC0 + * S9, S10 and S11 (the main one) - SPMI-managed VDD_APC1 + */ + + pm8994_l1: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + pm8994_l2: l2 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l3: l3 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + }; + + pm8994_l4: l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + /* L5 is inaccessible from RPM */ + + pm8994_l6: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + /* L7 is inaccessible from RPM */ + + pm8994_l8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l9: l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l10: l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l11: l11 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + pm8994_l12: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l13: l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + pm8994_l14: l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l15: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l16: l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l17: l17 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + }; + + pm8994_l18: l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + }; + + pm8994_l19: l19 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + pm8994_l20: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-boot-on; + regulator-allow-set-load; + regulator-system-load = <570000>; + }; + + pm8994_l21: l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + }; + + pm8994_l22: l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + pm8994_l23: l23 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + pm8994_l24: l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3150000>; + }; + + pm8994_l25: l25 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + pm8994_l26: l26 { + regulator-min-microvolt = <987500>; + regulator-max-microvolt = <987500>; + }; + + pm8994_l27: l27 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + pm8994_l28: l28 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l29: l29 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + pm8994_l30: l30 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + pm8994_l31: l31 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-allow-set-load; + regulator-system-load = <10000>; + }; + + pm8994_l32: l32 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; pm8994_lvs1: lvs1 {}; pm8994_lvs2: lvs2 {}; @@ -222,22 +396,34 @@ pmi8994_regulators: pmi8994-regulators { compatible = "qcom,rpm-pmi8994-regulators"; - pmi8994_s1: s1 {}; - pmi8994_s2: s2 {}; - pmi8994_s3: s3 {}; - pmi8994_bby: boost-bypass {}; + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + pmi8994_s1: s1 { + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + + /* S2 & S3 - VDD_GFX */ + + pmi8994_bby: boost-bypass { + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3600000>; + }; }; }; &sdhc1 { - /* There is an issue with the eMMC causing permanent + /* + * There is an issue with the eMMC causing permanent * damage to the card if a quirk isn't addressed. * Until it's fixed, disable the MMC so as not to brick * devices. */ status = "disabled"; - /* Downstream pushes 2.95V to the sdhci device, + /* + * Downstream pushes 2.95V to the sdhci device, * but upstream driver REALLY wants to make vmmc 1.8v * cause of the hs400-1_8v mode. MMC works fine without * that regulator, so let's not use it for now. From e8528157b7f0bc20dd63867f4946dc5b5195527b Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:26 +0100 Subject: [PATCH 335/584] arm64: dts: qcom: msm8994-kitakami: Add Synaptics RMI touchscreen All Kitakami phones use Synaptics RMI4 touchscreens attached to the same i2c bus. Configure and enable it. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-6-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../msm8994-sony-xperia-kitakami-karin.dts | 2 + .../qcom/msm8994-sony-xperia-kitakami.dtsi | 45 ++++++++++++++++++- 2 files changed, 46 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts index 743a2a076552..4dcf42eafb3a 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts @@ -41,3 +41,5 @@ }; /delete-node/ &pm8994_l32; +/* Z4 tablets use a different touchscreen. */ +/delete-node/ &touchscreen; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index e31c31c2b936..33af174b78ab 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -147,7 +147,34 @@ &blsp_i2c6 { status = "okay"; - /* Synaptics touchscreen */ + touchscreen: rmi4-i2c-dev@2c { + compatible = "syna,rmi4-i2c"; + reg = <0x2c>; + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&tlmm>; + interrupts = <42 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-names = "default"; + pinctrl-0 = <&ts_int_active &ts_reset_active>; + + vdd-supply = <&pm8994_l22>; + vio-supply = <&pm8994_s4>; + + syna,reset-delay-ms = <220>; + syna,startup-delay-ms = <220>; + + rmi4-f01@1 { + reg = <0x01>; + syna,nosleep-mode = <1>; + }; + + rmi4-f11@11 { + reg = <0x11>; + syna,sensor-type = <1>; + }; + }; }; &blsp1_uart2 { @@ -433,3 +460,19 @@ * vqmmc-supply = <&pm8994_s4>; */ }; + +&tlmm { + ts_int_active: ts-int-active { + pins = "gpio42"; + drive-strength = <2>; + bias-disable; + input-enable; + }; + + ts_reset_active: ts-reset-active { + pins = "gpio109"; + drive-strength = <2>; + bias-disable; + output-low; + }; +}; From ab8e4a853731b37297914712b315a9fd6bbee366 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:27 +0100 Subject: [PATCH 336/584] arm64: dts: qcom: msm8994-kitakami: Add uSD card support Assign regulators and enable regulator-set-load on VMMC so as to provide sufficient power. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-7-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 33af174b78ab..26b54f360fc3 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -355,6 +355,8 @@ regulator-min-microvolt = <2950000>; regulator-max-microvolt = <2950000>; regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <800000>; }; pm8994_l22: l22 { @@ -461,6 +463,14 @@ */ }; +&sdhc2 { + status = "okay"; + + cd-gpios = <&tlmm 100 0>; + vmmc-supply = <&pm8994_l21>; + vqmmc-supply = <&pm8994_l13>; +}; + &tlmm { ts_int_active: ts-int-active { pins = "gpio42"; From e9783584c9b7edc8726b4e8858009028d98850f9 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:28 +0100 Subject: [PATCH 337/584] arm64: dts: qcom: msm8994-kitakami: Add VDD_GFX regulator This is required for the GPU to function. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-8-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-sony-xperia-kitakami.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 26b54f360fc3..05155859cf6a 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -185,6 +185,24 @@ status = "okay"; }; +&pmi8994_spmi_regulators { + /* + * Yeah, this one *is* managed by RPMPD, but also needs + * to be hacked up as a-o due to the GPU device only accepting a single + * power domain.. which still isn't enough and forces us to bind + * OXILI_CX and OXILI_GX together! + */ + vdd_gfx: s2@1700 { + reg = <0x1700 0x100>; + regulator-name = "VDD_GFX"; + regulator-min-microvolt = <980000>; + regulator-max-microvolt = <980000>; + + /* hack until we rig up the gpu consumer */ + regulator-always-on; + }; +}; + &rpm_requests { pm8994_regulators: pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; From a046032c37c055757916e36ba3f3a90540d65152 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:29 +0100 Subject: [PATCH 338/584] arm64: dts: qcom: msm8994: Fix BLSP2_UART2 node Fix up the node to make the peripheral functional. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-9-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8994.dtsi | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index 2a6596406d9b..592e18f4628f 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -523,7 +523,7 @@ blsp2_uart2: serial@f995e000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0xf995e000 0x1000>; - interrupts = ; + interrupts = ; clock-names = "core", "iface"; clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; @@ -618,16 +618,18 @@ blsp2_uart2_default: blsp2-uart2-default { function = "blsp_uart8"; - pins = "gpio45", "gpio46"; - drive-strength = <2>; + pins = "gpio45", "gpio46", + "gpio47", "gpio48"; + drive-strength = <16>; bias-disable; }; blsp2_uart2_sleep: blsp2-uart2-sleep { function = "gpio"; - pins = "gpio45", "gpio46"; + pins = "gpio45", "gpio46", + "gpio47", "gpio48"; drive-strength = <2>; - bias-pull-down; + bias-disable; }; i2c1_default: i2c1-default { From 74d6d0a145835bf59fc37e87ea36a22ecaf611be Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:30 +0100 Subject: [PATCH 339/584] arm64: dts: qcom: msm8994/8994-kitakami: Fix up the memory map The previous map was wrong. Fix it up. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-10-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../qcom/msm8994-sony-xperia-kitakami.dtsi | 49 +++++++------------ arch/arm64/boot/dts/qcom/msm8994.dtsi | 45 ++++++++++++++++- 2 files changed, 62 insertions(+), 32 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 05155859cf6a..e962fc5f8b1b 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -72,47 +72,23 @@ }; reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - /* This is for getting crash logs using Android downstream kernels */ ramoops@1fe00000 { compatible = "ramoops"; - reg = <0x0 0x1fe00000 0x0 0x200000>; + reg = <0 0x1fe00000 0 0x200000>; console-size = <0x100000>; record-size = <0x10000>; ftrace-size = <0x10000>; pmsg-size = <0x80000>; }; - continuous_splash: framebuffer@3401000{ - reg = <0x0 0x3401000 0x0 0x2200000>; - no-map; - }; - - dfps_data_mem: dfps_data_mem@3400000 { - reg = <0x0 0x3400000 0x0 0x1000>; - no-map; - }; - - peripheral_region: peripheral_region@7400000 { - reg = <0x0 0x7400000 0x0 0x1c00000>; - no-map; - }; - - modem_region: modem_region@9000000 { - reg = <0x0 0x9000000 0x0 0x5a00000>; - no-map; - }; - - tzapp: modem_region@ea00000 { - reg = <0x0 0xea00000 0x0 0x1900000>; - no-map; - }; - fb_region: fb_region@40000000 { - reg = <0x00 0x40000000 0x00 0x1000000>; + reg = <0 0x40000000 0 0x1000000>; + no-map; + }; + + tzapp: memory@c7800000 { + reg = <0 0xc7800000 0 0x1900000>; no-map; }; }; @@ -185,6 +161,17 @@ status = "okay"; }; +/* + * Kitakami bootloader only turns cont_splash on when it detects + * specific downstream MDSS/backlight nodes in the active DTB. + * One way to use that framebuffer is to load a secondary instance of + * LK with the downstream DTB appended and then, only from there, load + * mainline Linux. + */ +&cont_splash_mem { + reg = <0 0x3401000 0 0x2200000>; +}; + &pmi8994_spmi_regulators { /* * Yeah, this one *is* managed by RPMPD, but also needs diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index 592e18f4628f..e694aaad3c99 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -170,8 +170,51 @@ #size-cells = <2>; ranges; + dfps_data_mem: dfps_data_mem@3400000 { + reg = <0 0x03400000 0 0x1000>; + no-map; + }; + + cont_splash_mem: memory@3800000 { + reg = <0 0x03800000 0 0x2400000>; + no-map; + }; + smem_mem: smem_region@6a00000 { - reg = <0x0 0x6a00000 0x0 0x200000>; + reg = <0 0x06a00000 0 0x200000>; + no-map; + }; + + mpss_mem: memory@7000000 { + reg = <0 0x07000000 0 0x5a00000>; + no-map; + }; + + peripheral_region: memory@ca00000 { + reg = <0 0x0ca00000 0 0x1f00000>; + no-map; + }; + + rmtfs_mem: memory@c6400000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0xc6400000 0 0x180000>; + no-map; + + qcom,client-id = <1>; + }; + + mba_mem: memory@c6700000 { + reg = <0 0xc6700000 0 0x100000>; + no-map; + }; + + audio_mem: memory@c7000000 { + reg = <0 0xc7000000 0 0x800000>; + no-map; + }; + + adsp_mem: memory@c9400000 { + reg = <0 0xc9400000 0 0x3f00000>; no-map; }; }; From 54b1511e4f31e8f849ebbf91be025c9800e0c60d Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Mon, 18 Jan 2021 17:24:31 +0100 Subject: [PATCH 340/584] arm64: dts: qcom: msm8994-kitakami: Add missing email in the copyright I forgot to do this the first time around. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210118162432.107275-11-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts | 2 +- arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts index 868a2c9d6496..d3ba9867a369 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-sumire.dts @@ -1,6 +1,6 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Konrad Dybcio */ /dts-v1/; diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index e962fc5f8b1b..586d866188d7 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -1,6 +1,6 @@ // SPDX-License-Identifier: BSD-3-Clause /* - * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Konrad Dybcio */ #include "msm8994.dtsi" From fcb985a0642ee169c6cf4d2322873f853d50abb2 Mon Sep 17 00:00:00 2001 From: Dave Stevenson Date: Thu, 3 Dec 2020 14:25:43 +0100 Subject: [PATCH 341/584] ARM: dts: bcm2711: Use compatible string for BCM2711 DSI1 Updates the compatible string for DSI1 on BCM2711 to differentiate it from BCM2835. Signed-off-by: Dave Stevenson Signed-off-by: Maxime Ripard Signed-off-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/20201203132543.861591-9-maxime@cerno.tech --- arch/arm/boot/dts/bcm2711.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi index 4847dd305317..f53a51cc91f0 100644 --- a/arch/arm/boot/dts/bcm2711.dtsi +++ b/arch/arm/boot/dts/bcm2711.dtsi @@ -540,6 +540,7 @@ &dsi1 { interrupts = ; + compatible = "brcm,bcm2711-dsi1"; }; &gpio { From 6b4233f70a914d932a8156950bf9114ba6a06f6c Mon Sep 17 00:00:00 2001 From: Nicolas Saenz Julienne Date: Tue, 12 Jan 2021 15:23:40 +0100 Subject: [PATCH 342/584] ARM: dts: bcm2711: Add reserved memory template to hold firmware configuration RPi4's co-processor will copy the board's bootloader[1] configuration into memory for the OS to consume. Specifically, for the bootloader configuration and upgrade user-space routines to query it through nvmem's sysfs interface. Introduce a reserved-memory area template for the co-processor to edit before booting the system so as for Linux not to overwrite that memory and to expose it as an nvmem device. Signed-off-by: Nicolas Saenz Julienne Tested-by: Tim Gover Link: https://lore.kernel.org/r/e8ca9365-a1f2-1f9d-377c-13bf97883cce@linaro.org [1] https://www.raspberrypi.org/documentation/hardware/raspberrypi/bcm2711_bootloader_config.md --- arch/arm/boot/dts/bcm2711-rpi-4-b.dts | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts index 403bacf986eb..3b4ab947492a 100644 --- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts +++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts @@ -25,6 +25,7 @@ emmc2bus = &emmc2bus; ethernet0 = &genet; pcie0 = &pcie0; + blconfig = &blconfig; }; leds { @@ -218,6 +219,22 @@ status = "okay"; }; +&rmem { + /* + * RPi4's co-processor will copy the board's bootloader configuration + * into memory for the OS to consume. It'll also update this node with + * its placement information. + */ + blconfig: nvram@0 { + compatible = "raspberrypi,bootloader-config", "nvmem-rmem"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0 0x0 0x0>; + no-map; + status = "disabled"; + }; +}; + /* SDHCI is used to control the SDIO for wireless */ &sdhci { #address-cells = <1>; From 5878b8087904a5827c3551698be83da1ccf84e11 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 11 Jan 2021 15:23:08 +0100 Subject: [PATCH 343/584] ARM: dts: bcm2711: Add the BSC interrupt controller The BSC controllers used for the HDMI DDC have an interrupt controller shared between both instances. Let's add it to avoid polling. Reviewed-by: Florian Fainelli Signed-off-by: Maxime Ripard Signed-off-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/20210111142309.193441-1-maxime@cerno.tech --- arch/arm/boot/dts/bcm2711.dtsi | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi index f53a51cc91f0..d84e731799b3 100644 --- a/arch/arm/boot/dts/bcm2711.dtsi +++ b/arch/arm/boot/dts/bcm2711.dtsi @@ -308,6 +308,14 @@ #reset-cells = <1>; }; + bsc_intr: interrupt-controller@7ef00040 { + compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; + reg = <0x7ef00040 0x30>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <1>; + }; + hdmi0: hdmi@7ef00700 { compatible = "brcm,bcm2711-hdmi0"; reg = <0x7ef00700 0x300>, @@ -341,6 +349,8 @@ reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>; reg-names = "bsc", "auto-i2c"; clock-frequency = <97500>; + interrupt-parent = <&bsc_intr>; + interrupts = <0>; status = "disabled"; }; @@ -377,6 +387,8 @@ reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>; reg-names = "bsc", "auto-i2c"; clock-frequency = <97500>; + interrupt-parent = <&bsc_intr>; + interrupts = <1>; status = "disabled"; }; }; From fbdc88043c5e9b56368a43584d2d1af07c85fa71 Mon Sep 17 00:00:00 2001 From: Stanislav Jakubek Date: Sun, 24 Jan 2021 16:28:10 +0100 Subject: [PATCH 344/584] ARM: dts: bcm21664: Replace spaces with a tab Fix checkpatch warning: WARNING: please, no spaces at the start of a line Signed-off-by: Stanislav Jakubek Signed-off-by: Florian Fainelli --- arch/arm/boot/dts/bcm21664.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/bcm21664.dtsi b/arch/arm/boot/dts/bcm21664.dtsi index 58ec1b2f8ef6..cc58f2b926b9 100644 --- a/arch/arm/boot/dts/bcm21664.dtsi +++ b/arch/arm/boot/dts/bcm21664.dtsi @@ -27,7 +27,7 @@ bootargs = "console=ttyS0,115200n8"; }; - cpus { + cpus { #address-cells = <1>; #size-cells = <0>; From 3503376d6cc385b6266f93c24ead9a33d8dfe8cb Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Fri, 22 Jan 2021 00:23:20 +0800 Subject: [PATCH 345/584] arm64: dts: rockchip: Move ep-gpios property to nanopc-t4 from nanopi4 Only the NanoPC T4 hs the PCIe reset pin routed to the SoC. For the NanoPi M4 family, no such signal is routed to the expansion header on the base board. As the schematics for the expansion board were not released, it is unclear how this is handled, but the likely answer is that the signal is always pulled high. Move the ep-gpios property from the common nanopi4.dtsi file to the board level nanopc-t4.dts file. This makes the nanopi-m4 lack ep-gpios, matching the board design. A companion patch "PCI: rockchip: make ep_gpio optional" for the Linux driver is required, as the driver currently requires the property to be present. Fixes: e7a095908227 ("arm64: dts: rockchip: Add devicetree for NanoPC-T4") Reviewed-by: Robin Murphy Signed-off-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210121162321.4538-4-wens@kernel.org Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts | 1 + arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi | 1 - 2 files changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts b/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts index e0d75617bb7e..452728b82e42 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dts @@ -95,6 +95,7 @@ }; &pcie0 { + ep-gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_HIGH>; num-lanes = <4>; vpcie3v3-supply = <&vcc3v3_sys>; }; diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi index 76a8b40a93c6..48ed4aaa37f3 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi @@ -504,7 +504,6 @@ }; &pcie0 { - ep-gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_HIGH>; max-link-speed = <2>; num-lanes = <2>; vpcie0v9-supply = <&vcca0v9_s3>; From c7b03115003f7f337ab165542cee37148cf30a8a Mon Sep 17 00:00:00 2001 From: Chen-Yu Tsai Date: Fri, 22 Jan 2021 00:23:21 +0800 Subject: [PATCH 346/584] arm64: dts: rockchip: Add NanoPi M4B board The NanoPi M4B is a minor revision of the original M4. The differences against the original Nanopi M4 that are common with the other M4V2 revision include: - microphone header removed - power button added - recovery button added Additional changes specific to the M4B: - USB 3.0 hub removed; board now has 2x USB 3.0 type-A ports and 2x USB 2.0 ports - ADB toggle switch added; this changes the top USB 3.0 host port to a peripheral port - Type-C port no longer supports data or PD - WiFi/Bluetooth combo chip switched to AP6256, which supports BT 5.0 but only 1T1R (down from 2T2R) for WiFi Add a new dts file for the new board revision that shows the difference against the original. Signed-off-by: Chen-Yu Tsai Link: https://lore.kernel.org/r/20210121162321.4538-5-wens@kernel.org Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/Makefile | 1 + .../boot/dts/rockchip/rk3399-nanopi-m4b.dts | 52 +++++++++++++++++++ 2 files changed, 53 insertions(+) create mode 100644 arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4b.dts diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile index b29a445b355a..62d3abc17a24 100644 --- a/arch/arm64/boot/dts/rockchip/Makefile +++ b/arch/arm64/boot/dts/rockchip/Makefile @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-kobol-helios64.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-leez-p710.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopc-t4.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4b.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4b.dts b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4b.dts new file mode 100644 index 000000000000..72182c58cc46 --- /dev/null +++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4b.dts @@ -0,0 +1,52 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * FriendlyElec NanoPi M4B board device tree source + * + * Copyright (c) 2020 Chen-Yu Tsai + */ + +/dts-v1/; +#include "rk3399-nanopi-m4.dts" + +/ { + model = "FriendlyElec NanoPi M4B"; + compatible = "friendlyarm,nanopi-m4b", "rockchip,rk3399"; + + adc-keys { + compatible = "adc-keys"; + io-channels = <&saradc 1>; + io-channel-names = "buttons"; + keyup-threshold-microvolt = <1500000>; + poll-interval = <100>; + + recovery { + label = "Recovery"; + linux,code = ; + press-threshold-microvolt = <18000>; + }; + }; +}; + +/* No USB type-C PD power manager */ +/delete-node/ &fusb0; + +&i2c4 { + status = "disabled"; +}; + +&u2phy0_host { + phy-supply = <&vcc5v0_usb2>; +}; + +&u2phy0_otg { + phy-supply = <&vbus_typec>; +}; + +&u2phy1_otg { + phy-supply = <&vcc5v0_usb1>; +}; + +&vbus_typec { + enable-active-high; + gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; +}; From 5eae5696eed5cc460867521c3c67db9ab62e1a0d Mon Sep 17 00:00:00 2001 From: Robin Murphy Date: Wed, 20 Jan 2021 23:42:22 +0000 Subject: [PATCH 347/584] ARM: dts: rockchip: Remove bogus "amba" bus nodes The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful purpose, and certainly bear no relation at all to the actual underlying interconnect topology. They appear to be cargo-cult copying from a design misstep in the very early days of FDT adoption on ARM, which was righted with the "arm,primecell" compatible, and the last trace of the idea finally purged by commit 2ef7d5f342c1 ("ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus""). As such, they can simply be removed and the DMA-330 nodes fitted into the normal sort order. Signed-off-by: Robin Murphy Link: https://lore.kernel.org/r/e682edd25133bde2ed8198138febc90071530a51.1611186142.git.robin.murphy@arm.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk3036.dtsi | 31 ++++++-------- arch/arm/boot/dts/rk322x.dtsi | 29 +++++-------- arch/arm/boot/dts/rk3288.dtsi | 81 ++++++++++++++++------------------- arch/arm/boot/dts/rk3xxx.dtsi | 81 ++++++++++++++++------------------- 4 files changed, 97 insertions(+), 125 deletions(-) diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi index dda5a1f79aca..47a787a12e55 100644 --- a/arch/arm/boot/dts/rk3036.dtsi +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -54,25 +54,6 @@ }; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - pdma: pdma@20078000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x20078000 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC2>; - clock-names = "apb_pclk"; - }; - }; - arm-pmu { compatible = "arm,cortex-a7-pmu"; interrupts = , @@ -509,6 +490,18 @@ status = "disabled"; }; + pdma: pdma@20078000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x20078000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC2>; + clock-names = "apb_pclk"; + }; + pinctrl: pinctrl { compatible = "rockchip,rk3036-pinctrl"; rockchip,grf = <&grf>; diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi index 48e6e8d44a1a..4d003afd0e3e 100644 --- a/arch/arm/boot/dts/rk322x.dtsi +++ b/arch/arm/boot/dts/rk322x.dtsi @@ -95,24 +95,6 @@ }; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - pdma: pdma@110f0000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x110f0000 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC>; - clock-names = "apb_pclk"; - }; - }; - arm-pmu { compatible = "arm,cortex-a7-pmu"; interrupts = , @@ -464,6 +446,17 @@ <75000000>; }; + pdma: pdma@110f0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x110f0000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC>; + clock-names = "apb_pclk"; + }; + thermal-zones { cpu_thermal: cpu-thermal { polling-delay-passive = <100>; /* milliseconds */ diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi index 29ffe2eb9bf9..ea7416c31f9b 100644 --- a/arch/arm/boot/dts/rk3288.dtsi +++ b/arch/arm/boot/dts/rk3288.dtsi @@ -154,50 +154,6 @@ }; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - dmac_peri: dma-controller@ff250000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff250000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC2>; - clock-names = "apb_pclk"; - }; - - dmac_bus_ns: dma-controller@ff600000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff600000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC1>; - clock-names = "apb_pclk"; - status = "disabled"; - }; - - dmac_bus_s: dma-controller@ffb20000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xffb20000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC1>; - clock-names = "apb_pclk"; - }; - }; - reserved-memory { #address-cells = <2>; #size-cells = <2>; @@ -487,6 +443,18 @@ status = "disabled"; }; + dmac_peri: dma-controller@ff250000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff250000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC2>; + clock-names = "apb_pclk"; + }; + thermal-zones { reserve_thermal: reserve-thermal { polling-delay-passive = <1000>; /* milliseconds */ @@ -665,6 +633,19 @@ status = "disabled"; }; + dmac_bus_ns: dma-controller@ff600000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff600000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC1>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + i2c0: i2c@ff650000 { compatible = "rockchip,rk3288-i2c"; reg = <0x0 0xff650000 0x0 0x1000>; @@ -1398,6 +1379,18 @@ reg = <0x0 0xffaf0080 0x0 0x20>; }; + dmac_bus_s: dma-controller@ffb20000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xffb20000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC1>; + clock-names = "apb_pclk"; + }; + efuse: efuse@ffb40000 { compatible = "rockchip,rk3288-efuse"; reg = <0x0 0xffb40000 0x0 0x20>; diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rk3xxx.dtsi index d3eb25844e97..755c946f11de 100644 --- a/arch/arm/boot/dts/rk3xxx.dtsi +++ b/arch/arm/boot/dts/rk3xxx.dtsi @@ -32,50 +32,6 @@ spi1 = &spi1; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - dmac1_s: dma-controller@20018000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x20018000 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMA1>; - clock-names = "apb_pclk"; - }; - - dmac1_ns: dma-controller@2001c000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x2001c000 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMA1>; - clock-names = "apb_pclk"; - status = "disabled"; - }; - - dmac2: dma-controller@20078000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x20078000 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMA2>; - clock-names = "apb_pclk"; - }; - }; - xin24m: oscillator { compatible = "fixed-clock"; clock-frequency = <24000000>; @@ -304,6 +260,31 @@ reg = <0x20008000 0x200>; }; + dmac1_s: dma-controller@20018000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x20018000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMA1>; + clock-names = "apb_pclk"; + }; + + dmac1_ns: dma-controller@2001c000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x2001c000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMA1>; + clock-names = "apb_pclk"; + status = "disabled"; + }; + i2c0: i2c@2002d000 { compatible = "rockchip,rk3066-i2c"; reg = <0x2002d000 0x1000>; @@ -478,4 +459,16 @@ dma-names = "tx", "rx"; status = "disabled"; }; + + dmac2: dma-controller@20078000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x20078000 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMA2>; + clock-names = "apb_pclk"; + }; }; From 94e8a5f6d0dee8e81bdcef6d3e86a027459df225 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Mon, 18 Jan 2021 16:52:38 +0100 Subject: [PATCH 348/584] ARM: dts: rockchip: assign a fixed index to mmc devices on rk322x boards Recently introduced async probe on mmc devices can shuffle block IDs. Pin them to fixed values to ease booting in environments where UUIDs are not practical. Use newly introduced aliases for mmcblk devices from [1]. The sort order is based on reg address. [1] https://patchwork.kernel.org/patch/11747669/ Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210118155242.7172-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rk322x.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi index 4d003afd0e3e..a4dd50aaf3fc 100644 --- a/arch/arm/boot/dts/rk322x.dtsi +++ b/arch/arm/boot/dts/rk322x.dtsi @@ -14,6 +14,9 @@ interrupt-parent = <&gic>; aliases { + mmc0 = &sdmmc; + mmc1 = &sdio; + mmc2 = &emmc; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; From 1034e2b6b8435758c0d699b77761365fd09a5f4a Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Mon, 18 Jan 2021 16:52:39 +0100 Subject: [PATCH 349/584] ARM: dts: rockchip: assign a fixed index to mmc devices on rv1108 boards Recently introduced async probe on mmc devices can shuffle block IDs. Pin them to fixed values to ease booting in environments where UUIDs are not practical. Use newly introduced aliases for mmcblk devices from [1]. The sort order is based on reg address. [1] https://patchwork.kernel.org/patch/11747669/ Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210118155242.7172-2-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm/boot/dts/rv1108.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/rv1108.dtsi b/arch/arm/boot/dts/rv1108.dtsi index 15fa25585ea4..7319a2473b80 100644 --- a/arch/arm/boot/dts/rv1108.dtsi +++ b/arch/arm/boot/dts/rv1108.dtsi @@ -19,6 +19,9 @@ i2c1 = &i2c1; i2c2 = &i2c2; i2c3 = &i2c3; + mmc0 = &emmc; + mmc1 = &sdio; + mmc2 = &sdmmc; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; From e5a58ad1cdc882ea4ef6fdd47b1018bfaac49b61 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Andr=C3=A9=20Hentschel?= Date: Sun, 27 Dec 2020 18:13:53 +0100 Subject: [PATCH 350/584] ARM: dts: omap3-echo: Add speaker sound card support MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This adds audio playback to the first generation Amazon Echo Signed-off-by: André Hentschel Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-echo.dts | 67 ++++++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) diff --git a/arch/arm/boot/dts/omap3-echo.dts b/arch/arm/boot/dts/omap3-echo.dts index 93ffeddada1e..b9fd113979f2 100644 --- a/arch/arm/boot/dts/omap3-echo.dts +++ b/arch/arm/boot/dts/omap3-echo.dts @@ -86,6 +86,38 @@ linux,axis = ; rotary-encoder,relative-axis; }; + + speaker_amp: speaker-amplifier { + compatible = "simple-audio-amplifier"; + enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* gpio_129 */ + sound-name-prefix = "Speaker Amp"; + VCC-supply = <&vcc1v8>; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "Misto Speaker"; + simple-audio-card,widgets = + "Speaker", "Speaker"; + simple-audio-card,routing = + "Speaker Amp INL", "HPL", + "Speaker Amp INR", "HPR", + "Speaker", "Speaker Amp OUTL", + "Speaker", "Speaker Amp OUTR"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound_master>; + simple-audio-card,frame-master = <&sound_master>; + simple-audio-card,aux-devs = <&speaker_amp>; + + simple-audio-card,cpu { + sound-dai = <&mcbsp2>; + }; + + sound_master: simple-audio-card,codec { + sound-dai = <&codec0>; + system-clock-frequency = <19200000>; + }; + }; }; &i2c1 { @@ -96,6 +128,13 @@ }; }; +&mcbsp2 { + status = "okay"; + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; +}; + &i2c2 { clock-frequency = <400000>; @@ -277,6 +316,22 @@ }; }; +&i2c3 { + clock-frequency = <400000>; + + codec0: codec@18 { + #sound-dai-cells = <0>; + compatible = "ti,tlv320aic32x4"; + reg = <0x18>; + clocks = <&sys_clkout1>; + clock-names = "mclk"; + ldoin-supply = <&vcc1v8>; + iov-supply = <&vcc1v8>; + reset-gpios = <&gpio3 10 GPIO_ACTIVE_LOW>; /* gpio_74 */ + }; +}; + + #include "tps65910.dtsi" &omap3_pmx_core { @@ -290,6 +345,9 @@ pinctrl-single,pins = < OMAP3_CORE1_IOPAD(0x20dc, PIN_INPUT | MUX_MODE4) /* dss_data0.gpio_70 */ OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4) /* dss_data2.gpio_72 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* dss_data4.gpio_74 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* dss_data15.gpio_85 */ + OMAP3_CORE1_IOPAD(0x2a1a, PIN_OUTPUT | MUX_MODE0) /* sys_clkout1.sys_clkout1 */ >; }; @@ -318,6 +376,15 @@ OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7.sdmmc2_dat7 */ >; }; + + mcbsp2_pins: pinmux_mcbsp2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ + OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx.mcbsp2_clkx */ + OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr.mcbsp2.dr */ + OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx.mcbsp2_dx */ + >; + }; }; &omap3_pmx_core2 { From 44f416879a442600b006ef7dec3a6dc98bcf59c6 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 30 Dec 2020 10:42:30 +0200 Subject: [PATCH 351/584] ARM: dts: Configure missing thermal interrupt for 4430 We have gpio_86 wired internally to the bandgap thermal shutdown interrupt on 4430 like we have it on 4460 according to the TRM. This can be found easily by searching for TSHUT. For some reason the thermal shutdown interrupt was never added for 4430, let's add it. I believe this is needed for the thermal shutdown interrupt handler ti_bandgap_tshut_irq_handler() to call orderly_poweroff(). Fixes: aa9bb4bb8878 ("arm: dts: add omap4430 thermal data") Cc: Carl Philipp Klemm Cc: Daniel Lezcano Cc: Eduardo Valentin Cc: Merlijn Wajer Cc: Pavel Machek Cc: Peter Ujfalusi Cc: Sebastian Reichel Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap443x.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/omap443x.dtsi b/arch/arm/boot/dts/omap443x.dtsi index cb309743de5d..dd8ef58cbaed 100644 --- a/arch/arm/boot/dts/omap443x.dtsi +++ b/arch/arm/boot/dts/omap443x.dtsi @@ -33,10 +33,12 @@ }; ocp { + /* 4430 has only gpio_86 tshut and no talert interrupt */ bandgap: bandgap@4a002260 { reg = <0x4a002260 0x4 0x4a00232C 0x4>; compatible = "ti,omap4430-bandgap"; + gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; #thermal-sensor-cells = <0>; }; From 5c3db2d4d4ed747e714387362afe007e6ae5e2d3 Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Wed, 30 Dec 2020 10:42:31 +0200 Subject: [PATCH 352/584] ARM: dts: motorola-mapphone: Configure lower temperature passive cooling The current cooling device temperature is too high at 100C as we have a battery on the device right next to the SoC as pointed out by Carl Philipp Klemm . Let's configure the max temperature to 80C. As we only have a tshut interrupt and no talert interrupt on 4430, we have a passive cooling device configured for 4430. However, we want the poll interval to be 10 seconds instead of 1 second for power management. The value of 10 seconds seems like plenty of time to notice the temperature increase above the 75C temperatures. Having the bandgap temperature change seems to take several tens of seconds because of heat dissipation above 75C range as monitored with a full CPU load. Cc: Carl Philipp Klemm Cc: Merlijn Wajer Cc: Pavel Machek Cc: Sebastian Reichel Suggested-by: Carl Philipp Klemm Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/motorola-mapphone-common.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi index f75806d0cd47..9573ddc4ed9c 100644 --- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi +++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi @@ -169,6 +169,14 @@ }; }; +&cpu_thermal { + polling-delay = <10000>; /* milliseconds */ +}; + +&cpu_alert0 { + temperature = <80000>; /* millicelsius */ +}; + &dss { status = "okay"; }; From 19e367147ea8864dff1fb153cfab6d8e8da10324 Mon Sep 17 00:00:00 2001 From: Carl Philipp Klemm Date: Wed, 30 Dec 2020 10:42:32 +0200 Subject: [PATCH 353/584] ARM: dts: motorola-mapphone: Add 1.2GHz OPP The omap4430 HS HIGH performance devces support 1.2GHz opp, lower speed variants do not. However for mapphone devices Motorola seems to have decided that this does not really matter for the SoC variants they have tested to use, and decided to clock all devices, including the ones with STANDARD performance chips at 1.2GHz upon release of the 3.0.8 vendor kernel shiped with Android 4.0. Therefore it seems safe to do the same, but let's only do it for Motorola devices as the others have not been tested. Note that we prevent overheating with the passive cooling device cpu_alert0 configured in the dts file that starts lowering the speed as needed. This also removes the "failed to find current OPP for freq 1200000000" warning. Cc: Merlijn Wajer Cc: Pavel Machek Cc: Sebastian Reichel Signed-off-by: Carl Philipp Klemm [tony@atomide.com: made motorola specific, updated comments] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/motorola-mapphone-common.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi index 9573ddc4ed9c..a4423ff0df39 100644 --- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi +++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi @@ -177,6 +177,21 @@ temperature = <80000>; /* millicelsius */ }; +&cpu0 { + /* + * Note that the 1.2GiHz mode is enabled for all SoC variants for + * the Motorola Android Linux v3.0.8 based kernel. + */ + operating-points = < + /* kHz uV */ + 300000 1025000 + 600000 1200000 + 800000 1313000 + 1008000 1375000 + 1200000 1375000 + >; +}; + &dss { status = "okay"; }; From fab030ac99978d235ca3889262b28d93c8bccd30 Mon Sep 17 00:00:00 2001 From: Carl Philipp Klemm Date: Mon, 4 Jan 2021 20:56:31 +0100 Subject: [PATCH 354/584] ARM: dts: omap443x: Correct sgx clock to 307.2MHz as used on motorola vendor kernel The Android vendor kernel uses 307.2MHz or a divider ratio of /5 while active 153600000 or /10 is only used when the sgx core is inactive. Signed-off-by: Carl Philipp Klemm Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap443x.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/omap443x.dtsi b/arch/arm/boot/dts/omap443x.dtsi index dd8ef58cbaed..8466161197ae 100644 --- a/arch/arm/boot/dts/omap443x.dtsi +++ b/arch/arm/boot/dts/omap443x.dtsi @@ -78,11 +78,11 @@ /include/ "omap443x-clocks.dtsi" /* - * Use dpll_per for sgx at 153.6MHz like droid4 stock v3.0.8 Android kernel + * Use dpll_per for sgx at 307.2MHz like droid4 stock v3.0.8 Android kernel */ &sgx_module { assigned-clocks = <&l3_gfx_clkctrl OMAP4_GPU_CLKCTRL 24>, <&dpll_per_m7x2_ck>; - assigned-clock-rates = <0>, <153600000>; + assigned-clock-rates = <0>, <307200000>; assigned-clock-parents = <&dpll_per_m7x2_ck>; }; From 5f1bf7ae848104b7cb589e03a9bbef61a9a62612 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Sat, 9 Jan 2021 11:01:03 -0600 Subject: [PATCH 355/584] ARM: dts: omap36xx: Remove turbo mode for 1GHz variants Previously, the 1GHz variants were marked as a turbo, because that variant has reduced thermal operating range. Now that the thermal throttling is in place, it should be safe to remove the turbo-mode from the 1GHz variants, because the CPU will automatically slow if the thermal limit is reached. Signed-off-by: Adam Ford Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap36xx.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index 05fe5ed127b0..20844dbc002e 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -72,7 +72,6 @@ <1375000 1375000 1375000>; /* only on am/dm37x with speed-binned bit set */ opp-supported-hw = <0xffffffff 2>; - turbo-mode; }; }; From 00dba495f1a20fa3e4dc4c4fbd54dde477692be8 Mon Sep 17 00:00:00 2001 From: Javier Martinez Canillas Date: Mon, 18 Jan 2021 09:17:07 +0100 Subject: [PATCH 356/584] ARM: dts: omap3-igep: Change email address in copyright notice I've switched employer a long time ago and the mentioned email address no longer exists. Use my personal address to prevent the issue in the future. Signed-off-by: Javier Martinez Canillas Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap3-igep.dtsi | 2 +- arch/arm/boot/dts/omap3-igep0020-common.dtsi | 2 +- arch/arm/boot/dts/omap3-igep0020-rev-f.dts | 2 +- arch/arm/boot/dts/omap3-igep0020.dts | 2 +- arch/arm/boot/dts/omap3-igep0030-common.dtsi | 2 +- arch/arm/boot/dts/omap3-igep0030-rev-g.dts | 2 +- arch/arm/boot/dts/omap3-igep0030.dts | 2 +- 7 files changed, 7 insertions(+), 7 deletions(-) diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 5de2be9bbe6f..99f5585097a1 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -2,7 +2,7 @@ /* * Common device tree for IGEP boards based on AM/DM37x * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra */ /dts-v1/; diff --git a/arch/arm/boot/dts/omap3-igep0020-common.dtsi b/arch/arm/boot/dts/omap3-igep0020-common.dtsi index af8aa5f0feb7..73d8f471b9ec 100644 --- a/arch/arm/boot/dts/omap3-igep0020-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0020-common.dtsi @@ -2,7 +2,7 @@ /* * Common Device Tree Source for IGEPv2 * - * Copyright (C) 2014 Javier Martinez Canillas + * Copyright (C) 2014 Javier Martinez Canillas * Copyright (C) 2014 Enric Balletbo i Serra */ diff --git a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts index 567232584f08..9dca5bfc87ab 100644 --- a/arch/arm/boot/dts/omap3-igep0020-rev-f.dts +++ b/arch/arm/boot/dts/omap3-igep0020-rev-f.dts @@ -2,7 +2,7 @@ /* * Device Tree Source for IGEPv2 Rev. F (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra */ diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index e341535a7162..c6f863bc03ad 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -2,7 +2,7 @@ /* * Device Tree Source for IGEPv2 Rev. C (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra */ diff --git a/arch/arm/boot/dts/omap3-igep0030-common.dtsi b/arch/arm/boot/dts/omap3-igep0030-common.dtsi index 71b0ae807ecd..742e3e147063 100644 --- a/arch/arm/boot/dts/omap3-igep0030-common.dtsi +++ b/arch/arm/boot/dts/omap3-igep0030-common.dtsi @@ -2,7 +2,7 @@ /* * Common Device Tree Source for IGEP COM MODULE * - * Copyright (C) 2014 Javier Martinez Canillas + * Copyright (C) 2014 Javier Martinez Canillas * Copyright (C) 2014 Enric Balletbo i Serra */ diff --git a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts index df6ba1219830..8e9c12cf51a7 100644 --- a/arch/arm/boot/dts/omap3-igep0030-rev-g.dts +++ b/arch/arm/boot/dts/omap3-igep0030-rev-g.dts @@ -2,7 +2,7 @@ /* * Device Tree Source for IGEP COM MODULE Rev. G (TI OMAP AM/DM37x) * - * Copyright (C) 2014 Javier Martinez Canillas + * Copyright (C) 2014 Javier Martinez Canillas * Copyright (C) 2014 Enric Balletbo i Serra */ diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 32f31035daa2..5188f96f431e 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -2,7 +2,7 @@ /* * Device Tree Source for IGEP COM MODULE Rev. E (TI OMAP AM/DM37x) * - * Copyright (C) 2012 Javier Martinez Canillas + * Copyright (C) 2012 Javier Martinez Canillas * Copyright (C) 2012 Enric Balletbo i Serra */ From 4231f3a72f9ac7f8738d003b7ad56fa998574fb8 Mon Sep 17 00:00:00 2001 From: Alexander Shiyan Date: Mon, 25 Jan 2021 13:50:11 +0300 Subject: [PATCH 357/584] ARM: dts: am335x-myirtech-*: Add DT for AM335X MYIR Tech Limited board This patch adds basic support for MYIR Tech MYC-AM335X CPU Module: - Up to 1GHz TI AM335X Series ARM Cortex-A8 Processors - Up to 512MB DDR3 SDRAM - Up to 512MB Nand Flash and MYD-AM335X Development Board: - MYC-AM335X CPU Module as Controller Board - Serial ports, 4 x USB Host, OTG, 2 x Gigabit Ethernet, CAN, RS485, TF, Audio - Supports HDMI and LCD Display Signed-off-by: Alexander Shiyan Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/am335x-myirtech-myc.dtsi | 267 ++++++++++ arch/arm/boot/dts/am335x-myirtech-myd.dts | 536 +++++++++++++++++++++ 3 files changed, 804 insertions(+) create mode 100644 arch/arm/boot/dts/am335x-myirtech-myc.dtsi create mode 100644 arch/arm/boot/dts/am335x-myirtech-myd.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..511b058fb69e 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -817,6 +817,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \ am335x-lxm.dtb \ am335x-moxa-uc-2101.dtb \ am335x-moxa-uc-8100-me-t.dtb \ + am335x-myirtech-myd.dtb \ am335x-nano.dtb \ am335x-netcan-plus-1xx.dtb \ am335x-netcom-plus-2xx.dtb \ diff --git a/arch/arm/boot/dts/am335x-myirtech-myc.dtsi b/arch/arm/boot/dts/am335x-myirtech-myc.dtsi new file mode 100644 index 000000000000..270a3d5e8f98 --- /dev/null +++ b/arch/arm/boot/dts/am335x-myirtech-myc.dtsi @@ -0,0 +1,267 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* SPDX-FileCopyrightText: Alexander Shiyan, */ + +/* Based on code by myc_c335x.dts, MYiRtech.com */ +/* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */ + +/dts-v1/; + +#include "am33xx.dtsi" + +#include +#include + +/ { + model = "MYIR MYC-AM335X"; + compatible = "myir,myc-am335x", "ti,am33xx"; + + cpus { + cpu@0 { + cpu0-supply = <&vdd_core>; + voltage-tolerance = <2>; + }; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + vdd_mod: vdd_mod_reg { + compatible = "regulator-fixed"; + regulator-name = "vdd-mod"; + regulator-always-on; + regulator-boot-on; + }; + + vdd_core: vdd_core_reg { + compatible = "regulator-fixed"; + regulator-name = "vdd-core"; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mod>; + }; + + leds: leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_mod_pins>; + + led_mod: led_mod { + label = "module:user"; + gpios = <&gpio3 18 GPIO_ACTIVE_LOW>; + color = ; + default-state = "off"; + panic-indicator; + }; + }; +}; + +&cpsw_emac0 { + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; +}; + +&davinci_mdio { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mdio_pins_default>; + pinctrl-1 = <&mdio_pins_sleep>; + status = "okay"; + + phy0: ethernet-phy@4 { + reg = <4>; + }; +}; + +&elm { + status = "okay"; +}; + +&gpmc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&nand_pins_default>; + pinctrl-1 = <&nand_pins_sleep>; + ranges = <0 0 0x8000000 0x1000000>; + status = "okay"; + + nand0: nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE_NONE>; + nand-bus-width = <8>; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <44>; + gpmc,cs-wr-off-ns = <44>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <34>; + gpmc,adv-wr-off-ns = <44>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <40>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <54>; + gpmc,access-ns = <64>; + gpmc,rd-cycle-ns = <82>; + gpmc,wr-cycle-ns = <82>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + ti,elm-id = <&elm>; + ti,nand-ecc-opt = "bch8"; + + #address-cells = <1>; + #size-cells = <1>; + }; +}; + +&i2c0 { + pinctrl-names = "default", "gpio", "sleep"; + pinctrl-0 = <&i2c0_pins_default>; + pinctrl-1 = <&i2c0_pins_gpio>; + pinctrl-2 = <&i2c0_pins_sleep>; + clock-frequency = <400000>; + scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + eeprom: eeprom@50 { + compatible = "atmel,24c32"; + reg = <0x50>; + pagesize = <32>; + vcc-supply = <&vdd_mod>; + }; +}; + +&mac { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <ð_slave1_pins_default>; + pinctrl-1 = <ð_slave1_pins_sleep>; + slaves = <1>; + status = "okay"; +}; + +&rtc { + system-power-controller; +}; + +&am33xx_pinmux { + mdio_pins_default: pinmux_mdio_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0) /* mdio_data */ + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0) /* mdio_clk */ + >; + }; + + mdio_pins_sleep: pinmux_mdio_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + eth_slave1_pins_default: pinmux_eth_slave1_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii1_tctl */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii1_rctl */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii1_td3 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii1_td2 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii1_td1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii1_td0 */ + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii1_tclk */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii1_rclk */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii1_rd3 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii1_rd2 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii1_rd1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii1_rd0 */ + >; + }; + + eth_slave1_pins_sleep: pinmux_eth_slave1_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + i2c0_pins_default: pinmux_i2c0_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE0) /* I2C0_SDA */ + AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE0) /* I2C0_SCL */ + >; + }; + + i2c0_pins_gpio: pinmux_i2c0_pins_gpio { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE7) /* gpio3[5] */ + AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE7) /* gpio3[6] */ + >; + }; + + i2c0_pins_sleep: pinmux_i2c0_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + led_mod_pins: pinmux_led_mod_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE7) /* gpio3[18] */ + >; + }; + + nand_pins_default: pinmux_nand_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad0 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad1 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad2 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad3 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad4 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad5 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad6 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_ad7 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0) /* gpmc_wait0 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7) /* gpio0[31] */ + AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0) /* gpmc_csn0 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0) /* gpmc_advn_ale */ + AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_OUTPUT, MUX_MODE0) /* gpmc_oen_ren */ + AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_OUTPUT, MUX_MODE0) /* gpmc_wen */ + AM33XX_PADCONF(AM335X_PIN_GPMC_BEN0_CLE, PIN_OUTPUT, MUX_MODE0) /* gpmc_be0n_cle */ + >; + }; + + nand_pins_sleep: pinmux_nand_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_BEN0_CLE, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; +}; diff --git a/arch/arm/boot/dts/am335x-myirtech-myd.dts b/arch/arm/boot/dts/am335x-myirtech-myd.dts new file mode 100644 index 000000000000..c996639874e6 --- /dev/null +++ b/arch/arm/boot/dts/am335x-myirtech-myd.dts @@ -0,0 +1,536 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* SPDX-FileCopyrightText: Alexander Shiyan, */ +/* Based on code by myd_c335x.dts, MYiRtech.com */ +/* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */ + +/dts-v1/; + +#include "am335x-myirtech-myc.dtsi" + +#include +#include + +/ { + model = "MYIR MYD-AM335X"; + compatible = "myir,myd-am335x", "myir,myc-am335x", "ti,am33xx"; + + chosen { + stdout-path = &uart0; + }; + + clk12m: clk12m { + compatible = "fixed-clock"; + clock-frequency = <12000000>; + + #clock-cells = <0>; + }; + + gpio_buttons: gpio_buttons { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_buttons_pins>; + #address-cells = <1>; + #size-cells = <0>; + + button1: button@0 { + reg = <0>; + label = "button1"; + linux,code = ; + gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + }; + + button2: button@1 { + reg = <1>; + label = "button2"; + linux,code = ; + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + }; + + sound: sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&master_codec>; + simple-audio-card,frame-master = <&master_codec>; + + simple-audio-card,cpu { + sound-dai = <&mcasp0>; + }; + + master_codec: simple-audio-card,codec@1 { + sound-dai = <&sgtl5000>; + }; + + simple-audio-card,codec@2 { + sound-dai = <&tda9988>; + }; + }; + + vdd_5v0: vdd_5v0_reg { + compatible = "regulator-fixed"; + regulator-name = "vdd_5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3: vdd_3v3_reg { + compatible = "regulator-fixed"; + regulator-name = "vdd-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_5v0>; + }; +}; + +&cpsw_emac1 { + phy-handle = <&phy1>; + phy-mode = "rgmii-id"; +}; + +&davinci_mdio { + phy1: ethernet-phy@6 { + reg = <6>; + eee-broken-1000t; + }; +}; + +&dcan0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcan0_pins_default>; + pinctrl-1 = <&dcan0_pins_sleep>; + status = "okay"; +}; + +&dcan1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&dcan1_pins_default>; + pinctrl-1 = <&dcan1_pins_sleep>; + status = "okay"; +}; + +&ehrpwm0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&ehrpwm0_pins_default>; + pinctrl-1 = <&ehrpwm0_pins_sleep>; + status = "okay"; +}; + +&epwmss0 { + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default", "gpio", "sleep"; + pinctrl-0 = <&i2c1_pins_default>; + pinctrl-1 = <&i2c1_pins_gpio>; + pinctrl-2 = <&i2c1_pins_sleep>; + clock-frequency = <400000>; + scl-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + status = "okay"; + + sgtl5000: sgtl5000@a { + compatible = "fsl,sgtl5000"; + reg =<0xa>; + clocks = <&clk12m>; + micbias-resistor-k-ohms = <4>; + micbias-voltage-m-volts = <2250>; + VDDA-supply = <&vdd_3v3>; + VDDIO-supply = <&vdd_3v3>; + + #sound-dai-cells = <0>; + }; + + tda9988: tda9988@70 { + compatible = "nxp,tda998x"; + reg =<0x70>; + audio-ports = ; + + #sound-dai-cells = <0>; + + ports { + port@0 { + hdmi_0: endpoint@0 { + remote-endpoint = <&lcdc_0>; + }; + }; + }; + }; +}; + +&lcdc { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&lcdc_pins_default>; + pinctrl-1 = <&lcdc_pins_sleep>; + blue-and-red-wiring = "straight"; + status = "okay"; + + port { + lcdc_0: endpoint@0 { + remote-endpoint = <&hdmi_0>; + }; + }; +}; + +&leds { + pinctrl-0 = <&led_mod_pins &leds_pins>; + + led1: led1 { + label = "base:user1"; + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + color = ; + default-state = "off"; + }; + + led2: led2 { + label = "base:user2"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + color = ; + default-state = "off"; + }; +}; + +&mac { + pinctrl-0 = <ð_slave1_pins_default>, <ð_slave2_pins_default>; + pinctrl-1 = <ð_slave1_pins_sleep>, <ð_slave2_pins_sleep>; + slaves = <2>; +}; + +&mcasp0 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mcasp0_pins_default>; + pinctrl-1 = <&mcasp0_pins_sleep>; + op-mode = <0>; + tdm-slots = <2>; + serial-dir = <0 1 2 0>; + tx-num-evt = <32>; + rx-num-evt = <32>; + status = "okay"; + + #sound-dai-cells = <0>; +}; + +&mmc1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&mmc1_pins_default>; + pinctrl-1 = <&mmc1_pins_sleep>; + cd-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>; + bus-width = <4>; + vmmc-supply = <&vdd_3v3>; + status = "okay"; +}; + +&nand0 { + partition@0 { + label = "MLO"; + reg = <0x00000 0x20000>; + }; + + partition@20000 { + label = "boot"; + reg = <0x20000 0x80000>; + }; +}; + +&tscadc { + status = "okay"; + + adc: adc { + ti,adc-channels = <0 1 2 3 4 5 6>; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart1_pins_default>; + pinctrl-1 = <&uart1_pins_sleep>; + linux,rs485-enabled-at-boot-time; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&uart2_pins_default>; + pinctrl-1 = <&uart2_pins_sleep>; + status = "okay"; +}; + +&usb { + pinctrl-names = "default"; + pinctrl-0 = <&usb_pins>; +}; + +&usb0 { + dr_mode = "otg"; +}; + +&usb0_phy { + vcc-supply = <&vdd_5v0>; +}; + +&usb1 { + dr_mode = "host"; +}; + +&usb1_phy { + vcc-supply = <&vdd_5v0>; +}; + +&vdd_mod { + vin-supply = <&vdd_3v3>; +}; + +&am33xx_pinmux { + dcan0_pins_default: pinmux_dcan0_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE2) /* dcan0_tx_mux2 */ + AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT, MUX_MODE2) /* dcan0_rx_mux2 */ + >; + }; + + dcan0_pins_sleep: pinmux_dcan0_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + dcan1_pins_default: pinmux_dcan1_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2) /* dcan1_tx_mux0 */ + AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2) /* dcan1_rx_mux0 */ + >; + }; + + dcan1_pins_sleep: pinmux_dcan1_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + ehrpwm0_pins_default: pinmux_ehrpwm0_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_OUTPUT, MUX_MODE3) /* ehrpwm0A_mux1 */ + >; + }; + + ehrpwm0_pins_sleep: pinmux_ehrpwm0_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + eth_slave2_pins_default: pinmux_eth_slave2_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii2_tctl */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii2_rctl */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii2_td3 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii2_td2 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii2_td1 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii2_td0 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLDOWN, MUX_MODE2) /* rgmii2_tclk */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii2_rclk */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii2_rd3 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE2) /* rgmii2_rd2 */ + AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE2 /* rgmii2_rd1 */) + AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE2 /* rgmii2_rd0 */) + >; + }; + + eth_slave2_pins_sleep: pinmux_eth_slave2_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + gpio_buttons_pins: pinmux_gpio_buttons_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLDOWN, MUX_MODE7) /* gpio3[0] */ + AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT, MUX_MODE7) /* gpio0[29] */ + >; + }; + + i2c1_pins_default: pinmux_i2c1_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE2) /* I2C1_SDA_mux3 */ + AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE2) /* I2C1_SCL_mux3 */ + >; + }; + + i2c1_pins_gpio: pinmux_i2c1_pins_gpio { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT, MUX_MODE7) /* gpio0[4] */ + AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT, MUX_MODE7) /* gpio0[5] */ + >; + }; + + i2c1_pins_sleep: pinmux_i2c1_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + lcdc_pins_default: pinmux_lcdc_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0) /* lcd_data0 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0) /* lcd_data1 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0) /* lcd_data2 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0) /* lcd_data3 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0) /* lcd_data4 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0) /* lcd_data5 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0) /* lcd_data6 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0) /* lcd_data7 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0) /* lcd_data8 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0) /* lcd_data9 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0) /* lcd_data10 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0) /* lcd_data11 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0) /* lcd_data12 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0) /* lcd_data13 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0) /* lcd_data14 */ + AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0) /* lcd_data15 */ + AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT, MUX_MODE0) /* lcd_vsync */ + AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT, MUX_MODE0) /* lcd_hsync */ + AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT, MUX_MODE0) /* lcd_pclk */ + AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT, MUX_MODE0) /* lcd_ac_bias_en */ + >; + }; + + lcdc_pins_sleep: pinmux_lcdc_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PULL_DISABLE, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + leds_pins: pinmux_leds_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_OUTPUT, MUX_MODE7) /* gpio0[27] */ + AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE7) /* gpio0[3] */ + >; + }; + + mcasp0_pins_default: pinmux_mcasp0_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE0) /* mcasp0_aclkx_mux0 */ + AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE0) /* mcasp0_fsx_mux0 */ + AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT_PULLDOWN, MUX_MODE2) /* mcasp0_axr2_mux0 */ + AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_INPUT_PULLDOWN, MUX_MODE0) /* mcasp0_axr1_mux0 */ + >; + }; + + mcasp0_pins_sleep: pinmux_mcasp0_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + mmc1_pins_default: pinmux_mmc1_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0) /* mmc0_dat3 */ + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0) /* mmc0_dat2 */ + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0) /* mmc0_dat1 */ + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0) /* mmc0_dat0 */ + AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0) /* mmc0_clk */ + AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0) /* mmc0_cmd */ + AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE7) /* gpio3[21] */ + >; + }; + + mmc1_pins_sleep: pinmux_mmc1_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLDOWN, MUX_MODE0) + AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + uart0_pins: pinmux_uart0_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0) /* uart0_rxd */ + AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0) /* uart0_txd */ + >; + }; + + uart1_pins_default: pinmux_uart1_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0) /* uart1_rxd */ + AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0) /* uart1_txd */ + >; + }; + + uart1_pins_sleep: pinmux_uart1_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + uart2_pins_default: pinmux_uart2_pins_default { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT, MUX_MODE6) /* uart2_rxd_mux1 */ + AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_OUTPUT, MUX_MODE6) /* uart2_txd_mux1 */ + >; + }; + + uart2_pins_sleep: pinmux_uart2_pins_sleep { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7) + AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7) + >; + }; + + usb_pins: pinmux_usb_pins { + pinctrl-single,pins = < + AM33XX_PADCONF(AM335X_PIN_USB0_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0) /* USB0_DRVVBUS */ + AM33XX_PADCONF(AM335X_PIN_USB1_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0) /* USB1_DRVVBUS */ + >; + }; +}; From 28cc13e4060c62e87936bcbfd7a1313383d2a6d3 Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 26 Jan 2021 21:17:29 +0530 Subject: [PATCH 358/584] arm64: dts: qcom: sc7180: Add watchdog bark interrupt Specify bark interrupt for APSS watchdog to support pre-timeout notification on SC7180 SoC. Signed-off-by: Sai Prakash Ranjan Link: https://lore.kernel.org/r/535b368f6c22bab7078842d803a73e695f28a751.1611466260.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 2bd06beafecc..04445cd3cfd9 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -3349,6 +3349,7 @@ compatible = "qcom,apss-wdt-sc7180", "qcom,kpss-wdt"; reg = <0 0x17c10000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = ; }; timer@17c20000{ From 36c436b03c584ad9ecd7820ccdc4ae5ad76d79aa Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 26 Jan 2021 21:17:30 +0530 Subject: [PATCH 359/584] arm64: dts: qcom: sdm845: Add watchdog bark interrupt Specify bark interrupt for APSS watchdog to support pre-timeout notification on SDM845 SoC. Signed-off-by: Sai Prakash Ranjan Link: https://lore.kernel.org/r/7740e8ef57361d33da64e823b2356da2be0065b8.1611466260.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sdm845.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi index bcf888381f14..2da77e16f1b3 100644 --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi @@ -4573,6 +4573,7 @@ compatible = "qcom,apss-wdt-sdm845", "qcom,kpss-wdt"; reg = <0 0x17980000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = ; }; apss_shared: mailbox@17990000 { From b094c8f8dd2a01d5b537f68d41e6ef201de73259 Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 26 Jan 2021 21:17:31 +0530 Subject: [PATCH 360/584] arm64: dts: qcom: sm8150: Add watchdog bark interrupt Specify bark interrupt for APSS watchdog to support pre-timeout notification on SM8150 SoC. Signed-off-by: Sai Prakash Ranjan Link: https://lore.kernel.org/r/02700a5ac413bf5a7e3a0102233d1d64b47bb2cf.1611466260.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8150.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi index 9a939c6095ea..e5bb17bc2f46 100644 --- a/arch/arm64/boot/dts/qcom/sm8150.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi @@ -1975,6 +1975,7 @@ compatible = "qcom,apss-wdt-sm8150", "qcom,kpss-wdt"; reg = <0 0x17c10000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = ; }; timer@17c20000 { From 46a4359f9156f584bf5b17b8220ab6c59e861963 Mon Sep 17 00:00:00 2001 From: Sai Prakash Ranjan Date: Tue, 26 Jan 2021 21:17:32 +0530 Subject: [PATCH 361/584] arm64: dts: qcom: sm8250: Add watchdog bark interrupt Specify bark interrupt for APSS watchdog to support pre-timeout notification on SM8250 SoC. Signed-off-by: Sai Prakash Ranjan Link: https://lore.kernel.org/r/ff0758b158d62e82fd0636f5861115f435f821ac.1611466260.git.saiprakash.ranjan@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 20e70d5641ea..61191f7f5861 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -3289,6 +3289,7 @@ compatible = "qcom,apss-wdt-sm8250", "qcom,kpss-wdt"; reg = <0 0x17c10000 0 0x1000>; clocks = <&sleep_clk>; + interrupts = ; }; timer@17c20000 { From 88893986338beebcf5317bda80d43d4f6f7f7c7c Mon Sep 17 00:00:00 2001 From: Sowjanya Komatineni Date: Mon, 21 Dec 2020 13:17:31 -0800 Subject: [PATCH 362/584] dt-bindings: clock: tegra: Add clock ID TEGRA210_CLK_QSPI_PM Tegra210 QSPI clock output has divider DIV2_SEL which will be enabled when using DDR interface mode. This patch adds clock ID for this to dt-binding. Acked-by: Rob Herring Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding --- include/dt-bindings/clock/tegra210-car.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/include/dt-bindings/clock/tegra210-car.h b/include/dt-bindings/clock/tegra210-car.h index ab8b8a737a0a..9cfcc3baa52c 100644 --- a/include/dt-bindings/clock/tegra210-car.h +++ b/include/dt-bindings/clock/tegra210-car.h @@ -307,7 +307,7 @@ #define TEGRA210_CLK_AUDIO4 275 #define TEGRA210_CLK_SPDIF 276 /* 277 */ -/* 278 */ +#define TEGRA210_CLK_QSPI_PM 278 /* 279 */ /* 280 */ #define TEGRA210_CLK_SOR0_LVDS 281 /* deprecated */ From 1e0ca5467445bc1f41a9e403d6161a22f313dae7 Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Thu, 7 Jan 2021 10:36:10 +0530 Subject: [PATCH 363/584] arm64: tegra: Add power-domain for Tegra210 HDA HDA initialization is failing occasionally on Tegra210 and following print is observed in the boot log. Because of this probe() fails and no sound card is registered. [16.800802] tegra-hda 70030000.hda: no codecs found! Codecs request a state change and enumeration by the controller. In failure cases this does not seem to happen as STATETS register reads 0. The problem seems to be related to the HDA codec dependency on SOR power domain. If it is gated during HDA probe then the failure is observed. Building Tegra HDA driver into kernel image avoids this failure but does not completely address the dependency part. Fix this problem by adding 'power-domains' DT property for Tegra210 HDA. Note that Tegra186 and Tegra194 HDA do this already. Fixes: 742af7e7a0a1 ("arm64: tegra: Add Tegra210 support") Depends-on: 96d1f078ff0 ("arm64: tegra: Add SOR power-domain for Tegra210") Cc: Signed-off-by: Sameer Pujar Acked-by: Jon Hunter Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra210.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index 4fbf8c15b0a1..fd33b4d28ef3 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -997,6 +997,7 @@ <&tegra_car 128>, /* hda2hdmi */ <&tegra_car 111>; /* hda2codec_2x */ reset-names = "hda", "hda2hdmi", "hda2codec_2x"; + power-domains = <&pd_sor>; status = "disabled"; }; From 4ff5e30d8bd96b186c95aab6f3cdafbea4630bd7 Mon Sep 17 00:00:00 2001 From: JC Kuo Date: Wed, 20 Jan 2021 15:34:08 +0800 Subject: [PATCH 364/584] arm64: tegra: Add XUSB pad controller's "nvidia,pmc" property on Tegra210 PMC driver provides USB sleepwalk registers access to XUSB PADCTL driver. This commit adds a "nvidia,pmc" property which points to PMC node to XUSB PADCTL device node. Signed-off-by: JC Kuo Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra210.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index fd33b4d28ef3..727916343013 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -1044,6 +1044,7 @@ interrupts = ; resets = <&tegra_car 142>; reset-names = "padctl"; + nvidia,pmc = <&tegra_pmc>; status = "disabled"; From 40b4d824ad22e5f55c4725eea5591fc6c4b5f5d0 Mon Sep 17 00:00:00 2001 From: JC Kuo Date: Tue, 19 Jan 2021 10:23:49 +0800 Subject: [PATCH 365/584] arm64: tegra: Enable Jetson-Xavier J512 USB host This commit enables USB host mode at J512 type-C port of Jetson-Xavier. Signed-off-by: JC Kuo Acked-by: Jon Hunter Tested-by: Jon Hunter Signed-off-by: Thierry Reding --- .../arm64/boot/dts/nvidia/tegra194-p2888.dtsi | 8 +++++++ .../boot/dts/nvidia/tegra194-p2972-0000.dts | 24 +++++++++++++++++-- 2 files changed, 30 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi index d71b7a1140fe..7e7b0eb90c80 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi @@ -93,6 +93,10 @@ vclamp-usb-supply = <&vdd_1v8ao>; ports { + usb2-0 { + vbus-supply = <&vdd_5v0_sys>; + }; + usb2-1 { vbus-supply = <&vdd_5v0_sys>; }; @@ -105,6 +109,10 @@ vbus-supply = <&vdd_5v0_sys>; }; + usb3-2 { + vbus-supply = <&vdd_5v0_sys>; + }; + usb3-3 { vbus-supply = <&vdd_5v0_sys>; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts index 54d057beec59..8697927b1fe7 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts @@ -57,6 +57,10 @@ pads { usb2 { lanes { + usb2-0 { + status = "okay"; + }; + usb2-1 { status = "okay"; }; @@ -73,6 +77,10 @@ status = "okay"; }; + usb3-2 { + status = "okay"; + }; + usb3-3 { status = "okay"; }; @@ -81,6 +89,11 @@ }; ports { + usb2-0 { + mode = "host"; + status = "okay"; + }; + usb2-1 { mode = "host"; status = "okay"; @@ -96,6 +109,11 @@ status = "okay"; }; + usb3-2 { + nvidia,usb2-companion = <0>; + status = "okay"; + }; + usb3-3 { nvidia,usb2-companion = <3>; maximum-speed = "super-speed"; @@ -107,11 +125,13 @@ usb@3610000 { status = "okay"; - phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, + phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-0}>, + <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-3}>, <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-0}>, + <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-2}>, <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-3}>; - phy-names = "usb2-1", "usb2-3", "usb3-0", "usb3-3"; + phy-names = "usb2-0", "usb2-1", "usb2-3", "usb3-0", "usb3-2", "usb3-3"; }; pwm@c340000 { From 38254d1976b80f546fc82f14a386be6f70e9b0dd Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Mon, 25 Jan 2021 16:32:56 +0100 Subject: [PATCH 366/584] arm64: tegra: Order nodes alphabetically on Tegra210 Device tree nodes are ordered by unit-address and alphabetically by name if a node doesn't have a unit-address. The thermal sensor and timer nodes were not sorted in the correct order, so do that now. Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra210.dtsi | 80 ++++++++++++------------ 1 file changed, 40 insertions(+), 40 deletions(-) diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index 727916343013..c0b25ac1b103 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -1309,6 +1309,32 @@ status = "disabled"; }; + soctherm: thermal-sensor@700e2000 { + compatible = "nvidia,tegra210-soctherm"; + reg = <0x0 0x700e2000 0x0 0x600>, /* SOC_THERM reg_base */ + <0x0 0x60006000 0x0 0x400>; /* CAR reg_base */ + reg-names = "soctherm-reg", "car-reg"; + interrupts = , + ; + interrupt-names = "thermal", "edp"; + clocks = <&tegra_car TEGRA210_CLK_TSENSOR>, + <&tegra_car TEGRA210_CLK_SOC_THERM>; + clock-names = "tsensor", "soctherm"; + resets = <&tegra_car 78>; + reset-names = "soctherm"; + #thermal-sensor-cells = <1>; + + throttle-cfgs { + throttle_heavy: heavy { + nvidia,priority = <100>; + nvidia,cpu-throt-percent = <85>; + nvidia,gpu-throt-level = ; + + #cooling-cells = <2>; + }; + }; + }; + mipi: mipi@700e3000 { compatible = "nvidia,tegra210-mipi"; reg = <0x0 0x700e3000 0x0 0x100>; @@ -1694,46 +1720,6 @@ &{/cpus/cpu@2} &{/cpus/cpu@3}>; }; - timer { - compatible = "arm,armv8-timer"; - interrupts = , - , - , - ; - interrupt-parent = <&gic>; - arm,no-tick-in-suspend; - }; - - soctherm: thermal-sensor@700e2000 { - compatible = "nvidia,tegra210-soctherm"; - reg = <0x0 0x700e2000 0x0 0x600>, /* SOC_THERM reg_base */ - <0x0 0x60006000 0x0 0x400>; /* CAR reg_base */ - reg-names = "soctherm-reg", "car-reg"; - interrupts = , - ; - interrupt-names = "thermal", "edp"; - clocks = <&tegra_car TEGRA210_CLK_TSENSOR>, - <&tegra_car TEGRA210_CLK_SOC_THERM>; - clock-names = "tsensor", "soctherm"; - resets = <&tegra_car 78>; - reset-names = "soctherm"; - #thermal-sensor-cells = <1>; - - throttle-cfgs { - throttle_heavy: heavy { - nvidia,priority = <100>; - nvidia,cpu-throt-percent = <85>; - nvidia,gpu-throt-level = ; - - #cooling-cells = <2>; - }; - }; - }; - thermal-zones { cpu { polling-delay-passive = <1000>; @@ -1868,4 +1854,18 @@ }; }; }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = , + , + , + ; + interrupt-parent = <&gic>; + arm,no-tick-in-suspend; + }; }; From f5208672eba03a1f4736fdd95d8be688012f1b06 Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Tue, 19 Jan 2021 14:58:15 +0530 Subject: [PATCH 367/584] arm64: tegra: Audio graph header for Tegra210 Expose a header which describes DT bindings required to use audio-graph based sound card. All Tegra210 based platforms can include this header and add platform specific information. Currently, from SoC point of view, all links are exposed for ADMAIF, AHUB, I2S and DMIC components. Signed-off-by: Sameer Pujar Reviewed-by: Jon Hunter Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra210.dtsi | 182 +++++++++++++++++++++++ 1 file changed, 182 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index c0b25ac1b103..6e6cdb229e01 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -1453,6 +1453,91 @@ "rx9", "tx9", "rx10", "tx10"; status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + admaif1_port: port@0 { + reg = <0>; + + admaif1_ep: endpoint { + remote-endpoint = <&xbar_admaif1_ep>; + }; + }; + + admaif2_port: port@1 { + reg = <1>; + + admaif2_ep: endpoint { + remote-endpoint = <&xbar_admaif2_ep>; + }; + }; + + admaif3_port: port@2 { + reg = <2>; + + admaif3_ep: endpoint { + remote-endpoint = <&xbar_admaif3_ep>; + }; + }; + + admaif4_port: port@3 { + reg = <3>; + + admaif4_ep: endpoint { + remote-endpoint = <&xbar_admaif4_ep>; + }; + }; + + admaif5_port: port@4 { + reg = <4>; + + admaif5_ep: endpoint { + remote-endpoint = <&xbar_admaif5_ep>; + }; + }; + + admaif6_port: port@5 { + reg = <5>; + + admaif6_ep: endpoint { + remote-endpoint = <&xbar_admaif6_ep>; + }; + }; + + admaif7_port: port@6 { + reg = <6>; + + admaif7_ep: endpoint { + remote-endpoint = <&xbar_admaif7_ep>; + }; + }; + + admaif8_port: port@7 { + reg = <7>; + + admaif8_ep: endpoint { + remote-endpoint = <&xbar_admaif8_ep>; + }; + }; + + admaif9_port: port@8 { + reg = <8>; + + admaif9_ep: endpoint { + remote-endpoint = <&xbar_admaif9_ep>; + }; + }; + + admaif10_port: port@9 { + reg = <9>; + + admaif10_ep: endpoint { + remote-endpoint = <&xbar_admaif10_ep>; + }; + }; + }; }; tegra_i2s1: i2s@702d1000 { @@ -1555,6 +1640,89 @@ sound-name-prefix = "DMIC3"; status = "disabled"; }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + + xbar_admaif1_ep: endpoint { + remote-endpoint = <&admaif1_ep>; + }; + }; + + port@1 { + reg = <0x1>; + + xbar_admaif2_ep: endpoint { + remote-endpoint = <&admaif2_ep>; + }; + }; + + port@2 { + reg = <0x2>; + + xbar_admaif3_ep: endpoint { + remote-endpoint = <&admaif3_ep>; + }; + }; + + port@3 { + reg = <0x3>; + + xbar_admaif4_ep: endpoint { + remote-endpoint = <&admaif4_ep>; + }; + }; + + port@4 { + reg = <0x4>; + xbar_admaif5_ep: endpoint { + remote-endpoint = <&admaif5_ep>; + }; + }; + port@5 { + reg = <0x5>; + + xbar_admaif6_ep: endpoint { + remote-endpoint = <&admaif6_ep>; + }; + }; + + port@6 { + reg = <0x6>; + + xbar_admaif7_ep: endpoint { + remote-endpoint = <&admaif7_ep>; + }; + }; + + port@7 { + reg = <0x7>; + + xbar_admaif8_ep: endpoint { + remote-endpoint = <&admaif8_ep>; + }; + }; + + port@8 { + reg = <0x8>; + + xbar_admaif9_ep: endpoint { + remote-endpoint = <&admaif9_ep>; + }; + }; + + port@9 { + reg = <0x9>; + + xbar_admaif10_ep: endpoint { + remote-endpoint = <&admaif10_ep>; + }; + }; + }; }; }; @@ -1720,6 +1888,20 @@ &{/cpus/cpu@2} &{/cpus/cpu@3}>; }; + sound { + status = "disabled"; + + clocks = <&tegra_car TEGRA210_CLK_PLL_A>, + <&tegra_car TEGRA210_CLK_PLL_A_OUT0>; + clock-names = "pll_a", "plla_out0"; + + assigned-clocks = <&tegra_car TEGRA210_CLK_PLL_A>, + <&tegra_car TEGRA210_CLK_PLL_A_OUT0>, + <&tegra_car TEGRA210_CLK_EXTERN1>; + assigned-clock-parents = <0>, <0>, <&tegra_car TEGRA210_CLK_PLL_A_OUT0>; + assigned-clock-rates = <368640000>, <49152000>, <12288000>; + }; + thermal-zones { cpu { polling-delay-passive = <1000>; From b0b4e286f9aa97faeea3d54469bc5b042ee1f518 Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Tue, 19 Jan 2021 14:58:16 +0530 Subject: [PATCH 368/584] arm64: tegra: Audio graph sound card for Jetson Nano and TX1 Enable support for audio-graph based sound card on Jetson-Nano and Jetson-TX1. Depending on the platform, required I/O interfaces are enabled. * Jetson-Nano: Enable I2S3, I2S4, DMIC1 and DMIC2. * Jetson-TX1: Enable all I2S and DMIC interfaces. Signed-off-by: Sameer Pujar Reviewed-by: Jon Hunter Signed-off-by: Thierry Reding --- .../boot/dts/nvidia/tegra210-p2371-2180.dts | 299 ++++++++++++++++++ .../boot/dts/nvidia/tegra210-p3450-0000.dts | 163 ++++++++++ 2 files changed, 462 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts index 69102dcea8b0..497635af7fab 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts @@ -126,5 +126,304 @@ interrupt-controller@702f9000 { status = "okay"; }; + + ahub@702d0800 { + status = "okay"; + + admaif@702d0000 { + status = "okay"; + }; + + i2s@702d1000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s1_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s1_ep>; + }; + }; + + i2s1_port: port@1 { + reg = <1>; + + i2s1_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s2_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s2_ep>; + }; + }; + + i2s2_port: port@1 { + reg = <1>; + + i2s2_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s3_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s3_ep>; + }; + }; + + i2s3_port: port@1 { + reg = <1>; + + i2s3_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1400 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s5_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s5_ep>; + }; + }; + + i2s5_port: port@1 { + reg = <1>; + + i2s5_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic1_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic1_ep>; + }; + }; + + dmic1_port: port@1 { + reg = <1>; + + dmic1_dap_ep: endpoint { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic2_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic2_ep>; + }; + }; + + dmic2_port: port@1 { + reg = <1>; + + dmic2_dap_ep: endpoint { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic3_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic3_ep>; + }; + }; + + dmic3_port: port@1 { + reg = <1>; + + dmic3_dap_ep: endpoint { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + ports { + xbar_i2s1_port: port@a { + reg = <0xa>; + + xbar_i2s1_ep: endpoint { + remote-endpoint = <&i2s1_cif_ep>; + }; + }; + + xbar_i2s2_port: port@b { + reg = <0xb>; + + xbar_i2s2_ep: endpoint { + remote-endpoint = <&i2s2_cif_ep>; + }; + }; + + xbar_i2s3_port: port@c { + reg = <0xc>; + + xbar_i2s3_ep: endpoint { + remote-endpoint = <&i2s3_cif_ep>; + }; + }; + + xbar_i2s4_port: port@d { + reg = <0xd>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_i2s5_port: port@e { + reg = <0xe>; + + xbar_i2s5_ep: endpoint { + remote-endpoint = <&i2s5_cif_ep>; + }; + }; + + xbar_dmic1_port: port@f { + reg = <0xf>; + + xbar_dmic1_ep: endpoint { + remote-endpoint = <&dmic1_cif_ep>; + }; + }; + + xbar_dmic2_port: port@10 { + reg = <0x10>; + + xbar_dmic2_ep: endpoint { + remote-endpoint = <&dmic2_cif_ep>; + }; + }; + + xbar_dmic3_port: port@11 { + reg = <0x11>; + + xbar_dmic3_ep: endpoint { + remote-endpoint = <&dmic3_cif_ep>; + }; + }; + }; + }; + }; + + sound { + compatible = "nvidia,tegra210-audio-graph-card"; + status = "okay"; + + dais = /* FE */ + <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, + <&admaif7_port>, <&admaif8_port>, <&admaif9_port>, + <&admaif10_port>, + /* Router */ + <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s3_port>, + <&xbar_i2s4_port>, <&xbar_i2s5_port>, <&xbar_dmic1_port>, + <&xbar_dmic2_port>, <&xbar_dmic3_port>, + /* I/O DAP Ports */ + <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>, + <&i2s5_port>, <&dmic1_port>, <&dmic2_port>, <&dmic3_port>; + + label = "jetson-tx1-ape"; }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts index 6a877decffc1..1170f33f46d5 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts @@ -636,6 +636,150 @@ interrupt-controller@702f9000 { status = "okay"; }; + + ahub@702d0800 { + status = "okay"; + + admaif@702d0000 { + status = "okay"; + }; + + i2s@702d1200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s3_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s3_ep>; + }; + }; + + i2s3_port: port@1 { + reg = <1>; + + i2s3_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@702d1300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint@0 { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic1_cif_ep: endpoint@0 { + remote-endpoint = <&xbar_dmic1_ep>; + }; + }; + + dmic1_port: port@1 { + reg = <1>; + + dmic1_dap_ep: endpoint@0 { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@702d4100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic2_cif_ep: endpoint@0 { + remote-endpoint = <&xbar_dmic2_ep>; + }; + }; + + dmic2_port: port@1 { + reg = <1>; + + dmic2_dap_ep: endpoint@0 { + /* Placeholder for external Codec */ + }; + }; + }; + }; + + ports { + xbar_i2s3_port: port@c { + reg = <0xc>; + + xbar_i2s3_ep: endpoint { + remote-endpoint = <&i2s3_cif_ep>; + }; + }; + + xbar_i2s4_port: port@d { + reg = <0xd>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_dmic1_port: port@f { + reg = <0xf>; + + xbar_dmic1_ep: endpoint { + remote-endpoint = <&dmic1_cif_ep>; + }; + }; + + xbar_dmic2_port: port@10 { + reg = <0x10>; + + xbar_dmic2_ep: endpoint { + remote-endpoint = <&dmic2_cif_ep>; + }; + }; + }; + }; }; clk32k_in: clock@0 { @@ -870,4 +1014,23 @@ vin-supply = <&vdd_5v0_sys>; }; + + sound { + compatible = "nvidia,tegra210-audio-graph-card"; + status = "okay"; + + dais = /* FE */ + <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, + <&admaif7_port>, <&admaif8_port>, <&admaif9_port>, + <&admaif10_port>, + /* Router */ + <&xbar_i2s3_port>, <&xbar_i2s4_port>, + <&xbar_dmic1_port>, <&xbar_dmic2_port>, + /* I/O DAP Ports */ + <&i2s3_port>, <&i2s4_port>, + <&dmic1_port>, <&dmic2_port>; + + label = "jetson-nano-ape"; + }; }; From 07910a79fc340881eb8e3ed9e47654574fa83d3f Mon Sep 17 00:00:00 2001 From: Sowjanya Komatineni Date: Mon, 21 Dec 2020 13:17:37 -0800 Subject: [PATCH 369/584] arm64: tegra: Enable QSPI on Jetson Nano This patch enables QSPI on Jetson Nano. Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts | 12 ++++++++++++ arch/arm64/boot/dts/nvidia/tegra210.dtsi | 5 +++-- 2 files changed, 15 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts index 1170f33f46d5..14c128a5e248 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts @@ -782,6 +782,18 @@ }; }; + spi@70410000 { + status = "okay"; + + flash@0 { + compatible = "spi-nor"; + reg = <0>; + spi-max-frequency = <104000000>; + spi-tx-bus-width = <2>; + spi-rx-bus-width = <2>; + }; + }; + clk32k_in: clock@0 { compatible = "fixed-clock"; clock-frequency = <32768>; diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi index 6e6cdb229e01..26b3f98a211c 100644 --- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi @@ -1732,8 +1732,9 @@ interrupts = ; #address-cells = <1>; #size-cells = <0>; - clocks = <&tegra_car TEGRA210_CLK_QSPI>; - clock-names = "qspi"; + clocks = <&tegra_car TEGRA210_CLK_QSPI>, + <&tegra_car TEGRA210_CLK_QSPI_PM>; + clock-names = "qspi", "qspi_out"; resets = <&tegra_car 211>; reset-names = "qspi"; dmas = <&apbdma 5>, <&apbdma 5>; From 96ded827a2e8da0ac74ea92d1eb5ebd9e22c2724 Mon Sep 17 00:00:00 2001 From: Sowjanya Komatineni Date: Mon, 21 Dec 2020 13:17:38 -0800 Subject: [PATCH 370/584] arm64: tegra: Add QSPI nodes on Tegra194 Tegra194 has 2 QSPI controllers. This patch adds DT node for these 2 QSPI controllers. Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra194.dtsi | 28 ++++++++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi index 25f36d6118f8..852980fe0d35 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi @@ -609,6 +609,34 @@ status = "disabled"; }; + spi@3270000 { + compatible = "nvidia,tegra194-qspi"; + reg = <0x3270000 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bpmp TEGRA194_CLK_QSPI0>, + <&bpmp TEGRA194_CLK_QSPI0_PM>; + clock-names = "qspi", "qspi_out"; + resets = <&bpmp TEGRA194_RESET_QSPI0>; + reset-names = "qspi"; + status = "disabled"; + }; + + spi@3300000 { + compatible = "nvidia,tegra194-qspi"; + reg = <0x3300000 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bpmp TEGRA194_CLK_QSPI1>, + <&bpmp TEGRA194_CLK_QSPI1_PM>; + clock-names = "qspi", "qspi_out"; + resets = <&bpmp TEGRA194_RESET_QSPI1>; + reset-names = "qspi"; + status = "disabled"; + }; + pwm1: pwm@3280000 { compatible = "nvidia,tegra194-pwm", "nvidia,tegra186-pwm"; From ad338c2d69ecd45c39ff218cf219658affda9336 Mon Sep 17 00:00:00 2001 From: Sowjanya Komatineni Date: Mon, 21 Dec 2020 13:17:39 -0800 Subject: [PATCH 371/584] arm64: tegra: Enable QSPI on Jetson Xavier NX This patch enables QSPI on Jetson Xavier NX. Signed-off-by: Sowjanya Komatineni Signed-off-by: Thierry Reding --- .../dts/nvidia/tegra194-p3509-0000+p3668-0000.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts index 7f97b34216a0..f1053e7be45c 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts @@ -100,6 +100,18 @@ phy-names = "usb2-1", "usb2-2", "usb3-2"; }; + spi@3270000 { + status = "okay"; + + flash@0 { + compatible = "spi-nor"; + reg = <0>; + spi-max-frequency = <102000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; + }; + pwm@32d0000 { status = "okay"; }; From 527a3ac9bdf81da4b7160ce3cea57f28a0e5eb64 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Wed, 13 Jan 2021 12:14:06 +0100 Subject: [PATCH 372/584] arm64: dts: broadcom: bcm4908: describe internal switch MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit BCM4908 has internal switch with 5 GPHYs. Ports 0 - 3 are always connected to the internal PHYs. Remaining ports depend on device setup. Asus GT-AC5300 has an extra switch with its PHYs accessible using the internal MDIO. CPU port and Ethernet interface remain to be documented. Signed-off-by: RafaÅ‚ MiÅ‚ecki Signed-off-by: Florian Fainelli --- .../bcm4908/bcm4908-asus-gt-ac5300.dts | 51 +++++++++++ .../boot/dts/broadcom/bcm4908/bcm4908.dtsi | 85 ++++++++++++++++++- 2 files changed, 135 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts index 13c6b86eef21..6e4ad66ff536 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts @@ -44,6 +44,57 @@ }; }; +&ports { + port@0 { + label = "lan2"; + }; + + port@1 { + label = "lan1"; + }; + + port@2 { + label = "lan6"; + }; + + port@3 { + label = "lan5"; + }; + + /* External BCM53134S switch */ + port@7 { + label = "sw"; + reg = <7>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; +}; + +&mdio { + /* lan8 */ + ethernet-phy@0 { + reg = <0>; + }; + + /* lan7 */ + ethernet-phy@1 { + reg = <1>; + }; + + /* lan4 */ + ethernet-phy@2 { + reg = <2>; + }; + + /* lan3 */ + ethernet-phy@3 { + reg = <3>; + }; +}; + &nandcs { nand-ecc-strength = <4>; nand-ecc-step-size = <512>; diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi index b5b772a9a51b..3fa01886f3a1 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi @@ -108,7 +108,7 @@ compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; - ranges = <0x00 0x00 0x80000000 0x10000>; + ranges = <0x00 0x00 0x80000000 0xd0000>; usb@c300 { compatible = "generic-ehci"; @@ -130,6 +130,89 @@ interrupts = ; status = "disabled"; }; + + ethernet-switch@80000 { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0 0x80000 0x50000>; + + ethernet-switch@0 { + compatible = "brcm,bcm4908-switch"; + reg = <0x0 0x40000>, + <0x40000 0x110>, + <0x40340 0x30>, + <0x40380 0x30>, + <0x40600 0x34>, + <0x40800 0x208>; + reg-names = "core", "reg", "intrl2_0", + "intrl2_1", "fcb", "acb"; + interrupts = , + ; + brcm,num-gphy = <5>; + brcm,num-rgmii-ports = <2>; + + #address-cells = <1>; + #size-cells = <0>; + + ports: ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + phy-mode = "internal"; + phy-handle = <&phy8>; + }; + + port@1 { + reg = <1>; + phy-mode = "internal"; + phy-handle = <&phy9>; + }; + + port@2 { + reg = <2>; + phy-mode = "internal"; + phy-handle = <&phy10>; + }; + + port@3 { + reg = <3>; + phy-mode = "internal"; + phy-handle = <&phy11>; + }; + }; + }; + + mdio: mdio@405c0 { + compatible = "brcm,unimac-mdio"; + reg = <0x405c0 0x8>; + reg-names = "mdio"; + #size-cells = <0>; + #address-cells = <1>; + + phy8: ethernet-phy@8 { + reg = <8>; + }; + + phy9: ethernet-phy@9 { + reg = <9>; + }; + + phy10: ethernet-phy@a { + reg = <10>; + }; + + phy11: ethernet-phy@b { + reg = <11>; + }; + + phy12: ethernet-phy@c { + reg = <12>; + }; + }; + }; }; bus@ff800000 { From 7a31889ef0f9db005564eb99c584e8de4fd075e1 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rafa=C5=82=20Mi=C5=82ecki?= Date: Wed, 13 Jan 2021 12:15:47 +0100 Subject: [PATCH 373/584] arm64: dts: broadcom: bcm4908: describe PMB block MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit PMB (Power Management Bus) controls powering connected devices (e.g. PCIe, USB, SATA). In BCM4908 it's a part of the PROCMON block. Signed-off-by: RafaÅ‚ MiÅ‚ecki Signed-off-by: Florian Fainelli --- .../boot/dts/broadcom/bcm4908/bcm4908.dtsi | 17 ++++++++++++++++- 1 file changed, 16 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi index 3fa01886f3a1..9354077f74cd 100644 --- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi +++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi @@ -108,7 +108,7 @@ compatible = "simple-bus"; #address-cells = <1>; #size-cells = <1>; - ranges = <0x00 0x00 0x80000000 0xd0000>; + ranges = <0x00 0x00 0x80000000 0x281000>; usb@c300 { compatible = "generic-ehci"; @@ -213,6 +213,21 @@ }; }; }; + + procmon: syscon@280000 { + compatible = "simple-bus"; + reg = <0x280000 0x1000>; + ranges; + + #address-cells = <1>; + #size-cells = <1>; + + power-controller@2800c0 { + compatible = "brcm,bcm4908-pmb"; + reg = <0x2800c0 0x40>; + #power-domain-cells = <1>; + }; + }; }; bus@ff800000 { From fe119977677e7dd3ddb4ab52678b46b804148eb5 Mon Sep 17 00:00:00 2001 From: Scott Branden Date: Wed, 20 Jan 2021 10:51:40 -0800 Subject: [PATCH 374/584] arm64: dts: broadcom: Remove SATA from Stingray Remove SATA from Stingray as it is unsupported. Acked-by: Ray Jui Signed-off-by: Scott Branden Signed-off-by: Florian Fainelli --- .../dts/broadcom/stingray/bcm958742-base.dtsi | 64 ---- .../dts/broadcom/stingray/stingray-sata.dtsi | 278 ------------------ .../boot/dts/broadcom/stingray/stingray.dtsi | 7 - 3 files changed, 349 deletions(-) delete mode 100644 arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi index 43aa5e9c0020..8fe7325cfbb2 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742-base.dtsi @@ -56,70 +56,6 @@ }; }; -&sata0 { - status = "okay"; -}; - -&sata_phy0{ - status = "okay"; -}; - -&sata1 { - status = "okay"; -}; - -&sata_phy1{ - status = "okay"; -}; - -&sata2 { - status = "okay"; -}; - -&sata_phy2{ - status = "okay"; -}; - -&sata3 { - status = "okay"; -}; - -&sata_phy3{ - status = "okay"; -}; - -&sata4 { - status = "okay"; -}; - -&sata_phy4{ - status = "okay"; -}; - -&sata5 { - status = "okay"; -}; - -&sata_phy5{ - status = "okay"; -}; - -&sata6 { - status = "okay"; -}; - -&sata_phy6{ - status = "okay"; -}; - -&sata7 { - status = "okay"; -}; - -&sata_phy7{ - status = "okay"; -}; - &pwm { status = "okay"; }; diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi deleted file mode 100644 index 8c68e0c26f1b..000000000000 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray-sata.dtsi +++ /dev/null @@ -1,278 +0,0 @@ -/* - * BSD LICENSE - * - * Copyright(c) 2016-2017 Broadcom. All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * - * * Redistributions of source code must retain the above copyright - * notice, this list of conditions and the following disclaimer. - * * Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in - * the documentation and/or other materials provided with the - * distribution. - * * Neither the name of Broadcom nor the names of its - * contributors may be used to endorse or promote products derived - * from this software without specific prior written permission. - * - * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS - * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT - * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR - * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT - * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, - * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT - * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, - * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY - * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT - * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE - * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. - */ - - sata { - compatible = "simple-bus"; - #address-cells = <1>; - #size-cells = <1>; - ranges = <0x0 0x0 0x67d00000 0x00800000>; - - sata0: ahci@0 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00000000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata0_port0: sata-port@0 { - reg = <0>; - phys = <&sata0_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy0: sata_phy@2100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00002100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata0_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata1: ahci@10000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00010000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata1_port0: sata-port@0 { - reg = <0>; - phys = <&sata1_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy1: sata_phy@12100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00012100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata1_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata2: ahci@20000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00020000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata2_port0: sata-port@0 { - reg = <0>; - phys = <&sata2_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy2: sata_phy@22100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00022100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata2_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata3: ahci@30000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00030000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata3_port0: sata-port@0 { - reg = <0>; - phys = <&sata3_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy3: sata_phy@32100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00032100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata3_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata4: ahci@100000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00100000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata4_port0: sata-port@0 { - reg = <0>; - phys = <&sata4_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy4: sata_phy@102100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00102100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata4_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata5: ahci@110000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00110000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata5_port0: sata-port@0 { - reg = <0>; - phys = <&sata5_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy5: sata_phy@112100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00112100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata5_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata6: ahci@120000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00120000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata6_port0: sata-port@0 { - reg = <0>; - phys = <&sata6_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy6: sata_phy@122100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00122100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata6_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - - sata7: ahci@130000 { - compatible = "brcm,iproc-ahci", "generic-ahci"; - reg = <0x00130000 0x1000>; - reg-names = "ahci"; - interrupts = ; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata7_port0: sata-port@0 { - reg = <0>; - phys = <&sata7_phy0>; - phy-names = "sata-phy"; - }; - }; - - sata_phy7: sata_phy@132100 { - compatible = "brcm,iproc-sr-sata-phy"; - reg = <0x00132100 0x1000>; - reg-names = "phy"; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - - sata7_phy0: sata-phy@0 { - reg = <0>; - #phy-cells = <0>; - }; - }; - }; diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi index b425b12c3ed2..2ffb2c92182a 100644 --- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi +++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi @@ -285,7 +285,6 @@ }; #include "stingray-fs4.dtsi" - #include "stingray-sata.dtsi" #include "stingray-pcie.dtsi" #include "stingray-usb.dtsi" @@ -309,12 +308,6 @@ #size-cells = <0>; }; - mdio@2 { /* SATA */ - reg = <0x2>; - #address-cells = <1>; - #size-cells = <0>; - }; - mdio@3 { /* USB */ reg = <0x3>; #address-cells = <1>; From e2b539707aeaba45574bb6532d2d0c804a8bfeac Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Mon, 11 Jan 2021 15:23:09 +0100 Subject: [PATCH 375/584] ARM: dts: bcm2711: Add the CEC interrupt controller The CEC and hotplug interrupts go through an interrupt controller shared between the two HDMI controllers. Let's add that interrupt controller and the interrupts for both HDMI controllers Reviewed-by: Florian Fainelli Signed-off-by: Maxime Ripard Signed-off-by: Nicolas Saenz Julienne Link: https://lore.kernel.org/r/20210111142309.193441-16-maxime@cerno.tech --- arch/arm/boot/dts/bcm2711.dtsi | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi index d84e731799b3..462b1dfb0385 100644 --- a/arch/arm/boot/dts/bcm2711.dtsi +++ b/arch/arm/boot/dts/bcm2711.dtsi @@ -316,6 +316,14 @@ #interrupt-cells = <1>; }; + aon_intr: interrupt-controller@7ef00100 { + compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc"; + reg = <0x7ef00100 0x30>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <1>; + }; + hdmi0: hdmi@7ef00700 { compatible = "brcm,bcm2711-hdmi0"; reg = <0x7ef00700 0x300>, @@ -338,6 +346,11 @@ "hd"; clock-names = "hdmi", "bvb", "audio", "cec"; resets = <&dvp 0>; + interrupt-parent = <&aon_intr>; + interrupts = <0>, <1>, <2>, + <3>, <4>, <5>; + interrupt-names = "cec-tx", "cec-rx", "cec-low", + "wakeup", "hpd-connected", "hpd-removed"; ddc = <&ddc0>; dmas = <&dma 10>; dma-names = "audio-rx"; @@ -377,6 +390,11 @@ ddc = <&ddc1>; clock-names = "hdmi", "bvb", "audio", "cec"; resets = <&dvp 1>; + interrupt-parent = <&aon_intr>; + interrupts = <8>, <7>, <6>, + <9>, <10>, <11>; + interrupt-names = "cec-tx", "cec-rx", "cec-low", + "wakeup", "hpd-connected", "hpd-removed"; dmas = <&dma 17>; dma-names = "audio-rx"; status = "disabled"; From ae10ce938da59c19f303a91197ea7d664d1bc080 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Wed, 20 Jan 2021 13:51:45 -0600 Subject: [PATCH 376/584] arm64: dts: ti: k3*: Fixup PMU compatibility to be CPU specific We can use CPU specific pmu configuration to expose the appropriate CPU specific events rather than just the basic generic pmuv3 perf events. Reported-by: Sudeep Holla Signed-off-by: Nishanth Menon Tested-by: Suman Anna Reviewed-by: Tero Kristo Link: https://lore.kernel.org/r/20210120195145.32259-1-nm@ti.com --- arch/arm64/boot/dts/ti/k3-am65.dtsi | 2 +- arch/arm64/boot/dts/ti/k3-j7200.dtsi | 2 +- arch/arm64/boot/dts/ti/k3-j721e.dtsi | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) diff --git a/arch/arm64/boot/dts/ti/k3-am65.dtsi b/arch/arm64/boot/dts/ti/k3-am65.dtsi index d84c0bc05023..a9fc1af03f27 100644 --- a/arch/arm64/boot/dts/ti/k3-am65.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am65.dtsi @@ -56,7 +56,7 @@ }; pmu: pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a53-pmu"; /* Recommendation from GIC500 TRM Table A.3 */ interrupts = ; }; diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi index 66169bcf7c9a..b7005b803149 100644 --- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi @@ -114,7 +114,7 @@ }; pmu: pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a72-pmu"; interrupts = ; }; diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi index cc483f7344af..f0587fde147e 100644 --- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi @@ -115,7 +115,7 @@ }; pmu: pmu { - compatible = "arm,armv8-pmuv3"; + compatible = "arm,cortex-a72-pmu"; /* Recommendation from GIC500 TRM Table A.3 */ interrupts = ; }; From 431368c2648b59e5485a1b5f1276a83d885fb44b Mon Sep 17 00:00:00 2001 From: Yongqiang Niu Date: Thu, 28 Jan 2021 19:23:07 +0800 Subject: [PATCH 377/584] arm64: dts: mt8183: rename rdma fifo size property name must include only lowercase and '-' Fixes: 91f9c963ce79 ("arm64: dts: mt8183: Add display nodes for MT8183") Signed-off-by: Yongqiang Niu Signed-off-by: Hsin-Yi Wang Reviewed-by: Chun-Kuang Hu Reviewed-by: Enric Balletbo i Serra Link: https://lore.kernel.org/r/20210128112314.1304160-2-hsinyi@chromium.org Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index 5b782a4769e7..6c84ccb709af 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -1011,7 +1011,7 @@ clocks = <&mmsys CLK_MM_DISP_RDMA0>; iommus = <&iommu M4U_PORT_DISP_RDMA0>; mediatek,larb = <&larb0>; - mediatek,rdma_fifo_size = <5120>; + mediatek,rdma-fifo-size = <5120>; mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xb000 0x1000>; }; @@ -1023,7 +1023,7 @@ clocks = <&mmsys CLK_MM_DISP_RDMA1>; iommus = <&iommu M4U_PORT_DISP_RDMA1>; mediatek,larb = <&larb0>; - mediatek,rdma_fifo_size = <2048>; + mediatek,rdma-fifo-size = <2048>; mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xc000 0x1000>; }; From 9a2cb5eba7ad4fa7ccb3a4aa754f5263111e8f96 Mon Sep 17 00:00:00 2001 From: Yongqiang Niu Date: Thu, 28 Jan 2021 19:23:08 +0800 Subject: [PATCH 378/584] arm64: dts: mt8183: refine gamma compatible name mt8183 gamma is different with mt8173 remove mt8173 compatible name for mt8183 gamma Fixes: 91f9c963ce79 ("arm64: dts: mt8183: Add display nodes for MT8183") Signed-off-by: Yongqiang Niu Signed-off-by: Hsin-Yi Wang Reviewed-by: Enric Balletbo i Serra Link: https://lore.kernel.org/r/20210128112314.1304160-3-hsinyi@chromium.org Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index 6c84ccb709af..9c0073cfad45 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -1055,8 +1055,7 @@ }; gamma0: gamma@14011000 { - compatible = "mediatek,mt8183-disp-gamma", - "mediatek,mt8173-disp-gamma"; + compatible = "mediatek,mt8183-disp-gamma"; reg = <0 0x14011000 0 0x1000>; interrupts = ; power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; From 1cab0a51f62a87227f2e7cbb39b618e30a7cdeb8 Mon Sep 17 00:00:00 2001 From: Jon Hunter Date: Thu, 28 Jan 2021 12:08:50 +0000 Subject: [PATCH 379/584] arm64: tegra: Prepare for supporting the Jetson Xavier NX with eMMC There are two versions of the Jetson Xavier NX system-on-module; one with a micro SD-card slot and one with an eMMC. Currently, only the system-on-module with the micro SD-card slot is supported. Before adding support for the eMMC variant, move the common device-tree parts of the existing Jetson Xavier NX system-on-module board (p3668-0000) and reference carrier board (p3509-0000) into include files that can be used by both Jetson Xavier NX variants. Signed-off-by: Jon Hunter Signed-off-by: Thierry Reding --- .../nvidia/tegra194-p3509-0000+p3668-0000.dts | 351 +----------------- .../boot/dts/nvidia/tegra194-p3509-0000.dtsi | 351 ++++++++++++++++++ .../boot/dts/nvidia/tegra194-p3668-0000.dtsi | 282 +------------- .../arm64/boot/dts/nvidia/tegra194-p3668.dtsi | 284 ++++++++++++++ 4 files changed, 639 insertions(+), 629 deletions(-) create mode 100644 arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi create mode 100644 arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts index f1053e7be45c..1c3874b677c0 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0000.dts @@ -1,357 +1,10 @@ // SPDX-License-Identifier: GPL-2.0 /dts-v1/; -#include -#include - #include "tegra194-p3668-0000.dtsi" +#include "tegra194-p3509-0000.dtsi" / { - model = "NVIDIA Jetson Xavier NX Developer Kit"; + model = "NVIDIA Jetson Xavier NX Developer Kit (SD-card)"; compatible = "nvidia,p3509-0000+p3668-0000", "nvidia,tegra194"; - - bus@0 { - aconnect@2900000 { - status = "okay"; - - dma-controller@2930000 { - status = "okay"; - }; - - interrupt-controller@2a40000 { - status = "okay"; - }; - }; - - ddc: i2c@3190000 { - status = "okay"; - }; - - i2c@3160000 { - eeprom@57 { - compatible = "atmel,24c02"; - reg = <0x57>; - - label = "system"; - vcc-supply = <&vdd_1v8>; - address-width = <8>; - pagesize = <8>; - size = <256>; - read-only; - }; - }; - - hda@3510000 { - nvidia,model = "jetson-xavier-nx-hda"; - status = "okay"; - }; - - padctl@3520000 { - status = "okay"; - - pads { - usb2 { - lanes { - usb2-1 { - status = "okay"; - }; - - usb2-2 { - status = "okay"; - }; - }; - }; - - usb3 { - lanes { - usb3-2 { - status = "okay"; - }; - }; - }; - }; - - ports { - usb2-1 { - mode = "host"; - status = "okay"; - }; - - usb2-2 { - mode = "host"; - vbus-supply = <&vdd_5v0_sys>; - status = "okay"; - }; - - usb3-2 { - nvidia,usb2-companion = <1>; - vbus-supply = <&vdd_5v0_sys>; - status = "okay"; - }; - }; - }; - - usb@3610000 { - status = "okay"; - - phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, - <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-2}>, - <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-2}>; - phy-names = "usb2-1", "usb2-2", "usb3-2"; - }; - - spi@3270000 { - status = "okay"; - - flash@0 { - compatible = "spi-nor"; - reg = <0>; - spi-max-frequency = <102000000>; - spi-tx-bus-width = <4>; - spi-rx-bus-width = <4>; - }; - }; - - pwm@32d0000 { - status = "okay"; - }; - - host1x@13e00000 { - display-hub@15200000 { - status = "okay"; - }; - - dpaux@155c0000 { - status = "okay"; - }; - - dpaux@155d0000 { - status = "okay"; - }; - - /* DP0 */ - sor@15b00000 { - status = "okay"; - - avdd-io-hdmi-dp-supply = <&vdd_1v0>; - vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; - - nvidia,dpaux = <&dpaux0>; - }; - - /* HDMI */ - sor@15b40000 { - status = "okay"; - - avdd-io-hdmi-dp-supply = <&vdd_1v0>; - vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; - hdmi-supply = <&vdd_hdmi>; - - nvidia,ddc-i2c-bus = <&ddc>; - nvidia,hpd-gpio = <&gpio TEGRA194_MAIN_GPIO(M, 1) - GPIO_ACTIVE_LOW>; - }; - }; - }; - - pcie@14160000 { - status = "okay"; - - vddio-pex-ctl-supply = <&vdd_1v8ao>; - - phys = <&p2u_hsio_11>; - phy-names = "p2u-0"; - }; - - pcie@141a0000 { - status = "okay"; - - vddio-pex-ctl-supply = <&vdd_1v8ao>; - - phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, - <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, - <&p2u_nvhs_6>, <&p2u_nvhs_7>; - - phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", - "p2u-5", "p2u-6", "p2u-7"; - }; - - pcie_ep@141a0000 { - status = "disabled"; - - vddio-pex-ctl-supply = <&vdd_1v8ao>; - - reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; - - nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5) - GPIO_ACTIVE_HIGH>; - - phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, - <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, - <&p2u_nvhs_6>, <&p2u_nvhs_7>; - - phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", - "p2u-5", "p2u-6", "p2u-7"; - }; - - fan: fan { - compatible = "pwm-fan"; - pwms = <&pwm6 0 45334>; - - cooling-levels = <0 64 128 255>; - #cooling-cells = <2>; - }; - - gpio-keys { - compatible = "gpio-keys"; - - force-recovery { - label = "Force Recovery"; - gpios = <&gpio TEGRA194_MAIN_GPIO(G, 0) - GPIO_ACTIVE_LOW>; - linux,input-type = ; - linux,code = ; - debounce-interval = <10>; - }; - - power { - label = "Power"; - gpios = <&gpio_aon TEGRA194_AON_GPIO(EE, 4) - GPIO_ACTIVE_LOW>; - linux,input-type = ; - linux,code = ; - debounce-interval = <10>; - wakeup-event-action = ; - wakeup-source; - }; - }; - - vdd_5v0_sys: regulator@100 { - compatible = "regulator-fixed"; - regulator-name = "VDD_5V_SYS"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_3v3_sys: regulator@101 { - compatible = "regulator-fixed"; - regulator-name = "VDD_3V3_SYS"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_3v3_ao: regulator@102 { - compatible = "regulator-fixed"; - regulator-name = "VDD_3V3_AO"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8: regulator@103 { - compatible = "regulator-fixed"; - regulator-name = "VDD_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_hdmi: regulator@104 { - compatible = "regulator-fixed"; - regulator-name = "VDD_5V0_HDMI_CON"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - regulator-boot-on; - }; - - thermal-zones { - cpu { - polling-delay = <0>; - polling-delay-passive = <500>; - status = "okay"; - - trips { - cpu_trip_critical: critical { - temperature = <96500>; - hysteresis = <0>; - type = "critical"; - }; - - cpu_trip_hot: hot { - temperature = <70000>; - hysteresis = <2000>; - type = "hot"; - }; - - cpu_trip_active: active { - temperature = <50000>; - hysteresis = <2000>; - type = "active"; - }; - - cpu_trip_passive: passive { - temperature = <30000>; - hysteresis = <2000>; - type = "passive"; - }; - }; - - cooling-maps { - cpu-critical { - cooling-device = <&fan 3 3>; - trip = <&cpu_trip_critical>; - }; - - cpu-hot { - cooling-device = <&fan 2 2>; - trip = <&cpu_trip_hot>; - }; - - cpu-active { - cooling-device = <&fan 1 1>; - trip = <&cpu_trip_active>; - }; - - cpu-passive { - cooling-device = <&fan 0 0>; - trip = <&cpu_trip_passive>; - }; - }; - }; - - gpu { - polling-delay = <0>; - polling-delay-passive = <500>; - status = "okay"; - - trips { - gpu_alert0: critical { - temperature = <99000>; - hysteresis = <0>; - type = "critical"; - }; - }; - }; - - aux { - polling-delay = <0>; - polling-delay-passive = <500>; - status = "okay"; - - trips { - aux_alert0: critical { - temperature = <90000>; - hysteresis = <0>; - type = "critical"; - }; - }; - }; - }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi new file mode 100644 index 000000000000..d1d77220154f --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi @@ -0,0 +1,351 @@ +// SPDX-License-Identifier: GPL-2.0 + +#include +#include + +/ { + bus@0 { + aconnect@2900000 { + status = "okay"; + + dma-controller@2930000 { + status = "okay"; + }; + + interrupt-controller@2a40000 { + status = "okay"; + }; + }; + + ddc: i2c@3190000 { + status = "okay"; + }; + + i2c@3160000 { + eeprom@57 { + compatible = "atmel,24c02"; + reg = <0x57>; + + label = "system"; + vcc-supply = <&vdd_1v8>; + address-width = <8>; + pagesize = <8>; + size = <256>; + read-only; + }; + }; + + hda@3510000 { + nvidia,model = "jetson-xavier-nx-hda"; + status = "okay"; + }; + + padctl@3520000 { + status = "okay"; + + pads { + usb2 { + lanes { + usb2-1 { + status = "okay"; + }; + + usb2-2 { + status = "okay"; + }; + }; + }; + + usb3 { + lanes { + usb3-2 { + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-1 { + mode = "host"; + status = "okay"; + }; + + usb2-2 { + mode = "host"; + vbus-supply = <&vdd_5v0_sys>; + status = "okay"; + }; + + usb3-2 { + nvidia,usb2-companion = <1>; + vbus-supply = <&vdd_5v0_sys>; + status = "okay"; + }; + }; + }; + + usb@3610000 { + status = "okay"; + + phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-1}>, + <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-2}>, + <&{/bus@0/padctl@3520000/pads/usb3/lanes/usb3-2}>; + phy-names = "usb2-1", "usb2-2", "usb3-2"; + }; + + spi@3270000 { + status = "okay"; + + flash@0 { + compatible = "spi-nor"; + reg = <0>; + spi-max-frequency = <102000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; + }; + + pwm@32d0000 { + status = "okay"; + }; + + host1x@13e00000 { + display-hub@15200000 { + status = "okay"; + }; + + dpaux@155c0000 { + status = "okay"; + }; + + dpaux@155d0000 { + status = "okay"; + }; + + /* DP0 */ + sor@15b00000 { + status = "okay"; + + avdd-io-hdmi-dp-supply = <&vdd_1v0>; + vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; + + nvidia,dpaux = <&dpaux0>; + }; + + /* HDMI */ + sor@15b40000 { + status = "okay"; + + avdd-io-hdmi-dp-supply = <&vdd_1v0>; + vdd-hdmi-dp-pll-supply = <&vdd_1v8hs>; + hdmi-supply = <&vdd_hdmi>; + + nvidia,ddc-i2c-bus = <&ddc>; + nvidia,hpd-gpio = <&gpio TEGRA194_MAIN_GPIO(M, 1) + GPIO_ACTIVE_LOW>; + }; + }; + }; + + pcie@14160000 { + status = "okay"; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + phys = <&p2u_hsio_11>; + phy-names = "p2u-0"; + }; + + pcie@141a0000 { + status = "okay"; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, + <&p2u_nvhs_6>, <&p2u_nvhs_7>; + + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", + "p2u-5", "p2u-6", "p2u-7"; + }; + + pcie_ep@141a0000 { + status = "disabled"; + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + reset-gpios = <&gpio TEGRA194_MAIN_GPIO(GG, 1) GPIO_ACTIVE_LOW>; + + nvidia,refclk-select-gpios = <&gpio_aon TEGRA194_AON_GPIO(AA, 5) + GPIO_ACTIVE_HIGH>; + + phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>, + <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>, + <&p2u_nvhs_6>, <&p2u_nvhs_7>; + + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4", + "p2u-5", "p2u-6", "p2u-7"; + }; + + fan: fan { + compatible = "pwm-fan"; + pwms = <&pwm6 0 45334>; + + cooling-levels = <0 64 128 255>; + #cooling-cells = <2>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + force-recovery { + label = "Force Recovery"; + gpios = <&gpio TEGRA194_MAIN_GPIO(G, 0) + GPIO_ACTIVE_LOW>; + linux,input-type = ; + linux,code = ; + debounce-interval = <10>; + }; + + power { + label = "Power"; + gpios = <&gpio_aon TEGRA194_AON_GPIO(EE, 4) + GPIO_ACTIVE_LOW>; + linux,input-type = ; + linux,code = ; + debounce-interval = <10>; + wakeup-event-action = ; + wakeup-source; + }; + }; + + vdd_5v0_sys: regulator@100 { + compatible = "regulator-fixed"; + regulator-name = "VDD_5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3_sys: regulator@101 { + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3_SYS"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_3v3_ao: regulator@102 { + compatible = "regulator-fixed"; + regulator-name = "VDD_3V3_AO"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8: regulator@103 { + compatible = "regulator-fixed"; + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_hdmi: regulator@104 { + compatible = "regulator-fixed"; + regulator-name = "VDD_5V0_HDMI_CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + thermal-zones { + cpu { + polling-delay = <0>; + polling-delay-passive = <500>; + status = "okay"; + + trips { + cpu_trip_critical: critical { + temperature = <96500>; + hysteresis = <0>; + type = "critical"; + }; + + cpu_trip_hot: hot { + temperature = <70000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpu_trip_active: active { + temperature = <50000>; + hysteresis = <2000>; + type = "active"; + }; + + cpu_trip_passive: passive { + temperature = <30000>; + hysteresis = <2000>; + type = "passive"; + }; + }; + + cooling-maps { + cpu-critical { + cooling-device = <&fan 3 3>; + trip = <&cpu_trip_critical>; + }; + + cpu-hot { + cooling-device = <&fan 2 2>; + trip = <&cpu_trip_hot>; + }; + + cpu-active { + cooling-device = <&fan 1 1>; + trip = <&cpu_trip_active>; + }; + + cpu-passive { + cooling-device = <&fan 0 0>; + trip = <&cpu_trip_passive>; + }; + }; + }; + + gpu { + polling-delay = <0>; + polling-delay-passive = <500>; + status = "okay"; + + trips { + gpu_alert0: critical { + temperature = <99000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + + aux { + polling-delay = <0>; + polling-delay-passive = <500>; + status = "okay"; + + trips { + aux_alert0: critical { + temperature = <90000>; + hysteresis = <0>; + type = "critical"; + }; + }; + }; + }; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi index 0dc8304a2edd..7da3d48cb410 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi @@ -1,79 +1,11 @@ // SPDX-License-Identifier: GPL-2.0 -#include "tegra194.dtsi" - -#include +#include "tegra194-p3668.dtsi" / { - model = "NVIDIA Jetson Xavier NX"; + model = "NVIDIA Jetson Xavier NX (SD-card)"; compatible = "nvidia,p3668-0000", "nvidia,tegra194"; - aliases { - ethernet0 = "/bus@0/ethernet@2490000"; - i2c0 = "/bpmp/i2c"; - i2c1 = "/bus@0/i2c@3160000"; - i2c2 = "/bus@0/i2c@c240000"; - i2c3 = "/bus@0/i2c@3180000"; - i2c4 = "/bus@0/i2c@3190000"; - i2c5 = "/bus@0/i2c@31c0000"; - i2c6 = "/bus@0/i2c@c250000"; - i2c7 = "/bus@0/i2c@31e0000"; - mmc0 = "/bus@0/mmc@3460000"; - rtc0 = "/bpmp/i2c/pmic@3c"; - rtc1 = "/bus@0/rtc@c2a0000"; - serial0 = &tcu; - }; - - chosen { - bootargs = "console=ttyS0,115200n8"; - stdout-path = "serial0:115200n8"; - }; - bus@0 { - ethernet@2490000 { - status = "okay"; - - phy-reset-gpios = <&gpio TEGRA194_MAIN_GPIO(R, 1) GPIO_ACTIVE_LOW>; - phy-handle = <&phy>; - phy-mode = "rgmii-id"; - - mdio { - #address-cells = <1>; - #size-cells = <0>; - - phy: phy@0 { - compatible = "ethernet-phy-ieee802.3-c22"; - reg = <0x0>; - interrupt-parent = <&gpio>; - interrupts = ; - #phy-cells = <0>; - }; - }; - }; - - memory-controller@2c00000 { - status = "okay"; - }; - - serial@3100000 { - status = "okay"; - }; - - i2c@3160000 { - status = "okay"; - - eeprom@50 { - compatible = "atmel,24c02"; - reg = <0x50>; - - label = "module"; - vcc-supply = <&vdd_1v8ls>; - address-width = <8>; - pagesize = <8>; - size = <256>; - read-only; - }; - }; - /* SDMMC1 (SD/MMC) */ mmc@3400000 { status = "okay"; @@ -82,216 +14,6 @@ disable-wp; vmmc-supply = <&vdd_3v3_sd>; }; - - padctl@3520000 { - avdd-usb-supply = <&vdd_usb_3v3>; - vclamp-usb-supply = <&vdd_1v8ao>; - - ports { - usb2-1 { - vbus-supply = <&vdd_5v0_sys>; - }; - - usb2-3 { - vbus-supply = <&vdd_5v0_sys>; - }; - - usb3-0 { - vbus-supply = <&vdd_5v0_sys>; - }; - - usb3-3 { - vbus-supply = <&vdd_5v0_sys>; - }; - }; - }; - - rtc@c2a0000 { - status = "okay"; - }; - - pmc@c360000 { - nvidia,invert-interrupt; - }; - }; - - bpmp { - i2c { - status = "okay"; - - pmic: pmic@3c { - compatible = "maxim,max20024"; - reg = <0x3c>; - - interrupt-parent = <&pmc>; - interrupts = <24 IRQ_TYPE_LEVEL_LOW>; - #interrupt-cells = <2>; - interrupt-controller; - - #gpio-cells = <2>; - gpio-controller; - - pinctrl-names = "default"; - pinctrl-0 = <&max20024_default>; - - max20024_default: pinmux { - gpio0 { - pins = "gpio0"; - function = "gpio"; - }; - - gpio1 { - pins = "gpio1"; - function = "fps-out"; - maxim,active-fps-source = ; - }; - - gpio2 { - pins = "gpio2"; - function = "fps-out"; - maxim,active-fps-source = ; - }; - - gpio3 { - pins = "gpio3"; - function = "fps-out"; - maxim,active-fps-source = ; - }; - - gpio4 { - pins = "gpio4"; - function = "32k-out1"; - drive-push-pull = <1>; - }; - - gpio6 { - pins = "gpio6"; - function = "gpio"; - drive-push-pull = <1>; - }; - - gpio7 { - pins = "gpio7"; - function = "gpio"; - drive-push-pull = <0>; - }; - }; - - fps { - fps0 { - maxim,fps-event-source = ; - maxim,shutdown-fps-time-period-us = <640>; - }; - - fps1 { - maxim,fps-event-source = ; - maxim,shutdown-fps-time-period-us = <640>; - maxim,device-state-on-disabled-event = ; - }; - - fps2 { - maxim,fps-event-source = ; - maxim,shutdown-fps-time-period-us = <640>; - }; - }; - - regulators { - in-sd0-supply = <&vdd_5v0_sys>; - in-sd1-supply = <&vdd_5v0_sys>; - in-sd2-supply = <&vdd_5v0_sys>; - in-sd3-supply = <&vdd_5v0_sys>; - in-sd4-supply = <&vdd_5v0_sys>; - - in-ldo0-1-supply = <&vdd_5v0_sys>; - in-ldo2-supply = <&vdd_5v0_sys>; - in-ldo3-5-supply = <&vdd_5v0_sys>; - in-ldo4-6-supply = <&vdd_5v0_sys>; - in-ldo7-8-supply = <&vdd_1v8ls>; - - vdd_1v0: sd0 { - regulator-name = "VDDIO_SYS_1V0"; - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1000000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8hs: sd1 { - regulator-name = "VDDIO_SYS_1V8HS"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8ls: sd2 { - regulator-name = "VDDIO_SYS_1V8LS"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - vdd_1v8ao: sd3 { - regulator-name = "VDDIO_AO_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - regulator-always-on; - regulator-boot-on; - }; - - sd4 { - regulator-name = "VDD_DDR_1V1"; - regulator-min-microvolt = <1100000>; - regulator-max-microvolt = <1100000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo0 { - regulator-name = "VDD_RTC"; - regulator-min-microvolt = <800000>; - regulator-max-microvolt = <800000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo2 { - regulator-name = "VDDIO_AO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo3 { - regulator-name = "VDD_EMMC_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - vdd_usb_3v3: ldo5 { - regulator-name = "VDD_USB_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - regulator-boot-on; - }; - - ldo6 { - regulator-name = "VDD_SDIO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - }; - - ldo7 { - regulator-name = "AVDD_CSI_1V2"; - regulator-min-microvolt = <1200000>; - regulator-max-microvolt = <1200000>; - }; - }; - }; - }; }; vdd_3v3_sd: regulator@0 { diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi new file mode 100644 index 000000000000..a26b8a37f884 --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi @@ -0,0 +1,284 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "tegra194.dtsi" + +#include + +/ { + aliases { + ethernet0 = "/bus@0/ethernet@2490000"; + i2c0 = "/bpmp/i2c"; + i2c1 = "/bus@0/i2c@3160000"; + i2c2 = "/bus@0/i2c@c240000"; + i2c3 = "/bus@0/i2c@3180000"; + i2c4 = "/bus@0/i2c@3190000"; + i2c5 = "/bus@0/i2c@31c0000"; + i2c6 = "/bus@0/i2c@c250000"; + i2c7 = "/bus@0/i2c@31e0000"; + mmc0 = "/bus@0/mmc@3460000"; + rtc0 = "/bpmp/i2c/pmic@3c"; + rtc1 = "/bus@0/rtc@c2a0000"; + serial0 = &tcu; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "serial0:115200n8"; + }; + + bus@0 { + ethernet@2490000 { + status = "okay"; + + phy-reset-gpios = <&gpio TEGRA194_MAIN_GPIO(R, 1) GPIO_ACTIVE_LOW>; + phy-handle = <&phy>; + phy-mode = "rgmii-id"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy: phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + interrupt-parent = <&gpio>; + interrupts = ; + #phy-cells = <0>; + }; + }; + }; + + memory-controller@2c00000 { + status = "okay"; + }; + + serial@3100000 { + status = "okay"; + }; + + i2c@3160000 { + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + + label = "module"; + vcc-supply = <&vdd_1v8ls>; + address-width = <8>; + pagesize = <8>; + size = <256>; + read-only; + }; + }; + + padctl@3520000 { + avdd-usb-supply = <&vdd_usb_3v3>; + vclamp-usb-supply = <&vdd_1v8ao>; + + ports { + usb2-1 { + vbus-supply = <&vdd_5v0_sys>; + }; + + usb2-3 { + vbus-supply = <&vdd_5v0_sys>; + }; + + usb3-0 { + vbus-supply = <&vdd_5v0_sys>; + }; + + usb3-3 { + vbus-supply = <&vdd_5v0_sys>; + }; + }; + }; + + rtc@c2a0000 { + status = "okay"; + }; + + pmc@c360000 { + nvidia,invert-interrupt; + }; + }; + + bpmp { + i2c { + status = "okay"; + + pmic: pmic@3c { + compatible = "maxim,max20024"; + reg = <0x3c>; + + interrupt-parent = <&pmc>; + interrupts = <24 IRQ_TYPE_LEVEL_LOW>; + #interrupt-cells = <2>; + interrupt-controller; + + #gpio-cells = <2>; + gpio-controller; + + pinctrl-names = "default"; + pinctrl-0 = <&max20024_default>; + + max20024_default: pinmux { + gpio0 { + pins = "gpio0"; + function = "gpio"; + }; + + gpio1 { + pins = "gpio1"; + function = "fps-out"; + maxim,active-fps-source = ; + }; + + gpio2 { + pins = "gpio2"; + function = "fps-out"; + maxim,active-fps-source = ; + }; + + gpio3 { + pins = "gpio3"; + function = "fps-out"; + maxim,active-fps-source = ; + }; + + gpio4 { + pins = "gpio4"; + function = "32k-out1"; + drive-push-pull = <1>; + }; + + gpio6 { + pins = "gpio6"; + function = "gpio"; + drive-push-pull = <1>; + }; + + gpio7 { + pins = "gpio7"; + function = "gpio"; + drive-push-pull = <0>; + }; + }; + + fps { + fps0 { + maxim,fps-event-source = ; + maxim,shutdown-fps-time-period-us = <640>; + }; + + fps1 { + maxim,fps-event-source = ; + maxim,shutdown-fps-time-period-us = <640>; + maxim,device-state-on-disabled-event = ; + }; + + fps2 { + maxim,fps-event-source = ; + maxim,shutdown-fps-time-period-us = <640>; + }; + }; + + regulators { + in-sd0-supply = <&vdd_5v0_sys>; + in-sd1-supply = <&vdd_5v0_sys>; + in-sd2-supply = <&vdd_5v0_sys>; + in-sd3-supply = <&vdd_5v0_sys>; + in-sd4-supply = <&vdd_5v0_sys>; + + in-ldo0-1-supply = <&vdd_5v0_sys>; + in-ldo2-supply = <&vdd_5v0_sys>; + in-ldo3-5-supply = <&vdd_5v0_sys>; + in-ldo4-6-supply = <&vdd_5v0_sys>; + in-ldo7-8-supply = <&vdd_1v8ls>; + + vdd_1v0: sd0 { + regulator-name = "VDDIO_SYS_1V0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8hs: sd1 { + regulator-name = "VDDIO_SYS_1V8HS"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8ls: sd2 { + regulator-name = "VDDIO_SYS_1V8LS"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + vdd_1v8ao: sd3 { + regulator-name = "VDDIO_AO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + sd4 { + regulator-name = "VDD_DDR_1V1"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "VDD_RTC"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo2 { + regulator-name = "VDDIO_AO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo3 { + regulator-name = "VDD_EMMC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + vdd_usb_3v3: ldo5 { + regulator-name = "VDD_USB_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6 { + regulator-name = "VDD_SDIO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo7 { + regulator-name = "AVDD_CSI_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + }; + }; + }; + }; +}; From f16013020440bf075e94bd2b9147c1e4b5abcfc6 Mon Sep 17 00:00:00 2001 From: Jon Hunter Date: Thu, 28 Jan 2021 12:08:51 +0000 Subject: [PATCH 380/584] arm64: tegra: Add support for Jetson Xavier NX with eMMC Add support for the variant of the Jetson Xavier NX Developer Kit that has a system-on-module which includes an eMMC. Signed-off-by: Jon Hunter Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/Makefile | 1 + .../nvidia/tegra194-p3509-0000+p3668-0001.dts | 10 ++++++++++ .../boot/dts/nvidia/tegra194-p3668-0001.dtsi | 19 +++++++++++++++++++ .../arm64/boot/dts/nvidia/tegra194-p3668.dtsi | 2 +- 4 files changed, 31 insertions(+), 1 deletion(-) create mode 100644 arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts create mode 100644 arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi diff --git a/arch/arm64/boot/dts/nvidia/Makefile b/arch/arm64/boot/dts/nvidia/Makefile index 9296d12d11e9..e13fb1070472 100644 --- a/arch/arm64/boot/dts/nvidia/Makefile +++ b/arch/arm64/boot/dts/nvidia/Makefile @@ -9,4 +9,5 @@ dtb-$(CONFIG_ARCH_TEGRA_210_SOC) += tegra210-p2894-0050-a08.dtb dtb-$(CONFIG_ARCH_TEGRA_186_SOC) += tegra186-p2771-0000.dtb dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p2972-0000.dtb dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p3509-0000+p3668-0000.dtb +dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p3509-0000+p3668-0001.dtb dtb-$(CONFIG_ARCH_TEGRA_234_SOC) += tegra234-sim-vdk.dtb diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts new file mode 100644 index 000000000000..238fd98e8e45 --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000+p3668-0001.dts @@ -0,0 +1,10 @@ +// SPDX-License-Identifier: GPL-2.0 +/dts-v1/; + +#include "tegra194-p3668-0001.dtsi" +#include "tegra194-p3509-0000.dtsi" + +/ { + model = "NVIDIA Jetson Xavier NX Developer Kit (eMMC)"; + compatible = "nvidia,p3509-0000+p3668-0001", "nvidia,tegra194"; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi new file mode 100644 index 000000000000..b7808648cfe4 --- /dev/null +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0001.dtsi @@ -0,0 +1,19 @@ +// SPDX-License-Identifier: GPL-2.0 +#include "tegra194-p3668.dtsi" + +/ { + model = "NVIDIA Jetson Xavier NX (eMMC)"; + compatible = "nvidia,p3668-0001", "nvidia,tegra194"; + + bus@0 { + /* SDMMC4 (eMMC) */ + mmc@3460000 { + status = "okay"; + bus-width = <8>; + non-removable; + + vqmmc-supply = <&vdd_1v8ls>; + vmmc-supply = <&vdd_emmc_3v3>; + }; + }; +}; diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi index a26b8a37f884..4f12721c332b 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi @@ -252,7 +252,7 @@ regulator-boot-on; }; - ldo3 { + vdd_emmc_3v3: ldo3 { regulator-name = "VDD_EMMC_3V3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; From 2f99fb6e46b0e982bb6ab18b24a08fa318f740ea Mon Sep 17 00:00:00 2001 From: Enric Balletbo i Serra Date: Wed, 13 Jan 2021 22:57:23 +0100 Subject: [PATCH 381/584] arm64: dts: mt8183: Add missing power-domain for pwm0 node The MT8183 display PWM device will not work until the associated power-domain is enabled. Add the power-domain reference to the node allows the display PWM driver to operate and the backlight turn on. Fixes: f15722c0fef0 ("arm64: dts: mt8183: Add pwm and backlight node") Signed-off-by: Enric Balletbo i Serra Reviewed-by: Hsin-Yi Wang Link: https://lore.kernel.org/r/20210113215723.71966-1-enric.balletbo@collabora.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index 9c0073cfad45..64fbba76597c 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -661,6 +661,7 @@ compatible = "mediatek,mt8183-disp-pwm"; reg = <0 0x1100e000 0 0x1000>; interrupts = ; + power-domains = <&spm MT8183_POWER_DOMAIN_DISP>; #pwm-cells = <2>; clocks = <&topckgen CLK_TOP_MUX_DISP_PWM>, <&infracfg CLK_INFRA_DISP_PWM>; From c0b70f05c87f3b09b391027c6f056d0facf331ef Mon Sep 17 00:00:00 2001 From: Peng Fan Date: Fri, 15 Jan 2021 11:26:57 +0800 Subject: [PATCH 382/584] arm64: dts: imx8mq: use_dt_domains for pci node We are using Jailhouse Hypervsior which has virtual pci node that use dt domains. so also use dt domains for pci node, this will avoid conflict with Jailhouse Hypervisor to trigger the following error: pr_err("Inconsistent \"linux,pci-domain\" property in DT\n"); Reviewed-by: Richard Zhu Signed-off-by: Peng Fan Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 963c97b4ba84..17c449e12c2e 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -1377,6 +1377,7 @@ <0 0 0 3 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <0 0 0 4 &gic GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; fsl,max-link-speed = <2>; + linux,pci-domain = <0>; power-domains = <&pgc_pcie>; resets = <&src IMX8MQ_RESET_PCIEPHY>, <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>, @@ -1406,6 +1407,7 @@ <0 0 0 3 &gic GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>, <0 0 0 4 &gic GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; fsl,max-link-speed = <2>; + linux,pci-domain = <1>; power-domains = <&pgc_pcie>; resets = <&src IMX8MQ_RESET_PCIEPHY2>, <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>, From 22171213e503edce38f249cff82b9ad3775b9026 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 15 Jan 2021 23:36:39 +0000 Subject: [PATCH 383/584] arm64: dts: lx2160a-cex7: increase at8035 PHY gigabit Tw parameter Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit links from sporadically dropping. Testing on this platform shows that a value of 24 results in a stable link, whereas 23 or below has the occasional drop. Tested with a Netgear GS116 unmanaged switch link partner with Cat 5e cabling. Signed-off-by: Russell King Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi index 49fcf025494f..459dccad8326 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-cex7.dtsi @@ -40,6 +40,7 @@ rgmii_phy1: ethernet-phy@1 { reg = <1>; + qca,smarteee-tw-us-1g = <24>; }; }; From b73d538a01305446e843a6be45853cce1438acdd Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 15 Jan 2021 23:36:44 +0000 Subject: [PATCH 384/584] ARM: dts: imx6-sr-som: increase at8035 PHY gigabit Tw parameter Increase the SmartEEE Tw parameter for Atheros PHYs to stop gigabit links from sporadically dropping. Jon Nettleton found that a value of 23 was the minimum to give a stable link, but testing with the Com Express 7 module shows 24 is the minimum - so 23 may still be on the margins. Use 24 instead for consistency across SolidRun platforms. Signed-off-by: Russell King Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-sr-som.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi index 7e4e5fd0143a..0ad8ccde0cf8 100644 --- a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi @@ -69,11 +69,13 @@ ethernet-phy@0 { reg = <0>; qca,clk-out-frequency = <125000000>; + qca,smarteee-tw-us-1g = <24>; }; ethernet-phy@4 { reg = <4>; qca,clk-out-frequency = <125000000>; + qca,smarteee-tw-us-1g = <24>; }; }; }; From 74477936a828a7c91a61ba7e625b7ce2299c8c98 Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 28 Jan 2021 12:01:36 +0100 Subject: [PATCH 385/584] arm64: dts: renesas: beacon: Fix EEPROM compatible value "make dtbs_check" fails with: arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dt.yaml: eeprom@50: compatible: 'oneOf' conditional failed, one must be fixed: 'microchip,at24c64' does not match '^(atmel|catalyst|microchip|nxp|ramtron|renesas|rohm|st),(24(c|cs|lc|mac)[0-9]+|spd)$' Fix this by dropping the bogus "at" prefix. Fixes: a1d8a344f1ca0709 ("arm64: dts: renesas: Introduce r8a774a1-beacon-rzg2m-kit") Signed-off-by: Geert Uytterhoeven Link: https://lore.kernel.org/r/20210128110136.2293490-1-geert+renesas@glider.be --- arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi index c9bf5234dbd0..8d3a4d6ee885 100644 --- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi +++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi @@ -144,7 +144,7 @@ }; eeprom@50 { - compatible = "microchip,at24c64", "atmel,24c64"; + compatible = "microchip,24c64", "atmel,24c64"; pagesize = <32>; read-only; /* Manufacturing EEPROM programmed at factory */ reg = <0x50>; From 894fe3398a2175a471fae33fdbada36a66ddce12 Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Mon, 18 Jan 2021 11:54:24 +0100 Subject: [PATCH 386/584] dt-bindings: arm: fsl: Add the librem 5 Evergreen revision Add an entry for the Librem 5 phone, Evergreen revision which is supported by "r4". Schematics and more information can be found at https://developer.puri.sm/Librem5/Hardware_Reference/Evergreen.html Signed-off-by: Martin Kepplinger Reviewed-by: Krzysztof Kozlowski Acked-by: Rob Herring Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 65038b16302e..47220e2f522c 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -742,6 +742,7 @@ properties: - enum: - purism,librem5r2 # Purism Librem5 phone "Chestnut" - purism,librem5r3 # Purism Librem5 phone "Dogwood" + - purism,librem5r4 # Purism Librem5 phone "Evergreen" - const: purism,librem5 - const: fsl,imx8mq From 3bb48247ea16e03dbe5797ecc0cecd8399c2e927 Mon Sep 17 00:00:00 2001 From: Jagan Teki Date: Wed, 23 Dec 2020 16:37:57 +0530 Subject: [PATCH 387/584] ARM: dts: stm32: Add STM32MP1 I2C6 SDA/SCL pinmux Add SDA/SCL pinmux lines for I2C6 on STM32MP1. This support adds both in default and sleep states. Signed-off-by: Jagan Teki Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 17 +++++++++++++++++ 1 file changed, 17 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi index 53326ed652f8..7b4249ed1983 100644 --- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi +++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi @@ -2041,6 +2041,23 @@ }; }; + i2c6_pins_a: i2c6-0 { + pins { + pinmux = , /* I2C6_SCL */ + ; /* I2C6_SDA */ + bias-disable; + drive-open-drain; + slew-rate = <0>; + }; + }; + + i2c6_sleep_pins_a: i2c6-sleep-0 { + pins { + pinmux = , /* I2C6_SCL */ + ; /* I2C6_SDA */ + }; + }; + spi1_pins_a: spi1-0 { pins1 { pinmux = , /* SPI1_SCK */ From c9669b4692ce5d0d1eb98fa1a187233492e19a01 Mon Sep 17 00:00:00 2001 From: Amelie Delaunay Date: Thu, 14 Jan 2021 14:15:22 +0100 Subject: [PATCH 388/584] ARM: dts: stm32: add usbphyc vdda1v1 and vdda1v8 supplies on stm32mp151 vdda1v1 and vdda1v8 supplies are required by USB PLL. Add them in usbphyc node. Cc: Manivannan Sadhasivam Signed-off-by: Amelie Delaunay Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp151.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi index 0d4db78ae255..7c7895338498 100644 --- a/arch/arm/boot/dts/stm32mp151.dtsi +++ b/arch/arm/boot/dts/stm32mp151.dtsi @@ -1486,6 +1486,8 @@ reg = <0x5a006000 0x1000>; clocks = <&rcc USBPHY_K>; resets = <&rcc USBPHY_R>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; status = "disabled"; usbphyc_port0: usb-phy@0 { From c96f8d3ca78c51bafe88969f21342fbd1a8021f4 Mon Sep 17 00:00:00 2001 From: Amelie Delaunay Date: Thu, 14 Jan 2021 14:15:23 +0100 Subject: [PATCH 389/584] ARM: dts: stm32: remove usbphyc ports vdda1v1 & vdda1v8 on stm32mp15 boards vdda1v1 and vdda1v8 supplies are required by USB PLL, not by the PHYs. Remove them from usbphyc child phy nodes now that they are managed in usbphyc parent node at SoC level. Cc: Manivannan Sadhasivam Signed-off-by: Amelie Delaunay Tested-by: Marek Vasut Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp157a-stinger96.dtsi | 4 ---- arch/arm/boot/dts/stm32mp157c-ed1.dts | 4 ---- arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 2 -- arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 4 ---- arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi | 4 ---- arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi | 4 ---- arch/arm/boot/dts/stm32mp15xx-dkx.dtsi | 4 ---- 7 files changed, 26 deletions(-) diff --git a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi index 58275bcf9e26..113c48b2ef93 100644 --- a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi +++ b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi @@ -331,12 +331,8 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &usbphyc_port1 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts index 81a7d5849db4..95b08876b2b3 100644 --- a/arch/arm/boot/dts/stm32mp157c-ed1.dts +++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts @@ -393,12 +393,8 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &usbphyc_port1 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi index 5088dd3a301b..fad23d6f69b8 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi @@ -158,6 +158,4 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi index 8456f172d4b1..5523f4138fd6 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi @@ -300,12 +300,8 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &usbphyc_port1 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi index 757707766fa0..cd3a1798ca68 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi @@ -140,12 +140,8 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &usbphyc_port1 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi index ec02cee1dd9b..b09e87fe901a 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi @@ -391,12 +391,8 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &usbphyc_port1 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; diff --git a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi index 89c0e1ddc387..59f18846cf5d 100644 --- a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi +++ b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi @@ -694,14 +694,10 @@ &usbphyc_port0 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &usbphyc_port1 { phy-supply = <&vdd_usb>; - vdda1v1-supply = <®11>; - vdda1v8-supply = <®18>; }; &vrefbuf { From 36be90f5362a3174071a543fa73eb0f6d66bdf52 Mon Sep 17 00:00:00 2001 From: Amelie Delaunay Date: Thu, 14 Jan 2021 14:15:24 +0100 Subject: [PATCH 390/584] ARM: dts: stm32: add #clock-cells property to usbphyc node on stm32mp151 usbphyc is a 48Mhz clock provider: the clock can be used as clock source for USB OTG. Add #clock-cells property to usbphyc node to reflect this capability. Signed-off-by: Amelie Delaunay Signed-off-by: Alexandre Torgue --- arch/arm/boot/dts/stm32mp151.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi index 7c7895338498..4b8031782555 100644 --- a/arch/arm/boot/dts/stm32mp151.dtsi +++ b/arch/arm/boot/dts/stm32mp151.dtsi @@ -1482,6 +1482,7 @@ usbphyc: usbphyc@5a006000 { #address-cells = <1>; #size-cells = <0>; + #clock-cells = <0>; compatible = "st,stm32mp1-usbphyc"; reg = <0x5a006000 0x1000>; clocks = <&rcc USBPHY_K>; From f3dbb291814a72b17875d7e261a3bc53f8299692 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Mon, 18 Jan 2021 11:54:18 +0100 Subject: [PATCH 391/584] arm64: dts: imx8mq-librem5: Mark charger IRQ as High-Z MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This is consistent with other IRQs and makes keeps currents low. Signed-off-by: Guido Günther Signed-off-by: Martin Kepplinger Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index f85d30a0c2cb..9928e941ee21 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -276,7 +276,7 @@ pinctrl_charger_in: chargeringrp { fsl,pins = < /* CHRG_INT */ - MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x00 + MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x80 /* CHG_STATUS_B */ MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0 0x80 >; From 99e71c029213d3cfcc4f39a534c73d1828ffb341 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Mon, 18 Jan 2021 11:54:19 +0100 Subject: [PATCH 392/584] arm64: dts: imx8mq-librem5: Don't mark buck3 as always on MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit With the pmic driver fixed we can now shut off the regulator in the gpc. Signed-off-by: Guido Günther Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 9928e941ee21..95d710831f28 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -679,7 +679,6 @@ regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; rohm,dvs-run-voltage = <900000>; - regulator-always-on; }; buck4_reg: BUCK4 { From d5edcf2cbf5e28008e8f7eed63305bbfd14637cf Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Mon, 18 Jan 2021 11:54:20 +0100 Subject: [PATCH 393/584] arm64: dts: imx8mq-librem5: Add usb-c chip as supplier for the charger MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The tps65982 feeds the bq25895 charge controller on the Librem 5. Signed-off-by: Guido Günther Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index 95d710831f28..d7d807cd72b3 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -928,6 +928,7 @@ ti,use-vinmin-threshold = <1>; /* enable VINDPM */ ti,vinmin-threshold = <3900000>; /* uV */ monitored-battery = <&bat>; + power-supplies = <&typec_pd>; }; }; From 7127e3b5d93d8a1ee01eab04011ab6d1fff79ee1 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Guido=20G=C3=BCnther?= Date: Mon, 18 Jan 2021 11:54:21 +0100 Subject: [PATCH 394/584] arm64: dts: imx8mq-librem5: Add LCD_1V8 regulator MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It's a supply for to touch and LCD. Signed-off-by: Guido Günther Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index d7d807cd72b3..f77b51d3c132 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -82,6 +82,20 @@ enable-active-high; }; + reg_lcd_1v8: regulator-lcd-1v8 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dsien>; + regulator-name = "LCD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <®_vdd_1v8>; + gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; + enable-active-high; + /* Otherwise i2c3 is not functional */ + regulator-always-on; + }; + reg_lcd_3v4: regulator-lcd-3v4 { compatible = "regulator-fixed"; regulator-name = "LCD_3V4"; @@ -892,6 +906,7 @@ interrupts = <27 IRQ_TYPE_EDGE_FALLING>; touchscreen-size-x = <720>; touchscreen-size-y = <1440>; + vcc-supply = <®_lcd_1v8>; }; }; From 584ea5b1499ee6e07cf82d2d12c1862c38b3d089 Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Mon, 18 Jan 2021 11:54:22 +0100 Subject: [PATCH 395/584] arm64: dts: imx8mq-librem5: enable the LCD panel This enables the Librem5's ft8006p based LCD panel driven by the imx8mq's Northwest Logic DSI IP core and mxsfb display controller. Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- .../boot/dts/freescale/imx8mq-librem5.dtsi | 53 ++++++++++++++++++- 1 file changed, 51 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index f77b51d3c132..bf86402cda30 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -310,6 +310,17 @@ >; }; + pinctrl_dsirst: dsirstgrp { + fsl,pins = < + /* DSI_RST */ + MX8MQ_IOMUXC_ENET_RD3_GPIO1_IO29 0x83 + /* DSI_TE */ + MX8MQ_IOMUXC_ENET_RD2_GPIO1_IO28 0x83 + /* TP_RST */ + MX8MQ_IOMUXC_ENET_RX_CTL_GPIO1_IO24 0x83 + >; + }; + pinctrl_ecspi1: ecspigrp { fsl,pins = < MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x83 @@ -817,12 +828,12 @@ compatible = "tps65132"; reg = <0x3e>; - outp { + reg_lcd_avdd: outp { regulator-name = "LCD_AVDD"; vin-supply = <®_lcd_3v4>; }; - outn { + reg_lcd_avee: outn { regulator-name = "LCD_AVEE"; vin-supply = <®_lcd_3v4>; }; @@ -947,6 +958,44 @@ }; }; +&lcdif { + status = "okay"; +}; + +&mipi_dsi { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + lcd_panel: panel@0 { + compatible = "mantix,mlaf057we51-x"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_dsirst>; + avdd-supply = <®_lcd_avdd>; + avee-supply = <®_lcd_avee>; + vddi-supply = <®_lcd_1v8>; + backlight = <&backlight_dsi>; + reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + + port { + panel_in: endpoint { + remote-endpoint = <&mipi_dsi_out>; + }; + }; + }; + + ports { + port@1 { + reg = <1>; + + mipi_dsi_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + &pgc_gpu { power-supply = <&buck3_reg>; }; From a8bb83c8c7a17e83e04801d0678e93654f9bfaee Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Mon, 18 Jan 2021 11:54:23 +0100 Subject: [PATCH 396/584] arm64: dts: imx8mq-librem5: set regulators boot-on Expect all those regulators to be turned on initially. Signed-off-by: Martin Kepplinger Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi index bf86402cda30..06a4799b6aeb 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi @@ -682,6 +682,7 @@ regulator-name = "buck1"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; + regulator-boot-on; regulator-ramp-delay = <1250>; rohm,dvs-run-voltage = <900000>; rohm,dvs-idle-voltage = <850000>; @@ -693,6 +694,7 @@ regulator-name = "buck2"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; + regulator-boot-on; regulator-ramp-delay = <1250>; rohm,dvs-run-voltage = <1000000>; rohm,dvs-idle-voltage = <900000>; @@ -703,6 +705,7 @@ regulator-name = "buck3"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1300000>; + regulator-boot-on; rohm,dvs-run-voltage = <900000>; }; @@ -717,6 +720,7 @@ regulator-name = "buck5"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1350000>; + regulator-boot-on; regulator-always-on; }; @@ -724,6 +728,7 @@ regulator-name = "buck6"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3300000>; + regulator-boot-on; regulator-always-on; }; @@ -731,6 +736,7 @@ regulator-name = "buck7"; regulator-min-microvolt = <1605000>; regulator-max-microvolt = <1995000>; + regulator-boot-on; regulator-always-on; }; @@ -738,6 +744,7 @@ regulator-name = "buck8"; regulator-min-microvolt = <800000>; regulator-max-microvolt = <1400000>; + regulator-boot-on; regulator-always-on; }; @@ -745,6 +752,7 @@ regulator-name = "ldo1"; regulator-min-microvolt = <3000000>; regulator-max-microvolt = <3300000>; + regulator-boot-on; /* leave on for snvs power button */ regulator-always-on; }; @@ -753,6 +761,7 @@ regulator-name = "ldo2"; regulator-min-microvolt = <900000>; regulator-max-microvolt = <900000>; + regulator-boot-on; /* leave on for snvs power button */ regulator-always-on; }; @@ -761,6 +770,7 @@ regulator-name = "ldo3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; + regulator-boot-on; regulator-always-on; }; @@ -768,6 +778,7 @@ regulator-name = "ldo4"; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; + regulator-boot-on; regulator-always-on; }; @@ -784,6 +795,7 @@ regulator-name = "ldo6"; regulator-min-microvolt = <900000>; regulator-max-microvolt = <1800000>; + regulator-boot-on; regulator-always-on; }; @@ -792,6 +804,7 @@ regulator-name = "ldo7"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; + regulator-boot-on; regulator-always-on; }; }; From f2047594e865bac597ab5056cd7d573be96ecfe1 Mon Sep 17 00:00:00 2001 From: Martin Kepplinger Date: Mon, 18 Jan 2021 11:54:25 +0100 Subject: [PATCH 397/584] arm64: dts: Add Librem5 Evergreen Add librem5-r4 with specifics to that revision like the near-level, battery and charger properties. For schematics and more information, see https://developer.puri.sm/Librem5/Hardware_Reference/Evergreen.html Signed-off-by: Martin Kepplinger Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../boot/dts/freescale/imx8mq-librem5-r4.dts | 35 +++++++++++++++++++ 2 files changed, 36 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 17fc731da700..44a20b89b1ef 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -49,6 +49,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r4.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts new file mode 100644 index 000000000000..cbfb49aa2563 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts @@ -0,0 +1,35 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +// Copyright (C) 2020 Purism SPC + +/dts-v1/; + +#include "imx8mq-librem5.dtsi" + +/ { + model = "Purism Librem 5r4"; + compatible = "purism,librem5r4", "purism,librem5", "fsl,imx8mq"; +}; + +&accel_gyro { + mount-matrix = "1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; +}; + +&bat { + maxim,rsns-microohm = <1667>; +}; + +&bq25895 { + ti,battery-regulation-voltage = <4200000>; /* uV */ + ti,charge-current = <1500000>; /* uA */ + ti,termination-current = <144000>; /* uA */ +}; + +&led_backlight { + led-max-microamp = <25000>; +}; + +&proximity { + proximity-near-level = <10>; +}; From 47a6ca1172cb516b2a99f4b84ee1491859807390 Mon Sep 17 00:00:00 2001 From: Zhen Lei Date: Mon, 18 Jan 2021 11:16:29 +0800 Subject: [PATCH 398/584] arm64: dts: hisilicon: separate each group of data in the property "ranges" Do not write the "ranges" of multiple groups of data into a uint32 array, use <> to separate them. Otherwise, the errors similar to the following will be reported: soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \ 100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not valid under \ any of the given schemas (Possible causes of the failure): soc: pcie@a0090000:ranges: [[33554432, 0, 2986344448, 0, 2986344448, 0, \ 100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536]] is not of type 'boolean' soc: pcie@a0090000:ranges:0: [33554432, 0, 2986344448, 0, 2986344448, 0, \ 100597760, 16777216, 0, 0, 0, 3086942208, 0, 65536] is too long Signed-off-by: Zhen Lei Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi | 4 ++-- arch/arm64/boot/dts/hisilicon/hip06.dtsi | 5 ++--- arch/arm64/boot/dts/hisilicon/hip07.dtsi | 4 ++-- 3 files changed, 6 insertions(+), 7 deletions(-) diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi index 81d09434c5c6..16e11fde3ed9 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi @@ -565,8 +565,8 @@ device_type = "pci"; bus-range = <0x00 0xff>; num-lanes = <1>; - ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000 - 0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>; + ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000>, + <0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>; interrupts = ; interrupt-names = "msi"; #interrupt-cells = <1>; diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi index 7980709e21ff..78050d67a786 100644 --- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi @@ -737,9 +737,8 @@ #size-cells = <2>; device_type = "pci"; dma-coherent; - ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0 - 0x5ff0000 0x01000000 0 0 0 0xb7ff0000 - 0 0x10000>; + ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0 0x5ff0000>, + <0x01000000 0 0 0 0xb7ff0000 0 0x10000>; #interrupt-cells = <1>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0x0 0 0 1 &mbigen_pcie0 650 4 diff --git a/arch/arm64/boot/dts/hisilicon/hip07.dtsi b/arch/arm64/boot/dts/hisilicon/hip07.dtsi index 7832d9cdec21..f477f442c275 100644 --- a/arch/arm64/boot/dts/hisilicon/hip07.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip07.dtsi @@ -1708,8 +1708,8 @@ #size-cells = <2>; device_type = "pci"; dma-coherent; - ranges = <0x02000000 0 0xa8000000 0 0xa8000000 0 0x77f0000 - 0x01000000 0 0 0 0xaf7f0000 0 0x10000>; + ranges = <0x02000000 0 0xa8000000 0 0xa8000000 0 0x77f0000>, + <0x01000000 0 0 0 0xaf7f0000 0 0x10000>; #interrupt-cells = <1>; interrupt-map-mask = <0xf800 0 0 7>; interrupt-map = <0x0 0 0 1 &mbigen_pcie2_a 671 4 From 1860a51823760f5909e06c40f3b30548df7870fc Mon Sep 17 00:00:00 2001 From: Zhen Lei Date: Mon, 18 Jan 2021 11:16:30 +0800 Subject: [PATCH 399/584] arm64: dts: hisilicon: place clock-names "bus" before "core" Look at the clock-names schema defined in arm,mali-utgard.yaml: clock-names: items: - const: bus - const: core The "bus" needs to be placed before the "core". Signed-off-by: Zhen Lei Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index c6580c9f068e..f9953303a3f4 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -1053,7 +1053,7 @@ "ppmmu3"; clocks = <&media_ctrl HI6220_G3D_CLK>, <&media_ctrl HI6220_G3D_PCLK>; - clock-names = "core", "bus"; + clock-names = "bus", "core"; assigned-clocks = <&media_ctrl HI6220_G3D_CLK>, <&media_ctrl HI6220_G3D_PCLK>; assigned-clock-rates = <500000000>, <144000000>; From dbbf51315a87e3fad6142bdce2278670d3e94e4b Mon Sep 17 00:00:00 2001 From: Zhen Lei Date: Mon, 18 Jan 2021 11:16:31 +0800 Subject: [PATCH 400/584] arm64: dts: hisilicon: normalize the node name of the module thermal 1. Change the node name of the thermal zone to match '^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$', add suffix "-thermal". 2. Change the node name of the trip point to match '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', delete character "@". Signed-off-by: Zhen Lei Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hi3660.dtsi | 6 +++--- arch/arm64/boot/dts/hisilicon/hi6220.dtsi | 6 +++--- 2 files changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi index 49c19c6879f9..cab89dc6f596 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi @@ -1113,7 +1113,7 @@ thermal-zones { - cls0: cls0 { + cls0: cls0-thermal { polling-delay = <1000>; polling-delay-passive = <100>; sustainable-power = <4500>; @@ -1122,13 +1122,13 @@ thermal-sensors = <&tsensor 1>; trips { - threshold: trip-point@0 { + threshold: trip-point0 { temperature = <65000>; hysteresis = <1000>; type = "passive"; }; - target: trip-point@1 { + target: trip-point1 { temperature = <75000>; hysteresis = <1000>; type = "passive"; diff --git a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi index f9953303a3f4..d426c6c8722b 100644 --- a/arch/arm64/boot/dts/hisilicon/hi6220.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi6220.dtsi @@ -872,7 +872,7 @@ thermal-zones { - cls0: cls0 { + cls0: cls0-thermal { polling-delay = <1000>; polling-delay-passive = <100>; sustainable-power = <3326>; @@ -881,13 +881,13 @@ thermal-sensors = <&tsensor 2>; trips { - threshold: trip-point@0 { + threshold: trip-point0 { temperature = <65000>; hysteresis = <0>; type = "passive"; }; - target: trip-point@1 { + target: trip-point1 { temperature = <75000>; hysteresis = <0>; type = "passive"; From a328818ee72a7e9508d9c6347b21bf3198c542c0 Mon Sep 17 00:00:00 2001 From: Zhen Lei Date: Mon, 18 Jan 2021 11:16:32 +0800 Subject: [PATCH 401/584] arm64: dts: hisilicon: normalize the node name of the localbus Change the node name of the localbus to match '^([a-z][a-z0-9\\-]+-bus|bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'. This error is detected by simple-bus.yaml. Signed-off-by: Zhen Lei Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hip05.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/hisilicon/hip05.dtsi b/arch/arm64/boot/dts/hisilicon/hip05.dtsi index 405acaa3e9dd..4aed8d440b3a 100644 --- a/arch/arm64/boot/dts/hisilicon/hip05.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip05.dtsi @@ -318,7 +318,7 @@ status = "disabled"; }; - lbc: localbus@80380000 { + lbc: local-bus@80380000 { compatible = "hisilicon,hisi-localbus", "simple-bus"; reg = <0x0 0x80380000 0x0 0x10000>; status = "disabled"; From b2bbc8687e43df456a6d194bc2c3ab9431b770cb Mon Sep 17 00:00:00 2001 From: Zhen Lei Date: Mon, 18 Jan 2021 11:16:33 +0800 Subject: [PATCH 402/584] arm64: dts: hisilicon: avoid irrelevant nodes being mistakenly identified as PHY nodes Currently, the names of several nodes incorrectly match common PHY provider schema. And the phy-provider.yaml requires them must have property "#phy-cells". As a result, false positives similar to the following are reported: usb2-phy@120: '#phy-cells' is a required property Change their names slightly so that they do not match pattern: "^(|usb-|usb2-|usb3-|pci-|pcie-|sata-)phy(@[0-9a-f,]+)*$". Signed-off-by: Zhen Lei Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi index 16e11fde3ed9..a83b9d4f172e 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi @@ -113,7 +113,7 @@ #size-cells = <1>; ranges = <0x0 0x8a20000 0x1000>; - usb2_phy1: usb2-phy@120 { + usb2_phy1: usb2_phy@120 { compatible = "hisilicon,hi3798cv200-usb2-phy"; reg = <0x120 0x4>; clocks = <&crg HISTB_USB2_PHY1_REF_CLK>; @@ -134,7 +134,7 @@ }; }; - usb2_phy2: usb2-phy@124 { + usb2_phy2: usb2_phy@124 { compatible = "hisilicon,hi3798cv200-usb2-phy"; reg = <0x124 0x4>; clocks = <&crg HISTB_USB2_PHY2_REF_CLK>; From ccf43e02012ae5c2fc895136ab0adf98286db40f Mon Sep 17 00:00:00 2001 From: Zhen Lei Date: Mon, 18 Jan 2021 11:16:34 +0800 Subject: [PATCH 403/584] arm64: dts: hisilicon: delete unused property smmu-cb-memtype The "smmu-cb-memtype" is a private property developed by the Hisilicon driver in the early stage and is not used now. So delete it. Otherwise, below YAML check warnings are reported: arch/arm64/boot/dts/hisilicon/hip06-d03.dt.yaml: iommu@a0040000: \ 'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+' arch/arm64/boot/dts/hisilicon/hip07-d05.dt.yaml: iommu@a0040000: \ 'smmu-cb-memtype' does not match any of the regexes: 'pinctrl-[0-9]+' Signed-off-by: Zhen Lei Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hip06.dtsi | 1 - arch/arm64/boot/dts/hisilicon/hip07.dtsi | 5 ----- 2 files changed, 6 deletions(-) diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi index 78050d67a786..7deca5f763d5 100644 --- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi @@ -335,7 +335,6 @@ reg = <0x0 0xa0040000 0x0 0x20000>; #iommu-cells = <1>; dma-coherent; - smmu-cb-memtype = <0x0 0x1>; hisilicon,broken-prefetch-cmd; status = "disabled"; }; diff --git a/arch/arm64/boot/dts/hisilicon/hip07.dtsi b/arch/arm64/boot/dts/hisilicon/hip07.dtsi index f477f442c275..2172d8071181 100644 --- a/arch/arm64/boot/dts/hisilicon/hip07.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hip07.dtsi @@ -1166,7 +1166,6 @@ reg = <0x0 0xa0040000 0x0 0x20000>; #iommu-cells = <1>; dma-coherent; - smmu-cb-memtype = <0x0 0x1>; hisilicon,broken-prefetch-cmd; status = "disabled"; }; @@ -1181,7 +1180,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; p0_smmu_alg_b: iommu@8d0040000 { compatible = "arm,smmu-v3"; @@ -1194,7 +1192,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; p1_smmu_alg_a: iommu@400d0040000 { compatible = "arm,smmu-v3"; @@ -1207,7 +1204,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; p1_smmu_alg_b: iommu@408d0040000 { compatible = "arm,smmu-v3"; @@ -1220,7 +1216,6 @@ #iommu-cells = <1>; dma-coherent; hisilicon,broken-prefetch-cmd; - /* smmu-cb-memtype = <0x0 0x1>;*/ }; soc { From 305656e0989d45e8dc7273e62130f3dc79d3e2de Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 15 Jan 2021 12:53:56 +0100 Subject: [PATCH 404/584] arm64: dts: hisilicon: hi3670.dtsi: add iomcu_rst This is required in order to support USB. Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi index 85b0dfb35d6d..acf69afb9407 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi @@ -194,6 +194,12 @@ #clock-cells = <1>; }; + iomcu_rst: reset { + compatible = "hisilicon,hi3660-reset"; + hisi,rst-syscon = <&iomcu>; + #reset-cells = <2>; + }; + uart0: serial@fdf02000 { compatible = "arm,pl011", "arm,primecell"; reg = <0x0 0xfdf02000 0x0 0x1000>; From 62b4c3514b8e48658be920bea162b5d7b5f96faa Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 15 Jan 2021 12:53:57 +0100 Subject: [PATCH 405/584] arm64: dts: hisilicon: hikey970-pinctrl.dtsi: add missing pinctrl settings There are several pinctrl settings that are missing at this DT file. Also, the entries are out of order. Add the missing bits, as they'll be required by the DRM driver - and probably by other drivers not upstreamed yet. Reorder the entres, adding the missing bits. Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Wei Xu --- .../boot/dts/hisilicon/hikey970-pinctrl.dtsi | 632 +++++++++++++++++- 1 file changed, 621 insertions(+), 11 deletions(-) diff --git a/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi index d456b0aa6f58..77bd8c3a8314 100644 --- a/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hikey970-pinctrl.dtsi @@ -61,6 +61,153 @@ 0x060 MUX_M1 /* UART6_TXD */ >; }; + + i2c3_pmx_func: i2c3_pmx_func { + pinctrl-single,pins = < + 0x010 MUX_M1 /* I2C3_SCL */ + 0x014 MUX_M1 /* I2C3_SDA */ + >; + }; + + i2c4_pmx_func: i2c4_pmx_func { + pinctrl-single,pins = < + 0x03c MUX_M1 /* I2C4_SCL */ + 0x040 MUX_M1 /* I2C4_SDA */ + >; + }; + + cam0_rst_pmx_func: cam0_rst_pmx_func { + pinctrl-single,pins = < + 0x714 MUX_M0 /* CAM0_RST */ + >; + }; + + cam1_rst_pmx_func: cam1_rst_pmx_func { + pinctrl-single,pins = < + 0x048 MUX_M0 /* CAM1_RST */ + >; + }; + + cam0_pwd_n_pmx_func: cam0_pwd_n_pmx_func { + pinctrl-single,pins = < + 0x098 MUX_M0 /* CAM0_PWD_N */ + >; + }; + + cam1_pwd_n_pmx_func: cam1_pwd_n_pmx_func { + pinctrl-single,pins = < + 0x044 MUX_M0 /* CAM1_PWD_N */ + >; + }; + + isp0_pmx_func: isp0_pmx_func { + pinctrl-single,pins = < + 0x018 MUX_M1 /* ISP_CLK0 */ + 0x024 MUX_M1 /* ISP_SCL0 */ + 0x028 MUX_M1 /* ISP_SDA0 */ + >; + }; + + isp1_pmx_func: isp1_pmx_func { + pinctrl-single,pins = < + 0x01c MUX_M1 /* ISP_CLK1 */ + 0x02c MUX_M1 /* ISP_SCL1 */ + 0x030 MUX_M1 /* ISP_SDA1 */ + >; + }; + }; + + pmx1: pinmux@fff11000 { + compatible = "pinctrl-single"; + reg = <0x0 0xfff11000 0x0 0x73c>; + #gpio-range-cells = <0x3>; + #pinctrl-cells = <1>; + pinctrl-single,register-width = <0x20>; + pinctrl-single,function-mask = <0x7>; + /* pin base, nr pins & gpio function */ + pinctrl-single,gpio-range = <&range 0 46 0>; + + pwr_key_pmx_func: pwr_key_pmx_func { + pinctrl-single,pins = < + 0x064 MUX_M0 /* GPIO_203 */ + >; + }; + + pd_pmx_func: pd_pmx_func{ + pinctrl-single,pins = < + 0x080 MUX_M0 /* GPIO_221 */ + >; + }; + + i2s2_pmx_func: i2s2_pmx_func { + pinctrl-single,pins = < + 0x050 MUX_M1 /* I2S2_DI */ + 0x054 MUX_M1 /* I2S2_DO */ + 0x058 MUX_M1 /* I2S2_XCLK */ + 0x05c MUX_M1 /* I2S2_XFS */ + >; + }; + + spi0_pmx_func: spi0_pmx_func { + pinctrl-single,pins = < + 0x094 MUX_M1 /* SPI0_CLK */ + 0x098 MUX_M1 /* SPI0_DI */ + 0x09c MUX_M1 /* SPI0_DO */ + 0x0a0 MUX_M1 /* SPI0_CS0_N */ + >; + }; + + spi2_pmx_func: spi2_pmx_func { + pinctrl-single,pins = < + 0x710 MUX_M1 /* SPI2_CLK */ + 0x714 MUX_M1 /* SPI2_DI */ + 0x718 MUX_M1 /* SPI2_DO */ + 0x71c MUX_M1 /* SPI2_CS0_N */ + >; + }; + + spi3_pmx_func: spi3_pmx_func { + pinctrl-single,pins = < + 0x72c MUX_M1 /* SPI3_CLK */ + 0x730 MUX_M1 /* SPI3_DI */ + 0x734 MUX_M1 /* SPI3_DO */ + 0x738 MUX_M1 /* SPI3_CS0_N */ + >; + }; + + i2c0_pmx_func: i2c0_pmx_func { + pinctrl-single,pins = < + 0x020 MUX_M1 /* I2C0_SCL */ + 0x024 MUX_M1 /* I2C0_SDA */ + >; + }; + + i2c1_pmx_func: i2c1_pmx_func { + pinctrl-single,pins = < + 0x028 MUX_M1 /* I2C1_SCL */ + 0x02c MUX_M1 /* I2C1_SDA */ + >; + }; + i2c2_pmx_func: i2c2_pmx_func { + pinctrl-single,pins = < + 0x030 MUX_M1 /* I2C2_SCL */ + 0x034 MUX_M1 /* I2C2_SDA */ + >; + }; + + pcie_clkreq_pmx_func: pcie_clkreq_pmx_func { + pinctrl-single,pins = < + 0x084 MUX_M1 /* PCIE0_CLKREQ_N */ + >; + }; + + gpio185_pmx_func: gpio185_pmx_func { + pinctrl-single,pins = <0x01C 0x1>; + }; + + gpio185_pmx_idle: gpio185_pmx_idle { + pinctrl-single,pins = <0x01C 0x0>; + }; }; pmx2: pinmux@e896c800 { @@ -184,6 +331,180 @@ DRIVE7_02MA DRIVE6_MASK >; }; + + i2c3_cfg_func: i2c3_cfg_func { + pinctrl-single,pins = < + 0x014 0x0 /* I2C3_SCL */ + 0x018 0x0 /* I2C3_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + i2c4_cfg_func: i2c4_cfg_func { + pinctrl-single,pins = < + 0x040 0x0 /* I2C4_SCL */ + 0x044 0x0 /* I2C4_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam0_rst_cfg_func: cam0_rst_cfg_func { + pinctrl-single,pins = < + 0x714 0x0 /* CAM0_RST */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam1_rst_cfg_func: cam1_rst_cfg_func { + pinctrl-single,pins = < + 0x04C 0x0 /* CAM1_RST */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam0_pwd_n_cfg_func: cam0_pwd_n_cfg_func { + pinctrl-single,pins = < + 0x09C 0x0 /* CAM0_PWD_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + cam1_pwd_n_cfg_func: cam1_pwd_n_cfg_func { + pinctrl-single,pins = < + 0x048 0x0 /* CAM1_PWD_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + isp0_cfg_func: isp0_cfg_func { + pinctrl-single,pins = < + 0x01C 0x0 /* ISP_CLK0 */ + 0x028 0x0 /* ISP_SCL0 */ + 0x02C 0x0 /* ISP_SDA0 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + isp1_cfg_func: isp1_cfg_func { + pinctrl-single,pins = < + 0x020 0x0 /* ISP_CLK1 */ + 0x030 0x0 /* ISP_SCL1 */ + 0x034 0x0 /* ISP_SDA1 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; }; pmx5: pinmux@fc182000 { @@ -338,22 +659,311 @@ }; }; - pmx1: pinmux@fff11000 { - compatible = "pinctrl-single"; - reg = <0x0 0xfff11000 0x0 0x73c>; - #gpio-range-cells = <0x3>; - #pinctrl-cells = <1>; - pinctrl-single,register-width = <0x20>; - pinctrl-single,function-mask = <0x7>; - /* pin base, nr pins & gpio function */ - pinctrl-single,gpio-range = <&range 0 46 0>; - }; - pmx16: pinmux@fff11800 { compatible = "pinconf-single"; reg = <0x0 0xfff11800 0x0 0x73c>; #pinctrl-cells = <1>; pinctrl-single,register-width = <0x20>; + + pwr_key_cfg_func: pwr_key_cfg_func { + pinctrl-single,pins = < + 0x090 0x0 /* GPIO_203 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_02MA DRIVE6_MASK + >; + }; + + usb_cfg_func: usb_cfg_func { + pinctrl-single,pins = < + 0x0AC 0x0 /* GPIO_221 */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_02MA DRIVE6_MASK + >; + }; + + spi0_cfg_func: spi0_cfg_func { + pinctrl-single,pins = < + 0x0c8 0x0 /* SPI0_DI */ + 0x0cc 0x0 /* SPI0_DO */ + 0x0d0 0x0 /* SPI0_CS0_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + + spi2_cfg_func: spi2_cfg_func { + pinctrl-single,pins = < + 0x714 0x0 /* SPI2_DI */ + 0x718 0x0 /* SPI2_DO */ + 0x71c 0x0 /* SPI2_CS0_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + + spi3_cfg_func: spi3_cfg_func { + pinctrl-single,pins = < + 0x730 0x0 /* SPI3_DI */ + 0x734 0x0 /* SPI3_DO */ + 0x738 0x0 /* SPI3_CS0_N */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + + spi0_clk_cfg_func: spi0_clk_cfg_func { + pinctrl-single,pins = < + 0x0c4 0x0 /* SPI0_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_10MA DRIVE6_MASK + >; + }; + + spi2_clk_cfg_func: spi2_clk_cfg_func { + pinctrl-single,pins = < + 0x710 0x0 /* SPI2_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_10MA DRIVE6_MASK + >; + }; + + spi3_clk_cfg_func: spi3_clk_cfg_func { + pinctrl-single,pins = < + 0x72c 0x0 /* SPI3_CLK */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_10MA DRIVE6_MASK + >; + }; + + i2c0_cfg_func: i2c0_cfg_func { + pinctrl-single,pins = < + 0x04c 0x0 /* I2C0_SCL */ + 0x050 0x0 /* I2C0_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + i2c1_cfg_func: i2c1_cfg_func { + pinctrl-single,pins = < + 0x054 0x0 /* I2C1_SCL */ + 0x058 0x0 /* I2C1_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + i2c2_cfg_func: i2c2_cfg_func { + pinctrl-single,pins = < + 0x05c 0x0 /* I2C2_SCL */ + 0x060 0x0 /* I2C2_SDA */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_04MA DRIVE6_MASK + >; + }; + + pcie_clkreq_cfg_func: pcie_clkreq_cfg_func { + pinctrl-single,pins = < + 0x0b0 0x0 + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_DIS + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_06MA DRIVE6_MASK + >; + }; + i2s2_cfg_func: i2s2_cfg_func { + pinctrl-single,pins = < + 0x07c 0x0 /* I2S2_DI */ + 0x080 0x0 /* I2S2_DO */ + 0x084 0x0 /* I2S2_XCLK */ + 0x088 0x0 /* I2S2_XFS */ + >; + pinctrl-single,bias-pulldown = < + PULL_DIS + PULL_DOWN + PULL_DIS + PULL_DOWN + >; + pinctrl-single,bias-pullup = < + PULL_UP + PULL_UP + PULL_DIS + PULL_UP + >; + pinctrl-single,drive-strength = < + DRIVE7_02MA DRIVE6_MASK + >; + }; + + gpio185_cfg_func: gpio185_cfg_func { + pinctrl-single,pins = <0x048 0>; + pinctrl-single,bias-pulldown = <0 2 0 2>; + pinctrl-single,bias-pullup = <0 1 0 1>; + pinctrl-single,drive-strength = <0x00 0x70>; + pinctrl-single,slew-rate = <0x0 0x80>; + }; + + gpio185_cfg_idle: gpio185_cfg_idle { + pinctrl-single,pins = <0x048 0>; + pinctrl-single,bias-pulldown = <2 2 0 2>; + pinctrl-single,bias-pullup = <0 1 0 1>; + pinctrl-single,drive-strength = <0x00 0x70>; + pinctrl-single,slew-rate = <0x0 0x80>; + }; }; }; }; From b6e141eec86b730dfeddb888af7d3e0247530ef1 Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Fri, 15 Jan 2021 12:53:58 +0100 Subject: [PATCH 406/584] arm64: dts: hisilicon: hi3670.dtsi: add I2C settings The I2C buses are not declared at the device tree. As this will be needed by further patches, add them, keeping all in disabled state. Per-board settings can override it. Signed-off-by: Mauro Carvalho Chehab Signed-off-by: Wei Xu --- arch/arm64/boot/dts/hisilicon/hi3670.dtsi | 71 +++++++++++++++++++++++ 1 file changed, 71 insertions(+) diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi index acf69afb9407..8830795c8efc 100644 --- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi +++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi @@ -714,5 +714,76 @@ card-detect-delay = <200>; status = "disabled"; }; + + /* I2C */ + i2c0: i2c@ffd71000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xffd71000 0x0 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&iomcu HI3670_CLK_GATE_I2C0>; + resets = <&iomcu_rst 0x20 3>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pmx_func &i2c0_cfg_func>; + status = "disabled"; + }; + + i2c1: i2c@ffd72000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xffd72000 0x0 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&iomcu HI3670_CLK_GATE_I2C1>; + resets = <&iomcu_rst 0x20 4>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pmx_func &i2c1_cfg_func>; + status = "disabled"; + }; + + i2c2: i2c@ffd73000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xffd73000 0x0 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&iomcu HI3670_CLK_GATE_I2C2>; + resets = <&iomcu_rst 0x20 5>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pmx_func &i2c2_cfg_func>; + status = "disabled"; + }; + + i2c3: i2c@fdf0c000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xfdf0c000 0x0 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&crg_ctrl HI3670_CLK_GATE_I2C3>; + resets = <&crg_rst 0x78 7>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pmx_func &i2c3_cfg_func>; + status = "disabled"; + }; + + i2c4: i2c@fdf0d000 { + compatible = "snps,designware-i2c"; + reg = <0x0 0xfdf0d000 0x0 0x1000>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + clock-frequency = <400000>; + clocks = <&crg_ctrl HI3670_CLK_GATE_I2C4>; + resets = <&crg_rst 0x78 27>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pmx_func &i2c4_cfg_func>; + status = "disabled"; + }; }; }; From 189f65864f4eeb430bee0e6a18b7f871bf218878 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Tue, 19 Jan 2021 07:42:57 -0600 Subject: [PATCH 407/584] arm64: dts: imx8mn: Add fspi node The i.MX8M Nano has the same Flexspi controller used in the i.MX8M Mini. Add the node and disable it by default. Signed-off-by: Adam Ford Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mn.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi index 8004b7f36c77..d0c6f7aca8bc 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi @@ -889,6 +889,19 @@ status = "disabled"; }; + flexspi: spi@30bb0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "nxp,imx8mm-fspi"; + reg = <0x30bb0000 0x10000>, <0x8000000 0x10000000>; + reg-names = "fspi_base", "fspi_mmap"; + interrupts = ; + clocks = <&clk IMX8MN_CLK_QSPI_ROOT>, + <&clk IMX8MN_CLK_QSPI_ROOT>; + clock-names = "fspi", "fspi_en"; + status = "disabled"; + }; + sdma1: dma-controller@30bd0000 { compatible = "fsl,imx8mn-sdma", "fsl,imx8mq-sdma"; reg = <0x30bd0000 0x10000>; From 738f7d40c155ccf0c5564f3d1dce02bea3b09eb1 Mon Sep 17 00:00:00 2001 From: Adam Ford Date: Tue, 19 Jan 2021 07:42:58 -0600 Subject: [PATCH 408/584] arm64: dts: imx8mn-beacon-som: Enable QSPI on SOM There is a QSPI chip connected to the FlexSPI bus. Enable it. Signed-off-by: Adam Ford Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- .../boot/dts/freescale/imx8mn-beacon-som.dtsi | 28 +++++++++++++++++++ 1 file changed, 28 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi index 2120e6485393..de2cd0e3201c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi @@ -7,6 +7,7 @@ aliases { rtc0 = &rtc; rtc1 = &snvs_rtc; + spi0 = &flexspi; }; usdhc1_pwrseq: usdhc1_pwrseq { @@ -89,6 +90,22 @@ }; }; +&flexspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexspi>; + status = "okay"; + + flash@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <80000000>; + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + }; +}; + &i2c1 { clock-frequency = <400000>; pinctrl-names = "default"; @@ -318,6 +335,17 @@ >; }; + pinctrl_flexspi: flexspigrp { + fsl,pins = < + MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 + MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 + MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 + MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 + MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 + MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 + >; + }; + pinctrl_pmic: pmicirqgrp { fsl,pins = < MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141 From 1ab66ad2d7f32de2e553213f2d7afc1158a59d3e Mon Sep 17 00:00:00 2001 From: Pawel Dembicki Date: Tue, 19 Jan 2021 16:51:05 +0100 Subject: [PATCH 409/584] arm64: dts: fsl-ls1012a-rdb: add i2c devices LS1012A-RDB equipped in some i2c devices: - 3x GPIO Expander: PCAL9555A (NXP) - Gyro: FXAS21002 (NXP) - Accelerometer: FXOS8700 (NXP) - Current & Power Monitor: INA220 (TI) This patch add listed devices to dts. Signed-off-by: Pawel Dembicki Signed-off-by: Shawn Guo --- .../boot/dts/freescale/fsl-ls1012a-rdb.dts | 45 +++++++++++++++++++ 1 file changed, 45 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts index f939d656898b..79f155dedb2d 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts @@ -7,6 +7,7 @@ */ /dts-v1/; +#include #include "fsl-ls1012a.dtsi" / { @@ -38,6 +39,50 @@ &i2c0 { status = "okay"; + + accelerometer@1e { + compatible = "nxp,fxos8700"; + reg = <0x1e>; + interrupt-parent = <&gpio26>; + interrupts = <13 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "INT1"; + }; + + gyroscope@20 { + compatible = "nxp,fxas21002c"; + reg = <0x20>; + }; + + gpio@24 { + compatible = "nxp,pcal9555a"; + reg = <0x24>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio@25 { + compatible = "nxp,pcal9555a"; + reg = <0x25>; + gpio-controller; + #gpio-cells = <2>; + }; + + gpio26: gpio@26 { + compatible = "nxp,pcal9555a"; + reg = <0x26>; + interrupt-parent = <&gpio0>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + }; + + current-sensor@40 { + compatible = "ti,ina220"; + reg = <0x40>; + shunt-resistor = <2000>; + }; }; &qspi { From 42c2c068834eab53621a869bd85dac3a915e059c Mon Sep 17 00:00:00 2001 From: Pawel Dembicki Date: Tue, 19 Jan 2021 16:51:06 +0100 Subject: [PATCH 410/584] arm64: dts: fsl-ls1012a-frdm: add spi-uart device This patch adds spi-uart controller to LS1012A-FRDM board dts. Device is equipped in SC16IS740 from NXP. Signed-off-by: Pawel Dembicki Signed-off-by: Shawn Guo --- .../boot/dts/freescale/fsl-ls1012a-frdm.dts | 21 +++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts index 67702667ed8a..2517528f684f 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dts @@ -7,6 +7,7 @@ */ /dts-v1/; +#include #include "fsl-ls1012a.dtsi" / { @@ -57,6 +58,26 @@ }; }; +&dspi { + bus-num = <0>; + status = "okay"; + + serial@0 { + compatible = "nxp,sc16is740"; + reg = <0>; + spi-max-frequency = <4000000>; + clocks = <&sc16is7xx_clk>; + interrupt-parent = <&gpio1>; + interrupts = <13 IRQ_TYPE_EDGE_FALLING>; + + sc16is7xx_clk: clock-sc16is7xx { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + }; + }; +}; + &duart0 { status = "okay"; }; From 4daff3e5b42422cd4af758cc7768223d2b7f6e14 Mon Sep 17 00:00:00 2001 From: Rosen Penev Date: Fri, 4 Dec 2020 16:54:36 -0800 Subject: [PATCH 411/584] ARM: dts: armada-385-linksys: fix usage with newer devices Newer Linksys boards might come with a Winbond W29N02GV which can be configured in different ways. Make sure we configure it the same way as the older chips so everything keeps working. Signed-off-by: Imre Kaloz Signed-off-by: Rosen Penev Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-385-linksys.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi index 827e82be2201..fb9c8a0b241c 100644 --- a/arch/arm/boot/dts/armada-385-linksys.dtsi +++ b/arch/arm/boot/dts/armada-385-linksys.dtsi @@ -148,6 +148,8 @@ reg = <0>; label = "pxa3xx_nand-0"; nand-rb = <0>; + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; marvell,nand-keep-config; nand-on-flash-bbt; }; From e011c9025a4691b5c734029577a920bd6c320994 Mon Sep 17 00:00:00 2001 From: Rosen Penev Date: Wed, 2 Dec 2020 18:23:20 -0800 Subject: [PATCH 412/584] ARM: dts: armada388-helios4: assign pinctrl to LEDs Split up the pins to match earlier definitions. Allows LEDs to flash properly. Fixes: ced8025b569e ("ARM: dts: armada388-helios4") Signed-off-by: Rosen Penev Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-388-helios4.dts | 15 ++++++++++++--- 1 file changed, 12 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts index b3728de3bd3f..5a6af7e83e44 100644 --- a/arch/arm/boot/dts/armada-388-helios4.dts +++ b/arch/arm/boot/dts/armada-388-helios4.dts @@ -70,6 +70,9 @@ system-leds { compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&helios_system_led_pins>; + status-led { label = "helios4:green:status"; gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; @@ -86,6 +89,9 @@ io-leds { compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&helios_io_led_pins>; + sata1-led { label = "helios4:green:ata1"; gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; @@ -286,9 +292,12 @@ "mpp39", "mpp40"; marvell,function = "sd0"; }; - helios_led_pins: helios-led-pins { - marvell,pins = "mpp24", "mpp25", - "mpp49", "mpp50", + helios_system_led_pins: helios-system-led-pins { + marvell,pins = "mpp24", "mpp25"; + marvell,function = "gpio"; + }; + helios_io_led_pins: helios-io-led-pins { + marvell,pins = "mpp49", "mpp50", "mpp52", "mpp53", "mpp54"; marvell,function = "gpio"; From 46ecdfc1830eaa40a11d7f832089c82b0e67ea96 Mon Sep 17 00:00:00 2001 From: Rosen Penev Date: Wed, 2 Dec 2020 18:23:21 -0800 Subject: [PATCH 413/584] ARM: dts: armada388-helios4: assign pinctrl to each fan Split up the pins for each fan. This is needed in order to control them Fixes: ced8025b569e ("ARM: dts: armada388-helios4") Signed-off-by: Rosen Penev Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-388-helios4.dts | 13 ++++++++++--- 1 file changed, 10 insertions(+), 3 deletions(-) diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts index 5a6af7e83e44..ec134e22bae3 100644 --- a/arch/arm/boot/dts/armada-388-helios4.dts +++ b/arch/arm/boot/dts/armada-388-helios4.dts @@ -127,11 +127,15 @@ fan1: j10-pwm { compatible = "pwm-fan"; pwms = <&gpio1 9 40000>; /* Target freq:25 kHz */ + pinctrl-names = "default"; + pinctrl-0 = <&helios_fan1_pins>; }; fan2: j17-pwm { compatible = "pwm-fan"; pwms = <&gpio1 23 40000>; /* Target freq:25 kHz */ + pinctrl-names = "default"; + pinctrl-0 = <&helios_fan2_pins>; }; usb2_phy: usb2-phy { @@ -302,9 +306,12 @@ "mpp54"; marvell,function = "gpio"; }; - helios_fan_pins: helios-fan-pins { - marvell,pins = "mpp41", "mpp43", - "mpp48", "mpp55"; + helios_fan1_pins: helios_fan1_pins { + marvell,pins = "mpp41", "mpp43"; + marvell,function = "gpio"; + }; + helios_fan2_pins: helios_fan2_pins { + marvell,pins = "mpp48", "mpp55"; marvell,function = "gpio"; }; microsom_spi1_cs_pins: spi1-cs-pins { From a9d9bfcadfb43b856dbcf9419de75f7420d5a225 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marek=20Beh=C3=BAn?= Date: Mon, 11 Jan 2021 03:12:43 +0100 Subject: [PATCH 414/584] arm64: dts: armada-3720-turris-mox: rename u-boot mtd partition to a53-firmware MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The partition called "u-boot" in reality contains TF-A and U-Boot, and TF-A is before U-Boot. Rename this parition to "a53-firmware" to avoid confusion for users, since they cannot simply build U-Boot from U-Boot repository and flash the resulting image there. Instead they have to build the firmware with the sources from the mox-boot-builder repository [1] and flash the a53-firmware.bin binary there. [1] https://gitlab.nic.cz/turris/mox-boot-builder Signed-off-by: Marek Behún Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox") Cc: Gregory CLEMENT Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts index f5ec3b644769..d239ab70ed99 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts @@ -205,7 +205,7 @@ }; partition@20000 { - label = "u-boot"; + label = "a53-firmware"; reg = <0x20000 0x160000>; }; From 6c55091335213faf42eaf4c17614cc15ef70e735 Mon Sep 17 00:00:00 2001 From: Konstantin Porotchkin Date: Tue, 12 Jan 2021 11:46:54 +0200 Subject: [PATCH 415/584] arm64: dts: change AP807 SDHCI compatibility string This patch adds new compatible string to AP807 DTSI to avoid its SDHCI controller to run in "slow mode" with disabled UHS. Signed-off-by: Marcin Wojtas Signed-off-by: Konstantin Porotchkin Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-ap807.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-ap807.dtsi b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi index 623010f3ca89..d9bbbfa4b4eb 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap807.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap807.dtsi @@ -27,3 +27,8 @@ #clock-cells = <1>; }; }; + +&ap_sdhci0 { + compatible = "marvell,armada-ap807-sdhci"; +}; + From e8ff9d5996ac865982319cd44be9cf0515d31f82 Mon Sep 17 00:00:00 2001 From: Marcin Wojtas Date: Tue, 12 Jan 2021 11:46:55 +0200 Subject: [PATCH 416/584] arm64: dts: cn913x-db: enable MMC HS400 This patch adds necessary flags in the device tree which enable HS400 mode on AP807 MMC controller on the CN913x-DB board. Signed-off-by: Marcin Wojtas Signed-off-by: Konstantin Porotchkin Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts index ce49a70d88a0..79020e6d2792 100644 --- a/arch/arm64/boot/dts/marvell/cn9130-db.dts +++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts @@ -113,6 +113,8 @@ &ap_sdhci0 { pinctrl-names = "default"; bus-width = <8>; + mmc-ddr-1_8v; + mmc-hs400-1_8v; vqmmc-supply = <&ap0_reg_sd_vccq>; status = "okay"; }; From 6ece0f7dbd558670ec72ba390379949a4d4dc5c0 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Pali=20Roh=C3=A1r?= Date: Mon, 18 Jan 2021 10:31:39 +0100 Subject: [PATCH 417/584] arm64: dts: marvell: armada-37xx: Add SATA comphy into main armada-37xx.dtsi file MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit SATA on A3720 SOC can use only comphy2, so move this definition from board specific DTS file armada-3720-espressobin.dtsi into main A3720 SOC file armada-37xx.dtsi. Signed-off-by: Pali Rohár Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi | 2 -- arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 2 ++ 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi index daffe136c523..5fc613d24151 100644 --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dtsi @@ -67,8 +67,6 @@ /* J6 */ &sata { status = "okay"; - phys = <&comphy2 0>; - phy-names = "sata-phy"; }; /* U11 */ diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi index d5b6c0a1c54a..7a2df148c6a3 100644 --- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi @@ -458,6 +458,8 @@ reg = <0xe0000 0x178>; interrupts = ; clocks = <&nb_periph_clk 1>; + phys = <&comphy2 0>; + phy-names = "sata-phy"; status = "disabled"; }; From 35db5e32ebc16330ae6275c24783efa4091af1bc Mon Sep 17 00:00:00 2001 From: Baruch Siach Date: Mon, 11 Jan 2021 13:46:28 +0200 Subject: [PATCH 418/584] arm64: dts: armada: add pwm offsets for ap/cp gpios The 'marvell,pwm-offset' property of both GPIO blocks (per CP component) point to the same counter registers offset. The driver will decide how to use counters A/B. This is different from the convention of pwm on earlier Armada series (370/38x). On those systems the assignment of A/B counters to GPIO blocks is coded in both DT and the driver. The actual behaviour of the current driver on Armada 8K/7K is the same as earlier systems. Add also clock properties for base pwm frequency reference. Signed-off-by: Baruch Siach Signed-off-by: Gregory CLEMENT --- arch/arm64/boot/dts/marvell/armada-ap80x.dtsi | 3 +++ arch/arm64/boot/dts/marvell/armada-cp11x.dtsi | 10 ++++++++++ 2 files changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi index 12e477f1aeb9..6614472100c2 100644 --- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi @@ -281,6 +281,9 @@ gpio-controller; #gpio-cells = <2>; gpio-ranges = <&ap_pinctrl 0 0 20>; + marvell,pwm-offset = <0x10c0>; + #pwm-cells = <2>; + clocks = <&ap_clk 3>; }; }; diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi index 994a2fce449a..d774a39334d9 100644 --- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi +++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi @@ -234,12 +234,17 @@ gpio-controller; #gpio-cells = <2>; gpio-ranges = <&CP11X_LABEL(pinctrl) 0 0 32>; + marvell,pwm-offset = <0x1f0>; + #pwm-cells = <2>; interrupt-controller; interrupts = <86 IRQ_TYPE_LEVEL_HIGH>, <85 IRQ_TYPE_LEVEL_HIGH>, <84 IRQ_TYPE_LEVEL_HIGH>, <83 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; + clock-names = "core", "axi"; + clocks = <&CP11X_LABEL(clk) 1 21>, + <&CP11X_LABEL(clk) 1 17>; status = "disabled"; }; @@ -250,12 +255,17 @@ gpio-controller; #gpio-cells = <2>; gpio-ranges = <&CP11X_LABEL(pinctrl) 0 32 31>; + marvell,pwm-offset = <0x1f0>; + #pwm-cells = <2>; interrupt-controller; interrupts = <82 IRQ_TYPE_LEVEL_HIGH>, <81 IRQ_TYPE_LEVEL_HIGH>, <80 IRQ_TYPE_LEVEL_HIGH>, <79 IRQ_TYPE_LEVEL_HIGH>; #interrupt-cells = <2>; + clock-names = "core", "axi"; + clocks = <&CP11X_LABEL(clk) 1 21>, + <&CP11X_LABEL(clk) 1 17>; status = "disabled"; }; }; From 6c50321fd65135a28450f16b5745b72368d61006 Mon Sep 17 00:00:00 2001 From: Thierry Reding Date: Thu, 28 Jan 2021 19:29:40 +0100 Subject: [PATCH 419/584] dt-bindings: arm: tegra: Document Jetson Xavier NX eMMC SKU Two different SKUs exist for the Jetson Xavier NX module, so document the compatible strings for both, as well as the developer kits that come with each of the SKUs. Signed-off-by: Thierry Reding --- Documentation/devicetree/bindings/arm/tegra.yaml | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/tegra.yaml b/Documentation/devicetree/bindings/arm/tegra.yaml index c5fbf869aa93..b9f75e20fef5 100644 --- a/Documentation/devicetree/bindings/arm/tegra.yaml +++ b/Documentation/devicetree/bindings/arm/tegra.yaml @@ -120,10 +120,18 @@ properties: items: - const: nvidia,p3668-0000 - const: nvidia,tegra194 + - description: Jetson Xavier NX (eMMC) + items: + - const: nvidia,p3668-0001 + - const: nvidia,tegra194 - description: Jetson Xavier NX Developer Kit items: - const: nvidia,p3509-0000+p3668-0000 - const: nvidia,tegra194 + - description: Jetson Xavier NX Developer Kit (eMMC) + items: + - const: nvidia,p3509-0000+p3668-0001 + - const: nvidia,tegra194 - items: - enum: - nvidia,tegra234-vdk From 3029a563ac0ccd39b9dc53eadfb9c0e3fb57a449 Mon Sep 17 00:00:00 2001 From: Peter Geis Date: Thu, 7 Jan 2021 16:56:59 +0000 Subject: [PATCH 420/584] ARM: tegra: ouya: Fix eMMC on specific bootloaders Ouya fails to detect the eMMC module when booted via certain bootloaders. Fastboot and hard-kexec bootloaders fail while u-boot does not. It was discovered that the issue manifests if the sdmmc4 alternate configuration clock pin is input disabled. Ouya uses sdmmc4 in the primary pin configuration. It is unknown why this occurs, though it is likely related to other eMMC limitations experienced on Ouya. For now, fix it by enabling input on cam_mclk_pcc0. Fixes: d7195ac5c9c5 ("ARM: tegra: Add device-tree for Ouya") Reported-by: Matt Merhar Tested-by: Matt Merhar Signed-off-by: Peter Geis Acked-by: Thierry Reding Signed-off-by: Thierry Reding --- arch/arm/boot/dts/tegra30-ouya.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/tegra30-ouya.dts b/arch/arm/boot/dts/tegra30-ouya.dts index 74da1360d297..0368b3b816ef 100644 --- a/arch/arm/boot/dts/tegra30-ouya.dts +++ b/arch/arm/boot/dts/tegra30-ouya.dts @@ -4352,8 +4352,8 @@ nvidia,pins = "cam_mclk_pcc0"; nvidia,function = "vi_alt3"; nvidia,pull = ; - nvidia,tristate = ; - nvidia,enable-input = ; + nvidia,tristate = ; + nvidia,enable-input = ; }; pcc1 { nvidia,pins = "pcc1"; From afca1c66fb3312ddf58b92dd24ac378d6d4f6079 Mon Sep 17 00:00:00 2001 From: Fabien Parent Date: Wed, 9 Dec 2020 13:03:20 +0100 Subject: [PATCH 421/584] arm64: dts: mediatek: mt8183: add pwm node MT8183 SoC has 4 PWMs. Add the pwm node in order to support them. Signed-off-by: Fabien Parent Link: https://lore.kernel.org/r/20201209120322.137610-1-fparent@baylibre.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index 64fbba76597c..f4d0f5de99b9 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -668,6 +668,20 @@ clock-names = "main", "mm"; }; + pwm1: pwm@11006000 { + compatible = "mediatek,mt8183-pwm"; + reg = <0 0x11006000 0 0x1000>; + #pwm-cells = <2>; + clocks = <&infracfg CLK_INFRA_PWM>, + <&infracfg CLK_INFRA_PWM_HCLK>, + <&infracfg CLK_INFRA_PWM1>, + <&infracfg CLK_INFRA_PWM2>, + <&infracfg CLK_INFRA_PWM3>, + <&infracfg CLK_INFRA_PWM4>; + clock-names = "top", "main", "pwm1", "pwm2", "pwm3", + "pwm4"; + }; + i2c3: i2c@1100f000 { compatible = "mediatek,mt8183-i2c"; reg = <0 0x1100f000 0 0x1000>, From 06ec50ec0ee97911263d63b172d61dd97ac6c89b Mon Sep 17 00:00:00 2001 From: Fabien Parent Date: Wed, 9 Dec 2020 13:03:21 +0100 Subject: [PATCH 422/584] arm64: dts: mediatek: mt8183-evb: add PWM support Enable the pwm driver and set the pinctrl for PWM A line. Signed-off-by: Fabien Parent Link: https://lore.kernel.org/r/20201209120322.137610-2-fparent@baylibre.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183-evb.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts index cba2d8933e79..3249c959f76f 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts +++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts @@ -344,6 +344,12 @@ bias-disable; }; }; + + pwm_pins_1: pwm1 { + pins_pwm { + pinmux = ; + }; + }; }; &spi0 { @@ -392,3 +398,9 @@ &uart0 { status = "okay"; }; + +&pwm1 { + status = "okay"; + pinctrl-0 = <&pwm_pins_1>; + pinctrl-names = "default"; +}; From 3032985a01f499ec5a5e0d0aca3b2b9f35dbd26c Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Fri, 29 Jan 2021 17:11:07 +0530 Subject: [PATCH 423/584] arm64: tegra: Add RT5658 device entry Jetson AGX Xavier has an on-board audio codec whicn is connected to Tegra I2S1 interface. Hence add corresponding device node for the audio codec. Signed-off-by: Sameer Pujar Reviewed-by: Jon Hunter Signed-off-by: Thierry Reding --- .../arm64/boot/dts/nvidia/tegra194-p2972-0000.dts | 15 +++++++++++++++ 1 file changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts index 8697927b1fe7..f77f87c33e74 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts @@ -134,6 +134,21 @@ phy-names = "usb2-0", "usb2-1", "usb2-3", "usb3-0", "usb3-2", "usb3-3"; }; + i2c@c250000 { + status = "okay"; + + rt5658: audio-codec@1a { + status = "okay"; + + compatible = "realtek,rt5658"; + reg = <0x1a>; + interrupt-parent = <&gpio>; + interrupts = ; + realtek,jd-src = <2>; + sound-name-prefix = "CVB-RT"; + }; + }; + pwm@c340000 { status = "okay"; }; From 5d25c476f252d87e7dd7649bf9c2101b53f0b043 Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Fri, 29 Jan 2021 17:11:08 +0530 Subject: [PATCH 424/584] Revert "arm64: tegra: Disable the ACONNECT for Jetson TX2" This reverts commit fb319496935b ("arm64: tegra: Disable the ACONNECT for Jetson TX2"). Signed-off-by: Sameer Pujar Signed-off-by: Thierry Reding --- arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts | 12 ++++++++++++ 1 file changed, 12 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts index 6fd2e0542c27..7e1723e765b8 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts @@ -10,6 +10,18 @@ model = "NVIDIA Jetson TX2 Developer Kit"; compatible = "nvidia,p2771-0000", "nvidia,tegra186"; + aconnect { + status = "okay"; + + dma-controller@2930000 { + status = "okay"; + }; + + interrupt-controller@2a40000 { + status = "okay"; + }; + }; + i2c@3160000 { power-monitor@42 { compatible = "ti,ina3221"; From e4710376353c1b55326f259e5454584c676ef896 Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Fri, 29 Jan 2021 17:11:09 +0530 Subject: [PATCH 425/584] arm64: tegra: Audio graph sound card for Jetson TX2 Enable support for audio-graph based sound card on Jetson TX2. Based on the board design following I/O modules are enabled. * All I2S instances (I2S1 ... I2S6) * All DSPK instances (DSPK1, DSPK2) * DMIC1, DMIC2 and DMIC3 Signed-off-by: Sameer Pujar Signed-off-by: Thierry Reding --- .../boot/dts/nvidia/tegra186-p2771-0000.dts | 730 ++++++++++++++++++ arch/arm64/boot/dts/nvidia/tegra186.dtsi | 22 + 2 files changed, 752 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts index 7e1723e765b8..9f5f5e1fa82e 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts @@ -20,6 +20,713 @@ interrupt-controller@2a40000 { status = "okay"; }; + + ahub@2900800 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + + xbar_admaif0_ep: endpoint { + remote-endpoint = <&admaif0_ep>; + }; + }; + + port@1 { + reg = <0x1>; + + xbar_admaif1_ep: endpoint { + remote-endpoint = <&admaif1_ep>; + }; + }; + + port@2 { + reg = <0x2>; + + xbar_admaif2_ep: endpoint { + remote-endpoint = <&admaif2_ep>; + }; + }; + + port@3 { + reg = <0x3>; + + xbar_admaif3_ep: endpoint { + remote-endpoint = <&admaif3_ep>; + }; + }; + + port@4 { + reg = <0x4>; + + xbar_admaif4_ep: endpoint { + remote-endpoint = <&admaif4_ep>; + }; + }; + + port@5 { + reg = <0x5>; + + xbar_admaif5_ep: endpoint { + remote-endpoint = <&admaif5_ep>; + }; + }; + + port@6 { + reg = <0x6>; + + xbar_admaif6_ep: endpoint { + remote-endpoint = <&admaif6_ep>; + }; + }; + + port@7 { + reg = <0x7>; + + xbar_admaif7_ep: endpoint { + remote-endpoint = <&admaif7_ep>; + }; + }; + + port@8 { + reg = <0x8>; + + xbar_admaif8_ep: endpoint { + remote-endpoint = <&admaif8_ep>; + }; + }; + + port@9 { + reg = <0x9>; + + xbar_admaif9_ep: endpoint { + remote-endpoint = <&admaif9_ep>; + }; + }; + + port@a { + reg = <0xa>; + + xbar_admaif10_ep: endpoint { + remote-endpoint = <&admaif10_ep>; + }; + }; + + port@b { + reg = <0xb>; + + xbar_admaif11_ep: endpoint { + remote-endpoint = <&admaif11_ep>; + }; + }; + + port@c { + reg = <0xc>; + + xbar_admaif12_ep: endpoint { + remote-endpoint = <&admaif12_ep>; + }; + }; + + port@d { + reg = <0xd>; + + xbar_admaif13_ep: endpoint { + remote-endpoint = <&admaif13_ep>; + }; + }; + + port@e { + reg = <0xe>; + + xbar_admaif14_ep: endpoint { + remote-endpoint = <&admaif14_ep>; + }; + }; + + port@f { + reg = <0xf>; + + xbar_admaif15_ep: endpoint { + remote-endpoint = <&admaif15_ep>; + }; + }; + + port@10 { + reg = <0x10>; + + xbar_admaif16_ep: endpoint { + remote-endpoint = <&admaif16_ep>; + }; + }; + + port@11 { + reg = <0x11>; + + xbar_admaif17_ep: endpoint { + remote-endpoint = <&admaif17_ep>; + }; + }; + + port@12 { + reg = <0x12>; + + xbar_admaif18_ep: endpoint { + remote-endpoint = <&admaif18_ep>; + }; + }; + + port@13 { + reg = <0x13>; + + xbar_admaif19_ep: endpoint { + remote-endpoint = <&admaif19_ep>; + }; + }; + + xbar_i2s1_port: port@14 { + reg = <0x14>; + + xbar_i2s1_ep: endpoint { + remote-endpoint = <&i2s1_cif_ep>; + }; + }; + + xbar_i2s2_port: port@15 { + reg = <0x15>; + + xbar_i2s2_ep: endpoint { + remote-endpoint = <&i2s2_cif_ep>; + }; + }; + + xbar_i2s3_port: port@16 { + reg = <0x16>; + + xbar_i2s3_ep: endpoint { + remote-endpoint = <&i2s3_cif_ep>; + }; + }; + + xbar_i2s4_port: port@17 { + reg = <0x17>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_i2s5_port: port@18 { + reg = <0x18>; + + xbar_i2s5_ep: endpoint { + remote-endpoint = <&i2s5_cif_ep>; + }; + }; + + xbar_i2s6_port: port@19 { + reg = <0x19>; + + xbar_i2s6_ep: endpoint { + remote-endpoint = <&i2s6_cif_ep>; + }; + }; + + xbar_dmic1_port: port@1a { + reg = <0x1a>; + + xbar_dmic1_ep: endpoint { + remote-endpoint = <&dmic1_cif_ep>; + }; + }; + + xbar_dmic2_port: port@1b { + reg = <0x1b>; + + xbar_dmic2_ep: endpoint { + remote-endpoint = <&dmic2_cif_ep>; + }; + }; + + xbar_dmic3_port: port@1c { + reg = <0x1c>; + + xbar_dmic3_ep: endpoint { + remote-endpoint = <&dmic3_cif_ep>; + }; + }; + + xbar_dspk1_port: port@1e { + reg = <0x1e>; + + xbar_dspk1_ep: endpoint { + remote-endpoint = <&dspk1_cif_ep>; + }; + }; + + xbar_dspk2_port: port@1f { + reg = <0x1f>; + + xbar_dspk2_ep: endpoint { + remote-endpoint = <&dspk2_cif_ep>; + }; + }; + }; + + admaif@290f000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + admaif0_port: port@0 { + reg = <0x0>; + + admaif0_ep: endpoint { + remote-endpoint = <&xbar_admaif0_ep>; + }; + }; + + admaif1_port: port@1 { + reg = <0x1>; + + admaif1_ep: endpoint { + remote-endpoint = <&xbar_admaif1_ep>; + }; + }; + + admaif2_port: port@2 { + reg = <0x2>; + + admaif2_ep: endpoint { + remote-endpoint = <&xbar_admaif2_ep>; + }; + }; + + admaif3_port: port@3 { + reg = <0x3>; + + admaif3_ep: endpoint { + remote-endpoint = <&xbar_admaif3_ep>; + }; + }; + + admaif4_port: port@4 { + reg = <0x4>; + + admaif4_ep: endpoint { + remote-endpoint = <&xbar_admaif4_ep>; + }; + }; + + admaif5_port: port@5 { + reg = <0x5>; + + admaif5_ep: endpoint { + remote-endpoint = <&xbar_admaif5_ep>; + }; + }; + + admaif6_port: port@6 { + reg = <0x6>; + + admaif6_ep: endpoint { + remote-endpoint = <&xbar_admaif6_ep>; + }; + }; + + admaif7_port: port@7 { + reg = <0x7>; + + admaif7_ep: endpoint { + remote-endpoint = <&xbar_admaif7_ep>; + }; + }; + + admaif8_port: port@8 { + reg = <0x8>; + + admaif8_ep: endpoint { + remote-endpoint = <&xbar_admaif8_ep>; + }; + }; + + admaif9_port: port@9 { + reg = <0x9>; + + admaif9_ep: endpoint { + remote-endpoint = <&xbar_admaif9_ep>; + }; + }; + + admaif10_port: port@a { + reg = <0xa>; + + admaif10_ep: endpoint { + remote-endpoint = <&xbar_admaif10_ep>; + }; + }; + + admaif11_port: port@b { + reg = <0xb>; + + admaif11_ep: endpoint { + remote-endpoint = <&xbar_admaif11_ep>; + }; + }; + + admaif12_port: port@c { + reg = <0xc>; + + admaif12_ep: endpoint { + remote-endpoint = <&xbar_admaif12_ep>; + }; + }; + + admaif13_port: port@d { + reg = <0xd>; + + admaif13_ep: endpoint { + remote-endpoint = <&xbar_admaif13_ep>; + }; + }; + + admaif14_port: port@e { + reg = <0xe>; + + admaif14_ep: endpoint { + remote-endpoint = <&xbar_admaif14_ep>; + }; + }; + + admaif15_port: port@f { + reg = <0xf>; + + admaif15_ep: endpoint { + remote-endpoint = <&xbar_admaif15_ep>; + }; + }; + + admaif16_port: port@10 { + reg = <0x10>; + + admaif16_ep: endpoint { + remote-endpoint = <&xbar_admaif16_ep>; + }; + }; + + admaif17_port: port@11 { + reg = <0x11>; + + admaif17_ep: endpoint { + remote-endpoint = <&xbar_admaif17_ep>; + }; + }; + + admaif18_port: port@12 { + reg = <0x12>; + + admaif18_ep: endpoint { + remote-endpoint = <&xbar_admaif18_ep>; + }; + }; + + admaif19_port: port@13 { + reg = <0x13>; + + admaif19_ep: endpoint { + remote-endpoint = <&xbar_admaif19_ep>; + }; + }; + }; + }; + + i2s@2901000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s1_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s1_ep>; + }; + }; + + i2s1_port: port@1 { + reg = <1>; + + i2s1_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s2_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s2_ep>; + }; + }; + + i2s2_port: port@1 { + reg = <1>; + + i2s2_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s3_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s3_ep>; + }; + }; + + i2s3_port: port@1 { + reg = <1>; + + i2s3_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901400 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s5_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s5_ep>; + }; + }; + + i2s5_port: port@1 { + reg = <1>; + + i2s5_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + i2s@2901500 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s6_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s6_ep>; + }; + }; + + i2s6_port: port@1 { + reg = <1>; + + i2s6_dap_ep: endpoint { + dai-format = "i2s"; + /* Placeholder for external Codec */ + }; + }; + }; + }; + + dmic@2904000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic1_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic1_ep>; + }; + }; + + dmic1_port: port@1 { + reg = <1>; + + dmic1_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dmic@2904100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic2_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic2_ep>; + }; + }; + + dmic2_port: port@1 { + reg = <1>; + + dmic2_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dmic@2904200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic3_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic3_ep>; + }; + }; + + dmic3_port: port@1 { + reg = <1>; + + dmic3_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dspk@2905000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dspk1_cif_ep: endpoint { + remote-endpoint = <&xbar_dspk1_ep>; + }; + }; + + dspk1_port: port@1 { + reg = <1>; + + dspk1_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + + dspk@2905100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dspk2_cif_ep: endpoint { + remote-endpoint = <&xbar_dspk2_ep>; + }; + }; + + dspk2_port: port@1 { + reg = <1>; + + dspk2_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + }; }; i2c@3160000 { @@ -381,4 +1088,27 @@ vin-supply = <&vdd_5v0_sys>; }; + + sound { + compatible = "nvidia,tegra186-audio-graph-card"; + status = "okay"; + + dais = /* FE */ + <&admaif0_port>, <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, <&admaif7_port>, + <&admaif8_port>, <&admaif9_port>, <&admaif10_port>, <&admaif11_port>, + <&admaif12_port>, <&admaif13_port>, <&admaif14_port>, <&admaif15_port>, + <&admaif16_port>, <&admaif17_port>, <&admaif18_port>, <&admaif19_port>, + /* Router */ + <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s3_port>, + <&xbar_i2s4_port>, <&xbar_i2s5_port>, <&xbar_i2s6_port>, + <&xbar_dmic1_port>, <&xbar_dmic2_port>, <&xbar_dmic3_port>, + <&xbar_dspk1_port>, <&xbar_dspk2_port>, + /* I/O */ + <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>, + <&i2s5_port>, <&i2s6_port>, <&dmic1_port>, <&dmic2_port>, + <&dmic3_port>, <&dspk1_port>, <&dspk2_port>; + + label = "jetson-tx2-ape"; + }; }; diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi index 58c51965df47..02b26b39cedc 100644 --- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi @@ -1678,6 +1678,28 @@ interrupt-affinity = <&ca57_0 &ca57_1 &ca57_2 &ca57_3>; }; + sound { + status = "disabled"; + + clocks = <&bpmp TEGRA186_CLK_PLLA>, + <&bpmp TEGRA186_CLK_PLL_A_OUT0>; + clock-names = "pll_a", "plla_out0"; + assigned-clocks = <&bpmp TEGRA186_CLK_PLLA>, + <&bpmp TEGRA186_CLK_PLL_A_OUT0>, + <&bpmp TEGRA186_CLK_AUD_MCLK>; + assigned-clock-parents = <0>, + <&bpmp TEGRA186_CLK_PLLA>, + <&bpmp TEGRA186_CLK_PLL_A_OUT0>; + /* + * PLLA supports dynamic ramp. Below initial rate is chosen + * for this to work and oscillate between base rates required + * for 8x and 11.025x sample rate streams. + */ + assigned-clock-rates = <258000000>; + + iommus = <&smmu TEGRA186_SID_APE>; + }; + thermal-zones { a57 { polling-delay = <0>; From 5b4f6323096a05870e557d841b209bf39e719440 Mon Sep 17 00:00:00 2001 From: Sameer Pujar Date: Fri, 29 Jan 2021 17:11:10 +0530 Subject: [PATCH 426/584] arm64: tegra: Audio graph sound card for Jetson AGX Xavier Enable support for audio-graph based sound card on Jetson AGX Xavier. Following I/O interfaces are enabled. * I2S1, I2S2, I2S4 and I2S6 * DMIC3 Signed-off-by: Sameer Pujar Signed-off-by: Thierry Reding --- .../boot/dts/nvidia/tegra194-p2972-0000.dts | 556 ++++++++++++++++++ arch/arm64/boot/dts/nvidia/tegra194.dtsi | 20 + 2 files changed, 576 insertions(+) diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts index f77f87c33e74..2888efc42ba1 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts +++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts @@ -21,6 +21,513 @@ interrupt-controller@2a40000 { status = "okay"; }; + + ahub@2900800 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0x0>; + + xbar_admaif0_ep: endpoint { + remote-endpoint = <&admaif0_ep>; + }; + }; + + port@1 { + reg = <0x1>; + + xbar_admaif1_ep: endpoint { + remote-endpoint = <&admaif1_ep>; + }; + }; + + port@2 { + reg = <0x2>; + + xbar_admaif2_ep: endpoint { + remote-endpoint = <&admaif2_ep>; + }; + }; + + port@3 { + reg = <0x3>; + + xbar_admaif3_ep: endpoint { + remote-endpoint = <&admaif3_ep>; + }; + }; + + port@4 { + reg = <0x4>; + + xbar_admaif4_ep: endpoint { + remote-endpoint = <&admaif4_ep>; + }; + }; + + port@5 { + reg = <0x5>; + + xbar_admaif5_ep: endpoint { + remote-endpoint = <&admaif5_ep>; + }; + }; + + port@6 { + reg = <0x6>; + + xbar_admaif6_ep: endpoint { + remote-endpoint = <&admaif6_ep>; + }; + }; + + port@7 { + reg = <0x7>; + + xbar_admaif7_ep: endpoint { + remote-endpoint = <&admaif7_ep>; + }; + }; + + port@8 { + reg = <0x8>; + + xbar_admaif8_ep: endpoint { + remote-endpoint = <&admaif8_ep>; + }; + }; + + port@9 { + reg = <0x9>; + + xbar_admaif9_ep: endpoint { + remote-endpoint = <&admaif9_ep>; + }; + }; + + port@a { + reg = <0xa>; + + xbar_admaif10_ep: endpoint { + remote-endpoint = <&admaif10_ep>; + }; + }; + + port@b { + reg = <0xb>; + + xbar_admaif11_ep: endpoint { + remote-endpoint = <&admaif11_ep>; + }; + }; + + port@c { + reg = <0xc>; + + xbar_admaif12_ep: endpoint { + remote-endpoint = <&admaif12_ep>; + }; + }; + + port@d { + reg = <0xd>; + + xbar_admaif13_ep: endpoint { + remote-endpoint = <&admaif13_ep>; + }; + }; + + port@e { + reg = <0xe>; + + xbar_admaif14_ep: endpoint { + remote-endpoint = <&admaif14_ep>; + }; + }; + + port@f { + reg = <0xf>; + + xbar_admaif15_ep: endpoint { + remote-endpoint = <&admaif15_ep>; + }; + }; + + port@10 { + reg = <0x10>; + + xbar_admaif16_ep: endpoint { + remote-endpoint = <&admaif16_ep>; + }; + }; + + port@11 { + reg = <0x11>; + + xbar_admaif17_ep: endpoint { + remote-endpoint = <&admaif17_ep>; + }; + }; + + port@12 { + reg = <0x12>; + + xbar_admaif18_ep: endpoint { + remote-endpoint = <&admaif18_ep>; + }; + }; + + port@13 { + reg = <0x13>; + + xbar_admaif19_ep: endpoint { + remote-endpoint = <&admaif19_ep>; + }; + }; + + xbar_i2s1_port: port@14 { + reg = <0x14>; + + xbar_i2s1_ep: endpoint { + remote-endpoint = <&i2s1_cif_ep>; + }; + }; + + xbar_i2s2_port: port@15 { + reg = <0x15>; + + xbar_i2s2_ep: endpoint { + remote-endpoint = <&i2s2_cif_ep>; + }; + }; + + xbar_i2s4_port: port@17 { + reg = <0x17>; + + xbar_i2s4_ep: endpoint { + remote-endpoint = <&i2s4_cif_ep>; + }; + }; + + xbar_i2s6_port: port@19 { + reg = <0x19>; + + xbar_i2s6_ep: endpoint { + remote-endpoint = <&i2s6_cif_ep>; + }; + }; + + xbar_dmic3_port: port@1c { + reg = <0x1c>; + + xbar_dmic3_ep: endpoint { + remote-endpoint = <&dmic3_cif_ep>; + }; + }; + }; + + admaif@290f000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + admaif0_port: port@0 { + reg = <0x0>; + + admaif0_ep: endpoint { + remote-endpoint = <&xbar_admaif0_ep>; + }; + }; + + admaif1_port: port@1 { + reg = <0x1>; + + admaif1_ep: endpoint { + remote-endpoint = <&xbar_admaif1_ep>; + }; + }; + + admaif2_port: port@2 { + reg = <0x2>; + + admaif2_ep: endpoint { + remote-endpoint = <&xbar_admaif2_ep>; + }; + }; + + admaif3_port: port@3 { + reg = <0x3>; + + admaif3_ep: endpoint { + remote-endpoint = <&xbar_admaif3_ep>; + }; + }; + + admaif4_port: port@4 { + reg = <0x4>; + + admaif4_ep: endpoint { + remote-endpoint = <&xbar_admaif4_ep>; + }; + }; + + admaif5_port: port@5 { + reg = <0x5>; + + admaif5_ep: endpoint { + remote-endpoint = <&xbar_admaif5_ep>; + }; + }; + + admaif6_port: port@6 { + reg = <0x6>; + + admaif6_ep: endpoint { + remote-endpoint = <&xbar_admaif6_ep>; + }; + }; + + admaif7_port: port@7 { + reg = <0x7>; + + admaif7_ep: endpoint { + remote-endpoint = <&xbar_admaif7_ep>; + }; + }; + + admaif8_port: port@8 { + reg = <0x8>; + + admaif8_ep: endpoint { + remote-endpoint = <&xbar_admaif8_ep>; + }; + }; + + admaif9_port: port@9 { + reg = <0x9>; + + admaif9_ep: endpoint { + remote-endpoint = <&xbar_admaif9_ep>; + }; + }; + + admaif10_port: port@a { + reg = <0xa>; + + admaif10_ep: endpoint { + remote-endpoint = <&xbar_admaif10_ep>; + }; + }; + + admaif11_port: port@b { + reg = <0xb>; + + admaif11_ep: endpoint { + remote-endpoint = <&xbar_admaif11_ep>; + }; + }; + + admaif12_port: port@c { + reg = <0xc>; + + admaif12_ep: endpoint { + remote-endpoint = <&xbar_admaif12_ep>; + }; + }; + + admaif13_port: port@d { + reg = <0xd>; + + admaif13_ep: endpoint { + remote-endpoint = <&xbar_admaif13_ep>; + }; + }; + + admaif14_port: port@e { + reg = <0xe>; + + admaif14_ep: endpoint { + remote-endpoint = <&xbar_admaif14_ep>; + }; + }; + + admaif15_port: port@f { + reg = <0xf>; + + admaif15_ep: endpoint { + remote-endpoint = <&xbar_admaif15_ep>; + }; + }; + + admaif16_port: port@10 { + reg = <0x10>; + + admaif16_ep: endpoint { + remote-endpoint = <&xbar_admaif16_ep>; + }; + }; + + admaif17_port: port@11 { + reg = <0x11>; + + admaif17_ep: endpoint { + remote-endpoint = <&xbar_admaif17_ep>; + }; + }; + + admaif18_port: port@12 { + reg = <0x12>; + + admaif18_ep: endpoint { + remote-endpoint = <&xbar_admaif18_ep>; + }; + }; + + admaif19_port: port@13 { + reg = <0x13>; + + admaif19_ep: endpoint { + remote-endpoint = <&xbar_admaif19_ep>; + }; + }; + }; + }; + + i2s@2901000 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s1_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s1_ep>; + }; + }; + + i2s1_port: port@1 { + reg = <1>; + + i2s1_dap_ep: endpoint { + dai-format = "i2s"; + remote-endpoint = <&rt5658_ep>; + }; + }; + }; + }; + + i2s@2901100 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s2_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s2_ep>; + }; + }; + + i2s2_port: port@1 { + reg = <1>; + + i2s2_dap_ep: endpoint { + dai-format = "i2s"; + /* Place holder for external Codec */ + }; + }; + }; + }; + + i2s@2901300 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s4_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s4_ep>; + }; + }; + + i2s4_port: port@1 { + reg = <1>; + + i2s4_dap_ep: endpoint { + dai-format = "i2s"; + /* Place holder for external Codec */ + }; + }; + }; + }; + + i2s@2901500 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + i2s6_cif_ep: endpoint { + remote-endpoint = <&xbar_i2s6_ep>; + }; + }; + + i2s6_port: port@1 { + reg = <1>; + + i2s6_dap_ep: endpoint@0 { + dai-format = "i2s"; + /* Place holder for external Codec */ + }; + }; + }; + }; + + dmic@2904200 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + dmic3_cif_ep: endpoint { + remote-endpoint = <&xbar_dmic3_ep>; + }; + }; + + dmic3_port: port@1 { + reg = <1>; + + dmic3_dap_ep: endpoint { + /* Place holder for external Codec */ + }; + }; + }; + }; + }; }; i2c@3160000 { @@ -146,6 +653,14 @@ interrupts = ; realtek,jd-src = <2>; sound-name-prefix = "CVB-RT"; + + port { + rt5658_ep: endpoint { + remote-endpoint = <&i2s1_dap_ep>; + mclk-fs = <256>; + clocks = <&bpmp TEGRA194_CLK_AUD_MCLK>; + }; + }; }; }; @@ -298,6 +813,47 @@ }; }; + sound { + compatible = "nvidia,tegra186-audio-graph-card"; + status = "okay"; + + dais = /* ADMAIF (FE) Ports */ + <&admaif0_port>, <&admaif1_port>, <&admaif2_port>, <&admaif3_port>, + <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, <&admaif7_port>, + <&admaif8_port>, <&admaif9_port>, <&admaif10_port>, <&admaif11_port>, + <&admaif12_port>, <&admaif13_port>, <&admaif14_port>, <&admaif15_port>, + <&admaif16_port>, <&admaif17_port>, <&admaif18_port>, <&admaif19_port>, + /* XBAR Ports */ + <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s4_port>, + <&xbar_i2s6_port>, <&xbar_dmic3_port>, + /* BE I/O Ports */ + <&i2s1_port>, <&i2s2_port>, <&i2s4_port>, <&i2s6_port>, + <&dmic3_port>; + + label = "jetson-xavier-ape"; + + widgets = + "Microphone", "CVB-RT MIC Jack", + "Microphone", "CVB-RT MIC", + "Headphone", "CVB-RT HP Jack", + "Speaker", "CVB-RT SPK"; + + routing = + /* I2S1 <-> RT5658 */ + "CVB-RT AIF1 Playback", "I2S1 DAP-Playback", + "I2S1 DAP-Capture", "CVB-RT AIF1 Capture", + /* RT5658 Codec controls */ + "CVB-RT HP Jack", "CVB-RT HPO L Playback", + "CVB-RT HP Jack", "CVB-RT HPO R Playback", + "CVB-RT IN1P", "CVB-RT MIC Jack", + "CVB-RT IN2P", "CVB-RT MIC Jack", + "CVB-RT SPK", "CVB-RT SPO Playback", + "CVB-RT DMIC L1", "CVB-RT MIC", + "CVB-RT DMIC L2", "CVB-RT MIC", + "CVB-RT DMIC R1", "CVB-RT MIC", + "CVB-RT DMIC R2", "CVB-RT MIC"; + }; + thermal-zones { cpu { polling-delay = <0>; diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi index 852980fe0d35..9449156fae39 100644 --- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi +++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi @@ -2351,6 +2351,26 @@ method = "smc"; }; + sound { + status = "disabled"; + + clocks = <&bpmp TEGRA194_CLK_PLLA>, + <&bpmp TEGRA194_CLK_PLLA_OUT0>; + clock-names = "pll_a", "plla_out0"; + assigned-clocks = <&bpmp TEGRA194_CLK_PLLA>, + <&bpmp TEGRA194_CLK_PLLA_OUT0>, + <&bpmp TEGRA194_CLK_AUD_MCLK>; + assigned-clock-parents = <0>, + <&bpmp TEGRA194_CLK_PLLA>, + <&bpmp TEGRA194_CLK_PLLA_OUT0>; + /* + * PLLA supports dynamic ramp. Below initial rate is chosen + * for this to work and oscillate between base rates required + * for 8x and 11.025x sample rate streams. + */ + assigned-clock-rates = <258000000>; + }; + tcu: tcu { compatible = "nvidia,tegra194-tcu"; mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM TEGRA_HSP_SM_RX(0)>, From 930a0968c6671d5d5cd7a1da569529ee1698b00a Mon Sep 17 00:00:00 2001 From: Kuldeep Singh Date: Thu, 21 Jan 2021 16:27:37 +0530 Subject: [PATCH 427/584] arm64: dts: lx2160a: Add flexcan support LX2160A supports two flexcan controllers. Add the support. Enable support further for LX2160A-RDB/QDS. Signed-off-by: Kuldeep Singh Signed-off-by: Shawn Guo --- .../boot/dts/freescale/fsl-lx2160a-qds.dts | 8 +++++++ .../boot/dts/freescale/fsl-lx2160a-rdb.dts | 16 +++++++++++++ .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 24 +++++++++++++++++++ 3 files changed, 48 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts index 16ae3b00cf48..d858d9c8b583 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts @@ -33,6 +33,14 @@ }; }; +&can0 { + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + &crypto { status = "okay"; }; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts index 6f82759f0ce4..5dbf27493e8b 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts @@ -89,6 +89,22 @@ }; }; +&can0 { + status = "okay"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; + +&can1 { + status = "okay"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; + &esdhc0 { sd-uhs-sdr104; sd-uhs-sdr50; diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi index 451e4430024c..0551f6f4c313 100644 --- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi @@ -895,6 +895,30 @@ status = "disabled"; }; + can0: can@2180000 { + compatible = "fsl,lx2160ar1-flexcan"; + reg = <0x0 0x2180000 0x0 0x10000>; + interrupts = ; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>, + <&clockgen QORIQ_CLK_SYSCLK 0>; + clock-names = "ipg", "per"; + fsl,clk-source = <0>; + status = "disabled"; + }; + + can1: can@2190000 { + compatible = "fsl,lx2160ar1-flexcan"; + reg = <0x0 0x2190000 0x0 0x10000>; + interrupts = ; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(8)>, + <&clockgen QORIQ_CLK_SYSCLK 0>; + clock-names = "ipg", "per"; + fsl,clk-source = <0>; + status = "disabled"; + }; + uart0: serial@21c0000 { compatible = "arm,sbsa-uart","arm,pl011"; reg = <0x0 0x21c0000 0x0 0x1000>; From c9e5ef8cef813f7a83f0e0060ed4ed3eadde183f Mon Sep 17 00:00:00 2001 From: Kuldeep Singh Date: Thu, 21 Jan 2021 16:27:38 +0530 Subject: [PATCH 428/584] arm64: dts: ls1028a: Update flexcan properties LS1028A supports two flexcan controllers similar to LX2160A. There's already a compatible entry defined i.e "fsl,lx2160ar1-flexcan" which can be further reused for LS1028A. Please note, "fsl,ls1028ar1-flexcan" compatible entry doesn't exists and can be safely removed. LS1028A has a single peripheral clock (i.e platform clock) source connected to both "ipg" and "per" and therefore, remove "sysclk" as clock source from device-tree. Signed-off-by: Kuldeep Singh Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 16 ++++++++++------ 1 file changed, 10 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi index 045739dbcb17..15143627ac8c 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi @@ -418,21 +418,25 @@ }; can0: can@2180000 { - compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; + compatible = "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = ; - clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL - QORIQ_CLK_PLL_DIV(2)>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; }; can1: can@2190000 { - compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; + compatible = "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = ; - clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL - QORIQ_CLK_PLL_DIV(2)>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; }; From 837ae08d95f2fe1ba33aa33b0256648b717e87b1 Mon Sep 17 00:00:00 2001 From: Kuldeep Singh Date: Thu, 21 Jan 2021 16:27:39 +0530 Subject: [PATCH 429/584] arm64: dts: ls1028a: Enable flexcan support for LS1028A-RDB/QDS LS1028A-RDB/QDS provides support for flexcan. Add the properties. Signed-off-by: Kuldeep Singh Signed-off-by: Shawn Guo --- .../arm64/boot/dts/freescale/fsl-ls1028a-qds.dts | 8 ++++++++ .../arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts | 16 ++++++++++++++++ 2 files changed, 24 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts index c0786b713791..fbcba9cb8503 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts @@ -109,6 +109,14 @@ }; }; +&can0 { + status = "okay"; +}; + +&can1 { + status = "okay"; +}; + &dspi0 { bus-num = <0>; status = "okay"; diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts index c1d1ba459307..41ae6e7675ba 100644 --- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts +++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts @@ -85,6 +85,22 @@ }; }; +&can0 { + status = "okay"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; + +&can1 { + status = "okay"; + + can-transceiver { + max-bitrate = <5000000>; + }; +}; + &esdhc { sd-uhs-sdr104; sd-uhs-sdr50; From 45a63cb55973631d3a60b0b0413ba88113e37dcd Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Mon, 25 Jan 2021 19:47:27 +0100 Subject: [PATCH 430/584] ARM: dts: imx6: rdu2: enable WDOG1 Enable the i.MX6 WDOG1 internal watchdog for warm reboots. This allows to issue emergency restarts without clearing the RAM, so collecting oops logs from ramoops pstore in barebox becomes feasible. Signed-off-by: Philipp Zabel Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 4 ---- 1 file changed, 4 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi index c0a76202e16b..04a66339ceb3 100644 --- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi @@ -885,10 +885,6 @@ }; }; -&wdog1 { - status = "disabled"; -}; - &iomuxc { pinctrl_accel: accelgrp { fsl,pins = < From a0c01b68fd3c8894194d440e4c8c61eefb3e5a68 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:28 +0100 Subject: [PATCH 431/584] ARM: dts: imx6: RDU2: reduce i2c drive-strength The current 25 Ohm drive-strength is much too strong, resulting in significant overshoot of the signal. Reduce the drive-strength to 75 Ohm to get rid of those issues. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi index 04a66339ceb3..56323890430e 100644 --- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi @@ -984,22 +984,22 @@ pinctrl_i2c1: i2c1grp { fsl,pins = < - MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1 - MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b811 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b811 >; }; pinctrl_i2c2: i2c2grp { fsl,pins = < - MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 - MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b811 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b811 >; }; pinctrl_i2c3: i2c3grp { fsl,pins = < - MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 - MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b811 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b811 >; }; From 20fffe76b6241d691a92f8d2fc0092da707dde67 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:29 +0100 Subject: [PATCH 432/584] ARM: dts: imx6: RDU2: enable RMI4 reduced reporting To use the reduced reporting mode the threshold values need to be set explicitly. Configure the threshold to be less than 0.5% of the full touchscreen range. This seems to be a good compromise between system load and input accurancy. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi index 56323890430e..ba26e1b8c474 100644 --- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi @@ -598,6 +598,8 @@ touchscreen-inverted-x; touchscreen-swapped-x-y; syna,sensor-type = <1>; + syna,delta-x-threshold = <5>; + syna,delta-y-threshold = <10>; }; rmi4-f12@12 { From 07aa5cf3af823ab2e7ce90cf147845363a35675c Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:30 +0100 Subject: [PATCH 433/584] ARM: dts: imx6: RDU2: only trigger IRQ on falling edge ucs1002 ALERT pin The ALERT signaling happens on the falling edge of the signal, as rising edge doesn't really have any notion, as it may happen much later (due to shared IRQ line) or too early if the chip resolves the fault itself. So only trigger the IRQ on the edge we are actually interested in. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi index ba26e1b8c474..dcc97a84c88d 100644 --- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi @@ -628,7 +628,7 @@ pinctrl-0 = <&pinctrl_ucs1002_pins>; reg = <0x32>; interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>, - <&gpio3 21 IRQ_TYPE_EDGE_BOTH>; + <&gpio3 21 IRQ_TYPE_EDGE_FALLING>; interrupt-names = "a_det", "alert"; }; From 498f8aee6ec000392d918ecbcbeb1b5ee3132006 Mon Sep 17 00:00:00 2001 From: Cory Tusar Date: Mon, 25 Jan 2021 19:47:31 +0100 Subject: [PATCH 434/584] ARM: dts: imx6: RDU2: adjust audio devices nomenclature This adds a "HPA1" prefix to the amplifiers on both audio cards, this is done in order to get more consistency for userspace running on RDU2 and RDU3, where we have two amplifiers on a single card device in the "Zest" configuration. Also adjust the card names to the new standard expected by userspace. Signed-off-by: Cory Tusar [adjusted commit message] Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-) diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi index dcc97a84c88d..525ff62b47f5 100644 --- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi +++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi @@ -112,17 +112,17 @@ sound1 { compatible = "simple-audio-card"; - simple-audio-card,name = "Front"; + simple-audio-card,name = "front"; simple-audio-card,format = "i2s"; simple-audio-card,bitclock-master = <&sound1_codec>; simple-audio-card,frame-master = <&sound1_codec>; simple-audio-card,widgets = "Headphone", "Headphone Jack"; simple-audio-card,routing = - "Headphone Jack", "HPLEFT", - "Headphone Jack", "HPRIGHT", - "LEFTIN", "HPL", - "RIGHTIN", "HPR"; + "Headphone Jack", "HPA1 HPLEFT", + "Headphone Jack", "HPA1 HPRIGHT", + "HPA1 LEFTIN", "HPL", + "HPA1 RIGHTIN", "HPR"; simple-audio-card,aux-devs = <&hpa1>; sound1_cpu: simple-audio-card,cpu { @@ -137,17 +137,17 @@ sound2 { compatible = "simple-audio-card"; - simple-audio-card,name = "Back"; + simple-audio-card,name = "periph"; simple-audio-card,format = "i2s"; simple-audio-card,bitclock-master = <&sound2_codec>; simple-audio-card,frame-master = <&sound2_codec>; simple-audio-card,widgets = "Headphone", "Headphone Jack"; simple-audio-card,routing = - "Headphone Jack", "HPLEFT", - "Headphone Jack", "HPRIGHT", - "LEFTIN", "HPL", - "RIGHTIN", "HPR"; + "Headphone Jack", "HPA1 HPLEFT", + "Headphone Jack", "HPA1 HPRIGHT", + "HPA1 LEFTIN", "HPL", + "HPA1 RIGHTIN", "HPR"; simple-audio-card,aux-devs = <&hpa2>; sound2_cpu: simple-audio-card,cpu { @@ -399,6 +399,7 @@ reg = <0x60>; power-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>; Vdd-supply = <®_5p0v_main>; + sound-name-prefix = "HPA1"; }; edp-bridge@68 { @@ -639,6 +640,7 @@ reg = <0x60>; power-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>; Vdd-supply = <®_5p0v_main>; + sound-name-prefix = "HPA1"; }; }; From 663a5b5efa510b91fa35a0a08eae9ec6a364ebcb Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:32 +0100 Subject: [PATCH 435/584] arm64: dts: zii-ultra: add sound support This adds all the necessary nodes to get audio support on both the RMB3 and Zest boards. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- .../dts/freescale/imx8mq-zii-ultra-rmb3.dts | 91 +++++++++++++++++ .../dts/freescale/imx8mq-zii-ultra-zest.dts | 30 ++++++ .../boot/dts/freescale/imx8mq-zii-ultra.dtsi | 98 +++++++++++++++++++ 3 files changed, 219 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts index bfad4b885905..b3743f96f899 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts @@ -10,6 +10,56 @@ / { model = "ZII Ultra RMB3 Board"; compatible = "zii,imx8mq-ultra-rmb3", "zii,imx8mq-ultra", "fsl,imx8mq"; + + sound1 { + compatible = "simple-audio-card"; + simple-audio-card,name = "front"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound1_codec>; + simple-audio-card,frame-master = <&sound1_codec>; + simple-audio-card,widgets = + "Headphone", "Headphone Jack Front"; + simple-audio-card,routing = + "Headphone Jack Front", "HPA1 HPLEFT", + "Headphone Jack Front", "HPA1 HPRIGHT", + "HPA1 LEFTIN", "HPL", + "HPA1 RIGHTIN", "HPR"; + simple-audio-card,aux-devs = <&hpa1>; + + sound1_cpu: simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + + sound1_codec: simple-audio-card,codec { + sound-dai = <&codec1>; + clocks = <&cs2000>; + }; + }; + + sound2 { + compatible = "simple-audio-card"; + simple-audio-card,name = "periph"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound2_codec>; + simple-audio-card,frame-master = <&sound2_codec>; + simple-audio-card,widgets = + "Headphone", "Headphone Jack Back"; + simple-audio-card,routing = + "Headphone Jack Back", "HPA1 HPLEFT", + "Headphone Jack Back", "HPA1 HPRIGHT", + "HPA1 LEFTIN", "HPL", + "HPA1 RIGHTIN", "HPR"; + simple-audio-card,aux-devs = <&hpa2>; + + sound2_cpu: simple-audio-card,cpu { + sound-dai = <&sai3>; + }; + + sound2_codec: simple-audio-card,codec { + sound-dai = <&codec2>; + clocks = <&cs2000>; + }; + }; }; &ecspi1 { @@ -27,6 +77,27 @@ }; }; +&hpa2 { + sound-name-prefix = "HPA1"; +}; + +&i2c1 { + codec2: codec@18 { + compatible = "ti,tlv320dac3100"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_codec2>; + reg = <0x18>; + #sound-dai-cells = <0>; + HPVDD-supply = <®_3p3v>; + SPRVDD-supply = <®_3p3v>; + SPLVDD-supply = <®_3p3v>; + AVDD-supply = <®_3p3v>; + IOVDD-supply = <®_3p3v>; + DVDD-supply = <&vgen4_reg>; + reset-gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>; + }; +}; + &i2c2 { temp-sense@48 { compatible = "national,lm75"; @@ -79,11 +150,23 @@ }; }; +&sai3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai3>; + status = "okay"; +}; + &usbhub { swap-dx-lanes = <0>; }; &iomuxc { + pinctrl_codec2: dac2grp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x41 + >; + }; + pinctrl_ecspi1: ecspi1grp { fsl,pins = < MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9 0x19 @@ -92,4 +175,12 @@ MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI 0x82 >; }; + + pinctrl_sai3: sai3grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC 0xd6 + MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK 0xd6 + MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0 0xd6 + >; + }; }; diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-zest.dts b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-zest.dts index 173b9e9b2bbd..f6130167a1c7 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-zest.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-zest.dts @@ -10,6 +10,36 @@ / { model = "ZII Ultra Zest Board"; compatible = "zii,imx8mq-ultra-zest", "zii,imx8mq-ultra", "fsl,imx8mq"; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "front"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sound_codec>; + simple-audio-card,frame-master = <&sound_codec>; + simple-audio-card,widgets = + "Headphone", "Headphone Jack Front", + "Headphone", "Headphone Jack Back"; + simple-audio-card,routing = + "Headphone Jack Front", "HPA1 HPLEFT", + "Headphone Jack Front", "HPA1 HPRIGHT", + "Headphone Jack Back", "HPA2 HPLEFT", + "Headphone Jack Back", "HPA2 HPRIGHT", + "HPA1 LEFTIN", "HPL", + "HPA1 RIGHTIN", "HPR", + "HPA2 LEFTIN", "HPL", + "HPA2 RIGHTIN", "HPR"; + simple-audio-card,aux-devs = <&hpa1>, <&hpa2>; + + sound_cpu: simple-audio-card,cpu { + sound-dai = <&sai2>; + }; + + sound_codec: simple-audio-card,codec { + sound-dai = <&codec1>; + clocks = <&cs2000>; + }; + }; }; &i2c4 { diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi index fa7a041ffcfd..e6469e15bcbd 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi @@ -77,6 +77,15 @@ regulator-always-on; }; + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + vin-supply = <®_3p3_main>; + regulator-name = "GEN_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + reg_usdhc2_vmmc: regulator-vsd-3v3 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_reg_usdhc2>; @@ -102,6 +111,18 @@ 900000 0x0>; regulator-always-on; }; + + cs2000_ref: cs2000-ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24576000>; + }; + + cs2000_in_dummy: cs2000-in-dummy { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <0>; + }; }; &A53_0 { @@ -286,6 +307,16 @@ <18 IRQ_TYPE_EDGE_BOTH>; interrupt-names = "a_det", "alert"; }; + + hpa2: amp@60 { + compatible = "ti,tpa6130a2"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tpa2>; + reg = <0x60>; + power-gpio = <&gpio1 8 GPIO_ACTIVE_HIGH>; + Vdd-supply = <®_5p0_main>; + sound-name-prefix = "HPA2"; + }; }; &i2c2 { @@ -378,11 +409,36 @@ }; }; + codec1: codec@18 { + compatible = "ti,tlv320dac3100"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_codec1>; + reg = <0x18>; + #sound-dai-cells = <0>; + HPVDD-supply = <®_3p3v>; + SPRVDD-supply = <®_3p3v>; + SPLVDD-supply = <®_3p3v>; + AVDD-supply = <®_3p3v>; + IOVDD-supply = <®_3p3v>; + DVDD-supply = <&vgen4_reg>; + reset-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>; + }; + eeprom@54 { compatible = "atmel,24c128"; reg = <0x54>; }; + hpa1: amp@60 { + compatible = "ti,tpa6130a2"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tpa1>; + reg = <0x60>; + power-gpio = <&gpio4 10 GPIO_ACTIVE_HIGH>; + Vdd-supply = <®_5p0_main>; + sound-name-prefix = "HPA1"; + }; + ds1341: rtc@68 { compatible = "dallas,ds1341"; reg = <0x68>; @@ -407,6 +463,16 @@ compatible = "zii,rave-wdt"; reg = <0x38>; }; + + cs2000: clkgen@4e { + compatible = "cirrus,cs2000-cp"; + reg = <0x4e>; + #clock-cells = <0>; + clock-names = "clk_in", "ref_clk"; + clocks = <&cs2000_in_dummy>, <&cs2000_ref>; + assigned-clocks = <&cs2000>; + assigned-clock-rates = <24000000>; + }; }; &i2c4 { @@ -416,6 +482,12 @@ status = "okay"; }; +&sai2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_uart1>; @@ -551,6 +623,12 @@ >; }; + pinctrl_codec1: dac1grp { + fsl,pins = < + MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3 0x41 + >; + }; + pinctrl_fec1: fec1grp { fsl,pins = < MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 @@ -642,12 +720,32 @@ >; }; + pinctrl_sai2: sai2grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC 0xd6 + MX8MQ_IOMUXC_SAI2_TXC_SAI2_TX_BCLK 0xd6 + MX8MQ_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0 0xd6 + >; + }; + pinctrl_switch_irq: switchgrp { fsl,pins = < MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x41 >; }; + pinctrl_tpa1: tpa6130-1grp { + fsl,pins = < + MX8MQ_IOMUXC_SAI1_TXFS_GPIO4_IO10 0x41 + >; + }; + + pinctrl_tpa2: tpa6130-2grp { + fsl,pins = < + MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x41 + >; + }; + pinctrl_ts: tsgrp { fsl,pins = < MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x96 From 71a8434857d51c1aa15b17338626b273f5e58be1 Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:33 +0100 Subject: [PATCH 436/584] arm64: dts: zii-ultra: fix i2c pin configuration Reduce slew rate and set drive strength to 105 Ohm. The previous settings had some issues with signal ringing, due to the slew rate being too fast. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- .../boot/dts/freescale/imx8mq-zii-ultra.dtsi | 16 ++++++++-------- 1 file changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi index e6469e15bcbd..aa05d5fd1b3b 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi @@ -661,29 +661,29 @@ pinctrl_i2c1: i2c1grp { fsl,pins = < - MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f - MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f + MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x40000022 + MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x400000a2 >; }; pinctrl_i2c2: i2c2grp { fsl,pins = < - MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f - MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f + MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x40000022 + MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x400000a2 >; }; pinctrl_i2c3: i2c3grp { fsl,pins = < - MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f - MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f + MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x40000022 + MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x400000a2 >; }; pinctrl_i2c4: i2c4grp { fsl,pins = < - MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x4000007f - MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x4000007f + MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL 0x40000022 + MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA 0x400000a2 >; }; From f2615e598a50f8077e6ec70e2060ca0b5d8f989f Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:34 +0100 Subject: [PATCH 437/584] arm64: dts: zii-ultra: limit USB ports to USB2 speed The internal USB is connected to a USB2 hub, the front-panel USB is wired directly, but does not support USB3 speeds electrically. Limit both ports accordingly. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi index aa05d5fd1b3b..edbde9ed4caf 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi @@ -540,6 +540,7 @@ &usb_dwc3_0 { dr_mode = "host"; + maximum-speed = "high-speed"; status = "okay"; }; @@ -550,6 +551,7 @@ &usb_dwc3_1 { dr_mode = "host"; + maximum-speed = "high-speed"; status = "okay"; }; From b53e7e0c65bfb68aee4fba83eb3b6ec74f0869ae Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:35 +0100 Subject: [PATCH 438/584] arm64: dts: zii-ultra: only trigger IRQ on falling edge ucs1002 ALERT pin The ALERT signaling happens on the falling edge of the signal, as rising edge doesn't really have any notion, as it may happen much later (due to shared IRQ line) or too early if the chip resolves the fault itself. So only trigger the IRQ on the edge we are actually interested in. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi index edbde9ed4caf..4dc8383478ee 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi @@ -304,7 +304,7 @@ reg = <0x32>; interrupt-parent = <&gpio3>; interrupts = <17 IRQ_TYPE_EDGE_BOTH>, - <18 IRQ_TYPE_EDGE_BOTH>; + <18 IRQ_TYPE_EDGE_FALLING>; interrupt-names = "a_det", "alert"; }; From 370d82d3facfb3709c3f4c793229f5b8f5c7001e Mon Sep 17 00:00:00 2001 From: Lucas Stach Date: Mon, 25 Jan 2021 19:47:36 +0100 Subject: [PATCH 439/584] arm64: dts: zii-rmb3: enable RMI4 reduced reporting To use the reduced reporting mode the threshold values need to be set explicitly. Configure the threshold to be less than 0.5% of the full touchscreen range. This seems to be a good compromise between system load and input accurancy. Signed-off-by: Lucas Stach Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts index b3743f96f899..631e01c1b9fd 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts +++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-rmb3.dts @@ -127,6 +127,8 @@ touchscreen-inverted-x; touchscreen-swapped-x-y; syna,sensor-type = <1>; + syna,delta-x-threshold = <5>; + syna,delta-y-threshold = <10>; }; rmi4-f12@12 { From 1447e43c0b735ffc0d48a6aec4f74d6877caffc2 Mon Sep 17 00:00:00 2001 From: Adrien Grassein Date: Thu, 28 Jan 2021 20:35:52 +0100 Subject: [PATCH 440/584] dt-bindings: arm: imx: add imx8mm nitrogen support The Nitrogen8M Mini is an ARM based single board computer (SBC). Signed-off-by: Adrien Grassein Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- Documentation/devicetree/bindings/arm/fsl.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 47220e2f522c..297c87f45db8 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -678,6 +678,7 @@ properties: items: - enum: - beacon,imx8mm-beacon-kit # i.MX8MM Beacon Development Kit + - boundary,imx8mm-nitrogen8mm # i.MX8MM Nitrogen Board - fsl,imx8mm-ddr4-evk # i.MX8MM DDR4 EVK Board - fsl,imx8mm-evk # i.MX8MM EVK Board - gw,imx8mm-gw71xx-0x # i.MX8MM Gateworks Development Kit From da1a6b8bec881b67f0e234ed19e8b7e2fb1e7812 Mon Sep 17 00:00:00 2001 From: Adrien Grassein Date: Thu, 28 Jan 2021 20:35:53 +0100 Subject: [PATCH 441/584] arm64: dts: imx: Add i.mx8mm nitrogen basic dts support Tested with a basic Build Root configuration booting from sdcard. Signed-off-by: Adrien Grassein Reviewed-by: Krzysztof Kozlowski Signed-off-by: Shawn Guo --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../boot/dts/freescale/imx8mm-nitrogen-r2.dts | 393 ++++++++++++++++++ 2 files changed, 394 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 44a20b89b1ef..6438db3822f8 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts new file mode 100644 index 000000000000..c0c384d76147 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen-r2.dts @@ -0,0 +1,393 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Device Tree file for Boundary Devices i.MX8MMini Nitrogen8MM Rev2 board. + * Adrien Grassein + */ +/dts-v1/; +#include "imx8mm.dtsi" + +/ { + model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2"; + compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm"; +}; + +&A53_0 { + cpu-supply = <®_buck3>; +}; + +&A53_1 { + cpu-supply = <®_buck3>; +}; + +&A53_2 { + cpu-supply = <®_buck3>; +}; + +&A53_3 { + cpu-supply = <®_buck3>; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + phy-mode = "rgmii-id"; + phy-handle = <ðphy0>; + fsl,magic-packet; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet-phy@4 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <4>; + interrupts-extended = <&gpio3 16 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@8 { + compatible = "nxp,pf8121a"; + reg = <0x8>; + + regulators { + reg_ldo1: ldo1 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_ldo2: ldo2 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_ldo3: ldo3 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_ldo4: ldo4 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck1: buck1 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck2: buck2 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck3: buck3 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck4: buck4 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck5: buck5 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck6: buck6 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_buck7: buck7 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vsnvs: vsnvs { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + i2cmux@70 { + compatible = "nxp,pca9540"; + reg = <0x70>; + #address-cells = <1>; + #size-cells = <0>; + + i2c3 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "microcrystal,rv4162"; + reg = <0x68>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3a_rv4162>; + interrupts-extended = <&gpio4 22 IRQ_TYPE_LEVEL_LOW>; + wakeup-source; + }; + }; + }; +}; + +/* console */ +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + assigned-clocks = <&clk IMX8MM_CLK_UART2>; + assigned-clock-parents = <&clk IMX8MM_CLK_24M>; + status = "okay"; +}; + +/* eMMC */ +&usdhc1 { + bus-width = <8>; + sdhci-caps-mask = <0x80000000 0x0>; + non-removable; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + status = "okay"; +}; + +/* sdcard */ +&usdhc2 { + bus-width = <4>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + vqmmc-supply = <®_ldo2>; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x159 + >; + }; + + pinctrl_hog: hoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x09 + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x09 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 + >; + }; + + pinctrl_i2c3a_rv4162: i2c3a-rv4162grp { + fsl,pins = < + MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140 + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0 + MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x141 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6 + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6 + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6 + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0 + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196 + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6 + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6 + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6 + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6 + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x03 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp { + fsl,pins = < + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x140 + >; + }; +}; From dbcd865bc7a8d06a844b6a607082b16251d42f70 Mon Sep 17 00:00:00 2001 From: Fabien Parent Date: Wed, 9 Dec 2020 12:47:36 +0100 Subject: [PATCH 442/584] arm64: dts: mediatek: mt8516: add support for APDMA Add support the APDMA IP on MT8516. APDMA is a DMA controller for UARTs. Signed-off-by: Fabien Parent Link: https://lore.kernel.org/r/20201209114736.70625-2-fparent@baylibre.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8516.dtsi | 30 ++++++++++++++++++++++++ 1 file changed, 30 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8516.dtsi b/arch/arm64/boot/dts/mediatek/mt8516.dtsi index e6e4d9d60094..b80e95574bef 100644 --- a/arch/arm64/boot/dts/mediatek/mt8516.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8516.dtsi @@ -276,6 +276,27 @@ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; + apdma: dma-controller@11000480 { + compatible = "mediatek,mt8516-uart-dma", + "mediatek,mt6577-uart-dma"; + reg = <0 0x11000480 0 0x80>, + <0 0x11000500 0 0x80>, + <0 0x11000580 0 0x80>, + <0 0x11000600 0 0x80>, + <0 0x11000980 0 0x80>, + <0 0x11000a00 0 0x80>; + interrupts = , + , + , + , + , + ; + dma-requests = <6>; + clocks = <&topckgen CLK_TOP_APDMA>; + clock-names = "apdma"; + #dma-cells = <1>; + }; + uart0: serial@11005000 { compatible = "mediatek,mt8516-uart", "mediatek,mt6577-uart"; @@ -284,6 +305,9 @@ clocks = <&topckgen CLK_TOP_UART0_SEL>, <&topckgen CLK_TOP_UART0>; clock-names = "baud", "bus"; + dmas = <&apdma 0 + &apdma 1>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -295,6 +319,9 @@ clocks = <&topckgen CLK_TOP_UART1_SEL>, <&topckgen CLK_TOP_UART1>; clock-names = "baud", "bus"; + dmas = <&apdma 2 + &apdma 3>; + dma-names = "tx", "rx"; status = "disabled"; }; @@ -306,6 +333,9 @@ clocks = <&topckgen CLK_TOP_UART2_SEL>, <&topckgen CLK_TOP_UART2>; clock-names = "baud", "bus"; + dmas = <&apdma 4 + &apdma 5>; + dma-names = "tx", "rx"; status = "disabled"; }; From d0a197a0d064abe579e21300a7ee74e8dc331112 Mon Sep 17 00:00:00 2001 From: bayi cheng Date: Wed, 23 Dec 2020 12:22:59 +0800 Subject: [PATCH 443/584] arm64: dts: mt8192: add nor_flash device node add nor_flash device node Signed-off-by: bayi cheng Link: https://lore.kernel.org/r/1608697379-22025-1-git-send-email-bayi.cheng@mediatek.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8192.dtsi | 13 +++++++++++++ 1 file changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8192.dtsi b/arch/arm64/boot/dts/mediatek/mt8192.dtsi index e12e024de122..751c877e082c 100644 --- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi @@ -379,6 +379,19 @@ status = "disabled"; }; + nor_flash: spi@11234000 { + compatible = "mediatek,mt8192-nor"; + reg = <0 0x11234000 0 0xe0>; + interrupts = ; + clocks = <&clk26m>, + <&clk26m>, + <&clk26m>; + clock-names = "spi", "sf", "axi"; + #address-cells = <1>; + #size-cells = <0>; + status = "disable"; + }; + i2c3: i2c3@11cb0000 { compatible = "mediatek,mt8192-i2c"; reg = <0 0x11cb0000 0 0x1000>, From 9e1b7d00bbe1128813dc5bb95cf84c60cea0bb74 Mon Sep 17 00:00:00 2001 From: Hsin-Yi Wang Date: Fri, 29 Jan 2021 18:12:08 +0800 Subject: [PATCH 444/584] arm64: dts: mediatek: mt8183: Add domain supply for mfg Add domain supply node. Signed-off-by: Hsin-Yi Wang Link: https://lore.kernel.org/r/20210129101208.2625249-4-hsinyi@chromium.org Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 4 ++++ arch/arm64/boot/dts/mediatek/mt8183.dtsi | 2 +- 2 files changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi index bf2ad1294dd3..ebd53755d538 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi @@ -709,6 +709,10 @@ }; }; +&mfg { + domain-supply = <&mt6358_vgpu_reg>; +}; + &soc_data { status = "okay"; }; diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index f4d0f5de99b9..b3b8afec5ab9 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -360,7 +360,7 @@ #size-cells = <0>; #power-domain-cells = <1>; - power-domain@MT8183_POWER_DOMAIN_MFG { + mfg: power-domain@MT8183_POWER_DOMAIN_MFG { reg = ; #address-cells = <1>; #size-cells = <0>; From 9260918d3a4fae5a30061b08ba7b858ecebdbb34 Mon Sep 17 00:00:00 2001 From: James Liao Date: Tue, 22 Dec 2020 12:58:20 +0800 Subject: [PATCH 445/584] arm64: dts: mt8192: Add cpu-idle-states Add idle states for cpu-off and cluster-off. Signed-off-by: James Liao Link: https://lore.kernel.org/r/20201222045820.26355-1-jamesjj.liao@mediatek.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8192.dtsi | 44 ++++++++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8192.dtsi b/arch/arm64/boot/dts/mediatek/mt8192.dtsi index 751c877e082c..9757138a8bbd 100644 --- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi @@ -39,6 +39,7 @@ reg = <0x000>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -49,6 +50,7 @@ reg = <0x100>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -59,6 +61,7 @@ reg = <0x200>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -69,6 +72,7 @@ reg = <0x300>; enable-method = "psci"; clock-frequency = <1701000000>; + cpu-idle-states = <&cpuoff_l &clusteroff_l>; next-level-cache = <&l2_0>; capacity-dmips-mhz = <530>; }; @@ -79,6 +83,7 @@ reg = <0x400>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -89,6 +94,7 @@ reg = <0x500>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -99,6 +105,7 @@ reg = <0x600>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -109,6 +116,7 @@ reg = <0x700>; enable-method = "psci"; clock-frequency = <2171000000>; + cpu-idle-states = <&cpuoff_b &clusteroff_b>; next-level-cache = <&l2_1>; capacity-dmips-mhz = <1024>; }; @@ -158,6 +166,42 @@ l3_0: l3-cache { compatible = "cache"; }; + + idle-states { + entry-method = "arm,psci"; + cpuoff_l: cpuoff_l { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x00010001>; + local-timer-stop; + entry-latency-us = <55>; + exit-latency-us = <140>; + min-residency-us = <780>; + }; + cpuoff_b: cpuoff_b { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x00010001>; + local-timer-stop; + entry-latency-us = <35>; + exit-latency-us = <145>; + min-residency-us = <720>; + }; + clusteroff_l: clusteroff_l { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x01010002>; + local-timer-stop; + entry-latency-us = <60>; + exit-latency-us = <155>; + min-residency-us = <860>; + }; + clusteroff_b: clusteroff_b { + compatible = "arm,idle-state"; + arm,psci-suspend-param = <0x01010002>; + local-timer-stop; + entry-latency-us = <40>; + exit-latency-us = <155>; + min-residency-us = <780>; + }; + }; }; pmu-a55 { From 3960a7a25b5d243691e11f6bc8d2d339d5dafa5a Mon Sep 17 00:00:00 2001 From: Neal Liu Date: Wed, 23 Dec 2020 16:44:51 +0800 Subject: [PATCH 446/584] arm64: dts: mt6779: Support devapc Support DEVAPC on MT6779 platforms by adding device node. Signed-off-by: Neal Liu Reviewed-by: Hanks Chen Link: https://lore.kernel.org/r/1608713092-26952-2-git-send-email-neal.liu@mediatek.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt6779.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt6779.dtsi b/arch/arm64/boot/dts/mediatek/mt6779.dtsi index 370f309d32de..52ecfc71a5f4 100644 --- a/arch/arm64/boot/dts/mediatek/mt6779.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt6779.dtsi @@ -189,6 +189,14 @@ #clock-cells = <1>; }; + devapc: devapc@10207000 { + compatible = "mediatek,mt6779-devapc"; + reg = <0 0x10207000 0 0x1000>; + interrupts = ; + clocks = <&infracfg_ao CLK_INFRA_DEVICE_APC>; + clock-names = "devapc-infra-clock"; + }; + uart0: serial@11002000 { compatible = "mediatek,mt6779-uart", "mediatek,mt6577-uart"; From b870c58582141130cc7067719546311255562e72 Mon Sep 17 00:00:00 2001 From: Argus Lin Date: Mon, 4 Jan 2021 16:08:22 +0800 Subject: [PATCH 447/584] arm64: dts: mt6779: Support pwrap on Mediatek MT6779 platform Support pwrap on Mediatek MT6779 platform by adding pwrap node in dts file. Signed-off-by: Argus Lin Link: https://lore.kernel.org/r/1609747703-27207-2-git-send-email-argus.lin@mediatek.com Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt6779.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt6779.dtsi b/arch/arm64/boot/dts/mediatek/mt6779.dtsi index 52ecfc71a5f4..9bdf5145966c 100644 --- a/arch/arm64/boot/dts/mediatek/mt6779.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt6779.dtsi @@ -189,6 +189,15 @@ #clock-cells = <1>; }; + pwrap: pwrap@1000d000 { + compatible = "mediatek,mt6779-pwrap"; + reg = <0 0x1000d000 0 0x1000>; + reg-names = "pwrap"; + interrupts = ; + clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_PMIC_AP>; + clock-names = "spi", "wrap"; + }; + devapc: devapc@10207000 { compatible = "mediatek,mt6779-devapc"; reg = <0 0x10207000 0 0x1000>; From 27eaf34df36419ead90801ef1ba73db287944158 Mon Sep 17 00:00:00 2001 From: Hsin-Yi Wang Date: Wed, 13 Jan 2021 19:03:59 +0800 Subject: [PATCH 448/584] arm64: dts: mt8183: config dsi node Config dsi node for mt8183 kukui. Set panel and ports. Several kukui boards share the same panel property and only compatible is different. So compatible will be set in board dts for comparison convenience. Signed-off-by: Hsin-Yi Wang Tested-by: Enric Balletbo i Serra Reviewed-by: Nicolas Boichat Link: https://lore.kernel.org/r/20210113110400.616319-1-hsinyi@chromium.org Signed-off-by: Matthias Brugger --- .../mediatek/mt8183-kukui-krane-sku176.dts | 5 +++ .../arm64/boot/dts/mediatek/mt8183-kukui.dtsi | 42 +++++++++++++++++++ 2 files changed, 47 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts index 47113e275cb5..721d16f9c3b4 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku176.dts @@ -16,3 +16,8 @@ model = "MediaTek krane sku176 board"; compatible = "google,krane-sku176", "google,krane", "mediatek,mt8183"; }; + +&panel { + status = "okay"; + compatible = "boe,tv101wum-nl6"; +}; diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi index ebd53755d538..ff56bcfa3370 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi @@ -249,6 +249,36 @@ proc-supply = <&mt6358_vproc11_reg>; }; +&dsi0 { + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + panel: panel@0 { + /* compatible will be set in board dts */ + reg = <0>; + enable-gpios = <&pio 45 0>; + pinctrl-names = "default"; + pinctrl-0 = <&panel_pins_default>; + avdd-supply = <&ppvarn_lcd>; + avee-supply = <&ppvarp_lcd>; + pp1800-supply = <&pp1800_lcd>; + backlight = <&backlight_lcd0>; + port { + panel_in: endpoint { + remote-endpoint = <&dsi_out>; + }; + }; + }; + + ports { + port { + dsi_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + &i2c0 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; @@ -290,6 +320,10 @@ clock-frequency = <100000>; }; +&mipi_tx0 { + status = "okay"; +}; + &mmc0 { status = "okay"; pinctrl-names = "default", "state_uhs"; @@ -547,6 +581,14 @@ }; }; + panel_pins_default: panel_pins_default { + panel_reset { + pinmux = ; + output-low; + bias-pull-up; + }; + }; + pwm0_pin_default: pwm0_pin_default { pins1 { pinmux = ; From 17cf7d4d940f4386e3b4d8e9db907887520d837a Mon Sep 17 00:00:00 2001 From: Hsin-Yi Wang Date: Wed, 13 Jan 2021 19:04:01 +0800 Subject: [PATCH 449/584] arm64: dts: mt8183: Add krane-sku0 board. Similar to krane-sku176 but using a different panel source. Signed-off-by: Hsin-Yi Wang Reviewed-by: Enric Balletbo i Serra Link: https://lore.kernel.org/r/20210113110400.616319-2-hsinyi@chromium.org Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/Makefile | 1 + .../dts/mediatek/mt8183-kukui-krane-sku0.dts | 23 +++++++++++++++++++ 2 files changed, 24 insertions(+) create mode 100644 arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index 18f7b46c4095..deba27ab7657 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -13,6 +13,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts new file mode 100644 index 000000000000..fb5ee91b6fe0 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-krane-sku0.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2019 Google LLC + * + * Device-tree for Krane sku0. + * + * SKU is a 8-bit value (0x00 == 0): + * - Bits 7..4: Panel ID: 0x0 (AUO) + * - Bits 3..0: SKU ID: 0x0 (default) + */ + +/dts-v1/; +#include "mt8183-kukui-krane.dtsi" + +/ { + model = "MediaTek krane sku0 board"; + compatible = "google,krane-sku0", "google,krane", "mediatek,mt8183"; +}; + +&panel { + status = "okay"; + compatible = "auo,kd101n80-45na"; +}; From f93b04efaf80fe3d8ea1776a71a9e8e7fb3cfeab Mon Sep 17 00:00:00 2001 From: Hsin-Yi Wang Date: Wed, 13 Jan 2021 19:04:03 +0800 Subject: [PATCH 450/584] dt-bindings: arm64: dts: mediatek: Add krane sku0 Krane-sku0 is similar to krane-sku176 but using a different panel source. Signed-off-by: Hsin-Yi Wang Reviewed-by: Rob Herring Reviewed-by: Enric Balletbo i Serra Link: https://lore.kernel.org/r/20210113110400.616319-3-hsinyi@chromium.org Signed-off-by: Matthias Brugger --- Documentation/devicetree/bindings/arm/mediatek.yaml | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/arm/mediatek.yaml b/Documentation/devicetree/bindings/arm/mediatek.yaml index 53f0d4e3ea98..93b3bdf6eaeb 100644 --- a/Documentation/devicetree/bindings/arm/mediatek.yaml +++ b/Documentation/devicetree/bindings/arm/mediatek.yaml @@ -120,7 +120,9 @@ properties: - const: mediatek,mt8183 - description: Google Krane (Lenovo IdeaPad Duet, 10e,...) items: - - const: google,krane-sku176 + - enum: + - google,krane-sku0 + - google,krane-sku176 - const: google,krane - const: mediatek,mt8183 From dc2e76175417e69c41d927dba75a966399f18354 Mon Sep 17 00:00:00 2001 From: Frank Wunderlich Date: Wed, 13 Jan 2021 19:09:19 +0100 Subject: [PATCH 451/584] dts64: mt7622: fix slow sd card access Fix extreme slow speed (200MB takes ~20 min) on writing sdcard on bananapi-r64 by adding reset-control for mmc1 like it's done for mmc0/emmc. Fixes: 2c002a3049f7 ("arm64: dts: mt7622: add mmc related device nodes") Signed-off-by: Frank Wunderlich Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210113180919.49523-1-linux@fw-web.de Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt7622.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi index 5b9ec032ce8d..7c6d871538a6 100644 --- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi @@ -698,6 +698,8 @@ clocks = <&pericfg CLK_PERI_MSDC30_1_PD>, <&topckgen CLK_TOP_AXI_SEL>; clock-names = "source", "hclk"; + resets = <&pericfg MT7622_PERI_MSDC1_SW_RST>; + reset-names = "hrst"; status = "disabled"; }; From f8919782d9e3967bc3779fa98df0e9d35e12f8ef Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:29 +0100 Subject: [PATCH 452/584] ARM: dts: sun6i: primo81: Remove useless io-channel-cells The mma8452 binding doesn't expect an io-channel-cells property, let's remove it. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-10-maxime@cerno.tech --- arch/arm/boot/dts/sun6i-a31s-primo81.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts index bc3170a0b8b5..0e1ee5ff2c2b 100644 --- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts @@ -115,7 +115,6 @@ reg = <0x1c>; interrupt-parent = <&pio>; interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; /* PA9 */ - #io-channel-cells = <1>; }; }; From 90c3047426fb42c6a6161cc065b05c630f71f7d1 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:30 +0100 Subject: [PATCH 453/584] ARM: dts: sun8i: nanopi-r1: Fix GPIO regulator state array Even though it translates to the same thing down to the binary level, we should have an array of 2 number cells to describe each voltage state, which in turns create a validation warning. Let's fix this. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-11-maxime@cerno.tech --- arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts index 204a39f93f4e..26e2e6172e0d 100644 --- a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts +++ b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts @@ -39,8 +39,8 @@ regulator-ramp-delay = <50>; gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */ gpios-states = <0x1>; - states = <1100000 0x0 - 1300000 0x1>; + states = <1100000 0x0>, + <1300000 0x1>; }; wifi_pwrseq: wifi_pwrseq { From 1231238cbb494bbe4527632a0933a901c6383243 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:31 +0100 Subject: [PATCH 454/584] ARM: dts: sun8i-s3: impetus: Fix the USB PHY ID detect GPIO properties While the USB PHY Device Tree mandates that the name of the ID detect pin should be usb0_id_det-gpios, a significant number of device tree use usb0_id_det-gpio instead. This was functional because the GPIO framework falls back to the gpio suffix that is legacy, but we should fix this. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-12-maxime@cerno.tech --- arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi b/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi index 24d507cdbcf9..052b010a5607 100644 --- a/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi +++ b/arch/arm/boot/dts/sun8i-s3-elimo-impetus.dtsi @@ -39,6 +39,6 @@ }; &usbphy { - usb0_id_det-gpio = <&pio 5 6 GPIO_ACTIVE_HIGH>; + usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; status = "okay"; }; From 7098a58320d9757307fccaa1eae4fa7a6d597f5b Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:32 +0100 Subject: [PATCH 455/584] ARM: dts: sun8i-s3: pinecube: Fix CSI DTC warnings Our CSI endpoint trigger some DTC warnings due to the fact that we're having a single endpoint that doesn't need any reg property, and since we don't have a reg property, we don't need the address-cells and size-cells properties anymore. Fix those Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-13-maxime@cerno.tech --- arch/arm/boot/dts/sun8i-s3-pinecube.dts | 3 --- 1 file changed, 3 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-s3-pinecube.dts b/arch/arm/boot/dts/sun8i-s3-pinecube.dts index 3c4bc4b0ca7f..20966e954eda 100644 --- a/arch/arm/boot/dts/sun8i-s3-pinecube.dts +++ b/arch/arm/boot/dts/sun8i-s3-pinecube.dts @@ -64,9 +64,6 @@ status = "okay"; port { - #address-cells = <1>; - #size-cells = <0>; - csi1_ep: endpoint { remote-endpoint = <&ov5640_ep>; bus-width = <8>; From d4a551ae1f905943ac8c7c3822230ba8de1a7a5f Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:33 +0100 Subject: [PATCH 456/584] ARM: dts: sun8i-a83t: Remove empty CSI port The empty CSI port triggers a dt-validate warning. Let's align with the other DTSI and remove it entirely, expecting the DTS to fill it. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-14-maxime@cerno.tech --- arch/arm/boot/dts/sun8i-a83t.dtsi | 3 --- 1 file changed, 3 deletions(-) diff --git a/arch/arm/boot/dts/sun8i-a83t.dtsi b/arch/arm/boot/dts/sun8i-a83t.dtsi index c010b27fdb6a..bd898b250e74 100644 --- a/arch/arm/boot/dts/sun8i-a83t.dtsi +++ b/arch/arm/boot/dts/sun8i-a83t.dtsi @@ -1061,9 +1061,6 @@ clock-names = "bus", "mod", "ram"; resets = <&ccu RST_BUS_CSI>; status = "disabled"; - - csi_in: port { - }; }; hdmi: hdmi@1ee0000 { From aaea73a96d134da2720bffd76408ac43d8e97918 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:34 +0100 Subject: [PATCH 457/584] ARM: dts: sun8i-a33: sina33: Add missing panel power supply The SinA33 panel is missing its power-supply property, even though the binding mandates it. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-15-maxime@cerno.tech --- arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts index 785798e3a104..a1f28e71aae4 100644 --- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts +++ b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts @@ -63,6 +63,7 @@ panel { compatible = "netron-dy,e231732"; + power-supply = <®_vcc3v3>; port { panel_input: endpoint { From a657efc5b6d1097ea05048263dabe9bee5d116a5 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:35 +0100 Subject: [PATCH 458/584] arm64: dts: allwinner: h6: Use - instead of @ for DT OPP entries DTC and the dt-validate tools report warnings for opp with the format opp@$frequency: dtc for a missing reg property, and dt-validate since the binding requires child nodes to have the format opp-$frequency. Change this to the latter format. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-16-maxime@cerno.tech --- .../boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi | 20 +++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi index 1a5eddc5a40f..8c6e8536b69f 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-cpu-opp.dtsi @@ -8,7 +8,7 @@ nvmem-cells = <&cpu_speed_grade>; opp-shared; - opp@480000000 { + opp-480000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <480000000>; @@ -17,7 +17,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@720000000 { + opp-720000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <720000000>; @@ -26,7 +26,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@816000000 { + opp-816000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <816000000>; @@ -35,7 +35,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@888000000 { + opp-888000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <888000000>; @@ -44,7 +44,7 @@ opp-microvolt-speed2 = <820000 820000 1200000>; }; - opp@1080000000 { + opp-1080000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1080000000>; @@ -53,7 +53,7 @@ opp-microvolt-speed2 = <880000 880000 1200000>; }; - opp@1320000000 { + opp-1320000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1320000000>; @@ -62,7 +62,7 @@ opp-microvolt-speed2 = <940000 940000 1200000>; }; - opp@1488000000 { + opp-1488000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1488000000>; @@ -71,7 +71,7 @@ opp-microvolt-speed2 = <1000000 1000000 1200000>; }; - opp@1608000000 { + opp-1608000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1608000000>; @@ -80,7 +80,7 @@ opp-microvolt-speed2 = <1030000 1030000 1200000>; }; - opp@1704000000 { + opp-1704000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1704000000>; @@ -89,7 +89,7 @@ opp-microvolt-speed2 = <1060000 1060000 1200000>; }; - opp@1800000000 { + opp-1800000000 { clock-latency-ns = <244144>; /* 8 32k periods */ opp-hz = /bits/ 64 <1800000000>; From d9997fe96d0d27fc0d2103477d8d4624ef8e7864 Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:36 +0100 Subject: [PATCH 459/584] arm64: dts: allwinner: pinephone: Remove useless light sensor supplies The stk3311 binding don't expect a vdd or leda power supplies. Remove them. Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-17-maxime@cerno.tech --- arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi | 2 -- 1 file changed, 2 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi index bbc26abb1e10..9f69d489a81d 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi @@ -183,8 +183,6 @@ reg = <0x48>; interrupt-parent = <&pio>; interrupts = <1 0 IRQ_TYPE_EDGE_FALLING>; /* PB0 */ - vdd-supply = <®_ldo_io0>; - leda-supply = <®_dldo1>; }; /* Accelerometer/gyroscope */ From f9740094f451b8da22b2705198987ac48c66f04b Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:37 +0100 Subject: [PATCH 460/584] arm64: dts: allwinner: pinetab: Fix the panel compatible The commit 7fa40ca7ef61 ("arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab") introduced an ili9881-based panel device node but didn't conform to the binding. Fix this. Fixes: 7fa40ca7ef61 ("arm64: allwinner: dts: a64: add DT for Early Adopter's PineTab") Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-18-maxime@cerno.tech --- .../boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts index 652fc0cce304..6265360ce623 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab-early-adopter.dts @@ -17,7 +17,7 @@ /delete-node/ panel@0; panel@0 { - compatible = "feixin,k101-im2byl02"; + compatible = "feixin,k101-im2byl02", "ilitek,ili9881c"; reg = <0>; power-supply = <®_dc1sw>; reset-gpios = <&pio 3 24 GPIO_ACTIVE_LOW>; /* PD24 */ From 94492618b2e481587dcf4579f180ededaae5f62a Mon Sep 17 00:00:00 2001 From: Maxime Ripard Date: Thu, 14 Jan 2021 12:35:38 +0100 Subject: [PATCH 461/584] arm64: dts: allwinner: pine-h64: Fix typos in BT GPIOs The commit 53441b8ef7de ("arm64: dts: allwinner: h6: PineH64 model B: Add bluetooth") introduced the Bluetooth chip for the PineH64 model B, but the GPIOs property didn't conform to the binding of the bluetooth chip. Let's fix this. Fixes: 53441b8ef7de ("arm64: dts: allwinner: h6: PineH64 model B: Add bluetooth") Signed-off-by: Maxime Ripard Acked-by: Chen-Yu Tsai Acked-by: Jernej Skrabec Link: https://lore.kernel.org/r/20210114113538.1233933-19-maxime@cerno.tech --- arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts index 645bd8761eb5..686f58e77004 100644 --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-pine-h64-model-b.dts @@ -43,8 +43,8 @@ bluetooth { compatible = "realtek,rtl8723bs-bt"; - device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ - host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ + device-wake-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ + host-wake-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ max-speed = <1500000>; }; From 50b459bc468c85ef69fc44856a9ed20610cdace3 Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sat, 16 Jan 2021 11:52:28 +0100 Subject: [PATCH 462/584] ARM: dts: sunxi: bananapi-m2-plus: Increase BT UART speed Bluetooth module on BananaPi M2 Plus can also be used for streaming audio. However, for that case higher UART speed is required. Add a max-speed property. Signed-off-by: Jernej Skrabec Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210116105228.847073-1-jernej.skrabec@siol.net --- arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi index 8e5cb3b3fd68..7a6af54dd342 100644 --- a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi +++ b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi @@ -219,6 +219,7 @@ bluetooth { compatible = "brcm,bcm43438-bt"; + max-speed = <1500000>; clocks = <&rtc 1>; clock-names = "lpo"; vbat-supply = <®_vcc3v3>; From f0e4a3b1929daa1a48d33c331c1d8432839ad769 Mon Sep 17 00:00:00 2001 From: Jernej Skrabec Date: Sat, 16 Jan 2021 11:37:10 +0100 Subject: [PATCH 463/584] ARM: dts: sun8i: h2-plus: bananapi-m2-zero: Increase BT UART speed Bluetooth module on BananaPi M2 Zero can also be used for streaming audio. However, for that case higher UART speed is required. Add a max-speed property. Signed-off-by: Jernej Skrabec Acked-by: Chen-Yu Tsai Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210116103710.245617-1-jernej.skrabec@siol.net --- arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts index f8a7b1371e97..f3f7a2c912ab 100644 --- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts +++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts @@ -154,6 +154,7 @@ bluetooth { compatible = "brcm,bcm43438-bt"; + max-speed = <1500000>; clocks = <&rtc 1>; clock-names = "lpo"; vbat-supply = <®_vcc3v3>; From 2977fcb7a974e64bdfe43d1114869afaec59d431 Mon Sep 17 00:00:00 2001 From: Samuel Holland Date: Sun, 17 Jan 2021 23:50:35 -0600 Subject: [PATCH 464/584] ARM: dts: sunxi: Rename nmi_intc to r_intc The R_INTC block controls more than just the NMI, and it is a different hardware block than the NMI INTC found in some other Allwinner SoCs, so the label "nmi_intc" is inaccurate. Name it "r_intc" to match the compatible and to match the few references in the vendor documentation. Signed-off-by: Samuel Holland Signed-off-by: Maxime Ripard Link: https://lore.kernel.org/r/20210118055040.21910-6-samuel@sholland.org --- arch/arm/boot/dts/sun6i-a31-hummingbird.dts | 2 +- arch/arm/boot/dts/sun6i-a31-m9.dts | 2 +- arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts | 2 +- arch/arm/boot/dts/sun6i-a31.dtsi | 2 +- arch/arm/boot/dts/sun6i-a31s-primo81.dts | 2 +- arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi | 2 +- arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts | 2 +- arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts | 2 +- arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi | 2 +- arch/arm/boot/dts/sun8i-a23-a33.dtsi | 2 +- arch/arm/boot/dts/sun8i-a33-olinuxino.dts | 2 +- arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts | 2 +- arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts | 2 +- arch/arm/boot/dts/sun8i-r16-parrot.dts | 2 +- arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi | 2 +- 15 files changed, 15 insertions(+), 15 deletions(-) diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts index 73de34ae37fd..486cec6f71e0 100644 --- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts +++ b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts @@ -226,7 +226,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun6i-a31-m9.dts b/arch/arm/boot/dts/sun6i-a31-m9.dts index aff716b523c4..e4f3415e6108 100644 --- a/arch/arm/boot/dts/sun6i-a31-m9.dts +++ b/arch/arm/boot/dts/sun6i-a31-m9.dts @@ -115,7 +115,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts index 959ed9ce4b48..7bd4bdd66a76 100644 --- a/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts +++ b/arch/arm/boot/dts/sun6i-a31-mele-a1000g-quad.dts @@ -115,7 +115,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index 92fd47c54d73..a75033e85fcb 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -1305,7 +1305,7 @@ clock-output-names = "osc32k"; }; - nmi_intc: interrupt-controller@1f00c00 { + r_intc: interrupt-controller@1f00c00 { compatible = "allwinner,sun6i-a31-r-intc"; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/sun6i-a31s-primo81.dts b/arch/arm/boot/dts/sun6i-a31s-primo81.dts index 0e1ee5ff2c2b..66bc6ca77afb 100644 --- a/arch/arm/boot/dts/sun6i-a31s-primo81.dts +++ b/arch/arm/boot/dts/sun6i-a31s-primo81.dts @@ -158,7 +158,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; x-powers,drive-vbus-en; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi index 3099491de8c4..7455c0db4a8a 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi +++ b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi @@ -78,7 +78,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts index b4ce60a3b194..efb25b949f30 100644 --- a/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-sinovoip-bpi-m2.dts @@ -148,7 +148,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; x-powers,drive-vbus-en; diff --git a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts index 2504e7189c54..cadc45255d7b 100644 --- a/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts +++ b/arch/arm/boot/dts/sun6i-a31s-yones-toptech-bs1078-v2.dts @@ -98,7 +98,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; }; }; diff --git a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi index 7de2abd541c1..6bf3fbdd738f 100644 --- a/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun6i-reference-design-tablet.dtsi @@ -79,7 +79,7 @@ axp22x: pmic@68 { compatible = "x-powers,axp221"; reg = <0x68>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; drivevbus-supply = <®_vcc5v0>; x-powers,drive-vbus-en; diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi index c1362d0f0ff8..a42fac676b31 100644 --- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi +++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi @@ -716,7 +716,7 @@ #clock-cells = <1>; }; - nmi_intc: interrupt-controller@1f00c00 { + r_intc: interrupt-controller@1f00c00 { compatible = "allwinner,sun6i-a31-r-intc"; interrupt-controller; #interrupt-cells = <2>; diff --git a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts index 9adf58f866d6..8538514c8588 100644 --- a/arch/arm/boot/dts/sun8i-a33-olinuxino.dts +++ b/arch/arm/boot/dts/sun8i-a33-olinuxino.dts @@ -98,7 +98,7 @@ axp22x: pmic@3a3 { compatible = "x-powers,axp223"; reg = <0x3a3>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; x-powers,drive-vbus-en; diff --git a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts index a1f28e71aae4..d54a067fc76e 100644 --- a/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts +++ b/arch/arm/boot/dts/sun8i-a33-sinlinx-sina33.dts @@ -165,7 +165,7 @@ axp22x: pmic@3a3 { compatible = "x-powers,axp223"; reg = <0x3a3>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; }; diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts index 015ba66fd277..293016d081cd 100644 --- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts +++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts @@ -163,7 +163,7 @@ axp22x: pmic@3a3 { compatible = "x-powers,axp223"; reg = <0x3a3>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; x-powers,drive-vbus-en; diff --git a/arch/arm/boot/dts/sun8i-r16-parrot.dts b/arch/arm/boot/dts/sun8i-r16-parrot.dts index 09a6a3b2cccc..2be1b76fe2f6 100644 --- a/arch/arm/boot/dts/sun8i-r16-parrot.dts +++ b/arch/arm/boot/dts/sun8i-r16-parrot.dts @@ -164,7 +164,7 @@ axp22x: pmic@3a3 { compatible = "x-powers,axp223"; reg = <0x3a3>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; drivevbus-supply = <®_vcc5v0>; x-powers,drive-vbus-en; diff --git a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi index daf4be6416df..797d61cff11e 100644 --- a/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi +++ b/arch/arm/boot/dts/sun8i-reference-design-tablet.dtsi @@ -93,7 +93,7 @@ axp22x: pmic@3a3 { compatible = "x-powers,axp223"; reg = <0x3a3>; - interrupt-parent = <&nmi_intc>; + interrupt-parent = <&r_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; eldoin-supply = <®_dcdc1>; drivevbus-supply = <®_vcc5v0>; From 18d6e3f6744d6105ab61de790170cb60534eeebc Mon Sep 17 00:00:00 2001 From: Matthias Brugger Date: Sun, 31 Jan 2021 11:17:26 +0100 Subject: [PATCH 465/584] arm64: dts: mt8183: Fix GCE include path The header file of GCE should be for MT8183 SoC instead of MT8173. Fixes: 91f9c963ce79 ("arm64: dts: mt8183: Add display nodes for MT8183") Reported-by: CK Hu Signed-off-by: Matthias Brugger Reviewed-by: Chun-Kuang Hu Link: https://lore.kernel.org/r/20210131101726.804-1-matthias.bgg@kernel.org Signed-off-by: Matthias Brugger --- arch/arm64/boot/dts/mediatek/mt8183.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi index b3b8afec5ab9..80519a145f13 100644 --- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi @@ -6,7 +6,7 @@ */ #include -#include +#include #include #include #include From 5f816e36e3d6b1ef54eee230c63c208a51d164bd Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:49 +0100 Subject: [PATCH 466/584] arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111 u48 chip on zcu111 is si5382 not si5328. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/cefda1a894fb54059aa1b018e4ecad0eb36fdc9d.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index 2e92634c77f9..d9a8fdbbcae8 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -410,7 +410,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <4>; - si5328: clock-generator@69 { /* SI5328 - u48 */ + si5382: clock-generator@69 { /* SI5382 - u48 */ reg = <0x69>; }; }; From 82a7ebf00224d411148062fac6e8a088419f222b Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:50 +0100 Subject: [PATCH 467/584] arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106 Origin DT binding just specify driver but wasn't aligned with DT binding which came later. Extend description for zcu102 and zcu106 to cover latest binding. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/82b2b13006307f108ace81c50c213c3857078b57.1611224800.git.michal.simek@xilinx.com --- .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 17 ++++++++++++++ .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 22 +++++++++++++++++++ 2 files changed, 39 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index f1255f635dfd..5ff7ab665374 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -132,6 +132,12 @@ compatible = "iio-hwmon"; io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>; }; + + refhdmi: refhdmi { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <114285000>; + }; }; &can1 { @@ -526,6 +532,17 @@ * interrupt-parent = <&>; * interrupts = <>; */ + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + clocks = <&refhdmi>; + clock-names = "xtal"; + clock-output-names = "si5328"; + + si5328_clk: clk0@0 { + reg = <0>; + clock-frequency = <27000000>; + }; }; }; /* 5 - 7 unconnected */ diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index 6e9efe233838..7910ac125101 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -132,6 +132,12 @@ compatible = "iio-hwmon"; io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>; }; + + refhdmi: refhdmi { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <114285000>; + }; }; &can1 { @@ -520,6 +526,22 @@ reg = <4>; si5328: clock-generator@69 {/* SI5328 - u20 */ reg = <0x69>; + /* + * Chip has interrupt present connected to PL + * interrupt-parent = <&>; + * interrupts = <>; + */ + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + clocks = <&refhdmi>; + clock-names = "xtal"; + clock-output-names = "si5328"; + + si5328_clk: clk0@0 { + reg = <0>; + clock-frequency = <27000000>; + }; }; }; i2c@5 { From 928a5747599e737bcddf36aaa0ed3cc7b7fd17ff Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:51 +0100 Subject: [PATCH 468/584] arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111 Enable si5341 driver is the main chip for providing preprogrammed clocks for the whole platform. # cat /sys/kernel/debug/clk/clk_summary ... refhdmi 1 1 0 114285000 0 0 50000 xtal_0 0 0 0 114285000 0 0 50000 pll_0 0 0 0 40731174000000 0 0 50000 clk1_0 0 0 0 27000000 0 0 50000 clk0_0 0 0 0 27000000 0 0 50000 ref48M 1 2 0 48000000 0 0 50000 si5341 0 4 0 14000000 0 0 50000 clock-generator.N4 0 0 0 0 0 0 50000 clock-generator.N3 0 1 0 733260000 0 0 50000 clock-generator.9 0 1 0 33330000 0 0 50000 clock-generator.N2 0 1 0 104000000 0 0 50000 clock-generator.2 0 1 0 26000000 0 0 50000 clock-generator.N1 0 2 0 594000000 0 0 50000 clock-generator.7 0 1 0 74250000 0 0 50000 clock-generator.0 0 1 0 27000000 0 0 50000 clock-generator.N0 0 4 0 1000000000 0 0 50000 clock-generator.8 0 0 0 0 0 0 50000 clock-generator.6 0 1 0 125000000 0 0 50000 clock-generator.5 0 1 0 100000000 0 0 50000 clock-generator.4 0 1 0 100000000 0 0 50000 clock-generator.3 0 1 0 125000000 0 0 50000 clock-generator.1 0 0 0 0 0 0 50000 ... Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/b93f13297684704a60e8d7274009a20aa98d14f7.1611224800.git.michal.simek@xilinx.com --- .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 56 ++++++++++++++++++- .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 45 +++++++++++++++ .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 46 ++++++++++++++- 3 files changed, 145 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index 5ff7ab665374..68c2ad30d62d 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -133,6 +133,13 @@ io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>; }; + /* 48MHz reference crystal */ + ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; + refhdmi: refhdmi { compatible = "fixed-clock"; #clock-cells = <0>; @@ -489,9 +496,56 @@ #size-cells = <0>; reg = <1>; si5341: clock-generator@36 { /* SI5341 - u69 */ + compatible = "silabs,si5341"; reg = <0x36>; - }; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + clock-output-names = "si5341"; + si5341_0: out@0 { + /* refclk0 for PS-GT, used for DP */ + reg = <0>; + always-on; + }; + si5341_2: out@2 { + /* refclk2 for PS-GT, used for USB3 */ + reg = <2>; + always-on; + }; + si5341_3: out@3 { + /* refclk3 for PS-GT, used for SATA */ + reg = <3>; + always-on; + }; + si5341_4: out@4 { + /* refclk4 for PS-GT, used for PCIE slot */ + reg = <4>; + always-on; + }; + si5341_5: out@5 { + /* refclk5 for PS-GT, used for PCIE */ + reg = <5>; + always-on; + }; + si5341_6: out@6 { + /* refclk6 PL CLK125 */ + reg = <6>; + always-on; + }; + si5341_7: out@7 { + /* refclk7 PL CLK74 */ + reg = <7>; + always-on; + }; + si5341_9: out@9 { + /* refclk9 used for PS_REF_CLK 33.3 MHz */ + reg = <9>; + always-on; + }; + }; }; i2c@2 { #address-cells = <1>; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index 7910ac125101..a29ff20090ce 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -133,6 +133,13 @@ io-channels = <&u75 0>, <&u75 1>, <&u75 2>, <&u75 3>; }; + /* 48MHz reference crystal */ + ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; + refhdmi: refhdmi { compatible = "fixed-clock"; #clock-cells = <0>; @@ -488,7 +495,45 @@ #size-cells = <0>; reg = <1>; si5341: clock-generator@36 { /* SI5341 - u69 */ + compatible = "silabs,si5341"; reg = <0x36>; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + clock-output-names = "si5341"; + + si5341_0: out@0 { + /* refclk0 for PS-GT, used for DP */ + reg = <0>; + always-on; + }; + si5341_2: out@2 { + /* refclk2 for PS-GT, used for USB3 */ + reg = <2>; + always-on; + }; + si5341_3: out@3 { + /* refclk3 for PS-GT, used for SATA */ + reg = <3>; + always-on; + }; + si5341_6: out@6 { + /* refclk6 PL CLK125 */ + reg = <6>; + always-on; + }; + si5341_7: out@7 { + /* refclk7 PL CLK74 */ + reg = <7>; + always-on; + }; + si5341_9: out@9 { + /* refclk9 used for PS_REF_CLK 33.3 MHz */ + reg = <9>; + always-on; + }; }; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index d9a8fdbbcae8..92b3cee62d11 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -116,6 +116,13 @@ compatible = "iio-hwmon"; io-channels = <&u79 0>, <&u79 1>, <&u79 2>, <&u79 3>; }; + + /* 48MHz reference crystal */ + ref48: ref48M { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <48000000>; + }; }; &dcc { @@ -374,9 +381,46 @@ #size-cells = <0>; reg = <1>; si5341: clock-generator@36 { /* SI5341 - u46 */ + compatible = "silabs,si5341"; reg = <0x36>; - }; + #clock-cells = <2>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&ref48>; + clock-names = "xtal"; + clock-output-names = "si5341"; + si5341_0: out@0 { + /* refclk0 for PS-GT, used for DP */ + reg = <0>; + always-on; + }; + si5341_2: out@2 { + /* refclk2 for PS-GT, used for USB3 */ + reg = <2>; + always-on; + }; + si5341_3: out@3 { + /* refclk3 for PS-GT, used for SATA */ + reg = <3>; + always-on; + }; + si5341_5: out@5 { + /* refclk5 PL CLK100 */ + reg = <5>; + always-on; + }; + si5341_6: out@6 { + /* refclk6 PL CLK125 */ + reg = <6>; + always-on; + }; + si5341_9: out@9 { + /* refclk9 used for PS_REF_CLK 33.3 MHz */ + reg = <9>; + always-on; + }; + }; }; i2c@2 { #address-cells = <1>; From 42cb66dcd5f7c40e31adc162122f6428021f97e5 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:52 +0100 Subject: [PATCH 469/584] arm64: dts: zynqmp: Enable reset controller driver Enable reset controller to be prepared for use. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/4fb62952f61e5046d750fff0e3e469c7abd1d0d0.1611224800.git.michal.simek@xilinx.com Reviewed-by: Laurent Pinchart --- arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index cdc1a0ddfa01..94a2e1f2b713 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -187,6 +187,11 @@ xlnx_aes: zynqmp-aes { compatible = "xlnx,zynqmp-aes"; }; + + zynqmp_reset: reset-controller { + compatible = "xlnx,zynqmp-reset"; + #reset-cells = <1>; + }; }; }; From 51733f16c6419df8b2cb4c254d249eae1e03d6c8 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:53 +0100 Subject: [PATCH 470/584] arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106 Enable psgtr driver and write clocks property to get sata to work. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/80b52ef97501968ee97fc152363bc4b9b7bb2cff.1611224800.git.michal.simek@xilinx.com --- .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 10 +++++++ .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 28 +++++++++++++++++++ .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 10 +++++++ .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 10 +++++++ 4 files changed, 58 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index 68c2ad30d62d..d92698ffbf8c 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -13,6 +13,7 @@ #include "zynqmp-clk-ccf.dtsi" #include #include +#include / { model = "ZynqMP ZCU102 RevA"; @@ -663,6 +664,13 @@ status = "okay"; }; +&psgtr { + status = "okay"; + /* pcie, sata, usb3, dp */ + clocks = <&si5341 0 5>, <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>; + clock-names = "ref0", "ref1", "ref2", "ref3"; +}; + &rtc { status = "okay"; }; @@ -678,6 +686,8 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index 7a4614e3f5fa..5e2be9abc175 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -12,6 +12,7 @@ #include "zynqmp.dtsi" #include "zynqmp-clk-ccf.dtsi" #include +#include / { model = "ZynqMP ZCU104 RevA"; @@ -36,6 +37,24 @@ device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; + + clock_8t49n287_5: clk125 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clock_8t49n287_2: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + clock_8t49n287_3: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; }; &can1 { @@ -158,6 +177,13 @@ status = "okay"; }; +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; + clock-names = "ref1", "ref2", "ref3"; +}; + &sata { status = "okay"; /* SATA OOB timing settings */ @@ -169,6 +195,8 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index a29ff20090ce..4ec6715abab7 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -13,6 +13,7 @@ #include "zynqmp-clk-ccf.dtsi" #include #include +#include / { model = "ZynqMP ZCU106 RevA"; @@ -658,6 +659,13 @@ }; }; +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>; + clock-names = "ref1", "ref2", "ref3"; +}; + &rtc { status = "okay"; }; @@ -673,6 +681,8 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index 92b3cee62d11..2969c4b71384 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -13,6 +13,7 @@ #include "zynqmp-clk-ccf.dtsi" #include #include +#include / { model = "ZynqMP ZCU111 RevA"; @@ -541,6 +542,13 @@ }; }; +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&si5341 0 3>, <&si5341 0 2>, <&si5341 0 0>; + clock-names = "ref1", "ref2", "ref3"; +}; + &rtc { status = "okay"; }; @@ -556,6 +564,8 @@ ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; }; /* SD1 with level shifter */ From 002002c0ad3155b1f85391183e341185d3777ab5 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:54 +0100 Subject: [PATCH 471/584] arm64: dts: zynqmp: Add label for zynqmp_ipi Add label which is used by bootloader for adding bootloader specific flag. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/3dc8416abdd3498e61edcd83830a12af295c5c6d.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 94a2e1f2b713..31c6943c6217 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -99,7 +99,7 @@ }; }; - zynqmp_ipi { + zynqmp_ipi: zynqmp_ipi { compatible = "xlnx,zynqmp-ipi-mailbox"; interrupt-parent = <&gic>; interrupts = <0 35 4>; From 63481699d6e35d38490e2a0b388999f8aa0945b3 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:55 +0100 Subject: [PATCH 472/584] arm64: dts: zynqmp: Add missing mio-bank properties to sdhcis Add missing xlnx,mio-bank property to sdhci nodes. Also add properties with 0 value to have it listed in case that files are copied to different projects where default case doesn't need to be handled in the same way. That's why explicitly list them too. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/dbdfcc1b25af8b28fc658a37ce18902978cb410d.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 2 ++ arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts | 1 + arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts | 1 + arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts | 1 + arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts | 1 + 5 files changed, 6 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts index 68ecd0f7b2f2..71ebcaadb7c8 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts @@ -233,11 +233,13 @@ status = "okay"; no-1-8-v; disable-wp; + xlnx,mio-bank = <0>; }; &sdhci1 { status = "okay"; bus-width = <0x4>; + xlnx,mio-bank = <0>; non-removable; disable-wp; cap-power-off-card; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index d92698ffbf8c..9abd10f6785a 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -694,6 +694,7 @@ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; }; &uart0 { diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index 5e2be9abc175..8ede619fea52 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -203,6 +203,7 @@ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; disable-wp; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index 4ec6715abab7..d60a30787022 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -689,6 +689,7 @@ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; }; &uart0 { diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index 2969c4b71384..758de05c4a4b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -572,6 +572,7 @@ &sdhci1 { status = "okay"; no-1-8-v; + xlnx,mio-bank = <1>; }; &uart0 { From 41b452a5702b4a35b4ddb12a83ca21875e366d50 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:56 +0100 Subject: [PATCH 473/584] arm64: dts: zynqmp: Wire arasan nand controller Add missing arasan controller with clocks. Disable it by default. Every board can enable it with specifying others properties. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/05cc1ce7973ac5200aeca428c137b422c827c5e8.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 ++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 12 ++++++++++++ 2 files changed, 16 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index c94c3bb67edc..7af57619436d 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -116,6 +116,10 @@ clocks = <&zynqmp_clk ADMA_REF>, <&zynqmp_clk LPD_LSBUS>; }; +&nand0 { + clocks = <&zynqmp_clk NAND_REF>, <&zynqmp_clk LPD_LSBUS>; +}; + &gem0 { clocks = <&zynqmp_clk LPD_LSBUS>, <&zynqmp_clk GEM0_REF>, <&zynqmp_clk GEM0_TX>, <&zynqmp_clk GEM0_RX>, diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 31c6943c6217..19b349f00ce7 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -462,6 +462,18 @@ interrupts = <0 112 4>; }; + nand0: nand-controller@ff100000 { + compatible = "xlnx,zynqmp-nand-controller", "arasan,nfc-v3p10"; + status = "disabled"; + reg = <0x0 0xff100000 0x0 0x1000>; + clock-names = "controller", "bus"; + interrupt-parent = <&gic>; + interrupts = <0 14 4>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&zynqmp_firmware PD_NAND>; + }; + gem0: ethernet@ff0b0000 { compatible = "cdns,zynqmp-gem", "cdns,gem"; status = "disabled"; From cbf8bed0e353516653d90b30ff20ac3318596d83 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:57 +0100 Subject: [PATCH 474/584] arm64: dts: zynqmp: Wire zynqmp qspi controller Add missing ZynqMP qspi IP. It works in single mode only. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/5cebbc59a452f282c4ce0f0e1dffecadac8f126a.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 ++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 14 ++++++++++++++ 2 files changed, 18 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index 7af57619436d..6a577e1383c1 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -164,6 +164,10 @@ clocks = <&zynqmp_clk PCIE_REF>; }; +&qspi { + clocks = <&zynqmp_clk QSPI_REF>, <&zynqmp_clk LPD_LSBUS>; +}; + &sata { clocks = <&zynqmp_clk SATA_REF>; }; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 19b349f00ce7..533c19b80283 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -595,6 +595,20 @@ }; }; + qspi: spi@ff0f0000 { + compatible = "xlnx,zynqmp-qspi-1.0"; + status = "disabled"; + clock-names = "ref_clk", "pclk"; + interrupts = <0 15 4>; + interrupt-parent = <&gic>; + num-cs = <1>; + reg = <0x0 0xff0f0000 0x0 0x1000>, + <0x0 0xc0000000 0x0 0x8000000>; + #address-cells = <1>; + #size-cells = <0>; + power-domains = <&zynqmp_firmware PD_QSPI>; + }; + psgtr: phy@fd400000 { compatible = "xlnx,zynqmp-psgtr-v1.1"; status = "disabled"; From 1f9fcf6573fbbc446cc71429b33d5e5a8c522e28 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:58 +0100 Subject: [PATCH 475/584] arm64: dts: zynqmp: Add missing lpd watchdog node Xilinx ZynqMP SoC has FPD (Full Power Domain) and LPD (Low Power Domain) watchdogs. There are cases where also LPD WDT should be used by Arm cores that's why list it with disabled status. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/0489a1d5528614f1d570ea153d38b813f0c1eb9f.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 ++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 9 +++++++++ 2 files changed, 13 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index 6a577e1383c1..3ca7e4ee51b5 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -223,3 +223,7 @@ &watchdog0 { clocks = <&zynqmp_clk WDT>; }; + +&lpd_watchdog { + clocks = <&zynqmp_clk LPD_WDT>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 533c19b80283..467f92c2044b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -786,5 +786,14 @@ reg = <0x0 0xfd4d0000 0x0 0x1000>; timeout-sec = <10>; }; + + lpd_watchdog: watchdog@ff150000 { + compatible = "cdns,wdt-r1p2"; + status = "disabled"; + interrupt-parent = <&gic>; + interrupts = <0 52 1>; + reg = <0x0 0xff150000 0x0 0x1000>; + timeout-sec = <10>; + }; }; }; From 8ac47837f0e0905526a53c69a425f27a34b5e426 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:26:59 +0100 Subject: [PATCH 476/584] arm64: dts: zynqmp: Add missing iommu IDs Add missing iommu IDs to all IPs which have IDs assigned. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/78afdafdc60c3182318894f2808f7f337a798278.1611224800.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 52 ++++++++++++++++++++++++++ 1 file changed, 52 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 467f92c2044b..66d53521ec58 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -270,6 +270,8 @@ interrupts = <0 124 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14e8>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -281,6 +283,8 @@ interrupts = <0 125 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14e9>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -292,6 +296,8 @@ interrupts = <0 126 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ea>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -303,6 +309,8 @@ interrupts = <0 127 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14eb>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -314,6 +322,8 @@ interrupts = <0 128 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ec>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -325,6 +335,8 @@ interrupts = <0 129 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ed>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -336,6 +348,8 @@ interrupts = <0 130 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ee>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -347,6 +361,8 @@ interrupts = <0 131 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <128>; + #stream-id-cells = <1>; + iommus = <&smmu 0x14ef>; power-domains = <&zynqmp_firmware PD_GDMA>; }; @@ -375,6 +391,8 @@ interrupts = <0 77 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x868>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -386,6 +404,8 @@ interrupts = <0 78 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x869>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -397,6 +417,8 @@ interrupts = <0 79 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86a>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -408,6 +430,8 @@ interrupts = <0 80 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86b>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -419,6 +443,8 @@ interrupts = <0 81 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86c>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -430,6 +456,8 @@ interrupts = <0 82 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86d>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -441,6 +469,8 @@ interrupts = <0 83 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86e>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -452,6 +482,8 @@ interrupts = <0 84 4>; clock-names = "clk_main", "clk_apb"; xlnx,bus-width = <64>; + #stream-id-cells = <1>; + iommus = <&smmu 0x86f>; power-domains = <&zynqmp_firmware PD_ADMA>; }; @@ -471,6 +503,8 @@ interrupts = <0 14 4>; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x872>; power-domains = <&zynqmp_firmware PD_NAND>; }; @@ -483,6 +517,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x874>; power-domains = <&zynqmp_firmware PD_ETH_0>; }; @@ -495,6 +531,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x875>; power-domains = <&zynqmp_firmware PD_ETH_1>; }; @@ -507,6 +545,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x876>; power-domains = <&zynqmp_firmware PD_ETH_2>; }; @@ -519,6 +559,8 @@ clock-names = "pclk", "hclk", "tx_clk"; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x877>; power-domains = <&zynqmp_firmware PD_ETH_3>; }; @@ -606,6 +648,8 @@ <0x0 0xc0000000 0x0 0x8000000>; #address-cells = <1>; #size-cells = <0>; + #stream-id-cells = <1>; + iommus = <&smmu 0x873>; power-domains = <&zynqmp_firmware PD_QSPI>; }; @@ -635,6 +679,9 @@ interrupt-parent = <&gic>; interrupts = <0 133 4>; power-domains = <&zynqmp_firmware PD_SATA>; + #stream-id-cells = <4>; + iommus = <&smmu 0x4c0>, <&smmu 0x4c1>, + <&smmu 0x4c2>, <&smmu 0x4c3>; }; sdhci0: mmc@ff160000 { @@ -644,6 +691,8 @@ interrupts = <0 48 4>; reg = <0x0 0xff160000 0x0 0x1000>; clock-names = "clk_xin", "clk_ahb"; + #stream-id-cells = <1>; + iommus = <&smmu 0x870>; #clock-cells = <1>; clock-output-names = "clk_out_sd0", "clk_in_sd0"; power-domains = <&zynqmp_firmware PD_SD_0>; @@ -656,6 +705,8 @@ interrupts = <0 49 4>; reg = <0x0 0xff170000 0x0 0x1000>; clock-names = "clk_xin", "clk_ahb"; + #stream-id-cells = <1>; + iommus = <&smmu 0x871>; #clock-cells = <1>; clock-output-names = "clk_out_sd1", "clk_in_sd1"; power-domains = <&zynqmp_firmware PD_SD_1>; @@ -664,6 +715,7 @@ smmu: iommu@fd800000 { compatible = "arm,mmu-500"; reg = <0x0 0xfd800000 0x0 0x20000>; + #iommu-cells = <1>; status = "disabled"; #global-interrupts = <1>; interrupt-parent = <&gic>; From 127b856f67fc7bf9f753f99d247347833543ee42 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:27:00 +0100 Subject: [PATCH 477/584] arm64: dts: zynqmp: Add description for zcu104 revC Xilinx ZynqMP zcu104 revC and newer board revisions have different i2c structure compare to revA. The rest of the board is the same from software perspective. Also enable DMAs and QSPI. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/17f68c235ea1ce96c3293ca0cf3178951d6663f7.1611224800.git.michal.simek@xilinx.com --- .../devicetree/bindings/arm/xilinx.yaml | 1 + arch/arm64/boot/dts/xilinx/Makefile | 1 + .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 282 ++++++++++++++++++ 3 files changed, 284 insertions(+) create mode 100644 arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts diff --git a/Documentation/devicetree/bindings/arm/xilinx.yaml b/Documentation/devicetree/bindings/arm/xilinx.yaml index e0c6787f6e94..ae0ef1bf7965 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.yaml +++ b/Documentation/devicetree/bindings/arm/xilinx.yaml @@ -91,6 +91,7 @@ properties: items: - enum: - xlnx,zynqmp-zcu104-revA + - xlnx,zynqmp-zcu104-revC - xlnx,zynqmp-zcu104-rev1.0 - const: xlnx,zynqmp-zcu104 - const: xlnx,zynqmp diff --git a/arch/arm64/boot/dts/xilinx/Makefile b/arch/arm64/boot/dts/xilinx/Makefile index 60f5443f3ef4..11fb4fd3ebd4 100644 --- a/arch/arm64/boot/dts/xilinx/Makefile +++ b/arch/arm64/boot/dts/xilinx/Makefile @@ -13,5 +13,6 @@ dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-revB.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu102-rev1.0.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revA.dtb +dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu104-revC.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu106-revA.dtb dtb-$(CONFIG_ARCH_ZYNQMP) += zynqmp-zcu111-revA.dtb diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts new file mode 100644 index 000000000000..414f98f1831e --- /dev/null +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts @@ -0,0 +1,282 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * dts file for Xilinx ZynqMP ZCU104 + * + * (C) Copyright 2017 - 2020, Xilinx, Inc. + * + * Michal Simek + */ + +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include +#include + +/ { + model = "ZynqMP ZCU104 RevC"; + compatible = "xlnx,zynqmp-zcu104-revC", "xlnx,zynqmp-zcu104", "xlnx,zynqmp"; + + aliases { + ethernet0 = &gem3; + i2c0 = &i2c1; + mmc0 = &sdhci1; + rtc0 = &rtc; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &dcc; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + ina226 { + compatible = "iio-hwmon"; + io-channels = <&u183 0>, <&u183 1>, <&u183 2>, <&u183 3>; + }; + + clock_8t49n287_5: clk125 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <125000000>; + }; + + clock_8t49n287_2: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + clock_8t49n287_3: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; +}; + +&can1 { + status = "okay"; +}; + +&dcc { + status = "okay"; +}; + +&fpd_dma_chan1 { + status = "okay"; +}; + +&fpd_dma_chan2 { + status = "okay"; +}; + +&fpd_dma_chan3 { + status = "okay"; +}; + +&fpd_dma_chan4 { + status = "okay"; +}; + +&fpd_dma_chan5 { + status = "okay"; +}; + +&fpd_dma_chan6 { + status = "okay"; +}; + +&fpd_dma_chan7 { + status = "okay"; +}; + +&fpd_dma_chan8 { + status = "okay"; +}; + +&gem3 { + status = "okay"; + phy-handle = <&phy0>; + phy-mode = "rgmii-id"; + phy0: ethernet-phy@c { + reg = <0xc>; + ti,rx-internal-delay = <0x8>; + ti,tx-internal-delay = <0xa>; + ti,fifo-depth = <0x1>; + ti,dp83867-rxctrl-strap-quirk; + }; +}; + +&gpio { + status = "okay"; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <400000>; + + tca6416_u97: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + gpio-controller; + #gpio-cells = <2>; + /* + * IRQ not connected + * Lines: + * 0 - IRPS5401_ALERT_B + * 1 - HDMI_8T49N241_INT_ALM + * 2 - MAX6643_OT_B + * 3 - MAX6643_FANFAIL_B + * 5 - IIC_MUX_RESET_B + * 6 - GEM3_EXP_RESET_B + * 7 - FMC_LPC_PRSNT_M2C_B + * 4, 10 - 17 - not connected + */ + }; + + /* Another connection to this bus via PL i2c via PCA9306 - u45 */ + i2c-mux@74 { /* u34 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x74>; + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + /* + * IIC_EEPROM 1kB memory which uses 256B blocks + * where every block has different address. + * 0 - 256B address 0x54 + * 256B - 512B address 0x55 + * 512B - 768B address 0x56 + * 768B - 1024B address 0x57 + */ + eeprom: eeprom@54 { /* u23 */ + compatible = "atmel,24c08"; + reg = <0x54>; + #address-cells = <1>; + #size-cells = <1>; + }; + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + clock_8t49n287: clock-generator@6c { /* 8T49N287 - u182 */ + reg = <0x6c>; + }; + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + irps5401_43: irps5401@43 { /* IRPS5401 - u175 */ + compatible = "infineon,irps5401"; + reg = <0x43>; /* pmbus / i2c 0x13 */ + }; + irps5401_44: irps5401@44 { /* IRPS5401 - u180 */ + compatible = "infineon,irps5401"; + reg = <0x44>; /* pmbus / i2c 0x14 */ + }; + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + u183: ina226@40 { /* u183 */ + compatible = "ti,ina226"; + #io-channel-cells = <1>; + reg = <0x40>; + shunt-resistor = <5000>; + }; + }; + + i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + }; + + i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + }; + + /* 4, 6 not connected */ + }; +}; + +&qspi { + status = "okay"; + flash@0 { + compatible = "m25p80", "jedec,spi-nor"; /* n25q512a 128MiB */ + #address-cells = <1>; + #size-cells = <1>; + reg = <0x0>; + }; +}; + +&rtc { + status = "okay"; +}; + +&psgtr { + status = "okay"; + /* nc, sata, usb3, dp */ + clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>; + clock-names = "ref1", "ref2", "ref3"; +}; + +&sata { + status = "okay"; + /* SATA OOB timing settings */ + ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; + ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; + ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; + ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; + ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; + ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; + ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; + phy-names = "sata-phy"; + phys = <&psgtr 3 PHY_TYPE_SATA 1 1>; +}; + +/* SD1 with level shifter */ +&sdhci1 { + status = "okay"; + no-1-8-v; + xlnx,mio-bank = <1>; + disable-wp; +}; + +&uart0 { + status = "okay"; +}; + +&uart1 { + status = "okay"; +}; + +/* ULPI SMSC USB3320 */ +&usb0 { + status = "okay"; + dr_mode = "host"; +}; + +&watchdog0 { + status = "okay"; +}; From 1cabd1181f157f2d00b81653af4c276119f8cfb3 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 11:56:03 +0100 Subject: [PATCH 478/584] dt-bindings: arm: Fix typo in zcu111 board Trivial fix. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/13d064fc4850f96904a04e330cea5295d3751e46.1611226560.git.michal.simek@xilinx.com --- Documentation/devicetree/bindings/arm/xilinx.yaml | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/Documentation/devicetree/bindings/arm/xilinx.yaml b/Documentation/devicetree/bindings/arm/xilinx.yaml index ae0ef1bf7965..97e77b4e077c 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.yaml +++ b/Documentation/devicetree/bindings/arm/xilinx.yaml @@ -108,7 +108,7 @@ properties: items: - enum: - xlnx,zynqmp-zcu111-revA - - xlnx,zynqmp-zcu11-rev1.0 + - xlnx,zynqmp-zcu111-rev1.0 - const: xlnx,zynqmp-zcu111 - const: xlnx,zynqmp From 7b6714b3edeb98c6903cb8d74c7528fc3fc70538 Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Thu, 21 Jan 2021 13:36:05 +0100 Subject: [PATCH 479/584] arm64: dts: zynqmp: Add DPDMA node Add a DT node for the DisplayPort DMA engine (DPDMA). Signed-off-by: Laurent Pinchart Acked-by: Michal Simek Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/3d11015512a085592f2aca76eeddc04178d38bbe.1611232558.git.michal.simek@xilinx.com --- arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 4 ++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 10 ++++++++++ 2 files changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index 3ca7e4ee51b5..c676afc95f6d 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -227,3 +227,7 @@ &lpd_watchdog { clocks = <&zynqmp_clk LPD_WDT>; }; + +&zynqmp_dpdma { + clocks = <&zynqmp_clk DPDMA_REF>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index 66d53521ec58..f12cd24adbee 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -847,5 +847,15 @@ reg = <0x0 0xff150000 0x0 0x1000>; timeout-sec = <10>; }; + + zynqmp_dpdma: dma-controller@fd4c0000 { + compatible = "xlnx,zynqmp-dpdma"; + status = "disabled"; + reg = <0x0 0xfd4c0000 0x0 0x1000>; + interrupts = <0 122 4>; + interrupt-parent = <&gic>; + clock-names = "axi_clk"; + #dma-cells = <1>; + }; }; }; From b0f89cf5b62784823e1661780e846ea58d0816ce Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Thu, 21 Jan 2021 13:36:06 +0100 Subject: [PATCH 480/584] arm64: dts: zynqmp: Add DisplayPort subsystem Add a DT node for the DisplayPort subsystem, a hard IP present in the Zynq Ultrascale+ MPSoC. Signed-off-by: Laurent Pinchart Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/4d978aef852cacdfb35aa8e50d648a787e73b90c.1611232558.git.michal.simek@xilinx.com --- .../arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi | 6 +++++ arch/arm64/boot/dts/xilinx/zynqmp.dtsi | 22 +++++++++++++++++++ 2 files changed, 28 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi index c676afc95f6d..cf5295224750 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi @@ -231,3 +231,9 @@ &zynqmp_dpdma { clocks = <&zynqmp_clk DPDMA_REF>; }; + +&zynqmp_dpsub { + clocks = <&zynqmp_clk TOPSW_LSBUS>, + <&zynqmp_clk DP_AUDIO_REF>, + <&zynqmp_clk DP_VIDEO_REF>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi index f12cd24adbee..a3b391d18787 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi +++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi @@ -12,6 +12,7 @@ * the License, or (at your option) any later version. */ +#include #include #include @@ -857,5 +858,26 @@ clock-names = "axi_clk"; #dma-cells = <1>; }; + + zynqmp_dpsub: display@fd4a0000 { + compatible = "xlnx,zynqmp-dpsub-1.7"; + status = "disabled"; + reg = <0x0 0xfd4a0000 0x0 0x1000>, + <0x0 0xfd4aa000 0x0 0x1000>, + <0x0 0xfd4ab000 0x0 0x1000>, + <0x0 0xfd4ac000 0x0 0x1000>; + reg-names = "dp", "blend", "av_buf", "aud"; + interrupts = <0 119 4>; + interrupt-parent = <&gic>; + clock-names = "dp_apb_clk", "dp_aud_clk", + "dp_vtc_pixel_clk_in"; + power-domains = <&zynqmp_firmware PD_DP>; + resets = <&zynqmp_reset ZYNQMP_RESET_DP>; + dma-names = "vid0", "vid1", "vid2", "gfx0"; + dmas = <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO0>, + <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO1>, + <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO2>, + <&zynqmp_dpdma ZYNQMP_DPDMA_GRAPHICS>; + }; }; }; From 55563399bb16906b3e179dbeb66c0bf44c21b12a Mon Sep 17 00:00:00 2001 From: Laurent Pinchart Date: Thu, 21 Jan 2021 13:36:07 +0100 Subject: [PATCH 481/584] arm64: dts: zynqmp: Wire up the DisplayPort subsystem Enable the dpsub device and wire it up to the PS-GTR PHY lanes routed to the DisplayPort connector. Signed-off-by: Laurent Pinchart Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/9769d4d103b6eb75e3324825117f6832a746004e.1611232558.git.michal.simek@xilinx.com --- .../boot/dts/xilinx/zynqmp-zcu100-revC.dts | 31 +++++++++++++++++++ .../boot/dts/xilinx/zynqmp-zcu102-revA.dts | 10 ++++++ .../boot/dts/xilinx/zynqmp-zcu104-revA.dts | 11 +++++++ .../boot/dts/xilinx/zynqmp-zcu104-revC.dts | 11 +++++++ .../boot/dts/xilinx/zynqmp-zcu106-revA.dts | 11 +++++++ .../boot/dts/xilinx/zynqmp-zcu111-revA.dts | 11 +++++++ 6 files changed, 85 insertions(+) diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts index 71ebcaadb7c8..a53598c3624b 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts @@ -15,6 +15,7 @@ #include #include #include +#include / { model = "ZynqMP ZCU100 RevC"; @@ -108,6 +109,18 @@ compatible = "iio-hwmon"; io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>; }; + + si5335a_0: clk26 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + si5335a_1: clk27 { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; }; &dcc { @@ -224,6 +237,13 @@ }; }; +&psgtr { + status = "okay"; + /* usb3, dps */ + clocks = <&si5335a_0>, <&si5335a_1>; + clock-names = "ref0", "ref1"; +}; + &rtc { status = "okay"; }; @@ -295,3 +315,14 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 1>, + <&psgtr 0 PHY_TYPE_DP 1 1>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts index 9abd10f6785a..12e8bd48dc8c 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts @@ -714,3 +714,13 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts index 8ede619fea52..5637e1c17fdf 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revA.dts @@ -224,3 +224,14 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts index 414f98f1831e..7f2e32831b05 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts @@ -280,3 +280,14 @@ &watchdog0 { status = "okay"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts index d60a30787022..18771e868399 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts @@ -156,6 +156,17 @@ status = "okay"; }; +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 3>, + <&psgtr 0 PHY_TYPE_DP 1 3>; +}; + /* fpd_dma clk 667MHz, lpd_dma 500MHz */ &fpd_dma_chan1 { status = "okay"; diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts index 758de05c4a4b..d4b68f0d0098 100644 --- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts @@ -584,3 +584,14 @@ status = "okay"; dr_mode = "host"; }; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 1>, + <&psgtr 0 PHY_TYPE_DP 1 1>; +}; From 1e58ba111421375c5948c3e8145bdd84b06ac095 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Uwe=20Kleine-K=C3=B6nig?= Date: Sun, 24 Jan 2021 22:03:28 +0100 Subject: [PATCH 482/584] arm64: dts: rockchip: Rely on SoC external pull up on pmic-int-l on Helios64 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit According to the schematic there is an external pull up, so there is no need to enable the internal one additionally. Using no pull up matches the vendor device tree. Signed-off-by: Uwe Kleine-König Link: https://lore.kernel.org/r/20210124210328.611707-2-uwe@kleine-koenig.org Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts index 2a561be724b2..66c725a34220 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts @@ -331,7 +331,7 @@ pmic { pmic_int_l: pmic-int-l { - rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>; + rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>; }; }; From 5b9312109135b68b78b5a8e20d8f78b6bd9fb4fa Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Fri, 22 Jan 2021 18:12:43 +0100 Subject: [PATCH 483/584] arm64: dts: rockchip: fix ranges property format for rk3399 pcie node A test with the command below gives for example this error: /arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: pcie@f8000000: ranges: 'oneOf' conditional failed, one must be fixed: The pcie ranges property is an array. The dt-check expects that each array item is wrapped with angle brackets, so fix that ranges property format for the rk3399 pcie node. make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/ schemas/pci/pci-bus.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210122171243.16138-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3399.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index 4983dd18b4d8..fba9bcb3a08d 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -259,8 +259,8 @@ <&pcie_phy 2>, <&pcie_phy 3>; phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; - ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x1e00000 - 0x81000000 0x0 0xfbe00000 0x0 0xfbe00000 0x0 0x100000>; + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x1e00000>, + <0x81000000 0x0 0xfbe00000 0x0 0xfbe00000 0x0 0x100000>; resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>, <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, From 833821eeab916631d0cd22dbcda8db4b2a3acc3d Mon Sep 17 00:00:00 2001 From: Robin Murphy Date: Thu, 21 Jan 2021 00:00:13 +0000 Subject: [PATCH 484/584] arm64: dts: rockchip: Light "sys" LED on NanoPi R2S Set NanoPi R2S's "sys" LED to be on by default. This matches the behaviour of the stock FriendlyWRT image, and makes it much easier to tell when the thing has finished booting. Suitable triggers for the two network LEDs cannot realistically be configured from DT, so leave them be. Signed-off-by: Robin Murphy Link: https://lore.kernel.org/r/f066be60aa99460a45d04113c5e507d6602186f1.1611187213.git.robin.murphy@arm.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts index 2ee07d15a6e3..5382cf4fe353 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts +++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts @@ -50,6 +50,7 @@ sys_led: led-1 { gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>; label = "nanopi-r2s:red:sys"; + default-state = "on"; }; wan_led: led-2 { From 9e8244495f442bb951a354c4d240a97f423e3f14 Mon Sep 17 00:00:00 2001 From: Robin Murphy Date: Wed, 20 Jan 2021 23:42:21 +0000 Subject: [PATCH 485/584] arm64: dts: rockchip: Remove bogus "amba" bus nodes The "amba" bus nodes wrapping all the DMA-330 nodes serve no useful purpose, and certainly bear no relation at all to the actual underlying interconnect topology. They appear to be cargo-cult copying from a design misstep in the very early days of FDT adoption on ARM, which was righted with the "arm,primecell" compatible, and the last trace of the idea finally purged by commit 2ef7d5f342c1 ("ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus""). As such, they can simply be removed and the DMA-330 nodes fitted into the normal sort order. Signed-off-by: Robin Murphy Link: https://lore.kernel.org/r/131e0ea065109760ea3b59c4bb90cf4fac7826f7.1611186142.git.robin.murphy@arm.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/px30.dtsi | 25 ++++------- arch/arm64/boot/dts/rockchip/rk3308.dtsi | 45 ++++++++----------- arch/arm64/boot/dts/rockchip/rk3328.dtsi | 29 +++++-------- arch/arm64/boot/dts/rockchip/rk3368.dtsi | 55 +++++++++++------------- arch/arm64/boot/dts/rockchip/rk3399.dtsi | 51 ++++++++++------------ 5 files changed, 85 insertions(+), 120 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi index 6a3e57761b25..f2ce48f5b4e4 100644 --- a/arch/arm64/boot/dts/rockchip/px30.dtsi +++ b/arch/arm64/boot/dts/rockchip/px30.dtsi @@ -703,22 +703,15 @@ clock-names = "pclk", "timer"; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - dmac: dmac@ff240000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff240000 0x0 0x4000>; - interrupts = , - ; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC>; - clock-names = "apb_pclk"; - #dma-cells = <1>; - }; + dmac: dmac@ff240000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff240000 0x0 0x4000>; + interrupts = , + ; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC>; + clock-names = "apb_pclk"; + #dma-cells = <1>; }; tsadc: tsadc@ff280000 { diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi index 7211fab7a6e4..4ea32e8f33d2 100644 --- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi @@ -513,33 +513,26 @@ status = "disabled"; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; + dmac0: dma-controller@ff2c0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff2c0000 0x0 0x4000>; + interrupts = , + ; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC0>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + }; - dmac0: dma-controller@ff2c0000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff2c0000 0x0 0x4000>; - interrupts = , - ; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC0>; - clock-names = "apb_pclk"; - #dma-cells = <1>; - }; - - dmac1: dma-controller@ff2d0000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff2d0000 0x0 0x4000>; - interrupts = , - ; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC1>; - clock-names = "apb_pclk"; - #dma-cells = <1>; - }; + dmac1: dma-controller@ff2d0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff2d0000 0x0 0x4000>; + interrupts = , + ; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC1>; + clock-names = "apb_pclk"; + #dma-cells = <1>; }; i2s_2ch_0: i2s@ff350000 { diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi index 17709faf651b..063ed0adbec4 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi @@ -145,24 +145,6 @@ }; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - dmac: dmac@ff1f0000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff1f0000 0x0 0x4000>; - interrupts = , - ; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC>; - clock-names = "apb_pclk"; - #dma-cells = <1>; - }; - }; - analog_sound: analog-sound { compatible = "simple-audio-card"; simple-audio-card,format = "i2s"; @@ -507,6 +489,17 @@ status = "disabled"; }; + dmac: dmac@ff1f0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff1f0000 0x0 0x4000>; + interrupts = , + ; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + }; + thermal-zones { soc_thermal: soc-thermal { polling-delay-passive = <20>; diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index f6be54fdaa34..023ac25d69b7 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -136,37 +136,6 @@ }; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - dmac_peri: dma-controller@ff250000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff250000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC_PERI>; - clock-names = "apb_pclk"; - }; - - dmac_bus: dma-controller@ff600000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff600000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-broken-no-flushp; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC_BUS>; - clock-names = "apb_pclk"; - }; - }; - arm-pmu { compatible = "arm,armv8-pmuv3"; interrupts = , @@ -399,6 +368,18 @@ status = "disabled"; }; + dmac_peri: dma-controller@ff250000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff250000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC_PERI>; + clock-names = "apb_pclk"; + }; + thermal-zones { cpu_thermal: cpu-thermal { polling-delay-passive = <100>; /* milliseconds */ @@ -532,6 +513,18 @@ status = "disabled"; }; + dmac_bus: dma-controller@ff600000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff600000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-broken-no-flushp; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC_BUS>; + clock-names = "apb_pclk"; + }; + i2c0: i2c@ff650000 { compatible = "rockchip,rk3368-i2c", "rockchip,rk3288-i2c"; reg = <0x0 0xff650000 0x0 0x1000>; diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi index fba9bcb3a08d..4fa54c331982 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi @@ -200,35 +200,6 @@ #clock-cells = <0>; }; - amba: bus { - compatible = "simple-bus"; - #address-cells = <2>; - #size-cells = <2>; - ranges; - - dmac_bus: dma-controller@ff6d0000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff6d0000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC0_PERILP>; - clock-names = "apb_pclk"; - }; - - dmac_peri: dma-controller@ff6e0000 { - compatible = "arm,pl330", "arm,primecell"; - reg = <0x0 0xff6e0000 0x0 0x4000>; - interrupts = , - ; - #dma-cells = <1>; - arm,pl330-periph-burst; - clocks = <&cru ACLK_DMAC1_PERILP>; - clock-names = "apb_pclk"; - }; - }; - pcie0: pcie@f8000000 { compatible = "rockchip,rk3399-pcie"; reg = <0x0 0xf8000000 0x0 0x2000000>, @@ -1351,6 +1322,28 @@ }; }; + dmac_bus: dma-controller@ff6d0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff6d0000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC0_PERILP>; + clock-names = "apb_pclk"; + }; + + dmac_peri: dma-controller@ff6e0000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x0 0xff6e0000 0x0 0x4000>; + interrupts = , + ; + #dma-cells = <1>; + arm,pl330-periph-burst; + clocks = <&cru ACLK_DMAC1_PERILP>; + clock-names = "apb_pclk"; + }; + pmucru: pmu-clock-controller@ff750000 { compatible = "rockchip,rk3399-pmucru"; reg = <0x0 0xff750000 0x0 0x1000>; From c73583c625becd53930722471ff066360f68f5d9 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Mon, 18 Jan 2021 19:00:54 +0100 Subject: [PATCH 486/584] arm64: dts: rockchip: cleanup cpu_thermal node of rk3399-rock960.dts The cpu_thermal node in the rk3399-rock960.dts file does not reference &cpu_thermal directly to add the board-specific parts, but also repeats all the SoC default properties. Clean the whole thing up and fix alignment. Place new nodes in the correct alphabetical order. Compered to rk3399.dtsi the temperature property in cpu_alert0 changes from <70000> to <65000>. A sustainable-power property was added. The trip property in cooling map0 points to <&cpu_alert1> instead of <&cpu_alert0>. Suggested-by: Robin Murphy Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210118180054.9360-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- .../boot/dts/rockchip/rk3399-rock960.dts | 53 +++++-------------- 1 file changed, 14 insertions(+), 39 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts index b207740819ef..1a23e8f3cdf6 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts +++ b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dts @@ -63,6 +63,20 @@ }; +&cpu_alert0 { + temperature = <65000>; +}; + +&cpu_thermal { + sustainable-power = <1550>; + + cooling-maps { + map0 { + trip = <&cpu_alert1>; + }; + }; +}; + &pcie0 { ep-gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_HIGH>; }; @@ -125,45 +139,6 @@ status = "okay"; }; -&thermal_zones { - cpu_thermal: cpu-thermal { - polling-delay-passive = <100>; - polling-delay = <1000>; - thermal-sensors = <&tsadc 0>; - sustainable-power = <1550>; - - trips { - cpu_alert0: cpu_alert0 { - temperature = <65000>; - hysteresis = <2000>; - type = "passive"; - }; - - cpu_alert1: cpu_alert1 { - temperature = <75000>; - hysteresis = <2000>; - type = "passive"; - }; - - cpu_crit: cpu_crit { - temperature = <95000>; - hysteresis = <2000>; - type = "critical"; - }; - }; - - cooling-maps { - map0 { - - trip = <&cpu_alert1>; - cooling-device = - <&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, - <&cpu_b1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; - }; - }; - }; -}; - &usbdrd_dwc3_0 { dr_mode = "otg"; }; From 84b2c2c872da14971cbe9d946cd4687e1e3c1422 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Mon, 18 Jan 2021 16:52:40 +0100 Subject: [PATCH 487/584] arm64: dts: rockchip: assign a fixed index to mmc devices on px30 boards Recently introduced async probe on mmc devices can shuffle block IDs. Pin them to fixed values to ease booting in environments where UUIDs are not practical. Use newly introduced aliases for mmcblk devices from [1]. The sort order is based on reg address. [1] https://patchwork.kernel.org/patch/11747669/ Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210118155242.7172-3-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/px30.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi index f2ce48f5b4e4..2c8ea4ac856b 100644 --- a/arch/arm64/boot/dts/rockchip/px30.dtsi +++ b/arch/arm64/boot/dts/rockchip/px30.dtsi @@ -25,6 +25,9 @@ i2c1 = &i2c1; i2c2 = &i2c2; i2c3 = &i2c3; + mmc0 = &sdmmc; + mmc1 = &sdio; + mmc2 = &emmc; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; From b4a9fe3639953022e5ed9c19da1865f6dd5f110c Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Mon, 18 Jan 2021 16:52:41 +0100 Subject: [PATCH 488/584] arm64: dts: rockchip: assign a fixed index to mmc devices on rk3308 boards Recently introduced async probe on mmc devices can shuffle block IDs. Pin them to fixed values to ease booting in environments where UUIDs are not practical. Use newly introduced aliases for mmcblk devices from [1]. The sort order is based on reg address. [1] https://patchwork.kernel.org/patch/11747669/ Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210118155242.7172-4-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3308.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi index 4ea32e8f33d2..3a035a189450 100644 --- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi @@ -24,6 +24,9 @@ i2c1 = &i2c1; i2c2 = &i2c2; i2c3 = &i2c3; + mmc0 = &sdmmc; + mmc1 = &emmc; + mmc2 = &sdio; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; From 0523b124aa4d51e6e05cd22ffe77aaa471ec8b58 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Mon, 18 Jan 2021 16:52:42 +0100 Subject: [PATCH 489/584] arm64: dts: rockchip: assign a fixed index to mmc devices on rk3368 boards Recently introduced async probe on mmc devices can shuffle block IDs. Pin them to fixed values to ease booting in environments where UUIDs are not practical. Use newly introduced aliases for mmcblk devices from [1]. The sort order is based on reg address. [1] https://patchwork.kernel.org/patch/11747669/ Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210118155242.7172-5-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3368.dtsi | 3 +++ 1 file changed, 3 insertions(+) diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi index 023ac25d69b7..7af68ec3feae 100644 --- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi @@ -25,6 +25,9 @@ i2c3 = &i2c3; i2c4 = &i2c4; i2c5 = &i2c5; + mmc0 = &sdmmc; + mmc1 = &sdio0; + mmc2 = &emmc; serial0 = &uart0; serial1 = &uart1; serial2 = &uart2; From 060b65d260c5867ca9f56e275d8dbc3f5dba1c13 Mon Sep 17 00:00:00 2001 From: Johan Jonker Date: Sun, 10 Jan 2021 20:48:51 +0100 Subject: [PATCH 490/584] arm64: dts: rockchip: rename pinctrl nodename to gmac2io for nanopi-r2s board A test with the command below gives this error: /arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml: ethernet-phy: 'reg' is a required property The pinctrl nodename "ethernet-phy" conflicts with the rules in the "ethernet-phy.yaml" document, so rename it to "gmac2io". make ARCH=arm64 dtbs_check DT_SCHEMA_FILES=Documentation/devicetree/bindings/net/ethernet-phy.yaml Signed-off-by: Johan Jonker Link: https://lore.kernel.org/r/20210110194851.10207-1-jbx6244@gmail.com Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts index 5382cf4fe353..549121b34d88 100644 --- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts +++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts @@ -281,7 +281,7 @@ }; }; - ethernet-phy { + gmac2io { eth_phy_reset_pin: eth-phy-reset-pin { rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>; }; From 7582ad63c9bd09a8f0988c46074481ddd4f92e04 Mon Sep 17 00:00:00 2001 From: Katsuhiro Suzuki Date: Mon, 11 Jan 2021 00:19:13 +0900 Subject: [PATCH 491/584] arm64: dts: rockchip: more user friendly name of sound nodes This patch changes device name to more user friendly name of Analog and SPDIF sound nodes for rk3399-rockpro64. Signed-off-by: Katsuhiro Suzuki Link: https://lore.kernel.org/r/20210110151913.3615326-1-katsuhiro@katsuster.net Signed-off-by: Heiko Stuebner --- arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi index 58097245994a..5ab0b9edfc88 100644 --- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi +++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi @@ -72,13 +72,13 @@ sound { compatible = "audio-graph-card"; - label = "rockchip,rk3399"; + label = "Analog"; dais = <&i2s1_p0>; }; sound-dit { compatible = "audio-graph-card"; - label = "rockchip,rk3399"; + label = "SPDIF"; dais = <&spdif_p0>; }; From e9cb878ec238f85b81c7b439b4280062d4fbf9b8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Mon, 1 Feb 2021 10:13:08 +0100 Subject: [PATCH 492/584] ARM: dts: ux500: Add Flash LEDs to Samsung phones This adds the Richtek RT8515 Flash LED to the Golden, Skomer and Janice device trees. Signed-off-by: Linus Walleij Link: https://lore.kernel.org/r/20210201091308.284465-1-linus.walleij@linaro.org' Signed-off-by: Arnd Bergmann --- .../arm/boot/dts/ste-ux500-samsung-golden.dts | 36 +++++++++++++++++++ .../arm/boot/dts/ste-ux500-samsung-janice.dts | 36 +++++++++++++++++++ .../arm/boot/dts/ste-ux500-samsung-skomer.dts | 35 ++++++++++++++++++ 3 files changed, 107 insertions(+) diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts index 00ee013cbd1d..7010fdcd76b2 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts @@ -5,6 +5,7 @@ #include "ste-ab8505.dtsi" #include "ste-dbx5x0-pinctrl.dtsi" #include +#include #include #include @@ -373,6 +374,32 @@ }; }; + /* Richtek RT8515GQW Flash LED Driver IC */ + flash { + compatible = "richtek,rt8515"; + /* GPIO 140 */ + enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; + /* GPIO 141 */ + ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; + /* + * RFS is 16 kOhm and RTS is 100 kOhm giving + * the flash max current 343mA and torch max + * current 55 mA. + */ + richtek,rfs-ohms = <16000>; + richtek,rts-ohms = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_flash_default_mode>; + + led { + function = LED_FUNCTION_FLASH; + color = ; + flash-max-timeout-us = <250000>; + flash-max-microamp = <343750>; + led-max-microamp = <55000>; + }; + }; + vibrator { compatible = "gpio-vibrator"; /* GPIO195 (MOT_EN) */ @@ -498,6 +525,15 @@ }; }; + flash { + gpio_flash_default_mode: flash_default { + golden_cfg1 { + pins = "GPIO140_B11", "GPIO141_C12"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + i2c-gpio-1 { i2c_gpio_1_default: i2c_gpio_1 { golden_cfg1 { diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts index 95d5abe5dc0d..7411bfeda285 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts @@ -8,6 +8,7 @@ #include "ste-ab8500.dtsi" #include "ste-dbx5x0-pinctrl.dtsi" #include +#include #include #include @@ -180,6 +181,32 @@ }; }; + /* Richtek RT8515GQW Flash LED Driver IC */ + flash { + compatible = "richtek,rt8515"; + /* GPIO 140 */ + enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; + /* GPIO 141 */ + ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; + /* + * RFS is 16 kOhm and RTS is 100 kOhm giving + * the flash max current 343mA and torch max + * current 55 mA. + */ + richtek,rfs-ohms = <16000>; + richtek,rts-ohms = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_flash_default_mode>; + + led { + function = LED_FUNCTION_FLASH; + color = ; + flash-max-timeout-us = <250000>; + flash-max-microamp = <343750>; + led-max-microamp = <55000>; + }; + }; + /* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */ i2c-gpio-0 { compatible = "i2c-gpio"; @@ -739,6 +766,15 @@ }; }; }; + /* Flash and torch */ + flash { + gpio_flash_default_mode: flash_default { + janice_cfg1 { + pins = "GPIO140_B11", "GPIO141_C12"; + ste,config = <&gpio_out_lo>; + }; + }; + }; /* GPIO keys */ gpio-keys { gpio_keys_default_mode: gpio_keys_default { diff --git a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts index 36420492fd72..d28a00757d0b 100644 --- a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts +++ b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts @@ -8,6 +8,7 @@ #include "ste-ab8505.dtsi" #include "ste-dbx5x0-pinctrl.dtsi" #include +#include #include #include @@ -118,6 +119,32 @@ pinctrl-0 = <&gpio_backlight_default_mode>; }; + /* Richtek RT8515GQW Flash LED Driver IC */ + flash { + compatible = "richtek,rt8515"; + /* GPIO 140 */ + enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>; + /* GPIO 141 */ + ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>; + /* + * RFS is 16 kOhm and RTS is 100 kOhm giving + * the flash max current 343mA and torch max + * current 55 mA. + */ + richtek,rfs-ohms = <16000>; + richtek,rts-ohms = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_flash_default_mode>; + + led { + function = LED_FUNCTION_FLASH; + color = ; + flash-max-timeout-us = <250000>; + flash-max-microamp = <343750>; + led-max-microamp = <55000>; + }; + }; + i2c-gpio-0 { compatible = "i2c-gpio"; sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; @@ -487,6 +514,14 @@ }; }; }; + flash { + gpio_flash_default_mode: flash_default { + skomer_cfg1 { + pins = "GPIO140_B11", "GPIO141_C12"; + ste,config = <&gpio_out_lo>; + }; + }; + }; /* GPIO that enables the 2.9V SD card level translator */ sd-level-translator { sd_level_translator_default: sd_level_translator_default { From 1adacc4919099bc115efb61a6db89c7f663c90e0 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:19 +0100 Subject: [PATCH 493/584] dt-bindings: gpio: mrvl-gpio: Fix the gpio-ranges property The property specifies a list of GPIO-capable pins. Don't limit it to a single element as there's presumably more than one GPIO pin. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-2-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml b/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml index 4db3b8a3332c..9cf6137dd524 100644 --- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml +++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml @@ -82,8 +82,7 @@ properties: '#gpio-cells': const: 2 - gpio-ranges: - maxItems: 1 + gpio-ranges: true interrupts: true From fa432444095a35cfffdea87688d6e33db9cc9aff Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:20 +0100 Subject: [PATCH 494/584] media: dt-bindings: marvell,mmp2-ccic: Allow power-domains property On MMP3 the camera interface is on a separate power island. This property tells the driver to enable it when appropriate. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-3-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- .../devicetree/bindings/media/marvell,mmp2-ccic.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml index 49bff738aca5..52eab686a177 100644 --- a/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml +++ b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml @@ -23,6 +23,9 @@ properties: interrupts: maxItems: 1 + power-domains: + maxItems: 1 + port: type: object additionalProperties: false @@ -75,6 +78,7 @@ additionalProperties: false examples: - | #include + #include camera@d420a000 { compatible = "marvell,mmp2-ccic"; @@ -84,6 +88,7 @@ examples: clock-names = "axi"; #clock-cells = <0>; clock-output-names = "mclk"; + power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>; port { camera0_0: endpoint { From 7ca1ea0db2de82e72eb6b440c09019045821bc68 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:21 +0100 Subject: [PATCH 495/584] ARM: dts: mmp2-olpc-xo-1-75: Fix memory node name It contains a reg property. Add its base to the node name. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-4-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts index 342304f5653a..e16171ddd93e 100644 --- a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts +++ b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts @@ -32,7 +32,7 @@ }; }; - memory { + memory@0 { linux,usable-memory = <0x0 0x1f800000>; available = <0xcf000 0x1ef31000 0x1000 0xbf000>; reg = <0x0 0x20000000>; From ebfdb34c277dd9407d52e69f26bd4d92efed25d3 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:22 +0100 Subject: [PATCH 496/584] ARM: dts: mmp2-olpc-xo-1-75: Drop linux,usable-memory from /memory Drop the linux,usable-memory properties; the schema is unhappy about them: mmp2-olpc-xo-1-75.dt.yaml: /: memory: False schema does not allow {'linux,usable-memory': [[0, 528482304]], 'available': [[847872, 519245824, 4096, 782336]], 'reg': [[0, 536870912]], 'device_type': ['memory']} They've been cargo-culted from Open Firmware and I don't know what purpose they serve. Perhaps they are meant to provide the OFW runtime. In that case it's still okay to drop them from here; OFW is welcome to add it upon boot. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-5-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts index e16171ddd93e..0f8b5ad48dee 100644 --- a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts +++ b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts @@ -33,7 +33,6 @@ }; memory@0 { - linux,usable-memory = <0x0 0x1f800000>; available = <0xcf000 0x1ef31000 0x1000 0xbf000>; reg = <0x0 0x20000000>; device_type = "memory"; From 1130466a4101bf16f7065de87d3e0a4ac233eda7 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:23 +0100 Subject: [PATCH 497/584] ARM: dts: mmp3-dell-ariel: Drop linux,usable-memory from /memory Drop the linux,usable-memory properties; the schema is unhappy about them. They've been cargo-culted from Open Firmware and I don't know what purpose they serve. Perhaps they are meant to provide the OFW runtime. In that case it's still okay to drop them from here; OFW is welcome to add it upon boot. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-6-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp3-dell-ariel.dts | 1 - 1 file changed, 1 deletion(-) diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/mmp3-dell-ariel.dts index fe3b1cd695ee..53714cb0d171 100644 --- a/arch/arm/boot/dts/mmp3-dell-ariel.dts +++ b/arch/arm/boot/dts/mmp3-dell-ariel.dts @@ -26,7 +26,6 @@ }; memory@0 { - linux,usable-memory = <0x0 0x7f600000>; available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>; reg = <0x0 0x80000000>; device_type = "memory"; From 5fb4df28da3b7a4d88e4d0650b151ea359c047fa Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:24 +0100 Subject: [PATCH 498/584] ARM: dts: mmp3: Extend the MPMU reg range The ACGR register is at the offset of 0x1024, beyond the 4k originally assigned to the MPMU range. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-7-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp3.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/mmp3.dtsi b/arch/arm/boot/dts/mmp3.dtsi index 4ae630d37d09..9f2b059f0900 100644 --- a/arch/arm/boot/dts/mmp3.dtsi +++ b/arch/arm/boot/dts/mmp3.dtsi @@ -567,7 +567,7 @@ soc_clocks: clocks@d4050000 { compatible = "marvell,mmp3-clock"; - reg = <0xd4050000 0x1000>, + reg = <0xd4050000 0x2000>, <0xd4282800 0x400>, <0xd4015000 0x1000>; reg-names = "mpmu", "apmu", "apbc"; From d2192c0d3cfb949b5a570f6494672fdc2a9b22c0 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:25 +0100 Subject: [PATCH 499/584] ARM: dts: mmp2: Use symbolic names for audio clocks These are slighly easier to read. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-8-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp2.dtsi | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/mmp2.dtsi index 445bdcd50b9e..46984d4c5224 100644 --- a/arch/arm/boot/dts/mmp2.dtsi +++ b/arch/arm/boot/dts/mmp2.dtsi @@ -6,6 +6,7 @@ #include #include +#include / { #address-cells = <1>; @@ -243,7 +244,7 @@ interrupts = <2>; clock-names = "audio", "bitclk"; clocks = <&soc_clocks MMP2_CLK_AUDIO>, - <&audio_clk 1>; + <&audio_clk MMP2_CLK_AUDIO_SSPA0>; power-domains = <&soc_clocks MMP2_POWER_DOMAIN_AUDIO>; #sound-dai-cells = <0>; status = "disabled"; @@ -256,7 +257,7 @@ interrupts = <3>; clock-names = "audio", "bitclk"; clocks = <&soc_clocks MMP2_CLK_AUDIO>, - <&audio_clk 2>; + <&audio_clk MMP2_CLK_AUDIO_SSPA1>; power-domains = <&soc_clocks MMP2_POWER_DOMAIN_AUDIO>; #sound-dai-cells = <0>; status = "disabled"; From a2decdbd7592a88b99101e2d926cefc774528869 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:26 +0100 Subject: [PATCH 500/584] ARM: dts: mmp2-olpc-xo-1-75: Use symbolic names for audio clocks These are slighly easier to read. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-9-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts index 0f8b5ad48dee..55ea87870af3 100644 --- a/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts +++ b/arch/arm/boot/dts/mmp2-olpc-xo-1-75.dts @@ -2,7 +2,7 @@ /* * OLPC XO 1.75 Laptop. * - * Copyright (C) 2018,2019 Lubomir Rintel + * Copyright (C) 2018,2019,2020 Lubomir Rintel */ /dts-v1/; @@ -10,6 +10,7 @@ #include #include #include +#include / { model = "OLPC XO-1.75"; @@ -194,7 +195,7 @@ port { rt5631_0: endpoint { mclk-fs = <256>; - clocks = <&audio_clk 0>; + clocks = <&audio_clk MMP2_CLK_AUDIO_SYSCLK>; remote-endpoint = <&sspa0_0>; }; }; From e691d58e3383a09e2171a6dfbb1f5b368a2ce2f3 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:27 +0100 Subject: [PATCH 501/584] ARM: dts: mmp3-dell-ariel: Add the embedded controller Add the device node for the computer's embedded controller, responsible for controlling the LEDs and system power. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-10-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp3-dell-ariel.dts | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/mmp3-dell-ariel.dts index 53714cb0d171..565cd0fadf3d 100644 --- a/arch/arm/boot/dts/mmp3-dell-ariel.dts +++ b/arch/arm/boot/dts/mmp3-dell-ariel.dts @@ -95,6 +95,15 @@ &twsi4 { status = "okay"; + + embedded-controller@58 { + compatible = "dell,wyse-ariel-ec", "ene,kb3930"; + reg = <0x58>; + system-power-controller; + + off-gpios = <&gpio 126 GPIO_ACTIVE_HIGH>, + <&gpio 127 GPIO_ACTIVE_HIGH>; + }; }; &ssp1 { From 49061130eb1f654065b25903d57dad41519ee6c9 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:28 +0100 Subject: [PATCH 502/584] ARM: dts: mmp3-dell-ariel: Add the power button node This adds support for the power button attached to the Embedded Controller on a Dell Wyse 3020 "Ariel" board. However, while the EC itself is controlled via I2C, the input capability for the power button acts as a separate device attached to the SPI, hence it has a separate device node. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-11-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp3-dell-ariel.dts | 10 +++++++++- 1 file changed, 9 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/mmp3-dell-ariel.dts index 565cd0fadf3d..c4a6bd876d84 100644 --- a/arch/arm/boot/dts/mmp3-dell-ariel.dts +++ b/arch/arm/boot/dts/mmp3-dell-ariel.dts @@ -119,8 +119,16 @@ }; &ssp2 { - cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>; status = "okay"; + cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>; + + power-button@0 { + reg = <0>; + interrupt-parent = <&gpio>; + interrupts = <60 IRQ_TYPE_EDGE_RISING>; + compatible = "dell,wyse-ariel-ec-input", "ene,kb3930-input"; + spi-max-frequency = <33000000>; + }; }; &gpu_2d { From 0561cba77cafdbfa966eeb87163d2e874e3669e5 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:29 +0100 Subject: [PATCH 503/584] ARM: dts: mmp3-dell-ariel: Replace SSP2 with spi-gpio The firmware leaves the pins in GPIO mode. Until we have a proper pinmux driver hooked on we just need to bitbang SPI. No big deal, this is just used for the power button and performance is not important. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-12-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp3-dell-ariel.dts | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/mmp3-dell-ariel.dts index c4a6bd876d84..fe6df364a9eb 100644 --- a/arch/arm/boot/dts/mmp3-dell-ariel.dts +++ b/arch/arm/boot/dts/mmp3-dell-ariel.dts @@ -30,6 +30,17 @@ reg = <0x0 0x80000000>; device_type = "memory"; }; + + ec_input_spi: spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + num-chipselects = <0>; + sck-gpios = <&gpio 55 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio 57 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio 58 GPIO_ACTIVE_HIGH>; + }; }; &uart3 { @@ -118,7 +129,7 @@ }; }; -&ssp2 { +&ec_input_spi { status = "okay"; cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>; From fff342100771e30e0bc4c7ad68a9f237f549a2e4 Mon Sep 17 00:00:00 2001 From: Lubomir Rintel Date: Thu, 21 Jan 2021 04:41:30 +0100 Subject: [PATCH 504/584] ARM: dts: mmp3: Fix the CCIC interrupts A copy & paste oversight from MMP2; camera interrupts are handled via a multiplexer on MMP3. Signed-off-by: Lubomir Rintel Link: https://lore.kernel.org/r/20210121034130.1381872-13-lkundrak@v3.sk' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/mmp3.dtsi | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/mmp3.dtsi b/arch/arm/boot/dts/mmp3.dtsi index 9f2b059f0900..a4fb9203ec1f 100644 --- a/arch/arm/boot/dts/mmp3.dtsi +++ b/arch/arm/boot/dts/mmp3.dtsi @@ -293,7 +293,8 @@ camera0: camera@d420a000 { compatible = "marvell,mmp2-ccic"; reg = <0xd420a000 0x800>; - interrupts = ; + interrupts = <1>; + interrupt-parent = <&ci_mux>; clocks = <&soc_clocks MMP2_CLK_CCIC0>; clock-names = "axi"; power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>; @@ -305,7 +306,8 @@ camera1: camera@d420a800 { compatible = "marvell,mmp2-ccic"; reg = <0xd420a800 0x800>; - interrupts = ; + interrupts = <2>; + interrupt-parent = <&ci_mux>; clocks = <&soc_clocks MMP2_CLK_CCIC1>; clock-names = "axi"; power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>; From bd67534d18b4a1ca8755f59702d4acf5a9ba7b1a Mon Sep 17 00:00:00 2001 From: Vincent Knecht Date: Sat, 30 Jan 2021 11:57:10 +0100 Subject: [PATCH 505/584] dt-bindings: vendor-prefixes: add Alcatel Document vendor prefix for Alcatel Signed-off-by: Vincent Knecht Link: https://lore.kernel.org/r/20210130105717.2628781-2-vincent.knecht@mailoo.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 041ae90b0d8f..08150a1217e9 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -59,6 +59,8 @@ patternProperties: description: Aeroflex Gaisler AB "^al,.*": description: Annapurna Labs + "^alcatel,.*": + description: Alcatel "^allegro,.*": description: Allegro DVT "^allo,.*": From b32155ff0256dbc053874e61f532a75fdfb5ec31 Mon Sep 17 00:00:00 2001 From: Vincent Knecht Date: Sat, 30 Jan 2021 11:57:11 +0100 Subject: [PATCH 506/584] arm64: dts: qcom: Add device tree for Alcatel Idol 3 (4.7") The Alcatel Idol 3 (4.7") is a smartphone based on MSM8916. Add a device tree with support for USB, eMMC, SD-Card, WiFi, BT, power/volume buttons, vibrator and the following sensors: magnetometer, accelerometer, gyroscope, ambient light+proximity Reviewed-by: Stephan Gerhold Reviewed-by: Konrad Dybcio Signed-off-by: Vincent Knecht Link: https://lore.kernel.org/r/20210130105717.2628781-3-vincent.knecht@mailoo.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8916-alcatel-idol347.dts | 291 ++++++++++++++++++ 2 files changed, 292 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 59455db7b493..0feeedb712cc 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8096-db820c.dtb dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq6018-cp01-c1.dtb dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts new file mode 100644 index 000000000000..540b1fa4b260 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts @@ -0,0 +1,291 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include +#include + +/ { + model = "Alcatel OneTouch Idol 3 (4.7)"; + compatible = "alcatel,idol347", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 69 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&blsp_i2c5 { + status = "okay"; + + magnetometer@c { + compatible = "asahi-kasei,ak09911"; + reg = <0x0c>; + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + reset-gpios = <&msmgpio 8 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; + + accelerometer@f { + compatible = "kionix,kxtj21009"; + reg = <0x0f>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + interrupt-parent = <&msmgpio>; + interrupts = <31 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&accel_int_default>; + mount-matrix = "-1", "0", "0", + "0", "1", "0", + "0", "0", "-1"; + }; + + proximity@48 { + compatible = "sensortek,stk3310"; + reg = <0x48>; + interrupt-parent = <&msmgpio>; + interrupts = <12 IRQ_TYPE_EDGE_FALLING>; + pinctrl-names = "default"; + pinctrl-0 = <&proximity_int_default>; + }; + + gyroscope@68 { + compatible = "bosch,bmg160"; + reg = <0x68>; + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + interrupt-parent = <&msmgpio>; + interrupts = <97 IRQ_TYPE_EDGE_RISING>, + <98 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&gyro_int_default>; + }; +}; + +&pm8916_resin { + status = "okay"; + linux,code = ; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + accel_int_default: accel-int-default { + pins = "gpio31"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + gyro_int_default: gyro-int-default { + pins = "gpio97", "gpio98"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + mag_reset_default: mag-reset-default { + pins = "gpio8"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + proximity_int_default: proximity-int-default { + pins = "gpio12"; + function = "gpio"; + + drive-strength = <6>; + bias-pull-up; + }; + + usb_id_default: usb-id-default { + pins = "gpio69"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; From 5f36d633c214bc21eaa7590d96e6a425261ccd57 Mon Sep 17 00:00:00 2001 From: Vincent Knecht Date: Sat, 30 Jan 2021 11:57:12 +0100 Subject: [PATCH 507/584] arm64: dts: qcom: Disable MDSS by default for 8916/8016 devices Disable MDSS (Mobile Display Subsystem) by default in msm8916.dtsi and only explicitly enable it in devices' DT which actually use it. This leads to faster boot and cleaner logs for other devices, which also won't have to explicitly disable MDSS to use framebuffer. Reviewed-by: Stephan Gerhold Reviewed-by: Konrad Dybcio Signed-off-by: Vincent Knecht Link: https://lore.kernel.org/r/20210130105717.2628781-4-vincent.knecht@mailoo.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi | 4 ++++ arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi | 4 ++++ arch/arm64/boot/dts/qcom/msm8916.dtsi | 1 + 3 files changed, 9 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi index 3a9538e1ec97..6aef0c2e4f0a 100644 --- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi +++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi @@ -301,6 +301,10 @@ status = "okay"; }; +&mdss { + status = "okay"; +}; + &pm8916_resin { status = "okay"; linux,code = ; diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi index f1af798abd74..230ba3ce3277 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi @@ -132,6 +132,10 @@ pinctrl-1 = <&mdss_sleep>; }; +&mdss { + status = "okay"; +}; + &pm8916_resin { status = "okay"; linux,code = ; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 402e891a84ab..8f9a651d3827 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -913,6 +913,7 @@ }; mdss: mdss@1a00000 { + status = "disabled"; compatible = "qcom,mdss"; reg = <0x01a00000 0x1000>, <0x01ac8000 0x3000>; From 2c1b8ebe929f1d452c95f8a4d32e3a265eb5b2c2 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 27 Jan 2021 18:00:49 +0530 Subject: [PATCH 508/584] dt-bindings: arm: qcom: Document SM8350 SoC and boards Document the SM8350 SoC binding and also the boards using it. Reviewed-by: Bjorn Andersson Acked-by: Rob Herring Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20210127123054.263231-2-vkoul@kernel.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml index c97d4a580f47..8fe7e473bfdf 100644 --- a/Documentation/devicetree/bindings/arm/qcom.yaml +++ b/Documentation/devicetree/bindings/arm/qcom.yaml @@ -41,6 +41,7 @@ description: | sdm660 sdm845 sm8250 + sm8350 The 'board' element must be one of the following strings: @@ -178,6 +179,11 @@ properties: - qcom,sm8250-mtp - const: qcom,sm8250 + - items: + - enum: + - qcom,sm8350-mtp + - const: qcom,sm8350 + additionalProperties: true ... From 8767fe36d90e3433bd18eb0f84d852da73d5c8c6 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 27 Jan 2021 18:00:51 +0530 Subject: [PATCH 509/584] dt-bindings: arm: cpus: Add kryo685 compatible Kryo685 is found in SM8350, so add it to the list of cpu compatibles Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20210127123054.263231-4-vkoul@kernel.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/arm/cpus.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/cpus.yaml b/Documentation/devicetree/bindings/arm/cpus.yaml index 14cd727d3c4b..3a0b4c54cd8e 100644 --- a/Documentation/devicetree/bindings/arm/cpus.yaml +++ b/Documentation/devicetree/bindings/arm/cpus.yaml @@ -169,6 +169,7 @@ properties: - qcom,kryo385 - qcom,kryo468 - qcom,kryo485 + - qcom,kryo685 - qcom,scorpion enable-method: From 80ad7f3349e63a12b9b9ba767884a513df362ec2 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 27 Jan 2021 18:00:52 +0530 Subject: [PATCH 510/584] dt-bindings: firmware: scm: Add SM8250 and SM8350 compatible Add compatible for SM8150 and SM8350 SoCs. Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20210127123054.263231-5-vkoul@kernel.org Signed-off-by: Bjorn Andersson --- Documentation/devicetree/bindings/firmware/qcom,scm.txt | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/firmware/qcom,scm.txt b/Documentation/devicetree/bindings/firmware/qcom,scm.txt index 78456437df5f..a884955f861e 100644 --- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt +++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt @@ -22,6 +22,8 @@ Required properties: * "qcom,scm-sc7180" * "qcom,scm-sdm845" * "qcom,scm-sm8150" + * "qcom,scm-sm8250" + * "qcom,scm-sm8350" and: * "qcom,scm" - clocks: Specifies clocks needed by the SCM interface, if any: From b7e8f433a673eb875007111a75e9dbdc61ea5c14 Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 27 Jan 2021 18:00:53 +0530 Subject: [PATCH 511/584] arm64: dts: qcom: Add basic devicetree support for SM8350 SoC Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC. This adds gcc, pinctrl, reserved memory, uart, cpu nodes for this SoC. Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20210127123054.263231-6-vkoul@kernel.org [bjorn: Adjusted 4th timer interrupt, per input from Sai] Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8350.dtsi | 499 +++++++++++++++++++++++++++ 1 file changed, 499 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8350.dtsi diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi new file mode 100644 index 000000000000..5ef460458f5c --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi @@ -0,0 +1,499 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Linaro Limaited + */ + +#include +#include +#include +#include +#include +#include + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <38400000>; + clock-output-names = "xo_board"; + }; + + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + clock-frequency = <32000>; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <2>; + #size-cells = <0>; + + CPU0: cpu@0 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x0>; + enable-method = "psci"; + next-level-cache = <&L2_0>; + L2_0: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + L3_0: l3-cache { + compatible = "cache"; + }; + }; + }; + + CPU1: cpu@100 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x100>; + enable-method = "psci"; + next-level-cache = <&L2_100>; + L2_100: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU2: cpu@200 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x200>; + enable-method = "psci"; + next-level-cache = <&L2_200>; + L2_200: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU3: cpu@300 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x300>; + enable-method = "psci"; + next-level-cache = <&L2_300>; + L2_300: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU4: cpu@400 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x400>; + enable-method = "psci"; + next-level-cache = <&L2_400>; + L2_400: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU5: cpu@500 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x500>; + enable-method = "psci"; + next-level-cache = <&L2_500>; + L2_500: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + + }; + + CPU6: cpu@600 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x600>; + enable-method = "psci"; + next-level-cache = <&L2_600>; + L2_600: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + + CPU7: cpu@700 { + device_type = "cpu"; + compatible = "qcom,kryo685"; + reg = <0x0 0x700>; + enable-method = "psci"; + next-level-cache = <&L2_700>; + L2_700: l2-cache { + compatible = "cache"; + next-level-cache = <&L3_0>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-sm8350", "qcom,scm"; + #reset-cells = <1>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the size */ + reg = <0x0 0x80000000 0x0 0x0>; + }; + + pmu { + compatible = "arm,armv8-pmuv3"; + interrupts = ; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + }; + + reserved_memory: reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + hyp_mem: memory@80000000 { + reg = <0x0 0x80000000 0x0 0x600000>; + no-map; + }; + + xbl_aop_mem: memory@80700000 { + no-map; + reg = <0x0 0x80700000 0x0 0x160000>; + }; + + cmd_db: memory@80860000 { + compatible = "qcom,cmd-db"; + reg = <0x0 0x80860000 0x0 0x20000>; + no-map; + }; + + reserved_xbl_uefi_log: memory@80880000 { + reg = <0x0 0x80880000 0x0 0x14000>; + no-map; + }; + + smem_mem: memory@80900000 { + reg = <0x0 0x80900000 0x0 0x200000>; + no-map; + }; + + cpucp_fw_mem: memory@80b00000 { + reg = <0x0 0x80b00000 0x0 0x100000>; + no-map; + }; + + cdsp_secure_heap: memory@80c00000 { + reg = <0x0 0x80c00000 0x0 0x4600000>; + no-map; + }; + + pil_camera_mem: mmeory@85200000 { + reg = <0x0 0x85200000 0x0 0x500000>; + no-map; + }; + + pil_video_mem: memory@85700000 { + reg = <0x0 0x85700000 0x0 0x500000>; + no-map; + }; + + pil_cvp_mem: memory@85c00000 { + reg = <0x0 0x85c00000 0x0 0x500000>; + no-map; + }; + + pil_adsp_mem: memory@86100000 { + reg = <0x0 0x86100000 0x0 0x2100000>; + no-map; + }; + + pil_slpi_mem: memory@88200000 { + reg = <0x0 0x88200000 0x0 0x1500000>; + no-map; + }; + + pil_cdsp_mem: memory@89700000 { + reg = <0x0 0x89700000 0x0 0x1e00000>; + no-map; + }; + + pil_ipa_fw_mem: memory@8b500000 { + reg = <0x0 0x8b500000 0x0 0x10000>; + no-map; + }; + + pil_ipa_gsi_mem: memory@8b510000 { + reg = <0x0 0x8b510000 0x0 0xa000>; + no-map; + }; + + pil_gpu_mem: memory@8b51a000 { + reg = <0x0 0x8b51a000 0x0 0x2000>; + no-map; + }; + + pil_spss_mem: memory@8b600000 { + reg = <0x0 0x8b600000 0x0 0x100000>; + no-map; + }; + + pil_modem_mem: memory@8b800000 { + reg = <0x0 0x8b800000 0x0 0x10000000>; + no-map; + }; + + hyp_reserved_mem: memory@d0000000 { + reg = <0x0 0xd0000000 0x0 0x800000>; + no-map; + }; + + pil_trustedvm_mem: memory@d0800000 { + reg = <0x0 0xd0800000 0x0 0x76f7000>; + no-map; + }; + + qrtr_shbuf: memory@d7ef7000 { + reg = <0x0 0xd7ef7000 0x0 0x9000>; + no-map; + }; + + chan0_shbuf: memory@d7f00000 { + reg = <0x0 0xd7f00000 0x0 0x80000>; + no-map; + }; + + chan1_shbuf: memory@d7f80000 { + reg = <0x0 0xd7f80000 0x0 0x80000>; + no-map; + }; + + removed_mem: memory@d8800000 { + reg = <0x0 0xd8800000 0x0 0x6800000>; + no-map; + }; + }; + + smem: qcom,smem { + compatible = "qcom,smem"; + memory-region = <&smem_mem>; + hwlocks = <&tcsr_mutex 3>; + }; + + soc: soc@0 { + #address-cells = <2>; + #size-cells = <2>; + ranges = <0 0 0 0 0x10 0>; + dma-ranges = <0 0 0 0 0x10 0>; + compatible = "simple-bus"; + + gcc: clock-controller@100000 { + compatible = "qcom,gcc-sm8350"; + reg = <0x0 0x00100000 0x0 0x1f0000>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + clock-names = "bi_tcxo", "sleep_clk"; + clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; + }; + + ipcc: mailbox@408000 { + compatible = "qcom,sm8350-ipcc", "qcom,ipcc"; + reg = <0 0x00408000 0 0x1000>; + interrupts = ; + interrupt-controller; + #interrupt-cells = <3>; + #mbox-cells = <2>; + }; + + qupv3_id_1: geniqup@9c0000 { + compatible = "qcom,geni-se-qup"; + reg = <0x0 0x009c0000 0x0 0x6000>; + clock-names = "m-ahb", "s-ahb"; + clocks = <&gcc 121>, + <&gcc 122>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "disabled"; + + uart2: serial@98c000 { + compatible = "qcom,geni-debug-uart"; + reg = <0 0x0098c000 0 0x4000>; + clock-names = "se"; + clocks = <&gcc 83>; + pinctrl-names = "default"; + pinctrl-0 = <&qup_uart3_default_state>; + interrupts = ; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + }; + + tcsr_mutex: hwlock@1f40000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x0 0x01f40000 0x0 0x40000>; + #hwlock-cells = <1>; + }; + + pdc: interrupt-controller@b220000 { + compatible = "qcom,sm8350-pdc", "qcom,pdc"; + reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>; + qcom,pdc-ranges = <0 480 40>, <40 140 14>, <54 263 1>, <55 306 4>, + <59 312 3>, <62 374 2>, <64 434 2>, <66 438 3>, + <69 86 1>, <70 520 54>, <124 609 31>, <155 63 1>, + <156 716 12>; + #interrupt-cells = <2>; + interrupt-parent = <&intc>; + interrupt-controller; + }; + + aoss_qmp: qmp@c300000 { + compatible = "qcom,sm8350-aoss-qmp"; + reg = <0 0x0c300000 0 0x100000>; + interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP + IRQ_TYPE_EDGE_RISING>; + mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>; + + #clock-cells = <0>; + #power-domain-cells = <1>; + }; + + tlmm: pinctrl@f100000 { + compatible = "qcom,sm8350-tlmm"; + reg = <0 0x0f100000 0 0x300000>; + interrupts = ; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 203>; + + qup_uart3_default_state: qup-uart3-default-state { + rx { + pins = "gpio18"; + function = "qup3"; + }; + tx { + pins = "gpio19"; + function = "qup3"; + }; + }; + }; + + intc: interrupt-controller@17a00000 { + compatible = "arm,gic-v3"; + #interrupt-cells = <3>; + interrupt-controller; + reg = <0x0 0x17a00000 0x0 0x10000>, /* GICD */ + <0x0 0x17a60000 0x0 0x100000>; /* GICR * 8 */ + interrupts = ; + }; + + timer@17c20000 { + compatible = "arm,armv7-timer-mem"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + reg = <0x0 0x17c20000 0x0 0x1000>; + clock-frequency = <19200000>; + + frame@17c21000 { + frame-number = <0>; + interrupts = , + ; + reg = <0x0 0x17c21000 0x0 0x1000>, + <0x0 0x17c22000 0x0 0x1000>; + }; + + frame@17c23000 { + frame-number = <1>; + interrupts = ; + reg = <0x0 0x17c23000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c25000 { + frame-number = <2>; + interrupts = ; + reg = <0x0 0x17c25000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c27000 { + frame-number = <3>; + interrupts = ; + reg = <0x0 0x17c27000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c29000 { + frame-number = <4>; + interrupts = ; + reg = <0x0 0x17c29000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2b000 { + frame-number = <5>; + interrupts = ; + reg = <0x0 0x17c2b000 0x0 0x1000>; + status = "disabled"; + }; + + frame@17c2d000 { + frame-number = <6>; + interrupts = ; + reg = <0x0 0x17c2d000 0x0 0x1000>; + status = "disabled"; + }; + }; + + apps_rsc: rsc@18200000 { + label = "apps_rsc"; + compatible = "qcom,rpmh-rsc"; + reg = <0x0 0x18200000 0x0 0x10000>, + <0x0 0x18210000 0x0 0x10000>, + <0x0 0x18220000 0x0 0x10000>; + reg-names = "drv-0", "drv-1", "drv-2"; + interrupts = , + , + ; + qcom,tcs-offset = <0xd00>; + qcom,drv-id = <2>; + qcom,tcs-config = , , + , ; + + rpmhcc: clock-controller { + compatible = "qcom,sm8350-rpmh-clk"; + #clock-cells = <1>; + clock-names = "xo"; + clocks = <&xo_board>; + }; + + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = , + , + , + ; + }; +}; From 0684074a46e8ef939c7afe6b9c7381563599c33a Mon Sep 17 00:00:00 2001 From: Vinod Koul Date: Wed, 27 Jan 2021 18:00:54 +0530 Subject: [PATCH 512/584] arm64: dts: qcom: Add basic devicetree support for SM8350-MTP board Add basic devicetree support for Qualcomm Technologies, Inc SM8350 SoC MTP board. This enabled uart node and adds rpmh-regulators present for this board. Signed-off-by: Vinod Koul Link: https://lore.kernel.org/r/20210127123054.263231-7-vkoul@kernel.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/sm8350-mtp.dts | 250 ++++++++++++++++++++++++ 2 files changed, 251 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sm8350-mtp.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 0feeedb712cc..ac9a1b61aab1 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -58,3 +58,4 @@ dtb-$(CONFIG_ARCH_QCOM) += sm8150-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8150-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-hdk.dtb dtb-$(CONFIG_ARCH_QCOM) += sm8250-mtp.dtb +dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb diff --git a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts new file mode 100644 index 000000000000..8923657579fb --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Linaro Limited + */ + +/dts-v1/; + +#include +#include "sm8350.dtsi" + +/ { + model = "Qualcomm Technologies, Inc. sm8350 MTP"; + compatible = "qcom,sm8350-mtp", "qcom,sm8350"; + + aliases { + serial0 = &uart2; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + vph_pwr: vph-pwr-regulator { + compatible = "regulator-fixed"; + regulator-name = "vph_pwr"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + + regulator-always-on; + regulator-boot-on; + }; +}; + +&apps_rsc { + pm8350-rpmh-regulators { + compatible = "qcom,pm8350-rpmh-regulators"; + qcom,pmic-id = "b"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + vdd-s11-supply = <&vph_pwr>; + vdd-s12-supply = <&vph_pwr>; + + vdd-l1-l4-supply = <&vreg_s11b_0p95>; + vdd-l2-l7-supply = <&vreg_bob>; + vdd-l3-l5-supply = <&vreg_bob>; + vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>; + vdd-l8-supply = <&vreg_s2c_0p8>; + + vreg_s10b_1p8: smps10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_s11b_0p95: smps11 { + regulator-min-microvolt = <752000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_s12b_1p25: smps12 { + regulator-min-microvolt = <1224000>; + regulator-max-microvolt = <1360000>; + }; + + vreg_l1b_0p88: ldo1 { + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <920000>; + regulator-initial-mode = ; + }; + + vreg_l2b_3p07: ldo2 { + regulator-min-microvolt = <3072000>; + regulator-max-microvolt = <3072000>; + regulator-initial-mode = ; + }; + + vreg_l3b_0p9: ldo3 { + regulator-min-microvolt = <904000>; + regulator-max-microvolt = <904000>; + regulator-initial-mode = ; + }; + + vreg_l5b_0p88: ldo5 { + regulator-min-microvolt = <880000>; + regulator-max-microvolt = <888000>; + regulator-initial-mode = ; + }; + + vreg_l6b_1p2: ldo6 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1208000>; + regulator-initial-mode = ; + }; + + vreg_l7b_2p96: ldo7 { + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = ; + }; + + vreg_l9b_1p2: ldo9 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + }; + + pm8350c-rpmh-regulators { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vdd-s1-supply = <&vph_pwr>; + vdd-s2-supply = <&vph_pwr>; + vdd-s3-supply = <&vph_pwr>; + vdd-s4-supply = <&vph_pwr>; + vdd-s5-supply = <&vph_pwr>; + vdd-s6-supply = <&vph_pwr>; + vdd-s7-supply = <&vph_pwr>; + vdd-s8-supply = <&vph_pwr>; + vdd-s9-supply = <&vph_pwr>; + vdd-s10-supply = <&vph_pwr>; + + vdd-l1-l12-supply = <&vreg_s1c_1p86>; + vdd-l2-l8-supply = <&vreg_s1c_1p86>; + vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>; + vdd-l6-l9-l11-supply = <&vreg_bob>; + vdd-l10-supply = <&vreg_s12b_1p25>; + + vdd-bob-supply = <&vph_pwr>; + + vreg_s1c_1p86: smps1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1952000>; + }; + + vreg_s2c_0p8: smps2 { + regulator-min-microvolt = <640000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_s10c_1p05: smps10 { + regulator-min-microvolt = <1048000>; + regulator-max-microvolt = <1128000>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = ; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + vreg_l2c_1p8: ldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + vreg_l3c_3p0: ldo3 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = ; + }; + + vreg_l4c_uim1: ldo4 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = ; + }; + + vreg_l5c_uim2: ldo5 { + regulator-min-microvolt = <1704000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = ; + }; + + vreg_l6c_1p8: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = ; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = ; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = ; + }; + + vreg_l9c_2p96: ldo9 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = ; + }; + + vreg_l10c_1p2: ldo10 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-initial-mode = ; + }; + + vreg_l11c_2p96: ldo11 { + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <3008000>; + regulator-initial-mode = ; + }; + + vreg_l12c_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = ; + }; + + vreg_l13c_3p0: ldo13 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-initial-mode = ; + }; + }; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&tlmm { + gpio-reserved-ranges = <52 8>; +}; + +&uart2 { + status = "okay"; +}; From e53bdfc009770950dd23023a096542beb5f7df97 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Thu, 28 Jan 2021 02:42:20 +0300 Subject: [PATCH 513/584] arm64: dts: qcom: sm8250: Add PCIe support Add PCIe support for Qcom SM8250 SoC. This SoC has 3 PCIe Gen 3 instances based on Designware IP, out of which PCIe0 has 1 lane support and the rest have 2 lane support. Signed-off-by: Manivannan Sadhasivam [DB: add ddrss_sf_tbu clock] Signed-off-by: Dmitry Baryshkov Link: https://lore.kernel.org/r/20210127234221.947306-2-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sm8250.dtsi | 293 +++++++++++++++++++++++++++ 1 file changed, 293 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi index 61191f7f5861..947e1accae3a 100644 --- a/arch/arm64/boot/dts/qcom/sm8250.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi @@ -1231,6 +1231,299 @@ qcom,bcm-voters = <&apps_bcm_voter>; }; + pcie0: pci@1c00000 { + compatible = "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c00000 0 0x3000>, + <0 0x60000000 0 0xf1d>, + <0 0x60000f20 0 0xa8>, + <0 0x60001000 0 0x1000>, + <0 0x60100000 0 0x100000>; + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>, + <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>; + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>, + <&gcc GCC_PCIE_0_AUX_CLK>, + <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>; + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "tbu", + "ddrss_sf_tbu"; + + iommus = <&apps_smmu 0x1c00 0x7f>; + iommu-map = <0x0 &apps_smmu 0x1c00 0x1>, + <0x100 &apps_smmu 0x1c01 0x1>; + + resets = <&gcc GCC_PCIE_0_BCR>; + reset-names = "pci"; + + power-domains = <&gcc PCIE_0_GDSC>; + + phys = <&pcie0_lane>; + phy-names = "pciephy"; + + status = "disabled"; + }; + + pcie0_phy: phy@1c06000 { + compatible = "qcom,sm8250-qmp-gen3x1-pcie-phy"; + reg = <0 0x01c06000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_WIFI_CLKREF_EN>, + <&gcc GCC_PCIE0_PHY_REFGEN_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_0_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie0_lane: lanes@1c06200 { + reg = <0 0x1c06200 0 0x170>, /* tx */ + <0 0x1c06400 0 0x200>, /* rx */ + <0 0x1c06800 0 0x1f0>, /* pcs */ + <0 0x1c06c00 0 0xf4>; /* "pcs_lane" same as pcs_misc? */ + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + clock-output-names = "pcie_0_pipe_clk"; + }; + }; + + pcie1: pci@1c08000 { + compatible = "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c08000 0 0x3000>, + <0 0x40000000 0 0xf1d>, + <0 0x40000f20 0 0xa8>, + <0 0x40001000 0 0x1000>, + <0 0x40100000 0 0x100000>; + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <1>; + bus-range = <0x00 0xff>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>, + <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>; + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>, + <&gcc GCC_PCIE_1_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_1_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_AXI_CLK>, + <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>, + <&gcc GCC_PCIE_WIGIG_CLKREF_EN>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>; + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "ref", + "tbu", + "ddrss_sf_tbu"; + + assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>; + assigned-clock-rates = <19200000>; + + iommus = <&apps_smmu 0x1c80 0x7f>; + iommu-map = <0x0 &apps_smmu 0x1c80 0x1>, + <0x100 &apps_smmu 0x1c81 0x1>; + + resets = <&gcc GCC_PCIE_1_BCR>; + reset-names = "pci"; + + power-domains = <&gcc PCIE_1_GDSC>; + + phys = <&pcie1_lane>; + phy-names = "pciephy"; + + status = "disabled"; + }; + + pcie1_phy: phy@1c0e000 { + compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy"; + reg = <0 0x01c0e000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_1_CFG_AHB_CLK>, + <&gcc GCC_PCIE_WIGIG_CLKREF_EN>, + <&gcc GCC_PCIE1_PHY_REFGEN_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_1_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie1_lane: lanes@1c0e200 { + reg = <0 0x1c0e200 0 0x170>, /* tx0 */ + <0 0x1c0e400 0 0x200>, /* rx0 */ + <0 0x1c0ea00 0 0x1f0>, /* pcs */ + <0 0x1c0e600 0 0x170>, /* tx1 */ + <0 0x1c0e800 0 0x200>, /* rx1 */ + <0 0x1c0ee00 0 0xf4>; /* "pcs_com" same as pcs_misc? */ + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + clock-output-names = "pcie_1_pipe_clk"; + }; + }; + + pcie2: pci@1c10000 { + compatible = "qcom,pcie-sm8250", "snps,dw-pcie"; + reg = <0 0x01c10000 0 0x3000>, + <0 0x64000000 0 0xf1d>, + <0 0x64000f20 0 0xa8>, + <0 0x64001000 0 0x1000>, + <0 0x64100000 0 0x100000>; + reg-names = "parf", "dbi", "elbi", "atu", "config"; + device_type = "pci"; + linux,pci-domain = <2>; + bus-range = <0x00 0xff>; + num-lanes = <2>; + + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x01000000 0x0 0x64200000 0x0 0x64200000 0x0 0x100000>, + <0x02000000 0x0 0x64300000 0x0 0x64300000 0x0 0x3d00000>; + + interrupts = ; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 290 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 415 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 416 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 417 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + + clocks = <&gcc GCC_PCIE_2_PIPE_CLK>, + <&gcc GCC_PCIE_2_AUX_CLK>, + <&gcc GCC_PCIE_2_CFG_AHB_CLK>, + <&gcc GCC_PCIE_2_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_2_SLV_AXI_CLK>, + <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>, + <&gcc GCC_PCIE_MDM_CLKREF_EN>, + <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>, + <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>; + clock-names = "pipe", + "aux", + "cfg", + "bus_master", + "bus_slave", + "slave_q2a", + "ref", + "tbu", + "ddrss_sf_tbu"; + + assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>; + assigned-clock-rates = <19200000>; + + iommus = <&apps_smmu 0x1d00 0x7f>; + iommu-map = <0x0 &apps_smmu 0x1d00 0x1>, + <0x100 &apps_smmu 0x1d01 0x1>; + + resets = <&gcc GCC_PCIE_2_BCR>; + reset-names = "pci"; + + power-domains = <&gcc PCIE_2_GDSC>; + + phys = <&pcie2_lane>; + phy-names = "pciephy"; + + status = "disabled"; + }; + + pcie2_phy: phy@1c16000 { + compatible = "qcom,sm8250-qmp-modem-pcie-phy"; + reg = <0 0x1c16000 0 0x1c0>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_2_CFG_AHB_CLK>, + <&gcc GCC_PCIE_MDM_CLKREF_EN>, + <&gcc GCC_PCIE2_PHY_REFGEN_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "refgen"; + + resets = <&gcc GCC_PCIE_2_PHY_BCR>; + reset-names = "phy"; + + assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>; + assigned-clock-rates = <100000000>; + + status = "disabled"; + + pcie2_lane: lanes@1c0e200 { + reg = <0 0x1c16200 0 0x170>, /* tx0 */ + <0 0x1c16400 0 0x200>, /* rx0 */ + <0 0x1c16a00 0 0x1f0>, /* pcs */ + <0 0x1c16600 0 0x170>, /* tx1 */ + <0 0x1c16800 0 0x200>, /* rx1 */ + <0 0x1c16e00 0 0xf4>; /* "pcs_com" same as pcs_misc? */ + clocks = <&gcc GCC_PCIE_2_PIPE_CLK>; + clock-names = "pipe0"; + + #phy-cells = <0>; + clock-output-names = "pcie_2_pipe_clk"; + }; + }; + ufs_mem_hc: ufshc@1d84000 { compatible = "qcom,sm8250-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; From 418b4ee165fb225ebe76020d1fdd9bd782292263 Mon Sep 17 00:00:00 2001 From: Manivannan Sadhasivam Date: Thu, 28 Jan 2021 02:42:21 +0300 Subject: [PATCH 514/584] arm64: dts: qcom: rb5: Enable PCIe ports and PHY RB5 has 3 PCIe ports exposed to connect PCIe client devices. PCIe0 is connected to QCA6391 chipset and others are available on the HS3 expansion connector. Hence, enable all of them. Signed-off-by: Manivannan Sadhasivam Link: https://lore.kernel.org/r/20210127234221.947306-3-dmitry.baryshkov@linaro.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 117 +++++++++++++++++++++++ 1 file changed, 117 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts index 58b94ce362b2..26a4a5a6871e 100644 --- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts +++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts @@ -655,6 +655,48 @@ }; }; +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_default_state>; +}; + +&pcie0_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&pcie1 { + status = "okay"; + perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_default_state>; +}; + +&pcie1_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + +&pcie2 { + status = "okay"; + perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pcie2_default_state>; +}; + +&pcie2_phy { + status = "okay"; + vdda-phy-supply = <&vreg_l5a_0p88>; + vdda-pll-supply = <&vreg_l9a_1p2>; +}; + &pm8150_gpios { gpio-reserved-ranges = <1 1>, <3 2>, <7 1>; gpio-line-names = @@ -1125,6 +1167,81 @@ bias-disable; }; + pcie0_default_state: pcie0-default { + clkreq { + pins = "gpio80"; + function = "pci_e0"; + bias-pull-up; + }; + + reset-n { + pins = "gpio79"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio81"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie1_default_state: pcie1-default { + clkreq { + pins = "gpio83"; + function = "pci_e1"; + bias-pull-up; + }; + + reset-n { + pins = "gpio82"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio84"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + + pcie2_default_state: pcie2-default { + clkreq { + pins = "gpio86"; + function = "pci_e2"; + bias-pull-up; + }; + + reset-n { + pins = "gpio85"; + function = "gpio"; + + drive-strength = <2>; + output-low; + bias-pull-down; + }; + + wake-n { + pins = "gpio87"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + }; + sdc2_default_state: sdc2-default { clk { pins = "sdc2_clk"; From b3a6b088289ee0586b7f1f4977ade6dae06a009a Mon Sep 17 00:00:00 2001 From: Jonathan Albrieux Date: Mon, 25 Jan 2021 10:44:30 +0100 Subject: [PATCH 515/584] arm64: dts: qcom: Add device tree for BQ Aquaris X5 (Longcheer L8910) BQ Aquaris X5 (Longcheer L8910) is a smartphone using the MSM8916 SoC. Add device tree with initial support for: - SDHCI (internal and external storage) - USB Device Mode - UART - Regulators - WiFi/BT - Volume buttons - Vibrator - Touchkeys backlight This device tree is based on downstream device tree from BQ and from Longcheer L8915 device tree. Co-developed-by: Stephan Gerhold Signed-off-by: Stephan Gerhold Signed-off-by: Jonathan Albrieux Link: https://lore.kernel.org/r/20210125094435.7528-2-jonathan.albrieux@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 230 ++++++++++++++++++ 2 files changed, 231 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index ac9a1b61aab1..80ff80a9a66c 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -8,6 +8,7 @@ dtb-$(CONFIG_ARCH_QCOM) += ipq8074-hk01.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-alcatel-idol347.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-asus-z00l.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8150.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8916-longcheer-l8910.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts new file mode 100644 index 000000000000..7d5eff922f41 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts @@ -0,0 +1,230 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "msm8916-pm8916.dtsi" +#include +#include +#include + +/ { + model = "BQ Aquaris X5 (Longcheer L8910)"; + compatible = "longcheer,l8910", "qcom,msm8916"; + + aliases { + serial0 = &blsp1_uart2; + }; + + chosen { + stdout-path = "serial0"; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&gpio_keys_default>; + + label = "GPIO Buttons"; + + volume-up { + label = "Volume Up"; + gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + gpios = <&msmgpio 17 GPIO_ACTIVE_HIGH>; + color = ; + default-state = "off"; + function = LED_FUNCTION_KBD_BACKLIGHT; + + pinctrl-names = "default"; + pinctrl-0 = <&button_backlight_default>; + }; + }; + + usb_id: usb-id { + compatible = "linux,extcon-usb-gpio"; + id-gpio = <&msmgpio 110 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&usb_id_default>; + }; +}; + +&blsp1_uart2 { + status = "okay"; +}; + +&pm8916_resin { + status = "okay"; + linux,code = ; +}; + +&pm8916_vib { + status = "okay"; +}; + +&pronto { + status = "okay"; +}; + +&sdhc_1 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; + pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; +}; + +&sdhc_2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; + + cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; +}; + +&usb { + status = "okay"; + extcon = <&usb_id>, <&usb_id>; +}; + +&usb_hs_phy { + extcon = <&usb_id>; +}; + +&smd_rpm_regulators { + vdd_l1_l2_l3-supply = <&pm8916_s3>; + vdd_l4_l5_l6-supply = <&pm8916_s4>; + vdd_l7-supply = <&pm8916_s4>; + + s3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1300000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2100000>; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l4 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l8 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2900000>; + }; + + l9 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + l10 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + }; + + l11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-allow-set-load; + regulator-system-load = <200000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l13 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + l17 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l18 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; +}; + +&msmgpio { + button_backlight_default: button-backlight-default { + pins = "gpio17"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + gpio_keys_default: gpio-keys-default { + pins = "gpio107"; + function = "gpio"; + + drive-strength = <2>; + bias-pull-up; + }; + + usb_id_default: usb-id-default { + pins = "gpio110"; + function = "gpio"; + + drive-strength = <8>; + bias-pull-up; + }; +}; From 012e19f435907e2167688ff03c812e86d4e72365 Mon Sep 17 00:00:00 2001 From: Jonathan Albrieux Date: Mon, 25 Jan 2021 10:44:31 +0100 Subject: [PATCH 516/584] arm64: dts: qcom: msm8916: Add blsp_i2c3 MSM8916 has another I2C QUP controller that can be enabled on GPIO 10 and 11. Add blsp_i2c3 to msm8916.dtsi and disable it by default. Reviewed-by: Konrad Dybcio Reviewed-by: Stephan Gerhold Signed-off-by: Jonathan Albrieux Link: https://lore.kernel.org/r/20210125094435.7528-3-jonathan.albrieux@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8916-pins.dtsi | 16 ++++++++++++++++ arch/arm64/boot/dts/qcom/msm8916.dtsi | 15 +++++++++++++++ 2 files changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi index 4dc437f13fa5..7dedb91b9930 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916-pins.dtsi @@ -220,6 +220,22 @@ bias-disable; }; + i2c3_default: i2c3-default { + pins = "gpio10", "gpio11"; + function = "blsp_i2c3"; + + drive-strength = <2>; + bias-disable; + }; + + i2c3_sleep: i2c3-sleep { + pins = "gpio10", "gpio11"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + i2c4_default: i2c4-default { pins = "gpio14", "gpio15"; function = "blsp_i2c4"; diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index 8f9a651d3827..c82ac0521e0c 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -1529,6 +1529,21 @@ status = "disabled"; }; + blsp_i2c3: i2c@78b7000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b7000 0x500>; + interrupts = ; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>; + clock-names = "iface", "core"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c3_default>; + pinctrl-1 = <&i2c3_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + blsp_spi3: spi@78b7000 { compatible = "qcom,spi-qup-v2.2.1"; reg = <0x078b7000 0x500>; From dcac40943c0503d7ed3958fc86ff0b581776a48f Mon Sep 17 00:00:00 2001 From: Jonathan Albrieux Date: Mon, 25 Jan 2021 10:44:32 +0100 Subject: [PATCH 517/584] arm64: dts: qcom: msm8916-longcheer-l8910: Add imu/magnetometer BQ Aquaris X5 (Longcheer L8910) has: - BMI160 accelerometer and gyroscope sensor - AK09911 magnetometer sensor Add them to the device tree. This patch depends on patch "arm64: dts: qcom: msm8916: Add blsp_i2c3". Reviewed-by: Stephan Gerhold Signed-off-by: Jonathan Albrieux Link: https://lore.kernel.org/r/20210125094435.7528-4-jonathan.albrieux@gmail.com Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom/msm8916-longcheer-l8910.dts | 37 +++++++++++++++++++ 1 file changed, 37 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts index 7d5eff922f41..27845189ac2b 100644 --- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts +++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts @@ -56,6 +56,35 @@ }; }; +&blsp_i2c3 { + status = "okay"; + + magnetometer@d { + compatible = "asahi-kasei,ak09911"; + reg = <0x0d>; + + vdd-supply = <&pm8916_l17>; + vid-supply = <&pm8916_l6>; + + reset-gpios = <&msmgpio 111 GPIO_ACTIVE_LOW>; + + pinctrl-names = "default"; + pinctrl-0 = <&mag_reset_default>; + }; + + imu@68 { + compatible = "bosch,bmi160"; + reg = <0x68>; + + vdd-supply = <&pm8916_l17>; + vddio-supply = <&pm8916_l6>; + + mount-matrix = "0", "1", "0", + "-1", "0", "0", + "0", "0", "1"; + }; +}; + &blsp1_uart2 { status = "okay"; }; @@ -220,6 +249,14 @@ bias-pull-up; }; + mag_reset_default: mag-reset-default { + pins = "gpio111"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + usb_id_default: usb-id-default { pins = "gpio110"; function = "gpio"; From 886ddcfe4aa44c20e4d0da49af0b01b0e3048322 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sun, 31 Jan 2021 02:38:32 +0100 Subject: [PATCH 518/584] arm64: dts: qcom: msm8994: Add SMP2P nodes They will be required for bringup of remote processors. Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-2-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8994.dtsi | 49 +++++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index e694aaad3c99..af1a9f7907b8 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -276,6 +276,55 @@ hwlocks = <&tcsr_mutex 3>; }; + smp2p-lpass { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + + interrupts = ; + + qcom,ipc = <&apcs 8 10>; + + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + adsp_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + adsp_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-modem { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupt-parent = <&intc>; + interrupts = ; + + qcom,ipc = <&apcs 8 14>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + modem_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + #qcom,smem-state-cells = <1>; + }; + + modem_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + soc: soc { #address-cells = <1>; From e093d1a2875c1c1050d190fb5de0712173e340ad Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:33 +0100 Subject: [PATCH 519/584] arm64: dts: qcom: msm8994: Fix remaining BLSP errors/mistakes * Move 35500 clock-frequency to kitakami (turns out it's a Sony specific) * Add missing interfaces * Fix the naming scheme * Fix up pin assignments to make all BLSPs work * Add DMA where previously omitted Signed-off-by: Gustave Monce Co-developed-by: Konrad Dybcio Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-3-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-cityman.dts | 2 +- .../msm8994-sony-xperia-kitakami-karin.dts | 2 +- .../qcom/msm8994-sony-xperia-kitakami.dtsi | 24 ++- arch/arm64/boot/dts/qcom/msm8994.dtsi | 173 ++++++++++++++---- 4 files changed, 154 insertions(+), 47 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts index ed9034b96013..2d989a70e0b5 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts @@ -32,7 +32,7 @@ }; }; -&blsp_i2c1 { +&blsp1_i2c1 { status = "okay"; rmi4-i2c-dev@4b { diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts index 4dcf42eafb3a..a1d1a075941a 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami-karin.dts @@ -12,7 +12,7 @@ compatible = "sony,karin-row", "qcom,msm8994"; }; -&blsp_i2c5 { +&blsp2_i2c5 { /* * TI LP8557 backlight driver @ 2c * AD AD7146 touch controller @ 2f diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi index 586d866188d7..48de66bf19c4 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi @@ -94,7 +94,7 @@ }; }; -&blsp_spi0 { +&blsp1_spi1 { status = "okay"; /* FPC fingerprint reader */ @@ -102,26 +102,23 @@ /* I2C1 is disabled on this board */ -&blsp_i2c2 { +&blsp1_i2c2 { status = "okay"; + clock-frequency = <355000>; /* NXP PN547 NFC */ }; -&blsp_i2c4 { +&blsp1_i2c4 { status = "okay"; + clock-frequency = <355000>; /* Empty but active */ }; -&blsp_i2c5 { - status = "okay"; - - /* sii8620 HDMI/MHL bridge */ -}; - -&blsp_i2c6 { +&blsp1_i2c6 { status = "okay"; + clock-frequency = <355000>; touchscreen: rmi4-i2c-dev@2c { compatible = "syna,rmi4-i2c"; @@ -157,6 +154,13 @@ status = "okay"; }; +&blsp2_i2c5 { + status = "okay"; + clock-frequency = <355000>; + + /* sii8620 HDMI/MHL bridge */ +}; + &blsp2_uart2 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index af1a9f7907b8..a6148b00e82c 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -507,7 +507,7 @@ status = "disabled"; }; - blsp_i2c1: i2c@f9923000 { + blsp1_i2c1: i2c@f9923000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9923000 0x500>; interrupts = ; @@ -515,6 +515,8 @@ <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>; clock-names = "iface", "core"; clock-frequency = <400000>; + dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c1_default>; pinctrl-1 = <&i2c1_sleep>; @@ -523,7 +525,7 @@ status = "disabled"; }; - blsp_spi0: spi@f9923000 { + blsp1_spi1: spi@f9923000 { compatible = "qcom,spi-qup-v2.2.1"; reg = <0xf9923000 0x500>; interrupts = ; @@ -534,21 +536,21 @@ dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp1_spi0_default>; - pinctrl-1 = <&blsp1_spi0_sleep>; + pinctrl-0 = <&blsp1_spi1_default>; + pinctrl-1 = <&blsp1_spi1_sleep>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; }; - blsp_i2c2: i2c@f9924000 { + blsp1_i2c2: i2c@f9924000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9924000 0x500>; interrupts = ; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; clock-names = "iface", "core"; - clock-frequency = <355000>; + clock-frequency = <400000>; dmas = <&blsp1_dma 14>, <&blsp1_dma 15>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; @@ -561,14 +563,16 @@ /* I2C3 doesn't exist */ - blsp_i2c4: i2c@f9926000 { + blsp1_i2c4: i2c@f9926000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9926000 0x500>; interrupts = ; clocks = <&gcc GCC_BLSP1_AHB_CLK>, <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>; clock-names = "iface", "core"; - clock-frequency = <355000>; + clock-frequency = <400000>; + dmas = <&blsp1_dma 18>, <&blsp1_dma 19>; + dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c4_default>; pinctrl-1 = <&i2c4_sleep>; @@ -577,6 +581,42 @@ status = "disabled"; }; + blsp1_i2c5: i2c@f9927000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9927000 0x500>; + interrupts = ; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp2_dma 20>, <&blsp2_dma 21>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c5_default>; + pinctrl-1 = <&i2c5_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c6: i2c@f9928000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9928000 0x500>; + interrupts = ; + clocks = <&gcc GCC_BLSP1_AHB_CLK>, + <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp1_dma 22>, <&blsp1_dma 23>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c6_default>; + pinctrl-1 = <&i2c6_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + blsp2_dma: dma-controller@f9944000 { compatible = "qcom,bam-v1.7.0"; reg = <0xf9944000 0x19000>; @@ -590,28 +630,6 @@ qcom,num-ees = <4>; }; - /* According to downstream kernels, i2c6 - * comes before i2c5 address-wise... - */ - - blsp_i2c6: i2c@f9928000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9928000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <355000>; - dmas = <&blsp1_dma 22>, <&blsp1_dma 23>; - dma-names = "tx", "rx"; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c6_default>; - pinctrl-1 = <&i2c6_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - blsp2_uart2: serial@f995e000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0xf995e000 0x1000>; @@ -627,7 +645,43 @@ status = "disabled"; }; - blsp_i2c5: i2c@f9967000 { + blsp2_i2c1: i2c@f9963000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0xf9963000 0x500>; + interrupts = ; + clocks = <&gcc GCC_BLSP2_AHB_CLK>, + <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>; + clock-names = "iface", "core"; + clock-frequency = <400000>; + dmas = <&blsp2_dma 12>, <&blsp2_dma 13>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&i2c7_default>; + pinctrl-1 = <&i2c7_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_spi4: spi@f9966000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0xf9966000 0x500>; + interrupts = ; + clocks = <&gcc GCC_BLSP2_QUP4_SPI_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + spi-max-frequency = <19200000>; + dmas = <&blsp2_dma 18>, <&blsp2_dma 19>; + dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_spi10_default>; + pinctrl-1 = <&blsp2_spi10_sleep>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_i2c5: i2c@f9967000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0xf9967000 0x500>; interrupts = ; @@ -638,8 +692,8 @@ dmas = <&blsp2_dma 20>, <&blsp2_dma 21>; dma-names = "tx", "rx"; pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c5_default>; - pinctrl-1 = <&i2c5_sleep>; + pinctrl-0 = <&i2c11_default>; + pinctrl-1 = <&i2c11_sleep>; #address-cells = <1>; #size-cells = <0>; status = "disabled"; @@ -795,7 +849,56 @@ bias-disable; }; - blsp1_spi0_default: blsp1-spi0-default { + i2c7_default: i2c7-default { + function = "blsp_i2c7"; + pins = "gpio44", "gpio43"; + drive-strength = <2>; + bias-disable; + }; + + i2c7_sleep: i2c7-sleep { + function = "gpio"; + pins = "gpio44", "gpio43"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_spi10_default: blsp2-spi10-default { + default { + function = "blsp_spi10"; + pins = "gpio53", "gpio54", "gpio55"; + drive-strength = <10>; + bias-pull-down; + }; + cs { + function = "gpio"; + pins = "gpio55"; + drive-strength = <2>; + bias-disable; + }; + }; + + blsp2_spi10_sleep: blsp2-spi10-sleep { + pins = "gpio53", "gpio54", "gpio55"; + drive-strength = <2>; + bias-disable; + }; + + i2c11_default: i2c11-default { + function = "blsp_i2c11"; + pins = "gpio83", "gpio84"; + drive-strength = <2>; + bias-disable; + }; + + i2c11_sleep: i2c11-sleep { + function = "gpio"; + pins = "gpio83", "gpio84"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_spi1_default: blsp1-spi1-default { default { function = "blsp_spi1"; pins = "gpio0", "gpio1", "gpio3"; @@ -810,7 +913,7 @@ }; }; - blsp1_spi0_sleep: blsp1-spi0-sleep { + blsp1_spi1_sleep: blsp1-spi1-sleep { pins = "gpio0", "gpio1", "gpio3"; drive-strength = <2>; bias-disable; From 76d0b35c7f84f70219eca8f920b71f9d85f8899e Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sun, 31 Jan 2021 02:38:34 +0100 Subject: [PATCH 520/584] arm64: dts: qcom: msm8994: Sort hwlock properly Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-4-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8994.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index a6148b00e82c..60e04514af70 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -155,6 +155,12 @@ reg = <0 0 0 0>; }; + tcsr_mutex: hwlock { + compatible = "qcom,tcsr-mutex"; + syscon = <&tcsr_mutex_regs 0 0x80>; + #hwlock-cells = <1>; + }; + pmu { compatible = "arm,cortex-a53-pmu"; interrupts = ; @@ -1003,12 +1009,6 @@ }; }; - tcsr_mutex: hwlock { - compatible = "qcom,tcsr-mutex"; - syscon = <&tcsr_mutex_regs 0 0x80>; - #hwlock-cells = <1>; - }; - timer { compatible = "arm,armv8-timer"; interrupts = , From 976d321f32dcf569738af2bab79d7041a6fb64b5 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sun, 31 Jan 2021 02:38:35 +0100 Subject: [PATCH 521/584] arm64: dts: qcom: msm8992: Make the DT an overlay on top of 8994 This saves a good thousand lines of code, perhaps even more in the long run. Co-developed-by: Gustave Monce Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-5-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8992-bullhead-rev-101.dts | 2 +- .../boot/dts/qcom/msm8992-xiaomi-libra.dts | 69 +- arch/arm64/boot/dts/qcom/msm8992.dtsi | 772 +----------------- arch/arm64/boot/dts/qcom/msm8994.dtsi | 6 +- 4 files changed, 51 insertions(+), 798 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts index cacbfdbd69e3..23cdcc9f7c72 100644 --- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts +++ b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts @@ -283,7 +283,7 @@ }; }; -&sdhc_1 { +&sdhc1 { status = "okay"; mmc-hs400-1_8v; diff --git a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts index 5dab8ee0c7d3..357d55496e75 100644 --- a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts +++ b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts @@ -70,21 +70,6 @@ pmsg-size = <0x20000>; }; - continuous_splash: framebuffer@3401000{ - reg = <0x0 0x3401000 0x0 0x2200000>; - no-map; - }; - - dfps_data_mem: dfps_data_mem@3400000 { - reg = <0x0 0x3400000 0x0 0x1000>; - no-map; - }; - - peripheral_region: peripheral_region@7400000 { - reg = <0x0 0x7400000 0x0 0x1c00000>; - no-map; - }; - modem_region: modem_region@9000000 { reg = <0x0 0x9000000 0x0 0x5a00000>; no-map; @@ -97,43 +82,49 @@ }; }; -&blsp_i2c2 { +&blsp1_i2c2 { status = "okay"; /* Atmel or Synaptics touchscreen */ }; -&blsp_i2c5 { - status = "okay"; - - /* Silabs si4705 FM transmitter */ -}; - -&blsp_i2c6 { - status = "okay"; - - /* NCI NFC, - * TI USB320 Type-C controller, - * Pericom 30216a USB (de)mux switch - */ -}; - -&blsp_i2c7 { - status = "okay"; - - /* cm36686 proximity and ambient light sensor */ -}; - -&blsp_i2c13 { +&blsp1_i2c5 { status = "okay"; /* ST lsm6db0 gyro/accelerometer */ }; +&blsp1_i2c6 { + status = "okay"; + + /* + * NXP NCI NFC, + * TI USB320 Type-C controller, + * Pericom 30216a USB (de)mux switch + */ +}; + +&blsp2_i2c1 { + status = "okay"; + + /* cm36686 proximity and ambient light sensor */ +}; + +&blsp2_i2c5 { + status = "okay"; + + /* Silabs si4705 FM transmitter */ +}; + &blsp2_uart2 { status = "okay"; }; +&peripheral_region { + reg = <0x0 0x7400000 0x0 0x1c00000>; + no-map; +}; + &rpm_requests { pm8994-regulators { compatible = "qcom,rpm-pm8994-regulators"; @@ -364,7 +355,7 @@ }; }; -&sdhc_1 { +&sdhc1 { status = "okay"; mmc-hs400-1_8v; diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi index b2046497dcaa..58fe58cc7703 100644 --- a/arch/arm64/boot/dts/qcom/msm8992.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi @@ -2,767 +2,29 @@ /* Copyright (c) 2013-2016, The Linux Foundation. All rights reserved. */ -#include -#include -#include +#include "msm8994.dtsi" -/ { - interrupt-parent = <&intc>; +/* 8992 only features 2 A57 cores. */ +/delete-node/ &CPU6; +/delete-node/ &CPU7; +/delete-node/ &cpu6_map; +/delete-node/ &cpu7_map; - #address-cells = <2>; - #size-cells = <2>; +&rpmcc { + compatible = "qcom,rpmcc-msm8992"; +}; - chosen { }; +&tcsr_mutex { + compatible = "qcom,sfpb-mutex"; +}; - cpus { - #address-cells = <2>; - #size-cells = <0>; - - CPU0: cpu@0 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x0>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - L2_0: l2-cache { - compatible = "cache"; - cache-level = <2>; - }; - }; - - CPU1: cpu@1 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x1>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - }; - - CPU2: cpu@2 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x2>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - }; - - CPU3: cpu@3 { - device_type = "cpu"; - compatible = "arm,cortex-a53"; - reg = <0x0 0x3>; - next-level-cache = <&L2_0>; - enable-method = "psci"; - }; - - CPU4: cpu@100 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x100>; - next-level-cache = <&L2_1>; - enable-method = "psci"; - L2_1: l2-cache { - compatible = "cache"; - cache-level = <2>; - }; - }; - - CPU5: cpu@101 { - device_type = "cpu"; - compatible = "arm,cortex-a57"; - reg = <0x0 0x101>; - next-level-cache = <&L2_1>; - enable-method = "psci"; - }; - - cpu-map { - cluster0 { - core0 { - cpu = <&CPU0>; - }; - - core1 { - cpu = <&CPU1>; - }; - - core2 { - cpu = <&CPU2>; - }; - - core3 { - cpu = <&CPU3>; - }; - }; - - cluster1 { - core0 { - cpu = <&CPU4>; - }; - - core1 { - cpu = <&CPU5>; - }; - }; - }; - }; - - clocks { - xo_board: xo_board { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <19200000>; - }; - - sleep_clk: sleep_clk { - compatible = "fixed-clock"; - #clock-cells = <0>; - clock-frequency = <32768>; - }; - }; - - firmware { - scm { - compatible = "qcom,scm-msm8994", "qcom,scm"; - }; - }; - - memory { - device_type = "memory"; - /* We expect the bootloader to fill in the reg */ - reg = <0 0 0 0>; - }; - - pmu { - compatible = "arm,cortex-a53-pmu"; - interrupts = ; - }; - - psci { - compatible = "arm,psci-0.2"; - method = "hvc"; - }; - - reserved-memory { - #address-cells = <2>; - #size-cells = <2>; - ranges; - - smem_region: smem@6a00000 { - reg = <0x0 0x6a00000 0x0 0x200000>; - no-map; - }; - }; - - sfpb_mutex: hwmutex { - compatible = "qcom,sfpb-mutex"; - syscon = <&sfpb_mutex_regs 0x0 0x100>; - #hwlock-cells = <1>; - }; - - smem { - compatible = "qcom,smem"; - memory-region = <&smem_region>; - qcom,rpm-msg-ram = <&rpm_msg_ram>; - hwlocks = <&sfpb_mutex 3>; - }; - - soc { - #address-cells = <1>; - #size-cells = <1>; - ranges = <0 0 0 0xffffffff>; - compatible = "simple-bus"; - - intc: interrupt-controller@f9000000 { - compatible = "qcom,msm-qgic2"; - interrupt-controller; - #interrupt-cells = <3>; - reg = <0xf9000000 0x1000>, - <0xf9002000 0x1000>; - }; - - apcs: mailbox@f900d000 { - compatible = "qcom,msm8994-apcs-kpss-global", "syscon"; - reg = <0xf900d000 0x2000>; - #mbox-cells = <1>; - }; - - timer@f9020000 { - #address-cells = <1>; - #size-cells = <1>; - ranges; - compatible = "arm,armv7-timer-mem"; - reg = <0xf9020000 0x1000>; - - frame@f9021000 { - frame-number = <0>; - interrupts = , - ; - reg = <0xf9021000 0x1000>, - <0xf9022000 0x1000>; - }; - - frame@f9023000 { - frame-number = <1>; - interrupts = ; - reg = <0xf9023000 0x1000>; - status = "disabled"; - }; - - frame@f9024000 { - frame-number = <2>; - interrupts = ; - reg = <0xf9024000 0x1000>; - status = "disabled"; - }; - - frame@f9025000 { - frame-number = <3>; - interrupts = ; - reg = <0xf9025000 0x1000>; - status = "disabled"; - }; - - frame@f9026000 { - frame-number = <4>; - interrupts = ; - reg = <0xf9026000 0x1000>; - status = "disabled"; - }; - - frame@f9027000 { - frame-number = <5>; - interrupts = ; - reg = <0xf9027000 0x1000>; - status = "disabled"; - }; - - frame@f9028000 { - frame-number = <6>; - interrupts = ; - reg = <0xf9028000 0x1000>; - status = "disabled"; - }; - }; - - usb3: usb@f92f8800 { - compatible = "qcom,msm8996-dwc3", "qcom,dwc3"; - reg = <0xf92f8800 0x400>; - #address-cells = <1>; - #size-cells = <1>; - ranges; - - clocks = <&gcc GCC_USB30_MASTER_CLK>, - <&gcc GCC_SYS_NOC_USB3_AXI_CLK>, - <&gcc GCC_USB30_SLEEP_CLK>, - <&gcc GCC_USB30_MOCK_UTMI_CLK>; - clock-names = "core", "iface", "sleep", "mock_utmi", "ref", "xo"; - - assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, - <&gcc GCC_USB30_MASTER_CLK>; - assigned-clock-rates = <19200000>, <120000000>; - - power-domains = <&gcc USB30_GDSC>; - qcom,select-utmi-as-pipe-clk; - - dwc3@f9200000 { - compatible = "snps,dwc3"; - reg = <0xf9200000 0xcc00>; - interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>; - snps,dis_u2_susphy_quirk; - snps,dis_enblslpm_quirk; - maximum-speed = "high-speed"; - dr_mode = "peripheral"; - }; - }; - - sdhc_1: sdhci@f9824900 { - compatible = "qcom,sdhci-msm-v4"; - reg = <0xf9824900 0x1a0>, <0xf9824000 0x800>; - reg-names = "hc_mem", "core_mem"; - - interrupts = , - ; - interrupt-names = "hc_irq", "pwr_irq"; - - clocks = <&gcc GCC_SDCC1_APPS_CLK>, - <&gcc GCC_SDCC1_AHB_CLK>, - <&xo_board>; - clock-names = "core", "iface", "xo"; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on - &sdc1_rclk_on>; - pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off - &sdc1_rclk_off>; - - regulator-always-on; - bus-width = <8>; - non-removable; - - status = "disabled"; - }; - - sdhc_2: sdhci@f98a4900 { - compatible = "qcom,sdhci-msm-v4"; - reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>; - reg-names = "hc_mem", "core_mem"; - - interrupts = , - ; - interrupt-names = "hc_irq", "pwr_irq"; - - clocks = <&gcc GCC_SDCC2_APPS_CLK>, - <&gcc GCC_SDCC2_AHB_CLK>, - <&xo_board>; - clock-names = "core", "iface", "xo"; - - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; - pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; - - cd-gpios = <&tlmm 100 0>; - bus-width = <4>; - status = "disabled"; - }; - - blsp1_uart2: serial@f991e000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0xf991e000 0x1000>; - interrupts = ; - clock-names = "core", "iface"; - clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, - <&gcc GCC_BLSP1_AHB_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp1_uart2_default>; - pinctrl-1 = <&blsp1_uart2_sleep>; - status = "disabled"; - }; - - blsp_i2c1: i2c@f9923000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9923000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c1_default>; - pinctrl-1 = <&i2c1_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp_i2c2: i2c@f9924000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9924000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c2_default>; - pinctrl-1 = <&i2c2_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - /* Somebody was very creative with their numbering scheme downstream... */ - - blsp_i2c13: i2c@f9927000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9927000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c13_default>; - pinctrl-1 = <&i2c13_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp_i2c6: i2c@f9928000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9928000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP1_AHB_CLK>, - <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c6_default>; - pinctrl-1 = <&i2c6_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp2_uart2: serial@f995e000 { - compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; - reg = <0xf995e000 0x1000>; - interrupts = ; - clock-names = "core", "iface"; - clocks = <&gcc GCC_BLSP2_UART2_APPS_CLK>, - <&gcc GCC_BLSP2_AHB_CLK>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&blsp2_uart2_default>; - pinctrl-1 = <&blsp2_uart2_sleep>; - status = "disabled"; - }; - - blsp_i2c7: i2c@f9963000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9963000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP2_AHB_CLK>, - <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <400000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c7_default>; - pinctrl-1 = <&i2c7_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - blsp_i2c5: i2c@f9967000 { - compatible = "qcom,i2c-qup-v2.2.1"; - reg = <0xf9967000 0x500>; - interrupts = ; - clocks = <&gcc GCC_BLSP2_AHB_CLK>, - <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>; - clock-names = "iface", "core"; - clock-frequency = <100000>; - pinctrl-names = "default", "sleep"; - pinctrl-0 = <&i2c5_default>; - pinctrl-1 = <&i2c5_sleep>; - #address-cells = <1>; - #size-cells = <0>; - status = "disabled"; - }; - - gcc: clock-controller@fc400000 { - compatible = "qcom,gcc-msm8994"; - #clock-cells = <1>; - #reset-cells = <1>; - #power-domain-cells = <1>; - reg = <0xfc400000 0x2000>; - }; - - rpm_msg_ram: memory@fc428000 { - compatible = "qcom,rpm-msg-ram"; - reg = <0xfc428000 0x4000>; - }; - - restart@fc4ab000 { - compatible = "qcom,pshold"; - reg = <0xfc4ab000 0x4>; - }; - - spmi_bus: spmi@fc4c0000 { - compatible = "qcom,spmi-pmic-arb"; - reg = <0xfc4cf000 0x1000>, - <0xfc4cb000 0x1000>, - <0xfc4ca000 0x1000>; - reg-names = "core", "intr", "cnfg"; - interrupt-names = "periph_irq"; - interrupts = ; - qcom,ee = <0>; - qcom,channel = <0>; - #address-cells = <2>; - #size-cells = <0>; - interrupt-controller; - #interrupt-cells = <4>; - }; - - sfpb_mutex_regs: syscon@fd484000 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "syscon"; - reg = <0xfd484000 0x400>; - }; - - tlmm: pinctrl@fd510000 { - compatible = "qcom,msm8994-pinctrl"; - reg = <0xfd510000 0x4000>; - interrupts = ; - gpio-controller; - gpio-ranges = <&tlmm 0 0 146>; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - - blsp1_uart2_default: blsp1-uart2-default { - function = "blsp_uart2"; - pins = "gpio4", "gpio5"; - drive-strength = <16>; - bias-disable; - }; - - blsp1_uart2_sleep: blsp1-uart2-sleep { - function = "gpio"; - pins = "gpio4", "gpio5"; - drive-strength = <2>; - bias-pull-down; - }; - - blsp2_uart2_default: blsp2-uart2-default { - function = "blsp_uart8"; - pins = "gpio45", "gpio46", "gpio47", "gpio48"; - drive-strength = <16>; - bias-disable; - }; - - blsp2_uart2_sleep: blsp2-uart2-sleep { - function = "gpio"; - pins = "gpio45", "gpio46", "gpio47", "gpio48"; - drive-strength = <2>; - bias-pull-down; - }; - - sdc1_clk_on: clk-on { - pins = "sdc1_clk"; - bias-disable; - drive-strength = <6>; - }; - - sdc1_clk_off: clk-off { - pins = "sdc1_clk"; - bias-disable; - drive-strength = <2>; - }; - - sdc1_cmd_on: cmd-on { - pins = "sdc1_cmd"; - bias-pull-up; - drive-strength = <6>; - }; - - sdc1_cmd_off: cmd-off { - pins = "sdc1_cmd"; - bias-pull-up; - drive-strength = <2>; - }; - - sdc1_data_on: data-on { - pins = "sdc1_data"; - bias-pull-up; - drive-strength = <6>; - }; - - sdc1_data_off: data-off { - pins = "sdc1_data"; - bias-pull-up; - drive-strength = <2>; - }; - - sdc1_rclk_on: rclk-on { - pins = "sdc1_rclk"; - bias-pull-down; - }; - - sdc1_rclk_off: rclk-off { - pins = "sdc1_rclk"; - bias-pull-down; - }; - - i2c1_default: i2c1-default { - function = "blsp_i2c1"; - pins = "gpio2", "gpio3"; - drive-strength = <2>; - bias-disable; - }; - - i2c1_sleep: i2c1-sleep { - function = "gpio"; - pins = "gpio2", "gpio3"; - drive-strength = <2>; - bias-disable; - }; - - i2c2_default: i2c2-default { - function = "blsp_i2c2"; - pins = "gpio6", "gpio7"; - drive-strength = <2>; - bias-disable; - }; - - i2c2_sleep: i2c2-sleep { - function = "gpio"; - pins = "gpio6", "gpio7"; - drive-strength = <2>; - bias-disable; - }; - - i2c5_default: i2c5-default { - /* Don't be fooled! Nobody knows the reason why though... */ - function = "blsp_i2c11"; - pins = "gpio83", "gpio84"; - drive-strength = <2>; - bias-disable; - }; - - i2c5_sleep: i2c5-sleep { - function = "gpio"; - pins = "gpio83", "gpio84"; - drive-strength = <2>; - bias-disable; - }; - - i2c6_default: i2c6-default { - function = "blsp_i2c6"; - pins = "gpio28", "gpio27"; - drive-strength = <2>; - bias-disable; - }; - - i2c6_sleep: i2c6-sleep { - function = "gpio"; - pins = "gpio28", "gpio27"; - drive-strength = <2>; - bias-disable; - }; - - i2c7_default: i2c7-default { - function = "blsp_i2c7"; - pins = "gpio43", "gpio44"; - drive-strength = <2>; - bias-disable; - }; - - i2c7_sleep: i2c7-sleep { - function = "gpio"; - pins = "gpio43", "gpio44"; - drive-strength = <2>; - bias-disable; - }; - - i2c13_default: i2c13-default { - /* Not a typo either. */ - function = "blsp_i2c5"; - pins = "gpio23", "gpio24"; - drive-strength = <2>; - bias-disable; - }; - - i2c13_sleep: i2c13-sleep { - function = "gpio"; - pins = "gpio23", "gpio24"; - drive-strength = <2>; - bias-disable; - }; - - sdc2_clk_on: sdc2-clk-on { - pins = "sdc2_clk"; - bias-disable; - drive-strength = <16>; - }; - - sdc2_clk_off: sdc2-clk-off { - pins = "sdc2_clk"; - bias-disable; - drive-strength = <2>; - }; - - sdc2_cmd_on: sdc2-cmd-on { - pins = "sdc2_cmd"; - bias-pull-up; - drive-strength = <10>; - }; - - sdc2_cmd_off: sdc2-cmd-off { - pins = "sdc2_cmd"; - bias-pull-up; - drive-strength = <2>; - }; - - sdc2_data_on: sdc2-data-on { - pins = "sdc2_data"; - bias-pull-up; - drive-strength = <10>; - }; - - sdc2_data_off: sdc2-data-off { - pins = "sdc2_data"; - bias-pull-up; - drive-strength = <2>; - }; - }; - }; - - smd_rpm: smd { - compatible = "qcom,smd"; - rpm { - interrupts = ; - qcom,ipc = <&apcs 8 0>; - qcom,smd-edge = <15>; - qcom,local-pid = <0>; - qcom,remote-pid = <6>; - - rpm_requests: rpm-requests { - compatible = "qcom,rpm-msm8994"; - qcom,smd-channels = "rpm_requests"; - - rpmcc: rpmcc { - compatible = "qcom,rpmcc-msm8992"; - #clock-cells = <1>; - }; - - rpmpd: power-controller { - compatible = "qcom,msm8994-rpmpd"; - #power-domain-cells = <1>; - operating-points-v2 = <&rpmpd_opp_table>; - - rpmpd_opp_table: opp-table { - compatible = "operating-points-v2"; - - rpmpd_opp_ret: opp1 { - opp-level = <1>; - }; - rpmpd_opp_svs_krait: opp2 { - opp-level = <2>; - }; - rpmpd_opp_svs_soc: opp3 { - opp-level = <3>; - }; - rpmpd_opp_nom: opp4 { - opp-level = <4>; - }; - rpmpd_opp_turbo: opp5 { - opp-level = <5>; - }; - rpmpd_opp_super_turbo: opp6 { - opp-level = <6>; - }; - }; - }; - }; - }; - }; - - timer { - compatible = "arm,armv8-timer"; - interrupts = , +&timer { + interrupts = , , , ; - }; - - vph_pwr: vph-pwr-regulator { - compatible = "regulator-fixed"; - regulator-name = "vph_pwr"; - - regulator-min-microvolt = <3600000>; - regulator-max-microvolt = <3600000>; - - regulator-always-on; - }; }; +&tlmm { + compatible = "qcom,msm8992-pinctrl"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi index 60e04514af70..f49d442d2edf 100644 --- a/arch/arm64/boot/dts/qcom/msm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi @@ -132,11 +132,11 @@ cpu = <&CPU5>; }; - core2 { + cpu6_map: core2 { cpu = <&CPU6>; }; - core3 { + cpu7_map: core3 { cpu = <&CPU7>; }; }; @@ -1009,7 +1009,7 @@ }; }; - timer { + timer: timer { compatible = "arm,armv8-timer"; interrupts = , , From c6e72bd747b014b3fdfba3bf7a744e94447f8b43 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:36 +0100 Subject: [PATCH 522/584] arm64: dts: qcom: msm8992/4-lumia*: Create a common DTS Lumia 950 and 950XL are both based on the Octagon board, sharing the vast majority of components, configuration etc. Commonize it. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-6-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/Makefile | 4 +- .../msm8992-msft-lumia-octagon-talkman.dts | 15 +++++ .../dts/qcom/msm8992-msft-lumia-talkman.dts | 67 ------------------- .../msm8994-msft-lumia-octagon-cityman.dts | 15 +++++ ...an.dts => msm8994-msft-lumia-octagon.dtsi} | 14 ++-- 5 files changed, 38 insertions(+), 77 deletions(-) create mode 100644 arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts delete mode 100644 arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts create mode 100644 arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts rename arch/arm64/boot/dts/qcom/{msm8994-msft-lumia-cityman.dts => msm8994-msft-lumia-octagon.dtsi} (81%) diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 80ff80a9a66c..549a7a2151d4 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -13,10 +13,10 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-mtp.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a3u-eur.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8916-samsung-a5u-eur.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-bullhead-rev-101.dtb -dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-talkman.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8992-msft-lumia-octagon-talkman.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8992-xiaomi-libra.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-angler-rev-101.dtb -dtb-$(CONFIG_ARCH_QCOM) += msm8994-msft-lumia-cityman.dtb +dtb-$(CONFIG_ARCH_QCOM) += msm8994-msft-lumia-octagon-cityman.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-ivy.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-karin.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-satsuki.dtb diff --git a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts new file mode 100644 index 000000000000..5322b9ce5839 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-octagon-talkman.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Gustave Monce + */ + +/dts-v1/; + +#include "msm8992.dtsi" +#include "msm8994-msft-lumia-octagon.dtsi" + +/ { + model = "Microsoft Lumia 950"; + compatible = "microsoft,talkman", "qcom,msm8992"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts b/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts deleted file mode 100644 index c337a86a5c77..000000000000 --- a/arch/arm64/boot/dts/qcom/msm8992-msft-lumia-talkman.dts +++ /dev/null @@ -1,67 +0,0 @@ -// SPDX-License-Identifier: BSD-3-Clause -/* - * Copyright (c) 2020, Konrad Dybcio - */ - -/dts-v1/; - -#include "msm8992.dtsi" -#include "pm8994.dtsi" -#include "pmi8994.dtsi" -#include -#include - -/ { - model = "Microsoft Lumia 950"; - compatible = "microsoft,talkman", "qcom,msm8992"; - - /* Most Lumia 950 users use GRUB to load their kernels, - * hence there is no need for msm-id and friends. - */ - - /* This enables graphical output via bootloader-enabled display. - * acpi=no is required due to WP platforms having ACPI support, but - * only for Windows-based OSes. - */ - chosen { - bootargs = "earlycon=efifb console=efifb acpi=no"; - - #address-cells = <2>; - #size-cells = <2>; - ranges; - }; -}; - -&blsp_i2c1 { - status = "okay"; - - rmi4-i2c-dev@4b { - compatible = "syna,rmi4-i2c"; - reg = <0x4b>; - #address-cells = <1>; - #size-cells = <0>; - - interrupt-parent = <&tlmm>; - interrupts = <77 IRQ_TYPE_EDGE_FALLING>; - - rmi4-f01@1 { - reg = <0x01>; - syna,nosleep-mode = <1>; - }; - - rmi4-f12@12 { - reg = <0x12>; - syna,sensor-type = <1>; - syna,clip-x-low = <0>; - syna,clip-x-high = <1440>; - syna,clip-y-low = <0>; - syna,clip-y-high = <2560>; - }; - }; -}; - -&sdhc_1 { - status = "okay"; - - mmc-hs200-1_8v; -}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts new file mode 100644 index 000000000000..d0aaf5750c21 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon-cityman.dts @@ -0,0 +1,15 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Gustave Monce + */ + +/dts-v1/; + +#include "msm8994.dtsi" +#include "msm8994-msft-lumia-octagon.dtsi" + +/ { + model = "Microsoft Lumia 950 XL"; + compatible = "microsoft,cityman", "qcom,msm8994"; +}; diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi similarity index 81% rename from arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts rename to arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 2d989a70e0b5..53628dd5a172 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-cityman.dts +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -1,20 +1,18 @@ // SPDX-License-Identifier: BSD-3-Clause /* + * Common Board Device Tree for + * Microsoft Mobile MSM8994 Octagon Platforms + * * Copyright (c) 2020, Konrad Dybcio + * Copyright (c) 2020, Gustave Monce */ -/dts-v1/; - -#include "msm8994.dtsi" #include "pm8994.dtsi" #include "pmi8994.dtsi" / { - model = "Microsoft Lumia 950 XL"; - compatible = "microsoft,cityman", "qcom,msm8994"; - /* - * Most Lumia 950XL users use GRUB to load their kernels, + * Most Lumia 950/XL users use GRUB to load their kernels, * hence there is no need for msm-id and friends. */ @@ -55,7 +53,7 @@ syna,clip-x-low = <0>; syna,clip-x-high = <1440>; syna,clip-y-low = <0>; - syna,clip-y-high = <2660>; + syna,clip-y-high = <2560>; }; }; }; From 70ad85aa12081d79ec6d4c9deab1dbe48f3b1cb8 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:37 +0100 Subject: [PATCH 523/584] arm64: dts: qcom: msm8994-octagon: Fix up the memory map Windows-based devices have a far different memory map than the standard LA one. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-7-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 166 ++++++++++++++++++ 1 file changed, 166 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 53628dd5a172..eced5cf3e33f 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -10,6 +10,19 @@ #include "pm8994.dtsi" #include "pmi8994.dtsi" +/* + * Delete all generic (msm8994.dtsi) reserved + * memory mappings which are different in this device. + */ +/delete-node/ &adsp_mem; +/delete-node/ &audio_mem; +/delete-node/ &cont_splash_mem; +/delete-node/ &mba_mem; +/delete-node/ &mpss_mem; +/delete-node/ &peripheral_region; +/delete-node/ &rmtfs_mem; +/delete-node/ &smem_mem; + / { /* * Most Lumia 950/XL users use GRUB to load their kernels, @@ -28,6 +41,159 @@ #size-cells = <2>; ranges; }; + + reserved-memory { + /* + * This device being a WP platform has a very different + * memory layout than other Android based devices. + * This memory layout is directly copied from the original + * device UEFI firmware, and adapted based on observations + * using JTAG for the Qualcomm Peripheral Image regions. + */ + + uefi_mem: memory@200000 { + reg = <0 0x200000 0 0x100000>; + no-map; + }; + + mppark_mem: memory@300000 { + reg = <0 0x300000 0 0x80000>; + no-map; + }; + + fbpt_mem: memory@380000 { + reg = <0 0x380000 0 0x1000>; + no-map; + }; + + dbg2_mem: memory@381000 { + reg = <0 0x381000 0 0x4000>; + no-map; + }; + + capsule_mem: memory@385000 { + reg = <0 0x385000 0 0x1000>; + no-map; + }; + + tpmctrl_mem: memory@386000 { + reg = <0 0x386000 0 0x3000>; + no-map; + }; + + uefiinfo_mem: memory@389000 { + reg = <0 0x389000 0 0x1000>; + no-map; + }; + + reset_mem: memory@389000 { + reg = <0 0x389000 0 0x1000>; + no-map; + }; + + resuncached_mem: memory@38e000 { + reg = <0 0x38e000 0 0x72000>; + no-map; + }; + + disp_mem: memory@400000 { + reg = <0 0x400000 0 0x800000>; + no-map; + }; + + uefistack_mem: memory@c00000 { + reg = <0 0xc00000 0 0x40000>; + no-map; + }; + + cpuvect_mem: memory@c40000 { + reg = <0 0xc40000 0 0x10000>; + no-map; + }; + + rescached_mem: memory@400000 { + reg = <0 0xc50000 0 0xb0000>; + no-map; + }; + + tzapps_mem: memory@6500000 { + reg = <0 0x6500000 0 0x500000>; + no-map; + }; + + smem_mem: memory@6a00000 { + reg = <0 0x6a00000 0 0x200000>; + no-map; + }; + + hyp_mem: memory@6c00000 { + reg = <0 0x6c00000 0 0x100000>; + no-map; + }; + + tz_mem: memory@6d00000 { + reg = <0 0x6d00000 0 0x160000>; + no-map; + }; + + rfsa_adsp_mem: memory@6e60000 { + reg = <0 0x6e60000 0 0x10000>; + no-map; + }; + + rfsa_mpss_mem: memory@6e70000 { + compatible = "qcom,rmtfs-mem"; + reg = <0 0x6e70000 0 0x10000>; + no-map; + + qcom,client-id = <1>; + }; + + /* + * Value obtained from the device original ACPI DSDT table + * MPSS_EFS / SBL + */ + mba_mem: memory@6e80000 { + reg = <0 0x6e80000 0 0x180000>; + no-map; + }; + + /* + * Peripheral Image loader region begin! + * The region reserved for pil is 0x7000000-0xef00000 + */ + + mpss_mem: memory@7000000 { + reg = <0 0x7000000 0 0x5a00000>; + no-map; + }; + + adsp_mem: memory@ca00000 { + reg = <0 0xca00000 0 0x1800000>; + no-map; + }; + + venus_mem: memory@e200000 { + reg = <0 0xe200000 0 0x500000>; + no-map; + }; + + pil_metadata_mem: memory@e700000 { + reg = <0 0xe700000 0 0x4000>; + no-map; + }; + + memory@e704000 { + reg = <0 0xe704000 0 0x7fc000>; + no-map; + }; + /* Peripheral Image loader region end */ + + cnss_mem: memory@ef00000 { + reg = <0 0xef00000 0 0x300000>; + no-map; + }; + }; }; &blsp1_i2c1 { From 3c0fd4eba208146504e63a8d6eed476fe26c0f40 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:38 +0100 Subject: [PATCH 524/584] arm64: dts: qcom: msm8994-octagon: Add gpio-keys and Hall sensor This enables tje hardware keys as well as the Hall sensor. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-8-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 77 +++++++++++++++++++ 1 file changed, 77 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index eced5cf3e33f..840bc38a350c 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -9,6 +9,9 @@ #include "pm8994.dtsi" #include "pmi8994.dtsi" +#include +#include +#include /* * Delete all generic (msm8994.dtsi) reserved @@ -42,6 +45,64 @@ ranges; }; + gpio-keys { + compatible = "gpio-keys"; + input-name = "gpio-keys"; + autorepeat; + + volupkey { + label = "Volume Up"; + gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + wakeup-source; + debounce-interval = <15>; + }; + + camsnapkey { + label = "Camera Snapshot"; + gpios = <&pm8994_gpios 4 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + wakeup-source; + debounce-interval = <15>; + }; + + camfocuskey { + label = "Camera Focus"; + gpios = <&pm8994_gpios 5 GPIO_ACTIVE_LOW>; + linux,input-type = <1>; + linux,code = ; + wakeup-source; + debounce-interval = <15>; + }; + }; + + gpio-hall-sensor { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&hall_front_default &hall_back_default>; + + label = "GPIO Hall Effect Sensor"; + + hall-front-sensor { + label = "Hall Effect Front Sensor"; + gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + linux,input-type = ; + linux,code = ; + linux,can-disable; + }; + + hall-back-sensor { + label = "Hall Effect Back Sensor"; + gpios = <&tlmm 75 GPIO_ACTIVE_HIGH>; + linux,input-type = ; + linux,code = ; + linux,can-disable; + }; + }; + reserved-memory { /* * This device being a WP platform has a very different @@ -235,3 +296,19 @@ &sdhc1 { status = "okay"; }; + +&tlmm { + hall_front_default: hall-front-default { + pins = "gpio42"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + hall_back_default: hall-back-default { + pins = "gpio75"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; +}; From 60b214effb80e7592ece7e5fd4370276645bd3a2 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:39 +0100 Subject: [PATCH 525/584] arm64: dts: qcom: msm8994-octagon: Configure regulators Configure the regulators to ensure proper voltages across the board. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-9-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 314 ++++++++++++++++++ 1 file changed, 314 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 840bc38a350c..f89dfc63551a 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -293,6 +293,320 @@ status = "okay"; }; +&pmi8994_spmi_regulators { + vdd_gfx: s2@1700 { + reg = <0x1700 0x100>; + regulator-min-microvolt = <980000>; + regulator-max-microvolt = <980000>; + }; +}; + +&rpm_requests { + /* These values were taken from the original firmware ACPI tables */ + pm8994_regulators: pm8994-regulators { + compatible = "qcom,rpm-pm8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_s2-supply = <&vph_pwr>; + vdd_s3-supply = <&vph_pwr>; + vdd_s4-supply = <&vph_pwr>; + vdd_s5-supply = <&vph_pwr>; + vdd_s6-supply = <&vph_pwr>; + vdd_s7-supply = <&vph_pwr>; + vdd_s8-supply = <&vph_pwr>; + vdd_s9-supply = <&vph_pwr>; + vdd_s10-supply = <&vph_pwr>; + vdd_s11-supply = <&vph_pwr>; + vdd_s12-supply = <&vph_pwr>; + vdd_l1-supply = <&vreg_s1b_1p0>; + vdd_l2_l26_l28-supply = <&vreg_s3a_1p3>; + vdd_l3_l11-supply = <&vreg_s3a_1p3>; + vdd_l4_l27_l31-supply = <&vreg_s3a_1p3>; + vdd_l5_l7-supply = <&vreg_s5a_2p15>; + vdd_l6_l12_l32-supply = <&vreg_s5a_2p15>; + vdd_l8_l16_l30-supply = <&vph_pwr>; + vdd_l9_l10_l18_l22-supply = <&vph_pwr_bbyp>; + vdd_l13_l19_l23_l24-supply = <&vph_pwr_bbyp>; + vdd_l14_l15-supply = <&vreg_s5a_2p15>; + vdd_l17_l29-supply = <&vph_pwr_bbyp>; + vdd_l20_l21-supply = <&vph_pwr_bbyp>; + vdd_l25-supply = <&vreg_s5a_2p15>; + vdd_lvs1_2-supply = <&vreg_s4a_1p8>; + + /* S1, S2, S6 and S12 are managed by RPMPD */ + + vreg_s3a_1p3: s3 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-allow-set-load; + regulator-system-load = <300000>; + }; + + vreg_s4a_1p8: s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-always-on; + regulator-system-load = <325000>; + }; + + vreg_s5a_2p15: s5 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + regulator-allow-set-load; + regulator-system-load = <325000>; + }; + + vreg_s7a_1p0: s7 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + /* + * S8 - SPMI-managed VDD_APC0 + * S9, S10 and S11 (the main one) - SPMI-managed VDD_APC1 + */ + + vreg_l1a_1p0: l1 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l2a_1p25: l2 { + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-allow-set-load; + regulator-system-load = <4160>; + }; + + vreg_l3a_1p2: l3 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l4a_1p225: l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + /* L5 is inaccessible from RPM */ + + vreg_l6a_1p8: l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-allow-set-load; + regulator-system-load = <1000>; + }; + + /* L7 is inaccessible from RPM */ + + vreg_l8a_1p8: l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l9a_1p8: l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l10a_1p8: l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l11a_1p2: l11 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <35000>; + }; + + vreg_l12a_1p8: l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <50000>; + }; + + vreg_l13a_2p95: l13 { + regulator-min-microvolt = <1850000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <22000>; + }; + + vreg_l14a_1p8: l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <52000>; + }; + + vreg_l15a_1p8: l15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_l16a_2p7: l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + vreg_l17a_2p7: l17 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <300000>; + }; + + vreg_l18a_2p85: l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <600000>; + }; + + vreg_l19a_3p3: l19 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <500000>; + }; + + vreg_l20a_2p95: l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-boot-on; + regulator-allow-set-load; + regulator-system-load = <570000>; + }; + + vreg_l21a_2p95: l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <800000>; + }; + + vreg_l22a_3p0: l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <150000>; + }; + + vreg_l23a_2p8: l23 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l24a_3p075: l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3150000>; + regulator-allow-set-load; + regulator-system-load = <5800>; + }; + + vreg_l25a_1p1: l25 { + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l26a_1p0: l26 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + vreg_l27a_1p05: l27 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <500000>; + }; + + vreg_l28a_1p0: l28 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <26000>; + }; + + vreg_l29a_2p8: l29 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <80000>; + }; + + vreg_l30a_1p8: l30 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <2500>; + }; + + vreg_l31a_1p2: l31 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-allow-set-load; + regulator-system-load = <600000>; + }; + + vreg_l32a_1p8: l32 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + vreg_lvs1a_1p8: lvs1 { }; + + vreg_lvs2a_1p8: lvs2 { }; + }; + + pmi8994_regulators: pmi8994-regulators { + compatible = "qcom,rpm-pmi8994-regulators"; + + vdd_s1-supply = <&vph_pwr>; + vdd_bst_byp-supply = <&vph_pwr>; + + vreg_s1b_1p0: s1 { + regulator-min-microvolt = <1025000>; + regulator-max-microvolt = <1025000>; + }; + + /* S2 & S3 - VDD_GFX */ + + vph_pwr_bbyp: boost-bypass { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; +}; + &sdhc1 { status = "okay"; }; From 2eae095fc28c5348de39c421447c84bea8a95367 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:40 +0100 Subject: [PATCH 526/584] arm64: dts: qcom: msm8994-octagon: Add QCA6174 bluetooth Configure and enable QCA6174 Bluetooth and required pins. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-10-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 44 +++++++++++++++++++ 1 file changed, 44 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index f89dfc63551a..1fa152a3d3cb 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -45,6 +45,21 @@ ranges; }; + clocks { + compatible = "simple-bus"; + + divclk4: divclk4 { + compatible = "fixed-clock"; + #clock-cells = <0>; + + clock-frequency = <32768>; + clock-output-names = "divclk4"; + + pinctrl-names = "default"; + pinctrl-0 = <&divclk4_pin_a>; + }; + }; + gpio-keys { compatible = "gpio-keys"; input-name = "gpio-keys"; @@ -291,6 +306,35 @@ &blsp2_uart2 { status = "okay"; + + qca6174_bt: bluetooth { + compatible = "qcom,qca6174-bt"; + + enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>; + clocks = <&divclk4>; + }; +}; + +&pm8994_gpios { + bt_en_gpios: bt_en_gpios { + pinconf { + pins = "gpio19"; + function = PMIC_GPIO_FUNC_NORMAL; + output-low; + power-source = ; + qcom,drive-strength = ; + bias-pull-down; + }; + }; + + divclk4_pin_a: divclk4 { + pinconf { + pins = "gpio18"; + function = PMIC_GPIO_FUNC_FUNC2; + power-source = ; + bias-disable; + }; + }; }; &pmi8994_spmi_regulators { From 600f91111282dae562b93012c0609d38f8b015be Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:41 +0100 Subject: [PATCH 527/584] arm64: dts: qcom: msm8994-octagon: Configure HD3SS460 Type-C mux pins The driver is not available yet, so hardcode the pins. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-11-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 31 +++++++++++++++++++ 1 file changed, 31 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 1fa152a3d3cb..0b8b9e32322a 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -337,6 +337,37 @@ }; }; +&pmi8994_gpios { + pinctrl-0 = <&hd3ss460_pol &hd3ss460_amsel &hd3ss460_en>; + pinctrl-names = "default"; + + /* + * This device uses a TI HD3SS460 Type-C MUX + * As this device has no driver currently, + * the configuration for USB Face Up is set-up here. + * + * TODO: remove once a driver is available + * TODO: add VBUS GPIO 5 + */ + hd3ss460_pol: pol_low { + pins = "gpio8"; + drive-strength = <3>; + bias-pull-down; + }; + + hd3ss460_amsel: amsel_high { + pins = "gpio9"; + drive-strength = <1>; + bias-pull-up; + }; + + hd3ss460_en: en_high { + pins = "gpio10"; + drive-strength = <1>; + bias-pull-up; + }; +}; + &pmi8994_spmi_regulators { vdd_gfx: s2@1700 { reg = <0x1700 0x100>; From 09179fb6aff47bf61db621dde06b51361a8a8f6b Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:42 +0100 Subject: [PATCH 528/584] arm64: dts: qcom: msm8994-octagon: Add uSD card and disable HS400 on eMMC Lumia 950/XL, like other phones, ship with different storage chips. Some of them are not capable of stable operation at HS400. Disable it. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-12-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 21 +++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 0b8b9e32322a..730bd473be6b 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -684,6 +684,27 @@ &sdhc1 { status = "okay"; + + /* + * This device is shipped with HS400 capabable eMMCs + * However various brands have been used in various product batches, + * including a Samsung eMMC (BGND3R) which features a quirk with HS400. + * Set the speed to HS200 as a safety measure. + */ + mmc-hs200-1_8v; +}; + +&sdhc2 { + status = "okay"; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>; + pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>; + + vmmc-supply = <&vreg_l21a_2p95>; + vqmmc-supply = <&vreg_l13a_2p95>; + + cd-gpios = <&pm8994_gpios 8 GPIO_ACTIVE_LOW>; }; &tlmm { From 8b65237e4e1b1c44f7be30bfcc4b61a6ee7f3198 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:43 +0100 Subject: [PATCH 529/584] arm64: dts: qcom: msm8994-octagon: Configure Lattice iCE40 FPGA Octagon devices have a Lattice iCE40 FPGA connected over SPI. Configure it. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-13-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 21 +++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 730bd473be6b..0417c31316d3 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -304,6 +304,27 @@ status = "okay"; }; +&blsp2_spi4 { + status = "okay"; + + /* + * This device is a Lattice UC120 USB-C PD PHY. + * It is actually a Lattice iCE40 FPGA pre-programmed by + * the device firmware with a specific bitstream + * enabling USB Type C PHY functionality. + * Communication is done via a proprietary protocol over SPI. + * + * TODO: Once a proper driver is available, replace this. + */ + uc120: ice5lp2k@0 { + compatible = "lattice,ice40-fpga-mgr"; + reg = <0>; + spi-max-frequency = <5000000>; + cdone-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>; + reset-gpios = <&pmi8994_gpios 4 GPIO_ACTIVE_LOW>; + }; +}; + &blsp2_uart2 { status = "okay"; From da3a82e35e4b24c0392c4667cd7ee1332c0a15e0 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:44 +0100 Subject: [PATCH 530/584] arm64: dts: qcom: msm8994-octagon: Configure PON keys Both the power key and the vol- key are connected over PON. Configure them. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-14-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 16 ++++++++++++++++ arch/arm64/boot/dts/qcom/pm8994.dtsi | 2 +- 2 files changed, 17 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 0417c31316d3..1210b470f00c 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -358,6 +358,22 @@ }; }; +&pm8994_pon { + pwrkey { + compatible = "qcom,pm8941-pwrkey"; + interrupts = <0 8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + linux,code = ; + }; + + volwnkey { + compatible = "qcom,pm8941-resin"; + interrupts = <0 8 1 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + linux,code = ; + }; +}; + &pmi8994_gpios { pinctrl-0 = <&hd3ss460_pol &hd3ss460_amsel &hd3ss460_en>; pinctrl-names = "default"; diff --git a/arch/arm64/boot/dts/qcom/pm8994.dtsi b/arch/arm64/boot/dts/qcom/pm8994.dtsi index 91fff1f209e0..c3876c82c874 100644 --- a/arch/arm64/boot/dts/qcom/pm8994.dtsi +++ b/arch/arm64/boot/dts/qcom/pm8994.dtsi @@ -43,7 +43,7 @@ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; }; - pon@800 { + pm8994_pon: pon@800 { compatible = "qcom,pm8916-pon"; reg = <0x800>; From 7f59caec7b41963efc720dad8e03ba90d930bf86 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sun, 31 Jan 2021 02:38:45 +0100 Subject: [PATCH 531/584] arm64: dts: qcom: msm8994-octagon: Add FM Radio and DDR regulator nodes FAN53526 and SI470X are both connected over blsp2_i2c5. Configure them. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-15-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 26 +++++++++++++++++++ 1 file changed, 26 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 1210b470f00c..b1a09d97b485 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -304,6 +304,32 @@ status = "okay"; }; +&blsp2_i2c5 { + status = "okay"; + + fm_radio: si4705@11 { + compatible = "silabs,si470x"; + reg = <0x11>; + + interrupt-parent = <&tlmm>; + interrupts = <9 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&tlmm 93 GPIO_ACTIVE_HIGH>; + }; + + vreg_lpddr_1p1: fan53526a@6c { + compatible = "fcs,fan53526"; + reg = <0x6c>; + + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + vin-supply = <&vph_pwr>; + fcs,suspend-voltage-selector = <1>; + regulator-always-on; /* Turning off DDR power doesn't sound good. */ + }; + + /* ANX7816 HDMI bridge (needs MDSS HDMI) */ +}; + &blsp2_spi4 { status = "okay"; From 34109bbeccd45f350b70149dcedc1bfbf226ea41 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:46 +0100 Subject: [PATCH 532/584] arm64: dts: qcom: msm8994-octagon: Add NXP NFC node Octagon devices use PN544 connected over I2C. Configure it. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-16-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index b1a09d97b485..86ac180f4893 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -300,6 +300,22 @@ }; }; +&blsp1_i2c6 { + status = "okay"; + + pn547: pn547@28 { + compatible = "nxp,pn544-i2c"; + + reg = <0x28>; + + interrupt-parent = <&tlmm>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + + enable-gpios = <&tlmm 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>; + }; +}; + &blsp1_uart2 { status = "okay"; }; From 3aca45f776e1a908c62a7f52877f94d11197337b Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:47 +0100 Subject: [PATCH 533/584] arm64: dts: qcom: msm8994-octagon: Add sensors on blsp1_i2c5 Add AK09912 magnetometer, ZPA2326 barometer and MPU6500 accelerometer nodes. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-17-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 36 +++++++++++++++++++ 1 file changed, 36 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 86ac180f4893..6b692086e7cf 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -300,6 +300,42 @@ }; }; +&blsp1_i2c5 { + status = "okay"; + + ak09912: magnetometer@c { + compatible = "asahi-kasei,ak09912"; + reg = <0xc>; + + interrupt-parent = <&tlmm>; + interrupts = <26 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vreg_l18a_2p85>; + vid-supply = <&vreg_lvs2a_1p8>; + }; + + zpa2326: barometer@5c { + compatible = "murata,zpa2326"; + reg = <0x5c>; + + interrupt-parent = <&tlmm>; + interrupts = <74 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vreg_lvs2a_1p8>; + }; + + mpu6050: accelerometer@68 { + compatible = "invensense,mpu6500"; + reg = <0x68>; + + interrupt-parent = <&tlmm>; + interrupts = <64 IRQ_TYPE_EDGE_RISING>; + + vdd-supply = <&vreg_lvs2a_1p8>; + vddio-supply = <&vreg_lvs2a_1p8>; + }; +}; + &blsp1_i2c6 { status = "okay"; From caea1f74479dcfa09b4f39d95edc580e67058677 Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:48 +0100 Subject: [PATCH 534/584] arm64: dts: qcom: msm8994-octagon: Add TAS2553 codec Lumia 950/XL feature a TAS2553 codec. Configure it using the TAS2552 driver. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-18-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 20 +++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 6b692086e7cf..76619dee71c7 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -300,6 +300,26 @@ }; }; +&blsp1_i2c2 { + status = "okay"; + + /* + * This device uses the Texas Instruments TAS2553, however the TAS2552 driver + * seems to work here. In the future a proper driver might need to + * be written for this device. + */ + tas2553: tas2553@40 { + compatible = "ti,tas2552"; + reg = <0x40>; + + vbat-supply = <&vph_pwr>; + iovdd-supply = <&vreg_s4a_1p8>; + avdd-supply = <&vreg_s4a_1p8>; + + enable-gpio = <&pm8994_gpios 12 GPIO_ACTIVE_HIGH>; + }; +}; + &blsp1_i2c5 { status = "okay"; From c636eeb751f695ac0481626e6bd0c1c0188740dd Mon Sep 17 00:00:00 2001 From: Gustave Monce Date: Sun, 31 Jan 2021 02:38:49 +0100 Subject: [PATCH 535/584] arm64: dts: qcom: msm8994-octagon: Add AD7147 and APDS9930 sensors Add and configure AD7147 grip sensor and APDS9930 proximity sensor. Signed-off-by: Gustave Monce Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20210131013853.55810-19-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- .../dts/qcom/msm8994-msft-lumia-octagon.dtsi | 50 +++++++++++++++++++ 1 file changed, 50 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi index 76619dee71c7..3a3790a52a2c 100644 --- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi @@ -376,6 +376,42 @@ status = "okay"; }; +&blsp2_i2c1 { + status = "okay"; + + sideinteraction: ad7147_captouch@2c { + compatible = "ad,ad7147_captouch"; + reg = <0x2c>; + + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&grip_default>; + pinctrl-1 = <&grip_sleep>; + + interrupts = <&tlmm 96 IRQ_TYPE_EDGE_FALLING>; + + button_num = <8>; + touchpad_num = <0>; + wheel_num = <0>; + slider_num = <0>; + + vcc-supply = <&vreg_l18a_2p85>; + }; + + /* + * The QPDS-T900/QPDS-T930 is a customized part built for Nokia + * by Avago. It is very similar to the Avago APDS-9930 with some + * minor differences. In the future a proper driver might need to + * be written for this device. For now this works fine. + */ + qpdst900: qpdst900@39 { + compatible = "avago,apds9930"; + reg = <0x39>; + + interrupt-parent = <&tlmm>; + interrupts = <40 IRQ_TYPE_EDGE_FALLING>; + }; +}; + &blsp2_i2c5 { status = "okay"; @@ -843,6 +879,20 @@ }; &tlmm { + grip_default: grip-default { + pins = "gpio39"; + function = "gpio"; + drive-strength = <6>; + bias-pull-down; + }; + + grip_sleep: grip-sleep { + pins = "gpio39"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + hall_front_default: hall-front-default { pins = "gpio42"; function = "gpio"; From fe079442db63a712fb5e66456e6d034d74c156b5 Mon Sep 17 00:00:00 2001 From: Brian Masney Date: Mon, 1 Feb 2021 12:56:54 +0200 Subject: [PATCH 536/584] ARM: dts: qcom: msm8974: add gpu support Add support for the a3xx GPU. opp_table is chosen to include lower frequencies common to all different msm8974 variants. Signed-off-by: Brian Masney [iskren.chernev@gmail.com: change after v1] Signed-off-by: Iskren Chernev Link: https://lore.kernel.org/r/20210201105657.1642825-1-iskren.chernev@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-msm8974.dtsi | 43 ++++++++++++++++++++++++++ arch/arm/boot/dts/qcom-msm8974pro.dtsi | 5 +++ 2 files changed, 48 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 51f5f904f9eb..c65d33591efa 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -1399,6 +1399,49 @@ <&rpmcc RPM_SMD_CNOC_A_CLK>; }; + gpu: adreno@fdb00000 { + status = "disabled"; + + compatible = "qcom,adreno-330.1", + "qcom,adreno"; + reg = <0xfdb00000 0x10000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = ; + interrupt-names = "kgsl_3d0_irq"; + clock-names = "core", + "iface", + "mem_iface"; + clocks = <&mmcc OXILI_GFX3D_CLK>, + <&mmcc OXILICX_AHB_CLK>, + <&mmcc OXILICX_AXI_CLK>; + sram = <&gmu_sram>; + power-domains = <&mmcc OXILICX_GDSC>; + operating-points-v2 = <&gpu_opp_table>; + + interconnects = <&mmssnoc MNOC_MAS_GRAPHICS_3D &bimc BIMC_SLV_EBI_CH0>, + <&ocmemnoc OCMEM_VNOC_MAS_GFX3D &ocmemnoc OCMEM_SLV_OCMEM>; + interconnect-names = "gfx-mem", + "ocmem"; + + // iommus = <&gpu_iommu 0>; + + gpu_opp_table: opp_table { + compatible = "operating-points-v2"; + + opp-320000000 { + opp-hz = /bits/ 64 <320000000>; + }; + + opp-200000000 { + opp-hz = /bits/ 64 <200000000>; + }; + + opp-27000000 { + opp-hz = /bits/ 64 <27000000>; + }; + }; + }; + mdss: mdss@fd900000 { status = "disabled"; diff --git a/arch/arm/boot/dts/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom-msm8974pro.dtsi index 6740a4cb7da8..b64c28036dd0 100644 --- a/arch/arm/boot/dts/qcom-msm8974pro.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974pro.dtsi @@ -14,5 +14,10 @@ clock-controller@fc400000 { compatible = "qcom,gcc-msm8974pro"; }; + + adreno@fdb00000 { + compatible = "qcom,adreno-330.2", + "qcom,adreno"; + }; }; }; From 4389eeac4867d0fd906cdaf17bf84d4a8681f59c Mon Sep 17 00:00:00 2001 From: Samuel Pascua Date: Mon, 1 Feb 2021 12:56:55 +0200 Subject: [PATCH 537/584] ARM: dts: qcom: msm8974-klte: add support for GPU Enable adreno dt node. Signed-off-by: Samuel Pascua [iskren.chernev@gmail.com: changes after v1] Signed-off-by: Iskren Chernev Link: https://lore.kernel.org/r/20210201105657.1642825-2-iskren.chernev@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts index 3929c9435e29..86be4ae743f4 100644 --- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts +++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts @@ -697,6 +697,10 @@ pinctrl-0 = <&fuelgauge_pin>; }; }; + + adreno@fdb00000 { + status = "ok"; + }; }; &spmi_bus { From 3657b677d20d4b6bda441bd568d037446bd6d880 Mon Sep 17 00:00:00 2001 From: Samuel Pascua Date: Mon, 1 Feb 2021 12:56:56 +0200 Subject: [PATCH 538/584] ARM: dts: qcom: msm8974-klte: add support for display Add initial support for the display found on the Samsung Galaxy 5 (klte) phone. This is based on work from Jonathan Marek & Brian Masney. Signed-off-by: Samuel Pascua [iskren.chernev@gmail.com: add reset gpio, regulators] Signed-off-by: Iskren Chernev Link: https://lore.kernel.org/r/20210201105657.1642825-3-iskren.chernev@gmail.com Signed-off-by: Bjorn Andersson --- .../boot/dts/qcom-msm8974-samsung-klte.dts | 95 +++++++++++++++++++ 1 file changed, 95 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts index 86be4ae743f4..d042c7cbab71 100644 --- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts +++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts @@ -298,6 +298,20 @@ enable-active-high; }; + vreg_panel: panel-regulator { + compatible = "regulator-fixed"; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_en_pin>; + + regulator-name = "panel-vddr-reg"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + + gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + /delete-node/ vreg-boost; }; @@ -453,6 +467,16 @@ bias-pull-down; }; }; + + panel_te_pin: panel { + te { + pins = "gpio12"; + function = "mdp_vsync"; + + drive-strength = <2>; + bias-disable; + }; + }; }; sdhc_1: sdhci@f9824900 { @@ -701,6 +725,60 @@ adreno@fdb00000 { status = "ok"; }; + + mdss@fd900000 { + status = "ok"; + + mdp@fd900000 { + status = "ok"; + }; + + dsi@fd922800 { + status = "ok"; + + vdda-supply = <&pma8084_l2>; + vdd-supply = <&pma8084_l22>; + vddio-supply = <&pma8084_l12>; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + port@1 { + endpoint { + remote-endpoint = <&panel_in>; + data-lanes = <0 1 2 3>; + }; + }; + }; + + panel: panel@0 { + reg = <0>; + compatible = "samsung,s6e3fa2"; + + pinctrl-names = "default"; + pinctrl-0 = <&panel_te_pin &panel_rst_pin>; + + iovdd-supply = <&pma8084_lvs4>; + vddr-supply = <&vreg_panel>; + + reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>; + te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>; + + port { + panel_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + }; + }; + + dsi-phy@fd922a00 { + status = "ok"; + + vddio-supply = <&pma8084_l12>; + }; + }; }; &spmi_bus { @@ -730,6 +808,14 @@ power-source = ; }; + panel_en_pin: panel-en-pin { + pins = "gpio14"; + function = "normal"; + bias-pull-up; + power-source = ; + qcom,drive-strength = ; + }; + wlan_sleep_clk_pin: wlan-sleep-clk-pin { pins = "gpio16"; function = "func2"; @@ -739,6 +825,15 @@ qcom,drive-strength = ; }; + panel_rst_pin: panel-rst-pin { + pins = "gpio17"; + function = "normal"; + bias-disable; + power-source = ; + qcom,drive-strength = ; + }; + + fuelgauge_pin: fuelgauge-int-pin { pins = "gpio21"; function = "normal"; From 9d1ee210ab8ae610285e5d6db9ea47491fce6dc6 Mon Sep 17 00:00:00 2001 From: Iskren Chernev Date: Mon, 1 Feb 2021 12:56:57 +0200 Subject: [PATCH 539/584] ARM: dts: qcom: msm8974-klte: Mark essential regulators s1 and l12 regulators are used for the memory and cache on the Samsung S5 (klte). If they are turned off the phone shuts down. So mark them as always-on to prevent that from happening. Signed-off-by: Iskren Chernev Tested-by: Alexey Minnekhanov Link: https://lore.kernel.org/r/20210201105657.1642825-4-iskren.chernev@gmail.com Signed-off-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts index d042c7cbab71..a0f7f461f48c 100644 --- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts +++ b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts @@ -30,6 +30,7 @@ pma8084_s1: s1 { regulator-min-microvolt = <675000>; regulator-max-microvolt = <1050000>; + regulator-always-on; }; pma8084_s2: s2 { @@ -115,6 +116,7 @@ pma8084_l12: l12 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; + regulator-always-on; }; pma8084_l13: l13 { From d5ae2528b0b56cf054b27d48b0cb85330900082f Mon Sep 17 00:00:00 2001 From: Vincent Knecht Date: Sat, 23 Jan 2021 11:44:16 +0100 Subject: [PATCH 540/584] arm64: dts: msm8916: Fix reserved and rfsa nodes unit address Fix `reserved` and `rfsa` unit address according to their reg address Fixes: 7258e10e6a0b ("ARM: dts: msm8916: Update reserved-memory") Signed-off-by: Vincent Knecht Link: https://lore.kernel.org/r/20210123104417.518105-1-vincent.knecht@mailoo.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8916.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi index c82ac0521e0c..5353da521974 100644 --- a/arch/arm64/boot/dts/qcom/msm8916.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi @@ -56,7 +56,7 @@ no-map; }; - reserved@8668000 { + reserved@86680000 { reg = <0x0 0x86680000 0x0 0x80000>; no-map; }; @@ -69,7 +69,7 @@ qcom,client-id = <1>; }; - rfsa@867e00000 { + rfsa@867e0000 { reg = <0x0 0x867e0000 0x0 0x20000>; no-map; }; From 03e6cb3d8af79ff9a4a1b9fecf3866887bfa6465 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sat, 9 Jan 2021 17:29:55 +0100 Subject: [PATCH 541/584] arm64: dts: qcom: msm8998: Merge in msm8998-pins.dtsi to msm8998.dtsi This is the usual way of handling pin configuration upstream now, so align to it. Signed-off-by: Konrad Dybcio Tested-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20210109163001.146867-2-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998-pins.dtsi | 108 --------------------- arch/arm64/boot/dts/qcom/msm8998.dtsi | 106 +++++++++++++++++++- 2 files changed, 104 insertions(+), 110 deletions(-) delete mode 100644 arch/arm64/boot/dts/qcom/msm8998-pins.dtsi diff --git a/arch/arm64/boot/dts/qcom/msm8998-pins.dtsi b/arch/arm64/boot/dts/qcom/msm8998-pins.dtsi deleted file mode 100644 index 7c222cbf19d9..000000000000 --- a/arch/arm64/boot/dts/qcom/msm8998-pins.dtsi +++ /dev/null @@ -1,108 +0,0 @@ -// SPDX-License-Identifier: GPL-2.0 -/* Copyright (c) 2018, The Linux Foundation. All rights reserved. */ - -&tlmm { - sdc2_clk_on: sdc2_clk_on { - config { - pins = "sdc2_clk"; - bias-disable; /* NO pull */ - drive-strength = <16>; /* 16 mA */ - }; - }; - - sdc2_clk_off: sdc2_clk_off { - config { - pins = "sdc2_clk"; - bias-disable; /* NO pull */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_cmd_on: sdc2_cmd_on { - config { - pins = "sdc2_cmd"; - bias-pull-up; /* pull up */ - drive-strength = <10>; /* 10 mA */ - }; - }; - - sdc2_cmd_off: sdc2_cmd_off { - config { - pins = "sdc2_cmd"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_data_on: sdc2_data_on { - config { - pins = "sdc2_data"; - bias-pull-up; /* pull up */ - drive-strength = <10>; /* 10 mA */ - }; - }; - - sdc2_data_off: sdc2_data_off { - config { - pins = "sdc2_data"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_cd_on: sdc2_cd_on { - mux { - pins = "gpio95"; - function = "gpio"; - }; - - config { - pins = "gpio95"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - sdc2_cd_off: sdc2_cd_off { - mux { - pins = "gpio95"; - function = "gpio"; - }; - - config { - pins = "gpio95"; - bias-pull-up; /* pull up */ - drive-strength = <2>; /* 2 mA */ - }; - }; - - blsp1_uart3_on: blsp1_uart3_on { - tx { - pins = "gpio45"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - - rx { - pins = "gpio46"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - - cts { - pins = "gpio47"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - - rfr { - pins = "gpio48"; - function = "blsp_uart3_a"; - drive-strength = <2>; - bias-disable; - }; - }; -}; diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index ebdaaf1dfca4..699bd67efcd0 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -1073,6 +1073,110 @@ #gpio-cells = <0x2>; interrupt-controller; #interrupt-cells = <0x2>; + + sdc2_clk_on: sdc2_clk_on { + config { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <16>; + }; + }; + + sdc2_clk_off: sdc2_clk_off { + config { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + }; + + sdc2_cmd_on: sdc2_cmd_on { + config { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + }; + + sdc2_cmd_off: sdc2_cmd_off { + config { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_data_on: sdc2_data_on { + config { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + }; + + sdc2_data_off: sdc2_data_off { + config { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_cd_on: sdc2_cd_on { + mux { + pins = "gpio95"; + function = "gpio"; + }; + + config { + pins = "gpio95"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + sdc2_cd_off: sdc2_cd_off { + mux { + pins = "gpio95"; + function = "gpio"; + }; + + config { + pins = "gpio95"; + bias-pull-up; + drive-strength = <2>; + }; + }; + + blsp1_uart3_on: blsp1_uart3_on { + tx { + pins = "gpio45"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + + rx { + pins = "gpio46"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + + cts { + pins = "gpio47"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + + rfr { + pins = "gpio48"; + function = "blsp_uart3_a"; + drive-strength = <2>; + bias-disable; + }; + }; }; remoteproc_mss: remoteproc@4080000 { @@ -2110,5 +2214,3 @@ }; }; }; - -#include "msm8998-pins.dtsi" From 6845359eea47afed5fa81571a526418228b93580 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sat, 9 Jan 2021 17:29:56 +0100 Subject: [PATCH 542/584] arm64: dts: qcom: msm8998: Add DMA to I2C hosts Add DMA properties to I2C hosts to allow for DMA transfers. Signed-off-by: Konrad Dybcio Tested-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20210109163001.146867-3-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998.dtsi | 37 +++++++++++++++++++++++++++ 1 file changed, 37 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index 699bd67efcd0..eadac13ff975 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -1893,6 +1893,8 @@ clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -1908,6 +1910,8 @@ clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -1923,6 +1927,8 @@ clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -1938,6 +1944,8 @@ clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -1953,6 +1961,8 @@ clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 14>, <&blsp1_dma 15>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -1968,6 +1978,8 @@ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp1_dma 16>, <&blsp1_dma 17>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -1975,6 +1987,19 @@ #size-cells = <0>; }; + blsp2_dma: dma@c184000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x0c184000 0x25000>; + interrupts = ; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + qcom,controlled-remotely; + num-channels = <18>; + qcom,num-ees = <4>; + }; + blsp2_uart1: serial@c1b0000 { compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; reg = <0x0c1b0000 0x1000>; @@ -1993,6 +2018,8 @@ clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -2008,6 +2035,8 @@ clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 8>, <&blsp2_dma 9>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -2023,6 +2052,8 @@ clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -2038,6 +2069,8 @@ clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 12>, <&blsp2_dma 13>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -2053,6 +2086,8 @@ clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 14>, <&blsp2_dma 15>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; @@ -2068,6 +2103,8 @@ clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>; clock-names = "core", "iface"; + dmas = <&blsp2_dma 16>, <&blsp2_dma 17>; + dma-names = "tx", "rx"; clock-frequency = <400000>; status = "disabled"; From 0fee55fc0de71bcb68e1c2cc1c171c3576da7568 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sat, 9 Jan 2021 17:29:57 +0100 Subject: [PATCH 543/584] arm64: dts: qcom: msm8998: Add I2C pinctrl and fix BLSP2_I2C naming The BLSP2-connected interfaces started from 0 which is.. misleading to say the least.. the clock names corresponding to these started from 1, so let's align to that so as to reduce confusion. Signed-off-by: Konrad Dybcio Tested-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20210109163001.146867-4-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998.dtsi | 216 +++++++++++++++++++++++++- 1 file changed, 210 insertions(+), 6 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index eadac13ff975..c7d6dbd24f1e 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -1177,6 +1177,174 @@ bias-disable; }; }; + + blsp1_i2c1_default: blsp1-i2c1-default { + pins = "gpio2", "gpio3"; + function = "blsp_i2c1"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c1_sleep: blsp1-i2c1-sleep { + pins = "gpio2", "gpio3"; + function = "blsp_i2c1"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c2_default: blsp1-i2c2-default { + pins = "gpio32", "gpio33"; + function = "blsp_i2c2"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c2_sleep: blsp1-i2c2-sleep { + pins = "gpio32", "gpio33"; + function = "blsp_i2c2"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c3_default: blsp1-i2c3-default { + pins = "gpio47", "gpio48"; + function = "blsp_i2c3"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c3_sleep: blsp1-i2c3-sleep { + pins = "gpio47", "gpio48"; + function = "blsp_i2c3"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c4_default: blsp1-i2c4-default { + pins = "gpio10", "gpio11"; + function = "blsp_i2c4"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c4_sleep: blsp1-i2c4-sleep { + pins = "gpio10", "gpio11"; + function = "blsp_i2c4"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c5_default: blsp1-i2c5-default { + pins = "gpio87", "gpio88"; + function = "blsp_i2c5"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c5_sleep: blsp1-i2c5-sleep { + pins = "gpio87", "gpio88"; + function = "blsp_i2c5"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp1_i2c6_default: blsp1-i2c6-default { + pins = "gpio43", "gpio44"; + function = "blsp_i2c6"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c6_sleep: blsp1-i2c6-sleep { + pins = "gpio43", "gpio44"; + function = "blsp_i2c6"; + drive-strength = <2>; + bias-pull-up; + }; + /* 6 interfaces per QUP, BLSP2 indexes are numbered (n)+6 */ + blsp2_i2c1_default: blsp2-i2c1-default { + pins = "gpio55", "gpio56"; + function = "blsp_i2c7"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c1_sleep: blsp2-i2c1-sleep { + pins = "gpio55", "gpio56"; + function = "blsp_i2c7"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c2_default: blsp2-i2c2-default { + pins = "gpio6", "gpio7"; + function = "blsp_i2c8"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c2_sleep: blsp2-i2c2-sleep { + pins = "gpio6", "gpio7"; + function = "blsp_i2c8"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c3_default: blsp2-i2c3-default { + pins = "gpio51", "gpio52"; + function = "blsp_i2c9"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c3_sleep: blsp2-i2c3-sleep { + pins = "gpio51", "gpio52"; + function = "blsp_i2c9"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c4_default: blsp2-i2c4-default { + pins = "gpio67", "gpio68"; + function = "blsp_i2c10"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c4_sleep: blsp2-i2c4-sleep { + pins = "gpio67", "gpio68"; + function = "blsp_i2c10"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c5_default: blsp2-i2c5-default { + pins = "gpio60", "gpio61"; + function = "blsp_i2c11"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c5_sleep: blsp2-i2c5-sleep { + pins = "gpio60", "gpio61"; + function = "blsp_i2c11"; + drive-strength = <2>; + bias-pull-up; + }; + + blsp2_i2c6_default: blsp2-i2c6-default { + pins = "gpio83", "gpio84"; + function = "blsp_i2c12"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c6_sleep: blsp2-i2c6-sleep { + pins = "gpio83", "gpio84"; + function = "blsp_i2c12"; + drive-strength = <2>; + bias-pull-up; + }; }; remoteproc_mss: remoteproc@4080000 { @@ -1895,6 +2063,9 @@ clock-names = "core", "iface"; dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c1_default>; + pinctrl-1 = <&blsp1_i2c1_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1912,6 +2083,9 @@ clock-names = "core", "iface"; dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c2_default>; + pinctrl-1 = <&blsp1_i2c2_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1929,6 +2103,9 @@ clock-names = "core", "iface"; dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c3_default>; + pinctrl-1 = <&blsp1_i2c3_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1946,6 +2123,9 @@ clock-names = "core", "iface"; dmas = <&blsp1_dma 12>, <&blsp1_dma 13>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c4_default>; + pinctrl-1 = <&blsp1_i2c4_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1963,6 +2143,9 @@ clock-names = "core", "iface"; dmas = <&blsp1_dma 14>, <&blsp1_dma 15>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c5_default>; + pinctrl-1 = <&blsp1_i2c5_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -1980,6 +2163,9 @@ clock-names = "core", "iface"; dmas = <&blsp1_dma 16>, <&blsp1_dma 17>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp1_i2c6_default>; + pinctrl-1 = <&blsp1_i2c6_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2010,7 +2196,7 @@ status = "disabled"; }; - blsp2_i2c0: i2c@c1b5000 { + blsp2_i2c1: i2c@c1b5000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b5000 0x600>; interrupts = ; @@ -2020,6 +2206,9 @@ clock-names = "core", "iface"; dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c1_default>; + pinctrl-1 = <&blsp2_i2c1_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2027,7 +2216,7 @@ #size-cells = <0>; }; - blsp2_i2c1: i2c@c1b6000 { + blsp2_i2c2: i2c@c1b6000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b6000 0x600>; interrupts = ; @@ -2037,6 +2226,9 @@ clock-names = "core", "iface"; dmas = <&blsp2_dma 8>, <&blsp2_dma 9>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c2_default>; + pinctrl-1 = <&blsp2_i2c2_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2044,7 +2236,7 @@ #size-cells = <0>; }; - blsp2_i2c2: i2c@c1b7000 { + blsp2_i2c3: i2c@c1b7000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b7000 0x600>; interrupts = ; @@ -2054,6 +2246,9 @@ clock-names = "core", "iface"; dmas = <&blsp2_dma 10>, <&blsp2_dma 11>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c3_default>; + pinctrl-1 = <&blsp2_i2c3_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2061,7 +2256,7 @@ #size-cells = <0>; }; - blsp2_i2c3: i2c@c1b8000 { + blsp2_i2c4: i2c@c1b8000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b8000 0x600>; interrupts = ; @@ -2071,6 +2266,9 @@ clock-names = "core", "iface"; dmas = <&blsp2_dma 12>, <&blsp2_dma 13>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c4_default>; + pinctrl-1 = <&blsp2_i2c4_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2078,7 +2276,7 @@ #size-cells = <0>; }; - blsp2_i2c4: i2c@c1b9000 { + blsp2_i2c5: i2c@c1b9000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1b9000 0x600>; interrupts = ; @@ -2088,6 +2286,9 @@ clock-names = "core", "iface"; dmas = <&blsp2_dma 14>, <&blsp2_dma 15>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c5_default>; + pinctrl-1 = <&blsp2_i2c5_sleep>; clock-frequency = <400000>; status = "disabled"; @@ -2095,7 +2296,7 @@ #size-cells = <0>; }; - blsp2_i2c5: i2c@c1ba000 { + blsp2_i2c6: i2c@c1ba000 { compatible = "qcom,i2c-qup-v2.2.1"; reg = <0x0c1ba000 0x600>; interrupts = ; @@ -2105,6 +2306,9 @@ clock-names = "core", "iface"; dmas = <&blsp2_dma 16>, <&blsp2_dma 17>; dma-names = "tx", "rx"; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <&blsp2_i2c6_default>; + pinctrl-1 = <&blsp2_i2c6_sleep>; clock-frequency = <400000>; status = "disabled"; From c43cfc549fdb870857d58063b6268f083b132b48 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sat, 9 Jan 2021 17:29:58 +0100 Subject: [PATCH 544/584] arm64: dts: qcom: msm8998: Add capacity-dmips-mhz to CPU cores Add capacity-dmips-mhz to ensure the scheduler can efficiently make use of the big.LITTLE core configuration. Signed-off-by: Konrad Dybcio Tested-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20210109163001.146867-5-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index c7d6dbd24f1e..b2481043205a 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -133,6 +133,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x0>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L2_0: l2-cache { @@ -152,6 +153,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x1>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L1_I_1: l1-icache { @@ -167,6 +169,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x2>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L1_I_2: l1-icache { @@ -182,6 +185,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x3>; enable-method = "psci"; + capacity-dmips-mhz = <1024>; cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>; next-level-cache = <&L2_0>; L1_I_3: l1-icache { @@ -197,6 +201,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x100>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L2_1: l2-cache { @@ -216,6 +221,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x101>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L1_I_101: l1-icache { @@ -231,6 +237,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x102>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L1_I_102: l1-icache { @@ -246,6 +253,7 @@ compatible = "qcom,kryo280"; reg = <0x0 0x103>; enable-method = "psci"; + capacity-dmips-mhz = <1536>; cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>; next-level-cache = <&L2_1>; L1_I_103: l1-icache { From a72848e8a4d761dccddf6af93e8248384986928f Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Sat, 9 Jan 2021 17:29:59 +0100 Subject: [PATCH 545/584] arm64: dts: qcom: msm8998: Disable some components by default Some components (like PCIe) are not used on all devices and with a certain firmware configuration they might end up triggering a force reboot or a Synchronous Abort. This commit brings no functional difference as the nodes are enabled on devices which didn't disable them previously. Signed-off-by: Konrad Dybcio Tested-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20210109163001.146867-6-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi | 16 ++++++++++++++++ arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi | 10 ++++++++++ arch/arm64/boot/dts/qcom/msm8998.dtsi | 6 +++++- 3 files changed, 31 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi index 00d84fb21798..b500f24d47bc 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi @@ -74,6 +74,14 @@ cpu-idle-states = <&BIG_CPU_SLEEP_1>; }; +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + &pm8005_lsid1 { pm8005-regulators { compatible = "qcom,pm8005-regulators"; @@ -295,6 +303,14 @@ pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; }; +&ufshc { + status = "okay"; +}; + +&ufsphy { + status = "okay"; +}; + &usb3 { status = "okay"; }; diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi index cec42437b302..c1ef0c71d5f5 100644 --- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi @@ -106,6 +106,14 @@ // status = "okay"; }; +&pcie0 { + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + &pm8005_lsid1 { pm8005-regulators { compatible = "qcom,pm8005-regulators"; @@ -345,6 +353,7 @@ }; &ufshc { + status = "okay"; vcc-supply = <&vreg_l20a_2p95>; vccq-supply = <&vreg_l26a_1p2>; vccq2-supply = <&vreg_s4a_1p8>; @@ -354,6 +363,7 @@ }; &ufsphy { + status = "okay"; vdda-phy-supply = <&vreg_l1a_0p875>; vdda-pll-supply = <&vreg_l2a_1p2>; vddp-ref-clk-supply = <&vreg_l26a_1p2>; diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index b2481043205a..65c87a8be5a2 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -945,6 +945,7 @@ num-lanes = <1>; phys = <&pciephy>; phy-names = "pciephy"; + status = "disabled"; ranges = <0x01000000 0x0 0x1b200000 0x1b200000 0x0 0x100000>, <0x02000000 0x0 0x1b300000 0x1b300000 0x0 0xd00000>; @@ -970,11 +971,12 @@ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>; }; - phy@1c06000 { + pcie_phy: phy@1c06000 { compatible = "qcom,msm8998-qmp-pcie-phy"; reg = <0x01c06000 0x18c>; #address-cells = <1>; #size-cells = <1>; + status = "disabled"; ranges; clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, @@ -1007,6 +1009,7 @@ phy-names = "ufsphy"; lanes-per-direction = <2>; power-domains = <&gcc UFS_GDSC>; + status = "disabled"; #reset-cells = <1>; clock-names = @@ -1046,6 +1049,7 @@ reg = <0x01da7000 0x18c>; #address-cells = <1>; #size-cells = <1>; + status = "disabled"; ranges; clock-names = From 20fd3b37285b02952b1e843281506db4512803bb Mon Sep 17 00:00:00 2001 From: Akhil P Oommen Date: Fri, 8 Jan 2021 23:45:31 +0530 Subject: [PATCH 546/584] arm64: dts: qcom: sc7180: Add support for gpu fuse Add support for gpu fuse to help identify the supported opps. Signed-off-by: Akhil P Oommen Link: https://lore.kernel.org/r/1610129731-4875-2-git-send-email-akhilpo@codeaurora.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/sc7180.dtsi | 22 ++++++++++++++++++++++ 1 file changed, 22 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi index 04445cd3cfd9..284e0f7bea84 100644 --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi @@ -682,6 +682,11 @@ reg = <0x25b 0x1>; bits = <1 3>; }; + + gpu_speed_bin: gpu_speed_bin@1d2 { + reg = <0x1d2 0x2>; + bits = <5 8>; + }; }; sdhc_1: sdhci@7c4000 { @@ -2054,52 +2059,69 @@ #cooling-cells = <2>; + nvmem-cells = <&gpu_speed_bin>; + nvmem-cell-names = "speed_bin"; + interconnects = <&gem_noc MASTER_GFX3D 0 &mc_virt SLAVE_EBI1 0>; interconnect-names = "gfx-mem"; gpu_opp_table: opp-table { compatible = "operating-points-v2"; + opp-825000000 { + opp-hz = /bits/ 64 <825000000>; + opp-level = ; + opp-peak-kBps = <8532000>; + opp-supported-hw = <0x04>; + }; + opp-800000000 { opp-hz = /bits/ 64 <800000000>; opp-level = ; opp-peak-kBps = <8532000>; + opp-supported-hw = <0x07>; }; opp-650000000 { opp-hz = /bits/ 64 <650000000>; opp-level = ; opp-peak-kBps = <7216000>; + opp-supported-hw = <0x07>; }; opp-565000000 { opp-hz = /bits/ 64 <565000000>; opp-level = ; opp-peak-kBps = <5412000>; + opp-supported-hw = <0x07>; }; opp-430000000 { opp-hz = /bits/ 64 <430000000>; opp-level = ; opp-peak-kBps = <5412000>; + opp-supported-hw = <0x07>; }; opp-355000000 { opp-hz = /bits/ 64 <355000000>; opp-level = ; opp-peak-kBps = <3072000>; + opp-supported-hw = <0x07>; }; opp-267000000 { opp-hz = /bits/ 64 <267000000>; opp-level = ; opp-peak-kBps = <3072000>; + opp-supported-hw = <0x07>; }; opp-180000000 { opp-hz = /bits/ 64 <180000000>; opp-level = ; opp-peak-kBps = <1804000>; + opp-supported-hw = <0x07>; }; }; }; From 564f18f03e91aa770f4ffccf2fee78d61216a4f4 Mon Sep 17 00:00:00 2001 From: Konrad Dybcio Date: Thu, 24 Dec 2020 13:00:25 +0100 Subject: [PATCH 547/584] arm64: dts: qcom: msm8996: Add missing device_type under pcie[01] Signed-off-by: Konrad Dybcio Link: https://lore.kernel.org/r/20201224120025.6282-1-konrad.dybcio@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8996.dtsi | 4 ++++ 1 file changed, 4 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi index 7eef07e73e25..ce430ba9c118 100644 --- a/arch/arm64/boot/dts/qcom/msm8996.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi @@ -750,6 +750,8 @@ ranges = <0x01000000 0x0 0x0c200000 0x0c200000 0x0 0x100000>, <0x02000000 0x0 0x0c300000 0x0c300000 0x0 0xd00000>; + device_type = "pci"; + interrupts = ; interrupt-names = "msi"; #interrupt-cells = <1>; @@ -802,6 +804,8 @@ ranges = <0x01000000 0x0 0x0d200000 0x0d200000 0x0 0x100000>, <0x02000000 0x0 0x0d300000 0x0d300000 0x0 0xd00000>; + device_type = "pci"; + interrupts = ; interrupt-names = "msi"; #interrupt-cells = <1>; From 7790114893c537176ebab62d002a261b5f01f7a9 Mon Sep 17 00:00:00 2001 From: AngeloGioacchino Del Regno Date: Sat, 9 Jan 2021 17:07:59 +0100 Subject: [PATCH 548/584] arm64: dts: qcom: msm8998: Use rpmpd definitions for opp table levels The dt-bindings/power/qcom-rpmpd.h header is being included in this DT but the RPMPD OPP table declarations were using open-coded values: use the definitions found in the aforementioned header. Signed-off-by: AngeloGioacchino Del Regno Link: https://lore.kernel.org/r/20210109160759.186990-1-angelogioacchino.delregno@somainline.org Signed-off-by: Bjorn Andersson --- arch/arm64/boot/dts/qcom/msm8998.dtsi | 20 ++++++++++---------- 1 file changed, 10 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi index 65c87a8be5a2..1f2e93aa6553 100644 --- a/arch/arm64/boot/dts/qcom/msm8998.dtsi +++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi @@ -387,43 +387,43 @@ compatible = "operating-points-v2"; rpmpd_opp_ret: opp1 { - opp-level = <16>; + opp-level = ; }; rpmpd_opp_ret_plus: opp2 { - opp-level = <32>; + opp-level = ; }; rpmpd_opp_min_svs: opp3 { - opp-level = <48>; + opp-level = ; }; rpmpd_opp_low_svs: opp4 { - opp-level = <64>; + opp-level = ; }; rpmpd_opp_svs: opp5 { - opp-level = <128>; + opp-level = ; }; rpmpd_opp_svs_plus: opp6 { - opp-level = <192>; + opp-level = ; }; rpmpd_opp_nom: opp7 { - opp-level = <256>; + opp-level = ; }; rpmpd_opp_nom_plus: opp8 { - opp-level = <320>; + opp-level = ; }; rpmpd_opp_turbo: opp9 { - opp-level = <384>; + opp-level = ; }; rpmpd_opp_turbo_plus: opp10 { - opp-level = <512>; + opp-level = ; }; }; }; From b6e3ff418579f940ca46eafc38207e9b0f5ec9be Mon Sep 17 00:00:00 2001 From: Jerome Brunet Date: Mon, 7 Dec 2020 10:53:45 +0100 Subject: [PATCH 549/584] arm64: dts: meson: vim3: whitespace fixups Spaces have been used to indent 2 nodes. Replace those with tabs and remove one extra newline Signed-off-by: Jerome Brunet Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20201207095346.26297-2-jbrunet@baylibre.com --- .../boot/dts/amlogic/meson-khadas-vim3.dtsi | 19 +++++++++---------- 1 file changed, 9 insertions(+), 10 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi index 8f8656262ae7..d3b25163b421 100644 --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi @@ -283,12 +283,12 @@ }; ðmac { - pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&external_phy>; - amlogic,tx-delay-ns = <2>; + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; }; &frddr_a { @@ -354,9 +354,9 @@ }; &pwm_ef { - status = "okay"; - pinctrl-0 = <&pwm_e_pins>; - pinctrl-names = "default"; + status = "okay"; + pinctrl-0 = <&pwm_e_pins>; + pinctrl-names = "default"; }; &saradc { @@ -450,7 +450,6 @@ }; }; - &tdmif_a { status = "okay"; }; From a74978f34270f724369d8f84666ea0c361d3a699 Mon Sep 17 00:00:00 2001 From: Alexander Dahl Date: Mon, 28 Dec 2020 17:32:17 +0100 Subject: [PATCH 550/584] arm64: dts: meson: Fix schema warnings for pwm-leds The node names for devices using the pwm-leds driver follow a certain naming scheme (now). Parent node name is not enforced, but recommended by DT project. Signed-off-by: Alexander Dahl Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20201228163217.32520-5-post@lespocky.de --- .../arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts | 4 ++-- arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 4 ++-- arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts | 8 ++++---- 3 files changed, 8 insertions(+), 8 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts index 6fe589cd2ba2..45adae480a3d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts @@ -42,10 +42,10 @@ }; }; - pwmleds { + led-controller { compatible = "pwm-leds"; - power { + led-1 { label = "vim:red:power"; pwms = <&pwm_AO_ab 1 7812500 0>; max-brightness = <255>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts index bf9877d33427..25857e0c0831 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts @@ -81,10 +81,10 @@ }; }; - pwmleds { + led-controller { compatible = "pwm-leds"; - power { + led-1 { label = "vim:red:power"; pwms = <&pwm_AO_ab 1 7812500 0>; max-brightness = <255>; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts index 5ab139a34c01..039a8d0d1e9b 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts @@ -101,20 +101,20 @@ }; }; - leds { + led-controller-1 { compatible = "gpio-leds"; - led-bluetooth { + led-1 { label = "sei610:blue:bt"; gpios = <&gpio GPIOC_7 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>; default-state = "off"; }; }; - pwmleds { + led-controller-2 { compatible = "pwm-leds"; - power { + led-2 { label = "sei610:red:power"; pwms = <&pwm_AO_ab 0 30518 0>; max-brightness = <255>; From fc4aa3804ec78a726f235b7f3440ba8034e9d88e Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Tue, 19 Jan 2021 14:57:33 +0000 Subject: [PATCH 551/584] dt-bindings: arm: amlogic: add support for the Beelink GS-King-X The Shenzen AZW (Beelink) GS-King-X is based on the Amlogic W400 reference board with an S922X-H chip. Signed-off-by: Christian Hewitt Acked-by: Rob Herring Reviewed-by: Martin Blumenstingl Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210119145734.12675-2-christianshewitt@gmail.com --- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml index 3341788d1096..6bef60ddda64 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.yaml +++ b/Documentation/devicetree/bindings/arm/amlogic.yaml @@ -151,6 +151,7 @@ properties: - description: Boards with the Amlogic Meson G12B S922X SoC items: - enum: + - azw,gsking-x - azw,gtking - azw,gtking-pro - hardkernel,odroid-n2 From 93db2ce05204e240e9ee0933e02b75b433e609d5 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Tue, 19 Jan 2021 14:57:34 +0000 Subject: [PATCH 552/584] arm64: dts: meson: add initial Beelink GS-King-X device-tree The Shenzen AZW (Beelink) GS-King-X is based on the Amlogic W400 reference board with an S922X-H chip. - 4GB LPDDR4 RAM - 64GB eMMC storage - 10/100/1000 Base-T Ethernet - AP6356S Wireless (802.11 a/b/g/n/ac, BT 4.1) - HDMI 2.1 video - S/PDIF optical output - 2x ESS9018 audio DACs - 4x Ricor RT6862 audio amps - Analogue headphone output - 1x USB 2.0 OTG port - 3x USB 3.0 ports - IR receiver - 1x micro SD card slot (internal) - USB SATA controller with 2x 3.5" drive bays - 1x Power on/off button Signed-off-by: Christian Hewitt Acked-by: Martin Blumenstingl Tested-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210119145734.12675-3-christianshewitt@gmail.com --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-g12b-gsking-x.dts | 133 ++++++++++++++++++ 2 files changed, 134 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index ced03946314f..dce41cd3f347 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -3,6 +3,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts new file mode 100644 index 000000000000..211191f66344 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts @@ -0,0 +1,133 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2019 BayLibre, SAS + * Author: Neil Armstrong + * Copyright (c) 2019 Christian Hewitt + */ + +/dts-v1/; + +#include "meson-g12b-w400.dtsi" +#include +#include + +/ { + compatible = "azw,gsking-x", "amlogic,g12b"; + model = "Beelink GS-King X"; + + aliases { + rtc0 = &rtc; + rtc1 = &vrtc; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <100>; + + power-button { + label = "power"; + linux,code = ; + gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_HIGH>; + }; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + model = "GSKING-X"; + audio-aux-devs = <&tdmout_a>; + audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 1", + "TDMOUT_A IN 1", "FRDDR_B OUT 1", + "TDMOUT_A IN 2", "FRDDR_C OUT 1", + "TDM_A Playback", "TDMOUT_A OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + status = "okay"; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_a>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_A>; + }; + }; + + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&arb { + status = "okay"; +}; + +&clkc_audio { + status = "okay"; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + +&tdmif_a { + status = "okay"; +}; + +&tdmout_a { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; From 933b80eda017c64c15b7f0e63961109d85b426b7 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Fri, 1 Jan 2021 06:37:37 +0000 Subject: [PATCH 553/584] arm64: dts: meson: shorten audio card names for alsa compatibility This patch shortens all audio card model names by dropping the SoC prefix (for conformity) and rewording those that are still longer than alsa's 15 character name limit [0] to avoid userspace config issues. [0] https://github.com/torvalds/linux/blob/master/Documentation/sound/alsa-configuration.rst#common-parameters-for-top-sound-card-modules Signed-off-by: Christian Hewitt Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210101063737.26635-1-christianshewitt@gmail.com --- arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi | 2 +- arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi | 2 +- arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi | 2 +- arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts | 2 +- arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts | 2 +- 21 files changed, 21 insertions(+), 21 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts index b00d0468c753..81269ccc2496 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts @@ -181,7 +181,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12A-SEI510"; + model = "SEI510"; audio-aux-devs = <&tdmout_a>, <&tdmout_b>, <&tdmin_a>, <&tdmin_b>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts index 463a72d6bb7c..579f3d02d613 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts @@ -150,7 +150,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12A-X96-MAX"; + model = "X96-MAX"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts index 0e5c500fb78f..0e331aa5a2d7 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts @@ -44,7 +44,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-GTKING-PRO"; + model = "GTKING-PRO"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts index 10b87eb97b14..a7db84a500bb 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking.dts @@ -28,7 +28,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-GTKING"; + model = "GTKING"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index 39a09661c5f6..abc052c72420 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi @@ -211,7 +211,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-ODROID-N2"; + model = "ODROID-N2"; audio-widgets = "Line", "Lineout"; audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>, <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>, diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts index b57bb0befc69..0c7892600d56 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-ugoos-am6.dts @@ -23,7 +23,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-UGOOS-AM6"; + model = "UGOOS-AM6"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi index c2480bab8d33..2d7032f41e4b 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi @@ -186,7 +186,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S9XX-PC"; + model = "LIBRETECH-PC"; audio-aux-devs = <&dio2133>; audio-widgets = "Speaker", "7J4-14 LEFT", "Speaker", "7J4-11 RIGHT"; diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi index 6b57e15aade3..dafc841f7c16 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi @@ -121,7 +121,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GX-P230-Q200"; + model = "P230-Q200"; audio-aux-devs = <&dio2133>; audio-widgets = "Line", "Lineout"; audio-routing = "AU2 INL", "ACODEC LOLP", diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts index 089e0636ba8a..7273eed5292c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nanopi-k2.dts @@ -134,7 +134,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-NANOPI-K2"; + model = "NANOPI-K2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts index b5b11cb9f393..f887bfb445fd 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts @@ -143,7 +143,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-NEXBOX-A95X"; + model = "NEXBOX-A95X"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts index c04ef57f7b3b..bfaf7f41a2d6 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-odroidc2.dts @@ -176,7 +176,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-ODROID-C2"; + model = "ODROID-C2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts index 0c1570153842..58733017eda8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-hub.dts @@ -15,7 +15,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-WETEK-HUB"; + model = "WETEK-HUB"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts index f2562c7de67c..6eae692792ec 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts @@ -50,7 +50,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXBB-WETEK-PLAY2"; + model = "WETEK-PLAY2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts index 9e43f4dca90d..2d769203f671 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts @@ -118,7 +118,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S805X-AC"; + model = "LIBRETECH-AC"; audio-widgets = "Speaker", "9J5-3 LEFT", "Speaker", "9J5-2 RIGHT"; audio-routing = "9J5-3 LEFT", "ACODEC LOLN", diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts index 45adae480a3d..60feac0179c0 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-khadas-vim.dts @@ -66,7 +66,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-KHADAS-VIM1"; + model = "KHADAS-VIM"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts index 9a3c08e6e6cc..93d8f8aff70d 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts @@ -159,7 +159,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S905X-CC-V2"; + model = "LIBRETECH-CC-V2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts index 5ae7bb6209cb..82bfabfbd39c 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc.dts @@ -135,7 +135,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXL-LIBRETECH-S905X-CC"; + model = "LIBRETECH-CC"; audio-aux-devs = <&dio2133>; audio-widgets = "Line", "Lineout"; audio-routing = "AU2 INL", "ACODEC LOLN", diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts index 25857e0c0831..18a4b7a6c5df 100644 --- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts +++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts @@ -148,7 +148,7 @@ sound { compatible = "amlogic,gx-sound-card"; - model = "GXM-KHADAS-VIM2"; + model = "KHADAS-VIM2"; assigned-clocks = <&clkc CLKID_MPLL0>, <&clkc CLKID_MPLL1>, <&clkc CLKID_MPLL2>; diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi index d3b25163b421..877e3b989203 100644 --- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi @@ -170,7 +170,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "G12B-KHADAS-VIM3"; + model = "KHADAS-VIM3"; audio-aux-devs = <&tdmout_a>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", "TDMOUT_A IN 1", "FRDDR_B OUT 0", diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts index a712273c905a..eadd75e6e067 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts @@ -190,7 +190,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "SM1-ODROID-C4"; + model = "ODROID-C4"; audio-aux-devs = <&tdmout_b>; audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", "TDMOUT_B IN 1", "FRDDR_B OUT 1", diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts index 039a8d0d1e9b..2194a778973f 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts @@ -220,7 +220,7 @@ sound { compatible = "amlogic,axg-sound-card"; - model = "SM1-SEI610"; + model = "SEI610"; audio-aux-devs = <&tdmout_a>, <&tdmout_b>, <&tdmin_a>, <&tdmin_b>; audio-routing = "TDMOUT_A IN 0", "FRDDR_A OUT 0", From 5d3f5d46de425ff0cbbc39faea0d7580c8afdb44 Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Sat, 2 Jan 2021 21:59:00 +0100 Subject: [PATCH 554/584] dt-bindings: sram: Add compatible strings for the Meson AO ARC SRAM Amlogic Meson8, Meson8b and Meson8m2 SoCs embed an ARC EM4 core typically used for managing system suspend. A section of the SoCs SRAM is mapped as memory for this ARC core. Add new compatible strings for the SRAM section for the ARC core memory. Signed-off-by: Martin Blumenstingl Acked-by: Rob Herring Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210102205904.2691120-2-martin.blumenstingl@googlemail.com --- Documentation/devicetree/bindings/sram/sram.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/sram/sram.yaml b/Documentation/devicetree/bindings/sram/sram.yaml index 19d116ff9ddc..6d65771e979c 100644 --- a/Documentation/devicetree/bindings/sram/sram.yaml +++ b/Documentation/devicetree/bindings/sram/sram.yaml @@ -72,6 +72,8 @@ patternProperties: - allwinner,sun4i-a10-sram-d - allwinner,sun9i-a80-smp-sram - allwinner,sun50i-a64-sram-c + - amlogic,meson8-ao-arc-sram + - amlogic,meson8b-ao-arc-sram - amlogic,meson8-smp-sram - amlogic,meson8b-smp-sram - amlogic,meson-gxbb-scp-shmem From 68f3a096d0f3552320635347de68a3bd7abd5d36 Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Sat, 2 Jan 2021 21:59:01 +0100 Subject: [PATCH 555/584] dt-bindings: Amlogic: add the documentation for the SECBUS2 registers The Meson8/Meson8b/Meson8m2 SoCs have a register bank called SECBUS2 which contains registers for various IP blocks such as pin-controller bits for the BSD_EN and TEST_N GPIOs as well as some AO ARC core control bits. The registers can be accessed directly when not running in "secure mode". When "secure mode" is enabled then these registers have to be accessed through secure monitor calls. So far these SoCs are always known to boot in "non-secure mode". Add a binding documentation using syscon (as these registers are shared across different IPs) for the SECBUS2 registers. Signed-off-by: Martin Blumenstingl Reviewed-by: Rob Herring Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210102205904.2691120-3-martin.blumenstingl@googlemail.com --- .../arm/amlogic/amlogic,meson-mx-secbus2.yaml | 42 +++++++++++++++++++ 1 file changed, 42 insertions(+) create mode 100644 Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-mx-secbus2.yaml diff --git a/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-mx-secbus2.yaml b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-mx-secbus2.yaml new file mode 100644 index 000000000000..eee7cda9f91b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-mx-secbus2.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/arm/amlogic/amlogic,meson-mx-secbus2.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: Amlogic Meson8/Meson8b/Meson8m2 SECBUS2 register interface + +maintainers: + - Martin Blumenstingl + +description: | + The Meson8/Meson8b/Meson8m2 SoCs have a register bank called SECBUS2 which + contains registers for various IP blocks such as pin-controller bits for + the BSD_EN and TEST_N GPIOs as well as some AO ARC core control bits. + The registers can be accessed directly when not running in "secure mode". + When "secure mode" is enabled then these registers have to be accessed + through secure monitor calls. + +properties: + compatible: + items: + - enum: + - amlogic,meson8-secbus2 + - amlogic,meson8b-secbus2 + - const: syscon + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + secbus2: system-controller@4000 { + compatible = "amlogic,meson8-secbus2", "syscon"; + reg = <0x4000 0x2000>; + }; From fb606cdadbfca902fe7e9619835e1db66141c640 Mon Sep 17 00:00:00 2001 From: Martin Blumenstingl Date: Sat, 2 Jan 2021 21:59:04 +0100 Subject: [PATCH 556/584] ARM: dts: meson: add the AO ARC remote processor The 32-bit Amlogic Meson SoCs embed an ARC processor in the Always-On power domain which is typically used for managing system suspend. The memory for this ARC core is taken from the AHB SRAM area. Depending on the actual SoC a different ARC core is used: - Meson6 and earlier: some ARCv1 ISA based core (probably an ARC625) - Meson8 and later: an ARC EM4 (ARCv2 ISA) based core Add the device-tree node for this remote-processor along with the required SRAM sections, clocks and reset-lines. Also use the SoC-specific compatible string to manage any differences (should they exist). On Meson8, Meson8b and Meson8m2 the "secbus2" IO region is needed as some bits need to be programmed there. Add this IO region for those SoCs as well. Signed-off-by: Martin Blumenstingl Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210102205904.2691120-6-martin.blumenstingl@googlemail.com --- arch/arm/boot/dts/meson.dtsi | 7 +++++++ arch/arm/boot/dts/meson8.dtsi | 21 +++++++++++++++++++++ arch/arm/boot/dts/meson8b.dtsi | 21 +++++++++++++++++++++ 3 files changed, 49 insertions(+) diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi index 7649dd1e0b9e..21ecf3335852 100644 --- a/arch/arm/boot/dts/meson.dtsi +++ b/arch/arm/boot/dts/meson.dtsi @@ -195,6 +195,13 @@ #size-cells = <1>; ranges = <0x0 0xc8100000 0x100000>; + ao_arc_rproc: remoteproc@1c { + compatible= "amlogic,meson-mx-ao-arc"; + reg = <0x1c 0x8>, <0x38 0x8>; + reg-names = "remap", "cpu"; + status = "disabled"; + }; + ir_receiver: ir-receiver@480 { compatible= "amlogic,meson6-ir"; reg = <0x480 0x20>; diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi index 04688e8abce2..93f09b5d1503 100644 --- a/arch/arm/boot/dts/meson8.dtsi +++ b/arch/arm/boot/dts/meson8.dtsi @@ -315,6 +315,14 @@ }; }; +&ao_arc_rproc { + compatible= "amlogic,meson8-ao-arc", "amlogic,meson-mx-ao-arc"; + amlogic,secbus2 = <&secbus2>; + sram = <&ao_arc_sram>; + resets = <&reset RESET_MEDIA_CPU>; + clocks = <&clkc CLKID_AO_MEDIA_CPU>; +}; + &cbus { reset: reset-controller@4404 { compatible = "amlogic,meson8b-reset"; @@ -442,6 +450,12 @@ }; &ahb_sram { + ao_arc_sram: ao-arc-sram@0 { + compatible = "amlogic,meson8-ao-arc-sram"; + reg = <0x0 0x8000>; + pool; + }; + smp-sram@1ff80 { compatible = "amlogic,meson8-smp-sram"; reg = <0x1ff80 0x8>; @@ -577,6 +591,13 @@ clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk"; }; +&secbus { + secbus2: system-controller@4000 { + compatible = "amlogic,meson8-secbus2", "syscon"; + reg = <0x4000 0x2000>; + }; +}; + &sdio { compatible = "amlogic,meson8-sdio", "amlogic,meson-mx-sdio"; clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi index 2401cdf5f751..a285c34aef94 100644 --- a/arch/arm/boot/dts/meson8b.dtsi +++ b/arch/arm/boot/dts/meson8b.dtsi @@ -266,6 +266,14 @@ }; }; +&ao_arc_rproc { + compatible= "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc"; + amlogic,secbus2 = <&secbus2>; + sram = <&ao_arc_sram>; + resets = <&reset RESET_MEDIA_CPU>; + clocks = <&clkc CLKID_AO_MEDIA_CPU>; +}; + &cbus { reset: reset-controller@4404 { compatible = "amlogic,meson8b-reset"; @@ -410,6 +418,12 @@ }; &ahb_sram { + ao_arc_sram: ao-arc-sram@0 { + compatible = "amlogic,meson8b-ao-arc-sram"; + reg = <0x0 0x8000>; + pool; + }; + smp-sram@1ff80 { compatible = "amlogic,meson8b-smp-sram"; reg = <0x1ff80 0x8>; @@ -574,6 +588,13 @@ clock-names = "clkin0", "clkin1", "clkin2", "clkin3", "pclk"; }; +&secbus { + secbus2: system-controller@4000 { + compatible = "amlogic,meson8b-secbus2", "syscon"; + reg = <0x4000 0x2000>; + }; +}; + &sdio { compatible = "amlogic,meson8b-sdio", "amlogic,meson-mx-sdio"; clocks = <&clkc CLKID_SDIO>, <&clkc CLKID_CLK81>; From 6fb82afbe2a5a9d3ac4bde5fd81b7ad568a260ea Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Mon, 11 Jan 2021 13:58:31 +0000 Subject: [PATCH 557/584] arm64: dts: meson: add i2c3/rtc nodes and rtc aliases to ODROID-N2 dtsi Enable the onboard pcf8563 rtc hardware on ODROID N2/N2+ boards via the common dtsi. Also add aliases to ensure vrtc does not claim /dev/rtc0. Signed-off-by: Christian Hewitt Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210111135831.2218-1-christianshewitt@gmail.com --- .../boot/dts/amlogic/meson-g12b-odroid-n2.dtsi | 14 ++++++++++++++ 1 file changed, 14 insertions(+) diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi index abc052c72420..58ce569b2ace 100644 --- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi +++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi @@ -13,6 +13,8 @@ aliases { serial0 = &uart_AO; ethernet0 = ðmac; + rtc0 = &rtc; + rtc1 = &vrtc; }; dioo2133: audio-amplifier-0 { @@ -478,6 +480,18 @@ linux,rc-map-name = "rc-odroid"; }; +&i2c3 { + status = "okay"; + pinctrl-0 = <&i2c3_sda_a_pins>, <&i2c3_sck_a_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + &pwm_ab { pinctrl-0 = <&pwm_a_e_pins>; pinctrl-names = "default"; From 39be8f441f78908e97ff913571e10ec03387a63a Mon Sep 17 00:00:00 2001 From: Artem Lapkin Date: Fri, 29 Jan 2021 16:50:40 +0800 Subject: [PATCH 558/584] arm64: dts: meson: fix broken wifi node for Khadas VIM3L move &sd_emmc_a ... from /* */ commented area, because cant load wifi fw without sd-uhs-sdr50 option on VIM3L [ 11.686590] brcmfmac: brcmf_chip_cores_check: CPU core not detected [ 11.696382] brcmfmac: brcmf_sdio_probe_attach: brcmf_chip_attach failed! [ 11.706240] brcmfmac: brcmf_sdio_probe: brcmf_sdio_probe_attach failed [ 11.715890] brcmfmac: brcmf_ops_sdio_probe: F2 error, probe failed -19... [ 13.718424] brcmfmac: brcmf_chip_recognition: chip backplane type 15 is not supported Signed-off-by: Artem Lapkin Fixes: f1bb924e8f5b ("arm64: dts: meson: fix mmc0 tuning error on Khadas VIM3") Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210129085041.1408540-1-art@khadas.com --- arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts index 4b517ca72059..06de0b1ce726 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-khadas-vim3l.dts @@ -89,13 +89,12 @@ status = "okay"; }; -&sd_emmc_a { - sd-uhs-sdr50; -}; - &usb { phys = <&usb2_phy0>, <&usb2_phy1>; phy-names = "usb2-phy0", "usb2-phy1"; }; */ +&sd_emmc_a { + sd-uhs-sdr50; +}; From ad6d08d9e909be81c135355716590304e99543b7 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Tue, 2 Feb 2021 02:10:17 +0000 Subject: [PATCH 559/584] dt-bindings: arm: amlogic: sort SM1 bindings Sort the bindings before adding new SM1 devices. Signed-off-by: Christian Hewitt Acked-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210202021021.11068-2-christianshewitt@gmail.com --- Documentation/devicetree/bindings/arm/amlogic.yaml | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml index 6bef60ddda64..b21ba8ba23dd 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.yaml +++ b/Documentation/devicetree/bindings/arm/amlogic.yaml @@ -164,9 +164,9 @@ properties: - description: Boards with the Amlogic Meson SM1 S905X3/D3/Y3 SoC items: - enum: - - seirobotics,sei610 - - khadas,vim3l - hardkernel,odroid-c4 + - khadas,vim3l + - seirobotics,sei610 - const: amlogic,sm1 - description: Boards with the Amlogic Meson A1 A113L SoC From fd88408951aef8c3e6e6a1dd2f0acf47b45182a2 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Tue, 2 Feb 2021 02:10:18 +0000 Subject: [PATCH 560/584] arm64: dts: meson: sort Amlogic dtb Makefile Sort the Makefile before adding new SM1 devices. Signed-off-by: Christian Hewitt Acked-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210202021021.11068-3-christianshewitt@gmail.com --- arch/arm64/boot/dts/amlogic/Makefile | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index dce41cd3f347..f3c8a85fe987 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -45,7 +45,7 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-libretech-pc.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb -dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-c4.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb From 88d537bc92ca035e2a9920b0abc750dd62146520 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Wed, 3 Feb 2021 10:29:23 -0800 Subject: [PATCH 561/584] arm64: dts: meson: convert meson-sm1-odroid-c4 to dtsi Convert the ODROID-C4 dts to meson-sm1-odroid.dtsi and C4 board dts in preparation for adding additional C4 family boards. Signed-off-by: Christian Hewitt Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210202021021.11068-4-christianshewitt@gmail.com --- .../boot/dts/amlogic/meson-sm1-odroid-c4.dts | 427 +---------------- .../boot/dts/amlogic/meson-sm1-odroid.dtsi | 442 ++++++++++++++++++ 2 files changed, 443 insertions(+), 426 deletions(-) create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts index eadd75e6e067..b2a4e823c1d8 100644 --- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-c4.dts @@ -5,34 +5,12 @@ /dts-v1/; -#include "meson-sm1.dtsi" -#include -#include -#include +#include "meson-sm1-odroid.dtsi" / { compatible = "hardkernel,odroid-c4", "amlogic,sm1"; model = "Hardkernel ODROID-C4"; - aliases { - serial0 = &uart_AO; - ethernet0 = ðmac; - }; - - chosen { - stdout-path = "serial0:115200n8"; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x0 0x0 0x40000000>; - }; - - emmc_pwrseq: emmc-pwrseq { - compatible = "mmc-pwrseq-emmc"; - reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; - }; - leds { compatible = "gpio-leds"; @@ -45,96 +23,6 @@ }; }; - tflash_vdd: regulator-tflash_vdd { - compatible = "regulator-fixed"; - - regulator-name = "TFLASH_VDD"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - - gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>; - enable-active-high; - regulator-always-on; - }; - - tf_io: gpio-regulator-tf_io { - compatible = "regulator-gpio"; - - regulator-name = "TF_IO"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - - gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; - gpios-states = <0>; - - states = <3300000 0>, - <1800000 1>; - }; - - flash_1v8: regulator-flash_1v8 { - compatible = "regulator-fixed"; - regulator-name = "FLASH_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - main_12v: regulator-main_12v { - compatible = "regulator-fixed"; - regulator-name = "12V"; - regulator-min-microvolt = <12000000>; - regulator-max-microvolt = <12000000>; - regulator-always-on; - }; - - vcc_5v: regulator-vcc_5v { - compatible = "regulator-fixed"; - regulator-name = "5V"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - vin-supply = <&main_12v>; - }; - - vcc_1v8: regulator-vcc_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VCC_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vcc_3v3>; - regulator-always-on; - }; - - vcc_3v3: regulator-vcc_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - /* FIXME: actually controlled by VDDCPU_B_EN */ - }; - - vddcpu: regulator-vddcpu { - /* - * MP8756GD Regulator. - */ - compatible = "pwm-regulator"; - - regulator-name = "VDDCPU"; - regulator-min-microvolt = <721000>; - regulator-max-microvolt = <1022000>; - - vin-supply = <&main_12v>; - - pwms = <&pwm_AO_cd 1 1250 0>; - pwm-dutycycle-range = <100 0>; - - regulator-boot-on; - regulator-always-on; - }; - hub_5v: regulator-hub_5v { compatible = "regulator-fixed"; regulator-name = "HUB_5V"; @@ -147,215 +35,12 @@ enable-active-high; }; - usb_pwr_en: regulator-usb_pwr_en { - compatible = "regulator-fixed"; - regulator-name = "USB_PWR_EN"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - vin-supply = <&vcc_5v>; - - /* Connected to the microUSB port power enable */ - gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; - enable-active-high; - }; - - vddao_1v8: regulator-vddao_1v8 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_1V8"; - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - vin-supply = <&vddao_3v3>; - regulator-always-on; - }; - - vddao_3v3: regulator-vddao_3v3 { - compatible = "regulator-fixed"; - regulator-name = "VDDAO_3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - vin-supply = <&main_12v>; - regulator-always-on; - }; - - hdmi-connector { - compatible = "hdmi-connector"; - type = "a"; - - port { - hdmi_connector_in: endpoint { - remote-endpoint = <&hdmi_tx_tmds_out>; - }; - }; - }; - sound { - compatible = "amlogic,axg-sound-card"; model = "ODROID-C4"; - audio-aux-devs = <&tdmout_b>; - audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", - "TDMOUT_B IN 1", "FRDDR_B OUT 1", - "TDMOUT_B IN 2", "FRDDR_C OUT 1", - "TDM_B Playback", "TDMOUT_B OUT"; - - assigned-clocks = <&clkc CLKID_MPLL2>, - <&clkc CLKID_MPLL0>, - <&clkc CLKID_MPLL1>; - assigned-clock-parents = <0>, <0>, <0>; - assigned-clock-rates = <294912000>, - <270950400>, - <393216000>; - status = "okay"; - - dai-link-0 { - sound-dai = <&frddr_a>; - }; - - dai-link-1 { - sound-dai = <&frddr_b>; - }; - - dai-link-2 { - sound-dai = <&frddr_c>; - }; - - /* 8ch hdmi interface */ - dai-link-3 { - sound-dai = <&tdmif_b>; - dai-format = "i2s"; - dai-tdm-slot-tx-mask-0 = <1 1>; - dai-tdm-slot-tx-mask-1 = <1 1>; - dai-tdm-slot-tx-mask-2 = <1 1>; - dai-tdm-slot-tx-mask-3 = <1 1>; - mclk-fs = <256>; - - codec { - sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; - }; - }; - - /* hdmi glue */ - dai-link-4 { - sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; - - codec { - sound-dai = <&hdmi_tx>; - }; - }; }; }; -&arb { - status = "okay"; -}; - -&clkc_audio { - status = "okay"; -}; - -&cpu0 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU_CLK>; - clock-latency = <50000>; -}; - -&cpu1 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU1_CLK>; - clock-latency = <50000>; -}; - -&cpu2 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU2_CLK>; - clock-latency = <50000>; -}; - -&cpu3 { - cpu-supply = <&vddcpu>; - operating-points-v2 = <&cpu_opp_table>; - clocks = <&clkc CLKID_CPU3_CLK>; - clock-latency = <50000>; -}; - -&ext_mdio { - external_phy: ethernet-phy@0 { - /* Realtek RTL8211F (0x001cc916) */ - reg = <0>; - max-speed = <1000>; - - interrupt-parent = <&gpio_intc>; - /* MAC_INTR on GPIOZ_14 */ - interrupts = <26 IRQ_TYPE_LEVEL_LOW>; - }; -}; - -ðmac { - pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; - pinctrl-names = "default"; - status = "okay"; - phy-mode = "rgmii"; - phy-handle = <&external_phy>; - amlogic,tx-delay-ns = <2>; -}; - -&frddr_a { - status = "okay"; -}; - -&frddr_b { - status = "okay"; -}; - -&frddr_c { - status = "okay"; -}; - &gpio { - gpio-line-names = - /* GPIOZ */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - /* GPIOH */ - "", "", "", "", "", - "PIN_36", /* GPIOH_5 */ - "PIN_26", /* GPIOH_6 */ - "PIN_32", /* GPIOH_7 */ - "", - /* BOOT */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", "", "", - /* GPIOC */ - "", "", "", "", "", "", "", "", - /* GPIOA */ - "", "", "", "", "", "", "", "", - "", "", "", "", "", "", - "PIN_27", /* GPIOA_14 */ - "PIN_28", /* GPIOA_15 */ - /* GPIOX */ - "PIN_16", /* GPIOX_0 */ - "PIN_18", /* GPIOX_1 */ - "PIN_22", /* GPIOX_2 */ - "PIN_11", /* GPIOX_3 */ - "PIN_13", /* GPIOX_4 */ - "PIN_7", /* GPIOX_5 */ - "PIN_33", /* GPIOX_6 */ - "PIN_15", /* GPIOX_7 */ - "PIN_19", /* GPIOX_8 */ - "PIN_21", /* GPIOX_9 */ - "PIN_24", /* GPIOX_10 */ - "PIN_23", /* GPIOX_11 */ - "PIN_8", /* GPIOX_12 */ - "PIN_10", /* GPIOX_13 */ - "PIN_29", /* GPIOX_14 */ - "PIN_31", /* GPIOX_15 */ - "PIN_12", /* GPIOX_16 */ - "PIN_3", /* GPIOX_17 */ - "PIN_5", /* GPIOX_18 */ - "PIN_35"; /* GPIOX_19 */ - /* * WARNING: The USB Hub on the Odroid-C4 needs a reset signal * to be turned high in order to be detected by the USB Controller @@ -370,120 +55,10 @@ }; }; -&gpio_ao { - gpio-line-names = - /* GPIOAO */ - "", "", "", "", - "PIN_47", /* GPIOAO_4 */ - "", "", - "PIN_45", /* GPIOAO_7 */ - "PIN_46", /* GPIOAO_8 */ - "PIN_44", /* GPIOAO_9 */ - "PIN_42", /* GPIOAO_10 */ - "", - /* GPIOE */ - "", "", ""; -}; - -&hdmi_tx { - status = "okay"; - pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; - pinctrl-names = "default"; - hdmi-supply = <&vcc_5v>; -}; - -&hdmi_tx_tmds_port { - hdmi_tx_tmds_out: endpoint { - remote-endpoint = <&hdmi_connector_in>; - }; -}; - &ir { - status = "okay"; - pinctrl-0 = <&remote_input_ao_pins>; - pinctrl-names = "default"; linux,rc-map-name = "rc-odroid"; }; -&pwm_AO_cd { - pinctrl-0 = <&pwm_ao_d_e_pins>; - pinctrl-names = "default"; - clocks = <&xtal>; - clock-names = "clkin1"; - status = "okay"; -}; - -&saradc { - status = "okay"; -}; - -/* SD card */ -&sd_emmc_b { - status = "okay"; - pinctrl-0 = <&sdcard_c_pins>; - pinctrl-1 = <&sdcard_clk_gate_c_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <4>; - cap-sd-highspeed; - max-frequency = <200000000>; - sd-uhs-sdr12; - sd-uhs-sdr25; - sd-uhs-sdr50; - sd-uhs-sdr104; - disable-wp; - - cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; - vmmc-supply = <&tflash_vdd>; - vqmmc-supply = <&tf_io>; -}; - -/* eMMC */ -&sd_emmc_c { - status = "okay"; - pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; - pinctrl-1 = <&emmc_clk_gate_pins>; - pinctrl-names = "default", "clk-gate"; - - bus-width = <8>; - cap-mmc-highspeed; - mmc-ddr-1_8v; - mmc-hs200-1_8v; - max-frequency = <200000000>; - disable-wp; - - mmc-pwrseq = <&emmc_pwrseq>; - vmmc-supply = <&vcc_3v3>; - vqmmc-supply = <&flash_1v8>; -}; - -&tdmif_b { - status = "okay"; -}; - -&tdmout_b { - status = "okay"; -}; - -&tohdmitx { - status = "okay"; -}; - -&uart_AO { - status = "okay"; - pinctrl-0 = <&uart_ao_a_pins>; - pinctrl-names = "default"; -}; - -&usb { - status = "okay"; - vbus-supply = <&usb_pwr_en>; -}; - -&usb2_phy0 { - phy-supply = <&vcc_5v>; -}; - &usb2_phy1 { /* Enable the hub which is connected to this port */ phy-supply = <&hub_5v>; diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi new file mode 100644 index 000000000000..d14716b3d0f1 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi @@ -0,0 +1,442 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Dongjin Kim + */ + +#include "meson-sm1.dtsi" +#include +#include +#include + +/ { + aliases { + serial0 = &uart_AO; + ethernet0 = ðmac; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x40000000>; + }; + + emmc_pwrseq: emmc-pwrseq { + compatible = "mmc-pwrseq-emmc"; + reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>; + }; + + tflash_vdd: regulator-tflash_vdd { + compatible = "regulator-fixed"; + + regulator-name = "TFLASH_VDD"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio_ao GPIOAO_3 GPIO_OPEN_DRAIN>; + enable-active-high; + regulator-always-on; + }; + + tf_io: gpio-regulator-tf_io { + compatible = "regulator-gpio"; + + regulator-name = "TF_IO"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio_ao GPIOAO_6 GPIO_ACTIVE_HIGH>; + gpios-states = <0>; + + states = <3300000 0>, + <1800000 1>; + }; + + flash_1v8: regulator-flash_1v8 { + compatible = "regulator-fixed"; + regulator-name = "FLASH_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + main_12v: regulator-main_12v { + compatible = "regulator-fixed"; + regulator-name = "12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-always-on; + }; + + vcc_5v: regulator-vcc_5v { + compatible = "regulator-fixed"; + regulator-name = "5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + vin-supply = <&main_12v>; + }; + + vcc_1v8: regulator-vcc_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VCC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vcc_3v3>; + regulator-always-on; + }; + + vcc_3v3: regulator-vcc_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + /* FIXME: actually controlled by VDDCPU_B_EN */ + }; + + vddcpu: regulator-vddcpu { + /* + * MP8756GD Regulator. + */ + compatible = "pwm-regulator"; + + regulator-name = "VDDCPU"; + regulator-min-microvolt = <721000>; + regulator-max-microvolt = <1022000>; + + vin-supply = <&main_12v>; + + pwms = <&pwm_AO_cd 1 1250 0>; + pwm-dutycycle-range = <100 0>; + + regulator-boot-on; + regulator-always-on; + }; + + usb_pwr_en: regulator-usb_pwr_en { + compatible = "regulator-fixed"; + regulator-name = "USB_PWR_EN"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + vin-supply = <&vcc_5v>; + + /* Connected to the microUSB port power enable */ + gpio = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vddao_1v8: regulator-vddao_1v8 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + vin-supply = <&vddao_3v3>; + regulator-always-on; + }; + + vddao_3v3: regulator-vddao_3v3 { + compatible = "regulator-fixed"; + regulator-name = "VDDAO_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + vin-supply = <&main_12v>; + regulator-always-on; + }; + + hdmi-connector { + compatible = "hdmi-connector"; + type = "a"; + + port { + hdmi_connector_in: endpoint { + remote-endpoint = <&hdmi_tx_tmds_out>; + }; + }; + }; + + sound { + compatible = "amlogic,axg-sound-card"; + audio-aux-devs = <&tdmout_b>; + audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1", + "TDMOUT_B IN 1", "FRDDR_B OUT 1", + "TDMOUT_B IN 2", "FRDDR_C OUT 1", + "TDM_B Playback", "TDMOUT_B OUT"; + + assigned-clocks = <&clkc CLKID_MPLL2>, + <&clkc CLKID_MPLL0>, + <&clkc CLKID_MPLL1>; + assigned-clock-parents = <0>, <0>, <0>; + assigned-clock-rates = <294912000>, + <270950400>, + <393216000>; + status = "okay"; + + dai-link-0 { + sound-dai = <&frddr_a>; + }; + + dai-link-1 { + sound-dai = <&frddr_b>; + }; + + dai-link-2 { + sound-dai = <&frddr_c>; + }; + + /* 8ch hdmi interface */ + dai-link-3 { + sound-dai = <&tdmif_b>; + dai-format = "i2s"; + dai-tdm-slot-tx-mask-0 = <1 1>; + dai-tdm-slot-tx-mask-1 = <1 1>; + dai-tdm-slot-tx-mask-2 = <1 1>; + dai-tdm-slot-tx-mask-3 = <1 1>; + mclk-fs = <256>; + + codec { + sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>; + }; + }; + + /* hdmi glue */ + dai-link-4 { + sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>; + + codec { + sound-dai = <&hdmi_tx>; + }; + }; + }; +}; + +&arb { + status = "okay"; +}; + +&clkc_audio { + status = "okay"; +}; + +&cpu0 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU_CLK>; + clock-latency = <50000>; +}; + +&cpu1 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU1_CLK>; + clock-latency = <50000>; +}; + +&cpu2 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU2_CLK>; + clock-latency = <50000>; +}; + +&cpu3 { + cpu-supply = <&vddcpu>; + operating-points-v2 = <&cpu_opp_table>; + clocks = <&clkc CLKID_CPU3_CLK>; + clock-latency = <50000>; +}; + +&ext_mdio { + external_phy: ethernet-phy@0 { + /* Realtek RTL8211F (0x001cc916) */ + reg = <0>; + max-speed = <1000>; + + interrupt-parent = <&gpio_intc>; + /* MAC_INTR on GPIOZ_14 */ + interrupts = <26 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +ðmac { + pinctrl-0 = <ð_pins>, <ð_rgmii_pins>; + pinctrl-names = "default"; + status = "okay"; + phy-mode = "rgmii"; + phy-handle = <&external_phy>; + amlogic,tx-delay-ns = <2>; +}; + +&frddr_a { + status = "okay"; +}; + +&frddr_b { + status = "okay"; +}; + +&frddr_c { + status = "okay"; +}; + +&gpio { + gpio-line-names = + /* GPIOZ */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOH */ + "", "", "", "", "", + "PIN_36", /* GPIOH_5 */ + "PIN_26", /* GPIOH_6 */ + "PIN_32", /* GPIOH_7 */ + "", + /* BOOT */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + /* GPIOC */ + "", "", "", "", "", "", "", "", + /* GPIOA */ + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", + "PIN_27", /* GPIOA_14 */ + "PIN_28", /* GPIOA_15 */ + /* GPIOX */ + "PIN_16", /* GPIOX_0 */ + "PIN_18", /* GPIOX_1 */ + "PIN_22", /* GPIOX_2 */ + "PIN_11", /* GPIOX_3 */ + "PIN_13", /* GPIOX_4 */ + "PIN_7", /* GPIOX_5 */ + "PIN_33", /* GPIOX_6 */ + "PIN_15", /* GPIOX_7 */ + "PIN_19", /* GPIOX_8 */ + "PIN_21", /* GPIOX_9 */ + "PIN_24", /* GPIOX_10 */ + "PIN_23", /* GPIOX_11 */ + "PIN_8", /* GPIOX_12 */ + "PIN_10", /* GPIOX_13 */ + "PIN_29", /* GPIOX_14 */ + "PIN_31", /* GPIOX_15 */ + "PIN_12", /* GPIOX_16 */ + "PIN_3", /* GPIOX_17 */ + "PIN_5", /* GPIOX_18 */ + "PIN_35"; /* GPIOX_19 */ +}; + +&gpio_ao { + gpio-line-names = + /* GPIOAO */ + "", "", "", "", + "PIN_47", /* GPIOAO_4 */ + "", "", + "PIN_45", /* GPIOAO_7 */ + "PIN_46", /* GPIOAO_8 */ + "PIN_44", /* GPIOAO_9 */ + "PIN_42", /* GPIOAO_10 */ + "", + /* GPIOE */ + "", "", ""; +}; + +&hdmi_tx { + status = "okay"; + pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>; + pinctrl-names = "default"; + hdmi-supply = <&vcc_5v>; +}; + +&hdmi_tx_tmds_port { + hdmi_tx_tmds_out: endpoint { + remote-endpoint = <&hdmi_connector_in>; + }; +}; + +&ir { + status = "okay"; + pinctrl-0 = <&remote_input_ao_pins>; + pinctrl-names = "default"; +}; + +&pwm_AO_cd { + pinctrl-0 = <&pwm_ao_d_e_pins>; + pinctrl-names = "default"; + clocks = <&xtal>; + clock-names = "clkin1"; + status = "okay"; +}; + +&saradc { + status = "okay"; +}; + +/* SD card */ +&sd_emmc_b { + status = "okay"; + pinctrl-0 = <&sdcard_c_pins>; + pinctrl-1 = <&sdcard_clk_gate_c_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <4>; + cap-sd-highspeed; + max-frequency = <200000000>; + sd-uhs-sdr12; + sd-uhs-sdr25; + sd-uhs-sdr50; + sd-uhs-sdr104; + disable-wp; + + cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>; + vmmc-supply = <&tflash_vdd>; + vqmmc-supply = <&tf_io>; +}; + +/* eMMC */ +&sd_emmc_c { + status = "okay"; + pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>; + pinctrl-1 = <&emmc_clk_gate_pins>; + pinctrl-names = "default", "clk-gate"; + + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + mmc-hs200-1_8v; + max-frequency = <200000000>; + disable-wp; + + mmc-pwrseq = <&emmc_pwrseq>; + vmmc-supply = <&vcc_3v3>; + vqmmc-supply = <&flash_1v8>; +}; + +&tdmif_b { + status = "okay"; +}; + +&tdmout_b { + status = "okay"; +}; + +&tohdmitx { + status = "okay"; +}; + +&uart_AO { + status = "okay"; + pinctrl-0 = <&uart_ao_a_pins>; + pinctrl-names = "default"; +}; + +&usb { + status = "okay"; + vbus-supply = <&usb_pwr_en>; +}; + +&usb2_phy0 { + phy-supply = <&vcc_5v>; +}; + From 56f45a21fc445d98219eb8863ce4e80cb97b50bc Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Tue, 2 Feb 2021 02:10:20 +0000 Subject: [PATCH 562/584] dt-bindings: arm: amlogic: add ODROID-HC4 bindings Add the board bindings for the ODROID-HC4 device. Signed-off-by: Christian Hewitt Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210202021021.11068-5-christianshewitt@gmail.com --- Documentation/devicetree/bindings/arm/amlogic.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/amlogic.yaml b/Documentation/devicetree/bindings/arm/amlogic.yaml index b21ba8ba23dd..5f6769bf45bd 100644 --- a/Documentation/devicetree/bindings/arm/amlogic.yaml +++ b/Documentation/devicetree/bindings/arm/amlogic.yaml @@ -165,6 +165,7 @@ properties: items: - enum: - hardkernel,odroid-c4 + - hardkernel,odroid-hc4 - khadas,vim3l - seirobotics,sei610 - const: amlogic,sm1 From 33b14f663df84196cdfbbfccd85d36d10b2d1820 Mon Sep 17 00:00:00 2001 From: Christian Hewitt Date: Tue, 2 Feb 2021 02:10:21 +0000 Subject: [PATCH 563/584] arm64: dts: meson: add initial device-tree for ODROID-HC4 ODROID-HC4 is a derivative of the C4 with minor differences: - 16MB XT25F128B SPI-NOR flash - 2x SATA ports via ASM1061 PCIe to SATA controller - 7-pin header with SPI and I2C for 1-inch OLED display and RTC - 1x USB 2.0 host port Signed-off-by: Christian Hewitt Reviewed-by: Neil Armstrong Signed-off-by: Kevin Hilman Link: https://lore.kernel.org/r/20210202021021.11068-6-christianshewitt@gmail.com --- arch/arm64/boot/dts/amlogic/Makefile | 1 + .../boot/dts/amlogic/meson-sm1-odroid-hc4.dts | 96 +++++++++++++++++++ 2 files changed, 97 insertions(+) create mode 100644 arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile index f3c8a85fe987..78a569d7fa20 100644 --- a/arch/arm64/boot/dts/amlogic/Makefile +++ b/arch/arm64/boot/dts/amlogic/Makefile @@ -47,5 +47,6 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-c4.dtb +dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-hc4.dtb dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts new file mode 100644 index 000000000000..bf15700c4b15 --- /dev/null +++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts @@ -0,0 +1,96 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (c) 2020 Dongjin Kim + */ + +/dts-v1/; + +#include "meson-sm1-odroid.dtsi" + +/ { + compatible = "hardkernel,odroid-hc4", "amlogic,sm1"; + model = "Hardkernel ODROID-HC4"; + + aliases { + rtc0 = &rtc; + rtc1 = &vrtc; + }; + + fan0: pwm-fan { + compatible = "pwm-fan"; + #cooling-cells = <2>; + cooling-min-state = <0>; + cooling-max-state = <3>; + cooling-levels = <0 120 170 220>; + pwms = <&pwm_cd 1 40000 0>; + }; + + leds { + compatible = "gpio-leds"; + + led-blue { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + panic-indicator; + }; + + led-red { + color = ; + function = LED_FUNCTION_POWER; + gpios = <&gpio_ao GPIOAO_7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + sound { + model = "ODROID-HC4"; + }; +}; + +&cpu_thermal { + cooling-maps { + map { + trip = <&cpu_passive>; + cooling-device = <&fan0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; +}; + +&ir { + linux,rc-map-name = "rc-odroid"; +}; + +&i2c2 { + status = "okay"; + pinctrl-0 = <&i2c2_sda_x_pins>, <&i2c2_sck_x_pins>; + pinctrl-names = "default"; + + rtc: rtc@51 { + status = "okay"; + compatible = "nxp,pcf8563"; + reg = <0x51>; + wakeup-source; + }; +}; + +&pcie { + status = "okay"; + reset-gpios = <&gpio GPIOH_4 GPIO_ACTIVE_LOW>; +}; + +&pwm_cd { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm_d_x6_pins>; +}; + +&sd_emmc_c { + status = "disabled"; +}; + +&usb { + phys = <&usb2_phy0>, <&usb2_phy1>; + phy-names = "usb2-phy0", "usb2-phy1"; +}; From 36652a295266095a5f44bdb1c9f2c6400a9c71cf Mon Sep 17 00:00:00 2001 From: Quan Nguyen Date: Tue, 8 Dec 2020 11:37:00 +0700 Subject: [PATCH 564/584] ARM: dts: aspeed: Add device tree for Ampere's Mt. Jade BMC The Mt. Jade BMC is an ASPEED AST2500-based BMC for the Mt. Jade hardware reference platform with Ampere's Altra Processor Family. Signed-off-by: Quan Nguyen Signed-off-by: Phong Vo Signed-off-by: Thang Q. Nguyen Reviewed-by: Andrew Jeffery Reviewed-by: Joel Stanley Link: https://lore.kernel.org/r/20201208043700.23098-3-quan@os.amperecomputing.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/Makefile | 1 + .../arm/boot/dts/aspeed-bmc-ampere-mtjade.dts | 558 ++++++++++++++++++ 2 files changed, 559 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..5271820a5380 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1403,6 +1403,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-ast2500-evb.dtb \ aspeed-ast2600-evb.dtb \ aspeed-bmc-amd-ethanolx.dtb \ + aspeed-bmc-ampere-mtjade.dtb \ aspeed-bmc-arm-centriq2400-rep.dtb \ aspeed-bmc-arm-stardragon4800-rep2.dtb \ aspeed-bmc-bytedance-g220a.dtb \ diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts new file mode 100644 index 000000000000..8f5ec22e51c2 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts @@ -0,0 +1,558 @@ +// SPDX-License-Identifier: GPL-2.0+ +/dts-v1/; +#include "aspeed-g5.dtsi" +#include + +/ { + model = "Ampere Mt. Jade BMC"; + compatible = "ampere,mtjade-bmc", "aspeed,ast2500"; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200 earlyprintk"; + }; + + memory@80000000 { + reg = <0x80000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + vga_memory: framebuffer@9f000000 { + no-map; + reg = <0x9f000000 0x01000000>; /* 16M */ + }; + + gfx_memory: framebuffer { + size = <0x01000000>; + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; + }; + + video_engine_memory: jpegbuffer { + size = <0x02000000>; /* 32M */ + alignment = <0x01000000>; + compatible = "shared-dma-pool"; + reusable; + }; + }; + + leds { + compatible = "gpio-leds"; + + fault { + gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>; + }; + + identify { + gpios = <&gpio ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + shutdown_ack { + label = "SHUTDOWN_ACK"; + gpios = <&gpio ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reboot_ack { + label = "REBOOT_ACK"; + gpios = <&gpio ASPEED_GPIO(J, 3) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + S0_overtemp { + label = "S0_OVERTEMP"; + gpios = <&gpio ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + S0_hightemp { + label = "S0_HIGHTEMP"; + gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + S0_cpu_fault { + label = "S0_CPU_FAULT"; + gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + + S1_overtemp { + label = "S1_OVERTEMP"; + gpios = <&gpio ASPEED_GPIO(Z, 6) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + S1_hightemp { + label = "S1_HIGHTEMP"; + gpios = <&gpio ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + S1_cpu_fault { + label = "S1_CPU_FAULT"; + gpios = <&gpio ASPEED_GPIO(Z, 1) GPIO_ACTIVE_HIGH>; + linux,code = ; + }; + + id_button { + label = "ID_BUTTON"; + gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + }; + + gpioA0mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + mux-gpios = <&gpio ASPEED_GPIO(A, 0) GPIO_ACTIVE_LOW>; + }; + + adc0mux: adc0mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc1mux: adc1mux { + compatible = "io-channel-mux"; + io-channels = <&adc 1>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc2mux: adc2mux { + compatible = "io-channel-mux"; + io-channels = <&adc 2>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc3mux: adc3mux { + compatible = "io-channel-mux"; + io-channels = <&adc 3>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc4mux: adc4mux { + compatible = "io-channel-mux"; + io-channels = <&adc 4>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc5mux: adc5mux { + compatible = "io-channel-mux"; + io-channels = <&adc 5>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc6mux: adc6mux { + compatible = "io-channel-mux"; + io-channels = <&adc 6>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc7mux: adc7mux { + compatible = "io-channel-mux"; + io-channels = <&adc 7>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc8mux: adc8mux { + compatible = "io-channel-mux"; + io-channels = <&adc 8>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc9mux: adc9mux { + compatible = "io-channel-mux"; + io-channels = <&adc 9>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc10mux: adc10mux { + compatible = "io-channel-mux"; + io-channels = <&adc 10>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc11mux: adc11mux { + compatible = "io-channel-mux"; + io-channels = <&adc 11>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc12mux: adc12mux { + compatible = "io-channel-mux"; + io-channels = <&adc 12>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + adc13mux: adc13mux { + compatible = "io-channel-mux"; + io-channels = <&adc 13>; + #io-channel-cells = <1>; + io-channel-names = "parent"; + mux-controls = <&gpioA0mux>; + channels = "s0", "s1"; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc0mux 0>, <&adc0mux 1>, + <&adc1mux 0>, <&adc1mux 1>, + <&adc2mux 0>, <&adc2mux 1>, + <&adc3mux 0>, <&adc3mux 1>, + <&adc4mux 0>, <&adc4mux 1>, + <&adc5mux 0>, <&adc5mux 1>, + <&adc6mux 0>, <&adc6mux 1>, + <&adc7mux 0>, <&adc7mux 1>, + <&adc8mux 0>, <&adc8mux 1>, + <&adc9mux 0>, <&adc9mux 1>, + <&adc10mux 0>, <&adc10mux 1>, + <&adc11mux 0>, <&adc11mux 1>, + <&adc12mux 0>, <&adc12mux 1>, + <&adc13mux 0>, <&adc13mux 1>; + }; + + iio-hwmon-adc14 { + compatible = "iio-hwmon"; + io-channels = <&adc 14>; + }; + + iio-hwmon-battery { + compatible = "iio-hwmon"; + io-channels = <&adc 15>; + }; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; + /* spi-max-frequency = <50000000>; */ +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + m25p,fast-read; + label = "pnor"; + /* spi-max-frequency = <100000000>; */ + }; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd1_default + &pinctrl_rxd1_default + &pinctrl_ncts1_default + &pinctrl_nrts1_default>; +}; + +&uart2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd2_default + &pinctrl_rxd2_default>; +}; + +&uart3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd3_default + &pinctrl_rxd3_default>; +}; + +&uart4 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_txd4_default + &pinctrl_rxd4_default>; +}; + +/* The BMC's uart */ +&uart5 { + status = "okay"; +}; + +&mac1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>; +}; + +&i2c0 { + status = "okay"; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; + eeprom@50 { + compatible = "microchip,24c64", "atmel,24c64"; + reg = <0x50>; + pagesize = <32>; + }; + + inlet_mem2: tmp175@28 { + compatible = "ti,tmp175"; + reg = <0x28>; + }; + + inlet_cpu: tmp175@29 { + compatible = "ti,tmp175"; + reg = <0x29>; + }; + + inlet_mem1: tmp175@2a { + compatible = "ti,tmp175"; + reg = <0x2a>; + }; + + outlet_cpu: tmp175@2b { + compatible = "ti,tmp175"; + reg = <0x2b>; + }; + + outlet1: tmp175@2c { + compatible = "ti,tmp175"; + reg = <0x2c>; + }; + + outlet2: tmp175@2d { + compatible = "ti,tmp175"; + reg = <0x2d>; + }; +}; + +&i2c4 { + status = "okay"; + rtc@51 { + compatible = "nxp,pcf85063a"; + reg = <0x51>; + }; +}; + +&i2c5 { + status = "okay"; +}; + +&i2c6 { + status = "okay"; + psu@58 { + compatible = "pmbus"; + reg = <0x58>; + }; + + psu@59 { + compatible = "pmbus"; + reg = <0x59>; + }; +}; + +&i2c7 { + status = "okay"; +}; + +&i2c8 { + status = "okay"; +}; + +&i2c9 { + status = "okay"; +}; + +&gfx { + status = "okay"; + memory-region = <&gfx_memory>; +}; + +&pinctrl { + aspeed,external-nodes = <&gfx &lhc>; +}; + +&pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2_default &pinctrl_pwm3_default + &pinctrl_pwm4_default &pinctrl_pwm5_default + &pinctrl_pwm6_default &pinctrl_pwm7_default>; + + fan@0 { + reg = <0x02>; + aspeed,fan-tach-ch = /bits/ 8 <0x04>; + }; + + fan@1 { + reg = <0x02>; + aspeed,fan-tach-ch = /bits/ 8 <0x05>; + }; + + fan@2 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x06>; + }; + + fan@3 { + reg = <0x03>; + aspeed,fan-tach-ch = /bits/ 8 <0x07>; + }; + + fan@4 { + reg = <0x04>; + aspeed,fan-tach-ch = /bits/ 8 <0x08>; + }; + + fan@5 { + reg = <0x04>; + aspeed,fan-tach-ch = /bits/ 8 <0x09>; + }; + + fan@6 { + reg = <0x05>; + aspeed,fan-tach-ch = /bits/ 8 <0x0a>; + }; + + fan@7 { + reg = <0x05>; + aspeed,fan-tach-ch = /bits/ 8 <0x0b>; + }; + + fan@8 { + reg = <0x06>; + aspeed,fan-tach-ch = /bits/ 8 <0x0c>; + }; + + fan@9 { + reg = <0x06>; + aspeed,fan-tach-ch = /bits/ 8 <0x0d>; + }; + + fan@10 { + reg = <0x07>; + aspeed,fan-tach-ch = /bits/ 8 <0x0e>; + }; + + fan@11 { + reg = <0x07>; + aspeed,fan-tach-ch = /bits/ 8 <0x0f>; + }; + +}; + +&vhub { + status = "okay"; +}; + +&adc { + status = "okay"; +}; + +&video { + status = "okay"; + memory-region = <&video_engine_memory>; +}; + +&gpio { + gpio-line-names = + /*A0-A7*/ "","","","S0_BMC_SPECIAL_BOOT","","","","", + /*B0-B7*/ "BMC_SELECT_EEPROM","","","", + "POWER_BUTTON","","","", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "","","","","","","","", + /*E0-E7*/ "","","","","","","","", + /*F0-F7*/ "","","BMC_SYS_PSON_L","S0_DDR_SAVE","PGOOD", + "S1_DDR_SAVE","","", + /*G0-G7*/ "S0_FW_BOOT_OK","SHD_REQ_L","","S0_OVERTEMP_L","","", + "","", + /*H0-H7*/ "","","","","","","","", + /*I0-I7*/ "","","S1_BMC_SPECIAL_BOOT","","","","","", + /*J0-J7*/ "S0_HIGHTEMP_L","S0_FAULT_L","S0_SCP_AUTH_FAIL_L","", + "","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","BMC_SYSRESET_L","SPI_AUTH_FAIL_L","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "","","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","UID_BUTTON","","", + /*R0-R7*/ "","","BMC_EXT_HIGHTEMP_L","","","RESET_BUTTON","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","","","","","","","", + /*W0-W7*/ "","","","","","","","", + /*X0-X7*/ "","","","","","","","", + /*Y0-Y7*/ "","","","","","","","", + /*Z0-Z7*/ "S0_BMC_PLIMIT","S1_FAULT_L","S1_FW_BOOT_OK","","", + "S1_SCP_AUTH_FAIL_L","S1_OVERTEMP_L","", + /*AA0-AA7*/ "","","","","","","","", + /*AB0-AB7*/ "S1_HIGHTEMP_L","S1_BMC_PLIMIT","S0_BMC_DDR_ADDR", + "S1_BMC_DDR_ADR","","","","", + /*AC0-AC7*/ "SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L", + "BMC_OCP_PG"; +}; From d050d049f8b8077025292c1ecf456c4ee7f96861 Mon Sep 17 00:00:00 2001 From: John Wang Date: Wed, 2 Dec 2020 13:16:34 +0800 Subject: [PATCH 565/584] ARM: dts: aspeed: Add LCLK to lpc-snoop Signed-off-by: John Wang Reviewed-by: Joel Stanley Link: https://lore.kernel.org/r/20201202051634.490-2-wangzhiqiang.bj@bytedance.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-g4.dtsi | 1 + arch/arm/boot/dts/aspeed-g5.dtsi | 1 + arch/arm/boot/dts/aspeed-g6.dtsi | 1 + 3 files changed, 3 insertions(+) diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed-g4.dtsi index b3dafbc8caca..e7a45ba18fc9 100644 --- a/arch/arm/boot/dts/aspeed-g4.dtsi +++ b/arch/arm/boot/dts/aspeed-g4.dtsi @@ -375,6 +375,7 @@ compatible = "aspeed,ast2400-lpc-snoop"; reg = <0x10 0x8>; interrupts = <8>; + clocks = <&syscon ASPEED_CLK_GATE_LCLK>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi index 5bc0de0f3365..21930521a986 100644 --- a/arch/arm/boot/dts/aspeed-g5.dtsi +++ b/arch/arm/boot/dts/aspeed-g5.dtsi @@ -497,6 +497,7 @@ compatible = "aspeed,ast2500-lpc-snoop"; reg = <0x10 0x8>; interrupts = <8>; + clocks = <&syscon ASPEED_CLK_GATE_LCLK>; status = "disabled"; }; diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi index 810b0676ab03..3ee470c2b7b5 100644 --- a/arch/arm/boot/dts/aspeed-g6.dtsi +++ b/arch/arm/boot/dts/aspeed-g6.dtsi @@ -524,6 +524,7 @@ compatible = "aspeed,ast2600-lpc-snoop"; reg = <0x0 0x80>; interrupts = ; + clocks = <&syscon ASPEED_CLK_GATE_LCLK>; status = "disabled"; }; From d2dc55b96f876616838b61b2378656effd0e14ba Mon Sep 17 00:00:00 2001 From: Andrew Jeffery Date: Tue, 8 Dec 2020 11:56:15 +1030 Subject: [PATCH 566/584] ARM: dts: aspeed: rainier: Add eMMC clock phase compensation Determined by scope measurements at speed. Signed-off-by: Andrew Jeffery Reviewed-by: Joel Stanley Link: https://lore.kernel.org/r/20201208012615.2717412-7-andrew@aj.id.au Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts index a4b77aec5424..72de21f7c941 100644 --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts @@ -195,6 +195,7 @@ &emmc { status = "okay"; + clk-phase-mmc-hs200 = <180>, <180>; }; &fsim0 { From cc36a99de0fa3e4253a00958fddc64c64a557373 Mon Sep 17 00:00:00 2001 From: Lotus Xu Date: Fri, 11 Dec 2020 12:00:01 +0800 Subject: [PATCH 567/584] ARM: dts: aspeed: g220a: Enable ipmb Enable ipmb on i2c4. Signed-off-by: Lotus Xu Signed-off-by: John Wang Reviewed-by: Joel Stanley Link: https://lore.kernel.org/r/20201211040002.1030-1-wangzhiqiang.bj@bytedance.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts index 2feb25b0e43b..1f415e62fbde 100644 --- a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts +++ b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts @@ -446,7 +446,11 @@ &i2c4 { status = "okay"; - + ipmb0@10 { + compatible = "ipmb-dev"; + reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>; + i2c-protocol; + }; }; &i2c5 { From 2b433f7128e7053dd72edbcbf38ff404cc1817e0 Mon Sep 17 00:00:00 2001 From: John Wang Date: Fri, 11 Dec 2020 12:00:02 +0800 Subject: [PATCH 568/584] ARM: dts: aspeed: g220a: Fix some gpio The NCSI_BMC_R_SEL and EN_NCSI_SWITCH_N should be active-high Signed-off-by: John Wang Reviewed-by: Joel Stanley Link: https://lore.kernel.org/r/20201211040002.1030-2-wangzhiqiang.bj@bytedance.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts index 1f415e62fbde..5ef88c377358 100644 --- a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts +++ b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts @@ -905,14 +905,14 @@ &gpio { pin_gpio_i3 { gpio-hog; - gpios = ; + gpios = ; output-low; line-name = "NCSI_BMC_R_SEL"; }; pin_gpio_b6 { gpio-hog; - gpios = ; + gpios = ; output-low; line-name = "EN_NCSI_SWITCH_N"; }; From 13177f6ed3ea380011cea8a2f798c918e1ffc436 Mon Sep 17 00:00:00 2001 From: Ryan Sie Date: Mon, 21 Dec 2020 05:43:15 -0800 Subject: [PATCH 569/584] ARM: dts: aspeed: Add Supermicro x11spi BMC machine The x11spi is a server platform with an ASPEED AST2500 BMC. Signed-off-by: Ryan Sie Link: https://lore.kernel.org/r/20201221134315.5544-1-RyanS@supermicro.com.tw Signed-off-by: Joel Stanley --- arch/arm/boot/dts/Makefile | 3 +- .../boot/dts/aspeed-bmc-supermicro-x11spi.dts | 137 ++++++++++++++++++ 2 files changed, 139 insertions(+), 1 deletion(-) create mode 100644 arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 5271820a5380..d90bc4eeeb9a 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1435,4 +1435,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-opp-witherspoon.dtb \ aspeed-bmc-opp-zaius.dtb \ aspeed-bmc-portwell-neptune.dtb \ - aspeed-bmc-quanta-q71l.dtb + aspeed-bmc-quanta-q71l.dtb \ + aspeed-bmc-supermicro-x11spi.dtb diff --git a/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts b/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts new file mode 100644 index 000000000000..bc16ad2b5c80 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts @@ -0,0 +1,137 @@ +// SPDX-License-Identifier: GPL-2.0 +// Copyright (c) 2020 Super Micro Computer, Inc + +/dts-v1/; + +#include "aspeed-g5.dtsi" + +/ { + model = "X11SPI BMC"; + compatible = "supermicro,x11spi-bmc", "aspeed,ast2500"; + + chosen { + stdout-path = &uart5; + bootargs = "earlyprintk"; + }; + + memory@80000000 { + reg = <0x80000000 0x20000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + vga_memory: framebuffer@7f000000 { + no-map; + reg = <0x7f000000 0x01000000>; + }; + }; + + iio-hwmon { + compatible = "iio-hwmon"; + io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, + <&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>, + <&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>, + <&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>; + }; + +}; + +&gpio { + status = "okay"; +}; + +&fmc { + status = "okay"; + flash@0 { + status = "okay"; + m25p,fast-read; + label = "bmc"; +#include "openbmc-flash-layout.dtsi" + }; +}; + +&spi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; + + flash@0 { + status = "okay"; + m25p,fast-read; + label = "pnor"; + }; +}; + +&uart5 { + status = "okay"; +}; + +&mac0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii1_default>; + clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>, + <&syscon ASPEED_CLK_MAC1RCLK>; + clock-names = "MACCLK", "RCLK"; + use-ncsi; +}; + +&mac1 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>; +}; + +&i2c1 { + status = "okay"; +}; + +&i2c2 { + status = "okay"; +}; + +&i2c3 { + status = "okay"; +}; + +&i2c4 { + status = "okay"; +}; + +&i2c5 { + status = "okay"; +}; + +&i2c6 { + status = "okay"; +}; + +&i2c7 { + status = "okay"; +}; + +&i2c13 { + status = "okay"; +}; + +&gfx { + status = "okay"; +}; + +&pinctrl { + aspeed,external-nodes = <&gfx &lhc>; +}; + +&pwm_tacho { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default + &pinctrl_pwm2_default &pinctrl_pwm3_default + &pinctrl_pwm4_default &pinctrl_pwm5_default + &pinctrl_pwm6_default &pinctrl_pwm7_default>; +}; From 326e852f2c20f2389ab80f861d566c9e9a98678b Mon Sep 17 00:00:00 2001 From: George Liu Date: Fri, 25 Dec 2020 09:51:26 +0800 Subject: [PATCH 570/584] ARM: dts: aspeed: inspur-fp5280g2: Add GPIO line names Signed-off-by: George Liu Link: https://lore.kernel.org/r/20201225015126.1416690-1-liuxiwei@inspur.com Signed-off-by: Joel Stanley --- .../boot/dts/aspeed-bmc-inspur-fp5280g2.dts | 33 +++++++++++++++++++ 1 file changed, 33 insertions(+) diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts index 62a3ab4c1866..efe521538d70 100644 --- a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts +++ b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts @@ -204,6 +204,39 @@ }; +&gpio { + gpio-line-names = + /*A0-A7*/ "","","","","","","","", + /*B0-B7*/ "","","front-psu","checkstop","cfam-reset","","","init-ok", + /*C0-C7*/ "","","","","","","","", + /*D0-D7*/ "","","","","","","","", + /*E0-E7*/ "","","","","","","","", + /*F0-F7*/ "ps0-presence","ps1-presence","","","front-memory","","","", + /*G0-G7*/ "","","","","","","","", + /*H0-H7*/ "","","","","front-fan","","","", + /*I0-I7*/ "front-syshealth","front-syshot","mux-gpios","enable-gpios","","","","", + /*J0-J7*/ "","","","","","","","", + /*K0-K7*/ "","","","","","","","", + /*L0-L7*/ "","","","","","","","", + /*M0-M7*/ "","","","","","","","", + /*N0-N7*/ "","","","","","","","", + /*O0-O7*/ "","","","","","","","", + /*P0-P7*/ "","","","","","","","", + /*Q0-Q7*/ "","","","","","","","", + /*R0-R7*/ "","power","trans-gpios","","","","","", + /*S0-S7*/ "","","","","","","","", + /*T0-T7*/ "","","","","","","","", + /*U0-U7*/ "","","","","","","","", + /*V0-V7*/ "","","","","","","","", + /*W0-W7*/ "","","","","","","","", + /*X0-X7*/ "","","","","","","","", + /*Y0-Y7*/ "","","","","","","","", + /*Z0-Z7*/ "","","","","","","","identify", + /*AA0-AA7*/ "clock-gpios","","data-gpios","","","","","", + /*AB0-AB7*/ "","","","","","","","", + /*AC0-AC7*/ "","","","","","","",""; +}; + &fmc { status = "okay"; From 8828af99a161d5854509e02e8774ae7248bf0532 Mon Sep 17 00:00:00 2001 From: George Liu Date: Fri, 25 Dec 2020 09:51:49 +0800 Subject: [PATCH 571/584] ARM: dts: aspeed: inspur-fp5280g2: Add ipsps1 driver power-supply is compatible with Inspur's ipsps1 driver Signed-off-by: George Liu Link: https://lore.kernel.org/r/20201225015149.1416773-1-liuxiwei@inspur.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts index efe521538d70..07593897fc9a 100644 --- a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts +++ b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts @@ -789,12 +789,12 @@ status = "okay"; power-supply@58 { - compatible = "pmbus"; + compatible = "inspur,ipsps1"; reg = <0x58>; }; power-supply@59 { - compatible = "pmbus"; + compatible = "inspur,ipsps1"; reg = <0x59>; }; }; From a5c5168478d78ee1515487d6e1106381e6678f4d Mon Sep 17 00:00:00 2001 From: Eddie James Date: Fri, 11 Dec 2020 11:07:04 -0600 Subject: [PATCH 572/584] ARM: dts: aspeed: Add Everest BMC machine Add the Everest machine powered by an AST2600 chip. Copy the basic configuration from Rainier. Signed-off-by: Eddie James Tested-by: Andrew Geissler Link: https://lore.kernel.org/r/20201211170704.27640-1-eajames@linux.ibm.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts | 775 +++++++++++++++++++ 2 files changed, 776 insertions(+) create mode 100644 arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index d90bc4eeeb9a..17412dc71ecd 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1416,6 +1416,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \ aspeed-bmc-facebook-wedge400.dtb \ aspeed-bmc-facebook-yamp.dtb \ aspeed-bmc-facebook-yosemitev2.dtb \ + aspeed-bmc-ibm-everest.dtb \ aspeed-bmc-ibm-rainier.dtb \ aspeed-bmc-ibm-rainier-4u.dtb \ aspeed-bmc-intel-s2600wf.dtb \ diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts new file mode 100644 index 000000000000..6bd876657bb8 --- /dev/null +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts @@ -0,0 +1,775 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +// Copyright 2020 IBM Corp. +/dts-v1/; + +#include "aspeed-g6.dtsi" +#include +#include +#include + +/ { + model = "Everest"; + compatible = "ibm,everest-bmc", "aspeed,ast2600"; + + aliases { + i2c100 = &cfam0_i2c0; + i2c101 = &cfam0_i2c1; + i2c110 = &cfam0_i2c10; + i2c111 = &cfam0_i2c11; + i2c112 = &cfam0_i2c12; + i2c113 = &cfam0_i2c13; + i2c114 = &cfam0_i2c14; + i2c115 = &cfam0_i2c15; + i2c202 = &cfam1_i2c2; + i2c203 = &cfam1_i2c3; + i2c210 = &cfam1_i2c10; + i2c211 = &cfam1_i2c11; + i2c214 = &cfam1_i2c14; + i2c215 = &cfam1_i2c15; + i2c216 = &cfam1_i2c16; + i2c217 = &cfam1_i2c17; + i2c300 = &cfam2_i2c0; + i2c301 = &cfam2_i2c1; + i2c310 = &cfam2_i2c10; + i2c311 = &cfam2_i2c11; + i2c312 = &cfam2_i2c12; + i2c313 = &cfam2_i2c13; + i2c314 = &cfam2_i2c14; + i2c315 = &cfam2_i2c15; + i2c402 = &cfam3_i2c2; + i2c403 = &cfam3_i2c3; + i2c410 = &cfam3_i2c10; + i2c411 = &cfam3_i2c11; + i2c414 = &cfam3_i2c14; + i2c415 = &cfam3_i2c15; + i2c416 = &cfam3_i2c16; + i2c417 = &cfam3_i2c17; + + serial4 = &uart5; + + spi10 = &cfam0_spi0; + spi11 = &cfam0_spi1; + spi12 = &cfam0_spi2; + spi13 = &cfam0_spi3; + spi20 = &cfam1_spi0; + spi21 = &cfam1_spi1; + spi22 = &cfam1_spi2; + spi23 = &cfam1_spi3; + spi30 = &cfam2_spi0; + spi31 = &cfam2_spi1; + spi32 = &cfam2_spi2; + spi33 = &cfam2_spi3; + spi40 = &cfam3_spi0; + spi41 = &cfam3_spi1; + spi42 = &cfam3_spi2; + spi43 = &cfam3_spi3; + }; + + chosen { + stdout-path = &uart5; + bootargs = "console=ttyS4,115200n8"; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x40000000>; + }; + + reserved-memory { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + /* LPC FW cycle bridge region requires natural alignment */ + flash_memory: region@b8000000 { + no-map; + reg = <0xb8000000 0x04000000>; /* 64M */ + }; + + /* 48MB region from the end of flash to start of vga memory */ + ramoops@bc000000 { + compatible = "ramoops"; + reg = <0xbc000000 0x180000>; /* 16 * (3 * 0x8000) */ + record-size = <0x8000>; + console-size = <0x8000>; + pmsg-size = <0x8000>; + max-reason = <3>; /* KMSG_DUMP_EMERG */ + }; + + /* VGA region is dictated by hardware strapping */ + vga_memory: region@bf000000 { + no-map; + compatible = "shared-dma-pool"; + reg = <0xbf000000 0x01000000>; /* 16M */ + }; + }; +}; + +&ehci1 { + status = "okay"; +}; + +&emmc_controller { + status = "okay"; +}; + +&pinctrl_emmc_default { + bias-disable; +}; + +&emmc { + status = "okay"; +}; + +&fsim0 { + status = "okay"; + + #address-cells = <2>; + #size-cells = <0>; + + /* + * CFAM Reset is supposed to be active low but pass1 hardware is wired + * active high. + */ + cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>; + + cfam@0,0 { + reg = <0 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <0>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam0_i2c0: i2c-bus@0 { + reg = <0>; /* OMI01 */ + }; + + cfam0_i2c1: i2c-bus@1 { + reg = <1>; /* OMI23 */ + }; + + cfam0_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam0_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam0_i2c12: i2c-bus@c { + reg = <12>; /* OP4A */ + }; + + cfam0_i2c13: i2c-bus@d { + reg = <13>; /* OP4B */ + }; + + cfam0_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam0_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam0_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam0_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam0_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam0_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ0: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub0: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + }; + }; +}; + +&fsi_hub0 { + cfam@1,0 { + reg = <1 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <1>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam1_i2c2: i2c-bus@2 { + reg = <2>; /* OMI45 */ + }; + + cfam1_i2c3: i2c-bus@3 { + reg = <3>; /* OMI67 */ + }; + + cfam1_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam1_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam1_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam1_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + + cfam1_i2c16: i2c-bus@10 { + reg = <16>; /* OP6A */ + }; + + cfam1_i2c17: i2c-bus@11 { + reg = <17>; /* OP6B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam1_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam1_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam1_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam1_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ1: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub1: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; + + cfam@2,0 { + reg = <2 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <2>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam2_i2c0: i2c-bus@0 { + reg = <0>; /* OM01 */ + }; + + cfam2_i2c1: i2c-bus@1 { + reg = <1>; /* OM23 */ + }; + + cfam2_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam2_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam2_i2c12: i2c-bus@c { + reg = <12>; /* OP4A */ + }; + + cfam2_i2c13: i2c-bus@d { + reg = <13>; /* OP4B */ + }; + + cfam2_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam2_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam2_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam2_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam2_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam2_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ2: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub2: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; + + cfam@3,0 { + reg = <3 0>; + #address-cells = <1>; + #size-cells = <1>; + chip-id = <3>; + + scom@1000 { + compatible = "ibm,fsi2pib"; + reg = <0x1000 0x400>; + }; + + i2c@1800 { + compatible = "ibm,fsi-i2c-master"; + reg = <0x1800 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam3_i2c2: i2c-bus@2 { + reg = <2>; /* OM45 */ + }; + + cfam3_i2c3: i2c-bus@3 { + reg = <3>; /* OM67 */ + }; + + cfam3_i2c10: i2c-bus@a { + reg = <10>; /* OP3A */ + }; + + cfam3_i2c11: i2c-bus@b { + reg = <11>; /* OP3B */ + }; + + cfam3_i2c14: i2c-bus@e { + reg = <14>; /* OP5A */ + }; + + cfam3_i2c15: i2c-bus@f { + reg = <15>; /* OP5B */ + }; + + cfam3_i2c16: i2c-bus@10 { + reg = <16>; /* OP6A */ + }; + + cfam3_i2c17: i2c-bus@11 { + reg = <17>; /* OP6B */ + }; + }; + + fsi2spi@1c00 { + compatible = "ibm,fsi2spi"; + reg = <0x1c00 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + cfam3_spi0: spi@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam3_spi1: spi@20 { + reg = <0x20>; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam3_spi2: spi@40 { + reg = <0x40>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + + cfam3_spi3: spi@60 { + reg = <0x60>; + compatible = "ibm,fsi2spi-restricted"; + #address-cells = <1>; + #size-cells = <0>; + + eeprom@0 { + at25,byte-len = <0x80000>; + at25,addr-mode = <4>; + at25,page-size = <256>; + + compatible = "atmel,at25"; + reg = <0>; + spi-max-frequency = <1000000>; + }; + }; + }; + + sbefifo@2400 { + compatible = "ibm,p9-sbefifo"; + reg = <0x2400 0x400>; + #address-cells = <1>; + #size-cells = <0>; + + fsi_occ3: occ { + compatible = "ibm,p10-occ"; + }; + }; + + fsi_hub3: hub@3400 { + compatible = "fsi-master-hub"; + reg = <0x3400 0x400>; + #address-cells = <2>; + #size-cells = <0>; + + no-scan-on-init; + }; + }; +}; + +/* Legacy OCC numbering (to get rid of when userspace is fixed) */ +&fsi_occ0 { + reg = <1>; +}; + +&fsi_occ1 { + reg = <2>; +}; + +&fsi_occ2 { + reg = <3>; +}; + +&fsi_occ3 { + reg = <4>; +}; + +&ibt { + status = "okay"; +}; + +&vuart1 { + status = "okay"; +}; + +&vuart2 { + status = "okay"; +}; + +&lpc_ctrl { + status = "okay"; + memory-region = <&flash_memory>; +}; + +&kcs4 { + compatible = "openbmc,mctp-lpc"; + status = "okay"; +}; + +&mac2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii3_default>; + clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>, + <&syscon ASPEED_CLK_MAC3RCLK>; + clock-names = "MACCLK", "RCLK"; + use-ncsi; +}; + +&mac3 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rmii4_default>; + clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>, + <&syscon ASPEED_CLK_MAC4RCLK>; + clock-names = "MACCLK", "RCLK"; + use-ncsi; +}; + +&xdma { + status = "okay"; + memory-region = <&vga_memory>; +}; From f249e60eb2c708f66520a025ce06701cea5ca7d9 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Wed, 20 Jan 2021 20:40:31 +0100 Subject: [PATCH 573/584] dt-bindings: add ebang vendor prefix Add vendor prefix for Zhejiang Ebang Communication Co., Ltd. Signed-off-by: Michael Walle Link: https://lore.kernel.org/r/20210120194033.26970-2-michael@walle.cc Acked-by: Rob Herring Signed-off-by: Michal Simek --- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index 041ae90b0d8f..f21fce7fdff6 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -311,6 +311,8 @@ patternProperties: description: Dyna-Image "^ea,.*": description: Embedded Artists AB + "^ebang,.*": + description: Zhejiang Ebang Communication Co., Ltd "^ebs-systart,.*": description: EBS-SYSTART GmbH "^ebv,.*": From 12e6d3eb8e0a8d8cc2b1156af9efb998f0f21941 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Wed, 20 Jan 2021 20:40:32 +0100 Subject: [PATCH 574/584] dt-bindings: arm: add Ebang EBAZ4205 board Add the Ebang EBAZ4205 board to the Zynq-7000 board category. Signed-off-by: Michael Walle Link: https://lore.kernel.org/r/20210120194033.26970-3-michael@walle.cc Signed-off-by: Michal Simek --- Documentation/devicetree/bindings/arm/xilinx.yaml | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/arm/xilinx.yaml b/Documentation/devicetree/bindings/arm/xilinx.yaml index e0c6787f6e94..aaca69d0199f 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.yaml +++ b/Documentation/devicetree/bindings/arm/xilinx.yaml @@ -22,6 +22,7 @@ properties: - adapteva,parallella - digilent,zynq-zybo - digilent,zynq-zybo-z7 + - ebang,ebaz4205 - xlnx,zynq-cc108 - xlnx,zynq-zc702 - xlnx,zynq-zc706 From 00c2747814cc0067c7603c06dcef26a583cfe489 Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Wed, 20 Jan 2021 20:40:33 +0100 Subject: [PATCH 575/584] ARM: dts: add Ebang EBAZ4205 device tree The Ebang EBAZ4205 is a simple board based on the Xilinx Zynq-7000 SoC. Its features are: - one serial port - 256 MB RAM - 128 MB NAND flash - SDcard slot - IP101GA 10/100 Mbit Ethernet PHY (connected to PL IOs) - two LEDs (connected to PL IOs) - one Push Button (connect to PL IOs) - (optional) RTC - (optional) Input voltage supervisor The NAND flash is not supported in mainline linux yet. Unfortunately, the PHY is connected via the PL, thus for working ethernet the FPGA has to be configured. Also, depending on the board variant, the PHY has no external crystal and its clock needs to be driven by the PL. FCLK3 is used for this and is kept enabled. Signed-off-by: Michael Walle Link: https://lore.kernel.org/r/20210120194033.26970-4-michael@walle.cc Signed-off-by: Michal Simek --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/zynq-ebaz4205.dts | 109 ++++++++++++++++++++++++++++ 2 files changed, 110 insertions(+) create mode 100644 arch/arm/boot/dts/zynq-ebaz4205.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 3d1ea0b25168..2cbb4e9a6dfa 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -1307,6 +1307,7 @@ dtb-$(CONFIG_ARCH_VT8500) += \ wm8850-w70v2.dtb dtb-$(CONFIG_ARCH_ZYNQ) += \ zynq-cc108.dtb \ + zynq-ebaz4205.dtb \ zynq-microzed.dtb \ zynq-parallella.dtb \ zynq-zc702.dtb \ diff --git a/arch/arm/boot/dts/zynq-ebaz4205.dts b/arch/arm/boot/dts/zynq-ebaz4205.dts new file mode 100644 index 000000000000..e802d4ae8804 --- /dev/null +++ b/arch/arm/boot/dts/zynq-ebaz4205.dts @@ -0,0 +1,109 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 2021 Michael Walle + */ +/dts-v1/; +/include/ "zynq-7000.dtsi" + +/ { + model = "Ebang EBAZ4205"; + compatible = "ebang,ebaz4205", "xlnx,zynq-7000"; + + aliases { + ethernet0 = &gem0; + serial0 = &uart1; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x10000000>; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&clkc { + ps-clk-frequency = <33333333>; + fclk-enable = <8>; +}; + +&gem0 { + status = "okay"; + phy-mode = "mii"; + phy-handle = <&phy>; + + /* PHY clock */ + assigned-clocks = <&clkc 18>; + assigned-clock-rates = <25000000>; + + phy: ethernet-phy@0 { + reg = <0>; + }; +}; + +&pinctrl0 { + pinctrl_sdhci0_default: sdhci0-default { + mux { + groups = "sdio0_2_grp"; + function = "sdio0"; + }; + + conf { + groups = "sdio0_2_grp"; + io-standard = <3>; + slew-rate = <0>; + bias-disable; + }; + + mux-cd { + groups = "gpio0_34_grp"; + function = "sdio0_cd"; + }; + + conf-cd { + groups = "gpio0_34_grp"; + io-standard = <3>; + slew-rate = <0>; + bias-high-impedance; + bias-pull-up; + }; + }; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_4_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_4_grp"; + io-standard = <3>; + slew-rate = <0>; + }; + + conf-rx { + pins = "MIO25"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO24"; + bias-disable; + }; + }; +}; + +&sdhci0 { + status = "okay"; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci0_default>; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; +}; From 10d43c861476978389e370eed177ba8a18f8146c Mon Sep 17 00:00:00 2001 From: Michael Walle Date: Mon, 1 Feb 2021 14:30:00 +0100 Subject: [PATCH 576/584] ARM: dts: ebaz4205: add pinctrl entries for switches Add the pinctrl entries for the GPIOs which are connected to the push buttons on this board. Signed-off-by: Michael Walle Link: https://lore.kernel.org/r/20210201133000.23402-1-michael@walle.cc Signed-off-by: Michal Simek --- arch/arm/boot/dts/zynq-ebaz4205.dts | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/arch/arm/boot/dts/zynq-ebaz4205.dts b/arch/arm/boot/dts/zynq-ebaz4205.dts index e802d4ae8804..b0b836aedd76 100644 --- a/arch/arm/boot/dts/zynq-ebaz4205.dts +++ b/arch/arm/boot/dts/zynq-ebaz4205.dts @@ -43,7 +43,30 @@ }; }; +&gpio0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio0_default>; +}; + &pinctrl0 { + pinctrl_gpio0_default: gpio0-default { + mux { + groups = "gpio0_20_grp", "gpio0_32_grp"; + function = "gpio0"; + }; + + conf { + groups = "gpio0_20_grp", "gpio0_32_grp"; + io-standard = <3>; + slew-rate = <0>; + }; + + conf-pull-up { + pins = "MIO20", "MIO32"; + bias-disable; + }; + }; + pinctrl_sdhci0_default: sdhci0-default { mux { groups = "sdio0_2_grp"; From 9cc5c6c1567cb46bca1362c6e1f66edbeb3478bc Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Mon, 1 Feb 2021 14:16:12 +0100 Subject: [PATCH 577/584] dt-bindings: arm: xilinx: Add missing Zturn boards Add missing DT compatible strings for Zturn boards. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/f6f642d75c1b1160ed78f6de0a2944ab64017691.1612185370.git.michal.simek@xilinx.com Acked-by: Rob Herring --- Documentation/devicetree/bindings/arm/xilinx.yaml | 2 ++ 1 file changed, 2 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/xilinx.yaml b/Documentation/devicetree/bindings/arm/xilinx.yaml index aaca69d0199f..05217537fb0c 100644 --- a/Documentation/devicetree/bindings/arm/xilinx.yaml +++ b/Documentation/devicetree/bindings/arm/xilinx.yaml @@ -23,6 +23,8 @@ properties: - digilent,zynq-zybo - digilent,zynq-zybo-z7 - ebang,ebaz4205 + - myir,zynq-zturn-v5 + - myir,zynq-zturn - xlnx,zynq-cc108 - xlnx,zynq-zc702 - xlnx,zynq-zc706 From 99fa80c3de159a612f5f5d36bc0e6aae3d42fd2f Mon Sep 17 00:00:00 2001 From: Konstantin Aladyshev Date: Wed, 27 Jan 2021 21:23:26 +0300 Subject: [PATCH 578/584] ARM: dts: aspeed: amd-ethanolx: Enable secondary LPC snooping address AMD EthanolX CRB uses 2-byte POST codes which are sent to ports 0x80/0x81. Currently ASPEED controller snoops only 0x80 port and therefore captures only the lower byte of each POST code. Enable secondary LPC snooping address to capture the higher byte of POST codes. Signed-off-by: Konstantin Aladyshev Reviewed-by: Andrew Jeffery Link: https://lore.kernel.org/r/20210127182326.424-1-aladyshev22@gmail.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts b/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts index 96ff0aea64e5..ac2d04cfaf2f 100644 --- a/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts +++ b/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts @@ -218,7 +218,7 @@ &lpc_snoop { status = "okay"; - snoop-ports = <0x80>; + snoop-ports = <0x80>, <0x81>; }; &lpc_ctrl { From 286a596da2937d292828927a2b2ade4e03188f6c Mon Sep 17 00:00:00 2001 From: Ben Pai Date: Thu, 21 Jan 2021 15:31:46 +0800 Subject: [PATCH 579/584] ARM: dts: aspeed: mowgli: Add i2c rtc device This system uses a rx8900 compatible rtc device. Signed-off-by: Ben Pai Link: https://lore.kernel.org/r/20210121073146.28217-1-Ben_Pai@wistron.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts b/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts index b648e468e9db..8503152faaf0 100644 --- a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts +++ b/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts @@ -582,6 +582,11 @@ /* TMP275A */ /* TMP275A */ + rtc@32 { + compatible = "epson,rx8900"; + reg = <0x32>; + }; + tmp275@48 { compatible = "ti,tmp275"; reg = <0x48>; From a74c6525f12f35a5af529ff057e63cfdc461704c Mon Sep 17 00:00:00 2001 From: Ryan Chen Date: Fri, 9 Oct 2020 10:49:37 +0800 Subject: [PATCH 580/584] ARM: dts: aspeed: ast2600evb: Add enable ehci and uhci Signed-off-by: Ryan Chen Link: https://lore.kernel.org/r/20201009024937.11246-4-ryan_chen@aspeedtech.com Signed-off-by: Joel Stanley --- arch/arm/boot/dts/aspeed-ast2600-evb.dts | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed-ast2600-evb.dts index 89be13197780..2772796e215e 100644 --- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts +++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts @@ -237,3 +237,11 @@ &fsim0 { status = "okay"; }; + +&ehci1 { + status = "okay"; +}; + +&uhci { + status = "okay"; +}; From 0109a17564fc753d8769a1b8d76db3dba17b959b Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Thu, 17 Dec 2020 23:43:38 +0900 Subject: [PATCH 581/584] arm: dts: visconti: Add DT support for Toshiba Visconti5 GPIO driver Add the GPIO node in Toshiba Visconti5 SoC-specific DT file. And enable the GPIO node in TMPV7708 RM main board's board-specific DT file. Signed-off-by: Nobuhiro Iwamatsu Reviewed-by: Punit Agrawal Acked-by: Linus Walleij Signed-off-by: Bartosz Golaszewski --- arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts | 4 ++++ arch/arm64/boot/dts/toshiba/tmpv7708.dtsi | 11 +++++++++++ 2 files changed, 15 insertions(+) diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts index 37da418393e0..2407b2d89c1e 100644 --- a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts +++ b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts @@ -46,3 +46,7 @@ status = "okay"; clocks = <&wdt_clk>; }; + +&gpio { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi index c360e68bef1d..4264f3e6ac9c 100644 --- a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi +++ b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi @@ -163,6 +163,17 @@ reg = <0 0x24190000 0 0x10000>; }; + gpio: gpio@28020000 { + compatible = "toshiba,gpio-tmpv7708"; + reg = <0 0x28020000 0 0x1000>; + #gpio-cells = <0x2>; + gpio-ranges = <&pmux 0 0 32>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + interrupt-parent = <&gic>; + }; + uart0: serial@28200000 { compatible = "arm,pl011", "arm,primecell"; reg = <0 0x28200000 0 0x1000>; From 19e1f484a6bb452d28d79cf41f280cdfde3176a9 Mon Sep 17 00:00:00 2001 From: Michal Simek Date: Wed, 10 Feb 2021 11:10:25 +0100 Subject: [PATCH 582/584] dt-bindings: spi: zynq: Convert Zynq QSPI binding to yaml Convert spi-zynq-qspi.txt to yaml. Signed-off-by: Michal Simek Link: https://lore.kernel.org/r/4ece21a7e9691ed1e775fd6b0b4046b1562e44bd.1612951821.git.michal.simek@xilinx.com Reviewed-by: Rob Herring --- .../devicetree/bindings/spi/spi-zynq-qspi.txt | 25 -------- .../bindings/spi/xlnx,zynq-qspi.yaml | 59 +++++++++++++++++++ MAINTAINERS | 1 + 3 files changed, 60 insertions(+), 25 deletions(-) delete mode 100644 Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt create mode 100644 Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml diff --git a/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt b/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt deleted file mode 100644 index 16b734ad3102..000000000000 --- a/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt +++ /dev/null @@ -1,25 +0,0 @@ -Xilinx Zynq QSPI controller Device Tree Bindings -------------------------------------------------------------------- - -Required properties: -- compatible : Should be "xlnx,zynq-qspi-1.0". -- reg : Physical base address and size of QSPI registers map. -- interrupts : Property with a value describing the interrupt - number. -- clock-names : List of input clock names - "ref_clk", "pclk" - (See clock bindings for details). -- clocks : Clock phandles (see clock bindings for details). - -Optional properties: -- num-cs : Number of chip selects used. - -Example: - qspi: spi@e000d000 { - compatible = "xlnx,zynq-qspi-1.0"; - reg = <0xe000d000 0x1000>; - interrupt-parent = <&intc>; - interrupts = <0 19 4>; - clock-names = "ref_clk", "pclk"; - clocks = <&clkc 10>, <&clkc 43>; - num-cs = <1>; - }; diff --git a/Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml b/Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml new file mode 100644 index 000000000000..1f1c40a9f320 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/spi/xlnx,zynq-qspi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx Zynq QSPI controller + +description: + The Xilinx Zynq QSPI controller is used to access multi-bit serial flash + memory devices. + +allOf: + - $ref: "spi-controller.yaml#" + +maintainers: + - Michal Simek + +# Everything else is described in the common file +properties: + compatible: + const: xlnx,zynq-qspi-1.0 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: reference clock + - description: peripheral clock + + clock-names: + items: + - const: ref_clk + - const: pclk + +required: + - compatible + - reg + - interrupts + - clocks + - clock-names + +unevaluatedProperties: false + +examples: + - | + spi@e000d000 { + compatible = "xlnx,zynq-qspi-1.0"; + reg = <0xe000d000 0x1000>; + interrupt-parent = <&intc>; + interrupts = <0 19 4>; + clock-names = "ref_clk", "pclk"; + clocks = <&clkc 10>, <&clkc 43>; + num-cs = <1>; + }; diff --git a/MAINTAINERS b/MAINTAINERS index 546aa66428c9..e494b061dcd1 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -2766,6 +2766,7 @@ W: http://wiki.xilinx.com T: git https://github.com/Xilinx/linux-xlnx.git F: Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml F: Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml +F: Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml F: arch/arm/mach-zynq/ F: drivers/block/xsysace.c F: drivers/clocksource/timer-cadence-ttc.c From be6ce1cd4d573230ab34173d7c527948e31036a8 Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 12 Feb 2021 17:26:39 +0100 Subject: [PATCH 583/584] ARM: dts: aspeed: fix PCA95xx GPIO expander properties on Portwell The PCA95xx GPIO expander requires GPIO controller properties to operate properly. Signed-off-by: Krzysztof Kozlowski Acked-by: Joel Stanley Link: https://lore.kernel.org/r/20210212162640.66677-1-krzk@kernel.org' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts index 4a1ca8f5b6a7..03c161493ffc 100644 --- a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts +++ b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts @@ -121,6 +121,8 @@ pca9555@27 { compatible = "nxp,pca9555"; reg = <0x27>; + gpio-controller; + #gpio-cells = <2>; }; }; From 14bd96946377148cb6e7dd7ce55ecc5128a92d7b Mon Sep 17 00:00:00 2001 From: Krzysztof Kozlowski Date: Fri, 12 Feb 2021 17:26:40 +0100 Subject: [PATCH 584/584] ARM: dts: aspeed: align GPIO hog names with dtschema dtschema for pca95xx expects GPIO hogs to end with 'hog' suffix. Signed-off-by: Krzysztof Kozlowski Link: https://lore.kernel.org/r/20210212162640.66677-2-krzk@kernel.org' Signed-off-by: Arnd Bergmann --- arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts | 2 +- arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts | 16 ++++++++-------- 2 files changed, 9 insertions(+), 9 deletions(-) diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts index 72de21f7c941..6c9804d2f3b4 100644 --- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts +++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts @@ -580,7 +580,7 @@ gpio-controller; #gpio-cells = <2>; - smbus0 { + smbus0-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts index cb85168f6761..577c211c469e 100644 --- a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts +++ b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts @@ -827,7 +827,7 @@ gpio-controller; #gpio-cells = <2>; - smbus0 { + smbus0-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -852,7 +852,7 @@ gpio-controller; #gpio-cells = <2>; - smbus1 { + smbus1-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -900,7 +900,7 @@ gpio-controller; #gpio-cells = <2>; - smbus2 { + smbus2-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -925,7 +925,7 @@ gpio-controller; #gpio-cells = <2>; - smbus3 { + smbus3-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -992,7 +992,7 @@ gpio-controller; #gpio-cells = <2>; - smbus4 { + smbus4-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -1017,7 +1017,7 @@ gpio-controller; #gpio-cells = <2>; - smbus5 { + smbus5-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -1065,7 +1065,7 @@ gpio-controller; #gpio-cells = <2>; - smbus6 { + smbus6-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high; @@ -1090,7 +1090,7 @@ gpio-controller; #gpio-cells = <2>; - smbus7 { + smbus7-hog { gpio-hog; gpios = <4 GPIO_ACTIVE_HIGH>; output-high;