ARM: SoC devicetree updates for v5.12

After the last release contained a surprising amount of new 32-bit machines, this time two thirds of the code changes are for 64-bit. The usual updates to existing files include: - Device tree compiler warning fixes for Berlin, Renesas, SoCFPGA, nomadik, stm32, Allwinner, TI Keystone - Support for additional devices on existing machines on Renesas, SoCFPGA, at91, hisilicon, OMAP, Tegra, TI K3, Allwinner, Broadcom, ux500, Mediatek, Marvell Armada, Marvell MMP, ZynqMP, AMLogic, Qualcomm, i.MX, Layerscape, Actions, ASpeed, Toshiba - Cleanups and minor fixes for Renesas, at91, mstar, ux500, Samsung, stm32, Tegra, Broadcom, Mediatek, Marvell MMP, AMLogic, Qualcomm, i.MX, Rockchip, ASpeed, Zynq Only three new SoCs this time, but a number of boards across: Renesas: - Two Beacon EmbeddedWorks boards (RZ/G2H and RZ/G2N based) Intel SoCFPGA: - eASIC N5X board (N5X) ST-Ericsson Ux500: - Samsung GT-I9070 (Janice) phone (u8500) TI OMAP: - MYIR Tech Limited development board (AM335X) Allwinner/sunxi: - SL631 Action Camera (V3) - PineTab Early Adopter tablet (A64) Broadcom: - BCM4906/BCM4908 networking chip - Netgear R8000P router (BCM5906) AMLogic: - Hardkernel ODROID-HC4 development board (SM1) - Beelink GS-King-X TV Box (S922X) Qualcomm: - Snapdragon 888 / SM8350 high-end phone SoC - Qualcomm SDX55 5G modem as standalone SoC - Snapdragon MTP reference board (SM8350) - Snapdragon MTP reference board (SDX55) - Sony Kitakami phones: Xperia Z3+/Z4/Z5 (APQ8094) - Alcatel Idol 3 phone (MSM8916) - ASUS Zenfone 2 Laser phone (MSM8916) - BQ Aquaris X5 aka Longcheer L8910 phone (MSM8916) - OnePlus6 phone (SDM845) - OnePlus6T phone (SDM845) - Alfa Network AP120C-AC access point (IPQ4018) NXP i.MX6 (32-bit): - Plymovent BAS base system controller for filter systems (imx6dl) - Protonic MVT industrial touchscreen terminals (imx6dl) - Protonic PRTI6G reference board (imx6ul) - Kverneland UT1, UT1Q, UT1P, TGO agricultural terminals (imx6q/dl/qp) NXP i.MX8 (64-bit) - Beacon i.MX8M Nano development kit (imx8mn) - Boundary Devices i.MX8MM Nitrogen SBC (imx8mm) - Gateworks Venice i.MX 8M Mini Development Kits (imx8mm) - phyBOARD-Pollux-i.MX8MP (imx8mp) - Purism Librem5 Evergreen phone (imx8mp) - Kontron SMARC-sAL28 system-on-module(imx8mp) Rockchip: - NanoPi M4B Single-board computer (RK3399) - Radxa Rock Pi E router SBC (RK3328) ASpeed: - Ampere Mt. Jade, a BMC for an x86 server (AST2500) - IBM Everest, a BMC for a Power10 server (AST2600) - Supermicro x11spi, a BMC for an ARM server (AST2500) Zynq: - Ebang EBAZ4205, FPGA board (Zynq-7000) - ZynqMP zcu104 revC reference platform (ZynqMP) Signed-off-by: Arnd Bergmann <arnd@arndb.de> -----BEGIN PGP SIGNATURE----- iQIzBAABCgAdFiEEiK/NIGsWEZVxh/FrYKtH/8kJUicFAmAppIsACgkQYKtH/8kJ Uif/aBAA0lMYr+WRF9STUC/4u57e+QO7m53bahyO8mniX9raORRy4NxFwpDECXgP s9D/z7aBEojhK5vucsT6Ne5k13udRoI+hH/67t6NHxDod74pHcGJPVWuqXQRuoR+ 9qtm+UUJb+BMZpb2oFSA1KIfnp8GoDKd1jEhCRu3DP1YMoOD/KgZGjbOcBOkqelo EoFHyFhu0qzuDTOO2LgjoW0IYvY48+nzLEPhkBlGPMI7ZMnVPBC4vemowq4prFM/ VknK+AgX8gR2dv8izygQxSVorhEbFrLqlbRCk1AvXDh2EmOGj+8LRVTyA9acZsHl nLqpgPuTc+V8NBPgiHP+DVxRI/DY5mqMMhMj8KIAY8fpH1fY+9CSxeGid8R7LMAQ rTplXr3AHRU4a3rvD5H9GF/WmHKUgcaEE5I9nABzGQW1nFxTPxAYi/YhzNL7y+GZ /em/G+K2zCLANjd4Ij8eyMu6dJv5NBsL5yWhBpkUg/+PLM+0DzYthD9dZ0u11fYf 9b3pW/cM7xw6DL1TRsdVGTE+Y8IsW00RYDKC/7nwKrrtHQ201tIevSYeWNKysMes 2lAuGnUIOquSd/OBjo9a1xGECqYLV95k7fk0juoSsOqzYVnDTt7wDx4W+MI9pwix wVrt0lkRnebgRToioeEPQG0WWitQ1ZkMOWZU4jYiZ2cIXyVEMJ8= =RIJK -----END PGP SIGNATURE----- Merge tag 'arm-dt-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC devicetree updates from Arnd Bergmann: "After the last release contained a surprising amount of new 32-bit machines, this time two thirds of the code changes are for 64-bit. The usual updates to existing files include: - Device tree compiler warning fixes for Berlin, Renesas, SoCFPGA, nomadik, stm32, Allwinner, TI Keystone - Support for additional devices on existing machines on Renesas, SoCFPGA, at91, hisilicon, OMAP, Tegra, TI K3, Allwinner, Broadcom, ux500, Mediatek, Marvell Armada, Marvell MMP, ZynqMP, AMLogic, Qualcomm, i.MX, Layerscape, Actions, ASpeed, Toshiba - Cleanups and minor fixes for Renesas, at91, mstar, ux500, Samsung, stm32, Tegra, Broadcom, Mediatek, Marvell MMP, AMLogic, Qualcomm, i.MX, Rockchip, ASpeed, Zynq Only three new SoCs this time, but a number of boards across: Renesas: - Two Beacon EmbeddedWorks boards (RZ/G2H and RZ/G2N based) Intel SoCFPGA: - eASIC N5X board (N5X) ST-Ericsson Ux500: - Samsung GT-I9070 (Janice) phone (u8500) TI OMAP: - MYIR Tech Limited development board (AM335X) Allwinner/sunxi: - SL631 Action Camera (V3) - PineTab Early Adopter tablet (A64) Broadcom: - BCM4906 networking chip - Netgear R8000P router (BCM4906) AMLogic: - Hardkernel ODROID-HC4 development board (SM1) - Beelink GS-King-X TV Box (S922X) Qualcomm: - Snapdragon 888 / SM8350 high-end phone SoC - Qualcomm SDX55 5G modem as standalone SoC - Snapdragon MTP reference board (SM8350) - Snapdragon MTP reference board (SDX55) - Sony Kitakami phones: Xperia Z3+/Z4/Z5 (APQ8094) - Alcatel Idol 3 phone (MSM8916) - ASUS Zenfone 2 Laser phone (MSM8916) - BQ Aquaris X5 aka Longcheer L8910 phone (MSM8916) - OnePlus6 phone (SDM845) - OnePlus6T phone (SDM845) - Alfa Network AP120C-AC access point (IPQ4018) NXP i.MX6 (32-bit): - Plymovent BAS base system controller for filter systems (imx6dl) - Protonic MVT industrial touchscreen terminals (imx6dl) - Protonic PRTI6G reference board (imx6ul) - Kverneland UT1, UT1Q, UT1P, TGO agricultural terminals (imx6q/dl/qp) NXP i.MX8 (64-bit) - Beacon i.MX8M Nano development kit (imx8mn) - Boundary Devices i.MX8MM Nitrogen SBC (imx8mm) - Gateworks Venice i.MX 8M Mini Development Kits (imx8mm) - phyBOARD-Pollux-i.MX8MP (imx8mp) - Purism Librem5 Evergreen phone (imx8mp) - Kontron SMARC-sAL28 system-on-module(imx8mp) Rockchip: - NanoPi M4B Single-board computer (RK3399) - Radxa Rock Pi E router SBC (RK3328) ASpeed: - Ampere Mt. Jade, a BMC for an x86 server (AST2500) - IBM Everest, a BMC for a Power10 server (AST2600) - Supermicro x11spi, a BMC for an ARM server (AST2500) Zynq: - Ebang EBAZ4205, FPGA board (Zynq-7000) - ZynqMP zcu104 revC reference platform (ZynqMP)" * tag 'arm-dt-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (584 commits) ARM: dts: aspeed: align GPIO hog names with dtschema ARM: dts: aspeed: fix PCA95xx GPIO expander properties on Portwell dt-bindings: spi: zynq: Convert Zynq QSPI binding to yaml arm: dts: visconti: Add DT support for Toshiba Visconti5 GPIO driver ARM: dts: aspeed: ast2600evb: Add enable ehci and uhci ARM: dts: aspeed: mowgli: Add i2c rtc device ARM: dts: aspeed: amd-ethanolx: Enable secondary LPC snooping address dt-bindings: arm: xilinx: Add missing Zturn boards ARM: dts: ebaz4205: add pinctrl entries for switches ARM: dts: add Ebang EBAZ4205 device tree dt-bindings: arm: add Ebang EBAZ4205 board dt-bindings: add ebang vendor prefix ARM: dts: aspeed: Add Everest BMC machine ARM: dts: aspeed: inspur-fp5280g2: Add ipsps1 driver ARM: dts: aspeed: inspur-fp5280g2: Add GPIO line names ARM: dts: aspeed: Add Supermicro x11spi BMC machine ARM: dts: aspeed: g220a: Fix some gpio ARM: dts: aspeed: g220a: Enable ipmb ARM: dts: aspeed: rainier: Add eMMC clock phase compensation ARM: dts: aspeed: Add LCLK to lpc-snoop ...
2021-02-20 18:34:53 -08:00 · 2021-02-20 18:34:53 -08:00 · 82851fce61
parent 56bf6fc266 14bd969463
commit 82851fce61
569 changed files with 31089 additions and 4434 deletions
--- a/Documentation/devicetree/bindings/arm/amlogic.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic.yaml
@ -151,6 +151,7 @@ properties:
      - description: Boards with the Amlogic Meson G12B S922X SoC
        items:
          - enum:
+              - azw,gsking-x
              - azw,gtking
              - azw,gtking-pro
              - hardkernel,odroid-n2
@ -163,9 +164,10 @@ properties:
      - description: Boards with the Amlogic Meson SM1 S905X3/D3/Y3 SoC
        items:
          - enum:
-              - seirobotics,sei610
-              - khadas,vim3l
              - hardkernel,odroid-c4
+              - hardkernel,odroid-hc4
+              - khadas,vim3l
+              - seirobotics,sei610
          - const: amlogic,sm1

      - description: Boards with the Amlogic Meson A1 A113L SoC
--- a/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-mx-secbus2.yaml
+++ b/Documentation/devicetree/bindings/arm/amlogic/amlogic,meson-mx-secbus2.yaml
@ -0,0 +1,42 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/arm/amlogic/amlogic,meson-mx-secbus2.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Amlogic Meson8/Meson8b/Meson8m2 SECBUS2 register interface
+
+maintainers:
+  - Martin Blumenstingl <martin.blumenstingl@googlemail.com>
+
+description: |
+  The Meson8/Meson8b/Meson8m2 SoCs have a register bank called SECBUS2 which
+  contains registers for various IP blocks such as pin-controller bits for
+  the BSD_EN and TEST_N GPIOs as well as some AO ARC core control bits.
+  The registers can be accessed directly when not running in "secure mode".
+  When "secure mode" is enabled then these registers have to be accessed
+  through secure monitor calls.
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - amlogic,meson8-secbus2
+          - amlogic,meson8b-secbus2
+      - const: syscon
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    secbus2: system-controller@4000 {
+      compatible = "amlogic,meson8-secbus2", "syscon";
+      reg = <0x4000 0x2000>;
+    };
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm4908.yaml
@ -19,6 +19,8 @@ properties:
    oneOf:
      - description: BCM4906 based boards
        items:
+          - enum:
+              - netgear,r8000p
          - const: brcm,bcm4906
          - const: brcm,bcm4908

--- a/Documentation/devicetree/bindings/arm/cpus.yaml
+++ b/Documentation/devicetree/bindings/arm/cpus.yaml
@ -169,6 +169,7 @@ properties:
      - qcom,kryo385
      - qcom,kryo468
      - qcom,kryo485
+      - qcom,kryo685
      - qcom,scorpion

  enable-method:
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@ -210,6 +210,7 @@ properties:
              - kiebackpeter,imx6q-tpc    # K+P i.MX6 Quad TPC Board
              - kontron,imx6q-samx6i      # Kontron i.MX6 Dual/Quad SMARC Module
              - kosagi,imx6q-novena       # Kosagi Novena Dual/Quad
+              - kvg,vicut1q               # Kverneland UT1Q board
              - logicpd,imx6q-logicpd
              - lwn,display5              # Liebherr Display5 i.MX6 Quad Board
              - lwn,mccmon6               # Liebherr Monitor6 i.MX6 Quad Board
@ -331,6 +332,7 @@ properties:
              - fsl,imx6qp-sabreauto      # i.MX6 Quad Plus SABRE Automotive Board
              - fsl,imx6qp-sabresd        # i.MX6 Quad Plus SABRE Smart Device Board
              - karo,imx6qp-tx6qp         # Ka-Ro electronics TX6QP-8037 Module
+              - kvg,vicutp                # Kverneland UT1P board
              - prt,prtwd3                # Protonic WD3 board
              - wand,imx6qp-wandboard     # Wandboard i.MX6 QuadPlus Board
              - zii,imx6qp-zii-rdu2       # ZII RDU2+ Board
@ -364,7 +366,12 @@ properties:
              - fsl,imx6dl-sabresd        # i.MX6 DualLite SABRE Smart Device Board
              - karo,imx6dl-tx6dl         # Ka-Ro electronics TX6U Modules
              - kontron,imx6dl-samx6i     # Kontron i.MX6 Solo SMARC Module
+              - kvg,victgo                # Kverneland TGO
+              - kvg,vicut1                # Kverneland UT1 board
+              - ply,plybas                # Plymovent BAS board
+              - ply,plym2m                # Plymovent M2M board
              - poslab,imx6dl-savageboard # Poslab SavageBoard Dual
+              - prt,prtmvt                # Protonic MVT board
              - prt,prtrvt                # Protonic RVT board
              - prt,prtvt7                # Protonic VT7 board
              - rex,imx6dl-rex-basic      # Rex Basic i.MX6 Dual Lite Board
@ -488,6 +495,7 @@ properties:
              - karo,imx6ul-tx6ul         # Ka-Ro electronics TXUL-0010 Module
              - kontron,imx6ul-n6310-som  # Kontron N6310 SOM
              - kontron,imx6ul-n6311-som  # Kontron N6311 SOM
+              - prt,prti6g                # Protonic PRTI6G Board
              - technexion,imx6ul-pico-dwarf   # TechNexion i.MX6UL Pico-Dwarf
              - technexion,imx6ul-pico-hobbit  # TechNexion i.MX6UL Pico-Hobbit
              - technexion,imx6ul-pico-pi      # TechNexion i.MX6UL Pico-Pi
@ -670,8 +678,12 @@ properties:
        items:
          - enum:
              - beacon,imx8mm-beacon-kit  # i.MX8MM Beacon Development Kit
+              - boundary,imx8mm-nitrogen8mm  # i.MX8MM Nitrogen Board
              - fsl,imx8mm-ddr4-evk       # i.MX8MM DDR4 EVK Board
              - fsl,imx8mm-evk            # i.MX8MM EVK Board
+              - gw,imx8mm-gw71xx-0x       # i.MX8MM Gateworks Development Kit
+              - gw,imx8mm-gw72xx-0x       # i.MX8MM Gateworks Development Kit
+              - gw,imx8mm-gw73xx-0x       # i.MX8MM Gateworks Development Kit
              - kontron,imx8mm-n801x-som  # i.MX8MM Kontron SL (N801X) SOM
              - variscite,var-som-mx8mm   # i.MX8MM Variscite VAR-SOM-MX8MM module
          - const: fsl,imx8mm
@ -691,6 +703,7 @@ properties:
      - description: i.MX8MN based Boards
        items:
          - enum:
+              - beacon,imx8mn-beacon-kit  # i.MX8MN Beacon Development Kit
              - fsl,imx8mn-ddr4-evk       # i.MX8MN DDR4 EVK Board
              - fsl,imx8mn-evk            # i.MX8MN LPDDR4 EVK Board
          - const: fsl,imx8mn
@ -707,6 +720,12 @@ properties:
              - fsl,imx8mp-evk            # i.MX8MP EVK Board
          - const: fsl,imx8mp

+      - description: PHYTEC phyCORE-i.MX8MP SoM based boards
+        items:
+          - const: phytec,imx8mp-phyboard-pollux-rdk # phyBOARD-Pollux RDK
+          - const: phytec,imx8mp-phycore-som         # phyCORE-i.MX8MP SoM
+          - const: fsl,imx8mp
+
      - description: i.MX8MQ based Boards
        items:
          - enum:
@ -724,6 +743,7 @@ properties:
          - enum:
              - purism,librem5r2          # Purism Librem5 phone "Chestnut"
              - purism,librem5r3          # Purism Librem5 phone "Dogwood"
+              - purism,librem5r4          # Purism Librem5 phone "Evergreen"
          - const: purism,librem5
          - const: fsl,imx8mq

@ -834,10 +854,12 @@ properties:
          Kontron SMARC-sAL28 board on the SMARC Eval Carrier 2.0
        items:
          - enum:
+              - kontron,sl28-var1-ads2
              - kontron,sl28-var2-ads2
              - kontron,sl28-var3-ads2
              - kontron,sl28-var4-ads2
          - enum:
+              - kontron,sl28-var1
              - kontron,sl28-var2
              - kontron,sl28-var3
              - kontron,sl28-var4
@ -848,6 +870,7 @@ properties:
          Kontron SMARC-sAL28 board (on a generic/undefined carrier)
        items:
          - enum:
+              - kontron,sl28-var1
              - kontron,sl28-var2
              - kontron,sl28-var3
              - kontron,sl28-var4
--- a/Documentation/devicetree/bindings/arm/mediatek.yaml
+++ b/Documentation/devicetree/bindings/arm/mediatek.yaml
@ -120,7 +120,9 @@ properties:
          - const: mediatek,mt8183
      - description: Google Krane (Lenovo IdeaPad Duet, 10e,...)
        items:
-          - const: google,krane-sku176
+          - enum:
+              - google,krane-sku0
+              - google,krane-sku176
          - const: google,krane
          - const: mediatek,mt8183

--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@ -40,7 +40,9 @@ description: |
        sdm630
        sdm660
        sdm845
+        sdx55
        sm8250
+        sm8350

  The 'board' element must be one of the following strings:

@ -167,6 +169,11 @@ properties:
              - xiaomi,lavender
          - const: qcom,sdm660

+      - items:
+          - enum:
+              - qcom,sdx55-mtp
+          - const: qcom,sdx55
+
      - items:
          - enum:
              - qcom,ipq6018-cp01-c1
@ -178,6 +185,11 @@ properties:
              - qcom,sm8250-mtp
          - const: qcom,sm8250

+      - items:
+          - enum:
+              - qcom,sm8350-mtp
+          - const: qcom,sm8350
+
 additionalProperties: true

 ...
--- a/Documentation/devicetree/bindings/arm/renesas.yaml
+++ b/Documentation/devicetree/bindings/arm/renesas.yaml
@ -130,6 +130,7 @@ properties:
      - description: RZ/G2N (R8A774B1)
        items:
          - enum:
+              - beacon,beacon-rzg2n # Beacon EmbeddedWorks RZ/G2N Kit
              - hoperun,hihope-rzg2n # HopeRun HiHope RZ/G2N platform
          - const: renesas,r8a774b1

@ -154,6 +155,7 @@ properties:
      - description: RZ/G2H (R8A774E1)
        items:
          - enum:
+              - beacon,beacon-rzg2h # Beacon EmbeddedWorks RZ/G2H Kit
              - hoperun,hihope-rzg2h # HopeRun HiHope RZ/G2H platform
          - const: renesas,r8a774e1

--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@ -467,6 +467,11 @@ properties:
          - const: radxa,rockpi4
          - const: rockchip,rk3399

+      - description: Radxa ROCK Pi E
+        items:
+          - const: radxa,rockpi-e
+          - const: rockchip,rk3328
+
      - description: Radxa ROCK Pi N8
        items:
          - const: radxa,rockpi-n8
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@ -657,7 +657,8 @@ properties:
      - description: Pine64 PineCube
        items:
          - const: pine64,pinecube
-          - const: allwinner,sun8i-s3
+          - const: sochip,s3
+          - const: allwinner,sun8i-v3

      - description: Pine64 PineH64 model A
        items:
@ -683,23 +684,31 @@ properties:
      - description: Pine64 PinePhone Developer Batch (1.0)
        items:
          - const: pine64,pinephone-1.0
+          - const: pine64,pinephone
          - const: allwinner,sun50i-a64

      - description: Pine64 PinePhone Braveheart (1.1)
        items:
          - const: pine64,pinephone-1.1
+          - const: pine64,pinephone
          - const: allwinner,sun50i-a64

      - description: Pine64 PinePhone (1.2)
        items:
          - const: pine64,pinephone-1.2
+          - const: pine64,pinephone
          - const: allwinner,sun50i-a64

-      - description: Pine64 PineTab
+      - description: Pine64 PineTab, Development Sample
        items:
          - const: pine64,pinetab
          - const: allwinner,sun50i-a64

+      - description: Pine64 PineTab, Early Adopter's batch (and maybe later ones)
+        items:
+          - const: pine64,pinetab-early-adopter
+          - const: allwinner,sun50i-a64
+
      - description: Pine64 SoPine Baseboard
        items:
          - const: pine64,sopine-baseboard
@ -777,6 +786,12 @@ properties:
          - const: sinlinx,sina33
          - const: allwinner,sun8i-a33

+      - description: SL631 Action Camera with IMX179
+        items:
+          - const: allwinner,sl631-imx179
+          - const: allwinner,sl631
+          - const: allwinner,sun8i-v3
+
      - description: Tanix TX6
        items:
          - const: oranth,tanix-tx6
--- a/Documentation/devicetree/bindings/arm/tegra.yaml
+++ b/Documentation/devicetree/bindings/arm/tegra.yaml
@ -120,10 +120,18 @@ properties:
        items:
          - const: nvidia,p3668-0000
          - const: nvidia,tegra194
+      - description: Jetson Xavier NX (eMMC)
+        items:
+          - const: nvidia,p3668-0001
+          - const: nvidia,tegra194
      - description: Jetson Xavier NX Developer Kit
        items:
          - const: nvidia,p3509-0000+p3668-0000
          - const: nvidia,tegra194
+      - description: Jetson Xavier NX Developer Kit (eMMC)
+        items:
+          - const: nvidia,p3509-0000+p3668-0001
+          - const: nvidia,tegra194
      - items:
          - enum:
              - nvidia,tegra234-vdk
--- a/Documentation/devicetree/bindings/arm/xilinx.yaml
+++ b/Documentation/devicetree/bindings/arm/xilinx.yaml
@ -22,6 +22,9 @@ properties:
              - adapteva,parallella
              - digilent,zynq-zybo
              - digilent,zynq-zybo-z7
+              - ebang,ebaz4205
+              - myir,zynq-zturn-v5
+              - myir,zynq-zturn
              - xlnx,zynq-cc108
              - xlnx,zynq-zc702
              - xlnx,zynq-zc706
@ -91,6 +94,7 @@ properties:
        items:
          - enum:
              - xlnx,zynqmp-zcu104-revA
+              - xlnx,zynqmp-zcu104-revC
              - xlnx,zynqmp-zcu104-rev1.0
          - const: xlnx,zynqmp-zcu104
          - const: xlnx,zynqmp
@ -107,7 +111,7 @@ properties:
        items:
          - enum:
              - xlnx,zynqmp-zcu111-revA
-              - xlnx,zynqmp-zcu11-rev1.0
+              - xlnx,zynqmp-zcu111-rev1.0
          - const: xlnx,zynqmp-zcu111
          - const: xlnx,zynqmp

--- a/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
+++ b/Documentation/devicetree/bindings/display/panel/panel-simple.yaml
@ -105,26 +105,27 @@ properties:
      - dlc,dlc1010gig
        # Emerging Display Technology Corp. 3.5" QVGA TFT LCD panel
      - edt,et035012dm6
+        # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
+      - edt,et057090dhu
+      - edt,et070080dh6
        # Emerging Display Technology Corp. 480x272 TFT Display with capacitive touch
      - edt,etm043080dh6gp
        # Emerging Display Technology Corp. 480x272 TFT Display
      - edt,etm0430g0dh6
-        # Emerging Display Technology Corp. 5.7" VGA TFT LCD panel
-      - edt,et057090dhu
-        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
-      - edt,etm070080dh6
-        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
-      - edt,etm0700g0dh6
        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
        # Same as ETM0700G0DH6 but with inverted pixel clock.
      - edt,etm070080bdh6
+        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
+        # Same timings as the ETM0700G0DH6, but with resistive touch.
+      - edt,etm070080dh6
        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
        # Same display as the ETM0700G0BDH6, but with changed hardware for the
        # backlight and the touch interface.
      - edt,etm070080edh6
+      - edt,etm0700g0bdh6
        # Emerging Display Technology Corp. WVGA TFT Display with capacitive touch
-        # Same timings as the ETM0700G0DH6, but with resistive touch.
-      - edt,etm070080dh6
+      - edt,etm0700g0dh6
+      - edt,etm0700g0edh6
        # Evervision Electronics Co. Ltd. VGG804821 5.0" WVGA TFT LCD Panel
      - evervision,vgg804821
        # Foxlink Group 5" WVGA TFT LCD panel
@ -173,6 +174,8 @@ properties:
      - koe,tx26d202vm0bwa
        # Kaohsiung Opto-Electronics. TX31D200VM0BAA 12.3" HSXGA LVDS panel
      - koe,tx31d200vm0baa
+        # Kyocera Corporation 7" WVGA (800x480) transmissive color TFT
+      - kyo,tcg070wvlq
        # Kyocera Corporation 12.1" XGA (1024x768) TFT LCD panel
      - kyo,tcg121xglp
        # LeMaker BL035-RGB-002 3.5" QVGA TFT LCD panel
--- a/Documentation/devicetree/bindings/firmware/qcom,scm.txt
+++ b/Documentation/devicetree/bindings/firmware/qcom,scm.txt
@ -22,6 +22,8 @@ Required properties:
 * "qcom,scm-sc7180"
 * "qcom,scm-sdm845"
 * "qcom,scm-sm8150"
+ * "qcom,scm-sm8250"
+ * "qcom,scm-sm8350"
 and:
 * "qcom,scm"
 - clocks: Specifies clocks needed by the SCM interface, if any:
--- a/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml
+++ b/Documentation/devicetree/bindings/gpio/mrvl-gpio.yaml
@ -82,8 +82,7 @@ properties:
  '#gpio-cells':
    const: 2

-  gpio-ranges:
-    maxItems: 1
+  gpio-ranges: true

  interrupts: true

--- a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
+++ b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml
@ -46,10 +46,14 @@ description: |

 properties:
  compatible:
-    enum:
-      - x-powers,axp209-adc
-      - x-powers,axp221-adc
-      - x-powers,axp813-adc
+    oneOf:
+      - const: x-powers,axp209-adc
+      - const: x-powers,axp221-adc
+      - const: x-powers,axp813-adc
+
+      - items:
+          - const: x-powers,axp803-adc
+          - const: x-powers,axp813-adc

  "#io-channel-cells":
    const: 1
--- a/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/allwinner,sun7i-a20-sc-nmi.yaml
@ -29,6 +29,9 @@ properties:
      - items:
          - const: allwinner,sun8i-a83t-r-intc
          - const: allwinner,sun6i-a31-r-intc
+      - items:
+          - const: allwinner,sun8i-v3s-nmi
+          - const: allwinner,sun9i-a80-nmi
      - const: allwinner,sun9i-a80-nmi
      - items:
          - const: allwinner,sun50i-a64-r-intc
--- a/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml
+++ b/Documentation/devicetree/bindings/media/allwinner,sun8i-h3-deinterlace.yaml
@ -19,6 +19,9 @@ properties:
  compatible:
    oneOf:
      - const: allwinner,sun8i-h3-deinterlace
+      - items:
+          - const: allwinner,sun8i-r40-deinterlace
+          - const: allwinner,sun8i-h3-deinterlace
      - items:
          - const: allwinner,sun50i-a64-deinterlace
          - const: allwinner,sun8i-h3-deinterlace
--- a/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml
+++ b/Documentation/devicetree/bindings/media/marvell,mmp2-ccic.yaml
@ -23,6 +23,9 @@ properties:
  interrupts:
    maxItems: 1

+  power-domains:
+    maxItems: 1
+
  port:
    type: object
    additionalProperties: false
@ -75,6 +78,7 @@ additionalProperties: false
 examples:
  - |
    #include <dt-bindings/clock/marvell,mmp2.h>
+    #include <dt-bindings/power/marvell,mmp2.h>

    camera@d420a000 {
      compatible = "marvell,mmp2-ccic";
@ -84,6 +88,7 @@ examples:
      clock-names = "axi";
      #clock-cells = <0>;
      clock-output-names = "mclk";
+      power-domains = <&soc_clocks MMP3_POWER_DOMAIN_CAMERA>;

      port {
        camera0_0: endpoint {
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@ -128,7 +128,6 @@ required:
  - compatible
  - reg
  - interrupts
-  - clocks
  - clock-output-names

 additionalProperties: false
--- a/Documentation/devicetree/bindings/soc/imx/imx8m-soc.yaml
+++ b/Documentation/devicetree/bindings/soc/imx/imx8m-soc.yaml
@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/imx/imx8m-soc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP i.MX8M Series SoC
+
+maintainers:
+  - Alice Guo <alice.guo@nxp.com>
+
+description: |
+  NXP i.MX8M series SoCs contain fuse entries from which SoC Unique ID can be
+  obtained.
+
+select:
+  properties:
+    compatible:
+      contains:
+        enum:
+          - fsl,imx8mm
+          - fsl,imx8mn
+          - fsl,imx8mp
+          - fsl,imx8mq
+  required:
+    - compatible
+
+patternProperties:
+  "^soc@[0-9a-f]+$":
+    type: object
+    properties:
+      compatible:
+        items:
+          - enum:
+              - fsl,imx8mm-soc
+              - fsl,imx8mn-soc
+              - fsl,imx8mp-soc
+              - fsl,imx8mq-soc
+          - const: simple-bus
+
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 1
+
+      ranges: true
+
+      dma-ranges: true
+
+      nvmem-cells:
+        maxItems: 1
+        description: Phandle to the SOC Unique ID provided by a nvmem node
+
+      nvmem-cell-names:
+        const: soc_unique_id
+
+    required:
+      - compatible
+      - nvmem-cells
+      - nvmem-cell-names
+
+    additionalProperties:
+      type: object
+
+additionalProperties: true
+
+examples:
+  - |
+    / {
+        model = "FSL i.MX8MM EVK board";
+        compatible = "fsl,imx8mm-evk", "fsl,imx8mm";
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        soc@0 {
+            compatible = "fsl,imx8mm-soc", "simple-bus";
+            #address-cells = <1>;
+            #size-cells = <1>;
+            ranges = <0x0 0x0 0x0 0x3e000000>;
+            nvmem-cells = <&imx8mm_uid>;
+            nvmem-cell-names = "soc_unique_id";
+        };
+    };
+
+...
--- a/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt
+++ b/Documentation/devicetree/bindings/spi/spi-zynq-qspi.txt
@ -1,25 +0,0 @@
-Xilinx Zynq QSPI controller Device Tree Bindings
-------------------------------------------------------------------
-
-Required properties:
- compatible		: Should be "xlnx,zynq-qspi-1.0".
- reg			: Physical base address and size of QSPI registers map.
- interrupts		: Property with a value describing the interrupt
-			  number.
- clock-names		: List of input clock names - "ref_clk", "pclk"
-			  (See clock bindings for details).
- clocks		: Clock phandles (see clock bindings for details).
-
-Optional properties:
- num-cs		: Number of chip selects used.
-
-Example:
-	qspi: spi@e000d000 {
-		compatible = "xlnx,zynq-qspi-1.0";
-		reg = <0xe000d000 0x1000>;
-		interrupt-parent = <&intc>;
-		interrupts = <0 19 4>;
-		clock-names = "ref_clk", "pclk";
-		clocks = <&clkc 10>, <&clkc 43>;
-		num-cs = <1>;
-	};
--- a/Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml
+++ b/Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml
@ -0,0 +1,59 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/xlnx,zynq-qspi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Zynq QSPI controller
+
+description:
+  The Xilinx Zynq QSPI controller is used to access multi-bit serial flash
+  memory devices.
+
+allOf:
+  - $ref: "spi-controller.yaml#"
+
+maintainers:
+  - Michal Simek <michal.simek@xilinx.com>
+
+# Everything else is described in the common file
+properties:
+  compatible:
+    const: xlnx,zynq-qspi-1.0
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: reference clock
+      - description: peripheral clock
+
+  clock-names:
+    items:
+      - const: ref_clk
+      - const: pclk
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    spi@e000d000 {
+        compatible = "xlnx,zynq-qspi-1.0";
+        reg = <0xe000d000 0x1000>;
+        interrupt-parent = <&intc>;
+        interrupts = <0 19 4>;
+        clock-names = "ref_clk", "pclk";
+        clocks = <&clkc 10>, <&clkc 43>;
+        num-cs = <1>;
+    };
--- a/Documentation/devicetree/bindings/sram/sram.yaml
+++ b/Documentation/devicetree/bindings/sram/sram.yaml
@ -72,6 +72,8 @@ patternProperties:
            - allwinner,sun4i-a10-sram-d
            - allwinner,sun9i-a80-smp-sram
            - allwinner,sun50i-a64-sram-c
+            - amlogic,meson8-ao-arc-sram
+            - amlogic,meson8b-ao-arc-sram
            - amlogic,meson8-smp-sram
            - amlogic,meson8b-smp-sram
            - amlogic,meson-gxbb-scp-shmem
--- a/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
+++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.yaml
@ -17,6 +17,7 @@ properties:
          - qcom,msm8998-dwc3
          - qcom,sc7180-dwc3
          - qcom,sdm845-dwc3
+          - qcom,sdx55-dwc3
      - const: qcom,dwc3

  reg:
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@ -59,6 +59,8 @@ patternProperties:
    description: Aeroflex Gaisler AB
  "^al,.*":
    description: Annapurna Labs
+  "^alcatel,.*":
+    description: Alcatel
  "^allegro,.*":
    description: Allegro DVT
  "^allo,.*":
@ -311,6 +313,8 @@ patternProperties:
    description: Dyna-Image
  "^ea,.*":
    description: Embedded Artists AB
+  "^ebang,.*":
+    description: Zhejiang Ebang Communication Co., Ltd
  "^ebs-systart,.*":
    description: EBS-SYSTART GmbH
  "^ebv,.*":
@ -467,10 +471,10 @@ patternProperties:
    description: Hitex Development Tools
  "^holt,.*":
    description: Holt Integrated Circuits, Inc.
-  "^honeywell,.*":
-    description: Honeywell
  "^honestar,.*":
    description: Honestar Technologies Co., Ltd.
+  "^honeywell,.*":
+    description: Honeywell
  "^hoperun,.*":
    description: Jiangsu HopeRun Software Co., Ltd.
  "^hp,.*":
@ -581,6 +585,8 @@ patternProperties:
    description: Kontron S&T AG
  "^kosagi,.*":
    description: Sutajio Ko-Usagi PTE Ltd.
+  "^kvg,.*":
+    description: Kverneland Group
  "^kyo,.*":
    description: Kyocera Corporation
  "^lacie,.*":
@ -866,6 +872,8 @@ patternProperties:
    description: PLDA
  "^plx,.*":
    description: Broadcom Corporation (formerly PLX Technology)
+  "^ply,.*":
+    description: Plymovent Group BV
  "^pni,.*":
    description: PNI Sensor Corporation
  "^pocketbook,.*":
--- a/Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/qcom-wdt.yaml
@ -18,6 +18,7 @@ properties:
      - qcom,apss-wdt-qcs404
      - qcom,apss-wdt-sc7180
      - qcom,apss-wdt-sdm845
+      - qcom,apss-wdt-sdx55
      - qcom,apss-wdt-sm8150
      - qcom,kpss-timer
      - qcom,kpss-wdt
--- a/3
+++ b/3
@ -2607,9 +2607,11 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti.git
 F:	Documentation/devicetree/bindings/arm/toshiba.yaml
 F:	Documentation/devicetree/bindings/net/toshiba,visconti-dwmac.yaml
 F:	Documentation/devicetree/bindings/pinctrl/toshiba,tmpv7700-pinctrl.yaml
+F:	Documentation/devicetree/bindings/watchdog/toshiba,visconti-wdt.yaml
 F:	arch/arm64/boot/dts/toshiba/
 F:	drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
 F:	drivers/pinctrl/visconti/
+F:	drivers/watchdog/visconti_wdt.c
 N:	visconti

 ARM/UNIPHIER ARCHITECTURE
@ -2697,6 +2699,7 @@ W:	http://wiki.xilinx.com
 T:	git https://github.com/Xilinx/linux-xlnx.git
 F:	Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml
 F:	Documentation/devicetree/bindings/i2c/xlnx,xps-iic-2.00.a.yaml
+F:	Documentation/devicetree/bindings/spi/xlnx,zynq-qspi.yaml
 F:	arch/arm/mach-zynq/
 F:	drivers/block/xsysace.c
 F:	drivers/clocksource/timer-cadence-ttc.c
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@ -459,6 +459,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-pico-hobbit.dtb \
 	imx6dl-pico-nymph.dtb \
 	imx6dl-pico-pi.dtb \
+	imx6dl-plybas.dtb \
+	imx6dl-plym2m.dtb \
+	imx6dl-prtmvt.dtb \
 	imx6dl-prtrvt.dtb \
 	imx6dl-prtvt7.dtb \
 	imx6dl-rex-basic.dtb \
@ -481,6 +484,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-tx6u-811x.dtb \
 	imx6dl-tx6u-81xx-mb7.dtb \
 	imx6dl-udoo.dtb \
+	imx6dl-victgo.dtb \
+	imx6dl-vicut1.dtb \
 	imx6dl-wandboard.dtb \
 	imx6dl-wandboard-revb1.dtb \
 	imx6dl-wandboard-revd1.dtb \
@ -574,6 +579,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-udoo.dtb \
 	imx6q-utilite-pro.dtb \
 	imx6q-var-dt6customboard.dtb \
+	imx6q-vicut1.dtb \
 	imx6q-wandboard.dtb \
 	imx6q-wandboard-revb1.dtb \
 	imx6q-wandboard-revd1.dtb \
@ -588,6 +594,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6qp-tx6qp-8037-mb7.dtb \
 	imx6qp-tx6qp-8137.dtb \
 	imx6qp-tx6qp-8137-mb7.dtb \
+	imx6qp-vicutp.dtb \
 	imx6qp-wandboard-revd1.dtb \
 	imx6qp-zii-rdu2.dtb
 dtb-$(CONFIG_SOC_IMX6SL) += \
@ -625,6 +632,7 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-pico-pi.dtb \
 	imx6ul-phytec-segin-ff-rdk-emmc.dtb \
 	imx6ul-phytec-segin-ff-rdk-nand.dtb \
+	imx6ul-prti6g.dtb \
 	imx6ul-tx6ul-0010.dtb \
 	imx6ul-tx6ul-0011.dtb \
 	imx6ul-tx6ul-mainboard.dtb \
@ -811,6 +819,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-lxm.dtb \
 	am335x-moxa-uc-2101.dtb \
 	am335x-moxa-uc-8100-me-t.dtb \
+	am335x-myirtech-myd.dtb \
 	am335x-nano.dtb \
 	am335x-netcan-plus-1xx.dtb \
 	am335x-netcom-plus-2xx.dtb \
@ -901,6 +910,9 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-apq8074-dragonboard.dtb \
 	qcom-apq8084-ifc6540.dtb \
 	qcom-apq8084-mtp.dtb \
+	qcom-ipq4018-ap120c-ac.dtb \
+	qcom-ipq4018-ap120c-ac-bit.dtb \
+	qcom-ipq4018-jalapeno.dtb \
 	qcom-ipq4019-ap.dk01.1-c1.dtb \
 	qcom-ipq4019-ap.dk04.1-c1.dtb \
 	qcom-ipq4019-ap.dk04.1-c3.dtb \
@ -916,7 +928,8 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8974-sony-xperia-amami.dtb \
 	qcom-msm8974-sony-xperia-castor.dtb \
 	qcom-msm8974-sony-xperia-honami.dtb \
-	qcom-mdm9615-wp8548-mangoh-green.dtb
+	qcom-mdm9615-wp8548-mangoh-green.dtb \
+	qcom-sdx55-mtp.dtb
 dtb-$(CONFIG_ARCH_RDA) += \
 	rda8810pl-orangepi-2g-iot.dtb \
 	rda8810pl-orangepi-i96.dtb
@ -1213,6 +1226,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-s3-lichee-zero-plus.dtb \
 	sun8i-s3-pinecube.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
+	sun8i-v3-sl631-imx179.dtb \
 	sun8i-v3s-licheepi-zero.dtb \
 	sun8i-v3s-licheepi-zero-dock.dtb \
 	sun8i-v40-bananapi-m2-berry.dtb
@ -1263,6 +1277,7 @@ dtb-$(CONFIG_ARCH_U8500) += \
 	ste-hrefv60plus-tvk.dtb \
 	ste-href520-tvk.dtb \
 	ste-ux500-samsung-golden.dtb \
+	ste-ux500-samsung-janice.dtb \
 	ste-ux500-samsung-skomer.dtb
 dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld4-ref.dtb \
@ -1292,6 +1307,7 @@ dtb-$(CONFIG_ARCH_VT8500) += \
 	wm8850-w70v2.dtb
 dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-cc108.dtb \
+	zynq-ebaz4205.dtb \
 	zynq-microzed.dtb \
 	zynq-parallella.dtb \
 	zynq-zc702.dtb \
@ -1387,6 +1403,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2500-evb.dtb \
 	aspeed-ast2600-evb.dtb \
 	aspeed-bmc-amd-ethanolx.dtb \
+	aspeed-bmc-ampere-mtjade.dtb \
 	aspeed-bmc-arm-centriq2400-rep.dtb \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-bytedance-g220a.dtb \
@ -1399,6 +1416,7 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-facebook-wedge400.dtb \
 	aspeed-bmc-facebook-yamp.dtb \
 	aspeed-bmc-facebook-yosemitev2.dtb \
+	aspeed-bmc-ibm-everest.dtb \
 	aspeed-bmc-ibm-rainier.dtb \
 	aspeed-bmc-ibm-rainier-4u.dtb \
 	aspeed-bmc-intel-s2600wf.dtb \
@ -1418,4 +1436,5 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-opp-witherspoon.dtb \
 	aspeed-bmc-opp-zaius.dtb \
 	aspeed-bmc-portwell-neptune.dtb \
-	aspeed-bmc-quanta-q71l.dtb
+	aspeed-bmc-quanta-q71l.dtb \
+	aspeed-bmc-supermicro-x11spi.dtb
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@ -684,28 +684,31 @@
 	};
 };

-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	slaves = <1>;
 };

-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";

 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
 	};
 };

-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-id";
+	ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+	 status = "disabled";
 };

 &tscadc {
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@ -596,19 +596,17 @@
 	};
 };

-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
-	dual_emac = <1>;
 	status = "okay";
 };

-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";

 	ethphy0: ethernet-phy@0 {
 		reg = <0>;
@ -619,16 +617,16 @@
 	};
 };

-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };

-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rgmii-id";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };

 &mmc1 {
--- a/arch/arm/boot/dts/am335x-icev2.dts
+++ b/arch/arm/boot/dts/am335x-icev2.dts
@ -474,31 +474,29 @@
 	};
 };

-&cpsw_emac0 {
+&cpsw_port1 {
 	phy-handle = <&ethphy0>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <1>;
+	ti,dual-emac-pvid = <1>;
 };

-&cpsw_emac1 {
+&cpsw_port2 {
 	phy-handle = <&ethphy1>;
 	phy-mode = "rmii";
-	dual_emac_res_vlan = <2>;
+	ti,dual-emac-pvid = <2>;
 };

-&mac {
+&mac_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
 	status = "okay";
-	dual_emac;
 };

-&davinci_mdio {
+&davinci_mdio_sw {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&davinci_mdio_default>;
 	pinctrl-1 = <&davinci_mdio_sleep>;
-	status = "okay";
 	reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
 	reset-delay-us = <2>;   /* PHY datasheet states 1uS min */

--- a/arch/arm/boot/dts/am335x-myirtech-myc.dtsi
+++ b/arch/arm/boot/dts/am335x-myirtech-myc.dtsi
@ -0,0 +1,267 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* SPDX-FileCopyrightText: Alexander Shiyan, <shc_work@mail.ru> */
+
+/* Based on code by myc_c335x.dts, MYiRtech.com */
+/* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */
+
+/dts-v1/;
+
+#include "am33xx.dtsi"
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "MYIR MYC-AM335X";
+	compatible = "myir,myc-am335x", "ti,am33xx";
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vdd_core>;
+			voltage-tolerance = <2>;
+		};
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+
+	vdd_mod: vdd_mod_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-mod";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_core: vdd_core_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-core";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_mod>;
+	};
+
+	leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_mod_pins>;
+
+		led_mod: led_mod {
+			label = "module:user";
+			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+};
+
+&cpsw_emac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+};
+
+&davinci_mdio {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mdio_pins_default>;
+	pinctrl-1 = <&mdio_pins_sleep>;
+	status = "okay";
+
+	phy0: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&nand_pins_default>;
+	pinctrl-1 = <&nand_pins_sleep>;
+	ranges = <0 0 0x8000000 0x1000000>;
+	status = "okay";
+
+	nand0: nand@0,0 {
+		compatible = "ti,omap2-nand";
+		reg = <0 0 4>;
+		interrupt-parent = <&gpmc>;
+		interrupts = <0 IRQ_TYPE_NONE>, <1 IRQ_TYPE_NONE>;
+		nand-bus-width = <8>;
+		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <44>;
+		gpmc,cs-wr-off-ns = <44>;
+		gpmc,adv-on-ns = <6>;
+		gpmc,adv-rd-off-ns = <34>;
+		gpmc,adv-wr-off-ns = <44>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <40>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <54>;
+		gpmc,access-ns = <64>;
+		gpmc,rd-cycle-ns = <82>;
+		gpmc,wr-cycle-ns = <82>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		ti,elm-id = <&elm>;
+		ti,nand-ecc-opt = "bch8";
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default", "gpio", "sleep";
+	pinctrl-0 = <&i2c0_pins_default>;
+	pinctrl-1 = <&i2c0_pins_gpio>;
+	pinctrl-2 = <&i2c0_pins_sleep>;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+		vcc-supply = <&vdd_mod>;
+	};
+};
+
+&mac {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&eth_slave1_pins_default>;
+	pinctrl-1 = <&eth_slave1_pins_sleep>;
+	slaves = <1>;
+	status = "okay";
+};
+
+&rtc {
+	system-power-controller;
+};
+
+&am33xx_pinmux {
+	mdio_pins_default: pinmux_mdio_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLUP | SLEWCTRL_FAST, MUX_MODE0)	/* mdio_data */
+			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLUP, MUX_MODE0)			/* mdio_clk */
+		>;
+	};
+
+	mdio_pins_sleep: pinmux_mdio_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	eth_slave1_pins_default: pinmux_eth_slave1_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_tctl */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rctl */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td3 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td2 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_td0 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_tclk */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rclk */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd3 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd2 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii1_rd0 */
+		>;
+	};
+
+	eth_slave1_pins_sleep: pinmux_eth_slave1_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_DV, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_TX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_CLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	i2c0_pins_default: pinmux_i2c0_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE0)	/* I2C0_SDA */
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE0)	/* I2C0_SCL */
+		>;
+	};
+
+	i2c0_pins_gpio: pinmux_i2c0_pins_gpio {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT, MUX_MODE7)			/* gpio3[5] */
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT, MUX_MODE7)			/* gpio3[6] */
+		>;
+	};
+
+	i2c0_pins_sleep: pinmux_i2c0_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_I2C0_SCL, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	led_mod_pins: pinmux_led_mod_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKR, PIN_OUTPUT_PULLDOWN, MUX_MODE7)		/* gpio3[18] */
+		>;
+	};
+
+	nand_pins_default: pinmux_nand_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad4 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad5 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad6 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_ad7 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLUP, MUX_MODE0)		/* gpmc_wait0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLUP, MUX_MODE7)		/* gpio0[31] */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT, MUX_MODE0)			/* gpmc_csn0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_OUTPUT, MUX_MODE0)			/* gpmc_advn_ale */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_OUTPUT, MUX_MODE0)			/* gpmc_oen_ren */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_OUTPUT, MUX_MODE0)			/* gpmc_wen */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN0_CLE, PIN_OUTPUT, MUX_MODE0)			/* gpmc_be0n_cle */
+		>;
+	};
+
+	nand_pins_sleep: pinmux_nand_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD4, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD5, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD6, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD7, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WAIT0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WPN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_ADVN_ALE, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_OEN_REN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_WEN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN0_CLE, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+};
--- a/arch/arm/boot/dts/am335x-myirtech-myd.dts
+++ b/arch/arm/boot/dts/am335x-myirtech-myd.dts
@ -0,0 +1,536 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/* SPDX-FileCopyrightText: Alexander Shiyan, <shc_work@mail.ru> */
+/* Based on code by myd_c335x.dts, MYiRtech.com */
+/* Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/ */
+
+/dts-v1/;
+
+#include "am335x-myirtech-myc.dtsi"
+
+#include <dt-bindings/display/tda998x.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MYIR MYD-AM335X";
+	compatible = "myir,myd-am335x", "myir,myc-am335x", "ti,am33xx";
+
+	chosen {
+		stdout-path = &uart0;
+	};
+
+	clk12m: clk12m {
+		compatible = "fixed-clock";
+		clock-frequency = <12000000>;
+
+		#clock-cells = <0>;
+	};
+
+	gpio_buttons: gpio_buttons {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_buttons_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		button1: button@0 {
+			reg = <0>;
+			label = "button1";
+			linux,code = <BTN_1>;
+			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button2: button@1 {
+			reg = <1>;
+			label = "button2";
+			linux,code = <BTN_2>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sound: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&master_codec>;
+		simple-audio-card,frame-master = <&master_codec>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&mcasp0>;
+		};
+
+		master_codec: simple-audio-card,codec@1 {
+			sound-dai = <&sgtl5000>;
+		};
+
+		simple-audio-card,codec@2 {
+			sound-dai = <&tda9988>;
+		};
+	};
+
+	vdd_5v0: vdd_5v0_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3: vdd_3v3_reg {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd_5v0>;
+	};
+};
+
+&cpsw_emac1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+};
+
+&davinci_mdio {
+	phy1: ethernet-phy@6 {
+		reg = <6>;
+		eee-broken-1000t;
+	};
+};
+
+&dcan0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcan0_pins_default>;
+	pinctrl-1 = <&dcan0_pins_sleep>;
+	status = "okay";
+};
+
+&dcan1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcan1_pins_default>;
+	pinctrl-1 = <&dcan1_pins_sleep>;
+	status = "okay";
+};
+
+&ehrpwm0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&ehrpwm0_pins_default>;
+	pinctrl-1 = <&ehrpwm0_pins_sleep>;
+	status = "okay";
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "gpio", "sleep";
+	pinctrl-0 = <&i2c1_pins_default>;
+	pinctrl-1 = <&i2c1_pins_gpio>;
+	pinctrl-2 = <&i2c1_pins_sleep>;
+	clock-frequency = <400000>;
+	scl-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio0 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	sgtl5000: sgtl5000@a {
+		compatible = "fsl,sgtl5000";
+		reg =<0xa>;
+		clocks = <&clk12m>;
+		micbias-resistor-k-ohms = <4>;
+		micbias-voltage-m-volts = <2250>;
+		VDDA-supply = <&vdd_3v3>;
+		VDDIO-supply = <&vdd_3v3>;
+
+		#sound-dai-cells = <0>;
+	};
+
+	tda9988: tda9988@70 {
+		compatible = "nxp,tda998x";
+		reg =<0x70>;
+		audio-ports = <TDA998x_I2S 1>;
+
+		#sound-dai-cells = <0>;
+
+		ports {
+			port@0 {
+				hdmi_0: endpoint@0 {
+					remote-endpoint = <&lcdc_0>;
+				};
+			};
+		};
+	};
+};
+
+&lcdc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&lcdc_pins_default>;
+	pinctrl-1 = <&lcdc_pins_sleep>;
+	blue-and-red-wiring = "straight";
+	status = "okay";
+
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <&hdmi_0>;
+		};
+	};
+};
+
+&leds {
+	pinctrl-0 = <&led_mod_pins &leds_pins>;
+
+	led1: led1 {
+		label = "base:user1";
+		gpios = <&gpio0 27 GPIO_ACTIVE_LOW>;
+		color = <LED_COLOR_ID_GREEN>;
+		default-state = "off";
+	};
+
+	led2: led2 {
+		label = "base:user2";
+		gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
+		color = <LED_COLOR_ID_GREEN>;
+		default-state = "off";
+	};
+};
+
+&mac {
+	pinctrl-0 = <&eth_slave1_pins_default>, <&eth_slave2_pins_default>;
+	pinctrl-1 = <&eth_slave1_pins_sleep>, <&eth_slave2_pins_sleep>;
+	slaves = <2>;
+};
+
+&mcasp0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mcasp0_pins_default>;
+	pinctrl-1 = <&mcasp0_pins_sleep>;
+	op-mode = <0>;
+	tdm-slots = <2>;
+	serial-dir = <0 1 2 0>;
+	tx-num-evt = <32>;
+	rx-num-evt = <32>;
+	status = "okay";
+
+	#sound-dai-cells = <0>;
+};
+
+&mmc1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mmc1_pins_default>;
+	pinctrl-1 = <&mmc1_pins_sleep>;
+	cd-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_3v3>;
+	status = "okay";
+};
+
+&nand0 {
+	partition@0 {
+		label = "MLO";
+		reg = <0x00000 0x20000>;
+	};
+
+	partition@20000 {
+		label = "boot";
+		reg = <0x20000 0x80000>;
+	};
+};
+
+&tscadc {
+	status = "okay";
+
+	adc: adc {
+		ti,adc-channels = <0 1 2 3 4 5 6>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&uart1_pins_default>;
+	pinctrl-1 = <&uart1_pins_sleep>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&uart2_pins_default>;
+	pinctrl-1 = <&uart2_pins_sleep>;
+	status = "okay";
+};
+
+&usb {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb_pins>;
+};
+
+&usb0 {
+	dr_mode = "otg";
+};
+
+&usb0_phy {
+	vcc-supply = <&vdd_5v0>;
+};
+
+&usb1 {
+	dr_mode = "host";
+};
+
+&usb1_phy {
+	vcc-supply = <&vdd_5v0>;
+};
+
+&vdd_mod {
+	vin-supply = <&vdd_3v3>;
+};
+
+&am33xx_pinmux {
+	dcan0_pins_default: pinmux_dcan0_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_OUTPUT, MUX_MODE2)			/* dcan0_tx_mux2 */
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT, MUX_MODE2)			/* dcan0_rx_mux2 */
+		>;
+	};
+
+	dcan0_pins_sleep: pinmux_dcan0_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	dcan1_pins_default: pinmux_dcan1_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_OUTPUT, MUX_MODE2)			/* dcan1_tx_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT, MUX_MODE2)			/* dcan1_rx_mux0 */
+		>;
+	};
+
+	dcan1_pins_sleep: pinmux_dcan1_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_UART0_RTSN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	ehrpwm0_pins_default: pinmux_ehrpwm0_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_OUTPUT, MUX_MODE3)			/* ehrpwm0A_mux1 */
+		>;
+	};
+
+	ehrpwm0_pins_sleep: pinmux_ehrpwm0_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_SCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	eth_slave2_pins_default: pinmux_eth_slave2_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_tctl */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rctl */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_td0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_OUTPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_tclk */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rclk */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rd3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* rgmii2_rd2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE2		/* rgmii2_rd1 */)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE2		/* rgmii2_rd0 */)
+		>;
+	};
+
+	eth_slave2_pins_sleep: pinmux_eth_slave2_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A2, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A3, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A4, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A5, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A6, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A7, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A8, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A10, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A11, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	gpio_buttons_pins: pinmux_gpio_buttons_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_COL, PIN_INPUT_PULLDOWN, MUX_MODE7)		/* gpio3[0] */
+			AM33XX_PADCONF(AM335X_PIN_RMII1_REF_CLK, PIN_INPUT, MUX_MODE7)			/* gpio0[29] */
+		>;
+	};
+
+	i2c1_pins_default: pinmux_i2c1_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE2)	/* I2C1_SDA_mux3 */
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT | SLEWCTRL_FAST, MUX_MODE2)	/* I2C1_SCL_mux3 */
+		>;
+	};
+
+	i2c1_pins_gpio: pinmux_i2c1_pins_gpio {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT, MUX_MODE7)			/* gpio0[4] */
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT, MUX_MODE7)			/* gpio0[5] */
+		>;
+	};
+
+	i2c1_pins_sleep: pinmux_i2c1_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_SPI0_CS0, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	lcdc_pins_default: pinmux_lcdc_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PIN_OUTPUT, MUX_MODE0)			/* lcd_data0 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PIN_OUTPUT, MUX_MODE0)			/* lcd_data1 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PIN_OUTPUT, MUX_MODE0)			/* lcd_data2 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PIN_OUTPUT, MUX_MODE0)			/* lcd_data3 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PIN_OUTPUT, MUX_MODE0)			/* lcd_data4 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PIN_OUTPUT, MUX_MODE0)			/* lcd_data5 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PIN_OUTPUT, MUX_MODE0)			/* lcd_data6 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PIN_OUTPUT, MUX_MODE0)			/* lcd_data7 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PIN_OUTPUT, MUX_MODE0)			/* lcd_data8 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PIN_OUTPUT, MUX_MODE0)			/* lcd_data9 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PIN_OUTPUT, MUX_MODE0)			/* lcd_data10 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PIN_OUTPUT, MUX_MODE0)			/* lcd_data11 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PIN_OUTPUT, MUX_MODE0)			/* lcd_data12 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PIN_OUTPUT, MUX_MODE0)			/* lcd_data13 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PIN_OUTPUT, MUX_MODE0)			/* lcd_data14 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PIN_OUTPUT, MUX_MODE0)			/* lcd_data15 */
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_OUTPUT, MUX_MODE0)			/* lcd_vsync */
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_OUTPUT, MUX_MODE0)			/* lcd_hsync */
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_OUTPUT, MUX_MODE0)			/* lcd_pclk */
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_OUTPUT, MUX_MODE0)		/* lcd_ac_bias_en */
+		>;
+	};
+
+	lcdc_pins_sleep: pinmux_lcdc_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA0, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA1, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA2, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA3, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA4, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA5, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA6, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA7, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA8, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA9, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA10, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA11, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA12, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA13, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA14, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_DATA15, PULL_DISABLE, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_VSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_HSYNC, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_PCLK, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_LCD_AC_BIAS_EN, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	leds_pins: pinmux_leds_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_OUTPUT, MUX_MODE7)			/* gpio0[27] */
+			AM33XX_PADCONF(AM335X_PIN_SPI0_D0, PIN_OUTPUT, MUX_MODE7)			/* gpio0[3] */
+		>;
+	};
+
+	mcasp0_pins_default: pinmux_mcasp0_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE0)		/* mcasp0_aclkx_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE0)		/* mcasp0_fsx_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT_PULLDOWN, MUX_MODE2)		/* mcasp0_axr2_mux0 */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_INPUT_PULLDOWN, MUX_MODE0)		/* mcasp0_axr1_mux0 */
+		>;
+	};
+
+	mcasp0_pins_sleep: pinmux_mcasp0_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_ACLKX, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_FSX, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKR, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AXR1, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	mmc1_pins_default: pinmux_mmc1_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat3 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat2 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat1 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_dat0 */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_clk */
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLUP, MUX_MODE0)		/* mmc0_cmd */
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLUP, MUX_MODE7)		/* gpio3[21] */
+		>;
+	};
+
+	mmc1_pins_sleep: pinmux_mmc1_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT3, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT2, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT1, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_DAT0, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CLK, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MMC0_CMD, PIN_INPUT_PULLDOWN, MUX_MODE0)
+			AM33XX_PADCONF(AM335X_PIN_MCASP0_AHCLKX, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	uart0_pins: pinmux_uart0_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART0_RXD, PIN_INPUT_PULLUP, MUX_MODE0)		/* uart0_rxd */
+			AM33XX_PADCONF(AM335X_PIN_UART0_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* uart0_txd */
+		>;
+	};
+
+	uart1_pins_default: pinmux_uart1_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLUP, MUX_MODE0)		/* uart1_rxd */
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* uart1_txd */
+		>;
+	};
+
+	uart1_pins_sleep: pinmux_uart1_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	uart2_pins_default: pinmux_uart2_pins_default {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT, MUX_MODE6)			/* uart2_rxd_mux1 */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_OUTPUT, MUX_MODE6)			/* uart2_txd_mux1 */
+		>;
+	};
+
+	uart2_pins_sleep: pinmux_uart2_pins_sleep {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_CRS, PIN_INPUT_PULLDOWN, MUX_MODE7)
+			AM33XX_PADCONF(AM335X_PIN_MII1_RX_ER, PIN_INPUT_PULLDOWN, MUX_MODE7)
+		>;
+	};
+
+	usb_pins: pinmux_usb_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_USB0_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* USB0_DRVVBUS */
+			AM33XX_PADCONF(AM335X_PIN_USB1_DRVVBUS, PIN_OUTPUT_PULLDOWN, MUX_MODE0)		/* USB1_DRVVBUS */
+		>;
+	};
+};
--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/am33xx-l4.dtsi
@ -765,6 +765,55 @@
 					phys = <&phy_gmii_sel 2 1>;
 				};
 			};
+
+			mac_sw: switch@0 {
+				compatible = "ti,am335x-cpsw-switch", "ti,cpsw-switch";
+				reg = <0x0 0x4000>;
+				ranges = <0 0 0x4000>;
+				clocks = <&cpsw_125mhz_gclk>;
+				clock-names = "fck";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				syscon = <&scm_conf>;
+				status = "disabled";
+
+				interrupts = <40 41 42 43>;
+				interrupt-names = "rx_thresh", "rx", "tx", "misc";
+
+				ethernet-ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					cpsw_port1: port@1 {
+						reg = <1>;
+						label = "port1";
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 1 1>;
+					};
+
+					cpsw_port2: port@2 {
+						reg = <2>;
+						label = "port2";
+						mac-address = [ 00 00 00 00 00 00 ];
+						phys = <&phy_gmii_sel 2 1>;
+					};
+				};
+
+				davinci_mdio_sw: mdio@1000 {
+					compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+					clocks = <&cpsw_125mhz_gclk>;
+					clock-names = "fck";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					bus_freq = <1000000>;
+					reg = <0x1000 0x100>;
+				};
+
+				cpts {
+					clocks = <&cpsw_cpts_rft_clk>;
+					clock-names = "cpts";
+				};
+			};
 		};

 		target-module@180000 {			/* 0x4a180000, ap 5 10.0 */
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/am574x-idk.dts
@ -39,3 +39,7 @@
 &m_can0 {
 	status = "disabled";
 };
+
+&emif1 {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
@ -148,6 +148,8 @@
 		reg = <0>;
 		label = "pxa3xx_nand-0";
 		nand-rb = <0>;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
 		marvell,nand-keep-config;
 		nand-on-flash-bbt;
 	};
--- a/arch/arm/boot/dts/armada-388-helios4.dts
+++ b/arch/arm/boot/dts/armada-388-helios4.dts
@ -70,6 +70,9 @@

 	system-leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_system_led_pins>;
+
 		status-led {
 			label = "helios4:green:status";
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
@ -86,6 +89,9 @@

 	io-leds {
 		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_io_led_pins>;
+
 		sata1-led {
 			label = "helios4:green:ata1";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
@ -121,11 +127,15 @@
 	fan1: j10-pwm {
 		compatible = "pwm-fan";
 		pwms = <&gpio1 9 40000>;	/* Target freq:25 kHz */
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_fan1_pins>;
 	};

 	fan2: j17-pwm {
 		compatible = "pwm-fan";
 		pwms = <&gpio1 23 40000>;	/* Target freq:25 kHz */
+		pinctrl-names = "default";
+		pinctrl-0 = <&helios_fan2_pins>;
 	};

 	usb2_phy: usb2-phy {
@ -286,16 +296,22 @@
 						       "mpp39", "mpp40";
 					marvell,function = "sd0";
 				};
-				helios_led_pins: helios-led-pins {
-					marvell,pins = "mpp24", "mpp25",
-						       "mpp49", "mpp50",
+				helios_system_led_pins: helios-system-led-pins {
+					marvell,pins = "mpp24", "mpp25";
+					marvell,function = "gpio";
+				};
+				helios_io_led_pins: helios-io-led-pins {
+					marvell,pins = "mpp49", "mpp50",
 						       "mpp52", "mpp53",
 						       "mpp54";
 					marvell,function = "gpio";
 				};
-				helios_fan_pins: helios-fan-pins {
-					marvell,pins = "mpp41", "mpp43",
-						       "mpp48", "mpp55";
+				helios_fan1_pins: helios_fan1_pins {
+					marvell,pins = "mpp41", "mpp43";
+					marvell,function = "gpio";
+				};
+				helios_fan2_pins: helios_fan2_pins {
+					marvell,pins = "mpp48", "mpp55";
 					marvell,function = "gpio";
 				};
 				microsom_spi1_cs_pins: spi1-cs-pins {
--- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
+++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
@ -237,3 +237,11 @@
 &fsim0 {
 	status = "okay";
 };
+
+&ehci1 {
+	status = "okay";
+};
+
+&uhci {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-amd-ethanolx.dts
@ -218,7 +218,7 @@

 &lpc_snoop {
 	status = "okay";
-	snoop-ports = <0x80>;
+	snoop-ports = <0x80>, <0x81>;
 };

 &lpc_ctrl {
--- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
@ -0,0 +1,558 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt. Jade BMC";
+	compatible = "ampere,mtjade-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlyprintk";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		fault {
+			gpios = <&gpio ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>;
+		};
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(Q, 6) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		shutdown_ack {
+			label = "SHUTDOWN_ACK";
+			gpios = <&gpio ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(G, 2)>;
+		};
+
+		reboot_ack {
+			label = "REBOOT_ACK";
+			gpios = <&gpio ASPEED_GPIO(J, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(J, 3)>;
+		};
+
+		S0_overtemp {
+			label = "S0_OVERTEMP";
+			gpios = <&gpio ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(G, 3)>;
+		};
+
+		S0_hightemp {
+			label = "S0_HIGHTEMP";
+			gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(J, 0)>;
+		};
+
+		S0_cpu_fault {
+			label = "S0_CPU_FAULT";
+			gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(J, 1)>;
+		};
+
+		S1_overtemp {
+			label = "S1_OVERTEMP";
+			gpios = <&gpio ASPEED_GPIO(Z, 6) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(Z, 6)>;
+		};
+
+		S1_hightemp {
+			label = "S1_HIGHTEMP";
+			gpios = <&gpio ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(AB, 0)>;
+		};
+
+		S1_cpu_fault {
+			label = "S1_CPU_FAULT";
+			gpios = <&gpio ASPEED_GPIO(Z, 1) GPIO_ACTIVE_HIGH>;
+			linux,code = <ASPEED_GPIO(Z, 1)>;
+		};
+
+		id_button {
+			label = "ID_BUTTON";
+			gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <ASPEED_GPIO(Q, 5)>;
+		};
+
+	};
+
+	gpioA0mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio ASPEED_GPIO(A, 0) GPIO_ACTIVE_LOW>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 8>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 9>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 10>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 11>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 12>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc 13>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioA0mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>;
+	};
+
+	iio-hwmon-adc14 {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 14>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		/* spi-max-frequency = <50000000>; */
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		/* spi-max-frequency = <100000000>; */
+	};
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			 &pinctrl_rxd1_default
+			 &pinctrl_ncts1_default
+			 &pinctrl_nrts1_default>;
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			 &pinctrl_rxd2_default>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd3_default
+			 &pinctrl_rxd3_default>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd4_default
+			 &pinctrl_rxd4_default>;
+};
+
+/* The BMC's uart */
+&uart5 {
+	status = "okay";
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "microchip,24c64", "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	inlet_mem2: tmp175@28 {
+		compatible = "ti,tmp175";
+		reg = <0x28>;
+	};
+
+	inlet_cpu: tmp175@29 {
+		compatible = "ti,tmp175";
+		reg = <0x29>;
+	};
+
+	inlet_mem1: tmp175@2a {
+		compatible = "ti,tmp175";
+		reg = <0x2a>;
+	};
+
+	outlet_cpu: tmp175@2b {
+		compatible = "ti,tmp175";
+		reg = <0x2b>;
+	};
+
+	outlet1: tmp175@2c {
+		compatible = "ti,tmp175";
+		reg = <0x2c>;
+	};
+
+	outlet2: tmp175@2d {
+		compatible = "ti,tmp175";
+		reg = <0x2d>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2_default &pinctrl_pwm3_default
+			&pinctrl_pwm4_default &pinctrl_pwm5_default
+			&pinctrl_pwm6_default &pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@1 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	fan@2 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+	};
+
+	fan@5 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+	};
+
+	fan@6 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+	};
+
+	fan@7 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+	};
+
+	fan@8 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+	};
+
+	fan@9 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+	};
+
+	fan@10 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
+	};
+
+	fan@11 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
+	};
+
+};
+
+&vhub {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","","","S0_BMC_SPECIAL_BOOT","","","","",
+	/*B0-B7*/	"BMC_SELECT_EEPROM","","","",
+			"POWER_BUTTON","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","BMC_SYS_PSON_L","S0_DDR_SAVE","PGOOD",
+			"S1_DDR_SAVE","","",
+	/*G0-G7*/	"S0_FW_BOOT_OK","SHD_REQ_L","","S0_OVERTEMP_L","","",
+			"","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","S1_BMC_SPECIAL_BOOT","","","","","",
+	/*J0-J7*/	"S0_HIGHTEMP_L","S0_FAULT_L","S0_SCP_AUTH_FAIL_L","",
+			"","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/       "","","","BMC_SYSRESET_L","SPI_AUTH_FAIL_L","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","UID_BUTTON","","",
+	/*R0-R7*/	"","","BMC_EXT_HIGHTEMP_L","","","RESET_BUTTON","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"S0_BMC_PLIMIT","S1_FAULT_L","S1_FW_BOOT_OK","","",
+			"S1_SCP_AUTH_FAIL_L","S1_OVERTEMP_L","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"S1_HIGHTEMP_L","S1_BMC_PLIMIT","S0_BMC_DDR_ADDR",
+			"S1_BMC_DDR_ADR","","","","",
+	/*AC0-AC7*/	"SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L",
+			"BMC_OCP_PG";
+};
--- a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts
@ -446,7 +446,11 @@

 &i2c4 {
 	status = "okay";
-
+	ipmb0@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
 };

 &i2c5 {
@ -901,14 +905,14 @@
 &gpio {
 	pin_gpio_i3 {
 		gpio-hog;
-		gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_LOW>;
+		gpios = <ASPEED_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "NCSI_BMC_R_SEL";
 	};

 	pin_gpio_b6 {
 		gpio-hog;
-		gpios = <ASPEED_GPIO(B, 6) GPIO_ACTIVE_LOW>;
+		gpios = <ASPEED_GPIO(B, 6) GPIO_ACTIVE_HIGH>;
 		output-low;
 		line-name = "EN_NCSI_SWITCH_N";
 	};
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
@ -0,0 +1,775 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2020 IBM Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+
+/ {
+	model = "Everest";
+	compatible = "ibm,everest-bmc", "aspeed,ast2600";
+
+	aliases {
+		i2c100 = &cfam0_i2c0;
+		i2c101 = &cfam0_i2c1;
+		i2c110 = &cfam0_i2c10;
+		i2c111 = &cfam0_i2c11;
+		i2c112 = &cfam0_i2c12;
+		i2c113 = &cfam0_i2c13;
+		i2c114 = &cfam0_i2c14;
+		i2c115 = &cfam0_i2c15;
+		i2c202 = &cfam1_i2c2;
+		i2c203 = &cfam1_i2c3;
+		i2c210 = &cfam1_i2c10;
+		i2c211 = &cfam1_i2c11;
+		i2c214 = &cfam1_i2c14;
+		i2c215 = &cfam1_i2c15;
+		i2c216 = &cfam1_i2c16;
+		i2c217 = &cfam1_i2c17;
+		i2c300 = &cfam2_i2c0;
+		i2c301 = &cfam2_i2c1;
+		i2c310 = &cfam2_i2c10;
+		i2c311 = &cfam2_i2c11;
+		i2c312 = &cfam2_i2c12;
+		i2c313 = &cfam2_i2c13;
+		i2c314 = &cfam2_i2c14;
+		i2c315 = &cfam2_i2c15;
+		i2c402 = &cfam3_i2c2;
+		i2c403 = &cfam3_i2c3;
+		i2c410 = &cfam3_i2c10;
+		i2c411 = &cfam3_i2c11;
+		i2c414 = &cfam3_i2c14;
+		i2c415 = &cfam3_i2c15;
+		i2c416 = &cfam3_i2c16;
+		i2c417 = &cfam3_i2c17;
+
+		serial4 = &uart5;
+
+		spi10 = &cfam0_spi0;
+		spi11 = &cfam0_spi1;
+		spi12 = &cfam0_spi2;
+		spi13 = &cfam0_spi3;
+		spi20 = &cfam1_spi0;
+		spi21 = &cfam1_spi1;
+		spi22 = &cfam1_spi2;
+		spi23 = &cfam1_spi3;
+		spi30 = &cfam2_spi0;
+		spi31 = &cfam2_spi1;
+		spi32 = &cfam2_spi2;
+		spi33 = &cfam2_spi3;
+		spi40 = &cfam3_spi0;
+		spi41 = &cfam3_spi1;
+		spi42 = &cfam3_spi2;
+		spi43 = &cfam3_spi3;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		/* LPC FW cycle bridge region requires natural alignment */
+		flash_memory: region@b8000000 {
+			no-map;
+			reg = <0xb8000000 0x04000000>; /* 64M */
+		};
+
+		/* 48MB region from the end of flash to start of vga memory */
+		ramoops@bc000000 {
+			compatible = "ramoops";
+			reg = <0xbc000000 0x180000>; /* 16 * (3 * 0x8000) */
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			pmsg-size = <0x8000>;
+			max-reason = <3>; /* KMSG_DUMP_EMERG */
+		};
+
+		/* VGA region is dictated by hardware strapping */
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>; /* 16M */
+		};
+	};
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&pinctrl_emmc_default {
+	bias-disable;
+};
+
+&emmc {
+	status = "okay";
+};
+
+&fsim0 {
+	status = "okay";
+
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	/*
+	 * CFAM Reset is supposed to be active low but pass1 hardware is wired
+	 * active high.
+	 */
+	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_HIGH>;
+
+	cfam@0,0 {
+		reg = <0 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <0>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OMI01 */
+			};
+
+			cfam0_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OMI23 */
+			};
+
+			cfam0_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam0_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam0_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam0_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam0_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam0_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam0_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam0_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ0: occ {
+				compatible = "ibm,p10-occ";
+			};
+		};
+
+		fsi_hub0: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+	};
+};
+
+&fsi_hub0 {
+	cfam@1,0 {
+		reg = <1 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <1>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OMI45 */
+			};
+
+			cfam1_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OMI67 */
+			};
+
+			cfam1_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam1_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam1_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam1_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam1_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam1_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam1_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam1_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ1: occ {
+				compatible = "ibm,p10-occ";
+			};
+		};
+
+		fsi_hub1: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@2,0 {
+		reg = <2 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <2>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_i2c0: i2c-bus@0 {
+				reg = <0>;	/* OM01 */
+			};
+
+			cfam2_i2c1: i2c-bus@1 {
+				reg = <1>;	/* OM23 */
+			};
+
+			cfam2_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam2_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam2_i2c12: i2c-bus@c {
+				reg = <12>;	/* OP4A */
+			};
+
+			cfam2_i2c13: i2c-bus@d {
+				reg = <13>;	/* OP4B */
+			};
+
+			cfam2_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam2_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam2_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam2_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ2: occ {
+				compatible = "ibm,p10-occ";
+			};
+		};
+
+		fsi_hub2: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+
+	cfam@3,0 {
+		reg = <3 0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		chip-id = <3>;
+
+		scom@1000 {
+			compatible = "ibm,fsi2pib";
+			reg = <0x1000 0x400>;
+		};
+
+		i2c@1800 {
+			compatible = "ibm,fsi-i2c-master";
+			reg = <0x1800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_i2c2: i2c-bus@2 {
+				reg = <2>;	/* OM45 */
+			};
+
+			cfam3_i2c3: i2c-bus@3 {
+				reg = <3>;	/* OM67 */
+			};
+
+			cfam3_i2c10: i2c-bus@a {
+				reg = <10>;	/* OP3A */
+			};
+
+			cfam3_i2c11: i2c-bus@b {
+				reg = <11>;	/* OP3B */
+			};
+
+			cfam3_i2c14: i2c-bus@e {
+				reg = <14>;	/* OP5A */
+			};
+
+			cfam3_i2c15: i2c-bus@f {
+				reg = <15>;	/* OP5B */
+			};
+
+			cfam3_i2c16: i2c-bus@10 {
+				reg = <16>;	/* OP6A */
+			};
+
+			cfam3_i2c17: i2c-bus@11 {
+				reg = <17>;	/* OP6B */
+			};
+		};
+
+		fsi2spi@1c00 {
+			compatible = "ibm,fsi2spi";
+			reg = <0x1c00 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cfam3_spi0: spi@0 {
+				reg = <0x0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi1: spi@20 {
+				reg = <0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi2: spi@40 {
+				reg = <0x40>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+
+			cfam3_spi3: spi@60 {
+				reg = <0x60>;
+				compatible = "ibm,fsi2spi-restricted";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eeprom@0 {
+					at25,byte-len = <0x80000>;
+					at25,addr-mode = <4>;
+					at25,page-size = <256>;
+
+					compatible = "atmel,at25";
+					reg = <0>;
+					spi-max-frequency = <1000000>;
+				};
+			};
+		};
+
+		sbefifo@2400 {
+			compatible = "ibm,p9-sbefifo";
+			reg = <0x2400 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			fsi_occ3: occ {
+				compatible = "ibm,p10-occ";
+			};
+		};
+
+		fsi_hub3: hub@3400 {
+			compatible = "fsi-master-hub";
+			reg = <0x3400 0x400>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			no-scan-on-init;
+		};
+	};
+};
+
+/* Legacy OCC numbering (to get rid of when userspace is fixed) */
+&fsi_occ0 {
+	reg = <1>;
+};
+
+&fsi_occ1 {
+	reg = <2>;
+};
+
+&fsi_occ2 {
+	reg = <3>;
+};
+
+&fsi_occ3 {
+	reg = <4>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&vuart1 {
+	status = "okay";
+};
+
+&vuart2 {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+	memory-region = <&flash_memory>;
+};
+
+&kcs4 {
+	compatible = "openbmc,mctp-lpc";
+	status = "okay";
+};
+
+&mac2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii3_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>,
+		 <&syscon ASPEED_CLK_MAC3RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&mac3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+	clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>,
+		 <&syscon ASPEED_CLK_MAC4RCLK>;
+	clock-names = "MACCLK", "RCLK";
+	use-ncsi;
+};
+
+&xdma {
+	status = "okay";
+	memory-region = <&vga_memory>;
+};
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@ -195,6 +195,7 @@

 &emmc {
 	status = "okay";
+	clk-phase-mmc-hs200 = <180>, <180>;
 };

 &fsim0 {
@ -579,7 +580,7 @@
 		gpio-controller;
 		#gpio-cells = <2>;

-		smbus0 {
+		smbus0-hog {
 			gpio-hog;
 			gpios = <4 GPIO_ACTIVE_HIGH>;
 			output-high;
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
@ -204,6 +204,39 @@

 };

+&gpio {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"","","front-psu","checkstop","cfam-reset","","","init-ok",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"ps0-presence","ps1-presence","","","front-memory","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","front-fan","","","",
+	/*I0-I7*/	"front-syshealth","front-syshot","mux-gpios","enable-gpios","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","power","trans-gpios","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","identify",
+	/*AA0-AA7*/	"clock-gpios","","data-gpios","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
 &fmc {
 	status = "okay";

@ -756,12 +789,12 @@
 	status = "okay";

 	power-supply@58 {
-		compatible = "pmbus";
+		compatible = "inspur,ipsps1";
 		reg = <0x58>;
 	};

 	power-supply@59 {
-		compatible = "pmbus";
+		compatible = "inspur,ipsps1";
 		reg = <0x59>;
 	};
 };
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
@ -827,7 +827,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus0 {
+				smbus0-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -852,7 +852,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus1 {
+				smbus1-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -900,7 +900,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus2 {
+				smbus2-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -925,7 +925,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus3 {
+				smbus3-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -992,7 +992,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus4 {
+				smbus4-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -1017,7 +1017,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus5 {
+				smbus5-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -1065,7 +1065,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus6 {
+				smbus6-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
@ -1090,7 +1090,7 @@
 				gpio-controller;
 				#gpio-cells = <2>;

-				smbus7 {
+				smbus7-hog {
 					gpio-hog;
 					gpios = <4 GPIO_ACTIVE_HIGH>;
 					output-high;
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
@ -582,6 +582,11 @@
 	/* TMP275A */
 	/* TMP275A */

+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+
 	tmp275@48 {
 		compatible = "ti,tmp275";
 		reg = <0x48>;
--- a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
@ -121,6 +121,8 @@
 	pca9555@27 {
 		compatible = "nxp,pca9555";
 		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
 	};
 };

--- a/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-supermicro-x11spi.dts
@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2020 Super Micro Computer, Inc
+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+
+/ {
+	model = "X11SPI BMC";
+	compatible = "supermicro,x11spi-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "earlyprintk";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		vga_memory: framebuffer@7f000000 {
+			no-map;
+			reg = <0x7f000000 0x01000000>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+
+};
+
+&gpio {
+    status = "okay";
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&mac0 {
+    status = "okay";
+
+    pinctrl-names = "default";
+    pinctrl-0 = <&pinctrl_rmii1_default>;
+    clocks = <&syscon ASPEED_CLK_GATE_MAC1CLK>,
+           <&syscon ASPEED_CLK_MAC1RCLK>;
+    clock-names = "MACCLK", "RCLK";
+    use-ncsi;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&gfx {
+	status = "okay";
+};
+
+&pinctrl {
+	aspeed,external-nodes = <&gfx &lhc>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default
+			 &pinctrl_pwm6_default &pinctrl_pwm7_default>;
+};
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed-g4.dtsi
@ -375,6 +375,7 @@
 						compatible = "aspeed,ast2400-lpc-snoop";
 						reg = <0x10 0x8>;
 						interrupts = <8>;
+						clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 						status = "disabled";
 					};

--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@ -497,6 +497,7 @@
 						compatible = "aspeed,ast2500-lpc-snoop";
 						reg = <0x10 0x8>;
 						interrupts = <8>;
+						clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 						status = "disabled";
 					};

--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@ -524,6 +524,7 @@
 						compatible = "aspeed,ast2600-lpc-snoop";
 						reg = <0x0 0x80>;
 						interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+						clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 						status = "disabled";
 					};

--- a/arch/arm/boot/dts/at91-kizbox3_common.dtsi
+++ b/arch/arm/boot/dts/at91-kizbox3_common.dtsi
@ -341,7 +341,6 @@

 	input@0 {
 		reg = <0>;
-		atmel,wakeup-type = "low";
 	};
 };

--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@ -142,7 +142,6 @@

 				input@0 {
 					reg = <0>;
-					atmel,wakeup-type = "low";
 				};
 			};

--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
@ -43,14 +43,20 @@

 &i2c0 {
 	pinctrl-0 = <&pinctrl_i2c0_default>;
-	pinctrl-names = "default";
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	pinctrl-names = "default", "gpio";
+	sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };

 &i2c1 {
 	dmas = <0>, <0>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";

 	mcp16502@5b {
@ -258,12 +264,24 @@
 		bias-disable;
 	};

+	pinctrl_i2c0_gpio: i2c0_gpio {
+		pinmux = <PIN_PD21__GPIO>,
+			 <PIN_PD22__GPIO>;
+		bias-disable;
+	};
+
 	pinctrl_i2c1_default: i2c1_default {
 		pinmux = <PIN_PD19__TWD1>,
 			 <PIN_PD20__TWCK1>;
 		bias-disable;
 	};

+	pinctrl_i2c1_gpio: i2c1_gpio {
+		pinmux = <PIN_PD19__GPIO>,
+			 <PIN_PD20__GPIO>;
+		bias-disable;
+	};
+
 	pinctrl_macb0_default: macb0_default {
 		pinmux = <PIN_PB14__GTXCK>,
 			 <PIN_PB15__GTXEN>,
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
@ -209,7 +209,6 @@

 	input@0 {
 		reg = <0>;
-		atmel,wakeup-type = "low";
 	};
 };

--- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts
@ -697,7 +697,6 @@

 	input@0 {
 		reg = <0>;
-		atmel,wakeup-type = "low";
 	};
 };

--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@ -206,7 +206,6 @@

 				input@0 {
 					reg = <0>;
-					atmel,wakeup-type = "low";
 				};
 			};

--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@ -351,7 +351,6 @@

 				input@0 {
 					reg = <0>;
-					atmel,wakeup-type = "low";
 				};
 			};

--- a/arch/arm/boot/dts/bcm21664.dtsi
+++ b/arch/arm/boot/dts/bcm21664.dtsi
@ -27,7 +27,7 @@
 		bootargs = "console=ttyS0,115200n8";
 	};

-       cpus {
+	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;

--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@ -25,6 +25,7 @@
 		emmc2bus = &emmc2bus;
 		ethernet0 = &genet;
 		pcie0 = &pcie0;
+		blconfig = &blconfig;
 	};

 	leds {
@ -218,6 +219,22 @@
 	status = "okay";
 };

+&rmem {
+	/*
+	 * RPi4's co-processor will copy the board's bootloader configuration
+	 * into memory for the OS to consume. It'll also update this node with
+	 * its placement information.
+	 */
+	blconfig: nvram@0 {
+		compatible = "raspberrypi,bootloader-config", "nvmem-rmem";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x0 0x0 0x0>;
+		no-map;
+		status = "disabled";
+	};
+};
+
 /* SDHCI is used to control the SDIO for wireless */
 &sdhci {
 	#address-cells = <1>;
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@ -308,6 +308,22 @@
 			#reset-cells = <1>;
 		};

+		bsc_intr: interrupt-controller@7ef00040 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7ef00040 0x30>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		aon_intr: interrupt-controller@7ef00100 {
+			compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
+			reg = <0x7ef00100 0x30>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
 		hdmi0: hdmi@7ef00700 {
 			compatible = "brcm,bcm2711-hdmi0";
 			reg = <0x7ef00700 0x300>,
@ -330,6 +346,11 @@
 				    "hd";
 			clock-names = "hdmi", "bvb", "audio", "cec";
 			resets = <&dvp 0>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <0>, <1>, <2>,
+				     <3>, <4>, <5>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
 			ddc = <&ddc0>;
 			dmas = <&dma 10>;
 			dma-names = "audio-rx";
@ -341,6 +362,8 @@
 			reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>;
 			reg-names = "bsc", "auto-i2c";
 			clock-frequency = <97500>;
+			interrupt-parent = <&bsc_intr>;
+			interrupts = <0>;
 			status = "disabled";
 		};

@ -367,6 +390,11 @@
 			ddc = <&ddc1>;
 			clock-names = "hdmi", "bvb", "audio", "cec";
 			resets = <&dvp 1>;
+			interrupt-parent = <&aon_intr>;
+			interrupts = <8>, <7>, <6>,
+				     <9>, <10>, <11>;
+			interrupt-names = "cec-tx", "cec-rx", "cec-low",
+					  "wakeup", "hpd-connected", "hpd-removed";
 			dmas = <&dma 17>;
 			dma-names = "audio-rx";
 			status = "disabled";
@ -377,6 +405,8 @@
 			reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>;
 			reg-names = "bsc", "auto-i2c";
 			clock-frequency = <97500>;
+			interrupt-parent = <&bsc_intr>;
+			interrupts = <1>;
 			status = "disabled";
 		};
 	};
@ -540,6 +570,7 @@

 &dsi1 {
 	interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+	compatible = "brcm,bcm2711-dsi1";
 };

 &gpio {
--- a/arch/arm/boot/dts/berlin2.dtsi
+++ b/arch/arm/boot/dts/berlin2.dtsi
@ -191,7 +191,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -209,7 +209,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -227,7 +227,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -245,7 +245,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -446,7 +446,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 				};
 			};
@ -461,7 +461,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
--- a/arch/arm/boot/dts/berlin2cd-google-chromecast.dts
+++ b/arch/arm/boot/dts/berlin2cd-google-chromecast.dts
@ -34,19 +34,19 @@
 		linux,usable-memory = <0x00000000 0x20000000>; /* 512 MB */
 	};

-	leds {
+	led-controller {
 		compatible = "pwm-leds";
 		pinctrl-0 = <&ledpwm_pmux>;
 		pinctrl-names = "default";

-		white {
+		led-1 {
 			label = "white";
 			pwms = <&pwm 0 600000 0>;
 			max-brightness = <255>;
 			linux,default-trigger = "default-on";
 		};

-		red {
+		led-2 {
 			label = "red";
 			pwms = <&pwm 1 600000 0>;
 			max-brightness = <255>;
--- a/arch/arm/boot/dts/berlin2cd.dtsi
+++ b/arch/arm/boot/dts/berlin2cd.dtsi
@ -181,7 +181,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -199,7 +199,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -217,7 +217,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -235,7 +235,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -473,7 +473,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 				};
 			};
@ -518,7 +518,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <8>;
+					ngpios = <8>;
 					reg = <0>;
 				};
 			};
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@ -252,7 +252,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -270,7 +270,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -288,7 +288,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -306,7 +306,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
@ -552,7 +552,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 				};
 			};
@ -613,7 +613,7 @@
 					compatible = "snps,dw-apb-gpio-port";
 					gpio-controller;
 					#gpio-cells = <2>;
-					snps,nr-gpios = <32>;
+					ngpios = <32>;
 					reg = <0>;
 				};
 			};
--- a/arch/arm/boot/dts/dra71-evm.dts
+++ b/arch/arm/boot/dts/dra71-evm.dts
@ -112,6 +112,8 @@
 				regulator-name = "lp8733-ldo0";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};

 			lp8733_ldo1_reg: ldo1 {
--- a/arch/arm/boot/dts/dra76x.dtsi
+++ b/arch/arm/boot/dts/dra76x.dtsi
@ -9,6 +9,13 @@
 	compatible = "ti,dra762", "ti,dra7";

 	ocp {
+		emif1: emif@4c000000 {
+			compatible = "ti,emif-dra7xx";
+			reg = <0x4c000000 0x200>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
 		target-module@42c01900 {
 			compatible = "ti,sysc-dra7-mcan", "ti,sysc";
 			ranges = <0x0 0x42c00000 0x2000>;
@ -133,3 +140,32 @@
 	/* dra76x is not affected by i887 */
 	max-frequency = <96000000>;
 };
+
+&cpu0_opp_table {
+	opp_plus@1800000000 {
+		opp-hz = /bits/ 64 <1800000000>;
+		opp-microvolt = <1250000 950000 1250000>,
+				<1250000 950000 1250000>;
+		opp-supported-hw = <0xFF 0x08>;
+	};
+};
+
+&opp_supply_mpu {
+	ti,efuse-settings = <
+	/* uV   offset */
+	1060000 0x0
+	1160000 0x4
+	1210000 0x8
+	1250000 0xC
+	>;
+};
+
+&abb_mpu {
+	ti,abb_info = <
+	/*uV		ABB	efuse	rbb_m fbb_m	vset_m*/
+	1060000		0	0x0	0 0x02000000 0x01F00000
+	1160000		0	0x4	0 0x02000000 0x01F00000
+	1210000		0	0x8	0 0x02000000 0x01F00000
+	1250000		0	0xC	0 0x02000000 0x01F00000
+	>;
+};
--- a/arch/arm/boot/dts/e60k02.dtsi
+++ b/arch/arm/boot/dts/e60k02.dtsi
@ -278,6 +278,12 @@
 };

 &uart1 {
+	/* J4, through-hole */
+	status = "okay";
+};
+
+&uart4 {
+	/* TP198, next to J4, SMD pads */
 	status = "okay";
 };

--- a/arch/arm/boot/dts/exynos3250-artik5.dtsi
+++ b/arch/arm/boot/dts/exynos3250-artik5.dtsi
@ -79,7 +79,7 @@
 	pmic@66 {
 		compatible = "samsung,s2mps14-pmic";
 		interrupt-parent = <&gpx3>;
-		interrupts = <5 IRQ_TYPE_NONE>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s2mps14_irq>;
 		reg = <0x66>;
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@ -200,7 +200,7 @@
 	pmic@66 {
 		compatible = "samsung,s2mps14-pmic";
 		interrupt-parent = <&gpx0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x66>;
 		wakeup-source;

--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@ -270,7 +270,7 @@
 	pmic@66 {
 		compatible = "samsung,s2mps14-pmic";
 		interrupt-parent = <&gpx0>;
-		interrupts = <7 IRQ_TYPE_NONE>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x66>;
 		wakeup-source;

--- a/arch/arm/boot/dts/exynos4210-i9100.dts
+++ b/arch/arm/boot/dts/exynos4210-i9100.dts
@ -560,20 +560,6 @@
 				regulator-boot-on;
 			};

-			charger_reg: CHARGER {
-				regulator-name = "CHARGER";
-				regulator-min-microamp = <60000>;
-				regulator-max-microamp = <2580000>;
-				regulator-always-on;
-			};
-
-			chargercv_reg: CHARGER_CV {
-				regulator-name = "CHARGER_CV";
-				regulator-min-microvolt = <3800000>;
-				regulator-max-microvolt = <4100000>;
-				regulator-always-on;
-			};
-
 			EN32KHZ_AP {
 				regulator-name = "EN32KHZ_AP";
 				regulator-always-on;
@ -583,6 +569,26 @@
 				regulator-name = "EN32KHZ_CP";
 				regulator-always-on;
 			};
+
+			charger_reg: CHARGER {
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <200000>;
+				regulator-max-microamp = <950000>;
+			};
+
+			chargercv_reg: CHARGER_CV {
+				regulator-name = "CHARGER_CV";
+				regulator-min-microvolt = <4200000>;
+				regulator-max-microvolt = <4200000>;
+				regulator-always-on;
+			};
+
+			CHARGER_TOPOFF {
+				regulator-name = "CHARGER_TOPOFF";
+				regulator-min-microamp = <200000>;
+				regulator-max-microamp = <200000>;
+				regulator-always-on;
+			};
 		};
 	};
 };
--- a/arch/arm/boot/dts/exynos5250-spring.dts
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@ -109,7 +109,7 @@
 		compatible = "samsung,s5m8767-pmic";
 		reg = <0x66>;
 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_NONE>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>;
 		wakeup-source;
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@ -349,7 +349,7 @@
 		reg = <0x66>;

 		interrupt-parent = <&gpx3>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s2mps11_irq>;

--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@ -509,7 +509,7 @@
 		samsung,s2mps11-acokb-ground;

 		interrupt-parent = <&gpx0>;
-		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&s2mps11_irq>;

--- a/arch/arm/boot/dts/exynos54xx.dtsi
+++ b/arch/arm/boot/dts/exynos54xx.dtsi
@ -188,7 +188,7 @@
 			compatible = "samsung,exynos4210-ehci";
 			reg = <0x12110000 0x100>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb2_phy 1>;
+			phys = <&usb2_phy 0>;
 			phy-names = "host";
 		};

@ -196,12 +196,12 @@
 			compatible = "samsung,exynos4210-ohci";
 			reg = <0x12120000 0x100>;
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb2_phy 1>;
+			phys = <&usb2_phy 0>;
 			phy-names = "host";
 		};

 		usb2_phy: phy@12130000 {
-			compatible = "samsung,exynos5250-usb2-phy";
+			compatible = "samsung,exynos5420-usb2-phy";
 			reg = <0x12130000 0x100>;
 			#phy-cells = <1>;
 		};
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@ -948,6 +948,16 @@
 					fsl,pull-up = <MXS_PULL_DISABLE>;
 				};

+				usb1_pins_b: usb1@1 {
+					reg = <1>;
+					fsl,pinmux-ids = <
+						MX28_PAD_PWM2__USB1_OVERCURRENT
+					>;
+					fsl,drive-strength = <MXS_DRIVE_12mA>;
+					fsl,voltage = <MXS_VOLTAGE_HIGH>;
+					fsl,pull-up = <MXS_PULL_DISABLE>;
+				};
+
 				usb0_id_pins_a: usb0id@0 {
 					reg = <0>;
 					fsl,pinmux-ids = <
--- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
+++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
@ -238,7 +238,6 @@
 		compatible = "wlf,wm8962";
 		reg = <0x1a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
-		clock-names = "xclk";
 		DCVDD-supply = <&reg_audio>;
 		DBVDD-supply = <&reg_audio>;
 		AVDD-supply = <&reg_audio>;
--- a/arch/arm/boot/dts/imx6dl-plybas.dts
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@ -0,0 +1,394 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent BAS board";
+	compatible = "ply,plybas", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		autorepeat;
+
+		button@20 {
+			label = "START";
+			linux,code = <31>;
+			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
+		};
+
+		button@21 {
+			label = "CLEAN";
+			linux,code = <46>;
+			gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-1 {
+			label = "debug1";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-2 {
+			label = "light_tower1";
+			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-3 {
+			label = "light_tower2";
+			gpios = <&gpio4 23 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-4 {
+			label = "light_tower3";
+			gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-5 {
+			label = "light_tower4";
+			gpios = <&gpio4 25 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "", "USB_EXT_PWR", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "", "",
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "IMX6_IN12", "IMX6_HMI",
+			"IMX6_IN11", "IMX6_BUZZER", "IMX6_LED1", "IMX6_LED2",
+		"IMX6_LED3", "IMX6_LED4", "ETH_RESET", "IMX6_ANA_OUT_SD",
+			"IMX6_ANA_OUT_ERR", "IMX6_ANA_OUT", "ETH_INTRP", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "IMX6_RELAY1", "IMX6_RELAY2", "",
+		"IMX6_IN1", "IMX6_IN2", "IMX6_IN3", "IMX6_IN4", "IMX6_IN5",
+			"IMX6_IN6", "IMX6_IN7", "IMX6_IN8",
+		"IMX6_IN9", "IMX6_IN10", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	fsl,uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-delay = <0 20>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG_0 */
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+			/* DEBUG_1 */
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09			0x1b0b0
+
+			/* LED1 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT1__GPIO4_IO22		0x13070
+			/* LED2 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT2__GPIO4_IO23		0x13070
+			/* LED3 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24		0x13070
+			/* LED4 (lighttower) */
+			MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25		0x13070
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B		0x130b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@ -0,0 +1,446 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Plymovent M2M board";
+	compatible = "ply,plym2m", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 1000>;
+		num-interpolated-steps = <20>;
+		default-brightness-level = <19>;
+		power-supply = <&reg_12v0>;
+	};
+
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	panel {
+		compatible = "edt,etm0700g0bdh6";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	xceiver-supply = <&reg_5v0>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio2 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-0 = <&pinctrl_tsc2046>;
+		pinctrl-names ="default";
+		spi-max-frequency = <100000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-max-pressure = <4095>;
+
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+
+		wakeup-source;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 23 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "", "", "", "", "", "",
+		"DEBUG_0", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ECSPI2_SS0", "", "", "", "TSC_BUSY", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "ECSPI1_SS1", "TSC_PENIRQ", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "ETH_RESET", "ETH_INTRP",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbphynop1 {
+	status = "disabled";
+};
+
+&usbphynop2 {
+	status = "disabled";
+};
+
+&usbotg {
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x1b000
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x3008
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x3008
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_OE__ECSPI2_MISO			0x10000
+			MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK			0x3008
+			MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI			0x3008
+			/* CS */
+			MX6QDL_PAD_EIM_RW__GPIO2_IO26			0x3008
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_CSI0_DAT4__GPIO5_IO22		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_CSI0_DAT5__GPIO5_IO23		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA			0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL			0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL			0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA			0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_disp: ipudisp1grp {
+		fsl,pins = <
+			/* DSE 0x30 => 25 Ohm, 0x20 => 37 Ohm, 0x10 => 75 Ohm */
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x30
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x30
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x30
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x30
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x30
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x30
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x30
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x30
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x30
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x30
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x30
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x30
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x30
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x30
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x30
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x30
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x30
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x30
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x30
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x30
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x30
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x30
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__PWM1_OUT			0x8
+		>;
+	};
+
+	pinctrl_tsc2046: tsc2046grp {
+		fsl,pins = <
+			/* TSC_PENIRQ */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x1b0b1
+			/* TSC_BUSY */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
--- a/arch/arm/boot/dts/imx6dl-prtmvt.dts
+++ b/arch/arm/boot/dts/imx6dl-prtmvt.dts
@ -0,0 +1,852 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Protonic MVT board";
+	compatible = "prt,prtmvt", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <1>;
+		power-supply = <&reg_3v3>;
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		f1 {
+			label = "GPIO Key F1";
+			linux,code = <KEY_F1>;
+			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
+		};
+
+		f2 {
+			label = "GPIO Key F2";
+			linux,code = <KEY_F2>;
+			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
+		};
+
+		f3 {
+			label = "GPIO Key F3";
+			linux,code = <KEY_F3>;
+			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
+		};
+
+		f4 {
+			label = "GPIO Key F4";
+			linux,code = <KEY_F4>;
+			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
+		};
+
+		f5 {
+			label = "GPIO Key F5";
+			linux,code = <KEY_F5>;
+			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
+		};
+
+		cycle {
+			label = "GPIO Key CYCLE";
+			linux,code = <KEY_CYCLEWINDOWS>;
+			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
+		};
+
+		esc {
+			label = "GPIO Key ESC";
+			linux,code = <KEY_ESC>;
+			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
+		};
+
+		up {
+			label = "GPIO Key UP";
+			linux,code = <KEY_UP>;
+			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
+		};
+
+		down {
+			label = "GPIO Key DOWN";
+			linux,code = <KEY_DOWN>;
+			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
+		};
+
+		ok {
+			label = "GPIO Key OK";
+			linux,code = <KEY_OK>;
+			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
+		};
+
+		f6 {
+			label = "GPIO Key F6";
+			linux,code = <KEY_F6>;
+			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
+		};
+
+		f7 {
+			label = "GPIO Key F7";
+			linux,code = <KEY_F7>;
+			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
+		};
+
+		f8 {
+			label = "GPIO Key F8";
+			linux,code = <KEY_F8>;
+			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
+		};
+
+		f9 {
+			label = "GPIO Key F9";
+			linux,code = <KEY_F9>;
+			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
+		};
+
+		f10 {
+			label = "GPIO Key F10";
+			linux,code = <KEY_F10>;
+			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
+		};
+
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "debug1";
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		led-2 {
+			label = "power_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg070wvlq", "lg,lb070wv8";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_h1_vbus: regulator-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "h1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0				IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-handle = <&rmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <3000>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
+			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "", "", "", "", "", "", "ON_SWITCH",
+		"POWER_LED", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+			"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
+		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+			"YACO_RESET";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "", "", "", "",
+		"CPU_LIGHT_ON", "", "ETH_RESET", "", "BL_EN",
+			"BL_PWM", "ETH_INTRP", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	video@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+
+	gpio_pca: gpio@74 {
+		compatible = "nxp,pca9539";
+		reg = <0x74>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca9539>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&ssi1 {
+	#sound-dai-cells = <0>;
+	fsl,mode = "ac97-slave";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_h1_vbus>;
+	pinctrl-names = "default";
+	phy_type = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* ITU656_nRESET */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
+			/* CAM1_MIRROR */
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
+			/* CAM2_MIRROR */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
+			/* CAM_nDETECT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
+			/* ISB_IN1 */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
+			/* ISB_nIN2 */
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
+			/* WARN_LIGHT */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
+			/* ON2_FB */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
+			/* YACO_nIRQ */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
+			/* YACO_BOOT0 */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
+			/* YACO_nRESET */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
+			/* FORCE_ON1 */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+			/* AUDIO_nRESET */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
+			/* ITU656_nPDN */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
+
+			/* HW revision detect */
+			/* REV_ID0 */
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
+			/* REV_ID1 */
+			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
+			/* REV_ID2 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
+			/* REV_ID3 */
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
+			/* REV_ID4 */
+			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
+
+			/* New in HW revision 1 */
+			/* ON1_FB */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
+			/* DIP1_FB */
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG0 */
+			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
+			/* DEBUG1 */
+			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
+			/* POWER_LED */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+		>;
+	};
+
+	pinctrl_pca9539: pca9539 {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+		>;
+	};
+
+	/* YaCO Touchscreen UART */
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@ -0,0 +1,852 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "Kverneland TGO";
+	compatible = "kvg,victgo", "fsl,imx6dl";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <1>;
+		power-supply = <&reg_3v3>;
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		enter {
+			label = "Rotary Key";
+			gpios = <&gpio2 05 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_ENTER>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "debug1";
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		led-2 {
+			label = "power_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg121xglp";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	clk50m_phy: phy-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_h1_vbus: regulator-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "h1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	rotary-encoder {
+		compatible = "rotary-encoder";
+		pinctrl-0 = <&pinctrl_rotary_ch>;
+		gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>,
+			<&gpio2 4 GPIO_ACTIVE_HIGH>;
+		linux,axis = <REL_WHEEL>;
+		rotary-encoder,steps-per-period = <4>;
+		rotary-encoder,relative-axis;
+		rotary-encoder,rollover;
+		wakeup-source;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0				IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	touchscreen@0 {
+		compatible = "ti,tsc2046";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		spi-max-frequency = <200000>;
+		interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>;
+		pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-y;
+		touchscreen-max-pressure = <4095>;
+		ti,vref-delay-usecs = /bits/ 16 <100>;
+		ti,x-plate-ohms = /bits/ 16 <800>;
+		ti,y-plate-ohms = /bits/ 16 <300>;
+		wakeup-source;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rmii";
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&clk50m_phy>;
+	clock-names = "ipg", "ahb", "ptp";
+	phy-handle = <&rmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
+			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
+		"POWER_LED", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+			"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
+		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+			"YACO_RESET";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
+		"CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
+			"BL_PWM", "ETH_INTRP", "ISB_LED";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
+			"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
+		"", "", "", "", "", "", "", "",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	video-decoder@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+
+	keypad@70 {
+		compatible = "holtek,ht16k33";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_keypad>;
+		reg = <0x70>;
+		refresh-rate-hz = <20>;
+		debounce-delay-ms = <50>;
+		interrupts-extended = <&gpio4 5 (IRQ_TYPE_LEVEL_HIGH | IRQ_TYPE_EDGE_RISING)>;
+		keypad,num-rows = <12>;
+		keypad,num-columns = <3>;
+		linux,keymap = <
+			MATRIX_KEY(2, 0, KEY_F6)
+			MATRIX_KEY(3, 0, KEY_F8)
+			MATRIX_KEY(4, 0, KEY_F10)
+			MATRIX_KEY(5, 0, KEY_F4)
+			MATRIX_KEY(6, 0, KEY_F2)
+			MATRIX_KEY(2, 1, KEY_F5)
+			MATRIX_KEY(3, 1, KEY_F7)
+			MATRIX_KEY(4, 1, KEY_F9)
+			MATRIX_KEY(5, 1, KEY_F3)
+			MATRIX_KEY(6, 1, KEY_F1)
+		      >;
+	};
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&ssi1 {
+	#sound-dai-cells = <0>;
+	fsl,mode = "ac97-slave";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_h1_vbus>;
+	pinctrl-names = "default";
+	phy_type = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI		0x100b1
+			MX6QDL_PAD_DISP0_DAT17__ECSPI2_MISO		0x100b1
+			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12		0x100b1
+			MX6QDL_PAD_DISP0_DAT19__ECSPI2_SCLK		0x100b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* MX6QDL_ENET_PINGRP4 */
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x1b0b0
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN		0x1b0b0
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0		0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN		0x1b0b0
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK		0x1b0b0
+			/* Phy reset */
+			MX6QDL_PAD_DISP0_DAT5__GPIO4_IO26		0x1b0b0
+			/* nINTRP */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x1b0b0
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* ROTARY_BTN */
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05			0x1b0b0
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* ITU656_nRESET */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
+			/* CAM1_MIRROR */
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
+			/* CAM2_MIRROR */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
+			/* CAM_nDETECT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
+			/* ISB_IN1 */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
+			/* ISB_nIN2 */
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
+			/* WARN_LIGHT */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
+			/* ON2_FB */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
+			/* YACO_nIRQ */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
+			/* YACO_BOOT0 */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
+			/* YACO_nRESET */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
+			/* FORCE_ON1 */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+			/* AUDIO_nRESET */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
+			/* ITU656_nPDN */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
+
+			/* HW revision detect */
+			/* REV_ID0 */
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
+			/* REV_ID1 is shared with PWM3 */
+			/* REV_ID2 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
+			/* REV_ID3 */
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
+			/* REV_ID4 */
+			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
+
+			/* New in HW revision 1 */
+			/* ON1_FB */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
+			/* DIP1_FB */
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+		>;
+	};
+
+	pinctrl_keypad: keypadgrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG0 */
+			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
+			/* DEBUG1 */
+			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
+			/* POWER_LED */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
+	pinctrl_rotary_ch: rotarychgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03			0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04			0x1b0b0
+		>;
+	};
+
+	pinctrl_touchscreen: touchscreengrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT14__GPIO5_IO08		0x1b0b0
+			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09		0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
+		>;
+	};
+
+	/* YaCO Touchscreen UART */
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+};
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+	model = "Kverneland UT1 Board";
+	compatible = "kvg,vicut1", "fsl,imx6dl";
+};
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+	model = "Kverneland UT1Q Board";
+	compatible = "kvg,vicut1q", "fsl,imx6q";
+};
+
+&sata {
+	status = "okay";
+};
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@ -406,19 +406,21 @@
 &hdmi {
 	compatible = "fsl,imx6q-hdmi";

-	port@2 {
-		reg = <2>;
+	ports {
+		port@2 {
+			reg = <2>;

-		hdmi_mux_2: endpoint {
-			remote-endpoint = <&ipu2_di0_hdmi>;
+			hdmi_mux_2: endpoint {
+				remote-endpoint = <&ipu2_di0_hdmi>;
+			};
 		};
-	};

-	port@3 {
-		reg = <3>;
+		port@3 {
+			reg = <3>;

-		hdmi_mux_3: endpoint {
-			remote-endpoint = <&ipu2_di1_hdmi>;
+			hdmi_mux_3: endpoint {
+				remote-endpoint = <&ipu2_di1_hdmi>;
+			};
 		};
 	};
 };
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@ -298,6 +298,7 @@
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
+	fsl,magic-packet;
 	status = "okay";
 };

--- a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
@ -69,11 +69,13 @@
 		ethernet-phy@0 {
 			reg = <0>;
 			qca,clk-out-frequency = <125000000>;
+			qca,smarteee-tw-us-1g = <24>;
 		};

 		ethernet-phy@4 {
 			reg = <4>;
 			qca,clk-out-frequency = <125000000>;
+			qca,smarteee-tw-us-1g = <24>;
 		};
 	};
 };
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@ -0,0 +1,803 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+#include <dt-bindings/display/sdtv-standards.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/media/tvp5150.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <1>;
+		power-supply = <&reg_3v3>;
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "LED_DI0_DEBUG_0";
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			label = "LED_DI0_DEBUG_1";
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "disk-activity";
+		};
+
+		led-2 {
+			label = "POWER_LED";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg121xglp";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	reg_1v8: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_h1_vbus: regulator-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "h1-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "otg-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		regulator-name = "wifi";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <70000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "prti6q-sgtl5000";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Line", "Line In Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "External Speaker";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"External Speaker", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&ssi1>;
+			system-clock-frequency = <0>; /* Do NOT call fsl_ssi_set_dai_sysclk! */
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&codec>;
+			bitclock-master;
+			frame-master;
+		};
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+
+	mux-ssi1 {
+		fsl,audmux-port = <0>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		0
+			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
+			IMX_AUDMUX_V2_PTCR_TFSDIR	0
+			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+		>;
+	};
+
+	mux-pins3 {
+		fsl,audmux-port = <2>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+			0				IMX_AUDMUX_V2_PDCR_TXRXEN
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
+	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ9031RNX PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3",
+			"SDIO_D2", "SDIO_D1", "SDIO_D0",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "", "",
+		"", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "",
+			"WL_IRQ", "ETH_MDC";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
+			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
+		"", "", "", "", "", "", "", "ON_SWITCH",
+		"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
+			"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
+		"", "", "", "", "BL_EN", "BL_PWM", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS",
+		"PCIE_RESET", "", "", "", "", "", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+			"RGMII_TD3",
+		"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+			"RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&gpio7 {
+	gpio-line-names =
+		"EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+			"EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+		"EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+		"", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0xa>;
+		#sound-dai-cells = <0>;
+		clocks = <&clks 201>;
+		VDDA-supply = <&reg_3v3>;
+		VDDIO-supply = <&reg_3v3>;
+		VDDD-supply = <&reg_1v8>;
+	};
+
+	video-decoder@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&ipu1_csi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ipu1_csi0>;
+	status = "okay";
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
+&ldb {
+	status = "okay";
+
+	lvds-channel@0 {
+		status = "okay";
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pcie {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&ssi1 {
+	#sound-dai-cells = <0>;
+	fsl,mode = "ac97-slave";
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_h1_vbus>;
+	pinctrl-names = "default";
+	phy_type = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_otg_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	phy_type = "utmi";
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_wifi>;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	no-1-8-v;
+	no-mmc;
+	no-sd;
+	status = "okay";
+
+	wifi {
+		compatible = "ti,wl1271";
+		interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+		ref-clock-frequency = "38400000";
+		tcxo-clock-frequency = "19200000";
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
+		>;
+	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
+			/* CAN1_SR */
+			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
+			/* CAN1_TERM */
+			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
+			/* CAN2_SR */
+			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
+			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
+			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
+			/* CS */
+			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x1b0b1
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* ITU656_nRESET */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
+			/* CAM1_MIRROR */
+			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
+			/* CAM2_MIRROR */
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
+			/* CAM_nDETECT */
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+			/* ISB_IN1 */
+			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
+			/* ISB_nIN2 */
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
+			/* WARN_LIGHT */
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
+			/* ON2_FB */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
+			/* YACO_nIRQ */
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
+			/* YACO_BOOT0 */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
+			/* YACO_nRESET */
+			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
+			/* FORCE_ON1 */
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
+			/* AUDIO_nRESET */
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
+			/* ITU656_nPDN */
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
+
+			/* HW revision detect */
+			/* REV_ID0 */
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
+			/* REV_ID1 */
+			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
+			/* REV_ID2 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
+			/* REV_ID3 */
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
+			/* REV_ID4 */
+			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
+
+			/* New in HW revision 1 */
+			/* ON1_FB */
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
+			/* DIP1_FB */
+			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
+
+			/* New in UT2: FIXME: ISB PWM should start off, PD */
+			/* ISB_LED_PWM */
+			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x130b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_ipu1_csi0: ipu1csi0grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			/* DEBUG0 */
+			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
+			/* DEBUG1 */
+			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
+			/* POWER_LED */
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D26__UART2_RX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D27__UART2_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B		0x1b0b1
+		>;
+	};
+
+	/* YaCO Touchscreen UART */
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
+			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
+			/* power enable, high active */
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
+			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
+			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD			0x170b9
+			MX6QDL_PAD_SD2_CLK__SD2_CLK			0x100b9
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0			0x170b9
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1			0x170b9
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2			0x170b9
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3			0x170b9
+			/* WL12xx IRQ */
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30		0x10880
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
+			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
+			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
+		>;
+	};
+
+	pinctrl_wifi_npd: wifinpdgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26		0x1b8b0
+		>;
+	};
+};
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@ -112,17 +112,17 @@

 	sound1 {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "Front";
+		simple-audio-card,name = "front";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&sound1_codec>;
 		simple-audio-card,frame-master = <&sound1_codec>;
 		simple-audio-card,widgets =
 			"Headphone", "Headphone Jack";
 		simple-audio-card,routing =
-			"Headphone Jack", "HPLEFT",
-			"Headphone Jack", "HPRIGHT",
-			"LEFTIN", "HPL",
-			"RIGHTIN", "HPR";
+			"Headphone Jack", "HPA1 HPLEFT",
+			"Headphone Jack", "HPA1 HPRIGHT",
+			"HPA1 LEFTIN", "HPL",
+			"HPA1 RIGHTIN", "HPR";
 		simple-audio-card,aux-devs = <&hpa1>;

 		sound1_cpu: simple-audio-card,cpu {
@ -137,17 +137,17 @@

 	sound2 {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "Back";
+		simple-audio-card,name = "periph";
 		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&sound2_codec>;
 		simple-audio-card,frame-master = <&sound2_codec>;
 		simple-audio-card,widgets =
 			"Headphone", "Headphone Jack";
 		simple-audio-card,routing =
-			"Headphone Jack", "HPLEFT",
-			"Headphone Jack", "HPRIGHT",
-			"LEFTIN", "HPL",
-			"RIGHTIN", "HPR";
+			"Headphone Jack", "HPA1 HPLEFT",
+			"Headphone Jack", "HPA1 HPRIGHT",
+			"HPA1 LEFTIN", "HPL",
+			"HPA1 RIGHTIN", "HPR";
 		simple-audio-card,aux-devs = <&hpa2>;

 		sound2_cpu: simple-audio-card,cpu {
@ -399,6 +399,7 @@
 		reg = <0x60>;
 		power-gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		Vdd-supply = <&reg_5p0v_main>;
+		sound-name-prefix = "HPA1";
 	};

 	edp-bridge@68 {
@ -598,6 +599,8 @@
 			touchscreen-inverted-x;
 			touchscreen-swapped-x-y;
 			syna,sensor-type = <1>;
+			syna,delta-x-threshold = <5>;
+			syna,delta-y-threshold = <10>;
 		};

 		rmi4-f12@12 {
@ -626,7 +629,7 @@
 		pinctrl-0 = <&pinctrl_ucs1002_pins>;
 		reg = <0x32>;
 		interrupts-extended = <&gpio5 2 IRQ_TYPE_EDGE_BOTH>,
-				      <&gpio3 21 IRQ_TYPE_EDGE_BOTH>;
+		                      <&gpio3 21 IRQ_TYPE_EDGE_FALLING>;
 		interrupt-names = "a_det", "alert";
 	};

@ -637,6 +640,7 @@
 		reg = <0x60>;
 		power-gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 		Vdd-supply = <&reg_5p0v_main>;
+		sound-name-prefix = "HPA1";
 	};
 };

@ -885,10 +889,6 @@
 	};
 };

-&wdog1 {
-	status = "disabled";
-};
-
 &iomuxc {
 	pinctrl_accel: accelgrp {
 		fsl,pins = <
@ -988,22 +988,22 @@

 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b8b1
-			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001b811
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001b811
 		>;
 	};

 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b8b1
-			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b8b1
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL		0x4001b811
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA		0x4001b811
 		>;
 	};

 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b8b1
-			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
+			MX6QDL_PAD_GPIO_3__I2C3_SCL		0x4001b811
+			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b811
 		>;
 	};

--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@ -182,8 +182,6 @@
 		};

 		hdmi: hdmi@120000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			reg = <0x00120000 0x9000>;
 			interrupts = <0 115 0x04>;
 			gpr = <&gpr>;
@ -192,19 +190,24 @@
 			clock-names = "iahb", "isfr";
 			status = "disabled";

-			port@0 {
-				reg = <0>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;

-				hdmi_mux_0: endpoint {
-					remote-endpoint = <&ipu1_di0_hdmi>;
+				port@0 {
+					reg = <0>;
+
+					hdmi_mux_0: endpoint {
+						remote-endpoint = <&ipu1_di0_hdmi>;
+					};
 				};
-			};

-			port@1 {
-				reg = <1>;
+				port@1 {
+					reg = <1>;

-				hdmi_mux_1: endpoint {
-					remote-endpoint = <&ipu1_di1_hdmi>;
+					hdmi_mux_1: endpoint {
+						remote-endpoint = <&ipu1_di1_hdmi>;
+					};
 				};
 			};
 		};
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6qp.dtsi"
+#include "imx6qdl-vicut1.dtsi"
+
+/ {
+	model = "Kverneland UT1P Board";
+	compatible = "kvg,vicutp", "fsl,imx6qp";
+};
--- a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
+++ b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
@ -340,7 +340,6 @@
 			MX6SL_PAD_KEY_ROW7__GPIO4_IO07		0x79
 			MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
 			MX6SL_PAD_KEY_COL5__GPIO4_IO02		0x79
-			MX6SL_PAD_KEY_ROW6__GPIO4_IO05		0x79
 		>;
 	};

@ -396,7 +395,14 @@
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
-			MX6SL_PAD_UART1_RXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
 		>;
 	};

@ -543,11 +549,19 @@
 };

 &uart1 {
+	/* J4, through-holes */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>;
 	status = "okay";
 };

+&uart4 {
+	/* TP198, next to J4, SMD pads */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
 	pinctrl-0 = <&pinctrl_usdhc2>;
--- a/arch/arm/boot/dts/imx6sl-tolino-shine3.dts
+++ b/arch/arm/boot/dts/imx6sl-tolino-shine3.dts
@ -94,7 +94,6 @@
 			MX6SL_PAD_KEY_ROW7__GPIO4_IO07		0x79
 			MX6SL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
 			MX6SL_PAD_KEY_COL5__GPIO4_IO02		0x79
-			MX6SL_PAD_KEY_ROW6__GPIO4_IO05		0x79
 		>;
 	};

@ -156,7 +155,14 @@
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1
-			MX6SL_PAD_UART1_RXD__UART1_TX_DATA 0x1b0b1
+			MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SL_PAD_KEY_ROW6__UART4_TX_DATA 0x1b0b1
+			MX6SL_PAD_KEY_COL6__UART4_RX_DATA 0x1b0b1
 		>;
 	};

@ -300,6 +306,11 @@
 	pinctrl-0 = <&pinctrl_uart1>;
 };

+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
 	pinctrl-0 = <&pinctrl_usdhc2>;
--- a/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts
+++ b/arch/arm/boot/dts/imx6sll-kobo-clarahd.dts
@ -104,7 +104,6 @@
 			MX6SLL_PAD_KEY_ROW7__GPIO4_IO07		0x79
 			MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13	0x79
 			MX6SLL_PAD_KEY_COL5__GPIO4_IO02		0x79
-			MX6SLL_PAD_KEY_ROW6__GPIO4_IO05		0x79
 		>;
 	};

@ -170,6 +169,13 @@
 		>;
 	};

+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6SLL_PAD_KEY_ROW6__UART4_DCE_TX 0x1b0b1
+			MX6SLL_PAD_KEY_COL6__UART4_DCE_RX 0x1b0b1
+		>;
+	};
+
 	pinctrl_usbotg1: usbotg1grp {
 		fsl,pins = <
 			MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
@ -302,6 +308,11 @@
 	pinctrl-0 = <&pinctrl_uart1>;
 };

+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz","sleep";
 	pinctrl-0 = <&pinctrl_usdhc2>;
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi
@ -206,6 +206,7 @@
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy1>;
 	phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	fsl,magic-packet;
 	status = "okay";

 	mdio {
@ -227,6 +228,7 @@
 	pinctrl-0 = <&pinctrl_enet2>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy2>;
+	fsl,magic-packet;
 	status = "okay";
 };

--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@ -101,7 +101,7 @@
 		status = "okay";
 		gpio-sck = <&gpio5 11 0>;
 		gpio-mosi = <&gpio5 10 0>;
-		cs-gpios = <&gpio5 7 0>;
+		cs-gpios = <&gpio5 7 GPIO_ACTIVE_LOW>;
 		num-chipselects = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@ -113,6 +113,7 @@
 			reg = <0>;
 			registers-number = <1>;
 			spi-max-frequency = <100000>;
+			enable-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 		};
 	};

@ -145,6 +146,41 @@
 		reg = <0x1a>;
 		wlf,shared-lrclk;
 	};
+
+	camera@3c {
+		compatible = "ovti,ov5640";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_camera_clock>;
+		clocks = <&clks IMX6UL_CLK_CSI>;
+		clock-names = "xclk";
+		powerdown-gpios = <&gpio_spi 6 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio_spi 5 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5640_to_parallel: endpoint {
+				remote-endpoint = <&parallel_from_ov5640>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <0>;
+				vsync-active = <0>;
+				pclk-sample = <1>;
+			};
+		};
+	};
+};
+
+&csi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_csi1>;
+	status = "okay";
+
+	port {
+		parallel_from_ov5640: endpoint {
+			remote-endpoint = <&ov5640_to_parallel>;
+			bus-type = <5>; /* Parallel bus */
+		};
+	};
 };

 &fec1 {
@ -169,17 +205,26 @@
 		#size-cells = <0>;

 		ethphy0: ethernet-phy@2 {
+			compatible = "ethernet-phy-id0022.1560";
 			reg = <2>;
 			micrel,led-mode = <1>;
 			clocks = <&clks IMX6UL_CLK_ENET_REF>;
 			clock-names = "rmii-ref";
+			reset-gpios = <&gpio_spi 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <100>;
+
 		};

 		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0022.1560";
 			reg = <1>;
 			micrel,led-mode = <1>;
 			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
 			clock-names = "rmii-ref";
+			reset-gpios = <&gpio_spi 2 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <100>;
 		};
 	};
 };
@ -343,9 +388,14 @@
 &iomuxc {
 	pinctrl-names = "default";

-	pinctrl_csi1: csi1grp {
+	pinctrl_camera_clock: cameraclockgrp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_MCLK__CSI_MCLK		0x1b088
+		>;
+	};
+
+	pinctrl_csi1: csi1grp {
+		fsl,pins = <
 			MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK	0x1b088
 			MX6UL_PAD_CSI_VSYNC__CSI_VSYNC		0x1b088
 			MX6UL_PAD_CSI_HSYNC__CSI_HSYNC		0x1b088
--- a/arch/arm/boot/dts/imx6ul-prti6g.dts
+++ b/arch/arm/boot/dts/imx6ul-prti6g.dts
@ -0,0 +1,356 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2016 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+#include "imx6ul.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Protonic PRTI6G Board";
+	compatible = "prt,prti6g", "fsl,imx6ul";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	clock_ksz8081_in: clock-ksz8081-in {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_ksz8081_out: clock-ksz8081-out {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			label = "debug0";
+			gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_3v2: regulator-3v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v2";
+		regulator-min-microvolt = <3200000>;
+		regulator-max-microvolt = <3200000>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	spi@0 {
+		compatible = "spidev";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eth1>;
+	phy-mode = "rmii";
+	phy-handle = <&rmii_phy>;
+	clocks = <&clks IMX6UL_CLK_ENET>,
+		 <&clks IMX6UL_CLK_ENET_AHB>,
+		 <&clks IMX6UL_CLK_ENET_PTP>,
+		 <&clock_ksz8081_out>;
+	clock-names = "ipg", "ahb", "ptp",
+		      "enet_clk_ref";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ8081RNA PHY */
+		rmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio5 1 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+			clocks = <&clock_ksz8081_in>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	/* additional i2c devices are added automatically by the boot loader */
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@4 {
+			reg = <4>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@6 {
+			reg = <6>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+
+		channel@7 {
+			reg = <7>;
+			ti,gain = <3>;
+			ti,datarate = <3>;
+		};
+	};
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+
+	temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_3v2>;
+	no-1-8-v;
+	disable-wp;
+	cap-sd-highspeed;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX		0x0b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX		0x0b0b0
+			/* SR */
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03		0x0b0b0
+			/* TERM */
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04		0x0b0b0
+			/* nSMBALERT */
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02		0x0b0b0
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX		0x0b0b0
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX		0x0b0b0
+			/* SR */
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05		0x0b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK		0x0b0b0
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26		0x000b1
+			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI		0x0b0b0
+			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO		0x0b0b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK		0x0b0b0
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22		0x000b1
+			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI		0x0b0b0
+			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO		0x0b0b0
+		>;
+	};
+
+	pinctrl_eth1: eth1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC			0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO		0x100b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00		0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01		0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN		0x100b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER		0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN		0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00		0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01		0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1		0x1b000
+			/* PHY ENET1_RST */
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00		0x00880
+			/* PHY ENET1_IRQ */
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01		0x00880
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* HW revision detect */
+			/* REV_ID0 */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08		0x1b0b0
+			/* REV_ID1 */
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09		0x1b0b0
+			/* REV_ID2 */
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10		0x1b0b0
+			/* REV_ID3 */
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11		0x1b0b0
+			/* BOARD_ID0 */
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13		0x1b0b0
+			/* BOARD_ID1 */
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14		0x1b0b0
+			/* BOARD_ID2 */
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15		0x1b0b0
+			/* BOARD_ID3 */
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12		0x1b0b0
+			/* Safety controller IO */
+			/* WAKE_SC */
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06		0x1b0b0
+			/* PROGRAM_SC */
+			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__I2C2_SDA		0x4001b8b0
+			MX6UL_PAD_CSI_HSYNC__I2C2_SCL		0x4001b8b0
+		>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16			0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX		0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD			0x070b1
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK			0x07099
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0		0x070b1
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1		0x070b1
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2		0x070b1
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3		0x070b1
+			/* SD1 CD */
+			MX6UL_PAD_NAND_READY_B__GPIO4_IO12		0x170b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD			0x170f9
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK			0x100f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0		0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1		0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2		0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3		0x170f9
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4		0x170f9
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5		0x170f9
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6		0x170f9
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7		0x170f9
+			MX6UL_PAD_NAND_ALE__USDHC2_RESET_B		0x170b0
+		>;
+	};
+};
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@ -538,6 +538,7 @@
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
 				fsl,stop-mode = <&gpr 0x10 4>;
+				fsl,magic-packet;
 				status = "disabled";
 			};

@ -885,6 +886,7 @@
 				fsl,num-tx-queues = <1>;
 				fsl,num-rx-queues = <1>;
 				fsl,stop-mode = <&gpr 0x10 3>;
+				fsl,magic-packet;
 				status = "disabled";
 			};

--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/imx7s.dtsi
@ -151,6 +151,7 @@

 	timer {
 		compatible = "arm,armv7-timer";
+		arm,cpu-registers-not-fw-configured;
 		interrupt-parent = <&intc>;
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
--- a/Show More
+++ b/Show More